DIGITAL STILL CAMERA
ENGLISH
GC-S1
Please visit our CyberCam Homepage on
the World Wide Web and answer our
Consumer Survey (in English only):
STILL CAMERA
INSTRUCTIONS
LYT0143-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
EN
3
This unit is produced to comply with Standard
IEC Publ. 65.
CAUTION:
To avoid electric shock or damage to the unit,
first firmly insert the small end of the power
cord into the AC Power Adapter until it is no
longer wobbly, and then plug the larger end of
the power cord into an AC outlet.
SOME DO’S AND DON’TS ON THE SAFE USE
OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards
but, like any electrical equipment, care must be taken if you are to obtain the best results and
safety is to be assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and in accordance with the manufacturer’s instruc-
tions. Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equip-
ment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way — switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed
for unattended operation or has a standby mode. Switch off using the switch on the equipment and
make sure that your family knows how to do this. Special arrangements may need to be made for
infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements
of road safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating
will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit
the manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone especially children push anything into holes, slots or any other opening in the case
— this could result in a fatal electrical shock;
— NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK START
4
EN
Power Dial
1
Lock button
Four LR6 (AA)-size
alkaline batteries
2
BATTERY cover
Load batteries. (੬ pg. 8)
Slide the BATTERY cover slightly to open.
1
2
Insert four LR6 (AA)-size batteries as indicated
by the orientation marking inside the cover.
Turn the power on. (੬ pg. 14)
Turn the Power Dial to “ A ”.
1 •Turn while holding the Lock Button de-
Zoom Button
2
pressed.
Shutter Release Button
2
190°
1
1
Power Dial
Lock button
Play an image. (੬ pg. 31)
Shoot an image. (੬ pg. 16)
Turn the Power Dial to “PLAY ”.
Tilt the lens and point it at the subject.
1 •Turn while holding the Lock Button de-
1
pressed.
Press the Shutter Release Button.
•A still image stored in memory appears.
2 •A still image is stored in the camera's
Select an image with the Zoom Button.
memory.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAJOR FEATURES
EN
5
10X Zooming for Magnifying Faraway Subjects
When a subject is located too far away to be approached, its image
can be enlarged using 10X zooming.
An image shot by zooming has much higher quality than a non-
zoomed image enlarged using image processing software on a PC.
Cordless Image Transfer Using Infrared Communication (IrTran-P Compatible)
IrTran-P is the most advanced infrared communication protocol
available today.
Images can be transferred to another piece of equipment without
using a cable, provided that it is compatible with the IrTran-P
standard.
Compact Flash Card for Shooting More Images
The Compact Flash card makes it possible to shoot and store
images in addition to those that can be stored in the built-in
memory.
The extra available images mean you don’t have to worry about
missing great shots. Also, by using several Compact Flash cards,
you can make a library of images archived by category, or you can
create personal archives for each person when a single camera is
shared by several users.
COMPACTFLASH and
are trademarks of SanDisk Corporation,
registered in the U.S.A. and other countries.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
6
EN
SAFETY PRECAUTIONS
QUICK START
2
4
5
6
8
MAJOR FEATURES
CONTENTS
GETTING STARTED
Loading Batterirs ............................................................................... 8
Unloading Batteries ............................................................................ 8
Hand Strap Attachment........................................................................ 8
Houehold Power Supply ....................................................................... 9
Date/Time Setting ........................................................................... 10
BASIC OPERATION
12
Lens Adjustment .............................................................................. 12
Shutter Release Button ...................................................................... 12
Brightness Control............................................................................ 13
Shooting Mode Selection .................................................................... 14
Picture Mode Selection ...................................................................... 15
Simple Shooting (Full Auto Shooting) ...................................................... 16
Camera Setup Check ......................................................................... 17
Zoom Shooting................................................................................ 18
Self-Timer Shooting .......................................................................... 19
Flash Shooting ................................................................................ 20
MANUAL SHOOTING
21
Exposure Control ............................................................................. 21
White Balance Control ....................................................................... 22
Adjusting the White Balance............................................................. 22
Adjusting the White Balance Manually (M.W.B.) ..................................... 23
Shutter Speed Selection ..................................................................... 24
Selecting the Shutter Speed.............................................................. 24
Shutter Speeds and Effects .............................................................. 25
Manual Focusing .............................................................................. 26
View Mode Selection ........................................................................ 27
Power Save Mode............................................................................ 28
Flash Adjustment ............................................................................. 29
PLAYBACK
30
Playback Through a TV Monitor or VCR................................................... 30
Normal Playback ............................................................................. 31
Auto Playback ................................................................................ 31
INDEX Screen ................................................................................. 32
Index Playback ............................................................................... 33
Protecting Images ............................................................................ 34
Deleting Images .............................................................................. 36
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
7
Applying Sepia/Black-and-White Effects ................................................. 38
Magnifying the Playback Image (Zoom) .................................................. 39
Types of Frames .............................................................................. 40
Framing an Image ............................................................................ 41
Multi-Image Screen .......................................................................... 42
APPLIED OPERATIONS
44
Compact Flash Card Operation.............................................................. 44
Installing a Compact Flash Card ......................................................... 44
Removing a Compact Flash Card ........................................................ 44
Initializing the Storage Media .............................................................. 45
Storing Images in a Compact Flash Card .................................................. 46
Playing Back Images Stored in a Compact Flash Card ................................... 46
Copying Images Between the Built-in Memory and a Compact Flash Card ........... 47
Image Copy Using Infrared Communication [IrTran-P] .................................. 50
Printing on a Digital Printer [IrDA Transfer] .............................................. 52
PC Connection Operation .................................................................... 53
CONTROLS, CONNECTORS AND INDICATORS
TROUBLESHOOTING
DISPLAY AND MESSAGES
CAUTIONS
54
60
62
63
66
67
MAJOR SPECIFICATIONS
INDEX
PROVIDED ACCESSORIES
x 1 for Windows® PC
x 1 for Macintosh®
LR6 (AA)-size
alkaline battery x 4
Video cable
Hand strap
PC connection cable
CD-ROM
• Picture Navigator
• MGI PhotoSuite SE
Soft case
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Unloading Batteries
8
EN
Loading Batteries
Use LR6 (AA)-size dry cell batteries.
1
2
BATTERY
Cover
Open the battery cover by performing step 1
of “Loading Batteries” to the left.
1
2
Take out batteries by tilting the camera
slightly.
NOTES:
● Do not use manganese batteries as they do not
have sufficient energy to power this camera.
● If the batteries are not used for an extended
period, remove them from the camera to avoid
battery leakage, which can cause malfunctions to
occur.
3
● Since batteries become very hot after they are
exhausted, be careful when replacing them with
new ones.
● Replace the batteries when the battery power
remaining indicator displays the red mark.
Slide the battery cover (BATTERY) slightly to
open.
•The battery cover opens.
1
2
green
Hand Strap Attachment
2
red
Insert batteries as indicated by the orientation
marking inside the battery cover.
Close the battery cover and slide it back.
3 •The battery cover is locked in the closed
position.
•Make sure the battery cover is closed
securely.
Loop
NOTES:
1
● Commercially-available LR6 (AA)-size nickel-
cadmium (Ni-Cd) or nickel-metal hydride (Ni-
MH) batteries can also be used. Ni-Cd or Ni-MH
batteries are more economical because they can
be recharged and used repeatedly. Be sure to read
their instructions.
3
Open the jack cover.
1
2
● Inserting batteries in the incorrect direction may
cause them to leak.
Thread the end of the hand strap through the
camera's eyelet, then thread the loop of the
hand strap through the end.
Close the cover.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
9
Household Power Supply
When using the camera indoors, it is more convenient and economical to power it from a household AC
power outlet using an AC power adapter (optional).
To AC outlet
3
AA-V33 AC power
adapter (optional)
2
1
Core filter
Core filter
NOTES:
Connect the Power Cord to the AC Power
Adapter.
•Make sure connections are secure.
● The optional AA-V33 AC Power Adapter features
automatic voltage selection in the AC range from
110 V to 240 V.
1
2
● Make sure the Power Cord is securely connected
to the AC Power Adapter.
Connect the DC Cord to the DC Input
Connector of the Digital Still Camera.
● When using the AC Power Adapter, use only the
Power Cord provided with the AC Power Adapter.
Use of any other cord may result in shock or fire.
● Connect the Power Cord to the AC Power Adapter
before connecting it to an AC outlet. If you plug it
into an outlet first, and the Adapter’s terminals
come in contact with a metal surface or object,
short circuit or fire may result.
Connect the Power Cord to an AC outlet.
3 •After use, unplug the Power Cord from the
AC outlet.
● Vibration noise can sometimes be heard coming
from the inside of the AC Power Adapter. This is
normal.
● The AC Power Adapter processes electricity
internally, and will become warm during use. This
is normal. Make sure to use the AC Power
Adapter in well-ventilated areas only.
ATTENTION:
Before detaching the power source, make
sure that the camera’s power is turned off.
Failure to do so may cause the camera’s
built-in memory to be corrupted.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED (cont.)
10
EN
Date/Time Setting
By setting the date and time, date/time data can be viewed along with your pictures.
Date/time data is also convenient for categorizing pictures later.
MENU Jog Dial
Power Dial
Lock Buton
LCD monitor
Turn the Power Dial, while pressing its Lock
M
1
2
3
Button, to “ ” and push the MENU Jog Dial.
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
CAMERA MENU
Screen
•The CAMERA MENU Screen appears.
Rotate the MENU Jog Dial to select “SYSTEM”
and push it.
•The SYSTEM Setup Screen appears.
Rotate the MENU Jog Dial to select “DATE/
TIME” and push it.
SYSTEM
POWER SAVE
FLASH ADJ .
DATE / T IME
EX I T
•The DATE/TIME Setup Screen appears.
•If you wish to set only the time without
changing the date, go to step 5.
SYSTEM Setup Screen
DATE / T I ME
DATE/TIME Setup
Screen
DATE
27 . 12 . 1998
T IME
24-hour indication
9 : 30
EX I T
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
11
LCD monitor
Set the values for the date.
4 1. Rotate the MENU Jog Dial to select the item
DATE / T I ME
in the “DATE” section you wish to set and
push it.
DATE/TIME Setup
Screen
DATE
27 . 12 . 1998
•The item colour changes to indicate that
setting is possible.
2. Rotate the MENU Jog Dial until the correct
setting appears and push it.
•Repeat this procedure until you are
satisfied with the date settings.
• If you wish to set only the date without
changing the time, go to step 6.
T IME
9 : 30
EX I T
DATE / T I ME
Set the values for the time.
DATE
5 1. Rotate the MENU Jog Dial to select the item
27 . 12 . 1998
in the “TIME” section you wish to set and
push it.
