DVD PLAYER &
VIDEO CASSETTE RECORDER
HR-XVS44UJ
For Customer Use:
Enter below the Model No. and
Serial No. which are located on the
rear of cabinet. Retain this
INSTRUCTIONS
information for future reference.
Model No.
Serial No.
LPT0857-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
3
Use only discs marked with the following.
2. DO NOT block the unit’s ventilation openings or
holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
DVD
(8 cm /12 cm disc)
3. DO NOT place heavy objects on the unit or Remote.
4. DO NOT place anything which might spill on top of
the unit or Remote.
Video CDs
(8 cm /12 cm disc)
(If water or liquid is allowed to enter this equipment,
fire or electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or
splashing.
Audio CDs
(8 cm /12 cm disc)
6. DO NOT use this equipment in a bathroom or places
with water. Also DO NOT place any containers filled
with water or liquids (such as cosmetics or medicines,
flower vases, potted plants, cups, etc.) on top of this
unit.
SVCD
(8 cm /12 cm disc)
7. DO NOT place any naked flame sources, such as
lighted candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
● Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarks of Dolby
Laboratories.
● “DTS” and “DTS Digital Out” are trademarks of Digital
Theater Systems, Inc.
● Cassettes marked “S-VHS” and “VHS” can be used with this
unit. However, S-VHS recordings are possible only with
cassettes marked “S-VHS”.
By using the S-VHS ET function, it is possible to record and
play back with S-VHS picture quality on VHS cassettes with
this unit.
● This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing users only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly
is prohibited.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you
move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form
in the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the
tape. In conditions where condensation may occur, keep
the unit turned on for a few hours to let the moisture dry.
ATTENTION
To mobile phone users:
Using a mobile phone in the vicinity of the unit may
cause picture vibration on the TV screen or change
the screen to a blue back display.
On placing the unit:
Some TVs or other appliances generates strong
magnetic fields. Do not place such appliance on top
of the unit as it may cause picture disturbance.
When the equipment is installed in a cabinet or a shelf,
make sure that it has sufficient space on all sides to allow
for ventilation (10 cm or more on both sides, on top and
at the rear.)
When discarding batteries, environmental problems must
be considered and the local rules or laws governing the
disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, Remote or video cassette.
1. DO NOT place the unit —
— in an environment prone to extreme temperatures
or humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
— on a surface that is unstable or subject to vibration.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
EN
About Discs ......................................................... 5
INDEX
8
INSTALLING YOUR NEW UNIT
12
Plug & Play Set .................................................. 15
Basic Recording ................................................ 30
90
Parental Lock .................................................... 56
About MP3/WMA Disc ...................................... 60
MP3/WMA Playback ......................................... 61
About JPEG Disc ............................................... 63
JPEG Playback ................................................... 64
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5
DISC INFORMATION
Unplayable Discs
About Discs
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
Playable Discs
● CD-ROM discs (including PHOTO-CD)
● DVD AUDIO discs
● Super Audio CDs (SACD)
● DVD-RW discs recorded in VR format
● DVD-RAM
● Discs which have a region number other than “1”
You can use the discs with the following logos for playback only.
DVD VIDEO
Video CD/Super Video CD
Region Number
Audio CD
The world is divided into 6 regions for DVD VIDEO discs. DVD
VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is “1”. Only discs
whose region number includes “1” can be played back such as
shown below.
CD-DA
files
● The following discs also can be played back.
• DVD-R/RW discs recorded in DVD VIDEO format and
finalized
• CD-R/RW discs recorded in Super Video CD, Video CD or
Audio CD format and finalized.
Examples of DVD VIDEO labels which can be played back using
this unit.
• CD-R/RW discs recorded in MP3/WMA format in
accordance with the “ISO 9660” format. (See page 60 for
details.)
• CD-R/RW discs recorded in JPEG format in accordance with
the “ISO 9660” format. (See page 63 for details.)
● Discs other than the above cannot be played back.
● Operation and audio quality of this unit are not guaranteed for
discs that do not conform to the Compact Disc specification
(CD-DA).
Before you play back a CD, check for the CD logo and read
the notes on the package to confirm that it conforms to the
Compact Disc specification.
● Depending on the intentions of the author of the software,
recording conditions of DVD discs and Video CD discs may
be restricted. Since this unit plays back discs according to the
intentions of the author of the software as indicated on the
disc, some functions may not operate as commanded.
● When switching from the first layer to the second layer of
double-layered DVD VIDEO discs, the image and sound may
be momentarily distorted. This is not a malfunction.
Marks of discs in this instruction manual
Allows operation
with a DVD VIDEO
disc.
Allows operation
with a CD-R/RW
disc.
Allows operation
with a Video CD
disc.
Allows operation
with a SVCD disc.
Allows operation
with a disc
including MP3/
WMA files.
Allows operation
with a disc
including JPEG files.
Allows operation
with a Audio CD
disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EN
DISC INFORMATION (cont.)
DVD VIDEO Marks
File Structure of Discs
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of a disc. Check marks indicating the contents and
functions of a disc. Note, however, that in some cases a disc may
not include a mark even for a function it supports.
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used
to select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that
can also be used to select desired chapters. Note that some discs
are not divided into titles and chapters.
Marks related to video
Title 1
Title 2
Mark
Description
Number of subtitles
Chapter 1
Chapter 2
Chapter 3
Chapter 1 Chapter 2
Audio CD/Video CD
Number of angles
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD
discs.
Recorded under the standard 4:3 aspect
ratio
Track 1
Track 2
Track 3
Track 4
NOTE:
Screen includes black bands at top and
bottom of image which has a standard 4:3
aspect ratio (letter box)
Video CD discs that support Playback Control (PBC)
The still image or motion image which follows a menu screen is
called a “scene”. Each scene has a scene number.
For more details, refer to “Locating a desired scene using the
menu of the Video CD with PBC” (੬ pg. 41).
Video playback is in Wide video mode
(16:9) on wide televisions, but in letter
box on televisions with standard 4:3
aspect ratio.
Video playback is in Wide video mode
(16:9) on wide televisions, but pan and
scan is used on televisions with standard
4:3 aspect ratio (either the left or right side
of the image is cut-out).
Marks related to audio
Mark
Description
Number of audio tracks
Dolby Digital mark
Dolby Laboratories has developed a
digital surround system for the home. This
mark indicates that you may enjoy 5.1-
channel audio (front left and right, center,
rear left and right, and a channel for LFE
(Low-Frequency Effects)).
DTS (Digital Theater System)
You can enjoy DTS audio if you connect
the amplifier with a built-in DTS decoder
to the DIGITAL AUDIO OUT connector of
the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
7
Placing a Disc
Care and Handling of Discs
How to handle discs
1 Open the disc tray.
When handling a disc, do
Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
not touch the surface of the
disc. Since discs are made
of plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped,
the images and sound will
not be picked up correctly,
and such a disc may cause the unit to malfunction.
x
Label side
Do not damage the label side, stick paper to or use any adhesive
on its surface.
Storage
● Pressing the button again closes the disc tray.
● Do not block the disc tray with your hand while it is opening
or closing as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc
in the disc tray.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt
adhering to a disc, wipe with a soft dry
cloth, moving from the center outwards.
If a disc is difficult to clean, wipe with a
cloth moistened with water. Never use
record cleaners, petrol, alcohol or any
anti-static agents.
2 Place the disc.
Place the disc in the disc tray
with the label side facing up.
● Since disc size changes depending
on the disc to be played back, be
sure to correctly align the disc with
the grooves for its size. If the disc is
not in its groove, it may be
CAUTION
scratched or otherwise damaged.
● To insert an 8 cm disc, place it
according to the inner groove.
Sometimes during playback, noise or images may be garbled.
This is sometimes due to the disc. (It may not be up to
industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
EN
INDEX
FRONT VIEW
C VHS Cassette Loading Slot
D VCR/DVD Button ੬ pg. 26, 30, 40
(S-VIDEO/VIDEO/AUDIO) ੬ pg. 66
L Remote Sensor
M Front Display Panel ੬ pg. 9
G DVD Indicator ੬ pg. 40
O Rewind Button (REW (3)) ੬ pg. 26, 27, 42
P Fast Forward Button (FF (5)) ੬ pg. 26, 27, 42
Q Channel Button (CH +/–) ੬ pg. 30
R Progressive Scan Button (PROGRESSIVE SCAN)
੬ pg. 82
H Play Button (PLAY (4)) ੬ pg. 26, 40
I DVD Open/Close Button (OPEN/CLOSE (x))
੬ pg. 40
J VHS Eject Button (EJECT (x)) ੬ pg. 26, 30
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
9
REAR VIEW
A Region Number Label ੬ pg. 5
B AC Power Cord ੬ pg. 12
(S-VIDEO/VIDEO/AUDIO INPUT (L-1))
D S-Video/Video/Audio Output Connectors
(S-VIDEO/VIDEO/AUDIO OUTPUT) ੬ pg. 12,
13, 14, 67
E Antenna Input Connector (VHF/UHF IN)
੬ pg. 12
F Digital Audio Output Connector
G Audio Output Connectors (AUDIO OUTPUT
(L/R))*
* These are analogue audio output connectors for DVD deck only.
(COMPONENT VIDEO OUT) ੬ pg. 14
I Remote Pause Connector (REMOTE PAUSE)
੬ pg. 66
J Antenna Output Connector (VHF/UHF OUT)
੬ pg. 12
FRONT DISPLAY PANEL
A Progressive Mode Indicator ੬ pg. 82
B “Timer” Indicator (VCR deck only) ੬ pg. 35
C Satellite Auto Recording Indicator (N) (VCR deck
only) ੬ pg. 39
E VCR Mode Indicator
F VCR Indicator ੬ pg. 31
G Cassette Type Indicator (VCR deck only)
H Channel Mode Indicator (CH)
I Remain Display ੬ pg. 32
J DVD Mode Indicator
D Channel/Clock
Mode Display (F-1 or L-1) (VCR deck only)
Counter Display (VCR deck)
Tape Speed (SP/EP) (VCR deck only)
Multi-information window* (DVD deck)
* The current group/title/track/chapter number(s), time and status
information.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
EN
INDEX (cont.)
ON-SCREEN DISPLAY (VCR deck)
If you press DISPLAY on the Remote when “SUPERIMPOSE” is set to “ON” (੬ pg. 75), various operational indicators
appear on the TV screen.
For On-screen display for DVD deck, refer to “Using the on-screen bar” (੬ pg. 46).
A Operation Mode Indicators
B Tape Speed (SP/EP)
D Index number ੬ pg. 28
E Tape Remaining Time Indicator ੬ pg. 32
F Counter Display
G Audio Mode Display ੬ pg. 29
H SAP Indicator ੬ pg. 32
I Stereo Program Indicator ੬ pg. 32
J Day/Clock Display
K Channel Position Number/Auxiliary Input
Indicator (F-1 or L-1)
L “Cassette Loaded” Mark
The tape position indicator
appears on the TV screen
when you press REW (3)
or FF (5) from the Stop
mode or perform an Index
Search. (੬ pg. 28) The
position of “q” in relation to
“0” (beginning) or “+” (end)
shows you where you are
Beginning
End
on the tape.
NOTE:
To recall an indication
A Press DISPLAY.
Depending on the type of tape being used, the tape position
indicator may not appear correctly.
● All indications corresponding to the current status are
displayed for 5 seconds. After that, the counter
information and RECORD/PAUSE if in the Record Pause
mode, remain on the screen.
B Press DISPLAY again to clear the display.
● The RECORD/PAUSE indication remains on the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
11
੬ pg. 28, 41
REMOTE
Review Button (
)
O rt Button ੬ pg. 16
੬ pg. 71
Q 3D-Phonic Button (3D-PHONIC) ੬ pg. 44
S DVD Button ੬ pg. 40
U TV Muting Button (MUTE) ੬ pg. 71
Audio Monitor Button (A.MONITOR)
੬ pg. 29, 54, 55
V TV/VCR Button ੬ pg. 31
W Date Button (DATE +/–) ੬ pg. 34
Angle Button (ANGLE) ੬ pg. 53
* With this button, you can also adjust the brightness of front
display panel.
+: brightens the display
–: darkens the display
Z Timer Button (TIMER) ੬ pg. 35
b Program Check Button (PROG. CHECK)
੬ pg. 36
Return Button (RETURN) ੬ pg. 41
੬ pg. 39
੬ pg. 28, 41
i OK Button ੬ pg. 16
j w e Button ੬ pg. 16
be used to operate your TV. (੬ pg. 71)
k Display Button (DISPLAY) ੬ pg. 32
l Skip Search Button (SKIP SEARCH) ੬ pg. 28
DVD Picture Button (DVD PICTURE) ੬ pg. 45
A VCR Button ੬ pg. 26, 30
B TV/VCR/DVD switch ੬ pg. 16
D SP/EP Button ੬ pg. 30
Before use, insert two AA size batteries into the Remote with
the polarity ( and ) matched correctly as indicated on
the battery compartment or on the lid.
Title Button (TITLE) ੬ pg. 62
F Start Time Button (START +/–) ੬ pg. 34
Zooming Button (ZOOM) ੬ pg. 43
G Number Keys ੬ pg. 25, 30, 62
H Daily Button (DAILY) ੬ pg. 35
10 Button
The Remote can operate most of your unit’s functions, as well
as basic functions of TV sets of JVC and other brands.
(੬ pg. 71)
● Point the Remote toward the remote sensor.
● The maximum operating distance of the remote control is
about 8 m.
If the Remote doesn’t work properly, remove its batteries,
wait a short time, replace the batteries and then try again.
J Play Button (PLAY (4)) ੬ pg. 26, 40
K Rewind Button (REW (3)) ੬ pg. 26, 27, 42
L Stop Button (STOP (8)) ੬ pg. 26, 30, 40
M Record Button (REC (7)) ੬ pg. 30
Download from Www.Somanuals.com. All Manuals Search And Download.
12
EN
INSTALLING YOUR NEW UNIT
C Connect the unit to TV.
Basic Connections
The connection method you use depends on the type of
TV you have.
Antenna or Cable
RF Connection
8To connect to a TV with NO AV input connectors —
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the VHF/UHF IN
connector on the rear panel of the unit.
Coaxial cable
Flat feeder
TV’s antenna terminal.
Matching transformer
(not supplied)
AV Connection
8To connect to a TV with AV input connectors —
AUDIO
AC Outlet
AC Power Cord
A Connect the antenna, unit and TV as per “RF
OUTPUT
Connection”.
VIDEO OUTPUT
B Connect an optional audio/video cable between the
AUDIO/VIDEO OUTPUT connectors on the rear
panel of the unit and the TV’s audio/video input
connectors.
● Set your TV to AV mode.
● For switching the TV’s mode, refer to the instruction manual of
your television.
● To obtain high-quality pictures, you can also use the S-VIDEO
connection or Component Video Connection (DVD deck
only). (੬ pg. 13, 14)
Back of unit
VHF/UHF
IN
D Connect the unit to power source.
VHF/UHF OUT
Audio/video cable
(not supplied)
Plug the end of the AC power cord into an AC outlet. This
unit performs Plug & Play Set automatically. (੬ pg. 15)
● The clock and tuner channels will automatically be set when
the antenna is connected and when the AC power cord is first
connected to an AC outlet. (If “AUTO” and the channel
indicator are displayed on the front display panel before the
unit is powered on, the clock and tuner channels are being set
automatically. Wait for the time to be displayed on the front
display panel before turning on the unit.)
To Audio/video
input connectors
RF cable
(supplied)
To 75 ohm
Terminal
E Set the VCR channel.
TV
The VCR channel is the channel on which you can watch
the picture from the unit on the TV when only using RF
connection.
It’s essential that your unit be properly connected.
With RF connection, set the VCR channel to “3 CH” or
“4 CH”.
● The VCR channel is preset to “3 CH”. Set to “4 CH” if the
Channel 3 is used for broadcasting in your area.
With AV connection, set the VCR channel to “– CH” (off).
To set the VCR channel, perform the following steps:
THESE STEPS MUST BE COMPLETED BEFORE ANY
A Check the contents.
Make sure the package contains all of the accessories
listed in “SPECIFICATIONS” on page 89.
Before performing the following steps:
● Make sure there is no cassette inserted in the unit.
● Make sure the unit is turned on, then press VCR/
DVD on the unit or VCR on the Remote so that the
VCR indicator lights up.
B Situate the unit.
Place the unit on a stable, horizontal surface.
A Press POWER (1) to turn off the unit, then press
STOP (8) on the unit for more than 5 seconds. “3 CH”
appears on the front display panel.
B Press CH +/– on the Remote to select “3 CH”, “4 CH”
or “– CH” (off), then press OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
13
8To connect to a TV with S-VIDEO/AUDIO input
S-VIDEO
A Connect the unit to TV.
Connection
A Connect the antenna, unit and TV as per “RF
Connection”. (੬ pg. 12)
B Connect an optional audio cable between the AUDIO
OUTPUT connectors on the rear panel of the unit and
the TV’s audio input connectors.
Antenna or Cable
C Connect the unit’s S VIDEO OUTPUT connector to the
TV’s S-VIDEO input connector.
Coaxial cable
Flat feeder
B Connect the unit to power source.
Plug the end of the AC power cord into an AC outlet. This
unit performs Plug & Play Set automatically. (੬ pg. 15)
● The clock and tuner channels will automatically be set when
the antenna is connected and when the AC power cord is first
connected to an AC outlet. (If “AUTO” and the channel
indicator are displayed on the front display panel before the
unit is powered on, the clock and tuner channels are being set
automatically. Wait for the time to be displayed on the front
display panel before turning on the unit.)
Matching transformer
(not supplied)
AC outlet
S VIDEO OUTPUT
AUDIO OUTPUT
AC power cord
C Set the VCR channel to off.
Before performing the following steps:
● Make sure there is no cassette inserted in the unit.
● Make sure the unit is turned on, then press VCR/
DVD on the unit or VCR on the Remote so that the
VCR indicator lights up.
Back of unit
VHF/UHF
IN
A Press POWER (1) to turn off the unit, then press
appears on the front display panel.
B Press CH +/– on the Remote to select “– CH” (off),
then press OK.
S-Video cable
(supplied)
Audio cable
(not supplied)
VHF/UHF
OUT
RF cable
(supplied)
NOTES:
● You can obtain high-quality S-VHS pictures.
● If your TV is not stereo-capable, use the unit’s AUDIO
OUTPUT (DVD/VCR) connectors to connect to an audio
amplifier for Hi-Fi stereo sound reproduction.
● To operate the unit with your TV using the S-VIDEO
connection, set your TV to its AV mode. You can also use the
TV/VCR button on the unit’s Remote to set your TV to the AV
mode. (੬ pg. 71)
To 75 ohm
Terminal
To S-VIDEO input
connector
● For switching the TV’s mode, refer to the instruction manual of
your television.
TV
Download from Www.Somanuals.com. All Manuals Search And Download.
