JVC Projector DLA G10E User Manual

D-ILA Projector  
D-ILA Projector  
DLA-G10U/E Ceiling Mount  
Projecteur D-ILA  
Projecteur D-ILA  
Monture au plafond pour DLA-G10U/E  
CONTENTS  
Safety Precautions....................................................................2  
Unit Dimensions........................................................................4  
Names of Parts .........................................................................5  
Installation.................................................................................6  
Parts List ...................................................................................7  
How to Install.............................................................................8  
How to Prevent Dropping........................................................10  
Installing the Ceiling Mount on the Ceiling..............................11  
Mounting the Projector on the Ceiling Mount..........................12  
Projection Angle Adjustments .................................................13  
Replacing the Lamp and Filter ................................................14  
Specifications..........................................................................15  
EF-G10CG  
Table des matières  
Consignes de sécurité.............................................................16  
Dimensions de l’appareil.........................................................18  
Nom des pièces ......................................................................19  
Installation...............................................................................20  
Liste des pièces ......................................................................21  
Comment installer ...................................................................22  
Pour empêcher la chute..........................................................24  
Installation de la monture au plafond sur le plafond................25  
Montage du projecteur sur la monture au plafond ..................26  
Réglage de l’angle de projection.............................................27  
Remplacement de la lampe et du filtre....................................28  
Fiche technique.......................................................................29  
When installing, also read the DLA-G10U/E instruction manual.  
Thank you for purchasing this product.  
Before using your new purchase, please read this instruction manual thoroughly. And, after  
reading, be sure to store this instruction manual in a safe place for future reference.  
Pour l’installation, se reporter également au mode d’emploi du DLA-G10U/E.  
Nous vous remercions d’avoir acheté ce produit.  
Avant d’utiliser votre projecteur, veuillez lire attentivement toutes les instructions de ce  
manuel. Puis, après l’avoir lu, rangez-le en lieu sûr de façon à pouvoir vous y reporter.  
In s t ru c t io n Ma n u a l  
Mo d e d o e m p lo i  
BHU30002-028-01  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
CAUTION  
To assure safety, special techniques are  
required for installation. The customer should  
never perform this work. Consult your dealer  
concerning installation.  
Do not install in locations subject to low or high  
temperatures, near a kitchen table or  
humidifier, or where there is oil smoke or water  
vapor. This can result in projector malfunction,  
deterioration of image quality, fire or electrical  
shock.  
Do not install the projector in a box or other  
closed space where the hot air from the  
projector cannot be exhausted. Do not block  
the exhaust port of the projector. Projector  
overheating can result in malfunction, loss of  
image quality or electrical shock.  
Provide sufficient reinforcement when the  
ceiling on which this product will be installed is  
too weak. Install so as to prevent any safety  
related problems. If the ceiling is too weak or  
the installation is improperly performed, this  
product could possibly drop and cause injury  
or damage.  
Permissible temperature range:  
5 - 35 degrees C  
Permissible humidity range:  
20% - 80%, no condensation.  
CAUTION  
When replacing the lamp or filter, provide a  
solid footing from which a comfortable posture  
can be adopted. Working with an unstable  
footing or in an uncomfortable posture can  
result in injury or damage. When the  
HANDLING PRECAUTIONS  
Please observe the following cautions to  
prevent malfunction or deterioration of the  
product.  
installation work is difficult, lower to a safe  
height and call a professional installer.  
Do not install where there is danger of contact with  
excessive dust, oil smoke, tobacco smoke, water  
vapor. etc. These will adhere to the lens, liquid crystal  
panel, mirror, etc., and result in blurred or dark  
images.  
Never suspend or hang objects from the  
ceiling mount. An excessive load can cause  
the ceiling mount to fall and result in injury or  
damage.  
Install in a room that can be darkened to prevent  
direct sunlight, illumination or reflected light on the  
screen. Such light will cause the images to appear  
whitish and be hard to view. Use curtains in rooms  
where light enters from the outside.  
