BUILDER/COMFORT BATH SERIES
ELECTRONIC & MANUAL CONTROLS
INSTALLATION AND OPERATING INSTRUCTIONS
Save These Instructions for Future Use.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number _____________________________________________________________
Model_____________________________________________________________________
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
©2005 Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND
FAULT CIRCUIT INTERRUPTER (GFCI).
CAUTION — TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE
PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS.
WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT
USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURERS.
WARNING—TOAVOIDINJURY,EXERCISECAUTIONWHENENTERINGOREXITINGTHEHYDROMASSAGEBATHTUB.
WARNING — KEEP BODY AND HAIR A MINIMUM OF 6" AWAY FROM SUCTION FITTING AT ALL TIMES
WHEN THE HYDROMASSAGE SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER LENGTH
SHOULD BE SECURED CLOSE TO THE HEAD.
WARNING—RISKOFELECTRICALSHOCK;DONOTPERMITELECTRICALAPPLIANCES(SUCHASHAIRDRYER,
LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1.5 M) OF THIS HYDROMASSAGE BATHTUB.
WARNING — RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL
BEFORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING — RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD
CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING — RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE
BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
WARNING—RISKOFHYPERTHERMIAANDPOSSIBLEDROWNING;WATERTEMPERATUREINEXCESS
OF 104°F (40°C) MAY BE INJURIOUS TO YOUR HEALTH. CHECK AND ADJUST WATER TEMPERATURE
BEFORE USE.
WARNING — RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER.
FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMIT ACCESS FOR SERVICING.
THIS UNIT SHOULD BE ELECTRICALLY GROUNDEDAND INSTALLED BYALICENSED CONTRACTOR,
ELECTRICIAN, AND PLUMBER.
BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR
BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT.
A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND
HEATER TO PERMITCONNECTION OFAN NO. 8AWG (8.4 MM) SOLID COPPER BONDING CONDUCTOR
BETWEEN THIS UNITAND ALL OTHER ELECTRIC EQUIPMENTAND EXPOSED METAL IN THE VICINITY,
AS NEEDED TO COMPLY WITH LOCAL REQUIREMENTS.
PRECAUTIONS
•
Do not operate the hydromassage system unless the bath is filled with water to at least 1" to 2" (2,5 - 5,08 cm) above the
highest jet.
•
•
•
•
Do not immerse the control panel by overfilling the bath.
Do not use oil-based bath additives in your hydromassage bath.
When cleaning your bath, do not use abrasive substances which will damage the bath's surface.
To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
NOTE: This is a professional grade product. Aknowledge of construction techniques, plumbing and electri-
cal installation according to codes are required for proper installation and user satisfaction. We recommend
that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does
not cover improper installation related problems.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
The Company has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. The
Company makes no representation or warranty regarding, and will not be responsible for any code compliance.
3
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Safety Instructions _____________________________________________________________________ 2-3
Contents _____________________________________________________________________________ 4
Specifications _________________________________________________________________________ 5-9
Roughing-in __________________________________________________________________________ 10-17
Cutout ______________________________________________________________________________ 17
Installation Instructions __________________________________________________________________ 18-24
Framing and Support _________________________________________________________________ 18
Skirts ______________________________________________________________________________ 19
Service Access _____________________________________________________________________ 20
Electrical Connections ________________________________________________________________ 21
Plumbing and Water Supply ___________________________________________________________ 22
Undermount Installation Instructions _____________________________________________________ 23-24
Operation ____________________________________________________________________________ 25-26
Maintenance __________________________________________________________________________ 27
General Troubleshooting Guide ___________________________________________________________ 28
Authorized Service _____________________________________________________________________ 30
Warranty _____________________________________________________________________________ 31-32
NOTE: If you need a referral for a service company near you, or need assistance with operation or maintenance
related questions, please call our USA Service Support Department at 1-800-288-4002. Visit our web site at http:/
/www.jacuzzi.com/ for products and services.
To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
4
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings
necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do
not lift the bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do
not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi
Whirlpool Bath responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any
claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty informa-
tion packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. NOTE: Prior to installa-
tion, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage
or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or
avoided by following this inspection and testing procedure.
Not all tubs shown may be available as export units. Export tubs come with MANUAL controls and may come:
• with Pump/motor packaged separately,
• with Pump/motor installed,
• with NO overflow cutout.
Because of the variety of export tub types some instructions may not apply to your unit. Disregard instructions that do not
apply to your specific tub.
RECTANGULAR BATHS
L
W
L
(25 mm)
1"
W
2"
(51 mm)
H
H
END VIEW
SIDE VIEW
SIDE VIEW
END VIEW
BATHS WITHOUT INTEGRAL SKIRT
BATHS WITH INTEGRAL SKIRT
(25 mm)
1"
L
W
H
A
END VIEW
SIDE VIEW
B
BATHS WITH 3-SIDED TILE FLANGE
SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand
DRAIN/OVERFLOW
HEATER READY
FOR FIELD
INSTALLATION
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/ OPERATING
FLOOR LOADING GALLONAGE
PRODUCT
WEIGHT
SKIRT &
MOUNTING
CUTOUT
MODEL
AMIGA™
DIMENSIONS
70" x 34"
(1778 mm x
864 mm)
Yes
16-7/8" (429 mm) A
772 lb
(351 kg)/
43 lb/ft2
50 U.S. gal
(186 liters)
105 lb
(48 kg)
Optional,
U-Frame
72"
36"
(1829 mm) L*
( 914 mm) W
20-3/4" ( 533 mm) H
(S750000 HEATER KIT)
14"
(356 mm) B
LH & RH
(210 kg/m2)
NA
AMIGA™
WITH INTEGRAL
SKIRT
16-7/8" (429 mm) A
50 U.S. gal
(186 liters)
Integral
796 lb
(362 kg)/
44 lb/ft2
129 lb
(59 kg)
Yes
72"
36"
(1829 mm) L*
( 914 mm) W
14"
(356 mm) B
(S750000 HEATER KIT)
20-3/4" ( 533 mm) H
(214 kg/m2)
LH & RH
BIANCA©
Yes
16"
(406 mm) A
70" x 46"
73 U.S. gal
(276 liters)
993 lb
(451 kg)/
41 lb/ft2
135 lb
(61 kg)
Optional,
U-Frame
72"
48"
(1829 mm) L*
(1219 mm) W
(S750000 HEATER KIT)
8-1/2" (216 mm) B (1778 mm x
1168 mm)
LH
20-1/2" ( 521 mm) H
(200 kg/m2)
CETRA©
46 U.S. gal
(174 liters)
Integral
17-7/8" (454 mm) A
9-3/8" (238 mm) B
NA
Yes
727 lb
(330 kg)/
55 lb/ft2
(268 kg/m2)
94 lb
(43 kg)
60"
32"
(1524 mm) L*
( 813 mm) W
(S750000 HEATER KIT)
WITH INTEGRAL
SKIRT
LH & RH
20-1/2" ( 521 mm) H
Yes
CETRA© 532
LH & RH
43 U.S. gal
(163 liters)
Optional
U-Frame
58" x 30-1/4"
(1473 mm x
768 mm)
18-1/2" ( 470 mm) A
697 lb
(317 kg)/
53 lb/ft2
(259 kg/m2)
89 lb
(41 kg)
60"
(1524 mm) L*
(S750000 HEATER KIT)
9"
( 229 mm) B
31-7/8" ( 791 mm) W
21-1/4" ( 553 mm) H
CETRA© 536
LH & RH
48 U.S. gal
(181 liters)
Optional
U-Frame
58" x 34-1/4"
(1473 mm x
870 mm)
Yes
18-1/2" ( 470 mm) A
742 lb
(337 kg)/
50 lb/ft2
(244 kg/m2)
92 lb
(42 kg)
60"
36"
(1524 mm) L*
( 914 mm) W
(S750000 HEATER KIT)
9"
( 229 mm) B
21-1/4" ( 553 mm) H
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
5
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand
HEATER READY
FOR FIELD
INSTALLATION
OPERATING PRODUCT
GALLONAGE WEIGHT
SKIRT &
MOUNTING
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/
FLOOR LOADING
MODEL
DIMENSIONS
(1524 mm) L*
CUTOUT
Yes
CETRA© 536
WITH INTEGRAL
SKIRT
NA
742 lb
(337 kg)/
50 lb/ft2
(244 kg/m2)
92 lb
Integral
60"
36"
48 U.S. gal
18-1/2" ( 470 mm) A
(S750000 HEATER KIT)
(42 kg)
(181 liters)
9"
( 229 mm) B
( 914 mm) W
21-1/4" ( 553 mm) H
LH & RH
697 lb
(264 kg)/
52 lb/ft2
(254 kg/m2)
Yes
LUXURA™ 5
WITH INTEGRAL
3-SIDED TILE
FLANGE
NA
Molded-in
Tile Flange
80 lb
(36 kg)
Optional,
U-Frame
60"
32"
(1524 mm) L*
44 U.S. gal
(167 liters)
15-1/4" (387 mm) A
8-1/4" (210 mm) B
(S750000 HEATER KIT)
( 813 mm) W
20-1/4" ( 514 mm) H
LH & RH
Yes
LUXURA™5
WITH INTEGRAL 32"
SKIRT
LH & RH
60"
(1524 mm) L
( 813 mm) W
NA
700 lb
(318 kg)/
53 lb/ft2
100 lb
(45 kg)
Integral
15-1/4" (387 mm) A
8-1/4" (210 mm) B
42 U.S. gal
(159 liters)
(S750000 HEATER KIT)
20-1/4" ( 514 mm) H
(259 kg/m2)
Yes
66"
(1676 mm) L*
( 864 mm) W
( 508 mm) H
LUXURA™ 5.5
LH & RH
Optional,
U-Frame
15-1/4" (387 mm) A
8-3/8" (213 mm) B (1626 mm x
813 mm)
64" x 32"
823 lb
(374 kg)/
53 lb/ft2
(259 kg/m2)
90 lb
(41 kg)
58 U.S. gal
(220 liters)
(S750000 HEATER KIT)
34"
20"
Yes
60"
30"
(1524 mm) L* 16-3/4" (425 mm) A
Integral
662 lb
(301 kg)/
53 lb/ft2
LUXURA™ 530
WITH INTEGRAL
SKIRT
NA
95 lb
(43 kg)
38 U.S. gal
(144 liters)
(U395000 HEATER KIT)
9-1/4" (235 mm) B
( 762 mm) W
20-1/4" ( 483 mm) H
(259 kg/m2)
LH & RH
Yes
MAJORA©
LH & RH
5
58" x 40"
728 lb
(331 kg)/
42 lb/ft2
(205 kg/m2)
46 U.S. gal
(172 liters)
95 lb
(43 kg)
Not
Available
15"
(381 mm) A
60"
42"
(1524 mm) L*
(1067 mm) W
(S750000 HEATER KIT)
8-3/4" (222 mm) B (1473 mm x
1016 mm)
19-1/2" ( 495 mm) H
Yes
MAJORA©
LH & RH
6
72"
42"
(1829 mm) L* 15-5/8" (397 mm) A
70 U.S. gal
(265 liters)
104 lb
(47 kg)
Not
Available
937 lb
(423 kg)/
44 lb/ft2
(215 kg/m2)
70" x 40"
(1778 mm x
1016 mm)
(S750000 HEATER KIT)
10-1/2" (267 mm) B
(1067 mm) W
19-3/4" ( 502 mm) H
MAJORA©
6
15-5/8" (397 mm) A
10-1/2" (267 mm) B
NA
947 lb
(430 kg)/
45 lb/ft2
(220 kg/m2)
114 lb
(52 kg)
Integral
70 U.S. gal
(265 liters)
Yes
72"
42"
(1829 mm) L*
(1067 mm) W
WITH INTEGRAL
SKIRT
LH & RH
(S750000 HEATER KIT)
19-3/4" ( 502 mm) H
MITO©
5
866 lb
(394 kg)/
50 lb/ft2
62 U.S. gal
(235 liters)
100 lb
(45 kg)
Optional,
U-Frame
17-1/2" (445 mm) A
11-7/8" (302 mm) B
58" x 40"
(1473 mm x
1016 mm)
Yes
60" (1524 mm) L*
(S750000 HEATER KIT)
42" (1067 mm) W
21" ( 533 mm) H
LH & RH
(244 kg/m2)
MITO©
LH & RH
NOVA©
LH & RH
6
17-1/2" (445 mm) A
(1067 mm) W 11-7/8" (302 mm) B
76 U.S. gal
(288 liters)
110 lb
(50 kg)
72"
42"
(1829 mm) L*
Not
Available
993 lb
(451 kg)/
47 lb/ft2
Yes
70" x 40"
(1778 mm x
1016 mm)
(S750000 HEATER KIT)
21-1/2" ( 546 mm) H
(229 kg/m2)
5
58" x 40"
(1473 mm x
1016 mm)
46 U.S. gal
(170 liters)
Optional,
U-Frame
14-3/4" (375 mm) A
8-1/2" (216 mm) B
722 lb
(328 kg)/
41 lb/ft2
(200 kg/m2)
97 lb
(44 kg)
Yes
60"
42"
(1524 mm) L*
(1067 mm) W
(S750000 HEATER KIT)
18-1/2" ( 470 mm) H
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
6
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand
HEATER READY
FOR FIELD
INSTALLATION
SKIRT &
MOUNTING
PRODUCT
WEIGHT
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/
FLOOR LOADING
OPERATING
GALLONAGE
MODEL
DIMENSIONS
CUTOUT
NOVA©
5
Yes
NA
Molded-in
Tile Flange
722 lb
(328 kg)/
41 lb/ft2
(200 kg/m2)
46 U.S. gal
(174 liters)
97 lb
(44 kg)
Not
Available
14-3/4" (375 mm) A
8-1/2" (216 mm) B
60"
42"
(1524 mm) L*
(1067 mm) W
WITH INTEGRAL
3-SIDED TILE
FLANGE
(S750000 HEATER KIT)
18-1/2" ( 470 mm) H
LH & RH
NOVA©
WITH INTEGRAL
SKIRT
LH & RH
15-7/8" (403 mm) A
9-1/4" (235 mm) B
5
NA
737 lb
(335 kg)/
42 lb/ft2
(205 kg/m2)
45 U.S. gal
(174 liters)
112 lb
(51 kg)
No
60"
42"
(1524 mm) L*
(1067 mm) W
Integral
18-1/2" ( 470 mm) H
NOVA©
6
70" x 40"
(1778 mm x
1016 mm)
14-3/4" (375 mm) A
8-1/2" (216 mm) B
876 lb
(398 kg)/
42 lb/ft2
110 lb
(50 kg)
Yes
62 U.S. gal
(235 liters)
Optional,
U-Frame
72"
42"
(1829 mm) L*
(S750000 HEATER KIT)
(1067 mm) W
LH & RH
20-1/2" ( 521 mm) H
(205 kg/m2)
683 lb
(310 kg)/
46 lb/ft2
(224 kg/m2)
Yes
NOVA© 536
LH & RH
Not
Available
15-1/8" (384 mm) A
58" x 34"
42 U.S. gal
(159 liters)
83 lb
(38 kg)
60"
36"
(1524 mm) L*
(S750000 HEATER KIT)
9"
(229 mm) B (1473 mm x
863 mm)
( 914 mm) W
19-1/4" ( 489 mm) H
NOVA© 536
WITH INTEGRAL
SKIRT
14-5/8" (372 mm) A
9" (229 mm) B
42 U.S. gal
(159 liters)
98 lb
(45 kg)
698 lb
(317 kg)/
47 lb/ft2
NA
NA
Yes
60"
36"
(1524 mm) L*
( 914 mm) W
Integral
Integral
(S750000 HEATER KIT)
19-1/4" ( 489 mm) H
(229 kg/m2)
LH & RH
NOVA© 636
WITH INTEGRAL
SKIRT
14-5/8" (372 mm) A
9-3/8" (238 mm) B
Yes
56 U.S. gal
(223 liters)
824 lb
(375 kg)/
45.8 lb/ft2
(223 kg/m2)
108 lb
(49 kg)
72"
(1829 mm) L*
( 914 mm) W
( 483 mm) H
(S750000 HEATER KIT)
36"
19"
LH & RH
SIGNA©
5
42 U.S. gal
(159 liters)
Optional,
U-Frame
17-1/2" (445 mm) A
12-1/2" (318 mm) B
708 lb
(321 kg)/
40 lb/ft2
108 lb
(49 kg)
60"
(1524 mm) L*
58" x 40"
(1473 mm x
1016 mm)
Yes
(S750000 HEATER KIT)
42"
22"
(1067 mm) W
( 559 mm) H
LH & RH
(195 kg/m2)
SIGNA© 5 WITH
INTEGRAL SKIRT,
FRONT RIGHT
MOTOR/PUMP
LH & RH
42 U.S. gal
(159 liters)
123 lb
(56 kg)
723 lb
(329 kg)/
41 lb/ft2
(200 kg/m2)
17-7/8" (451 mm) A
12-3/4" (330 mm) B
Integral
NA
Yes
60"
(1524 mm) L*
(1067 mm) W
( 559 mm) H
(U395000 HEATER KIT)
42"
22"
Yes
SIGNA©
5
60"
(1524 mm) L*
(1067 mm) W
( 559 mm) H
Optional,
U-Frame
17-1/2" (445 mm) A
12-1/2" (318 mm) B
NA
708 lb
(321 kg)/
40 lb/ft2
(195 kg/m2)
108 lb
(49 kg)
42 U.S. gal
(159 liters)
(S750000 HEATER KIT)
WITH INTEGRAL 42"
3-SIDED TILE
FLANGE
RH
22"
826 lb
(375 kg)/
39 lb/ft2
(190 kg/m2)
SIGNA©
6
70" x 40"
(1778 mm x
1016 mm)
16-7/8" (429 mm) A
118 lb
(54 kg)
55 U.S. gal
(208 liters)
Yes
Not
Available
72"
(1829 mm) L*
14"
(356 mm) B
(S750000 HEATER KIT)
42"
22"
(1067 mm) W
( 559 mm) H
LH & RH
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
7
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
RIMLESS OVAL BATHS
W
L
L
W
2'' (51 mm)
7-1/2"
(191 mm)
3-1/2"
(89 mm)
8"
H
H
2"
(203 mm)
(51 mm)
END VIEW
W
SIDE VIEW
END VIEW
SIDE VIEW
MILANO
FRESCO
L
W
L
2"
2''
(51 mm)
(51 mm)
H
H
SIDE VIEW
END VIEW
END VIEW
SIDE VIEW
LUNA
RIVA 5 & RIVA 6
GALLERY 5 OVAL & GALLERY 6 OVAL
A
B
DRAIN/OVERFLOW
SPECIFICATIONS (Oval) LH = Left Hand, RH = Right Hand
HEATER READY
FOR FIELD
INSTALLATION
SKIRT &
MOUNTING
PRODUCT
WEIGHT
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/
FLOOR LOADING
OPERATING
GALLONAGE
DIMENSIONS
MODEL
FRESCO©
LH & RH
CUTOUT
Yes
71-1/2" (1816 mm) L
(1067 mm) W
27-1/4" ( 692 mm) H*
20-1/8" (511 mm) A
11-3/4" (299 mm) B
Template
Provided
P/N
921 lb
(419 kg)/
44 lb/ft2
(220 kg/m2)
63 U.S. gal
(239 liters)
146 lb
(66 kg)
Not
Available
(S750000 HEATER KIT)
42"
P188000
GALLERY™ 5 62"
(1575 mm) L
(1092 mm) W 9-1/2" (241 mm) B
( 483 mm) H
14-3/4" (375 mm) A
Template
Provided
P/N
746 lb
(339 kg)/
40 lb/ft2
(195 kg/m2)
48 U.S. gal
(182 liters)
96 lb
(44 kg)
Not
Available
Yes
OVAL
43"
19"
(S750000 HEATER KIT)
LH & RH
P186000
GALLERY™ 6
OVAL
871 lb
(395 kg)/
42 lb/ft2
(205 kg/m2)
Yes
72"
42"
(1829 mm) L
(1067 mm) W 11-1/2" (292 mm) B
16"
(406 mm) A
105 lb
(48 kg)
Template
Provided
P/N
62 U.S. gal
(235 liters)
Not
Available
(S750000 HEATER KIT)
20-1/2" ( 521 mm) H
LH & RH
P186000
GALLERY™ 6
OVAL
UNDERMOUNT
Yes
871 lb
(395 kg)/
42 lb/ft2
72"
42"
(1829 mm) L
(1067 mm) W 11-1/2" (292 mm) B
16"
(406 mm) A
105 lb
(48 kg)
62 U.S. gal
(235 liters)
Not
Available
Template
Provided
P/N
(S750000 HEATER KIT)
20-1/2" ( 521 mm) H
(205 kg/m2)
X302000
LH & RH
LUNA™
72"
42"
23"
(1829 mm) L
(1067 mm) W 11"
( 584 mm) H
19-1/8" (486 mm) A
Template
Provided
P/N
1221 lb
(555 kg)/
58 lb/ft2
(283 kg/m2)
96 U.S. gal
(364 liters)
121 lb
(55 kg)
Not
Available
Yes
(279 mm) B
(S750000 HEATER KIT)
RH
P819000
Yes
MILANO™
LH & RH
72"
40"
(1829 mm) L
(1016 mm) W 11"
18-1/2" (470 mm) A
(279 mm) B
Template
Provided
P/N
893 lb
(406 kg)/
45 lb/ft2
60 U.S. gal
(227 liters)
143 lb
(65 kg)
Not
Available
(S750000 HEATER KIT)
20-3/4" ( 527 mm) H
P188000
(220 kg/m2)
Yes
OPALIA™
LH & RH
72"
44"
(1829 mm) L 18-3/4" (476 mm) A
(1118 mm) W 12" (305 mm) B
Template
Provided
P/N
978 lb
(445 kg)/
45 lb/ft2
(220 kg/m2)
70 U.S. gal
(265 liters)
145 lb
(66 kg)
Not
Available
(S750000 HEATER KIT)
22-1/4" ( 565 mm) H
P186000
RIVA©
5
62"
43"
19"
(1575 mm) L
(1092 mm) W 9-1/2" (241 mm) B
( 483 mm) H
14-3/4" (375 mm) A Template
746 lb
(339 kg)/