14
EN
INSTALLING YOUR NEW UNIT (cont.)
8To connect to a TV with component video input
Component Video
Connection
A Connect the unit to TV.
A Connect the aerial, unit and TV as per “AV
Connection”. (੬ pg. 12)
B Connect the unit’s COMPONENT VIDEO OUT
connectors to the TV’s component video input
connectors.
(DVD deck only)
ATTENTION
B Connect the unit to power source.
Be sure to connect the unit’s VIDEO OUTPUT (DVD/
VCR) connector to the TV’s VIDEO input connector.
Plug the end of the AC power cord into an AC outlet. This
unit performs Plug & Play Set automatically. (੬ pg. 15)
● The clock and tuner channels will automatically be set when
the antenna is connected and when the AC power cord is first
connected to an AC outlet. (If “AUTO” and the channel
indicator are displayed on the front display panel before the
unit is powered on, the clock and tuner channels are being set
automatically. Wait for the time to be displayed on the front
display panel before turning on the unit.)
Antenna or Cable
Coaxial cable
Flat feeder
C Set the VCR channel to off.
Before performing the following steps:
Matching transformer
(not supplied)
● Make sure there is no cassette inserted in the unit.
● Make sure the unit is turned on, then press VCR/
DVD on the unit or VCR on the Remote so that the
VCR indicator lights up.
AUDIO
COMPONENT
VIDEO OUT
AC outlet
AC power cord
OUTPUT
VIDEO OUTPUT
A Press POWER (1) to turn off the unit, then press
STOP (8) on the unit for more than 5 seconds. “3 CH”
appears on the front display panel.
B Press CH +/– on the Remote to select “– CH” (off),
then press OK.
NOTES:
● You can obtain high-quality component video pictures when
you play back discs on the DVD deck.
Back of unit
VHF/UHF
IN
● If your TV is not stereo-capable, use the unit’s AUDIO
OUTPUT (DVD/VCR) connectors to connect to an audio
amplifier for Hi-Fi stereo sound reproduction.
● To operate the unit with your TV using the Component Video
connection, set your TV to its AV mode. You can also use the
TV/VCR button on the unit’s Remote to set your TV to the AV
mode. (੬ pg. 71)
Audio/Video
Component
Video cable
(not supplied)
VHF/UHF
OUT
cable
(not supplied)
● For switching the TV’s mode, refer to the instruction manual of
your television.
RF cable
(supplied)
To Component Video
Input connectors
To 75 ohm
Terminal
TV
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
15
INITIAL SETTINGS
This unit sets the clock and tuner channels automatically
when AC power cord is first connected to an AC outlet.
The antenna cable must be connected for the Plug & Play
setting.
The time and date can be set automatically by the clock
setting data transmitted from one of the regular TV
broadcast channels. We call this TV channel the “host
channel” and it is a PBS channel in your area.
Plug & Play Set
Auto Clock Set/Auto Tuner Set
ATTENTION
● If you use a cable box, Plug&Play will not function; set the
clock and tuner channels separately. (੬ pg. 22 – 25)
● Depending on areas or reception conditions, the unit may
not receive the Auto clock setting data from the PBS
channel. If this function is taking a considerable amount of
time, it may be necessary to perform the Semiauto or
Manual Clock Set procedure.
A Perform Plug & Play setup.
Connect the antenna cable to the unit. (੬ pg. 12) Then
connect the AC power cord to an AC outlet. Do not turn
on the unit.
The clock and tuner channels will be set automatically.
NOTES:
● Auto Clock Set is performed first.
“AUTO” blinks on the front display panel during Auto Clock
Set.
Channel Set, the channel numbers are displayed as they are
● When Plug & Play setting has been complete successfully, the
correct clock time is displayed. If you perform Plug & Play
setting successfully, there is no need to perform “Clock Set”
(੬ pg. 22) and “Tuner Set” (੬ pg. 24). If, however, you want
to add or delete channels, refer to “Manual Channel Set”
(੬ pg. 25).
During Initial Auto Clock Set
“AUTO” blinks.
During Auto Channel Set
The channel numbers are displayed as they are
Plug&Play Completed
The current time is displayed.
* If an incorrect clock time or “– –:– –” appears on the front display panel, see “What to do if Plug & Play setting failed” below.
INFORMATION
● If “AUTO CLOCK” is set to “ON” (੬ pg. 23), the clock will be adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming PBS channel clock setting data. (This automatic clock
adjustment can only be performed when the unit is turned off. The clock will be adjusted just on these hours — on the time
displayed on the front display panel, not on the actual real time.) The default setting of “AUTO CLOCK” is “ON”. (੬ pg. 23)
● If the memory backup fails, because a power outage occurs or because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an
adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform “Semiauto Clock Set” (੬ pg. 23)
or “Manual Clock Set” (੬ pg. 23).
● If “– –:– –” appears on the front display panel, your antenna cable may not be connected to the unit or there may not be a Host
PBS signal available in your area. Ensure that the antenna cable is connected correctly. Then turn on and off the unit; the Plug &
Play setting will be automatically reactivated. If Plug & Play setting is not performed though the antenna cable is connected
correctly, perform “Manual Clock Set” (੬ pg. 23) and “Auto Channel Set” (੬ pg. 24) or “Manual Channel Set” (੬ pg. 25).
Download from Www.Somanuals.com. All Manuals Search And Download.
16
EN
INITIAL SETTINGS (cont.)
A Turn on the unit.
Monitor Set
Press POWER (1).
(DVD deck)
B Select the DVD deck.
You can select the monitor type depending the TV used
when you play back DVD VIDEO discs recorded for
wide-screen TVs.
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
C Access the DVD Set Up menu screen.
PICTURE
A Press SET UP MENU.
B Press w e to select
MONITOR TYPE
PICTURE SOURCE
SCREEN SAVER
4:3LB
AUTO
“
PICTURE”.
ON
MP3&WMA
/
JPEG
MP3&WMA
SELECT
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
OK
D Select the mode.
Press rt to move H to
“MONITOR TYPE”, then
press OK.
PICTURE
MONITOR TYPE
PICTURE SOURCE
SCREEN SAVER
MP3&WMA JPEG
4:3LB
AUTO
ON
/
MP3&WMA
SELECT
OK
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
E Select the mode setting.
Press rt to select the desired setting, then press OK.
F Return to the normal screen.
Press SET UP MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
17
* The default setting is bold in the table below.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen
TV with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect
ratio. There are two styles to display the image, “Pan&Scan”
(PS) and “Letter Box” (LB).
8 MONITOR TYPE
16:9 NORMAL (Wide television conversion):
Select this when the aspect ratio of your TV is
16:9 (wide TV).
16:9 AUTO (Wide television conversion):
Select this when the aspect ratio of your TV is
fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal
correctly when playing back a picture whose
aspect ratio is 4:3.
Pan&Scan
The right and left side of the image are
cut off. The image fills the screen.
Letter Box
4:3 LB (Letter Box conversion):
Black bands appear at the top and
bottom of the image. The image itself
appears in 16:9 aspect ratio.
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide
screen picture, the black bars appear on the
top and the bottom of the screen.
4:3 PS (Pan&Scan):
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide
screen picture, the black bars do not appear;
however, the left and right edges of the
pictures will not be shown on the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
EN
INITIAL SETTINGS (cont.)
On-screen Language Set (VCR deck)
Language
This VCR deck offers you the choice to view on-screen
messages in 3 different languages.
● Turn on the TV and select the VCR channel (or AV
mode).
A Turn on the unit.
● Slide the TV/VCR/DVD switch to the right.
Press POWER (1).
B Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Access the Main Menu screen.
Press SET UP MENU.
D Access the Initial Set screen.
Press rt to move the
highlight bar (arrow) to
“INITIAL SET”, then press OK
or e.
E Select the language.
Press rt to move the
highlight bar (arrow) to
“LANGUAGE”, then press
OK or e repeatedly until the
desired language is selected.
F Return to the normal screen.
Press SET UP MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
On-screen Language Set (DVD deck)
This DVD deck offers you the choice to view on-screen
messages in 3 different languages. You can change the
language setting manually as required.
A Turn on the unit.
Press POWER (1).
B Select the DVD deck.
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
C Access the DVD Set Up menu screen.
LANGUAGE
A Press SET UP MENU.
B Press w e to select
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
OFF
“
LANGUAGE”.
ON SCREEN LANGUAGE ENGLISH
SELECT
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
OK
D Select the mode.
Press rt to move H to “ON
SCREEN LANGUAGE”, then
press OK.
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
OFF
ON SCREEN LANGUAGE ENGLISH
SELECT
OK
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
E Select the mode setting.
Press rt to select the desired setting, then press OK.
F Return to the normal screen.
Press SET UP MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
EN
INITIAL SETTINGS (cont.)
Menu/Audio/Subtitle Language Set
(DVD deck only)
Some DVD discs contain the DVD menu display, audio,
subtitle in the multiple languages. With these discs, you
can set the default language as you like.
● The procedure shows how to set “MENU LANGUAGE”
on the DVD Set Up menu screen as an example.
A Turn on the unit.
Press POWER (1).
B Select the DVD deck.
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
C Access the DVD Set Up menu screen.
LANGUAGE
A Press SET UP MENU.
B Press w e to select
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
OFF
“
LANGUAGE”.
ON SCREEN LANGUAGE ENGLISH
SELECT
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
OK
D Select the mode.
Press rt to move H to
“MENU LANGUAGE”, then
press OK.
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
OFF
ON SCREEN LANGUAGE ENGLISH
SELECT
OK
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
E Select the mode setting.
Press rt to select the desired setting, then press OK.
● See “Language Code List” (੬ pg. 21).
F Return to the normal screen.
Press SET UP MENU.
NOTE:
When the selected language is not available on the disc, the
disc’s default menu language is played back.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
21
Language Code List
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
Afar
IK
Inupiak
RN
RO
RU
RW
SA
SD
SG
SH
SI
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Abkhazian
Afrikaans
Ameharic
Arabic
IN
Indonesian
Icelandic
Hebrew
IS
IW
JI
Yiddish
Javanese
Georgian
Kazakh
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
SK
BG
BH
BI
SL
Slovenian
Samoan
Shona
SM
SN
SO
SQ
SR
Bislama
Bengali, Bangla
Tibetan
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
Somali
Kirghiz
Albanian
Serbian
Siswati
Breton
Latin
Catalan
Corsican
Czech
Lingala
SS
ST
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
SU
SV
SW
TA
Welsh
Danish
Bhutani
Greek
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
OM
OR
PA
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
TE
Esperanto
Estonian
Basque
TG
TH
TI
Persian
TK
TL
Finnish
Fiji
TN
TO
TR
TS
Faroese
Frisian
Turkish
Tsonga
Tatar
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
TT
TW
UK
UR
UZ
VI
Twi
Ukrainian
Urdu
Uzbek
Hindi
Vietnamese
Volapuk
Wolof
HR
HU
HY
IA
Croatian
Hungarian
Armenian
Interlingua
Interlingue
PL
PS
PT
QU
RM
VO
WO
XH
YO
ZU
Xhosa
Yoruba
IE
Zulu
Download from Www.Somanuals.com. All Manuals Search And Download.
22
EN
INITIAL SETTINGS (cont.)
Perform clock setting only if the clock has not been set
correctly by the Plug&Play setting.
Clock Set
Preparations
● Turn on the TV and select the VCR channel (or AV
mode).
A Turn on the unit.
● Slide the TV/VCR/DVD switch to the right.
Press POWER (1).
B Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Access the Main Menu screen.
Press SET UP MENU.
D Access the Initial Set screen.
Press rt to move the
highlight bar (arrow) to
“INITIAL SET”, then press OK
or e.
E Access the Clock Set screen.
Press rt to move the
highlight bar (arrow) to
“CLOCK SET”, then press OK
or e.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
23
Semiauto Clock Set
E Complete the Semiauto Clock Set.
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually. First follow steps A to E in
“Preparations” (੬ pg. 22), then go to the following steps.
Press SET UP MENU to return to normal screen.
NOTE:
IMPORTANT
The time set previously will be erased when “AUTO CLOCK”,
“HOST CH”, “D.S.T.” or “TIME ZONE” setting is changed.
Turn off the unit after performing Semiauto Clock. “AUTO”
will appear on the front display panel while the clock is
being set. The current clock time will appear automatically
when the clock setting is complete.
A Set “AUTO CLOCK” to “ON”.
Press OK or e repeatedly to
move the highlight bar to
“AUTO CLOCK”, then press
rt so that “ON” is selected.
AUTO DAYLIGHT SAVING TIME
This function enables automatic adjustment of the unit’s
clock at the start and end of Daylight Saving Time.
With Auto DST activated, —
— on the first Sunday of April at 2:00 AM, the clock is
adjusted to 3:00 AM.
adjusted to 1:00 AM.
B Select the host channel.
Manual Clock Set
You can either select “AUTO” or enter a PBS channel
number.
First follow steps A to E in “Preparations” (੬ pg. 22), then go
Press OK or e to move the highlight bar to “HOST CH”,
then press rt repeatedly until “AUTO” or the desired
PBS channel number is selected.
to the following steps.
A Set time, date and year.
NOTE:
Press rt until the desired
time appears, then press OK
or e. Set the date and year in
the same way.
Some PBS channels do not transmit clock setting data.
C Select the D.S.T. mode.
● Holding rt changes the time
in 30-minute intervals, or
changes the date in 15-day
intervals.
press rt repeatedly until the desired setting is selected.
AUTO: Select if you want to adjust your VCR’s clock
automatically by the incoming signal from the
host channel. Be sure to select the correct time
zone manually in step D.
B Select D.S.T. mode.
Press OK or e to move the
highlight bar to “D.S.T.”, then
press rt to select the
desired setting.
ON:
Adjustment will be made by the built-in clock
itself.
OFF: Select when Daylight Saving Time does not apply
to you.
ON:
Adjustment will be
made by the built-in
clock itself.
D Select the time zone.
OFF: Select when Daylight
Saving Time does not
apply to you.
Press OK or e to move the highlight bar to “TIME
ZONE”, then press rt repeatedly until “AUTO” or the
desired time zone is selected. Each time you press the
button, the time zone changes as follows:
C Start clock.
{AUTO{ATLANTIC{EASTERN{CENTRAL{
MOUNTAIN{PACIFIC{ALASKA{HAWAII{
(back to the beginning)
Press SET UP MENU and normal screen appears.
To make corrections any time during the process
Press OK or e repeatedly until the item you want to change
blinks, then press rt.
NOTE:
If an incorrect time is displayed by the Plug & Play function, you
may be receiving the clock setting data of a PBS channel from an
adjacent time zone or from an incorrect PBS channel from a
cable TV system. If you selected “AUTO” for the host channel in
step B, be sure to select the correct time zone manually.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
EN
INITIAL SETTINGS (cont.)
Auto Channel Set
Tuner Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
● Turn on the TV and select the VCR channel (or AV
mode).
A Turn on the unit.
● Slide the TV/VCR/DVD switch to the right.
Press POWER (1).
B Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Access the Main Menu screen.
Press SET UP MENU.
D Access the Tuner Set screen.
Press rt to move the
highlight bar (arrow) to
“TUNER SET”, then press OK
or e.
E Perform Auto Channel Set.
Press rt to move the
highlight bar (arrow) to
“AUTO CHANNEL SET”, then
press OK or e. You can
automatically set the
receivable channels in your
area in the order of their
frequencies.
● When Auto Channel Set is
complete, “SCAN
COMPLETED” appears on the
TV screen.
● If the scan was unsuccessful,
“SCAN COMPLETED–NO
SIGNAL–” appears on screen.
Check the connections and start
again.
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be
displayed on the right side of “BAND” on the Tuner Set
screen.
F Return to the normal screen.
Press SET UP MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
25
Manual Channel Set
You can add the channels you want or delete the channels you
do not want manually.
A Turn on the unit.
Press POWER (1).
B Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Access the Main Menu screen.
Press SET UP MENU.
D Access the Tuner Set screen.
Press rt to move the highlight bar (arrow) to “TUNER
SET”, then press OK or e.
E Access the Manual Channel Set screen.
Press rt to move the
highlight bar (arrow) to
“MANUAL CHANNEL SET”,
then press OK or e.
F Add or skip the desired channels.
To add channels
A Press the number keys to
input a channel number you
want to add.
B Press OK or e to set to
“ADD”.
C Repeat A and B to add
other channels.
To skip channels
A Press rt or the number keys to select a channel
number you want to skip.
B Press OK or e to set to “SKIP”.
C Repeat A and B to skip other channels.
G Return to the normal screen.
Press SET UP MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
EN
OPERATIONS ON VCR DECK
A Load a cassette.
Basic Playback
Make sure the window side is up, the rear label side is
facing you and the arrow on the front of the cassette is
pointed toward the unit.
● Turn on the TV and select the VCR channel (or AV
mode).
● Do not apply too much pressure when inserting.
● If the record safety tab has been removed, playback begins
automatically. Although the DVD deck is selected, the VCR
deck is selected automatically if the DVD deck is in stop
mode.
● Slide the TV/VCR/DVD switch to the right.
● The unit’s power comes on automatically and the counter is
reset to 0:00:00.
B Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Find the program start point.
If the tape is advanced past the start point, press REW
(3). To go forward, press FF (5).
D Start playback.
Press PLAY (4).
E Stop playback.
Press STOP (8). Then press EJECT (x) on the VCR deck
to remove the cassette.
Usable cassettes
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T90
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
*
Compact VHS camcorder recordings can be played on
this unit. Simply place the recorded cassette into a VHS
Cassette Adapter and it can be used just like any full-sized
VHS cassette.
Clean the video heads using a dry cleaning
cassette — ECL-3F — when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
** This unit can record on regular VHS and Super VHS
cassettes. While only VHS signals can be recorded on
regular VHS cassettes1), both VHS and Super VHS signals
can be recorded and played back using Super VHS
cassettes.
1) By using the S-VHS ET function, it is possible to record
and play back with S-VHS picture quality on VHS
cassettes with this unit.
● “USE CLEANING CASSETTE” appears on the screen (only
with “SUPERIMPOSE” set to “ON”). (੬ pg. 75)
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or
humidity
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
27
Still Picture/Frame-By-Frame
Playback
Playback Features
1 Pause during playback.
● Turn on the TV and select the VCR channel (or AV
mode).
Press PAUSE (9).
● If there is vertical jitter, press CH +/– on the Remote to correct
● Slide the TV/VCR/DVD switch to the right.
the picture.
2 Activate frame-by-frame playback.
Press PAUSE (9) to advance a still picture.
Slow Motion
1 Pause during playback.
Press PAUSE (9).
2 Activate slow motion playback.
Press and hold PAUSE (9) for 2 seconds, then release.
Press PAUSE (9) and release again to return to still
picture.
● The speed changes for each direction by pressing REW (3)
and FF (5) repeatedly.
