ENGLISH
AUTOMATIC
DEMONSTRATION
9
DIGITAL VIDEO CAMERA
GETTING STARTED
10
17
23
31
GR-DV4000
Please visit our Homepage on the World Wide
Web for Digital Video Camera:
VIDEO RECORDING &
PLAYBACK
For Accessories:
DIGITAL STILL CAMERA
(D.S.C.) RECORDING &
PLAYBACK
ADVANCED FEATURES
REFERENCES
TERMS
67
86
INSTRUCTIONS
EN
LYT1129-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
3
CAUTIONS:
● This camcorder is designed to be used with PAL-type colour television signals. It cannot be used for
playback with a television of a different standard. However, live recording and LCD monitor/viewfinder
playback are possible anywhere.
● Use the JVC BN-V408U/V416U/V428U battery packs and, to recharge them or supply power to the
camcorder from an AC outlet, use the provided multi-voltage AC Power Adapter/Charger. (An appropriate
conversion adapter may be necessary to accommodate different designs of AC outlets in different
countries.)
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides
to allow for ventilation (10 cm or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
SOME DO’S AND DON’TS ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards but, like any
electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and in accordance with the manufacturer’s
instructions. Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way — switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed
for unattended operation or has a standby mode. Switch off using the switch on the equipment and
make sure that your family knows how to do this. Special arrangements may need to be made for
infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of
road safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating
will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit
the manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
—
—
NEVER let anyone especially children push anything into holes, slots or any other opening in the case —
this could result in a fatal electrical shock;
NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!
Download from Www.Somanuals.com. All Manuals Search And Download.
4
EN
SAFETY PRECAUTIONS
Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to the camcorder and to the user.
When carrying, be sure to always securely attach and use the provided strap. Carrying or holding the
camcorder by the viewfinder and/or the LCD monitor can result in dropping the unit, or in a malfunction.
Take care not to get your finger caught in the cassette holder cover. Do not let children operate the
camcorder, as they are particularly susceptible to this type of injury.
Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the
camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving it on top of the TV is not
recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.
Attach only the optional JVC VL-V3U Video Light, VL-F3U Flash, MZ-V3U Stereo Zoom Microphone or
MZ-V5U Stereo Microphone to the camcorder’s Info-Shoe.
Ⅲ This camcorder is designed exclusively for the digital video cassette, SD Memory Card and
MultiMediaCard. Only cassettes marked “
” can be used with this unit.
” and memory cards marked “
” or
“
Before recording an important scene…
… make sure you only use cassettes with the Mini DV mark
… make sure you only use memory cards with the mark
.
or
.
… remember that this camcorder is not compatible with other digital video formats.
… remember that this camcorder is intended for private consumer use only. Any commercial use without
proper permission is prohibited. (Even if you record an event such as a show, performance or exhibition for
personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5
Provided Accessories
●
AC Power Adapter/
Charger AA-V40EG or
AA-V40EK
●
Battery Pack
BN-V408U-B
●
Remote Control Unit
RM-V717U
●
Audio/Video Cable
(ø3.5 mini-plug to RCA
plug)
●
●
USB Cable
● DC Cord
● Editing Cable
●
●
CD-ROM
Lens Hood
●
Lens Cap
(੬ pg. 7 for attachment)
●
AAA (R03) Battery x 2
(for remote control unit)
Memory Card 8 MB
(Already inserted in the
camcorder)
(Already attached to the
camcorder
੬
pg. 6)
● Shoulder Strap
(੬ pg. 7 for
attachment)
● Audio Cable x 2
(for connection of
optional headphones
and external
● Core Filter (for optional ● Cable Adapter
S-Video cable ੬ pg. 6
for attachment)
microphone ੬ pg. 6)
NOTES:
● In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or
more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to
the camcorder.
● Make sure to use the provided cables for connections. Do not use any other cables.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EN
3 Close the core filter until it clicks shut.
How To Attach/Detach The Lens
Hood
The provided lens hood helps block out glare when
shooting under bright sunlight, the same way
professional photographers do.
To attach:
Align the lens hood with the camcorder’s lens while
the index on the lens hood is facing upward, and
then screw the ring clockwise a.
NOTES:
● If the core filter cannot be attached to the S-Video
cable you have, use the optional YTU94146B
S-Video cable. Consult your nearest JVC dealer for
details on its availability.
To detach:
Turn the ring counterclockwise b.
● Take care not to damage the cable.
● When connecting a cable, attach the end with the
core filter to the camcorder.
Index
How To Use The Audio Cable
When using optional headphones or external
microphone, connect to the provided Audio cable
(with a core filter attached), then connect the Audio
cable to the camcorder. The core filter reduces
interference.
Threading
Ring
Stereo microphone
How To Attach The Core Filter (for
Stereo headphones
optional S-Video cable)
Attach the core filter to an optional S-Video cable.
The core filter reduces interference.
1 Release the stoppers on both ends of the core
filter.
Audio cable
(provided)
Stopper
2 Run the cable through the core filter, leaving
approx. 3 cm of cable between the cable plug
and the core filter. Wind the cable twice around
the outside of the core filter as shown in the
illustration.
Open the
connector cover.
● Wind the cable so that it is not slack.
3 cm
To MIC
Core filter
To
(headphones)
Wind twice.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
7
How To Attach The Lens Cap
To protect the lens, attach the provided lens cap to
the camcorder as shown in the illustration. You can
also attach the lens cap to the lens hood.
How To Attach The Strap
1 Following the illustration, thread the strap
through the eyelet a.
2 Fold it back and thread it through the buckle b.
NOTE:
3 Repeat the procedure to attach the other end of
the strap to the other eyelet c located under the
Grip Strap.
To confirm the lens cap is on correctly make sure the
cap is flush to the camcorder.
4 Confirm the strap is not twisted.
During shooting
Download from Www.Somanuals.com. All Manuals Search And Download.
8
EN
GETTING STARTED
Program AE With Special Effects ............................... 33
Power .......................................................................10
Viewfinder Adjustment .............................................12
LCD Monitor And Viewfinder ...................................12
Brightness Adjustment Of The Display ......................13
Date/Time Settings ....................................................14
Loading A Cassette
Manual Focus ........................................................... 45
Iris Lock ................................................................... 46
Backlight Compensation ........................................... 47
Loading A Memory Card
VIDEO RECORDING & PLAYBACK
VIDEO RECORDING ....................................................17
Basic Recording ........................................................17
Tape Remaining Time ...............................................18
Zooming ...................................................................18
Journalistic Shooting .................................................18
Interface Shooting .....................................................18
Time Code ................................................................19
Still Playback ............................................................20
Shuttle Search ...........................................................21
Dubbing To A Video Unit Equipped With
A DV OUT Connector (Digital Dubbing) .............. 54
SYSTEM CONNECTIONS .............................................. 65
Connection To A Personal Computer .......................65
Using The Camcorder As A WebCam .......................66
DIGITAL STILL CAMERA (D.S.C.) RECORDING &
PLAYBACK
23
D.S.C. RECORDING .....................................................23
Basic Shooting (D.S.C. Snapshot) ..............................23
D.S.C. PLAYBACK .......................................................24
Normal Playback Of Images .....................................24
Auto Playback Of Images .........................................24
Playback Of Video Clips ...........................................25
Playback Of Title Images ..........................................25
Index Playback Of Files ............................................26
Viewing File Information ..........................................26
Removing On-Screen Display ...................................26
Protecting Files .........................................................27
Deleting Files ...........................................................28
Resetting The File Name ...........................................29
Setting Print Information (DPOF Setting) ...................29
Initialising A Memory Card .......................................30
REFERENCES
67
DETAILS .................................................................... 67
TROUBLESHOOTING ................................................... 68
CAUTIONS ................................................................. 74
USER MAINTENANCE .................................................. 77
SPECIFICATIONS ........................................................ 78
INDEX ....................................................................... 80
TERMS
86
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
9
Ⅲ Automatic Demonstration starts when there is no
operation for about 3 minutes after the Power
Switch is set to “A” or “M” and no cassette is in
the camcorder.
Automatic Demonstration
Automatic Demonstration takes place when “DEMO
MODE” is set to “ON” (factory-preset).
Ⅲ Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for more
than 3 minute after that, the demonstration will
resume.
MENU Wheel
Ⅲ “DEMO MODE” remains “ON” even if the
camcorder power is turned off.
To cancel Automatic Demonstration
1 Set the Power Switch to “M” while pressing down
the Lock Button located on the switch.
2 Open the LCD monitor fully, or pull out the
Lock Button
viewfinder fully.
Power Switch
3 Press the MENU Wheel in. The Menu Screen
appears.
Sub Menu
4 Rotate the MENU Wheel to select “s”, and
press it. The SYSTEM Menu appears.
SYSTEM
5 Rotate the MENU Wheel to select “DEMO
MODE”, and press it. The Sub Menu appears.
DEMO MODE
–
OFF
ON
6 Rotate the MENU Wheel to select “OFF”, and
press it.
7 Rotate the MENU Wheel to select “BRETURN”,
and press it twice. The normal screen appears.
NOTE:
Detach the lens cap to see the actual changes of the
Automatic Demonstration activated on the LCD
monitor or viewfinder.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
EN
● When charging the battery pack for the first time
or after a long storage period, the CHARGE
indicator may not light. In this case, remove the
battery pack from the AC Power Adapter/Charger,
then try charging again.
Power
This camcorder’s 2-way power supply system lets
you choose the most appropriate source of power.
Do not use provided power supply units with other
equipment.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
Charging The Battery Pack
● For other notes, ੬ pg. 67.
Battery pack
BN-V408U, BN-V416U
or BN-V428U
Using The Battery Pack
To AC outlet
Power Switch
AC Power
Adapter/
Charger
Lock Button
POWER indicator
CHARGE indicator
BATT.RELEASE Switch
DC OUT connector
Arrow
1 With the arrow on the battery pack pointing
upward, push the battery pack slightly against the
battery pack mount a.
1 Make sure you unplug the camcorder’s DC cord
from the AC Power Adapter/Charger.
2 Slide up the battery pack until it locks in place b.
To detach the battery pack...
2 Plug the AC Power Adapter/Charger’s power cord
into an AC outlet. The POWER indicator lights.
Slide the battery pack down slightly while sliding
BATT. RELEASE to detach it.
3 Attach the battery pack with the YZ mark
aligned with the corresponding marks on the AC
Power Adapter/Charger. The CHARGE indicator
begins blinking to indicate charging has started.
Maximum continuous recording time
Battery pack LCD monitor on Viewfinder on
4 When the CHARGE indicator stops blinking but
stays lit, charging is finished. Remove the battery
pack.
BN-V408U* 1 hr. 5 min.
1 hr. 20 min.
2 hr. 50 min.
5 hr.
BN-V416U
BN-V428U
BN-V840U
BN-V856U
Provided
2 hr. 15 min.
3 hr. 45 min.
5 hr. 20 min.
7 hr. 30 min.
5 Unplug the AC Power Adapter/Charger’s power
cord from the AC outlet.
7 hr.
Battery pack
BN-V408U*
BN-V416U
Charging time
10 hr.
Approx. 1 hr. 30 min.
Approx. 2 hr.
*
NOTES:
BN-V428U
Provided
Approx. 3 hr. 20 min.
● Recording time is reduced significantly under the
following conditions:
*
• Zoom or Record-Standby mode is engaged
repeatedly.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
NOTES:
● If the protective cap is attached to the battery
pack, remove it first.
● If you connect the camcorder’s DC cord to the AC
Power Adapter/Charger during battery charging,
power is supplied to the camcorder and charging
stops.
● Charging is not possible if the wrong type of
battery is used.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
11
About Batteries
ATTENTION:
Before detaching the power source, make sure
that the camcorder’s power is turned off. Failure to
do so can result in a camcorder malfunction.
INFORMATION:
The optional extended-use battery pack kit is a set
composed of a battery pack and AC Power Adapter/
Charger:
Lithium-ion is vulnerable in colder temperatures.
VU-V840 KIT: BN-V840U battery pack & AA-
V15EG or AA-V15EK AC Power Adapter/Charger
VU-V856 KIT: BN-V856U battery pack & AA-
V80EG or AA-V80EK AC Power Adapter/Charger
Read the kit’s instruction manual before using.
Also, by using the optional JVC VC-VBN856U DC
Cord, it will be possible to connect BN-V840U or
BN-V856U battery packs to the camcorder and
supply power directly to the camcorder.
DANGER! Do not attempt to take the batteries apart,
or expose them to flame or excessive heat, as it may
cause a fire or explosion.
WARNING! Do not allow the battery or its terminals
to come in contact with metals, as this can result in
a short circuit and possibly start a fire.
Using AC Power
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have a large
power capacity. However, when one is exposed to
cold temperatures (below 10°C), its usage time
becomes shorter and it may cease to function. If this
happens, place the battery pack in your pocket or
other warm, protected place for a short time, then
re-attach it to the camcorder. As long as the battery
pack itself is not cold, it should not affect
performance.
To DC connector
Open the cover.
To AC outlet
Power cord
(If you’re using a heating pad, make sure the battery
pack does not come in direct contact with it.)
AC Power
Adapter/Charger
For other notes, ੬ pg. 67.
DC cord
To DC OUT
connector
1 Make sure you unplug the camcorder’s DC cord
from the AC Power Adapter/Charger.
2 Plug the AC Power Adapter/Charger’s power cord
into an AC outlet. The POWER indicator lights.
3 Plug the DC cord jack with smaller diameter to
the camcorder’s DC connector.
4 Plug the DC cord jack with larger diameter to the
DC OUT connector on the AC Power Adapter/
Charger.
NOTES:
● The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
● For other notes, ੬ pg. 67.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
EN
● Some tripods are not equipped with studs.
Grip Adjustment
1 Adjust the velcro strip.
2 Pass your right hand through the loop and grasp
the grip.
3 Adjust your thumb and fingers through the grip to
easily operate the Recording Start/Stop Button,
Power Switch and Power Zoom Lever. Be sure to
fasten the velcro strip to your preference.
CAUTION:
When attaching the camcorder to a tripod, extend
its legs to stabilise the camcorder. It is not advised
to use small sized tripods. This may cause damage
to the unit by falling over.
LCD Monitor And Viewfinder
While using the LCD monitor:
Viewfinder Adjustment
1 Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
Make sure the viewfinder is pushed back in. Press
PUSH OPEN and open the LCD monitor fully. It can
rotate 270º (90º downward, 180º upward).
While using the viewfinder:
Make sure the LCD monitor is closed and locked.
Pull out the viewfinder fully.
● Be sure to pull out the viewfinder until you hear a
click, otherwise it may be pushed back in during
use.
2 Make sure the LCD monitor is closed and locked.
Pull out the viewfinder fully and adjust it
manually for best viewability.
3 Turn the Dioptre Adjustment Control until the
indications in the viewfinder are clearly focused.
180˚
PUSH OPEN Button
PAUSE
NOTES:
● The image will not appear simultaneously on the
LCD monitor and the viewfinder except during
Interface Shooting.(੬ pg. 18) When the
viewfinder is pulled out while the LCD monitor is
opened, you can select which one to use. Set
“PRIORITY” to the desired mode in SYSTEM
Menu. (੬ pg. 31, 38)
● Coloured bright spots may appear all over the LCD
monitor or the viewfinder. However, this is not a
malfunction. (੬ pg. 72)
Dioptre Adjustment Control
CAUTION:
When retracting the viewfinder, take care not to
pinch your fingers.
Tripod Mounting
To attach the camcorder to a tripod, align the
direction stud and screw to the mounting socket and
stud hole on the camcorder. Then tighten the screw
clockwise.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
13
Power Switch Position
A (Full Auto Recording):
Brightness Adjustment Of The
Display
Allows you to record using NO special effects or
manual adjustments. Suitable for standard
recording.
1 Set the Power Switch to “M” or “PLAY” while
pressing down the Lock Button located on the
The “A” indicator appears on the display.
2 sOwpietcnht.he LCD monitor fully, or pull out the
M (Manual Recording):
Allows you to set various recording functions
using the Menus. (੬ pg. 31)
If you want more creative capabilities than Full
Auto Recording, try this mode.
There is no indication on the display.
3 vPireewssfitnhdeeMr fEuNllyU. Wheel in. The Menu Screen
appears.
4 Rotate the MENU Wheel to select “n”, and
press it. The CAMERA DISPLAY Menu appears.
5 Rotate the MENU Wheel to select “BRIGHT”,
and press it. The Menu Screen closes and the
brightness control indicator appears.
6 Rotate the MENU Wheel until the appropriate
brightness is reached.
OFF:
Allows you to switch off the camcorder.
PLAY:
● Allows you to play back a video clip on the
memory card.
7 Press the MENU Wheel in.
● It is also possible to adjust the brightness of the
viewfinder.
● Allows you to display a still image stored in the
memory card or to transfer a still image stored in
the memory card to a PC.
● Allows you to set various playback functions
using the Menus. (੬ pg. 31)
VIDEO/MEMORY Switch Position
BR I GHT
VIDEO:
Allows you to record on a tape or play back a
tape. If “REC SELECT” is set to “
/
”
(੬ pg. 39), still images are recorded both on the
tape and the memory card.
MENU Wheel
MEMORY:
● Allows you to record in a memory card or
access data stored in a memory card.
● When the Power Switch is set to “A” or “M”, the
currently selected image size appears.
Operation Mode
To turn on the camcorder, set the Power Switch to
any operation mode except “OFF” while pressing
down the Lock Button located on the switch.
Power-Linked Operation
Power Switch
Lock Button
When the Power Switch is set to “A” or “M”, you
can also turn on/off the camcorder by opening/
closing the LCD monitor or pulling out/pushing in
the viewfinder.
Power Lamp
VIDEO/MEMORY Switch
Choose the appropriate operation mode according
to your preference using the Power Switch and
VIDEO/MEMORY Switch.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
EN
Built-in Clock’s Rechargeable Lithium Battery
Date/Time Settings
The date/time is recorded onto the tape at all times,
but its display can be turned on or off during
playback. (੬ pg. 31, 41)
To store the date/time in memory, the clock’s
rechargeable lithium battery is integrated in the
camcorder. While the camcorder is connected to an
AC outlet using the AC Power Adapter/Charger, or
while the battery pack attached to the camcorder
continues to supply power, the clock’s rechargeable
lithium battery is always charged. However, if the
camcorder is not used for approx. 3 months, the
clock’s lithium battery will become discharged and
the date/time stored in memory will be lost. When
this occurs, first connect the camcorder to an AC
outlet using the AC Power Adapter/Charger for over
24 hours to charge the clock’s rechargeable lithium
battery. Then perform the date/time setting before
using the camcorder.
MENU Wheel
Power Lamp
Lock Button
Power Switch
Note that the camcorder can be used without setting
the date/time.
1 Set the Power Switch to “M” while pressing down
the Lock Button located on the switch.
NOTE:
Even if you select “CLOCK ADJ.”, if the parameter is
not highlighted, the camcorder’s internal clock
continues to operate. Once you move the highlight
bar to the first date/time parameter (day), the clock
stops. When you finish setting the minute and press
the MENU Wheel in, the date and time begin
operation from the date and time you have just set.
2 Open the LCD monitor fully, or pull out the
viewfinder fully.
WI PE / FADER
3 Press the MENU Wheel in.
FADER–WH I TE
FADER–BLACK
FADER–B .W
WI PE–CORNER
WI PE–WI NDOW
WI PE–SL I DE
WI PE–DOOR
The Menu Screen appears.
WI PE–SCROLL
WI PE–SHUTTER
CAMERA DISPLAY
4 Rotate the MENU Wheel
BR I GHT
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
to select “n”, and press
it. The CAMERA DISPLAY
Menu appears.
OFF
2 0 . 12 . 03
17 : 3 0
ADJ .
5 Rotate the MENU Wheel
to select “CLOCK ADJ.”,
and press it. The
RETURN
parameter for “Day” is highlighted.
CAMERA DISPLAY
6 Rotate the MENU Wheel
to input the day, and press
it. Repeat to input the
month, year, hour and
minute.
CLOCK
ADJ .
2 0 . 12 . 03
17 : 3 0
7 Rotate the MENU Wheel
to select “BRETURN”, and
press it twice. The Menu Screen closes.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
15
Approximate recording time
Recording mode
Loading A Cassette
/Unloading A Cassette
The camcorder needs to be powered up to load or
eject a cassette.
Tape
SP
30 min.
LP
30 min.
45 min.
60 min.
80 min.
60 min.
80 min.
90 min.
1 Slide and hold OPEN/EJECT in the direction of
the arrow, then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically.
120 min.
To switch the recording mode, refer to pages 31 and
34.
● Do not touch internal components.
NOTES:
2 Insert or remove a tape and press “PUSH HERE”
● It takes a few seconds for the cassette holder to
open. Do not apply force.
to close the cassette holder.
● Be sure to press only the section labelled
“PUSH HERE” to close the cassette holder;
touching other parts may cause your finger to
get caught in the cassette holder, resulting in
injury or product damage.
● If you wait a few seconds and the cassette holder
does not open, close the cassette holder cover and
try again. If the cassette holder still does not open,
turn the camcorder off then on again.
● If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
● When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
camcorder.
● Even when the camcorder is switched off, a
cassette can be loaded or unloaded. After the
cassette holder is closed with the camcorder
switched off, however, it may not recede. It is
recommended to turn the power on before
loading or unloading.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
● When the battery pack’s charge is low, you
may not be able to close the cassette holder
cover. Do not apply force. Replace the battery
pack with a fully charged one or use AC power
before continuing.
3 Close the cassette holder cover firmly until it
locks into place.
Erase protection tab
Make sure the
window side is
● When resuming recording, once you open the
cassette holder cover a blank portion will be
recorded on the tape or a previously recorded
scene will be erased (recorded over) regardless of
whether the cassette holder came out or not. See
“Recording From The Middle Of A Tape”
(੬ pg. 19).
facing out.
PUSH HERE
Cassette holder
Cassette
holder cover
OPEN/EJECT Switch
To protect valuable recordings…
Slide the erase protection tab on the back of the tape
in the direction of “SAVE”. This prevents the tape
from being recorded over. To record on this tape,
slide the tab back to “REC” before loading it.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
EN
To protect valuable files (available only for SD
Memory Card)…
Loading A Memory Card
/Unloading A Memory Card
Write/erase protection tab
The provided memory card is already inserted in the
camcorder at the time of purchase.
Slide the write/erase protection tab on the side of the
memory card in the direction of “LOCK”. This
prevents the memory card from being recorded over.
To record on this memory card, slide the tab back to
the position opposite to “LOCK” before loading it.
Card Cover (MEMORY CARD)
Memory card
NOTES:
● Be sure to use only SD Memory Cards marked
“
“
” or MultiMediaCards marked
”.
Label
● Some brands of memory cards are not compatible
with this camcorder. Before purchasing a memory
card, consult its manufacturer or dealer.
