COMPACT COMPONENT SYSTEM
CA-MXKA6
STANDBY/ON
SLEEP
AUX
FM MODE
FM /AM
CD
CD1
CD2
CD3
REPEAT PROGRAM/RANDOM
TAPE
A/B
TAPE
SELECT
RDS MODE DISPLAY MODE
VOLUME
SOUND
MODE
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
RM-SMXKA6R REMOTE CONTROL
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1014-003A
[B]
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment,
care must be taken if you are to obtain the best results and safety is to be assured.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of
equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug
when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch
off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended opera-
tion or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is
illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s
approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case - this could
result in a fatal electrical shock.;
— NEVER guess or take chances with electrical equipment of any kind.
it is better to be safe than sorry!
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing the JVC Compact Component System.
We hope it will be a valued addition to your home, giving you years of enjoyment.
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have a query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
❏ The controls and operations have been redesigned to make them very easy to use, freeing you to just enjoy the
music.
• With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, Cassette Deck, or
CD Player with a single touch.
❏ The great SEA (Sound Effect Amplifier) effects Rock, Pop and Classics are provided.
❏ The Active Bass EX. (Extension) circuitry faithfully reproduces low frequency sounds.
❏ The Sound Turbo function provides emphasized rich sound.
❏ A 45-station preset capability (30 FM and 15 AM (MW)) in addition to auto-seek and manual tuning.
❏ CD changer function can operate 3 discs.
• Discs can be changed during play using the Carrousel tray (rotational tray).
• Continuous, random or program play of 3 discs.
❏ Two Decks enabling tape dubbing.
❏ Timer functions; Daily Timer, REC (Recording) Timer, and Sleep Timer.
❏ You can connect various external units, such as an MD recorder.
❏ The CD Player can play back a CD-R and CD-RW.
How This Manual Is Organized
• Basic information that is the same for many different functions - e.g. setting the volume - is given in the section “Basic Operations”,
and not repeated under each function.
• The names of buttons/controls and display messages are written in all capital letters: e.g. FM/AM, “NO DISC”.
• If the button names on the Unit and the Remote Control are the same, the description on where the button is used will be omitted.
• System functions are written with an initial capital letter only: e.g. Normal Play.
Use the table of contents to look up specific information you require.
We have enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.
IMPORTANT CAUTIONS
Installation of the System
• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)
• Leave sufficient distance between the System and a TV.
1
• Do not use the System in a place subject to vibrations.
Power cord
• Do not handle the power cord with wet hands!
2
• Some power is always consumed as long as the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
Malfunctions, etc.
3
• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the System.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction ...................................................................................................................1
Features.................................................................................................................................................... 1
How This Manual Is Organized............................................................................................................... 1
IMPORTANT CAUTIONS..................................................................................................................... 1
Table of Contents..........................................................................................................2
Getting Started ..............................................................................................................3
Accessories .............................................................................................................................................. 3
How To Put Batteries In the Remote Control.......................................................................................... 3
Using the Remote Control....................................................................................................................... 3
Connecting the FM Antenna.................................................................................................................... 4
Connecting the AM (MW) Antenna........................................................................................................ 5
Connecting the Speakers ......................................................................................................................... 5
Connecting External Equipment.............................................................................................................. 6
Connecting to the Wall Outlet................................................................................................................. 6
DEMO Mode ........................................................................................................................................... 6
COMPU Play........................................................................................................................................... 6
Basic Operations...........................................................................................................7
Turning the Power On and Off................................................................................................................ 7
ECO Mode (ECO) ................................................................................................................................... 7
Adjusting the Volume.............................................................................................................................. 8
Fade-out Muting (FADE MUTING)....................................................................................................... 8
Reinforcing the Bass Sound (ACTIVE BASS EX.)................................................................................ 8
Emphasizing the Sound (SOUND TURBO) ........................................................................................... 8
Selecting the Sound Mode (SOUND MODE)......................................................................................... 8
Entering the Number with the Remote Control (Numeric Keys)............................................................ 8
Using the Tuner.............................................................................................................9
Tuning In a Station .................................................................................................................................. 9
Presetting Stations ................................................................................................................................. 10
To Change the FM Reception Mode ..................................................................................................... 10
Receiving FM Stations with RDS ......................................................................................................... 11
Using the CD Player....................................................................................................14
To Load CDs ......................................................................................................................................... 15
To Unload CDs...................................................................................................................................... 15
Basics of Using the CD Player-Normal Play......................................................................................... 16
Programming the Playing Order of the Tracks...................................................................................... 17
Random Play.......................................................................................................................................... 18
Repeating Tracks ................................................................................................................................... 18
Tray Lock Function ............................................................................................................................... 18
Using the Cassette Deck (Listening to a Tape) ........................................................19
Playing a Tape ....................................................................................................................................... 19
Using the Cassette Deck (Recording) ......................................................................20
Standard Recording ............................................................................................................................... 21
CD Synchro Recording.......................................................................................................................... 21
Tape to Tape Recording (DUBBING)................................................................................................... 21
Using an External Equipment ....................................................................................22
Listening to the External Equipment..................................................................................................... 22
Using the Timers .........................................................................................................23
Setting the Clock ................................................................................................................................... 23
Setting the Daily Timer ......................................................................................................................... 24
Setting the REC (Recording) Timer ...................................................................................................... 25
Setting the SLEEP Timer ...................................................................................................................... 27
Timer Priority ........................................................................................................................................ 27
Care And Maintenance................................................................................................28
Troubleshooting..........................................................................................................29
Specifications...............................................................................................Back cover
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Accessories
Make sure that you have all of the following items, which are supplied with the System.
AM (MW) Loop Antenna (1)
FM Wire Antenna (1)
Remote Control (1)
Batteries (2)
If any of these items are missing, contact your dealer immediately.
How To Put Batteries In the Remote Control
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
R6P(SUM-3)/AA(15F)
CAUTION:
• Handle batteries properly.
❏ To avoid battery leakage or explosion:
• Remove batteries when the Remote Control will not be used for a long time.
• When you need to replace the batteries, replace both batteries at the same time with new ones.
• Do not use an old battery with a new one.
• Do not use different types of batteries together.
Using the Remote Control
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m (23 feet) away.
You need to point the Remote Control at the remote sensor on the System’s front panel.
Remote sensor
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
CAUTION:
• Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Using the Supplied Wire Antenna
FM wire antenna (supplied)
Using the Coaxial Type Connector (Not supplied)
A 75-ohm antenna with coaxial type connector (IEC or DIN45 325) should be connected to the FM 75-ohm COAXIAL terminal.
If reception is poor, connect the outdoor antenna.
FM outdoor antenna
(Not supplied)
Coaxial cable
• Before attaching a 75 ohm coaxial lead (the kind with a round wire going to an outdoor antenna), disconnect the supplied
FM Wire Antenna.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the AM (MW) Antenna
Rear Panel of the Unit
AM (MW) antenna wire (not supplied)
If reception is poor, connect the outside antenna.
Turn the loop until you have
the best reception.
AM (MW) loop antenna (Supplied)
Attach the AM (MW) loop
to its base by snapping
the tabs on the loop into
the slot in the base.
• Even when connecting an outside AM (MW) antenna, keep the indoor AM (MW) loop connected.
CAUTION:
• To avoid noise, keep antennas away from the System, the connecting cord and the AC power cord.
Connecting the Speakers
Connect the right speaker to the RIGHT speaker terminals and the left speaker to the LEFT speaker terminals. “Right” / “Left” is labeled
on the rear of the speaker.
1. Open each of the terminals to connect the speaker wire leads.
2. Connect the speaker cords to the Speaker terminals of the Unit.
Connect the red (+) and black (–) cords of the right side speaker to the red (+) and black (–) terminals marked RIGHT on the System.
Connect the red (+) and black (–) cords of the left side speaker to the red (+) and black (–) terminals marked LEFT on the System.
3. Close each of the terminals.
Right side (rear view)
Left side (rear view)
Red
Red
Black
Black
CAUTIONS:
• A TV may display irregular colors if located near the speakers. If this happens, set the speakers away
from the TV.
• Use speakers with the correct impedance only. The correct impedance is indicated on the rear panel.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting External Equipment
Connect a signal cord (not supplied) between the System’s AUX-IN terminals and the output terminals of the external MD recorder, tape
deck, etc.
You can then listen to the external source through the System.
Signal cord (not supplied)
MD recorder, tape deck, etc. (not supplied)
Pin-plug x 2
Pin-plug x 2
Connecting to the Wall Outlet
Plug the AC power cord into the wall outlet.
Now, your System is at your command!
DEMO Mode
When the System is connected to the wall outlet, a DEMO mode displaying some of the system’s features automatically starts.
To turn the DEMO display off, press any of the operation buttons. The DEMO display automatically stops.
To turn the DEMO display on, press the DEMO button on the Unit for more than 2 seconds.
CANCEL
(For 2 seconds)
DEMO
• While the System is turned on, the DEMO display will automatically starts if no operation is made for 2 minutes. To cancel
this auto DEMO display function, press the CANCEL button on the Unit during DEMO display.
COMPU Play
JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch.
With One Touch Operation you can play a CD, a tape, turn on the radio, or listen to an external equipment with a single press of the play
button for that function. One Touch Operation turns the power on for you, then starts the function you have specified. If the System is not
ready (no CD or tape in place), the System still powers on so you can insert a CD or tape.
How One Touch Operation works in each case is explained in the section dealing with that function.
The COMPU PLAY buttons are:
On the Unit
CD 6button
FM/AM button
TAPE 3button
AUX button
CD1, CD2 and CD 3 buttons
CD Open/Close 0button
On the Remote Control
CD 6button
FM/AM button
TAPE 3button
AUX button
CD1, CD2 and CD 3 buttons
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
)
STANDBY/ON
STANDBY/ON
SLEEP
Display
Numeric
keys
AUX
FM MODE
FM /AM
SOUND MODE
SOUND TURBO
ACTIVE BASS EX.
VOLUME
PHONES
STANDBY indicator
CD
CD1
CD2
CD3
REPEAT PROGRAM/RANDOM
TAPE
A/B
TAPE
SELECT
RDS MODE DISPLAY MODE
VOLUME
ECO
SOUND
MODE
SOUND
MODE
ACTIVE
BASS EX.
FADE
ACTIVE
SOUND
VOLUME +,–
MUTING
BASS EX. TURBO
FADE MUTING
RM-SMXKA6R REMOTE CONTROL
SOUND
TURBO
Various information
BASS indicator
SOUND TURBO
indicator
Sound Mode indicator
Level bar
Status bar (Indicates various statuses.)
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
Turning the Power On and Off
ECO Mode (ECO)
The System has three energy modes; power on, power off (Stand-
by) and ECO. In ECO mode, the display goes off and the least
power is consumed.
To enter ECO mode, press the ECO button on the Unit in Stand-
by mode (while the STANDBY indicator lights up). “ECO
MODE” appears on the display, then the display goes off. The
STANDBY indicator remains lit.
Turning the System On
Press the
button.
1
STANDBY/ON
STANDBY
or
To cancel ECO mode and turn on the power, press the
button on the Unit for a second.
To cancel ECO mode and enter Standby mode, press the
ECO button again for a second.
The display comes on and “WELCOME” is displayed once.
The STANDBY indicator goes out.
The System comes on ready to continue in the mode it was in
when the power was last turned off.
• For example, if the last thing you were doing was listening
to a CD, you are now ready to listen to a CD again. If you
wish, you can change to another source.
• If you were listening to the Tuner last, the Tuner comes on
playing the station it was last set to.
Turning the System Off
Press the
button again.
1
STANDBY/ON
STANDBY
or
“GOOD BYE” is displayed and the display goes out, except
for the clock display. The STANDBY indicator lights up. (The
display is dimmed.)
• Some power is always consumed even though power is
turned off (called Standby mode).
• To switch off the System completely, unplug the AC power
cord from the wall outlet. When you unplug the AC power
cord, the clock will be reset to 0:00 immediately.
%
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Adjusting the Volume
Selecting the Sound Mode
(SOUND MODE)
Turn the VOLUME control on the Unit clockwise to increase the
volume or turn it counterclockwise to decrease the volume.
Press the VOLUME + button on the Remote Control to increase
the volume or press the VOLUME – button on the Remote Control
to decrease the volume.
You can select one of 3 SEA (Sound Effect Amplifier) modes.
You can use this effect only for playback.
On the Unit
To get the effect, press one of the Sound Mode buttons, ROCK,
POP, or CLASSIC.
You can set the volume level to MIN, 1-31, or MAX.
