DUAL TEMPERATURE, GAS HEATED
DOOR-TYPE DISHMACHINES
TECHNICAL MANUAL
INSTALLATION MANUAL FOR EXPORT UNITS
SERVICE MANUAL FOR DOMESTIC UNITS
FOR JACKSON MODEL:
TEMPSTAR GP
An
Company
Jackson MSC, Inc.
P.O. BOX 1060
HWY. 25E
BARBOURVILLE, KY. 40906
FAX (606) 523-9196
PHONE (606) 523-9795
June 24, 2004
P/N 7610-0011-90-68 (Revision B)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS OF THE TEMPSTAR GP
PERFORMANCE/CAPABILITIES
ELECTRICAL REQUIREMENTS
OPERATING CAPACITY (RACKS/HOUR)
RACKS PER HOUR
WASH PUMP MOTOR HP
3/4
57
CIRCULATOR PUMP MOTOR HP
1/12
DISHES PER HOUR
1425
1425
GLASSES PER HOUR
VOLTS
PHASE
AMPS
6.7
208 - 240
110 - 120
1
1
OPERATING CYCLE (SECONDS)
WASH TIME
13.4
45
11
2
RINSE TIME
WATER REQUIREMENTS
DWELL TIME
INLET TEMPERATURE
110 -140°F
52.0
TOTAL CYCLE TIME
60
GALLONS PER HOUR
WATER LINE SIZE I.P.S. (Minimum)
DRAIN LINE SIZE I.P.S. (Minimum)
FLOW PRESSURE P.S.I. (Optimum)
3/4”
TANK CAPACITY (GALLONS)
WASH TANK (MINIMUM)
BOOSTER TANK
1-1/2”
20
8.0
3.0
GAS REQUIREMENTS
BTU INPUT RATE
INLET LINE PRESSURE (natural gas)
(propane)
WASH PUMP CAPACITY
55,000
GALLONS PER MINUTE
150
7-10.5” wci
11-14” wci
TEMPERATURES
FRAME DIMENSIONS
WIDTH
WASH ---°F (MINIMUM)
RINSE ---°F (MINIMUM)
150
180
25 3/4”
25 1/4”
56 3/4”
34”
DEPTH
HEIGHT
STANDARD TABLE HEIGHT
MAXIMUM INSIDE CLEARANCE
17 1/4”
RACKS
DISH 20” X 20”
OPTIONAL
OPTIONAL
GLASS & SILVER 20” X 20”
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Do not confuse static pressure with flow pressure. Static pressure
VISUAL INSPECTION: Before installing the unit, check the con-
tainer and machine for damage. A damaged container is an indi-
cator that there may be some damage to the machine. If there is
damage to both the container and machine, do not throw away the
container. The dishmachine has been inspected and packed at
the factory and is expected to arrive to you in new, undamaged
condition. However, rough handling by carriers or others may
result in there being damage to the unit while in transit. If such a
situation occurs, do not return the unit to Jackson; instead, contact
the carrier and ask them to send a representative to the site to
inspect the damage to the unit and to complete an inspection
report.. You must contact the carrier within 48 hours of receiving
the machine. Also, contact the dealer through which you pur-
chased the unit.
is the line pressure in a “no flow” condition (all valves and services
are closed). Flow pressure is the pressure in the fill line when the
fill valve is opened during the cycle.
It is also recommended that a shock absorber (not supplied with
the Tempstar-GP model) be installed in the incoming water line.
This prevents line hammer (hydraulic shock), induced by the sole-
noid valve as it operates, from causing damage to the equipment.
PLUMBING CHECK: Slowly turn on the water supply to the
machine after the incoming fill line and the drain line have been
installed. Check for any leaks and repair as required. All leaks
must be repaired prior to placing the machine in operation.
ELECTRICAL POWER CONNECTION: Electrical and grounding
connections must comply with the applicable portions of the
National Electrical Code ANSI/NFPA 70 (latest edition) and/or
other electrical codes.
UNPACKING THE DISHMACHINE: Once the machine has been
removed from the container, ensure that there are no missing
parts from the machine. This may not be obvious at first. If it is dis-
covered that an item is missing, contact Jackson immediately to
have the missing item shipped to you.
Disconnect electrical power supply and place a tag at the discon-
nect switch to indicate that you are working on the circuit.
LEVEL THE DISHMACHINE: The dishmachine is designed to
operate while being level. This is important to prevent any dam-
age to the machine during operation and to ensure the best
results when washing ware. The unit comes with adjustable bullet
feet, which can be turned using a pair of channel locks or by hand
if the unit can be raised safely. Ensure that the unit is level from
side to side and from front to back before making any connec-
tions.
The dishmachine data plate is located on the right side and to the
front of the machine. Refer to the data plate for machine operat-
ing requirements, machine voltage, total amperage load and seri-
al number.
To install the incoming power lines, open the control box. This will
require taking a phillips head screwdriver and removing the one(1)
screw on the front cover of the control box. Install 3/4” conduit into
the pre-punched holes in the back of the control box. Route power
wires and connect to power block and grounding lug. Install the
service wires (L1 &L2) to the appropriate terminals as they are
marked on the terminal block. Install the grounding wire into the
lug provided. Tighten the connections and perform the “pull test”.
The tightened wires should remain in place after giving the wires
a moderate pull to see if they will come loose.
PLUMBING THE DISHMACHINE: All plumbing connections must
comply with all applicable local, state, and national plumbing
codes. The plumber is responsible for ensuring that the incoming
water line is thoroughly flushed prior to connecting it to any com-
ponent of the dishmachine. It is necessary to remove all foreign
debris from the water line that may potentially get trapped in the
valves or cause an obstruction. Any valves that are fouled as a
result of foreign matter left in the water line, and any expenses
resulting from this fouling, are not the responsibility of the manu-
facturer.
It is recommended that “DE-OX” or another similar anti-oxidation
agent be used on all power connections.
CONNECTING THE DRAIN LINE: The drain for the Tempstar-
GP is a gravity discharge drain. All piping from the 1 1/2” FNPT
connection on the waste accumulator must be pitched (1/4” per
foot) to the floor or sink drain. All piping from the machine to the
drain must be a minimum 1 1/2” I.P.S. and shall not be reduced.
There must also be an air gap between the machine drain line and
the floor sink or drain. If a grease trap is required by code, it
should have a flow capacity of 5 gallons per minute.