This product is to be used only for ceiling  
mounting. Do not use it for any other  
application. And never make alterations  
because this can cause an accident.  
Do not mount any projector other than the  
DLA-G10U/E on this product. This could result  
in an accident.  
Do not install where there is danger of  
vibration or impact. This could cause the  
ceiling mount to drop and result in injury or  
damage.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNIT DIMENSIONS  
All dimensions below are given in mm.  
3-Ø11Elongated holes  
Ø11  
200  
240  
454  
436  
402  
396  
72  
223  
5˚  
5˚  
15˚  
15˚  
These specifications are subject to change without notice.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
NAMES OF PARTS  
Tilt adjustment screw  
Tilt adjustment screw  
Tilt fulcrum (pivot) screw  
Ceiling mount  
The same screws are also used on the opposite side.  
Vertical/horizontal adjustment screws  
The same screws are also used on the opposite side.  
Vertical angle adjustment screws  
L-plate  
Horizontal angle  
adjustment bolts. Use the  
hex wrench provided.  
Pin  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Special techniques are necessary for safe installation. The customer should never perform  
the installation work.  
Consult your dealer concerning installation.  
Projection Distance and Screen Size  
This projector uses a 1.5X zoom lens; therefore, the maximum projected image size is 1.5 times larger than the minimum  
projected image size.  
Focus is possible at projection distances of from 2.5m to 20m. Use the distances shown below for reference.  
Screen size (type)  
min. - Max. (zoom)  
Distance from the front screw  
of the ceiling mount to the screen: L (m)  
41.4 ~ 61.9  
170 ~253.9  
341.5 ~509.8  
2.5  
10  
20  
If the edges of images are distorted when projecting at the minimum project distance, it is recommended that the projector be  
moved slightly backward.  
Install the projector in a stable location away from walls and furniture for safety during light source lamp and filter  
replacement.  
350mm  
Example: 317.5mm  
Wall,  
furniture,  
etc.  
300mm  
Wall, furniture, etc.  
The center-lines of the  
projector lens and the ceiling  
mount are not aligned.  
500mm  
L
Screen  
172mm  
72mm  
90˚  
200mm  
Wall, furniture, etc.  
CAUTION  
Do not install in locations such as those shown below since this could result in malfunction or fire.  
· Box or other closed space where ventilation is not possible.  
· Places where there is oil smoke, water vapor or tobacco smoke.  
· Humid or dusty places.  
· Places where the temperature is low or high and the humidity is outside the permissible operating range.  
Permissible temperature range: 5 - 35 degrees C  
Permissible humidity range  
:20% - 80% (no condensation)  
Direct sunlight and indoor lighting can cause the screen to appear whitish and difficult to view. Use curtains to  
shut out light when necessary.  
Install the projector as level as possible; otherwise, malfunction may occur.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST  
The following parts are provided as accessories with this projector. Make sure all of the parts are present before stating the  
installation work.  
1. Ceiling mount  
1
1
1
2. Drop prevention fixture  
2
1
1
3. Hex wrench  
1
1
1
4. Hex bolt  
5. Flat washer  
6. Spring washer  
(M5 8mm)  
7. Screw  
8. Flat washer  
9. Spring washer  
(M8 15mm)  
Completion drawing  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO INSTALL  
Do not connect the power plug to a power outlet until all preparations have been  
completed.  
CAUTION  
1
Extend the two legs of the DLA-G10U/E by rotating.  
Prepare the following tool  
Rotate until rotation becomes stiff and then stop to prevent damage. The other legs of  
the projector do not rotate. Peel off the rubber pad adhered to one of the legs so the  
embedded nut is visible.  
Screwdriver  
Rubber pad  
Leg  
2
Remove the 4 adjustment screws and remove the ceiling mount. Remove the 2  
screws from the ceiling mount and open the mount 90 degrees. Remove 2 screws  
and then detach the stopper from the front of the mount.  
Ceiling mount  
Top fitting  
Stopper  
Vertical adjustment screw  
Hinge  
Use care to prevent the top fitting from dropping during the installation work since this  
could result in injury or damage.  