The selected Sound Mode name “ROCK”, “POP”, or “CLASSIC”
appears on the display. The “SOUND MODE” indicator also lights
up on the display.
To cancel the effect, press the currently selected mode button
again.
When the effect is canceled, the “SOUND MODE” indicator stays
lit.
For example, if the current Sound Mode is ROCK, press the
ROCK button again. “OFF” appears on the display, showing that
no sound effect is applied.
CAUTION:
• DO NOT turn on the System and/or start playing
any source without first setting the VOLUME
control to minimum, as a sudden blast of sound
could damage your hearing, speakers and/or
headphones.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
ROCK
Boosts low and high frequencies. Good for
acoustic music.
POP
CLASSIC
Good for vocal music.
Set for wide and dynamic sound stereo
systems.
OFF
No sound effect applies.
Fade-out Muting (FADE MUTING)
On the Remote Control
Press the SOUND MODE button until Sound Mode you want ap-
pears on the display.
You can mute the output with one touch operation.
The “SOUND MODE” indicator lights up in the display.
Each time you press the button, the Sound Mode changes as fol-
lows:
To muting the output, press the FADE MUTING button on the
Remote Control. The output is faded out.
To release muting, press the FADE MUTING button once
again. The output is faded in to the previous level.
ROCK =POP =CLASSIC =OFF =(back to the beginning)
• After Fade-out Muting, turning the VOLUME control on the
unit or pressing the VOLUME button on the Remote Control
will increase the volume from MIN. setting.
To cancel the effect, press the SOUND MODE button until
“OFF” appears on the display.
The Sound Mode indicator stays lit.
Reinforcing the Bass Sound
(ACTIVE BASS EX.)
Entering the Number with the
Remote Control (Numeric Keys)
The richness and fullness of the bass sound is maintained regard-
less of how low you set the volume.
You can use this effect only for playback.
You will use the number keys on the Remote Control to enter num-
bers for presetting stations, recalling the preset stations, or pro-
gramming the playing tracks on CDs.
How to enter the number with the number keys is explained here.
To get the effect, press the ACTIVE BASS EX. (Extension)
button.
Examples:
The “BASS” indicator lights up and “ACTIVE BASS EXTEN-
SION” appears on the display.
To cancel the effect, press the button again.
The “BASS” indicator goes out and “OFF” appears on the display.
• To enter number 5, press 5.
• To enter number 15, press +10, then 5.
• To enter number 20, press +10, then 10.
• To enter number 25, press +10, +10, then 5.
Emphasizing the Sound
(SOUND TURBO)
High and low frequencies are highly boosted.
To get the effect, press the SOUND TURBO button.
The SOUND TURBO indicator lights up and “SOUND TURBO
ON” appears on the display.
To cancel the effect, press the button again.
The SOUND TURBO indicator goes out and “OFF” appears on
the display.
• Selecting the Sound Turbo function turns the Active Bass EX.
and Sound Mode to off. While the Sound Turbo will be turned
off, if either Active Bass EX. or Sound Mode function is
selected.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
STANDBY/ON
Numeric
SLEEP
keys
AUX
FM MODE
FM /AM
¡
¢
FM/AM
FM MODE
SET
CD
SELECT +,–
CD1
CD2
CD3
REPEAT PROGRAM/RANDOM
RDS MODE
TAPE
A/B
TAPE
DISPLAY MODE
SELECT
RDS MODE DISPLAY MODE
VOLUME
FM/AM
4
DISPLAY MODE
RDS MODE
SOUND
MODE
22
SELECT +,–
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
RM-SMXKA6R REMOTE CONTROL
Band display, Frequency display, Preset channel
RDS indicator
FM mode indicators
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
You can listen to FM and AM (MW) stations. Stations can be
tuned in manually, automatically, or from preset memory storage.
• Manual Tuning (Using the Unit only)
Briefly press the 22 or ¡ button on the Unit to move
from frequency to frequency until you find the station you
want.
❏ Before listening to the radio:
• Make sure that both the FM and AM (MW) antennas are cor-
rectly connected. (See pages 4 and 5).
OR
• Auto Tuning (Using the Unit only)
If you hold down the 22or ¡button on the Unit for 1
second or more and then release it, the frequency changes
down, or up, automatically until a station is found.
OR
• Preset Tuning (Possible only after presetting sta-
tions)
Preset tuning using the Unit:
One Touch Radio
Just press the FM/AM button to turn on the System and start play-
ing the station you were last tuned to.
❏ You can switch from any other sound source to the radio by
pressing the FM/AM button.
Select the preset number you want, using the 4 or ¢
button.
Tuning In a Station
Example:
Press the FM/AM button.
1
The Band and Frequency you were last tuned to appear on the
display.
Press the ¢ button until the preset number “P12” appears
on the display. Then, the display will show the preset
number’s band and frequency.
(If the last station was selected using the preset number, the
preset number appears first.)
Each time you press the button, the band alternates between
FM and AM (MW).
or
FM /AM
PRESET
FM / AM
or
Preset tuning using the Remote Control:
Enter the preset number you want to recall using the numer-
ic keys. See “Entering the Number with the Remote Con-
trol” on page 8.
(on the Unit) (on the Remote Control)
Select a station using one of the following
2
methods.
Example:
Press +10, then 2 to recall the preset number 12. Then, the
display will show the preset number’s band and frequency.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
CAUTION:
• Even if the System is unplugged or if the power
failure occurs, the preset stations will be stored
for a few days. However, in case the preset sta-
tions are erased, you will need to preset the sta-
tions again.
• In AM (MW) broadcast, reception sensitivity will be chang-
ed by turning the AM (MW) loop antenna. Turn the AM
(MW) loop antenna for best reception.
Presetting Stations
To Change the FM Reception
Mode
You can preset up to 30 FM stations and up to 15 AM (MW) sta-
tions.
When you are tuned in to an FM stereo broadcast, the “ST (Ster-
eo)” indicator lights up and you can hear stereo effects.
If an FM stereo broadcast is hard to receive or noisy, you can select
• Preset numbers may have been set to factory test fre-
quencies prior to shipment. This is not a malfunction. You
can preset the stations you want into memory by following
one of the presetting methods below.
• During presetting stations, if no button operation is made
for 5 seconds, the display returns to the band/frequency
display. In this case, repeat steps from the beginning.
Monaural mode. Reception improves, but you lose stereo effect.
Press the FM MODE button on the Remote Control so
that the “MONO” indicator lights up on the display.
FM MODE
ST
MONO
To restore the stereo effect, press the FM MODE button on
the Remote Control so that the “MONO” indicator goes off.
Selecting other station will also cancel the FM Mono mode and re-
store the stereo effect.
TUNING
SET
SET
FM / AM
or
FM=30, AM=15
When changing the Band
Using the Unit
Select a band by pressing the FM/AM button.
1
2
Press the
station.
or
22 ¡
button to tune in a
Press the SET button.
3
4
“SET” will blink for 5 seconds.
Press the 4 or ¢button to select the
preset number.
¢: Increases the preset number by 1.
4: Decreases the preset number by 1.
Press the SET button.
5
6
“STORED” appears and, after 2 seconds, the display returns to
the band/frequency display.
Repeat above steps 2 to 5 for each station
you want to store in memory with a preset
number.
To change the preset stations, repeat the same steps as
above.
• In step 4, you can select the preset number using the nu-
meric keys on the Remote Control. See “Entering the
Number with the Remote Control” on page 8.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
To search for a program by PTY codes
One of the advantages of the RDS service is that you can locate a
particular kind of program by specifying the PTY codes.
Receiving FM Stations with
RDS
To search for a program using PTY codes:
You can use the RDS (Radio Data System) by using the buttons on
the Unit or the Remote Control.
On the Unit
RDS allows FM stations to send additional signals with their reg-
ular program signals. For example, the stations send their station
names, and information about what type of program they broad-
cast, such as sports or music, etc. This Unit can receive the follow-
ing types of RDS signals:
On the Remote Control
PS (Program Service):
shows commonly known station names.
PTY (Program Type):
shows types of broadcast program.
RT (Radio Text):
shows text messages the station sends.
What information can RDS signals provide?
The display shows RDS signal information that the station sends.
Press the RDS MODE button once while lis-
tening to an FM station.
“P. SELECT” appears on the display.
1
Select the PTY code using the SELECT + or –
button within approx. 10 seconds.
Each time you press the button, the display shows a category
in the following order:
2
To show the RDS signals on the display
Press the DISPLAY MODE button while listening to an
FM station.
Each time you press the button, the display changes to show infor-
mation in the following order:
NEWS ↔ AFFAIRS ↔ INFO ↔ SPORT ↔ EDUCATE
↔ DRAMA ↔ CULTURE ↔ SCIENCE ↔ VARIED ↔
POP M ↔ ROCK M ↔ MO.RM ↔ LIGHT M ↔ CLAS-
SICS ↔ OTHER M ↔ WEATHER ↔ FINANCE ↔
CHILDREN ↔ SOCIAL A ↔ RELIGION ↔ PHONE IN
↔ TRAVEL ↔ LEISURE ↔ JAZZ ↔ COUNTRY ↔ NA-
TIONAL ↔ OLDIES ↔ FOLK M ↔ DOCUMENT ↔
NEWS
PS
PTY
RT
Frequency
or
On the Unit On the Remote Control
Press the RDS MODE button within approx.
10 seconds again.
While searching, “SEARCH” and the selected PTY code alter-
nately appear on the display.
The Unit searches 30 preset stations and stops when it finds a
station of the category you have selected, then tunes into that
station.
3
PS (Program Service):
While searching, “PS” alternately appear on the display. Then, the
RDS indicator lights up and the station name appears. “NO PS” ap-
pears if no signal is sent.
PTY (Program Type):
While searching, “PTY” alternately appear on the display. Then,
the RDS indicator lights up and the broadcast program type ap-
pears. “NO PTY” appears if no signal is sent.
To continue searching after the first stop, press the RDS
MODE button again while the display indications blink.
If no program is found, “NOT” and “FOUND” alternately appear
on the display.
To stop searching at any time during the process, press
the RDS MODE button to stop search operation.
RT (Radio Text):
While searching, “RT” alternately appear on the display. Then, the
RDS indicator lights up and a text message sent by the station ap-
pears. “NO RT” appears if no signal is sent.
Station Frequency:
Station frequency (non-RDS service)
Descriptions of the PTY Codes
NEWS:
AFFAIRS:
News
Topical programs expanding on the current news
or affairs
• If searching finishes at once, “PS”, “PTY” and “RT” will not
appear on the display.
• If you press the DISPLAY MODE button while listening to
an AM (MW) station, the display only shows station fre-
quency.
INFO:
Programs on medical service, weather forecasts,
etc.
Sports events
SPORT:
EDUCATE: Educational programs
DRAMA:
Radio plays
• RDS is not available for AM (MW) broadcasts.
CULTURE: Programs on national or regional culture
SCIENCE:
VARIED:
POP M:
ROCK M:
MO.RM:
Programs on natural sciences and technology
Other programs like comedies or ceremonies
Pop music
Rock music
Middle-of-the road music (usually called “easy lis-
tening”)
On characters displayed
When the display shows PS, PTY or RT signals:
• The display shows upper case letters only.
• The display cannot show accented letters; For example, “A”
may represent accented “A’s” like “Á, Â, Ã, À, Ä and Å”.
LIGHT M:
Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE:
Reports on commerce, trading, the Stock Market,
etc.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
CHILDREN: Entertainment programs for children
SOCIAL A: Programs on social activities
RELIGION: Programs dealing with any aspect of belief or faith,
or the nature of existence or ethics
To temporarily switch to a broadcast program of
your choice
RDS mode is another convenient RDS service that allows this Unit
to switch temporarily to a broadcast program of your choice
(NEWS, TA or INFO) from the currently selected station, except
if you are listening to a non-RDS station (all AM (MW) stations or
some FM stations).
• The RDS function is only applicable to the preset stations. See
page 10.
• If an FM station does not broadcast RDS mode information,
RDS mode cannot be activated.
PHONE IN: Programs where people can express their views ei-
ther by phone or in a public form
TRAVEL:
LEISURE:
JAZZ:
Programs about travel destinations, package tours,
and travel ideas and opportunities
Programs concerned with recreational activities
such as gardening, cooking, fishing, etc.
Jazz music
COUNTRY: Country music
NATIONAL: Current popular music from another nation region,
in that country’s language
To select a program type
On the Unit
OLDIES:
FOLK M:
Classic pop music
Folk music
DOCUMENT: Programs dealing with factual matters, presented
in an investigative style
(twice)
On the Remote Control
(twice)
Press the RDS MODE button twice while lis-
tening to an FM station.
“E. SELECT” appears on the display.