VOLTAGE CHECK: Ensure that the power switch is in the OFF
position and apply power to the dishmachine. Check the incoming
power at the terminal block and ensure it corresponds to the volt-
age listed on the data plate. If not, contact a qualified service
agency to examine the problem. Do not run the dishmachine if the
voltage is too high or too low. Shut off the service breaker and
mark it as being for the dishmachine. Advise all proper personnel
of any problems and of the location of the service breaker.
Replace the control box cover and tighten down the screws.
WATER SUPPLY CONNECTION: Ensure that you have read the
section entitled “PLUMBING THE DISHMACHINE” above before
proceeding. Install the water supply line (3/4” pipe size minimum)
to the dishmachine line strainer using copper pipe. It is recom-
mended that a water shut-off valve be installed in the water line
between the main supply and the machine to allow access for ser-
vice. The water supply line is to be capable of 20 PSI “flow” pres-
sure at the recommended temperature indicated on the data plate.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS CONNECTION
It is very important that the type and inlet pressure of the gas used corresponds to the machine data plate. This machine is equipped
with a 1/2” female line for connection of gas. The gas line used should be of the type approved for use with natural gas or propane,
depending on the gas selected to be used in this machine. The gas line should be sized to carry the maximum flow of 55,000 BTUs.
Too small of a gas line will result in poor performance. A manual gas shut-off valve must be installed in the gas line, located within an
accessible area of the machine. The gas line should be kept as short as possible and installed in a way to protect it from damage.
When making pipe connections, use an AGA approved pipe dope, being careful not to use excessive amounts as to foul the gas valve
or clog the gas line. When tightening the gas line always support the gas valve to avoid damage to the gas train.
Note: In propane installations, the gas must be supplied from a regulated source.
When making the connection to the booster unit, take care to start the gas line fitting by hand and tighten by hand to avoid cross thread-
ing. Tighten fitting with a wrench, taking care not to damage any internal components of the unit.
After making a final connection of gas, with power to the unit turned off, check all gas line fittings for leaks, using a liquid test solution,
and an approved leak detector.
WARNING
ENSURE THAT THERE IS NO ELECTRICAL POWER APPLIED TO THE MACHINE WHEN MAKING GAS CONNECTION.
CHECK ALL GAS CONNECTIONS FOR LEAKS PRIOR TO APPLYING POWER.
THE GASES USED FOR COMBUSTION IN THIS DISH MACHINE ARE HIGHLY FLAMMABLE.
DO NOT SMOKE AROUND THIS MACHINE.
ENSURE THAT THE AREA WHERE THIS MACHINE IS TO BE INSTALLED IS WELL-VENTILATED TO PREVENT THE
BUILD-UP OF COMBUSTIBLE GASES.
ENSURE THAT ALL LOCAL HEALTH, FIRE, AND BUILDING CODES ARE BEING ADHERED TO WHEN INSTALLING THIS
MACHINE. VERIFY WITH LOCAL OFFICIALS IF THERE ARE ANY QUESTIONS.
INSTALL A SHUT-OFF VALVE AT THE GAS SOURCE AND SUPPLY THE MACHINE USING A 1/2” LINE. CONNECT TO THE
1/2” NPT FITTING ON THE MACHINE.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
PREPARATION: Before proceeding with the start-up of the unit, WARM-UP CYCLES: For a typical daily start-up, it is recom-
verify the following:
mended to run the machine through 3 cycles to ensure that all of
the cold water is out of the system and to verify that the unit is
1. The pump intake, and wash tank strainers are in place operating correctly. To cycle the machine, ensure that the power
and is clean.
is on and that the tub has filled to the correct level. Lift the doors
and the cycle light will illuminate. When the light goes out, close
the doors, the unit will start, run through the cycle, and shut off
automatically. Repeat this two more times. The unit should now be
ready to proceed with the washing of ware.
2. The drain stopper is installed.
3. That the wash and rinse arms are screwed securely
into place and that their endcaps are tight. The wash
and rinse arms should rotate freely.
WASHING A RACK OF WARE: To wash a rack, open the doors
completely (being careful for hot water that may drip from the
POWER UP: To energize the unit, turn on the power at the service doors) and slide the rack into the unit. Close the doors and the
breaker. The voltage should have been previously verified as unit will start automatically. Once the cycle is completed, open the
being correct. If not, the voltage will have to be verified.
door (again watching for the dripping hot water) and remove the
rack of clean ware. Replace with a rack of soiled ware and close
FILLING THE WASH TUB:Ensure that the delime switch is in the the doors. The process will then repeat itself.
NORMAL position, and place the power switch into the ON posi-
tion. The Tempstar-GP should fill automatically and shut off when OPERATIONAL INSPECTION: Based upon usage, the wash tank
the appropriate level is reached (just below the wash tank strain- strainer may become clogged with soil and debris as the workday
er). Verify that the drain stopper is preventing the wash tub water progresses. Operators should regularly inspect the wash tank
from pouring out excessively. There will probably be some slight strainer to ensure it has not become clogged. If the strainer does,
leakage from the drain hole. Verify that there are no other leaks on it will reduce the washing capability of the machine. Instruct oper-
the unit before proceeding any further. The wash tub must be ators to clean out the wash tank strainer at regular intervals or as
completely filled before operating the wash pump to prevent dam- required by work load.
age to the component. Once the wash tub is filled, the unit is ready
for operation.
SHUTDOWN AND CLEANING: At the end of the workday, close
the doors. When the unit completes the cycle, turn the power
The water level was set at the factory. If the water level is not at switch to the OFF position and open the doors. Manually remove
the level noted above, it will require adjustment. Check to ensure the drain stopper from the tub and allow the tub to drain (NOTE:
that the recommended water pressure is being supplied to the the wash tank water will be hot so caution is advised). Once the
machine (20 PSI). If the water pressure is correct then the fill wash tub is drained, remove the wash tank strainer and the pump
valve will need adjustment. Use the following steps to adjust the suction strainer. Remove soil and debris from the strainer and set
cam. Turn power off at the machine circuit breaker. Open the to the side. Unscrew the wash and rinse arms from their mani-
control box cover. Locate the timer fill valve cam (Cam 4 from the folds. Remove the endcaps and flush the arms with water. Use a
timer motor). Locate the spanner wrench taped to the electrical brush to clean out the inside of the arms. If the nozzles appear to
panel. The spanner wrench is used to adjust the cam.
be clogged, use a toothpick to remove the obstruction. Wipe the
inside of the unit out, removing all soil and scraps. Reassemble
WARE PREPARATION: Proper preparation of ware will help the wash and rinse arms and replace them in the unit. The arms
ensure good results and less re-washes. If not done properly, only need to be hand tight, do not use tools to tighten them down.
ware may not come out clean and the efficiency of the dishma- Reinstall the strainers and close the doors.
chine will be reduced. It is important to remember that a dishma-
chine is not a garbage disposal and that simply throwing
unscraped dishes into the machine simply defeats the purpose
altogether of washing the ware. Scraps should be removed from
ware prior to being loaded into a rack.
