VIDEO CASSETTE RECORDER
HR-A60U
INSTRUCTIONS
Printed in Thailand
LPT0784-001A
COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD.
K
J4F90401A
02/12
Dear Customer,
NOTE:
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
Changes or modifications not approved by JVC could void user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
CAUTIONS
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
Consult the dealer or an experienced radio/TV technician for help.
Failure to heed the following precautions may result in damage
to the VCR, Remote or video cassette.
1
DO NOT place the VCR . . .
...in an environment prone to extreme temperatures or humidity.
...in direct sunlight.
...in a dusty environment.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
...in an environment where strong magnetic fields are generated.
...on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings.
3. DO NOT place heavy objects on the VCR or on the Remote.
4. DO NOT place anything which might spill on the top of the VCR
or on the Remote.
5. AVOID violent shocks to the VCR during transport.
WARNING:
For Customer Use:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
Enter below the Model No. and Serial No. which are located
on the rear of cabinet. Retain this information for future
reference.
Model No.
CAUTION:
This video cassette recorder should be used with AC 120V~, 60Hz
only.
Serial No.
To prevent electric shocks and fire hazards, DO NOT use any other
power source.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION:
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video
cassette recorder. However, S-VHS recording is not possible with
this model.
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME
LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK)
that makes it possible to play back S-VHS recordings with
regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
• As an Energy Star® Partner, JVC has determined that this
product or product model meets the Energy Star® guidelines for
energy efficiency.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Download from Www.Somanuals.com. All Manuals Search And Download.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the
product to its normal operation.
Buttons, Connectors and Indicators
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
Front Panel
REC
3. Replacement Parts
POWER
When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or which
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
STOP/EJECT
Cassette loading slot
PLAY
4. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in safe operating condition.
How to use the Remote
Before use, insert two AAA size batteries into the Remote with the
FF
CH+/-
VIDEO/AUDIO (L/R)
input connectors
polarity ( and ) matched correctly as indicated on the battery
REW
compartment or on the lid.
Remote sensor
POWER indicator
TV/VCR indicator
TIMER indicator
• Point the Remote toward the remote sensor on the target
component.
REC indicator
• The maximum operating distance of the remote control is about 5
m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for a
few seconds, replace the batteries and then try again.
Rear Panel
Video heads cleaning
AC power cord
UHF/VHF IN (ANT)
Use a dry cleaning cassette — TCL-2— when:
• Rough, poor picture appears while a tape is played back.
• The picture is unclear or no picture appears.
UHF/VHF OUT (TV)
VIDEO/AUDIO (L/R) OUT
Download from Www.Somanuals.com. All Manuals Search And Download.
– Buttons, Connectors and Indicators –
Remote
Connections and VCR channel
Setting
POWER
POWER
Check contents
Make sure the package contains all of the accessories listed
in “Specifications”.
Situate VCR
Place the VCR on a stable, horizontal surface.
1
1
4
7
2
5
8
3
6
9
Number keys
CH–/+
2
AUX
REC
+
0(AUX)
–
CH
PAUSE
PLAY
Connect VCR to TV
3
REC
PAUSE
PLAY
REW
Antenna or cable
Coaxial cable
REW
FF
FF
STOP
ENTER
TIMER
MENU
ENTER
STOP
SET
MENU
Flat feeder
+
–
Matching transformer
(not supplied)
CANCEL
C.RESET
SP/EP
CANCEL
SET–/+
TV/VCR
TV/VCR
TIMER
SP/EP
–
C.RESET
DISPLAY
+
A.MONITOR
TV POWER
INPUT
A.MONITOR
TV CH
DISPLAY
TV POWER
INPUT
–
+
TV VOL
TV CH–/+
TV VOL–/+
This Remote transmit A code
signals only; it is not applicable
to B code signals.
Back of VCR
On-screen display
TV
To 75 Ω terminal
RF cable (supplied)
If you press DISPLAY on the Remote, you can see the current VCR
status on the TV screen. Press DISPLAY again to exit on-screen
display.
The indications are not recorded even if the VCR is in the recording
mode.