1
Select the program type using the SELECT +
or – button within approx. 10 seconds.
The display shows a program type in the following order:
2
TA
NEWS
INFO
OFF
TA:
Traffic Announcement
NEWS: News
INFO: Programs on medical service, weather forecast, etc.
OFF: RDS mode off
Press the RDS MODE button within approx.
10 seconds again to set the selected pro-
3
gram type.
The selected program type indicator lights up on the display,
and the Unit enters RDS Standby mode.
• The RDS indicator lights up when tuned to a station which pro-
vides RDS mode information.
Case 1: If there is no station broadcasting the type of
program you have selected
The broadcast station being currently heard will continue to be
heard.
«
When a station starts broadcasting the program you have selected,
this unit automatically switches to the station. The program type
(TA, NEWS or INFO) indicator starts blinking.
«
When the program is over, this Unit goes back to the currently se-
lected station, but still remains in RDS Standby mode.
Case 2: If there is a station broadcasting the type of pro-
gram you have selected
This Unit tunes to the station broadcasting the program. The pro-
gram type (TA, NEWS or INFO) indicator starts blinking.
«
When the program is over, this Unit goes back to the currently se-
lected station, but still remains in RDS Standby mode.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
To stop listening to the program selected by RDS mode
Press the RDS MODE button. “OFF” appears and the program
type (TA, NEWS or INFO) indicator goes off on the display.
• In RDS standby mode, if you change the source or turn off
the power, RDS standby mode is canceled.
• When the RDS is being operated (i.e. the selected pro-
gram type is being received from the broadcast station)
and if the DISPLAY MODE or SELECT button is operated,
the station will not switch back to the current selected sta-
tion even after the program ends. The program type indi-
cator remains in the display, indicating that the RDS is in
standby mode.
• When the RDS is in standby mode and a radio broadcast
is being recorded, be careful because the RDS may be
activated and a different program than the intended one
may be recorded.
When the RDS mode is not required, release the RDS
mode.
• When the alarm signal is detected by RDS, the station
broadcasting alarm is received with priority. “ALARM!” is
not displayed.
CAUTION:
• When the sound alternated intermittently be-
tween the station tuned in by the RDS function
and the current selected station, cancel the RDS
mode. This does not constitute malfunction of
the unit.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
STANDBY/ON
Numeric
REPEAT
PROGRAM
RANDOM
keys
SLEEP
AUX
CD1-CD3
CD Open/
Close 0
FM MODE
FM /AM
4
¢
7
DISC SKIP
SET
7
CD1-CD3
CANCEL
¢
4
CD
CD1
CD2
CD3
¡
CD
6
REPEAT PROGRAM/RANDOM
22
TAPE
A/B
TAPE
REPEAT
CD 6
SELECT
RDS MODE DISPLAY MODE
VOLUME
PROGRAM
/RANDOM
SOUND
MODE
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
Track number, Playing time,
Program number, etc.
Program indicator
Disc indicators
RM-SMXKA6R REMOTE CONTROL
Random
indicator
Repeat
indicator
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
The CD Player has the rotational disc tray that can accommodate
3 CDs.
You can use Normal, Program, Random, or Repeat Play.
Disc Rotation indicator:Runs when the selected CD is
playing or paused. This indicator
goes out if a CD is not loaded for
the selected disc number.
Normal Play: Can continuously play all the tracks on all
the CDs.
Program Play: Can play all the programmed tracks on all
the CDs in the programmed order.
Random Play: Can play all the tracks on all the CDs in ran-
dom order.
Repeat Play: Can repeat all the tracks on all the CDs, the
tracks on one of the CDs, or just one of
tracks on one CD.
Once the tray is ejected, the Disc
Rotation indicators for all disc
numbers are lit. However, when
the empty disc number is select-
ed, the Disc Rotation indicator for
the disc number goes out.
Here are the basic things you need to know to play CDs and locate
the different tracks on them.
About the Disc Indicator
Disc Number
indicator
Disc Rotation
Selected Disc
indicator
indicator
The Disc indicator consists of the following three kinds of indica-
tors:
Disc Number indicator: Lights all the time.
Selected Disc indicator:Lights for the currently selected
disc number.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
❏ When you use an 8 cm (3'') CD, place it on the inner circle of the
tray.
Example of indication:
When CD tray has ejected once and then
CD1 is pressed. (DISC1 is selected)
❏ You can load CDs while listening to the other source or while
listening to the CD being played back.
Shows that the disc is
rotating.
❏ When power is turned off with the tray opened, the tray is auto-
matically closed.
Shows that this
disc number is
selected.
❏ If the CD cannot be read correctly (because it is scratched, for
example), “ 00. 00:00” appears on the display.
To Unload CDs
Take out the CD as shown below.
One Touch Play
The power comes on, and operations are done automatically.
While the CD Player is stopped, press the CD
1
❏ By pressing the CD 6button, the System will come on, and if
a CD is loaded for the disc number that was lastly selected, it
will start playing from the first track.
0
Open/Close
tray.
button on the Unit to open the
Remove the CD, then press the DISC SKIP
button on the Unit.
The tray turns for the next CD.
❏ By pressing the CD1-CD3 button, the System will come on, and
if a CD is already loaded for the selected disc number, it will
start play from the first track.
2
Repeat step 2 to remove all the CDs.
3
4
To Load CDs
0
Press the CD Open/Close
Unit to close the tray.
button on the
0
Press the CD Open/Close
Unit to open the tray.
button on the
1
2
❏ You can remove CDs while listening to the other source.
Place a CD, with its label side up, onto the
tray.
• You can also remove the CDs during playback. However,
in this case, you can only remove the CDs that are not be-
ing played back.
Be sure that the CD is securely seated on the disc tray.
With the label side up
CD
-R
/RW
PL
AY
BA
CK
Press the DISC SKIP button on the Unit and
place the next CD.
When you press the button, the tray turns for the next CD.
3
Repeat step 3 for the last CD.
4
5
0
Press the CD Open/Close
button on the
Unit.
The tray is closed.
• When placing a disc in the tray, be sure to position the
disc inside the recess correctly. Otherwise, the message
“NO DISC” will appear in the display, and the disc may be
damaged or the unit may be damaged when the tray is
opened, or it may be difficult to remove the disc from the
unit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
• Removing/changing the CDs during playback
While playing back a CD (e.g. CD1), you can remove or change
the other CDs (e.g. CD2 and CD3) by pressing the CD Open/Close
0 button. After removing or changing, press the same button to
close the tray.
Basics of Using the CD Player-
Normal Play
To Play CDs
To Select a Track
Load CDs.
1
2
4 ¢
button):
During playback (using the
or
Briefly press the 4or ¢button to select the track you want to
play.
Press one of the Disc button (CD1-CD3) you
want to play.
The selected disc number (e.g. “CD DISC 1” ) appears on the
display.
The first track of the selected CD begins playing. When the
first CD finishes playing, the next and the third CDs are con-
tinuously played back.
When the last CD has finished playing, the CD Player auto-
matically stops.
By pressing the button, you can skip to the next track or skip back
to the previous track.
• The selected track starts playing.
• Press the ¢ button once to skip to the beginning of the next
track. (You can skip to the next CD (e.g. CD1 = CD2 =
CD3).)
• Press the 4 button to skip to the beginning of the current
track. Press twice quickly to skip to the beginning of the previ-
ous track. (You cannot skip back to the previous CD.)
Examples:
CD1 =CD2 =CD3 =(stop)
CD2 =CD3 =CD1 =(stop)
4 ¢
button):
In Stop mode (using the
or
By briefly pressing the 4or ¢button, the CD Player operates
in the same way as during playback, except the following point.
• The buttons are effective only for the currently selected CD.
❏ You can start to play the currently selected disc by simply press-
ing the CD 6button.
Using the numeric keys on the Remote Control:
Using the numeric keys, you can directly select the track on the
currently selected CD.
While playing the CD, the following will appear on the display.
• The selected track starts playing.
For example, press +10, then 5 to play back the track number 15.
See “Entering the Number with the Remote Control” on page 8.
Search Play
Holding down the following buttons, during playback, will fast
forward/backwards the CD so you can quickly find a particular
passage in the track you are listening to.
Track number
Elapsed
playing time
CD is playing
• 22or ¡button on the Unit
• 4or ¢button on the Remote Control
• When the Disc button (CD1-CD3) is pressed with the tray
opened, the tray is closed and the selected CD automatically
begins playing.
To stop playing the CD, press the 7button. The following in-
formation for the CD is displayed.
Total track number
(After 3 seconds)
Total playing time
Track number
Playing time
To pause, press the CD 6button. The playing time indication
blinks on the display.
To cancel pause, press the CD 6button again. Play continues
from the point where it was paused.
To remove the CD, stop playing and press the CD Open/Close
0button on the Unit.
Tips:
• Playing back the CD using the DISC SKIP button
You can also play the CDs using the DISC SKIP button. During
playback, each time you press the button, the next CD is automat-
ically played back. If the next disc tray is empty, the disc tray is
automatically skipped.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
Repeat steps 3 and 4 to program other tracks
on the same CD or the other CD.
5
6
Programming the Playing Order
of the Tracks
6
To play the program, Press the CD
ton.
but-
You can program the playing order of the tracks on all the CDs.
Note that you can only make a program when the CD Player is
stopped.
For details, see “To Play the Program You Have Made” men-
tioned below.
❏ You can program up to 32 tracks in any desired order including
the same tracks.
To confirm the programmed contents, while the CD player
is stopped, press the 4or ¢button on the Remote Control.
To delete all the tracks in the program, while the CD Player
is stopped, press the 7button.
To Make a Program
To Modify the Program, while the CD Player is stopped, press
the CANCEL button, the last track in the program is deleted. To
add new tracks to the end of the program, repeat above steps 3 and
4.
Load CDs
1
2
In Stop mode, set the CD Player in Program
Play mode.
On the Unit
Press the PROGRAM button to light the “PRGM” indicator on the
display.
At the same time, “PROGRAM” appears on the display.
On the Remote Control
Press the PROGRAM/RANDOM button until “PROGRAM” ap-
pears on the display.
• If you try to program a track number that does not exists
on the CD, your entry will be ignored.
• If you try to program the 33rd track, “FULL” appears on
the display.
The “PRGM” indicator also lights up on the display.
Each time you press the button, the display changes as follows:
PROGRAM =RANDOM =Normal display (Normal Play) =
(back to the beginning)
• If a program is already made, the last step of the program will
be displayed.
To Play the Program You Have Made
Press the CD 6button.
The System plays the tracks in the order you have programmed
them.
• To use Repeat Play for Program Play, press the REPEAT but-
ton to select “ALL” or “1” before starting playback. For details,
see “Repeating Tracks” on page 18.
Press one of the Disc button (CD1-CD3) to
select the CD you want to program.
The display will change to the Program Entry display.
3
❏ You can skip to a particular program track by pressing the 4
or ¢button during Program Play.
CD1
CD 1
❏ To stop playing, press the 7button once. If you press the 7but-
ton, while the CD Player is stopped, the program is deleted.
or
To Exit and Re-enter Program Play
Disc number Track number
The program you have made is stored in memory. So, you can exit
Program Play temporarily or re-enter Program Play unless you de-
lete the program.
To exit the program mode once, while the CD Player is
stopped, press the PROGRAM button on the Unit or the PRO-
GRAM/RANDOM button on the Remote Control to light off the
“PRGM” indicator. By changing the source to the other (e.g. Tun-
er), the CD Player also exits Program Play mode.
Select the track you want to program.
4
Using the Unit
While the display is blinking, press the 4or ¢button to select
the track, then press the SET button within 5 seconds.
The program order number will be assigned from P-1.
To re-enter Program Play mode, press the PROGRAM or
PROGRAM/RANDOM button until the “PRGM” indicator lights
up again.
or
PRESET
Disc number Track number
SET
• Even when the power is turned off (standby or ECO
mode), the programmed tracks are not deleted. So, you
can re-enter Program Play mode.
Program order number
Using the Remote Control
Press the numeric keys to directly enter the track number. Then,
the program order number will be assigned from P-1.
• To delete the current program step, press the CANCEL button
on the Unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
Random Play
Tray Lock Function
The tracks of all the CDs will play in no special order when you
use this mode.
• To use Repeat Play for Random Play, press the REPEAT but-
ton to select “REPEAT ALL” or “REPEAT 1” before starting
playback. For details, see “Repeating Tracks”mentioned below.
In order to safely keep the CD in the CD Player, the tray can be
electronically locked.
When the electronic lock is on, the tray cannot be opened even if
the CD Open/Close 0button on the Unit is pressed.