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press CH + or – on the Remote to eliminate the noises.
Variable Speed Search
During playback, press FF (5) for forward variable
speed search, or REW (3) for reverse variable speed
search.
● The speed changes for each direction by pressing REW (3)
and FF (5) repeatedly.
When pressing FF (5):
(SP): +5x{+7x
(EP): +11x{+21x
When pressing REW (3):
Once REW (3) is pressed, reverse search starts in –1x
normal playback speed. After this process, each press of REW
(3) changes the search speed between –5x and –7x in SP
mode, –11x and –21x in EP mode.
(SP): –1x]–5x{–7x
(EP): –1x]–11x{–21x
To resume normal playback, press PLAY (4).
ATTENTION
In the search, still, slow-motion or frame-by-frame playback
mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of colour.
● you cannot hear the sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
EN
OPERATIONS ON VCR DECK (cont.)
Index Search
x
Your unit automatically marks
index codes at the beginning of
each recording. This function gives
you quick access to any one of 9
index codes in either direction.
NOTE:
Before starting, make sure the unit
is in the Stop mode.
Activate Index Search.
Press INDEX (2) or INDEX (6). “INDEX –1” or
“INDEX 1” is displayed on the TV screen and search
begins in the corresponding direction.
● To access index codes 2 through 9, press INDEX (2) or
INDEX (6) repeatedly until the correct index number is
displayed.
Example:
To locate the beginning of B from the current position, press
INDEX (2) twice.
To locate the beginning of D from the current position, press
INDEX (6) once.
Current position
Index number
● When the specified index code is located, playback begins
automatically.
Instant ReView
Simply by pressing a single button, the unit power comes on,
rewinds, and begins playback of the last timer-recorded
program. If you have several programs recorded, you can easily
access any of them.
NOTE:
Before starting, make sure that the unit is off and that the Timer
mode is disengaged.
Activate Instant ReView.
Press
. The unit power comes on and the unit
searches for the index code indicating the start of the last
timer-recorded program. Once it’s found, playback begins
automatically.
● To watch the first of the 3 programs, press
three
Skip Search
times. The unit searches and begins playback automatically.
You can access a program as far as 9 index codes away from
the current tape position.
During playback, press SKIP SEARCH 1 to 6 times to skip
over unwanted sections.
Each press initiates a 30-second period of fast-motion
playback. Normal playback resumes automatically.
To resume normal playback during a Skip Search,
press PLAY (4).
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
29
Next Function Memory
Manual Tracking
The Next Function Memory “tells” the unit what to do after
rewinding. Before continuing, make sure the unit is in the Stop
mode.
Your unit is equipped with automatic tracking control. During
playback, you can override this and adjust the tracking manually
by pressing the CH buttons.
a- For Automatic Start Of Playback
Press REW (3), then press PLAY (4) within
2 seconds.
b- For Automatic Power Off
Press REW (3), then press POWER (1) within
2 seconds.
c- For Automatic Timer Standby
Press REW (3), then press TIMER within 2 seconds.
d- For Automatic Cassette Ejection After Tape Rewind
Press REW (3), then press EJECT (x) within 2
seconds.
1 Override automatic tracking.
During playback, press SP/EP on the Remote.
2 Adjust the tracking manually.
Press CH + or – on the Remote.
● Press SP/EP again to return to automatic tracking.
NOTE:
When a new tape is inserted, the unit enters the automatic
tracking mode automatically.
Repeat Playback
Your unit can automatically play back the whole tape 100 times
repeatedly.
1 Start playback.
Your unit is capable of recording three soundtracks (HI-FI L,
HI-FI R and NORM) and will play back the one you select.
During Playback
Press PLAY (4).
2 Activate Repeat Playback.
Pressing A.MONITOR changes the soundtrack as follows:
● You can also select the soundtrack on the Function Set screen.
(੬ pg. 73)
Press PLAY (4) and hold for over 5 seconds, then release.
● The Play indicator ($) on the front display panel blinks slowly.
● After playing back a tape 100 times, the unit stops
automatically.
TRACK
USE
3 Stop Repeat Playback.
On-Screen Display
Press STOP (8) at any time.
● Pressing PLAY (4), REW (3), FF (5) or PAUSE (9) also
stops Repeat Playback.
H I-F I
Hi-Fi sound is played back
Sound on the left Hi-Fi channel is
played back
H I-F I L
Sound on the right Hi-Fi channel is
played back
H I-F I R
NORM
Sound on the normal track is played
back
Both sounds on the Hi-Fi track and
normal track are mixed and played
back
NORM
H I-F I
NOTES:
● “HIFI” should normally be selected. In this mode, Hi-Fi stereo
tapes are played back in stereo, and the normal audio track is
played back automatically for tapes with only normal audio.
● “SUPERIMPOSE” must be set to “ON” or the on-screen
displays will not appear. (੬ pg. 75)
Download from Www.Somanuals.com. All Manuals Search And Download.
30
EN
OPERATIONS ON VCR DECK (cont.)
A Load a cassette.
Basic Recording
Insert a cassette with the record safety tab intact.
● The unit’s power comes on automatically and the counter is
reset to 0:00:00.
● Turn on the TV and select the VCR channel (or AV
mode).
B Select the VCR deck.
● Slide the TV/VCR/DVD switch to the right.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Choose a program.
Press CH +/– or the number keys to select the channel
you wish to record.
D Set the tape speed.
Press SP/EP. The current setting appears on the front
display panel or TV screen. Press SP/EP again to change
the setting while the tape speed is displayed on the TV
screen.
E Start recording.
Press and hold REC (7) and press PLAY (4) on the
Remote, or press REC (7) on the unit.
Video Calibration takes place at the beginning of both the
first SP and the first EP recording after inserting the cassette.
(੬ pg. 33)
F Pause/Resume recording.
Press PAUSE (9). Press PLAY (4) to resume recording.
● You can select channel during the Record Pause mode.
G Stop recording.
Press STOP (8). Then press EJECT (x) on the VCR deck
to remove the cassette.
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording or timer recording (੬ pg. 30, 31, 34), the
recording will resume automatically when power is restored
to the unit unless the unit’s memory backup has expired.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
31
Record One Program While Watching
Another
Recording Features
If your unit is connected to the TV via the AV connection,
press TV/VCR. The unit’s VCR indicator on the front
display panel and the TV broadcast being recorded
disappear.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
Once recording is in progress, all you need to do is to set
the channel controls on the TV for the station you wish to
view.
● The program selected with the TV’s channel controls appears
on the TV screen, while the one selected with the unit’s CH
buttons is recorded on the tape.
NOTE:
You can also use the DVD deck in the following cases. Before
use, be sure to turn on the unit and select the DVD deck.
● During recording
● During timer recording
● During timer standby mode
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the unit off after
recording is finished.
1 Start recording.
Press REC (7) on the unit.
2 Engage the ITR mode.
Press REC (7) again. “⅜” blinks and “0:30” appears on
the front display panel.
3 Set the recording duration.
If you want to record for more than 30 minutes, press
REC (7) to extend the time. Each press extends recording
time by 30 minutes.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette,
remove its safety tab. To record on it later, cover the hole
with adhesive tape.
NOTES:
● You can only perform ITR using the REC (7) button on the
unit’s front panel.
● Still picture playback stops automatically after 5 minutes to
protect the heads.
● When the end of the tape is reached during timer recording,
the unit stops and “⅜” and “$” blink on the front display
panel.
● When the end of the tape is reached during timer recording or
Instant Timer Recording, the unit is turned off and “⅜” and
“$” blink on the front display panel.
Record safety tab
● During Instant Timer Recording, any other timer programed
recording won’t start even if their start time has come. In such
a case, the timer programed recording starts (if the end time of
the timer programed recording is set after the end of Instant
Timer Recording) after the Instant Timer Recording finishes.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
EN
OPERATIONS ON VCR DECK (cont.)
Elapsed Recording Time Indication
1 Set the counter display.
Press DISPLAY until a counter reading appears on the
front display panel.
2 Reset the counter.
Press C.RESET before starting recording or playback.
● The counter is reset to “0:00:00” and shows the exact elapsed
time as the tape runs. You can check the exact time of a
recording or playback.
Tape Remaining Time
Press DISPLAY until the time remaining on the tape
appears.
● The front display panel shows the tape remaining time with
“z” displayed.
● By pressing the DISPLAY button, you can change display to
show the clock time, counter reading or tape remaining time.
NOTES:
● When you press DISPLAY, the on-screen display appears on
the TV screen for 5 seconds, then the displays other than the
counter disappears. To clear the counter display, press
DISPLAY.
● Depending on the type of tape being used, the tape remaining
time reading may not appear right away, or is not correct.
“– –:– –” may sometimes appear, or the display may blink on
occasion.
Second Audio Recording
This unit’s built-in MTS decoder enables reception of
Multichannel TV Sound broadcast. To record a SAP program
received, set “2ND AUDIO RECORD” to “ON”. (੬ pg. 76)
NOTE:
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about
5 seconds if the program is a stereo broadcast.
● The “SAP” indicator appears on the screen for about 5 seconds
if the program is a SAP broadcast.
● Both indicators appear when a stereo program is accompanied
by SAP sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
33
Recording
Active Video
Calibration
The unit assesses the quality
of the tape once you initiate
recording.
DURING VIDEO
CALIBRATION
● The unit spends approximately
7 seconds assessing the
condition of the tape, then
begins recording.
The Video Calibration checks the condition of the tape in
use during playback and recording, and compensates to
provide the highest-possible playback and recording
pictures. You can set “VIDEO CALIBRATION” to “ON” or
“OFF” to your preference. (੬ pg. 74)
NOTES:
● The Video Calibration works for
both SP and EP modes only
after a tape has been inserted
initiated. It does not work
during recording.
Playback
VIDEO CALIBRATION
COMPLETE
● The Video Calibration does not
work while Satellite Auto
Recording is in progress.
(੬ pg. 39)
● In the case of timer recordings,
the Video Calibration works
before recording is initiated.
● Once the cassette is ejected,
the Video Calibration data is
cancelled. The next time the
cassette is used for recording, Video Calibration is re-
performed.
● Pressing the unit’s REC (7) button while the Video Calibration
is displayed does not start Instant Timer Recording. (੬ pg. 31)
The unit assesses the quality
of the tape once you initiate
playback.
● The unit adjusts the playback
picture quality based on the
quality of the tape in use.
● Video Calibration is active
during automatic tracking. The
Video Calibration screen
appears blinking on the TV screen.
NOTES:
● When watching a tape recorded with “VIDEO CALIBRATION”
set to “ON”, it is recommended that you leave VIDEO
CALIBRATION on during playback as well.
● When watching a rental tape or one recorded on another VCR,
or when using this unit as the player for editing, set VIDEO
CALIBRATION to your preference. (੬ pg. 74)
● The Video Calibration only appears at the beginning of
automatic tracking. Even though it doesn’t appear after that,
the VIDEO CALIBRATION function is operative.
ATTENTION
Since the Video Calibration works before recording actually
starts, there is a delay of approximately 7 seconds after REC
(7) and PLAY (4) on the Remote are pressed, or REC (7) on
the unit is pressed. To make sure you record the desired
scene or program in its entirety, first perform the following
steps:
A Press and hold PAUSE (9) and press REC (7) to engage
the Record Pause mode.
tape and, after approximately 7 seconds, re-enters Record
Pause mode.
B Press PLAY (4) to start recording.
If you want to bypass the Video Calibration and begin
recording immediately, set “VIDEO CALIBRATION” to
“OFF”. (੬ pg. 74)
Download from Www.Somanuals.com. All Manuals Search And Download.
34
EN
OPERATIONS ON VCR DECK (cont.)
Example: To timer-record the program from 8:00 to
10:00 on 24th December, on channel 12.
Express Timer
Programing
A Select the VCR deck.
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the unit
Before performing Express Timer Programing:
● Make sure that the unit’s built-in clock is set properly.
● Insert a cassette with the safety tab in place. The unit will
come on automatically.
On the Remote
Press VCR so that the VCR indicator lights up.
● Turn on the TV and select the VCR channel (or AV mode).
● Slide the TV/VCR/DVD switch to the right.
B Access the Program screen.
starting out, “P1” appears.)
Press PROG.. (If you’re just
C Enter the program start time.
Press START +/– to enter the
time you want recording to
start.
● Press and hold START +/– to
move in 30-minute
increments, or press and
release repeatedly to move
1 minute at a time.
D Enter the program stop time.
Press STOP +/– to enter the time you want recording to
stop.
● Press and hold STOP +/– to move in 30-minute increments, or
press and release repeatedly to move 1 minute at a time.
E Enter the program date.
Press DATE +/–.
● The current date appears on the TV screen. The date you enter
appears in its place.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
35
NOTES:
F Enter the channel position.
● You can program this unit to timer-record as many as 8
programs. If you try to program the unit to record a ninth,
“PROGRAM FULL” appears on the TV screen. To record the
extra program, you must first cancel any unnecessary
programs. (੬ pg. 37)
● In case of a power failure after programing, the unit’s memory
backup keeps your selections for approximately 5 seconds.
date.
Press CH +/–.
G Set the tape speed.
Press SP/EP.
Cable Box or DBS Receiver Users
To timer-record a satellite broadcast using Express Timer
Programing:
A Perform steps A – I. In step F, enter “F-1” or “L-1” for
the channel position depending on the connector being
used.
B Set the DBS receiver to the appropriate channel before
the selected program begins.
C Leave the DBS receiver’s power on.
Press PROG. or OK. “PROGRAM COMPLETED” appears
on the TV screen for about 5 seconds, then the normal
screen appears. If “PROGRAM NOT COMPLETED
PROGRAM OVERLAP” appears on the TV screen, see
page 38.
● Repeat steps B – H for each additional program.
I Engage the unit’s timer mode.
Press TIMER. The unit turns off automatically and “#”
appears on the front display panel.
● To disengage the timer mode, press TIMER again.
To Timer-Record Weekly Or Daily Serials:
— anytime during steps C through G, press WEEKLY (number
key “9”) for weekly serials or DAILY (number key “8”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the TV screen. Pressing the button again makes the
corresponding indication disappear.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
EN
OPERATIONS ON VCR DECK (cont.)
Check, cancel and change programs
A Disengage the timer mode.
Press TIMER, then press POWER (1).
B Access the Program Check screen.
Press PROG. CHECK.
C Access the Program screen.
Press PROG. CHECK again
to check more information.
Each time you press
PROG. CHECK, the next
program’s information
appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
37
To cancel or change a program
D Cancel or change a program.
Press CANCEL to cancel a program. To change program
settings, press the appropriate button: START +/–,
STOP +/–, DATE +/–, CH +/–, DAILY (number key “8”),
WEEKLY (number key “9”) and/or SP/EP.
E Return to the normal screen.
Press PROG. CHECK as many times as necessary. If there
are still some programs remaining, go on to step F.
F Return to the timer mode.
Press TIMER.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
EN
OPERATIONS ON VCR DECK (cont.)
When programs overlap each other
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program
you have just made.
The Program Check screen appears and conflicting programs
will start blinking.
Example: Program 1 (you have just made) and Program 4
overlap each other.
A Confirm the overlapping programs.
Overlapping programs blink on the TV screen.
B Select the program to modify.
Press rt, then press OK or e.
● You can only select one of the overlapping programs.
NOTE:
If you do not mind this overlap, press PROG. to finish the timer
program setting. The program with the lower program number
will be recorded and the other one will not be recorded
correctly. If no changes are made for approximately 1 minute,
the unit will return to the normal screen.
C Cancel or change program setting.
To cancel a program, press CANCEL when the Program
screen you do not want is shown. “PROGRAM
COMPLETED” appears on the TV screen for about
5 seconds, then the normal screen appears.
ATTENTION
If there is a conflict in the timer schedule and one
program overlaps with another, only the parts shown
below in gray will be recorded.
To change a program, press the appropriate button:
START +/–, STOP +/–, DATE +/–, CH +/–, DAILY
(number key “8”), WEEKLY (number key “9”) and/or SP/
EP when the Program screen on which you want to make
changes is shown, then press OK. “PROGRAM
COMPLETED” appears on the TV screen for about
5 seconds, then the normal screen appears.
Pattern 1: The program with the lower program number
will be recorded.
Program 1
Program 2
CH10
CH40
Not recorded
NOTE:
If the overlap is not yet solved, or another overlap occurs with
the timer program setting after making the last correction on a
program, the conflicting programs will be shown on the Program
Check screen again. Repeat the above steps again until the
overlap is solved.
Pattern 2: The program starting earlier will be recorded.
Program 1
Program 2
CH10
CH40
Not recorded
Pattern 3: The program starting earlier will be recorded,
followed by the remaining portion of the other
program.
Program 1
CH10
Program 2
CH40
Not recorded
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
39
ATTENTION
● Be sure not to turn on the DBS receiver before the program
is executed; otherwise, the unit will start recording when
the DBS receiver’s power is turned on.
Satellite Auto
Recording
● If you have connected another appliance other than a DBS
receiver to the AUDIO/VIDEO INPUT (L-1) connectors, be
sure not to engage the Satellite Auto Recording mode;
otherwise, the unit will start recording when the connected
appliance’s power is turned on.
● Satellite Auto Recording and timer-recording cannot be
done at the same time.
This function allows you to automatically record a
satellite program which is timer-programed on your
external DBS receiver. Connect a DBS receiver to the
unit’s AUDIO/VIDEO INPUT (L-1) connectors and
program the timer on the DBS receiver. The unit starts or
stops recording by the signals input from the DBS
receiver. After recording, the unit’s power shuts off
automatically.
Before performing the following steps:
● Make sure the DBS receiver is connected to the unit’s
AUDIO/VIDEO INPUT (L-1) connectors.
● You can also connect the cable box if it has a timer.
● Program the timer on the DBS receiver.
● Insert a cassette with the safety tab in place.
● Slide the TV/VCR/DVD switch to the right.
A Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
“N” indicator
On the Remote
Press VCR so that the VCR indicator lights up.
B Set the tape speed.
Press SP/EP.
C Engage the Satellite Auto Recording mode.
Press and hold REC LINK for about 2 seconds. The “N”
and “#” indicators light up and the unit turns off
automatically.
NOTES:
● To disengage the Satellite Auto Recording mode, press REC LINK. The “N” indicator goes off.
● If the unit’s power is off, it is not possible to engage the Satellite Auto Recording mode.
● In step C, if the “N” indicator does not light but instead blinks quickly even though your DBS receiver’s power is off, Satellite Auto
Recording will not work properly with that DBS receiver*. If this is the case, perform “Express Timer Programing” (੬ pg. 34) to
timer-record a satellite program.
* Some DBS receivers output signals even if the power is off. Satellite Auto Recording is not possible with those DBS receivers.
● The “N” indicator blinks while Satellite Auto Recording is in progress.
● For timer programing of the DBS receiver, refer to the instruction manual of the DBS receiver.
