JVC Stereo System CA MXG51R User Manual

COMPACT COMPONENT SYSTEM

CA-MXG51R

DISC CHANGE

STANDBY

ECO

STANDBY/ON

PLAY

EXCHANGE

CD-R/

RW PLAYBACK

SOUND

MODE

COMPACT COMPONENT SYSTEM MX-G51R

COMPACT

DIGITAL AUDIO

SUBWOOFER

LEVEL

PRESET

STANDBY/ON

SET

SUBWOOFER

LEVEL

SLEEP

AUX

CANCEL

/DEMO

SOUND

MODE

PHONES

TUNING

FM MODE

CLOCK

TIMER

+10

DISPLAY

REPEAT PROGRAM RANDOM

REC START CD

FADE

MUTING PTY/EON

–

SELECT+

FADE

DISPLAY MODE PTY

EON

SELECT

TAPE

FM/AM

TAPE

TAPE A/B MUTING

/STOP

REC START DUBBING

DISC SKIP

VOLUME

EJECT

VOLUME

–

FULL - LOGIC CONTROL

CD SYNCHRO RECORDING

PLAY

REC/PLAY

RM–SMXG51R REMOTE CONTROL

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

LVT0692-009A

[B]

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,

care must be taken if you are to obtain the best results and safety is to be assured.

✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮

Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment)

are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or

changing connections.

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off,

withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation

or has a standby mode.

Switch off using the switch on the equipment and make sure that your family know how to do this.

Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is

illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s

approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result

in a fatal electrical shock.;

— NEVER guess or take chances with electrical equipment of any kind

— it is better to be safe than sorry!

– G-2 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

We would like to thank you for purchasing one of our JVC products.

Before operating this unit, read this manual carefully and thoroughly to

obtain the best possible performance from your unit, and retain this manual

for future reference.

Power sources

• When unplugging from the wall outlet, always pull the

plug, not the AC power cord.

About This Manual

This manual is organized as follows:

• The manual mainly explains operations using the

buttons and controls on the unit. You can also use the

buttons on the remote control if they have the same or

similar names (or marks) as those on the unit.

If operation using the remote control is different from

that using the unit, it is then explained.

• Basic and common information that is the same for many

functions is grouped in one place, and is not repeated in

each procedure. For instance, we do not repeat the

information about turning on/off the unit, setting the

volume, changing the sound effects, and others, which are

explained in the section “Common Operations” on pages 9

and 10.

DO NOT handle the AC power cord with wet

hands.

Moisture condensation

Moisture may condense on the lens inside the unit in the

following cases:

• After starting heating in the room

• In a damp room

• If the unit is brought directly from a cold to a warm place

Should this occur, the unit may malfunction. In this case,

leave the unit turned on for a few hours until the moisture

evaporates, unplug the AC power cord, and then plug it in

again.

• The following marks are used in this manual:

Gives you warnings and cautions to prevent

damage or risk of fire/electric shock.

Also gives you information which is not good

for obtaining the best possible performance

from the unit.

Others

• Should any metallic object or liquid fall into the unit,

unplug the unit and consult your dealer before operating

any further.

• If you are not going to operate the unit for an extended

period of time, unplug the AC power cord from the wall

outlet.

Gives you information and hints you had better

know.

DO NOT disassemble the unit since there are no

user serviceable parts inside.

Precautions

If anything goes wrong, unplug the AC power cord and

consult your dealer.

Installation

• Install in a place which is level, dry and neither too hot nor

too cold — between 5˚C (41˚F) and 35˚C (95˚F).

• Install the unit in a location with adequate ventilation to

prevent internal heat built-up in the unit.

• Leave sufficient distance between the unit and the TV.

• Keep the speakers away from the TV to avoid interference

with TV.

DO NOT install the unit in a location near heat

sources, or in a place subject to direct sunlight,

excessive dust or vibration.

– 1 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Location of the Buttons and Controls ....................... 3 Playing Back Tapes ................................................... 17

Front Panel ................................................................. 3

Remote Control .......................................................... 5

Playing Back a Tape ................................................. 17

Recording .................................................................. 18

Getting Started............................................................ 6

Recording a Tape on Deck B.................................... 18

Dubbing Tapes.......................................................... 19

CD Synchro Recording ............................................. 19

Unpacking .................................................................. 6

Putting the Batteries into the Remote Control ........... 6

Connecting Antennas ................................................. 6

Connecting Speakers .................................................. 7

Connecting Other Equipment..................................... 8

Cancelling the Display Demonstration ...................... 8

Using the Timers ....................................................... 20

Using Daily Timer .................................................... 20

Using Recording Timer ............................................ 21

Using Sleep Timer .................................................... 22

Timer Priority ........................................................... 22

Common Operations .................................................. 9

Turning On or Off the Power ....................................... 9

Saving the Power Consumption While on Standby

Maintenance .............................................................. 23

Troubleshooting ........................................................ 24

Additional Information ............................................ 25

Specifications............................................................. 26

— ECO-mode ....................................................... 9

Setting the Clock ........................................................ 9

Selecting the Sources................................................... 9

Adjusting the Volume ............................................... 10

Reinforcing the Bass Sound ..................................... 10

Selecting the Sound Modes ...................................... 10

Listening to FM, MW, and LW Broadcasts............ 11

Tuning in a Station ................................................... 11

Presetting Stations .................................................... 11

Tuning in a Preset Station ........................................ 11

Receiving FM Stations with RDS ............................ 12

Changing the RDS Information ............................... 12

Searching for Programs by PTY Codes

(PTY Search) ...................................................... 12

Switching to a Program Type of Your

Choice Temporarily ............................................ 13

Playing Back CDs ..................................................... 14

Loading CDs ............................................................ 14

Playing Back the Entire Discs

— Continuous Play............................................. 14

Basic CD Operations ................................................ 15

Programming the Playing Order of the Tracks

— Program Play ................................................. 15

Playing at Random — Random Play ....................... 16

Repeating Tracks or CDs — Repeat Play ................ 16

Prohibiting Disc Ejection — Tray Lock................... 16

– 2 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Location of the Buttons and Controls

Become familiar with the buttons and controls on your unit.

Front Panel

DISC CHANGE

STANDBY

ECO

STANDBY/ON

;

PLAY & EXCHANGE

CD-R

RW PLAYBACK

SOUND

MODE

COMPACT COMPONENT SYSTEM

MX-G51R

COMPACT

DIGITAL AUDIO

SUBWOOFER

LEVEL

PRESET

SET

CANCEL

/DEMO

PHONES

TUNING

CLOCK

TIMER

DISPLAY

REPEAT PROGRAM RANDOM

REC START CD

/STOP

DISPLAY MODE PTY / EON

SELECT

TAPE A

TAPE B

REC START DUBBING

EJECT

FULL - LOGIC CONTROL

CD SYNCHRO RECORDING

PLAY

REC/PLAY

– 3 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Continued

Display Window

See pages in the parentheses for details.

d PRESET +/– buttons (11)

4 / ¢ (reverse search/forward search) buttons

Front Panel

(9, 15, 20 – 22)

f SUBWOOFER LEVEL control (10)

g VOLUME control (10)

1 Carrousel

STANDBY/ON button and STANDBY lamp (9)

h TUNING +/– buttons (11)

3 ECO button (9)

1 / ¡ (fast rewind/fast forward) buttons (15, 17)

4 7 (stop) button (14 – 19)

j TAPE A button (17)

5 SET button (9, 11, 15, 20 – 22)

6 CANCEL button (9, 16, 21, 22)

DEMO button (8)

TAPE B button (17)

k REC START/STOP button (18)

CD REC START button (19)

7 Display window

DUBBING button (19)

l Deck B cassette holder (17 – 19)

• Pressing the EJECT 0 portion opens the holder.

8 TAPE 3 button and lamp (9, 17, 19)

Pressing this button also turns on the unit.

