JVC Stereo System 0510WMKMDWJMM User Manual

CAUTION  
CAUTION: Proper Ventilation  
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:  
1. Front: No obstructions and open spacing.  
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.  
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of  
10 cm or more.  
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.  
Basic and Common Operations  
The  
button in any position does not disconnect the  
mains line.  
Basic Operations  
Disconnect the mains plug to shut the power off  
completely (the STANDBY lamp goes off).  
The MAINS plug or an appliance coupler is used as the  
disconnect device, the disconnect device shall remain  
readily operable.  
When the system is on standby, the STANDBY lamp lights  
red (except when the power is supplied using batteries.)  
When the system is turned on, the STANDBY lamp goes  
off.  
NOTE  
Press  
DO NOT turn off (standby) the System with the volume set to an extremely high  
level; otherwise, the sudden blast of sound can damage your hearing, speakers  
and/or headphones when you turn on the System or start playback.  
To  
On the  
System  
On the  
remote  
Point at the remote sensor on the front panel.  
(The operating range is approx. 7 m.)  
COMPACT COMPONENT SYSTEM  
Side  
Front  
Turn on or off  
(standby) the  
power  
The STANDBY lamp on the System  
turns off/on.  
15 cm  
15 cm  
MX-KC68  
How to cancel the  
demonstration  
Press and hold CANCEL/  
DEMO button while  
on standby. (Refer to  
the attached sheet  
15 cm  
1 cm  
1 cm  
15 cm  
1 cm  
Consists of CA-MXKC68, SP-MXKC68F  
and SP-MXKC68W  
The power can be remote controlled. However, when the  
power is supplied using batteries, the system cannot be  
turned on by remote control.  
See “Playing Back a Discon page 4.  
15 cm  
MX-KC38  
“Information about the  
demonstration function.)  
CAUTION  
Consists of CA-MXKC38, SP-MXKC38  
10 cm  
To reduce the risk of electrical shocks, fire, etc.:  
1. Do not remove screws, covers or cabinet.  
2. Do not expose this appliance to rain or moisture.  
See “Listening to iPodon page 6.  
Select a  
source  
CA-MXKC68  
CA-MXKC38  
SP-MXKC68F CA-MXKC68 SP-MXKC68F SP-MXKC68W  
SP-MXKC38 CA-MXKC38 SP-MXKC38  
STANDBY lamp  
Press repeatedly to selectFM,”“AM,or  
“AUDIO IN.  
For “FMand “AM,see “Listening to  
FM and AM Broadcastson page 5.  
For “AUDIO IN,see “Listening to  
Digital Audio Playeron page 6.  
CAUTION:  
Thank you for purchasing a JVC product.  
Do not block the ventilation openings or holes. (If  
the ventilation openings or holes are blocked by a  
newspaper or cloth, etc., the heat may not be able to get  
out.)  
Subwoofer is only available  
for MX-KC68.  
INSTRUCTIONS  
Mains (AC) Line Instruction (not applicable for Australia)  
GVT0243-016B [A/UJ/UW/US]  
0510WMKMDWJMM  
Do not place any naked flame sources, such as lighted  
candles, on the apparatus.  
PHONES jack  
You can adjust the volume level from  
level 0 (“VOLUME MIN”) to level 31  
(“VOLUME MAX”).  
Main unit (rear)  
Adjust the  
volume  
When discarding batteries, environmental problems  
must be considered and local rules or laws governing the  
disposal of these batteries must be followed strictly.  
Do not expose this apparatus to rain, moisture, dripping  
or splashing and that no objects filled with liquids, such  
as vases, shall be placed on the apparatus.  
©2008 Victor Company of Japan, Limited  
Using Headphones  
Be sure to turn down the volume  
Drop the  
volume in a  
moment  
before connecting or putting on the  
To restore the volume, press again, or  
adjust the volume level.  
Stereo mini plug  
headphones.  
Warnings, Cautions and Others  
IMPORTANT FOR LASER PRODUCTS  
1. CLASS 1 LASER PRODUCT  
2. CAUTION: Do not open the top cover or cabinet. There  
are no user serviceable parts inside the unit; leave all  
servicing to qualified service personnel.  
3. CAUTION: Visible and/or invisible class 1M laser  
radiation when open. Do not view directly with optical  
instruments.  
Connecting the headphones will  
deactivate the speakers.  
Sound adjustments also affect the sound  
through the headphones.  
CAUTION:  
Display Settings  
Excessive sound pressure from earphones or headphones  
can cause hearing loss.  
Press  
CAUTION for mains (AC) line  
To  
On the  
System  
On the  
remote  
BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch  
provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk  
of fire/electric shock.  
Sound Adjustment  
Display Information  
Press when the System is on standby.  
Setting the Save mode allows you  
to reduce power consumption by  
turning the display off while on  
standby.  
Press  
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED  
INSIDE THE UNIT.  