T IME
9 : 30
•The item colour changes to indicate that
setting is possible.
2. Rotate the MENU Jog Dial until the correct
setting appears and push it.
EX I T
•When the MENU Jog Dial is pushed after
the minutes are set, “EXIT” is selected and
clock operation starts from 0 seconds.
•Repeat this procedure until you are
satisfied with the time settings.
DATE / T I ME
DATE
27 . 12 . 1998
T IME
Rotate the MENU Jog Dial to select “EXIT”
and push it 3 times.
14 : 20
6
EX I T
•The shooting screen reappears and the clock
starts functioning.
14 : 20 : 00
DATE / T I ME
NOTES:
DATE
● The date/time setting is backed up by a built-in
rechargeable clock battery. Connect the camera
to an AC outlet using the AC power adapter for
over 24 hours to charge the clock battery.
● The clock will continue to advance except while
the minutes are being set. When the minutes are
set and the MENU Jog Dial is pushed, the seconds
are reset to “0” and clock operation starts.
● Although the date/time which you have set is
stored in the camera’s built-in memory, the date/
time display will not be combined with the
pictures you shoot.
27 . 12 . 1998
T IME
14 : 20
EX I T
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
12
EN
Lens Adjustment
Shutter Release Button
To obtain the most stable position for shooting
while viewing the LCD monitor, hold the lens so
that it forms an angle of 45 degrees in relation to
the camera body.
The Shutter Release Button of the camera has two
steps. At the first step, when the button is pressed
halfway, “
” is displayed and the camera
automatically focuses on the subject. “
”
The lens tilts up to 100 degrees forward and 90°
backward. You can photograph yourself, while
viewing your own image on the LCD monitor (Self-
Recording), by tilting the lens 90 degrees backward
and taking your picture. This can be used for things
such as keeping a photo diary.
disappears once the subject has been brought into
focus.
The operation of pressing the Shutter Release Button
to the first step is called a “half-press”. From the
“half-pressed” position, press the button all the way
to the second step.
Unpressed
position
100°
90°
Half-pressed
position
Fully-pressed
position
NOTES:
● Do not press the Shutter Release Button with your
finger raised over the button or do not press it
with too strong a force, as this may disrupt the
horizontal positioning of the image or cause
blurring. When shooting, always half-press the
button before pressing it fully to the second step.
● If focusing is performed by pressing the Shutter
Release Button frequently during auto focus, the
period between when the Shutter Release Button
is pressed and when the shutter is released will be
shortened.
● While the camera is performing auto focusing
with the button half-pressed, the displayed image
may freeze temporarily. This is not a malfunction.
● When the Shutter Release Button is released from
the half-pressed position and half-pressed again,
the camera performs auto focusing again.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
13
BRIGHT Dial (MENU Jog Dial)
To darken the image
To brighten the image
Brightness Control
You can adjust the brightness of the LCD monitor by rotating the BRIGHT dial, except during manual
focusing or menu adjustment.
To darken the image . . .
Rotate the BRIGHT dial upward.
To brighten the image . . .
Rotate the BRIGHT dial downward.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION (cont.)
14
EN
Shooting Mode Selection
Turning the Power Dial allows you to select the appropriate shooting mode from among the following:
A
M
Full Auto mode ( ), Manual mode ( ) and Self-Timer mode (
).
Power Dial
Lock Button
A
“
“
“
” : Full Auto mode
The camera will automatically control all items including exposure, shutter speed, focusing and
white balance.
M
” : Manual mode
Exposure, shutter speed, focusing and white balance can be controlled manually according to the
shooting conditions.
” : Self-Timer mode
A 15-second self-timer can be used.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
15
Pictrue Mode Selection
The Picture Quality mode can be selected to best match your needs. Three Picture Quality modes are
available: FINE, STD (standard) and ECONOMY (in order of quality).
MENU Jog Dial
Power Dial
Lock Button
LCD monitor
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
P I CTURE MODE
F I NE
STD
ECONOMY
EX I T
CAMERA MENU Screen
PICTURE MODE Screen
NOTES:
Turn the Power Dial, while pressing its Lock
● The number of storable images depends on the
selected Picture Quality mode, the conditions
under which the camera is used, the temperature
during use of the camera and the batteries being
used.
M
1
2
3
Button, to “ ” and push the MENU Jog Dial.
•The CAMERA MENU Screen appears.
Rotate the MENU Jog Dial to select “PICTURE
MODE” and push it.
● The selected Picture Quality mode is used even
when the Power Dial is turned to positions other
•The PICTURE MODE Screen appears.
M
than “ ”.
Rotate the MENU Jog Dial to select the
“FINE”, “STD” or “ECONOMY” Picture
Quality mode and push it.
•The Picture Quality mode is set, and the
CAMERA MENU Screen appears.
Push the MENU Jog Dial.
4 •The shooting screen reappears.
PICTURE QUALITY
MODE
Number of Storable Images
(in Built-in Memory)
FINE
Approx. 30
STANDARD (STD)
ECONOMY
Approx. 50
Approx. 100
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION (cont.)
16
EN
Simple Shooting (Full Auto Shooting)
In the Full Auto mode, the camera controls focusing, shutter speed, exposure and white balance automati-
cally to make your shooting simple and easy.
Shutter Release Button
Power Dial
Lock Button
NOTES:
Turn the Power Dial, while pressing its Lock
● When the Shutter Release Button is half-pressed,
A
1
2
Button, to “ ”.
auto focusing is performed.
•The camera turns on in the Full Auto mode.
● After storing images in the built-in memory, it is
recommended that you transfer them to a
Compact Flash card or PC.
Train the lens on the subject to be photo-
graphed.
•If the low light “ ” icon appears on the LCD
monitor, use the flash (੬ pg. 20).
Press the Shutter Release Button.
3 •The image will be stored in the built-in
memory or Compact Flash card.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
17
Camera Setup Check
Camera setup items that can be checked include the image storage location (only when stored in a Compact
Flash card), Picture Quality mode, number of shots taken, remaining battery power, date and time. For
details, see “On-Screen Display During Shooting” (੬ pg. 57, 58).
LCD monitor
CF
F I NE
0 2 1 / 0 3 0
+ 2 1 / 1 0 0 0
2 7 . 1 2 . 1 9 9 8
1 4 : 0 5 : 2 3
DISPLAY Button
Standard View with Information Display mode
Standard View with
Information Display
mode (colour display)
Standard View mode
(colour display)
Quick View mode
(monochrome display)
● Each press of the DISPLAY Button switches the View mode. The camera setup can be
checked in the Information Display Screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION (cont.)
18
EN
Zoom Shooting
The camera incorporates a 10X zooming function that corresponds to a 43 mm to 430 mm lens of a 35 mm
camera. Zooming allows you to shoot wide areas, as well as close-ups of subjects located far away, without
changing the shooting position.
W
T
W (Wide-angle) zooming
A relatively wide area can be
photographed.
T (Telescopic) zooming
A faraway subject can be
magnified and photographed.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
Self-Timer Shooting
When the Self-Timer is activated, the camera shutter is automatically released 15 seconds later. Once the
camera is set, the camera operator can become part of the scene. This function can also be used to prevent
blurring caused by subtle hand movements when the Shutter Release Button is pressed.
Shutter Release Button
Self-Timer Lamp
Blinks.
Lock Button
Power Dial
NOTES:
Turn the Power Dial, while pressing its Lock
● The Self-Timer Lamp starts blinking faster when
1
Button, to “ ”.
there are 5 seconds or less remaining before the
shutter is released.
● If you wish to cancel the Self-Timer half-way, turn
the Power Dial to any position except “ ”.
● Focusing is performed when the Shutter Release
Button is pressed.
•“ ” appears.
•If the low light “ ” icon appears on the LCD
monitor, use the flash (੬ pg. 20).
Press the Shutter Release Button.
2 •The Self-Timer Lamp and the on-screen “
”
icon start blinking, then the shutter is
released 15 seconds later.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION (cont.)
20
EN
Flash Shooting
Use the flash when the low light “ ” icon appears on-screen during indoor shooting or under low light.
Flash
MENU Jog Dial
Power Dial
Lock Button
FLASH/TRANSFER Button
Flash Lamp
To take another shot with a flash . . .
A
Make sure that the Power Dial is set to “ ”,
.... repeat the above steps.
M
1
2
“
” or “ ”, then press the FLASH/TRANSFER
Button.
Flash Adjustment
•The Flash Lamp starts blinking and the flash
begins charging.
The flash intensity can be increased or decreased by
2 steps. For details, see “Flash Adjustment”
(੬ pg. 29).
When charging is complete, the Flash Lamp
stops blinking but stays lit, and the flash “ ”
icon appears on the LCD monitor.
•If no operation is performed while the flash
icon is displayed, the flash icon disappears.
When this occurs, press the FLASH/
TRANSFER Button again.
•To abort flash shooting before taking a
picture, press the FLASH/TRANSFER Button
again.
NOTES:
● While the flash is charging, the LCD monitor turns
off to save power. This is not a malfunction. Once
the flash is charged after a few seconds, the LCD
monitor turns on again.
● When the batteries are nearly exhausted during
flash shooting, the power may turn off.
● During Self-Recording, the flash is not charged
and does not emit light.
● Since flash shooting consumes a large amount of
battery power, it is recommended to keep a spare
set of batteries nearby when you are planning to
take many photographs with the flash.
● When battery power weakens, the time it takes for
the Flash Lamp to light steadily increases, and
flash charging may be aborted. Before pressing
the Shutter Release Button, make sure the Flash
Lamp stays lit.
Aim the flash at the subject and press the
Shutter Release Button.
•The flash emits light and the Flash Lamp
turns off.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SHOOTING
Exposure Control
EN
21
When the subject appears too dark or too bright on the LCD monitor, it may be necessary to compensate for
the ambient brightness. This will make it possible to capture the contours of the dark and bright regions of
the image more clearly.
NOTE:
Use the flash when the low light “ ” icon appears.
MENU Jog Dial
Power Dial
Lock button
To darken the image
To brighten the image
LCD monitor
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
CAMERA
EXPOSURE
M .W. B .
SHUTTER
SPEED
EXPOSURE
0
+6
AUTO
EX I T
AUTO
EX I T
CAMERA MENU Screen
EXPOSURE Setup Screen
CAMERA Setup Screen
Turn the Power Dial, while pressing its Lock
Rotate the MENU Jog Dial to adjust the
exposure.
M
1
Button, to “ ” or “ ” and push the MENU
5
Jog Dial.
•The exposure value can be selected from –6
and +6.
•The CAMERA MENU Screen appears.
To brighten the image:
Rotate the MENU Jog Dial to select
“CAMERA” and push it.