Locking the Tray
In Stop mode, set the CD Player in Random
1
Turn on the System and enter CD mode.
Play mode.
1
2
On the Unit
While pressing down the 7button, press the
CD Open/Close
Press the RANDOM button to light the “RNDM” indicator.
At the same time, “RANDOM” appears on the display.
On the Remote Control
0
button on the Unit.
“LOCKED” appears on the display.
Press the PROGRAM/RANDOM button until the “RANDOM”
appears on the display.
The “RNDM” indicator also lights up on the display.
Each time you press the button, the display changes as follows:
PROGRAM =RANDOM =Normal display (Normal Play) =
(back to the beginning)
• If you try to open the tray by pressing the 0 button,
“LOCKED” appears on the display to let you know that the tray
has been locked.
6
Press the CD
button.
2
Unlocking the Tray
Repeat above steps 1 and 2.
“UNLOCKED” appears on the display.
The tracks on all the CDs are played in random order.
To stop playing, press the 7button.
To skip a track during playback, press the ¢ button to
jump to the next track in the random sequence.
To exit Random Play mode, while the CD Player is stopped,
press the RANDOM button on the Unit or the PROGRAM/RAN-
DOM button on the Remote Control again to light off the “RN-
DM” indicator. Normal Play resumes.
Now, you can use the tray normally.
Repeating Tracks
• Even after the system is unplugged, the tray lock condi-
tion will be retained for a few days. To unlock the tray after
powering up, you need to perform the unlocking opera-
tion.
You can repeat all tracks or individual track, as many times as you
like.
Press the REPEAT button.
The Repeat indicator changes with each press of the button, as fol-
lows:
REPEAT ALL=REPEAT 1DISC=REPEAT 1 = Blank dis-
play =(back to the beginning)
REPEAT ALL: In Normal Play mode, repeats all the tracks on
all the CDs.
In Program Play mode, repeats all the tracks in
the program.
In Random Play mode, repeats all the tracks on
all the CDs in random order.
REPEAT 1DISC: Repeats all tracks on one CD. (Selectable in
Normal Play only)
REPEAT 1:
Repeats one track.
To stop playing, press the 7button. Changing the source to the
other (e.g. Tuner) will also stop playing.
To exit Repeat mode, press the REPEAT button until the Re-
peat indicator on the display goes out.
❏ Repeat mode remains in effect during the following Play Mode
changing:
a. PROGRAM PLAY MODEÔNORMAL PLAY MODE
b. RANDOM PLAY MODE ÔNORMAL PLAY MODE
c. PROGRAM PLAY MODEÔRANDOM PLAY MODE
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Cassette Deck (Listening to a Tape)
STANDBY/ON
SLEEP
¡
AUX
7
FM MODE
FM /AM
7
4
TAPE A/B
TAPE 3
22
¢
CD
CD1
CD2
CD3
REPEAT PROGRAM/RANDOM
0EJECT
(Deck B)
0EJECT
(Deck A)
TAPE
A/B
TAPE
TAPE
3
TAPE A/B
SELECT
RDS MODE DISPLAY MODE
VOLUME
SOUND
MODE
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
RM-SMXKA6R REMOTE CONTROL
3: Tape indicator
Deck indicators
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
The Cassette Deck allows you to play, record, and dub audio tapes.
Close the cassette holder gently.
3
❏ Listening to type I tape is suitable for this Cassette Deck.
When both Deck A and Deck B contain a tape, the last deck to
have a tape inserted is selected.
The use of tapes longer than 120 minutes is not rec-
ommended, since characteristic deterioration may
occur and these tapes easily jam in the pinch-rollers
and the capstans.
The selected Deck is shown by the Deck indicator “A” or “B”.
For example, when the Deck A is selected, the Deck indicator
“A” lights up.
• To change the deck, press the TAPE A/B button. Each time
you press the button, Deck A or Deck B is alternately
selected.
One Touch Play
By pressing the TAPE 3button, the System will come on, and if
a tape is in the deck, it will start to play. If no tape is loaded, “NO
TAPE” appears on the display, the System will come on and wait
for you to insert a tape, or select another function.
3
Press the TAPE
button.
4
The Tape indicator (3) blinks on the display and the tape is
played back.
The Cassette Deck automatically stops when one side of the
tape has finished playing.
To stop playing, press the 7button.
To remove the tape, stop the tape, and press the 0EJECT part
to open the Cassette Holder.
Playing a Tape
You can use either Deck A or Deck B at a time for playback.
To Fast-Wind A Tape
0
Press the
EJECT part for the deck you
1
2
During playback or in Stop mode, press the ¡(FF) button on the
Unit to fast-wind the tape onto the right side of the cassette without
playing.(You can also use the ¢button on the Remote Control.)
During playback or in Stop mode, press the 22(REW) button on
the Unit to fast-wind the tape onto the left side of the cassette with-
out playing.(You can also use the 4button on the Remote Con-
trol.)
want to use.
When the cassette holder opens, put a cas-
sette in, with the exposed part of the tape
down, toward the base of the Unit.
The tape will travel from the left to right.
During fast-winding the tape, the Tape indicator (3) goes out.
During fast-winding, the status bar illumination at the bottom of
the display moves counterclockwise.
During rewinding, it moves clockwise.
• The Cassette Deck automatically stops when one side of the
tape has finished playing.
Tape travelling direction
❏ During fast-winding the tape, you can change the tape travelling
direction by pressing the ¡(FF) or 22(REW) button.
• If the cassette holder does not open, turn the System off,
then back on and press the 0EJECT part again.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Cassette Deck (Recording)
STANDBY/ON
REC START/STOP
SLEEP
PROGRAM
CD REC START
DUBBING
AUX
FM MODE
FM /AM
7
7
TAPE A/B
CD
CD1
CD2
CD3
0EJECT
(Deck B)
TAPE 3
REPEAT PROGRAM/RANDOM
0EJECT
(Deck A)
TAPE
A/B
TAPE
TAPE A/B
SELECT
RDS MODE DISPLAY MODE
VOLUME
TAPE
SOUND
MODE
3
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
RM-SMXKA6R REMOTE CONTROL
3: Tape indicator
Deck indicators
REC indicator
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
Recording onto a cassette from any of the sound sources is simple.
Just place a tape in Deck B, have the source ready, make one or
two settings, and you’re ready to record. For each source, the pro-
cedure is a little bit different so we explain each separately. But
first, here are a few things to make your recordings better.
• At the start and end of cassette tapes, there is leader tape
which cannot be recorded onto. Thus, when recording
CDs, radio broadcasts, etc., wind on the leader tape first
to ensure getting the beginning of the recording.
Things To Know Before You Start Recording
❏ It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the con-
sent of the owner of copyright in the sound or video
recording, broadcast or cable program and in any lit-
erary, dramatic, musical, or artistic content embodied
therein.
CAUTION:
• If a recording you make has excessive noise or
static, the Unit may have been too close to a TV
which was on during the recording. Either turn
off the TV or increase the distance between the
TV and the Unit.
❏ The recording level, which is the volume at which the new tape
is being made, is automatically set correctly, so it is not affected
by the VOLUME Control on the System. Also, it is not affected
by adjusting the sound effects. Thus, during recording, you can
adjust the sound you are actually listening to without affecting
the recording level.
❏ Two small tabs on the back of the cassette tape, one for side A
and one for side B, can be removed to prevent accidental erasure
or recording.
Adhesive tape
❏ To record on a cassette with the tabs removed, you must cover
the holes with adhesive tape first.
❏ Type I tape can be used for recording.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Cassette Deck (Recording)
Insert a blank or erasable tape into the Deck
B and wind past the tape leader.
Press the CD REC START button on the Unit.
“CD REC” appears on the display and the “REC” indicator
lights up. Then, the System begins CD Synchro Recording and
the tracks on the CD are recorded on the tape.
When recording of the tracks of all CDs is finished, “CD REC
FINISHED” scrolls on the display and the CD Player and Cas-
sette Deck stop.
2
3
Standard Recording
This is the basic method for recording any source. The System also
has special ways for recording CD to tape, and tape to tape, which
save you time and effort, as well as give you some special effects.
However, when you need to add a selection to a tape you have
made, or are combining selections from several sources on one
tape, use the method described below; just substitute the source
you want into this procedure, such as a tape in Deck A, a CD, or
the Tuner. You can also record from an external equipment with
this procedure.
(Recording start) (When finished)
CD REC
START
To Record Any Sound Source to Tape
Follow these steps to record from any sound source onto a tape in
Deck B.
• If the tab of the cassette tape on the Deck B is removed to
prevent erasure or recording, "NO REC" will appear on the
display.
• After the CD Player has played the entire CD or all the pro-
grammed tracks, the tape automatically stops.
Insert a blank or erasable tape into the Deck
B and wind past the tape leader.
1
To stop at any time during the recording process, press
the REC START/STOP button on the Unit or the 7 button. “CD
REC FINISHED” scrolls on the display and the CD Player and
Cassette Deck stop.
• When making SLEEP timer settings while doing CD Syn-
chro recording, set enough time to allow for the CD to fin-
ish playing, otherwise the power will go off before
recording is completed.
Tape travelling direction
Prepare the source, by, for example, tuning
in a radio station, loading CDs, or turning on
2
connected equipment.
• For CD recording, see “CD Synchro Recording” mentioned
below.
• For dubbing, see “Tape to Tape Recording (Dubbing)”
described below.
Tape to Tape Recording (DUB-
BING)
Press the REC START/STOP button on the
3
Recording from one tape to another is called dubbing.
You can dub tapes simply, with just a single button.
Unit.
The “REC” indicator lights up and the System begins record-
ing.
Press the TAPE3button, and then press the
7button.
1
The Tape indicator (3) blinks on the display.
• If the tab of the cassette tape on the Deck B is removed to
prevent erasure or recording, "NO REC" will appear on the
display.
Insert the source cassette you want to copy
from into Deck A for playback.
2
Insert a blank or erasable cassette you want
to copy onto into Deck B for recording.
To stop during recording, press the REC START/STOP but-
ton on the Unit, or press the 7button.
3
Recording an AM Station to Tape (Beat Cut)
When recording an AM broadcast, beats may be produced which
are not heard when listening to the broadcast. If this happens, press
the PROGRAM button on the Unit to eliminate the beats.
Press the DUBBING button on the Unit.
4
Deck A and Deck B will start simultaneously and the “REC”
indicator lights up.
During dubbing, the Deck indicators “A” and “B” light up al-
ternately.
• If no tape is inserted into Deck A, “NO TAPE” will appear
on the display.
• If no tape is inserted into Deck B, “NO TAPE” will appear
on the display.
Set to AM station and start recording.
1
2
Press the PROGRAM button on the Unit to
eliminate the beats.
Each time you press the button, the display changes as shown
below:
To stop dubbing, press the REC START/STOP button on the
Unit or the 7button.
CUT 1=CUT 2=CUT 3
=
CUT 4=(back to the beginning)
CD Synchro Recording
• During dubbing, you can hear sound effects through the
speakers or headphones. However, the sound is dubbed
without sound effects.
Everything on the CD goes onto the tape in the order it is on the
CD, or according to the order you have set in a program.
Prepare CDs. (See page 15.)
1
Press the CD1-3 button (that you want to make recording), and
then press the 7button.
• If you want to record specific tracks only, you need to pro-
gram the tracks beforehand. (See page 17.)
• If you want to record one CD only, you need to load one
CD only.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using an External Equipment
STANDBY/ON
SLEEP
AUX
AUX
FM MODE
FM /AM
CD
CD1
CD2
CD3
REPEAT PROGRAM/RANDOM
AUX
TAPE
A/B
TAPE
SELECT
RDS MODE DISPLAY MODE
VOLUME
SOUND
MODE
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
RM-SMXKA6R REMOTE CONTROL
Listening to the External
Equipment
You can listen to the external equipment such as MD recorder, cas-
sette deck, or other auxiliary.
❏ First, make sure that the external equipment is properly connect-
ed to the System. (See page 6.)
Set the volume level to the minimum posi-
tion.
1
Press the AUX button.
“AUX IN” appears on the display.
2
Start playing the external equipment.
3
4
Adjust the volume level to the level you want
listen to.
Apply the following sound effects, if you
5
wish.
• ACTIVE BASS EX. (See page 8.)
• SOUND TURBO (See page 8.)
• Sound Mode (See page 8.)
To exit AUX mode, select other source (e.g. Tuner).
