MICRO COMPONENT SYSTEM
UX-J60—Consists of CA-UXJ60 and SP-UXJ60
UX-J50—Consists of CA-UXJ50 and SP-UXJ50
RM-SUXJ60U REMOTE CONTROL
SP-UXJ60
CA-UXJ60
SP-UXJ60
RM-SUXJ50U REMOTE CONTROL
SP-UXJ50
CA-UXJ50
SP-UXJ50
For Customer Use:
INSTRUCTIONS
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0102-005B
[A]
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT FOR LASER PRODUCTS
REPRODUCTION OF LABELS
1
CLASSIFICATION LABEL ON EXTERIOR SURFACE
2
WARNING LABEL INSIDE THE UNIT
ADVARSEL: Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgå udsæt-
VARO: Avattaessa ja suo-
CAUTION: Invisible laser
radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE
VARNING: Osynlig laser-
strålning när denna del är
öppnad och spärren är
jalukitus ohitettaessa olet
alttiina
näkymättömälle
lasersäteilylle. Älä katso
urkopplad.
Betrakta
ej
(s)
telse for stråling
(d)
säteeseen.
(f)
TO BEAM.
(e)
strålen.
1. CLASS 1 LASER PRODUCT
2. CAUTION: Invisible laser radiation when open and interlock failed
or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to qualified
service personnel.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1
2
3
Front:
No obstructions and open spacing.
Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
Bottom:
Place on a level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Front view
Side view
15 cm
1 cm
15 cm
1 cm
15 cm
15 cm
15 cm
UX-J60
UX-J50
10 cm
UX-J60/UX-J50
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
Power sources
• When unplugging the unit from the wall outlet, always pull
on the plug, not the AC power cord.
About This Manual
This manual is organized as follows:
• The manual mainly explains operations using the
buttons on the remote control.
You can use the buttons both on the remote control and
on the main unit for the same operations if they have
the same or similar names (or marks), unless mentioned
otherwise.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lens inside the unit in the
following cases:
The illustrations used in this manual are of UX-J60
unless mentioned otherwise.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated for
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Common Operations” on pages 9
to 11.
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should condensation occur, the unit may malfunction. In this
case, leave the unit turned on for a few hours until the
moisture evaporates, unplug the AC power cord, then plug it
in again.
• The following symbols are used in this manual:
Gives you warning and caution to prevent
damage or risk of fire/electric shock.
Furthermore, it gives you information about
what is not good for obtaining the best possible
performance from the unit.
Others
• Should any metallic object or liquid fall into the unit,
unplug the power cord and consult your dealer before
operating any further.
• If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
Gives you information and hints you should
know.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
• Install the unit in a location with adequate ventilation to
prevent internal heat buildup in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Location of the Buttons and Control ..................................... 3
Front Panel ........................................................................................... 3
Remote Control .................................................................................... 5
Getting Started ........................................................................ 6
Supplied Accessories............................................................................ 6
Putting the Batteries into the Remote Control ..................................... 6
Connecting Antennas ........................................................................... 6
Connecting Speakers ............................................................................ 7
Connecting Other Equipment............................................................... 8
Common Operations ............................................................... 9
Setting the Clock .................................................................................. 9
Turning On the Power .......................................................................... 9
Adjusting the Volume ......................................................................... 10
Enjoying Sound Effects...................................................................... 10
Selecting the Illumination Brightness ................................................ 11
Selecting the Display Color (ONLY FOR UX-J60)........................... 11
Listening to FM and AM Broadcasts................................... 12
Tuning in to a Station ......................................................................... 12
Presetting Stations .............................................................................. 12
Tuning in to a Preset Station .............................................................. 13
Playing Back Discs ................................................................ 14
Playing Back the Entire Disc—Normal Play ..................................... 14
Basic Disc Operations ........................................................................ 15
Programming the Playing Order of the Tracks—Program Play......... 15
Playing at Random—Random Play ................................................... 16
Repeating Tracks—Repeat Play......................................................... 16
Prohibiting Disc Ejection—Tray Lock .............................................. 16
Playing Back Tapes................................................................ 17
Playing Back a Tape ........................................................................... 17
Recording ............................................................................... 18
Recording on a Tape ........................................................................... 18
Disc Direct Recording ........................................................................ 19
One Track Recording ......................................................................... 19
Using the Timers .................................................................... 20
Using Daily Timer and Recording Timer ........................................... 20
Using Sleep Timer .............................................................................. 21
Maintenance........................................................................... 22
Troubleshooting ..................................................................... 23
Specifications ......................................................................... 24
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of the Buttons and Control
Become familiar with the buttons and control on your unit.
Front Panel
Front Panel
1
2
FOR UX-J50:
w
e
3
4
5
r
t
FOR UX-J50:
6
7
y
u
8
9
i
MICRO COMPONENT SYSTEM
UX-J60
p
q
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Continued
Display Window
1
2
3
4
[
]
DAILY REC SLEEP REC
ST
SURROUND
BASS
MONO
PRGM
RANDOM
ALL
AHB
5
6
7
8
9
p
See the pages in parentheses for details.
Front Panel
1 Disc tray
Display Window
1 Timer indicators
2 Display window
•
(timer), DAILY, REC (recording timer), and SLEEP
3 REV.MODE (reverse mode) button (17 – 19)
4 AUX button (9)
2 REC (recording) indicator
3 ONLY FOR UX-J60:
Pressing this button also turns on the unit.
SURROUND indicator
4 ONLY FOR UX-J60:
5 STANDBY/ON
button and STANDBY/ON lamp
BASS indicator
(9, 21)
5 Disc play mode indicators
• PRGM (program), RANDOM, and
6 ST (stereo) indicator
6 REC (recording) button (18, 19)
7 Multi operation buttons
ALL (repeat)
• DOWN/4 (reverse skip), 7 (stop)
and ¢ (forward skip)/UP
8 CD ‹/8 (play/pause) button (9, 14 – 16)
Pressing this button also turns on the unit.