Audio/video cable (not supplied)
To audio/video input connectors
WHILE WATCHING TV
RF Connection
DAY AND CLOCK TIME
CHANNEL
1
2
Disconnect the TV antenna from the TV.
Connect the TV antenna cable to the UHF/VHF IN
terminal on the rear of the VCR.
Connect the supplied RF cable between the UHF/VHF
OUT terminal on the rear of the VCR and the TV’s
antenna input terminal.
STEREO AND
SEPARATE AUDIO
PROGRAM (SAP)
3
TAPE
OUTPUT
SPEED
SELECTION
REAL TIME COUNTER
AV Connection
(improves picture quality during tape playback.)
If your TV is equipped with audio/video input connectors
WHILE OPERATING A TAPE
OPERATING MODE
1
Connect the antenna, VCR and TV as shown in the
illustration.
Connect an audio/video cable between the AUDIO/
VIDEO OUT connectors on the rear of the VCR and the
audio/video input connectors on the TV.
HI-FI STEREO
2
AUTO REPEAT
TAPE IN
AUTO TRACKING
• Even if you are using audio/video cables to connect your
VCR to your TV, you must also connect it using the RF
cable. This will ensure that you can record one show while
watching another.
OUTPUT
SELECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
– Connections and VCR channel Setting –
– Initial Settings –
Auto Clock Setting
4
Set VCR channel
Connect the Antenna or Cable system.
• If you use a cable box, turn it on.
1
To view playback of a recorded tape, or to watch a program
selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel) when a TV is connected with
the 75 ohm coaxial cable only.
2
3
Plug the AC Power cord to the AC outlet.
Make sure the VCR is turned off.
1
Press and hold 3 or 4 on the Remote for 3 seconds in
standby mode. The TV/VCR indicator will start to flash.
• If you press POWER, the Auto Clock set is not effective.
4
5
6
Wait at least three minutes and press POWER.
2
Turn ON the TV and set to CH 3 or 4 to correspond with
the channel selected in 1.
Press DISPLAY to check the clock on the TV screen.
3 Press POWER to turn on the VCR.
If the clock is not set, check the Antenna condition. The
Auto Clock may not function properly if the reception
condition is not good.
The POWER indicator will light.
4
Press TV/VCR to select the VCR
position.
Auto Clock Adjustment
The TV/VCR indicator will light.
5 Select any channel to receive a
TV station in your area.
The Auto Clock Adjustment will be performed at 12:00 PM
everyday if you turn off the VCR.
• If you use a cable box and you want Auto Clock adjustment
to be performed, the cable box must be left on.
• The Auto Clock Adjustment is not effective when there is a
difference of more than 5 minutes exists between the built-
in clock time and the actual time.
The channel number will appear
on the screen for about 4 seconds.
Initial Settings
To Set Auto Clock To Off
Language Setting
The default setting is “ENGLISH”.
When shipped from factory “AUTO CLOCK” option is set to ON.
But if you do not want Auto Clock set (Adjustment):
Access Menu screen
1
Turn on the VCR.
1
2
3
Press MENU on the Remote. Press SET
–/+ to select “SYSTEM SETUP”, then
press ENTER.
Press MENU.
Press SET –/+ to select “SYSTEM SETUP” option, then
press ENTER.
Access Language screen
Press SET –/+ to select “LANGUAGE”,
then press ENTER.
2
Press SET –/+ to select “AUTO CLOCK” option.
4
5
6
Press ENTER to select OFF.
Press MENU repeatedly to return to the normal screen.
• When “AUTO CLOCK” is set to OFF, the Auto Clock
adjustment does not function. Set the clock manually.
Select language
3
This VCR offers you the language
choice to view menus and some
messages — in English, Spanish or
French. Press SET –/+ to select your
desired language, then press ENTER.
Press MENU twice to return to normal screen.
To Set Standard Time
In the rare event that you live within broadcast range of two
stations in two different time zones, the VCR may recognize
the wrong station for the Auto Clock set.
To correct the situation:
Clock Setting
Preparations
Press MENU.
1
2
You must set the date and time for timer recording.