40 lb/ft2
(195 kg/m2)
48 U.S. gal
(182 liters)
96 lb
(44 kg)
Not
Available
Yes
(S750000 HEATER KIT)
Provided
P/N
P186000
LH & RH
RIVA©
6
72"
42"
(1829 mm) L
(1067 mm) W 11-1/2" (292 mm) B
16"
(406 mm) A
Template
Provided
P/N
871 lb
(396 kg)/
42 lb/ft2
(205 kg/m2)
62 U.S. gal
(235 liters)
105 lb
(48 kg)
Not
Available
Yes
(S750000 HEATER KIT)
LH & RH
20-1/2" ( 521 mm) H
P186000
* For Fresco™ models H551, H549, and H550 this height is 23-3/4"
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
8
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
CORNER BATHS
A
2"
H
(51 mm)
B
DRAIN/OVERFLOW
END VIEW
SIDE VIEW
CORNER BATH
1"
H
(25 mm)
FRONT VIEW
SIDE VIEW
CAPELLA 55, CAPELLA 60, & TARA WITH INTEGRAL SKIRT
1"
H
(25 mm)
FRONT VIEW
CAPELLA SPACESAVER WITH INTEGRAL SKIRT
SIDE VIEW
SPECIFICATIONS (Corner) LH = Left Hand, RH = Right Hand
HEATER READY
FOR FIELD
INSTALLATION
SKIRT &
MOUNTING
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/ OPERATING PRODUCT
WEIGHT
DIMENSIONS
CUTOUT FLOOR LOADING GALLONAGE
MODEL
CAPELLA© 55
55"
55"
(1397 mm) L
(1397 mm) L
51 U.S. gal
(193 liters)
Yes
17-1/2" (445 mm) A
9-5/8" (245 mm) B
791 lb
(360 kg)/
38 lb/ft2
(185 kg/m2)
116 lb
(53 kg)
Optional
Template
Provided
P/N
(S750000 HEATER KIT)
RH
20-1/4" ( 514 mm) H
DA24000
CAPELLA© 55
WITH INTEGRAL 55"
55"
(1397 mm) L
(1397 mm) L
18"
(457 mm) A
NA
54 U.S. gal
(204 liters)
1025 lb
(466 kg)/
125 lb
(57 kg)
Integral
Integral
No
No
12-1/8" (308 mm) B
48.8 lb/ft2
(238 kg/m2)
SKIRT
RH
20-1/2" ( 521 mm) H
CAPELLA©
SPACESAVER
WITH INTEGRAL 20-1/2" ( 521 mm) H
SKIRT RH
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
NA
60 U.S. gal
(227 liters)
880 lb
(400 kg)/
35 lb/ft2
(171 kg/m2)
130 lb
(59 kg)
12-3/8" (308 mm) B
CAPELLA© 60
FRONT LEFT
MOTOR/PUMP
LH
See
Page 17
60 U.S. gal
(227 liters)
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
870 lb
(395 kg)/
35 lb/ft2
120 lb
(54 kg)
Not
Available
No
No
12-1/8" (308 mm) B
20-1/2" ( 521 mm) H
(171 kg/m2)
CAPELLA© 60
LH & RH
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
See
Page 17
60 U.S. gal
(227 liters)
870 lb
(395 kg)/
35 lb/ft2
120 lb
(54 kg)
Not
Available
12-1/8" (308 mm) B
20-1/2" ( 521 mm) H
(171 kg/m2)
CAPELLA© 60
WITH INTEGRAL
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
NA
60 U.S. gal
(227 liters)
880 lb
(400 kg)/
35 lb/ft2
(171 kg/m2)
130 lb
(59 kg)
Integral
No
12-1/8" (308 mm) B
SKIRT
RH
20-1/2" ( 521 mm) H
Yes
74 U.S. gal
(280 liters)
See
Page 17
18-1/8" (451 mm) A
984 lb
(447 kg)/
39 lb/ft2
118 lb
(54 kg)
GALLERY™
CORNER
Not
Available
60"
60"
(1524 mm) L
(1524 mm) L
(S750000 HEATER KIT)
12"
16"
(305 mm) B
(406 mm) A
22-1/2" ( 572 mm) H
(244 kg/m2)
LH & RH
TARA™
LH & RH
118 lb
(54 kg)
Optional
Integral
See
Page 17
Yes
60"
60"
(1524 mm) L
(1524 mm) L
74 U.S. gal
(280 liters)
984 lb
(447 kg)/
39 lb/ft2
(190 kg/m2)
(S750000 HEATER KIT)
12-3/8" (314 mm) B
20-3/4" ( 527 mm) H
999 lb
(454 kg)/
40 lb/ft2
TARA™
WITH INTEGRAL 60"
SKIRT RH
60"
(1524 mm) L
(1524 mm) L
16"
(406 mm) A
74 U.S. gal
(280 liters)
No
133 lb
(61 kg)
NA
12-3/8" (314 mm) B
20-3/4" ( 527 mm) H
(195 kg/m2)
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
9
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (RECTANGULAR)
*72''
*72''
*72''
Motor
17-3/8"
18''
18''
Motor
Motor
16'' x 4''
16'' x 4''
16'' x 4''
36''
36''
36''
11-1/8''
11-1/8''
2''
Opt. Service Access
14''
AMIGA™, Right Hand
11-1/8''
2''
Opt. Service Access
2''
14-1/2"
14''
AMIGA™, Left Hand
AMIGA™ WITH INTEGRAL SKIRT,
Left Hand
*72''
Motor
*72"
*60"
17-3/8''
24"
13-1/2" x 4"
15-5/8"
16'' x 4''
10" x 4"
32"
48"
36''
Motor
Motor
2''
14-1/2''
11-1/8''
5-11/16"
2"
9-3/8"
8-1/2"
2"
13-3/4"
(Left-hand only as shown)
Opt. Service Access
AMIGA™ WITH INTEGRAL SKIRT,
CETRA™ W/INTEGRAL SKIRT, Left Hand
Right Hand
BIANCA™
*60"
*60"
*60"
15-5/8"
10" x 4"
12" x 4"
12" x 4"
32"
32"
32"
Motor
Motor
Motor
16"
16"
2"
9-3/8"
5-11/16"
2"
5-3/4"
5-3/4"
2"
Opt. Service Access
Opt. Service Access
CETRA™ W/INTEGRAL SKIRT, Right Hand
9"
9"
CETRA™ 532, Left Hand
CETRA™ 532, Right Hand
*60"
*60"
*60"
12" x 4"
12" x 4"
17-3/8"
12" x 4"
36"
Motor
36"
36"
Motor
Motor
18"
18"
5-3/4"
2"
5-3/4"
2"
Opt. Service Access
Opt. Service Access
9"
5-3/4"
2"
9"
CETRA™ 536, Right Hand
*60"
CETRA™ 536, Left Hand
9"
CETRA™ 536 WITH INTEGRAL SKIRT, Left Hand
*60"
8-1/4"
*60"
17-3/8"
5-3/4"
8-1/4"
12" x 4"
16"
32"
12" x 5"
36"
16"
Motor
15" x 5"
Motor
32"
2-1/2"
5-1/4"
Motor
2-1/2"
2-1/2"
LUXURA™ 5, Left Hand
Opt. Service Access
2"
2-1/2"
5-1/4"
9"
CETRA™ 536 WITH INTEGRAL SKIRT, Right Hand
Opt. Service Access
LUXURA™ 5, Right Hand
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
10
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (RECTANGULAR)
*66"
*60"
*60"
8-3/8"
8-1/4"
8-1/4"
15-3/8"
15-3/8"
12" x 5"
17"
12" x 5"
12" x 5"
32"
32"
34"
Motor
Motor
Motor
2-1/2"
5-1/4"
2-1/2"
5-1/4"
2-1/2"
5-3/8"
2-1/2"
2-1/2"
2-1/2"
Opt. Service Access
LUXURA™ 5 WITH INTEGRAL SKIRT, Right Hand
LUXURA™ 5 WITH INTEGRAL SKIRT, Left Hand
LUXURA™ 5.5, Left Hand
*66"
*60"
*60"
8-3/8"
9-1/4"
9-1/4"
14-3/8"
17"
14-3/8"
12" x 5"
12" x 5"
12" x 5"
30"
30"
34"
2-1/2"
Motor
Motor
Motor
2-1/2"
2-1/2"
5-7/8"
2-1/2"
5-7/8"
2-1/2"
2-1/2"
5-3/8"
Opt. Service Access
LUXURA™ 530 WITH INTEGRAL SKIRT, Right Hand
LUXURA™ 530 WITH INTEGRAL SKIRT, Left Hand
LUXURA™ 5.5, Right Hand
*60"
8-3/4"
*60"
8-3/4"
*72"
2"
10-1/2"
2"
2"
21"
42"
21"
10" x 4"
21"
12" x 4"
42"
10" x 4"
Motor
42"
Motor
Motor
4-3/8"
Opt. Service Access
4-3/8"
4-3/8"
Opt. Service Access
Opt. Service Access
MAJORA™ 5, Left Hand
MAJORA™ 6, Left Hand
MAJORA™ 5, Right Hand
*72"
2"
*72"
*72"
10-1/2"
8-1/2"
2"
8-1/2"
2"
21"
42"
20-1/2"
12" x 4"
20-1/2"
12" x 4"
12" x 4"
42"
42"
Motor
Motor
Motor
4-3/8"
4-3/8"
Opt. Service Access
4-3/8"
MAJORA™ 6 W/INTEGRAL SKIRT, Left Hand
MAJORA™ 6, Right Hand
MAJORA™ 6 W/INTEGRAL SKIRT, Right Hand
Opt. Service
Access
Opt. Service
Access
Opt. Service
Access
12" H x 18" L
Service Access
12" H x 18" L
Service Access
*60"
12" H x 18" L
Service Access
*60"
*72"
10" x 4"
2"
10" x 4"
2"
10" x 4"
42"
42"
42"
Motor
Motor
2"
Motor
11-7/8"
11-7/8"
11-7/8"
30"
MITO™ 5, Left Hand
5-3/8"
5-3/8"
30"
MITO™ 5, Right Hand
5-3/8"
36"
MITO™ 6, Left Hand
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
11
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (RECTANGULAR)
12" H x 18" L
Service Access
12" H x 18" L
Service Access
Opt. Service
Access
*60"
*60"
12" H x 18" L
*72"
Service Access
21"
21"
11" x 4"
11" x 4"
10" x 4"
42"
42"
42"
Motor
Motor
2"
Motor
11-7/8"
5-3/8''
5-3/8''
8-1/2''
Opt. Service Access
Opt. Service Access
2''
2''
5-3/8"
36"
MITO™ 6, Right Hand
8-1/2''
NOVA™ 5, Right Hand
NOVA™ 5, Left Hand
12" H x 18" L
Service Access
12" H x 18" L
Service Access
*60"
*60"
*60"
21"
21"
21"
11" x 4"
11" x 4"
11" x 4"
42"
42"
42"
Motor
Motor
Motor
5-1/4''
7''
Opt. Service Access
7''
2''
Opt. Service Access
2''
2''
9-1/4"
8-1/2''
8-1/2''
NOVA™ 5 WITH INTEGRAL SKIRT, Left Hand
NOVA™ 5 W/3-SIDED TILE FLANGE, Left Hand
NOVA™ 5 W/3-SIDED TILE FLANGE, Right Hand
*60"
*60"
*60"
21"
18"
11" x 4"
18"
10" x 4"
10" x 4"
42"
36"
36"
Motor
Motor
Motor
5-1/4''
4-5/8"
4-5/8"
Opt. Service Access
2"
Opt. Service Access
2"
2''
9"
9"
9-1/4"
NOVA™ 536, Right Hand
NOVA™ 536, Left Hand
NOVA™ 5 WITH INTEGRAL SKIRT, Right Hand
*72"
*60"
*60"
21"
18"
18"
14" x 4"
10" x 4"
10" x 4"
36"
42"
36"
Motor
Motor
Motor
6-7/8"
8-1/2"
4-5/8"
9"
2"
4-5/8"
9"
Opt. Service Access
2"
2"
NOVA™ 6, Left Hand
NOVA™ 536 W/INTEGRAL SKIRT, Right Hand
NOVA™ 536 W/INTEGRAL SKIRT, Left Hand
*72"
*72"
*72"
9-3/8"
9-3/8"
21"
17-7/8"
10" x 4"
14" x 4"
17-7/8"
6-7/8"
10" x 4"
42"
36"
36"
Motor
Motor
Motor
2"
2"
6-7/8"
8-1/2"
6-7/8"
2"
NOVA™ 6, Right Hand
Opt. Service Access
NOVA™ 636 W/INTEGRAL SKIRT, Left Hand
NOVA™ 636 W/INTEGRAL SKIRT, Right Hand
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
12
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (RECTANGULAR)
*60"
*60"
*60"
42"
13" x 5"
42"
42"
12"
13" x 5"
13" x 5"
Motor
Motor
Motor
12"
12"
Opt.
Service
Access
4-1/4"
Opt.
Service
Access
4-1/4"
Opt.
Service
Access
5"
4-1/4"
30"
5"
30"
5"
30"
SIGNA™ 5 W/3-SIDED TILE FLANGE, Left Hand
SIGNA™ 5, Left Hand
SIGNA™ 5, Right Hand
*60"
*60"
*72"
13" x 5"
18-1/2" x 5"
42"
16" x 5"
42"
42"
Motor
12"
Motor
Motor
12-3/4"
4-1/4"
Opt.
Service
Access
11-1/4"
12-1/2"
4-1/4"
30"
(Right hand only as shown)
5"
30"
5"
Opt.
Service
Access
36"
6-3/4"
SIGNA™ 5 W/3-SIDED TILE FLANGE, Right Hand
SIGNA™ 6, Left Hand
SIGNA™ 5 W/INTEGRAL SKIRT
*72"
18-1/2" x 5"
42"
Motor
11-1/4"
12-1/2"
5"
Opt.
Service
Access
36"
SIGNA™ 6, Right Hand
*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
13
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (OVAL)
NOTE: These units have been provided with cutout templates included in shipping carton.
See CUTOUT information for each model on page 8.
12" x 4"
12" x 4"
42"
2"
42"
Motor
Motor
2"
35-3/4"
35-3/4"
12" H x 18" L
Service Access
71-1/2"
12" H x 18" L
Service Access
71-1/2"
FRESCO™, Left Hand
FRESCO™, Right Hand
62"
62"
21-1/2"
21-1/2"
12" x 4"
12" x 4"
43"
43"
Motor
Motor
5"
9-1/2"
5"
9-1/2"
2"
12" H x 18" L
Service Access
12" H x 18" L
Service Access
2"
GALLERY™ 5 OVAL, Right Hand
GALLERY™ 5 OVAL, Left Hand
72"
72"
21"
14" x 4"
21"
14" x 4"
42"
Motor
42"
Motor
12" H x 18" L
Service Access
6-7/8"
2"
12" H x 18" L
Service Access
6-7/8"
2"
11-1/2"
11-1/2"
GALLERY™ 6, Right Hand
GALLERY™ 6, Left Hand
2"
2"
12-1/2"
12-1/2"
21"
14" x 4"
14" x 4"
42"
42"
Motor
Motor
21"
72"
72"
GALLERY 6 UNDERMOUNT, Right Hand
GALLERY 6 UNDERMOUNT, Left Hand
71-1/2"
2"
71-1/2"
72"
11"
11"
20"
2"
12" x 4"
20"
40"
12" x 4"
13" X 6"
3"
Motor
Motor
40"
Motor
42"
11"
5"
5"
MILANO™, Left Hand
36"
MILANO™, Right Hand
(Right-hand only)
LUNA™
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
14
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (OVAL)
NOTE: These units have been provided with cutout templates included in shipping carton.
See CUTOUT information for each model on page 8.
72"
72"
32"
32"
12"
13" X 4"
13" X 4"
44"
44"
3"
3"
12"
Motor
Motor
4-11/16"
36"
12" H x 18" L
Service Access
12" H x 18" L
Service Access
4-11/16"
36"
4"
4"
OPALIA™, Right Hand
OPALIA™, Left Hand
62"
62"
21-1/2"
21-1/2"
12" x 4"
12" x 4"
43"
43"
Motor
Motor
5"
5"
12" H x 18" L
Service Access
9-1/2"
12" H x 18" L
Service Access
9-1/2"
2"
2"
RIVA™ 5, Left Hand
RIVA™ 5, Right Hand
72"
72"
21"
21"
14" x 4"
14" x 4"
42"
42"
Motor
Motor
6-7/8"
6-7/8"
2"
2"
11-1/2"
12" H x 18" L
Service Access
12" H x 18" L
Service Access
11-1/2"
RIVA™ 6, Right Hand
RIVA™ 6, Left Hand
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
15
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (CORNER)
55"
32-1/4"
33-13/16"
60"
12" H x 18" L
Service Access
Opt.
Service
Access
55"
55"
60"
55"
Motor
Motor
Opt.
Service
Access
12" x 4"
Motor
Service
Access
16" X 4"
14" X 4"
27"
"
27"
26"
26"
29-3/8"
25-1/4"
36 1/2"
36 1/2"
32-1/2"
43-7/8"
25-1/4
33-13/16"
6"
39 1/2"
9-7/8"
40-7/16"
- Junction Box
49"
- Junction Box
44 1/2"
41-9/16"
- 2" x 4" Stud
(Right-hand only as shown)
(Right-hand only as shown)
(Right-hand only as shown)
CAPELLA™ SPACESAVER
CAPELLA™ 55
CAPELLA™ 55 WITH INTEGRAL SKIRT
Opt.
Service
Access
33-1/2"
33-1/2"
33-1/2"
Opt.
60"
Service
Access
60"
60"
60"
60"
60"
61-1/2"
Ref.
Motor
Motor
14" X 4"
Service
Access
14" X 4"
12" H x 18" L
Service
14" X 4"
Access
27"
34-15/16"
27"
27"
27"
34-15/16"
27"
27"
6"
6"
34-15/16"
12" H x 18" L
Service Access
43-1/8"
46-5/8"
6"
46-5/8"
43-1/8"
46-5/8"
43-1/8"
CAPELLA 60 w/FRONT LEFT MOTOR/PUMP,
Left Hand
CAPELLA™ 60, Right Hand
CAPELLA™ 60, Left Hand
33-1/2"
34"
34"
Opt.
Service
Access
Opt.
60"
60"
60"
Service
Access
60"
60"
60"
Motor
19" X 4"
19" X 4"
Service
Access
Service
Access
Motor
14" X 4"
7-1/2"
Motor
7-1/2"
27"
34-15/16"
24"
24"
27"
24"
34"
24"
34"
50-1/4"
13"
6"
46-5/8"
50-1/4"
13"
43-1/8"
47-3/4"
47-3/4"
- Junction Box
(Right-hand only as shown)
CAPELLA™ 60 WITH INTEGRAL SKIRT
GALLERY™ CORNER, Left Hand
GALLERY™ CORNER, Right Hand
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
16
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN
ROUGHING-IN REFERENCE (CORNER)
Opt.
Opt.
Service
Access
Service
Access
60"
60"
60"
60"
60"
60"
Service
Access
Motor
Motor
Motor
14" x 4"
Service
Access
14" x 4"
14" x 4"
27-1/4"
35"
27-1/4"
35"
27-1/4"
27-1/4"
35"
27-1/4"
46"
27-1/4"
35"
44"
35"
44"
46"
46"
35"
44"
- 2" x 4" Stud
- 2" x 4" Stud
- 2" x 4" Stud
- Junction Box
TARA™, Left Hand
TARA™, Right Hand
(Right-hand only as shown)
TARA™ WITH INTEGRAL SKIRT
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. Not all export units come with pre-installed Pump/Motor.
CUTOUT
CUTOUT- CORNER BATHS
3" RADIUS
CORNERS
(5 PLACES)
58"
58"
(1473 mm)
(1473 mm)
59"
58"
58"
Ref.
(1473 mm)
(1473 mm)
Drain
57"
Ref.
Overflow
90˚
25-1/2"
90˚
Motor
Drain
25-1/2"
(648 mm)
Overflow
90˚
90˚
(648 mm)
22-5/8
(575 mm)
"
45-9/16"
(1157 mm)
"
22-5/8
50"
(1270 mm)
CAPELLA 60 &
CAPELLA 60 W/ FRONT LEFT MOTOR/PUMP
(Motor/Pump position not shown.)
(575 mm)
GALLERY CORNER,
Left Hand
3" RADIUS
CORNERS
(5 PLACES)
58"
(1473 mm)
58"
(1473 mm)
59"
Ref.
58"
(1473 mm)
58"
(1473 mm)
Motor
Drain
57"
Ref.
90˚
Overflow
90˚
Motor
Drain
Overflow
25-1/2"
(648 mm)
25-1/2"
(648 mm)
90˚
90˚
22-5/8
(575 m
45-9/16"
(1157 mm)
"
22-5/8"
(575 mm)
50"
m
)
TARA CORNER CUTOUT
Right Hand
(1270 mm)
GALLERY CORNER,
Right Hand
58"
(1473 mm)
58"
(1473 mm)
59"
Ref.
Motor
Drain
Overflow
90˚
90˚
25-1/2"
(648 mm)
25-1/2"
(648 mm)
45-9/16"
(1157 mm)
TARA CORNER CUTOUT
Left Hand
17
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Framing and Support
The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor.
The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to the table under total
weight for your model. The unit must be supported from the bottom of the bath and not from the bath rim or tile flange. If the subfloor is level
and a continuous surface, no other preparation is necessary. You can proceed to install the bath. If the subfloor is not level, you MUST level the
entire surface prior to installing the bath. The use of materials that provide a level installation are allowed provided the method used will insure
a level bath that is supported from the bottom. Materials that may be used are a floor leveling compound, mortar, plaster or minimal expansion
structural foam having a density of a minimum of 5 lbs./cubic ft.; however the bath must remain level in order for it to drain properly and all foam
feet must make full contact with the leveling material. Both sides of a joint or splice of subfloor should be level to each other. When attaching
baths with flanges to stud wall, use shims to fill any gaps between the bath flange and studs.
The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added weight must be fully self-
supporting.
The protective film liner inside the bath is used to prevent damage to the finish during installation. Before installation, remove
liner to inspect for any defects, reapply and do not remove until final cleanup.
Important: If a skirt is to be used, it must be installed at the time of unit installation – refer to skirt installation instructions. Install
optional trim parts when all installation has been completed.
TYPICAL INSTALLATIONS
MORTAR OR ADHESIVE
TILE
FINISHING
MATERIAL
MORTAR OR ADHESIVE
TILE
SEALANT
MORTAR
PLASTER
FILLER
SEALANT
CEMENT
BOARD
FLASHING
BATH RIM
FLANGE
NAIL
OR
SCREW
SUB-FLOOR
FLASHING
SILICONE
SEALANT
STUD
WALL
1" X 4" (NOT FOR
SUPPORT)
1" X 4" (NOT FOR SUPPORT)
1" X 4" (NOT FOR SUPPORT)
FLUSH TO WALL
OPTIONAL TILE FLANGE KIT
SEMI-SUNKEN
NOTE: ON the Riva 5 and Riva 6, the discharge plumbing extends slightly beyond the bath rim. When installing either bath as semi-
sunken, lower the pump/motor side in first into the cutout.
TYPICAL FLANGE MOUNTING DETAIL
TILE
TILE
STUD
CAULKING
STUD
CAULKING
CEMENT
BOARD
CEMENT
BOARD
TILE
ADHESIVE
TILE
ADHESIVE
FLANGE
FLANGE
ATTACH WITH
SCREWS
PROVIDED
ATTACH WITH
SCREWS
PROVIDED
SHIM IF
SHIM IF
NECESSARY
TO FILL GAPS
BETWEEN
STUD
NECESSARY
TO FILL GAPS
BETWEEN
STUD
STUD
STUD
1/8" GAP
1/8" GAP
FLANGE
AND FLANGE
AND FLANGE
1"X 4"
(NOT FOR
SUPPORT)
FLANGE
UNDERMOUNT INSTALLATION OPTIONS
The undermount gives the opportunity to be flexible in the design and location of the bath. Examples are shown for possible
installations. Refer to pages 23-24 for undermount installation instructions.
CORNER
FREE STANDING
18
NICHE
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Skirts
INTEGRAL SKIRT MOUNTING DETAIL
Corner Baths with Skirt
If an optional skirt is used on a corner bath, additional support is
necessary in the front of the unit. Measure the height from the floor
to the underside of the bath rim. Cut two 2" x 4" studs, apply adhe-
sive to both ends and install (See specifications in ROUGHING-IN
REFERENCE (CORNER)).