9 CD 6 (play/pause) button and lamp (9, 14 – 16)

Pressing this button also turns on the unit.

p FM/AM button and lamp (9, 11)

Pressing this button also turns on the unit.

q DISPLAY button (9)

Display window

1 Timer indicators

w AUX button and lamp (9)

• DAILY (daily timer), REC (recording timer), SLEEP

Pressing this button also turns on the unit.

e PHONES jack (10)

r CLOCK/TIMER button (9, 20 – 22)

t RDS operation buttons (12)

• DISPLAY MODE, PTY/EON, and SELECT +/–

y REPEAT button (16)

(sleep timer), and

2 Tape operation indicators

• A/B (operating deck), REC (recording), and 2 / 3 (tape

running) indicators

3 CD play mode indicators

(timer) indicators

• REPEAT (1, 1 DISC, ALL DISC), PRGM (program),

and RANDOM indicators

4 Tuner operation indicators

• MONO and ST (stereo) indicators

5 SOUND MODE indicator

6 Disc indicators

7 Volume level, Subwoofer level, and Sound Mode pattern

indicators

8 SUBWOOFER LEVEL indicator

9 Main display

• Shows the source name, frequency, etc.

p RDS operation indicators

• RDS, EON, and TA indicators

q CD track number indicators

PROGRAM button (15)

RANDOM button (16)

u Deck A cassette holder (17, 19)

• Pressing the 0 EJECT portion opens the holder.

i 0 (Carrousel open/close) button (14 – 16)

Pressing this button also turns on the unit.

o Disc number buttons and lamps (CD1, CD2, and CD3)

(14, 15, 19)

Pressing one of these buttons also turns on the unit.

; DISC CHANGE button (14, 15)

a Remote sensor

s SOUND MODE control (10)

– 4 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Control

STANDBY/ON button (9)

2 SLEEP button (22)

3 AUX button (9)

Pressing this button also turns on the unit.

4 Number buttons (11, 15)

5 TAPE 3 button (9, 17)

STANDBY/ON

SUBWOOFER

LEVEL

SLEEP

AUX

Pressing this button also turns on the unit.

6 FM/AM button (9, 11)

SOUND

MODE

Pressing this button also turns on the unit.

7 CD 6 button (9, 14 – 16)

Pressing this button also turns on the unit.

8 4 (fast rewind/reverse search) button

(11, 15, 17)

9 VOLUME – button (10)

p SUBWOOFER LEVEL button (10)

q SOUND MODE button (10)

w FM MODE button (11)

e RDS operation buttons (12)

• DISPLAY MODE, PTY/EON, and SELECT +/–

r TAPE A/B button (17)

t FADE MUTING button (10)

y DISC SKIP button (14)

FM MODE

+10

DISPLAY

MODE

PTY/EON

–SELECT

FADE

FM/AM

TAPE

TAPE A/B MUTING

DISC SKIP

VOLUME

–

u VOLUME + button (10)

i ¢ (fast forward/forward search) button

(11, 15, 17)

o 7 (stop) button (14 – 19)

RM–SMXG51R REMOTE CONTROL

DISC CHANGE

STANDBY

ECO

STANDBY/ON

PLAY

EXCHANGE

CD-R

/RW PLAYBACK

SOUND

MODE

COMPACT COMPONENT SYSTEM MX-G51R

COMPACT

DIGITAL AUDIO

SUBWOOFER

LEVEL

PRESET

SET

CANCEL

/DEMO

PHONES

TUNING

CLOCK

TIMER

DISPLAY

REPEAT PROGRAM RANDOM

REC START CD

DISPLAY MODE PTY

EON

SELECT

TAPE

/STOP

REC START DUBBING

EJECT

FULL - LOGIC CONTROL

CD SYNCHRO RECORDING

PLAY

REC/PLAY

PLAY

When using the remote control, point it at

the remote sensor on the front panel.

– 5 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

Continued

Unpacking

Connecting Antennas

After unpacking, check to be sure that you have all the

following items.

FM antenna

The number in the parentheses indicates the quantity of the

pieces supplied.

FM antenna (supplied)

• AM (MW/LW) loop antenna (1)

• FM antenna (1)

ANTENNA

FM [75

]

• Remote control (1)

• Batteries (2)

If any is missing, consult your dealer immediately.

Putting the Batteries into the Remote Control

1 Attach the FM antenna to the FM [75 Ω]

Insert the batteries — UM-4/AAA/IEC R03 — into the

remote control, by matching the polarity (+ and –) on the

batteries with the + and – markings on the battery

compartment.

When the remote control can no longer operate the unit,

replace both batteries at the same time.

coaxial terminal.

2 Extend the FM antenna.

3 Fasten it up in the position which gives you

the best reception, then fix it on the wall, etc.

About the supplied FM antenna

The FM antenna supplied with this unit can be used as temporary

measure. If reception is poor, you can connect an outdoor FM

antenna.

To connect an outdoor FM antenna

Before connecting it, disconnect the supplied FM antenna.

Outdoor FM antenna

(not supplied)

UM-4/AAA/IEC R03

ANTENNA

FM [75

]

• DO NOT use an old battery together with a new one.

• DO NOT use different types of batteries together.

• DO NOT expose batteries to heat or flame.

• DO NOT leave the batteries in the battery

A 75 Ω antenna with coaxial type connector (DIN 45325)

should be used.

compartment when you are not going to use the

remote control for an extended period of time.

Otherwise, it will be damaged from battery leakage.

– 6 –

Download from Www.Somanuals.com. All Manuals Search And Download.

AM (MW/LW) antenna

Connecting Speakers

Vinyl-covered wire

(not supplied)

ANTENNA

FM 75

[

]

Speaker cord

(blue/black)

Black

Speaker

cord

(red/black)

MAIN SPEAKER SUBWOOFER

[

]

[

]

4-8

6-16

Blue

Red

Black

Speaker cord

(blue/black)

Speaker cord

(red/black)

AM (MW/LW) loop

antenna (supplied)

From right

main

speaker’s

terminals

From right

subwoofer’s

terminals

1 Press and hold the clamp of the AM

terminals on the rear of the unit.

From left

subwoofer’s

terminals

From left

main

speaker’s

terminals

2 Insert the end of the AM (MW/LW) loop

antenna cord into the terminal.

3 Release the finger from the clamp.

1 Press and hold the clamp of the speaker

4 Turn the AM (MW/LW) loop antenna until

terminal on the rear of the unit.

you have the best reception.

2 Insert the end of the speaker cord into the

To connect an outdoor AM (MW/LW) antenna

When reception is poor, connect a single vinyl-covered wire

to the AM terminal and extend it horizontally. (The AM

(MW/LW) loop antenna must remain connected.)

terminal.

Match the polarity (colors): Blue (+) to blue (+) and black

(–) to black (–); Red (+) to red (+) and black (–) to black

(–).

3 Release the finger from the clamp.

For better reception of FM, MW, and LW

• Make sure the antenna conductors do not touch any other

terminals and connecting cords.

• Keep the antennas away from metallic parts of the unit,

connecting cords, and the AC power cord.

IMPORTANT: Use only speakers with the same speaker

impedance as indicated by the speaker terminals on the

rear of the unit.

– 7 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Connect an optical digital cord (not supplied) between the

optical digital input terminal on the other equipment and the

DIGITAL OUT [OPTICAL] terminal.

Connecting Other Equipment

You can connect both analog and digital equipment.

• DO NOT connect any equipment while the power

is on.

• DO NOT plug in any equipment until all

connections are complete.

NOW, you can plug in the unit and other

connected equipment FINALLY!

Cancelling the Display Demonstration

To connect an analog component

Be sure that the plugs of the audio cords are color coded:

White plugs and jacks are for left audio signals, and red ones

for right audio signals.

When connecting the AC power cord into a wall outlet, the

unit automatically starts display demonstration.

On the unit ONLY:

AUX IN

CANCEL

/DEMO

To cancel the display demonstration, press

DEMO.

When you press other buttons

Audio/video

equipment

The display demonstration stops temporarily. It will start

automatically again (if no operation is done for 2 minutes) until you

cancel it by pressing DEMO.

To audio output

For playing the other equipment through this unit,

connect between the audio output jacks on the other

equipment and AUX IN jacks by using audio cords (not

supplied).

To start the display demonstration manually

CANCEL

/DEMO

Press and hold DEMO again for more than 2

seconds.

To connect audio equipment with an optical digital

input terminal

You can record CD sound onto the connected digital

equipment.

DIGITAL OUT

Protective

plug

[

]

OPTICAL

Before connecting

the other equipment,

remove the

protective plug from

the terminal.

Audio equipment

with an optical digital

input

To optical

digital input

– 8 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Common Operations

Turning On or Off the Power

PRESET

2 Press 4 or ¢ to adjust the

hour, then press SET.

To turn on the unit, press

STANDBY

ECO

STANDBY/ON so that the STANDBY

STANDBY/ON

lamp goes off.

SET

• If you want to correct the hour after

pressing SET, press CANCEL. The

hour digits start flashing again.

To turn off the unit (on standby), press

STANDBY/ON again so that the

STANDBY lamp lights up.