Increase the exposure value. (maximum +6)
2
3
4
To darken the image:
Decrease the exposure value. (maximum –6)
•The CAMERA Setup Screen appears.
Rotate the MENU Jog Dial to select
“EXPOSURE” and push it.
•The EXPOSURE Setup Screen appears.
Push the MENU Jog Dial twice.
6 •The EXPOSURE Setup Screen disappears.
•The exposure value is set and the shooting
screen reappears.
Rotate the MENU Jog Dial to select the
current value and push it.
To adjust a previously set exposure value . . .
.... repeat the above procedure from step 1.
•The item colour changes to indicate that
setting is possible.
NOTE:
To set the exposure value to the standard level, set
the exposure value to “0” or turn the Power Dial to
A
“
”.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SHOOTING (cont.)
22
EN
White Balance Control
Adjusting the White Balance
If the image appears greenish, reddish or bluish, it may be necessary to adjust the white balance of the
camera. From the list of presets (“ ”, “ ” or “ ”), select the one that makes the colours in the image look
the most natural. If the colours appear only slightly unnatural, select “AUTO”.
Power Dial
MENU Jog Dial
Lock Button
LCD monitor
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
CAMERA
EXPOSURE
M .W. B .
SHUTTER
SPEED
M.W. B .
0
AUTO
AUTO
MWB
EX I T
AUTO
EX I T
CAMERA MENU Screen
M.W.B. Setup Screen
CAMERA Setup Screen
Turn the Power Dial, while pressing its Lock
Button, to “M ” or “ ” and push the MENU
Jog Dial.
Rotate the MENU Jog Dial to select “ ”,
1
4
“
”, “ ” or “AUTO” and push it.
•Select the preset that can provide the subject
with the most desirable white balance.
•The CAMERA MENU Screen appears.
The following 5 options can be selected.
AUTO ......Select this position to adjust the
colour balance automatically.
When the Full Auto mode is
selected with the Power Dial, this
position is selected automatically.
............ Select for shooting outdoors on a
fine day.
Rotate the MENU Jog Dial to select
“CAMERA” and push it.
2
3
•The CAMERA Setup Screen appears.
Rotate the MENU Jog Dial to select “M.W.B.”
(Manual White Balance) and push it.
•The M.W.B. Setup Screen appears.
...........Select for shooting on a cloudy day
or in the shade.
.............Select for shooting with in-
candescent lamps or video lighting,
etc.
MWB .......Select to photograph the subject
with a previously adjusted colour
balance (੬ pg. 23).
NOTE:
If a satisfactory white balance cannot be obtained
with any of the “ ”, “ ”, “ ” or “AUTO”
positions, adjust the white balance manually as
indicated in “Adjusting the White Balance Manu-
ally” (੬ pg. 23).
Push the MENU Jog Dial twice.
5 •The M.W.B. Setup Screen disappears and the
shooting screen reappears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
23
Adjusting the White Balance Manually (M.W.B.)
If none of the preset “ ”, “ ”, “ ” or “AUTO” positions can make the colours in the image look natural,
adjust the white balance manually to obtain the most suitable colour tones possible.
In step 4 on the previous page (੬ pg. 22),
1
2
select “MWB”.
Place a sheet of white paper about 1 ft.
(30 cm) in front of the lens.
•Place it so that the white paper fills the
screen.
Push the MENU Jog Dial.
3 •The setting is completed after about 1
second.
•The setting can be redone by pushing the
MENU Jog Dial again.
Rotate the MENU Jog Dial to select “EXIT”
4
and push it 3 times.
During indoor shooting . . .
.... the subject is exposed to a variety of light
sources, including outdoor light, fluorescent
light, candle light and so on. As the colour
temperatures of these light sources vary widely,
manual white balance adjustment is recom-
mended if you want to shoot images with the
most natural colour tones possible.
•The M.W.B. Setup Screen disappears and the
shooting screen reappears.
To return a manually-set white balance to an
automatically-set white balance . . .
.... select “AUTO” in step 4 in the procedure on
A
page 22 or turn the Power Dial to “ ”.
When the white balance is adjusted using coloured
paper . . .
.... in step 2, you can shoot images with a different
colour tone than when white paper is used.
NOTE:
The manually-set white balance is held in memory
until another balance value is set by selecting
“M.W.B.”.
Example:
When red paper is used:
The colours will be blue-greenish.
When blue paper is used:
The colours will be amberish.
When yellow paper is used:
The colours will be purplish.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SHOOTING (cont.)
24
EN
Shutter Speeds Selection
Selecting the Shutter Speed
The shutter speed of the camera can be selected manually, allowing a variety of expression in your pictures.
MENU Jog Dial
Power Dial
Look Button
LCD monitor
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
CAMERA
EXPOSURE
M .W. B .
SHUTTER
SPEED
SHUTTER SPEED
AUTO 1 / 100
0
AUTO
1 / 6
1 / 250
1 / 500
1 / 1000
EX I T
1 / 13
1 / 25
AUTO
EX I T
CAMERA MENU Screen
CAMERA Setup Screen
SHUTTER SPEED Setup Screen
NOTE:
Turn the Power Dial, while pressing its Lock
Button, to “M ” or “ ” and push the MENU
Jog Dial.
1
When you select a shutter speed of 1/13 sec. or less
(or 1/25 sec. or less when performing zoom or
close-up shooting), it is recommended that you use
a tripod to prevent blurring.
•The CAMERA MENU Screen appears.
Rotate the MENU Jog Dial to select
“CAMERA” and push it.
•The CAMERA Setup Screen appears.
2
3
4
Rotate the MENU Jog Dial to select
“SHUTTER SPEED” and push it.
•The SHUTTER SPEED Setup Screen appears.
Rotate the MENU Jog Dial to select the
desired shutter speed and push it twice.
•The shutter speed is selected and the
shooting screen reappears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
25
Shutter Speeds and Effects
Shutter Speed
Effect
AUTO
Automatically selects a shutter speed according to the subject lighting.
1/6 (sec.)
Suitable for shooting night views. Lights from moving cars, etc. are photographed with
motion streaks. Use a tripod to avoid blurring caused by subtle hand movements.
1/13 (sec.)
1/25 (sec.)
Suitable for shooting in darkly lit environments. A slow shutter speed can collect more
light in the camera than usual, and shoot bright, clear images of hard-to-shoot subjects
in low light. Use a tripod to avoid blurring caused by subtle hand movements.
Suitable for shooting in dimly lit environments (eg. rainy day). A slow shutter speed
can collect more light in the camera than usual, and shoot bright, clear images of
hard-to-shoot subjects in low light.
1/100 (sec.)
1/250 (sec.)
Suitable for shooting under outdoor lighting conditions such as a cloudy day.
Suitable for shooting under outdoor lighting conditions such as a sunny day. This
shutter speed is not affected by subtle hand movements.
1/500 (sec.)
1/1000 (sec.)
Suitable for shooting under outdoor lighting conditions such as by the seashore on a
sunny day. This shutter speed is not affected by subtle hand movements.
Allows fast-moving images to be captured one frame at a time. Use this shutter speed
under good lighting conditions.
NOTE:
If a high shutter speed is used under fluorescent lighting, hunting may occur in the image or the image
colour may be changed. This is not a malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SHOOTING (cont.)
26
EN
Manual Focusing
In contrast to auto focusing, where the camera automatically focuses on the subject, manual focusing can be
used when you want to intentionally change the point of focus in an image.
Shutter Release Button
FOCUS Dial
(MENU Jog dial)
Power Dial
Lock Button
CLEAR/FOCUS Button
LCD monitor
Turn the Power Dial, while pressing its Lock
Press the Shutter Release Button to shoot the
image.
M
1
2
Button, to “ ” or “ ”.
4
Press and hold the CLEAR/FOCUS Button for
about 2 seconds.
NOTE:
•“ ” and “ ” appear, and the focus can be
adjusted manually.
Manual focusing is recommended in the following
cases:
● When shooting a subject with low contrast
(variation in brightness/darkness), for example a
flat wall or blue sky.
● When there is an obstacle such as a mesh
between the camera and the subject.
● When the subject consists of a regular arrange-
ment of fine patterns or similar patterns.
● When shooting under a flickering light source
such as a fluorescent lamp.
Rotate the FOCUS Dial (MENU Jog Dial) to
focus the subject.
3
To focus on a farther subject . . .
Rotate the FOCUS Dial (MENU Jog Dial)
upward. When the focus level cannot be
adjusted any further, “ ” starts to blink.
To focus on a nearer subject . . .
Rotate the FOCUS Dial (MENU Jog Dial)
downward. When the focus level cannot be
adjusted any closer, “ ” starts to blink.
•2 focusing speeds are available. They can be
selected depending on how fast the FOCUS
Dial (MENU Jog Dial) is rotated. If the
FOCUS Dial (MENU Jog Dial) is rotated
quickly, the focus changes drastically. If the
FOCUS Dial (MENU Jog Dial) is rotated
slowly, the focus changes gradually.
To use auto focusing in the Manual mode (“M ”) . . .
.... press and hold the CLEAR/FOCUS Button for
about 2 seconds so that “ ” and “ ” disap-
pear.
Minimum subject distance:
The closest that this camera can focus on a subject,
with the zoom set all the way to “W”, is 7 cm.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
27
View Mode Selection
The Standard View mode displays a colour image on the LCD monitor, while the Quick View mode displays
a black-and-white image, but updates it more quickly to show the actual motion of the subject more
faithfully.
Power Dial
Lock Button
DISPLAY Button
M
A
Make sure that the Power Dial is set to “ ”, “ ” or “ ”, then press the DISPLAY Button.
1 •Each press of the DISPLAY Button switches the screen as shown below.
Standard View with
Information Display
mode (colour display)
Standard View mode
(colour display)
Quick View mode
(monochrome display)
Standard View mode
Quick View mode
A colour image is displayed on the LCD monitor
and is updated about 4 times a second. This mode
is suitable for shooting stationary subjects.
A black-and-white image is displayed on the LCD
monitor and is updated about 15 times a second.
This mode is suitable for shooting moving subjects.
• The image is stored in colour.
• The on-screen display is not available.
• When the shutter speed is set to 1/6 sec. or 1/13
sec., the Quick View mode is not available.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SHOOTING (cont.)
28
EN
Power Save Mode
The Power Save mode switches the camera automatically off when no operation has been performed for
more than 2 minutes.
MENU Jog Dial
Power Dial
Lock Button
LCD monitor
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
SYSTEM
POWER SAVE
FLASH ADJ .
DATE / T IME
EX I T
POWER SAVE
ON
OFF
EX I T
CAMERA MENU Screen
SYSTEM Setup Screen
POWER SAVE Screen
To deactivate the Power Save mode . . .