FINISHING
MATERIALS
CAULKING BEAD
SUPPORT FOR CORNER BATHS
APPLY
ADHESIVE
H
SKIRT
PANEL
2" x 4" STUD
(50,8 mm x 101,6 mm)
Removable Skirt Panel
Removal and Installation
U FRAME SKIRT MOUNTING DETAIL
To remove panel, grab a top corner of access panel and pull outward
to release the first Dual Lock fastener. Then work around the
perimeter pulling access panel outward to release the remaining
dual Lock fasteners.
To reinstall, align access panel such that the Dual Lock fasteners
on the access panel match to the Dual Lock fasteners on the tub
skirt. Engage each Dual Lock pair until all are snapped into place.
FINISHING MATERIALS
SECURE SHELLCLIP
UNDER CENTER
BATH RIM
FILLER (Optional)
CAULKING
BEAD
SKIRT
PANEL
SKIRT
FRAME
SECURE BOTTOM OF FRAME TO FLOOR
PEEL BACK CORNER
TO BEGIN DISCONNECTING
DUAL LOCK™ FASTENER
19
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Service Access
Service Access with Integral Skirt
Service access is through the removable skirt panels.
For partially or fully sunken installations, allow for access to ser-
vice connections. It is the installer's responsibility to provide suffi-
cient service access. The recommended minimum dimensions al-
lowable for service to the bath are shown in the "Service Access"
illustration and on the ROUGH-IN drawing for that tub.
Provide adequate area around unit for air circulation for cooling
the motor and to supply sufficient air to the jets. Do not insulate this
area or around motor.
SERVICE ACCESS (WITH INTEGRAL SKIRT)
Optional RapidHeatTM Service Access
Where tubs have been ordered with the optional RapidHeatTM
heater consider an additional service access.
If service access has not been provided, it is the home owners
responsibility to remove the bath and provide the required
access, should a repair become necessary.
REMOVABLE SKIRT
ACCESS PANELS
MOTOR
ACCESS AREA
Service Access with Skirt
An optional skirt fits along the side of the bath for above-floor
installations and is also an access panel for servicing. Allow a space
of at least 8 inches away from the bath for skirt removal.
The skirt is designed to accommodate the added height of the
tile, linoleum, or other floor coverings up to 1-1/4" (31,75 mm) above
the floor, and will be flush with the floor when installed.
More detailed instructions on skirt installation are provided with
the optional skirt assembly.
SERVICE ACCESS (WITHOUT SKIRT)
MOTOR
12"
(30,5 cm)
FRONT
SERVICE ACCESS (CORNER BATHS)
18"
(45,7 cm)
12"
(30,5 cm)
ALTERNATE
ACCESS
PREFERRED
ACCESS
18"
(45,7 cm)
20"
(50,8 cm)
B
18"
(45,7 cm)
In some cases, access may not have been provided because of
the design of the bath environment and having full understanding
that in this case, it may be necessary to remove the unit for service.
If this is the case, diagnosing a problem may not be possible
without complete access to the plumbing system. This would ne-
cessitate the removal of the unit. Although this practice is not com-
monly implemented, it is an acceptable method.
C
A
36"
(91,4 cm)
24"
(60 cm)
RIGHT HAND UNIT SHOWN
A - Preferred access
B - Acceptable alternative if access A is not possible
C - Additional access for equipment (Optional)
NOTE: Left hand unit access is on the opposite
side (mirror Image).
SERVICE ACCESS
(BG55, CAPELLA 60 FRONT LEFT MOTOR CORNER BATH ONLY)
AREA
A
FRONT
AREA
B
MOTOR
In some cases access may have been provided in Area A but
service is required in Area B which requires the unit to be pulled for
service and reinstalled.
12"
(30,5 cm)
If service access has not been provided, it is the homeowner's
responsibility to remove the bath and provide the required
access, should a repair become necessary.
18"
(45,7 cm)
Preferred access area
20
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
ELECTRICAL CONNECTION (FOR CORNER BATHS)
Electrical Connections
A separate circuit, which must be protected by a Ground
Fault Circuit Interrupter (GFCI), is required. Install a duplex
outlet to the studwall underneath the bathtub, at least 4" (10,6
cm) above the floor. The duplex outlet is not provided. Be-
cause these units are manufactured with a safe, convenient
electronic control whirlpool ON/OFF switch on the bath itself,
no remote switch or timer is necessary.
3 PRONG
PLUG FROM
MOTOR POWER CORD
TO CONTROL BOX
CONTROL BOX
DUPLEX GFCI
RECEPT.*
4" (10,6 cm) MIN.
OR IN
ACCORDANCE
WITH LOCAL
BUILDING OR
ELECTRICAL
CODES
DANGER: RISK OF ELECTRIC SHOCK. Connect only to
a circuit protected by a Ground Fault Circuit Interrupter
(GFCI).
CAUTION: Operating the motor/pump without enough
water in the bath can cause leaking and permanent dam-
age to the pump. Before power is applied to the installa-
tion, make sure the switch is in the OFF position to avoid
pump damage.
FLOOR
*(NOT PROVIDED)
NOTE: Export units may or may not come with motor/pump or
may come with motor specifications different than what is speci-
fied here. In every case consult with a licensed contractor and
electrician before installing power supply or connecting unit.
Optional RapidHeatTM
Electrical Connection
NOTE: Export units may or may not come with pre-installed
motor/pump or may come with motor specifications different
than what is specified here. In every case consult with a li-
cenced contractor and electrician before installing power sup-
ply or connecting unit.
Jacuzzi Whirlpool Bath makes no claims to the electrical
compatibility or suitability of domestic or export units and is
not responsible for any defects or failures that could have
been discovered, repaired, or avoided by following the appli-
cable building and local electrical codes.
Before installing electrical connection, inspect the heater
nameplate and determine if you have a 120 VAC or a 240
VAC whirlpool unit (240 VAC unit not available in U.S.A.).
Install a separate 120 VAC 15 AMP or 240 VAC 15 AMP
dedicated circuit with GFCI protection. With a #8 solid cop-
per wire, bond the heater to the house electrical panel or
approved local bond. Abonding lug is provided on the heater.
At initial start-up and before each use thereafter with power
ON, push the GFCI test button. The reset button should pop
out. Push this button in to reset. If the interrupter fails to
operate in this manner, there is a ground current flowing or a
device malfunction, indicating the possibility of electrical
shock. Turn OFF power and do not use the bath until the
source of the problem has been identified and corrected.
On the Capella 55 with integral skirt, Capella 60 with inte-
gral skirt, Capella Spacesaver with integral skirt and Tara with
integral skirt a duplex junction box has been provided. To
access, remove skirt access panel. See top views in ROUGH-
IN section for location.
A separate GFCI protected outlet (not provided) is required
for pump/motor and is to be installed in the junction box. The
junction box is to be hard wired. The motor is bonded to the
junction box at the factory.
CAPELLA 55 with skirt, CAPELLA 60 with skirt,
CAPELLA SPACESAVER with skirt, &
TARA with skirt - JUNCTION BOX
BONDING TO PUMP/MOTOR
ELECTRICAL CONNECTION RAPIDHEAT™
GFCI
(NOT
PROVIDED)
POWER CORD FROM
CONTROL BOX
POWER CORD
TO MOTOR
J-BOX PROVIDED
ELECTRICAL CONNECTION
(FOR SIDE/END DRAIN BATHS)
3 PRONG
PLUG FROM
CONTROL BOX
DUPLEX GFCI
RECEPT.*
INSTALL SEPARATE
M
T
GFCI PROTECTED CIRCUITS
4" (10,6 cm) MIN.
OR IN
ACCORDANCE
WITH LOCAL
BUILDING OR
ELECTRICAL
CODES
HEATER
FLOOR
*(NOT PROVIDED)
21
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Plumbing and Water Supply
Drain Information
A drain/overflow assembly (sold separately) must be installed on the bath, water tested, and connected to the sanitary
system of the house. After opening the carton, inspect for damage and verify that the kit is of the proper finish. In the Jacuzzi
Whirlpool Bath drain/overflow kit, note that the waste flange, strainer, overflow cover and cover screws are packaged in a
separate package within the kit to protect the trim finish. Follow the installation instructions provided with your drain/overflow
kit. After the drain is fully installed, test for proper drainage. If the unit does not drain properly, rectify this condition before
proceeding with the installation. Jacuzzi Whirlpool Bath is not responsible for removal and or reinstallation costs.
NOTE: Watertight installation of the drain is the installer's responsibility. Drain leakage is excluded from the Jacuzzi
Whirlpool Bath warranty of this product.
Plumbing
Pump, jets, and suction fittings for the whirlpool system are factory plumbed in Schedule 40 PVC piping.
All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping. If
leaks are detected, notify Jacuzzi Whirlpool Bath. Do not install the unit.
Water Supply
Consult local authorities for plumbing code requirements in your area.
IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the
installer. Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping, fill systems, or
drain/overflow systems. Nor is it responsible for damage to the bath which occurs during installation.
CAUTION: A nonflammable protective barrier must be placed between soldering work and bath unit to prevent damage
to the bath.
Clean-Up After Installation
To avoid dulling and scratching the surface of the bath, never use abrasive cleaners. A mild liquid detergent and warm water
will clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools will scratch the surface. Spots left by plaster or grout can be
removed if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult surface stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol).
NOTE: Use these chemicals only on SURFACE stains.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper.
You can restore the glossy finish to the acrylic surface of the bath with a special compound, Meguiar's #10 Mirror Glaze. If that
is not available, use automotive rubbing compound followed by an application of automotive paste wax.
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Ask your Jacuzzi Whirlpool Bath
dealer for special instructions or visit our web site at http://www.jacuzzi.com/. To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
22
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
UNDERMOUNT INSTALLATION INSTRUCTIONS
COUNTER
Installation
A typical installation will have these construction character-
istics.
ALL FOAM FEET MUST BE IN CONTACT WITH LEVEL FLOOR
Unit Protection
If protective film has been removed, reapply film. For added protection, place a drop cloth or other material in the bottom of bath
for protection. Be careful not to scratch the bath surface.
Counter Preparation
NOTE: On pump/motor side of bath, the counter should extend a minimum of 4" (10,2 cm) past the outer edge of bath, in order
to clear the pump/motor plumbing extending beyond the rim of the bath.
MOTOR/PUMP
INSIDE EDGE
COUNTER
OF RIM
Position the template so that the cutout oval aligns with the
STUD WALL
rim edge.
TEMPLATE
B
A
C
BATH RIM
In this position, using a grease pencil, mark on the bath the
center line positions through the cut out slots. Remove
template. Measure from marked center lines to a fixed point
such as a wall.
D
MEASURE FROM
CENTERLINE
MARKS TO WALL
Transfer these measurements to counter and mark center lines positions. Position template and cut counter for the desired offset.
B
A
COUNTER
C
COUNTER
BATH RIM
TEMPLATE
BATH RIM
D
OFFSET
COUNTER
After cutting is complete, perform any needed routing, edge work or polishing to the counter.
23
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
UNDERMOUNT INSTALLATION INSTRUCTIONS
COUNTER
Position the counter on top of the bath to ensure correct fit and
appearance. Make any adjustments that may be necessary.
Remove the counter.
BATH
Adhering Counter to Bath
APPLY SILICONE
SEALANT TO TOP
OF BATH RIM
Clean any dirt or debris from the bath rim. Do not use abrasive
cleaners.
Where the counter will make contact with top of the bath rim,
apply a bead of silicone sealant.
CAUTION: Do not use an adhesive or adhesive sealant to
secure the counter to the bath rim. If maintenance or
remodelling is required the counter may have to be
removed. Adhesive will permanently bond the counter to
the bath. This will make removal difficult and costly and
may cause damage to the counter or bath.
COUNTER
Carefully position the counter onto the bath rim. The counter
will need to be held in place while the sealant cures. Follow
the manufacturer's instructions to determine time required for
curing.
BATH
Apply a continuous bead of silicone sealant around the entire
seam between the counter and bath rim. Allow sealant to skin
over or cure before cleaning the counter or bath.
APPLY SILICONE SEALANT
WEIGHTS
24
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Operation
NOTE: These instructions pertain to all Builder/Comfort bath products manufactured by Jacuzzi Whirlpool Bath. Not all features
discussed in this instruction booklet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained after each use
and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools
or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas
available.
Once the bath is installed, remove any residue or foreign materials left over from construction. Paint, tar, or other difficult surface stains can
be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). NOTE: Use these chemicals only on SURFACE stains. Other dirt
can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or plastic edge; do not use metal scrapers,
wire brushes or other metal tools, as they will damage the bath's surface.
Water Level
Close the drain and fill the bath until water is at least 1" to 2" (25,4 mm - 50,8 mm) above the highest jet (see water line indicated in the
illustration). Do not turn on the whirlpool system at any time if the jets are not completely immersed in water. Do not immerse the
control panel by overfilling the bath. Running the whirlpool system when there is insufficient water in the bath could result in water spraying
outside the bath area. Running the whirlpool system without water will damage the recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop below the jets which could result in water being sprayed out of the unit. To prevent
this, you must turn unit off before exiting bath.
Jacuzzi builder/comfort units come equipped with electronic con-
trols. Refer to the Electronic Controls instructions on the next page.
FILL TO AT LEAST
1" - 2" (25,4 mm - 50,8 mm)
TYPICAL BATH FITTINGS
ABOVE HIGHEST JET
ELECTRONIC
CONTROL
SWITCH
1" - 2"
FULLY ADJUSTABLE JETS
SUCTION
COVER
WATER RAINBOW
FILL SPOUT (OPTIONAL)
DRAIN/OVERFLOW
(OPTIONAL)
(Optional) RapidHeatTM
Operation
Once the heater is installed and the whirlpool pump is operating,
the heating function is totally automatic. The heater will help main-
tain the temperature of the water in the bath.
Export units come equipped with the Magic Touch® Whirlpool ON/
OFF switch. Refer to the Magic Touch® Whirlpool Switch instructions
on the next page.
TYPICAL BATH FITTINGS
Vacuum or Pressure Switch
MAGIC TOUCH WHIRLPOOL
ON/OFF SWITCH
The heater is equipped with a preset vacuum switch or pressure
switch which will not allow the heater to turn ON if the pump is not
running with water flowing through the whirlpool system.
AIR CONTROL
KNOBS
High-Limit Switch
The heater includes an exclusive High-Limit switch. This safety
circuit will not false trip from hot tap water. It will only turn off the
heater if the thermostat fails. To reset, press the button. If the high-
limit trips frequently, contact your Authorized Electrical/Mechanical
find a Service Provider.
FULLY ADJUSTABLE JETS
SUCTION
COVER
HIGH LIMIT RESET
HEATER ON
HEATER ON
OVER HEAT
PROTECTION
WATER RAINBOW
FILL SPOUT (OPTIONAL)
PUSH TO RESET
DRAIN/OVERFLOW
(OPTIONAL)
25
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Magic Touch® Whirlpool Switch
Electronic Control Switch
The Magic Touch Whirlpool ON/OFF switch, conveniently located
on the bath, allows you to turn the whirlpool system ON and OFF
while in the bath. Simply push down on the switch button to turn on
the whirlpool system. To turn the system OFF, push down on the
button again.
The Electronic Control ON/OFF Switch, conveniently located on
the bath, allows you to turn the whirlpool system ON and OFF while
in the bath. Simply push down on the switch button to turn ON the
whirlpool system. To turn the system OFF, push down on the button
again.
The Electronic Control Switch will automatically shut OFF after
20 minutes. Push down on the switch button to restart the whirlpool
system again.
WHIRLPOOL ON/OFF SWITCH
L P
O
R
I
O
H
L
W
ON/OFF
DEPRESS CENTER ON/OFF
JETS
Controlling Whirlpool Action
FULLY
ADJUSTABLE
DIRECTIONALLY
ADJUSTABLE
The whirlpool action in your bath is influenced by three factors –
direction of flow, force of water, and force of air. Every bath manufac-
tured by Jacuzzi Whirlpool Bath that is equipped with fully adjustable
PowerPro® jets, are manually adjustable for direction and water force.
Some baths have additional jets which can be adjusted for direction
only.
Direction: To change the direction of the water flow, swivel the
jet nozzle to the desired angle. The jets can be directed individually
toward any location on your body to provide a hydromassage. The
jets can also be adjusted so that they all point in the same direction
(clockwise or counterclockwise) to circulate the water in a circular
motion around the bath, causing a total whirlpool effect.
Water Force: The high volume, fully adjustable jets can be ad-
justed to control the force of the water coming into the bath. For
robust action, increase the force of the flow by rotating the jet handles
to the left (counterclockwise). For a more gentle effect, rotate the
handles to the right (clockwise). Never run the whirlpool system
with all the jets closed.
Magic Touch® controls only
AIR INDUCTION CONTROLS
TURN CLOCKWISETO
REDUCE AIR FLOW
TURN COUNTER-CLOCKWISE
TO INCREASE AIR FLOW
Force of Air: The intensity of the hydromassage whirlpool ac-
tion is determined by the air inducted into the water. On the Magic
Touch® control system only: Fully opening the jets allows an equal
amount of air inducted into the water. Decrease the air flow at one
or more jets to increase the air flow for remaining jets. Never run
the whirlpool system with all the jets closed.
26
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE INSTRUCTIONS
Cleaning the Bath
Bath Additives
To clean your bath, simply use a mild, nonabrasive liquid deter-
gent solution. You can protect and restore the gloss to a dulled
acrylic surface by applying an acrylic polish or automotive paste wax.
Never use abrasive household cleaners on any Jacuzzi Whirl-
pool Bath product.
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
Ifyouwanttouseanykindofbathadditive, useonlyasmallamount
of low-foaming powder or crystal substance; the whirlpool action
intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives may
increase the level of accumulations of bath residue in the whirlpool
system. If excess accumulations persist, you should discontinue use
of these products.
Repairs to the Surface
Major scratches and gouges which penetrate the acrylic surface
will require refinishing. Contact your Jacuzzi Whirlpool Bath dealer
for special instructions.
Suction Cover/Strainer Maintenance
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT
LEAST TWICE A MONTH
Clean the suction cover/strainer of hair and debris when neces-
sary. To do this, remove the center screw and detach the square
cover. Clean the cover by backflushing debris from the holes. Re-
place the suction cover immediately after cleaning. When reinstall-
ing, orient the cover/strainer with the small notch at the bottom. The
gasket must be inserted into the groove of the cover/strainer before
reinstalling onto the suction fitting.
To remove accumulations of bath residue from the whirlpool
system, it is recommended that a whirlpool bath be purged at least
twice a month. For best results, however, we recommend that you
purge your whirlpool bath after each use using, Systems Clean™, our
exclusive two-part plumbing system cleaner made specifically for
whirlpool baths.
CAUTION: Keep body and hair a minimum of 6 inches (15,2 cm)
away from the suction fitting at all times when the hydromas-
sage system is operating. Hair longer than shoulder length
should be secured close to the head, or a bathing cap should be
worn. Do not operate the hydromassage system with the suc-
tion cover removed! The suction cover is a safety device and
must always be in place on the suction fitting to minimize the
potential hazard of hair and body entrapment.
Systems Clean™ is available through an authorized Jacuzzi
Whirlpool Bath Distributor or by calling us direct at 1-800-288-4002.
Systems Clean™ Instructions for use:
CAUTION: DO NOT USE WHILE BATHING! USE EXTREME
CAUTION WHEN HANDLING THIS PRODUCT!
Immediately after bathing and exiting the whirlpool bath, leave the
bath water in the tub and add more hot water. The water level in the
tub must be at least 2” (50,8 mm) above the highest jet. NOTE:
Inducted air from the hydromassage system will cause the Systems
Clean™ contents to foam and increase odor. If your tub has air
controls, turn OFF the whirlpool air control or turn it to the lowest
setting and pour in the entire contents of PACKET #1 ONLY directly
into the bath water. For best results, pour the System Clean into the
tub near the intake for the circulation pump and be sure to avoid
contact with your skin. Allow the whirlpool to run for 30 seconds and
then add PACKET #2 ONLY. It is important to use PACKET #1
before PACKET #2 to avoid a strong odor. Allow the bath to run for
5 to 10 minutes then drain the tub completely. Refill the tub with cold
water and run for 2 to 3 minutes. Drain completely and rinse off any
residue.
SUCTION COVER/STRAINER ASSEMBLY
COVER STRAINER
SUCTION
FITTING
SCREW
GASKET
NOTCH
DANGER: Harmful if swallowed. Eye irritant. Protect your eyes,
skin and mucus membranes from contact with this product or its
concentrated solution. A strong alkaline product can cause
severe burns to the eyes and skin.
If you have followed the standard purging instructions above and
still have an excess accumulation of bath residue and desire an
alternative cleaning mechanism, we recommend SUPER SYSTEMS
CLEAN™ PLUS manufactured by Stearns Packaging to rectify this
condition. This may be obtained by contacting us at 1-800-288-4002.
It is recommended that you follow the instructions provided by the
manufacturer with the product. Repeated use may be necessary.
SUPER SYSTEMS CLEAN™ PLUS does not replace the necessity
to regularly purge your whirlpool system with Systems Clean™ as
recommended.
27
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
General Whirlpool Bath Troubleshooting Guide
PROBLEM
PROBABLE CAUSES
REMEDY
Reset GFCI.
Pump/Motor does not start.
No power to pump/motor.
Insert plug(s) fully into outlet(s). Units
with electronic controls: Motor plugs into
control box and control box plugs into
GFCI receptacle. Units with manual
controls: Motor plugs into GFCI recep-
tacle.
Pump/motor not plugged in.
Reconnect tube to Magic Touch switch
or to air switch pump/motor.
Magic Touch switch - air tube not
connected to switch or to air switch
on pump/motor.
Replace pump/motor assembly.
Pump/motor faulty.
Open jets by rotating counterclockwise.
Pump/Motor operates but no fully
adjustable jets are functioning.
Jets are closed.
With motor turned off, remove safety
cover and remove any debris. Replace
suction cover before operating.
Suction cover may be clogged.
Open air control valves.
Pump/Motor operates but air is not
injected into water.
Air valves closed.
Reconnect tube to Magic Touch switch
or to air switch pump/motor.
Pump/motor does not shutoff.
Magic Touch switch - air tube not
connected to switch or to air switch
on pump/motor.
Reconnect motor power cord to control
box.
Motor power cord not connected to
control box.
Replace timer.
If a wall timer is used, the timer is
defective
Untighten unions check and reseat O-
ring. If O-ring has been pinched out of
shape, replace (refer to Service Support
number below). When tightening union
nuts, hand tighten only.
Water leakage from pump unions.
Overtightened, O-ring may be
pinched or improperly seated, under
tightened.
Let motor cool; thermal protection will
reset. Check for proper ventilation.
(Check supply voltage.)
Pump/motor shuts off by itself or with
wall timer, before set time elapses.
Motor thermal protection has
deactivated pump/motor due to
overheating. (Supply voltage low.)
Reset GFCI. If it continues to trip do not
use this unit. Disconnect the unit and
have the problem corrected by a
GFCI tripped.
licensed electrician before using.
Consult a licensed electrician to correct
wiring to unit.
Inadequate supply wiring.
NOTE: If unit is within the warranty period, contact Jacuzzi Whirlpool Bath Service Support at 1- (800)- 288-4002 with bath's serial
number before work is started. The Serial Number is located on the Specification/Serial Number Plate. See page 30.