Clipped edge
● Before using a new memory card, it is necessary to
FORMAT the card. (੬ pg. 30)
1 Make sure the camcorder’s power is off.
2 Open the card cover (MEMORY CARD).
ATTENTION:
3 To load a memory card, firmly insert it with its
Do not insert or remove the memory card while the
camcorder is turned on, as this may cause the
memory card to be corrupted or cause the
camcorder to become unable to recognise whether
or not the card is installed.
clipped edge first.
To unload a memory card, push it once. After the
memory card comes out of the camcorder, pull it
out.
● Do not touch the terminal on the reverse side
of the label.
4 Close the card cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
17
VIDEO RECORDING
4 Set the Power Switch to “A” or “M” while
Basic Recording
NOTE:
Before continuing, perform the procedures listed
below:
pressing down the Lock Button located on the
switch.
● The power lamp lights and the camcorder
enters the Record-Standby mode. “PAUSE” is
displayed.
● Power (੬ pg. 10)
● Loading A Cassette (੬ pg. 15)
5 To start recording, press the Recording Start/Stop
Button. The tally lamp lights and “T REC”
appears on the display while recording is in
progress.
Power Lamp
Power Zoom Lever
6 To stop recording, press the Recording Start/Stop
Button again. The camcorder re-enters the
Record-Standby mode.
NOTES:
● The image will not appear simultaneously on the
LCD monitor and the viewfinder.
5 minutes, the camcorder’s power shuts off
push back and pull out the viewfinder again or
close and re-open the LCD monitor.
● LCD monitor/viewfinder indications:
• When power is supplied from a battery: the
Power Switch
Lock Button
Recording Start/Stop Button
“
” battery indicator is displayed. (੬ pg. 84)
• When power is supplied from an AC outlet: the
” battery indicator does not appear.
VIDEO/MEMORY Switch
“
● When a blank portion is left between recorded
scenes on the tape, the time code is interrupted
and errors may occur when editing the tape. To
avoid this, refer to “Recording From The Middle
Of A Tape” (੬ pg. 19).
● To turn the tally lamp or beep sounds off,
੬ pg. 31, 37.
● To record in LP (Long Play) mode, ੬ pg. 31, 34.
● For other notes, ੬ pg. 67.
Tally Lamp
(Lights while recording is in
progress.)
INFO LCD
PUSH OPEN Button
INFO LCD Indications
1
2
3
a Tape indicator
(Appears when a cassette is loaded and blinks
when no cassette is loaded.)
b Recording time
c Battery indicator
● To turn off the indications, ੬ pg. 31, 38.
1 Remove the lens cap.
2 Press PUSH OPEN and open the LCD monitor
fully, or pull out the viewfinder fully.
3 Set the VIDEO/MEMORY Switch to “VIDEO”.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
EN
● Zoom magnification of over 10X is done through
Digital image processing, and is therefore called
Digital Zoom.
● During Digital zoom, the quality of image may
suffer.
Tape Remaining Time
Approximate tape remaining time appears on the
display. “– h – – m” means the camcorder is
calculating the remaining time. When the remaining
time reaches 2 minutes, the indication starts
blinking.
● Digital zoom cannot be used when the VIDEO/
MEMORY Switch is set to “MEMORY”.
● Macro shooting (as close as approx. 5 cm to the
subject) is possible when the Power Zoom Lever is
set all the way to “W”. Also see “TELE MACRO” in
MANUAL Menu on page 36.
0
h
25
m
● For other notes, ੬ pg. 67.
–h––m
(Now calculating)
1h 0m
0h59m
0h 1m
0h 3m
0h 2m
Journalistic Shooting
0h 0m
In some situations, different
shooting angles may provide
more dramatic results. Hold
the camcorder in the desired
position and tilt the LCD
monitor in the most
convenient direction. It can
rotate 270º (90º downward,
180º upward).
(Blinking)
(Blinking) (Blinking)
Zooming
Produces the zoom in/out effect, or an instantaneous
change in image magnification.
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
Interface Shooting
Slide the Power Zoom Lever towards “W”.
● The further you slide the Power Zoom Lever, the
quicker the zoom action.
The person you shoot can view himself/herself in the
LCD monitor, and you can even shoot yourself while
viewing your own image in the LCD monitor.
Zoom in (T: Telephoto)
1
x
W
T
10
x
W
T
Self Recording
20
xW
T
40
xW
T
1) Open the LCD monitor and tilt it upward to 180º
so that it faces forward.
● When the LCD monitor is tilted upward to an
angle of over approx. 105º, the monitor image
is inverted vertically. If the viewfinder is pulled
out at that time, it also switches on.
Digital zoom zone
10
x
W
T
2) Point the lens toward the subject (yourself when
self-recording) and start recording.
10X (optical) zoom zone
Approximate zoom ratio
● During Interface Shooting, the monitor image
and indications do not appear inverted as they
would when viewing a mirror.
NOTES:
● Focusing may become unstable during Zooming.
In this case, set the zoom while in Record-
Standby, lock the focus by using the manual focus
(੬ pg. 45), then zoom in or out in Record mode.
● Zooming is possible to a maximum of 300X, or it
can be switched to 10X magnification using the
optical zoom. (੬ pg. 34)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
Time Code
Recording From The Middle Of A Tape
During recording, a time code is recorded on the
tape. This code is to confirm the location of the
If recording starts from a blank portion, the time
code begins counting from “00:00:00”
1) Play back a tape or use Blank Search (੬ pg. 21)
to find the spot at which you want to start
recording, then engage the Still Playback mode.
(੬ pg. 20)
2) Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch, then start recording.
(minute:second:frame). If recording starts from the
end of a previously recorded scene, the time code
continues from the last time code number.
To perform Random Assemble Editing (੬ pg. 60 –
64), time code is necessary. If during recording a
blank portion is left partway through the tape, the
time code is interrupted. When recording is
resumed, the time code starts counting up again
from “00:00:00”. This means the camcorder may
record the same time codes as those existing in a
previously recorded scene. To prevent this, perform
“Recording From The Middle Of A Tape” (੬ pg. 19)
in the following cases;
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time
code indication does not move smoothly.
● The time code is displayed only when “TIME
CODE” is set to “ON”. (੬ pg. 38)
When a blank portion is recorded on a tape
Time code
00:00:00
Time code Time code
05:43:21 00:00:00
● When shooting again after playing back a
recorded tape.
● When power shuts off during shooting.
● When a tape is removed and re-inserted during
shooting.
Already
recorded scene
Newlyrecorded
scene
Blank
Tape
● When shooting using a partially recorded tape.
● When shooting on a blank portion located
partway through the tape.
Shooting start Shooting stop Shooting start
point
point point
● When shooting again after shooting a scene then
opening/closing the cassette holder cover.
Proper recording
Display
Frames are not displayed
during recording.
Time code
00:00:00
Time code Time code
05:43:21 05:44:00
Minutes
Seconds
Already
recorded scene
New
scene
Tape
Latest scene
Frames
(25 frames = 1 second)
12 : 34 : 24
Shooting start Shooting start Shooting start
point point point
Download from Www.Somanuals.com. All Manuals Search And Download.
20
EN
VIDEO PLAYBACK
NOTES:
Normal Playback
MENU Wheel (VOLUME)
● Clean the video heads using an optional dry
cleaning cassette when:
• No picture during playback.
• Blocks of noise appear during playback.
For details, ੬ pg. 76.
● If Stop mode continues for 5 minutes when power
is supplied from a battery, the camcorder shuts off
automatically. To turn on again, set the Power
Switch to “OFF”, then to “PLAY”.
● The playback picture can be viewed in the LCD
monitor, viewfinder or on a connected TV.
(੬ pg. 22)
● You can also view the playback picture on the
LCD monitor with it flipped over and pushed
against the camcorder body.
Power Switch
● LCD monitor/viewfinder indications:
Lock Button
• When power is supplied from a battery: the
“
” battery indicator is displayed. (੬ pg. 84)
VIDEO/MEMORY Switch
• When power is supplied from an AC outlet: the
Stop Button (8)
“
” battery indicator does not appear.
Play/Pause Button (4/9)
● When a cable is connected to the AV connector,
the sound is not heard from the speaker.
To control the speaker volume…
Rotate the MENU Wheel towards “+” to turn up the
volume, or towards “–” to turn down the volume.
Still Playback
Pauses during video playback.
1) Press 4/9 during playback.
Rewind Button (3)
Fast-Forward Button (5)
2) To resume normal playback, press 4/9 again.
● If still playback continues for more than about
3 minutes, the camcorder’s Stop mode is
automatically engaged.
Speaker
● When 4/9 is pressed, the image may not
pause immediately while the camcorder
stabilises the still image.
1 Load a cassette. (੬ pg. 15)
2 Set the VIDEO/MEMORY Switch to “VIDEO”.
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
4 To start playback, press 4/9.
5 To stop playback, press 8.
● During Stop mode, press 3 to rewind, or
5 to fast-forward the tape.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
21
NOTES:
Shuttle Search
● Before starting Blank Search, if the current position
is at a blank portion, the camcorder searches in
the reverse direction. If the current position is at a
recorded portion, the camcorder searches in the
forward direction.
● Blank Search does not work if “HEAD CLEANING
REQUIRED. USE CLEANING CASSETTE” has
appeared with the tape.
● If the beginning or end of the tape is reached
during Blank Search, the camcorder stops
automatically.
● A blank portion which is shorter than 5 seconds of
tape may not be detected.
Allows high-speed search in either direction during
video playback.
1) During playback, press 5 for forward search,
or 3 for reverse search.
2) To resume normal playback, press 4/9.
● During playback, press and hold 5 or 3.
The search continues as long as you hold the
button. Once you release the button, normal
playback resumes.
during Shuttle Search. This is not a
malfunction.
● The detected blank portion may be located
between recorded scenes. Before you start
recording, make sure there is no recorded scene
after the blank portion.
ATTENTION:
During Shuttle Search, parts of
the picture may not be clearly
visible, particularly on the left
side of the screen.
Slow-Motion Playback
Frame-By-Frame Playback
Playback Zoom
Blank Search
Helps you find where you should start recording in
the middle of a tape to avoid time code interruption.
(੬ pg. 19)
Playback Special Effects
Available only with the remote control (provided).
(੬ pg. 57)
1 Load a cassette. (੬ pg. 15)
2 Set the VIDEO/MEMORY Switch to “VIDEO”.
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
4 During Stop mode,
press BLANK
SEARCH.
BLANK SEARCH
● The “BLANK
PUSH "STOP" BUTON
TO CANCEL
SEARCH”
indication appears
and the camcorder
automatically starts
reverse or forward search, then stops at the
spot which is about 3 seconds of tape before
the beginning of the detected blank portion.
● To cancel Blank Search midway, press 8.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
EN
VIDEO PLAYBACK (cont.)
1 Make sure all units are turned off.
Connections To A TV Or VCR
2 Connect the camcorder to a TV or VCR as shown
in the illustration.
If using a VCR, go to step 3.
If not, go to step 4.
3 Connect the VCR output to the TV input,
Connector
Cover****
4 Turn on the camcorder, the VCR and the TV.
5 Set the VCR to its AUX input mode, and set the
To S
Connector
Cover****
To choose whether or not the following displays
appear on the connected TV…
● Date/Time
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
(੬ pg. 31, 41)
To AV
Audio/Video
cable
(provided)
S-Video cable
(optional)
Or, press DISPLAY on the remote control to turn
on/off the date indication.
● Time Code
Set “TIME CODE” to “ON” or “OFF”.
(੬ pg. 31, 41)
1
2
3
4
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.
(੬ pg. 31, 41)
NOTES:
“Y/C”/“CVBS”
Video Out Select
Switch
Cable Adapter*
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 11)
To TV or VCR
● To monitor the picture and sound from the
camcorder without inserting a tape or memory
card, set the camcorder’s Power Switch to “A” or
“M”, then set your TV to the appropriate input
mode.
VCR
TV
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the
TV as interference will occur in the camcorder
playback picture.
● When a cable is connected to the AV or
headphone connector, sound cannot be heard
from the speaker.
A White to AUDIO L IN**
B Red to AUDIO R IN**
C Yellow to VIDEO IN
D To S-VIDEO IN***
*
If your VCR has a SCART connector, use the
provided cable adapter.
** Not required for watching still images only.
*** Connect when your TV/VCR has S-VIDEO IN
and A/V input connectors. In this case, it is not
necessary to connect the yellow video cable.
**** When connecting the cable, open the cover.
NOTE:
Set the video out select switch of the cable adapter
as required:
Y/C: When connecting to a TV or VCR which
accepts Y/C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which does
not accept Y/C signals and uses an audio/video
cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
23
D.S.C. RECORDING
Basic Shooting (D.S.C. Snapshot)
You can use your camcorder as a Digital Still
Camera for taking snapshots. Still images are stored
in the memory card.
A Image Size (੬ pg. 39, 82)
B Focus Icon (੬ pg. 82)
C Shooting Icon (੬ pg. 82)
D Card Icon (੬ pg. 82)
E Picture Quality (੬ pg. 39, 82)
F Remaining Number Of Shots (੬ pg. 82)
NOTE:
Before continuing, perform the procedures listed
below:
● Power (੬ pg. 10)
● Loading A Memory Card (੬ pg. 16)
SNAPSHOT Button
Power Switch
INFO LCD Indications
2
1
3
PUSH OPEN Button
Lock Button
a Memory card indicator
(Appears when a memory card is loaded and
blinks when no memory card is loaded)
b Number of shots
c Battery indicator
● To turn off the indications, ੬ pg. 31, 38.
NOTES:
● Even if “DIS” is set to “ON” (੬ pg. 35), the
Stabiliser will be disabled.
● If Snapshot recording is not possible, “O”
blinks when SNAPSHOT is pressed.
VIDEO/MEMORY Switch
1 Remove the lens cap.
● If Program AE with special effects (੬ pg. 33) is
engaged, certain modes of Program AE with
special effects are disabled during Snapshot
recording. In such a case, the icon blinks.
● If shooting is not performed for approx. 5 minutes
when the Power Switch is set to “A” or “M” and
power is supplied from the battery pack, the
camcorder shuts off automatically to save power.
the viewfinder again or close and re-open the LCD
monitor.
● The Motor Drive mode (੬ pg. 42) is disabled
when the VIDEO/MEMORY Switch is set to
“MEMORY”.
● When a cable is connected to the AV connector,
the shutter sound is not heard from the speaker,
however it is recorded onto the tape.
● Still images taken are compliant to DCF (Design
rule for Camera File system). They do not have any
compatibility with devices which are not
compliant to DCF.
2 Press PUSH OPEN and open the LCD monitor
fully, or pull out the viewfinder fully.
3 Set the VIDEO/MEMORY Switch to “MEMORY”.
4 Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
5 Press SNAPSHOT. The “O” indication
appears while the snapshot is being taken.
recording it in the memory card, press
SNAPSHOT halfway and hold. The “
”
indicator appears and stops blinking when the
captured image is focused. To cancel the
recording, release SNAPSHOT. To record it in
the memory card, press SNAPSHOT fully.
● Still images are recorded in the snapshot mode
with no frame.
● To delete unwanted still images, refer to
“Deleting Files” (੬ pg. 28).
● When you do not want to hear the shutter
sound, set “BEEP” to “OFF”. (੬ pg. 31, 37)
● To change the Image Size and/or Picture
Quality, ੬ pg. 31, 39.
.
Snapshot mode with no frame
There is the sound of a shutter
closing.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
EN
D.S.C. PLAYBACK
● Images shot in a file size other than “640 x 480”,
“1024 x 768”, “1280 x 960” and “1600 x 1200”
with another devices will be displayed thumbnail
images. These thumbnail images cannot be
transferred to a PC.
● Images shot with devices (such as JVC GR-DVX7)
that are not compatible with DCF cannot be
FILE!” will be displayed.
Normal Playback Of Images
Images shot with the camcorder are automatically
numbered, then stored in numerical order in the
memory card. You can view the stored images, one
at a time, much like flipping through a photo album.
Power Switch
Lock Button
MENU Wheel
Rewind Button (3)
Playback Zoom
Available only with the remote control (provided).
(੬ pg. 57)
Stop Button (8)
VIDEO/
MEMORY
Switch
You can run through all the images stored in
memory card automatically.
1 Perform steps 1 – 6 in “Normal Playback Of
Images”.
2 Press 4/9 to start Auto Playback.
● If you press 3 during Auto Playback, files
are displayed in descending order.
INFO Button
SELECT Button
Fast-Forward Button (5)
3 To end Auto Playback, press 8.
1 Load a memory card. (੬ pg. 16)
[For Normal Playback]
[For Auto Playback]
To display the next image
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
Image playback screen (IMAGE)
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
100-0013
4 Open the LCD monitor fully, or pull out the
viewfinder fully.
which has been played back at the last time is
displayed.
100-0014
5 If the video clip playback (E-MAIL CLIP,
੬ pg. 25) screen appears, press SELECT. The
MEMORY SELECT screen appears.
100-0015
6 Rotate the MENU Wheel to select “IMAGE”, and
press it. The image playback screen (IMAGE)
appears.
100-0016
7 Press 3 to display the previous file. Press 5
to display the next file.
● Pressing INFO gives you details on the
displayed file. (੬ pg. 26)
● You can also look for the desired file using
Index Screen. (੬ pg. 26)
To display the previous image
● You can turn off the on-screen playback
display. (੬ pg. 26)
NOTES:
● Even if you shoot a new image after playing back a
low-numbered one, this will not overwrite an
existing image, because new images are
automatically stored after the last-recorded one.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
25
Playback Of Video Clips
Playback Of Title Images
You can view video clips (੬ pg. 50) stored in the
9 title images are pre-stored in the provided memory
card. You can view these files. The title images can
be also superimposed during recording. (੬ pg. 51)
memory card.
1 Load a memory card. (੬ pg. 16)
1 Load the provided memory card. (੬ pg. 16)
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
4 Open the LCD monitor fully, or pull out the
viewfinder fully.
4 Open the LCD monitor fully, or pull out the
● The type of file (IMAGE, E-MAIL CLIP or TITLE)
which has been played back at the last time is
displayed.
viewfinder fully.
● The type of file (IMAGE, E-MAIL CLIP or TITLE)
which has been played back at the last time is
displayed.
5 If the image playback (IMAGE) or the title image
The MEMORY SELECT screen appears.
5 If the image playback (IMAGE) or the video clip
playback (E-MAIL CLIP) screen appears, press
SELECT. The MEMORY SELECT screen appears.
6 Rotate the MENU Wheel
E-MAIL CLIP
to select “E-MAIL CLIP”,
and press it. The video clip
playback screen (E-MAIL
CLIP) appears.
6 Rotate the MENU Wheel
to select “TITLE”, and
press it. The title image
playback screen (TITLE)
appears.
7 Press 3 to select the
previous file. Press 5 to
7 Press 3 to select the
select the next file.
previous file. Press 5 to
● Pressing INFO gives you details on the
displayed file. (੬ pg. 26)
select the next file.
● Pressing INFO gives you details on the
displayed file. (੬ pg. 26)
● You can also look for the desired file using
Index Screen. (੬ pg. 26)
● You can also look for the desired file using
Index Screen. (੬ pg. 26)
8 To start playback, press 4/9.
9 To stop playback, press 8.
NOTE:
If the pre-stored title images in the provided memory
card have been deleted accidentally, you can copy
the image files from the provided CD-ROM. For
details, refer to the provided software’s instruction
manual included in the CD-ROM.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
EN
D.S.C. PLAYBACK (cont.)
Information Screen
Index Playback Of Files
You can view several different files stored in the
memory card at a time. This browsing capability
makes it easy to locate a particular file you want.
FOLDER
F I LE
: 1 0 0 JVCGR
: DVC0 0 0 1 0
2 7 . 1 0 .0 3
DATE
:
S I ZE
QUAL I TY : F I NE
PROTECT : OFF
: 1 0 2 4X7 6 8
1 For Index Playback of image files, perform 1 – 6
in “Normal Playback Of Images” (੬ pg. 24).
● Press the INFO Button again to close the
For Index Playback of video clip files, perform
1 – 6 in “Playback Of Video Clips” (੬ pg. 25).
For Index Playback of title files, perform 1 – 6 in
“Playback Of Title Images” (੬ pg. 25).
Information Screen.
NOTE:
With images shot with other devices or processed on
a PC, “QUALITY: – – –” will be displayed.
2 Press INDEX. The Index Screen of the selected
type of file appears.
Removing On-Screen Display
Selected file
Index number
1 Perform steps 1 – 6 in “Normal Playback Of
Images” (੬ pg. 24) or “Playback Of Title Images”
(੬ pg. 25).
Index Screen
1
4
7
2
5
8
3
6
9
2 Press the MENU Wheel in. The Menu Screen
appears.
3 Rotate the MENU Wheel to select “DISPLAY”,
and press it. The Sub Menu appears.
3 Rotate the MENU Wheel to move the frame to
the desired file.
4 Rotate the MENU Wheel to select “OFF”, and
press it. The operation mode indicator, folder/file
● Press 3 to display the previous page. Press
5 to display the next page.
) disappear.
4 Press the MENU Wheel in. The selected file is
Operation mode indicator
Folder/file number
displayed.
● Pressing INFO gives you details on the
displayed file. (See below.)
100-0013
MENU
Viewing File Information
You can get the relevant file information by pressing
the INFO Button during normal playback or Index
Playback.
D I SPLAY OFF
ON
Battery indicator
FOLDER
FILE
DATE
SIZE
QUALITY
TIME
:
:
:
:
:
:
:
Folder name (੬ pg. 29)
File name (੬ pg. 29)
Date the file was made
Image size
Picture quality (IMAGE only)
Playback time (E-MAIL CLIP only)
When set to “ON”, the file is
protected from accidental erasure.
(੬ pg. 27)
PROTECT
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
27
To protect the currently displayed file
Protecting Files
The Protect mode helps prevent the accidental
erasure of files.
9 Rotate the MENU Wheel
MENU
to select “CURRENT”, and
PROTECT
CURRENT
PROT . ALL
CANC . ALL
press it. The PROTECT
screen appears.
RETURN
MENU Wheel
Power Switch
10 Press 3 or 5 to
select the desired file.
Lock Button
11 Rotate the MENU
PROTECT
Wheel to select
Rewind Button (3)
“EXECUTE”, and press it.
● To cancel protection,
select “RETURN”.
VIDEO/MEMORY Switch
PROTECTED
RETURN
● Repeat steps 10 and 11
for all files you want to
protect.
To protect all files stored in the memory
card
9 Rotate the MENU Wheel to select “PROT.ALL”,
and press it. The PROTECT screen appears.
SELECT Button
Fast-Forward Button (5)
10 Rotate the MENU Wheel to select “EXECUTE”,
and press it.
● To cancel protection, select “RETURN”.
1 Load a memory card. (੬ pg. 16)
NOTES:
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
● If the “
” mark appears, the currently displayed
3 Set the Power Switch to “PLAY” while pressing
file is protected.
down the Lock Button located on the switch.