Pre-rinsing and pre-soaking are recomended, especially for sil-
verware and casserole dishes. Place cups and glasses upside
down in racks so that they do not hold water during the cycle. The
dishmachine is meant not only to clean, but to sanitize as well, to
destroy all of the bacteria that could be harmful to human beings.
In order to do this, ware must be properly prepared prior to being
placed in the machine.
DAILY MACHINE PREPARATION: Refer to the section entitled
“PREPARATION” at the top of this page and follow the instructions
there. Afterwards, check that all of the chemical levels are correct
and/or that there is plenty of detergent available for the expected
workload.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW OF OPERATION
PRESSURE
GAUGE
VACUUM BREAKER
REGULATOR
RINSE ARM
FILL / RINSE SOLENOID
RINSE TEMP
T
>180 F
CHECK VALVE
WASH TANK
CHECK VALVE
WATER LEVEL
PROBE
BOOSTER
TANK
WL
TS
T
THERMOSTAT
WASH TANK
COILS
WASH TEMP
150-165 F
ECO
T-MID
HEAT
EXCHANGER
BURNER
ASSEMBLY
RECIRCULATING
PUMP
MODULATING
VALVE
COMBINATION GAS
CUTOFF VALVE
The Tempstar GP heating system is designed to heat and maintain the wash tank water temperature at a minimum of 150 F
as well as providing a constant 180 F rinse water temperature. Incoming water is supplied at a pressure of 20psi and between 110-
140 F. Incoming gas pressure should be between 7.0-10.5 WCI for natural gas, or 11.0-14.0 WCI for units supplied with propane. The
sequence of operation is as follows (please refer to the above diagram):
When the power is turned on at the ON/OFF switch the water level control board will sense a low water level in the wash tank
and the unit will begin to fill. This occurs as the rinse solenoid valve opens, allowing connected water to fill the booster tank, heat
exchanger and the rest of recirculating system, once the booster tank is full, water will fill the wash tank until the water level control sys-
tem is satisfied. Simultaneously with the fill, the rinse recirculating pump and the gas burner assembly are energized, this will begin
heat up of the unit. A transformer in the main control box supplies +12vdc to the electronics control drawer located in the lower section
of the unit. The electronics control board (ECB) is the brain of the system. The ECB receives various inputs and determines the amount
of heating required.
When energized the ECB receives input from the T-mid thermistor indicating a low water temperature in the recirculating sys-
tem. The ECB will power the ignition relay on the board, which in turn provides +12vdc to the direct spark ignition board (DSI). The DSI
sends +12vdc to the combination gas cutoff valve to open it. This will supply gas to the burner assembly. The DSI begins sparking the
igniter probe, and monitors the flames presence. If the flame is not sensed during the ignition attempt, then the DSI will lockout until
the software resets the DSI approximately 60 seconds later.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW OF OPERATION (CONTINUED)
The operator may turn the power off at the ON/OFF switch for approximately 5 seconds, and then back on. This will also reset the ECB
and the DSI. If flame is lost during normal burn, the DSI will attempt a reignition.
The ECB monitors the 12vdc signal from the DSI to the combination gas cutoff valve. The software in the ECB also reads the
temperature at the middle of the heat exchanger with the T-mid thermistor. After the 5.5 second ignition time, the software will increase
gas flow to the burner to minimum burn by increasing voltage to the modulating valve (MV). If the heat exchanger temperature is far
away from the stabilization temperature, the software will increase gas flow to maximum burn.
Once the heat exchanger temperature nears the stabilization temperature the gas flow is slowly reduced until the minimum
burn is attained. The software will keep the unit in minimum burn until the heat exchanger temperature exceeds stabilization tempera-
ture and then the gas will be shut off. Over many minutes, the software will turn the burner off and on repeatedly until all the water in
the system reaches the stabilization temperature. At this point the software will only turn the burner on every 1-2 minutes to maintain
the stabilization temperature. Now the unit is ready for operation.
As the dishwasher rinses with hot water from the booster tank, it is replaced with cooler water. The need to heat the new water
is sensed by the software and the burner is turned on. The software will modulate the gas flow between minimum and maximum gas
flow attempting to recover the stabilization temperature and always keeping the tank temperature above the required temperature.
The stabilization temperature may be adjusted by means of a potentiometer located on the ECB. This is referred to as the T-
set. (normally 4.25vdc)
The recirculating pump draws water from the rinse booster tank and circulates it through the wash tank coils where it will heat
the water residing in the wash tank. The water then returns to the heat exchanger where it is reheated. This hot water then flows back
to the rinse booster tank and repeats the cycle.
The thermostat,(in conjunction with the wash temp relay) is used during idle times to prevent wash tank temperature from
exceeding 170° F, during normal operation the wash tank will self regulate between 150-165°. However, when idle, the temperature in
the wash tank will slowly rise towards booster tank temperature until the temperature reaches 170° F. The wash tank thermostat will
cycle the heat exchanger & recirculating pump off. When the wash tank temperature lowers, the heat exchanger and recirculating pump
will energize. This will continue during all idle time. At any time that the unit is placed into operation, the wash
temp relay will energize and immediately power the heat exchanger and the recirculating pump, regardless of the thermostats position.
Excessive high temperatures in the system are avoided by the following: 1. High temperature limit control by input from T-mid
thermistor, 2. energy cutoff temperature lockout (ECO) by means of a bi-metallic switch independent of the microprocessor which will
break voltage to the combination gas cutoff valve if temperature in the system exceeds 210 F.
Excessive high pressures that potentially could be created in the system are vented directly to atmosphere by means of the
rinse booster tank and rinse arms.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
THERMOSTAT ADJUSTMENT PROCEDURE
1) Start up unit
2) Allow to fill, and start warm-up
3) Turn thermostat trim screw Counter Clockwise (CCW) 2 full revolutions
4) Allow wash temperature to reach 170LF on Wash Temperature Gauge
5) Turn thermostat trim screw Clockwise (CW) until flashing Green LED on control board turns off. (The recirculating pump
will also turn off).