28
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Luxury Bath
14525 Monte Vista Ave., CA 91710
Service Support: 1-(800) 288-4002
©2005 Jacuzzi Whirlpool Bath K272000AF 7/06
Printed in the U.S.A.
Printed on Recycled Paper
29
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTHORIZED SERVICE
If you need a referral for a service company near you, or need assistance with operation or maintenance related
questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/
for products and services.
To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
When requesting service or technical assistance please have available both the model and serial number of your
unit. This information can be obtained from the product registration card provided with your unit. If the card has
been misplaced, this information can be obtained from the specification/serial number label on the unit itself (for
location of specification/serial number label see below).
BATH PRODUCTS
Whirlpool baths: The label is located on the wall of the bath near the pump/motor.
Non-jetted baths: The label is located next to the overflow.
SPECIFICATION/SERIAL NUMBER PLATE
CORE NUMBER - SERIAL NUMBER
XXXX - XXXXXX
Applicable Electrical Specifications for your unit.
MODEL # XXXXXXX
NAME XXXXX
COLOR XXXXX
MFG # XXXXX
SER # XXXXXX
ELECTRICAL SPECIFICATIONS
PRINTED IN THIS AREA
YOU WILL FIND YOUR
SERIAL NUMBER HERE.
THIS PRODUCT MEETS OR EXCEED
MADE IN
THE FOLLOWING STANDARDS
USA
BATH & SPA xxxx xxxx.x
SHOWER BASES xxxx xxxx.x
Appropriate Safety Compliance Logos for your unit.
30
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Jacuzzi Whirlpool Bath Limited Warranty
Builder/Comfort Group Bath Product
WARRANTY COVERAGE
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Builder/
Comfort Group Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its sole
option, the unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Builder/Comfort Group Bath products is for two (2) years. Our warranty covers the unit and factory-installed components
(e.g., pump, motor) against defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user.
FIVE YEAR (PARTS ONLY) LIMITED WARRANTY ON PUMP AND MOTOR
Our limited warranty on the pump and motor is for five (5) years for parts only. Warranty coverage begins on the date the unit was originally purchased
by the user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers options
and accessories manufactured by the Company (e.g., fill spout kits, trim kits, skirts) against defects in material or workmanship. Warranty coverage
begins on the date the option or accessory was originally purchased by the user.
WARRANTY LIMITATIONS
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from,
without limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.) including its own negligence; modification of any
type for any reason (including modification to meet local codes); improper installation (including installation not in accordance with instructions and
specifications provided with the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical
modification; misuse; incorrect operation, or lack of proper routine maintenance; operation of the unit without specified minimum amount of water or
at inappropriate water temperature; use of abrasive or improper cleaners; or acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause
(e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool
and/or spa chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company;
the unit's prior usage as an operational display; or defects that should have been discovered before installation. This limited warranty does not include:
labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement unit; any costs
relating to obtaining access for repair; or loss of use damage, including loss of sales, profit or business advantage of any kind under any circumstances.
Bath units are excluded from any warranty coverage if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to
any component).
Warranty coverage is provided in the United States of America and Canada.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO THE
FULLEST EXTENT ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties
applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will
not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized
literature or specifications furnished by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusions may not apply to you.
RETURN OF WARRANTY CARD
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi Whirlpool
Bath in order for this warranty to become effective.
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710
Download from Www.Somanuals.com. All Manuals Search And Download.
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for
ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have been discovered, repaired,
or avoided by proper inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is
delivered. If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier
to respond should be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating
to obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the
responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company
are warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements
at the time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building
codes in U.S.A. or municipal or provincial codes in Canada.
WARRANTY SERVICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are
not agents or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered
by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature
of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that
the failure occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted
to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent.
Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Luxury Bath
Warranty Service Department
14525 Monte Vista Avenue
Chino, CA 91710
Call: 1-(800) 288-4002
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the
Company, call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where
to return, at your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates
the Company's warranty obligation.
©2005 Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIE DE TINAS BUILDER/COMFORT
CONTROLES ELECTRÓNICOS Y MANUALES
MANUAL DE INSTALACIÓN Y OPERACIÓN
Conserve Estas Instrucciones Para Uso Futuro.
Registro del Propietario
Fecha de compra ___________________________________________________________
Comprado a _______________________________________________________________
Instalado por _______________________________________________________________
Número de serie ____________________________________________________________
Número de modelo __________________________________________________________
Instalador: Deje este manual para el propietario.
Propietario: Lea este manual y guardelo para referencia en el futuro.
©2005 Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES IMPORTANTES SEQURIDAD
LÉA Y SIQUE TODAS LAS INSTRUCCIONES
GUARDE ESTAS INSTRUCCIONES
INSTRUCCIONES que PERTENECEN A UN RIESGO DE el FUEGO, DE el
CALAMBRE, O DE la HERIDA A PERSONAS
ADVERTENCIA — CUANDO SE USA ESTA UNIDAD, LAS PRECAUCIONES BÁSICAS SIEMPRE SE
DEBEN SEGUIR, INCLUSIVE LO SIGUIENTE:
PELIGRO — PARAREDUCIR EL RIESGO DE LA HERIDA, NO PERMITE QUE NIÑOS UTILICEN ESTA
UNIDAD A MENOS QUE ELLOS SEAN SUPERVISADOS DE CERCA SIEMPRE.
ADVERTENCIA — UTILIZA ESTA UNIDAD SOLO PARA SU USO DESTINADO DESCRIBIÓ COMO EN
ESTE MANUAL. NO UTILICE LAS FIJACIONES NO RECOMENDADO POR LOS FABRICANTES.
ADVERTENCIA — NUNCA DEJE CAER O METE CUALQUIER OBJETIVO EN ALGUNAAPERTURA.
ADVERTENCIA — NO OPERE ESTA UNIDAD SIN EL GUARDIA SOBRE LA SUCCIÓN QUE QUEDA.
ADVERTENCIA — ESTAUNIDAD DEBE SER CONECTADA SÓLOAUN CIRCUITO DEL SUMINISTRO
QUE ES PROTEGIDO POR UN INTERRUPTOR (GFCI) DE CIRCUITO DE DEFECTO DE SUELO. TAL
GFCI DEBE SER PROPORCIONADO POR EL INSTALADOR Y DEBE SER PROBADO EN UNA BASE
RUTINARIA. PARA PROBAR EL GFCI, EMPUJE EL BOTÓN DE LA PRUEBA. EL GFCI DEBE INTE-
RRUMPIR EL PODER. EMPUJE EL REPONE EL BOTÓN. EL PODER SE DEBE RESTAURAR. SI EL
GFCI FALLA DE OPERAR EN ESTA MANERA, EL GFCI ES DEFECTUOSO. SI EL GFCI INTERRUMPE
EL PODER ALA BAÑERASIN EL BOTÓN DE LA PRUEBAPARA SE EMPUJAR, UNA CORRIENTE DEL
SUELO QUE FLUYE, INDICANDO UNA POSIBILIDAD DE UN CALAMBRE. NO UTILICE ESTA BAÑE-
RADE HYDROMASSAGE. DESCONECTE LABAÑERA DE HYDROMASSAGE Y TENGAEL PROBLE-
MA CORREGIDO POR UN REPRESENTANTE CALIFICADO DEL SERVICIO ANTES DE UTILIZAR.
ADVERTENCIA — (UNIDADES DE CONEXIÓN PERMANENTE) ESTAS UNIDADES CUENTAN CON
UN TERMINAL VERDE (O UN CONECTOR DE CABLE MARCADO CON "G", "GR", "GROUND" O
"GROUNDING") DENTRO DEL COMPARTIMIENTO DE TERMINALES. PARA REDUCIR EL RIESGO
DE DESCARGA ELÉCTRICA, CONECTE EL TERMINAL O EL CONECTOR AL TERMINAL DE TIERRA
DEL SERVICIO ELÉCTRICO O DEL TABLERO DE ALIMENTACIÓN CON UN CONDUCTOR DEL MIS-
MO TAMAÑO DE LOS CONDUCTORES DEL CIRCUITO QUE SUMINISTRAN ESTE EQUIPO.
OPERAR INSTRUCCIONES
ADVERTENCIA — LA INMERSIÓN PROLONGADA EN ELAGUA CALIENTE PUEDE INDUCIR HIPER-
TERMIA. LA HIPERTERMIA OCURRE CUANDO LA TEMPERATURA INTERNA DEL CUERPO ALCAN-
ZA UN PLANOS VARIOS GRADOS ENCIMA DE LATEMPERATURA CORPORAL NORMAL DE 98.6°F.
LOS SÍNTOMAS DE HIPERTERMIA INCLUYEN EL AUMENTO DE UN EN LA TEMPERATURA INTER-
NA DEL CUERPO, EL MAREO, EL LETARGO, SOMNOLENCIA Y DESMAYAR. LOS EFECTOS DE
HIPERTERMIA INCLUYEN:
A) EL FRACASO PARA PERCIBIR EL CALOR,
B) EL FRACASO PARA RECONOCER LA NECESIDAD DE SALIR EL BALNEARIO O LA JACUZZI,
C) DESCONOCIMIENTO DEL PELIGRO INMINENTE,
D) EL DAÑO FETAL EN MUJERES ENCINTAS,
E) LA INCAPACIDAD FÍSICA SALIR EL BALNEARIO O EL JACUZZI, Y
F) LA INCONSCIENCIA QUE TIENE COMO RESULTADO EL PELIGRO DE AHOGAR.
ADVERTENCIA — EL USO DE ALCOHOL, LAS DROGAS O LA MEDICINA PUEDEN AUMENTAR MU-
CHO EL RIESGO DE HIPERTERMIA FATAL.
ADVERTENCIA— NO MANIPULACON CONTROLES USUARIO-OPERADOS NI TALES DISPOSITIVOS.
2
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES
ADVERTENCIA — LOS PRODUCTOS CUANDO SE USA ELECTRICOS, LAS PRECAUCIONES BÁSICAS
SIEMPRE SE DEBEN SEGUIR, INCLUSIVE LO SIGUIENTE:
PELIGRO — EL RIESGO DE CALAMBRE. CONECTA SÓLO A UN CIRCUITO PROTEGIDO POR UN
INTERRUPTOR (GFCI) DE CIRCUITO DE DEFECTO DE SUELO.
PRECAUCIÓN — PRUEBA EL INTERRUPTOR DE CIRCUITO DE DEFECTO DE SUELO QUE PROTEGE
ESTE APARATO PERIODICAMENTE DE ACUERDO CON LAS INSTRUCCIONES DEL FABRICANTE.
ADVERTENCIA—UTILIZAESTAUNIDADSOLOPARASUUSODESTINADODESCRIBIOCOMOENESTE
MANUAL. NO UTILICE LAS FIJACIONES NO RECOMENDADO POR LOS FABRICANTES.
ADVERTENCIA — PARA EVITAR LESIONES, TENGA CUIDADO AL ENTRAR Y SALIR DE LA TINA DE
HIDROMASAJE.
ADVERTENCIA — MANTENGA EL CUERPO Y EL CABELLO A UNA DISTANCIA MÍNIMA DE 6 PULG. (15
CM) DEL ACCESORIO DE SUCCIÓN MIENTRAS EL SISTEMA DE HIDROMASAJE ESTÉ EN FUNCIONA-
MIENTO. SI EL LARGO DEL CABELLO EXCEDE LOS HOMBROS, SE LO DEBE SUJETAR CERCA DE LA
CABEZA.
ADVERTENCIA — RIESGO DE DESCARGA ELÉCTRICA. NO UTILICE ELECTRODOMÉSTICOS, COMO
SECADORES DE CABELLO, LÁMPARAS, TELÉFONOS, RADIOS O TELEVISORES, EN UN RADIO DE 60
PULG. (1,5 M) DE LA TINA DE HIDROMASAJE.
ADVERTENCIA —ELRIESGODELAHERIDAACCIDENTALOAHOGANDOSE;NOUTILICELASDROGAS
O EL ALCOHOL ANTES O DURANTE EL USO DE BAÑERA DE HYDROMASSAGE EQUIPADA CON UNA
CALENTADORA PARA EVITAR LA INCONSCIENCIA Y AHOGAR POSIBLE.
ADVERTENCIA — RIESGO DE LESIÓN FETAL. LAS MUJERES EMBARAZADAS O QUE PUEDAN ESTARLO
DEBEN CONSULTARAUN MÉDICOANTES DE UTILIZAR UNATINADE HIDROMASAJE CON CALENTADOR.
ADVERTENCIA — RIESGO DE HIPERTERMIA Y POSIBILIDAD DE AHOGARSE. NO UTILICE UNA TINA DE
HIDROMASAJE CON CALENTADOR INMEDIATAMENTE DESPUÉS DE HACER EJERCICIOS INTENSOS.
ADVERTENCIA — RIESGO DE HIPERTERMIA Y POSIBILIDAD DE AHOGARSE. LATEMPERATURA DEL
AGUAQUE SUPERE LOS 104°F (40°C) PUEDE SER PERJUDICIALPARALASALUD. CONTROLE Y REGU-
LE LATEMPERATURA DELAGUAANTES DE UTILIZAR LATINA.
ADVERTENCIA — RIESGO DE HIPERTERMIA. LAS PERSONAS QUE TOMEN MEDICAMENTOS O QUE
TENGAN UNA HISTORIACLÍNICA PROBLEMÁTICADEBEN CONSULTAR AUN MÉDICO ANTES DE UTILI-
ZAR UNA TINA DE HIDROMASAJE CON CALENTADOR.
PARA INCORPORADO Y LAS UNIDADES DE GOTA-EN, INSTALAN PARA PERMITIR ELACCESO PARA
ATENDER A.
ESTA UNIDAD SE DEBE MOLER ELÉCTRICAMENTEY DEBE SER INSTALADA POR UN CONTRATISTA
LICENCIADO, POR EL ELECTRICISTA, Y POR EL PLOMERO.
LAS MATERIAS DEL EDIFICIO Y ELALAMBRADO SE DEBEN DIRIGIR LEJOS DE LAMOTRIZ/BOMBAO
FUELLE U OTRO CALOR QUE PRODUCE LOS COMPONENTES DE ESTA UNIDAD.
EL MOTOR Y EL CALENTADOR TIENEN EN SU PARTE EXTERIOR UN CONECTOR DE CABLE A PRE-
SIÓN PARA PERMITIR LA CONEXIÓN DE UN CONDUCTOR DE UNIÓN SÓLIDO DE COBRE #8 AWG (8,4
MM) ENTRE ESTAUNIDAD Y EL RESTO DE LOS EQUIPOS ELÉCTRICOS Y METALES EXPUESTOS CER-
CANOS, A FIN DE CUMPLIR CON LAS NORMAS LOCALES.
PRECAUCIONES
• Ponga en funcionamiento el sistema de hidromasaje sólo cuando la tina tenga un nivel de agua que supere en 1 a 2
pulgas (2,5 - 5,08 cm) como mínimo a la boquilla de aire más alta.
• No llene en exceso la tina para evitar que el panel de control quede sumergido.
• No utilice aditivos para baño a base de aceites en la tina de hidromasaje.
• No utilice sustancias abrasivas para limpiar la tina, ya que pueden arruinar la superficie.
• Para evitar la decoloración del acabado acrílico, no llene la tina con agua a más de 140°F (60°C).
NOTA: Este producto debe ser instalado por profesionales. Es necesario contar con conocimientos de téc-
nicas de construcción, instalaciones eléctricas y plomería de acuerdo con las normas para lograr una insta-
lación adecuada y la satisfacción del usuario. Recomendamos que la instalación de todos los productos
Jacuzzi Whirlpool Bath esté a cargo de un contratista matriculado. Nuestra garantía no cubre problemas
relacionados con instalaciones defectuosas.
LAS ESPECIFICACIONES DE LOS PRODUCTOS ESTÁN SUJETAS A CAMBIOS SIN AVISO.
UTILICE LAS INSTRUCCIONES DE INSTALACIÓN ENTREGADAS CON EL PRODUCTO.
La empresa ha obtenido los listados de los códigos aplicables (normas) que suelen estar disponibles a nivel nacional para
productos de este tipo. Es responsabilidad del instalador o propietario determinar el cumplimiento de las normas locales
específicas antes de instalar el producto. La empresa no realiza manifestaciones ni ofrece garantías con respecto al cumpli-
miento de ninguna norma, ni será responsable de dicho cumplimiento.
3
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLA DE CONTENIDO
Instrucciones de seguridad ______________________________________________________________ 2-3
Tabla de contenido _____________________________________________________________________ 4
Especificaciones ______________________________________________________________________ 5-9
Diagramas de instalaciones ______________________________________________________________ 10-17
Recorte ______________________________________________________________________________ 17
Instrucciones de instalación ______________________________________________________________ 18-24
Estructura y soporte __________________________________________________________________ 18
Faldón _____________________________________________________________________________ 19
Registros __________________________________________________________________________ 20
Conexiones eléctricas_________________________________________________________________ 21
Plomería y suministro de agua __________________________________________________________ 22
Instrucciones de instalación de undermount _______________________________________________ 23-24
Funcionamiento _______________________________________________________________________ 25-26
Mantenimiento_________________________________________________________________________ 27
Guía general de reoaro de fallas___________________________________________________________ 28
Servicios autorizados ___________________________________________________________________ 30
La garantía ___________________________________________________________________________ 31-32
NOTA: Obtener una referencia para un agente del servicio en su 1-(800)-288-4002 de la llamada de área. Usted
Para encontrar las listas de agente de servicio para:
Las Reparaciones eléctricas o Mecánicas visitan http://jacuzzi.com/pdf/ASA.PDF
El fin, la Superficie, o las Reparaciones de Esqueleto-Relacionó visitan http://jacuzzi.com/pdf/AFC.PDF
La reparación Despide o los Accesorios visitan http://jacuzzi.com/pdf/MPD.PDF
4
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPECIFICACIONES
Importante: Lea las instrucciones antes de iniciar la instalación.
Las tinas de hidromasaje se entregan listas para instalarse y completamente equipadas con motor, bomba, accesorios de
plomería y mecanismos necesarios para el hidromasaje. La instalación del equipo de desagüe y rebosadero es opcionál.
Saque la tina de su caja; consérvela hasta haber revisado completamente el producto. No levante la tina sujetándola por
los accesorios de plomería, sino por el casco.
Inspeccione el casco de la tina en cuanto la reciba. En caso de que detecte algún daño o desperfecto en el terminado, no la
instale. La garantía no cubre daños o desperfectos reclamados después de la instalación. La responsabilidad de Jacuzzi
Whirlpool Bath por daños de embarque termina al entregar los productos en buen estado al distribuidor. Presente sus reclama-
ciones por daños al distribuidor. Para mayor información sobre la cobertura de la garantía, consulte la garantía publicada en el
empaque del producto.
El funcionamiento de las tinas y el buen estado de las conexiones han sido probados en fábrica antes del embarque. Nota:
Antes de la instalación, llene la tina con agua y enciéndala para verificar que no presente fugas provocadas durante el
embarque o por mal manejo. Jacuzzi Whirlpool Bath no se hace responsable por desperfectos que pudieran haberse descu-
bierto, reparado o evitado de haberse seguido este procedimiento de inspección y verificación.
No todas tinas mostradas pueden estar disponibles como unidades de exportación. Las tinas de la exportación vienen con
controles MANUALES y pueden venir:
• con el Bomba/Motor embaló separadamente,
• con el Bomba/Motor instaló,
• con ningún recorte de capacidad excesiva.
A causa de la variedad de tina de exportación escribe a máquina algunas instrucciones no pueden aplicar a su unidad.
Desatienda las instrucciones que no aplican a su tina específica.
TINAS RECTANGULAR
L
W
(51 mm)
2"
(25 mm)
1"
L
W
H
H
VISTA LATERAL
VISTA DE FRENTE
VISTA DE FRENTE
VISTA LATERAL
TINAS SIN FALDÓN INTEGRADO
TINAS CON FALDÓN INTEGRADO
(25 mm)
1"
L
W
H
A
VISTA DE FRENTE
VISTA LATERAL
B
TINAS CON PESTAÑA DE 3 LADOS
DESAGÜE/REBOSADERO
ESPECIFICACIONES (Rectangular) LH = Mano Izquierda, RH = Mano Derecha
CALENTADOR LISTO
PARA LA INSTALACIÓN
DEL CAMPO
MEDIDAS DEL
DESAGÜE/
REBOSADERO
FALDÓN Y
MONTAJE
CARGA TOTAL
SOBRE EL PISO
MODELO
AMIGA™
MEDIDAS
PESO
CORTE
CAPACIDAD
70" x 34"
(1778 mm x
864 mm)
16-7/8" (429 mm) A
50 U.S. gal
(186 litros)
Opcional,
marco en “U”
772 lb
105 lb
(48 kg)
Si
72"
36"
(1829 mm) L*
( 914 mm) W
20-3/4" ( 533 mm) H
14"
(356 mm) B
(351 kg)/
(S750000 HEATER JUEGO)
43 lb/pies2
(210 kg/m2)
LH & RH
NA
AMIGA™
CON FALDÓN
INTEGRADO
16-7/8" (429 mm) A
50 U.S. gal
(186 litros)
Integrado
796 lb
129 lb
(59 kg)
72"
36"
(1829 mm) L*
( 914 mm) W
Si
14"
(356 mm) B
(362 kg)/
(S750000 HEATER JUEGO)
44 lb/pies2
(214 kg/m2)
20-3/4" ( 533 mm) H
LH & RH
BIANCA©
16"
(406 mm) A
70" x 46"
993 lb
73 U.S. gal
(276 litros)
Opcional,
marco en “U”
135 lb
(61 kg)
72"
48"
(1829 mm) L*
(1219 mm) W
Si
8-1/2" (216 mm) B (1778 mm x
1168 mm)
(451 kg)/
41 lb/pies2
(200 kg/m2)
(S750000 HEATER JUEGO)
LH
20-1/2" ( 521 mm) H
NA
CETRA©
17-7/8" (454 mm) A
9-3/8" (238 mm) B
94 lb
(43 kg)
Integrado
727 lb
46 U.S. gal
(174 litros)
60"
32"
(1524 mm) L*
( 813 mm) W
Si
(330 kg)/
CON FALDÓN
INTEGRADO
LH & RH
(S750000 HEATER JUEGO)
55 lb/pies2
(268 kg/m2)
20-1/2" ( 521 mm) H
CETRA© 532
58" x 30-1/4"
(1473 mm x
768 mm)
43 U.S. gal
(163 litros)
Opcional,
marco en “U”
18-1/2" ( 470 mm) A
697 lb
89 lb
(41 kg)
60"
(1524 mm) L*
Si
9"
( 229 mm) B
(317 kg)/
31-7/8" ( 791 mm) W
21-1/4" ( 553 mm) H
53 lb/pies2
(259 kg/m2)
(S750000 HEATER JUEGO)
LH & RH
CETRA© 536
LH & RH
48 U.S. gal
(181 litros)
Opcional,
marco en “U”
58" x 34-1/4"
(1473 mm x
870 mm)
18-1/2" ( 470 mm) A
742 lb
92 lb
(42 kg)
60"
36"
(1524 mm) L*
( 914 mm) W
Si
9"
( 229 mm) B
(337 kg)/
50 lb/pies2
(244 kg/m2)
(S750000 HEATER JUEGO)
21-1/4" ( 553 mm) H
*Añada 1/4" (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: Las dimensiones en general son nominales con una tolerancia de +0 y -1/4" (6,4 mm).