● When the memory card is initialised or corrupted,
even protected files are deleted. If you do not want
to lose important files, transfer them to a PC and
save them.
4 Open the LCD monitor fully, or pull out the
viewfinder fully.
● The type of file (IMAGE, E-MAIL CLIP or TITLE)
which has been played back at the last time is
displayed.
To Remove Protection
Before doing the following, perform steps 1 – 8 in
“Protecting Files” in the left column.
If you want to select another type of file, go to
step 5.
If not, go to step 7.
To remove protection from the currently
displayed file
5 Press SELECT. The MEMORY SELECT screen
appears.
9 Rotate the MENU Wheel to select “CURRENT”,
6 Rotate the MENU Wheel to select the desired
and press it. The PROTECT screen appears.
type of file, and press it.
10 Press 3 or 5 to select the desired file.
7 Press the MENU Wheel in. The Menu Screen
11 Rotate the MENU Wheel to select “EXECUTE”,
appears.
and press it.
8 Rotate the MENU Wheel
MENU
● To cancel selection, select “RETURN”.
● Repeat steps 10 and 11 for all files you want to
remove protection.
to select “PROTECT”, and
PROTECT
DELETE
press it. The Sub Menu
appears.
DPOF
NO . RESET
FORMAT
D I SPLAY
BR IGHT
END
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
28
EN
D.S.C. PLAYBACK (cont.)
To remove protection from all files stored
in the memory card
To delete the currently displayed file
9 Rotate the MENU Wheel
MENU
to select “CURRENT”, and
9 Rotate the MENU Wheel to select “CANC.ALL”,
DELETE
CURRENT
ALL
press it. The DELETE
screen appears.
and press it. The PROTECT screen appears.
RETURN
10 Rotate the MENU Wheel to select “EXECUTE”,
10 Press 3 or 5 to
and press it.
select the desired file.
● To cancel selection, select “RETURN”.
11 Rotate the MENU
DELETE
Wheel to select
“EXECUTE”, and press it.
● To cancel deletion,
select “RETURN”.
● Repeat steps 10 and 11
for all files you want to
delete.
Deleting Files
Previously stored files can be deleted either one at a
time or all at once.
DELETE?
EXECUTE
RETURN
MENU Wheel
Power Switch
NOTE:
If the “
” mark appears, the selected file is
Lock Button
protected and cannot be deleted.
Rewind Button (3)
card
VIDEO/MEMORY Switch
9 Rotate the MENU Wheel to select “ALL”, and
press it. The DELETE screen appears.
10 Rotate the MENU Wheel to select “EXECUTE”,
and press it.
● To cancel deletion, select “RETURN”.
NOTES:
delete them, remove protection first.
● Once files are deleted, they cannot be restored.
Check files before deleting.
SELECT Button
Fast-Forward Button (5)
1 Load a memory card. (੬ pg. 16)
CAUTION:
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
Do not remove the memory card or perform any
other operation (such as turning off the
camcorder) during deletion. Also, be sure to use
the provided AC Power Adapter/Charger, as the
memory card may be corrupted if the battery
becomes exhausted during deletion. If the
memory card becomes corrupted, initialise it.
(੬ pg. 30)
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
4 Open the LCD monitor fully, or pull out the
viewfinder fully.
● The type of file (IMAGE, E-MAIL CLIP or TITLE)
which has been played back at the last time is
displayed.
If you want to select another type of file, go to
step 5.
If not, go to step 7.
5 Press SELECT. The MEMORY SELECT screen
appears.
6 Rotate the MENU Wheel to select the desired
type of file, and press it.
7 Press the MENU Wheel in. The Menu Screen
appears.
8 Rotate the MENU Wheel to select “DELETE”, and
press it. The Sub Menu appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Resetting The File Name
Setting Print Information (DPOF
Setting)
(Digital Print Order Format) standard in order to
support future systems such as automatic printing.
You can select one of the 2 print information settings
Still Images (One Print For Each)” or “To Print By
Selecting Still Images And Number Of Prints”.
By resetting the file name, a new folder will be
made. The new files you are going to make will be
stored in the new folder. It is convenient to separate
the new files from previously made files. (Available
only for Image and video clip files.)
1 Load a memory card. (੬ pg. 16)
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
NOTES:
4 Open the LCD monitor fully, or pull out the
● If you load a memory card already set as shown
below in a printer compatible with DPOF, it will
make prints of the selected still images
automatically.
viewfinder fully.
● The type of file (IMAGE, E-MAIL CLIP or TITLE)
which has been played back at the last time is
displayed.
● To print images recorded on a tape, first dub them
to a memory card. (੬ pg. 55)
5 If the title image playback (TITLE, ੬ pg. 25)
screen appears, press SELECT. The MEMORY
SELECT screen appears.
6 Rotate the MENU Wheel to select the desired
type of file (IMAGE or E-MAIL CLIP), and press it.
The image or video clip playback screen (IMAGE
or E-MAIL CLIP) appears.
1 Load a memory card. (੬ pg. 16)
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
3 Set the Power Switch to “PLAY” while pressing
7 Press the MENU Wheel in. The Menu Screen
down the Lock Button located on the switch.
appears.
4 Open the LCD monitor fully, or pull out the
8 Rotate the MENU Wheel to select “NO. RESET”,
viewfinder fully.
and press it. The NO. RESET screen appears.
● The type of file (IMAGE, E-MAIL CLIP or TITLE)
which has been played back at the last time is
displayed.
9 Rotate the MENU Wheel to select “EXECUTE”,
and press it. The new folder (such as
“101JVCGR”) will be made and the file made of
the next shot starts from DVC00001.
5 If the video clip playback (E-MAIL CLIP,
੬ pg. 25) or the title image playback (TITLE,
੬ pg. 25) screen appears, press SELECT. The
MEMORY SELECT screen appears.
Folder and File names
Each time shooting takes place, a file name is made
using a number which is larger by one than the
largest number of the file names which are in use.
Even if you delete an image or video clip file with a
number in the middle of range, the number will not
be used for a new shot; a gap will remain in the
numerical sequence. If the file name reaches
DVC09999, a new folder (such as “101JVCGR”) will
be made and the file name will start again from
DVC00001.
6 Rotate the MENU Wheel to select “IMAGE”, and
press it. The image playback screen (IMAGE)
appears.
7 Press the MENU Wheel in. The Menu Screen
appears.
8 Rotate the MENU Wheel
MENU
to select “DPOF”, and
DPOF
CURRENT
ALL
RESET
RETURN
press it. The Sub Menu
appears.
1
9 Rotate the MENU Wheel
to select “ALL 1”, and
press it. The DPOF screen
appears.
10 Rotate the MENU
DPOF
Wheel to select
“EXECUTE”, and press it.
The normal playback
screen appears.
ALL1?
EXECUTE
RETURN
● To cancel selection,
select “RETURN”.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
30
EN
D.S.C. PLAYBACK (cont.)
To Print By Selecting Still Images And Number
Initialising A Memory Card
You can initialise a memory card any time.
After initialising, all files and data stored in the
memory card, including those which have been
protected, are cleared.
Of Prints
1 Perform steps 1 – 8 in “To Print All Still Images
(One Print For Each)” (੬ pg. 29).
2 Rotate the MENU Wheel
DPOF
to select “CURRENT”, and
press it. The DPOF screen
1 Set the VIDEO/MEMORY Switch to “MEMORY”.
2 Set the Power Switch to “PLAY” while pressing
SHEETS
appears.
down the Lock Button located on the switch.
0 0
RETURN
3 Press 3 or 5 to
3 Open the LCD monitor fully, or pull out the
select the desired file.
viewfinder fully.
4 Rotate the MENU Wheel to select the number
4 Press the MENU Wheel in.
indication (00), and press it.
MENU
PROTECT
DELETE
DPOF
The Menu Screen appears.
5 Select the number of prints
DPOF
NO . RESET
FORMAT
D I SPLAY
BR I GHT
END
by rotating the MENU
Wheel towards “+” to
SHEETS
increase number, or
0 5
towards “–” to decrease
the number, and press it.
● Repeat steps 3 through 5
FORMAT
5 Rotate the MENU Wheel
to select “FORMAT”, and
ERASE ALL
EX I ST I NG DATA?
press it. The FORMAT
screen appears.
for the desired number of prints.
● The number of prints can be set up to 15.
● To correct the number of prints, select the
image again and change the number.
EXECUTE
RETURN
6 Rotate the MENU Wheel
to select “EXECUTE”, and
press it. The memory card
● When initialisation is finished, “NO IMAGES
STORED”, “NO E-MAIL CLIP STORED” or
“NO TITLE DATA STORED” appears.
● To cancel initialisation, select “RETURN”.
6 Rotate the MENU Wheel
DPOF
to select “RETURN”, and
press it. The “SAVE?”
SAVE?
appears.
EXECUTE
CANCEL
● If you did not change
any settings in step 3
through 5, the Menu
CAUTION:
Screen reappears.
Do not perform any other operation (such as
turning off the camcorder) during initialisation.
Also, be sure to use the provided AC Power
Adapter/Charger, as the memory card may be
corrupted if the battery becomes exhausted during
initialisation. If the memory card becomes
corrupted initialise it.
7 Rotate the MENU Wheel to select “EXECUTE” to
save the setting you have just made, and press it.
● To cancel selection, select “CANCEL”.
To Reset The Number Of Prints
1 Perform steps 1 – 8 in “To Print All Still Images
(One Print For Each)” (੬ pg. 29).
2 Rotate the MENU Wheel to select “RESET”, and
press it. The DPOF screen appears.
3 Rotate the MENU Wheel to select “EXECUTE”,
and press it. The normal playback screen
appears.
● To cancel selection, select “RETURN”.
● The number of prints is reset to 0 for all still
images.
CAUTION:
While performing the above, never disconnect
power, as this may cause the memory card to be
corrupted.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
31
MENUS FOR DETAILED ADJUSTMENT
Menus without Sub Menus
— v WIPE/FADER, r PROGRAM AE,
u W. BALANCE
Changing The Menu Settings
This camcorder is equipped with an easy-to-use, on-
screen menu system that simplifies many of the
more detailed camcorder settings. (੬ pg. 32 – 41)
1) Rotate the MENU Wheel to select the desired
parameter.
Example: r PROGRAM AE Menu
PROGRAM AE
MENU Wheel
SHUTTER
Selected menu icon blinks.
SHUTTER
SPORTS
SNOW
SPOTLIGHT
TWILIGHT
SEPIA
Power Switch
Lock Button
MONOTONE
Selected parameter
WI PE / FADER
2) Press the MENU Wheel in.
FADER–WH I TE
FADER–BLACK
Selection is complete. The
FADER–B .W
WI PE–CORNER
Menu Screen returns.
WI PE–WI NDOW
WI PE–SL I DE
● Repeat the procedure if
WI PE–DOOR
WI PE–SCROLL
you wish to set other
function menus.
WI PE–SHUTTER
3) Press the MENU Wheel in
Menus with Sub Menus
— m CAMERA, q MANUAL, s SYSTEM,
n CAMERA DISPLAY, o DSC, t VIDEO,
n VIDEO DISPLAY
1) Rotate the MENU Wheel to select the desired
function, and press it. The Sub Menu appears.
Example: m CAMERA Menu
VIDEO/MEMORY Switch
1 For Video and D.S.C. Recording Menus:
● Set the VIDEO/MEMORY Switch to “VIDEO”
or “MEMORY”.
● Set the Power Switch to “M” while pressing
down the Lock Button located on the switch.
Selected function
For Video Playback Menus:
CAMERA
REC MODE
–
● Set the VIDEO/MEMORY Switch to “VIDEO”.
● Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
● For D.S.C. Playback Menus, refer to “D.S.C.
PLAYBACK” (੬ pg. 24).
SOUND MODE– 1 2b i
t
ZOOM
–
–
–
4 0 x
FULL
AUTO
Selected menu icon blinks.
SNAP MODE
GA I N UP
A
NAV I GAT I ON– MANUAL
RETURN
2) Rotate the MENU Wheel
to select the desired
parameter.
Sub Menu
2 Open the LCD monitor fully, or pull out the
viewfinder fully.
CAMERA
REC MODE
–
3 Press the MENU Wheel in. The Menu Screen
appears.
Menu Screen for Video
and D.S.C. Recording
Menu
Menu Screen for Video
Playback Menu
RETURN
CAMERA
3) Press the MENU Wheel in.
Selection is complete.
● Repeat the procedure if
you wish to set other
function menus.
V I DEO
WI PE / FADER
FADER–WH I TE
FADER–BLACK
FADER–B .W
WI PE–CORNER
WI PE–WI NDOW
WI PE–SL I DE
WI PE–DOOR
WI PE–SCROLL
WI PE–SHUTTER
REC MODE
–
SOUND MODE– STEREO
SOUND MODE– 1 2b i
t
1 2b i
t
MODE– SOUND
1
ZOOM
–
–
–
4 0 x
SYNCHRO
–
–
0 .
0
SNAP MODE
GA I N UP
FULL
AUTO
REC MODE
A
COPY– OFF
NAV I GAT I ON– MANUAL
NAV I . DEL .
S / AV I NPUT
–
OFF
RETURN
RETURN
4 Rotate the MENU Wheel to select the desired
function, and press it. The selected function
menu appears.
5 Setting procedure hereafter depends on the
selected function.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT (cont.)
32
EN
RECORDING MENUS
WI PE / FADER
4) Press the MENU Wheel in.
The Menu Screen returns.
● Repeat the procedure if
you wish to set other
function menus.
FADER–WH I TE
FADER–BLACK
FADER–B .W
Wipe Or Fader Effects
IMPORTANT:
Some Wipe/Fader Effects cannot be used with
certain modes of Program AE with special effects.
(੬ pg. 33) If an unusable Wipe/Fader Effect is
selected, its indicator blinks in blue or goes out.
WI PE–CORNER
WI PE–WI NDOW
WI PE–SL I DE
WI PE–DOOR
WI PE–SCROLL
WI PE–SHUTTER
5) Press the MENU Wheel in
again. The Menu Screen
closes.
NOTES:
These effects let you make pro-style scene
transitions. Use them to spice up the transition from
one scene to the next.
● The “m” settings are effective when the Power
Switch is set to both “A” and “M”. However, the
menu settings can be changed only when the
Power Switch is set to “M”.
Wipe or Fader works when video recording is started
or stopped.
● The “q” settings are effective only when the
Power Switch is set to “M”.
● The “s” functions which are set when the Power
Switch is set to “M” are also applied when the
Power Switch is set to “PLAY”.
● The “n” (CAMERA DISPLAY) settings are
effective even when the Power Switch is set to
“A”. However, the menu settings can be changed
only when the Power Switch is set to “M”.
● The “n” (CAMERA DISPLAY) settings are
effective only for shooting except “BRIGHT”.
● The “n” (VIDEO DISPLAY) settings are effective
only for video playback except “BRIGHT”.
● The date indication can also be turned on/off by
pressing the DISPLAY Button on the remote
control (provided). (੬ pg. 22, 52, 61)
the Lock Button located on the switch.
3 Open the LCD monitor fully, or pull out the
viewfinder fully.
4 Set “v” to the desired mode. (੬ pg. 31)
5 To activate the Fade-in or Wipe-in, press FADE/
WIPE during Record-Standby mode.
● The selected effect indicator appears.
To activate the Fade-out or Wipe-out, press
FADE/WIPE during recording.
● The selected effect indicator appears.
6 Press the Recording Start/Stop Button to activate
the Fade-in/out or Wipe-in/out.
To deactivate the selected effect…
Press FADE/WIPE again in step 6. The effect
indicator disappears.
NOTE:
You can extend the length of a Wipe or Fader by
pressing and holding the Recording Start/Stop
Button.
WIPE/FADER
(Factory-preset: FADER–WHITE)
FADER–WHITE: Fade in or out with a white
screen.
FADER–BLACK: Fade in or out with a black
screen.
FADER–B.W: Fade in to a colour screen from a
black and white screen, or fade out from colour to
black and white.
WIPE – CORNER: Wipe in on a black screen
from the upper right to the lower left corner, or wipe
out from lower left to upper right, leaving a black
screen.
WIPE – WINDOW: The scene starts in the
centre of a black screen and wipes in toward the
corners, or comes in from the corners, gradually
wiping out to the centre.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
WIPE – SLIDE: Wipe in from right to left, or
SNOW: Compensates for subjects that may
otherwise appear too dark when shooting in
extremely bright surroundings such as in the snow.
wipe out from left to right.
WIPE – DOOR: Wipe in as the two halves of a
black screen open to the left and right, revealing the
scene, or wipe out and the black screen reappears
from left and right to cover the scene.
SPOTLIGHT: Compensates for subjects that
may otherwise appear too bright when shooting
under extremely strong direct lighting such as
spotlights.
WIPE – SCROLL: The scene wipes in from the
bottom to the top of a black screen, or wipes out
from top to bottom, leaving a black screen.
NOTE:
“SPOTLIGHT” has the same effect as –3 with the
exposure control. (੬ pg. 46)
WIPE – SHUTTER: Wipe in from the centre of
a black screen toward the top and bottom, or wipe
out from the top and bottom toward the centre
leaving a black screen.
TWILIGHT: Makes evening scenes look more
natural. White Balance (੬ pg. 34, 47) is
automatically set to “ ”, but can be changed to
camcorder automatically adjusts the focus from
approx. 10 m to infinity. From less than 10 m, adjust
the focus manually. The flash does not fire in this
mode.
Program AE With Special Effects
IMPORTANT:
Some modes of Program AE with special effects
cannot be used with certain Wipe/Fader effects.
(੬ pg. 32) If an unusable mode is selected, the
indicator of Wipe/Fader effects blinks or goes out.
SEPIA: Recorded scenes have a brownish tint
like old photos. Combine this with the Cinema
mode for a classic look.
MONOTONE: Like classic black and white
films, your footage is shot in B/W. Used together
with the Cinema mode, it enhances the “classic
film” effect.
1 Set the Power Switch to “M” while pressing down
the Lock Button located on the switch.
2 Open the LCD monitor fully, or pull out the
viewfinder fully.
CLASSIC FILM*: Gives recorded scenes a
strobe effect.
3 Set “r” to the desired mode. (੬ pg. 31)
4 Press PROG.AE to activate the selected effect.
STROBE*: Your recording looks like a series of
consecutive snapshots.
● The selected effect indicator appears.
To deactivate the selected effect…
Press PROG.AE again. The effect indicator
disappears.
MIRROR*: Creates a mirror image on the right
half of the screen, juxtaposed to the normal image
on the other half.
* Available only when the VIDEO/MEMORY Switch
is set to “VIDEO”.
NOTES:
● Program AE with special effects can be changed
during recording or during Record-Standby.
● Some modes of Program AE with special effects
cannot be used during Night-Scope.
PROGRAM AE
(Factory-preset: SHUTTER 1/50)
SHUTTER 1/50: The shutter speed is fixed at 1/
50th of a second. Black bands that usually appear
when shooting a TV screen become narrower.
SHUTTER 1/120: The shutter speed is fixed at
1/120th of a second. The flickering that occurs when
shooting under a fluorescent light or mercury-
vapour lamp is reduced.
SPORTS
(Variable Shutter Speed: 1/250 – 1/4000)
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable slow-
motion playback. The faster the shutter speed, the
darker the picture becomes. Use the shutter function
under good lighting conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
EN
RECORDING MENUS (cont.)
Zooming
ZOOM
White Balance Adjustment
(Factory-preset: 40X)
10X: When set to “10X” while using digital zoom,
the zoom magnification will reset to 10X since
digital zoom will be disengaged.
40X*: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 10X (the optical zoom
limit), to a maximum of 40X digital magnification.
300X*: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 10X (the optical zoom
limit), to a maximum of 300X digital
magnification.
W. BALANCE
For details, refer to “White Balance Adjustment”
(੬ pg. 47).
(Factory-preset: AUTO)
AUTO: White balance is adjusted automatically.
MWB: Adjust the white balance manually
when shooting under various types of lighting.
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
HALOGEN: A video light or similar type of
lighting is used.
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
Camera Menu
CAMERA
Snapshot mode for video recording
For details on the procedure, refer to “Snapshot (For
Video Recording)” (੬ pg. 42). There is the sound
effect of a shutter closing.
Recording mode
Allows you to set the recording mode (SP or LP)
depending on your preference.
SNAP MODE
FULL: Snapshot mode with no frame
NEGA: Nega mode
(Factory-preset: FULL)
REC MODE
(Factory-preset: SP)
PIN-UP: Pin-Up mode
SP: Standard Play
FRAME: Snapshot mode with frame
LP: Long Play—more economical, providing 1.5
times the recording time.
NOTES:
● Audio Dubbing (੬ pg. 58) and Insert Editing
(੬ pg. 59) are possible on tapes recorded in the
SP mode.
FULL
NEGA
PIN-UP
FRAME
● If the recording mode is switched during
recording, the playback picture will be blurred at
the switching point.
● It is recommended that tapes recorded in the LP
mode on this camcorder be played back on this
camcorder.
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there
may be momentary pauses in the sound.
Sound mode
SOUND MODE
(Factory-preset: 12 bit)
12 bit: Enables video recording of stereo sound
on four separate channels, and is recommended
for use when performing Audio Dubbing.
(Equivalent to the 32 kHz mode of previous
models)
16 bit: Enables video recording of stereo sound
on two separate channels. (Equivalent to the 48
kHz mode of previous models)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
35
Gain up
GAIN UP
Manual Menu
MANUAL
(Factory-preset: AGC)
OFF: Allows you to shoot dark scenes with no
picture brightness adjustment.
AGC: The overall appearance may be grainy, but
the image is bright.
Digital Image Stabilisation
AUTO
: The shutter speed is automatically
To compensate for unstable images caused by
adjusted. Shooting a subject in low or poor
lighting at slow shutter speed provides a brighter
image than in the AGC mode, but the subject’s
movements are not smooth or natural. The overall
appearance may be grainy. While the shutter
camera-shake, particularly at high magnification.
DIS (Factory-preset: ON)
NOTES:
● Accurate stabilisation may not be possible if hand
shake is excessive, or under the following
conditions:
• When shooting subjects with vertical or
horizontal stripes.
• When shooting dark or dim subjects.
• When shooting subjects with excessive
backlighting.
speed is being automatically adjusted, “
displayed.
” is
Navigation time
NAVIGATION
5SEC / 15SEC / 30SEC / 60SEC:
The captured image is stored in the memory card
as a thumbnail image when the recording time is
over the navigation time.
(Factory-preset: MANUAL)
• When shooting scenes with movement in
various directions.
For example, “5SEC” is suitable to record short
scenes with the thumbnail images. (੬ pg. 48)
However, the stored thumbnail images may take
up a lot of memory. In this case, using the
memory card with large capacity is
• When shooting scenes with low-contrast
backgrounds.
● Switch off this mode when recording with the
camcorder on a tripod.
