R24/R30 Glasswasher
Maintenance Instructions
Heater Replacement
07610-003-12-39 A
September 23, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing upper (wash) strainer.
Reaching into the wash tank.
5. Using the 3/8” nutdriver, remove the nuts securing the heater
wires to the heater. Then carefully pull the wires out of the way.
7. Removing the heater may require that you reach into the wash
tank, grasp it and try give it a push out of the wash tank.
8. Once the heater is pushed away from the tank wall, pull it out
with your hands.
Removing the heater nuts.
Pulling the heater out.
Using the ratchet to remove the heater mounting nuts.
6. Next, use the ratchet and 1/2” socket to remove the heater
mounting nuts.
Removing the heater gasket
Heater Replacement Instructions
Revision A (09/23/2005)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Remove the old heater gasket and throw away.
10. Apply the new heater gasket.
AFTER MAINTENANCE ACTIONS
Service personnel may want to drain the machine and
allow it to cool down. Secure power to the unit at the service break-
er and then verify the torque of all fasteners covered in this instruc-
tion.
11. Take the new heater and slide it through the hole in the wash
tank and line it up so the wash tank studs fit in the holes on the
heater flange.
12. Place the mounting nuts and lockwashers on the studs and
secure them with the ratchet and 1/2” socket.
SPECIAL NOTES
13. Place the heater wires on the heater and tighten them down
using the 3/8” nutdriver.
Work performed on Jackson dishmachines by unautho-
rized or unqualified personnel may void the warranty. Before begin-
ning this or any other maintenance evolution on a unit under war-
14. Using the torgue wrench or a torque nutdriver (if available) ranty, you should contact a certified Jackson technician or Jackson
torge the nuts holding the wires, jumpers and bus bars to 16 in-lbs. Technical Service. You can find a list of qualified service agencies
in the back of you unit’s installation manual.
15. Ensuring that all non-essential personnel are clear of the area,
place the drain stopper back in the wash tank and restore power
and water to the unit. Turn the unit on and allow it to fill normally.
SPECIAL PARTS
18. Verify that there are no leaks around the heater. If there are,
Heater Replacement Kit: 6401-003-12-23*
attempt to tighten it down (with power secured to the unit at the
service breaker to prevent injury) as the tank will change shape
slightly as it heats up.
*The kit contains a heater, gasket, mounting hardware for
the heater and instructions.
19. Use the amp meter to take readings off of the power lines to the
CONTACT INFORMATION
heater, verifying the amperage draw to the machine data plate.
Jackson MSC Inc. provides technical support for all of the
dishmachines detailed in this manual. We strongly recommend that
20. Wait until the heater contactor kicks out (meaning that the tub
has reached the appropriate temperature) and allow the machine
you refer to this manual before making a call to our technical sup-
to operate approximately ten minutes to verify that there are no
port staff. Please have this manual with you when you call so that
leaks and that the heater is maintaining the tank temperature.
our staff can refer you, if necessary, to the proper page. Technical
support is available from 8:00 a.m. to 5:00 p.m. (EST), Monday
through Friday. Technical support is not available on holidays.
21. Replace the heater cover.
Contact technical support toll free at 1-888-800-5672. Please
remember that technical support is available for service personnel
only.
23. Replace the front door.
Heater Replacement Instructions
4
Revision A (09/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
|