PARA TODAS LAS UNIDADES: Requisitos eléctricos del servicio: Todas requieren un circuito dedicado independiente y protegido con un GFCI.
(Opcional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicó GFCI protegió circuito separado.
Motor/Bomba: 115 VAC., 15 AMP, 60 Hz. dedicó GFCI protegió circuito separado.
5
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPECIFICACIONES
ESPECIFICACIONES (Rectangular) LH = Mano Izquierda, RH = Mano Derecha
MEDIDAS DEL
DESAGÜE/
REBOSADERO
CALENTADOR LISTO
PARA LA INSTALACIÓN
DEL CAMPO
FALDÓN Y
MONTAJE
CARGA TOTAL
SOBRE EL PISO
MODELO
MEDIDAS
PESO
CORTE
CAPACIDAD
CETRA© 536
CON FALDÓN
INTEGRADO
LH & RH
18-1/2" ( 470 mm) A
NA
48 U.S. gal
(181 litros)
Integrado
742 lb
92 lb
(42 kg)
Si
60"
36"
(1524 mm) L*
9"
( 229 mm) B
(337 kg)/
(S750000 HEATER JUEGO)
( 914 mm) W
50 lb/pies2
(244 kg/m2)
21-1/4" ( 553 mm) H
LUXURA™ 5
CON PESTAÑA
DE 3 LADOS
INTEGRADA
LH & RH
60"
32"
(1524 mm) L
( 813 mm) W
NA
697 lb
80 lb
(36 kg)
Opcional,
marco en “U”
44 U.S. gal
(167 litros)
15-1/4" (387 mm) A
8-1/4" (210 mm) B
Si
Pestaña
Moldeada
de Azulejo
(264 kg)/
52 lb/pies2
(254 kg/m2)
(S750000 HEATER JUEGO)
20-1/4" ( 514 mm) H
LUXURA™ 5
CON FALDÓN
INTEGRADO
LH & RH
NA
60"
32"
(1524 mm) L
( 813 mm) W
700 lb
100 lb
(45 kg)
Integrado
42 U.S. gal
(159 litros)
15-1/4" (387 mm) A
8-1/4" (210 mm) B
Si
(318 kg)/
53 lb/pies2
(259 kg/m2)
(S750000 HEATER JUEGO)
20-1/4" ( 514 mm) H
Si
LUXURA™ 5.5
LH & RH
15-1/4" (387 mm) A
8-3/8" (213 mm) B
823 lb
90 lb
(41 kg)
Opcional,
marco en “U”
64" x 32"
(1626 mm x
813 mm)
58 U.S. gal
(220 litros)
66"
(1676 mm) L*
( 864 mm) W
( 508 mm) H
(S750000 HEATER JUEGO)
(374 kg)/
53 lb/pies2
(259 kg/m2)
34"
20"
16-3/4" (425 mm) A
9-1/4" (235 mm) B
Si
662 lb
LUXURA™ 530
CON FALDÓN
INTEGRADO
LH & RH
NA
38 U.S. gal
(144 litros)
95 lb
(43 kg)
Integrado
60"
30"
(1524 mm) L*
(U395000 HEATER JUEGO)
(301 kg)/
53 lb/pies2
(259 kg/m2)
( 762 mm) W
20-1/4" ( 483 mm) H
46 U.S. gal
(172 litros)
15"
(381 mm) A
MAJORA© 5
LH & RH
60"
42"
(1524 mm) L*
58" x 40"
(1473 mm x
1013 mm)
728 lb
95 lb
(43 kg)
No Disponible
Si
8-3/4" (222 mm) B
(331 kg)/
(S750000 HEATER JUEGO)
(1067 mm) W
42 lb/pies2
(205 kg/m2)
19-1/2" ( 495 mm) H
MAJORA©
LH & RH
6
15-5/8" (397 mm) A
10-1/2" (267 mm) B
70" x 40"
(1778 mm x
1016 mm)
937 lb
104 lb
(47 kg)
No Disponible
Integrado
70 U.S. gal
(265 litros)
Si
72"
42"
(1829 mm) L*
(423 kg)/
44 lb/pies2
(215 kg/m2)
(S750000 HEATER JUEGO)
(1067 mm) W
19-3/4" ( 502 mm) H
MAJORA©
6
15-5/8" (397 mm) A
10-1/2" (267 mm) B
NA
947 lb
114 lb
(52 kg)
70 U.S. gal
(265 litros)
Si
72"
42"
(1829 mm) L*
(1067 mm) W
CON FALDÓN
INTEGRADO
LH & RH
(430 kg)/
(S750000 HEATER JUEGO)
45 lb/pies2
(220 kg/m2)
19-3/4" ( 502 mm) H
MITO©
5
58" x 40"
(1473 mm x
1016 mm)
866 lb
62 U.S. gal
(235 litros)
100 lb
(45 kg)
Opcional,
marco en “U”
17-1/2" (445 mm) A
11-7/8" (302 mm) B
Si
60"
(1524 mm) L*
(1067 mm) W
( 533 mm) H
(394 kg)/
50 lb/pies2
(244 kg/m2)
(S750000 HEATER JUEGO)
42"
21"
LH & RH
MITO©
6
(1829 mm) L* 17-1/2" (445 mm) A
76 U.S. gal
(288 litros)
110 lb
(50 kg)
No Disponible
Si
993 lb
70" x 40"
(1778 mm x
1016 mm)
72"
42"
11-7/8" (302 mm) B
(1067 mm) W
(S750000 HEATER JUEGO)
(451 kg)/
47 lb/pies2
(229 kg/m2)
LH & RH
21-1/2" ( 546 mm) H
NOVA©
5
Si
60"
42"
(1524 mm) L*
58" x 40"
(1473 mm x
1016 mm)
45 U.S. gal
(170 litros)
Opcional,
marco en “U”
14-3/4" (375 mm) A
8-1/2" (216 mm) B
722 lb
97 lb
(44 kg)
(S750000 HEATER JUEGO)
(328 kg)/
41 lb/pies2
(200 kg/m2)
(1067 mm) W
LH & RH
18-1/2" ( 470 mm) H
*Añada 1/4" (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: Las dimensiones en general son nominales con una tolerancia de +0 y -1/4" (6,4 mm).
PARA TODAS LAS UNIDADES: Requisitos eléctricos del servicio: Todas requieren un circuito dedicado independiente y protegido con un GFCI.
(Opcional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicó GFCI protegió circuito separado.
Motor/Bomba: 115 VAC., 15 Amp, 60 Hz. dedicó GFCI protegió circuito separado.
6
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPECIFICACIONES
ESPECIFICACIONES (Rectangular) LH = Mano Izquierda, RH = Mano Derecha
MEDIDAS DEL
DESAGÜE/
REBOSADERO
CALENTADOR LISTO
PARA LA INSTALACIÓN
DEL CAMPO
FALDÓN Y
MONTAJE
CARGA TOTAL
SOBRE EL PISO
MODELO
MEDIDAS
PESO
CORTE
CAPACIDAD
NOVA©
5
NA
722 lb
45 U.S. gal
(170 litros)
97 lb
(44 kg)
No Disponible
14-3/4" (375 mm) A
8-1/2" (216 mm) B
Si
60"
42"
(1524 mm) L*
CON PESTAÑA
DE 3 LADOS
INTEGRADA
LH & RH
Pestaña
Moldeada
de Azulejo
(328 kg)/
41 lb/pies2
(200 kg/m2)
(S750000 HEATER JUEGO)
(1067 mm) W
18-1/2" ( 470 mm) H
NOVA©
5
112 lb
(51 kg)
737 lb
45 U.S. gal
(170 litros)
Integrado
No
NA
60"
42"
(1524 mm) L* 15-7/8" (403 mm) A
CON FALDÓN
INTEGRADO
LH & RH
(335 kg)/
9-1/4" (235 mm) B
(1067 mm) W
42 lb/pies2
(205 kg/m2)
18-1/2" ( 470 mm) H
NOVA©
6
14-3/4" (375 mm) A
8-1/2" (216 mm) B
Si
70" x 40"
(1778 mm x
1016 mm)
876 lb
62 U.S. gal
(235 litros)
110 lb
(50 kg)
Opcional,
marco en “U”
72"
42"
(1829 mm) L*
(S750000 HEATER JUEGO)
(398 kg)/
42 lb/pies2
(205 kg/m2)
(1067 mm) W
LH & RH
20-1/2" ( 521 mm) H
NOVA© 536
LH & RH
15-1/8" (384 mm) A
42 U.S. gal
(159 litros)
83 lb
(38 kg)
58" x 34"
(1473 mm x
863 mm)
No Disponible
683 lb
Si
60"
36"
(1524 mm) L*
( 914 mm) W
9"
(229 mm) B
(310 kg)/
46 lb/pies2
(224 kg/m2)
(S750000 HEATER JUEGO)
19-1/4" ( 489 mm) H
NOVA© 536
CON FALDÓN
INTEGRADO
LH & RH
14-5/8" (372 mm) A
42 U.S. gal
(159 litros)
Si
NA
NA
698 lb
98 lb
(45 kg)
Integrado
Integrado
60"
36"
(1524 mm) L*
(S750000 HEATER JUEGO)
(317 kg)/
9"
(229 mm) B
( 914 mm) W
47 lb/pies2
(229 kg/m2)
19-1/4" ( 489 mm) H
NOVA© 636
CON FALDÓN
INTEGRADO
LH & RH
14-5/8" (372 mm) A
9-3/8" (238 mm) B
56 U.S. gal
(223 litros)
824 lb
108 lb
(49 kg)
Si
72"
(1829 mm) L*
( 914 mm) W
( 483 mm) H
(375 kg)/
(S750000 HEATER JUEGO)
36"
19"
47 lb/pies2
(229 kg/m2)
SIGNA©
5
108 lb
(49 kg)
Si
60"
(1524 mm) L*
(1067 mm) W
( 559 mm) H
708 lb
42 U.S. gal
(159 litros)
17-1/2" (445 mm) A
12-1/2" (318 mm) B (1473 mm x
1016 mm)
58" x 40"
Opcional,
marco en “U”
(S750000 HEATER JUEGO)
(321 kg)/
42"
22"
40 lb/pies2
(195 kg/m2)
LH & RH
SIGNA©
5
Si
42 U.S. gal
(159 litros)
723 lb
126 lb
(56 kg)
60"
(1524 mm) L*
(1067 mm) W
( 559 mm) H
17-7/8" (451 mm) A
12-3/4" (330 mm) B
NA
Integrado
CON FALDÓN
INTEGRADO
MOTRIZ/BOMBA
CORRECTA
ANTERIOR
LH & RH
(U395000 HEATER JUEGO)
(329 kg)/
41 lb/pies2
(200 kg/m2)
42"
22"
SIGNA©
5
Si
NA
708 lb
108 lb
(49 kg)
17-1/2" (445 mm) A
12-1/2" (318 mm) B
42 U.S. gal
(159 litros)
Opcional,
marco en “U”
60"
(1524 mm) L*
(S750000 HEATER JUEGO)
CON PESTAÑA
DE 3 LADOS
INTEGRADA RH
(321 kg)/
40 lb/pies2
(195 kg/m2)
42" (1067 mm) W
22"
( 559 mm) H
SIGNA©
6
118 lb
(54 kg)
Si
55 U.S. gal
(208 litros)
826 lb
70" x 40"
(1778 mm x
1016 mm)
No Disponible
16-7/8" (429 mm) A
72"
(1829 mm) L*
(1067 mm) W
( 559 mm) H
(S750000 HEATER JUEGO)
(375 kg)/
39 lb/pies2
(190 kg/m2)
14"
(356 mm) B
42"
22"
LH & RH
*Añada 1/4" (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: Las dimensiones en general son nominales con una tolerancia de +0 y -1/4" (6,4 mm).
PARA TODAS LAS UNIDADES: Requisitos eléctricos del servicio: Todas requieren un circuito dedicado independiente y protegido con un GFCI.
(Opcional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicó GFCI protegió circuito separado.
Motor/Bomba: 115 VAC., 15 Amp, 60 Hz. dedicó GFCI protegió circuito separado.
7
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPECIFICACIONES
TINAS OVALADAS SIN BORDES
W
L
L
W
2'' (51 mm)
7-1/2"
(191 mm)
H
3-1/2"
(89 mm)
8"
H
2"
(51 mm)
(203 mm)
VISTA DE FRENTE
VISTA LATERAL
VISTA DE FRENTE
W
VISTA LATERAL
FRESCO
MILANO
L
L
W
2"
(51 mm)
H
2''
(51 mm)
H
VISTA LATERAL
VISTA DE FRENTE
VISTA DE FRENTE
VISTA LATERAL
LUNA
RIVA 5 & RIVA 6
GALLERY 5 & GALLERY 6
A
B
DESAGÜE/REBOSADERO
ESPECIFICACIONES (Ovaladas) LH = Mano Izquierda, RH = Mano Derecha
MEDIDAS DEL
DESAGÜE/
REBOSADERO
CALENTADOR LISTO
PARA LA INSTALACIÓN
DEL CAMPO
FALDÓN Y
MONTAJE
CARGA TOTAL
SOBRE EL PISO
MODELO
FRESCO©
LH & RH
MEDIDAS
CORTE
CAPACIDAD
PESO
Si
20-1/8" (511 mm) A
11-3/4" (299 mm) B
Plantilla
Poveida
P/N
921 lb
63 U.S. gal
(239 litros)
146 lb
(66 kg)
No
Disponible
71-1/2" (1816 mm) L
(1067 mm) W
27-1/4" ( 692 mm) H*
(S750000 HEATER JUEGO)
(419 kg)/
44 lb/pies2
(220 kg/m2)
42"
P188000
GALLERY™ 5
OVALADAS
14-3/4" (375 mm) A
9-1/2" (241 mm) B
Plantilla
Poveida
P/N
Si
746 lb
48 U.S. gal
(182 litros)
96 lb
(44 kg)
No
Disponible
62"
43"
19"
(1575 mm) L
(1092 mm) W
( 483 mm) H
(S750000 HEATER JUEGO)
(339 kg)/
40 lb/pies2
(195 kg/m2)
LH & RH
P186000
GALLERY™ 6
OVALADAS
871 lb
16"
(406 mm) A
105 lb
(48 kg)
62 U.S. gal
(235 litros)
No
Disponible
Plantilla
Poveida
P/N
Si
72"
42"
(1829 mm) L
(1067 mm) W
(395 kg)/
42 lb/pies2
(205 kg/m2)
11-1/2" (292 mm) B
(S750000 HEATER JUEGO)
20-1/2" ( 521 mm) H
LH & RH
P186000
GALLERY™ 6
OVALADAS
UNDERMOUNT
871 lb
16"
(406 mm) A
105 lb
(48 kg)
62 U.S. gal
(235 litros)
No
Disponible
Plantilla
Poveida
P/N
72"
42"
(1829 mm) L
(1067 mm) W
Si
(395 kg)/
42 lb/pies2
(205 kg/m2)
11-1/2" (292 mm) B
(S750000 HEATER JUEGO)
20-1/2" ( 521 mm) H
X302000
LH & RH
LUNA™
Si
1221 lb
(555 kg)/
58 lb/pies2
(283 kg/m2)
96 U.S. gal
(364 litros)
121 lb
(55 kg)
72"
42"
23"
(1829 mm) L
(1067 mm) W
( 584 mm) H
19-1/8" (486 mm) A
Plantilla
Poveida
P/N
No
Disponible
(S750000 HEATER JUEGO)
11"
(279 mm) B
RH
P819000
MILANO™
LH & RH
72"
40"
(1816 mm) L
(1016 mm) W 11"
18-1/2" (470 mm) A
Plantilla
Poveida
P/N
893 lb
60 U.S. gal
(227 litros)
143 lb
(65 kg)
No
Disponible
Si
(279 mm) B
(406 kg)/
(S750000 HEATER JUEGO)
20-3/4" ( 527 mm) H
45 lb/pies2
(220 kg/m2)
P188000
Si
OPALIA™
LH & RH
18-3/4" (476 mm) A
Plantilla
Poveida
P/N
145 lb
(66 kg)
70 U.S. gal
(265 litros)
72"
44"
(1829 mm) L
(1118 mm) W
978 lb
No
Disponible
(S750000 HEATER JUEGO)
12"
(305 mm) B
(445 kg)
45 lb/pies2
(220 kg/m2)
22-1/4" ( 565 mm) H
P186000
RIVA©
RH
5
14-3/4" (375 mm) A
9-1/2" (241 mm) B
Plantilla
Poveida
P/N
No
Disponible
Si
746 lb
48 U.S. gal
(182 litros)
96 lb
(44 kg)
62"
43"
19"
(1575 mm) L
(1092 mm) W
( 483 mm) H
(S750000 HEATER JUEGO)
(339 kg)/
40 lb/pies2
(195 kg/m2)
P186000
RIVA©
6
871 lb
No
Disponible
16"
(406 mm) A
72"
42"
(1829 mm) L
(1067 mm) W
105 lb
(48 kg)
62 U.S. gal
(235 litros)
Plantilla
Poveida
P/N
Si
(396 kg)/
42 lb/pies2
(205 kg/m2)
11-1/2" (292 mm) B
(S750000 HEATER JUEGO)
LH & RH
20-1/2" ( 521 mm) H
P186000
* Para el Fresco™ modela H551, H549, y H550 que esta altura es 23-3/4 pulg.
NOTA: Las dimensiones en general son nominales con una tolerancia de +0 y -1/4" (6,4 mm).
PARA TODAS LAS UNIDADES: Requisitos eléctricos del servicio: Todas requieren un circuito dedicado independiente y protegido con un GFCI.
(Opcional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicó GFCI protegió circuito separado.
Motor/Bomba: 115 VAC., 15 Amp, 60 Hz. dedicó GFCI protegió circuito separado.
8
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPECIFICACIONES
TINAS DE ESQUINA
A
2"
H
(51 mm)
B
DESAGÜE/REBOSADERO
VISTA DE FRENTE
VISTA LATERAL
TINAS DE ESQUINA
1"
H
(25 mm)
VISTALATERAL
VISTADE FRENTE
CAPELLA 55, CAPELLA 60, & TARA CON FALDÓN INTEGRADO
1"
H
(25 mm)
VISTA LATERAL
VISTA DE FRENTE
CAPELLA SPACESAVER CON FALDÓN INTEGRADO
ESPECIFICACIONES (De Esquina) LH = Mano Izquierda, RH = Mano Derecha
MEDIDAS DEL
DESAGÜE/
REBOSADERO
CALENTADOR LISTO
PARA LA INSTALACIÓN
DEL CAMPO
FALDÓN Y
MONTAJE
CARGA TOTAL
SOBRE EL PISO
MODELO
MEDIDAS
CORTE
CAPACIDAD
PESO
CAPELLA© 55
Si
55"
55"
(1397 mm) L
(1397 mm) L
51 U.S. gal
(193 litros)
17-1/2" (445 mm) A
9-5/8" (245 mm) B
Opcional
Vea
Pagina 17
791 lb
116 lb
(53 kg)
(S750000 HEATER JUEGO)
(360 kg)/
38 lb/pies2
(185 kg/m2)
RH
20-1/4" ( 514 mm) H
CAPELLA© 55
CON FALDÓN
INTEGRADO
55"
55"
(1397 mm) L
(1397 mm) L
18"
(457 mm) A
NA
NA
54 U.S. gal
(204 litros)
833 lb
125 lb
(57 kg)
Integrado
No
12-1/8" (308 mm) B
(379 kg)/
40 lb/pies2
(195 kg/m2)
20-1/2" ( 521 mm) H
RH
CAPELLA©
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
60 U.S. gal
(227 litros)
880 lb
130 lb
(59 kg)
Integrado
No
No
SPACESAVER
CON FALDÓN
INTEGRADO RH
12-3/8" (308 mm) B
(400 kg)/
35 lb/pies2
(171 kg/m2)
20-1/2" ( 521 mm) H
CAPELLA© 60
MOTOR/BOMBA
DELANTERO
IZQUIERDO
LH
18"
(457 mm) A
Vea
Pagina 17
60 U.S. gal
(227 litros)
870 lb
120 lb
(54 kg)
No
Disponible
60"
60"
(1524 mm) L
(1524 mm) L
12-1/8" (308 mm) B
(395 kg)/
35 lb/pies2
(171 kg/m2)
20-1/2" ( 521 mm) H
CAPELLA© 60
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
Vea
Pagina 17
60 U.S. gal
(227 litros)
870 lb
120 lb
(54 kg)
No
Disponible
No
No
12-1/8" (308 mm) B
(395 kg)/
35 lb/pies2
(171 kg/m2)
LH & RH
20-1/2" ( 521 mm) H
CAPELLA© 60
CON FALDÓN
INTEGRADO
RH
60"
60"
(1524 mm) L
(1524 mm) L
18"
(457 mm) A
NA
60 U.S. gal
(227 litros)
880 lb
130 lb
(59 kg)
Integrado
12-1/8" (308 mm) B
(400 kg)/
35 lb/pies2
(171 kg/m2)
20-1/2" ( 521 mm) H
Si
GALLERY™
ESQUINA
74 U.S. gal
(280 litros)
Vea
Pagina 17
60"
60"
(1524 mm) L
(1524 mm) L
984 lb
118 lb
(54 kg)
18-1/8" (451 mm) A
No
Disponible
(S750000 HEATER JUEGO)
(447 kg)/
39 lb/pies2
(244 kg/m2)
12"
16"
(305 mm) B
(406 mm) A
22-1/2" ( 572 mm) H
LH & RH
Si
TARA™
LH & RH
60"
60"
(1524 mm) L
(1524 mm) L
74 U.S. gal
(280 litros)
984 lb
118 lb
(54 kg)
Opcional
Integrado
Vea
Pagina 17
(S750000 HEATER JUEGO)
12-3/8" (314 mm) B
(447 k/g)/
39 lb/pies2
(190 kg/m2)
20-3/4" ( 527 mm) H
TARA™
60"
60"
(1524 mm) L
(1524 mm) L
16"
(406 mm) A
74 U.S. gal
(280 litros)
No
999 lb
133 lb
(61 kg)
NA
CON FALDÓN
INTEGRADO
RH
12-3/8" (314 mm) B
(454 k/g)/
40 lb/pies2
(195 kg/m2)
20-3/4" ( 527 mm) H
NOTA: Las dimensiones en general son nominales con una tolerancia de +0 y -1/4" (6,4 mm).
PARA TODAS LAS UNIDADES: Requisitos eléctricos del servicio: Todas requieren un circuito dedicado independiente y protegido con un GFCI.
(Opcional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicó GFCI protegió circuito separado.
Motor/Bomba: 115 VAC., 15 Amp, 60 Hz. dedicó GFCI protegió circuito separado.