● Satellite Auto Recording is not possible if your DBS receiver does not have a timer.
● Pressing the unit’s POWER (1) button while Satellite Auto Recording is in progress turns off the unit’s power and disengages the
Satellite Auto Recording mode.
● If there are more than one satellite programs you wish to record with Satellite Auto Recording, it is not possible to set different tape
speeds for each program.
● Depending on the type of DBS receiver, the unit may not record a slight portion of the beginning of the program or may record
slightly longer than the actual length of the program.
● If you engage the Satellite Auto Recording mode when the DBS receiver’s power is on, the unit will not start Satellite Auto Recording
even though the “N” and “#” indicators blink. When the DBS receiver shuts off once and is turned back on again, the unit starts
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
● You can also record a program from your cable system in the same way if the system has a timer.
40
EN
OPERATIONS ON DVD DECK
To play back a MP3/WMA/JPEG disc, see pages 60 – 65.
Basic Playback
A Load the disc.
A Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
● The unit’s power comes on automatically.
B Place the disc in the disc tray.
● For details, refer to “Placing a Disc” (੬ pg. 7).
C Press OPEN/CLOSE (x) on the DVD deck to close the
disc tray.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
● Pressing PLAY (4) also close the disc tray.
● Playback begins automatically if the auto-playback DVD disc
is loaded. Although the VCR deck is selected, the DVD deck is
selected automatically if the VCR deck is in stop mode.
B Select the DVD deck.
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
C Start playback.
Press PLAY (4).
Example: DVD VIDEO
Title number
Chapter
number
Elapsed time
● It may take a few seconds to start playback.
● If you load a DVD disc whose region code does not match the
menu display may appear on the TV screen after starting
playback. In this case, select an item which you want to play
back from the menu. Otherwise, the playback cannot go
forward. Refer to “Locating a desired scene using the menu of
the Video CD with PBC” (੬ pg. 41) or “Locating a desired
scene using the DVD menu” (੬ pg. 41).
D Pause playback.
Press PAUSE (9).
● To resume normal playback, press PLAY (4).
Press STOP (8). Press OPEN/CLOSE (x) on the DVD
deck to open the disc tray, then remove the disc.
● Pressing PLAY (4) resume playback from the position where
you stop playback. For details, see “Resume Function” on
page 43.
ATTENTION
● You can not use the DVD deck when the VCR deck is in
the Satellite Auto Recording standby and recording mode.
● You can use the DVD deck when the VCR deck is in the
timer standby mode.
NOTE:
When you press OPEN/CLOSE (x) while the unit is turned off,
the unit’s power comes on and the disc tray opens automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
41
Locating a desired scene using the
DVD menu
Playback Features
● Turn on the TV and select the VCR channel (or AV
mode).
DVD VIDEO discs may have two types of the menus; top menu
and disc menu.
● Slide the TV/VCR/DVD switch to the right.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Playback Control (PBC) Function
— Locating a desired scene using the
menu of the Video CD with PBC
Disc menu
DVD discs have the disc menu to select subtitle and audio
language etc. for each title.
Press MENU to access the disc menu.
1 Access the DVD menu.
Some Video CD discs supports the PBC function. PBC is an
abbreviation of “PlayBack Control.” A Video CD disc recorded
with PBC has its own menus, such as a list of the songs of the
disc. You can locate a specific scene by using the menu.
Press TOP MENU or MENU.
1 Access the PBC menu.
In stop mode
Press PLAY (4).
● Depending on a disc, PBC
menu may automatically
appear on the TV screen by
simply loading a disc on the
unit.
Example:
2 Start playback.
Press rt w e to select a desired item, then press OK.
● It may be possible to select the desired item using the number
keys depending on the disc.
During playback
Press RETURN.
● “PBC” appears on the front
display panel.
NOTES:
● When “X” appears on the TV screen in step 1, the disc does
not have a top menu or disc menu.
● Top menu or disc menu may not appear depending on the
discs even if it is recorded in DVD VIDEO format and
finalized. In that case, press STOP (8) to display the total
number of titles on a disc, then press the appropriate number
keys to select the desired title.
2 Start playback.
Press the appropriate number keys.
● The unit starts playback of the selected item.
● When “NEXT” or “PREVIOUS” appears on the TV screen:
Pressing SKIP (6) advances to the next page.
Pressing SKIP (2) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the
disc.
NOTES:
● If you want to playback a PBC-compatible Video CD disc
without activating the PBC function, start playback by using
the number keys instead of the PLAY (4) button.
● To activate the PBC function when a PBC-compatible Video
CD disc is being played back without the PBC function, press
TOP MENU or MENU, or press STOP (8) (press twice when
“RESUME” is set to “ON”) then press PLAY (4).
Download from Www.Somanuals.com. All Manuals Search And Download.
42
EN
OPERATIONS ON DVD DECK (cont.)
Locating the start point of the item or
skip the item
Press SKIP (2) or SKIP (6) during playback.
Example:
To locate the beginning of item B from the current position, press
SKIP (2) twice.
To locate the beginning of item D from the current position,
press SKIP (6) once.
Current position
The number you press the
button
● When the specified item is located, playback begins
automatically.
Variable Speed Search
During playback, press FF (5) for forward variable
speed search, or REW (3) for reverse variable speed
search.
● The more times you press, the faster the playback picture
moves.
● To resume normal playback, press PLAY (4).
OR
During playback, press and hold SKIP (6) for forward
variable speed search, or press and hold SKIP (2) for
reverse variable speed search.
● While you press and hold the button, the image is played back
at 5x speed.
● To resume normal playback, release SKIP (2) or SKIP (6).
NOTES:
● Actual speed may be different from that displayed on the TV
screen depending on the discs.
● Playback sound is not heard in any variable speed search
mode other than in 1.5x speed search mode.
● During 1.5x speed search of a DVD VIDEO disc, you can hear
the played back audio converted into Linear PCM format in
stereo. In such a case, the pitch and sound quality may change
depending on the disc.
● In case of DVD VIDEO discs formatted in DTS format, SVCD
or Audio CD discs, playback sound is not heard during 1.5x
speed search.
● When switching to 1.5x speed search during variable speed
Search, first press PLAY (4) to return to normal playback, then
press FF (5).
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
43
2 Resume playback.
Still Picture/Frame-By-Frame
Playback
Press PLAY (4). The unit start playback from the resume
point.
● “RESUME PLAY” appears on the front display panel.
1 Pause during playback.
Press PAUSE (9).
NOTES:
● Resume Function does not work on the Audio CD. It also may
not work depending on the discs.
2 Activate frame-by-frame playback.
● If you stop the playback of a disc for which an resume point
has already been memorized, the memory will be updated
with the new resume point.
Press PAUSE (9) to advance a still picture.
● To resume normal playback, press PLAY (4).
● After the unit has memorized the resume point for 30 discs,
remembering a new resume point will cause the unit to delete
the oldest memorized point. Stopping playback of a disc for
which a resume point is already stored may change the order
in which the points are stored. This may potentially change the
order in which points are deleted.
Slow Motion
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not works for some Video CD or SVCD.
During playback, press PAUSE (9), then press REW (3)
for reverse slow motion playback, or FF (5) for forward
slow motion playback.
● Each press of FF (5) changes the playback speed as follows:
1/32]1/16]1/4]1/2
Zooming
● Each press of REW (3) changes the playback speed as
follows (only for DVD VIDEO discs):
–1/32]–1/16]–1/4]–1/2
● To resume normal playback, press PLAY (4).
Press ZOOM during playback or while paused.
● Each press of ZOOM changes the magnification as follows:
1.8x]4x]8x]16x]32x]64x
NOTES:
● Reverse slow motion playback is possible only with the DVD
VIDEO discs.
● When a 16:9 aspect picture source is displayed on a 4:3
aspect TV (conventional TV) in Letter Box conversion mode,
the margins in black shown on top and bottom of the TV
screen will be cropped by selecting 1.8x magnification. In
such a case, note that both left and right side parts of the
picture will also be cropped.
● This function may not works for some Video CD or SVCD.
Resume Function
● While zoomed, the picture may look coarse or distorted.
Current magnification
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set “RESUME” to “ON” or “DISC RESUME”.
(੬ pg. 81)
1 Memorize the resume point.
Press STOP (8) during playback.
● “RESUME STOP” appears on the front display panel.
Zoomed-in area
● The unit enters Resume Stop mode and memorise the position
where you stop playback as the resume point.
● The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected if
“RESUME” is set to “DISC RESUME”. (੬ pg. 81)
● To clear the resume point:
Press rt w e to move the zoomed-in scene.
When “RESUME” is set to “ON”:
• Press STOP (8) in stop mode.
• Press POWER (1) to turn off the unit.
• Eject the disc.
When “RESUME” is set to “DISC RESUME”:
• Set “RESUME” to “OFF”. (੬ pg. 81)
• Press STOP (8) in stop mode.
● To resume normal playback, press OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
EN
OPERATIONS ON DVD DECK (cont.)
● Each time you press w e, the setting changes as follows:
NONE]ACTION]DRAMA]THEATER](Back to the
beginning)
NONE:
ACTION:
No effect
Suitable for action movies and sports
programs in which sounds dynamically
move.
DRAMA:
Provides the natural and warm sound. You
can enjoy movies in a relaxed mood.
You can enjoy sound effects like in a major
theater.
THEATER:
● The selection menu disappears automatically if you do not
change the selection for 10 seconds.
3 Select the effect level.
Press rt to select the desired effect level. (level 1 to 5)
● To resume normal playback, press 3D-PHONIC.
NOTES:
● The 3D Phonic function works correctly only when playing
back a DVD VIDEO disc recorded in the Dolby Digital format.
With other sources, you cannot get any effect if you activate
3D Phonic function.
● When playing back a DVD VIDEO disc recorded with the
Dolby Digital that does not contain the rear signal, you cannot
get a correct 3D Phonic sound even if you activate 3D Phonic
function.
● The 3D Phonic function does not affect the Dolby Digital
bitstream signal from the DIGITAL AUDIO OUT connector.
● When 3D Phonic function is activated, Analog Down Mix and
D. Range Control functions are disabled. (੬ pg. 80)
3D Phonic
3D Phonic function allows you to get a simulated surround
effect from your stereo system. You can enjoy the vertical
surround sound with your 2-channel stereo system.
1 Access the selection menu.
Press 3D-PHONIC during playback.
● The current setting appears on the right bottom corner of the
TV screen.
2 Select the mode.
Press w e repeatedly, then
press OK.
Selected mode
Effect level
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
45
4 Select the parameter.
VFP function
— Adjusting the picture quality
Press rt repeatedly to select a parameter you want to
adjust, then press OK.
● Adjust gradually and confirm picture appearance results are as
preferred.
GAMMA
Controls brightness of neutral tints while
maintaining brightness of dark and bright
portions.
(–4 to +4):
The VFP (Video Fine Processor) function enables you to adjust
the picture character according to the type of programing,
picture tone or personal preference.
BRIGHTNESS Controls screen brightness.
(–16 to +16):
NOTE:
Before you start operation;
CONTRAST
(–16 to +16):
Controls screen contrast.
The VFP setting screen disappears if no operations are done for
more than about 10 seconds. If the setting screen disappears
before you finish, start from step 1 again.
SATURATION Controls screen color depth.
(–16 to +16):
1 Access the VFP setting menu.
TINT
Controls screen tint.
(–16 to +16):
Press DVD PICTURE during
NORMAL
playback.
SHARPNESS Controls screen sharpness.
+
+
+
+
+
+
+
GAMMA
0
0
0
0
0
3
0
● The current setting appears on
BRIGHTNESS
CONTRAST
SATURATION
TINT
(+0 to +3):
the TV screen.
Y DELAY
(–2 to +2):
Controls screen color gap.
SHARPNESS
Y DELAY
● VFP menu disappears and the following pop-up window
appears on the TV screen.
2 Select the VFP mode.
Press w e repeatedly.
● Each time you press w e, the VFP mode changes as follows:
NORMAL]CINEMA]USER 1]USER 2](Back to the
beginning)
+
GAMMA
0
+
GAMMA
0
NORMAL:
CINEMA:
Select this normally.
Suitable for movie.
Press rt repeatedly to change the setting, then press
USER 1/
USER 2:
You can adjust parameters that affect picture
appearance and store settings. Go to step 3.
OK.
● The current VFP settings appear again.
NOTE:
6 Adjust the other parameters.
You cannot adjust the parameters of “NORMAL” and “CINEMA”.
Repeat steps 4 and 5 to adjust other parameters.
To adjust picture appearance manually
To return to the normal screen
Press DVD PICTURE.
3 Access USER menu.
To activate your setting
Press w e repeatedly to
Press DVD PICTURE, then press w e repeatedly to select
“USER 1” or “USER 2” that you have changed the
parameters.
USER 1
select “USER 1” or “USER 2”.
+
+
+
+
+
+
+
GAMMA
0
0
0
0
0
3
0
BRIGHTNESS
CONTRAST
SATURATION
TINT
SHARPNESS
Y DELAY
Download from Www.Somanuals.com. All Manuals Search And Download.
46
EN
OPERATIONS ON DVD DECK (cont.)
How to Access the on-screen bar
Press PLAY SETUP twice whenever a disc is loaded.
Example: During DVD VIDEO playback
Using the on-
screen bar
Example: During Video CD playback
You can check disc information while the disc is loaded and you
can use some functions using the on-screen bar. The on-screen
bar allows you the various playback operations.
Contents of the on-screen bar during playback
DVD
Video CD
A Disc type
B Current transfer rate (Megabits per second)
C Current title (for DVD)
D Current chapter number (for DVD) or track number
(for other type of discs)
E Time information (੬ pg. 47)
F Playback status
: appears during playback.
/
/
: appears during fast forward/reverse.
: appears during playback in forward slow-
motion/reverse slow-motion.
: appears when paused.
: appears when stopped.
G Select this to change time information. (See 5 in the
H Select this for Repeat Playback. (੬ pg. 48)
(੬ pg. 54, 55)
L Select this to change subtitle language. (੬ pg. 52)
M Select this to change view angle. (੬ pg. 53)
N Select this for Program Playback. (੬ pg. 51)
O Select this for Random Playback. (੬ pg. 51)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
47
Basic operation on the on-screen bar
Example: When selecting the Repeat mode of DVD
During playback or while stopped
Change the time information
You can change the time information in the on-screen bar on the
TV screen and the front display panel of the unit.
A Access the on-screen bar.
During playback or while stopped
Press PLAY SETUP twice. The on-screen bar appears on
the TV screen.
● The currently selected item is highlighted.
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
the TV screen.
B Select menu item.
● Each time you press OK, the time information changes as
follows;
B Select menu item.
pop-up window appears under the selected item.
● The current setting appears.
Press w e to move H to
, then press OK.
Press w e to move H to
, then press OK. The
Example: During DVD playback
(Back to the beginning)
TIME:
Elapsed playing time of current chapter/track
Remaining time of current chapter/track
Elapsed time of title/disc
REM:
C Select the option.
TOTAL:
T. REM:
Remaining time of title/disc
Press rt to select the desired option, then press OK.
● Each time you press rt, the options change.
To clear the on-screen bar
Press PLAY SETUP.
To clear the on-screen bar
Press PLAY SETUP.
NOTES:
NOTE:
● While playing a Video CD, Audio CD or SVCD, the hour digit
indication does not appear.
See the corresponding pages for details on each function.
● While a DVD is stopped, “– – : – –” appears in the time
information display.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
EN
OPERATIONS ON DVD DECK (cont.)
C Select the repeat mode.
Press rt repeatedly to select the Repeat mode, then
press OK.
● The mode changes as follows:
DVD VIDEO
CHAPTER]TITLE]A-B]OFF](Back to the beginning)
CHAPTER:
TITLE:
A-B:
The current chapter is played back
repeatedly.
The current title is played back
repeatedly.
The desired part is played back
repeatedly. (੬ pg. 49)
Each title and chapter is played
back once.
OFF:
Video CD/SVCD/CD
TRACK]ALL]A-B]OFF](Back to the beginning)
The current track is played back
repeatedly.
TRACK:
ALL:
All tracks are played back
repeatedly.
A-B:
The desired part is played back
repeatedly. (੬ pg. 49)
Each track is played back once.
OFF:
● “A-B” cannot be selected while stopped.
To clear the on-screen bar
Press PLAY SETUP.
To cancel Repeat Playback
Repeat from step A, select “OFF” in step C, then press
OK.
When using the REPEAT button:
Repeat Playback
A Access the repeat mode.
Press REPEAT during playback of the item you want to
repeat.
You can repeat playback as you like according to the type of
disc.
● Repeat mode is displayed on the TV.
DVD VIDEO:
Audio CD:
during playback
during playback or in stop mode
Video CD/SVCD: in stop mode or during playback with PBC
disactivated
B Select the repeat mode.
Press REPEAT repeatedly to select the desired repeat
mode, then press OK.
When using the on-screen bar
● To stop Repeat Playback, press STOP (8).
● To cancel Repeat Playback, press REPEAT repeatedly until
“OFF” appears on the TV screen, then press OK.
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
NOTES:
the TV screen.
● Repeat Playback is not possible with a Video CD and SVCD
with PBC function.
● Repeat Playback may not work properly depending on the
type of disc being used.
● You cannot select A-B Repeat Playback by pressing REPEAT.
B Select menu item.
● The following pop-up window appears under the selected
item.
Press w e to move H to
, then press OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
49
A-B Repeat Playback
Time Search
You can repeat the desired part.
You can play back a disc from the desired point by specifying the
elapsed time from the beginning of the current title (for DVD
VIDEO) or the disc (for Audio CD/Video CD) using the Time
Search.
When a PBC-compatible Video CD is played back, be sure to
inactivate PBC function before you perform Time search by
pressing the number keys instead of the PLAY (4) button when
you start playback.
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
the TV screen.
B Select menu item.
● The following pop-up window appears under the selected
item.
A Access the on-screen bar.
the TV screen.
Press w e to move H to
, then press OK.
Press PLAY SETUP twice. The on-screen bar appears on
B Select menu item.
● The following pop-up window appears under the selected
item.
Press w e to move H to
, then press OK.
C Select the repeat mode.
Press rt repeatedly to select “A-B”.
D Select the start point.
C Select the time.
Press OK at the beginning of the part you want to repeat
(point A).
Press the number keys (0-9) to enter the time, then press
OK.
● The following display appears in the on-screen bar.
Example:
To play back from a point 2 (hours): 34 (minutes): 08 (seconds)
elapsed
TIME _ : _ _ : _ _
TIME 2 : 3 _ : _ _
TIME 2 : 3 4 : 0 _
TIME 2 : _ _ : _ _
Press 2
Press 3
TIME 2 : 3 4 : _ _
Press 0
Press OK at the end of the part you want to repeat (point B).
● A-B Repeat Playback starts. The selected part of the disc
(between point A and B) is played repeatedly.