6) To ensure that the trim screw has not been turned too far CW, turn CCW very slowly until Green LED turns on and once
again turn CW very slowly until Green LED goes out.
7) Start normal operation and monitor wash tank temperature.
8) If readjustment is needed repeat steps 5 - 7 until wash tank temperature maintains at 170LF during idle time.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO-CALIBRATION PROCEDURE
Model: TEMPSTAR GP, & TEMPSTAR TGP
This procedure must be completed every time you replace either a control board or a modulating valve.
AUTO - CALIBRATION
1. Turn the unit OFF at the main power switch and let stand for one minute.
2. Remove the lower front panel and set aside.
3. Remove the cover of the rectangular control box.
4. Locate the control board (see figure 1).
5. Locate and remove the jumper labeled ACAL (see figure 1) from the control board. Be careful to remove
metal jumper not just the plastic insulator. Make a note of the exact position the jumper was located.
Set jumper aside for later reinstallation.
6. With your multi-meter set on DC volts, attach to the molex plug going to the modulating valve.
NOTE: Do not disconnect molex plug. Insert probes in the rear of one side so the contact is made with
the metal pins inside of the plug. (see figure 2).
7. Turn dishmachine ON. Burner will ignite and run through a series of steps. Watch the readings of your
multi-meter. They will run approximately 11.9 VDC (23 VDC for the TGP) at the highest flame, step down
to about 6.0 VDC (12 VDC for the TGP) and then step down again slightly to 5.7 to 5.8 VDC (11.4 to 11.6 -
VDC for the TGP) before shutting the burner off. This whole process takes about 1 - 2 Minutes.
8. Once the burner goes out, turn dishmachine OFF.
9. Wait one minute.
10. Replace jumper on control board in the exact same place it came off.
11. Turn the dishmachine back ON.
12. Check for normal operation.
Figure 1
Figure 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONICS CONTROL BOARD (ECB)
Testing and Setting the Set Point Temperature
The Control Board regulates the temperature of the water in the heat exchanger system. This water is also used as the rinse water
for the rinse cycle of the dishwasher. It does this by regulating the flame of the burner by increasing or decreasing the voltage to
the modulating valve. The modulating valve, in turn, increases or decreases the gas pressure going to the burner manifold depend-
ing on the voltage it is getting from the control board. From time to time it may be necessary to check or adjust the setting of this
water temperature. To test the setting or to reset the temperature of the rinse water, make sure the unit is on and the green LED on
the board is flashing steadily. Insert the NEGATIVE (Black/Common) probe of a multi-meter set on DC volts in the BLACK test point
(see above). Insert the POSITIVE (Red) probe of the multi-meter in the BLUE test point. The reading will indicate the set point tem-
perature. The factory setting is 4.25 VDC which corresponds to 198LF (92LC). Adjustments to the set point are made on the BLUE
POTENTIOMETER directly below the BLUE test point. With a very small slotted screwdriver rotate the trim screw on the potentiome-
ter clockwise (CW) to increase the voltage (and Temperature) and counterclockwise to decrease.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TESTING THE THERMISTORS
There are two thermistors that are used in controlling the temperature of the water in the heat exchanger system. The T- in that sam-
ples the temperature of the water going into the heat exchanger and the T-Mid that samples the temperature halfway through the
heat exchanger. The Control Board constantly monitors the temperature at the T-Mid Thermistor and adjusts the burner pressure by
way of the Modulating Valve according to how far away that temperature is away from the set point temperature.
Thermistors are devices that change their resistance value with changes in temperature. By running a constant voltage through the
thermistor, one can read the change of voltage caused by the change of resistance thus determining the temperature of the thermis-
tor. There are test points on the control board (see above) that can be read with a multi-meter on the Direct Current Volt (DCV) scale
for each thermistor.
To test the temperature at the T-in Thermistor
There is a BLACK test point along the top edge of the control board on the right side of center. This is where the NEGATIVE
(Common/Black) probe of a multi-meter is inserted. There is an ORANGE test point along the top edge of the control board on the
left side of center. This is where the POSITIVE (Red) probe of a multi-meter is inserted. A DC voltage reading is then taken. Find
the voltage on the chart below and find the corresponding temperature.
To test the temperature at the T-Mid Thermistor
Using the same BLACK test point with the NEGATIVE probe of the multi-meters in testing the T-in thermistor above, also find the
YELLOW test point on the left side of the board just under the large plug (see above). Insert the positive probe of the multi-meter
and read DC Volts. Since the two thermistors have the same values, the same chart is used.
Gas Pack Thermister Conversion
4
3.5
3
2.5
2
1.5
1
0.5
0
Temperature °F (°C)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL BOARD LED LIGHT INDICATIONS
The Electronic Control Board (ECB) has two LED light indicators that can be seen at its upper left hand corner.
The following conditions for each light may be seen during operation of the unit.
1) Green LED is off.
A) Dishmachine is turned off, therefore no power to ECB.
B) Wash thermostat has cycled off, therefore breaking power to 12 volt transformer in the main control box.
This will also disrupt power to the ECB.
C) ECB may have never recieved an AUTO CALIBRATION.
D) ECB may be damaged due to high voltage.
E) Control chip in ECB may be misaligned, not fully inserted, or damaged.
2) Green LED is a illuminated and steady.
A) ECB has been damaged in some form.
3) Green LED is illuminated and flashing.
A) This is the normal operating condition.(whether the LED flashes rapidly, or at a slower rate).
4) Red LED is off.
A) This is the normal operating condition.
5) Red LED is illuminated and steady, or flashing.
A) This is an indication of a malfunction of the T-MID Thermistor. Thermister may be unplugged, grounded, have frayed
wiring, or other damage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Action
Dishmachine will not run. No power to the Service breaker tripped.
unit.
Reset breaker. If breaker trips again,
immediately contact an electrician.
Incoming power lines not installed in control Install power lines.
box.
Incoming power lines connections not
tightened.
Tighten connections.
Dishmachine will not run. There is power to Door switch shorted out or is disconnected. Check to ensure door switch wires are
the unit.
connected correctly. If so, replace door
switch.
Misadjusted or faulty "cycle reset" cam
microswitch.
Replace microswitch.
Machine runs, but there is not water.
No water supply to machine.