9
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (RECTANGULAR)
*72''
*72''
*72''
Motor
17-3/8"
18''
18''
Motor
Motor
16'' x 4''
16'' x 4''
16'' x 4''
36''
36''
11-1/8''
36''
2''
11-1/8''
11-1/8''
Acceso opcional de Servicio
Acceso opcional de
Servicio
2''
2''
14''
14''
14-1/2"
AMIGA™, Mano Derecha
AMIGA™, Mano Izquierda
AMIGA™ CON FALDÓN INTEGRADO,
Mano izquierda
*72"
*72''
Motor
*60"
24"
48"
13-1/2" x 4"
15-5/8"
17-3/8''
10" x 4"
16'' x 4''
32"
Motor
Motor
36''
5-11/16"
2"
9-3/8"
2''
14-1/2''
8-1/2"
11-1/8''
2"
13-3/4"
Acceso opcional de Servicio
CETRA™ CON FALDÓN INTEGRADO,
Mano Izquierda
(Mano izquierda (como mostrado) solamente)
AMIGA™ CON FALDÓN INTEGRADO,
BIANCA™
Mano derecha
*60"
*60"
*60"
12" x 4"
15-5/8"
12" x 4"
10" x 4"
32"
32"
32"
16"
Motor
Motor
Motor
16"
2"
9-3/8"
5-11/16"
2"
5-3/4"
5-3/4"
9"
2"
Acceso opcional de Servicio
Acceso opcional de Servicio
9"
CETRA™ CON FALDÓN INTEGRADO,
Mano Derecha
CETRA™ 532, Mano Derecha
CETRA™ 532, Mano Izquierda
*60"
*60"
*60"
17-3/8"
5-3/4"
12" x 4"
12" x 4"
12" x 4"
36"
Motor
36"
36"
Motor
Motor
18"
5-3/4"
18"
2"
9"
2"
2"
5-3/4"
Acceso opcional de Servicio
Acceso opcional de Servicio
9"
9"
CETRA™ 536, Mano Derecha
CETRA™ 536 CON FALDÓN INTEGRADO,
Mano Izquierda
CETRA™ 536, Mano Izquierda
*60"
*60"
*60"
8-1/4"
8-1/4"
17-3/8"
5-3/4"
12" x 4"
16"
32"
12" x 5"
16"
15" x 5"
36"
Motor
Motor
32"
Motor
2-1/2"
5-1/4"
2-1/2"
2-1/2"
Acceso opcional de Servicio
2-1/2"
5-1/4"
2"
Acceso opcional de Servicio
LUXURA™ 5, Mano Izquierda
9"
LUXURA™ 5, Mano Derecha
CETRA™ 536 CON FALDÓN INTEGRADO,
Mano Derecha
*Añada 1/4 pulgadas (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las unidades
que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
10
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (RECTANGULAR)
*60"
*60"
*66"
8-1/4"
8-1/4"
8-3/8"
15-3/8"
15-3/8"
12" x 5"
12" x 5"
17"
32"
32"
12" x 5"
Motor
Motor
34"
2-1/2"
5-1/4"
Motor
2-1/2"
5-1/4"
2-1/2"
5-3/8"
2-1/2"
2-1/2"
LUXURA™ 5 CON FALDÓN INTEGRADO
,
LUXURA™ 5 CON FALDÓN INTEGRADO
,
2-1/2"
Acceso opcional de Servicio
Mano Derecha
Mano Izquierda
LUXURA™ 5.5, Mano Izquierda
*66"
*60"
*60"
8-3/8"
9-1/4"
9-1/4"
14-3/8"
17"
14-3/8"
12" x 5"
12" x 5"
12" x 5"
30"
34"
30"
Motor
Motor
Motor
2-1/2"
5-7/8"
2-1/2"
5-3/8"
2-1/2"
5-7/8"
2-1/2"
2-1/2"
2-1/2"
Acceso opcional de Servicio
LUXURA™ 530 CON FALDÓN INTEGRADO
,
LUXURA™ 530 CON FALDÓN INTEGRADO
,
Mano Izquierda
LUXURA™ 5.5, Mano Derecha
Mano Derecha
*60"
*60"
2"
*72"
2"
8-3/4"
21"
8-3/4"
10-1/2"
2"
21"
42"
21"
42"
10" x 4"
12" x 4"
10" x 4"
42"
Motor
Motor
Motor
4-3/8"
Acceso opcional de Servicio
4-3/8"
Acceso opcional de Servicio
4-3/8"
Acceso opcional de Servicio
MAJORA™ 5, Mano Derecha
MAJORA™ 6, Mano Izquierda
MAJORA™ 5, Mano Izquierda
*72"
2"
*72"
2"
*72"
2"
8-1/2"
8-1/2"
10-1/2"
20-1/2"
20-1/2"
21"
42"
12" x 4"
12" x 4"
12" x 4"
42"
42"
Motor
Motor
Motor
4-3/8"
4-3/8"
4-3/8"
Acceso opcional de Servicio
MAJORA™ 6 CON FALDÓN INTEGRADO,
Mano Derecha
MAJORA™ 6 CON FALDÓN INTEGRADO,
MAJORA™ 6, Mano Derecha
Mano Izquierda
12" H x 18" L
Acceso para
Servicio
12" H x 18" L
Acceso para
Servicio
12" H x 18" L
Acceso para
Servicio
*60"
*72"
*60"
10" x 4"
10" x 4"
10" x 4"
42"
42"
42"
2"
Motor
Motor
2"
2"
Motor
11-7/8"
11-7/8"
11-7/8"
30"
5-3/8"
5-3/8"
30"
5-3/8"
36"
Acceso opcional
de Servicio
Acceso opcional
de Servicio
Acceso opcional
de Servicio
MITO™ 5, Mano Izquierda
MITO™ 5, Mano Derecha
MITO™ 6, Mano Izquierda
*Añada 1/4 pulgadas (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
11
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (RECTANGULAR)
12" H x 18" L
Acceso para
Servicio
12" H x 18" L
Acceso para
Servicio
12" H x 18" L
Acceso para
Servicio
*72"
*60"
*60"
10" x 4"
21"
21"
11" x 4"
11" x 4"
42"
42"
2"
Motor
42"
Motor
11-7/8"
Motor
Acceso opcional5-3/8"
5-3/8''
8-1/2''
36"
5-3/8''
8-1/2''
Acceso opcional de
Servicio
2''
Acceso opcional de
Servicio
de Servicio
2''
MITO™ 6, Mano Derecha
NOVA™ 5, Mano Derecha
NOVA™ 5, Mano Izquierda
12" H x 18" L
Acceso para Servicio
*60"
*60"
*60"
21"
11" x 4"
21"
21"
11" x 4"
42"
11" x 4"
42"
Motor
42"
Motor
Motor
5-1/4''
9-1/4"
5-1/4''
9-1/4"
2''
7''
Acceso opcional de
Servicio
2''
NOVA™ 5 CON FALDÓN INTEGRADO,
2''
8-1/2''
Mano Izquierda
NOVA™ 5 CON FALDÓN INTEGRADO,
Mano Derecha
NOVA™ 5 CON PESTAÑA DE 3 LADOS,
Mano Izquierda
12" H x 18" L
Acceso para Servicio
*60"
*60"
*60"
21"
18"
11" x 4"
18"
10" x 4"
42"
10" x 4"
36"
36"
Motor
Motor
Motor
7''
4-5/8"
4-5/8"
9"
Acceso opcional de
Acceso opcional de
Servicio
Acceso opcional de
Servicio
2"
2"
2''
8-1/2''
Servicio
9"
NOVA™ 536, Mano Izquierda
NOVA™ 536, Mano Derecha
NOVA™ 5 CON PESTAÑA DE 3 LADOS,
Mano Derecha
*72"
*60"
*60"
18"
21"
14" x 4"
10" x 4"
18"
36"
42"
10" x 4"
36"
Motor
Motor
Motor
6-7/8"
8-1/2"
4-5/8"
9"
Acceso opcional de
Servicio
2"
2"
4-5/8"
9"
2"
NOVA™ 6, Mano Izquierda
NOVA™ 536 CON FALDÓN INTEGRADO,
NOVA™ 536 CON FALDÓN INTEGRADO,
Mano Izquierda
Mano Derecha
*72"
*72"
9-3/8"
*72"
9-3/8"
17-7/8"
21"
17-7/8"
6-7/8"
10" x 4"
14" x 4"
10" x 4"
36"
42"
36"
Motor
Motor
Motor
2"
2"
6-7/8"
6-7/8"
8-1/2"
2"
Acceso opcional de
Servicio
NOVA™ 636 CON FALDÓN INTEGRADO,
Mano Izquierda
NOVA™ 636 CON FALDÓN INTEGRADO,
Mano Derecha
NOVA™ 6, Mano Derecha
*Añada 1/4 pulgadas (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
12
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (RECTANGULAR)
*60"
*60"
*60"
42"
42"
42"
12"
13" x 5"
13" x 5"
13" x 5"
Motor
Motor
Motor
12"
12"
Acceso
opcional
4-1/4"
Acceso
opcional
de Servicio
Acceso
4-1/4"
4-1/4"
5"
30"
opcional
5"
de Servicio
30"
5"
30"
de Servicio SIGNA™ 5, Mano Izquierda
SIGNA™ 5 CON PESTAÑA DE 3 LADOS,
Mano Izquierda
SIGNA™ 5, Mano Derecha
*60"
*60"
*72"
13" x 5"
42"
18-1/2" x 5"
16" x 5"
42"
42"
12"
Motor
Motor
Motor
12-3/4"
4-1/4"
Acceso
11-1/4"
12-1/2"
opcional
de Servicio
5"
30"
4-1/4"
30"
Acceso
5"
36"
6-3/4"
opcional
SIGNA™ 5 CON PESTAÑA DE 3 LADOS,
Mano Derecha
(Mano derecha (como mostrado) solamente)
de Servicio
SIGNA™ 6, Mano Izquierda
SIGNA™ 5 CON FALDÓN INTEGRADO
*72"
18-1/2" x 5"
42"
Motor
11-1/4"
12-1/2"
5"
Acceso
opcional
de Servicio
36"
SIGNA™ 6, Mano Derecha
*Añada 1/4 pulgadas (6,4 mm) a esta medida al instalar las unidades de 3 muros.
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
13
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (OVALADAS)
NOTA: Estas unidades se han proporcionado con plantillas de recorte incluidas en el envío el cartón.
Vea información de RECORTE para cada modelo en la página 8.
12" x 4"
12" x 4"
2"
42"
42"
Motor
2"
Motor
35-3/4"
35-3/4"
12" H x 18" L
12" H x 18" L
71-1/2"
71-1/2"
Acceso para Servicio
Acceso para Servicio
FRESCO™, Mano Derecha
FRESCO™, Mano Izquierda
62"
62"
21-1/2"
21-1/2"
12" x 4"
12" x 4"
43"
43"
Motor
Motor
5"
9-1/2"
5"
9-1/2"
12" H x 18" L
Acceso para Servicio
2"
12" H x 18" L
Acceso para Servicio
2"
GALLERY™ 5 OVALADAS, Mano Izquierda
GALLERY™ 5 OVALADAS, Mano Derecha
72"
72"
21"
21"
14" x 4"
14" x 4"
42"
42"
Motor
Motor
12" H x 18" L
Acceso para Servicio
2"
12" H x 18" L
Acceso para Servicio
2"
11-1/2"
11-1/2"
GALLERY™ 6, Mano Izquierda
GALLERY™ 6, Mano Derecha
2"
2"
12-1/2"
12-1/2"
14" x 4"
14" x 4"
42"
Motor
42"
Motor
21"
21"
72"
GALLERY™ 6 UNDERMOUNT, Mano Izquierda
72"
GALLERY™ 6 UNDERMOUNT, Mano Derecha
72"
71-1/2"
11"
71-1/2"
2"
11"
20"
2"
20"
40"
13" X 6"
3"
12" x 4"
12" x 4"
Motor
42"
Motor
Motor
40"
11"
5"
MILANO™, Mano Izquierda
5"
MILANO™, Mano Derecha
36"
(Mano derecha (como mostrado) solamente)
LUNA™
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
14
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (OVALADAS)
NOTA: Estas unidades se han proporcionado con plantillas de recorte incluidas en el envío el cartón.
Vea información de RECORTE para cada modelo en la página 8.
72"
72"
32"
12"
32"
13" X 4"
13" X 4"
44"
44"
3"
3"
12"
Motor
Motor
4-11/16"
36"
12" H x 18" L
Acceso para Servicio
4-11/16"
36"
12" H x 18" L
Acceso para Servicio
4"
4"
OPALIA™, Mano Derecha
OPALIA™, Mano Izquierda
62"
62"
21-1/2"
21-1/2"
12" x 4"
12" x 4"
43"
43"
Motor
Motor
5"
5"
12" H x 18" L
Acceso para Servicio
12" H x 18" L
Acceso para Servicio
9-1/2"
9-1/2"
2"
2"
(Mano izquierda (como mostrado) solamente)
(Mano izquierda (como mostrado) solamente)
RIVA™ 5
RIVA™ 5
72"
72"
21"
21"
14" x 4"
14" x 4"
42"
42"
Motor
Motor
6-7/8"
6-7/8"
2"
11-1/2"
2"
11-1/2"
RIVA™ 6, Mano Izquierda
12" H x 18" L
Acceso para Servicio
12" H x 18" L
Acceso para Servicio
RIVA™ 6, Mano Derecha
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
15
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
DIAGRAMAS EN PLANTA DE INSTALACIONES (ESQUINA)
55"
Acceso
opcional de
Servicio
32-1/4"
33-13/16"
Acceso
55"
60" opcional de
55"
60"
Servicio
55"
Motor
Motor
Acceso
12" x 4"
para
Motor
Acceso
para
16" X 4"
Servicio
14" X 4"
Servicio
27"
27"
26"
26"
29-3/8"
25-1/4"
36 1/2"
36 1/2"
32-1/2"
43-7/8"
25-1/4"
33-13/16"
6"
39 1/2"
9-7/8"
40-7/16"
49"
44 1/2"
41-9/16"
- 2" x 4" MURO
- CAJA DE CONEXCIONES
- CAJA DE CONEXCIONES
(Mano derecha (como mostrado) solamente)
(Mano derecha (como mostrado) solamente)
(Mano derecha (como mostrado) solamente)
CAPELLA™ 55
CAPELLA™ 55 CON FALDÓN INTEGRADO
CAPELLA™ SPACESAVER
Acceso
33-1/2"
opcional de
Servicio
33-1/2"
33-1/2"
60"
60"
Acceso
opcional de
Servicio
60"
60"
61-1/2"
Ref.
60"
60"
Motor
Motor
14" X 4"
Acceso para
Servicio
Acceso para
Servicio
14" X 4"
14" X 4"
27"
27"
34-15/16"
27"
27"
27"
6"
27"
43-1/8"
34-15/16"
6"
6"
34-15/16"
46-5/8"
46-5/8"
46-5/8"
43-1/8"
43-1/8"
CAPELLA 60 PARA IZQUIERDA DELANTERA
MOTOR/BOMBA,
CAPELLA™ 60, Mano Izquierda
CAPELLA™ 60, Mano Derecha
Mano Izquierda
Acceso
opcional de
Servicio
34"
Acceso
opcional de
Servicio
34"
33-1/2"
60"
60"
60"
60"
60"
60"
19" X 4"
19" X 4"
Motor
Acceso para
Servicio
Acceso para
Servicio
Motor
7-1/2"
Motor
7-1/2"
14" X 4"
24"
24"
27"
34-15/16"
24"
34"
24"
34"
27"
50-1/4"
50-1/4"
13"
6"
43-1/8"
46-5/8"
47-3/4"
47-3/4"
13"
GALLERY™ ESQUINA, Mano Izquierda
- CAJA DE CONEXCIONES
(Mano derecha (como mostrado) solamente)
CAPELLA™ 60 CON FALDÓN INTEGRADO
GALLERY™ ESQUINA, Mano Derecha
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
16
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAMAS DE INSTALACIONES
Acceso
opcional
de Servicio
Acceso
opcional
60"
60"
60"
60"
60"
de Servicio
60"
Motor
Motor
Motor
Acceso
Acceso
para
14" x 4"
14" x 4"
para
14" x 4"
Servicio
Servicio
27-1/4"
35"
27-1/4"
35"
27-1/4"
35"
27-1/4"
35"
44"
27-1/4"
27-1/4"
46"
46"
46"
35"
44"
35"
44"
- 2" x 4" MURO
- 2" x 4" MURO
- 2" x 4" MURO
- CAJA DE CONEXCIONES
(Mano derecha (como mostrado) solamente)
TARA™, Mano Izquierda
TARA™, Mano Derecha
TARA™ CON FALDÓN INTEGRADO
NOTA: 1. Las dimensiones en general son nominales con una tolerancia de +0 y -1/4 pulgadas (6,4 mm).
2. Mantenga las dimensiones del acceso dadas son tamaño mínimo. El acceso del servicio se requiere todavía para las
unidades que no tienen el Bomba/Motor pre-instalado.
3. Las medidas dentro de cada unidad representan el recorte en piso para permitir desagüe/rebosadero.
4. Todas las medidas están en pulgadas. Para convertir a los milímetros, multiplique las pulgadas por 25.4.
5. No todas unidades de exportación vienen con el Bomba/Motor pre-instalado.
RECORTE
DIAGRAMA EN PLANTA DE TINAS DE ESQUINA
3" ESQUINAS
DEL RADIO
(5 lugares)
58"
58"
(1473 mm)
(1473 mm)
58"
58"
(1473 mm)
(1473 mm)
59"
Ref.
57"
Desagüe
Ref.
Motor
Rebosadero
Desagüe
Rebosadero
90˚
25-1/2"
90˚
90˚
90˚
25-1/2"
(648 mm)
(648 mm)
22-5/8"
(575 mm)
45-9/16"
22-5/8"
(575 mm)
50"
(1157 mm)
(1270 mm)
CAPELLA 60 &
CAPELLA 60 MOTOR/BOMBA DELANTERO IZQUIERDO
(Posición de motor/Bomba no mostrada.)
GALLERY DE ESQUINA RECORTE
Mano Izquierda
3" ESQUINAS
DEL RADIO
(5 lugares)
58"
(1473 mm)
58"
(1473 mm)
58"
58"
59"
Ref.
(1473 mm)
(1473 mm)
Motor
57"
Desagüe
Ref.
Rebosadero
90˚
Motor
90˚
Desagüe
Rebosadero
90˚
90˚
25-1/2"
(648 mm)
25-1/2"
(648 mm)
22-5/8"
(575 mm)
)
m
45-9/16"
(1157 mm)
22-5/8"
(575 m
50"
(1270 mm)
TARA DE ESQUINA RECORTE
Mano Derecha
GALLERY DE ESQUINA RECORTE
Mano Derecha
58"
(1473 mm)
58"
(1473 mm)
59"
Ref.
Motor
Desagüe
Rebosadero
90˚
90˚
25-1/2"
(648 mm)
25-1/2"
(648 mm)
45-9/16"
(1157 mm)
TARA DE ESQUINA RECORTE
Mano Izquierda
17
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES DE INSTALACÍON
Estructura y Soporte
La instalación del desagüe y el rebosadero se extiende por debajo de la parte inferior de la tina. Cabe señalar que para esto se requiere
hacer un corte en el piso.
La estructura del piso, debajo de la tina, debe poder soportar el peso total de la tina, el agua, y el ocupante. Referirse al cuadro
correspondiente al peso total de su modelo. La unidad tiene que estar soportada por la parte inferior de la tina y no del borde de la tina o
de la pestaña. Si el subfloor es plano y una superficie continua, ninguna otra preparación es necesaria. Ud. puede continuar con la instalación
de la tina. Si el subsuelo no está nivelado, Ud. tiene que nivelar toda la superficie antes de instalar la tina. El uso de materiales que rellenan
o permiten una instalación a nivel, son permitidos siempre y cuando el método que se use, garantice una tina nivelada, que esté sujetada por
debajo. Las materias que se pueden utilizar son un piso que nivela compuesto, el mortero, el yeso o la expansión mínima espuma estructural
que tiene una densidad de un mínimo de 5 lbs. /pies cúbicos; sin embargo el baño debe quedarse el nivel en la orden para lo desaguar
apropiadamente y todos pies de espuma deben hacer el contacto repleto con la materia que nivela. Ambos lados de la junta o empalmes del
subsuelo deben estar nivelados. Cuando fije las tinas al muro utilizando pestañas, use planchas de relleno para rellenar cualquier
espacio entre las pestañas de la tino y el muro.
El borde de la tina no está hecho para soportar peso. Si el material de recubrimiento va a estar en contacto con la tina o sobrepuesto, el
peso adicional no debe recaer sobre ella.
El plastico protector debe permanecer dentro de la tina durante la instalación. Antes de la instalación remueva el plastico, inspeccionne
que la tina no tenga algún daño o defecto, aplique el plastico de nuevo este proteje la superficie de daños como de zapatos, herramienta,
etc. Removerlo al final de la instalación y limpieza final.
Importante: Si se ha de utilizar un faldón, éste deberá instalarse cuando se está instalando la unidad - Refiérase a las instrucciones
de instalacíon de faldón. Cuando se haya completado todo la instalación, instale las partes opcionales de las vestiduras.
INSTALACIONES TÍPICAS
MOTERO O PEGAZULEJOS
MOTERO O PEGAZULEJOS
RECUBRIMIENTO
FINAL
AZULEJO
AZULEJO
RELLENO
DE ESTUCO
MOTERO
PANEL DE
CEMENTO
SELLAD
TAPAJUNTAS
SELLADOR
PESTAÑA
BORDE DE LA
TINA
CLAVO O
TORNILLO
BASE
SELLODOR
DE SILICONA
TAPAJUNTAS
MURO
1" X 4"
(NO PARA CARGA)
1" X 4" (NO PARA CARGA)
1" X 4" (NO PARA CARGA)
AL RAS DEL MURO
PAQUETE OPCIONAL DE PESTAÑA
SEMIEMPOTRADA
NOTA: EN el Riva 5 y Riva 6, la instalación de cañerías de la descarga extiende levemente más allá del borde de baño. Al instalar cualquier
baño como semi-fregadero, baja el lado bomba/motriz en primero en el recorte.
DETALLE DEL MONTAJE DE PESTAÑA TIPICO
AZULEJO
PANEL
AZULEJO
MURO
MURO
PANEL
DE CEMENTO
DE CEMENTO
IMPERMEABILIZANTE
IMPERMEABILIZANTE
PEGAZULEJOS
PEGAZULEJOS
PESTAÑA
FIJA CON
TORNILLOS
PROVEÍDOS
FIJA CON
TORNILLOS
PROVEÍDOS
PESTAÑA
SI ES
SI ES
NECESARIO,
USE
PLANCHAS DE
RELLENO PAR
RELLENAR EL
ESPACIO
ENTRE
EL MURO
Y LA PESTAÑA
NECESARIO,
USE
PLANCHAS DE
RELLENO PAR
RELLENAR EL
ESPACIO
ENTRE
EL MURO
Y LA PESTAÑA
MURO
MURO
JUNT A DE
1/8 PULGADAS
JUNT A DE
1/8 PULGADAS
PESTAÑA
1"X 4"
PESTAÑA
(NO PARA
CARGA)
OPCIONES de INSTALACION de UNDERMOUNT
El undermount da la oportunidad de ser flexible en el diseño y la ubicación del baño. Los ejemplos se muestran para instalaciones
posibles. Refiérase a páginas 23-24 para instrucciones de instalación de undermount.
RINCON
LIBERTE la POSICION
18
NICHO
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES DE INSTALACÍON
FALDÓN
Tinas de Esquina con Faldón
Si se usa faldón en la tina de esquina, es necesario contar con
mayor soporte en la parte frontal de la unidad. Mida la altura del piso
a laparte inferior del borde de la tina. Corte dos muros de 2 x 4
pulgadas, aplique el pegazulejos en ambos extremos e instale (Véase
las especificaciones en la REFERENCIA de ROUGHING-IN (ES-
QUINA)).