Press SET –/+ to select “SYSTEM SETUP” option, then press
ENTER.
Auto Clock Setting
Press SET –/+ to select “STANDARD TIME” option, then
press ENTER.
3
The Auto Clock function will automatically set the built-in
clock (Month, Day, Year and Time) when the VCR is
connected to an Antenna or Cable system and it is turned
off. As the VCR searches for a receivable station in your area
and it receives a broadcast signal for Auto Clock, the Auto
Clock needs several minutes to set itself.
Download from Www.Somanuals.com. All Manuals Search And Download.
– Initial Settings –
Press SET –/+ to select your time zone, then press
ENTER.
4
Tuner Setting
This VCR is equipped with a channel memory feature which
allows channels to skip up or down to the next channel set
into memory, skipping over unwanted channels. Before
selecting channels, they must be programmed into the VCR’s
memory. In addition to normal VHF and UHF channels, this
VCR can receive up to 113 Cable TV channels. To use this
VCR with an antenna, set the TV/CATV menu option to the
TV mode. When shipped from the factory, this menu option
is in the CATV mode.
ATLANTIC
:
GMT – 4 hours
(GMT: Greenwich Mean Time)
GMT – 5 hours
GMT – 6 hours
GMT – 7 hours
GMT – 8 hours
GMT – 9 hours
GMT – 10 hours
AUTO SET
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
AUTO
:
:
:
:
:
:
:
5
Press MENU twice to return to the normal screen.
– TV/CATV Selection
NOTES: • To be able to select the standard time, the clock
must first be set by “AUTO CLOCK” once.
Access Menu screen, then CH
Setup screen
1
• If you live in Newfoundland and the Auto Clock
does not function properly, set the AUTO CLOCK
menu option to OFF and set the clock manually.
Press MENU on the Remote. Press
SET –/+ to select “CH SETUP”, then
press ENTER.
Manual Clock Setting
Perform TV/CATV Selection
CH SETUP
2
Access Menu screen
1
TV CATV
AUTO CH MEMORY
ADD/DELETE
Press SET –/+ to select “TV/CATV”,
Press MENU on the Remote. Press
SET –/+ to select “SYSTEM SETUP”,
then press ENTER.
then press ENTER to select the TV
or CATV mode. The arrow indicates
the selected mode.
Access Clock Set screen
Press SET –/+ to select “CLOCK SET”,
then press ENTER.
2
TV
- VHF/UHF channels
CATV - CABLE TV channels
Press MENU twice to return to normal screen.
Setting channels automatically
– Auto Channel Memory
Set month, day, year and time
3
Press SET –/+ until the desired month
appears, then press ENTER. Set the
day, year and time in the same way.
The VCR can receive a maximum of
181 channels by presetting the
channels into memory.
Access Menu screen, then CH
1
4 Start clock
Setup screen
Press MENU to return to normal
Press MENU on the Remote. Press
screen.
SET –/+ to select “CH SETUP”, then
CH SETUP
press ENTER.
TV CATV
AUTO CH MEMORY
ADD/DELETE
2
Perform Auto Channel Memory
Press SET –/+ to select “AUTO CH
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to change
blinks, then press SET –/+.
MEMORY”, then press ENTER.
3
Complete Auto Channel Memory
NOTE:
The auto tuning will start. The
channel display will count up and
when finished, the screen returns to
normal.
After a power failure or disconnection of the power, the
timer settings will be lost. In this case, reset the present time.
Download from Www.Somanuals.com. All Manuals Search And Download.
– Initial Settings –
Setting channels manually
Playback
– Manual Channel Set
Basic Playback
You can add the channels you want or delete the channels
you do not want manually.
Load a cassette
1
Access Menu screen, then
CH Setup screen
1
Press MENU on the Remote.
Press SET –/+ to select “CH
SETUP”, then press ENTER.
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
Access ADD/DELETE Mode
2
Make sure the window side is up, the rear
label side is facing you and the arrow on
the front of the cassette is pointing
towards the VCR.
Press SET –/+ to select “ADD/
DELETE”, then press ENTER.