Check to ensure that all water valves are
open and that water is being supplied to the
machine at 20 PSI.
Incoming water supply solenoid not
operating.
Check to ensure that valve is wired
correctly. If so, replace valve.
Dishmachine fills continuously, even when Incoming water supply solenoid not
Check to ensure that valve is wired
correctly. If so, replace valve.
the machine is off.
operating.
Dishmachine fills continuously, only when
the power is on.
Incoming water supply solenoid not
operating.
Check to ensure that valve is wired
correctly. If so, replace valve.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Faulty fill microswitch.
Action
Replace microswitch.
Dishmachine fills continuously, only when
the power is on.
Cam timer stalled in fill position.
Shorted out ON/FILL switch.
If cam timer is not rotating, check the
voltage to the motor. If voltage is correct,
replace timer.
Check the voltage across the switch. If the
voltage is incorrect, replace the switch.
Shorted/defective liquid level control board Check voltage going to each component
or probe.
and ensure they are wired correctly. If
satisfactory, replace the defective part.
Dishmachine runs with the door open.
Door switch shorted out/wired incorrectly.
Check the wiring of the door switch, if
correct, replace the door switch.
Faulty wash relay (wash relay welded
closed).
Turn machine off, if wash relay doesn't
release, replace contactor.
Faulty control relay.
Measure the continuity between terminals #
6 and #9. If there is no continuity, replace
the relay.
Low wash water pressure.
Water level is too low.
Check to ensure that the drain stopper is in
and has an O-ring. Check to ensure that the
LLC board and probe are functioning
properly.
Pump intake strainer is clogged.
Remove and clean strainer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Action
Low wash water pressure.
Wash arms (nozzles) are clogged.
Remove wash arms and clean.
Pump impeller worn or broken.
Loose compression or NPT fitting.
Compression fitting over-compressed.
NPT fitting cross-threaded.
Loose fitting.
Replace pump.
Water leak in the gas booster pack.
Check all fittings to ensure that they are
tight.
Replace compression fitting.
Replace the fitting.
Gas leak.
Using an approved leak detector, determine
which fitting is loose and either tighten or
replace.
CAUTION: WHEN CHECKING FOR GAS
LEAKS DO NOT USE FLAME.
Bad thread sealer on fitting.
Remove fitting and apply an AGA approved
thread sealer.
Defective part (has crack, hole, or break in Replace the part.
it)
Low rinse temperature/low wash
temperature.
Excessive water flow into machine.
Adjust pressure regulator so that 20 PSI is
maintained at gauge. Check for leakage
past solenoid valve.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Action
Low rinse temperature/low wash
temperature.
Low inlet water temperature.
Ensure incoming water is 110 F at incoming
point of machine, may need to increase the
set point of the supply water heater.
Low gas pressure.
Check gas supply pressure.
Ensure proper operation of combination gas
cutoff valve.
Ensure manual gas cutoff valve is open.
Check for kinks in flexible gas supply line.
Improper circulation through system.
T-set needs adjustment.
Check recirculating pump operation. Check
for obstructions.
Ensure set point is approximately 4.25 VDC.
Defective T-mid thermistor (Red LED light Check Ohms reading is between 950 and
may be flashing).
1150 Ohms when probe is at room
temperature. Check for frayed wiring.
Ensure connection to control board.
Defective control board (ECB).
Perform auto-calibration. Ensure power
supplied to board is +12 VDC. Ensure green
LED light is flashing.
High rinse temperature.
T-set needs adjustment.
Ensure set point is approximately 4.25 VDC.
ECO failure. (Overprotection feature is
faulty and does not open at 210 F).
Remove wire from ECO terminal. If burner
unit turns off, ECO may be defective.
Replace ECO.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Defective thermostat.
Action
High wash tank temperature.
If wash tank temperature is greater than 170
F, back thermostat CCW one full turn and
restart unit. When cycle completes, set
thermostat to 170 F by turning CW.
Leak in wash tank heating coil, allowing hot Empty wash tank and observe coils with
recirculating system water to enter tank. recirculating system on.
No Green LED flash and the recirculating
New control board placed into system and Perform auto-calibration.
pump is running or the Green LED stays on, not calibrated.
but does not flash.
Damaged control board.
Replace control board.
Power to control board interrupted.
Check +12 VDC to control board (Voltage
should be between 10.8 and 14.4 VDC).
Make sure the transformer in main control
box is energized. CAUTION: REVERSE
POLARITY WILL DAMAGE THE CIRCUIT
BOARDS.
Circuit chip (microprocessor) pins not fully Check for bent pins. Ensure chip fully
inserted into its sockets. inserted by gently pressing with thumb.
Green LED flashes, but no ignition attempt T-mid thermistor reading incorrectly. (May Check T-mid voltage reading at test points
(no igniter, no gas).
be sensing non-existing high temperature.) on control board.
Ignition relay on control board inoperative. Place finger on ignition relay and turn power
on. Should hear or feel the relay actuating.
If not, check circuit chip (microprocessor)
fully inserted. If so, replace control board.
Voltage not being sent from control board to Check for 12 VDC at black wire going from
DSI.
control board to DSI. Ensure green wire on
DSI cable is grounded.
Green LED flashes, but no ignition. (Igniter ECO defective or not electrically connected. Check blue wire from DSI connected to one
sparks, no gas)
spade terminal of ECO and another blue
wire connected from other spade terminal of
ECO and to the combination gas cutoff
valve.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Action
Green LED flashes, but no ignition (igniter Gas flow interrupted.
sparks, no gas).
Check manual gas valve is open.
Check regulated gas pressure. (7.0 -10.5
WCI for natural gas or 11.0 - 14.0 WCI for
propane)
If gas line diameter is less than 1/2" or gas
line greater than 16 feet, reduce pressure
may result.
Combination gas cutoff valve is closed.
Ensure 12 VDC to both sides of valve. If
not, check ECO and DSI. If yes, valve may
have failed shut. Replace valve.
Modulating valve forced out of normal range Tap on gas supply line between the
and may be stuck (common occurrence
during shipment).
combination cutoff valve and the modulating
valve. This tapping helps to free the piston.
Green LED flashes, but no ignition (no
igniter sparks, gas flow and smell present).
Ignition wire loose or broken.
Improper gap on spark probe.
Defective DSI.
Check wire for continuity. Check connection
to both the DSI and spark probe.
Check height of probe above burner (should
be 1/8"). Check gap between probe ends
(1/8"). Ensure probe is not touching burner.