Set the Save  
mode  
Main display  
To  
On the  
System  
On the  
remote  
[European Union only]  
File type indicators  
(See page 4.)  
Play mode indicators  
(See page 4.)  
FM reception indicators  
(See page 5.)  
Sound Turbo indicator lights up.  
To cancel this function, press again.  
Reinforce the  
heavy sound  
NOTE  
To cancel this function, press again.  
Press repeatedly to select a brightness  
level.  
The remote control illustrations of MX-KC68 are used in this instruction manual.  
Press repeatedly to select a sound  
mode you want.  
Changing the  
display  
DIMMER 1  
DIMMER 2  
Select a  
sound mode  
brightness  
DIMMER OFF  
(Off)  
Changing the  
display  
information  
(Clock and  
source)  
Press repeatedly to select a subwoofer  
level.  
Press briefly.  
Change the  
subwoofer  
level (only for  
MX-KC68)  
For setting the clock, seeSetting the  
Clock and Using Timerson page 7.  
: SUBWOOFER1  
Timer mode indicators  
(See page 7.)  
Sound Turbo indicator (See the left table.)  
Subwoofer level indicator (See the left table.)  
Sound mode indicator (See the left table.)  
: SUBWOOFER2  
: SUBWOOFER3  
A.STBY (Auto Standby)  
indicator (See page 4.)  
1
3
Precautions  
Playing Back a Disc  
Notes on the power cord  
This System can play back...  
– CD.  
To Select a Group (for MP3/WMA only)  
Connections  
Playing at Random—Random Play  
When you are away on travel or otherwise for an extended period of time, remove the plug  
from the wall outlet. A small amount of power (1.00 W or less) is always consumed while the  
power cord is connected to the wall outlet.  
When unplugging the System from the wall outlet, always pull the plug, not the power cord.  
Do not handle the power cord with wet hands.  
Disconnect the power cord before cleaning the System or moving the System.  
Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire,  
electric shock, or other accidents.  
If the cord is damaged, consult a dealer and have the power cord replaced with a new one.  
Avoid moisture, water, dust, and high temperatures  
Do not place the System in moist or dusty places.  
Press before you start playback.  
The RND (random) indicator lights on the display.  
Do not connect the AC power cord until all other connections have been made.  
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files  
in ISO 9660 format.  
When playing back an MP3 or WMA track, MP3 or WMA indicator lights on the  
display.  
1
1
2
Press briefly.  
Playback starts in random order.  
To connect the FM antenna (supplied)  
Extend it so that you can obtain the best reception.  
To assemble the AM loop antenna (supplied)  
2
Random Play ends when all tracks are played back.  
Select a group number.  
FM antenna  
(supplied)  
Loading a Disc  
On the System only  
1
To Operate on the Random Play Mode  
To  
Press  
Press to open the disc tray.  
4 goes back to the beginning of the  
3
Skip a track  
current track.  
Select a track number.  
You can use also 4 or ¢ buttons.  
If water gets inside the System, turn off the power and remove the plug from the wall outlet,  
then consult your dealer. Using the System in this state may cause a fire or electrical shock.  
Do not expose the System to direct sunlight or place it near a heating device.  
For better FM reception  
Exit from  
random play  
2
Press once while playback is stopped.  
To connect the AM loop antenna  
Outdoor FM antenna  
(not supplied)  
When using an 8 cm disc, place it on the  
Notes on installation  
inner circle of the disc tray.  
RESUME Play (for MP3/WMA only)  
Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.  
Do not install the System in a place subject to vibrations.  
Do not put heavy objects on the System.  
Playing Repeatedly—Repeat Play  
AM loop antenna (supplied)  
Turn it until the best  
reception is obtained.  
When you stop the playback by one of the following operations, this System  
stores the beginning of the stopped track on the disc.  
– Pressing 7 once  
Press repeatedly to specify the repeat mode as follows:  
1
2
REP 1  
Repeats the current (or specified) track.  
Repeats all tracks in the current group (MP3/  
WMA only).  
Disconnect the supplied FM antenna, and connect to an  
outdoor FM antenna using a 75 Ω wire with coaxial type  
connector.  
3
Press to close the disc tray.  
To prevent malfunction or damage of the System  
Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.  
Do not block the vents.  
– Changing the source  
REP  
When you start playback again, playback starts from the stored position.  
REP ALL Repeats all tracks.  
(Off) Normal playback  
Basic Disc Operations  
To clear the stored position, turn off the System.  
Opening the disc tray also clears the stored position.  
There are no user-serviceable parts inside.  
Press  
If anything goes wrong, unplug the power cord and consult your dealer.  
NOTE  
To  
On the  
System  
On the  
remote  
NOTE  
Make sure the antenna conductors do not  
touch any other terminals, connecting cords  
and power cord. Also, keep the antennas  
away from metallic parts of the System,  
connecting cords, and the AC power cord.  