• Do not apply too much pressure when
inserting.
• The VCR turns on, and the counter is
reset, automatically.
Add or Delete desired
channels
3
• If the cassette’s record safety tab has been removed, playback
begins automatically.
1
Press SET –/+ on the Remote to
select a channel number you
want to add or delete.
• If you press any operation buttons while the cassette is not
loaded, “
“ will flash on the screen for 4 seconds.
2
To add channels
Press ENTER until “ADD” appears on the screen to set to
add the unmemorized channel.
Start playback
2
Press PLAY ( ).
To delete channels
Press ENTER until “DELETE” appears on the screen to set
to delete the channel from memory.
During playback
Stop playback
Repeat to to add or delete other channel.
1
2
3
Press MENU three times to return to normal screen.
OR Press STOP/EJECT (I/
on the VCR.
Press STOP ( ) on the
Remote.
)
NOTE: You can’t select “CH SETUP” if you set the channel to “L”.
Pause playback and view still picture
Press PAUSE.
• Press PLAY ( ) to resume
normal playback.
Pause and Frame-by-Frame playback
Press PAUSE to pause, then
press PAUSE repeatedly.
Press PLAY ( ) to resume
normal playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
– Playback –
Playback Features
Slow-motion
Press PLAY ( ) on the
Remote.
• Playback will proceed at
1/10 th of the normal speed.
• Press PLAY ( ) to resume
normal playback.
OR Press Play ( ) on the
Adjusting tracking condition
VCR.
– Tracking Adjustment
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic
tracking starts working and continuously analyzes the signal
to enable optimum picture quality during playback.
Manual tracking adjustment
NOTE:
During slow motion picture, some noise might appear on
the TV screen. Use the SET–/+ on the Remote to eliminate
the noise.
If automatic tracking cannot eliminate noises well during
playback, press SET –/+ on the Remote to eliminate the
noises. Press it briefly for a fine adjustment, or press and
hold for a coarse adjustment.
Speed search
• Press SP/EP on the Remote again to reactivate automatic
tracking.
Press REW (
) or FF
OR Press REW (
) or
(
) on the Remote.
FF ( ) on the VCR.
• Press PLAY ( ) to resume
normal playback.
Variable speed search
Playing back tape repeatedly
Press REW (
) or FF
OR Press REW (
) or FF
– Auto Repeat Play
(
) repeatedly on the
(
) repeatedly on
Remote.
the VCR.
Access Menu screen
1
• Press PLAY ( ) to resume
normal playback.
• Each time you press REW
Press MENU on the Remote.
Press SET –/+ to select “AUTO
REPEAT”.
(
) or FF (
) the
playback speed changes.
Select ON/OFF
Press ENTER to select “ON” or
“OFF”.
Press MENU to return to normal
screen.
2
TAPE SPEED
PICTURE SEARCH SPEED
PRESS ONCE
3X
9X
PRESS TWICE
5X
15X
SP
EP
When the tape is not running
Rewind/fast-forward
Start Auto Repeat Play
3
Press PLAY. The tape will play
over and over until the repeat
mode is canceled.
Press REW (
) or FF
OR Press REW (
) or FF
) on the VCR.
(
) on the Remote.
(
Eject the tape
Press STOP/EJECT (I/ ) on
the VCR.
• You can also eject the
cassette when the VCR is
turned off.
Turn off the VCR
Press POWER on the
Remote.
OR Press POWER ( /l) on
the VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Features
Recording
Specifying recording length
It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
Accidental erasure prevention
- Instant Timer Recording (ITR)
The Instant Timer Recording feature provides a simple
and convenient way to make a timed
recording.
To prevent accidental recording on a recorded
cassette, remove its record safety tab.
To record on it later, cover the hole
with adhesive tape.
EXAMPLE: Instant Timer Recording for 30 minutes.
Record safety tab
When a TV is connected with an audio/video cable, turn the
TV on and select the video input mode on the TV.
Basic Recording
Load a cassette
1
Load a cassette tape with the
1
Make sure the record safety tab is intact. If not, cover the
hole with adhesive tape before inserting the cassette.