9 TAPE ¤ ‹ button (9, 17)
Pressing this button also turns on the unit.
p Cassette holder
7 Main display
• Shows the source name, frequency, etc.
8 AHB (Active Hyper Bass pro) indicator
9 Tape operation indicators
• 2 3 (tape direction) and
p MONO indicator
(reverse mode)
q PHONES jack (10)
w FOR UX-J60:
COLOR button (11)
FOR UX-J50:
CLOCK/TIMER button (9, 20, 21)
e CD 0 (disc tray open/close) button (14)
Pressing this button also turns on the unit.
r VOLUME + / – control (10)
t FOR UX-J60:
SOUND TURBO button (11)
SURROUND button (11)
AHB (Active Hyper Bass) PRO button (10)
FOR UX-J50:
AHB (Active Hyper Bass) PRO button (10)
BASS button (10)
TREBLE button (10)
y Remote sensor
u FM/AM button (9, 12, 13)
Pressing this button also turns on the unit.
i PUSH OPEN 0 (cassette holder open) portion (17 – 19)
When using the remote control, point it at the
remote sensor on the front panel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
See the pages in parentheses for details.
1 Number buttons
2 BASS button (10)
3 Multi operation buttons
STANDBY/ON
DISPLAY
• UP, 4 (reverse skip), 7 (stop), ¢ (forward skip),
and DOWN
4 SET button (15)
1
4
7
2
5
8
3
6
8
9
p
q
w
5 Source buttons
1
CLOCK
/TIMER
• CD 3/8, TAPE 2 3, FM/AM, and AUX
Pressing one of these buttons also turns on the unit.
6 CD 0 (disc tray open/close) button (14)
Pressing this button also turns on the unit.
7 REV.MODE (reverse mode) button (17 – 19)
9
SLEEP
10
BASS
+10
UP
TREBLE
2
3
8 STANDBY/ON
button (10, 21)
9 DISPLAY button (9)
p CLOCK/TIMER button (9, 20, 21)
q SLEEP button (21)
w TREBLE button (10)
e CANCEL button (16)
SET
CANCEL
DOWN
4
5
e
CD
TAPE FM/AM AUX
REV.
r
t
y
CD
MODE
FM MODE COLOR
r FM MODE button (12)
t ONLY FOR UX-J60:
6
7
PRGM
RANDOM REPEAT
AHB
COLOR button (11)
SOUND
TURBO
PRO
y Disc play mode buttons (15, 16)
• PRGM (program), RANDOM, and REPEAT
u ONLY FOR UX-J60:
SURROUND
u
i
SOUND TURBO button (11)
SURROUND button (11)
i AHB (Active Hyper Bass) PRO button (10)
o VOLUME + / – button (10)
; DIMMER button (9, 11)
o
;
DIMMER
VOLUME
RM-SUXJ60U REMOTE CONTROL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Continued
Supplied Accessories
Connecting Antennas
Make sure that you have all the following items.
The number in parentheses indicates the quantity of each
piece supplied.
FM antenna
ANTENNA
• AM loop antenna (1)
• FM antenna (1)
• Remote control (1)
FM antenna (supplied)
EXT
M LOOP
FM 75
COAXIAL
• Batteries (2)
• Speaker cords (ONLY FOR UX-J60) (4)
If anything is missing, consult your dealer immediately.
Putting the Batteries into the Remote Control
1 Attach the FM antenna to the FM 75 Ω
Insert the batteries—R6(SUM-3)/AA(15F)—into the
remote control, by matching the polarity (+ and –) on the
batteries with the + and – markings on the battery
compartment.
COAXIAL terminal.
2 Extend the FM antenna.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
3 Fasten it up in the position which gives you
the best reception, then fix it on the wall,
etc.
1
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary
measure. If reception is poor, you can connect an outdoor FM
antenna.
R6(SUM-3)/AA(15F)
To connect an outdoor FM antenna
Before connecting the antenna, disconnect the supplied FM
antenna.
2
Outdoor FM antenna
(not supplied)
3
Coaxial cable (not supplied)
ANTENNA
EXT
M LOOP
FM 75
COAXIAL
• DO NOT use an old battery together with a new
one.
• DO NOT use different types of batteries together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery
compartment when you are not going to use the
remote control for an extended period of time.
Otherwise, the remote control will be damaged
from battery leakage.
A 75 Ω antenna with coaxial type connector
(IEC or DIN 45325) should be used.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
AM antenna
Connecting Speakers
1
2
FOR UX-J60:
1
ANTENNA
Vinyl-covered wire
(not supplied)
EXT
AM LOOP
2
3
FM 75
COAXIAL
3
Gray
RIGHT
RIGHT
LEFT
LEFT
Red
Speaker
cord
AM loop antenna
(supplied)
Speaker
cord
MAIN SPEAKERS
SUBWOOFERS
CAUTION: SPEAKER MDANCE
6
-16
Black
Blue
1 If the cords are covered with insulation,
remove a short section of insulation at the
end of each cord by twisting and pulling it
off.
2 Connect the AM loop antenna to the AM
LOOP terminals as illustrated.
INPUT
INPUT
INPUT
INPUT
3 Turn the AM loop antenna until you have
the best reception.
Right speaker
Left speaker
To connect an outdoor AM antenna
When reception is poor, connect a single vinyl-covered wire
to the AM EXT terminal and extend it horizontally. The AM
loop antenna must remain connected.
FOR UX-J50:
SPEAKERS
RIGHT
LEFT
Speaker cord
For better reception of both FM and AM
• Make sure the antenna conductors do not touch any other
terminals and connecting cords.