Press 4
Press 8
TIME 2 :3 4 :0 8
To cancel A-B Repeat Playback
Repeat from step A, select “OFF” in step C, then press
OK.
If you have specified a wrong selection,
● You can also cancel Repeat Playback by pressing SKIP (2)
or SKIP (6).
Press w repeatedly until the wrong number is erased,
then press number keys to enter the correct numbers.
● The unit starts playback from the specified time.
To clear the on-screen bar
Press PLAY SETUP.
To clear the on-screen bar
Press PLAY SETUP.
NOTES:
● A-B Repeat Playback may not work properly depending on the
type of disc being used.
NOTES:
● When “X” is displayed on the TV screen in step C, you have
selected a point that excesses the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and
it is no possible to use the Time Search function. In such a
case, “X” is displayed on the TV screen as well.
● Time Search does not work while you play back the Video CD
or SVCD with the PBC Function.
● The subtitles recorded around A-B point may not appear.
● The end of the item will be set as “B” point if the end of the
item reached before you set the “B” point.
● When playing back a DVD, A-B Repeat Playback is possible
only within the same title.
● “A-B” cannot be selected during Program and Random
Playback.
● “A-B” cannot be selected while stopped.
Reactivate the Playback Control (PBC) Function
You can reactivate the PBC function when you play back a PBC-
compatible Video CD disc without PBC function.
● Press TOP MENU during playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
50
EN
OPERATIONS ON DVD DECK (cont.)
Chapter Search
You can start playback the desired chapter using the on-screen
bar.
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
the TV screen.
B Select menu item.
● The following pop-up window appears under the selected
item.
Press w e to move H to
, then press OK.
C Select the chapter.
Press the number keys (0-10) to enter the desired chapter
number, then press OK.
● The unit starts playback from the selected chapter.
Examples:
To select track 5, press the number key “5”.
To select track 15, press the number key “1” and “5”.
To select track 25, press number key “2” and “5”.
● It is not possible to use the number key “+10”.
If you have specified a wrong selection
Enter the appropriate number keys again.
To clear the on-screen bar
Press PLAY SETUP.
NOTES:
● When “X” is displayed on the TV screen in step C, the
chapter you have selected is not contained in the disc, or
chapter search does not work on the disc.
● Chapter Search starts automatically when you select the
desired chapter in step C depending on the disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
51
Program Playback
Random Playback
You can play back up to 99 tracks in the desired order.
You can play back all the tracks on the disc in random order.
A Access the on-screen bar.
A Access the on-screen bar.
Press PLAY SETUP twice in stop mode.
Press PLAY SETUP twice in stop mode.
B Select the menu item.
B Select the menu item.
Press w e to move H to
, then press OK.
Press w e to move H to
, then press OK.
● The program table appears under the on-screen bar.
● Playback starts in random order.
● To stop and quit Random Playback, press STOP (8).
● To cancel Random playback, repeat step B during Random
Playback. Normal playback resumes at the current point.
C Select the tracks in the desired order.
Press the appropriate
To clear the on-screen bar
Press PLAY SETUP.
number keys to select the
Program time
tracks.
NOTES:
● The same track will not be played back more than once during
Random Playback.
● Random playback is canceled when all the tracks have been
played back.
Examples:
● To select track 5, press the number key “5”.
● To select track 15, press the number key “+10” and “5”.
● To select track 25, press number key “+10” twice, then
“5”.
If you have specified a wrong selection
Press STOP (8). The last selection programed is erased.
D Start playback.
Press PLAY (4). Playback starts in the selected order.
● When all of the programed tracks have been played back,
Program Playback stops, but the programed information
remains.
● To stop Program Playback, press STOP (8).
● To clear all the programed tracks, press STOP (8) to stop
playback and press PLAY SETUP to clear the program table,
then press STOP (8) again.
● During Program Playback, pressing SKIP (6) skip to the next
selection of the program. Pressing SKIP (2) returns to the
beginning of the current selection.
To clear the program table
Press PLAY SETUP.
NOTE:
Program Playback is not possible depending on the type of disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
EN
OPERATIONS ON DVD DECK (cont.)
C Select the subtitle language.
Press rt repeatedly to select the desired subtitle
language, then press OK.
● Each time you press the button, the subtitle language changes.
Press PLAY SETUP.
NOTES:
● For DVD VIDEO
Some subtitle languages are abbreviated in the pop-up
window. See “Language Code List” (੬ pg. 21).
● For SVCD
SVCD can contain up to four subtitles. Pressing SUB TITLE
changes the subtitles regardless of whether the subtitles are
recorded or not. (Subtitles will not change if no subtitle is
recorded.)
● When “X” appears on the TV screen in step C, subtitle
language is not recorded.
When using the SUB TITLE button:
A Access the menu.
Press SUB TITLE.
● The following pop-up window appears on the TV screen.
Example (DVD):“ENGLISH” is selected out of 3 subtitle
languages recorded.
B Select the subtitle language.
Subtitle Selection
Press rt or SUB TITLE repeatedly to select the desired
subtitle language, then press OK.
● Each time you press the button, the subtitle language changes.
● The pop-up window disappears if no operation is done for
about 5 seconds.
You can select subtitle language.
● During playback
NOTE:
When “X” appears on the TV screen in step B, subtitle language
When using the on-screen bar
is not recorded.
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
the TV screen.
B Select menu item.
● The following pop-up window appears under the selected
item.
Press w e to move H to
, then press OK.
Example (DVD):“ENGLISH” is selected out of 3 subtitle
languages recorded.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
53
When using the ANGLE button:
Angle Selection
A Access the menu.
Press ANGLE.
You can enjoy a variety of scene angles if the DVD VIDEO disc
contains “multi-angle” parts, where multiple cameras were used
to shoot the same scene from different angles.
● The following pop-up window appears on the TV screen.
Example:The first view angle is selected out of 3 view angles
recorded.
If the disc contains “multi-angle” parts, “
” appears on the TV
screen at the beginning of the “multi-angle” part when “ON
SCREEN GUIDE” is set to “ON”.
● During playback
When using the on-screen bar
A Access the on-screen bar.
the TV screen.
B Select the view angle.
Press PLAY SETUP twice. The on-screen bar appears on
Press rt or ANGLE repeatedly to select the desired
view angle, then press OK.
B Select menu item.
● The following pop-up window appears under the selected
item.
● Each time you press the button, the angle of the scene
changes.
● The pop-up window disappears if no operation is done for
about 5 seconds.
Press w e to move H to
, then press OK.
Example:
Example: The first view angle is selected out of 3 view angles
recorded.
1/3]2/3]3/3](Back to the beginning)
1
1
1
1
C Select the view angle.
Press rt repeatedly to select the desired view angle,
then press OK.
● Each time you press the button, the angle of the scene
changes.
To clear the on-screen bar
Press PLAY SETUP.
NOTE:
When “X” appears on the TV screen in step C, the current
scene is not recorded from multiple angles.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
EN
OPERATIONS ON DVD DECK (cont.)
B Select menu item.
● The following pop-up window appears under the selected
item.
Press w e to move H to
, then press OK.
Example:“ENGLISH” is selected out of 4 audio languages
recorded.
C Select the audio language.
Press rt repeatedly to select the desired audio
language, then press OK.
● Each time you press the button, the audio language changes.
To clear the on-screen bar
Press PLAY SETUP.
NOTES:
● Some audio languages are abbreviated in the pop-up window.
See “Language Code List” (੬ pg. 21)
● If “X” appears on the TV, the current scene does not contain
plural audio languages.
When using the A.MONITOR button:
A Access the menu.
Press A.MONITOR.
● The following pop-up window appears on the TV screen.
Example: “ENGLISH” is selected out of 3 audio languages
recorded.
Audio Language Selection
Some DVD discs contain the multiple audio.
You can select the audio language of movies (DVD VIDEO).
● During playback
B Select the audio language.
Press rt or A.MONITOR repeatedly to select the
desired audio language, then press OK.
● The pop-up window disappears if no operation is done for
about 5 seconds.
When using the on-screen bar
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
NOTE:
the TV screen.
Some audio languages are abbreviated in the pop-up window.
See “Language Code List” (੬ pg. 21).
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
55
When using the A.MONITOR button:
Audio Channel Selection
A Access the menu.
● The following pop-up window appears on the TV screen.
Example:“ST” (stereo) is selected out of 3 audio channels
recorded.
Press A.MONITOR.
When you play certain karaoke (DVD/Video CD/SVCD), you can
enjoy karaoke by selecting the audio channel to play.
● The sound of each audio channel depends on the contents of
the disc.
● During playback
When using the on-screen bar
A Access the on-screen bar.
Press PLAY SETUP twice. The on-screen bar appears on
the TV screen.
B Select the audio channel.
Press rt or A.MONITOR repeatedly to select the
desired audio channel, then press OK.
B Select menu item.
● Each time you press the button, the audio channel changes.
● The pop-up window disappears if no operation is done for
about 5 seconds.
Press w e to move H to
, then press OK.
● The following pop-up window appears under the selected
item.
Example: “ST” (stereo) is selected.
For Video CD
ST]L]R](Back to the beginning)
To listen to normal stereo playback.
To listen to L (left) audio channel only.
To listen to R (right) audio channel only.
ST:
L:
R:
C Select the audio channel.
For SVCD
Press rt repeatedly to select the desired audio channel,
then press OK.
ST 1]ST 2]L 1]R 1]L 2]R 2](Back to the beginning)
To listen to normal stereo playback of ST 1 or
ST 2 channel.
● Each time you press the button, the audio channel changes.
ST 1/ST 2:
To clear the on-screen bar
Press PLAY SETUP.
To listen to the L (left) 1 or 2 audio channel.
To listen to the R (right) 1 or 2 audio channel.
L 1/L 2:
R 1/R 2:
Download from Www.Somanuals.com. All Manuals Search And Download.
56
EN
OPERATIONS ON DVD DECK (cont.)
C Access the DVD Set Up menu.
B Press w e to select “ OTHERS”.
Parental Lock
A Press SET UP MENU.
This function restricts playback of DVD VIDEO discs which
contain violent (and other) scenes according to the level set by
the user. For example, if a movie which includes violent scenes
supports the parental lock feature, such scenes which you do not
want to let children view can be cut or replaced with other
scenes.
D Access the “PARENTAL LOCK“ menu.
Press rt repeatedly to
move H to “PARENTAL
LOCK“, then press OK.
● The “PARENTAL LOCK“ sub-
menu appears on the TV
screen.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
● It is possible to access the
“PARENTAL LOCK“ menu only
in the stop mode when a DVD
disc is loaded on the unit.
E Access the country code menu.
PARENTAL LOCK
Press rt repeatedly to
move H to “COUNTRY
CODE“, then press OK.
COUNTRY CODE
SET LEVEL
PASSWORD
EXIT
US
NONE
_
_
_
_
SELECT
OK
USE
TO SELECT. USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
Press rt repeatedly to
move H to select the country
code, then press OK.
PARENTAL LOCK
COUNTRY CODE
SET LEVEL
PASSWORD
EXIT
US
UG
UM
US
UY
UZ
VA
NONE
_
_
_
_
● See “Country/Area Code List
for Parental Lock” (੬ pg. 58).
● The H moves to “SET LEVEL”.
VC
SELECT
OK
USE
TO SELECT. USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
G Select the Level.
Press OK, then press rt
repeatedly to move H to
select the level of restriction,
then press OK.
PARENTAL LOCK
COUNTRY CODE
SET LEVEL
PASSWORD
EXIT
US
NONE
NONE
_
_
_
_
8
7
6
5
4
3
● The H moves to
“PASSWORD”.
SELECT
OK
USE
TO SELECT. USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
● The smaller the value of level
is, the more restrictive the
Parental Lock level is.
● Select “NONE” to cancel this
function.
To set Parental Lock for the first time
A Turn on the unit.
Press POWER (1).
B Select the DVD deck.
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
57
H Enter the password.
Press the number keys to
enter a four-digit number as
your password, then press
OK.
Press the appropriate number keys to enter 4-digit
password, then press OK.
PARENTAL LOCK
COUNTRY CODE
SET LEVEL
PASSWORD
EXIT
US
4
_
_
_
_
● The password entered in the this step becomes the new
password. If you do not change the password, enter the same
password as in the step B.
● Even if you want to change only the country code and/or level,
do not forget to enter the password after changing the country
code and/or the level. Otherwise, the new country code and/
or the level will not become effective.
● The H moves to “EXIT”.
SELECT
OK
NEW PASSWORD
TO EXIT, PRESS [SET UP MENU].
?
••• PRESS
0
~
9
KEY
I Return to the OTHERS menu screen.
Press OK.
● The “ OTHERS” menu resumes.
Press SET UP MENU.
To return to the normal screen
NOTES:
Press SET UP MENU.
● When you enter the wrong password more than 3 times in
step B on the left column, the arrow moves to “EXIT”
automatically and rt does not work.
NOTE:
Remember your password, or make a note of it.
● If you forget your password, enter “8888” in step B.
To change the settings
To temporarily release the Parental
Lock
You can change the Parental lock settings later.
When you set the parental level strictly, some discs may not be
played back at all. When you insert such a disc and try to play
back it, the following Parental Lock screen appears on the TV
screen, asking you whether you want the Parental Lock to be
temporarily released or not.
A Access the Parental Lock screen.
A Press SET UP MENU.
B Press w e to select “ OTHERS”.
C Press rt repeatedly to move H to “PARENTAL
LOCK“, then press OK.
● The “PARENTAL LOCK“ sub-menu appears on the TV screen.
● You can only move H to “PASSWORD” or to “EXIT” before
you enter your password.
A Access the password screen.
A Place the disc in the disc
PARENTAL LOCK
tray.
TEMPORARY RELEASE
NOT RELEASE
● If the disc rated higher than the
selected level, the following
screen appears.
_
_
_
_
PASSWORD
B Enter the password.
Press the appropriate number
B Press rt to move H to
“TEMPORARY RELEASE”,
then press OK.
● If you select “NOT RELEASE”,
you cannot play back that disc.
SELECT
OK
PARENTAL LOCK
PASSWORD? ••• PRESS
0
~
9
KEY
keys to enter 4-digit
COUNTRY CODE
SET LEVEL
PASSWORD
EXIT
US
4
password, then press OK.
If you enter the wrong
password, “WRONG!
_
_
_
_
SELECT
OK
NEW PASSWORD
TO EXIT, PRESS [SET UP MENU].
?
••• PRESS
0
~
9
KEY
RETRY...” appears at the
bottom of the TV screen.
Enter the correct password.
B Enter the password.
Press the appropriate number keys to enter 4-digit
password, then press OK.
C Change the country code.
● If you enter the wrong password, “WRONG! RETRY...” appears
on the TV screen. Enter the correct password.
Press rt to select the country code, then press OK.
● See “Country/Area Code List for Parental Lock” (੬ pg. 58).
● When you change the country code, you must select the level.
● If you enter the correct password, the Parental lock is released
and the unit starts playback.
NOTES:
D Change the level.
● When you enter the wrong password more than 3 times in
step B above, the arrow moves to “NOT RELEASE”
automatically and rt do not work. In such a case, press OK,
then press OPEN/CLOSE (x) to remove the disc.
● If you forget your password, enter “8888” in step B.
Press rt to select the desired level, then press OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
58
EN
OPERATIONS ON DVD DECK (cont.)
Country/Area Code List for Parental Lock
AD
AE
Andorra
ES
Spain
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
ET
Ethiopia
AF
FI
FJ
FK
Finland
Fiji
Falkland Islands (Malvinas)
AG
AI
AL
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaijan
Bosnia and Herzegovina
Barbados
Bangladesh
Belgium
FM
FO
FR
Micronesia (Federated States of)
AM
AN
AO
AQ
AR
AS
Faroe Islands
France
France, Metropolitan
Gabon
United Kingdom
Grenada
Georgia
French Guiana
FX
GA
GB
GD
GE
GF
GH
GI
AT
AU
AW
AZ
BA
BB
BD
BE
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe
Equatorial Guinea
Greece
South Georgia and the South Sandwich Islands
Guatemala
Guam
Guinea-Bissau
Guyana
Hong Kong
Heard Island and McDonald Islands
Honduras
Croatia
Haiti
Hungary
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
BF
Burkina Faso
Bulgaria
BG
BH
BI
Bahrain
Burundi
BJ
Benin
BM
BN
BO
BR
BS
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
BT
Bhutan
BV
BW
BY
BZ
CA
CC
CF
Bouvet Island
Botswana
Belarus
Indonesia
Ireland
Israel
India
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
British Indian Ocean Territory
CG
CH
CI
CK
CL
CM
CN
CO
CR
CU
CV
CX
CY
CZ
DE
DJ
Iraq
Switzerland
Côte d’Ivoire
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Iran (Islamic Republic of)
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia
Kiribati
Comoros
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Saint Kitts and Nevis
Korea, Democratic People’s Republic of
Korea, Republic of
Kuwait
Cayman Islands
Kazakhstan
DK
DM
DO
DZ
EC
Lao People’s Democratic Republic
Lebanon
Ecuador
Estonia
Egypt
Western Sahara
Eritrea
EE
EG
EH
ER
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
59
LC
Saint Lucia
Liechtenstein
Sri Lanka
SA
SB
SC
SD
SE
Saudi Arabia
Solomon Islands
Seychelles
LI
LK
LR
LS
LT
LU
LV
LY
Liberia
Sudan
Lesotho
Lithuania
Luxembourg
Latvia
Libyan Arab Jamahiriya
Morocco
Monaco
Moldova, Republic of
Madagascar
Marshall Islands
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia
Niger
Norfolk Island
Nigeria
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Slovakia
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Sao Tome and Principe
El Salvador
Syrian Arab Republic
Swaziland
Turks and Caicos Islands
Chad
SG
SH
SI
SJ
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
SK
SL
SM
SN
SO
SR
ST
SV
SY
SZ
TC
TD
TF
French Southern Territories
Togo
TG
TH
TJ
TK
TM
TN
TO
TP
Thailand
Tajikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
TR
TT
Turkey
Trinidad and Tobago
Tuvalu
TV
TW
TZ
UA
UG
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Taiwan, Province of China
Tanzania, United Republic of
Ukraine
Nicaragua
Netherlands
Norway
NL
NO
NP
NR
NU
NZ
OM
PA
Uganda
Nepal
United States Minor Outlying Islands
United States
Uruguay
Nauru
Niue
New Zealand
Oman
Uzbekistan
Vatican City State (Holy See)
Saint Vincent and the Grenadines
Venezuela
Panama
Peru
French Polynesia
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn
Puerto Rico
Portugal
Palau
Paraguay
PE
PF
Virgin Islands (British)
Virgin Islands (U.S.)
Viet Nam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
Qatar
Réunion
Romania
Russian Federation
Rwanda
Download from Www.Somanuals.com. All Manuals Search And Download.
60
EN
OPERATIONS ON DVD DECK (cont.)