STANDBY

ECO

STANDBY/ON

PRESET

3 Press 4 or ¢ to adjust the

minute, then press SET.

A little power is always consumed even while the unit is on

standby.

To switch off the power supply completely, unplug the AC

power cord from the AC outlet.

SET

When you unplug the AC power cord or if a power

failure occurs

The clock is reset to “– – : – –” soon, while the tuner preset stations

(see page 11) will be erased in a few days.

To check the clock time

DISPLAY

Press DISPLAY while playing any source.

• Each time you press the button, the source

indication and the clock time alternate on the

display.

Saving the Power Consumption While on

Standby — ECO-mode

To adjust the clock again

If you have adjusted the clock before, you need to press

CLOCK/TIMER repeatedly until “CLOCK” is selected.

• Each time you press the button, the clock/timer setting

modes change as follows:

You can save the power consumption only while the unit is

turned off (on standby).

STANDBY

To activate the ECO-mode, press ECO

ON TIME

REC

DAILY

ECO

STANDBY/ON

while the unit is turned off (on standby).

The display illumination (including the

display demonstration) disappears.

Canceled

CLOCK

ON TIME

If there is a power failure

The clock loses the setting and is reset to “– – : – –.” You need to set

the clock again.

To deactivate the ECO-mode, press ECO again.

The display illumination appears.

About ECO-mode

While ECO-mode is activated, the display demonstration is canceled

temporarily.

Selecting the Sources

To listen to the FM, MW or LW broadcasts, press FM/AM.

(See page 11.)

To play back CDs, press CD 6. (See pages 14 – 16.)

To play back tapes, press TAPE 3. (See page 17.)

To select the external equipment as the source, press AUX.

Setting the Clock

Before operating the unit any further, first set the clock built in

this unit. You can set the clock whether the unit is on or off.

On the unit ONLY:

CLOCK

TIMER

1 Press CLOCK/TIMER.

When you press the play button for a particular source (AUX,

FM/AM, CD 6, and TAPE 3), the unit turns on (and the

unit starts playing the source if it is ready — COMPU PLAY

CONTROL).

The hour digits start

flashing on the display.

– 9 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Volume

Selecting the Sound Modes

You can adjust the volume level only while the unit is turned

on.

This function only affects the playback sound, but does not

affect your recording.

Turn the VOLUME control clockwise to

increase the volume or counterclockwise

to decrease it.

You can select one of the 6 preset sound modes (3 surround

modes and 3 SEA — Sound Effect Amplifier — modes).

• The volume level can be adjusted in

32 steps (VOL MIN, VOL 1 — VOL 30,

and VOL MAX).

To select the sound modes, turn the

SOUND MODE control until the sound

mode you want appears on the display.

SOUND

MODE

When using the remote control, press VOLUME + to increase

the volume or press VOLUME – to decrease it.

SOUND MODE indicator

also lights up on the display

For private listening

Connect a pair of headphones to the PHONES jack. No sound

comes out of the speakers. Be sure to turn down the volume before

connecting or putting on headphones.

DO NOT turn off (on standby) the unit with the volume set

to an extremely high level; otherwise, a sudden blast of

sound can damage your hearing, speakers and/or

headphones when you turn on the unit or start playing

any source next time.

• As you turn the control, the sound modes change as

follows:

REMEMBER you cannot adjust the volume level while the

unit is on standby.

D.CLUB

HALL

STADIUM

ROCK

POP

(Dance CLUB)

OFF

(Canceled)

CLASSIC

To turn down the volume level temporarily

Press FADE MUTING on the remote control.

FADE

MUTING

Surround modes*:

D.CLUB: Increases resonance and bass.

HALL: Adds depth and brilliance to the sound.

The volume level gradually decreases to “VOL MIN.”

To restore the sound, press the button again.

STADIUM: Adds clarity and spreads the sound, like in an

Reinforcing the Bass Sound

outdoor stadium.

SEA (Sound Effect Amplifier) modes:

This function only affects the playback sound, but does not

affect your recording.

ROCK:

Boosts low and high frequency. Good for

acoustic music.

POP:

Good for vocal music.

Turn the SUBWOOFER LEVEL control

SUBWOOFER

LEVEL

CLASSIC: Good for classical music.

clockwise to increase the subwoofer

sound or counterclockwise to decrease it.

• The subwoofer level can be adjusted in 4

steps (LEVEL 1 — LEVEL 4.)

If you turn the control clockwise up to the

volume LEVEL 4, “MAX” flashes on the

display for a few seconds.

OFF: Cancels the sound mode.

* Surround elements are added to the SEA elements to create a

being-there feeling in your room.

When one of these modes is selected, the SOUND MODE

indicator lights up as —

SUBWOOFER LEVEL indicator always

lights up when the unit is on.

While one of the SEA modes (SEA elements without surround

elements) is selected, the SOUND MODE indicator lights up as

—

When using the remote control, press SOUND MODE to

adjust the sound mode.

• Each time you press the button, the sound modes change as

follows:

D.CLUB

HALL

STADIUM

ROCK

When using the remote control, press SUBWOOFER LEVEL

to adjust the subwoofer level. The subwoofer level changes as

LEVEL 1 = LEVEL 2 = LEVEL 3 = LEVEL 4 =

(back to the beginning).

(Dance CLUB)

OFF

(Canceled)

CLASSIC

POP

– 10 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to FM, MW, and LW Broadcasts

Tuning in a Station

SET

2 Press SET.

1 Press FM/AM.

The unit automatically turns on and tunes

in the previously tuned station (FM, MW

or LW).

• Each time you press the button, the

band changes among FM, MW, and LW.

3 Press PRESET + or PRESET –

PRESET

to select a preset number.

2 Start searching for stations.

On the unit:

Press and hold TUNING + or

TUNING – for more than 1

second.

TUNING

SET

4 Press SET again.

On the remote control:

Press and hold 4 or

¢ for more than 1 second.

The unit starts searching for stations

and stops when a station of sufficient

signal strength is tuned in.

The tuned station in step 1 is stored in the preset number

selected in step 3.

• Storing a new station on a used number erases the

previously stored one.

If a program is broadcast in stereo, the

ST (stereo) indicator lights up.

When you unplug the AC power cord or if a power

failure occurs

The preset stations will be erased in a few days. If this happens,

preset the stations again.

To stop during searching, press TUNING + or TUNING –

(or 4 or ¢ on the remote control).

When you press TUNING + or TUNING –

(or 4 or ¢ on the remote control) briefly and repeatedly

The frequency changes step by step.

Tuning in a Preset Station

To change the FM reception mode

1 Press FM/AM.

When an FM stereo broadcast is hard to receive or

The unit automatically turns on and

tunes in the previously tuned station

(FM, MW or LW).

FM MODE

noisy, press FM MODE on the remote control so that

“MONO” appears and the MONO indicator lights up

on the display. Reception improves.

• Each time you press the button, the

band changes among FM, MW, and

LW.

To restore the stereo effect, press FM MODE

again so that “STEREO” appears on the diplay and the

MONO indicator goes off from the display.

In this stereo mode, you can hear stereo sounds when a

program is broadcast in stereo.

2 Select a preset number.

On the unit:

PRESET

Press PRESET + or PRESET –.

Presetting Stations

You can preset 30 FM, 8 MW, and 7 LW stations.

In some cases, test frequencies have been already memorized

for the tuner since the factory examined the tuner preset

function before shipment. This is not a malfunction. You can

preset the stations you want into memory by following the

presetting method.

On the remote control:

Press the number buttons.

Ex.: For preset number 5, press 5.

For preset number 15, press +10

then 5.

For preset number 20, press

+10, then 10.

For preset number 25, press

+10, +10, then 5.

+10

•

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 1 again.

On the unit ONLY:

For preset number 30, press +10, +10, then 10.

1 Tune in the station you want to preset.

• See “Tuning in a Station” above.

– 11 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Receiving FM Stations with RDS

Continued

RDS allows FM stations to send an additional signal along

Searching for Programs by PTY Codes (PTY

Search)

with their regular program signals. For example, the stations

send their station names, as well as information about what

type of program they broadcast, such as sports or music, etc.

One of the advantages of RDS is that you can locate a

particular kind of program by specifying the PTY codes.

• For details on the PTY codes, see “Additional Information”

on page 25.

When tuned to an FM station which provides the RDS

service, the RDS indicator lights up on the display.

To search for a program using the PTY codes

REMEMBER you must preset FM RDS stations to use the

PTY codes. If not yet done, see page 11.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

With the unit, you can receive the following types of RDS

signals.