Speaker cord
SPEAKER
IMPEDANCE
6
- 16
• Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.
Right speaker
Left speaker
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1 If the cords are covered with insulation,
remove a short section of insulation at the
end of each cord by twisting and pulling it
off.
Connecting Other Equipment
To connect an audio equipment
You can connect audio equipment—used only as a playback
device.
2 Press and hold the clamp of the speaker
• DO NOT connect any equipment while the power
is on.
terminal as illustrated.
• DO NOT plug in any equipment until all
connections are complete.
3 Insert the end of the speaker cord into the
terminal.
Match the polarity between the unit and the speaker
terminals: ª to ª and · to ·.
Be sure that the plugs of the audio cords are colored: White
plugs and jacks are for left audio signals, and red ones for
right audio signals.
4 Release your finger from the clamp.
R
L
AUX
R
L
• DO NOT connect speakers while the power is on.
• DO NOT connect more than one speaker to each
speaker teminal.
IMPORTANT: Use only speakers with the same speaker
impedance as shown on the speaker terminals on the
rear of the unit.
To audio output
L
Audio equipment
R
For playing other equipment through this unit, connect
between the audio output jacks on the other equipment and
AUX jacks by using audio cords (not supplied).
To remove the speaker grilles
The speaker grilles are removable.
Holes
Now, you are ready to plug in the unit
and any other connected equipment.
Projections
IMPORTANT: Be sure to check all connections to be
done before plugging the AC power cord into a wall outlet.
Speaker grille
To remove the speaker grille, insert your fingers at the top
of the speaker grille, pull towards you. Then pull the bottom
towards you.
To attach the speaker grille, put the projections of the
speaker grille into the holes of the speaker.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Operations
To change the clock
Setting the Clock
1
Make sure the (timer) indicator is not lit on the
Before operating the unit any further, first set the unit’s clock.
When you plug the AC power cord into the wall outlet,
“0:00” starts flashing on the display.
display.
• If it is lit, press and hold CLOCK/TIMER until it goes
off.
You can set the clock whether the unit is on or off.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step 1.
• For UX-J50 only, you can also use CLOCK/TIMER on the
unit for this operation.
2
Press CLOCK/TIMER repeatedly until the unit enters
the clock setting mode (the hour digits start flashing
on the display).
First time you press CLOCK/TIMER, the unit enters the
timer setting mode. (See page 20.)
3
4
Repeat steps 2 and 3 of the procedure of “Setting the
Clock.”
CLOCK
1 Press CLOCK/TIMER.
/TIMER
The hour digits start flashing on the display.
Press and hold CLOCK/TIMER again so that the
(timer) indicator goes off.
UP
Turning On the Power
2 Press UP or DOWN to
CLOCK
adjust the hour, then
/TIMER
STANDBY/ON
press CLOCK/TIMER.
The minute digits start flashing.
To turn on the unit, press
DOWN
STANDBY/ON
.
The STANDBY/ON lamp lights
green and “HELLO” appears on
the display.
• When you press the source button—CD 3/8, TAPE 2 3,
FM/AM, and AUX, the unit automatically turns on and
starts playback if the source is ready.
3 Press UP or DOWN to adjust the minute,
then press CLOCK/TIMER.
To turn off the unit (standby), press STANDBY/ON
again.
The STANDBY/ON lamp lights red and “GOOD BYE”
appears on the display.
• “0:00” flashes on the display until you set the built-in
clock. After setting the clock, the clock time will appear on
the display while the unit is on standby.
To check the clock time during play
On the remote control ONLY:
The illumination and display brighten only for 4 seconds
by pressing DIMMER.
DISPLAY
Press DISPLAY (gray-colored).
• Each time you press the button, the source
indication and the clock time alternate on the
display.
• A little power is always consumed even while the unit is on
standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
The clock is reset to “0:00” right away, while the tuner preset
stations (see page 12) will be erased in a few days.
• When you unplug the AC power cord or if a power failure
occurs
The clock is reset to “0:00” right away. If this happens, set the
clock again.
• The clock may gain or lose 1 to 2 minutes per month
If this happens, reset the clock.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Continued
Adjusting the Volume
Enjoying Sound Effects
You can adjust the volume level only while the unit is turned
on. The volume level can be adjusted between “VOL MIN”
and “VOLUME 1” – “VOLUME 40 (VOL MAX).”
You can adjust the sound by using various sound effect
functions.
• These functions only affect the playback sound, and do not
affect your recording.
On the remote control:
Press VOLUME + to increase the volume or
press VOLUME – to decrease it.
To adjust the tone (Bass/Treble)
You can adjust the bass level (low frequency range) and the
treble level (high frequency range) within a range of –5 to +5.
When shipped, the bass level set to “BASS +2” and the treble
level set to “TREBLE +2.”
VOLUME
On the unit:
Turn VOLUME + / – control clockwise
(+) to increase the volume or
counterclockwise (–) to decrease it.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step 1.
• For UX-J50 only, you can also use BASS and TREBLE on
the unit for this operation.
For private listening
BASS
TREBLE
1 Press BASS to adjust the
bass level or press TREBLE
to adjust the treble level.
Connect headphones to the PHONES jack. No sound comes out of
the speakers. Be sure to turn down the volume before connecting or
putting on headphones.
• Each timer you press the button,
DO NOT turn the unit off (standby) with the volume
set to an extremely high level; otherwise, the
sudden blast of sound can damage your hearing,
speakers and/or headphones when you turn on the
unit or start playing any source next time.
REMEMBER you cannot adjust the volume level
while the unit is on standby.
“BASS” and “TREBLE” appears in the display
alternately.
UP
2 Press UP to increase the level
or press DOWN to decrease it.
DOWN
To reinforce the bass sound
You can reinforce the bass sound to maintain rich, full bass at
low volume—Active Hyper Bass Pro.