● The “
” indicator blinks or goes out if the
recommended.
Stabiliser cannot be used.
MANUAL: Enables thumbnail images to be made
manually. (੬ pg. 48)
Self-Timer
For details, refer to “Self-Timer” (੬ pg. 44).
SELF-TIMER
(Factory-preset: OFF)
OFF / ON
Download from Www.Somanuals.com. All Manuals Search And Download.
36
EN
RECORDING MENUS (cont.)
During playback on wide-screen TVs, the black
bands at the top and bottom of the screen are cut
and the screen ratio becomes 16:9. When using
this mode, refer to your wide-screen TV’s
instruction manual. During playback/recording on
4:3 TVs/LCD monitor/viewfinder, black bands are
inserted at the top and bottom of the screen and
the image appears like a letter boxed 16:9 movie.
SQUEEZE* : For playback on TVs with an
aspect ratio of 16:9. Naturally expands the image
to fit the screen without distortion. The
indicator appears. When using this mode, refer to
your wide-screen TV’s instruction manual. During
playback/recording on 4:3 TVs/LCD monitor/
viewfinder, the image is elongated vertically.
5-Second Recording
Record a vacation or an important event in 5-second
clips to keep the action moving. This function is
available only for video recording.
1 Set “5S” to “5S”. (੬ pg. 31)
● “5S” appears.
2 Press the Recording Start/Stop Button to start
recording, and after 5 seconds the camcorder
enters Record-Standby mode automatically.
● Even if you press the Recording Start/Stop
Button again within 5 seconds after recording
starts, Record-Standby mode is not engaged.
3 To exit the 5S mode, select “OFF” in step 1.
To take a snapshot in the 5-second recording
mode…
Instead of pressing the Recording Start/Stop Button
in step 2, select the desired Snapshot mode in
CAMERA Menu (੬ pg. 34), then press SNAPSHOT.
The camcorder records a 5-second still. When “5S”
is set to “Anim.”, this function is not available.
D.WIDE* : The
indicator appears. The
zoom range is extended beyond the maximum
optical zoom wide angle range. This mode’s wide
angle setting is equivalent to using a 0.7X wide
conversion lens. Zooming is possible from 0.7X to
a magnification set in CAMERA Menu. This mode
is suitable for shooting in a small room.
5S
(Factory-preset: OFF)
OFF: Disables 5-Second Recording.
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
5S: Enables 5-Second Recording.
Anim.: Allows you to record a few frames only. By
using an inanimate object and changing its
position between shots, you can record the
subject as though it is moving.
Wind cut
WIND CUT
OFF: Disengages the function.
(Factory-preset: OFF)
ON
: Helps cut down on noise created by
NOTE:
wind. The “ ” indicator appears. The quality of
the sound will change. This is normal.
When “5S” is set to “Anim.”, the 5-Second
Recording mode is not available. Animation
recording of a few frames only is taken instead.
Maximum telephoto setting
Usually the distance to a subject where the lens is in
focus depends on the zoom magnification. Unless
there is a distance more than 1 m to the subject, the
lens is out of focus at the maximum telephoto
setting.
TELE MACRO
(Factory-preset: OFF)
OFF: Disables the function.
ON: When set to “ON”, you can shoot a subject
as large as possible at a distance of approx.
60 cm.
NOTE:
Depending on the zoom position, the lens may go
out of focus.
Wide mode
WIDE MODE
(Factory-preset: OFF)
OFF: Records with no change in the screen ratio.
For playback on a TV with a normal screen ratio.
CINEMA* : Inserts black bands at the top and
bottom of the screen. The
indicator appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
37
Snapshot flash
B-IN FLASH
OFF: Will not fire.
AUTO: Fires automatically if it is dark ( appears).
AUTO C: Fires automatically if it is dark (
appears) and reduces the Red-Eye effect in the
subject’s eyes.
For details, refer to “USING THE REMOTE
(Factory-preset: AUTO)
CONTROL UNIT” (੬ pg. 56).
REMOTE
(Factory-preset: ON)
OFF: Disables the remote control operations.
ON: Enables the remote control operations.
ON: Always fires.
Automatic demonstration mode
Demonstrates certain functions such as Program AE
with special effects, etc., and can be used to confirm
how these functions operate. (੬ pg. 9)
Flash brightness adjustment
FLASH ADJ.
For details, refer to “Flash Brightness Adjustment”
(੬ pg. 43).
(Factory-preset: 0)
DEMO MODE
(Factory-preset: ON)
OFF: Automatic demonstration will not take
place.
ON: Demonstrates certain functions such as
Program AE with special effects, etc., and can be
used to confirm how these functions operate.
Demonstration starts in the following cases:
•When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
System Menu
SYSTEM
•With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch is set to “A” or “M”.
Beep, melody and shutter sound
BEEP
(Factory-preset: MELODY)
Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for more
than 3 minutes after that, the demonstration will
resume.
OFF: Even though not heard while shooting,
shutter sound is recorded on the tape.
BEEP: The beep sounds when the power is turned
on or off, and at the beginning and end of
recording. It also activates the shutter sound
effect. (੬ pg. 23, 42)
MELODY: Instead of a beep, a melody sounds
when any operation is performed. It also activates
the shutter sound effect. (੬ pg. 23, 42)
NOTES:
● If a cassette is in the camcorder, the demonstration
cannot be turned on.
● “DEMO MODE” remains “ON” even if the
camcorder power is turned off.
● If “DEMO MODE” remains “ON”, some functions
will not be available. After viewing demo, set to
“OFF”.
Tally lamp setting
TALLY
(Factory-preset: ON)
OFF: The tally lamp remains off at all times.
ON: The tally lamp comes on to signal the start of
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
EN
RECORDING MENUS (cont.)
INFO LCD setting
INFO LCD
Display Menu
(Factory-preset: ON)
OFF: The shooting information does not appear.
the INFO LCD.
CAMERA DISPLAY
Brightness adjustment of the display
BRIGHT
For details, refer to “Brightness Adjustment Of The
Display” (੬ pg. 13).
Title impose
For details, refer to “Title Impose” (੬ pg. 51).
TITLE W/
(Factory-preset: BACKGRND)
BACKGRND: Superimposes the title/frame over
images.
Display setting
ON SCREEN
IMAGE: Superimposes the title/frame with its
white background.
(Factory-preset: LCD/TV)
LCD: Keeps the camcorder’s display (except the
date, time and time code) from appearing on the
connected TV screen.
LCD/TV: Makes the camcorder’s display appear
on screen when the camcorder is connected to a
TV.
E-Mail Clip Recording
For details, refer to “E-Mail Clip Recording”
(੬ pg. 50).
E-CLIP REC
160 x 120
240 x 176
(Factory-preset: 240 x 176)
Date and time display setting
DATE/TIME
(Factory-preset: AUTO)
Priority setting
When the viewfinder is pulled out while the LCD
monitor is opened, you can select which one to use.
OFF: The date/time does not appear.
AUTO: Displays the date/time for approx.
5 seconds when the Power Switch is set from
“OFF” to “A” or “M”.
PRIORITY
(Factory-preset: LCD)
LCD: Allows you to use the LCD monitor.
FINDER: Allows you to use the viewfinder.
Time code setting
TIME CODE
OFF: Time code is not displayed.
ON: Time code is displayed on the camcorder
and on the connected TV. Frame numbers are not
displayed during recording.
(Factory-preset: OFF)
Resetting menu settings
CAM RESET
EXECUTE: Resets all settings to the factory-preset.
RETURN: Does not reset all settings to the factory-
preset.
Clock adjustment
CLOCK ADJ.
Allows you to set the current date and time.
(੬ pg. 14)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
39
MultiMediaCard
DSC Menu
DSC
Image Size/Picture Quality
8 MB* 16 MB* 32 MB*
640 x 480/FINE
55
190
25
75
16
50
10
34
105
320
50
215
645
100
320
60
640 x 480/STANDARD
1024 x 768/FINE
Picture quality
The Picture Quality mode can be selected to best
match your needs. Two Picture Quality modes are
available: FINE (
of quality).
1024 x 768/STANDARD
1280 x 960/FINE
160
32
) and STANDARD (
) (in order
1280 x 960/STANDARD
1600 x 1200/FINE
105
21
215
42
QUALITY
FINE / STANDARD
(Factory-preset: FINE)
1600 x 1200/STANDARD
65
135
NOTE:
*
Optional
The number of storable images depends on the
selected picture quality as well as the composition
of the subjects in the images and the type of memory
card being used.
** Provided (9 title images pre-stored)
Recording media selection
REC SELECT
: When Snapshot recording is performed
with the VIDEO/MEMORY Switch set to
“VIDEO”, still images are recorded only onto the
tape.
(Factory-preset:
)
Image size
The Image Size mode can be selected to best match
your needs.
IMAGE SIZE
640 x 480 / 1024 x 768 / 1280 x 960 /
1600 x 1200
(Factory-preset: 1280 x 960)
/
: When Snapshot recording is
performed with the VIDEO/MEMORY Switch set
to “VIDEO”, still images are recorded not only
onto the tape but also in the memory card
(640 x 480 pixels). In this mode, the “SNAP
MODE” selection in CAMERA Menu is also
applicable to memory card recording.
NOTE:
The settings can be changed only when the VIDEO/
MEMORY Switch is set to “MEMORY”.
Approximate Number of Storable Images
Image Size/
Picture
Quality
SD Memory Card
8 MB** 8 MB* 16 MB* 32 MB* 64 MB*
640 x 480/
FINE
42
140
19
60
12
40
7
47
160
21
65
13
45
8
95
295
47
205
625
95
425
1285
200
640
125
425
80
640 x 480/
STANDARD
1024 x 768/
FINE
1024 x 768/
STANDARD
145
29
310
60
1280 x 960/
FINE
1280 x 960/
STANDARD
95
205
41
1600 x 1200
/FINE
19
1600 x 1200
/STANDARD
25
28
60
130
275
Download from Www.Somanuals.com. All Manuals Search And Download.
40
EN
PLAYBACK MENUS
Synchro adjustment
Video Menu
VIDEO
For details, refer to “For More Accurate Editing”
(੬ pg. 64).
SYNCHRO
(Factory-preset: 0.0)
Recording mode
Playback sound
Allows you to set the video recording mode (SP or
LP) depending on your preference. It is
During tape playback, the camcorder detects the
sound mode in which the recording was made, and
plays the sound back. Select the type of sound to
accompany your playback picture. According to the
menu access explanation on page 31, select
“SOUND MODE” or “12bit MODE” from the Menu
Screen and set it to the desired parameter.
recommended you use “REC MODE” in VIDEO
Menu when using this camcorder as a recorder
during dubbing. (੬ pg. 52, 54)
REC MODE
SP / LP
(Factory-preset: SP)
SOUND MODE
STEREO
channels in stereo.
SOUND L : Sound from the “L” channel is
output.
SOUND R : Sound from the “R” channel is
output.
(Factory-preset: STEREO
: Sound is output on both “L” and “R”
)
NOTE:
set to “PLAY” or “M”.
Dubbing from tape to memory card
COPY
(Factory-preset: OFF)
OFF: Enables snapshots to be taken during tape
12bit MODE
(Factory-preset: SOUND 1)
playback.
MIX: Original and dubbed sounds are combined
and output in stereo on both “L” and “R”
channels.
ON: Enables dubbing of images recorded on a
tape to a memory card. (੬ pg. 55)
SOUND 1: Original sound is output on both “L”
Deleting thumbnail images
and “R” channels in stereo.
SOUND 2: Dubbed sound is output on both “L”
and “R” channels in stereo.
For details, refer to “To delete thumbnail images”
(੬ pg. 49).
NAVI.DEL.
NOTES:
● The “SOUND MODE” setting is available for both
12-bit and 16-bit sound. (In previous models’
functions, “12-bit” is called “32 kHz” and “16-bit”
is called “48 kHz”.)
● The camcorder cannot detect the sound mode in
which the recording was made during fast-forward
or rewind. During playback the sound mode is
displayed in the upper left corner.
IMAGE SEL. / TAPE SEL. / ALL / RETURN
S-Video/AV input
S/AV INPUT
(Factory-preset: OFF)
OFF: Enables audio/video signal output to a TV,
VCR, etc. via the AV and S-Video connectors.
(੬ pg. 22, 52)
ON: Enables audio/video signal input from the AV
and S-Video connectors. (੬ pg. 52)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
41
TIME CODE
OFF / ON
(Factory-preset: OFF)
System Menu
NOTE:
SYSTEM
The date indication can also be turned on/off by
pressing the DISPLAY Button on the remote control
(provided). (੬ pg. 22, 52, 61)
Each setting is linked with “s”, which appears
when the Power Switch is set to “M”. (੬ pg. 31) The
parameters are the same as in the description on
page 37.
Display
4
12b i
L
t
/ SOUND1
ON SCREEN Setting:
For playback sound, tape
speed and tape running
during video playback.
BEEP
OFF / BEEP / MELODY
TALLY
OFF / ON
REMOTE
OFF / ON
(Factory-preset: MELODY)
(Factory-preset: ON)
(Factory preset: ON)
DATE/TIME Setting:
For date/time.
DEMO MODE
OFF / ON
(Factory-preset: ON)
INFO LCD
(Factory-preset: ON)
OFF / ON
2 5 . 12 .03
17 :3 0
TITLE W/
BACKGRND / IMAGE
E-CLIP REC
(Factory-preset: BACKGRND)
(Factory-preset: 240 x 176)
TIME CODE Setting:
For time code.
160 x 120 / 240 x 176
PRIORITY
LCD / FINDER
(Factory-preset: LCD)
Minutes
Seconds
Frames*
CAM RESET
EXECUTE / RETURN
12 : 34 : 24
* 25 frames = 1 second
Display Menu
VIDEO DISPLAY
The parameters (except “OFF” in ON SCREEN
settings) are the same as in the description on
page 38.
Brightness adjustment of the display
BRIGHT
For details, refer to “Brightness Adjustment Of The
Display” (੬ pg. 13).
ON SCREEN
(Factory-preset: LCD)
OFF / LCD / LCD/TV
When set to “OFF”, the camcorder’s display
disappears.
DATE/TIME
(Factory-preset: OFF)
OFF / AUTO / ON
When set to “AUTO”, the date/time are displayed
in the following cases:
•When playback starts. The camcorder displays
the date/time when scenes are recorded.
Download from Www.Somanuals.com. All Manuals Search And Download.
•When the date is changed during playback.
42
EN
Snapshot (For Video Recording)
SNAPSHOT Button
This feature lets you record still images that look like
photographs onto a tape.
Power Switch
1 Set the VIDEO/MEMORY Switch to “VIDEO”.
Lock Button
2 Set the Power Switch to “M” while pressing down
NIGHT Button
the Lock Button located on the switch.
3 Open the LCD monitor fully, or pull out the
viewfinder fully.
4 Set “SNAP MODE” to the desired mode.
(੬ pg. 31, 34)
5 Press SNAPSHOT.
image will be recorded for approx. 6 seconds,
then the camcorder re-enters the Record-
Standby mode.
● You can perform Snapshot also during
recording. A still image will be recorded for
approx. 6 seconds, then the normal recording
resumes.
or “M”), Snapshot recording takes place using
the selected Snapshot mode.
VIDEO/MEMORY Switch
Night Scope
Makes dark subjects or areas even brighter than they
would be under good natural lighting. Although the
recorded image is not grainy, it may look as if it is
strobing due to the slow shutter speed.
NOTES:
● To remove the shutter sound, refer to “BEEP” on
page 37.
1 Set the Power Switch to “M” while pressing down
the Lock Button located on the switch.
● If Snapshot recording is not possible, the “O”
indication blinks when SNAPSHOT is pressed.
● If Program AE with special effects (੬ pg. 33) is
engaged, certain modes of Program AE with
special effects are disabled during Snapshot
recording. In such a case, the icon blinks.
● During playback as well, all snapshot modes are
2 Open the LCD monitor fully or pull out the
viewfinder fully.
“
” appears.
provide up to 30 times sensitivity.
● “ ” appears beside “
” while the shutter
speed is being automatically adjusted.
available when “
COPY” is set to “OFF”
To deactivate Night-Scope…
Press NIGHT again so that the Night-Scope
indicator disappears.
in VIDEO Menu. (੬ pg. 40) However, the shutter
sound is not heard.
● During Snapshot recording, the image displayed
in the viewfinder may be partially missing.
However, there is no effect in the recorded image.
● When a cable is connected to the AV connector,
the shutter sound is not heard from the speaker,
however it is recorded onto the tape.
NOTES:
● During Night-Scope, the following functions or
settings cannot be activated and its indicator
blinks or goes out:
• Some modes of “Program AE With Special
Effects” (੬ pg. 33).
• “Snapshot Flash” (੬ pg. 43)
• “GAIN UP” in CAMERA Menu. (੬ pg. 35)
• “DIS” in MANUAL Menu. (੬ pg. 35)
● During Night-Scope, it may be difficult to bring
the camcorder into focus. To prevent this, use of a
tripod is recommended.
Motor Drive Mode
Keeping SNAPSHOT pressed in step 5 provides an
effect similar to serial photography. (Interval
between still images: approx. 1 second)
● The Motor Drive mode is disabled when “REC
SELECT” is set to “
/
”. (੬ pg. 39)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
43
Snapshot Flash
When a snapshot (੬ pg. 23, 42) is taken in the dark
the camcorder fires the flash and adjusts the
flash brightness manually. When you find that the
snapshots you took look too bright or too dark,
adjust it manually.
Flash
1 Select “FLASH ADJ.” in MANUAL Menu, and
press the MENU Wheel in.
● The parameter appears.
2 To intensify the flash, rotate the MENU Wheel
towards “+”. To weaken the flash, rotate the
MENU Wheel towards “–”.
The flash can be used when a snapshot is taken in
Record-Standby mode. (੬ pg. 23, 42)
● When the Power Switch is set to “A”, the flash
automatically pops up and fires if it is dark (
appears).
● When the Power Switch is set to “M”, you can
select the flash setting. (੬ pg. 31, 37)
● Adjustment range: –3 to +3.
3 Press the MENU Wheel in. Rotate the MENU
Wheel to select “BRETURN”, and press it twice
to close the Menu Screen.
If “AUTO C” is selected...
NOTE:
The C Red-Eye reduction indicator lights. Press
SNAPSHOT. The flash fires twice. The first flash is
for reduction of the human eye’s red reflection and
the second flash is for the actual recording.
When you change the subject you are shooting or
the shooting location, set it back to 0 as described
in step 2 and take a snapshot to check the flash
brightness. After doing this adjust to your desired
brightness.
After shooting...
Be sure to close the flash by pressing it softly until it
locks.
NOTES:
● Do not fire the flash at a person at short range.
● When the optional video light is attached, it is not
possible to use the built-in flash.
● The flash does not fire when the flash is set to
“OFF” or when Night-Scope mode (੬ pg. 42) is
engaged, and also when the battery remaining
power is low.
● Although images shot with a flash tend to look
whiter than they actually are, to compensate for
this the camcorder automatically darkens the
picture when using the flash. When shooting a
subject at a distance where the flash light cannot
reach (over approx. 2 m), set the flash to “OFF” to
prevent the picture from becoming too dark or
becoming too tinted.
● The colour tone changes depending on the
background lighting conditions, such as under
fluorescent or halogen lamps.
● While charging the flash, blinks and the flash
will not fire. Although noise may appear, this is
not a malfunction and is not recorded. It can take
up to 10 seconds to charge the flash.
● Do not open the flash unit manually or apply an
unreasonable amount of pressure to it. Doing so
may cause its position to be changed, making it
impossible to shoot with the correct brightness.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
EN
FEATURES FOR RECORDING (cont.)
NOTE:
SNAPSHOT Button
If “BEEP” and “TALLY” are set to “OFF” (੬ pg. 37),
the beep does not sound and the tally lamp does not
light.
Lock Button
Power Switch
When the Recording Start/Stop Button or
SNAPSHOT is pressed, the tally lamp changes as
shown:
Begins blinking
(Self-Timer starts)
FOCUS Button
Manual Focus Ring
Blinks quickly
(Self-Timer shooting starts
soon)
Self-Timer
Once the camcorder is set, the camcorder operator
can become part of the scene in a more natural way,
adding the final touch to a memorable picture.
1 Set the Power Switch to “M” while pressing down
Stops blinking and stays on
(Self-Timer video recording
starts)
After approx.
15 sec.
the Lock Button located on the switch.
2 Open the LCD monitor fully, or pull out the
OR
viewfinder fully.
Turns off
(Self-Timer snapshot
recording occurs)
● You can tilt the LCD monitor upward to 180°
so that it faces forward and view yourself while
self-recording with the viewfinder pushed
back.
MANUAL
3 Set “SELF-TIMER” to
SELF–T I MER
–
OFF
ON
“ON ”. (੬ pg. 31, 35)
4 To engage the Self-Timer
for video recording, press
the Recording Start/Stop
Button.
RETURN
● After 15 seconds, the
beep sounds and video
recording starts.
5 To stop Self-Timer
recording, press the
Recording Start/Stop
Button again.
Self-Timer indication
● The camcorder re-enters
Record-Standby mode.
OR
5 Press SNAPSHOT.
● After 15 seconds, the beep sounds and
snapshot recording starts. After that, the
camcorder re-enters Record-Standby mode.
6 To end Self-Timer recording, select “OFF” in
step 3.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
45
Auto Focus
Manual Focus
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as close
as approx. 5 cm to the subject) to infinity.
NOTE:
If you are using the viewfinder, you should already
have performed “Viewfinder Adjustment”
(੬ pg. 12).
Focus detection zone
1 Set the Power Switch to “M” while pressing down
the Lock Button located on the switch.
2 Press FOCUS. The manual focus indicator
appears.
3 To focus on a further subject, rotate the Manual
Focus Ring clockwise. The “ ” indicator appears
and blinks.
However, correct focus may not be obtainable in the
situations listed below (in these cases perform
“Manual Focus”):
● When two subjects overlap in the same scene.
● When illumination is low.*
While focusing on a
further subject
● When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-
colour wall, or a clear, blue sky.*
Manual focus
indicator
● When a dark object is barely visible in the LCD
monitor or the viewfinder.*
To focus on a nearer subject, rotate the Manual
Focus Ring counterclockwise. The “ ” indicator
appears and blinks.
● When the scene contains minute patterns or
identical patterns that are regularly repeated.
● When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
● When shooting a scene with a high-contrast
background.
While focusing on a
nearer subject
* The following low-contrast warnings appear
Manual focus
indicator
blinking:
,
,
and
NOTES:
● If the lens is smeared or blurred, accurate focusing
is not possible. Keep the lens clean. (੬ pg. 77)
When condensation occurs, wipe with a soft cloth
or wait for it to dry naturally.
● When shooting a subject close to the lens, zoom
out first. (੬ pg. 18) If zoomed-in in the auto focus
mode, the camcorder may automatically zoom
out depending on the distance between the
camcorder and the subject. This will not occur
when “TELE MACRO” is set to “ON”. (੬ pg. 36)
To reset to Auto Focus...