.... select “OFF” in step 4. When the Power Dial is
set to “A ”, “M ”, “ ” or “PLAY ”, the camera
power will stay on, even when no operations
are performed.
Turn the Power Dial, while pressing its Lock
Button, to “M ” or “ ” and push the MENU
Jog Dial.
1
•The CAMERA MENU Screen appears.
Rotate the MENU Jog Dial to select “SYSTEM”
and push it.
NOTES:
2
3
4
● To switch the camera on again after it has been
switched off by the Power Save mode, turn the
Power Dial to “OFF”, wait for more than 1 second,
then turn it to “ A ”, “ M ”, “ ” or “ PLAY ”.
● Do not forget to switch the camera off when not
in use, so that the batteries do not become
prematurely exhausted.
•The SYSTEM Setup Screen appears.
Rotate the MENU Jog Dial to select “POWER
SAVE” and push it.
•The POWER SAVE Screen appears.
Rotate the MENU Jog Dial to select “ON” and
push it twice.
● The Power Save mode is factory-preset to “ON”.
•The shooting screen reappears and the Power
Save mode is activated.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
29
Flash Adjustment
If an image shot with the flash is too dark or too bright, adjust the flash intensity as described below.
MENU Jog Dial
Power Dial
Lock Button
LCD monitor
CAMERA MENU
CAMERA
P I CTURE MODE
SYSTEM
EX I T
SYSTEM
POWER SAVE
FLASH ADJ .
DATE / T IME
EX I T
FLASH ADJ .
+2
EX I T
CAMERA MENU Screen
SYSTEM Setup Screen
FLASH ADJ. (Adjustment) Screen
Turn the Power Dial, while pressing its Lock
Rotate the MENU Jog Dial to select the flash
intensity and push it.
M
1
Button, to “ ” or “ ” and push the MENU
4
Jog Dial.
•Select from “0”, “–1”, “–2”, “+1” and “+2”.
•The CAMERA MENU Screen appears.
To brighten the flash (+1, +2) . . .
Rotate the MENU Jog Dial downward.
To darken the flash (–1, –2) . . .
Rotate the MENU Jog Dial upward.
Rotate the MENU Jog Dial to select “SYSTEM”
and push it.
2
3
•The SYSTEM Setup Screen appears.
Push the MENU Jog Dial twice.
Rotate the MENU Jog Dial to select “FLASH
ADJ.” and push it.
•The FLASH ADJ. (Adjustment) Screen
appears.
5 •The flash adjustment value is entered and the
shooting screen reappears.
NOTES:
● Aim the flash at the subject.
● Even when the flash intensity is increased, the
subject may not be properly lit, depending on the
shooting conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
30
EN
Playback Through a TV Monitor or VCR
By connecting the digital still camera to a TV monitor or VCR and starting playback, images can be
monitored on the TV screen or recorded onto a videotape.
TV
VCR
To VIDEO IN
To VIDEO IN
Video cable
(provided)
Core filter
Digital Still Camera
To VIDEO OUT
NOTES:
● For connections to a TV monitor or VCR, refer to their instruction manuals.
● The playback image can also be viewed on the LCD monitor of the camera without connecting it to a TV
monitor or VCR.
● During playback on a TV monitor, indications displayed in any of the shooting modes do not appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
31
Normal Playback
Auto Playback
Images shot with the camera are automatically
numbered, then stored in numerical order. You can
view the stored images, one at a time, much like
flipping through a photo album.
You can run through all the images stored in
memory automatically. This is like a regular slide-
show.
Zoom Button
W
T
Power Dial
Lock Button
Turn the Power Dial, while pressing its Lock
Turn the Power Dial, while pressing its Lock
PLAY
1
2
Button, to “PLAY ”.
1
2
Button, to “
”.
•The most recently photographed image is
displayed.
•The most recently photographed image is
displayed.
•If there are no images in memory, a blue
background is displayed on the screen.
Press and hold the Zoom Button for more than
3 seconds.
When there is more than one image in
memory:
Press the Zoom Button to view other images.
“T” : Displays images in ascending order.
“W” : Displays images in descending order.
Press the Zoom Button to stop Auto Playback.
“T” : Displays the next image.
“W” : Displays the previous image.
3 •Auto Playback can be stopped by pressing
either “T” or “W”.
NOTE:
Even if you shoot a new image after playing back a
low-numbered one, this will not overwrite an
existing image, because new images are automati-
cally stored after the last-recorded one.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (cont.)
32
EN
INDEX Screen
The images you shot can be displayed together with their index information. Convenient for checking
images shot beforehand, the INDEX Screen also shows the Picture Quality mode as well as which images
are protected against accidental erasure.
Selected image
INDEX
Index number
Picture Quality mode
Protect icon
001
F
002
005
S
F
006
F
004
F
001 to 999: Index number
F/S/E: Picture Quality mode
Since this camera can store up to 999 images using
a Compact Flash card, the index numbers range
from 001 to 999. For example, when 10 images are
stored (index number: 001 to 010), if three images
with index numbers 002, 004 and 006 are deleted
from memory, the remaining images are automati-
cally moved up to fill any gaps in the numerical
sequence. Therefore, the number of remaining
images is 7, and the new index numbers range from
001 to 007.
Displays the Picture Quality mode of the stored
image. There are 3 modes available: Fine (“F”),
Standard (“S”) and Economy (“E”) (in order of
quality).
: Protect icon
When an image is protected against its accidental
erasure, a padlock mark appears next to it, and that
image cannot be deleted.
When images are stored in both the built-in
memory and a Compact Flash card installed in the
camera, their index images and numbers are
different from those stored using only the built-in
memory.
Selected Image
An image is framed like this when it is selected.
Rotate the MENU Jog Dial to move the green frame
to the desired image.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
33
Index Playback
You can view all images stored in memory six at a time. Use this mode when looking for a image you wish
to view.
MENU Jog Dial
Power Dial
Lock Button
INDEX
001
F
002
005
S
F
003
006
E
F
LCD monitor
004
F
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
PLAY MODE
I NDEX
EFFECT
FRAME
MULT I
EX I T
INDEX Screen
.
MODE
PLAY MENU Screen
PLAY MODE Screen
NOTE:
Turn the Power Dial, while pressing its Lock
Button, to “PLAY ” and push the MENU Jog
Dial.
If no images are stored in memory, “PLAY MODE”
cannot be selected.
1
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “PLAY
MODE” and push it.
2
3
4
•The PLAY MODE Screen appears.
Rotate the MENU Jog Dial to select “INDEX”
and push it.
•The INDEX Screen appears.
Rotate the MENU Jog Dial to select the image
to be displayed and push it.
•The image selected in the INDEX Screen is
displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (cont.)
34
EN
Protecting Images
The Protect mode helps prevent the accidental erasure of images. Put a padlock mark next to the desired
image, and that image cannot be deleted.
MENU Jog Dial
Power Dial
LCD monitor
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
F I LE
PROTECT
DELETE
COPY
FORMAT
EX I T
Lock Button
.
MODE
PLAY MENU Screen
FILE Setup Screen
NOTE:
Turn the Power Dial, while pressing its Lock
Button, to “
Dial.
When the camera’s memory is initialized, even
protected images are deleted. If you do not want to
lose important images, transfer them to a PC and
save them.
PLAY
1
” and push the MENU Jog
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “FILE”
and push it.
2
3
•The FILE Setup Screen appears.
Rotate the MENU Jog Dial to select
“PROTECT” and push it.
•The PROTECT Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
35
INDEX
001
F
002
S
003
E
PRESS SHUTTER
AFTER SELECT
PROTECT Screen
To remove protection . . .
Rotate the MENU Jog Dial to select the image
to be protected (against accidental erasure)
and push it
Perform steps 1 through 3, then rotate the MENU
Jog Dial to select the desired padlocked image and
push it. The padlock mark located above the image
disappears and the image is no longer protected.
When finished unprotecting images, perform steps 5
and 6.
4
5
•A padlock mark appears on the selected
image to indicate that it is protected.
•Protect each image that you do not want to
delete by accident.
Press the Shutter Release Button.
Push the MENU Jog Dial twice.
6 •The screen returns to the normal playback
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (cont.)
36
EN
Deleting Images
Previously shot images can be deleted either one at a time or all at once.
MENU Jog Dial
Power Dial
LCD monitor
PLAY MENU
PLAY MODE
F I LE
F I LE
PROTECT
DELETE
COPY
FORMAT
EX I T
Lock Button
COMM
EX I T
.
MODE
PLAY MENU Screen
FILE Screen
Turn the Power Dial, while pressing its Lock
Button, to “
Dial.
Rotate the MENU Jog Dial to select “DELETE”
and push it.
•The DELETE Screen appears.
PLAY
1
2
” and push the MENU Jog
3
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “FILE”
and push it.
•The FILE Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
37
LCD monitor
LCD monitor
DELETE Screen
DELETE Screen
DELETE
ALL
DELETE
ALL
SELECTED
EX I T
SELECTED
EX I T
DELETE
001
DELETE
EXECUTE
EX I T
F
002
S
003
E
Delete Select
Screen
Deletion
Confirmation
Screen
PRESS SHUTTER
AFTER SELECT
To delete all images . . .
Before doing the following, perform steps 1 through
3 (੬ pg. 36).
DELETE
EXECUTE
EX I T
Rotate the MENU Jog Dial to select “ALL” and
4
5
push it.
•The Deletion Confirmation Screen appears.
Deletion Confirmation Screen
Rotate the MENU Jog Dial to select “EX-
ECUTE” and push it.
•“DELETING IN PROGRESS” is displayed until
all images have been deleted, which can take
from a few seconds to several minutes,
depending on the number of images stored.
•If “CONTAINS PROTECTED IMAGES” is
displayed, only the unprotected images will be
deleted.
To select an image by browsing images
stored in memory . . .
Before doing the following, perform steps 1 through
3 (੬ pg. 36).
Rotate the MENU Jog Dial to select
“SELECTED” and push it.
•When you also want to delete protected images,
unprotect them by referring to “To remove
protection” (੬ pg. 35) before deleting all the
images.
•If you do not want to delete the images, rotate
the MENU Jog Dial to “EXIT” and push it 4
times to return to the normal playback screen.
4
5
•The Delete Select Screen appears.
Rotate the MENU Jog Dial to select an image
to be deleted, and push it.
•“x” appears above the selected image.
•To abort deletion of a selected image, push the
MENU Jog Dial again. The “x” mark indicating
that the image is to be deleted disappears.
CAUTION
While protecting/unprotecting images, never remove
the Compact Flash card or disconnect power, as this
may cause the camera's built-in memory to be
Press the Shutter Release Button.
6 •The Deletion Confirmation Screen appears.
•If you want to abort deletion now, rotate the MENU
Jog Dial to select “EXIT” and push it 4 times.
corrupted. Also, be sure to use the optional AC power
adapter, as a malfunction may occur if the batteries
become exhausted halfway through the operation.