DETALLE DEL MONTAJE
CON FALDÓN INTEGRADO
RECUMBRIMIENTOS
SOPORTE PARA TINAS DE ESQUINA
GOTA DE IMPERMEABILIZANTE
APLIQUE EL
PEGAZULEJOS
H
FALDÓN
2" x 4" MURO
Entrepaño movible de Falda
Eliminación e Instalación
Resbale los clips sobre el labio inferior de la abertura de la falda
e incline para arriba hasta que las lengüetas del Velcro hacen el
contacto.
DETALLE DEL MONTAJE CON FALDÓN EN "U"
RECUBRIMENTOS
GRAPA EN EL CENTRO DE
LA PARTE INFERIOR DEL
BORDE DE LA TINA
RELLENO (Opcional)
GOTA DE
IMPERMEABILIZANTE
FALDÓN
PELE ATRAS RINCON
PARA EMPEZAR DESCONECTAR
DUAL LOCK™ CIERRE
MARCO DEL
FALDÓN
FIJE LA PARTE INFERIOR DEL MARCO AL PISO
19
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES DE INSTALACÍON
Acceso para Servicio
Acceso Faldón Integrado
En este caso se tiene acceso a las instalaciones por los paneles
removibles del faldón.
En el caso de instalaciones parcial o totalmente empotradas,
deje un acceso a las conexiones. Es responsabilidad del instalador
dejar espacio suficiente para el registro. Las medidas mínimas re-
comendables para el registro de la tina se muestran en la ilustración
que lleva el nombre de “Registros”.
ACCESOPARA SERVICIO (CON FALDÓN INTEGRADO)
Provee área adequada al rededor de la tina para circulación de
aire para enfriamiento del motor y para proveir aire suficiente a los
chorros. No ponga aislamiento en este área o al rededor del motor.
Acceso opcional de Servicio de
RapidHeatTM
Donde tinas se han ordenado con la calentadora opcional de
RapidHeatTM considera un acceso adicional del servicio.
Si el acceso del servicio no se ha proporcionado, es la res-
ponsabilidad de propietarios para quitar el baño y proporcionar
el acceso requerido, debe una reparación llega a ser necesario.
PANELES
REMOVIBLES
ÁREA DEL REGISTRO
MOTOR
Acceso con Faldón
REGISTROS (SIN FALDÓN)
Se puede colocar un faldón opcionál a lo largo de la tina para
cubrir las instalaciones sobre el nivel del piso y usarlo también como
acceso para dar servicio a las instalaciones. Para poder retirar el
faldón, deje un espacio de por lo menos 8 pulgadas con respecto a
la tina.
MOTOR
El diseño del faldón permite colocarlo al ras del suelo cubriendo
hasta 1-1/4 pulgadas (31,75 mm) de la orilla de azulejos, linóleo u
otros recubrimientos utilizados en el piso.
El faldón opcionál incluye instrucciones de instalación más deta-
lladas.
12"
FRENTE
ACCESO PARA SERVICIO (TINAS DE ESQUINA)
18"
12"
REGISTRO
ALTERNO
REGISTRO
IDÓNEO
18"
En algunos casos, puede que no se haya proporcionado acceso
debido al diseño de la tina y teniendo completo entendimiento de
que en este caso, pueda que sea necesario retirar la unidad para
obtener servicio.
Si así fuera el caso, no será posible diagnosticar un problema
sin tener completo acceso al sistema de plomería. Esto requiere
remover la unidad completa. A pesar de que esta práctica no es
implementada comunmente, es un método aceptable.
20"
B
18"
C
A
36"
24"
UNIDAD DERECHA
ACCESO PARASERVICIO
A - Acceso preferidio
B - Alternativa aceptable si el acceso A no es posible
C - Registro para equipo accesorio adicional (Opcionál)
NOTA: El registro de las unidades izquierdas
se coloca en el lado opuesto (en imagen de espejo).
A C C E S O P A R A S E R V I C I O
(BG55, CAPELLA 60 TINAS IZQUIERDO DELANTERO DE LA ESQUINA DEL
MOTOR SOLAMENTE)
AREA
A
FRENTE
AREA
B
MOTOR
En algunos casos el acceso puede haber proveído en el Area A,
pero el servicio es requerido en el Area B, lo que reuquiere que la
unidad sea removida para obtener servicio y luego ser reinstalada.
Si no se ha proporcionado un acceso para obtener servicio,
es la responsabilidad del dueño de la casa el remover la tina y
proporcionar el acceso requerido, en caso de necesitarse repa-
ración de la unidad.
12"
18"
Área de acceso preferida
20
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES DE INSTALACÍON
CONEXIÓN ELÉCTRICA (PARA TINES DE ESQUINA)
Conexiones Eléctricas
CLAVIJA
TRIFÁSICA DE CAJA
DE CONTROL
Se requiere un circuito independiente protegido con un
interruptor de circuito para fallas a tierra (GFCI). Instale un
contacto dúplex en el muro debajo de la tina, por lo menos 4
pulgadas arriba del piso. No se incluye el contacto dúplex
porque están fabricadas con un seguro y cómodo interruptor
ON/OFF de control electrónico.
CUERDA MOTRIZ DEL PODER
DE CONTROLAR CAJA
CONTACTO GFCI
DÚPLEX*
4" (10,6 cm)
MÍNIMO O DE
ACUERDO
CON EL
PELIGRO: RIESGO DE DESCARGA ELÉCTRICA. Conec-
te la unidad solamente a un circuito protegido con un
GFCI.
EDIFICIO
LOCAL O
CÓDIGOS
PRECAUCIÓN: El motor o la bomba pueden sufrir fugas
y daños permanentes si se operan sin agua suficiente
en la tina. Antes de aplicar la energía eléctrica a la insta-
lación, asegúrese de que el interruptor esté en la posi-
ción “OFF” para evitar que se dañe la bomba.
PISO
*(NO SE INCLUYE)
NOTA: Las unidades de la exportación pueden o no pue-
den venir con motriz/bomba o pueden venir con especifica-
ciones motrices diferentes de lo que es especificado aquí. En
cada caso consulta con un contratista y el electricista licen-
ciados antes de instalar la alimentación o conectar la unidad.
Jacuzzi Whirlpool Bath no hace los reclamos a la compa-
tibilidad ni la oportunidad eléctricas de doméstico ni las uni-
dades de la exportación y no es responsable de ningún de-
fecto ni los fracasos que se pudiera haber descubierto, po-
día haber sido reparado, o pudiera haber sido evitado si-
guiendo el edificio y códigos aplicable eléctricos locales.
Opcional RapidHeatTM
Conexión Eléctrica
NOTA: Las unidades de la exportación pueden o no pue-
den venir con motor/bomba pre-instalados o pueden venir
con especificaciones motrices diferentes de lo que es espe-
cificado aquí. En cada caso consulta con un contratista de
licenced y electricista antes de instalar la alimentación o co-
nectar la unidad.
Antes de hacer la conexión eléctrica, inspeccione la pla-
ca de indentificación del calentador para determinar si es
una unidad de 120 VAC o de 240 VAC.
Con los baños hidroterapeúticos Capella 55 con falda
integra, Capella 60 con falda integra, Capella Spacesaver
con falda integra, y Tara con falda integra, se provée una caja
de conexciones. Para obtener acceso at esta conexcion,
quite el panel de acceso de la falda. Véa los dibujos desde
encima para localizar la caja de conexciones.
Instale un rompecircuito o disyuntor separado de 120 VAC
15 AMP, o de 240 VAC 15 AMP (unidad de 240 VAC non
disponible en U.S.A.), para tener un circuito dedicado con
protección de fallas a tierra (GFCI). Use un alambre sólido
de cobre, calibre #8, para conectar la caja metálica del ca-
lentador al panel eléctrico de la casa o a una conexión local
aprobada. El calentador está provisto con un terminal de
conexión de tierra.
Cuando vaya a operar el calentador por primera vez, y
antes de cada uso de ahí en adelante, oprima el botón GFCI
con la energía eléctrica encendida (ON). El botón de reposi-
ción debe saltar hacia afuera. Oprima este botón para
reposicionar el interruptor. Si el interruptor falla en su funcio-
namiento de la forma indicada, es porque hay alguna co-
rriente de tierra circulando o el dispositivo está defectuoso,
lo que indica la posibilidad de un choque eléctrico. Apague
la energía eléctrica y no use el baño hasta que la causa
del problema haya sido identificada y corregida.
Una toma de electricidad separada y protegida por GFCI
es requerida (y no proveída) para la bomba/el motor. Hay
que instalar esta toma en la caja de conexciones. Esta caja
requiere una conexción eléctrica permanente. El motor es
pegado a la caja de conexciones en la fábrica.
CAPELLA 55 CON FALDÓN, CAPELLA 60 CON FALDÓN,
CAPELLA SPACESAVER CON FALDÓN, &
TARA CON FALDÓN - CAJA DE CONEXCIONES
FRIJANDO A LA BOMBA/MOTOR
GFCI
(NO
PROPORCIONADO)
CONEXIÓN ELÉCTRICA RAPIDHEAT™
CUERDA ELÉCTRICA
AL MOTOR
J-BOX PROPORCIONADO
ACCIONE CUERDA DE LA
CAJA DEL CONTROL
CONEXIÓN ELÉCTRICA
(PARA TINAS CON DRENAJE LATERAL O EN FRENTE)
CLAVIJA
TRIFÁSICA DE CAJA
DE CONTROL
CONTACTO GFCI
DÚPLEX*
4" (10,6 cm) MÍNIMO
CIRCUITOS SEPARADOS
O DE ACUERDO
CON EL EDIFICIO
LOCAL O
CON PROTECCIÓN
M
T
DE FALLA A TIERRA (GFCI)
CÓDIGOS
ELÉCTRIOS
*(NO SE INCLUYE)
CALENTADOR
21
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES DE INSTALACÍON
Plomería y Suministro de Agua
Información Sobre el Drenaje
Debe instalarse una unidad de drenaje/rebosadero (se vende separado) en la tina, verificar que no presente fugas y conectarse al sistema
sanitario de la casa. Después de abrir la caja de cartón, verifique que no hay daños y revise el acabado. En la unidad de drenaje/rebosadero
de Jacuzzi Whirlpool Bath, la pestaña, el filtro, la placa protectora de rebose y los tornillos de la placa vienen en un paquete por separado para
proteger el terminado. Siga las instrucciones de instalación incluidas en su unidad de drenaje/rebosadero.
Después de haberse instalado todo el drenaje, revise si éste está funcionando adecuadamente. Si la unidad no drena adecuadamente,
rectifique esta condición antes de proceder con la instalación. Jacuzzi Whirlpool Bath no es responsable por gastos de remoción o reinstala-
ción de las tinas.
NOTA: Es responsabilidad del instalador que las conexiones no presenten fugas. La garantía de Jacuzzi Whirlpool Bath de este
producto no cubre fugas en el drenaje.
Plomería
La bomba, los chorros y los dispositivos de succión para el sistema hidroterapeútico se aploman en la fábrica en tubería de PVC clasificación 40.
Todos los productos Jacuzzi Whirlpool Bath se prueban en la fábrica antes de embarcarse para verificar que funcionen correctamente y que
las conexiones no tengan fugas. Si detecta fugas, consulte Jacuzzi Whirlpool Bath y no instale la unidad.
Suministro de Agua
Pregunte a las autoridades locales cuáles son los requisitos que debe cumplir la instalación de plomería de acuerdo con la zona en que va
a instalarse la unidad.
IMPORTANTE: Es responsabilidad del instalador colocar correctamente la plomería del surtidor de llenado y cumplir con las normas
correspondientes. Jacuzzi Whirlpool Bath no garantiza las conexiones del suministro de agua, de la tubería, de los sistemas de
llenado o de desagüe. Tampoco es responsable de los daños sufridos por la tina durante la instalación.
PRECAUCIÓN: Para que la tina no sufra daños durante los trabajos de soldadura, coloque una barrera protectora anti-inflamable.
Limpieza Después de la Instalación
Para evitar que la superficie de la tina se raye o pierda brillo, no use limpiadores abrasivos, sino detergentes líquidos suaves.
Retire los residuos de estuco con una pieza de madera o plástico. Las herramientas de metal rayan la superficie. Las manchas producidas
por el estuco o el mortero pueden eliminarse frotando suavemente la superficie con un trozo de tela o una esponja con detergente.
Las manchas de pintura, alquitrán y otras manchas difíciles de sacar se pueden limpiar con diluyente, aguarrás o alcohol isopropílico
(alcohol de frotación). NOTA: Utilice estos productos químicos sólo para quitar las manchas de la SUPERFICIE.
Los rayones menos profundos que no alteran el acabado de color se pueden quitar con papel de lija húmedo o seco grano 600. Puede
recuperar el acabado brilloso de la superficie de acrílico de la tina con el compuesto especial Mirror Glaze #10 de Meguiar. Si no, utilice un
compuesto de frotación para automóviles y luego aplique cera en pasta para automóviles.
Será necesario volver a aplicar el terminado de la tina si las rayaduras y estrías son tan profundas que penetran la superficie acrílica. Pida
Jacuzzi Whirlpool Bath un folleto de instrucciones. Para obtener una lista de agentes de servicios, visite nuestra pagina web, http://
Las Reparaciones eléctricas o Mecánicas visitan http://jacuzzi.com/pdf/ASA.PDF
El fin, la Superficie, o las Reparaciones de Esqueleto-Relacionó visitan http://jacuzzi.com/pdf/AFC.PDF
La reparación Despide o los Accesorios visitan http://jacuzzi.com/pdf/MPD.PDF
22
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES de INSTALACION de UNDERMOUNT
MOSTRADOR
Instalación
Unainstalacióntípicatendráestascaracterísticasdela
construcción.
TODOS PIES de la ESPUMA DEBEN ESTAR EN el CONTACTO CON PISO PLANO
Protección de Unidad
Si la película protectora se ha quitado, reaplique película. Para la protección agregada, coloque una tela de gota u
otra materia en el fondo del baño para la protección. Tenga cuidado para no rasguñar la superficie del baño.
Preparación Contraria
NOTA: En el lado bomba/motriz del baño, el mostrador debe extender un mínimo de 4 (10,2 cm) pulgas pasada la
orilla exterior del baño, para vaciar el extender bomba/motriz de instalación de cañerías más allá del borde del baño.
MOTRIZ/BOMBA
La ORILLA INTERIOR
MOSTRADOR
DE BORDE
Posicione la plantilla para que el óvalo de recorte alinee
con la orilla de borde.
TACHONE PARED
PLANTILLA
B
A
C
BORDE de BAÑO
En esta posición, utilizando un lápiz de grasa, la marca
enelbañolasposicionescentralesdelalíneaporelcorte
fuera ranuras. Quite plantilla. La medida de líneas cen-
trales marcadas a un punto fijo tal como una pared.
D
MIDA DE MARCAS
de LINEA CENTRAL
A la PARED
Transfiera estas medidas para contradecir y marcar las posiciones centrales de líneas. La plantilla de la posición y
el corte contra para la desviación deseada.
B
A
MOSTRADOR
MOSTRADOR
C
PLANTILLA
BORDE de BAÑO
BORDE de BAÑO
D
OFFSET
MOSTRADOR
Después que cortar es completo, realiza cualquier dirigir necesitado, el trabajo de la orilla o el pulido al mostrador.
23
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES de INSTALACION de UNDERMOUNT
MOSTRADOR
Posicione el mostrador encima del baño para asegurar
el ataque y la apariencia correctos. La marca cualquier
ajuste que puede ser necesario. Quite el mostrador.
BAÑO
Que Adhiere Contra al Baño
APLIQUE SILICONA SELLADOR
para SOBREPASAR
DE BORDE de BAÑO
Limpie cualquier tierra o los escombros del borde del
baño. No utilice la tintorería abrasivo.
Dónde el mostrador hará el contacto con la cima del
bordedelbaño,aplicaunacuentadeselladordesilicona.
CUIDADO: no utiliza un adhesivo ni sellador adhesi-
vo para asegurar el mostrador al borde del baño. Si
la conservación o modelar de nuevo se requieren el
mostrador quizás se tenga que quitar. El adhesivo
vinculará permanentemente el mostrador al baño.
Esto hará la eliminación difícil y costosa y puede
causar el daño al mostrador o el baño.
MOSTRADOR
Posicione con cuidado el mostrador en el borde del
baño. El mostrador necesitará ser tenido en el lugar
mientras el sellador cura. Siga las instrucciones del
fabricante para determinar tiempo requerido para curar.
BAÑO
Aplique una cuenta continua de sellador de silicona
alrededor de la costura entera entre el borde de mostra-
dor y baño. Permita sellador para pelar sobre o el
curación antes de limpiar el mostrador o el baño.
APLIQUE SILICONA SELLADOR
PESAS
24
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES OPERADORAS
OPERACIÓN
NOTA: Estas instrucciones se aplican a todos los productos para baño fabricados por Jacuzzi Whirlpool Bath. No todas las
características descritas en el folleto de instrucciones se aplican a todas las tinas.
Todas las tinas fabricadas por Jacuzzi Whirlpool Bath están diseñadas para “llenarse y vaciarse,” lo que significa que la tina debe vaciarse
después de usarse y que la siguiente persona que la utilice deberá llenarla con agua limpia. Ésta es una medida de higiene, ya que estas tinas
no están diseñadas para estar llenas de agua constantemente como una alberca o una tina de exteriores. Si usted quiere una unidad diseñada
para sostener continuamente el agua, póngase en contacto con su distribuidor de Remolino de Jacuzzi para la línea completa de unidades de
remolino disponibles.
Una vez instalada la tina, retire cualquier residuo o material extraño que haya quedado de la construcción. Use trementina o diluyente para
eliminar manchas y residuos difíciles de pintura o alquitrán. Otros tipos de residuos pueden eliminarse con un trozo de tela humedecido con
detergente líquido. Frote ligeramente la superficie con una pieza de madera o plástico para retirar los residuos de estuco; no use lijas
metálicas, cepillos de alambre u otras herramientas de metal porque dañarán la superficie de la tina.
Nivel del Agua
Cierre el desaguadero y llene el baño hasta que agua sea por lo menos 1 a 2 pulgas encima del chorro más alto (ve línea de flotación
indicada en la ilustración). No prenda el sistema de remolino en tiempo si los chorros no se sumergen completamente en el agua. No
sumerja el tablero de control saturando el baño. Correr el sistema de remolino cuando hay agua insuficiente en el baño podría tener como
resultado rociar de agua fuera del área del baño. Correr el sistema de remolino sin agua dañará la bomba que recircula.
No sumerja el tablero de control saturando el baño.
Las unidades del constructor/consuelo del Jacuzzi vienen equi-
pado con controles electrónicos. Refiérase a las instrucciones Elec-
trónicas de Controles en la próxima página.
LLENE HASTA QUE EL NIVEL
DE AGUA LLEGUE POR LO MENOS
1-2PULG. ARRIBA DEL CHORRO MÁS ALTO.
ACCESORIOS TÍPICOS PARA TINAS
INTERRUPTOR DE
CONTROL ELECTRÓNICO
1-2"
CHORROS REGULABLES
PLACA
PROTECTORA
DE SUCCIÓN
(Opcional) RapidHeatTM
Operación
CASCADA DE LLENDO
(OPCIONAL)
Una vez que el calentador esté instalado y la bomba de circula-
ción de agua en remolino esté funcionando, la operación del calen-
tador es completamente automática. El calentador ayudará a man-
tener la temperatura del agua de baño.
DRENJA/REBOSADERO
(OPCIONAL)
Interruptor del Vacío
El calentador está equipado con un interruptor preajustado de
vacío que no permitirá que el calentador se encienda (ON) si la bomba
no está funcionando con el agua fluyendo a través del sistema.
Las unidades de la exportación vienen equipado con el interrup-
tor Mágico de EN/DE de Remolino de Toque. Refiérase al Toque
Mágico® las instrucciones de Interruptor de Remolino en la próxima
página.
ACCESORIOS TÍPICOS PARA TINAS
Interruptor de Límite Alto
INTERRUPTOR NEUMÁTICO
El calentador incluye un interriptor exclusivo de límite alto. Este
ciricuito de seguridad no se accionará falsamente por el agua ca-
liente de la tubería de la casa. Su única función es apagar el calen-
tador si falla el termostato. Si el alto-límite tropieza con frecuencia,
contacta a su Proveedor de Internet Eléctrico/Mecánico Autorizado.
un Proveedor de Internet.
ON/OFF MAGIC TOUCH
CONTROLES DE AIRE
CHORROS REGULABLES
PLACA
PROTECTORA
DE SUCCIÓN
REPOSICIÓN DE
LÍMITE ALTO
CALENTADOR
ENCENDIDO (ON)
HEATER ON
OVER HEAT
PROTECTION
PUSH TO RESET
CASCADA DE LLENDO
(OPCIONAL)
DRENJA/REBOSADERO
(OPCIONAL)
25
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES OPERADORAS
Interruptor Neumático Magic Touch®
El interruptor neumático ON/OFF Magic Touch, ubicado en una
posición muy cómoda en la tina, le permite activar el sistema
hidroterapeútico mientras se baña. Sólo oprima el botón del inte-
rruptor; para apagarlo, oprímalo nuevamente.
Si su tina cuenta con un cronómetro de pared Jacuzzi Whirlpool
Bath©, prográmelo el tiempo que desee operar el sistema
hidroterapeútico. Nota: Cuando quiera que funcione sólo 10 minu-
tos, haga girar el cronómetro a la derecha hasta pasar el número 10
y regréselo al número deseado. Si el sistema hidroterapéutico no se
activa habiendo programado correctamente el cronómetro, será
necesario oprimir el botón del interruptor Magic Touch.
Interruptor De Control Electrónico
El interruptor ON/OFF del control electrónico, establecido con-
venientemente en el baño, permite que usted dé vuelta al sistema
del torbellino por intervalos mientras que en el baño. Empuje sim-
plemente abajo en el botón del interruptor a giran el sistema del
torbellino. Para dar vuelta al sistema apagado, empuje hacia abajo
en el botón otra vez.
El interruptor de control electrónico apagará automáticamente
después de 20 minutos. Empuje hacia abajo en el botón del inte-
rruptor para recomenzar el sistema del torbellino otra vez
INTERRUPTOR MAGIC TOUCH
L
P
O
R
I
O
H
L
W
ON/OFF
OPRIMAEL CENTRO ON/OFF
CómoControlarelSistemaHidroterapeútico
El funcionamiento del sistema hidroterapeútico de la tina lo de-
terminan tres factores: dirección del flujo, fuerza del agua y fuerza
del aire. Todas las tinas fabricadas por Jacuzzi Whirlpool Bath están
equipadas con chorros regulables PowerPro®, que pueden ajustar-
se con respecto a esos tres factores. Algunas tinas cuentan con
chorros regulables sólo en cuanto a dirección y flujo del aire.
CHORROS
REGULABLES
DIRIGIBLES
Instrucción: Para cambiar la dirección del flujo del agua, haga
girar la boquilla del chorro hacia el ángulo deseado. Los chorros
pueden dirigirse en forma independiente hacia cualquier parte del
cuerpo y también pueden regularse para que apunten en la misma
dirección (hacia la izquierda o hacia la derecha) a fin de mover el
agua en forma circular para crear un efecto de remolino.
Fuerza del agua: Los chorros de alto volumen regulables pue-
den ajustarse para controlar la fuerza del agua que cae a la tina.
Para incrementar la fuerza haga girar a la izquierda los controles de
los chorros; para reducirla, hágalos girar a la derecha. Nunca acti-
ve el sistema hidroterapéutico si los chorros están cerrados.