NOTES:
● Because of the disc characteristics or recording condition,
some discs may not be played back or it takes time to start
playback.
About MP3/WMA
Disc
● The unit does not support “packet writing” discs.
● If there are any Tracks (files) which are stored on a disc directly
and do not belong to any Group (directory), the unit
recognized them as belonging to an independent Group.
● The unit plays back Groups/Tracks on an MP3/WMA disc in
the alphabetical order.
● For example, if there are three title Groups [one], [two] and
[three] on a disc, the playback order is [one], [three] then
[two]. Tracks in a Group are played back in the same way.
● Therefore, an MP3/WMA disc on the market may be played
back in the different order from the order printed on its sleeve.
This unit can playback CD discs recorded by the MP3/WMA
format (we refer to those discs as MP3/WMA discs in this
manual).
Operations for MP3/WMA discs are similar to those for Audio
CD discs, though there are some restrictions and differences.
What is MP3?
MP3 is the abbreviation of “MPEG1 Audio Layer 3.” MPEG
Audio is a compression specification that compresses the audio
portion only. This image compression method is used in DVD or
Video CD, etc. The audio data has been compressed into about
1/10.
MP3/WMA control display
The MP3/WMA control display appears on the TV screen and
playback starts when an MP3/WMA disc is loaded.
What is WMA?
WMA is an abbreviation of “Windows Media Audio”, and is an
audio data compression format developed by Microsoft
Corporation. Sound quality of data compressed using WMA is
the same as that of MP3, though the WMA file size is smaller
than that of MP3.
Total group number on
disc
Current track
number
Total track number
in current group
*
On an MP3/WMA disc, each material (song) is recorded on each
Track (file), which usually belongs to a Group (folder).
Track A.mp3
Group 1
Track B.mp3
Track C.mp3
MP3 disc
Group 2
Current group
number
Current track
Total track number
on disc
Current group
Track D.mp3
Track E.mp3
* Elapsed playing time of current track
Elapsed playing time is only shown during playback.
Track F.mp3
Group 4
Group 3
This unit can recognize up to 99 Groups and up to 150 Tracks
per Group.
If a disc includes more than the Tracks above limit, the unit stops
detecting Tracks when the number of detected Tracks reaches the
limit and ignores the subsequent Tracks. The unit also ignores
any non-MP3/WMA file in the disc.
NOTES for making a private MP3/WMA disc using a
CD-R/CD-RW disc:
● Select “ISO9660” as the disc format.
● Finalize the disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
61
Using the MP3/WMA control display
MP3/WMA
Playback
A Turn on the unit.
Press POWER (1).
B Select the DVD deck.
On the unit
You can search and play back desired groups and tracks using
the MP3/WMA control display.
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
On the Remote
C Select the mode.
Be sure to set “MP3&WMA/JPEG” to “MP3&WMA”
before loading a disc. (੬ pg. 79)
● You cannot access the DVD Set Up screen and “X” appears
on the TV screen if a disc is already placed.
D Load the disc.
A Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
B Place the MP3/WMA disc in the disc tray.
● For details, refer to “Placing a Disc” (੬ pg. 7).
C Press OPEN/CLOSE (x) on the DVD deck to close the
disc tray.
● The MP3/WMA control display appears on the TV screen
when an MP3/WMA disc is loaded. (੬ pg. 60)
E Select the group.
Press w e to select the desired group.
F Start playback.
Press rt to select the desired track, then press OK or
PLAY (4).
● You can skip a track across a group. Press SKIP (6) to skip to
the first track of the next group when the last track of the
current group is selected.
G Pause playback.
Press PAUSE (9).
● To resume normal playback, press PLAY (4).
H Stop playback.
Press STOP (8). Press OPEN/CLOSE (x) on the DVD
deck to open the disc tray, then remove the disc.
NOTES:
● PLAY (4), STOP (8), PAUSE (9), SKIP (2) and SKIP (6)
buttons function the same as with Audio CD discs, however,
REW (3) and FF (5) buttons do not function for MP3/
WMA playback.
● Resume playback, Program playback or Random playback also
does not function for MP3/WMA playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
62
EN
OPERATIONS ON DVD DECK (cont.)
Repeat Playback
You can repeat playback of the current group, track or all groups.
● While MP3/WMA control display is on the TV:
A Access the repeat mode.
Press PLAY SETUP during playback.
● The current repeat mode is displayed on the MP3/WMA
control display.
B Select the mode.
Press rt to select the desired repeat mode, then press
OK.
● Each time you press REPEAT, the mode changes as follows:
TRACK]GROUP]ALL]OFF (No indication)](Back to the
beginning)
The current track is played back
repeatedly.
TRACK:
All tracks of the current group are
played back repeatedly.
GROUP:
All tracks are played back
repeatedly.
ALL:
Each track is played back once.
OFF (no indication):
● To stop Repeat Playback, press STOP (8).
● To cancel Repeat Playback, press REPEAT repeatedly until the
repeat mode display disappears on the TV screen.
● You can also quit Repeat Playback in the following cases:
• Press OPEN/CLOSE (x) to open the disc tray.
• Turn off the unit.
To return to the MP3/WMA control display
Press STOP (8).
Group/track selection
To start playback by specifying the group/track number
A Press TITLE.
B Press the number keys (0-10, +10) to enter the group
number.
C Press the number keys (0-10, +10) to enter the track
number.
Example:
To select 3:
To select 14:
To select 20:
Press 3.
Press +10, then 4.
Press +10, then 10.
Or press +10 twice, then 0.
Press +10, +10, then 4.
To select 24:
To select 110: Press +10 ten times, then 10.
● The entered number appears in the track number indication
and playback starts from the track you have specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
63
NOTES:
● We recommend to record a file at 640 x 480 resolution. (If a
file has been recorded at a resolution of more than 640 x 480,
it will take a longer time to be displayed.)
About JPEG Disc
This unit can playback CD discs recorded by the JPEG format
(we refer to those discs as JPEG discs in this manual).
Operations for JPEG discs are similar to those for Audio CD
discs, though there are some restrictions and differences.
● This unit can only play back baseline JPEG files*. Progressive
JPEG files* or lossless JPEG files* cannot be played back.
* Baseline JPEG format: Used for digital cameras, web, etc.
Progressive JPEG format: Used for web.
Lossless JPEG format: An old type and rarely used now.
● Some files on a JPEG disc may be played back distortedly.
● Because of the disc characteristics or recording condition,
some discs may not be played back or it takes time to start
playback.
● The unit does not support “packet writing” discs.
● If there are any Files which are stored on a disc directly and do
not belong to any Group (directory), the unit recognized them
as belonging to an independent Group.
What is JPEG?
JPEG is the abbreviation of “Joint Photographic Expert Group.”
JPEG is a still-picture data compression system.
On a JPEG disc, each still picture is recorded as a file, which
usually belongs to a Group (folder).
● The unit plays back Groups/Files on an JPEG disc in the
alphabetical order.
● For example, if there are three title Groups [one], [two] and
[three] on a disc, the playback order is [one], [three] then
[two]. Files in a Group are played back in the same way.
● Therefore, an JPEG disc on the market may be played back in
the different order from the order printed on its sleeve.
File A.jpg
Group 1
File B.jpg
File C.jpg
JPEG disc
Group 2
JPEG control display
File D.jpg
File E.jpg
The JPEG control display appears on the TV screen and playback
starts when a JPEG disc is loaded.
File F.jpg
Group 4
Total group number on
disc
Current file
number
Total file number in
current group
Group 3
This unit can recognize up to 99 Groups and up to 150 Files per
Group.
If a disc includes more than the Files above limit, the unit stops
detecting Files when the number of detected Files reaches the
limit and ignores the subsequent Files. The unit also ignores any
non-JPEG file in the disc.
NOTES for making a private JPEG disc using a CD-R/
CD-RW disc:
● Select “ISO9660” as the disc format.
● Finalize the disc.
Current group
number
Current file
Total file number on
disc
Current group
Download from Www.Somanuals.com. All Manuals Search And Download.
64
EN
OPERATIONS ON DVD DECK (cont.)
Using the JPEG control display
JPEG Playback
A Turn on the unit.
Press POWER (1).
You can search and play back desired groups and files using the
JPEG control display.
B Select the DVD deck.
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
On the unit
On the Remote
C Select the mode.
Be sure to set “MP3&WMA/JPEG” to “JPEG” before
loading a disc. (੬ pg. 79)
● You cannot access the DVD Set Up screen and “X” appears
on the TV screen if a disc is already placed.
D Load the disc.
A Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
B Place the JPEG disc in the disc tray.
● For details, refer to “Placing a Disc” (੬ pg. 7).
C Press OPEN/CLOSE (x) on the DVD deck to close the
disc tray.
● The JPEG control display appears on the TV screen when a
JPEG disc is loaded. (੬ pg. 63)
E Select the group.
Press w e to select the desired group.
F Start playback.
Press rt to select the desired file, then press OK or
PLAY (4).
● You can skip a file across a group. Press SKIP (6) to skip to
the first file of the next group when the last file of the current
group is selected.
The slide-show playback starts from the selected file.
● After selecting a file, press PLAY (4) to starts slide-show
playback from the selected file, or press OK to show the
selected file.
G Pause playback.
Press PAUSE (9).
● To resume normal playback, press PLAY (4).
H Stop playback.
deck to open the disc tray, then remove the disc.
Press STOP (8). Press OPEN/CLOSE (x) on the DVD
NOTES:
● PLAY (4), STOP (8), PAUSE (9), SKIP (2) and SKIP (6)
buttons function the same as with Audio CD discs, however,
REW (3) and FF (5) buttons do not function for JPEG
playback.
● Resume playback, Program playback or Random playback also
does not function for JPEG playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
65
Repeat Playback
You can repeat playback of the current group, file or all groups.
● While JPEG control display is on the TV:
A Access the repeat mode.
Press PLAY SETUP while the JPEG Control screen is
displayed.
● The current repeat mode is displayed on the JPEG control
display.
B Select the mode.
Press rt to select the desired repeat mode, then press
OK.
● Each time you press REPEAT, the mode changes as follows:
GROUP]ALL]OFF (No indication)](Back to the beginning)
All files of the current group are
played back repeatedly.
GROUP:
All files are played back
repeatedly.
ALL:
Each file is played back once.
OFF (No indication):
C Start playback.
Press PLAY (4).
● To stop Repeat Playback, press STOP (8).
● To cancel Repeat Playback, press REPEAT repeatedly until the
repeat mode display disappears on the TV screen.
● You can also quit Repeat Playback in the following cases:
• Press OPEN/CLOSE (x) to open the disc tray.
• Turn off the unit.
To return to the JPEG control display
Press STOP (8).
Group/file selection
Zooming
To start slide-show playback by specifying the group/file
Press ZOOM during playback.
number
A Press TITLE.
● When you want to zoom the picture during slide-show
playback, first press PAUSE (9), then press ZOOM.
● For details, refer to “Zooming” (੬ pg. 43).
B Press the number keys (0-10, +10) to enter the group
number.
C Press the number keys (0-10, +10) to enter the file
number.
Example:
To select 3:
To select 14:
To select 20:
Press 3.
Press +10, then 4.
Press +10, then 10.
Or press +10 twice, then 0.
Press +10, +10, then 4.
To select 24:
To select 110: Press +10 ten times, then 10.
● The slide-show playback starts from the file you have
specified.
● To display only the selected file, then press OK. To start slide-
show playback from that file, press OK again.
Download from Www.Somanuals.com. All Manuals Search And Download.
66
EN
EDITING (VCR DECK)
You can use a camcorder as the source player and your
unit as the recording deck.
Edit From A
Slide the TV/VCR/DVD switch to the right.
Camcorder
A If the camcorder has no S-VIDEO output connector:
Recorder
A Make connections.
A If the camcorder has no S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and VIDEO
OUT connectors to the unit’s front panel AUDIO and
VIDEO input connectors.
B If the camcorder has an S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and
S-VIDEO OUT connectors to the unit’s front panel
AUDIO and S-VIDEO input connectors.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the AUDIO L input connector on your unit.
● When a Master Edit Control-equipped JVC camcorder is used,
the camcorder is capable of controlling the unit. Refer to the
camcorder’s instruction manual for operating procedure.
To PAUSE
AUDIO input
connector
VIDEO
input
Audio cable (not provided)
Video cable (not provided)
B Select the VCR deck.
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the unit
Mini-plug cable
(not provided)
(JVC camcorder
only)
VIDEO OUT
AUDIO OUT
On the Remote
Press VCR so that the VCR indicator lights up.
Camcorder
Player
Press AUX (number key “0”) and/or CH to select “F-1”.
● When using S VIDEO connector, set “FRONT AUX INPUT” to
To EDIT
B If the camcorder has an S-VIDEO output connector:
“VIDEO”. (੬ pg. 77)
S-VIDEO input
Recorder
D Set the edit mode.
See “PICTURE CONTROL” on page 74.
E Engage the Record Pause mode.
Use PLAY (4), REW (3), or FF (5) to locate the
point where you start recording, then press and hold
PAUSE (9) and press REC (7) to engage the Record Pause
mode.
To PAUSE
connector
AUDIO input
Audio cable (not provided)
S-Video cable (provided)
F Start the camcorder.
Mini-plug cable
(not provided)
(JVC camcorder
only)
Engage the Play mode of the camcorder.
S-VIDEO OUT
AUDIO OUT
G Start the unit.
Press PLAY (4) to engage the Record mode of the unit.
Camcorder
NOTES:
● Dubbing is also possible using the rear panel connectors.
● All necessary cables can be obtained from your dealer.
● When you select “EDIT” to dub tapes in step D, be sure to
select “AUTO” (or “NORM” when “VIDEO CALIBRATION” is
set to “OFF”) after you finish dubbing the tapes.
Player
To EDIT
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
67
You can use your unit as the source player or as the
recording deck.
Edit To Or From
Another Video
Recorder
Slide the TV/VCR/DVD switch to the right.
A Make connections.
A When using your unit as the source player ...
... connect its AUDIO/VIDEO OUTPUT connectors to the
audio/video input connectors on another recorder.
B When using your unit as the recording deck ...
... connect its AUDIO/VIDEO INPUT connectors to the
audio/video output connectors on another recorder.
● If connecting a unit with an S-VIDEO input/output connector,
it is recommended to use the supplied S-Video cable to
minimize picture degradation while editing.
A
TV receiver
Player
Your unit
B Select the VCR deck.
On the unit
S-Video cable
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
Audio/video
cable
Audio/video cable
On the Remote
AV mode
Press VCR so that the VCR indicator lights up.
C Set the input mode of recording deck.
With this video unit, press AUX (number key “0”) and/or
CH to select “L-1”.
Another recorder
● When using S VIDEO connector, set “REAR AUX INPUT” to
“S-VIDEO”. (੬ pg. 77)
Recorder
Recorder
● When using VIDEO connector, set “REAR AUX INPUT” to
instruction manual.
B
Your unit
TV receiver
D Set the edit mode.
See “PICTURE CONTROL” on page 74.
AV mode
S-Video cable
Engage the Record Pause mode of the
recording deck.
E
Audio/video
cable
Locate the point where you start recording, then engage
the Record Pause mode.
Audio/video
cable
F Start the source player.
Another recorder
Engage the Play mode of the source player.
Player
G Start the recording deck.
Advantages of S-VHS video recorders
Engage the Record mode of the recording deck.
You can edit from VHS to S-VHS, S-VHS to VHS, or, from
S-VHS to S-VHS.
NOTES:
● From VHS to S-VHS: Record VHS playback signals in the
S-VHS mode. Although the picture quality is inherently
limited by that of the original, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
● From S-VHS to VHS: Because the picture quality of the
source material is very high, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
● From S-VHS to S-VHS: All signals will be transferred with
minimum degradation.
● All necessary cables can be obtained from your dealer.
● When you select “EDIT” to dub tapes in step D, be sure to
select “AUTO” (or “NORM” when “VIDEO CALIBRATION” is
set to “OFF”) after you finish dubbing the tapes.
● When you use this unit as the source player for editing, be sure
to set “SUPERIMPOSE” to “OFF” before starting. (੬ pg. 75)
Download from Www.Somanuals.com. All Manuals Search And Download.
68
EN
EDITING (VCR DECK) (cont.)
You can dub selected scenes from the DVD disc to a cassette,
starting and stopping wherever you wish.
However, it is not possible to dub the copy-protected disc.
In such case, “ERROR” appears on the front display panel.
Dubbing
(from DVD to VCR)
A Load a cassette and place a disc.
For the VCR deck
Insert a cassette with the record safety tab intact.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
For the DVD deck
A Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
B Place the disc in the disc tray.
C Press OPEN/CLOSE (x) on the DVD deck to close the
disc tray.
B Prepare the VCR deck for dubbing.
A Press VCR.
B Press SP/EP to select recording speed.
C Search for the point where you want to start dubbing
by pressing PLAY (4), FF (5) or REW (3) then
press STOP (8).
C Prepare the DVD deck for dubbing.
A Press DVD.
B Search for the point where you want to start dubbing
by pressing PLAY (4), FF (5) or REW (3).
C Press PAUSE (9) to pause playback a little before the
start point.
D Start dubbing.
Press and hold REC (7), then press PLAY (4) on the
Remote.
● “DUB” lights on the front display panel.
E End dubbing.
Press STOP (8).
● Be sure to press STOP (8) while the VCR indicator lights up on
the unit.
● If you press STOP (8) or EJECT (x) with the DVD deck
selected, the dubbing stopped, but the opening screen is also
recorded.
NOTES:
● You cannot start dubbing when the scan mode is set to the
progressive mode. Set it to the interlace mode. (੬ pg. 82)
● Set “ON SCREEN GUIDE” to “OFF” (੬ pg. 81) if you do not
want to record the on-screen display for DVD discs during
dubbing.
● There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
● The superimposed indication during the operation or dubbing
is not recorded.
● Set “PICTURE CONTROL” to “EDIT”. (੬ pg. 74)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
69
EDITING (DVD DECK)
You can dub selected audio from the DVD or Audio CD disc to a
MD etc.
However, it is not possible to dub the copy-protected disc.
Digital Audio
Dubbing
Example: Dubbing to a MD
A Make connections.
Connect the optical cable between the unit and the
digital audio device.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
B Place a disc and load a MD.
For the DVD deck
A Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
Recorder
B Place the disc in the disc tray.
C Press OPEN/CLOSE (x) on the DVD deck to close the
disc tray.
For the digital audio device
Insert a MD.
Digital audio device
(MD deck etc.)
C Prepare the DVD deck for dubbing.
A Press DVD and select the audio to be dubbed.
B Search for the point where you want to start dubbing
by pressing PLAY (4), FF (5) or REW (3) then
press STOP (8).
Optical cable
(not supplied)
C Press REW (3) a little, then press PLAY (4) to start
playback.
Player
D Press PAUSE (9) to pause playback a little before the
start point.
D Prepare the audio device for dubbing.
Select the input mode.