Press FOCUS or set the Power Switch to “A”.
NOTES:
● Be sure to focus the lens in the maximum
telephoto position when you use the Manual
Focus mode. If you focus in on a subject in the
wide-angle position, sharply focused images
cannot be obtained when zoomed up because the
depth-of-field is reduced at longer focal lengths.
● When the focus level cannot be adjusted any
further or closer, “ ” or “ ” will blink.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
EN
FEATURES FOR RECORDING (cont.)
Iris Lock
EXPOSURE Button
MENU Wheel
Like the pupil of the human eye, the iris contracts in
well-lit environments to keep too much light from
entering, and dilates in dim environments to allow
in more light.
Use this function in the following situations:
● When shooting a moving subject.
● When the distance to the subject changes (so its
size in the LCD monitor or the viewfinder
changes), such as when the subject is backing
away.
● When shooting on a reflective natural background
such as at the beach or when skiing.
● When shooting objects under a spotlight.
● When zooming.
Lock Button
Power Switch
Exposure Control
Manual exposure control is recommended in the
following situations:
● When shooting using reverse lighting or when the
background is too bright.
● When shooting on a reflective natural background
such as at the beach or when skiing.
● When the background is overly dark or the subject
is bright.
When the subject is close, keep the iris locked. Even
when the subject moves away from you, the image
will not darken or brighten.
the Lock Button located on the switch.
1 Set the Power Switch to “M” while pressing down
viewfinder fully.
the Lock Button located on the switch.
3 Press EXPOSURE.
2 Open the LCD monitor fully, or pull out the
● The exposure control indicator appears.
viewfinder fully.
4 Adjust zoom so that the subject fills the LCD
monitor or the viewfinder, then press and hold
the MENU Wheel for over 2 seconds. The
3 Press EXPOSURE.
● The exposure control indicator appears.
4 To brighten the image, rotate the MENU Wheel
towards “+”. To darken the image, rotate the
MENU Wheel towards “–”. (maximum 6)
● +3 exposure has the same effect as the
exposure control indicator and the “
indication appear.
5 Press the MENU Wheel in.
The “ ” indication
changes to “ ” and the iris
is locked.
is set to “SPOTLIGHT”. (੬ pg. 33)
3
To return to automatic iris
control...
Press EXPOSURE twice. Or, set
the Power Switch to “A”.
● The exposure control
indicator and “ ” disappear.
5 Press the MENU Wheel in. Exposure adjustment
is complete.
Iris Lock Indicator
To return to automatic exposure control...
Press EXPOSURE twice. Or, set the Power Switch to
“A”.
● If EXPOSURE is pressed once, the camcorder will
enter the exposure control mode again.
To lock the exposure control and the iris…
After step 3 of “Exposure Control”, adjust the
exposure by rotating the MENU Wheel. Then lock
the iris in steps 4 and 5 of “Iris Lock”. For automatic
locking, press EXPOSURE twice in step 3. The
exposure control and the iris become automatic.
NOTES:
● You cannot use the manual exposure control at the
same time when “r” is set to “SPOTLIGHT” or
“SNOW” (੬ pg. 33), or with the backlight
compensation. (੬ pg. 47)
● If the adjustment does not cause any visible
change in brightness, set “GAIN UP” to “AUTO”.
(੬ pg. 31, 35)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
47
Backlight Compensation
Manual White Balance Adjustment
Backlight compensation
brightens the subject
quickly.
Press BACK LIGHT. The
indicator is displayed
and the subject is
Adjust the white balance manually when shooting
under various types of lighting.
Lock Button
White paper
BACK LIGHT Button
MENU Wheel
brightened. If pressed
again, disappears and
the brightness returns to the previous level.
● Using the BACK LIGHT Button may cause the light
around the subject to become too bright and the
subject to become white.
Power Switch
● Backlight compensations is also available when
the Power Switch is set to “A”.
1 Set the Power Switch to “M” while pressing down
White Balance Adjustment
The white balance that refers to the correctness of
colour reproduction under various lighting. If the
white balance is correct, all other colours will be
accurately reproduced.
the Lock Button located on the switch.
viewfinder fully.
3 Set “u” to “MWB”. (੬ pg. 31, 34)
● The
indication blinks slowly.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators
professional colour/tint reproduction.
subject. Adjust zoom or position yourself so that
the white paper fills the screen.
5 Press the MENU Wheel in until
begins
(Factory-preset: AUTO)
blinking rapidly.
When the setting is completed,
normal blinking.
resumes
AUTO: White balance is adjusted automatically.
when shooting under various types of lighting.
(੬ “Manual White Balance Adjustment”)
Screen closes and the Manual White Balance
indicator
is displayed.
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
● In step 4, it may be difficult to focus on the white
paper. In such a case, adjust focus manually.
(੬ pg. 45)
HALOGEN: A video light or similar type of
lighting is used.
● For the setting, refer to “Changing The Menu
Settings” (੬ pg. 31).
● The selected mode indicator except “AUTO”
appears.
● A subject can be shot under various types of
lighting conditions indoors (natural, fluorescent,
candlelight, etc.). Because the colour temperature
is different depending on the light source, the
subject tint will differ depending on the white
balance settings. Use this function for a more
natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off or
the battery removed.
To return to automatic white balance…
Set “u” to “AUTO”. (੬ pg. 31, 34) Or, set the
Power Switch to “A”.
NOTE:
White balance cannot be used when “r” is set to
“SEPIA” or “MONOTONE”. (੬ pg. 33)
Download from Www.Somanuals.com. All Manuals Search And Download.
48
EN
FEATURES FOR RECORDING (cont.)
7 Press the Recording Start/Stop Button to stop
NAVIGATION Function
The Navigation Function helps you check tape
contents by making thumbnail images on a memory
card.
recording.
To make thumbnail images after video recording
manually...
1) Perform steps 1 to 4 above.
2) Set “NAVIGATION” to “MANUAL”.
(੬ pg. 31, 35)
3) After the recording, press NAVI STORE.
•The “ ” indicator appears briefly and the
captured image is stored in the memory card as
a thumbnail image.
MENU Wheel
Power Switch
Lock Button
Rewind Button (3)
VIDEO/MEMORY Switch
NOTES:
● The remaining number of storable thumbnail
images also appears on the screen when it reaches
10 or less. If “REC SELECT” is set to “
/
”
in DSC Menu, the number shows how many
640 x 480 pixel images can be stored.
● If “5S” is set to “5S” or “Anim.” in MANUAL
Menu, the NAVIGATION function will not work
properly.
NAVI Button
NAVI STORE Button
To find scenes on tape using thumbnail images
(NAVIGATION Search)
Fast-Forward Button (5)
To make thumbnail images during video
recording automatically
1 Load a cassette. (੬ pg. 15)
2 Load a memory card. (੬ pg. 16)
3 Set the VIDEO/MEMORY switch to “VIDEO”.
4 Set the Power Switch to “PLAY” while pressing
1 Load a cassette. (੬ pg. 15)
down the Lock Button located on the switch.
2 Load a memory card. (੬ pg. 16)
3 Set the VIDEO/MEMORY Switch to “VIDEO”.
5 Press NAVI during video playback or stop mode.
● The loaded cassette’s
NAVIGATION thumbnail
image screen appears.
NAV I GAT I ON
4 Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
DATE : 24 . 2 5 ’ 0 3
3 : 3 : 2 9
TC
:
1 3 : 2 3 : 1 5
2
1
3
● Press 3 to display the
previous page. Press 5
to display the next page.
4
5
5 Set “NAVIGATION” to the desired navigation
storing time. (੬ pg. 31, 35)
● If the “
” indicator appears blinking on the
6 Rotate the MENU Wheel to select the desired
screen, wait until it stops blinking. If it does not
stop blinking after a while, check if a memory
card is loaded.
image, and press it.
● The “NAVIGATION SEARCH” indication
appears blinking and the camcorder starts
searching the tape for the relevant point of the
selected thumbnail image.
6 Press the Recording Start/Stop Button to start
recording.
1hh
01mm
● When the recording time
To cancel NAVIGATION search midway...
Press 4/9, 3, 5 or 8.
PAUSE
is over the navigation
time set in step 5, “
”
appears briefly, then the
image of the point where
recording is started is
captured and stored in
the memory card as a
thumbnail image.
Displayed while the
captured image is
being stored in the
memory card.
● If the Recording Start/
Stop button is pressed
before “
” stops
blinking, the image of the point where the
loaded memory card is recognised is captured.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
49
NOTE:
To add thumbnail images during video
playback
Once images are deleted, they cannot be restored.
Check images before deleting.
1 Perform steps 1 to 4 in “To find scenes on tape
IMPORTANT:
using thumbnail images (NAVIGATION Search)”.
● Be sure to always use the same tape and memory
card together as they were during recording;
otherwise, the camcorder cannot recognise Tape
and Memory Card IDs to perform NAVIGATION
function properly.
2 Press 4/9 to start video playback.
3 Press NAVI STORE at the desired point.
● The “ ” indicator appears briefly and the
image of the point where NAVI STORE is
pressed is stored in the memory card as a
thumbnail image.
● Check if an appropriate tape and memory card are
loaded when the following messages appear: “NO
ID ON TAPE OR CARD”, “UNABLE TO USE
NAVIGATION”, “THIS MEMORY CARD IS NOT
COMPATIBLE”.
● If you change the memory card while shooting on
one tape, two memory cards will share the tape’s
thumbnail images. We recommend that you use
one memory card for one tape.
● NAVIGATION Search does not work if the current
position is at a blank portion on the tape. Also, do
not leave a blank portion partway through the tape
when shooting; otherwise, NAVIGATION function
does not work properly.
● Before shooting newly over a recorded tape, be
sure to delete all thumbnail images of the previous
recording from the relevant memory card.
● If you copy thumbnail images from one memory
card to another via a PC, NAVIGATION Search
does not work with the copied memory card.
To delete thumbnail images
1 Load a memory card. (੬ pg. 16)
2 Set the VIDEO/MEMORY switch to “VIDEO”.
3 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
4 Press the MENU Wheel in. The Menu Screen
appears.
5 Rotate the MENU Wheel to select “t”, and
press it. The VIDEO Menu appears.
V I DEO
6 Rotate the MENU Wheel to
SOUND MODE– STEREO
1 2b i
t
MODE– SOUND
1
select “NAVI.DEL.”, and
press it. The Sub Menu
appears.
SYNCHRO
–
–
0 . 0
REC MODE
COPY– OFF
NAV I . DEL .
S / AV I NPUT
–
OFF
7 By rotating the MENU
RETURN
Wheel...
Select “IMAGE SEL.” to delete the currently
displayed thumbnail image.
Select “TAPE SEL.” to delete all thumbnail images
for the tape which contains the currently
displayed image.
Select “ALL” to delete all thumbnail images
stored in the memory card at once.
NAV I GAT I ON
8 Press the MENU Wheel in.
DELETE CURRENT?
The NAVIGATION screen
appears.
2 6 .12 . 0 3
EXECUTE
RETURN
1 5 : 0 0
9 Rotate the MENU Wheel to
select “EXECUTE”, and
press it.
● Press 3 to display the previous page. Press
5 to display the next page.
● To cancel deletion, select “RETURN”.
● Thumbnail images cannot be deleted during
video playback.
CAUTION:
Do not remove the memory card or perform any
other operation (such as turning off the camcorder)
during deletion. Also, be sure to use the provided
AC Power Adapter/Charger, as the memory card may
be corrupted if the battery becomes exhausted
during deletion. If the memory card becomes
corrupted, initialise it.
Download from Www.Somanuals.com. All Manuals Search And Download.
50
EN
FEATURES FOR RECORDING (cont.)
To make video clips from real-time camera
image
E-Mail Clip Recording
You can make video clips from real-time camera
image or recorded video footage and store them in a
memory card as files which can be conveniently
sent via E-Mail.
1 Load a memory card. (੬ pg. 16)
2 Set the VIDEO/MEMORY Switch to “MEMORY”.
3 Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
Power Switch
4 Set “E-CLIP REC” to the desired image size.
(੬ pg. 31, 38)
Lock Button
Recording Start/Stop Button
Stop (8) Button
5 Press E-MAIL to engage the E-Mail Clip Record-
Standby mode.
● “E-CLIP” appears.
6 Press the Recording Start/Stop Button to start
recording.
7 Press the Recording Start/Stop Button to stop
recording.
● “COMPLETED” is displayed, then the
camcorder re-enters the E-Mail Clip Record-
Standby mode.
8 Press E-MAIL to end E-Mail Clip Recording. The
normal screen reappears.
To view video clips stored in a memory card…
VIDEO/MEMORY Switch
E-MAIL Button
Refer to “Playback Of Video Clips” (੬ pg. 25).
To delete unwanted video clips stored in a memory
card…
Refer to “Deleting Files” (੬ pg. 28).
Play/Pause Button (4/9)
1
1
6
60
E-
E-
E-
CLIP
CLIP
CLIP
0h
h
25m
m
Remaining time
00 : 00
STANDBY
Approximate recording time
SD
Image Size
Memory
Card
240 x 176
160 x 120
Shooting starts when the
Recording Start/Stop
Button is pressed.
8 MB**
8 MB*
2 min.
2 min.
5 min.
6 min.
7 min.
15 min.
1
1
6
6
0
0
0hh1: 100mm
00 : 15
REC
16 MB*
*
Optional
** Provided (9 title images pre-stored)
Shooting stops when the
Recording Start/Stop
Button is pressed again.
NOTE:
0h00mm
h
1
1
6
6
0
0
It is not possible to adjust the speaker and
headphone volume during E-Mail Clip Recording
mode.
00 : 00
COMPLETED
To make video clips from recorded video
footage
Recording is complete.
1 Load a cassette. (੬ pg. 15)
2 Load a memory card. (੬ pg. 16)
3 Set the VIDEO/MEMORY Switch to “VIDEO”.
4 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
5 Set “E-CLIP REC” to the desired image size.
(੬ pg. 31, 38)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
51
6 Press 4/9 to start video playback.
Title Impose
A selection of titles/frames stored in the provided
memory card can be superimposed.
7 Press E-MAIL to engage the E-Mail Clip Record-
Standby mode.
● “E-CLIP” appears.
● To cancel E-Mail Clip Recording, press E-MAIL
MENU Wheel
TITLE Button
8 At the point you want to start dubbing, press the
Recording Start/Stop Button to start E-Mail Clip
Recording.
9 Press the Recording Start/Stop Button to stop
E-Mail Clip Recording.
● “COMPLETED” is displayed, then the
camcorder re-enters the E-Mail Clip Record-
Standby mode.
10Press E-MAIL to end E-Mail Clip Recording. The
normal screen reappears.
To view video clips stored in a memory card…
Refer to “Playback Of Video Clips” (੬ pg. 25).
INDEX Button
To delete unwanted video clips stored in a memory
card…
Title Selection
Refer to “Deleting Files” (੬ pg. 28).
1 Perform steps 1 to 6 in “Playback Of Title
Images” (੬ pg. 25).
NOTES:
● Playback operation cannot be performed during
E-Mail Clip Recording.
● If the end of the tape is reached during E-Mail Clip
Recording, that portion will be automatically
stored in the memory card.
● If the end of the tape is reached in step 7, the
E-Mail Clip Record-Standby mode will be
automatically cancelled.
● The video clip files stored with this camcorder are
compatible with MPEG4. Some MPEG4 files
stored with other devices cannot be played back
with this camcorder.
title, and press it.
4 Set “TITLE W/” to the desired mode.
(੬ pg. 31, 38)
Title Recording
5 Press TITLE during recording. The selected title/
frame is recorded.
● Press TITLE again to turn off the title/frame.
● The title image playback (TITLE) screen and the
title index screen (੬ pg. 25, 26) cannot be used
during E-Mail Clip Recording.
● Video noise may appear while viewing video clips
in the LCD monitor or viewfinder, however, this
noise is not present in the actual video clips stored
in the memory card.
● You can also view video clips on your PC by using
Windows® Media Player version 6.4 or later. Refer
to the instructions of PC and software.
NOTES:
● Title Impose can also be used for dubbing.
● You can delete unwanted titles/frames (“Deleting
Files” (੬ pg. 28)) or protect important ones from
accidental erasure (“Protecting Files” (੬ pg. 27)).
● A title/frame created on a PC can be transferred to
a memory card using the provided software.
Transferred titles/frames are displayed from title
index number 12. They can be used together with
the titles/frames in the provided memory card. For
details on creating/transferring titles/frames, refer
to the software instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
EN
DUBBING
4 Turn on the VCR’s power.
Dubbing To Or From A VCR
5 Insert the source cassette in the camcorder.
6 Insert the recording cassette in the VCR.
7 Engage the VCR’s AUX and Record-Pause modes.
8 Press 4/9 on the camcorder to start playback of
Connector
Cover***
the source tape.
9 At the point you want to start dubbing, engage
the VCR’s Record mode.
Connector
To S
Cover***
To AV
10 To pause dubbing, engage the VCR’s Record-
Pause mode and press 4/9 on the camcorder.
Audio/Video
cable
11 Repeat steps 8 – 10 for additional editing. Stop
the VCR and camcorder.
S-Video cable
(provided)
(optional)
NOTES:
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 11)
● As the camcorder starts to play your footage, it will
appear on your TV. This will confirm the
connections and the AUX channel for dubbing
purposes.
1
2
3
4
● Before you start dubbing, make sure that the
they do, they are being recorded onto the new
tape.
Cable Adapter*
“Y/C”/“CVBS” Video
Out Select Switch
To choose whether or not the following displays
appear on the connected TV...
• Date/time
TV
VCR
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
(੬ pg. 31, 41) Or, press DISPLAY on the remote
control to turn on/off the date indication.
• Time code
Set “TIME CODE” to “OFF” or “ON”.
(੬ pg. 31, 41)
A White to AUDIO L IN or OUT
B Red to AUDIO R IN or OUT
C Yellow to VIDEO IN or OUT
D To S-VIDEO IN or OUT**
*
If your VCR has a SCART connector, use the
provided cable adapter.
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
** Connect when your TV/VCR has an S-VIDEO
IN/OUT connector. In this case, it is not
necessary to connect the yellow video cable.
*** When connecting the cable, open the cover.
To use this camcorder as a recorder...
1) Perform steps 1 to 3 in the left column.
2) Set “S/AV INPUT” to “ON”. (੬ pg. 31, 40)
3) Set “REC MODE” to “SP” or “LP”. (੬ pg. 31, 34)
4) Insert the recording cassette in this camcorder.
5) Press the Recording Start/Stop Button to engage
NOTE:
Set the video out select switch of the cable adapter
as required:
Y/C: When connecting to a TV or VCR which accepts
Y/C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which does
not accept Y/C signals and uses an audio/video cable.
the Record-Pause mode. The “
appears on the screen.
” indication
A/V.IN
6) Press the Recording Start/Stop Button to start
recording. The indication rotates.
7) Press the Recording Start/Stop Button again to
stop recording. The indication stops rotating.
To use this camcorder as a player...
1 Following the illustrations, connect the
camcorder and the VCR. Also refer to page 22.
NOTES:
● After dubbing, set “S/AV INPUT” back to “OFF”.
● Analogue signals can be converted to digital
signals with this procedure.
2 Set the camcorder’s VIDEO/MEMORY Switch to
“VIDEO”.
3 Set the camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on
the switch.
● It is also possible to dub from another camcorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
53
1 Make sure all units are turned off.
Dubbing To A Video Unit Equipped
With A DV IN Connector
(Digital Dubbing)
2 Connect this camcorder to a video unit equipped
with a DV input connector using a DV cable as
shown in the illustration.
3 Set this camcorder’s VIDEO/MEMORY Switch to
“VIDEO”.
It is also possible to copy recorded scenes from the
camcorder onto another video unit equipped with a
DV connector. Since a digital signal is sent, there is
little if any image or sound deterioration.
4 Set this camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on
the switch.
5 Turn on the video unit’s power.
6 Insert the source cassette in this camcorder.
7 Insert the recording cassette in the video unit.
the source cassette.
9 At the point you want to start dubbing, engage
the video unit’s Record mode.
10 To pause dubbing, engage the video unit’s
Record-Pause mode and press 4/9 on this
camcorder.
To DV IN/OUT
11 Repeat steps 8 – 10 for additional editing. Stop
the video unit and camcorder.
NOTES:
Charger as the power supply instead of the
DV cable
Core filter
(optional)
● If the remote control is used when both the player
and recorder are JVC video units, both units will
perform the same operation. To prevent this from
happening, press the buttons on both units.
● If a blank portion or disturbed image is played
back on the player during dubbing, the dubbing
may stop so that an unusual image is not dubbed.
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 9. If
this occurs, turn off the power and make
connections again.
To DV IN
● If “Title Impose” (੬ pg. 51), “Playback Zoom”
(੬ pg. 57) or “Playback Special Effects”
(੬ pg. 58) is attempted or SNAPSHOT is pressed
during playback, only the original playback image
recorded on the tape is output from the DV IN/
OUT connector.
Video unit equipped with DV connector
● When using a DV cable, be sure to use the
optional JVC VC-VDV204U DV cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
EN
DUBBING (cont.)
1 Make sure all units are turned off.
Dubbing From A Video Unit
Equipped With A DV OUT
Connector (Digital Dubbing)
2 Connect this camcorder to a video unit equipped
with a DV output connector using a DV cable as
shown in the illustration.
3 Set this camcorder’s VIDEO/MEMORY Switch to
“VIDEO”.
It is also possible to copy recorded scenes from
another video unit equipped with a DV connector
onto the camcorder. Since a digital signal is sent,
there is little if any image or sound deterioration.
4 Set this camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on
the switch.
5 Set “REC MODE” to “SP” or “LP”. (੬ pg. 31, 34)
6 Turn on the video unit’s power.
7 Insert the source cassette in the video unit.
8 Insert the recording cassette in this camcorder.
9 Press the Recording Start/Stop Button to engage
the Record-Pause mode.
● The “
” indication appears on the screen.
DV. IN
10 Press the Recording Start/Stop Button to start
recording.
● The
indication rotates.
To DV IN/OUT
11 Press the Recording Start/Stop Button again to
engage the Record-Pause mode.
● The
indication stops rotating.
12 Repeat steps 10 – 11 for additional editing.
Stop the video unit and camcorder.
Core filter
DV cable (optional)
NOTES:
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 11)
To DV OUT
● If no image is displayed on the LCD monitor, set
“S/AV INPUT” to “OFF”. (੬ pg. 31, 40)
● If the remote control is used when both the player
and recorder are JVC video units, both units will
perform the same operation. To prevent this from
happening, press the buttons on both units.
● If a blank portion or disturbed image is played
back on the player during dubbing, the dubbing
may stop so that an unusual image is not dubbed.
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 9. If
this occurs, turn off the power and make
connections again.