For UX-J60:
AHB
Press AHB PRO.
PRO
• Each time you press the button, the Active
Hyper Bass Pro is turned on (AHB ON) and
off (AHB OFF) alternately. When it is turned
on, the AHB indicator lights up on the display.
AHB
For UX-J50:
AHB
Press AHB PRO until “AHB 1” or “AHB 2”
PRO
appears on the display.
The AHB indicator also lights up on the display.
• Each time you press the button, the bass
reinforcement changes as follows:
AHB 1
AHB 2
AHB OFF
(Canceled)
• “AHB 2” has much more bass reinforcement effect than
“AHB 1.”
To cancel the effect, press AHB PRO until “AHB OFF”
appears on the display and the AHB indicator goes off.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To enjoy the heavy sound (ONLY FOR UX-J60)
You can enjoy the heavy sound. The function boosts low and
high frequency sounds—Sound Turbo.
Selecting the Display Color (ONLY FOR UX-J60)
You can select the display color (COLOR 1 – COLOR 5 and
AUTO mode).
SOUND
Press SOUND TURBO.
TURBO
• AUTO mode changes the color (COLOR 1 to COLOR 5)
gradually.
• Each time you press the button, the Sound
Turbo is turned on and off alternately. When it
is turned on, the BASS indicator lights up on
the display.
COLOR
To select the color, press COLOR.
• Each time you press the button, the color
changes as follows:
BASS
AUTO
COLOR 1
COLOR 4
COLOR 2
COLOR 3
COLOR 5
When the Sound Turbo is on, the bass and the treble levels
are set to +2 (see page 10). After the Sound Turbo is
canceled, these levels restored to the previous levels.
To reinforce the surround effect (ONLY FOR UX-J60)
You can reinforce the surround effect.
• This function does not affect your recording and playback
sound of monaural sources.
SURROUND
To get the effect, press SURROUND so that
the SURROUND indicator lights up on the
display.
To cancel the effect, press SURROUND again so that the
SURROUND indicator goes off.
Selecting the Illumination Brightness
You can change the illumination and display brightness only
while the unit is turned on.
On the remote control ONLY:
DIMMER
To change the brightness, press DIMMER.
• Each time you press the button, the illumination
and display dim (DIM ON) and brighten (DIM
OFF) alternately.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to FM and AM Broadcasts
Continued
Tuning in to a Station
Presetting Stations
You can preset 30 FM and 15 AM stations.
In some cases, test frequencies have been already memorized
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction.
You need to preset stations separately for the FM and AM
bands.
FM/AM
1 Press FM/AM to select the band.
The unit automatically turns on and tunes in
to the previously received station—either FM
or AM.
• Each time you press the button, the band alternates
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step 2.
between FM and AM.
On the remote control ONLY:
1 Tune in to the station you want to preset.
2 Press and hold ¢ or 4
for more than 1 second.
• See “Tuning in to a Station.”
The unit starts searching for
SET
2 Press SET.
stations and stops when a station of sufficient signal
strength is tuned in.
• If a program is broadcast in stereo, the ST (stereo)
indicator lights up.
UP
To stop searching, press ¢ or 4.
3 Press UP or DOWN to select a
preset number.
DOWN
When you press ¢ or 4 briefly and repeatedly
The frequency changes step by step.
To change the FM reception mode
4 Press SET again.
On the remote control ONLY:
FM MODE
When an FM stereo broadcast is hard to
receive or noisy, press FM MODE so that the
MONO indicator lights up on the display.
Reception will improve.
The tuned station in step 1 is stored in the preset number
selected in step 3.
• Storing a new station on a used number erases the
To restore the stereo effect, press FM MODE again so that
the MONO indicator goes off. In stereo mode, you can hear
stereo sound when a stereo program is broadcast.
previously stored one.
When you unplug the AC power cord or if a power
failure occurs
The tuner preset stations will be erased in a few days. If this
happens, preset the stations again.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning in to a Preset Station
On the remote control ONLY:
FM/AM
1 Press FM/AM to select the band.
The unit automatically turns on and tunes in
to the previously received station—either FM
or AM.
• Each time you press the button, the band alternates
between FM and AM.
UP
2 Press UP or DOWN to select a
preset number.
DOWN
To tune in to a preset station directly using the number
buttons
On the remote control ONLY:
Pressing the number button(s) allows you to select the preset
number you want.
Ex.: For preset number 5, press 5.
For preset number 15, press +10,
then 5.
1
2
5
8
3
4
6
For preset number 20, press +10,
then 10.
For preset number 30, press +10,
+10, then 10.
7
9
10
+10
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Discs
Continued
This unit has been designed to play back the following discs
—CD, CD-R, and CD-RW.
Playing Back the Entire Disc—Normal Play
CD
When playing a CD-R or CD-RW
1 Press CD 0.
User-edited CD-Rs (CD-Recordable) and CD-RWs
(CD-ReWritable) can be played only if they are already
“finalized.”
The unit automatically turns on and the disc
tray comes out.
• Usually you can play back your original CD-Rs or CD-
RWs recorded in music CD format. However, sometimes
they may not play depending on their characteristics or
recording conditions.
2 Place a disc correctly on the circle of the
disc tray, with its label side up.
• Before playing CD-Rs or CD-RWs, read their instructions
or cautions carefully.
• Some CD-Rs or CD-RWs may not play on this unit because
of their disc characteristics, damage or stain on them, or if
the player’s lens is dirty.
• CD-RWs may require a longer readout time. This is
because the reflectance of CD-RWs is lower than for
regular discs.
CORRECT
INCORRECT
• When using a CD single (8 cm), place it on the inner
circle of the disc tray.
CD
3 Press CD 3/8.
The disc tray automatically closes and the first
track of the disc starts playing.
General notes
In general, you will have the best performance by keeping
your discs and the mechanism clean.