PS (Program Service):

Shows commonly known station names.

CT (Clock Time):

Shows clock time the station sends.

PTY / EON

RT (Radio Text):

1 Press PTY/EON.

Shows text messages the station sends.

EON (Enhanced Other Networks):

Provides the information about the types of the

programs sent by other RDS stations.

SELECT

2 Press SELECT + or SELECT –

until the PTY code you want

appears on the display.

More about RDS

• Some FM, MW, and LW stations do not provide RDS signals.

• RDS services vary among FM RDS stations. For details on RDS

services in your area, check with local radio stations.

• RDS may not work correctly if the received station is not

transmitting the signals properly or if the signal strength is weak.

• Each time you press the button, the PTY codes change

as follows:

Changing the RDS Information

You can see RDS information on the display while listening

to an FM station.

NEWS “ AFFAIRS “ INFO “ SPORT “

EDUCATE “ DRAMA “ CULTURE “

DISPLAY MODE

SCIENCE “ VARIED “ POP M “ ROCK M “

M.O.R. M “ LIGHT M “ CLASSICS “

OTHER M “ WEATHER “ FINANCE “

CHILDREN “ SOCIAL A “ RELIGION “

PHONE IN “ TRAVEL “ LEISURE “ JAZZ “

COUNTRY “ NATIONAL “ OLDIES “

FOLK M “ DOCUMENT “ (back to the beginning)

Press DISPLAY MODE.

• Each time you press the button, the display

changes to show the following information:

PS NAME

(Program Service Name)

(Radio Text)

(Clock Time)

Station frequency

(or preset channel no.)

* The clock time shown on the display is not the

same as CT (Clock Time) sent by the station.

PTY / EON

3 Press PTY/EON once again.

The preset FM stations appear on the display

with their preset numbers.

The unit searches 30 preset FM stations, stops

when it finds the one you have selected and tunes in that

station.

If no PS NAME, CT, or RT signals are sent by a station

“NO PS,” “NO CT” or “NO RT” appears in the main display.

• If no program is found, the unit returns to the last

received station.

To stop searching any time during the process

Press SELECT + or SELECT – while searching.

– 12 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Switching to a Traffic Announcement

Temporarily

How the EON function actually works:

CASE 1

By receiving EON data sent by FM RDS stations, the EON

function allows the unit to switch temporarily to a broadcast

of a traffic announcement from a different station.

• The EON function only works when you are listening to a

preset FM RDS stations providing EON data.

• The EON indicator lights while receiving a station with

EON data.

If there is no station broadcasting a traffic

announcement

The unit continues tuning in the current station.

When a station starts broadcasting a traffic announcement,

the unit automatically switches to the station. The TA

indicator starts flashing.

To activate the EON function

REMEMBER you must preset FM RDS stations to use the

EON function. If not yet done, see page 11.

When the program is over, the unit goes back to the

previously tuned station, but the EON function still

remains activated.

PTY / EON

CASE 2

1 Press and hold PTY/EON.

Each time you press and hold PTY/EON,

“TA ON” and “TA OFF” alternately appear

on the display.

If there is a station broadcasting a traffic

announcement

The unit tunes in the program. The TA indicator starts

flashing.

TA ON

TA OFF

When the program is over, the unit goes back to the

previously tuned station, but the EON function still

remains activated.

TA ON: Switches to a traffic announcement, if any.

TA OFF: This function is canceled.

CASE 3

If the FM station you are listening to is broadcasting a

traffic announcement

The unit continues to receive the station but the TA

indicator starts flashing.

When the program is over, the TA indicator stops flashing,

but the EON function still remains activated.

More about the EON function

• EON data sent from some stations may not be compatible with

this unit. In this case, the EON function may not work correctly.

• While listening to a program tuned in by the EON function, the

station does not change even if another network station starts

broadcasting a program of the same EON data.

• The EON function is canceled when you change the source to CD,

TAPE, or AUX, while it is temporarily canceled when you change

the source to MW or LW.

– 13 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Back CDs

Continued

This unit has been designed to playback the following CDs:

Audio CD, CD-R, and CD-RW.

About the disc indicators

Each disc indicator corresponds to the disc tray of the same number.

Continued use of irregular shape CDs (heart-shape,

octagonal, etc.) can damage the unit.

When playing a CD-R or CD-RW

Disc number

User-edited CD-Rs (Recordable) and CD-RWs

(Rewritable) can be played back only if they are already

“finalized.”

Disc indicator

Disc marker

• You can play back your original CD-Rs or CD-RWs

recorded in music CD format. (However, they may not

be played back depending on their characteristics or

recording conditions.)

• Before playing back CD-Rs or CD-RWs, read their

instructions or cautions carefully.

• The disc marker lights up for the disc number you have selected.

• The disc indicator rotates while the corresponding CD is being

played.

• The disc indicator goes off when the unit has detected that there is

no CD on the corresponding disc tray.

• Some CD-Rs or CD-RWs may not be played back on

this unit because of their disc characteristics, damage or

stain on them, or if the player’s lens is dirty.

• CD-RWs may require a longer readout time. (This is

caused by the fact that the reflectance of CD-RWs is

lower than for regular CDs.)

Playing Back the Entire Discs — Continuous

Play

You can play CDs continuously.

1 Load CDs.

Loading CDs

2 Press one of the disc

number buttons (CD1, CD2

or CD3) for the disc you

want to play.

1 Press 0.

The unit automatically turns on and the

carrousel comes out.

CD play starts from the first track of

the selected disc.

2 Place one or two discs correctly on the front

slots of the carrousel, with its label side up.

Track number of the currently playing disc is

flashing. (Track numbers exceeding 16 are

not displayed.)

INCORRECT

CORRECT

• When using a CD single (8 cm), place it on the inner

circle of the disc tray.

Track number

Elapsed playing time

DISC CHANGE

• Pressing CD 6 instead of the disc number buttons

3 If you wish to load a third disc,

starts playing back if a CD is on the tray.

press DISC CHANGE on the unit

or DISC SKIP on the remote

When you turn on the unit, ALL DISC indicator lights up on

the display automatically. If you do not want all the CDs to

play back, select 1 DISC by pressing REPEAT.

DISC SKIP

control.

The carrousel rotates by 120˚.

REPEAT 1

REPEAT 1 DISC

ALL DISC

1 DISC

4 Press 0 again.

REPEAT ALL DISC

The carrousel closes.

ALL DISC:

1 DISC:

Plays all loaded CD.

Plays back one CD.

To stop during play, press 7.

To remove the disc, press 0.

– 14 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming the Playing Order of the Tracks

— Program Play

CD playback sequence (when ALL DISC is selected)

When 3 CDs are loaded on the disc trays, they are played in one of

the following sequences.

• When CD1 is pressed : CD1 ] CD2 ] CD3 (then stops)

• When CD2 is pressed : CD2 ] CD3 ] CD1 (then stops)

• When CD3 is pressed : CD3 ] CD1 ] CD2 (then stops)

* When only 2 CDs are loaded, they are played in the same order,

but the disc tray without a CD is skipped.

You can arrange the order in which the tracks play before you

start playing. You can program up to 32 tracks.

• To use Repeat play (see page 16) for Program play, press

REPEAT after starting Program play.

On the unit ONLY:

1 Load CDs.

Basic CD Operations

• If the current playing source is not the CD player, press

CD 6, then 7 before going to the next step.

While playing a CD, you can do the following operations.

EAT PROGRAM RANDOM

2 Press PROGRAM so that

To exchange CDs during playback of another

Press DISC CHANGE to change the CD and the

carrousel comes out.

DISC CHANGE

“PROGRAM” appears on the

display.

If you change CDs during play, the current play

will not stop until all CDs you have changed are

played.

The PRGM (program) indicator also lights up on the

display.

To close the carrousel, press DISC CHANGE or 0.

To skip to the another CD in the carrousel

Press DISC SKIP on the remote control.

DISC SKIP

• If a program has been stored in memory, the program is

called up.

To stop play for a moment

Press CD 6.

While pausing, “PAUSE” appears on the

display.

3 Press one of the disc number

buttons (CD1, CD2 or CD3)

to select the disc number you

To resume play, press CD 6 again.

want to play.

To locate a particular point in a track

During play, press and hold 1 or ¡.

• 1: Fast reverses the disc.

Track number

TUNING

• ¡: Fast forwards the disc.

When using the remote control, press and

hold 4 or ¢.

To go to another track

Press 4 or ¢ repeatedly before or

during playback.