Video unit equipped with
DV connector
● Digital Dubbing is performed in the sound mode
recorded on the original tape, regardless of the
current “SOUND MODE” setting. (੬ pg. 34)
● When using a DV cable, be sure to use the
optional JVC VC-VDV204U DV cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
55
1 Load a cassette. (੬ pg. 15)
Dubbing Still Images Recorded On
A Tape To A Memory Card
Still images can be dubbed from a tape to a memory
card.
2 Load a memory card. (੬ pg. 16)
3 Set the VIDEO/MEMORY Switch to “VIDEO”.
4 Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
5 Set “
COPY” to “ON”. (੬ pg. 31, 40)
MENU Wheel
6 Press 4/9 to start playback.
SNAPSHOT Button
7 At the point you want to dub, press 4/9 again to
engage Still Playback.
8 To dub the image, press SNAPSHOT.
● The ”
dubbing.
” indication appears during
● The selected image is stored in the memory
card.
NOTES:
● If SNAPSHOT is pressed in step 8 when a memory
card is not loaded, the message “COPYING
FAILED” is displayed.
● If an image recorded on the tape using “WIDE
MODE” (੬ pg. 36) is dubbed to a memory card,
the WIDE mode identifying signal is not dubbed
with it.
Power Switch
Lock Button
VIDEO/MEMORY
Play/Pause Button
Switch
(4/9)
● To use Playback Special effects with a video image
you wish to dub, perform up to step 8 using the
remote control (provided). (੬ pg. 58)
● Images are dubbed in 640 x 480 pixels.
Download from Www.Somanuals.com. All Manuals Search And Download.
56
EN
USING THE REMOTE CONTROL UNIT
The Full-Function Remote Control Unit can operate
this camcorder from a distance as well as the basic
operations (Playback, Stop, Pause, Fast-Forward and
Rewind) of your VCR. It also makes additional
playback functions possible. (੬ pg. 57)
A Infrared beam transmitting window
Transmits the beam signal.
The following buttons are available only when the
camcorder’s Power Switch set to “PLAY”.
B DISPLAY Button ................... (੬ pg. 22, 52, 61)
C SHIFT Button .............................. (੬ pg. 57, 60)
D SLOW Rewind/Forward Buttons ....... (੬ pg. 57)
Left/Right Buttons ............................ (੬ pg. 57)
E REW Button
Installing The Batteries
The remote control uses two “AAA (R03)” size
batteries. Refer to “General Battery Precautions”
(੬ pg. 74).
•Rewind/Reverse Shuttle Search
on a tape..........................................(੬ pg. 21)
•Displays previous file
1 Remove the battery compartment cover while
pushing up the tab as illustrated.
in a memory card.............................(੬ pg. 24)
F FADE/WIPE Button ........................... (੬ pg. 62)
G EFFECT ON/OFF Button ................... (੬ pg. 58)
H EFFECT Button .................................. (੬ pg. 58)
I PAUSE IN Connector ........................ (੬ pg. 61)
J MBR SET Button ............................... (੬ pg. 60)
K Up Button ........................................ (੬ pg. 57)
INSERT Button................................... (੬ pg. 59)
L Down Button .................................... (੬ pg. 57)
A. DUB Button.................................. (੬ pg. 58)
M PLAY Button
2 Insert two “AAA (R03)” size batteries in the
correct direction.
3 Re-attach the battery compartment cover.
1
3
Tab
+
2
–
–
+
•Starts Playback of a tape ..................(੬ pg. 20)
•Starts Auto Playback of images
in a memory card ............................(੬ pg. 24)
N FF Button
Insert the minus (–) end first.
•Forward/Forward Shuttle Search
on a tape .........................................(੬ pg. 21)
•Displays next file
Beam Effective Area (indoor use)
When using the remote
control, be sure to point it at
the remote sensor. The
transmitted beam’s
in a memory card ............................(੬ pg. 24)
O STOP Button
•Stops the tape ..................................(੬ pg. 20)
•Stops Auto Playback ........................(੬ pg. 24)
P PAUSE Button
Pauses the tape ..................................(੬ pg. 57)
Q R.A.EDIT Buttons ..................... (੬ pg. 60 – 64)
approximate effective
distance for indoor use is
5 m.
Remote sensor
NOTE:
The following buttons are available when the
camcorder’s Power Switch set to “A” or “M”.
a Zoom (T/W) Buttons
The transmitted beam may not be effective or may
cause incorrect operation when the remote sensor is
directly exposed to sunlight or powerful lighting.
Zoom in/out .................................(੬ pg. 18, 57)
(Also available with the Power Switch set to
“PLAY”)
Buttons And Functions
b START/STOP Button
Functions the same as the Recording Start/Stop
Button on the camcorder.
c SNAPSHOT Button
Functions the same as SNAPSHOT on the
camcorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
.
EN
57
Playback Zoom
Magnifies the recorded image up to 30X at any time
during video playback and D.S.C. playback.
1) Press PLAY (U) to start video
playback. Or perform normal
playback of images.
Zoom Buttons
SHIFT
Left or SLOW
Rewind Button
Up Button
Down Button
PLAY
PAUSE
STOP
Right or SLOW
Forward Button
2) At the point you want to zoom
in, press the Zoom Button (T).
● To zoom out, press the Zoom
Button (W).
Slow-Motion Playback
Allows slow-speed search in either direction during
video playback.
3) You can move the image on the
screen around to find a particular
portion of the picture. While
holding down SHIFT, press L
(Left), F (Right), U (Up) and E
(Down).
● To end zoom, press and hold W until
magnification returns to normal. Or, press
STOP (8) and then press PLAY (U) during video
playback.
During normal video playback, press SLOW (YI or
IU) more than approx. 2 seconds.
● After approx. 5 minutes (approx. 20 seconds with
an 80-minute cassete) in Slow Rewind or approx.
5 minutes in Slow Forward, normal playback
resumes.
● To pause Slow-Motion playback, press PAUSE (9).
● To stop Slow-Motion playback, press PLAY (U).
NOTES:
NOTES:
● Zoom can also be used during slow-motion and
still playback.
● You can also engage Slow-Motion Playback from
Still Playback by pressing SLOW (YI or IU) more
than approx. 2 seconds.
● Due to digital image processing, the quality of the
image may suffer.
● During Slow-Motion Playback, due to digital
image processing, the picture may take on a
mosaic effect.
● After SLOW (YI or IU) is pressed and held, the still
image may be displayed for a few seconds,
followed by a blue screen for a few seconds. This
is not a malfunction.
● There may be a small margin between the slow-
motion playback start point you chose and the
actual start point for Slow-Motion Playback.
● During Slow-Motion Playback, there will be
disturbances in video and the picture may seem
unstable, especially with steady images. This is not
a malfunction.
Frame-By-Frame Playback
Allows frame-by-frame search during video
playback.
During normal or still playback, press SLOW (IU)
repeatedly for forward or SLOW (YI) repeatedly for
reverse. Each time SLOW (YI or IU) is pressed, the
frame is played back.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
58
EN
USING THE REMOTE CONTROL UNIT (cont.)
Playback Special Effects
Allows you to add creative effects to the video
playback image.
The effects that can be used during playback are
Audio Dubbing
The audio track can be customised only when
recorded in the 12-bit and SP modes. (੬ pg. 34)
CLASSIC FILM, MONOTONE, SEPIA and STROBE.
The effects work the same in playback as they did in
recording. (੬ pg. 33)
Headphone Connector
Stereo Microphone
CLASSIC FILM: Gives recorded scenes a
strobe effect.
MONOTONE: Like classic black and white
films, your footage is shot in B/W. Used together
with the Cinema mode, it enhances the “classic
film” effect.
SEPIA: Recorded scenes have a brownish tint
like old photos. Combine this with the Cinema
mode for a classic look.
STROBE: Your recording looks like a series of
consecutive snapshots.
Speaker
1) To start playback, press PLAY (U).
2) Press EFFECT. The PLAYBACK EFFECT Select
Menu appears.
3) Press EFFECT repeatedly to move the highlight
bar to the desired effect.
● The selected function is activated and after
2 seconds the menu disappears.
A.DUB
PLAY
PAUSE
STOP
● To deactivate the selected effect, press EFFECT
ON/OFF. To reactivate the selected effect press
EFFECT ON/OFF again.
1 Play back the tape to locate the point where
editing will start, then press PAUSE (9).
● To change the selected effect, repeat from
step 2 above.
2 While holding A. DUB (D) on the remote
control, press PAUSE (9). The “9D” and “MIC”
indicators appear.
3 Press PLAY (U), then begin “narrating”. Speak
into the microphone.
● To pause dubbing, press PAUSE (9).
4 To end Audio Dubbing, press PAUSE (9), then
STOP (8).
To hear the sound during Audio Dubbing...
Connect optional headphones to the headphone
connector or use the AV connector, and set the
“12bit MODE” to the desired mode;
•“SOUND 1” for the playback sound.
•“SOUND 2” for the dubbed sound.
•“MIX” for the playback and dubbed sound.
To hear the dubbed sound during playback…
Set “12bit MODE” to “SOUND 2” or “MIX”.
(੬ pg. 31, 40)
NOTES:
● When editing onto a tape that was recorded at
12-bit, the old and new soundtracks are recorded
separately.
● If you dub onto a blank space on the tape, the
sound may be disrupted. Make sure you only edit
recorded areas.
● If feedback or howling occurs during TV playback,
move the camcorder’s microphone away from the
TV, or turn down the TV’s volume.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
59
● If you change from 12-bit to 16-bit in mid-
recording and then use the tape for Audio
Dubbing, it is not effective from the point where
16-bit recording began.
NOTES:
used to spice up the scenes being edited during
Insert Editing.
● During Audio Dubbing, when the tape moves to
scenes recorded in the LP mode, scenes recorded
in 16-bit audio or a blank portion, Audio Dubbing
stops.
● During Insert Editing, the date and time
information changes.
● If you perform Insert Editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
● During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Edting stops. (੬ pg. 84)
● If a memory card is loaded and “NAVIGATION” is
set to other than “MANUAL”, a NAVIGATION
thumbnail image is stored in the memory card.
(੬ pg. 48)
● To perform Audio Dubbing while watching on the
television, make connections. (੬ pg. 22)
● To perform Audio Dubbing with a video unit
connected to the camcorder’s AV connector, first
set “S/AV INPUT” to “ON” in VIDEO Menu.
(੬ pg. 31, 40)
The “AUX” indication appears instead of “MIC”.
Insert Editing
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
START/STOP
INSERT
REW
PLAY
STOP
NOTES:
● Before performing the following steps, make sure
that “TIME CODE” is set to “ON”. (੬ pg. 31, 41)
● Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
● To perform Insert Editing while watching in the
television, make connections. (੬ pg. 22)
1 Play back the tape, locate the Edit-Out point and
press PAUSE (9). Confirm the time code at this
point. (੬ pg. 41)
2 Press REW (3) until the Edit-In point is located,
then press PAUSE (9).
3 Press and hold INSERT (I) on the remote
control, then press PAUSE (9). The “9I”
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
4 Press START/STOP to begin editing.
● Confirm the insert at the time code you
checked in step 1.
● To pause editing, press START/STOP. Press it
again to resume editing.
5 To end Insert Editing, press START/STOP, then
STOP (8).
Download from Www.Somanuals.com. All Manuals Search And Download.
60
EN
USING THE REMOTE CONTROL UNIT (cont.)
VCR CODE LIST
Random Assemble Editing
[R.A.Edit]
Create edited videos easily using your camcorder as
the source player. You can select up to 8 “cuts” for
automatic editing, in any order you like. R.A.Edit is
more easily performed when the MBR (Multi-Brand
Remote) is set to operate with your brand of VCR
(see “VCR CODE LIST”), but can also be performed
by operating the VCR manually.
VCR BRAND
NAME
CODE
VCR BRAND
NAME
CODE
AKAI
F
F
G
B
D
G
PHILIPS
A
I
A
I
I
I
A
C
G
I
E
A
D
A
F
B
C
B
BLAUPUNKT
DAEWOO
A
A
C
H
FERGUSON
I
I
C
G
H
B
Before operation, make sure the batteries are
installed in the remote control. (੬ pg. 56)
SAMSUNG
SANYO
I
D
GRUNDIG
HITACHI
A
C
D
D
C
C
F
E
SHIFT
MBR SET
F
F
F
C
SELECO, REX
SHARP
I
I
A
F
JVC
A
B
C
I
I
I
A
F
C
A
A
E
SONY
F
F
C
C
E
LG/GOLDSTAR
MITSUBISHI
A
A
F
F
G
H
I
A
Set Remote/VCR Code
NEC
C
C
G
H
THOMSON,
TELEFUNKEN,
SABA,
I
I
I
C
A
F
G
B
1 Turn off the power to the VCR and point the
remote towards the VCR’s infrared sensor. Then,
referring to the VCR CODE LIST, press and hold
MBR SET, and enter the brand code.
PANASONIC
A
A
A
I
A
C
G
A
D
H
NORDMENDE
TOSHIBA
F
F
I
A
The code is automatically set once you release
MBR SET, and the VCR’s power comes on.
2 Make sure the VCR’s power is on. Then, while
holding SHIFT, press the button on the remote
for the desired function. The functions the remote
can control are PLAY, STOP, PAUSE, FF, REW
and VCR REC STBY (you do not need to press
SHIFT for this one).
You are now ready to try Random Assemble
Editing.
IMPORTANT:
Although the MBR is compatible with JVC VCRs
and those of many other makers, it may not work
with yours or may offer limited functions.
NOTES:
● If the VCR’s power does not come on in step 1, try
another code from the VCR CODE LIST.
● Some brands of VCR do not come on
automatically. In this case, turn the power on
manually and try step 2.
● If the remote control is not able to control the
VCR, use the controls on the VCR.
● When the remote control’s batteries run out, the
VCR brand you have set will be erased. In that
case, replace the old battery with a new one to
reset the VCR brand.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
61
1 A A JVC VCR equipped with a Remote PAUSE
Make Connections
Also refer to page 22.
connector…
…Connect the editing cable to the Remote
PAUSE connector.
B A JVC VCR not equipped with a Remote
PAUSE connector but equipped with an
R.A.EDIT connector…
…Connect the editing cable to the R.A.EDIT
connector.
C A VCR other than above…
…Connect the editing cable to the remote
control’s PAUSE IN connector.
Connector
Cover***
Connector
Cover***
To EDIT
To S
To AV
2 Insert a recorded tape into the camcorder.
3 Set the VIDEO/MEMORY Switch to “VIDEO”.
Editing cable
(provided)
Audio/Video
cable
(provided)
down the Lock Button located on the switch.
S-Video cable
(optional)
5 Turn the VCR power on, insert a recordable tape
and engage the AUX mode.
NOTES:
1
2
3
4
indications do not appear on the TV monitor. If
they do, they will be recorded onto the new tape.
To choose whether or not the following displays
appear on the connected TV…
Cable Adapter*
“Y/C”/“CVBS”
Video Out Select
Switch
• Date/time
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
(੬ pg. 31, 41) Or, press DISPLAY on the remote
control to turn on/off the date indication.
• Time code
ABTo Remote
PAUSE or
R.A.EDIT
VCR
Set “TIME CODE” to “OFF” or “ON”.
(੬ pg. 31, 41)
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
TV”. (੬ pg. 31, 41)
CTo PAUSE IN
TV
● When editing on a VCR equipped with a DV input
connector, an optional DV cable can be
connected instead of an S-Video cable and audio/
video cable.
DISPLAY
A White to AUDIO L IN
B Red to AUDIO R IN
C Yellow to VIDEO IN
D To S-VIDEO IN**
*
If your VCR has a SCART connector, use the
provided cable adapter.
** Connect when your TV/VCR has an S-VIDEO IN
connector. In this case, it is not necessary to
connect the yellow video cable.
*** When connecting the cable, open the cover.
NOTE:
Set the video out select switch of the cable adapter
as required:
Y/C: When connecting to a TV or VCR which accepts
Y/C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which does
not accept Y/C signals and uses an audio/video cable.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Select Scenes
EN
USING THE REMOTE CONTROL UNIT (cont.)
NOTES:
● When choosing a scene, set Edit-In and Edit-Out
points so that there is a relatively large difference
between them.
● If the search time for an in-point exceeds
5 minutes, the recording deck’s Record-Standby
mode will be cancelled and editing will not take
place.
● If there are blank portions before or after the Edit-
In and Edit-Out points, a blue screen may be
included in the edited version.
● Since time codes register time only as accurately
as seconds, the time code total time may not
match the total program time exactly.
● Turning off the camcorder’s power erases all
registered Edit-In and Edit-Out points.
● If you select Sepia or Monotone mode from
Program AE with special effects, you cannot use
the Dissolve or Black & White Fader. In this case
the Dissolve or Black & White indicator begins
blinking. Once the next Edit-In point is registered,
the effect is turned off. To combine these effects,
use Sepia or Monotone during recording, then use
the Dissolve or Black & White Fader during
Random Assemble Editing.
PLAY
FADE/WIPE
EFFECT
EDIT IN/OUT
R.A.EDIT
ON/OFF
CANCEL
6 Press PLAY (U) and then press R.A.EDIT ON/OFF
on the remote control.
The Random Assemble
Editing Menu appears.
Selected parameter
I N
OUT
MODE
7 If using a Wipe/Fader at
the beginning of the
scene, press FADE/WIPE
on the remote control.
● Cycle through the
effects by pressing
1
2
3
4
5
6
7
8
– –
– – : – –
~
~
~
~
~
~
~
~
T I ME CODE
TOTAL
– –
00 : 00
:
– –
repeatedly, and stop
when the one you want is displayed.
● You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
● It is not possible to use Wipe/Fader effects and
Program AE with special effects during Random
Assemble Editing using a DV cable.
8 At the beginning of the scene, press EDIT IN/
OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
9 At the end of the scene, press EDIT IN/OUT. The
Edit-Out position appears in the Random
Assemble Editing Menu.
press FADE/WIPE.
● Cycle through the effects by pressing
repeatedly, and stop when the one you want is
displayed.
● If you select a Wipe/Fader effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
● You cannot use a Picture Wipe/Dissolve at the
end of the last scene.
● When you use Fader/Wipe effects, that time is
included in the total time (this does not apply
to Picture Wipe/Dissolve).
11 If using Playback Special Effects, press EFFECT.
(੬ pg. 58)
12 Repeat steps 8 through 11 to register
additional scenes.
● To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
● If you are not using Wipe/Fader or Program AE
with special effects, repeat steps 8 and 9 only.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
63
Picture Wipe And Dissolve Menu
(available only for Random Assemble Editing)
You can use not only the wipe/fader effects on
page 32 but also the picture wipe and dissolve
effects below.
Automatic Editing To VCR
DISSOLVE: The new scene gradually appears
as the old one gradually disappears.
PAUSE
WIPE – CORNER: The new scene wipes in
over the previous one from the upper right corner to
the lower left corner.
VCR REC STBY
WIPE – WINDOW: The next scene gradually
wipes in from the centre of the screen toward the
corners, covering the previous scene.
WIPE – SLIDE: The next scene gradually wipes
in over the previous one from right to left.
WIPE – DOOR: The previous scene wipes out
from the centre to the right and left, like a door
being pushed open to reveal the next scene.
WIPE – SCROLL: The new scene wipes in over
the last one from the bottom of the screen to the top.
13 Rewind the tape in the camcorder to the
beginning of the scene you want to edit and press
PAUSE (9).
14 Press VCR REC STBY (79), or manually
engage the VCR’s Record-Pause mode.
15 Press the Recording Start/Stop Button on the
camcorder. Editing proceeds as programmed,
right through to the end of the last registered
scene.
WIPE – SHUTTER: The new scene wipes in
over the previous one from the centre toward the top
and bottom of the screen.
● When dubbing is complete, the camcorder
enters the Pause mode, and the VCR enters its
Record-Pause mode.
● If you do not register an Edit-Out point, the
tape will be dubbed all the way to the end
automatically.
● If you operate the camcorder during automatic
editing, the VCR will enter its Record-Pause
mode and automatic editing will stop.
16 Engage the Stop modes for the camcorder and
the VCR.
press R.A.EDIT ON/OFF on the remote control.
NOTES:
● Pressing R.A.EDIT ON/OFF on the remote control
clears all settings registered during Random
Assemble Editing.
● When the editing cable is connected to the remote
control’s PAUSE IN connector during dubbing,
make sure the remote control is pointed at the
VCR’s sensor, and the path between the two is
unobstructed.
● Random Assemble Editing may not function
properly when using a tape including several
duplicated time codes. (੬ pg. 19)
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
64
EN
USING THE REMOTE CONTROL UNIT (cont.)
Adjustment Of VCR/Camcorder Timing
4 Press R.A.EDIT ON/OFF to make the Random
Assemble Editing menu disappear, then press the
MENU Wheel in. The Menu Screen appears.
For More Accurate Editing
5 Rotate the MENU Wheel to select “t”, and
press it. The VIDEO Menu appears.
6 Rotate the MENU Wheel to select “SYNCHRO”,
and press it. The value for “SYNCHRO” is
highlighted.
R.A.EDIT
ON/OFF
7 Based on the diagnostics performed, you can
now advance the VCR’s record timing by rotating
the MENU Wheel towards “+”. You can also
delay the VCR’s record timing by rotating the
MENU Wheel towards “–”.
Some VCRs make the transition from Record-Pause
to Record mode faster than others. Even if you begin
editing for the camcorder and the VCR at exactly the
same time, you may lose scenes you wanted, or find
that you have recorded scenes you did not want. For
a cleanly edited tape, confirm and adjust the timing
of the camcorder against your VCR.
The adjustment range is from –1.3 to +1.3
seconds, in 0.1-second increments.
Press the MENU Wheel in to finish the setting.
8 Rotate the MENU Wheel to select “BRETURN”,
and press it twice.
Diagnosing VCR/Camcorder Timing
Now perform Random Assemble Editing
beginning with step 6 on page 62.
1 Play back the tape in the camcorder, then point
the remote control at the camcorder’s remote
sensor and press R.A.EDIT ON/OFF.
NOTES:
● Before performing actual Random Assemble
Editing, do a few Random Assemble Editing trial
runs to check whether the value you have input is
appropriate or not, and make adjustments
accordingly.
Random Assemble Editing Menu appears.
Program 1
I N
OUT
MODE
Random Assemble
Editing Menu
1
2
3
4
5
6
7
8
– –
– – : – –
~
~
~
~
~
~
~
~
● Depending on the recorder, there may be
situations where the timing difference cannot be
fully corrected.
T I ME CODE
TOTAL
– –
:
– –
00 : 00
2 Perform Random Assemble Editing on Program 1
only. In order to check VCR and camcorder
timing, select the beginning of a scene transition
as your Edit-In point.
3 Play back the dubbed scene.
● If any images from the scene prior to the
transition you chose for your Edit-In point were
recorded, that means your VCR moves too
quickly from Record-Pause to Record mode.