Rotate the MENU Jog Dial to select
NOTES:
7
“EXECUTE” and push it.
● A deleted image is lost forever. To prevent accidental
deletion of important images, it is recommended that
you protect them or copy them to your PC.
● If no images are stored in memory, “DELETE” cannot
be selected.
•The selected images are deleted and the normal
playback screen reappears.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (cont.)
38
EN
Applying Sepia/Black-and-White Effects
A sepia or black-and-white effect can be applied to a previously shot image.
MENU Jog Dial
Power Dial
Lock Button
LCD monitor
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
PLAY MODE
I NDEX
EFFECT
FRAME
MULT I
EX I T
EFFECT
BLACK /WH ITE
SEP I A
.
MODE
ZOOM
EX I T
PLAY MENU Screen
EFFECT Setup Screen
PLAY MODE Screen
Turn the Power Dial, while pressing its Lock
Button, to “PLAY ” and push the MENU Jog
Dial.
Rotate the MENU Jog Dial to select “BLACK/
WHITE” or “SEPIA” and push it.
1
4
•The image is displayed with the black-and-
white or sepia effect applied to it.
•The effect is applied to other displayed
images until it is canceled.
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “PLAY
MODE” and push it.
•The PLAY MODE Screen appears.
2
3
To cancel the effect . . .
.... press the CLEAR/FOCUS Button.
Rotate the MENU Jog Dial to select “EFFECT”
and push it.
•The EFFECT Setup Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
39
Magnifying the Playback Image (Zoom)
The zoom-in effect magnifies a selected area of image.
Power Dial
MENU Jog Dial
Lock Button
LCD monitor
EFFECT
BLACK /WH ITE
SEP I A
ZOOM
PLAY MENU
PLAY MODE
F I LE
PLAY MODE
EX I T
I NDEX
EFFECT
FRAME
MULT I
EX I T
EFFECT Setup Screen
COMM
EX I T
.
MODE
PLAY MENU Screen
PLAY MODE Screen
Turn the Power Dial, while pressing its Lock
Button, to “
Dial.
Rotate the MENU Jog Dial to select the area
to be magnified, and push it.
PLAY
1
” and push the MENU Jog
5
•The selected image is split into 9 areas, from
which you can select the area to be magni-
fied. By rotating the MENU Jog Dial, you can
reach the desired area as indicated above.
•The effect is applied to other displayed
images until it is canceled.
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “PLAY
MODE” and push it.
•The PLAY MODE Screen appears.
2
3
4
Rotate the MENU Jog Dial to select “EFFECT”
and push it.
To cancel the effect . . .
.... press the CLEAR/FOCUS Button.
•The EFFECT Setup Screen appears.
Rotate the MENU Jog Dial to select “ZOOM”
and push it.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (cont.)
40
EN
Types of Frames
An image can be displayed in 9 types of frames. The framed image can be printed out by transmitting the
image data with the frame data to a printer. Frames can also be used in 4-split or 16-split screens.
Preset frames (9 types)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
41
Framing an Image
MENU Jog Dial
Power Dial
LCD monitor
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
PLAY MODE
I NDEX
EFFECT
FRAME
MULT I
EX I T
Lock Button
.
MODE
PLAY MENU Screen
FRAME Setup Screen
NOTE:
Turn the Power Dial, while pressing its Lock
Button, to “
Dial.
PLAY
Frames can also be used in 4-split or 16-split
1
” and push the MENU Jog
screens (੬ pg. 42).
•The PLAY MENU Screen appears.
To remove a frame . . .
.... press the CLEAR/FOCUS Button.
Rotate the MENU Jog Dial to select “PLAY
MODE” and push it.
2
3
4
•The PLAY MODE Screen appears.
Rotate the MENU Jog Dial to select “FRAME”
and push it.
•The FRAME Setup Screen appears.
Rotate the MENU Jog Dial to select a frame
and push it.
•The selected image is displayed inside the
frame.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (cont.)
42
EN
Multi-Image Screen
Multi-image screens that can be created are 4-split screens composed of the same image, 16-split screens
composed of the same image and 4-split screens composed of different, user-selected images.
MENU Jog Dial
Power Dial
LCD monitor
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
PLAY MODE
I NDEX
EFFECT
FRAME
MULT I
EX I T
Lock Button
.
MODE
PLAY MENU Screen
PLAY MODE Screen
Turn the Power Dial, while pressing its Lock
Button, to select “
Jog Dial.
Rotate the MENU Jog Dial to select “MULTI”
and push it.
•The MULTI Setup Screen appears.
•While a multi-image screen is being
displayed, it is impossible to select the
MULTI Setup Screen from the PLAY MODE
Screen. If you wish to select the MULTI Setup
Screen, first press the CLEAR/FOCUS Button
to return to the normal playback screen, then
perform steps 1 through 3.
PLAY
1
2
” and push the MENU
3
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “PLAY
MODE” and push it.
•The PLAY MODE Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
43
MUL T I
MUL T I
SAME
4
SELECTED
SAME 16
EX I T
SAME
4
SELECTED
SAME 16
EX I T
4
4
MULTI Setup Sreen
MULTI Setup Sreen
Multi-image screen
Multi-image screen
To Create a Multi-Image Screen Using
Selected Images
To Create a Multi-Image Screen Using
the Same Image
Before doing the following, perform steps 1 through
3 (੬ pg. 42).
Before doing the following, perform steps 1 through
3 (੬ pg. 42).
Rotate the MENU Jog Dial to select
Rotate the MENU Jog Dial to select “SAME 4”
4
5
“SELECTED 4” and push it.
4
or “SAME 16” and push it.
•The MULTI Index Screen appears.
•A multi-image screen displaying 4 or 16 of
the same image appears.
Rotate the MENU Jog Dial to select an image
and push it.
NOTES:
•“
ߛ ” appears on the selected image. ● By printing a multi-image screen to a printer that
supports sticker sheets, you can create stickers of
any image you like. For details, read the instruc-
tion manual of your printer.
To cancel the selection of an image . . .
... rotate the MENU Jog Dial to select the
image and push it. “
ߛ ” disappears. ● To create a multi-image screen with frames, first
select a frame, referring to “Framing an image”
(੬ pg. 41), then make a multi-image screen.
Repeat step 5 for all 4 images to be selected.
6 •The selected images are displayed in the
order they were selected in steps 5 and 6.
•A multi-image screen of the selected images
appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLIED OPERATIONS
Removing a Compact Flash Card
As a Compact Flash card retains images in its
memory even after it has been removed from the
camera, it can also be used as a medium for storing
images.
44
EN
Compact Flash Card Operation
Installing a Compact Flash Card
A Compact Flash card increases the number images
that can be stored.
NOTES:
NOTES:
● Switch the camera off with the Power Dial before
installing a Compact Flash card.
● Switch the camera off with the Power Dial.
● Do not remove the Compact Flash card while the
camera is turned on, as this may cause the
Compact Flash card or the camera's built-in
memory to be corrupted.
● Point the marking on the bottom of the camera
and the one on the Compact Flash card upward,
then point the marking on the Compact Flash
card at the camera and install straight in.
Align both markings.
Press EJECT
Jack cover
Bottom panel
of the camera
Compact Flash card
Lock Button
Power Dial
DISPLAY Button
Install the Compact Flash card in the slot.
1 •Insert the Compact Flash card so that it fits
Open the jack cover and press the EJECT
securely in position.
1
2
Button on the bottom of the camera.
The following steps 2 and 3 are intended to
check that the Compact Flash card is
installed securely.
•The Compact Flash card is disengaged from
the camera.
Pull out the Compact Flash card.
Turn the Power Dial, while pressing its Lock
2
Button, to “ A ” or “M ”.
Press the DISPLAY Button.
3 •The Information Display Screen appears.
NOTES:
CF
•If the (Compact Flash card) icon appears on
● Be sure to use only Compact Flash cards bearing
the CF trademark ( ).
the top left of the screen, images shot hereafter
will be stored in the Compact Flash card.
● Some brands of Compact Flash cards are not
compatible with this camera. Before purchasing a
Compact Flash card, consult its manufacturer or
dealer.
NOTE:
CF
If the
icon does not appear on the top left of the
screen after the Compact Flash card has been installed,
switch the camera power off, remove the card and
install it again.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
45
Initializing the Storage Media
Since the camera is a microcomputer-controlled device, external noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. For example, when a still image you shot is stored in
memory, the above may cause the following: Although the remaining number of shots indicator shows that
shooting is possible, a still image cannot be stored in memory after shooting.
In such a case, initialize the memory by following steps 1 through 4 below. Please note that initialization
deletes all the still images (including ones for which you performed the “Protect” function) stored in
memory. If you wish to keep any of the still images that are stored in memory, before initialization first
transfer them to a PC and save them. If image data is corrupt, transfer is impossible. Normally, it is not
necessary to initialize a Compact Flash card. However, if a malfunction occurs (for example, if the image
you shot cannot be played back), then initialize the Compact Flash card.
NOTE:
Switch the camera off with the Power Dial before installing a Compact Flash card.
Preparation
Turn the Power Dial, while pressing its Lock
Button, to “
Dial.
Insert the Compact Flash card to be initialized.
PLAY
1
2
” and push the MENU Jog
•The PLAY MENU Screen appears.
PLAY MENU Screen
Power Dial
Rotate the MENU Jog Dial to select “FILE”
and push it.
OFF
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
Y
A
•The FILE Screen appears.
Rotate the MENU Jog Dial to select
“FORMAT” and push it.
.
MODE
Lock Button
3
4
Rotate the MENU Jog Dial to select
“EXECUTE” and push it.
•The message “FORMATTING IN PROGRESS”
is displayed and formatting starts.
•When “NO IMAGES STORED” is displayed,
formatting is complete.
F I LE
PROTECT
DELETE
COPY
MENU Jog Dial
FILE Screen
FORMAT
EX I T
CAUTION
● Do not perform any other operation (such as
turning off the camera) during initialization,
as this may cause the camera's built-in
memory to be corrupted. Also, be sure to use
the optional AC power adapter, as the
camera’s built-in memory or the Compact
Flash card may be corrupted if the batteries
become exhausted during initialization.
● If the built-in memory is initialized, the preset
frames (੬ pg. 40) will be lost. If this occurs,
consult your nearest JVC dealer. It is still
possible to shoot and play back images
without the preset frames.
FORMAT
EXECUTE
EX I T
FORMAT Screen
NOTES:
● After initializing, all images stored in the compact flash card, including those which have been protected,
are cleared. Be sure to transfer important images to a PC before proceeding with initialization. However, if
image data is corrupt, it cannot be transferred to a PC.
● Initializing a Compact Flash card does not clear images stored in the camera’s built-in memory.