PRESET

Disc number

Program step number

• 4:Goes back to the beginning of the

current or previous tracks.

4 Press 4 or ¢ to select the track number,

then press SET.

• ¢:Skips to the beginning of the next or

Each time you select a track and press SET, the selected

track number is added to the CD track number indicator.

succeeding tracks.

If you press and hold 4 or ¢ on the unit before or

during play

PRESET

SET

You can change the tracks continuously.

To go to another track directly using the number buttons

Pressing the number button(s) before or

during play allows you to start playing the

track number you want.

Ex.: For track number 5, press 5.

For track number 15, press +10, then 5.

For track number 20, press +10, then 10.

For track number 32, press +10, +10,

+10, then 2.

+10

– 15 –

Download from Www.Somanuals.com. All Manuals Search And Download.

To stop during play, press 7.

5 Program other tracks you want.

• To program tracks from the same disc, repeat step 4.

• To program tracks from a different disc, repeat steps 3

and 4.

• Random play also stops when 0 is pressed.

To exit from Random play mode, press RANDOM again

during play so that the unit enters Continuous play mode.

To use Random play mode, you have to exit from the

Program play mode.

6 Press CD 6.

The tracks are played in the order you

have programed.

If you press ¢ or 4

Skips to the next track selected randomly.

To stop during play, press 7.

To exit from Program play mode, press PROGRAM again

before or after play so that the unit enters Continuous play

mode. (The program you have made is stored in memory

until you turn off the unit or erase the program.)

Repeating Tracks or CDs — Repeat Play

You can have all the CDs, the program or the individual track

currently playing repeat as many times as you like.

To modify the program

REPEAT PROGRAM

To repeat play, press REPEAT during or before

playing.

• Each time you press the button, Repeat play

mode changes as follows, and the following

indicator lights up on the display:

CANCEL

/DEMO

Before playing, you can erase the programed

tracks shown on the display by pressing CANCEL.

• Each time you press the button, the last programmed

track is erased from the program.

To check the program during play, press ¢ (or 4) so that the

playing track will change according to the program (or reverse)

order.

REPEAT 1

ALL DISC

1 DISC

REPEAT ALL DISC

REPEAT 1 DISC

REPEAT 1:

Repeats one track on one CD.

To add tracks in the program before play, simply select the disc

numbers and/or track numbers you want to add by following steps 3

and 4 of the programming procedure on page 15.

REPEAT 1 DISC*: Repeats all the tracks on one CD.

REPEAT ALL DISC: Repeats all the tracks on all the CDs.

REPEAT 1 DISC is not used for Program play.

To erase the entire program before or during play, press 7 twice.

• Ejecting a carrousel will also erase the stored memory.

To cancel Repeat play, press REPEAT repeatedly until the

REPEAT indicator (REPEAT 1, REPEAT 1 DISC or

REPEAT ALL DISC) goes off from the display.

• Repeat play and Random play cannot be used at the same

time.

If you try to program a 33rd track

“FULL” will appear on the display.

Prohibiting Disc Ejection — Tray Lock

If your entry is ignored

You have tried to program a track from an empty tray, or a track

number that does not exist on the CD. Such entries are ignored.

You can prohibit CD ejection from the unit and lock CDs.

• This operation is possible only while the unit is on with CD

selected as the source.

Playing at Random — Random Play

The tracks of the selected CD will play at random.

On the unit ONLY:

To prohibit disc ejection, press 0 for the carrousel while

holding 7.

1 Load a CD.

• If the current playing source is not the CD player, press

CD 6, then 7 before going to the next step.

“LOCKED” appears for a while, and the carrousel is locked.

To cancel the prohibition and unlock the CDs, press 0 for

the carrousel while holding 7.

“UNLOCKED” appears for a while, and the carrousel is

unlocked.

RANDOM

2 Press RANDOM so that “RANDOM”

appears on the display.

The RANDOM indicator also lights up on the

display.

If you try to eject CDs

“LOCKED” appears to inform you that the Tray Lock is in use.

• The tracks are played automatically at random. Random

play ends when all tracks are played once.

– 16 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Back Tapes

To stop during play, press 7.

Playing Back a Tape

To operate the other deck, press TAPE A or TAPE B (or

TAPE A/B on the remote control), then TAPE 3.

1 Press EJECT (0) for the deck you want to

To fast-forward the tape, press ¡ (or ¢ on the remote

control). The tape running indicator (3) starts flashing

quickly.

use.

To rewind the tape, press 1 (or 4 on the remote

control). The tape running indicator (2) starts flashing

quickly.

To remove the cassette, press 0 EJECT for deck A or

EJECT 0 for deck B.

EJECT

For Deck B

For Deck A

EJECT

2 Put a cassette in with the exposed part of the

tape down.

• You can play back only type I.

3 Close the cassette holder gently.

If you put cassettes in both decks A and B, the last deck

which you have put a cassette into is selected.

To operate the other deck, press TAPE A or TAPE B (or

TAPE A/B on the remote control).

The use of the C-120 or thinner tape is not

recommended, since characteristic deterioration

may occur and this tape easily jams in the pinch-

rollers and the capstans.

4 Press TAPE 3 .

The tape play starts and the tape running

indicator (3) starts flashing slowly.

When the tape plays to the end, the deck

automatically stops.

TAPE

– 17 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

Continued

IMPORTANT:

Recording a Tape on Deck B

• It should be noted that it may be unlawful to re-record

pre-recorded tapes, records, or discs without the

consent of the owner of copyright in the sound or video

recording, broadcast or cable programme and in any

literary, dramatic, musical, or artistic embodied

therein.

On the unit ONLY:

1 Press EJECT 0 for the deck B.

• The recording level is automatically set correctly, so it is

not affected by the VOLUME control, the SOUND MODE

control and the SUBWOOFER LEVEL control. Thus,

during recording you can adjust the sound you are actually

listening to without affecting the recording level.

• While recording, you can hear sound modes through the

speakers or headphones. However, the sound is recorded

without these effects (see page 10).

EJECT

• If recordings you have made have excessive noise or static,

the unit may be too close to a TV. Place the unit away from

the TV.

EJECT

• You can use type I tape for recording.

To protect your recording

Cassettes have two small tabs

on the back to protect

unexpected erasure or re-

recording.

2 Put a recordable cassette in with the exposed

part of the tape down.

3 Close the cassette holder gently.

To protect your recording,

remove these tabs.

To re-record on a protected tape, cover the holes with

adhesive tape.

4 Start playing the source — FM, MW, LW,

CD player or auxiliary equipment connected

to AUX IN jacks.

To keep the best recording and playback sound quality

If the heads, capstans, and pinch rollers of the cassette decks

become dirty, the following will occur:

• Impaired sound quality

• When you want to use the dubbing method, see

“Dubbing Tapes” on page 19.

• When the source is CD, you can also use CD Synchro

Recording (see “CD Synchro Recording” on page 19.)

• Discontinuous sound

• Fading

• Incomplete erasure

• Difficulty in recording

REC START CD

/STOP

REC

5 Press REC START/STOP.

The REC (recording) indicator lights up on

the display and recording starts.

To clean the head, capstan, and pinch roller

Use a cotton swab moistened with alcohol.

To stop during recording, press REC START/STOP again

or 7.

Capstan

Erase head

To remove the cassette, press EJECT 0 for deck B.

Pinch roller

Head

To demagnetize the head

Turn off the unit, and use a head demagnetizer (available at

electronics and audio shops).

– 18 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Dubbing Tapes

CD Synchro Recording

You can easily record a CD onto a tape.

• You can also record the tracks in order you have made the

program.

On the unit ONLY:

1 Press TAPE 3, then 7.

On the unit ONLY:

1 Put a recordable cassette into deck B.

2 Place a disc correctly on the circle of the disc

tray, with its label side up.

2 Put the source cassette in deck A, and a

3 Press one of the disc number buttons (CD1,

CD2 or CD3) to select the disc, then 7.

recordable cassette into deck B.

ART DUBBING

3 Press DUBBING.

Dubbing starts.

“DUBBING” appears, and the REC

(recording) indicator lights up on the display.

ART CD

REC START DUBBIN

4 Press CD REC START.

“CD REC” appears, and the REC

(recording) indicator lights up on the display.

To stop during dubbing, press 7.

To remove the cassette, press 0 EJECT for deck A and

EJECT 0 for deck B.

Deck B starts recording and the CD player starts playing.

When the recording is done, the CD player and deck B

stop.

To stop during CD Synchro Recording, press 7.