• For operation of the external equipment, refer to its In-
structions.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
STANDBY/ON
SLEEP
SLEEP
AUX
¢
4
FM MODE
FM /AM
CLOCK/TIMER
CD
SET
CD1
CD2
CD3
REPEAT PROGRAM/RANDOM
TAPE
A/B
TAPE
SELECT
RDS MODE DISPLAY MODE
VOLUME
SOUND
MODE
FADE
MUTING
ACTIVE
SOUND
BASS EX. TURBO
DAILY Timer indicator
RM-SMXKA6R REMOTE CONTROL
Timer indicator
REC (Recording) Timer indicator
SLEEP indicator
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
The timers lets you control recording and listening functions auto-
matically.
display appears on the display. (In the clock setting display,
the hour digits of the current clock blink on the display.
)
Three types of timers are available:
DAILY Timer
Use this timer to set wake up everyday to music from any
source, instead of an alarm clock.
REC (Recording) Timer
Unattended recording of radio broadcasts. You can set the
starting time and ending time.
• If the clock is already set, the display changes as follows
each time you press the CLOCK/TIMER button.
TIMER = ON time = REC = ON time = Clock setting
display =Canceled =(back to the beginning)
SLEEP Timer
Fall asleep and have your System turn off automatically after
a certain length of time.
4 ¢
button to set the hour.
Press the
or
2
3
Pressing the ¢button moves the time forwards and pressing
the 4button moves it backwards. Holding down the button
moves the hour rapidly.
Setting the Clock
Press the SET button.
The minute digits of the time indication blink on the display.
• To return to the hour setting, press the CANCEL button.
When you plug the AC power cord into the wall outlet, the time in-
dication “0:00” blinks on the display.
You can set the clock whether the System is on or off.
4 ¢
button to set the
Press the
minute.
or
4
5
• The clock must be correctly set for the timers to work.
Press the SET button.
“CLOCK OK” appears on the display. Then, the selected time
• Each setting step must be completed within approx. two
minutes. Otherwise, the setting is cleared and must be re-
peated from the beginning.
is set and the seconds start counting from 0.
• The clock may gain or lose one to two minutes per month.
CAUTION:
• If there is a power failure, the clock loses its set-
ting immediately. “0:00” blinks on the display
and the clock must be reset.
Using the Unit
Press the CLOCK/TIMER button.
1
The hour digit of the time indication blinks on the display.
• If the clock is already set and “0:00” is not blinking, press
the CLOCK/TIMER button repeatedly until clock setting
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
2. Press the ¢or 4button to set the minute, then press the
SET button.
Setting the Daily Timer
Once you have set the Daily Timer, the timer will be activated at
the same time every day.
The Timer indicator ( ) and “DAILY” indicator on the display
shows that the Daily Timer you have set is in effect.
You can set the Daily Timer whether the System is turned on or
off.
“OFF TIME” appears and then the System enters OFF-time
setting mode. The current OFF time appears on the display,
and the hour digits blink.
• Perform each setting within approx. 30 seconds. Other-
wise, setting will be cleared and the procedure must be
repeated from the beginning.
• If you have made a mistake while setting the timer, press
the CANCEL button on the Unit. However, this does not al-
ways cancel the current setting. If the CANCEL button
does not work, press the CLOCK/TIMER button on the
Unit repeatedly until the display returns to the original dis-
play, and start from the first step.
Setting the OFF time (Example: 13:15).
1. Press the ¢ or 4 button to set the hour you want the
System to be turned off, then press the SET button.
The minute digits of the ON time blink on the display.
4
Using the Unit
Press the
button to turn on the System.
1
2
Press the CLOCK/TIMER button until “ON
TIME” immediately after “TIMER” appears on
the display.
At this time, “DAILY” indicator blinks and the Timer indica-
tor ( ) lights up on the display.
Each time you press the button, the display changes as follows:
TIMER =ON TIME* =REC =ON TIME =Clock setting
display =Canceled =(back to the beginning)
*: This item should be selected for the Daily Timer setting.
2. Press the ¢or 4button to set the minute, then press the
SET button.
Then, the System enters ON-time setting mode, and the current
ON time appears on the display and the hour digits blink.
The System enter Music Source Selecting mode and “TUN-
ER FM” blinks on the display.
Selecting the music source.
5
Setting the ON time (Example: 10:15).
1. Press the ¢ or 4 button to set the hour you want the
System to come on, then press the SET button.
The minute digits of the ON time blink on the display.
Pressing the ¢button moves the time forwards and press-
ing the 4button moves it backwards.
3
Press the ¢ or 4 button to select the music source you
want to listen to, then press the SET button.
Each time you press the ¢or 4button, the display chang-
es as shown below:
TUNER FM =TUNER AM =– CD – – =TAPE =AUX
IN =(back to the beginning)
According to the music source you have selected, the next op-
eration differs.
Holding down the button moves the time rapidly.
TUNER FM: Tunes in to the specified preset FM station.
TUNER AM: Tunes in to the specified preset AM station.
– CD – – :
TAPE:
Plays the specified track on the specified CD.
Plays a tape in Deck A.
AUX IN:
Plays an external source.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
Preparation for each music source:
Perform the following operation according to the music source
you have selected. Then, the System enters Volume Setting
mode.
When selecting TUNER FM or TUNER AM:
Press the ¢ or 4 button to select the preset station
number, then press the SET button.
• If the System is already on when the timer ON-time
comes, the Daily Timer does not work.
Turning the Daily Timer On and Off
Once you have set the Daily Timer, it is stored in memory. So, the
Daily Timer will be activated at the same time every day until it is
canceled.
When selecting – CD – – :
Be sure to specify the disc number and the track number as fol-
lows.
1. Press the ¢or 4button to select the disc number, then
press the SET button.
Each time you press the button the disc number changes as
follows:
– CD – – =1 CD – – =2 CD – – =3 CD – – =(back
to the beginning)
• If no disc number is specified, playback will start from the
first track of the currently selected disc.
To cancel the Daily Timer temporarily:
Press the CLOCK/TIMER button on the Unit
repeatedly until the “TIMER” appears on the
1
display.
Press the CANCEL button on the Unit.
The “DAILY” indicator goes out and “OFF” appears on the
2
2. Press the ¢or 4button to select the track number, then
press the SET button.
display.
The Timer indicator ( ) goes out and the Daily Timer is can-
celed temporarily.
For example: 2 CD12 (Disc number 2, Track number 12)
Set Daily timer CD2 after playing in CD2.
If you set Daily Timer to other CD number after playing
CD2, it will not play back at the setting time.
• If no track number is specified, playback will start from
the first track of the specified disc.
To activate the cancelled Daily Timer:
Press the CLOCK/TIMER button on the Unit
repeatedly until the “TIMER” appears on the
1
When selecting TAPE:
Insert a cassette tape you want to play into Deck A.
When selecting AUX:
Prepare the external equipment so that it will turn on at the ON
time set by the System.
display.
The “DAILY” indicator blinks and the Timer indicator (
)
lights up on the dispaly.
To allow this, the equipment should have the timer function.
Press the SET button on the Unit.
2
“SET” and “OK” successively appear on the display. The Tim-
er indicator ( ) and the “DAILY” indicator remain lit, and
the display returns to the original display.
Setting the volume level.
6
Press the ¢or 4button to select the volume level.
VOL – – : The current volume level will be used.
VOL5, 10, or 15: When the timer is turned on, the Volume
will be automatically set to the selected level.
CAUTION:
• If the System is unplugged, or a power failure oc-
curs, the timer setting will be lost in a few days.
You will need to reset the clock first, then the
timer.
Press the SET button.
The timer setting is completed, and “SET” and “OK” succes-
sively appear on the display. Then the display returns to the
display before you set the Timer.
7
Setting the REC (Recording)
Timer
With the Recording Timer, you can make a tape of a radio broad-
cast automatically whether or not you are home.
Press the
button to turn off the System.
8
The Timer indicator ( ) and “DAILY” indicator are lit on the
display, showing that the Daily Timer is set to on.
To confirm / change the timer setting, repeat the setting pro-
cedure from the beginning.
• You can set the REC Timer whether the System is on or
off.
• The volume level is automatically set to MIN when REC
Timer is used.
• Perform each setting within approx. 30 seconds. Other-
wise, setting will be cleared and the procedure must be
repeated from the beginning.
• If you have made a mistake while setting the timer, press
the CANCEL button on the Unit. However, this does not al-
ways cancel the current setting. If the CANCEL button
does not work, press the CLOCK/TIMER button on the
Unit repeatedly until the display returns to the original dis-
play, and start from the first step.
When the timer ON-time comes:
The following operation will be automatically repeated every day.
• When the timer ON-time comes, and the System automatically
turns on. The music source you have set is played. The Timer
indicator ( ) blinks and “DAILY” indicator lights during
timer operation.
• When the timer OFF-time comes, “OFF” blinks on the display
just before the OFF-time and the System automatically turns
off. Then, the Timer indicator ( ) and “DAILY” indicator
remain lit on the display.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
When the timer ON-time comes:
• When the timer ON-time comes, the System automatically
turns on. The station you have set is played. The Timer indica-
Using the Unit
You can set the time in the same way as for setting the Daily Tim-
er.
tor ( ) blinks during timer operation.
To stop timer recording, press the 7button.
• When the timer OFF-time comes, “OFF” blinks on the display
just before the OFF-time and the System automatically turns
off.
Insert a blank or erasable tape into the Deck
B and wind past the tape leader.
1
Press the CLOCK/TIMER button until “ON
TIME” immediately after “REC” appears on
2
the display.
The Timer indicator ( ) lights and the “REC” indicator
blinks.
• The REC Timer works even if the System is turned on.
Each time you press the button, the display changes as follows:
DAILY =ON TIME =REC =ON TIME* =Clock setting
display =Canceled =(back to the beginning)
*: This item should be selected for the REC Timer setting.
Turning the REC (Recording) Timer On and Off
Once you have set the REC Timer to record a source, the timer set-
ting is stored in memory. So, though the REC Timer turns off once
it is used, you can recall it at any time.
Then, the System enters ON-time setting mode. The current
ON time appears on the display and the hour digits blink.
To cancel the REC Timer temporarily:
Press the CLOCK/TIMER button on the Unit
repeatedly until “REC” appears on the dis-
1
play.
Press the CANCEL button on the Unit.
“OFF” appears and both the Timer indicator ( ) and the
“REC” indicator go out.
2
To activate the cancelled REC Timer:
Setting the ON time you want the System to
3
Press the CLOCK/TIMER button on the Unit
1
turn on.
repeatedly until “REC” appears on the dis-
1. Press the 4or ¢button to set the hour, then press the
play.
SET button.
The Timer indicator ( ) lights and the “REC” indicator
blinks on the display.
2. Press the 4or ¢button to set the minute, then press the
SET button.
“OFF TIME” appears and then the System enters OFF-time
setting mode. The current OFF time appears on the display,
and the hour digits blink.
Press the SET button on the Unit.
“SET” and “OK” successively appear on the display. The Tim-
er indicator ( ) and the “REC” indicator remain lit, and the
display returns to the original display.
2
Setting the OFF time you want the System to
4
turn off.
CAUTION:
1. Press the 4or ¢button to set the hour, then press the
SET button.
• If the System is unplugged, or a power failure oc-
curs, the timer setting will be lost in a few days.
You will need to reset the clock first, then the
timer.
2. Press the 4or ¢button to set the minute, then press the
SET button.
The System enters Preset Station Entering mode.
Select the preset station for recording.
1. Press the 4or ¢button to set the band (TUNER FM or
5
TUNER AM), then press the SET button.
2. Press the 4or ¢button to set the preset number, then
press the SET button.
“SET” and “OK” successively appear on the display. The
“REC” indicator stops blinking and remains lit.
Press the
if necessary.
button to turn off the System,
6
To confirm / change the timer setting, repeat the setting pro-
cedure from the beginning.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
Setting the SLEEP Timer
Timer Priority
Use the Sleep Timer to turn the System off after a certain number
of minutes when it is playing. By setting the Sleep Timer, you can
fall asleep to music and know that your System will turn off by it-
self rather than play all night.
Since each timer can be set independently, you may wonder what
happens if the settings overlap. Here are the priorities for each timer:
The REC Timer always has priority. This means that:
• If other timer is set to come on during a time when the REC
Timer is operating, the other timer just won’t come on at all,
so you will always get the entire program on a tape.
• If the REC Timer is set to come on while other timer is oper-
ating, the other timer will turn off just before the REC Timer
is set to turn on, and the REC Timer will then take over.
• You can only set the Sleep Timer when the System is on.
Using the Remote Control
During playback a source, press the SLEEP
1
button.
❏ If the SLEEP Timer is set while DAILY Timer is operating, the
DAILY Timer settings are cancelled. However, if DAILY Tim-
er is set to come on while the SLEEP Timer is operating, the
SLEEP Timer setting will be cancelled and the System will use
the settings from the DAILY Timer.