● If the message “PLEASE INITIALIZE” appears, the built-in memory needs to be initialized. Without inserting
a Compact Flash card, perform steps 1 through 4.
● When a Compact Flash card is not installed, “FORMAT” normally cannot be selected. If it can be selected,
then the built-in memory is malfunctioning. When this occurs, make a back-up of the stored image data
before initializing.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLIED OPERATIONS (cont.)
Playing Back Images Stored in a
Compact Flash Card
46
EN
Storing Images in a Compact Flash
Card
The number of images that can be shot can be
greatly increased when a Compact Flash card is
used in addition to the built-in memory. By
preparing several cards, a single camera can be
shared by several people, or they can be used to
make a library of images sorted by category.
NOTE:
Switch the camera off with the Power Dial before
installing or remoing a Compact Flash card.
NOTE:
Switch the camera off with the Power Dial before
installing or removing a Compact Flash card.
CF
CF
F I NE
0 0 1
0 0 1
Install the Compact Flash card in the camera.
Turn the Power Dial, while pressing its Lock
Install the Compact Flash card in the camera.
1
2
1
2
Turn the Power Dial, while pressing its Lock
A
M
Button, to select “ ”, “ ” or “ ”.
PLAY
Button, to select “
”.
CF
•Press the DISPLAY Button to make sure the
(Compact Flash card) icon appears in the
Information Display Screen.
CF
•Press the DISPLAY Button to make sure the
(Compact Flash card) icon appears in the
Information Display Screen.
Shoot images.
Play back images.
3 •The images are automatically stored in the
3 •The images stored in the Compact Flash card
Compact Flash card.
can be played back.
NOTES:
NOTE:
● To store images in the camera’s built-in memory,
switch off the camera and remove the Compact
Flash card from the camera. See “Removing a
Compact Flash Card” (੬ pg. 44).
To play back images stored in the camera’s built-in
memory, switch off the camera and remove the
Compact Flash card from the camera. See “Remov-
ing a Compact Flash Card” (੬ pg. 44).
● To prevent the accidental erasure of images stored
in a Compact Flash card, transfer them to a
Windows® PC or Macintosh® and save them. We
also recommend that you regularly copy images
stored in a Compact Flash card to the camera's
built-in memory during shooting.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK (Cont.)
EN
47
Copying Images Between the Built-in Memory and a Compact Flash Card
Images can be copied from the built-in memory to a compact flash card or vice versa. This function can be
used to store especially important images separately or to exchange images.
NOTE:
Switch the camera off with the Power Dial before installing or removing a Compact Flash card.
MENU Jog Dial
Power Dial
Lock Button
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
F I LE
PROTECT
DELETE
COPY
FORMAT
EX I T
COPY
CAMERA CARD
CARD CAMERA
EX I T
.
MODE
PLAY MENU Screen
COPY Screen
FILE Screen
Install the Compact Flash card in the camera.
Rotate the MENU Jog Dial to select “COPY”
and push it.
•The COPY Screen appears.
1
2
4
5
Turn the Power Dial, while pressing its Lock
PLAY
Button, to “
Dial.
” and push the MENU Jog
Rotate the MENU Jog Dial to select
“CAMERA ¥ CARD” or “CARD ¥ CAMERA”
and push the MENU Jog Dial.
•The COPY Setup Screen appears.
To copy selected images only . . .
Go to step 6 on page 48.
•The PLAY MENU screen appears.
Rotate the MENU Jog Dial to select “FILE”
and push it.
3
•The FILE Screen appears.
To copy all images . . .
Go to step 6 on page 49.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLIED OPERATION (cont.)
48
EN
To Copy Selected Images Only
Before doing the following, perform steps 1 through 5 on page 47.
COPY
ALL
SELECTED
EX I T
COPY
EXECUTE
EX I T
COPY Screen
Copy Confirmation Screen
Shutter Release Button
Rotate the MENU Jog Dial to select
“SELECTED” and push it.
After selecting all the images to be copied,
press the Shutter Release Button.
6
7
8
9
•The INDEX Screen appears.
•The Copy Confirmation Screen appears.
Rotate the MENU Jog Dial to select an image
to be copied and push it.
•“
ߛ ” appears on the selected image. •Repeat this procedure until every image you
wish to copy is selected.
Rotate the MENU Jog Dial to select
“EXECUTE” and push it.
•The message “IMAGE COPYING IN
PROGRESS” is displayed, and copying starts.
When the message disappears, copying is
complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
49
To Copy All Images
Before doing the following, perform steps 1 through 5 on page 47.
Rotate the MENU Jog Dial to select “ALL” and
push it.
6
7
COPY
ALL
SELECTED
EX I T
•The Copy Confirmation Screen appears.
Rotate the MENU Jog Dial to select
“EXECUTE” and push it.
•The message “IMAGE COPYING IN
PROGRESS” is displayed, and copying starts.
When the message disappears, copying is
complete.
COPY Screen
NOTES:
COPY
EXECUTE
EX I T
● While copying, never disconnect the power
supply or remove the Compact Flash card, as this
may cause the stored images to be erased or the
camera's built-in memory to be corrupted. Also,
be sure to use the optional AC power adapter, as
the camera’s built-in memory or the Compact
Flash card may be corrupted if the batteries
become exhausted during the copy operation.
● If 5 images stored in a Compact Flash card are
copied to the built-in memory, which contains 10
stored images, the index numbers of the copied
images will be from 11 to 15.
Copy Confirmation Screen
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLIED OPERATION (cont.)
50
EN
Image Copy Using Infrared Communication [IrTran-P]
Image data can be copied between this camera and another piece of IrDA (IrTran-P) infrared communication
compatible equipment, regardless of its manufacturer.
MENU Jog Dial
Power Dial
FLASH/TRANSFER Button
Lock Button
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
COMM
.
MODE
PC MODE
I R MODE
EX I T
.
MODE
PLAY MENU Screen
COMM. MODE Setup Screen
Turn the Power Dial, while pressing its Lock
Button, to “PLAY ” and push the MENU Jog
Dial.
Rotate the MENU Jog Dial to select “IR
MODE” and push it twice.
1
2
3
•The normal playback screen reappears.
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “COMM.
MODE” and push it.
•The COMM. MODE Setup Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
51
Position the transmitting and receiving
equipment so that their infrared transmitter
and receiver face opposite each other.
4
5
IrTran-P infrared
communication
compatible equipment
•The distance between them should be less
than 50 cm, and the transmitter and receiver
should be angled no more than 15° to each
other.
If the camera is the transmitting equipment,
press the FLASH/TRANSFER Button.
•The message “TRANSMISSION IN
PROGRESS” is displayed, and image transfer
starts.
•During image transfer, only one image should
be displayed. If a menu screen or index
screen is displayed, transfer is impossible.
•If the message “TRANSMISSION FAILED” is
displayed 30 seconds after the FLASH/
TRANSFER Button is pressed, check the
equipment orientation, power supplies, etc.
and retry the transfer.
15°
15°
15°
15°
< 50 cm
•To abort transfer in the middle, press the
CLEAR/FOCUS Button. The message
“TRANSMISSION TO BE STOPPED” is
displayed.
If the camera is the receiving equipment, the
message “RECEPTION IN PROGRESS” is
displayed.
6
•Reception is complete when this message
disappears.
•If the message “RECEPTION FAILED”
appears, check the equipment orientation,
power supplies, etc. and retry the transfer.
•To abort transfer in the middle, press the
CLEAR/FOCUS Button.
•Image data is received in the “FINE” Picture
Quality mode.
•It is recommended that you use the optional
AC power adapter during data transfer.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLIED OPERATION (cont.)
52
EN
Printing on a Digital Printer [IrDA Transfer]
Selected images can be transferred without using a cable to a digital printer that supports infrared communi-
cation (IrTran-P), such as the JVC GV-DT1 and GV-HT1, for printing.
Preparation
The distance between the digital still camera’s IR transmitter and the digital printer’s IR receptor should be
less than about 50 cm. When sending data, the transmitter should be no more than 15 degrees to the left or
right of the printer’s IR receptor.
Turn the Power Dial, while pressing its Lock
1
2
3
Button, to “PLAY ”.
Zoom Button
Select the image(s) to be printed by pressing
the Zoom Button or using the INDEX Screen.
Push the MENU Jog Dial to make the PLAY
MENU Screen appear. Rotate the MENU Jog
Dial to select “COMM. MODE” and push it.
Next, rotate the MENU Jog Dial to select “IR
MODE” and push it.
Process the selected image(s) as desired.
4 •You can add effects and frames, as well as
make multi-image screens, when processing
images.
Press the FLASH/TRANSFER Button.
5 •The message “TRANSMISSION IN
PROGRESS” is displayed and image transfer
to the printer starts.
•After the transfer is complete, perform the
print operation on the printer. If you use a
printer which starts printing automatically,
simply wait for it to begin.
To abort image transfer in the middle . . .
.... press the CLEAR/FOCUS Button. The message
“TRANSMISSION TO BE STOPPED” is
displayed.
FLASH/TRANSFER Button
NOTES:
● If the message “TRANSMISSION FAILED” is displayed 30 seconds after the FLASH/TRANSFER Button is
pressed, check equipment orientation, power supplies, etc. and retry the transfer.
● Image data transfer via IrDA communication is possible only between one transmitter and one receiver. If
you attempt to transfer image data from a single digital still camera to more than one digital printer, only
the printer answering first will receive and print the image data.
● IrTran-P (Infrared Transfer Picture): This is an infrared image data communication standard. Equipment in
compliance with this standard can exchange image data using IR rays regardless of their manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
53
PC Connection Operation
Picture Navigator Software (Provided)
Image data in the camera can be sent to the RS-232C port of a Windows® PC or to the modem port of a
Macintosh® or Mac OS-compatible computer.
NOTE:
Also read the instruction manuals of the provided “Picture Navigator” software.
PLAY MENU
PLAY MODE
F I LE
COMM
EX I T
COMM
.
MODE
PC MODE
I R MODE
EX I T
.
MODE
PLAY MENU Screen
COMM. MODE Setup Screen
Connect the PC jack of the camera to the
computer’s RS-232C port (Windows®), or to
its modem or printer port (Macintosh®).
Rotate the MENU Jog Dial to select “PC
MODE” and push it twice.
1
5
6
•The normal playback screen reappears.
Install the Picture Navigator software on your
computer.
On the computer, capture the desired images
and process them.
2
3
•The message “PC MODE” appears during
image transfer.
•We recommend turning the camera off after
transferring images.
Turn the Power Dial, while pressing its Lock
PLAY
Button, to “
Dial.
” and push the MENU Jog
•The PLAY MENU Screen appears.
Rotate the MENU Jog Dial to select “COMM.