CAUTION  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO INSTALL  
3
Install the ceiling mount on the DLA-G10U/E by aligning the holes and cutouts, then install the stopper.  
Top fitting  
CAUTION  
Use care to prevent the top fitting from dropping  
during the installation work since this could result in  
injury or damage.  
Stopper  
Prepare the following accessories  
4
Firmly tighten the accessory screw (M8 15mm) and the two DLA-G10U/E legs.  
Spring washer (1)  
Screw (M8 15mm)  
M8 15mm (1)  
Flat washer (1)  
Spring washer  
Flat washer  
Completion drawing  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO PREVENT DROPPING  
1
Remove the U-fitting mounting screws.  
U-fitting  
2
Attach a drop prevention chain or wire to the U-fitting and fasten firmly with a screw.  
Procure a drop  
prevention chain or  
If a chain is attached  
wire of sufficient  
strength.  
M5 8 bolt  
Spring washer  
To ceiling  
3
Mount the drop prevention fixture on the ceiling mount.  
Flat washer  
Prepare the following accessories  
Drop prevention  
fixture  
M5 8 bolt (1)  
Hex wrench  
Spring washer (1)  
Flat washer (1)  
Drop prevention fixture (1)  
4
Attach the drop prevention fixture to the ceiling using the same procedure as described in items 1 - 3.  
[ Typical Installation ]  
In case of a wood ceiling  
In the case of a concrete ceiling  
Anchor (M5)  
Ceiling  
Beam  
Mounting plate  
Use materials that  
will withstand the  
weight of the  
projector and the  
ceiling mount.  
Mounting bolt (M5)  
To ceiling mount  
Mounting bolt (M5)  
To ceiling mount  
1 Drill a hole through the mounting plate, beam  
and ceiling.  
2 Pass the mounting bolt (M5) through the hole  
and fasten the drop prevention fixture.  
1 Drill a hole in the ceiling and then drive in the  
anchor (M5).  
2 Securely fasten the drop prevention fixture  
with mounting bolts (M5).  
The M5 bolts for  
ceiling mounting  
are to be procured  
separately. Consult  
your dealer.  
Be sure to mount the drop prevention fixture directly above the projector. Consult your  
dealer concerning the ceiling installation work.  
CAUTION  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLING THE CEILING MOUNT ON THE CEILING  
Install the ceiling mount on the ceiling.  
To ensure safety, special techniques are required for installation. Do not attempt to perform the installation work  
yourself.  
200  
Mounting bolt  
(M10 4, procure separately)  
The M10 bolts for  
ceiling installation  
are to be procured  
separately. Consult  
your dealer.  
Consult your dealer concerning  
installation. This company  
assumes absolutely no  
Ceiling mount  
responsibility if the projector  
drops due to insufficient  
installation strength.  
Temporarily fasten with four M10 bolts in the sequence of  
accurately and then securely tighten the four M10 bolts.  
The total weight of the projector and ceiling mount is 20.5kg.  
,
and  
position  
,
Install at a sufficient distance, referring to the projection distance range table on  
page 6.  
[ Typical Installation ]  
In case of a wood ceiling  
In the case of a concrete ceiling  
Anchor  
Ceiling  
Beam  
Mounting plate  
Use materials that  
will withstand the  
weight of the  
(M10)  
projector and the  
ceiling mount.  
Mounting bolt (M10)  
To ceiling mount  
Mounting bolt (M10)  
To ceiling mount  
1 Drill holes of the above size in the ceiling and  
mounting plate.  
1 Drill holes of the above size in the ceiling and  
then drive in the anchor (M10).  
2 Drill holes in the beam.  
3 Insert the mounting bolts (M10) through the  
holes and fasten the ceiling mount. Make sure  
2 Securely fasten the ceiling mount with a  
mounting bolt (M10). Use anchors that will  
support the weight of the projector and ceiling  
mount.  
the weight is supported by the beam. Reinforce  
the beam if its strength is insufficient.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING THE PROJECTOR ON THE CEILING MOUNT  
1
Engage the L-plate on the pin of the ceiling mount.  