Disconnect ignition wire from DSI spade
connector. During ignition, a spark should
be seen at this spade. If none, replace DSI.
If spark exists, replace ignition wire.
The unit ignites, but will not rise above
ignition burn.
Improper operation of modulating valve.
Check voltage to modulating valve. If
greater than 2.0 VDC, modulating valve may
have been forced out of its operating range.
Tap on gas supply line between the
combination cutoff valve and the modulating
valve. This tapping helps to free the piston.
If less than 2.0 VDC, replace control board.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING SECTION
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service techni-
cian. Many of the tests require that the unit have power to it and live electrical components be exposed.
USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Symptom
Possible Cause
Action
The unit ignites, but will to rise above
ignition burn.
T-mid thermistor inoperative.
Check T-mid thermistor readings at control
board set points.
T-set too low.
Check T-set is at 4.25 VDC.
Obstruction in gas burners or gas nozzles. Remove burner manifold and check for
obstructions.
Control board damaged.
Replace control board.
Exhaust contains dark smoke.
Incorrect gas nozzles for type of gas being Remove burner manifold and check correct
used.
nozzle orifice size.
Gas leak may be present.
Check for localized large yellow flame, or a
flame located above the burner.
Obstruction in heat exchanger vent or air
intake.
Check for obstructions.
Ignition attempt with flame already burning. Flame proofing not occurring.
Check ignition wire. Check that lights above
connection point to DSI are dimly lit
(proofing signal is present).
Heat exchanger and recirculating pump de- Failure or incorrect setting of thermostat.
energize at end of rinse cycle with wash
tank temperature below 170 F.
Back thermostat CCW one full turn and
restart unit. When cycle completes, set
thermostat to 170 F by turning CW.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE DIMENSIONS
TABLE DIMENSIONS
CORNER INSTALLATION
20 1/2”
OPENING
2 1/4”
4”
25 1/4”
MIN.
3/4”
1 1/2” ROLL
20 1/2”
TABLE DIMENSIONS
CONNECTION TO DISHMACHINE
TABLE DIMENSIONS
STRAIGHT THROUGH
INSTALLATION
25 1/4”
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN ASSEMBLY
01
02
08
09
10
03
04-NOT
SHOWN
05
11
12
06
07-NOT
SHOWN
13 NOT
SHOWN
14
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08a
08b
09
10
11
12
13
14
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
Control Box Cover
Control Box Assembly
Front Door
Left Door Assembly
Hood Assembly
Front Panel
5700-041-90-72
Refer To Control Box Page
5700-002-21-15
5700-002-21-31
5700-002-18-75
5700-002-19-44
5700-031-89-63
5700-002-18-86
5700-002-21-09
5700-002-21-33
5700-002-21-34
5700-002-16-32
5700-002-19-45
5700-002-22-70
5340-108-02-06
Left Side Panel
Incoming Plumbing Assembly (115v)
Incoming Plumbing Assembly (208v)
Right Door Assembly
Cantilever Arm Assembly
Right Side Panel
Vent Flue Assembly
Vent Flue Adapter (NOT SHOWN)
Bullet Feet
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL BOX ASSEMBLY - FRONT VIEW
01
02
03
04
05 06
07
08
09 10
11
12
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08a
08b
09
10
11
12
1
1
1
1
1
1
1
1
1
1
1
8
1
Control Box Cover Decal
9905-021-91-15
6685-111-68-48
5945-504-07-18
5305-173-12-00
5930-301-21-18
5930-011-49-55
9905-011-34-96
5945-021-94-11
5945-002-01-73
5945-504-08-18
5700-021-34-54
5945-111-68-49
5700-111-68-49
Rinse Thermometer, 48" Lead
Power Light (Red)
Screw, 10-32 X 3/8" Phillips Truss Head
Delime ( Manual Wash) Switch
On / Off Power Switch
Delime/Normal Decal
Timer, 220v/60, 8 cam
Timer, 110v/60, 8 cam
Cycle Light (Green)
Timer Mounting Bracket
Micro Switch
Wash Thermometer, 96" Lead
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL BOX ASSEMBLY - TOP VIEW
01
14
13
02
03
04
12
11
05
06
07
10
08
09
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL BOX ASSEMBLY-TOP VIEW
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
Heyco Plug
5975-200-40-00
5975-011-47-74
5940-200-76-00
5940-500-09-61
5945-109-05-69
5945-109-03-69
5945-109-05-69
5945-109-03-69
5945-021-94-11
5945-002-01-73
5920-401-03-14
5945-111-35-19
5945-111-47-51
6680-200-08-21
6680-200-07-21
5700-002-18-97
5700-001-96-32
5700-002-18-95
5950-002-17-87
5975-011-45-14
Fitting, Conduit Non-Metalic, 3/4" x 45
Ground Lug
Terminal Block 2 pole
03
04
05a
05b
06a
06b
07a
07b
08
09a
09b
10a
10b
11a
11b
12
Contactor, 2 pole, 110v (wash motor)
Contactor, 2 Pole, 220v, 20amp (Wash Motor)
Contactor, 2 pole, 110v (wash motor)
Contactor, 2 Pole, 220v, 20amp (Wash Temperature)
Timer, 220v/ 60, 8 Cam
Timer, 110v/ 60, 8 Cam
Fuse Holder
Relay Control 110v
Relay, Control 240v/ 50-60hz Top Mount
Liquid Level Control, (220v)
Liquid Level Control, (110v)
Inner Control Panel Assembly, GP 110/60/1
Inner Control Panel Assembly, GP 208/60/1
Transformer Mounting Bracket
Transformer, 100-240vac to 12vdc