MODE” and push the MENU Jog Dial.
NOTES:
4
● During image transfer to the computer, only one
image should be displayed. If a menu screen or
index screen is displayed, transfer is impossible.
● Before transferring image data from the computer
to this camera, be sure to select the “FINE”
Picture Quality mode, referring to “Picture Mode
Selection” (੬ pg. 15).
•The COMM. MODE Setup Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS, CONNECTORS AND INDICATORS
54
EN
2 4
1
3
5
6
8
Lock button
PC
7
9
0
!
^
&
@
#
%
$
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
55
Front View
Rear View
1 Shutter Release Button ..............੬ pg. 12
8 Power Dial............................... ੬ pg. 14
Press when you wish to shoot.
Turn while pressing its Lock Button to
select a shooting mode or the playback
mode.
2 Flash........................................ ੬ pg. 20
Lights when shooting under low light or
back light conditions.
3 Flash Sensor .............................੬ pg. 20
9 Zoom Button...................... ੬ pg. 18, 31
Press to zoom during shooting or to switch
to the next/previous image during play-
back.
Be careful not to cover this area when
using the flash.
0 MENU/BRIGHT/FOCUS
4 Infrared Beam Sensor ............... ੬ pg. 51
Jog Dial ........................ ੬ pg. 10, 13, 26
Transmits/receives image data via infrared
beam.
5 Lens ........................................ ੬ pg. 12
Turn to adjust settings for shooting or
playback, to adjust the brightness of the
LCD monitor or to adjust the focus.
Train on the subject.
! BATTERY Cover .......................... ੬ pg. 8
Open to replace the batteries.
@ CLEAR/FOCUS Button .............. ੬ pg. 26
6 Self-Timer Lamp ....................... ੬ pg. 19
Blinks when the Self-Timer is activated.
7 PC Jack
Press to cancel an effect or to focus on a
subject manually.
Connect to the RS-232C port (Windows®)
or to the modem or printer port
# DISPLAY Button ....................... ੬ pg. 17
(Macintosh®) of your computer.
Press to make the on-screen display
appear/disappear during playback, or to
cycle through the Standard View mode, the
Standard View with Information Display
mode or the Quick View mode while
shooting.
$ Flash Lamp............................... ੬ pg. 20
Lights when the flash is ready.
% FLASH/TRANSFER Button ... ੬ pg. 20, 50
Press to transfer images by infrared beam
or to charge the flash.
^ VIDEO OUT Jack ..................... ੬ pg. 30
Connect to a VCR, TV monitor or video
& DC-IN Jack ................................ ੬ pg. 9
Connect to the optional AC power adapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN CONTROLS, CONNECTORS AND INDICATORS (cont.)
56
1
2
3
4
5
Bottom View
1 EJECT Button............................ ੬ pg. 44
4 Compact Flash Card Slot ........... ੬ pg. 44
Insert an optional Compact Flash card.
5 Reset Switch
Press to eject the optional Compact Flash
card.
2 Tripod Mounting Socket
Allows you to reset the camera to its
factory presets. First, remove the power
supply (AC power adapter, batteries, etc.),
then insert a pin or similar object into this
hole.
When attaching a tripod, insert the
threaded section of the tripod in this hole
and turn to secure. Use only tripods not
equipped with a stud that prevents the
camera from rotating.
3 Hand Strap Eyelet .......................੬ pg. 8
Thread the provided hand strap through
this eyelet.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
57
On-Screen Display During Shooting
M
When the Power Dial is set to “ A ”, “ ” or “ ”, press the DISPLAY Button to change the View mode.
Each press of the DISPLAY Button switches the screen as shown below.
Standard View with
Information Display mode
(colour display)
Standard View mode
(colour display)
Quick View mode
(monochrome display)
1 2 3 4 5
CF
F I NE
0 2 1 / 0 3 0
1 / 1 0 0 0
+
2
6
7
9
0
!
2 7 . 1 2 . 1 9 9 8
1 4 : 0 5 : 2 3
@
#
8
CF
8 Battery Power Remaining
1
Icon ..................................... ੬ pg. 46
Displays the approximate battery power
remaining:
Appears when images are being stored in a
Compact Flash card.
2 Picture Quality Mode ............... ੬ pg. 15
9 White Balance.......................... ੬ pg. 22
Displays the selected Picture Quality mode
(FINE/STD/ECONOMY).
Displays the current setting when any
white balance except AUTO is selected
(Fine “ ”/Cloudy “ ”/Halogen“ ”/
Manual White Balance “M.W.B.”).
3 Shutter Speed........................... ੬ pg. 24
4 Number of Shots Taken
0 Flash Icon ................................ ੬ pg. 20
Shows the number of images that have
already been shot.
Appears when the flash is charged.
! Low Light Icon ......................... ੬ pg. 20
5 Total Number of Shots
Appears when the flash is required.
Displays the total number of shots that can
be stored, including those already taken.
6 Exposure Value......................... ੬ pg. 21
@ Date Display (Day/Month/Year) ... ੬ pg. 10
# Time Display ............................ ੬ pg. 10
7 Focus Indicator ........................੬ pg. 26
Indication During Self-Timer
Mode........................................... ੬ pg. 19
: Appears when the Power Dial is set to “ ”.
When the Shutter Release Button is pressed, this
indicator blinks and the Self-Timer is activated.
Displays manual focusing adjustments.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENCONTROLS, CONNECTORS AND INDICATORS (Cont.)
On-Screen Display During Shooting (cont.)
58
1 2
3
4
CF
F I NE
0 0 1
5
Information Displayed Between Shutter
Release and Storage of Image in Memory
Icons Displayed During Manual Focusing
These icons are displayed when manual focusing is
selected.
CF
1
Icon ..................................... ੬ pg. 46
4 Far .......................................... ੬ pg. 26
Appears when the image is stored in a
Compact Flash card.
Rotate the FOCUS Dial (MENU Jog Dial)
upward to focus on a farther subject. When
rotating the FOCUS Dial (MENU Jog Dial),
is displayed.
2 Picture Quality Mode (FINE/STD/
ECONOMY) ............................. ੬ pg. 15
5 Near........................................ ੬ pg. 26
Rotate the FOCUS Dial (MENU Jog Dial)
downward to focus on a nearer subject.
When rotating the FOCUS Dial (MENU Jog
Dial), is displayed.
3 Image Number
Displays the index number given to the
image file.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
59
On-Screen Display During Playback
When the Power Dial is set to “PLAY ”, press the DISPLAY Button to view the information display over the
playback screen.
Each press of the DISPLAY Button switches the screen as shown below.
Playback image and
information display
Playback image
1 2
3 4
CF
F I NE
0 2 1 / 0 3 0
2 7 . 1 2 . 1 9 9 8
1 4 : 0 5 : 2 3
5
7
6
CF
1
Icon ..................................... ੬ pg. 46
5 Date ........................................ ੬ pg. 10
6 Time ........................................ ੬ pg. 10
7 Battery Power Remaining
Appears when an image stored in a
Compact Flash card is played back.
2 Picture Quality Mode................ ੬ pg. 15
Displays the approximate battery power
remaining.
Displays the Picture Quality mode used for
the image.
3 Image Number
Displays the index number given to the
image file.
4 Total Number of Images
Displays the total number of stored images.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
As this digital still camera is controlled by a microcomputer, it may occasionally malfunction due to noise or
interference. In such a case, remove the power supply (batteries or AC power adapter), push the Reset
Switch (੬ pg. 56) and retry using the camera. If the trouble still persists and it cannot be solved by referring
to the following table, please consult your nearest JVC dealer.
60
EN
SYMPTOM
CORRECTIVE ACTION
PAGE
Power
No power is supplied.
● Is the battery dead?
● Are the batteries loaded in the correct direction?
● Is the power supply connected properly?
8
9
Shooting
The LCD monitor flickers in the
Standard View mode (colour
display).
● The battery power is low. Replace the batteries.
8
Shooting is impossible.
● Is the Power Dial set to “PLAY ”?
14
14
14
Images do not appear.
● Switch off the camera, then on again.
A
The menu screens are not available.
● Is the Power Dial set to “ ”?
Although the Shutter Release Button
is half-pressed, focusing is not
possible.
● Is focusing set to manual adjustment?
● Are you shooting under low light or are you
shooting a subject which has no contrast?
26
Images become dark when sunlight
is captured by the camera.
● This is not a malfunction.
—
The LCD monitor is dark or whitish.
● Turn the lens to adjust the LCD monitor angle or
adjust the brightness.
12
● Is the image being played back in a cold place?
In cold areas, the LCD monitor appears slightly
dark. This is not a malfunction.
● The LCD monitor's lamp is reaching the end of
its service life. Consult your nearest JVC dealer.
The message “MEMORY FULL”
appears.
● When the built-in memory is full and no more
shooting is possible, this message appears. Use a
blank Compact Flash card or transfer the stored
images to a Windows® PC or Macintosh® and
save them. Then, delete the images from the
camera's built-in memory to make room for new
shots.
47–53
36
Images take on a strobe-like effect.
There is colour noise in the image.
● This is not a malfunction.
● This is not a malfunction.
—
—
During flash shooting, power turns
off.
● During flash shooting, if the remaining battery
power is half-full or less, the power may turn off.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
61
SYMPTOM
CORRECTIVE ACTION
PAGE
Others
The image on the LCD monitor
appears distorted.
● Is the surface or the edge of the LCD monitor
being pressed? If so, release your hand and
leave it for a while.
—
The date/time is not displayed
properly.
● The remaining power of the built-in clock
battery is close to nil. Connect the camera to the
AC power adapter and plug it in for over 24
hours.
9
A Compact Flash card cannot be
inserted.
● Is the Compact Flash card being held in the
correct direction?
44
None of the buttons or controls
function on the camera.
● Switch the camera off, remove the power supply
(battery or AC power adapter) and press the
Reset Switch on the bottom of the camera with a
pin or similar object. All settings are returned to
their factory presets.
9
56
Small coloured or black spots
appear on the LCD monitor.
● The LCD monitor is manufactured using high-
precision technology, however, a few pixels on
it may be always off (black) or on (lit). This is
not due to any defect of the camera. (Function-
ing dots: more than 99.99%)
—
Preset frame images do not appear.
● If the built-in memory is initialized after the
message “PLEASE FORMAT” appears, the preset
frames are erased. Consult your nearest JVC
dealer.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY AND MESSAGES
62
EN
Display
Description
NO IMAGES STORED
● Appears during playback when no images are stored in the
built-in memory or Compact Flash card.
CONTAINS PROTECTED IMAGES
● Appears when there are protected images in the camera when
all-image deletion is attempted. In this case, all images can be
deleted by unprotecting the protected images.