This could cause poor reception.  
This function does not work in program play and random play.  
Current track number and elapsed  
playing time appear on the main  
display.  
For MP3/WMA files: Before current  
track number and elapsed playing  
time appear, the tag information is  
scrolled if it is recorded.  
Main speaker  
Main speaker  
Subwoofer  
(Only for MX-KC68)  
Turning off the System Automatically  
—AUTO STANDBY function  
Press until the A.STBY indicator lights  
on the display.  
Getting Started  
Supplied Accessories  
After unpacking, check to be sure that you have all the following items. The number in  
parentheses indicates the quantity of each piece supplied.  
Programming the Playing Order—Program Play  
Press before you start playback.  
The PROG (program) indicator lights on the display.  
1
2
Play back  
the disc  
The A.STBY indicator starts flashing  
on the display after playback stops.  
If no operation is done for about 3  
minutes, the System turns off.  
To a wall outlet  
Remote control (x 1)  
AM loop antenna (x 1)  
Batteries (x 2)  
For MP3/WMA files: select a group number, then a  
Plug the AC power cord only after  
all connections are complete.  
If the wall outlet does not match  
the AC plug, use the supplied AC  
plug adapter (not applicable for  
Australia).  
During playback, press again to  
pause.  
While playback is stopped, total track  
number and total playing time (for  
MP3/WMA files, group number and  
track number) appear on the main  
display.  
track number.  
FM antenna (x 1)  
For CD: select a track number.  
AC plug adapter (x 1) (not supplied for Australia)  
The AUTO STANDBY function also works in the  
following cases:  
– “IPODis selected as the source and no iPod is  
connected to the System.  
– “AUDIO INis selected as the source and no  
equipment is connected to the AUDIO IN  
terminal.  
If anything is missing, consult your dealer immediately.  
Repeat step 2 to program other tracks you want.  
If you try to program a 51st track, “FULLwill appear on the main display.  
Stop  
playback  
3
4
Prepare the Remote Control  
Insert the battery into the remote control by matching the polarity (+ and –) correctly.  
The tracks are played back in the programmed order.  
If the range or effectiveness of the remote control decreases, replace both batteries.  
Press to select the next tracks.  
To connect the speaker cords  
Select a  
track  
To Operate on the Program Play Mode  
Make sure all speakers are connected correctly and firmly.  
R6P(SUM-3)/AA(15F)  
The AUTO STANDBY function does not work  
whenFMorAMis selected as the source.  
MX-KC68  
MX-KC38  
Press to go back to the beginning of  
the current or previous tracks.  
To  
Press  
When connecting the speaker cords, match the polarity  
of the speaker terminals:  
Check the  
programmed  
contents  
or  
To cancel this function, press again.  
Main speakers: blue cord to (+) and black cord to (–)  
Press while playback is stopped.  
Select a  
track  
To select number 5, press 5.  
To select number 25, press 10, 2,  
then 5.  
Subwoofer: red cord to (+) and black cord to (–)  
Prohibiting Disc Ejection  
You can lock the disc tray so that no one can eject  
the loaded disc.  
This is possible while the System is on standby  
and the disc tray is closed.  
NOTES  
number  
Add tracks  
Repeat step 2 above while playback is stopped.  
DO NOT connect more than one speaker to each  
Press while playback is stopped.  
terminal.  
Press and hold to fast-forward the track  
during playback.  
Press and hold to fast-reverse the track  
during playback.  
Forward  
search/  
Reverse  
search  
DO NOT allow the conductor of the speaker cords to be  
Erase the last  
track  
The track number and the program  
number of the new last track appear on  
the main display.  
CAUTION:  
in touch with  
the metallic  
parts of the  
System.  
On the System only  
Press and hold  
Danger of explosion if battery is incorrectly replaced. Replace only with the same or  
equivalent type.  
To the  
subwoofer  
To the right  
speaker  
To the left  
speaker  
To the right  
speaker  
To the left  
speaker  
Erase the entire  
program  
Exit from  
program play  
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.  
Press and hold for 2 seconds.  
NOTE  
If no disc is inserted, “NO DISCappears on the main display.  
Press while playback is stopped.  
To cancel the prohibition, repeat the same procedure.  
2
4
Download from Www.Somanuals.com. All Manuals Search And Download.  

Intel Computer Hardware V09 User Manual
Kambrook Iron KSS70 User Manual
Karcher Vacuum Cleaner NT 361 User Manual
Kenwood Stereo Receiver VR 8070 User Manual
Keurig Coffeemaker SS 300C User Manual
KitchenAid Pasta Maker KPCA User Manual
KitchenAid Ventilation Hood KICU465SBL0 User Manual
Korg Musical Instrument Pa800 User Manual
Kramer Electronics Home Theater Server RC 81R User Manual
Kramer Electronics Yard Vacuum TBUS 201 User Manual