Fitting, Conduit Non-Metalic, 1/2" x 90
13
14
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOOD ASSEMBLY
01
02
03
04
05
06
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
03
03
04
05
06
1
1
28
28
28
1
Double Door Guide, Left Front
Double Door Guide, Right Front
Screw, 1/4"- 20 x 1/2"
5700-021-33-20
5700-021-33-19
5305-274-02-00
5311-174-01-00
5310-374-01-00
5700-021-84-71
5700-002-18-76
5700-021-84-70
Washer, s/s 1/4" ID
Locknut, 1/4"- 20 s/s Hex w/Nylon Insert
Door Guide, Left Rear
1
1
Hood Weldment
Door Guide, Right Rear
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CANTILEVER ARM ASSEMBLY
01
12
11
02
03
10
09
04
05
06
07
08
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
07
08
09
10
11
12
1
1
1
2
2
1
4
4
6
2
2
2
1
Magnet, Reed Switch
Door Guide, Right Rear
Door, Right Side Assembly
Plug, Cantilever
5930-111-51-68
5700-021-84-70
5700-002-21-33
5340-011-35-00
5700-011-90-99
5700-031-50-67
5311-174-01-00
5310-374-01-00
5700-001-98-69
5700-001-28-18
5700-031-88-00
5700-000-75-78
5700-041-90-56
Cantilever Arm Connector
Cantilever Arm
Washer, s/s 1/4" ID
Locknut, 1/4"- 20 s/s Hex w/Nylon Insert
Wear Button, 1/2" Dia, UHMW
Spring Rod
Cantilever Arm Support Bracket
Yoke Assembly
Hood Assembly
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TUB ASSEMBLY
01
02
03
04
05 06
07
08
09
10
11
12
13
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
02
03a
03b
04
05
06
07
08
09
10
11
12
13
1
2
2
1
1
1
1
3
2
1
1
1
2
1
1
Bracket, Reciculating Pump
Lock Washer, 5/16" s/s Split Ring
Bolt, Hex Head 5/16"- 18 X 5/8"
Pump, Recirculating 110v Assembly
Pump, Recirculating 220v Assembly
Bracket, Thermostat
5700-002-14-85
5311-275-01-00
5305-275-09-00
5700-002-17-84
5700-002-17-77
5700-011-73-77
5930-121-67-72
4730-011-39-01
4730-206-08-00
6685-111-68-49
6680-200-02-68
5700-002-18-85
4730-719-01-37
5700-002-18-77
6105-121-99-78
Thermostat, Wash Temperature Over Limit 78 Deg
Clamp, 5/8" Nylon
Elbow, 90 Deg 1/2" Street Brass
Thermometer, Wash 96" Lead
Probe, High Water
Hose Assembly, Wash Pump Discharge 1 1/4" ID
Clamp, Reg. Range 1 5/16"- 2 1/4"
Tub Weldment
Wash Pump & Motor Assembly, 115-230/60/1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK OF TUB, & DRAIN ASSEMBLY
14
13
01
02
12
11
10
03
04
05
06
09
07
08
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
1
1
1
1
1
1
1
2
2
2
1
2
2
1
Tub Weldment
5700-002-18-77
5700-002-19-45
6105-121-99-78
5700-002-18-78
5700-002-21-29
5700-002-20-58
5700-002-17-79
4730-206-08-00
5306-956-05-00
4730-609-05-00
5700-002-17-71
5340-109-02-00
5700-001-28-18
5700-002-17-73
Vent Flue Assembly
Wash Pump & Motor Assembly 115-230/60/1
Frame Weldment
Plumbing, Drain Assembly
Bracket, Drain Support
Hose, 3/4" Recirculating Pump Suction
Elbow, 90 Deg 1/2" Street Brass
Bolt, Cantilever Hanger Eye 3/8"-16
Plug, Bulk Head
Hose, 1/2" Recirculating Pump Discharge
Spring
Rod, Spring
Hose, 1/2" Heat Exchanger Inlet Assembly (not shown)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWER ASSEMBLY (RIGHT SIDE)
01
02
03
04
05
08
09
11
12
06
07
10
13
14
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
1
1
1
1
1
6
1
1
1
1
2
1
1
1
Rinse Tank Assembly
Saddle, Burner
5700-002-17-80
5700-002-18-74
5700-002-19-45
5700-002-20-50
5700-002-18-27
5310-373-01-00
5700-002-18-81
6105-121-99-78
4730-011-34-90
5700-002-20-58
5700-001-17-87
5700-011-93-95
5700-002-21-29
5700-002-17-75
Vent Flue Assembly
Heat Exchanger, Copper
Air Shield
Locknut, 10-24 s/s Hex w/Nylon Insert
Bracket, Pump Support Assembly
Wash Pump & Motor Assembly 115-230/60/1
Clamp, 5 5/8" to 6"
Bracket, Drain Support
Washer,
Hose, Flex Gas s/s Assembly
Plumbing, Drain Assembly
Hose, Heat Exchanger Outlet Assembly
29
Download from Www.Somanuals.com. All Manuals Search And Download.
INCOMING PLUMBING ASSEMBLY
22
23
21
26
25
24
01
02
03
04
20
19
05
06
07
18
17
08
09
16
15
14
13
12
10
11
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INCOMING PLUMBING PARTS LISTS
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
18
19
20
21
22
23
24
25a
25b
26
1
1
1
1
1
1
1
1
1
2
1
1
5
1
1
1
1
1
1
2
4
2
1
3
1
1
1
3
Pressure Guage, 0-100 PSI
6685-111-88-34
4810-011-72-67
4730-211-04-00
6685-011-58-22
5700-021-34-02
5930-111-51-68
5930-111-41-70
5700-011-46-97
5700-002-18-87
5330-200-11-00
5700-002-17-99
5700-002-17-98
5310-373-01-00
4730-011-51-16
5700-002-19-08
5700-002-18-90
5700-002-23-89
5311-174-01-00
5310-374-01-00
5330-111-42-81
4730-212-05-00
4730-206-04-34
5700-021-47-65
4730-209-07-37
4820-300-08-00
4810-100-53-00
4810-100-03-18
4730-207-34-00
Ball Valve, Test Cock, 1/4" Bronze
Tee, Brass, 3/4 X 3/4 X 1/4
Pressure Regulator
Incoming Plumbing Support Bracket
Magnet, Reed Switch
Reed Switch
Conduit, 1/2" X 14"
Plumbing Assembly, Inlet to Rinse Tank
Washer, Teflon
Panel, Lower Back Cover
Panel, Upper Back Cover
Locknut, 10-24 s/s Hex w/Nylon Insert
Clamp, Nylon 1 1/4"
Conduit, 3/4" X 37 1/2"
Plumbing Assembly, Outlet From Rinse Tank
Clamp, Double Pipe