Rear of unit
DIGITAL AUDIO OUT
E Start dubbing.
A Press PLAY (4) to start playback on the DVD deck.
B Start recording on the audio device.
Note for connection:
Remove the connector cover
from the unit and remove the
protection cap from the
cable.
F End dubbing.
Stop recording on the audio device. Then press STOP (8)
to stop playback on the DVD deck.
NOTES:
● There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
● You can also dub a Video CD or SVCD. Set “DIGITAL AUDIO
OUTPUT” to “PCM ONLY”. (੬ pg. 79)
Download from Www.Somanuals.com. All Manuals Search And Download.
70
EN
REMOTE
On the Remote
Keep pressing VCR down during steps A – B.
Remote Control
Functions
A Change the remote control code.
Press the number key “1” for A, “2” for B, “3” for C or
“4” for D.
B Set the remote control code.
Remote A/B/C/D Code Switching
The Remote is capable of controlling four JVC video units
independently. Each of units can respond to one of four codes
(A, B, C or D). The remote control is preset to send A code
signals because your unit is initially set to respond to A code
signals. You can easily modify your unit to respond to B, C or D
code signals.
Press OK to set the code.
On the unit
C Turn off the unit.
Before performing the following steps:
Slide the TV/VCR/DVD switch to the right.
Press POWER (1).
D Display the code.
Press PLAY (4) on the unit for over 5 seconds while the
unit is turned off. The code currently set appears on the
front display panel.
● If the code displayed on the front display panel is different
from the code set on the Remote, go to step E.
E Change the unit’s code.
Press STOP (8) on the Remote. The code currently set on
the Remote will be applied to the unit.
NOTE:
Once you unplug the end of the mains power cord from the
mains, the remote control code is back to A.
Download from Www.Somanuals.com. All Manuals Search And Download.
71
TV Multi-Brand Remote Control
A Set the TV brand code.
Enter your TV’s brand code using the number keys, then
press OK.
Press POWER (1) on the unit’s Remote to turn on the TV
and try operations (੬ step B).
● Once you have set the remote control to operate the TV, you
do not have to repeat this step until you replace your Remote’s
batteries.
Your Remote can operate the basic functions of your TV set. In
addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
Keep pressing VCR down during step A.
Before performing the following steps:
● Turn off the TV using its Remote.
● Slide the TV/VCR/DVD switch to the left.
● Some brands of TV have more than one code. If the TV does
not function with one code, try entering another.
B Operate the TV.
Press the corresponding button: POWER (1), TV/VCR,
TV/VCR CH +/–, TV VOL+/– (Volume), MUTE (TV
Muting), number keys.
● For some brands of TV, you must press OK after having pressed
the number keys.
BRAND NAME
CODE
JVC
01, 03
10
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
02
03
04, 11
05
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
06
07
12
13
13
08
09
IMPORTANT
Although the supplied remote control unit is compatible with
JVC televisions, as well as many other models, it may not work
with your TV, or in some instances, may have limited function
capability.
Download from Www.Somanuals.com. All Manuals Search And Download.
72
EN
REMOTE (cont.)
Connecting To A Dolby Digital Decoder
or An Amplifier With A Built-in DTS
(DVD deck only)
These instructions enable you to connect your unit to dolby digital decoder or amplifier with a built-in DTS.
DIGITAL AUDIO OUT
Back of unit
Dolby Digital decoder or
amplifier with a built-in DTS
To DIGITAL AUDIO
input
Note for connection:
Remove the connector cover from the
unit and remove the protection cap from
the cable.
Optical cable
(not supplied)
CAUTIONS:
Make connections.
● This unit has a dynamic range of more than 80 dB with regards
to its Hi-Fi audio capability. It is recommended that you check
the maximum level if you are going to listen to the Hi-Fi audio
signals through a stereo amplifier. A sudden surge in the input
level to the speakers may damage them.
Connect the optical cable between the unit and the
NOTES:
● Some speakers and televisions are specially shielded to
prevent television interference. If both are of the non-shielded
type, do not place the speakers adjacent to the TV set as this
can adversely affect the video playback picture.
● For Dolby digital sound, set “DIGITAL AUDIO OUTPUT” to
“DOLBY DIGITAL/PCM”. (੬ pg. 79)
● For DTS sound, set “DIGITAL AUDIO OUTPUT” to “STREAM/
PCM”. (੬ pg. 79)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
SUBSIDIARY SETTINGS
You can change various mode settings on the Function
Set screen by following the procedure described below.
● For each mode setting, see pages 74 to 77.
Mode Set
A Turn on the unit.
(VCR deck)
Press POWER (1).
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
B Select the VCR deck.
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
C Access the Main Menu screen.
Press SET UP MENU.
D Access the Function Set screen.
Press rt to move the
highlight bar (arrow) to
“FUNCTION SET”, then
press OK or e.
E Select the mode.
Press rt to move the highlight bar (arrow) to the item
you want to change.
F Select the mode setting.
Press OK or e.
G Return to the normal screen.
Press SET UP MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
74
EN
SUBSIDIARY SETTINGS (cont.)
* The default setting is bold in the table below.
You can record in SP mode on VHS cassettes with S-VHS picture quality. You can
play back a tape recorded using the S-VHS ET function on most of S-VHS recorders
and of VHS recorders equipped with SQPB (S-VHS QUASI PLAYBACK) function.
(Notice some recorders are not compatible with the S-VHS ET function.)
When this function is set to “ON”, the S-VHS indicator lights up on the front
display panel.
8 S-VHS ET
ON
OFF
NOTES:
● You can activate the S-VHS ET function only before you start recording on a VHS cassette.
● Before recording, make sure that “VIDEO CALIBRATION” is set to “ON”. (੬ below)
● You cannot activate the S-VHS ET function:
— while recording is in progress.
— while timer-recording or Instant Timer Recording (੬ pg. 31, 34) is in progress.
— while Video Calibration (੬ pg. 33) is in progress.
● The S-VHS ET function does not work with S-VHS cassettes.
● To keep the highest quality recording and playback pictures over a long period of time,
S-VHS recording on S-VHS cassettes is recommended.
quality will not improve even if the S-VHS ET function is used. Check the recording quality
before you start important recordings.
● While playing back a tape recorded using the S-VHS ET function on some recorders, noise
may appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)
● In the variable speed search, still, slow-motion or frame-by-frame playback modes
(੬ pg. 27), noise may appear. If these modes are performed frequently on a tape recorded
deteriorated.
When this function is set to “ON”, this unit checks the condition of the tape in use
during playback and recording, and compensates to provide the highest-possible
pictures. This takes place whenever you play back a tape or start recording after
inserting a tape. (੬ pg. 33)
8 VIDEO CALIBRATION
ON
OFF
This feature helps you to adjust the playback picture quality according to your
preference. Normally select “AUTO”.
8 PICTURE CONTROL
AUTO
EDIT
AUTO
:
Provides the optimised picture benefits of the VIDEO CALIBRATION
Picture System.
SOFT
SHARP
EDIT
:
Minimizes picture degradation during editing (recording and playback).
SOFT
:
Reduces image coarseness when viewing overplayed tapes containing a
lot of noise.
SHARP
Clearer, sharper-edged picture when viewing images with lots of flat,
same-coloured surfaces such as cartoons.
NOTES:
● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you
select another mode.
● When you select “EDIT” to dub tapes, be sure to select “AUTO” after you finish dubbing the
tapes.
● When “VIDEO CALIBRATION” is “OFF”, “PICTURE CONTROL” switches automatically
from “AUTO” to “NORM”.
Download from Www.Somanuals.com. All Manuals Search And Download.
* The default setting is bold in the table below.
When this function is set to “ON”, various operational indicators appear on the
8 SUPERIMPOSE
TV screen. Messages appear in the selected language. (੬ pg. 18)
ON
OFF
NOTES:
● When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE”
to “OFF” before starting.
● During playback, the operation mode indicators may be disturbed depending on the
type of tape being used.
When this function is set to “ON”, the unit automatically switches to EP mode
to allow complete recording if there is not enough tape to record the entire
program while timer-recording in SP mode.
8 AUTO SP]EP TIMER
ON
OFF
For Example:
Recording a program of 140 minutes in length onto a 120-minute tape
Approximately 110 minutes
SP mode
Approximately 30 minutes
EP mode
Total 140 minutes
Make sure you set this function to “ON”, before the timer-recording starts.
NOTES:
● If you have programed the unit to timer-record 2 or more programs, the second
program and those thereafter may not fit on the tape if you set “AUTO SP]EP TIMER”
to “ON”. In this case, make sure the mode is not engaged, then set the tape speed
manually during timer programing.
● In order to ensure that the recording fits on the tape, this feature may leave a slight non-
recorded section at the end of the tape.
● There may be some noise and sound disturbance at the point on the tape where the unit
switches from SP to EP mode.
● The Auto SP]EP Timer feature is not available during ITR (Instant Timer Recording),
and the feature will not work properly on the following tapes: T(ST)-30, T(ST)-60,
T(ST)-90, and T(ST)-120
When this function is set to “ON”, you can automatically correct vertical
vibration in the picture when playing back unstable recordings made on
another recorder.
8 VIDEO STABILIZER
ON
OFF
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording and during special
effects playback.
● The on-screen display may jitter vertically when this function is set to “ON”.
● To watch recordings with close-caption, set this function to “OFF”.
When this function is set to “ON”, the TV screen becomes all blue when
receiving a channel not in use.
8 BLUE BACK
ON
OFF
NOTE:
When you want to receive an unstable channel with poor signals, set this function to
“OFF”.
Download from Www.Somanuals.com. All Manuals Search And Download.
76
EN
SUBSIDIARY SETTINGS (cont.)
* The default setting is bold in the table below.
● When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on both the normal and
Hi-Fi tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on both the Hi-Fi
and normal tracks.
● When this function is set to “OFF”, the SAP audio cannot be recorded.
8 2ND AUDIO RECORD
ON
OFF
NOTES:
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about 5 seconds if the program is a
stereo broadcast.
● The “SAP” indicator appears on the screen for about 5 seconds if the program is a SAP
broadcast.
● Both indicators appear when a stereo program is accompanied by SAP sound.
This unit can record two sound tracks simultaneously (normal and Hi-Fi) on a
Hi-Fi stereo tape. You can select the sound track(s) to listen to while playing
back a Hi-Fi stereo tape. In addition, when playing back a prerecorded tape
containing two separate audio programs on the Hi-Fi tracks, you can choose
either one by selecting either “HI-FI L” or “HI-FI R”.
8 AUDIO MONITOR
HI-FI
HI-FI L
HI-FI R
NORM
MIX
HI-FI:
Normally select this. Hi-Fi sound is played back.
Sound on the left Hi-Fi channel is played back.
Sound on the right Hi-Fi channel is played back.
Sound on the normal track is played back.
Both sounds on the Hi-Fi track and normal track are mixed
HI-FI L:
HI-FI R:
NORM:
MIX:
NOTES:
● While playing back a monaural tape, sounds on the normal track will be heard
regardless of this setting.
● You can also use the A.MONITOR button on the Remote to select the desired monitor
sound. (੬ pg. 29)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
77
* The default setting is bold in the table below.
Your unit can record in S-VHS (Super VHS), S-VHS ET or VHS.
8 S-VHS MODE
ON
● To record in S-VHS:
OFF
Set “S-VHS MODE” to “ON”. Then, insert a cassette marked “S-VHS”. The
S-VHS indicator lights up on the front display panel.
The S-VHS recording mode is selected.
Set “S-VHS ET” to “ON”. (੬ pg. 74) Then, insert a cassette marked “VHS”. The
S-VHS indicator lights up on the front display panel.
● To record in VHS:
Insert a cassette marked “VHS”.
Set “S-VHS ET” to “OFF”. (੬ pg. 74)
The VHS recording mode is automatically selected regardless of the “S-VHS
MODE” setting.
● To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front
display panel. Then, set “S-VHS MODE” to “OFF”. The S-VHS indicator goes
off.
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS
indicator lights up on the front display panel regardless of the “S-VHS MODE” setting.
Select the appropriate mode depending on the connector being used on the
front panel.
8 FRONT AUX INPUT
VIDEO
S-VIDEO
VIDEO:
To use the VIDEO input connector on the front panel.
To use the S-VIDEO input connector on the front panel.
S-VIDEO:
Select the appropriate mode depending on the connector being used on the
rear panel.
8 REAR AUX INPUT
VIDEO
S-VIDEO
VIDEO:
To use the VIDEO input connector on the rear panel.
To use the S-VIDEO input connector on the rear panel.
S-VIDEO:
When this function is set to “3H”, the unit is turned off automatically if no
operation is done within 3 hours. “AUTO POWER OFF IN 3 MIN” appears on
the screen 3 minutes before the unit is turned off.
8 AUTO POWER OFF
3H
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
78
EN
SUBSIDIARY SETTINGS (cont.)
● The procedure shows how to set “RESUME” to “ON”
on the DVD Set Up menu screen as an example.
Mode Set
A Turn on the unit.
(DVD deck)
Press POWER (1).
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
B Select the DVD deck.
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
C Access the DVD Set Up menu screen.
OTHERS
A Press SET UP MENU.
B Press w e to select
RESUME
ON
ON SCREEN GUIDE
PARENTAL LOCK
ON
“
OTHERS”.
● Each time you press the
button, the setup menus
change as follows;
SELECT
OK
USE
TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP MENU].
LANGUAGE] PICTURE] AUDIO] OTHERS
](Back to the beginning)
D Select the mode.
Press rt to move H to “RESUME”, then press OK.
E Select the mode setting.
Press rt to select “ON”, then press OK.
F Return to the normal screen.
Press SET UP MENU.
screen by following the procedure described below.
● For each mode setting, see pages 79 to 81.
MENU LANGUAGE (੬ pg. 20)
LANGUAGE
SUBTITLE (੬ pg. 20)
ON SCREEN LANGUAGE (੬ pg. 19)
MONITOR TYPE (੬ pg. 16, 79)
PICTURE SOURCE (੬ pg. 79)
PICTURE
SCREEN SAVER (੬ pg. 79)
MP3&WMA/JPEG (੬ pg. 79)
AUDIO
D. RANGE CONTROL (੬ pg. 80)
OUTPUT LEVEL (੬ pg. 80)
RESUME (੬ pg. 81)
ON SCREEN GUIDE (੬ pg. 81)
PARENTAL LOCK (੬ pg. 56)
OTHERS
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
79
Picture Settings
* The default setting is bold in the table below.
You can select the monitor type depending the TV used when you play back
DVD VIDEO discs recorded for wide-screen TVs. For more details, refer to
“Monitor Set (DVD deck)” (੬ pg. 16)
8 MONITOR TYPE
16:9 NORMAL
16:9 AUTO
4:3 LB
4:3 PS
You can obtain optimal picture quality by selecting whether the content on the
disc is processed by field (video source) or by frame (film source).
Normally set to “AUTO”.
8 PICTURE SOURCE
VIDEO (NORMAL)
VIDEO (ACTIVE)
FILM
VIDEO (NORMAL):
Suitable for playing back a video source disc with relatively a
few moments.
AUTO
VIDEO (ACTIVE):
Suitable for playing back a video source disc with relatively a
lot of movements.
FILM:
Suitable for playing back a film or progressive source disc.
Used to play back a disc containing both video and film
source materials. This unit recognizes the picture type (film or
video source) of the current disc according to the disc
information.
AUTO:
● If the playback picture is unclear or noisy, or the oblique lines of the picture
are rough, try to change to other modes.
The TV screen may be burned out if a static picture is displayed for a long time.
When this function is set to “ON”, the unit automatically activates the screen
saver function if a static picture, such as an on-screen display or menu is
displayed for over 5 minutes.
8 SCREEN SAVER
ON
OFF
NOTE:
This function is not available for Audio CDs and MP3/WMA discs.
You can select files to play back, when both MP3/WMA files and JPEG files are
recorded on a disc.
8 MP3&WMA/JPEG
MP3&WMA
JPEG
MP3&WMA: Select this to play back MP3/WMA files.
JPEG:
Select this to play back JPEG files.
NOTE:
You cannot access the DVD Set Up screen and “X” appears on the TV screen if a disc is
already placed.
Audio Settings
* The default setting is bold in the table below.
Set to the appropriate mode according to the type of the device connected to
DIGITAL AUDIO OUT connector on the rear of unit.
It is not necessary to set this mode when you connect no device to DIGITAL
AUDIO OUTconnector.
8 DIGITAL AUDIO OUTPUT
PCM ONLY
DOLBY DIGITAL/PCM
STREAM/PCM
PCM ONLY:
Select this when you connect the unit’s DIGITAL AUDIO OUT
connector to the linear PCM digital input connector of other audio
device.
DOLBY DIGITAL/PCM:
Select this when you connect the unit’s DIGITAL AUDIO OUT
connector to the digital input connector of a Dolby Digital decoder
or an amplifier with a built-in Dolby Digital decoder.
STREAM/PCM:
Select this when you connect the unit’s DIGITAL AUDIO OUT
connector to the digital input connector of an amplifier with a built-
in DTS, Dolby Digital, or MPEG multichannel decoder.
Download from Www.Somanuals.com. All Manuals Search And Download.
80
8 ANALOG DOWN MIX
DOLBY SURROUND
STEREO
EN
SUBSIDIARY SETTINGS (cont.)
Set to the appropriate mode according to your audio system when you play
back a DVD VIDEO disc recorded with surround multichannel audio. This
setting affects only the analogue audio output signal from the AUDIO OUTPUT
connectors (DVD) when playing back a DVD VIDEO disc recorded with
surround multichannel audio.
DOLBY SURROUND:
Select this when you enjoy multichannel surround audio by
connecting the unit’s analogue AUDIO OUTPUT connector
(DVD) to a surround decoder or an internal amplifier.
Select this when you enjoy conventional 2-channel stereo
audio by connecting the unit’s analogue AUDIO OUTPUT
you dub audio of a DVD VIDEO disc recorded with surround
audio to your MD, cassette, etc.
STEREO:
NOTE:
The “ANALOG DOWN MIX” function does not work when the 3D Phonic function is
activated. (੬ pg. 44)
The dynamic range (the difference between the loudest sound and the quietest
one) can be compressed during playback of a program encoded in Dolby
Digital format.
This function takes effect when a DVD VIDEO disc recorded in Dolby Digital
format is played back at low or middle volume.
8 D. RANGE CONTROL
WIDE RANGE
NORMAL
TV MODE
WIDE RANGE: Select this to inactivate this function when you enjoy wide
dynamic range program.
NORMAL:
TV MODE:
Normally select this setting to activate this function.
Select this when you hear the sound through the TV's
speaker(s).
NOTES:
● This function works only when playing back a disc recorded with Dolby Digital format.
The setting is not effective for other discs.
● This function does not work when the 3D Phonic function is activated. (੬ pg. 44)
You can lower the output level of analog audio to accommodate the unit to the
connected A/V equipment.