The “SLEEP” indicator starts blinking on the display.
Set the length of time you want the source to
play before shutting off.
Each time you press the SLEEP button, the time length chang-
es as follows:
2
Example 1
10 =20 =30 =60 =90 =120 =Cancelled =(back to
Setting
the beginning)
ON
OFF
REC Timer
OFF
SLEEP Timer
Wait for 5 seconds.
The “SLEEP” indicator stops blinking and remains lit, and the
display returns to the original one before setting the Sleep
Timer.
3
22:00
22:30
23:00
The System is now set to turn off after the number of minutes
you have set.
Operation
ON
OFF
REC Timer
To Confirm the Sleep Time:
When the SLEEP button on the Remote Control is pressed, the re-
maining sleep time is displayed. Wait until the display returns to
the original display.
SLEEP Timer
To Cancel the SLEEP Timer Setting:
Press the SLEEP button on the Remote Control until the “SLEEP”
indicator goes out on the display.
22:00
22:30
The REC Timer has priority.
• Turning off the System also cancels the SLEEP Timer.
Example 2
Setting
ON
OFF
• When the SLEEP button is used without setting the clock,
“CLOCK ADJUST” appears on the display. You need to
set the clock beforehand.
REC Timer
OFF
ON
DAILY Timer
21:30
22:00
22:30
23:00
Operation
ON
OFF
REC Timer
DAILY Timer
21:30
22:30
The REC Timer has priority.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Care And Maintenance
Handle your CDs and tapes carefully, and they will last a long
time.
Cassette Tapes
• If the tape is loose in its cassette, take up
the slack by inserting a pencil in one of
the reels and rotating.
• If the tape is loose, it may get stretched,
cut, or caught in the cassette.
Compact Discs
• Only CDs bearing these marks can be
used with this System. However, contin-
ued use of irregular shape CDs (heart-
shape, octagonal, etc.) can damage the
System.
Recordable
• Do not touch the tape surface.
ReWritable
• Do not store the tape:
- In dusty places
- In direct sunlight or heat
- In moist areas
- On a TV or speaker
- Near a magnet
• Remove the CD from its case by holding
it at the edges while pressing the case’s
center hole lightly.
• Do not touch the shiny surface of the
CD, or bend the CD.
Cassette Deck
• If the heads, capstans, and pinch-rollers of the Cassette Deck
become dirty, the following will occur:
- Loss of sound quality
- Discontinuous sound
- Fading
- Incomplete erasure
- Difficulty recording
• Clean the heads, capstans, and pinch-rollers using a cotton
swab moistened with alcohol.
• Put the CD back in its case after use to
prevent warping.
• Be careful not to scratch the surface of
the CD when placing it back in the case.
• Avoid exposure to direct sunlight, tem-
perature extremes, and moisture.
• A dirty CD may not play correctly. If a
CD does become dirty, wipe it with a
soft cloth in a straight line from center to
edge.
Pinch-roller
Capstan
CAUTION:
• Do not use any solvent (for example, conven-
tional record cleaner, spray thinner, benzine,
etc.) to clean a CD.
Heads
General Notes
• If the heads become magnetized, the Unit will produce noise or
lose high frequencies.
• To demagnetize the heads, turn off the Unit, and use a head
demagnetizer (available at electronics and record shops).
In general, you will have the best performance by keeping your
CDs and the mechanism clean.
• Store CDs in their cases, and keep them in cabinets or on
shelves.
• Keep the System’s Top Cover closed when not in use.
Moisture Condensation
Moisture may condense on the lens inside
the System in the following cases:
• After turning on heating in the room.
• In a damp room.
• If the System is brought directly from a
cold to a warm place.
Should this occur, the System may mal-
function. In this case, leave the System
turned on for a few hours until the moisture
evaporates, unplug the AC power cord, and
then plug it in again.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• If you are having a problem with your System, check this list for a possible solution before calling for service.
• If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as
your dealer, for service.
Symptom
No sound is heard.
Possible Cause
Action
• Connections are incorrect, or loose.
• Check all connections and make cor-
rections. (See pages 4 to 6.)
• Headphones are connected.
• The antenna is disconnected.
• Disconnect the headphones.
Poor radio reception
• Reconnect the antenna securely.
• The AM (MW) Loop Antenna is too • Change the position and direction of
close to the System. the AM (MW) Loop Antenna.
• The FM Wire Antenna is not prop- • Extend FM Wire Antenna to the best
erly extended and positioned.
reception position.
The disc tray does not open.
• The AC power cord is not plugged in.
• Tray is locked.
• Plug the AC power cord.
• Unlock the tray. (See page 18.)
The CD skips.
The CD is dirty or scratched.
The CD is upside down.
Clean or replace the CD. (See page 28.)
Put the CD in with the label side up.
The CD does not play.
The cassette holder cannot be opened.
During tape playing, the power cord Plug in the power cord, and turn on the
was unplugged. System.
Unable to record.
Cassette record protect tabs are re- Cover holes on back edge of cassette
moved. with tape.
Unable to operate the Remote Control.
• The path between the Remote Con- • Remove the obstruction.
trol and the sensor on the Unit is
blocked.
• The batteries have lost their charge.
• Replace the batteries.
Operations are disabled.
The built-in microprocessor has mal- Unplug the System then plug it back in.
functioned due to external electrical in-
terference.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Amplifier
Output Power 100 W per channel, min. RMS, driven into 6 Ω at 1kHz, with no
more than 10% total harmonic distortion (IEC268-3)
55 W per channel, min. RMS, driven into 6 Ω at 1kHz, with no more
than 0.9% total harmonic distortion (DIN)
Input Sensitivity/Impedance (1 kHz)
AUX IN 300 mV/50 kΩ
Speaker terminals 6 - 16 Ω
PHONES 32 Ω - 1 kΩ
15 mW/ch output into 32 Ω
Cassette Deck Section
Frequency Response
Type I (NORMAL) 63 Hz - 12 500 Hz
Wow And Flutter 0.15% (WRMS)
CD Player
CD Capacity 3 CDs
Dynamic Range 85 dB
Signal-To-Noise Ratio 85 dB
Wow And Flutter Unmeasurable
Tuner
FM Tuner
Tuning Range 87.50 MHz - 108.00 MHz
AM Tuner
Tuning Range (MW) 522 kHz - 1 629 kHz
Unit
Dimensions 267 mm
✕
305 mm
✕
433 mm (W/H/D)
Mass Approx. 8.7 kg
Accessories
AM (MW) Loop Antenna (1)
Remote Control (1)
Batteries R6P (SUM-3)/AA (15F) (2)
FM Wire Antenna (1)
Power Specifications
Power Requirements AC 230 V , 50 Hz
Power Consumption 100 W (power on mode)
17 W (in Standby mode)
Approx. 1 W (in ECO mode)
Design and specifications are subject to change without notice.
VICTOR COMPANY OF JAPAN, LIMITED
EN
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
0303NYMCREBET
INSTRUCTIONS
SPEAKER SYSTEM
SP-MXKA6/SP-MXKA3
BEDIENUNGSANLEITUNG: LAUTSPRECHERSYSTEM
MANUEL D’INSTRUCTIONS: SYSTEME DES ENCEINTES
GEBRUIKSAANWIJZING: LUIDSPREKERSYSTEEM
MANUAL DE INSTRUCCIONES: SISTEMA DE ALTAVOCES
ISTRUZIONI: SISTEMA DI ALTOPARLANTI
BRUKSANVISNING: HÖGTALARSYSTEM
VEJLEDNING: HØJTTALERSYSTEM
KÄYTTÖOHJE: KAIUTINJÄRJESTELMÄ
Thank you for purchasing JVC speakers.
Grazie per aver acquistato questi altoparlanti della JVC.
Before you begin using them, please read the instructions carefully to
be sure you get the best possible performance. If you have any ques-
tions, consult your JVC dealer.
Prima di cominciare l’uso degli altoparlanti, leggete attentamente le
istruzioni per assicurare le migliori prestazioni. Qualora sorgessero
dei dubbi, rivolgetevi al vostro rivenditore JVC.
Vielen Dank für den Kauf dieser JVC-Lautsprecher.
Tack för ditt val av dessa JVC-högtalare.
Lesen Sie bitte diese Bedienungsanleitung vor Ingebrauchnahme
sorgfältig durch, um stets optimale Ergebnisse zu erzielen. Wenden
Sie sich bei etwaigen Fragen bitte an Ihren JVC Händler.
Innan du kopplar in högtalarna i din ljudanläggning bör du för att få
maximala prestanda från högtalarna läsa igenom bruksanvisningen
noggrant. Kontakta din JVC-återförsäljare om du har frågor eller känner
dig osäker.
Nous vous remercions pour l’achat de ces enceintes JVC.
Tak for købet af JVC-højttalerne.
Avant de les utiliser, lire ces instructions avec attention pour en obtenir
les meilleures performances possibles. En cas de questions, con-
sulter votre revendeur JVC.
Gennemlæs venligst vejledningen omhyggeligt før de tages i brug,
så De kan opnå den bedst mulige ydelse. Forhør hos Deres JVC
forhandler hvis De har nogen spørgsmål.
Dank u voor de aanschaf van deze JVC luidsprekers.
Kiitos siitä ettë päädyit valinnassasi JVC-kaiuttimiin.
Lees alvorens over te gaan tot aansluiten, deze gebruiksaanwijzing
door zodat u de best mogelijke prestaties zult verkrijgen. Neem kontakt
op met de JVC dealer indien u vragen heeft.
Ennen kuin alat käyttää niitä, lue käyttöohje huolellisesti, jotta ne
toimisivat parhaalla mahdollisella tavalla. Jos Sinulla on kysyttävää
ota yhteys JVC-edustajaan.
Le estamos muy agradecidos por haber adquirido estos altavoces de
JVC.
Antes de utilizarlos, sirvase leer las instrucciones detenidamente a
fin de obtener el mejor rendimiento posible. Si tienenaluna pregunta,
acuda a su agente de JVC.
— SAFETY INSTRUCTIONS —
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet
Switch off using the switch on the equipment and make sure that
international safety standards but, like any electrical equipment, care
must be taken if you are to obtain the best results and safety is to be
assured.
your family know how to do this.
Special arrangements may need to be made for infirm of handi-
capped people.
DON’T use equipment such as personal stereos or radios so that
you are distracted from the requirements of traffic safety. It is illegal
to watch television whilst driving.
Do read the operating instructions before you attempt to use the
equipment.
Do ensure that all electrical connections (including the mains plug,
extension leads and interconnections between pieces of equipment)
are properly made and in accordance with the manufacturer’s
instructions. Switch off and withdraw the mains plug when making or
changing connections.
DON’T listen to headphones at high volume as such use can
permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with
curtains or soft furnishing.
Overheating will cause damage and shorten the life of the equip-
ment.
Do consult your dealer if you are ever in doubt about the installation,
operation or safety of your equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws
— to ensure complete safety always fit the manufacturer’s approved
stand or legs with the fixings provided according to the instructions.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt
about it working normally, or if it is damaged in any way — switch
off, withdraw the mains plug and consult your dealer.
DON’T allow electrical equipment to be exposed to rain or
moisture.
ABOVE ALL
DON’T remove any fixed cover as this may expose dangerous
voltages.
– NEVER let anyone, especially children, push anything into holes,
slots or any other opening in the case.
DON’T leave equipment switched on when it is unattended unless it
is specifically stated that it is designed for unattended operation or
has a standby mode.
– this could result in a fatal electrical shock;
– NEVER guess or take chances with electrical equipment of any
kind
– it is better to be safe than sorry!
LVT1058-001A
[E]
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION
Connection/Anschluß/Raccordement/Aansluiting
Conexión/Collegamento/Ansluiting/Tilslutning/Liitäntä
• DON’T use other amplifier to operate this speaker system
except for CA-MXKA3/CA-MXKA6.
SP-MXKA3
Left speaker
Linker Lautsprecher
Right speaker
Rechter Lautsprecher
• Turn off power to the whole system before connecting the
speakers to the amplifier.
Enceinte de gauche
Enceinte de droite
Linker spreker
Altavoz izquierdo
Rechter spreker
Altavoz derecho
• The maximum power handling capacity of the SP-MXKA3 is
45 W/SP-MXKA6 is 100W. Excessive input will result in ab-
normal noise and possible damage. In cases where the sig-
nals described below are applied to the speakers, even if the
signals are below the maximum allowable input, they may
cause an overload and burn the wiring of the speakers. Be
sure to lower the amplifier volume beforehand.