• Store discs in their cases, and keep them in cabinets or on
shelves.
Track number
Elapsed playing time
• Keep the unit’s disc tray closed when not in use.
• The disc automatically stops when the last track has
finished playing.
Continued use of irregular shape discs
(heart-shape, octagonal, etc.) can damage the unit.
To stop playing, press 7.
BASS
Handling discs
• Remove the disc from its case by
holding it at the edge while pressing the
center hole lightly.
Total track number
Total playing time
• Do not touch the shiny surface of the
disc, or bend the disc.
To remove the disc, press CD 0.
• Put the disc back in its case after use to
prevent warping.
• Be careful not to scratch the surface
of the disc when placing it back in its
case.
• Avoid exposure to direct sunlight,
temperature extremes, and moisture.
• If the disc cannot be read correctly (because it is scratched,
for example) or an unreadable CD-R or CD-RW is inserted
Playback will not start.
• If no disc is inserted
“NO DISC” appears on the display.
• If the loaded disc has more than 21 tracks and you select 21st
track or above
To clean the disc
Wipe the disc with a soft cloth in a
straight line from center to edge.
“– –:– –” appears on the display instead of the playing time.
DO NOT try to open or close the disc tray by hand
as it will be damaged.
DO NOT use any solvent—such as conventional record
cleaner, spray, thinner, or benzine—to clean the disc.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PRGM
Basic Disc Operations
2 Press PRGM (program).
The PRGM (program) indicator lights up on
the display.
While playing a disc, you can do the following operations.
To stop playing for a moment
During play, press CD 3/8.
ST
PRGM
CD
While pausing, the elapsed playing time flashes on
the display.
• If a program has been stored in memory, the program
is called up.
To resume playing, press CD 3/8 again.
UP
3 Press UP or DOWN to select the
track number, then press SET.
To go to another track
• You can select the track number directly
DOWN
Before or during play, press ¢ or
4 repeatedly.
using the number button(s). (See “To go
to another track directly using the
number buttons.”)
• ¢ : Skips to the beginning of the
next or succeeding tracks.
SET
ST
• 4 : Goes back to the beginning of the current or
previous tracks.
PRGM
Track number
Program step number
To go to another track directly using the number
buttons
On the remote control ONLY:
4 Repeat step 3 to program other tracks you
want.
Pressing the number button(s) before or during play allows
you to start playing the track number you want.
Ex.: For track number 5, press 5.
CD
5 Press CD 3/8.
The tracks are played in the order you have
programed.
1
4
2
5
8
3
6
For track number 15, press +10,
then 5.
For track number 20, press +10,
then 10.
For track number 32, press +10,
+10, +10, then 2.
7
9
If you try to program a 21st track
“FULL” will appear on the display.
10
+10
To stop playing, press 7.
To locate a particular point in a track
During play, press and hold ¢ or
4.
• ¢ : Fast-forwards the tracks.
• 4 : Fast-reverses the tracks.
PRGM
To exit from Program Play, press PRGM
(program) before or after playing.
• The PRGM (program) indicator goes off.
• The Program remains even when you select
another play mode (Normal or Random Play).
Play mode setting (Normal, Program, and Random
Play) will not change even if you do the following
operations;
Programming the Playing Order of the Tracks
—Program Play
• Changing the source—selecting the CD player as the source
restores the previous play mode.
• Turning off the unit—turning on the unit restores the previous
play mode.
You can arrange the order in which tracks play before you
start playing. You can program up to 20 tracks.
On the remote control ONLY:
1 Load a disc.
To check the program contents
You can check the program contents
by pressing ¢ or 4 before or
after playback.
• If the current playing source is not the CD player,
press CD 3/8, then 7 before going to the next step.
• ¢ : To check the contents in the
programmed order.
• 4 : To check the contents in the reverse order.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To modify the program
On the remote control ONLY:
Repeating Tracks—Repeat Play
You can have all the tracks, the program or individual track
currently playing, repeat as many times as you like.
CANCEL
Before or after playing, you can erase the last
programed track by pressing CANCEL.
• Each time you press the button, the last
programed track is erased from the program.
On the remote control ONLY:
REPEAT
To repeat playing, press REPEAT before or
To add tracks in the program before playing, simply select
the track numbers you want to add by following step 3 of the
programming procedure.
during play.
• Each time you press the button, Repeat Play
changes as follows, and the following repeat
indicator lights up on the display:
To erase the program, press 7 before or after
playing.
• Disc ejection also erases the program.
ALL
Canceled
:
Repeats one track.
ALL : In Normal Play, repeats all the tracks.
In Program Play, repeats all the tracks in the
program.
Playing at Random—Random Play
In Random Play, repeats all the tracks in
random order.
The tracks will play in no particular order when you use this
mode.
On the remote control ONLY:
To cancel Repeat Play, press REPEAT repeatedly until the
repeat indicator goes off.
• Repeat Play remains in effect even when you select another
play mode (Normal, Program or Random Play).
1 Load a disc.
• If the current playing source is not the CD player,
press CD 3/8, then 7 before going to the next step.
• In Random Play,
selected when you press RANDOM, it is canceled.
cannot be selected. If
has been
RANDOM
2 Press RANDOM.
The RANDOM indicator lights up on the
display.
CD
Prohibiting Disc Ejection—Tray Lock
3 Press CD 3/8.
The tracks are randomly played.
Random Play ends when all the tracks are
played once.
You can lock the disc tray and prohibit ejecting the disc
whether the unit is on or off.
On the unit ONLY:
To skip the current track, press ¢.
• You cannot go back to the previous track by
pressing 4.
To prohibit disc ejection, press CD ‹/8
while holding 7.
• If the disc tray is opened, close it first.
To stop playing, press 7.
+
To exit from Random Play, press RANDOM before or after
playing.