To remove the cassette, press EJECT 0 for deck B.

– 19 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers

Continued

There are three timers available — Daily Timer, Recording

Timer, and Sleep Timer.

CLOCK

TIMER

2 Press CLOCK/TIMER again.

“ON TIME” appears for 2 seconds, then the

unit enters on-time setting mode.

Before using the timers, you need to set the clock built in the

unit. (See “Setting the Clock” on page 9.)

Using Daily Timer

With Daily Timer, you can wake to your favorite music or

radio program. You can set the timer whether the unit is on or

off.

PRESET

3 Set the on-time you want the unit

to turn on.

How Daily Timer actually works

The unit automatically turns on, set the volume level to the

preset level, and starts playing the specified source when the

1) Press 4 or ¢ to set the hour, then

press SET.

2) Press 4 or ¢ to set the minute,

then press SET.

on-time comes (the

indicator flashes while the timer is

SET

operating). Then, when the off-time comes, the unit

automatically turns off (stands by).

“OFF TIME” appears for 2 seconds, then

the unit enters off-time setting mode.

The timer setting remains in memory until you change it.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

• If you have made a mistake while setting timer, press

CANCEL. (However, this does not always work. If

CANCEL does not work, press CLOCK/TIMER repeatedly

and start from step 1 again.)

4 Set the off-time you want the unit

to turn off (on standby).

1) Press 4 or ¢ to set the hour, then

press SET.

PRESET

2) Press 4 or ¢ to set the minute,

then press SET.

SET

The unit enters source selecting mode.

Before you start...

• When using a CD as the source to play —

– Make sure there is a CD on the currently selected disc

number tray.

• When using a tape as the source to play —

– Make sure that a tape is in the deck whose deck

indicator (A or B) is lit on the display.

• When using the external component as the source to

play —

– Set the timer equipped with the external component at

the same time.

5 Press 4 or ¢ to select the

source to play, then press SET.

• Each time you press 4 or ¢, the

source changes as follows:

PRESET

On the unit ONLY:

CLOCK

1 Press CLOCK/TIMER repeatedly

TIMER

until “DAILY” appears on the

display.

TUNER LW

TUNER MW

TUNER FM

SET

AUX

TAPE

indicator lights up and the DAILY (daily

timer) indicator also starts flashing on the display.

TUNER FM: tunes into a specified preset FM station.

= go to step 6.

TUNER MW: tunes into a specified preset MW station.

= go to step 6.

TUNER LW: tunes into a specified preset LW station.

= go to step 6.

CD:

plays a disc from the first track.

= go to step 7.

• Each time you press the button, the timer setting modes

change as follows:

TAPE:

AUX:

plays a tape in deck A or B. = go to

ON TIME

REC

DAILY

step 7.

plays an external source. = go to step 7.

Canceled

CLOCK

(See page 9.)

ON TIME

– 20 –

Download from Www.Somanuals.com. All Manuals Search And Download.

PRESET

Using Recording Timer

6 Select the preset station number.

Press 4 or ¢ to select the preset

station number, then press SET.

With Recording Timer, you can make a tape of a radio

broadcast automatically. You can set the timer whether the

unit is on or off.

The unit enters volume setting mode.

SET

How Recording Timer actually works

The unit automatically turns on, tunes into the specified

station, sets the volume level to “VOL MIN,” and starts

recording when the on-time comes (the

while the timer is operating). Then, when the off-time comes,

the unit automatically turns off (stands by).

The timer setting remains in memory until you change it.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

indicator flashes

7 Press 4 or ¢ to set the volume

level.

PRESET

• You can select the volume level from

VOL MIN, VOL 1 — VOL 30, and

VOL MAX.

• If you have made a mistake while setting the timer, press

CANCEL. (However, this does not always work. If

CANCEL does not work, press CLOCK/TIMER repeatedly

and start from step 1 again.)

On the unit ONLY:

SET

8 Press SET to complete the Daily

Timer setting.

1 Put a recordable cassette into deck B.

The DAILY (daily timer) indicator stops

flashing and remains lit. The settings you have

done are shown on the display in sequence for your

confirmation.

CLOCK

TIMER

2 Press CLOCK/TIMER repeatedly

until “REC” appears on the

display.

indicator lights up and the REC

(recording timer) indicator also starts flashing on the

display.

STANDBY

Press

STANDBY/ON to

ECO

STANDBY/ON

turn off the unit (on standby)

if you have set the Daily Timer

with the unit turned on.

If the unit is turned on when the timer-on time comes

Daily Timer does not work.

• Each time you press the button, the timer setting modes

change as follows:

To turn on or off Daily Timer after its setting is done

CLOCK

Press CLOCK/TIMER repeatedly until

“DAILY” appears on the display.

ON TIME

REC

TIMER

DAILY

Canceled

CLOCK

(See page 9.)

ON TIME

To turn off the Daily Timer, press

CANCEL.

CANCEL

/DEMO

The DAILY (daily timer) indicator goes off

from the display (“OFF” appears for a while).

The Daily Timer is canceled, but the setting

for the Daily Timer remains in memory.

CLOCK

TIMER

3 Press CLOCK/TIMER again.

“ON TIME” appears for 2 seconds, then the

unit enters on-time setting mode.

SET

To turn on the Daily Timer, press SET.

The DAILY (daily timer) indicator lights up

on the display. The settings you have done are

shown on the display in sequence for your

confirmation.

– 21 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Sleep Timer

4 Set the on-time you want the unit

to turn on.

PRESET

With Sleep Timer, you can fall asleep to music.

You can set Sleep Timer when the unit is turned on.

1) Press 4 or ¢ to set the hour, then

press SET.

2) Press 4 or ¢ to set the minute,

then press SET.

How Sleep Timer actually works

The unit automatically turns off after the specified time

length passes.

SET

“OFF TIME” appears for 2 seconds, then

the unit enters off-time setting mode.

On the remote control ONLY:

5 Set the off-time you want the

unit to turn off (on standby).

1) Press 4 or ¢ to set the hour, then

press SET.

PRESET

SLEEP

1 Press SLEEP.

The time length until the shut-off time appears

and the SLEEP indicator starts flashing on the

display.

2) Press 4 or ¢ to set the minute,

• Each time you press the button, the time length changes

as follows:

then press SET.

The unit enters preset station selecting

mode.

SET

SLEEP10 SLEEP20 SLEEP30 SLEEP60

SLEEP120

SLEEP90

OFF

(Canceled)

2 Wait for about 5 seconds after specifying the

6 Select the preset station.

1) Press 4 or ¢ to select the band

(“TUNER FM”, “TUNER MW” or

“TUNER LW”), then press SET.

PRESET

time length.

The SLEEP indicator stops flashing and remains lit.

To check the remaining time until the shut-off time, press

SLEEP once so that the remaining time until the shut-off time

appears for about 5 seconds.

2) Press 4 or ¢ to select a preset

channel number, then press SET.

The REC (recording timer) indicator stops

flashing and remains lit. The settings you

have done are shown on the display in

sequence for your confirmation.

SET

To change the shut-off time, press SLEEP repeatedly until

the desired time length appears on the display.

To cancel the setting, press SLEEP repeatedly until “OFF”

appears on the display so that the SLEEP indicator goes off

from the display.

STANDBY

7 Press

STANDBY/ON to

turn off the unit (on standby) if

necessary.

ECO

STANDBY/ON

• Sleep Timer is also canceled when you turn off the unit.

Timer Priority

If you want to listen to another source while recording

Press REC START/STOP or 7 to stop recording. Without stopping

it, you cannot change the source.

Since each timer can be set separately, you may wonder what

happens if the setting for these timers overlaps.

Here are examples.

To turn on or off Recording Timer after its setting is

done

• Recording Timer has priority over Daily Timer.

If Daily Timer is set to come on while Recording Timer is

operating, Daily Timer will not come on at all.

CLOCK

Press CLOCK/TIMER repeatedly until

“REC” appears on the display.

TIMER

• If Sleep Timer overlaps with another timer (either Daily

Timer or Recording Timer), a timer with the earlier shut-off

time has priority.

To turn off the Recording Timer, press

CANCEL.

The REC (recording timer) indicator goes off

from the display (“OFF” appears for a while).

The Recording Timer is canceled, but the

CANCEL

/DEMO

7:30

AM 6:00

6:30

7:00

Sleep Timer

setting for the Recording Timer remains in memory.

Recording Timer

canceled.

SET

To turn on the Recording Timer, press SET.

The REC (recording timer) indicator lights up

on the display. The settings you have done are

shown on the display in sequence for your

confirmation.