Altoparlante sinistro
Altoparlante destro
Vänster högtalare
Höger högtalare
Venstre højttaler
Vasen kaiutin
Højre højttaler
Oikea kaiutin
RED
ROT
ROUGE
ROOD
ROJO
1) Noise during FM tuning.
2) High level signals containing high frequency components
produced by a tape deck in the fast forward mode.
3) Click noise produced when turning power of other compo-
nents on and off.
ROSSO
RÖD
RØD
PUNAINEN
4) Click noise produced when connecting or disconnecting
cords with the power on.
5) Click noise produced when the cartridge is replaced with
the power on.
BLACK
SCHWARZ
NOIR
ZWART
NEGRO
NERO
SVART
SORT
BLACK
SCHWARZ
NOIR
ZWART
NEGRO
NERO
SVART
SORT
6) Click noise produced when operating amplifier switches.
7) Continuous high frequency oscillation or high pitch electroni-
cally produced musical instrument sound.
8) Howling when using a microphones.
MUSTA
MUSTA
Amplifier output terminals
Ausgang des Verstärkers
Bornes de sortie de l’amplificaterur
Uitgangsaansluitengen van de versterker
Terminales de salida de amplificador
Terminali de uscita dell’amplifcator
Utgångar på förstärkaren
Forstærkerudgangsbøsninger
Vahvistimen ulostuloliittimet
SPECIFICATIONS
Type
: 3-way 3-speaker Bass-Reflex
Type
SP-MXKA6
Right speaker
Left speaker
Speakers
SP-MXKA3
Woofer
Rechter Lautsprecher
Enceinte de droite
Rechter spreker
Altavoz derecho
Altoparlante destro
Höger högtalare
Højre højttaler
Linker Lautsprecher
Enceinte de gauche
Linker spreker
: 13.5 cm cone × 1
Midrange
Tweeter
SP-MXKA6
Woofer
: 5.0 cm cone × 1
Altavoz izquierdo
Altoparlante sinistro
Vänster högtalare
Venstre højttaler
Vasen kaiutin
: 2.0 cm dome × 1
RED
ROT
: 16.0 cm cone × 1
Oikea kaiutin
ROUGE
ROOD
ROJO
ROSSO
RÖD
Midrange
Tweeter
Power Handling Capacity
SP-MXKA3
SP-MXKA6
Impedance
Frequency Range
Sound Pressure Level
SP-MXKA3
: 5.0 cm cone × 1
: 2.0 cm dome × 1
: 45 W
: 100 W
RØD
PUNAINEN
: 6 Ω
BLACK
SCHWARZ
NOIR
ZWART
NEGRO
NERO
BLACK
SCHWARZ
NOIR
ZWART
NEGRO
NERO
: 45 Hz ~ 22 000 Hz
: 89 dB/W·m
: 87 dB/W·m
SP-MXKA6
SVART
SORT
MUSTA
Dimensions (W × H × D)
SP-MXKA3
SVART
SORT
MUSTA
: 228 mm × 316 mm × 258mm
: 244mm × 321 mm × 258mm
SP-MXKA6
Amplifier output terminals
Ausgang des Verstärkers
Mass
SP-MXKA3
SP-MXKA6
: 3.1 kg each
: 3.6 kg each
Bornes de sortie de l’amplificaterur
Uitgangsaansluitengen van de versterker
Terminales de salida de amplificador
Terminali de uscita dell’amplifcator
Utgångar på förstärkaren
Design and specifications subject to change without notice.
Forstærkerudgangsbøsninger
Vahvistimen ulostuloliittimet
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ANSCHLUSS
RACCORDEMENT
• Verwenden Sie zum Betrieb dieses Lautsprechersystems keinen
anderen Verstärker, ausgenommen CA-MXKA3/CA-MXKA6.
• NE PAS utiliser d’autre amplificateur que le CA-MXKA3/CA-
MXKA6 pour faire fonctionner les enceintes.
•
Schalten Sie vor dem Anschluß der Lautsprecher an den Verstärker
die Spannungsversorgung des gesamten Systems aus.
• Mettre hors circuit tout le système avant de raccorder les
enceintes à l’amplificateur.
•
D
ie maximale Belastbarkeit von SP-MXKA3 ist 45 W und die
• La puissance maximale admissible du SP-MXKA3 est de 45
W, et celle du SP-MXKA6 de100W. En dépassant la puissance
admissible, cela provoquera des bruits anormaux et détériorera
les enceintes. Au cas où les signaux décrits ci-dessous sont
envoyés aux enceintes, et même si ces signaux sont inférieurs
à la puissance d’entrée maximum admissible, ils risquent de
provoquer une surcharge ou même un incendie. S’assurer de
bien diminuer le volume sonore de l’amplificateur.
von SP-MXKA6 ist 100W. Eine Überlastung führt zu Verzerrungen
und möglicherweise zu Beschädigungen. Signale der unten
beschriebenen Art können, auch wenn sie unter dem maximal
zulässigen Eingang liegen, eine Überlastung verursachen und
die Lautsprecherwicklungen durchbrennen. Verringern Sie
vorher die Lautstärke des Verstärkers.
1) Geräusche beim Einstellen von UKW-Sendern.
2) Hochpegelige Signale mit Hochfrequenz-Anteilen, die von
Tonbanddecks beim Schnellvorspulen erzeugt werden.
3) Klickgeräusche, wenn die Spannungsversorgung anderer
Komponenten ein-und ausgeschaltet wird.
1) Parasites durant une syntonisation FM.
2) Signaux de niveau élevé contenant des composants à haute
fréquence, comme ceux générés par une platine
d’enregistrement en mode avance rapide.
3) Cliquetis se produisant lorsque d’autres appareils sont mis
en ou hors circuit.
4) Klickgeräusche, wenn Kabel angeschlossen oder abgetrennt
werden, während die Spannungsversorgung eingeschaltet ist.
5) Klickgeräusche, wenn der Tonabnehmer des Plattenspielers
ausgewechselt wird, während die Spannungsversorgung
eingeschaltet ist.
4) Cliquetis se produisant lorsque des appareils sont branchés
ou dé-branchés alors que leur alimentation est en circuit.
5) Cliquetis se produisant lorsque la cellule d’une platine tourne-
disque est changée alors que l’alimentation est en circuit.
6) Cliquetis se produisant lorsque les commandes de
l’amplificateur sont manipulées.
6) Klickgeräusche, die beim Betätigen von Schaltern des
Verstärkers erzeugt werden.
7) Ständige Hochfrequenzschwingungen oder elektronisch
erzeugte Töne von Musikinstrumenten mit hohen Tonhöhen.
8) Rückkopplungen von Mikrofonen.
7) Oscillations continuelles à haute fréquence ou sons très aigus
provenant d’instruments de musique électroniques.
8) Hurlements dus à l’utilisation de micros.
CARACTÉRISTIQUES
TECHNISCHE DATEN
Type
:Enceinte 3 voices, 3 haut-
parleurs type à réflexion des
basses
Typ
: 3-Weg, 3-Lautsprecher-
Baßreflexbox
Lautsprecher
SP-MXKA3
Tieftöner
Mittenbereich
Hochtöner
SP-MXKA6
Tieftöner
Mittenbereich
Hochtöner
Haut-parleurs
SP-MXKA3
Médium
Graves
Aigus
SP-MXKA6
Médium
Graves
: 13,5 cm Konus × 1
: 5,0 cm Konus × 1
: 2,0 cm Aufgekelcht × 1
: conique de 13,5 cm × 1
: conique de 5,0 cm × 1
: dôme de 2,0 cm × 1
: 16,0 cm Konus × 1
: 5,0 cm Konus × 1
: 2,0 cm Aufgekelcht × 1
: conique de 16,0 cm × 1
: conique de 5,0 cm × 1
: dôme de 2,0 cm × 1
Aigus
Belastbarkeit:
SP-MXKA3
SP-MXKA6
Puissance maximale admissible
SP-MXKA3
SP-MXKA6
: 45 W
: 100 W
: 6 Ω
: 45 W
: 100 W
: 6 Ω
: 45 Hz–22 000 Hz
Impedanz
Impédance
Frequenzbereich
Schalldruckpegel
SP-MXKA3
SP-MXKA6
Abmessungen (B × H × T)
SP-MXKA3
SP-MXKA6
Gewicht
SP-MXKA3
SP-MXKA6
: 45 Hz bis 22 000 Hz
Bande passante
Pression sonore
SP-MXKA3
SP-MXKA6
Dimensions (L × H × P)
SP-MXKA3
SP-MXKA6
Masse
SP-MXKA3
SP-MXKA6
: 89 dB/W·m
: 87 dB/W·m
: 89 dB/W·m
: 87 dB/W·m
:228 mm × 316 mm × 258mm
:244 mm × 321 mm × 258mm
:228 mm × 316 mm × 258mm
:244 mm × 321 mm × 258mm
: Je 3,1 kg
: Je 3,6 kg
: 3,1 kg chaque
: 3,6 kg chaque
Présentation et caractéristiques modifiables sans préavis.
Technische Änderungen vorbehalten.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
AANSLUITINGEN
CONEXIÓN
• Gebruik GEEN andere versterker dan de CA-MXKA3/CA-
MXKA6 om dit luidsprekersysteem aan te sturen.
• NO utilice ningún otro amplificador para operar este sistema de
altavoces excepto CA-MXKA3/CA-MXKA6.
• Schakel de spanning van alle aangesloten komponenten uit
alvorens de luidsprekers met de versterker te verbinden.
• Desactive la alimentación de todo el sistema antes de conectar
los altavoces al amplificador.
• Het maximale vermogen van de SP-MXKA3 is 45 W en van de
SP-MXKA6 100 W. Te hoge ingang kan in abnormale
geluidsreproduktie en in beschadigingen resulteren.
Overbelasting en verbranding van de bedrading kan worden
veroorzaakt, wanneer de hieronder beschreven signalen naar
de luidspekers worden gevoed, zelfs wanneer de signalen onder
het maximaal toegestane ingangsvermogen zijn. Verminder
eerst het volume van de versterker.
• La capacidad máxima de potencia del SP-MXKA3 es de 45W,
y la del SP-MXKA6 es de 100W. Uná entrada excesiva resultará
en ruido anormal y posibles daños. En casos donde las señales
descritas más abajo se apliquen a los altavoces, aunque las
mismas resulten menores que la entrada máxima permisible,
pueden causar una sobrecarga y quemar el cableado de los
altavoces. Asegúrese de disminuir el volumen del amplificador
con anterioridad.
1) Ruis, zoals dit optreedtijdens afstemming op een FM-zender.
1) Ruido durante la sintonia en FM.
2) Hoogfrekwentie signalen van een hoog niveau, zoals die
tijdens het vooruitspoelen van een tapedeck worden
geproduceerd.
2) Señales de alto nivel que contengan componentes de alta
frecuencia producidos por un magnetófono en el modo de
avance rápido.
3) Klikkende geluiden, die worden veroorzaakt door het in - en
uitschakelen van de netspanning van andere komponenten.
3) Ruidos de conmutación provocados al encender y apagar
otros componentes.
4) Klikkende geluiden, zoals die worden geproduceerd bij het
tot stand brengen of verbreken van aansluitingen terwijl de
netspanning is ingeschakeld.
4) Ruido de conmutación al conectar o desconectar cables con
los componentes encendidos.
5) Ruido de conmutación cuando se reemplaza la cápsula con
los componentes encendidos.
5) Klikkende geluiden, zoals die optreden bij het vervangen van
het element van een draaitafel terwijl de netspanning is
ingeschakeld.
6) Ruido de conmutación provocados por la operación de los
selectores del amplificador.
6) Klikkende geluiden, zoals die worden geproduceerd door
bediening van de schakelaars van de versterker.
7) Voortdurende hoogfrekwentie-oscillatie, of hoogtonige,
7) Continua oscilación de alta frecuencia o de sonidos de tonos
altos provocados por instrumentos electrónicos.
8) Aullidos a utilizar micrófonos.
elektronisch
geproduceerde
geluiden
van
muziekinstrumenten.
8) Rondzingend geluid bij gebruik van mikrofoons.