● If the scene you tried to dub starts in progress,
the VCR is slow to start recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
65
SYSTEM CONNECTIONS
Connection To A Personal Computer
[A] Using USB cable
To USB connector
USB cable (provided)
PC
To USB
[B] Using DV cable
OR
To DV
connector
DV cable
(optional)
Core filter
Core filter
PC with DV
connector
To DV IN/OUT
● When using a DV cable, be sure to use the
[A] Using USB cable
It is possible to do the following things:
● Transfer still images stored on a memory card to a
PC.
● Transfer still/moving images recorded on a tape to
a PC.
optional JVC VC-VDV206U or VC-VDV204U DV
cable depending on the type of DV connector (4
or 6 pins) on the PC.
● If the PC connected to the camcorder via the USB
cable is not powered, the camcorder does not
enter the USB mode.
● The date/time information cannot be captured into
the PC.
● Capture still/moving images in real-time.
● Use this camcorder as a WebCam. (੬ pg. 66)
● Refer to the instruction manuals of the PC and
Software.
● The still images can also be transferred to a PC
with a DV connector-equipped capture board.
● The system may not work properly depending on
the PC or capture board you are using.
[B] Using DV cable
It is also possible to transfer still/moving images to a
PC with a DV connector by using the provided
software, software equipped with the PC or
commercially available software.
“USB MODE” and/or “ACCESSING FILES”
appears on the LCD monitor while the PC is
accessing data in the camcorder or the camcorder
is transferring a file to the PC.
NEVER disconnect the USB cable while
“ACCESSING FILES” is displayed on the LCD
monitor since this can result in product damage.
NOTES:
● Refer to “SOFTWARE INSTALLATION AND USB
CONNECTION GUIDE” for the installation of the
bundled software and drivers.
● The software operation manual is provided as PDF
file on the CD-ROM.
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 11)
● Never connect the USB cable and the DV cable
simultaneously to the camcorder. Connect only
the cable you wish to use to the camcorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
66
EN
SYSTEM CONNECTIONS (cont.)
1 Make sure all necessary software (provided) are
Using The Camcorder As A
WebCam
installed in your PC and all units are turned off.
2 Connect the camcorder to your PC using the USB
cable.
3 Set the VIDEO/MEMORY Switch to “MEMORY”.
This camcorder can be used as a WebCam via USB
connection.
pressing down the Lock Button located on the
switch.
5 Turn on the PC.
● “
” appears on the screen.
● If the PC is not powered on, the camcorder
does not enter the Web Camera mode.
6 When finished, turn off the PC first, then the
camcorder. Disconnect the USB cable from the
camcorder and PC.
NOTES:
To USB
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 11)
● Use the provided software PIXELA ImageMixer to
capture video in real time.
USB cable
(provided)
● You can also use the camcorder for web
conference by using Microsoft Windows®
NetMeeting® and signing up for MSN Hotmail.
● In the Web Camera mode, the following buttons
cannot be operated: TITLE, E-MAIL, SNAPSHOT,
INDEX, NAVI, NAVI STORE, the Recording Start/
Stop Button.
Refer to the instruction manuals of the PC and
provided Software.
To USB connector
USB-equipped PC
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
67
DETAILS
ITEMS
NOTES
V Power (੬ pg. 10)
● Perform charging where the temperature is between 10°C and 35°C. 20°C to 25°C
is the ideal temperature range for charging. If the environment is too cold,
charging may be incomplete.
● Charging times are for a fully discharged battery pack.
● Charging time varies according to the ambient temperature and the status of the
battery pack.
● To avoid interference with reception, do not use the AC Power Adapter/Charger
near a radio.
● Since the AC Power Adapter/Charger processes electricity internally, it becomes
warm during use. Be sure to use it only in well-ventilated areas.
V VIDEO
RECORDING
(੬ pg. 17)
● When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may
be difficult to see. If this happens, use the viewfinder instead.
● The cassette holder cannot be opened unless a power supply is attached.
holder opens. Do not use force.
completely before closing the cassette holder cover.
● When the Recording Start/Stop button is pressed, it may take a few seconds before
actual recording starts. The “T” indicator starts rotating when the camcorder
actually starts recording.
● The time required to calculate and display the remaining tape length, and the
accuracy of the calculation, may vary according to the type of tape used.
● “TAPE END” appears when the tape reaches its end, and the power goes off
automatically if left in this condition for 5 minutes. “TAPE END” also appears
when a cassette at its end is loaded.
● During recording, sound is not heard from the speaker. To hear the sound, connect
optional headphones to the headphone connector. Adjust the sound volume by
rotating the MENU Wheel. (੬ pg. 20)
● During Interface Shooting, the “Tape Running” indicator and warning indications
(੬ pg. 84, 85) are the only ones that are shown; they appear reversed in the
display as they would when viewing a mirror, but are not reversed in the
recording.
● The tape remaining indicator does not appear during interface shooting. However,
when the remaining time reaches 2 minutes, the indicator appears showing the
remaining time:
(blinking)
(blinking)
(blinking)
Download from Www.Somanuals.com. All Manuals Search And Download.
68
EN
TROUBLESHOOTING
If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery
pack, AC Power Adapter/Charger, etc.) and wait a few minutes; and then re-connect it and proceed as usual
from the beginning.
Power
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
1. No power is supplied.
1. •The power is not connected 1. •Connect the AC Power
properly.
Adapter/Charger securely.
(੬ pg. 11)
•The battery is dead.
•The LCD monitor is not open
fully or the viewfinder is not
pulled out when recording.
•Replace the dead battery
with a fully charged one.
(੬ pg. 10, 11)
•Open the LCD monitor fully
or pull out the viewfinder.
Video and D.S.C. Recording
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
2. Recording cannot be
2. •The Power Switch is set to
“PLAY” or “OFF”.
2. •Set the Power Switch to “A”
or “M”. (੬ pg. 17, 23)
— For Video Recording —
•Set the tape’s erase
protection tab to “REC”.
(੬ pg. 15)
performed.
— For Video Recording —
•The tape’s erase protection
tab is set to “SAVE”.
•The VIDEO/MEMORY
Switch is set to “MEMORY”.
•“TAPE END” appears.
•The cassette holder cover is
open.
•Set the VIDEO/MEMORY
Switch to “VIDEO”.
•Replace with new cassette.
(੬ pg. 15)
— For D.S.C. Recording —
•The VIDEO/MEMORY
Switch is set to “VIDEO”.
•Close the cassette holder
cover.
— For D.S.C. Recording —
•Set the VIDEO/MEMORY
Switch to “MEMORY”.
3. When shooting a subject
illuminated by bright light,
vertical lines appear.
3. •This is a result of exceedingly 3.
high contrast, and is not a
malfunction.
—
—
4. When the screen is under
direct sunlight during shooting,
the screen becomes red or
black for an instant.
4. •This is not a malfunction.
4.
5. During recording, the date/
5. •“DATE/TIME” is set to “OFF”. 5. •Set “DATE/TIME” to “ON”.
(੬ pg. 31, 38)
time does not appear.
6. During recording, sound
6. •The optional headphones are 6. •Connect the optional
cannot be heard.
not connected to the
headphones to the
headphone connector.
(੬ pg. 81)
headphones connector.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
69
7. The LCD monitor or
7. •Certain Wipe/Fader effects,
certain modes of Program AE
with special effects, “DIS”
and other functions that
7. •Re-read the sections covering
Wipe/Fader effects, Program
AE with special effects and
“DIS”. (੬ pg. 31 – 33, 35)
viewfinder indications blink.
cannot be used together are
selected at the same time.
8. Digital Zoom does not work. 8. •10X optical zoom is selected. 8. •Set “ZOOM” to “40X” or
•The VIDEO/MEMORY
Switch is set to “MEMORY”.
“300X”. (੬ pg. 34)
•Set the VIDEO/MEMORY
Switch to “VIDEO”.
Video and D.S.C. Playback
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
9. Play, Rewind and Fast-Forward 9. •The Power Switch is set to
9. •Set the Power Switch to
“PLAY”. (੬ pg. 20)
functions do not work.
“A” or “M”.
•VIDEO/MEMORY Switch is
set to “MEMORY”.
•Set the VIDEO/MEMORY
Switch to “VIDEO”.
10. The tape is moving, but there is 10. •Your TV has AV input
10. •Set the TV to the mode or
channel appropriate for
video playback. (੬ pg. 22)
•Close the cassette holder
cover. (੬ pg. 15)
no picture.
terminals, but is not set to its
VIDEO mode.
•The cassette holder cover is
open.
11. Blocks of noise appear during 11.
playback, or there is no
11. •Clean the video heads with
an optional cleaning
cassette.
—
playback picture and the
screen becomes blue.
12. A memory card cannot be
12. •The Power Switch is set to
“A” or “M”.
12. •Set the Power Switch to
“PLAY”. (੬ pg. 24)
played back.
•The VIDEO/MEMORY
Switch is set to “VIDEO”.
•Set the VIDEO/MEMORY
Switch to “MEMORY”.
Download from Www.Somanuals.com. All Manuals Search And Download.
70
EN
TROUBLESHOOTING (cont.)
Advanced features
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
13. The focus does not adjust
13. •Focus is set to the Manual
13. •Set Focus to the Auto mode.
(੬ pg. 45)
automatically.
mode.
•The recording was done in a
dark place, or the contrast
was low.
•Clean the lens and check the
focus again. (੬ pg. 77)
•The lens is dirty or covered
with condensation.
14. In the 5-Second mode,
recording ends before
“Anim.” in MANUAL Menu.
Menu. (੬ pg. 31, 36)
5 seconds have elapsed.
15. Snapshot mode cannot be
15. •The Squeeze mode
15. •Disengage the Squeeze
(SQUEEZE) mode.
used.
(SQUEEZE) is selected.
(੬ pg. 31, 36)
16. The colour of Snapshot looks 16. •The light source or the
16. •Find a white subject and
compose your shot so that it
also appears in the frame.
(੬ pg. 23, 42)
strange.
subject does not include
white. Or there are various
different light sources behind
the subject.
•The Sepia (SEPIA) or
Monotone (MONOTONE)
mode is activated.
•Disengage the Sepia (SEPIA)
and Monotone
(MONOTONE). (੬ pg. 31,
33)
17. The image taken using
17. •Shooting was performed
17. •Press BACK LIGHT.
(੬ pg. 47)
Snapshot is too dark.
under backlit conditions.
18. The image taken using
18. •The subject is too bright.
18. •Set “r” to “SPOTLIGHT”.
(੬ pg. 33)
Snapshot is too bright.
19. White Balance cannot be
19. •The Sepia (SEPIA) or
Monotone (MONOTONE)
mode is activated.
19. •Disengage the Sepia (SEPIA)
or Monotone (MONOTONE)
mode before setting White
Balance. (੬ pg. 33)
activated.
20. Wipe/Fader effects do not
20. •The Power Switch is set to
“A”.
20. •Set the Power Switch to “M”.
(੬ pg. 13)
work.
21. The Black & White Fader does 21. •The Sepia (SEPIA) or
21. •Disengage the Sepia (SEPIA)
and Monotone
not work.
Monotone (MONOTONE)
mode is activated.
(MONOTONE).
(੬ pg. 31, 33)
22. Program AE with special
22. •The Power Switch is set to
“A”.
22. •Set the Power Switch to “M”.
(੬ pg. 13)
effects does not work.
23. The image looks like the
23. •When shooting in the dark, 23. •If you want the lighting to
shutter speed is too slow.
the unit becomes highly
sensitive to light when
“GAIN UP” is set to
“AUTO”.
look more natural, set “GAIN
UP” to “AGC” or “OFF”.
(੬ pg. 31, 35)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
71
24. Although Snapshot is
attempted, flash does not take
place.
24. •The subject is too bright with 24. •Set “B-IN FLASH” to “ON”
the flash set to “AUTO” or
“AUTO C”.
in MANUAL Menu.
(੬ pg. 31, 37)
•It can take up to 10 seconds
to charge the flash.
•If blinks, the flash is being
charged.
•The camcorder is in the
Record mode.
•Set the camcorder in the
Record-Standby mode.
(੬ pg. 42, 43)
25. Although a Snapshot is taken 25. •The subject does not look
straight toward the flash,
especially the first flash. If
the subject does not see the
first flash, it will be difficult
for Red-Eye Reduction to
take place. (੬ pg. 43)
with the flash, Red-Eye
straight toward the flash.
•The subject does not look at
the first flash, which is an
important part of Red-Eye
Reduction.
Reduction does not take place.
•The camcorder is too far
from the subject.
•In MANUAL Menu, “B-IN
FLASH” is not set to
“AUTO C”.
•The flash is effective for
subjects at a distance of
approx. 0.7 m to 2 m from
the camcorder. (੬ pg. 43)
•Set “B-IN FLASH” to
“AUTO C” to display the
Red-Eye Reduction indicator.
(੬ pg. 31, 37)
Other problems
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
26. The CHARGE indicator on the 26. •The temperature of the
26. •To protect the battery, it is
recommended to charge it in
places with a temperature of
10°C to 35°C. (੬ pg. 74)
AC Power Adapter/Charger
does not light.
battery is extremely high/low.
•Charging is difficult in places
subject to extremely high/
low temperatures.
27. “SET DATE/TIME!” appears.
28. There is no picture.
27. •The built-in clock’s
rechargeable lithium battery
is discharged.
27. •Connect the camcorder to an
AC outlet using the AC Power
Adapter/Charger for over 24
hours to charge the clock’s
lithium battery. (੬ pg. 14)
•The previously set date/time
is erased.
28. •The camcorder is not getting 28. •Turn the camcorder’s power
power, or some other
malfunction exists.
off and on again. (੬ pg. 13)
29. Some functions are not
available using the MENU
Wheel.
29. •The Power Switch is set to
“A”.
29. •Set the Power Switch to “M”.
(੬ pg. 13)
30. Files stored in the memory
30. •Files stored in the memory
30. •Remove protection from the
files stored in the memory
card and delete them.
card cannot be deleted.
card are protected.
(੬ pg. 27 –28)
31. When the image is printed
from the printer, a black bar
appears at the bottom of the
screen.
31. •This is not a malfunction.
31. •By recording with “DIS”
activated (੬ pg. 31, 35) this
can be avoided.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
72
EN
TROUBLESHOOTING (cont.)
32. When the camcorder is
connected via the DV
connector, the camcorder does
not operate.
32. •The DV cable was plugged/ 32. •Turn the camcorder’s power
unplugged with power
turned on.
off and on again, then
operate it.
33. The rear of the LCD monitor is 33. •The light used to illuminate 33. •Close the LCD monitor to
hot.
the LCD monitor causes it to
become hot.
turn it off or set the Power
Switch to “OFF”, and let the
unit cool down.
34. Images on the LCD monitor
34. •In places subject to low
temperature, images become
dark due to the
34. •Adjust the brightness and
angle of the LCD monitor.
(੬ pg. 12, 13)
appear dark or whitish.
characteristics of the LCD
monitor. When this happens,
the displayed colours differ
from those that are actually
recorded. This is not a defect
of the camcorder.
•When the LCD monitor’s
fluorescent light reaches the
end of its service life, images
on the LCD monitor become
dark. Consult your nearest
JVC dealer.
35. Coloured bright spots appear 35. •The LCD monitor and the
35.
all over the LCD monitor or the
viewfinder.
viewfinder are made with
high-precision technology.
However, black spots or
bright spots of light (red,
green or blue) may appear
constantly on the LCD
monitor or the viewfinder.
These spots are not recorded
on the tape. This is not due to
any defect of the unit.
—
(Effective dots: more than
99.99 %)
36. The indicators and the image 36. •This may occur when the
36.
colour on the LCD monitor are
not clear.
surface or the edge of the
LCD monitor is pressed.
—
37. The cassette will not load
37. •The battery’s charge is low.
37. •Install a fully charged battery.
(੬ pg. 10, 11)
properly.
38. The memory card cannot be
38.
38. •Push in the memory card a
few more times. (੬ pg. 16)
—
removed from the camcorder.
39. Picture does not appear on the 39. •The viewfinder is pulled out 39. •Push the viewfinder back in
LCD monitor.
and “PRIORITY” is set to
“FINDER”.
or set “PRIORITY” to “LCD”.
(੬ pg. 12, 31, 38)
•The LCD monitor’s brightness
setting is too dark.
•Adjust the brightness of the
LCD monitor. (੬ pg. 13)
•If the monitor is tilted
upward 180 degrees, open
the monitor fully. (੬ pg. 12)
40. Images on the LCD monitor
40. •The speaker volume is too
40. •Turn the speaker volume
down. (੬ pg. 20)
are jittery.
great.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
73
41. The LCD monitor, the
41.
cloth. Wiping strongly can
cause damage. (੬ pg. 77) To
clean the viewfinder, please
consult your nearest JVC
dealer.
viewfinder and the lens have
become dirty (ex. fingerprints).
—
42. Time code does not appear.
42. •“TIME CODE” is set to
42. •Set “TIME CODE” to “ON”.
(੬ pg. 31, 38, 41)
“OFF”.
43. An error indication (E01, E02 43. •A malfunction of some kind 43. •੬ pg. 85.
or E06) appears.
has occurred. In this case the
camcorder’s functions
become unusable.
44. An error indication (E03 or
44. •A malfunction of some kind 44. •੬ pg. 85.
has occurred. In this case the
camcorder’s functions
E04) appears.
become unusable.
45. The remote control does not
45. •“REMOTE” is set to “OFF”.
•The remote control does not
point at the remote sensor.
•The remote control batteries
are exhausted.
45. •Set “REMOTE” to “ON”.
work.
(੬ pg. 31, 37)
•Point at the remote sensor.
(੬ pg. 56)
•Replace the batteries with
fresh ones. (੬ pg. 56)
Download from Www.Somanuals.com. All Manuals Search And Download.
74
EN
CAUTIONS
NOTES:
General Battery Precautions
If the remote control is not functioning even if it is
being operated correctly, the batteries are
exhausted. Replace them with fresh ones.
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging........10°C to 35°C
Operation......0°C to 40°C
Use only the following batteries: AAA (R03) size x 2
Storage ..........–20°C to 50°C
● Recharging time is based on room temperature of
20°C.
● The lower the temperature, the longer recharging
takes.
Please make note of the following rules for battery
use. When misused, the batteries can leak or
explode.
1. When replacing batteries, refer to page 56.
2. Do not use any different size of batteries from
those specified.
3. Be sure to install batteries in the correct
direction.
4. Do not use rechargeable batteries.
5. Do not expose the batteries to excessive heat as
they can leak or explode.
6. Do not dispose of the batteries in a fire.
7. Remove the batteries from the unit if it is to be
stored for an extended period to avoid battery
leakage which can cause malfunctions.
8. Do not recharge the provided batteries.
Cassettes
To properly use and store your cassettes, be sure to
read the following cautions:
1. During use…
... make sure the cassette bears the Mini DV
mark.
... be aware that recording onto prerecorded
tapes automatically erases the previously
recorded video and audio signals.
... make sure the cassette is positioned properly
when inserting.
... do not load and unload the cassette
repeatedly without allowing the tape to run at
all. This slackens the tape and can result in
damage.
Battery Packs
The supplied battery pack
is a lithium-ion battery.
Before using the supplied
battery pack or an
... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
2. Store cassettes…
optional battery pack, be
sure to read the following
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
... vertically, in their original cases.
Terminals
cautions:
1. To avoid hazards…
... do not burn.
... do not short-circuit the terminals. When
transporting, make sure the provided battery
cap is attached to the battery. If the battery cap
is misplaced, carry the battery in a plastic bag.
... do not modify or disassemble.
... do not expose the battery to temperatures
exceeding 60°C, as this may cause the battery
to overheat, explode or catch fire.
... use only specified chargers.
2. To prevent damage and prolong service life…
... do not subject to unnecessary shock.
... charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type
battery — cooler temperatures impede
chemical reaction, while warmer
temperatures can prevent complete charging.
... store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
... fully charge and then fully discharge the
battery every 6 months when storing the
battery pack over a long period time.
... remove from charger or powered unit when
not in use, as some machines use current even
when switched off.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
75
... in places subject to soot or steam such as near
a cooking stove.
... in places subject to excessive shock or
vibration.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting
antennas, etc.).
... in places subject to extremely high (over
40°C) or extremely low (under 0°C)
temperatures.
Memory Cards
To properly use and store your memory cards, be
sure to read the following cautions:
1. During use…
... make sure the memory card bears the SD or
MultiMediaCard mark.
... make sure the memory card is positioned
properly when inserting.
2. While the memory card is being accessed
(during recording, playback, deletion,
initialisation, etc.)…
... never unload the memory card and never turn
off the camcorder.
3. Store memory cards…
3. DO NOT leave the unit…
... in places of over 50°C.
... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
4. To protect the unit, DO NOT…
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration
during transportation.
... keep the lens directed at extremely bright
objects for long periods.
... expose the lens and viewfinder’s lens to direct
sunlight.
LCD Monitor
1. To prevent damage to the LCD monitor,
DO NOT…
... push it strongly or apply any shocks.
... place the camcorder with the LCD monitor on
the bottom.
... carry it by holding the LCD monitor or the
viewfinder.
... swing it excessively when using the hand strap
or the grip.
2. To prolong service life…
... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD
monitor use.
... swing the soft camera case excessively when
the camcorder is inside it.
These are not malfunctions:
•While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
•If you leave power on for a long time, the
surface around the LCD monitor becomes hot.
Main Unit
1. For safety, DO NOT…
... open the camcorder’s chassis.
... disassemble or modify the unit.
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not
in use.
... allow inflammables, water or metallic objects
to enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
2. Avoid using the unit…
... in places subject to excessive humidity or
dust.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
76
EN
CAUTIONS (cont.)
5. Dirty heads can cause the following problems:
How To Handle A CD-ROM
•Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or back
surface. If the CD-ROM gets dirty, gently wipe it
with a soft cloth outward from the centre hole
using a circular motion.
•Do not use conventional disc cleaners or cleaning
spray.
•Do not bend the CD-ROM or touch its mirror
surface.
•No picture during playback.
•Blocks of noise appear during playback.
•During recording or playback, the Head Clog
Warning indicator “ ” appears.
•Recording cannot be performed properly.
In such cases, use an optional cleaning cassette.
Insert it and play back. If the cassette is used more
than once consecutively, damage to the video heads
may result. After the camcorder plays back for about
20 seconds, it stops automatically. Also refer to the
cleaning cassette’s instructions.
•Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
About moisture condensation...
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form on
the glass’ outer surface. This same phenomenon
occurs on the head drum of a camcorder when
it is moved from a cool place to a warm place,
after heating a cold room, under extremely
humid conditions or in a place directly
If, after using the cleaning cassette, the problems still
exist, consult your nearest JVC dealer.