• The VCR turns on, and the counter
is reset, automatically.
erase prevention tab intact. The
clock display will change in the
counter display.
• If you press any operation buttons
while the cassette is not loaded,
Press SP/EP to select the desired
2
“
“ will flash on the screen for 4
tape speed SP or EP.
The counter and SP or EP will
appear on the screen for about 4
seconds.
seconds.
2 Select recording channel
Press CH–/+ or the Number keys on
00 : 00 : 00 SP
the Remote [CH–/+ on the VCR].
Press the Number keys or CH –/+
to select the channel to be
recorded.
3
• If you connect the TV and the VCR
only using the RF connection, press
TV/VCR on the Remote so that the
TV/VCR indicator lights to view the program to be recorded.
The channel number will appear
on the screen and display for
about 4 seconds.
Set tape speed
Press SP/EP.
3
ITR 0 : 30
CH 125
Press REC on the VCR or while
holding REC, press PLAY ( ) on
4
the Remote to begin recording.
00 : 00 : 00 SP
Press REC on the VCR again to
stop recording after 30 minutes.
Each additional press of REC will
increase recording time as shown in the chart below, up
to a maximum of 6 hours. The ITR and recording time
will appear on screen for about 4 seconds.
4
Start recording
On the VCR, press REC. Or on the
Remote, while holding REC, press
PLAY ( ).
The REC indicator will light.
NOTES: • Press REC to increase
the time needed for
recording (See the
chart).
Press
Recording time
NORMAL REC
0:30
once
During recording
Pause recording
twice
3 times
4 times
5 times
6 times
7 times
8 times
9 times
1:00
• To cancel ITR, press
STOP ( ) or turn off
the power.
1:30
Press PAUSE.
2:00
• Press PAUSE on the Remote or
REC on the VCR to resume
recording.
3:00
4:00
5:00
• You can select channel in the
recording pause mode.
6:00
10 times NORMAL REC
Stop recording
Watching one program while recording another
During recording…
• If you connect the TV and the VCR only using the RF
connection to view pictures from the VCR, press TV/VCR
on the Remote so that TV/VCR indicator goes off. (The TV
broadcast being recorded disappears.)
OR Press STOP/EJECT
(I/ ) on the VCR.
Press STOP ( ) on the
Remote.
• If you are using the AV connection to view pictures from
the VCR, change the TV’s input mode from AV to TV.
Then, select the channel you want to watch, on the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CORRECT THE SETTINGS
When setting the Timer Recording, press ENTER until the
desired setting blinks, then re-enter the setting using SET –/+.
When finished, press ENTER.
Timer Recording
Timer recording can be programmed on-screen with
the remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1
month.
NOTES: • The VCR cannot be used while the TIMER indicator
is lit.
NOTES:
• After timer recording is completed, the VCR turns off
automatically.
• After a power failure or disconnection of the
power plug, all programmed recording settings
must be reset upon resumption of power. In this
case, reset the clock and reprogram any timer
recordings.
• Press CANCEL to move cursor backward for
correction.
• You can program the timer recording while a regular
recording is in progress; the menu screens will not be
recorded.
• The timer recording will start at 5 seconds before the time
you predetermined.
EXAMPLE: Program a timer recording for the 26th day,
channel 125 (CATV), 11:00 - 11:30 PM on timer program
number 1 (Tape speed: EP).
TO SET DAILY/WEEKLY TIMER
When setting the date in step 3 in the Setting the Timer
Recording section, press SET – repeatedly.
The setting changes as follows:
When a TV is connected with an audio/video cable, turn the
TV and this VCR on and select the video input mode on the
TV.
Example
Press MENU on the Remote.
1
Check the “TIMER REC SET”
option is selected, then press
ENTER.
The current day (Friday)
SU-SA (Sunday to Saturday)
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
One month later
minus one day
Press SET –/+ to select one of
the program lines, then press
ENTER.
2
WKL-WE
(Weekly Wednesday)
Press SET –/+ to select the
date, then press ENTER.
3
4
TO CONFIRM THE SETTINGS
Set the start time, end time,
channel and tape speed as in
step 3.