When using the Recording Timer and Sleep Timer at the

same time, pay special attention to the shut-off time.

– 22 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

To get the best performance of the unit, keep your discs, tapes, and mechanism clean.

Handling cassette tapes

Handling discs

• If the tape is loose in its cassette, take

up the slack by inserting a pencil in

one of the reels and rotating.

• If the tape is loose, it may get

stretched, cut, or caught in the

cassette.

• Remove the disc from its case by

holding it at the edge while pressing the

center hole lightly.

• Do not touch the shiny surface of the

disc, or bend the disc.

• Put the disc back in its case after use to

prevent warping.

• Be careful not to touch the tape

surface.

• Be careful not to scratch the surface of

the disc when placing it back in its

case.

• Avoid exposure to direct sunlight,

temperature extremes, and moisture.

• Avoid the following places to store the

tape:

— In dusty places

To clean the disc

— In direct sunlight or heat

— In moist areas

Wipe the disc with a soft cloth in a

straight line from center to edge.

— Near a magnet

DO NOT use any solvent — such as conventional

record cleaner, spray, thinner, or benzine — to

clean the disc.

– 23 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If you are having a problem with your unit, check this list for a possible solution before calling for service.

If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,

such as your dealer, for service.

Symptom

Cause

Action

Unable to cancel the display demonstration.

Other buttons are pressed to cancel the

display demonstration.

Press DEMO on the unit. (See page 8.)

No sound is heard.

Connections are incorrect or loose.

Check all connections and make

corrections. (See pages 6 to 8.)

Hard to listen to broadcasts because of

noise.

• Antennas are disconnected.

• Reconnect the antennas correctly and

securely.

• The AM (MW/LW) loop antenna is too

close to the unit.

• The FM antenna is not properly extended

• Change the position and direction of the

AM (MW/LW) loop antenna.

• Extend the FM antenna at the best

position.

and positioned.

The disc sound is discontinuous.

The disc is scratched or dirty.

Clean or replace the disc. (See page 23.)

The carrousel does not open or close.

• The AC power cord is not plugged in.

• The carrousel is locked.

• Plug the AC power cord.

• Unlock the carrousel. (See page 16.)

The disc does not play.

The disc is placed upside down.

Place the disc with the label side up.

Turn on the unit.

The cassette holders cannot be opened.

Power supply from the AC power cord has

been cut off while the tape was running.

Impossible to record.

Small tabs on the back of the cassette are

removed.

Cover the holes with adhesive tape.

Operations are disabled.

The built-in microprocessor may

malfunction due to external electrical

interference.

Unplug the AC power cord and then plug it

back in.

Unable to operate the unit from the remote

control.

• The path between the remote control and

the remote sensor on the unit is blocked.

• The batteries are exhausted.

• Remove the obstruction.

• Replace the batteries.

– 24 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Information

Description of the PTY codes:

FINANCE: Stock Market reports, commerce, trading etc.

CHILDREN: Programs targeted at a young audience.

NEWS:

News.

AFFAIRS:

Topical program expanding or enlarging upon the

news — debate, or analysis.

SOCIAL A: Programs about sociology, history, geography,

psychology and society.

INFO:

Program the purpose of which is to impart advice in

the widest sense.

RELIGION: Religious programs.

SPORT:

Program concerned with any aspect of sports.

PHONE IN: Involving members of the public expressing their

views either by phone or at a public forum.

EDUCATE: Educational programs.

DRAMA: All radio plays and serials.

TRAVEL:

LEISURE:

JAZZ:

Travel information.

Programs about recreational activities.

Jazz music.

CULTURE: Programs concerning any aspect of national or

regional culture, including language, theatre, etc.

SCIENCE:

VARIED:

Programs about natural sciences and technology.

COUNTRY: Songs which originate from, or continue the musical

tradition of the American Southern States.

Used for mainly speech-based programs like

quizzes, panel games and personality interviews.

NATIONAL: Current popular music of the nation or region in that

country’s language.

POP M:

Commercial music of current popular appeal.

Rock music.

OLDIES:

FOLK M:

Music from the so-called “golden age” of popular

music.

ROCK M:

M.O.R. M:

Current contemporary music considered to be “easy-

listening.”

Music which has its roots in the musical culture of a

particular nation.

LIGHT M:

Instrumental music, and vocal or choral works.

DOCUMENT:Program concerning factual matters, presented in an

CLASSICS: Performances of major orchestral works,

investigative style.

symphonies, chamber music, etc.

OTHER M: Music not fitting into any of the other categories.

WEATHER: Weather reports and forecasts.

Classification of the PTY codes for some FM stations

may be different from the above list.

– 25 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Amplifier section — CA-MXG51R

Output Power (IEC268-3/DIN)

SUBWOOFERS: 60 W per channel, min. RMS, driven into

6 Ω at 63 Hz with no more than 10% total

harmonic distortion.

MAIN SPEAKERS: 30 W per channel, min. RMS, driven into

6 Ω at 1 kHz with no more than 10% total

harmonic distortion.

Audio input sensitivity/Impedance

(at 1 kHz, measured at MAIN SPEAKERS)

AUX: 400 mV/50 kΩ

Digital output: DIGITAL OUT (OPTICAL)

Signal wave length: 660 nm

Output level:

–21 dBm to –15 dBm

Speakers/Impedance:

6 Ω — 16 Ω

Tuner

FM tuning range:

87.50 MHz — 108.00 MHz

AM tuning range: MW: 522 kHz — 1 629 kHz

LW: 144 kHz — 288 kHz

CD player

CD Capacity:

Dynamic range:

3 CDs

85 dB

Signal-to-noise ratio: 85 dB

Cassette deck

Frequency response

Normal (type I): 50 Hz — 14 000 Hz

Wow and flutter

0.15% (WRMS)

General

Power requirement:

AC 230 V , 50 Hz

Power consumption: 130 W (at operation)

17 W (on standby)

3.5 W (at eco mode)

Dimensions (approx.): 270 mm x 317 mm x 447 mm (W/H/D)

(10¹¹/16 in. x 12¹/2 in. x 17⁵/8 in.)

Mass (approx.):

8.9 kg (19.6 lbs)

Supplied accessories

See page 6.

Design and specifications are subject to change without notice.

– 26 –

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTRUCTIONS

SPEAKER SYSTEM

SP-MXG51R

BEDIENUNGSANLEITUNG: LAUTSPRECHERSYSTEM

MANUEL D’INSTRUCTIONS: SYSTEME DES ENCEINTES

GEBRUIKSAANWIJZING: LUIDSPREKERSYSTEEM

MANUAL DE INSTRUCCIONES: SISTEMA DE ALTAVOCES

ISTRUZIONI: SISTEMA DI ALTOPARLANTI

BRUKSANVISNING: HÖGTALARSYSTEM

KÄYTTÖOHJE: KAIUTINJÄRJESTELMÄ

VEJLEDNING: HØJTTALERSYSTEM

HASZNÁLATI ÚTMUTATÓ: HANGSZÓRÓ RENDSZER

INSTRUKCJA UŻYTKOWANIA: ZESTAW GŁOŚNIKOWY

NÁVOD K OBSLUZE: REPRODUKTOROVÁ SOUSTAVA

Tack för ditt val av dessa JVC-högtalare.

Innan du kopplar in högtalarna i din ljudanläggning bör du för att få

maximala prestanda från högtalarna läsa igenom bruksanvisningen

noggrant. Kontakta din JVC-återförsäljare om du har frågor eller känner

dig osäker.

Thank you for purchasing JVC speakers.

Before you begin using them, please read the instructions carefully to be

sure you get the best possible performance. If you have any questions,

consult your JVC dealer.

Kiitos siitä että päädyit valinnassasi JVC-kaiuttimiin.

Ennen kuin alat käyttää niitä, lue käyttöohje huolellisesti, jotta ne toimisivat

parhaalla mahdollisella tavalla. Jos Sinulla on kysyttävää ota yhteys JVC-

edustajaan.

Vielen Dank für den Kauf dieser JVC-Lautsprecher.

Lesen Sie bitte diese Bedienungsanleitung vor Ingebrauchnahme sorgfältig

durch, um stets optimale Ergebnisse zu erzielen. Wenden Sie sich bei

etwaigen Fragen bitte an Ihren JVC Händler.

Tak for købet af JVC-højttalerne.

Gennemlæs venligst vejledningen omhyggeligt før de tages i brug, så De

kan opnå den bedst mulige ydelse. Forhør hos Deres JVC forhandler hvis

De har nogen spørgsmål.