Ceiling mount  
Drop prevention fixture  
L-plate  
Pin  
2
Fasten temporarily with the vertical angle adjustment screws (4) which were removed. After fastening with the vertical  
adjustment angle screws (4), perform the adjustments described on page 13.  
Vertical angle  
adjustment screw  
M5 15 screws (4)  
Prepare the following tool  
Screwdriver  
Completion drawing  
Accessories to remove from  
the projector  
M5 15 screws  
(4)  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROJECTION ANGLE ADJUSTMENTS  
Pre-adjustment Operations  
· Look at the projector instruction manual and turn on the power.  
· Use the zoom lens to match the projected image size to the size of the screen.  
Perform the above operations before starting the projection angle adjustments.  
Horizontal angle adjustment (top view)  
1 Use the accessory hex wrench to loosen 6  
bolts.  
7˚  
2 Move the projector left and right to center the  
projected image horizontally on the screen.  
3 When the angle has been correctly adjusted,  
fasten the projector securely by tightening the  
bolts.  
7˚  
Vertical angle adjustment (side view)  
15˚  
4 Center the projected image on the screen  
vertically and then fasten the projector  
securely by tightening the bolts.  
15˚  
Tilt angle adjustment (rear view)  
5 Use the tilt adjustment screws (4 locations: 2  
in front and 2 at the rear) to adjust the  
projector so that the projected image is not  
tilted in relation to the screen, then securely  
tighten the screws.  
5˚  
5˚  
Repeat the above adjustments if the  
projected image is still unsatisfactory.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACING THE LAMP AND FILTER  
Observe the following cautions when replacing the light source lamp or filter. Failure to  
do so can result in personal injury or projector damage.  
· Turn off the POWER button of the remote control or OPERATE button of the projector  
and disconnect the power cord from the power outlet.  
· Take precautions to keep the DLG-G10U/E main unit and lens away from furniture,  
lamps, etc.  
· Prepare a stable place to stand where you can work comfortably. When the  
installation work is difficult, lower to a safe height and call a professional installer.  
CAUTION  
1
To replace the lamp and filter, remove 2 screws while supporting the DLA-G10U/E with the hands and then lower it gently.  
When removing the screws, always insert  
the accessory hex wrench to prevent the  
projector dropping suddenly.  
2
Replace the lamp and filter. (Replace in accordance with the instructions given in the DLA-G10U/E instruction manual.)  
Filter  
Lamp  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Part name : Ceiling mount  
Model : EF-G10CG  
Application : Ceiling mounting the DLA-G10U/E projector  
Applicable projector : DLA-G10U/E only  
Vertical tilt range : +/-15 degrees  
Horizontal tilt range : +/-5 degrees  
Horizontal pan range : +/-7 degrees  
Fixture Mass : 6.2kN  
Fixture size : 454mm (W) 359mm (D) 176mm (H)  
Mass with projector mounted : 20.5kN  
External dimensions with projector mounted : 454mm (W) 402mm (D) 377.5mm (H)  
Accessories : M8 15 screw (1), flat washer (1)  
Spring washer (1)  
M5 8 hex bolt (1), flat washer (1)  
Spring washer (1)  
Drop prevention fixture (2)  
Hex wrench (1)  
Instruction manual (1)  
Service network (1)  
· The specifications and appearance of this product are subject to change without notice.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Speaker DPF 8000 User Manual
Intel Laptop ATX BX2 User Manual
Jensen Car Stereo System CD510K User Manual
John Lewis Freezer JLBIUCF 01 User Manual
John Lewis Range JLBIGH601 User Manual
Kenmore Range 7907042 User Manual
KitchenAid Ventilation Hood KWCU205H User Manual
Kobe Range Hoods Ventilation Hood RA2830SB User Manual
Kompernass DVD Player KH 6502 User Manual
Konica Minolta Digital Camera KD 500Z User Manual