Press SET –/+ to select the
“TIMER REC SET” option in the
MENU. Then press ENTER to
display the timer program list.
Press MENU twice to return to
the normal screen.
NOTE: To record from external
source, press SET –/+
and set the channel to
"L". "L" will appear next
to CH 125 (or 69).
To enter other programs,
repeat step 2 through 4. Or,
press MENU twice to return
to the normal screen.
5
6
TO CANCEL A PROGRAM
Press the SET –/+ to select the
“TIMER REC SET” option in the
MENU. Then press SET –/+ to
select the unnecessary program,
and press CANCEL to cancel the
program.
Press TIMER on the Remote.
The power will go off, the
TIMER indicator will light and
the VCR stands by for
recording.
To use the VCR while it is in timer recording standby mode
Press TIMER. After you use the VCR, press TIMER again
to put the VCR into timer recording standby mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
– Timer Recordings –
IF THE PROGRAM OVERLAPS ANOTHER
Other Functions
NOTE: Do not overlap programs as portions of the
conflicting programs will be lost. The first
recording time has priority over the next recording
time as shown in the diagram.
BLUE BACK — ON/OFF
When this function is set to “ON”, the TV screen becomes all
blue in the following case:
When receiving a channel not in use.
1
Press MENU on the remote. Press SET –/+ to select
8 : 00
9 : 00
10 : 00
11 : 00
Program 1
Program 2
“SYSTEM SETUP”.
2 Press SET –/+ to select “NO NOISE BACKGROUND”.
3
4
Deleted Parts
Program 3
Press ENTER to select “ON”.
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
Press MENU to return to normal screen.
STEREO RECORDING AND PLAYBACK
NOTES: • The everyday/every week recording can be made
continuously until the recording is canceled or
the tape reaches the end.
RECORDING STEREO BROADCASTS
The VHS Hi-Fi audio system permits high fidelity recording of
MTS STEREO TV broadcasts.
• During timer recording, the automatic rewinding
mechanism does not function.
When a MTS STEREO broadcast is
STEREO
received, the STEREO will appear on the
screen for about 4 seconds and the
program can be viewed or recorded in
stereo.
The Hi-Fi STEREO recording procedure
is the same as for normal recordings.
NOTE: When using a CATV system, stereo TV programs may be
transmitted over a mono cable channel. In this case the word
"STEREO" will not appear and the sound will be in mono.
OUTPUT SELECTION
When viewing an MTS STEREO TV program, or playing a
prerecorded VHS Hi-Fi STEREO videotape, press A.MONITOR to
select how the audio will be heard through the speakers. Normally
set to the Hi-Fi STEREO position, this button can be set to the
MONO position if the stereo broadcast or videotape audio is of
poor quality. The "R" and "L" positions allow the audio from the
Right or Left Hi-Fi channel to be heard over both TV speakers.
This button has no effect when viewing a MONO videotape or TV
program. Each time when you press the button, OUTPUT
SELECTION display appears on the screen for several seconds.
Refer to the chart below.
OUTPUT
SELECTION
SOUND HEARD ON BOTH
SPEAKERS
STEREO
L ch
R ch
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
MONO
NOTES: • When playing back a tape that is not recorded in
Hi-Fi stereo mode, the audio will automatically be
monaural.
• When listening to a VHS Hi-Fi video tape or MTS
broadcast through the VHF/UHF jack (Audio/
Video cord not connected), the sound will be
monaural.
Download from Www.Somanuals.com. All Manuals Search And Download.
– Other Functions –
Editing
SEPARATE AUDIO PROGRAM (SAP)
Your VCR is fitted with an SAP broadcast system which enables
you to switch to a SEPARATE AUDIO PROGRAM when viewing a
selected channel.
You can use your VCR as the playback or recording VCR.
You can use a camcorder as the playback VCR and your VCR
as the recording VCR. Refer also to the other components’
instruction manuals for connection and its operations.
This function applies only when the program is broadcast in
multi-languages through the SAP broadcast system.