Nous vous remercions pour l’achat de ces enceintes JVC.

Avant de les utiliser, lire ces instructions avec attention pour en obtenir

les meilleures performances possibles. En cas de questions, consulter

votre revendeur JVC.

Köszönjük, hogy a JVC hangszóró rendszerét választotta. Annak

érdekében, hogy a hangszóró rendszer a legjobb teljesítményt nyújtsa

Önnek, használat előtt kérjük figyelmesen olvassa el ezt a használati

útmutatót. Ha bármilyen kérdése van, forduljon a legközelebbi JVC

márkakereskedőhöz.

Dank u voor de aanschaf van deze JVC luidsprekers.

Lees alvorens over te gaan tot aansluiten, deze gebruiksaanwijzing door

zodat u de best mogelijke prestaties zult verkrijgen. Neem kontakt op met

de JVC dealer indien u vragen heeft.

Dziękujemy za wybranie zestawu głośnikowego firmy JVC.

Le estamos muy agradecidos por haber adquirido estos altavoces de JVC.

Przed rozpoczęciem użytkowania zestawu głośnikowego prosimy o

dokładne zapoznanie się z treścią niniejszej instrukcji użytkowania, aby

uzyskać jak najlepszą pracę głośników. W przypadku jakichkolwiek

zapytań, prosimy o skonsultowanie się z najbliższym dealerm firmy JVC.

Antes de utilizarlos, sirvase leer las instrucciones detenidamente a fin de

obtener el mejor rendimiento posible. Si tienenaluna pregunta, acuda a

su agente de JVC.

Děkujeme Vám, že jste si zakoupili reproduktory JVC.

Grazie per aver acquistato questi altoparlanti della JVC.

Dříve než je začnete používat, přečtěte si prosím pečlivě návod k obsluze,

abyste dosáhli co nejlepší možné funkce. Jestliže máte další otázky, spojte

se s svým prodejcem JVC.

Prima di cominciare l’uso degli altoparlanti, leggete attentamente le

istruzioni per assicurare le migliori prestazioni. Qualora sorgessero dei

dubbi, rivolgetevi al vostro rivenditore JVC.

— SAFETY INSTRUCTIONS —

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet

Switch off using the switch on the equipment and make sure that

your family know how to do this.

international safety standards but, like any electrical equipment, care

must be taken if you are to obtain the best results and safety is to be

assured.

Special arrangements may need to be made for infirm of handi-

capped people.

DON’T use equipment such as personal stereos or radios so that

you are distracted from the requirements of traffic safety. It is illegal

to watch television whilst driving.

Do read the operating instructions before you attempt to use the

equipment.

Do ensure that all electrical connections (including the mains plug,

extension leads and interconnections between pieces of equipment)

are properly made and in accordance with the manufacturer’s

instructions. Switch off and withdraw the mains plug when making or

changing connections.

DON’T listen to headphones at high volume as such use can

permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with

curtains or soft furnishing.

Overheating will cause damage and shorten the life of the equipment.

Do consult your dealer if you are ever in doubt about the installation,

operation or safety of your equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws

— to ensure complete safety always fit the manufacturer’s approved

stand or legs with the fixings provided according to the instructions.

Do be careful with glass panels or doors on equipment.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

– NEVER let anyone, especially children, push anything into holes,

slots or any other opening in the case.

DON’T continue to operate the equipment if you are in any doubt

about it working normally, or if it is damaged in any way — switch

off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous

voltages.

DON’T leave equipment switched on when it is unattended unless it

is specifically stated that it is designed for unattended operation or

has a standby mode.

– this could result in a fatal electrical shock;

–

NEVER guess or take chances with electrical equipment of any kind

– it is better to be safe than sorry!

LVT0693-001A

[B. E. EN. EV]

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection

Anschluß

Ansluiting

Liitäntä

Tilslutning

Csatlakoztatás

Połączenia

Zapojení

CONNECTION

Raccordement

Aansluiting

Conexión

• DO NOT use other amplifier to operate this speaker system

except for CA-MXG51R.

• Turn off power to the whole system before connecting the

Collegamento

speakers to the amplifier.

Left speaker

Linker Lautsprecher

Enceinte de gauche

Linker spreker

Altavoz izquierdo

Altoparlante sinistro

Vänster högtalare

Vasen kaiutin

Venstre højttaler

Bal hangszóró

Lewa kolumna

Levý reproduktor

Right speaker

• The maximum power handling capacity of the CA-MXG51R

main speaker is 40 W Subwoofer is 80 W. Excessive input will

result in abnormal noise and possible damage. In cases where

the signals described below are applied to the speakers, even

if the signals are below the maximum allowable input, they

may cause an overload and burn the wiring of the speakers.

Be sure to lower the amplifier volume beforehand.

Rechter Lautsprecher

Enceinte de droite

Rechter spreker

Altavoz derecho

Altoparlante destro

Höger högtalare

Oikea kaiutin

Højre højttaler

1) Noise during FM tuning.

Jobb hangszóró

Prawa kolumna

Pravý reproduktor

2) High level signals containing high frequency components

produced by a tape deck in the fast forward mode.

3) Click noise produced when turning power of other compo-

nents on and off.

4) Click noise produced when connecting or disconnecting

cords with the power on.

5) Click noise produced when the cartridge is replaced with

the power on.

BLUE

BLAU

BLEU

BLAUW KÉK

AZUL

BLA

SININEN

BLA

BŁĘKITNY

BORŮVKA

6) Click noise produced when operating amplifier switches.

BLU

7) Continuous high frequency oscillation or high pitch electroni-

cally produced musical instrument sound.

8) Howling when using a microphones.

BLACK

SCHWARZ

NOIR

ZWART

NEGRO

NERO

SVART

MUSTA

SORT

FEKETE

CZARNY

ČERNÝ

BLACK

SCHWARZ

NOIR

ZWART

NEGRO

NERO

SVART

MUSTA

SORT

MAIN SPEAKER SUBWOOFER

FEKETE

CZARNY

ČERNÝ

RED

ROT

RED

ROT

ROUGE

ROOD

ROJO

ROSSO

RÖD

ROUGE

ROOD

ROJO

ROSSO

RÖD

PUNAINEN

RØD

PIROS

CZERWONY

ČERVENÝ

Amplifier output terminals

Ausgang des Verstärkers

Bornes de sortie de l’amplificaterur

Uitgangsaansluitengen van de versterker

Terminales de salida de amplificador

Terminali de uscita dell’amplifcator

Utgångar på förstärkaren

SPECIFICATIONS

PUNAINEN

RØD

Type

: 3-way 3-speaker Bass-Reflex

Type

PIROS

Twin Hyper Power-Drive

Subwoofer

Vahvistimen ulostuloliittimet

CZERWONY

ČERVENÝ

Forstærkerudgangsbøsninger

Erősítő kimeneti csatlakozók

Przyłącza wyjścia ze wzmacniacza

Výstupní zdířky zesilovače

Speakers:

Subwoofer

: 13.5 cm (5-3/8 in.) cone × 1

Main woofer

Tweeter

Power Handling Capacity:

Subwoofer

: 13.5 cm (5-3/8 in.) cone × 1

: 5.0 cm (2 in.) cone × 1

: 80 W

: 40 W

Main Speaker

Impedance:

Subwoofer

Main Speaker

: 6 Ω

: 4 Ω

Frequency Range:

Subwoofer

: 26 Hz — 92 Hz

Main Speaker

: 92 Hz — 20 000 Hz

Sound Pressure Level:

Subwoofer

Main Speaker

: 75 dB/W·m

: 88 dB/W·m

Dimensions (W × H × D)

: 275 mm × 317 mm × 309 mm

(10-11/16 in. × 12-1/2 in. × 12-3/16 in.)

Mass

: 5.0 kg (11.0 lbs) each

Design and specifications subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

VICTOR COMPANY OF JAPAN, LIMITED

0201KSMMDWSAM

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Washer IWD 7145 S User Manual
Insignia CRT Television NS R20C User Manual
Jacuzzi Hot Tub J ALLURELuxury Bathing and Entertainment System User Manual
Jasco Computer Keyboard 98136 User Manual
JBL Car Amplifier BPx11001 User Manual
Kenwood Stereo System CT 401 User Manual
Keys Fitness Fitness Equipment STDFR B User Manual
KitchenAid Range 9755235 User Manual
Kodak Digital Camera C1013 User Manual
Korg Musical Instrument GT 120 User Manual