ESPECIFICACIONES
TECHNISCHE GEGEVENS
Tipo
: Reflex bajo con 3-altavoces y 3 vias
Type
: 3-weg 3-luidsprekers bass reflex
Altavoces
SP-MXKA3
De subgraves
Principal
De agudos
SP-MXKA6
De subgraves
Principal
De agudos
Luidsprekers
SP-MXKA3
Woofer
: Tipo cónico de 13,5 cm × 1
: Tipo cónico de 5,0 cm × 1
: Tipo duomo de 2,0 cm × 1
: 13,5 cm kegeltype × 1
Midrange
Tweeter
: 5,0 cm kegeltype × 1
: 2,0 cm Kople × 1
SP-MXKA6
Woofer
: Tipo cónico de 16,0 cm × 1
: Tipo cónico de 5,0 cm × 1
: Tipo duomo de 2,0 cm × 1
: 16,0 cm kegeltype × 1
Midrange
Tweeter
Maximale vermogen
SP-MXKA3
: 5,0 cm kegeltype × 1
: 2,0 cm Kople × 1
Capacidad de potencia
SP-MXKA3
SP-MXKA6
: 45 W
: 100 W
: 6 Ω
: 45 Hz–22 000 Hz
: 45 W
SP-MXKA6
: 100 W
Impedancia
Impedantie
: 6 Ω
Gama de frecuencias
Nivel de presión acústica
SP-MXKA3
SP-MXKA6
Dimensiones (An × Al × Prf)
SP-MXKA3
SP-MXKA6
Peso
SP-MXKA3
SP-MXKA6
Frekwentiebereik
Geluidsdrukniveau
SP-MXKA3
: 45 Hz–22 000 Hz
: 89 dB/W·m
: 87 dB/W·m
: 89 dB/W·m
: 87 dB/W·m
SP-MXKA6
Afmetingen (B × H × D)
SP-MXKA3
SP-MXKA6
:228 mm × 316 mm × 258mm
:244 mm × 321 mm × 258mm
:228 mm × 316 mm × 258mm
:244 mm × 321 mm × 258mm
Gewicht
: 3,1 kg cada uno
: 3,6 kg cada uno
SP-MXKA3
SP-MXKA6
: Elk 3,1 kg
: Elk 3,6 kg
Veranderingen in technische gegevens et ontwerp onder
voorbehpoud.
El diseño y las especificaciones están sujetos a cambio sin aviso.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
COLLEGAMENTO
ANSLUTNING
• NON usare un amplificatore diverso dal modello CA-MXKA3/
CA-MXKA6 per utilizzare questo sistema di altoparlanti.
• Använd INTE någon annan förstärkare än CA-MXKA3/CA-
MXKA6 till att driva detta högtalarsystem med.
• Spegnete la corrente dell’intero sistema prima di collegare gli
altoparlanti all’amplificatore.
• Slå av strömmen i alla apparater i ljudanläggningen innan
högtalarna ansluts till förstärkaren.
• La potenza massima che può essere sopportata è 45 W nel
caso del modello SP-MXKA3 e 100 W nel caso del modello
SP-MXKA6. Un ingresso eccessivo causerà un suono anormale
è possibili danni. Nel caso in cui i segnali descriti qui sotto
vengono applicati agli altoparlanti, possono causare un
sovraccarico e bruciare il cablaggio degli altoparlanti, anche se
i segnali siano al di sotto dell’ingresso massimo ammesso.
Assicuratevi di diminuire il livello del volume dell’altoparlante
prima di procedere.
• Maximal effekthanteringskapacitet är 45 W för SP-MXKA3 och
100 W för SP-MXKA6. Brus uppstår i ljudet och högtalarna kan
skadas om de matas med för hög effekt. I situationerna som
beskrivs nedan kan högtalarna också överbelastas och
kabeltråden inne i hägtalarna brännas sönder, fastän
högtalarnas effekt inte har överskridits.
Sänk därför ljudstyrkan på förhand.
1) Brus under inställning av FM-radiostationer.
2) Starka, högfrekventa signaler från ett kassettdäck under
snabbspolning framåt.
1) Generazione di rumore durante la sintonizzazione FM.
2) Segnali di alto livello che contengono dei componenti ad alta
frequenza riprodotti da una piastra a cassette nel modo di
avanzamento rapido.
3) Ljudbangar som uppstår när andra apparater i anläggningen
slås till och från.
4) Skrapljud som uppstår när anslutningskablar ansluts eller
kopplas från medan strömmen är på.
3) Si senitrà uno scatto quando accendete o spegnete la corrente
degli altri compoenti.
5) Skrapljud som uppstår när pickupelementet på en skivspelare
byts medan strömmen är på.
4) Si sentirà uno scatto quando collegate o scollegate i cavi con
la corrente accesa.
6) Ljudbangar som uppstår när du använder förstärkarens
omkopplare.
5) Si sentirà uno scatto quando viene sostituita la cartuccia con
la corrente accesa.
7) Kontinuerliga, högfrekvenssvängningar eller högfrekvent ljud
från elektroniska musikinstrument.
6) Si sentirà uno scatto quando vengono usati gli interruttori
dell’amplificatore.
8) Akustisk återkoppling (tjutande ljud) vid bruk av mikrofoner.
7) Oscillazione continua ad alta frequenza o suoni acuti da
strumenti musicali elettronici.
8) Ululato quando usate i microfoni.
SPECIFICAZIONI
TEKNISKA DATA
Tipo
: Reflex basso con 3-altoparlanti e 3
vie
Typ
: 3-vägs, 3-elements
basreflexhögtalare
Altoparlanti
SP-MXKA3
Woofer
Midrange
Tweeter
SP-MXKA6
Woofer
Midrange
Högtalarelement
SP-MXKA3
Bas
: Cono da 13,5 cm × 1
: Cono da 5,0 cm × 1
: Cupola da 2,0 cm × 1
: 13,5 cm kon × 1
: 5,0 cm kon × 1
: 2,0 cm dome × 1
Mellanregisten
Diskantelement
SP-MXKA6
Bas
Mellanregisten
Diskantelement
Effekthanteringskapacitet
SP-MXKA3
: Cono da 16,5 cm × 1
: Cono da 5,0 cm × 1
: Cupola da 2,0 cm × 1
: 16,0 cm kon × 1
: 5,0 cm kon × 1
: 2,0 cm dome × 1
Tweeter
Capacità di potenza
SP-MXKA3
SP-MXKA6
: 45 W
: 100 W
: 45 W
: 100 W
SP-MXKA6
Impedenza
: 6 Ω
Impedans
: 6 Ω
Gamma di frequenza
Livello di pressione sonora
SP-MXKA3
SP-MXKA6
Dimensioni (L × A × P)
SP-MXKA3
SP-MXKA6
Massa
: 45 Hz–22 000 Hz
Frekvensomfång
Ljudtrycksnivå
SP-MXKA3
SP-MXKA6
Yttermått (B × H × D)
SP-MXKA3
SP-MXKA6
Vikt
: 45 Hz–22 000 Hz
: 89 dB/W·m
: 87 dB/W·m
: 89 dB/W·m
: 87 dB/W·m
: 228 mm × 316 mm × 258mm
: 244 mm × 321 mm × 258mm
:228 mm × 316 mm × 258mm
:244 mm × 321 mm × 258mm
SP-MXKA3
SP-MXKA6
: 3,1 kg ciascuno
: 3,6 kg ciascuno
SP-MXKA3
SP-MXKA6
: 3,1kg perst.
: 3,6kg perst.
Il disegno e le specificazioni sono soggetti a cambiamenti senza
preavviso.
Rätt till ändringar av utförande och specifikationer förbehålles utan
föregående meddelande.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TILSLUTNING
LIITÄNTÄ
• Anvend IKKE anden forstærker end CA-MXKA3/CA-MXKA6 til
drift af dette højttalersystem.
• ÄLÄ käytä muuta vahvistinta tämän kaiutinjärjestelmän käyttöön
paitsi mallille CA-MXKA3/CA-MXKA6.
• Sluk for strømmen til hele systemet før højttalerne forbindes til
forstærkeren.
• Katkaise koko järjestelmän virta ennen kuin suoritat liitännät
kaiuttimista vahvistimeen.
• Den maksimale effektbehandlingskapacitet for SP-MXKA3 er
45 W, og 100 W for SP-MXKA6. For kraftigt indgangssignal vil
resultere i unormal stoj og muligvis beskadigelse. I tilfælde hvor
højttalerne udsættes for signalerne beskrevet nedenfor, kan der
forekomme overbelastning og overbrænding af ledningerne i
höjttalerne selv om signalstyrken er under den maksimale tilladte
værdi. Husk derfor at at sænke højttalerlydstyrken i forvejen.
• Mallin SP-MXKA3 suurin tehonkäsittelykyky on 45 W, mallin
SP-MXKA6 100 W. Liiallinen antoteho aiheuttaa epänormaalia
kohinaa ja jopa vahinkoa. Tapauksissa, missä kaiuttimet joutuvat
alla kuvattujen signaalien kohteeksi, vaikka signaalit olisivat alle
sallitun maksimi antotehon, ne saattavat aiheuttaa ylikuormitusta
ja polttaa kaiuttimien johdot. Vähennä siis vahvistimen
äänenvoimakkuutta jo ennalta.
1) Støj under FM-afstemning.
1) Kohinaa FM-virityksen aikana.
2) Signaler med høje niveauer der indeholder höjfrekvente
komponenter dannet af en båndoptager der er indstillet til
hurtig fremspoling.
2) Kasettidekistä eteenpäinkelauksen aikana muodostuneet
vahvat, korkeataajuuksisia komponentteja sisältävät signaalit.
3) Klik-ääni, joka syntyy silloin kun toisten osien virta kytketään
ja katkaistaan.
3) Klikstøj dannet når der tændes eller slukkes for strommen til
andre domponenter.
4) Klik-ääni, joka syntyy silloin kun kytketään tai irrotetaan johtoja
virran ollessa päällä.
4) Klikstøj der dannes når ledninger tilsluttes eller tages ud af
forbindelse mens der er tændt for strømmen.
5) Klikstøj der dannes når pickuppen udskiftes mens der er tændt
for strømmen.
5) Klik-ääni, joka syntyy silloin kun vaihdetaan hylsy virran ollessa
päällä.
6) Klik-ääni, joka syntyy silloin kun käytetään vahvistimen
kytkimiä.
6) Klikstøj der dannes når forstærkerens omskiftere betjenes.
7) Fortsat høj frekvenssvingning, eller en højlyd dannet af et
elektronisk instrument.
7) Jatkuva korkea värähtely tai elektronisesti tuotettu korkea
soittimen ääni.
8) Hyletoner når der anvendes en mikrofon.
8) Ulinaa mikrofonia käytettäessä.
TEKNISET TIEDOT
SPECIFIKATIONER
Tyyppi
: 3-tie, 3 kaiuttimen bassorefleksi
Type
: 3-vejs basrefleks-højttaler
med 3-elementer
Kaiuttimet
Højttalere
SP-MXKA3
Basso
Keskikaiutin
Diskantti
SP-MXKA6
Basso
Keskikaiutin
Diskantti
SP-MXKA3
Bashøjttaler
Mellemtonehøjttaler
Diskantenhed
SP-MXKA6
Bashøjttaler
Mellemtonehøjttaler
Diskantenhed
Belastningskapacitet
SP-MXKA3
SP-MXKA6
Impedans
Frekvensområde
Lydtryksniveau
SP-MXKA3
SP-MXKA6
Mål (B × H × D)
SP-MXKA3
SP-MXKA6
Vægt
: 13,5 cm karitomuotoinen × 1
: 5,0 cm karitomuotoinen × 1
: 2,0 cm holvi × 1
: 13,5 cm membran × 1
: 5,0 cm membran × 1
: 2,0 cm dome × 1
: 16,0 cm karitomuotoinen × 1
: 5,0 cm karitomuotoinen × 1
: 2,0 cm holvi × 1
: 16,0 cm membran × 1
: 5,0 cm membran × 1
: 2,0 cm dome × 1
Enimmäisteho
SP-MXKA3
SP-MXKA6
: 45 W
: 100 W
: 6 Ω
: 45 Hz–22 000 Hz
: 45 W
: 100 W
: 6 Ω
: 45 Hz–22 000 Hz
Impedanssi
Taajuusala
Äänenpainetaso
SP-MXKA3
SP-MXKA6
Mitat (L × K × S)
SP-MXKA3
SP-MXKA6
Paino
: 89 dB/W·m
: 87 dB/W·m
: 89 dB/W·m
: 87 dB/W·m
: 228 mm × 316mm × 258mm
:244 mm × 321mm × 258mm
:228 mm × 316mm × 258mm
:244 mm × 321mm × 258mm
SP-MXKA3
SP-MXKA6
: 3,1 kg perst.
: 3,6 kg perst.
SP-MXKA3
SP-MXKA6
: 3,1 kg hver
: 3,6 kg hver
Oikeudet muutoksiin pidätetään.
Design og specifikationer kan blive ændret uden varsel.
EN. GE. FR. NL. SP. IT. SW. DA. FI.
XXXXX
0203NSMMACBET
VICTOR COMPANY OF JAPAN, LIMITED
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|