When a TV is connected with an audio/video cable, turn the TV and
this VCR on, and select the video input mode the TV.
1
Make connections
Example: When using this VCR as the playback VCR
Press MENU on the Remote.
1
Press SET –/+ to select “SAP”
option.
Press ENTER to select “ON”
This VCR (for playback)
To audio/video out
2
position.
Press MENU to return to
normal screen.
3
Audio/video cable (not
supplied)
LISTENING TO SAP
When the VCR is turned on or a channel selection is made, make
certain "SAP" appears on the screen for about 4 seconds.
This means that the "Separate Audio Program" broadcasting is available.
STEREO SAP
SAP
To audio/video input
OR
Another VCR (for recording)
DAYLIGHT SAVING TIME SETTING
You can set the Daylight saving time automatically or manually.
Press MENU. Press SET –/+ to select
“SYSTEM SETUP” option, then press
ENTER.
1
• When using this VCR as the recording VCR, connect this
VCR’s audio/video input connectors to the audio/video
output connectors on the other VCR. If the playback VCR
is monaural, connect the audio output connector on the
playback VCR to the left audio input connector on this
VCR.
Press SET –/+ to select “DAYLIGHT
SAVING TIME” option, then press
ENTER.
2
3
Press SET –/+ to select one of the
options, then press ENTER. Press
MENU until the MENU screen is
cleared.
2 Load cassettes
Insert the playback cassette into the playback VCR and the
cassette to be recorded on into the recording VCR.
ON:
for manual setting
(forward one hour)
OFF: for manual setting
(back one hour)
AUTO: for automatic setting
(read XDS in the signal)
3
Select input mode on recording VCR
When you want to set the Daylight Saving
Time manually, on the first Sunday in April
you set to “ON”, and on the last Sunday in
October you set to “OFF”.
Select the correct external input on the recording VCR.
On this VCR (when using this VCR as the recording VCR);
Select “L” — when connecting the other VCR to the audio/video
input connectors on the front panel.
NOTES: • When shipped from factory, the DAYLIGHT SAVING
TIME option is set to AUTO position.
Press O (AUX) or CH–/+ on the Remote [CH–/+ on the VCR].
• When the clock is not set, Daylight Saving Time setting is
not available.
4
Start playback
• When there is no Daylight Saving Time in your area, al-
ways select OFF position in step 3.
Press PLAY ( ) on the playback VCR.
JVC TV Remote Control
CH –/+ and TV VOL –/+) of a remote controllable JVC TV without setting.
5
Start recording
This Remote can control some functions (TV POWER, INPUT, TV
Press REC on the recording VCR.
NOTE:
•
•
It’s not possible to operate a unit not equipped with a remote sensor.
This Remote can control a JVC TV only.
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Requesting Service
Make sure by first checking the following points.
SYMPTOM
POWER
CAUSE
POSSIBLE SOLUTION
Connect the AC power cord to the AC
outlet.
Insert a video cassette.
The AC power cord is not connected.
Cassette is not inserted.
No power.
Although the power is on, it
does not operate.
TV BROADCAST RECEPTION
Antenna connection is not correct.
Antenna cable is disconnected.
The video channel is not in the correct
position.
Connect it correctly.
Reconnect the antenna cable.
Set it to CH 3 or 4.
A TV program that is selected by
the VCR does not appear on the
screen.
The TV is not set to the video channel
3 or 4.
Set the TV channel selector to the 3 or 4
position.
The TV/VCR selector is set at TV mode
(The TV/VCR indicator is not lit).
Press the TV/VCR selector button (The TV/
VCR indicator will light).
INPUT is set to the LINE mode.
Press the Number key or CH –/+ button to
select your desired TV program.
The TV/CATV menu option setting.
A TV program selected by the
VCR does not appear in color.
Set the TV/CATV menu option to select TV
or CATV mode.
RECORDING
Place a piece of vinyl tape over the gap.
The erase prevention tab of the video
cassette is broken off.
TV recording does not work.
Press the Number key or CH –/+ button to
select your desired TV program.
INPUT is set to the LINE mode.
Reset the present time.
The time is not set correctly.