TRANSMISSION IN PROGRESS
RECEPTION IN PROGRESS
TOO MANY COPIES
● Appears while the camera is transmitting image data via the IR
communication system.
● Appears while the camera is receiving image data via the IR
communication system.
● Appears when copying is impossible because there is not
enough space at the destination. Either make space at the
destination or reduce the number of images to be copied.
IMAGE COPYING IN PROGRESS
FORMATTING IN PROGRESS
● Appears while image data is being copied.
● Appears while a Compact Flash card or the built-in memory is
being initialized.
TRANSMISSION TO BE STOPPED
RECEPTION TO BE STOPPED
TRANSMISSION FAILED
RECEPTION FAILED
● Appears when image transmission is cancelled.
● Appears when image reception is cancelled.
● Appears when data was not sent due to failure.
● Appears when data was not received due to failure.
● Appears during image transmission through a PC connection.
● Appears while the camera is deleting images.
PC MODE
DELETING IN PROGRESS
PLEASE INITIALIZE
● Appears when a malfunction occurs in the built-in memory.
When this appears, initialize the built-in memory.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
EN
63
AC Power Adapter (Optional)
Batteries
•This camera requires 4 LR6 (AA)-size alkaline
batteries. LR6 (AA)-size nickel-cadmium (Ni-Cd)
or nickel-metal hydrode (Ni-MH) batteries can
also be used. Note that the battery power
remaining indicated by the camera does not take
the type of batteries being used into account.
•Do not use manganese batteries as they do not
have sufficient energy to power this camera.
•Use the batteries properly. The wrong use can
cause them to leak, or become hot or damaged.
When replacing the batteries, insert them with
their (+) and (–) polarity marks properly aligned, as
indicated by the orientation marking inside the
battery cover.
•When the batteries become cold in cooler
temperatures (below 10 °C), such as outdoors in
winter, their lifetime shortens and they may cease
to function. If this happens, place the batteries in
your pocket or other warm, protected place for a
short time, then re-insert them in the camera. We
recommend using LR6 (AA)-size nickel-cadmium
batteries as they can power the camera even at
0°C.
1. To prevent fire, electric shock or injury...
.... DO NOT use the AC power adapter with any
power source or voltage not supported.
.... DO NOT modify or disassemble the AC
power adapter. Never attempt to repair or
check it yourself, as this is very dangerous.
Consult your nearest JVC dealer for mainte-
nance on the AC power adapter.
.... DO NOT connect any power cord other than
the one provided to the AC power adapter. If
the power cord's performance or design is
different, fire or electric shock may result.
.... first connect the power cord to the AC power
adapter. If the power cord is connected first
to an AC outlet, and the AC power adapter's
connector comes in contact with a metallic
object, a short-circuit will occur which may
result in fire or injury.
2. To prevent fire, malfunction or electric
shock...
.... DO NOT use any AC power adapter except
the one specified with this digital still
camera. If the AC adapter's performance or
design is different than what the digital
camera is designed for, fire, malfunction or
electric shocks may result. Before using,
thoroughly read the instructions of the digital
still camera and the AC power adapter.
•If the (+) and (–) polarity marks are dirty with
sweat or oil, this will cause contact failure. Wipe
them off with a dry cloth, then use the batteries.
•Keep new batteries handy if you plan to use the
camera for an extended period of time (for travel,
etc.).
3. To avoid malfunction...
•Before using Ni-Cd or Ni-MH batteries, be sure to
charge them fully using their designated battery
charger.
•Since batteries become hot after they are ex-
hausted, be careful when replacing them with
new ones.
.... connect the power cord to the AC power
adapter securely. If the power cord is
disconnected during use of the camera,
shooting or playback may become impossi-
ble and the image data may become corrupt.
•If the batteries are not used for an extended
period, remove them from the camera to avoid
battery leakage, which can cause malfunctions to
occur.
•Do not use different kinds of batteries or old and
new batteries together.
•Do not expose the batteries to excessive heat, as it
may cause them to leak or explode.
•Do not dispose of batteries in fire.
•Do not shortcircuit the terminals. Keep them away
from metallic objects when not in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
64
EN
Built-in Rechargeable Battery
Main Unit
To store the date/time in memory, a rechargeable
battery is integrated in the camera. As long as the
camera is connected to an AC outlet using the AC
power adapter, or the batteries installed in the
camera continue to supply power to the camera, the
built-in battery is always charged. However, if the
camera is not used for approx. 3 months, the built-
in battery will become discharged and the date/time
stored in memory will be lost. When this occurs,
connect the camera to an AC outlet using the AC
power adapter for over 24 hours to charge the built-
in rechargeable battery. Before using the camera
again, set the date/time.
1. For safety, DO NOT . . .
.... open the camera’s chassis.
.... disassemble or modify the unit.
.... allow inflammables, water or metallic objects
to enter the unit.
.... remove the batteries or disconnect the power
supply while the power is on.
2. Avoid using the unit . . .
.... in places subject to excessive humidity or
dust.
.... in places subject to soot or steam such as
near a cooking stove.
.... in places subject to excessive shock or
vibration.
.... near a television set.
Note that it is possible to use the camera without
setting the date/time.
.... near appliances generating strong magnetic
or electric fields (speakers, broadcasting
antennas, etc.).
.... in places subject to extremely high (over
40°C) or extremely low (under 0°C) tempera-
tures.
3. DO NOT leave the unit . . .
.... in places of over 50°C.
.... in places where humidity is extremely low.
(below 35%) or extremely high (above 80%).
.... in direct sunlight.
.... in a closed car in summer.
.... near a heater.
4. To protect the unit, DO NOT . . .
.... allow it to become wet.
.... drop the unit or strike it against hard objects.
.... subject it to shock or excessive vibration
during transportation.
.... keep the lens directed at extremely bright
objects for long periods.
.... carry it by holding the lens. Be sure to hold
the main unit with both hands.
.... swing it excessively when using the hand
strap.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
65
LCD Monitor
About moisture condensation . . .
● You may have observed that pouring a cold
liquid into a glass will cause drops of water to
form on the glass’ outer surface. This same
phenomenon occurs on the lens of the
camera when it is moved from a cool place to
a warm place, after heating a cold room,
under extremely humid conditions or in a
place directly subjected to the cool air from
an air conditioner.
1. To prevent damage to the LCD monitor,
DO NOT . . .
.... push it strongly or apply any shocks.
.... place the camcorder with the LCD monitor
on the bottom.
2. To prolong service life . . .
.... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for
LCD monitor use. These are not malfunc-
tions . . .
•While using the camera, the surface around the
LCD monitor and/or the back of the LCD monitor
may heat up.
•If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
How To Handle A CD-ROM
•Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or
back surface. If the CD-ROM gets dirty, gently
wipe it with a soft cloth outward from the centre
hole using a circular motion.
•Do not use conventional disc cleaners or cleaning
spray.
•Do not bend the CD-ROM or touch its mirror
surface.
•Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAJOR SPECIFICATIONS
: 129 (W) x 74 (H) x 39 (D) mm
66
EN
Dimensions
Power consumption
Weight
: 4.2 W
: Approx. 260 g
: DC 6 V
Power
Flash
: Built-in,
Effective shooting distance: 0.5 to 2 m
(with zoom set all the way to “W”)
LCD monitor
: 1.8”
Tripod mounting socket
Storage media
: Provided on the bottom panel
: Built-in flash memory (storage capacity: approx. 3 MB),
Compact Flash card (commercially available)
Compression system
CCD
: JPEG (compatible)
: 1/4”, 350,000 pixel, progressive scan, complementary colour
CCD
Focal distance
: 4.5 to 45 mm
(equivalent to 43 mm to 430 mm on a 35 mm camera)
Zoom
Filter diameter
: 10X optical zoom
: 27 mm
Aperture (F-number)
Minimum subject distance
: F1.6
: Approx. 7 cm (with the zoom set all the way to “W”)
Approx. 1 m (with the zoom set all the way to “T”)
Photometry method
Shutter system
: TTL CCD photometry
: Electronic shutter
Shutter speeds
: Auto/Manual (1/7 to 1/1000 sec.)
: Auto/Manual (Fine/Cloudy/Halogen/M.W.B.)
White balance
Focusing
: Auto/Manual (7 cm to
: 3 modes (Fine/Standard/Economy)
: Fine : approx. 30
)
Picture quality
Number of storable images
Standard : approx. 50
Economy : approx. 100
PC jack
: 2.5 mm dia., 3-pole plug
: 3.5 mm dia., 2-pole plug (PAL)
: 6 V
Video output jack
DC input jack
Infrared transmitter/receiver
: IrDA Ver. 1.0 (IrTran-P compatible)
E. & O. E. Design and specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
EN
67
M
AC outlet.................................. pg. 9
AC power adapter .................... pg. 9
Auto playback.......................... pg. 31
Manual focusing ...................... pg. 26
Manual white balance
(M.W.B.) ................................ pg. 22, 23
Multi-image screen .................. pg. 42, 43
B
N
Battery power remaining .......... pg. 8, 57, 59
Normal playback ..................... pg. 31
Black-and-white effect ............. pg. 38
P
C
Picture Quality mode ............... pg. 15
Playback mode ........................ pg. 31
Power Save mode .................... pg. 28
Power supply ........................... pg. 8, 9
Protecting images..................... pg. 34, 35
Camera setup check................. pg. 17
Compact Flash card ................. pg. 44
Copy ........................................ pg. 47 – 49
D
Date/time ................................. pg. 10
Deleting images ....................... pg. 36, 37
Digital Printer........................... pg. 52
S
Self-Timer................................. pg. 19
Sepia effect .............................. pg. 38
Shooting modes ....................... pg. 14
Shutter speeds .......................... pg. 24, 25
E
Effects ...................................... pg. 38, 39
Exposure compensation ........... pg. 21
T
F
TV monitor............................... pg. 30
Flash ........................................ pg. 20, 29
Frames ..................................... pg. 40, 41
Focusing .................................. pg. 26
Formatting................................ pg. 45
Full Auto shooting.................... pg. 16
V
View modes ............................. pg. 27
W
White balance.......................... pg. 22, 23
I
Z
Index playback......................... pg. 33
INDEX screen........................... pg. 32
Zoom-in effect ......................... pg. 18, 39
Infrared image
communication...................... pg. 50, 51
16-split screen.......................... pg. 42, 43
4-split screen............................ pg. 42, 43
Infrared transmitter/receiver ..... pg. 51
IrDA transfer ............................ pg. 50
IrTran-P .................................... pg. 50
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
VICTOR COMPANY OF JAPAN, LIMITED
0P3ri9n8teMdNinV*JaUpNan*VP
EG/EK
Download from Www.Somanuals.com. All Manuals Search And Download.
COPYRIGHT© 1998 VICTOR COMPANY OF JAPAN, LTD.
|