Mechanical moving parts used to move the video
heads and video tape tend to become dirty and
worn out over time. In order to maintain a clear
picture at all times, periodic check-ups are
recommended after using the unit for about 1,000
hours. For periodic check-ups please consult your
nearest JVC dealer.
subjected to the cool air from an air conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
The camcorder is a microcomputer-controlled
device. External noise and interference (from a TV,
a radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Power Adapter/
Charger, etc.) and wait a few minutes and then re-
connect it and proceed as usual from the
beginning.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
77
USER MAINTENANCE
After Use
Cleaning The Camcorder
1 Turn off the camcorder.
1 To clean the exterior, wipe gently with a soft
cloth.
2 Slide and hold OPEN/EJECT in the direction of
the arrow, then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically. Remove the cassette.
Put the cloth in diluted mild soap and wring it
well to wipe off heavy dirt. Then wipe again with
a dry cloth.
2 Press PUSH OPEN and open the LCD monitor.
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
3 Press “PUSH HERE” to close the cassette holder.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
3 To clean the lens, blow it with a blower brush,
then wipe gently with lens cleaning paper.
4 Slide BATT.RELEASE 1 and remove the battery
pack 2 3.
NOTES:
● Avoid using strong cleaning agents such as
benzine or alcohol.
● Cleaning should be done only after the battery
pack has been removed or other power units have
been disconnected.
● Mould may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth
refer to the cautions of each product.
● To clean the viewfinder, please consult your
nearest JVC dealer.
Remove.
PUSH HERE
Cassette holder
Cassette
holder cover
OPEN/EJECT
Switch
BATT.RELEASE Switch
Download from Www.Somanuals.com. All Manuals Search And Download.
78
EN
SPECIFICATIONS
Camcorder
For General
Power supply
:
DC 6.3 V (Using AC Power Adapter/Charger)
DC 7.2 V (Using battery pack)
Power consumption
LCD monitor off, viewfinder on : Approx. 3.8 W
LCD monitor on, viewfinder off : Approx. 4.9 W
Dimensions (W x H x D)
:
74.5 mm x 91 mm x 198 mm
(with the LCD monitor closed and the viewfinder pushed back in)
Weight
:
Approx. 660 g
(without cassette, memory card and battery)
Approx. 740 g
(incl. cassette, memory card and battery)
Operating temperature
Operating humidity
Storage temperature
Pickup
:
:
:
:
:
:
:
:
:
0°C to 40°C
35% to 80%
–20°C to 50°C
1/4" CCD
Lens
F 1.2, f = 3.8 mm to 38 mm, 10:1 power zoom lens
ø52 mm
3.5" diagonally measured, LCD panel/TFT active matrix system
Electronic viewfinder with 0.24" colour LCD
Monaural
Filter diameter
LCD monitor
Viewfinder
Speaker
For Digital Video Camera
Format
Signal format
:
:
:
DV format (SD mode)
PAL standard
Video : Digital component recording
Audio : PCM digital recording, 32 kHz 4-channel (12-bit), 48 kHz
2-channel (16-bit)
Recording/Playback format
Cassette
Tape speed
:
:
Mini DV cassette
SP: 18.8 mm/s
LP: 12.5 mm/s
Maximum recording time
(using 80 min. cassette)
:
SP: 80 min.
LP: 120 min.
For Digital Still Camera
Storage media
Compression system
:
:
SD Memory Card/MultiMediaCard
Still image
: JPEG (compatible)
Moving image : MPEG4 (compatible)
File size
Still image
:
4 modes (1600 x 1200 pixels/1280 x 960 pixels/1024 x 768 pixels/
640 x 480 pixels)
Moving image
Picture quality
:
:
2 modes (240 x 176 pixels/160 x 120 pixels)
2 modes (FINE/STANDARD)
Approximate number of storable images
:
੬ pg. 39
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
79
For Connectors
S
S-Video input
:
:
Y: 0.8 V to 1.2 V (p-p), 75 Ω, analogue
C: 0.2 V to 0.4 V (p-p), 75 Ω, analogue
Y: 1.0 V (p-p), 75 Ω, analogue
C: 0.29 V (p-p), 75 Ω, analogue
S-Video output
AV
Video input
Video output
Audio input
Audio output
EDIT
:
:
:
:
:
:
Y: 0.8 V to 1.2 V (p-p), 75 Ω, analogue
Y: 1.0 V (p-p), 75 Ω, analogue
300 mV (rms), 50 kΩ, analogue, stereo
300 mV (rms), 1 kΩ, analogue, stereo
ø3.5 mm, 2-pole
Headphone output
DV
Stereo
Input/output
USB
:
:
4-pin, IEEE 1394 compliant
5-pin
AC Power Adapter/Charger
For General
Power requirement
Power consumption
Output
:
:
AC 110 V to 240 Vd, 50 Hz/60 Hz
23W
Charge
VTR
:
:
DC 7.2 V G, 1.2 A
DC 6.3 V G, 1.8 A
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject
to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
81
Controls
a •Menu Wheel [MENU]........................ ੬ pg. 31
•Speaker/Headphone Volume Control
No sound is output from the speaker when
[VOLUME +, –] ................................. ੬ pg. 20
b Snapshot Button [SNAPSHOT]....... ੬ pg. 23, 42
c Power Zoom Lever [T/W] .................... ੬ pg. 18
d •Exposure Adjustment Button
* i.Link refers to the IEEE1394-1995 industry
standard.
[EXPOSURE]...................................... ੬ pg. 46
•Blank Search Button
[BLANK SEARCH] ............................. ੬ pg. 21
e Dioptre Adjustment Control ................ ੬ pg. 12
f Recording Start/Stop Button................ ੬ pg. 17
g Power Switch [A, M, PLAY, OFF] ........ ੬ pg. 13
h Lock Button ......................................... ੬ pg. 13
i •Stop Button [8]................................. ੬ pg. 20
•Program AE Button [PROG.AE] ......... ੬ pg. 33
j •Rewind Button [3].......................... ੬ pg. 20
•NIGHT Button................................... ੬ pg. 42
k Play/Pause Button [4/9] .................... ੬ pg. 20
l •Fast-Forward Button [5] ................. ੬ pg. 20
•Wipe or Fader Effect Button
Connector ............................................੬ pg. 65
[AV]..........................................੬ pg. 22, 52, 61
Indicators
K Power Lamp....................................੬ pg. 13, 17
[FADE/WIPE]..................................... ੬ pg. 32
m Index Button [INDEX].......................... ੬ pg. 26
n Thumbnail Storing Button
[NAVI STORE]...................................... ੬ pg. 49
o •D.S.C. Playback Select Button
[SELECT].................................... ੬ pg. 24 – 29
•Navigation Button [NAVI] ................. ੬ pg. 48
p VIDEO/MEMORY Switch
[VIDEO/MEMORY].............................. ੬ pg. 13
q Title Button [TITLE].............................. ੬ pg. 51
r •Information Button [INFO]................ ੬ pg. 26
•E-Mail Clip Recording Button
k Battery Pack Mount..............................੬ pg. 10
n Speaker ................................................੬ pg. 20
p Tripod Mounting Socket .......................੬ pg. 12
q Card Cover [MEMORY CARD] ............੬ pg. 16
r Cassette Holder Cover..........................੬ pg. 15
s Lens Hood..............................................੬ pg. 6
t Flash.....................................................੬ pg. 43
u Stereo Microphone...............................੬ pg. 58
[E-MAIL]............................................ ੬ pg. 50
s Battery Release Switch
[BATT.RELEASE] ................................... ੬ pg. 10
t Cassette Open/Eject Switch
Light, VL-F3U Flash, MZ-V3U Stereo Zoom
Microphone or MZ-V5U Stereo Microphone.
Make sure to turn off the power of the camcorder
and the video light, flash or microphone before
attaching and removing them.
[OPEN/EJECT]...................................... ੬ pg. 15
u Manual Focus Ring............................... ੬ pg. 45
v Backlight Compensation Button
[BACK LIGHT] ..................................... ੬ pg. 47
w Manual Focus Button [FOCUS]............ ੬ pg. 45
x Monitor Opening Button
w Viewfinder............................................੬ pg. 12
x Remote Sensor .....................................੬ pg. 56
y Camera Sensor
Be careful not to cover this area, a sensor
necessary for shooting is built-in here.
z INFO LCD......................................੬ pg. 17, 23
[PUSH OPEN]...................................... ੬ pg. 17
Connectors
The connectors are located beneath the covers.
Y S-Video Input/Output Connector
[S-VIDEO]................................ ੬ pg. 22, 52, 61
Z Edit Connector [EDIT] ........................ ੬ pg. 61
Download from Www.Somanuals.com. All Manuals Search And Download.
82
Indications
LCD Monitor/Viewfinder Indications During
Video Recording Only
EN
INDEX Indications
(Blinks while the focus is being adjusted and
stops blinking when the focus is locked.)
c Shooting Icon
(੬ pg. 23)
(Appears and blinks during shooting.)
d Card Icon
(੬ pg. 23)
: Blinks in white when a memory card is not
loaded.
: Blinks in yellow while the camcorder is
titles/frames, NAVIGATION thumbnail
images, video clips, still images, etc.
1h40m
REC
(FINE) and
f Remaining Number Of Shot
(੬ pg. 39)
(੬ pg. 23)
SOUND 12 b i t
(Displays the approximate remaining number of
shots that can be stored during D.S.C. recording,
or the remaining number of storable thumbnail
images when it reaches 10 or less during video
depending on the Picture Quality/Image Size,
etc.)
15:55
r
a Navigation Indicator
(੬ pg. 48)
(Appears when “NAVIGATION” is set to other
than “MANUAL”.)
b Selected Wipe/Fader Effect Indicator
g Flash Indicator
(੬ pg. 43)
(੬ pg. 32)
(੬ pg. 17)
c Tape Running Indicator
(Rotates while tape is running.)
d Selected Wide Mode Indicator
e Thumbnail Storing Indicator
LCD Monitor/Viewfinder Indications During
(੬ pg. 36)
(੬ pg. 48)
(Appears while the captured image is being
stored as a thumbnail image in the memory
card.)
f Recording Speed Mode (SP/LP)
g Tape Remaining Time
h •REC: (Appears during recording.)
•PAUSE: (Appears during Record-Standby
mode.)
i Insert Editing/Insert Editing Pause Mode
(੬ pg. 34)
(੬ pg. 18)
(੬ pg. 17)
E-
CL IP
0
h
1: 0
m
00 : 15
(੬ pg. 17)
a Image Size: 160 (160 x 120), 240 (240 x 176)
(੬ pg. 38)
(੬ pg. 23)
(੬ pg. 59)
b Shooting Icon
j 5S/Anim.: Displays the 5-Second Recording
mode or Animation recording mode. (੬ pg. 36)
k Wind Cut Indicator
l Sound Mode Indicator
(Appears for approx. 5 seconds after turning on
the camcorder.)
m Time Code
n Digital Image Stabiliser (“DIS”)
(Appears and blinks during shooting.)
c E-Mail Clip Recording Indicator
(੬ pg. 50)
(੬ pg. 36)
(੬ pg. 34)
d Memory Card Remaining Time For E-Mail Clip
Recording
e E-Mail Clip Recording Time
(੬ pg. 50)
(੬ pg. 50)
(੬ pg. 38, 41)
(੬ pg. 35)
LCD Monitor/Viewfinder Indications During
LCD Monitor/Viewfinder Indications During
D.S.C. Recording Only
g
8
9
0
1
2
40
x
W
T
O
q
3
3
1024
4
5
6
15
w
g
3
7
BRIGHT
7
e
a Image Size: 1600 (1600 x 1200), 1280
1 0 . 11 03
.
(1280 x 960), 1024 (1024 x 768) or 640
(640 x 480)
10 : 00
(੬ pg. 39)
(੬ pg. 23)
b Focus Icon
y
t
r
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
83
a Operation Mode
(੬ pg. 13)
(੬ pg. 42)
e •U : Playback
b •
: Night-Scope Indicator
•5
: Fast-Forward/Shuttle Search
: Rewind/Shuttle Search
(Appears when Night-Scope is engaged.)
: Gain Up Mode (੬ pg. 35)
•3
•
(Appears when “GAIN UP” is set to “AUTO”
and the shutter speed is automatically
adjusted.)
•9 U : Forward Frame-By-Frame Playback/
Slow-Motion
•Y 9 : Reverse Frame-By-Frame Playback/Slow-
Motion
c Red Eye Reduction Indicator
(੬ pg. 43)
(Appears when the “B-IN FLASH” is set to
“AUTO C”.)
•9D : Audio Dubbing Pause
f Sound Input For Audio Dubbing
h Date/Time
d White Balance Indicator
(੬ pg. 47)
e • : Backlight Compensation Indicator
(੬ pg. 58)
(੬ pg. 84)
(੬ pg. 47)
• : Exposure Adjustment Indicator (੬ pg. 46)
f Selected Program AE With Special Effects
(੬ pg. 38, 41)
Indicator
(੬ pg. 33)
(੬ pg. 46)
(੬ pg. 18)
(੬ pg. 20)
g Iris Lock Indicator
h Approximate Zoom Ratio
(Appears during zooming.)
i Zoom Indicator
monitor/Viewfinder)
(The level indicator g moves.)
j Time Code
(੬ pg. 13)
(੬ pg. 18)
(Appears during zooming.)
(The level indicator g moves.)
j Self-Timer Recording Indicator
(੬ pg. 38, 41)
(੬ pg. 44)
LCD Monitor/Viewfinder Indications During
D.S.C. Playback
k O: (Appears when taking Snapshot.)
(੬ pg. 42)
l BRIGHT: Brightness Control Indicator (LCD
monitor/Viewfinder)
(The level indicator g moves.)
m Battery Indicator
n Date/Time
(੬ pg. 13)
1
2
100-0013
(੬ pg. 84)
(੬ pg. 14)
o Manual Focus Adjustment Indicator (੬ pg. 45)
p Flash Indicator (੬ pg. 43)
(Appears when the flash is ready. A number
appears next to the indication after adjusting the
brightness of the flash.)
BR I GHT
LCD Monitor/Viewfinder Indications During
Video Playback
g
4
3
(੬ pg. 26)
(੬ pg. 26)
(੬ pg. 84)
1
2
3 4 5
6
12 b i t / SOUND
L
1
d Brightness Control Indicator (LCD monitor/
Viewfinder)
(੬ pg. 13)
MIC
(The level indicator g moves.)
BLANK SEARCH
PUSH "STOP" BUTON
TO CANCEL
VOLUME
7
1 0 . 11 03
.
20 : 21 : 25
10 : 00
g
0
8
9
a Sound Mode Indicator
b Blank Search Indicator
c Thumbnail Storing Indicator
(੬ pg. 40)
(੬ pg. 21)
(੬ pg. 49)
(Appears while the captured image is being
stored as a thumbnail image in the memory
card.)
d Tape Speed
(੬ pg. 34)
Download from Www.Somanuals.com. All Manuals Search And Download.
84
EN
INDEX Indications (cont.)
Warning Indications
Indications
Function
Displays the battery remaining power.
Remaining power level: high
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator blinks.
When the battery power is exhausted, power turns off automatically.
Appears when no tape is loaded.
(੬ pg. 15)
Appears when the erase protection tab is set to “SAVE” while the Power Switch is
set to “A” or “M” and the VIDEO/MEMORY Switch is set to “VIDEO”.
(੬ pg. 13)
CHECK TAPE’S ERASE
PROTECTION TAB
Appears if dirt is detected on the heads during recording. Use an optional
cleaning cassette.
HEAD CLEANING
REQUIRED USE
CLEANING CASSETTE
Appears if condensation occurs. When this indication is displayed, wait more
than 1 hour until condensation disappears.
CONDENSATION
OPERATION PAUSED
PLEASE WAIT
Appears if a tape is not loaded when the Recording Start/Stop Button or
SNAPSHOT Button is pressed while the Power Switch is set to “A” or “M” and
the VIDEO/MEMORY Switch is set to “VIDEO”.
TAPE!
TAPE END
Appears when the tape ends during recording or playback.
(੬ pg. 67)
● Appears when the date/time is not set.
(੬ pg. 14)
SET DATE/TIME!
● Appears when the built-in clock (lithium) battery is discharged and the
previously set date/time is erased.
(੬ pg. 14)
LENS CAP
Appears for 5 seconds after power is turned on if the lens cap is attached.
Appears if Audio Dubbing is attempted on a blank portion of a tape. (੬ pg. 58)
A. DUB ERROR!
A. DUB ERROR!
● Appears if Audio Dubbing is attempted on a tape recorded in the LP mode.
(੬ pg. 58)
<CANNOT DUB ON A
LP RECORDED TAPE> ● Appears if Audio Dubbing is attempted on a tape recorded in 16-bit audio.
<CANNOT DUB ON A
(੬ pg. 58)
16bit RECORDING> ● Appears if A. DUB (D) on the remote control is pressed when the erase
<CHECK TAPE’S
ERASE PROTECTION
TAB>
protection tab is set to “SAVE”.
(੬ pg. 58)
INSERT ERROR!
Appears if Insert Editing is attempted on a blank portion of a tape.
(੬ pg. 59)
INSERT ERROR!
● Appears if Insert Editing is attempted on a tape recorded in the LP mode.
(੬ pg. 59)
<CANNOT EDIT ON A
LP RECORDED TAPE> ● Appears if INSERT (I) on the remote control is pressed when the erase
<CHECK TAPE’S
ERASE PROTECTION
TAB>
protection tab is set to “SAVE”.
(੬ pg. 59)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
85
Indications
Function
MEMORY IS FULL
Appears when the memory card’s memory is full and shooting is not possible.
● Appears if dubbing of copyguarded signals is attempted while this camcorder is
being used as a recorder.
● Appears in the following cases when dubbing from a tape to a memory card (as
digital stills or video clips):
COPYING FAILED
– when no memory card is loaded.
– when the memory card’s memory is full.
– when the memory card is not formatted.
– when a write-protected SD Memory Card is loaded.
(੬ pg. 50, 55)
Appears if there is no memory card loaded when you attempt to record on a
memory card or access data on a memory card.
MEMORY CARD!
PLEASE FORMAT
NO IMAGES STORED
Appears when there is a problem with a memory card and its memory is corrupt,
or it has not been initialised. Initialise the memory card.
(੬ pg. 30)
Appears if there are no image files stored in the memory card when you attempt
memory card playback.
NO E-MAIL CLIP
STORED
Appears if there are no video clip files stored in the memory card when you
attempt memory card playback.
● Appears if there are no title/frame files stored in the memory card when you
attempt to use titles/frames.
● Appears when you attempt to use titles/frames during video playback.
NO TITLE DATA
STORED
Appears when the camcorder does not recognise the loaded memory card.
Remove the memory card once and insert it again. Repeat these procedures until
no indication appears. If the indication still appears, the memory card is
corrupted.
CARD ERROR!
Appears when playing back a file that is not compatible with DCF or a file with a
size that is not compatible with this camcorder.
UNSUPPORTED FILE!
CHECK CARD’S WRITE
● Appears when you attempt to shoot digital still images when the write
protection tab on the SD Memory Card is set to the “LOCK” position.
PROTECTION SWITCH ● Appears when you attempt MEMORY SELECT menu operation with a write-
protected SD Memory Card loaded.
The error indications (E01, E02 or E06) show what type of malfunction has
E01, E02 or E06
occurred. When an error indication appears, the camcorder turns off
UNIT IN SAFEGUARD
automatically. Remove the power supply (battery, etc.) and wait a few minutes for
MODE REMOVE AND
the indication to clear. When it does, you can resume using the camcorder. If the
REATTACH BATTERY
indication remains, consult your nearest JVC dealer.
The error indications (E03 or E04) show what type of malfunction has occurred.
E03 or E04
When an error indication appears, the camcorder turns off automatically. Eject
UNIT IN SAFEGUARD
the cassette once and re-insert it, then check if the indication clears. When it
MODE EJECT AND
does, you can resume using the camcorder. If the indication remains, consult
REINSERT TAPE
your nearest JVC dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
86
EN
A
G
Animation ...........................................................36
Audio Dubbing ...................................................58
Auto Focus ..........................................................45
Auto Playback Of Images ....................................24
I
B
Backlight Compensation ......................................47
Battery Pack ............................................10, 11, 74
Beep (BEEP) .........................................................37
Blank search ........................................................21
Brightness Adjustment Of The Display
(BRIGHT) ............................................................13
Built-in Clock’s Rechargeable Lithium Battery .....14
C
Changing The Menu Settings ...............................31
Channels (Left/Right) ...........................................40
Cleaning The Camcorder .....................................77
Connections
L
Loading A Cassette .............................................. 15
Charging .......................................................10
To A TV Or VCR ...........................................22
MANUAL ..................................................... 35
SYSTEM ..................................................37, 41
VIDEO ..........................................................40
D
Date/Time
Settings .........................................................14
Deleting Files (DELETE) .......................................28
Deleting thumbnail images (NAVI.DEL.) ..............40
Demonstration Mode (DEMO MODE) .............9, 37
Dubbing from tape to memory card
N
(
COPY) .........................................40, 55
E
E-Mail Clip Recording (E-CLIP REC) ...............38, 50
Erase Protection .............................................15, 16
Exposure Control (EXPOSURE) ............................46
F
Fade-In/Out .........................................................32
Fast-Forward The Tape ........................................20
Flash (B-IN FLASH) ........................................37, 43
Flash Brightness Adjustment (FLASH ADJ.) ..........43
Frame-By-Frame Playback ...................................57
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
P
Picture Quality (QUALITY) ..................................39
Playback sound
(SOUND MODE, 12bit MODE) ...........................40
Power Switch Position .........................................13
Priority Setting (PRIORITY) ..................................38
Classic Film (CLASSIC FILM) .........................33
Sepia (SEPIA) .................................................33
Shutter Speed (SHUTTER) .............................33
Sports (SPORTS) ............................................33
Spotlight (SPOTLIGHT) .................................33
Provided Accessories .............................................5
Viewfinder Adjustment .......................................12
R
Recording media selection (REC SELECT) ............39
Recording Time
Z
Zooming (ZOOM) .........................................18, 34
Tape .............................................................15
Record-Standby ...................................................17
Remaining Power Level .......................................84
Remote Control ...................................................56
Remote control setting (REMOTE) ........................37
Resetting Menu Settings (CAM RESET) .................38
Resetting The File Name ......................................29
S
Self-Timer (SELF-TIMER) ................................35, 44
Set Remote/VCR Code .........................................60
Shuttle Search .....................................................21
Slow-Motion Playback ........................................57
Snapshot .......................................................23, 42
Snapshot Mode (SNAP MODE) ............................34
Sound Mode (SOUND MODE) ......................34, 40
Speaker Volume ..................................................20
Specifications ................................................78, 79
Still Playback .......................................................20
S-Video/AV input (S/AV INPUT) ....................40, 52
Synchro adjustment (SYNCHRO) .........................64
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Printed in Japan
0203-FO-ID-VP
COPYRIGHT© 2003 VICTOR COMPANY OF JAPAN, LTD.
EK
Download from Www.Somanuals.com. All Manuals Search And Download.
|