Washer, 1/4" ID s/s
Locknut, 1/4-20 s/s Hex w/Nylon Insert
Gasket, Vellumoid
Union, Brass, 3/4"
Elbow, 3/4" 90 Deg Street Brass
Rinse Injector SDS Weldment
Plug, 1/8" NPT Brass
Vacuum Breaker, 3/4"
Solenoid Valve, 3/4" 110v
Solenoid Valve, 3/4" 240v
Close Nipple, 3/4" Brass
31
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS PACK ASSEMBLY
01
02
03 04
05
06
07
08
09
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
1
1
1
1
1
1
1
1
1
1
1
1
Hose, Flex Gas s/s Assembly
5700-011-93-95
5700-002-18-62
5700-002-12-22
4810-002-29-44
4810-002-29-45
5700-002-12-23
5700-002-12-27
5700-002-12-28
6680-002-12-24
5700-002-18-69
5700-002-19-82
5700-002-20-50
Cover, Electronics Drawer w/Sight Glass
T-Mid Thermister Assembly
Valve, Solenoid , Combination Cut Off (natural gas)
Valve, Solenoid , Combination Cut Off (propane)
T-In Thermister Assembly
Valve, Modulating 12v (natural gas)
Valve, Modulating 12v (propane)
Spark Probe Igniter
03
04a
04b
05
06a
06b
07
08a
08b
09
Gas Pack (natural gas)
Gas Pack (propane)
Heat Exchanger (copper)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
UPPER WASH, & RINSE ARM ASSEMBLY
01
02
03
04
05
06
07
08
09
10
11 12
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08
09
10
11
12
2
1
1
1
2
2
1
1
8
2
1
2
Wash Arm End Plug
Rinse Manifold Assembly
Wash Manifold Tube
Wash Arm
5700-011-35-92
5700-021-47-61
5700-131-15-07
5700-021-35-93
5310-276-01-00
5305-276-10-00
5700-031-34-82
5700-031-50-63
5310-374-01-00
4730-609-04-00
5700-041-90-56
5700-021-33-39
Nut, 3/8-16 Hex
Bolt, 3/8-16 X 1-1/4" Long Hex
Upper Wash Casting
Rinse Arm
Locknut, 1/4"- 20 s/s Hex w/Nylon Insert
Rinse Arm End Plug
Hood Assembly
Bracket, Door Connecting
33
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWER WASH, & RINSE ARM ASSEMBLY
01
02
03
04
05
06
07
08
09
10
11
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08
09
10
11
2
2
1
1
1
1
1
2
1
1
1
Wash Arm End Plug
Rinse Arm End Plug
Bulk Head Plug
5700-011-35-92
4730-609-04-00
4730-609-05-00
5700-031-50-07
5700-031-50-63
5700-021-47-61
5700-031-46-01
5305-276-10-00
5700-021-35-93
5700-002-01-01
5700-002-05-18
Strainer Weld Assembly
Rinse Arm
Rinse Manifold Assembly
Lower Wash Casting
Bolt, 3/8" X 11/4" Long
Wash Arm
Rack Guide Weldment
Lower Wash Manifold
34
Download from Www.Somanuals.com. All Manuals Search And Download.
STEAM COIL ASSEMBLY
07
08
09
10
01
02
11
12
13
03
04
14
15
05
06
16
17
18
35
Download from Www.Somanuals.com. All Manuals Search And Download.
STEAM COIL ASSEMBLY (PARTS LISTS)
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
1
4
4
1
1
1
1
1
1
4
1
2
1
1
1
1
1
1
1
Stand-D, Steam Coil Support
5700-002-08-53
5310-374-01-00
5311-174-01-00
5700-041-90-30
5700-001-27-55
5700-001-25-69
5700-002-08-52
4730-609-05-00
5700-021-41-38
5700-001-17-86
5700-002-08-50
5310-374-01-00
5700-001-22-23
5700-001-22-24
5700-002-08-51
5700-111-68-49
6680-200-02-68
5930-121-67-72
5330-400-05-00
Locknut, 1/4-20 s/s Hex w/Nylon Insert
Washer, s/s 1/4 I.D.
Tub Weldment
Overflow Support Bracket
Wash, Overflow Weldment
Stand-C, Steam Coil Support
Bulk Head Plug
Steam Coil Weldment
Gasket, Steam Coil
Stand-A, Steam Coil Support
Locknut, 1/4-20 s/s Hex w/Nylon Insert
Suction Strainer Weldment
Bracket, Suction Strainer
Stand-B, Steam Coil Support
Wash Thermometer 96" Lead
Probe, High Water
Thermostat, Wash Regulating 78 Deg
O- Ring, Vitan #03-218
36
Download from Www.Somanuals.com. All Manuals Search And Download.
RINSE TANK ASSEMBLY
NOTE:THESE UNIONS
ARE NOT INCLUDED WITH
THIS ASSEMBLY.
07
01
08
02
03
09-NOT
SHOWN
04
05
06
ITEM
QTY
DESCRIPTION
MFG NO.
1
2
2
1
3
2
1
1
1
1
Rinse Tank Assembly
5700-002-17-80
4730-212-05-00
4730-207-46-00
4820-002-01-76
4730-207-34-00
4730-206-04-34
5700-002-17-81
4730-206-08-00
4820-011-94-20
5700-021-92-39
01
02
03
04
05
06
07
08
09
Union, Brass (Comes With Incoming Plumbing Assy)
Nipple, 3/4" X 2"
Valve, 3/4" NPT Female Check High
Nipple, 3/4" NPT X 1 3/8" Close Brass
Elbow, 3/4" Street Brass
Rinse Tank Weldment
Elbow, 90 Deg 1/2" Street Brass
Valve, 3/4" NPT Female Check
Circulating Return Tube (NOT SHOWN)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONIC CONTROL DRAWER COMPONENTS
RED GREEN
LED LED
1
2
3
4
5
6
7
8
9
ITEM
QTY
DESCRIPTION
MFG NO.
01
02
03
04
05
06
07
08
09
1
1
1
1
1
1
1
1
1
Electronic Control Drawer Assembly
Wiring Harness-Thermistor Cable
Electronic Control Board (ECB)
Wiring Harness-DSI Cable
5700-002-21-10
5700-002-12-34
6680-002-12-26
5700-002-12-36
5700-002-12-35
5700-002-37-03
6680-002-12-25
5700-002-12-37
5925-022-36-94
Wiring Harness-Power Supply Cable
Wiring Harness-Modulating Valve (GP)
Direct Spark Ignition Board (DSI)
Ignition Cable
Circuit Breaker 3 amp
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Tempstar GP
ELECTRICAL DIAGRAM
110/120 VOLT - 60 HERTZ - 1 PHASE
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Tempstar GP
ELECTRICAL DIAGRAM
208/240 VOLT - 60 HERTZ - 1 PHASE
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|