Random Play is canceled and Normal Play resumes.
• The RANDOM indicator goes off.
To cancel the prohibition and unlock the
disc, press CD ‹/8 while holding 7.
Play mode setting (Normal, Program, and Random
Play) will not change even if you do the following
operations;
• Changing the source—selecting the CD player as the source
restores the previous play mode.
• Turning off the unit—turning on the unit restores the previous
play mode.
If you try to eject the disc while Tray Lock is in use
“LOCKED” appears to inform you that the disc tray is locked.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Tapes
You can play back type I tapes.
To stop playing, press 7.
Playing Back a Tape
To fast-wind to the left or to the
right, press ¢ or 4 while the
tape is not running.
The tape direction indicator (3 or 2)
starts flashing rapidly on the display.
1 Press PUSH OPEN 0 on the unit.
PUSH OPEN
To remove the cassette, press PUSH OPEN 0 on the unit.
• If the tape is playing, stop it first.
To play both sides—Reverse Mode
You can set the deck to play just one side of a tape, both sides
once, or both sides continuously.
REV.
Press REV.MODE (reverse mode).
• Each time you press the button, the Reverse
Mode changes as follows:
2 Put a cassette in with the exposed part of
MODE
the tape down.
: The deck automatically stops after playing both
sides of the tape. Stops when playback in the 2
direction is finished.
: The deck continues to play both sides of the tape
until 7 is pressed.
3 Press PUSH OPEN 0 again to close the
: The deck automatically stops after playing one
side of the tape.
cassette holder.
• DO NOT open the cassette holder when the tape
is running.
• The use of C-120 or thinner tape is not
recommended, since characteristic deterioration
may occur and this tape easily jams in the pinch-
rollers and the capstans.
TAPE
4 Press TAPE 2 3.
The unit automatically turns on and the
tape starts playing. The tape direction
indicator (3 or 2) flashes slowly on the
display.
• Each time you press the button, the tape direction
changes:
3 : plays the front side.
2 : plays the reverse side.
When the tape plays to the end, the deck automatically
stops if the Reverse Mode is set to
or
. (See
“To play both sides—Reverse Mode.”)
If no cassette is inserted when you press TAPE 2 3
“NO TAPE” appears on the display.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Continued
IMPORTANT:
Recording on a Tape
• It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
• The recording level is automatically set correctly, so it is
not affected by the other sound settings. Thus, during
recording you can adjust the sound you are actually
listening to without affecting the recording level.
• If recordings you have made have excessive noise or static,
the unit may be too close to a TV. Increase the distance
between the TV and the unit.
On the unit ONLY:
1 Put a recordable cassette in with the
exposed part of the tape down.
• You can use type I tape for recording.
To protect your recording
Cassettes have two small tabs
on the back to protect from
unexpected erasure or re-
recording.
To protect your recording,
remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.
2 Close the cassette holder gently and check
the recording direction for the tape.
• If the tape direction is not correct, press TAPE 2 3
twice then 7 to change the tape direction.
• If you want to record on both sides of a tape, see “To
record on both sides—Reverse Mode.”
3 Start playing the source—FM, AM or
auxiliary equipment connected to AUX
jacks.
To keep the best recording and playback sound quality
If the heads, capstans, and pinch rollers of the cassette deck
become dirty, the following will occur:
• Impaired sound quality
• When the source is the CD player, see “Disc Direct
Recording” on page 19.
• Discontinuous sound
• Fading
• Incomplete erasure
• Difficulty in recording
REC
4 Press REC (recording).
The REC (recording) indicator lights up on
the display and recording starts.
To clean the heads, capstans, and pinch rollers
Use a cotton swab moistened with alcohol.
Capstans
• If no cassette is inserted when you press REC
“NO REC” appears on the display.
• If a protected tape is inserted when you press REC
“NO REC” appears on the display.
Heads
To stop while recording, press 7.
Pinch Rollers
0
To remove the cassette, press PUSH OPEN 0
on the unit.
• If the tape is recording, stop it first.
To demagnetize the heads
Turn off the unit, and use a head demagnetizer (available at
electronics and audio shops).
DO NOT open the cassette holder when the tape is
running.
At the start and end of cassette tapes
There is leader tape which cannot be recorded onto. Thus, when
recording discs or radio broadcasts, wind the leader tape first to
ensure that the recording will be made without any loss.
To record on both sides—Reverse Mode
REV.
Press REV.MODE (reverse mode) repeatedly
MODE
until
or
is lit.
• When using the Reverse Mode for recording,
lights up and start recording in the forward
(3) direction first. Otherwise, recording will stop when
recording is done only on one side (reverse) of the tape.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Direct Recording
One Track Recording
Everything on the disc goes onto the tape in the order it is on
the disc, or according to the order you have set in Program
Play.
This recording method is convenient when you record tracks
while playing the disc. You can record just your favorite
songs on the tape.
On the unit ONLY:
On the unit ONLY:
1 Put a recordable cassette in with the
1 Put a recordable cassette in with the
exposed part of the tape down.
exposed part of the tape down.
2 Load a disc.
2 Play the track on the disc you wish to
• If the current playing source is not the CD player,
press CD 3/8, then 7 before going to the next step.
— If you do not want pauses of about 4 seconds
recorded between selections, press CD 3/8 twice.
Otherwise, a non-recorded pause will be
automatically inserted between selections.
• If you want to record on both sides of a tape, see “To
record on both sides—Reverse Mode.”
record.
REC
3 Press REC (recording).
The CD player returns to the beginning of that
track and the track is recorded on the tape.
After recording, the CD player and cassette
deck automatically stop.
4 Repeat steps 2 and 3 to record other tracks
REC
3 Press REC (recording).
you want.
The REC (recording) indicator lights up on
the display and recording starts.