Set the start/end time.
The recording start/end time is not set
correctly.
Timer recording does not work.
Press the TIMER button (The TIMER
indicator is lit).
The TIMER button has not been
pressed (The TIMER indicator is not lit).
PLAYBACK
No picture on screen when
playing back a recorded tape.
The TV is not set to the video channel 3
or 4.
Set to the video channel 3 or 4 or
adjust the fine tuning button on your
TV set.
Tracking adjustment beyond range of
automatic tracking circuit.
Adjust tracking manually using the SET – or
+ buttons on the remote control.
Noise bars on screen.
Video heads are dirty.
The tape is worn or damaged.
Have the video heads cleaned.
Try another tape.
REMOTE CONTROL
It is not aimed at the remote sensor.
Aim it at the remote sensor.
Distance too far or too much light in
the room.
Operate within 15 feet (5 meters) reduce
the light in the room.
There is an obstacle in the path of the
beam.
Clear the path of the beam.
Remote control does not work.
The batteries are weak.
The +, – polarity of the batteries are
not inserted correctly.
Replace the batteries.
Insert correctly.
TV programs cannot be seen
using the TV selector.
Set to TV, or turn off the VCR power
button.
The TV/VCR function is in the VCR
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GENERAL
:
AC 120 V, 60 Hz
Power requirement
Power consumption
Power on
:
:
9 W
1.7 W
Power off
Temperature
Operating
:
:
:
:
:
:
5°C to 40°C (41°F to 104°F)
–20°C to 60°C (–4°F to140°F)
Horizontal only
360 mm x 95 mm x 222.5 mm (14-3/16" x 3-3/4" x 8-3/4")
3.2 kg (7.1 lbs)
VHS NTSC standard
Storage
Operating position
Dimensions (W x H x D)
Weight
Format
Maximum recording time
SP
:
:
210 min. with ST-210 video cassette
630 min. with ST-210 video cassette
EP
VIDEO/AUDIO
:
NTSC-type color signal and EIA monochrome signal, 525 lines/60 fields
Signal system
Recording/Playback
system
:
:
:
DA-4 (Double Azimuth) head helical scan system
42 dB
230 lines
Signal-to-noise ratio
Horizontal resolution
Frequency range
Normal audio
Hi-Fi audio
:
:
:
100 Hz to 10,000 Hz
20 Hz to 20,000 Hz
RCA connectors (IN x 1, OUT x 1)
Input/Output
TUNER
:
Frequency-synthesized tuner
Tuning system
Channel coverage
VHF
:
:
:
:
Channels 2–13
Channels 14–69
UHF
113 Channels
CATV
RF output
Channel 3 or 4 (switchable; preset to Channel 3 when shipped) 75 ohms,
unbalanced
TIMER
:
:
:
Quartz
Clock reference
1-month programmable timer/8 programs
Approx. 5 sec.
Program capacity
Memory backup for timer
ACCESSORIES
:
RF cable (F-type), Infrared remote control unit, “AAA” battery x 2
Provided accessories
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR SERVICING (Only in U.S.A.)
HOW TO LOCATEYOUR JVC SERVICE CENTER
TOLL FREE: 1-800-537-5722
Dear Customer,
In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the
event that repair is necessary, or for the address nearest your location within the Continental United States, please call 1-800-
Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and
production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is
world famous. The JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
10 New Maple Avenue
Pine Brook, NJ 07058-9641
Don’t service the product yourself.
ACCESSORIES
To purchase accessories for your JVC product, you may
contact your local JVC Dealer.
From the 48 Continental United States call toll free:
CAUTION
To prevent electrical shock, do not open the cabinet. There
are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY (Only in U.S.A.)
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase
for the period as shown below. (“The Warranty Period”)
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN COMMON-
WEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and
replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for
replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC
authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered
on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service
center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill
of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be
given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service,
or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with,
defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO
THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER DAMAGES,
WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR
DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS
AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE,
ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts,
so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, New Jersey 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF REFUR-
BISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED
WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
Download from Www.Somanuals.com. All Manuals Search And Download.
|