Fuerza del aire: La intensidad de la acción del torbellino del
hydromassage es determinada por la cantidad de aire instalada en
el agua. En el Toque Mágico® controla sistema sólo: La abertura los
jets permite completamente una cantidad igual de aire instalada en
el agua. Disminuya el flujo de aire en unos o más jets para aumentar
el flujo de aire para los jets restantes. Nunca active el sistema
hidroterapéutico si los chorros están cerrados.
Los controles sólo de Magic Touch®
CONTROLES PARA INDUCCIÓN DE AGUA
GIRE A LA
DERECHA PARA
DISMINUIR EL
FLUJO DE AIRE
GIRE A LA ISQUIERDA
PARAINCREMENTAR EL
FLUJO DE AIRE
26
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES de CONSERVACION
Cómo Limpiar la Tina
Aditivos de Baño
Para limpiar la tina sólo use detergentes líquidos suaves, no
abrasivos. Puede proteger y recuperar el brillo de la superficie acrílica
aplicando terminados una cera acrílica de igual calidad o cera para
pulir automóviles.
NOTA: NO UTILIZA ADITIVOS DE BAÑO CON BASE ACEITOSA.
Si Ud. desea utilizar cualquier clase de aditivo en el baño, utilice
solamente una pequeña cantidad de polvo o substancia cristalina
de poca espuma, la acción de remolino intensifica las propiedades
de hacer espuma de los jabones.
Nunca use limpiadores abrasivos para el hogar en ningún
producto Jacuzzi Whirlpool Bath.
El uso de ciertos aceites de baño, baños de burbujas y aditivos
de baño pueden incrementar el nivel de acumulación de residuos
en el sistema de tinas de hidromasaje. Si los excesos de acumula-
ciones persisten, Ud. debe dejar de seguir usando estos productos.
Reparaciones de la Superficie
Será necesario volver a aplicar el terminado de la tina si las
rayaduras y estrías son tan profundas que penetran en la superficie
acrílica. Pida a su distribuidor autorizado Jacuzzi Whirlpool Bath ins-
trucciones especiales.
Placa Protectora de Succión/Mantenimien-
to del Filtro
Elimine los residuos de cabello y mugre acumulados en la placa
protectora de succión y en el filtro cuando sea necesario. Para ello,
retire el tornillo central y desmonte la placa cuadrada. Limpie los
orificios de la placa con una descarga de agua. Cuando la reinstale
oriente la placa y el filtro con la pequeña muesca en la parte inferior.
El empaque debe insertarse en el surco de la placa/filtro antes de
reinstalar el accesorio de succión.
PRECAUCIÓN: Cuando esté encendido el sistema hidro-neu-
mático, mantenga el cabello alejado del accesorio de succión
aproximadamente 6 pulgadas (15,2 cm). El cabello largo hasta
los hombros debe llevarse recogido o cubierto con una gorra
de baño. No encienda el sistema hidroterapeútico si la placa
protectora no está en su lugar. Es un dispositivo de seguridad y
siempre debe estar bien colocado para reducir al mínimo el ries-
go de que el cabello o alguna parte del cuerpo queden atrapa-
dos.
Purificatión el Sistema de Tinas de
Hydromasaje
NOTA: EL SISTDEMA WHIRLPOOL DEBE PURIFICARSE POR LO
MENOS DOS VECES AL MES
Para eliminar los residuos de tina, acumulados en el sistema
hidromasaje, es recomendable limpiar el sistema de hidromasaje
por lo menos dos veces por semana. Sin embargo, para obtener
mejores resultados, le recomendamos que limpie su sistema des-
pués de cada uso, utilizando nuestro detergente exclusivo de dos
partes, fabricado especialmente para baños hidromasajes.
“Systems Clean™” está disponible mediante nuestros Distribui-
dores autorizados de baños Jacuzzi Whirlpool o llamándonos direc-
tamente al 1-800-288- 4002.
Instrucciones para el uso Systems Clean™:
CUIDADO: ¡No UTILICE AL BAÑARse! ¡UTILICE el CUIDADO EX-
TREMO AL MANEJAR ESTE PRODUCTO!
Inmediatamente después de bañar y salir la bañera de
hidromasaje, sale el agua del baño en la tina y agrega agua más
caliente. El nivel del agua en la tina debe ser por lo menos 2” (50.8
Mm) encima del chorro más alto. La NOTA: El aire iniciado del siste-
ma de hydromassage causará que los Sistemas Limpien™ el con-
tenido para espumar y aumentar el olor. Si su tina tiene los controles
aéreos, la vuelta LEJOS el control de aire de remolino o lo gira a la
colocación más baja y vierte en el contenido entero de PAQUETE
#1 SOLO directamente en el agua del baño. Para mejores resulta-
dos, vierta el Sistema Limpia en la tina cerca de la toma para la
bomba de la circulación y está seguro evitar el contacto con la piel.
Permita el remolino para correr para 30 segundos y entonces agre-
gar PAQUETE #2 SOLO. Es importante utilizar Paquete #1 antes
Paquete #2 en evitar un olor fuerte. Permita el baño para correr para
5 a 10 minutos entonces desagua la tina completamente. Rellene la
tina con agua fría y corra para 2 a 3 minutos. Desagüe completa-
mente y aclare de cualquier residuo.
PLACA PROTECTORA DE SUCCIÓN/FILTRO
FILTRO
A C C E S O R I O
DE SUCCIÓN
TORNILLO
EMPAQUE
MUESCA
PELIGRO: Perjudicial si tragado. Sustancia irritante de ojo. Pro-
teja sus ojos, membranas de piel y moco del contacto con este
producto o su solución concentrada. Un producto alcalino fuerte
puede causar las quemaduras severas a los ojos y pelar.
Si Ud. ha seguido las instrucciones de limpieza de norma men-
cionadas, y todavía tiene un exceso de residuos de baño acumula-
do y por lo tanto desea un mecanismo alternativo de limpieza, reco-
mendamos SUPER SYSTEMS CLEAN PLUS, manufacturado por
Stearns Packaging para rectificar esta situación. Este producto se
puede obtener contactándonos al 1-800-288-4002. Se recomienda
que Ud. siga las instrucciones del fabricante incluidas con el pro-
ducto. Pueda que sea necesario usar este producto repetidamente.
SUPER SYSTEMS CLEAN PLUS no reemplaza la necesidad de
limpiar el sistema periódicamente con Systems Clean, de acuerdo a
las recomendaciones dadas.
27
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Guía General de Reparo de Fallas Baños Hydroterapeúticos
PROBLEMA
PROBABLES CAUSAS
SOLUCIÓN
No llega corriente a la bomba/motor.
Reconecte el GFCI.
Bomba/Motor no arranca.
No está conectada la bomba/motor.
Meta tapón (tapones) completamente en
salida (salidas). Las unidades con con-
troles electrónicos: El motor tapa en la
caja del control y tapones de caja de con-
trol en el receptáculo de GFCI. Las uni-
dades con controles manuales: El motor
tapa en el receptáculo de GFCI.
Conecte de nuevo tubo al interruptor
El interruptor mágico del Toque - tubo Mágico del Toque o para ventilar el bom-
aéreo no conectó para cambiar ni venti- ba/motor de interruptor.
lar interruptor en el bomba/motor.
Reemplace el ensamblaje de la bomba/
motor.
Bomba/Motor defectuosa.
Bomba/Motor funciona, pero los jets de Los chorros de agua están cerrados.
agua no funcionan.
Abra los chorros de agua rotando a la iz-
quierda (contra el reloj).
La cobertura de succión puede estar blo- Con el motor desconectado, retire la tapa
queada.
de seguridad y quite toda basura. Vuel-
va a colocar la cobertura de succión
antes de volver a operar el equipo.
Bomba/Motor funviona, pero el aire no Las válvulas de aire están cerradas.
se inyecta al agua.
Abra las válvulas de control de aire.
El interruptor Magic Touch - tubo aéreo Conecte de nuevo tubo al interruptor
no conectó para cambiar ni ventilar inte- Magic Touch o para ventilar el bomba/
El bomba/motor hace no válvula.
rruptor en el bomba/motor.
motor de interruptor.
La cuerda motriz del poder no conectó Conecte de nuevo cuerda de poder de
para controlar caja. motor para controlar caja.
Si un reloj de pared se utiliza, el reloj es Reemplace el reloj.
defectuoso
Escape de agua en las uniones de la
bomba.
Muy ajustados, aro tórico mal acoplado Afloje los empalmes, revise y vuelva a
o mal colocado, mal ajustado.
colocar el aro tórico. Si el aro tórico ha
perdido su forma, reemplácelo (refiérase
al número de teléfono abajo). Cuando
ajuste las tuercas de empalme, hágalo
únicamente en forma manual.
Bomba/Motor se apaga por sí solo, o
mediante el cronómetro, antes del
tiempo fijado.
La protección termal del motor ha Deje enfriar el motor; la protección termal
desactivado la bomba/motor, debido a se volverá a conectar. Revise la existen-
sobrecalentamiento (suministro de voltaje cia de ventilación apropiada. (Revise el
bajo).
suministro de voltaje.)
GFCI desconectado.
Reconecte el GFCI. Si continua desco-
nectándose, no utilice este equipo. Des-
conecte el equipo y haga que el proble-
ma sea arreglado por un electricista au-
torizado, antes de volver a utilizarlo.
Consulte con un electricista autorizado
para corregir el cableado de la unidad.
Cable de alimentación inadecuado.
NOTA: Si el equipo está dentro del plazo de su garantía, contacte al Servicio de Apoyo de Jacuzzi Whirpool Bath al 1-(800)
288-4002, con el número de serie de la unidad antes de que se inicie el trabajo. El Número de serie se localiza en el Plato
del Número de serie de la Especificación. Vea página 30.
28
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
LAS ESPECIFICACIONES DEL PRODUCTO ESTÁN SUJETAS A CAMBIOS SIN PREVIA NOTIFICACIÓN
USE LAS INSTRUCCIONES DE INSTALACIÓN PORPORCIONADAS CON EL PRODUCTO.
Jacuzzi Whirlpool Bath ha obtenido las listas de códigos correspondientes (standards), para productos de este tipo, que
generalmente están a disposición por todo el país. Antes de instalar el producto, el instalador o dueño de éste tiene la obligación
de cumplir con el código específico local. Jacuzzi Whirlpool Bath no representa, ni garantiza, ni es responsable de hacer cumplir
cualiquiera de estos códigos de instalación.
Jacuzzi Luxury Bath
14525 Monte Vista Ave., Chino, CA 91710
Service Support: 1- (800) 288-4002
©2005 Jacuzzi Whirlpool Bath K272000AF 7/06
Fibras
Printed in the U.S.A.
reciclables
29
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICIOSAUTORIZADOS
Si usted necesita obtener información sobre una compañía de servicios en su cercanía, o necesita asistencia para
preguntas sobre la operación o mantenimiento del producto, por favor llame a nuestro Departamento de Servicios
deApoyo, teléfono 1-800-288-4002. Para obtener una lista de agentes de servicios, visite nuestra pagina web, http:/
Las Reparaciones eléctricas o Mecánicas visitan http://jacuzzi.com/pdf/ASA.PDF
El fin, la Superficie, o las Reparaciones de Esqueleto-Relacionó visitan http://jacuzzi.com/pdf/AFC.PDF
La reparación Despide o los Accesorios visitan http://jacuzzi.com/pdf/MPD.PDF
Cuando solicite servicios o asistencia técnica, por favor tenga a la mano tanto el modelo, como el número de serie
de la unidad. Esta información puede ser obtenida en la tarjeta de registro del producto, proporcionada junto con su
unidad. Si la tarjeta ha sido desplazada, esta información se podrá obtener en la etiqueta de especificaciones/
número de serie, colocada en la unidad misma (para la ubicación de esta etiqueta, ver a continuación).
PRODUCTOS PARA EL BAÑO
Baños Whirlpool: La etiqueta está colocada en la pared de la tina, cerca de la bomba/motor.
Baños empapados: La etiqueta se localiza junto a la capacidad rebosadero.
Etiqueta de Especificaciones/Número de Seri
Número de centro - Número de Seri
XXXX - XXXXXX
Las Especificaciones Eléctricas aplicables para su unidad.
MODEL # XXXXXXX
NAME XXXXX
COLOR XXXXX
MFG # XXXXX
SER # XXXXXX
LAS ESPECIFICACIONES
ELECTRICAS IMPRIMIERON
EN ESTA AREA
Usted encontrará
el número de serie aquí
THIS PRODUCT MEETS OR EXCEED
MADE IN
THE FOLLOWING STANDARDS
USA
BATH & SPA xxxx xxxx.x
SHOWER BASES xxxx xxxx.x
Apropie Logos de Conformidad de Seguridad para su unidad.
30
Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Garantía Limitada de Tinas de "Jacuzzi Whirlpool Bath"
Producto de Grupo de Tinas Builder/Comfort
COBERTURA DE LA GARANTÍA
Jacuzzi Whirlpool Bath ( la "Compañía") ofrece la siguiente garantía limitada expresa a los compradores originales de cualquier tina de Jacuzzi Whirlpool Bath
Builder/Comfort Group Bath Product ("unidad") que compren el producto para uso personal o de una sola familia ("usuario"). La Compañía se compromete a la
reparación o sustitución, según sea su decisión solamente, de la unidad o sus equipos, de conformidad con los siguientes términos y condiciones.
GARANTÍA LIMITADA DE DOS AÑOS EN LAS TINAS
Nuestra garantílimitada a en los productos de Builder/Comfort Group Bath es de dos (2) años. La garantía cubre a la unidad y a los componentes instalados de
fábrica (v.g. la bomba, el motor) en contra de cualquier defecto de material o de construcción. La cobertura de la garantía empieza el día que el usuario compró la
unidad.
GARANTÍA LIMITADA DE CINCO AÑOS (SOLAMENTE PARA LAS PIEZAS) POR LA BOMBA Y EL MOTOR
Nuestra garantía limitada por la bomba y el motor es por cinco (5) años, únicamente para las piezas. La cobertura de la garantía comienza en la fecha en la
que el usuario compró originalmente la unidad.
GARANTÍA LIMITADA DE NOVENTA DÍAS ( REPUESTOS ÚNICAMENTE) EN OPCIONES Y ACCESORIOS
Nuestra garantía limitada en las opciones y accesorios de los repuestos únicamente fabricados por la Compañía es de noventa (90) días. Nuestra garantía
cubre las opciones y accesorios fabricadas por la Compañía (v.g. juego de cascadas, vestiduras, faldas) en contra de cualquier defecto de material o de construc-
ción. La cobertura de la garantía empieza el día que el usuario compró la opción o accesorio.
LIMITACIONES DE LA GARANTÍA
Nuestra garantílimitada a no cubre los defectos, daños o fallas ocasionados por el distribuidor, instalador, o cualquier otra persona, ni los que resulten, sin
limitaciones, de cualquiera de los casos siguientes: descuido en el manejo (levantamiento de la unidad al usando la plomería como mango, abresión de los
terminados, etc.), modificación de cualquier tipo por cualquier razón (incluso modificaciones para cumplir con las normas de los códigos locales), instalación
inadecuada (incluso instalación no conforme a las instrucciones y especificaciones que acompañan a la unidad); conexiones proporcionadas por el instalador del
equipo; improprio abasto de voltaje o alguna modificación eléctrica no autorizada; mal uso; operación incorrecta; o falta de mantenimiento adecuado de rutina,
operación de la unidad sin la cantidad mínima de agua que se especifica o a una temperatura del agua inadecuada; uso de limpiadores abrasivos o improprios; o
desastres naturales como relámpagos, inundaciones, terremotos, etc.
Ademas, la COMPAÑÍA NO SERÁ RESPONSABLE POR DAÑOS INCIDENTALES O CONSECUENCIALES o pérdidas que se deriven de cualquier causa (v.g.,
daño del agua a las alffombras, techos, pérdida de uso, etc.) incluso su propia negligencia, daños a, relativos a, o que resulten de las partes cromadas cuando se
usen en la unidad sustancias químicas para piscina o "spa"; equipo opcionál de tina no fabricado por la Compañía pero provisto por el Distribuidor, instalador o por
la Compañía; el uso anterior de la unidad para hacer demostraciones, o defectos que debieran haberse descubierto antes de la instalación. Esta garantía limitada
no incluye: mano de obra, transporte, u otros costos en los que se incurra en la remoción y/o reinstalación de la unidad original y/o instalación de una unidad de
reemplazo; cualquier costo relativo a lograr el acceso para la reparación, o daño por pérdida de uso, incluso pérdida de ventas, utilidades o ventajas comercionales
de cualquier tipo en cualquier circunstancia. Las unidades quedan excluídas de cualquier cobertura de garantía en caso de que se le haya hecho a la unidad (o a
cualquiera de sus componentes) algún añadido, cancelación o modificaicón de cualquier tipo.
La cobertura de la garantía se proporciona únicamente en los Estados Unidos de América y Canadá.
EXCLUSIÓN DE GARANTÍAS IMPLÍCITAS
GARANTÍAS APLICABLES DE MERCANTIBILIDAD Y ADECUACIÓN PARA UN PROPÓSITO DETERMINADO SON NEGADAS TOTALMENTE O HASTA EL
LIMITE COMPLETO PERMITIDO CONFORME A LA LEY.
AVISO: Esta garantía le ofrece derechos legales concretos y es posible que además tenga usted otros derechos que varían de un estado a otro. No existen
garantías aplicables a los productos Jacuzzi Whirlpool Bath, excepto los que aquí se expresan o los implícitos en leyes estatales y federales aplicables. La
compañía no se hace responsable por declaraciones o interpretaciones que se hagan de cualquier forma y que resulten más amplias o que no correspondan con
la literatura autorizada que proporciona la Compañía.
Algunos estados no permiten limitaciones a la duración de una garantía implícita, o la exclusión o limitación de daños incidentales o consecuenciales, de tal
forma que las limitaciones o exclusiones antes descritas quizá no sean aplicables a usted.
RESPONSABILIDAD DE LA TARJETA DE GARANTÍA
La tarjeta anexa, que ya incluye la dirección de la Compañía, y que tiene por objeto el registro de la unidad para fines de garantía debe llenarse antes de
que hayan pasado (30) treinta días de la compra y enviarse a Jacuzzi Whirlpool Bath para que esta garantía entre en vigor.
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710
Download from Www.Somanuals.com. All Manuals Search And Download.
RESPONSABILIDAD DE TERCEROS
Es responsabilidad del instalador o del contratista constructor que actúen en nombre del usuario realizar una inspección de la unidad antes de
instalarla. Ellos son responsables de asegurarse de que la unidad no tiene defectos ni daños. Se ponen avisos en la unidad y en la caja que la contiene
para advertir al instalador sobre esta responsabilidad. En caso de que haya algún problema, no debe instalarse la unidad. La Compañía no se hace
responsable de fallas o daños que podrían haberse detectado, reparado o evitado mediante una inspección apropiada y pruebas antes de la instalación.
Cualquier daño que ocurra durante el trayecto es responsabilidad del transportista. El usuario o instalador DEBE abrir la caja y revisar que la unidad
no tenga ningún daño, al momento de la entrega. Si se encuentra algún daño, debe informarles de inmediato al vendedor y al transportista por escrito
y debe solicitarse una inspección. En caso de que el transportista no responda, debe avisarles al vendedor y al transportista. Los reclamos de flete
deben presentarse inmediatamente después.
Es responsabilidad del instalador, contratista constructor o usuario proporcionar acceso para servicio. La Compañía no es responsable por ningún
costo incurrido para obtener acceso para reparación. El usuario deberá afrontar con estos gastos y, si es apropiado, deberá recobrar este costo del
instalador.
Los daños que ocurran a la unidad durante su instalación son responsabilidad del instalador y/o del contratista constructor y daños que ocurran
después de la instalación de la unidad son responsabilidad del usuario.
Fallas en cualquier equipo opcional son responsabilidad única del fabricante del equipo. (Opciones y accesorios fabricadas por la Compañía tienen
garantía de noventa (90) días desde la fecha original de su compra para los repuestos únicamente).
El Distribuidor o Vendedor es responsable de conocer los requisitos de los códigos locales y de notificar al contratista instalador y o al usuario de
estos requisitos al momento de su compra. La Compañía no es responable por ningún costo incurrido en la modificación del producto para conseguir la
aprobación del código, a fin de obtener la aprobación municipal, estatal o del condado para el código en los E.E.U.U., o códigos municipales o provincialos
un Canadá.
SERVICIO DE GARANTÍA
Para beneficio del cliente, la Compañía tiene una lista de proveedores de servicio independientes que pueden realizar las reparaciones requeridas
para el servicio de garantía. Dichas empresas no son ni agentes ni representantes de la Compañía y no pueden obligar a la Compañía por palabra o
conducta.
La Compañía debe proporcionar el servicio de garantía que se describe arriba, cuando se hayan cumplido las siguientes condiciones: la falla es de
una naturaleza o de un tipo que queda cubierto por la garantía; el usuario le ha informado a un Agente autorizado o Representante del Departamento de
Garantías cuál es la naturaleza del problema durante el período cubierto por la garantía; el usuario le ha entregado a dicho agente o representante
pruebas irrefutables (v.g. pruebas de compra o instalación) de que la falla ocurrió o se descubrió dentro del período de garantía; una persona autorizada
de servicio independiente o representante de la Compañía ha tenido la oportunidad de inspeccionar la unidad durante horas hábiles regulares dentro de
un lapso razonable después de que el usuario reportó la falla.
A fin de obtener un servicio de garantía, consulte su directorio telefónico para encontrar al Agente de Servicio Autorizado de Jacuzzi Whirlpool Bath
que más cerca le quede. Describa su problema y el Agente de Servicio Autorizado inspeccionará la unidad y le ofrecerá el servicio que requiere la
garantía.
En caso de que no peuda ocnseguir a un Agente de Servicio Autorizado de Jacuzzi Whirlpool Bath, escriba o llame a:
Jacuzzi Luxury Bath
Warranty Service Department
14525 Monte Vista Avenue
Chino, CA 91710
Llame a : 1- (800) 288-4002
Para obtener un reemplazo según la garantía para componentes instalados de fábrica para opciones abastecidos por la Compañía y accesorios
fabricados y abastecidos por la Compañía, llame o escriba al domicilio que abajo se señala. Proporcione una descripción del problema y una prueba de
compra. Recibirá instrucciones de cómo obtener su reemplazo y de cómo devolver, a sus expensas, el o los componentes, opciones o accesorios
defectuosos.
Todas las partes, equipos y reparaciones asumirán el resto del lapso de garantía de la parte o partes reemplazados.
La obligación de garantía de la Compañía quedarán descargadas con la oferta de reemplazo o reparación. En caso de que el cliente se niegue a
aceptar la solución, se da por terminada la obligación de cumplimiento de garantía de la Compañía.
©2005 Jacuzzi Whirlpool Bath K272000AF 7/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Infinity Home Theater System HTS 20 User Manual
Jacuzzi Hot Tub DZ95 User Manual
John Deere Compact Loader 304J User Manual
Jonsered Brush Cutter GT2125L User Manual
Jonsered Lawn Mower LM2147 CM User Manual
JVC Speaker SP F508 User Manual
Kenwood Marine Radio TS 570D User Manual
KitchenAid Cooktop 8285418 User Manual
KitchenAid Ice Maker KUIS155HBL2 User Manual
KitchenAid Saw KSDG950E User Manual