To stop while recording, press 7.
The tape stops after 4 seconds.
After recording, the CD player and cassette
deck automatically stop.
0
To remove the cassette, press PUSH OPEN 0
on the unit.
• If the tape is recording, stop it first.
To stop while recording, press 7.
The tape stops after 4 seconds.
0
To remove the cassette, press PUSH OPEN 0
on the unit.
DO NOT open the cassette holder when the tape is
running.
• If the tape is recording, stop it first.
DO NOT open the cassette holder when the tape is
running.
To record on both sides—Reverse Mode
REV.
Press REV.MODE (reverse mode) repeatedly
MODE
until
• When using the Reverse Mode for Disc Direct
Recording, lights up and start recording in
or
is lit.
the forward (3) direction first. When the tape reaches its
end while recording a song in the forward direction (3),
the last song will be re-recorded at the beginning of the
reverse side (2).
If you start recording on the reverse side (2), recording
will stop when recording is done only on one side (reverse)
of the tape.
When making Sleep Timer settings while doing Disc
Direct Recording
Set enough time to allow for the disc to finish playing; otherwise,
the power will go off before recording is completed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
Continued
There are three timers available—Daily Timer, Recording
Timer, and Sleep Timer.
Before using the timers, you need to set the unit’s clock (see
page 9).
2 Set the on-time when you want the unit to
turn on.
1) Press UP or DOWN to set the hour, then press
CLOCK/TIMER.
2) Press UP or DOWN to set the minute, then press
CLOCK/TIMER.
The unit enters off-time setting mode.
Using Daily Timer and Recording Timer
UP
CLOCK
/TIMER
You can set the timer whether the unit is on or off.
DOWN
How the timer actually works
When the on-time comes, the unit automatically turns on
(the [timer] and the selected timer mode [DAILY or REC]
indicators flash just before the on-time, and continue flashing
while the timer is operating). Then, when the off-time comes,
the unit automatically turns off (standby).
[
]
DAILY
The timer setting remains in memory until you change it.
3 Set the off-time when you want the unit to
turn off (standby).
• When the DAILY indicator is lit on the display, the timer
acts as the Daily Timer. Once the timer has been set, it will
be activated at the same time everyday until the timer is
turned off.
• When the REC indicator is lit on the display, the timer acts
as the Recording Timer. After the timer-recording finishes,
the details of the setting remain stored but the timer is
turned off.
1) Press UP or DOWN to set the hour, then press
CLOCK/TIMER.
2) Press UP or DOWN to set the minute, then press
CLOCK/TIMER.
The unit enters the timer selecting mode.
4 Press UP or DOWN to select the timer
(Daily Timer or Recording Timer) with the
source to play, then press CLOCK/TIMER.
Before you start...
When using “TUNER” as the source to play, make sure to
select the desired station before turning off the power.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step 1.
• For UX-J50 only, you can also use CLOCK/TIMER on the
unit for this operation.
• Each time you press UP or DOWN, the timer mode
and the source change as follows:
DAILY
REC
TUNER
TUNER
DAILY
DAILY
CD
TAPE
DAILY TUNER: tunes in to the last station you were
listening to. (Daily Timer)
REC TUNER: records the last station you were
CLOCK
1 Press CLOCK/TIMER.
/TIMER
The (timer) indicator lights up and the
timer mode (DAILY or REC) indicator
flashes on the display.
listening to. (Recording Timer)
The unit enters on-time setting mode.
• Put a recordable cassette into the deck.
DAILY CD: plays a disc. (Daily Timer)
[
]
DAILY
• Load a disc.
DAILY TAPE: plays a tape. (Daily Timer)
• Make sure that a tape is in the cassette deck.
• Make sure that the tape direction is correct.
The unit enters the volume level setting mode.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Sleep Timer
5 Press UP or DOWN to set the volume level,
then press CLOCK/TIMER.
With the Sleep Timer, you can fall asleep to music. You can
set the Sleep Timer when the unit is turned on.
• You can select the volume level (“VOLUME – –” and
“VOLUME 0” to “VOLUME 40”).
If you select “VOLUME – –,” the volume is set to the
previous level when the unit was turned off.
How the Sleep Timer actually works
The unit automatically turns off after the specified time
length passes.
• To turn off the volume while the Recording Timer
(
REC TUNER) is working, set the volume level
“VOLUME 0.”
On the remote control ONLY:
The unit enters the clock setting mode.
SLEEP
1 Press SLEEP.
The time length until the shut-off time appears
and the SLEEP indicator lights up on the
display.
6 Adjust the clock if you need.
• See “Setting the Clock” on page 9.
• Each time you press the button, the time length
changes as follows:
STANDBY/ON
7 Press STANDBY/ON
off the unit (standby) if you have
set the timer with the unit turned
on.
to turn
SLEEP 10
SLEEP 20
SLEEP 30
SLEEP 60
SLEEP 90
• When the timer turns on the unit, the (timer) and
the selected timer mode indicators (DAILY or REC)
start flashing.
Canceled
SLEEP120
2 Wait for about 5 seconds after specifying
the time length.
CLOCK
To deactivate the timer temporarily, press
/TIMER
and hold CLOCK/TIMER until the (timer)
indicator on the display goes off.
The illumination and display dim.
To check the remaining time until the shut-off time, press
SLEEP once so that the remaining time until the shut-off time
appears for about 5 seconds.
To activate or change the timer (with the previous
setting), follow steps 1 to 7 on pages 20 and 21.
• If you want to change the timer setting after the Daily
Timer be used, first deactivate the timer.
• The illumination and display brighten during this period.
To change the shut-off time, press SLEEP repeatedly until
the desired time length appears on the display.
To cancel the setting, press SLEEP repeatedly until the
SLEEP indicator goes off.
• The Sleep Timer is also canceled when you turn off the
unit.
• If the unit is turned on when the timer on-time comes
Timer does not work.
• When you unplug the AC power cord or if a power failure
occurs
The timer will be canceled. You need to set the clock first, then
the timer again.
• If you set the Sleep Timer after the Daily Timer starts playing
the selected source
The Daily Timer is canceled. When the Sleep Timer shut-off time
comes, the unit will be turned off.
• If you set the Sleep Timer after the Recording Timer starts
recording
The Recording Timer is canceled, but recording continues until
the Sleep Timer shuts off the power.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
To get the best performance from the unit, keep your discs, tapes, and mechanism clean.
Cleaning the unit
Handling cassette tapes
• Stains on the unit
• If the tape is loose in its cassette, take up
the slack by inserting a pencil in one of
the reels and rotating.
• If the tape is loose, it may get stretched,
cut, or caught in the cassette.
Should be wiped off with a soft cloth. If the unit is heavily
stained, wipe it with a cloth soaked in water-diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
• Since the unit may deteriorate in quality, become
damaged or have its paint peel, be careful about the
following.
• Be careful not to touch the tape surface.
—DO NOT wipe it with a rough cloth.
—DO NOT wipe it strongly.
• Avoid storing tapes in the following places:
—In dusty places
—DO NOT wipe it with thinner or benzine.
—DO NOT apply any volatile substances such as
insecticides to it.
—DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
—In direct sunlight or heat
—In moist areas
—On a TV or speaker
—Near a magnet
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,
such as your dealer, for service.
Symptom
Cause
Action
No sound is heard.
• Connections are incorrect or loose.
• Check all connections and make
corrections. (See pages 6 – 8.)
• Disconnect the headphones.
• Headphones are connected.
• Antennas are disconnected.
Hard to listen to broadcasts because of
noise.
• Reconnect the antennas correctly and
securely.
• The AM loop antenna is too close to
the unit.
• Change the position and direction of
the AM loop antenna.
• The FM antenna is not properly
extended and positioned.
• Extend the FM antenna to the best
position.
The disc tray does not open or close.
The disc does not play.
The AC power cord is not plugged in.
The disc is placed upside down.
The disc is scratched or dirty.
Plug the AC power cord.
Place the disc with the label side up.
The disc sound is discontinuous.
Clean or replace the disc.
(See page 14.)
The cassette holder cannot be opened.
Impossible to record.
Power from the AC power cord has
been cut off while the tape was running. the unit.
Plug in the AC power cord, then turn on
Small tabs on the back of the cassette
are removed.
Cover the holes with adhesive tape.
Operations are disabled.
The built-in microprocessor may
malfunction due to external electrical
interference.
Unplug the AC power cord and then
plug it back in.
Unable to operate the unit from the
remote control.
• The path between the remote control
and the remote sensor on the unit is
blocked.
• Remove the obstruction.
• Replace the batteries.
• The batteries are exhausted.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Design and specifications are subject to change without notice.
Specifications
UX-J60 (CA-UXJ60 and SP-UXJ60)
UX-J50 (CA-UXJ50 and SP-UXJ50)
Amplifier
Amplifier
Output Power:
SUBWOOFERS:
Output Power:
120 W (60 W + 60 W) at 6 Ω (10% THD)
Audio input sensitivity/Impedance (at 1 kHz)
AUX:
Speakers/Impedance:
90 W (45 W + 45 W) at 6 Ω (10% THD)
MAIN SPEAKERS:
30 W (15 W + 15 W) at 6 Ω (10% THD)
Audio input sensitivity/Impedance (at 1 kHz)
400 mV/48 kΩ
6 Ω – 16 Ω
AUX:
Speakers/Impedance:
400 mV/48 kΩ
6 Ω – 16 Ω
Tuner
FM tuning range:
AM tuning range:
MW:
87.50 MHz – 108.00 MHz
522 kHz – 1 629 kHz
Tuner
FM tuning range:
AM tuning range:
MW:
87.50 MHz – 108.00 MHz
522 kHz – 1 629 kHz
CD player
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
85 dB
90 dB
Immeasurable
CD player
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
85 dB
90 dB
Immeasurable
Cassette deck
Frequency response:
Normal (type I): 60 Hz – 14 000 Hz
Cassette deck
Frequency response:
Wow and flutter:
0.15% (WRMS)
Normal (type I): 60 Hz – 14 000 Hz
Speaker—SP-UXJ50
Wow and flutter:
0.15% (WRMS)
Speaker units:
Woofer:
Midrange:
Tweeter:
12.0 cm cone x 1
4.0 cm cone x 1
2.0 cm dome x 1
Speaker—SP-UXJ60
Speaker units:
Subwoofer:
Woofer:
13.5 cm cone x 1
8.0 cm cone x 1
4.0 cm cone x 1
6 Ω
Impedance:
6 Ω
Dimensions (approx.):
160 mm x 285 mm x 181.5 mm (W/H/D)
Mass (approx.): 2.4 kg each
Tweeter :
Impedance:
Subwoofer:
Main speaker:
6 Ω
Dimensions (approx.):
Supplied Accessories
175 mm x 320 mm x 241 mm (W/H/D)
See page 6.
Mass (approx.):
3.7 kg each
Supplied Accessories
See page 6.
General
Power requirement:
Power consumption:
AC 240 V
120 W (at operation)
3.6 W (on standby)
, 50 Hz
General
Power requirement:
Power consumption:
Dimensions (approx.):
490 mm x 286 mm x 323.3 mm (W/H/D)
Mass (approx.): 10.3 kg
AC 240 V
130 W (at operation)
3.6 W (on standby)
, 50 Hz
Dimensions (approx.):
520 mm x 320 mm x 323.3 mm (W/H/D)
Mass (approx.): 12.9 kg
24
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
0503MWMMDWJEM
EN
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
|