8 OUTPUT LEVEL
STANDARD
LOW
STANDARD: Normally select this.
LOW:
The output level of analog audio is lowered.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
81
Output
Playback discs
STREAM/PCM
DTS bitstream
DOLBY DIGITAL/PCM
PCM ONLY
DVD VIDEO with
48 kHz, 16/20/24 bit linear
PCM
48 kHz, 16 bit linear PCM
DVD VIDEO with DTS
44.1 kHz, 16 bit stereo linear PCM
DVD VIDEO with Dolby
Digital
48 kHz, 16 bit stereo linear
PCM
Dolby Digital bitstream
44.1 kHz, 16 bit stereo linear PCM
44.1 kHz, 16 bit stereo linear PCM
Linear PCM
Audio CD/Video CD
Audio CD with DTS
MP3/WMA disc
DTS bitstream
NOTES:
● The unit is not equipped with the DTS decoding function.
● When you play back a DVD VIDEO or Audio CD disc with DTS, use a DTS decoder to get correct signals from your speakers.
Never use the unit’s analog output connectors, which output incorrect signals that may damage your speakers.
● If you connect the analog outputs and digital outputs simultaneously, be sure to select the source of the amplifier correctly, or
set the level control of the amplifier connected to the analog outputs to minimum.
Others Settings
* The default setting is bold in the table below.
When this function is set to “ON”, you can use the resume function.
8 RESUME
(੬ pg. 43)
ON
OFF
DISC RESUME
ON:
You can start playback from the resume point of the
placed disc.
OFF:
DISC RESUME:
You cannot use the resume function.
The unit retains a memory of the resume points of
the last 30 discs played back, even though they
have been ejected.
NOTE:
This function is not available for Audio CDs and MP3/WMA discs.
When this function is set to “ON”, the unit can display “on-screen
guide” icons or characters which shows the conditions of the unit or
disc.
8 ON SCREEN GUIDE
ON
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
82
EN
SUBSIDIARY SETTINGS (cont.)
Child Lock
Scan Mode Set
● Turn on the TV and select the VCR channel (or AV
mode).
(DVD deck)
● Slide the TV/VCR/DVD switch to the right.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
You can disable the unit’s operation.
A Set the Child Lock.
This unit supports the progressive scan system (eg. 480p*)
as well as the conventional interlaced scan system (eg.
480i*).
If your TV equipped with component video connectors
supports the progressive video input, you can enjoy a
high quality picture by setting the progressive scan mode
to active.
Press and hold POWER (1) on the Remote for more
than 10 seconds while the unit is turned on. The unit
turns off, and “CL“ appears on the front display panel.
● Refer also to the instruction manuals supplied with your TV.
● If your TV equipped with component video connectors does
not support the progressive video input, do not change the
scan mode to the “PROGRESSIVE”.
● To release the child lock, press and hold POWER (1) on the
Remote until the unit turns on.
* 480p and 480i indicate the number of scanning lines and
scanning format of an image signal.
• 480p indicates 480 scanning lines with progressive format.
• 480i indicates 480 scanning lines with interlaced format.
NOTES:
● When the child lock function is in use, keep the Remote out of
the children’s reach.
● Timer recording programs will be performed even if the child
lock function activated.
A Switch the mode.
During playback or while stopped, press and hold
PROGRESSIVE SCAN on the unit or DVD on the Remote
for more than 3 seconds, to change the scan mode
between Progressive and Interlace mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
83
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are
often easily corrected, and this can save you the trouble of sending your unit off for repair.
POWER
SYMPTOM
1. No power is supplied to the unit.
POSSIBLE CAUSE
● The AC power cord is disconnected.
● The batteries are discharged.
CORRECTIVE ACTION
Connect the AC power cord.
2. The Remote won’t function.
Replace the dead batteries with new ones.
TAPE TRANSPORT (VCR deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. During recording, the tape does not
run. “⅜” lights up on the front display
panel.
● The unit is in the Record Pause mode.
Press PLAY (4) to resume recording.
2. The tape will not rewind or fast-
forward.
● The tape is already fully rewound or
fast-forwarded.
Check the cassette.
PLAYBACK (VCR deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. The VCR deck can not be operated.
● The VCR deck is not selected.
On the unit
Press VCR/DVD repeatedly so that the
On the Remote
up.
2. The playback picture does not appear
while the tape is running.
● If you are using the RF connection,
— the TV receiver’s channel selector is
not set to the VCR channel.
If you are using the RF connection,
— set the TV receiver to the VCR channel.
— perform “Set the VCR channel.”
— the unit’s VCR channel has not been (੬ pg. 12).
correctly set.
● If you are using the AV, S-VIDEO or
Component Video connection, the TV
receiver is not set to the AV mode.
If you are using the AV or S-VIDEO
Component Video connection, set the TV
to its AV mode.
3. Noise appears during visual search.
● This is normal.
4. Noise appears during normal
playback.
● The automatic tracking mode is
engaged.
Try manual tracking. (੬ pg. 29)
5. The playback picture is blurred or
interrupted while TV broadcasts are
clear or “USE CLEANING CASSETTE”
message appears on the screen.
● The video heads may be dirty.
Use a dry cleaning cassette ECL-3F, or
consult your JVC dealer.
6. Breaks are noticeable in Hi-Fi
soundtrack.
● The automatic tracking mode is
engaged.
Try manual tracking. (੬ pg. 29)
Download from Www.Somanuals.com. All Manuals Search And Download.
84
EN
TROUBLESHOOTING (cont.)
PLAYBACK (DVD deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. The button do not work.
● The operation is prohibited on the
placed disc.
—
2. The DVD deck can not be operated.
● The DVD deck is not selected.
On the unit
Press VCR/DVD repeatedly so that the
DVD indicator lights up.
On the Remote
lights up.
3. “X” appears on the TV screen.
● The operation is prohibited on the
placed disc.
—
4. “REGION CODE ERROR!” appears on ● The disc’s region number does not
Use the discs whose region number
includes “ALL” or “1”. (੬ pg. 5)
the TV screen.
match that of the unit.
5. The disc cannot be played back.
● The disc’s region number does not
match that of the unit.
Use the discs whose region number
● This type of the disc cannot be played
back.
See “Unplayable Discs” (੬ pg. 5).
● The disc is not placed properly.
Remove the disc, then place the disc
properly in the disc tray. (੬ pg. 7,
“Placing a Disc”)
● The Parental Lock is engaged, and the
placed disc is rated higher than the set
level.
Release the Parental Lock temporarily
(੬ pg. 57).
6. The language is not played back as you ● The disc does not contain the language
—
set.
you set.
7. Changing audio/subtitle language is
not possible.
● The disc does not contain the audio/
subtitle in the multiple languages.
With some discs, the language should be
set on the top menu. (੬ pg. 41)
8. The subtitles do not appears on the TV ● The disc does not contain the subtitles.
—
screen.
● The subtitle display is set to off.
Set the subtitles display to on. (੬ pg. 52)
● A-B Repeat Playback is in progress.
(੬ pg. 49)
The subtitles recorded around A-B point
may not appear.
9. Angle cannot be changed.
● The scene is not recorded from the
multiple angles.
—
MP3/WMA Playback (DVD deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. A disc cannot be played.
● No MP3/WMA files are recorded to the Replace the disc.
disc.
● MP3/WMA files do not have the correct Add correct file extension (.mp3, .MP3 or
file extension in their file names.
any uppercase and lowercase combination
such as “.Mp3”) to their file names.
● MP3/WMA files are not recorded in a
Replace the disc. (Record MP3/WMA files
format compliant with ISO 9660 Level 1 using a compliant application.)
or 2.
● The different types of files are recorded
to the disc.
The disc which contains the different types
of files may not be played because of its
disc characteristics or recording
conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
85
2. Not MP3/WMA files but JPEG files are ● The MP3&WMA/JPEG setting is set to
When both MP3/WMA files and JPEG files
are recorded to a disc, set “MP3&WMA/
JPEG” to “MP3&WMA” to play MP3/WMA
files. (੬ pg. 79)
played.
“JPEG”.
3. The MP3/WMA control display
appears on the TV screen, but no
operation can be performed.
● No MP3/WMA files or JPEG files are
recorded to the disc, or the disc is an
unplayable disc (such as CD-ROM).
Replace the disc. (੬ pg. 7)
JPEG Playback (DVD deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. A disc cannot be played.
● No JPEG files are recorded to the disc.
Replace the disc.
● JPEG files do not have the correct file
extension in their file names.
Add correct file extension (.jpg, .jpeg,
.JPG, .JPEG or any uppercase and
lowercase combination such as “.Jpg”) to
their file names.
● JPEG files are not recorded in a format
compliant with ISO 9660 Level 1 or 2.
Replace the disc. (Record JPEG files using
a compliant application.)
2. Not JPEG files but MP3/WMA files are ● The MP3&WMA/JPEG setting is set to
played back. “MP3&WMA”.
When both MP3/WMA files and JPEG files
are recorded to a disc, set “MP3&WMA/
JPEG” to “JPEG” to play JPEG files.
(੬ pg. 79)
RECORDING (VCR deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Recording cannot be started.
● There is no cassette loaded, or the
Insert a cassette, or using adhesive tape,
cassette loaded has had its record safety cover the hole where the tab was
tab removed.
removed.
2. TV broadcasts cannot be recorded.
3. Tape-to-tape editing is not possible.
● “F-1” or “L-1” has been selected as the
Set to the desired channel.
input mode.
● The source (another video recorder,
camcorder) has not been properly
connected.
Confirm that the source is properly
connected.
● All necessary power switches have not
been turned on.
Confirm that all units’ power switches are
turned on.
● The input mode is not correct.
Set the input mode to “F-1” or “L-1”.
4. Camcorder recording is not possible.
● The camcorder has not been properly
connected.
Confirm that the camcorder is properly
connected.
● The input mode is not correct.
Set the input mode to “F-1” or “L-1”.
5. “⅜” and “$” on the front display
● The end of the tape was reached during The program may not have been recorded
panel won’t stop blinking.
recording.
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.
Download from Www.Somanuals.com. All Manuals Search And Download.
86
EN
TROUBLESHOOTING (cont.)
TIMER RECORDING (VCR deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Timer recording won’t work.
● The clock and/or the timer have been set Re-perform the clock and/or timer
incorrectly.
settings.
● The timer is not engaged.
Press TIMER and confirm that “#” is
displayed on the front display panel.
2. Timer programing is not possible.
● Timer recording is in progress.
Timer programing can’t be performed
while a timer recording is in progress.
Wait until it finishes.
3. “#” on the front display panel won’t
● The timer is engaged but there’s no
cassette loaded.
Load a cassette with the record safety tab
intact.
stop blinking.
4. “#”, “⅜” and “$” on the front
● The loaded cassette has had its record
safety tab removed.
Remove the cassette and cover the hole
with adhesive tape, or insert a cassette
with the record safety tab intact.
display panel won’t stop blinking.
● The end of the tape was reached during The program may not have been recorded
timer recording.
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.
5. “#” blinks for 10 seconds and the
● TIMER has been pressed when there are Check the programed data and re-
no programs in memory, or the timer program as necessary, then press TIMER
Timer mode is disengaged.
record information has been programed again.
incorrectly.
6. “⅜” and “$” on the front display
● The end of the tape was reached during The program may not have been recorded
panel won’t stop blinking.
Instant Timer Recording.
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.
7. “N”, “⅜” and “$” on the front display ● The loaded cassette has had its record
panel won’t stop blinking. safety tab removed.
Remove the cassette and cover the hole
with adhesive tape, or insert a cassette
with the record safety tab intact.
● The end of the tape was reached during The program may not have been recorded
Satellite Auto Recording.
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
87
OTHER PROBLEMS
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. The image of TV broadcast appears
distorted on the TV screen.
● The unit leaves turned on and the DVD Turn off the unit, or press VCR to select the
deck is selected.
VCR deck, then press TV/VCR so that the
VCR indicator disappears from the front
display panel.
2. Whistling or howling is heard from the ● The camcorder’s microphone is too
Position the camcorder so its microphone
is away from the TV.
TV during camcorder recording.
close to the TV.
● The TV’s volume is too high.
Turn the TV’s volume down.
3. When scanning channels, some of
them are skipped over.
● Those channels have been designated to If you need the skipped channels, restore
be skipped.
them. (੬ pg. 25)
4. The channel cannot be changed.
● Recording is in progress.
Press PAUSE (9) to pause the recording,
change channels, then press PLAY (4) to
resume recording.
5. Channel settings that were made
manually seem to have changed or
disappeared.
● After the manual settings were made,
Auto Channel Set was performed.
Perform manual setting again.
6. Even though Auto or Semiauto Clock
Set has been performed, the clock is
incorrect.
● The clock setting data received from the Select a different host channel during
host channel is incorrect.
“Semiauto Clock Set” (੬ pg. 23), or
perform “Manual Clock Set” (੬ pg. 23).
ATTENTION
This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the
unit off and unplug the AC power cord. Then plug it in again and turn the unit on. Take out the cassette. After checking the cassette,
operate the unit as usual.
Download from Www.Somanuals.com. All Manuals Search And Download.
88
EN
QUESTIONS AND ANSWERS
PLAYBACK
TIMER RECORDING
Q. What happens if the end of the tape is reached
during playback or search?
A. The tape is automatically rewound to the
beginning.
Q. “⅜” and “#” remain lit on the front display
panel. Is there a problem?
A. No. This is a normal condition for a timer
recording in progress.
Q. During search, slow, still and frame-by-frame
playback, I can’t hear any audio. What’s the
problem?
Q. Can I program the timer while I’m watching a
tape or a TV broadcast?
A. You won’t see the picture as it is replaced by the
on-screen menu, but the audio from the
program or tape you’re viewing can be heard.
A. This is normal.
Q. Can the unit indefinitely remain in the still
mode?
A. No. It stops automatically after 5 minutes to
protect the heads.
Q. When returning from search to normal
playback, the picture is disturbed. Should I be
concerned about this?
A. No, it is normal.
Q. Noise bar appear during search. What’s the
problem?
A. This is normal.
Q. Sometimes, during Index Search, the unit can’t
find the program I want to see. Why not?
A. There may be index codes too close together.
RECORDING
Q. When I pause and then resume a recording, the
end of the recording before the pause is
overlapped by the beginning of the
continuation of recording. Why does this
happen?
A. This is normal. It reduces distortion at the pause
and resume points.
Q. Can the unit indefinitely remain in the Record-
Pause mode?
A. No. The unit goes to its Stop mode
automatically after 5 minutes to protect the
heads.
Q. What happens if the tape runs out during
recording?
A. The unit stops recording, and “⅜” and “$” on
the front display panel won’t stop blinking.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
89
SPECIFICATIONS
GENERAL
TUNER
Power requirement : AC 110 V – 220 Vd , 50 Hz/60 Hz
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
: Frequency synthesized tuner
Power consumption
Power on
Power off
: 26 W
: 4.9 W
: Channels 2 – 13
: Channels 14 – 69
: 113 Channels
Temperature
Operating
Storage
: 5°C to 40°C
: –20°C to 60°C
: Channel 3 or 4 (switchable; preset
to Channel 3 when shipped)
75 ohms, unbalanced
Operating position : Horizontal only
Dimensions (WxHxD)
: 435 mm x 93 mm x 272 mm
: 4.4 kg
: S-VHS/VHS NTSC standard
TIMER
Weight
Format
Clock reference
: Quartz
Program capacity : 1-year programmable timer/
8 programs
Memory backup time
Maximum recording time
(SP)
(EP)
: 210 min. with ST-210 video cassette
: 630 min. with ST-210 video cassette
: Approx. 5 seconds
VIDEO/AUDIO (VCR deck)
Signal system : NTSC colour signal and EIA
monochrome signal, 525 lines/60
fields
Recording system : DA4 (Double Azimuth) head helical
scan system
Signal-to-noise ratio: 45 dB
Horizontal resolution
: 230 lines (VHS)
400 lines (S-VHS)
Frequency range : 70 Hz to 10,000 Hz (Normal audio)
20 Hz to 20,000 Hz (Hi-Fi audio)
ACCESSORIES
Provided accessories
: RF cable,
S-Video cable (4-pin),
Infrared remote control unit,
“AA” battery x 2,
Conversion plug
Specifications shown are for SP mode unless otherwise
specified.
E.& O.E. Design and specifications subject to change without
notice.
Input/Output
: RCA connectors:
IN x 2, OUT x 1
S-Video connectors:
IN x 2, OUT x1
VIDEO/AUDIO (DVD deck)
Signal system
Applicable disc
: NTSC
: DVD (12 cm, 8 cm)
CD (12 cm, 8 cm)
Audio characteristics
DVD
: 4 Hz – 22 KHz
Frequency response
CD
: 4 Hz – 20 KHz
: 90 dB
Harmonic distortion
S/N Ratio
: 0.1 %
Wow and flutter
Dynamic range
Output
: Below Measurable Level
: 90 dB
Component-Y : (RCA) 1.0 Vp-p/75 ohm
Component-P /P
B
R
: (RCA) 0.7 Vp-p/75 ohm
: (RCA) 2 Vrms, 1 Kohm
Audio
Digital Audio : (COAXIAL) 0.5 Vp-p/75 ohm
(OPTICAL) –21 dBm to –15 dBm
(peak)
Download from Www.Somanuals.com. All Manuals Search And Download.
90
EN
LIST OF TERMS
A
J
A-B Repeat Playback ............................................ 49
About Discs
L
JPEG .............................................................. 63
MP3/WMA ..................................................... 60
Placing a Disc .................................................. 7
Playable Discs .................................................. 5
Region Number ................................................ 5
Unplayable Discs .............................................. 5
Angle Selection .................................................... 53
Audio Channel Selection ....................................... 55
Audio Language Selection ..................................... 54
Auto Channel Set ................................................. 24
(DVD deck only) ........................................20
On-screen Language Set (DVD deck) .................19
On-screen Language Set (VCR deck) ..................18
M
Manual Clock Set .................................................23
Mode Set (DVD deck)
C
Chapter Search .................................................... 50
Check, cancel and change programs ....................... 36
Child Lock .......................................................... 82
Clock Set ............................................................ 22
Component Video Connection ............................... 14
Connecting To A Dolby Digital Decoder or
ANALOG DOWN MIX .....................................80
MENU LANGUAGE .........................................20
MONITOR TYPE ....................................... 17, 79
MP3&WMA/JPEG ............................................79
ON SCREEN GUIDE ........................................81
OUTPUT LEVEL ..............................................80
PICTURE SOURCE ..........................................79
SCREEN SAVER ...............................................79
SUBTITLE .......................................................20
Mode Set (VCR deck)
AUTO POWER OFF ........................................77
AUTO SP]EP TIMER ......................................75
SUPERIMPOSE ................................................75
S-VHS ET .......................................................74
S-VHS MODE .................................................77
VIDEO CALIBRATION ............................... 33, 74
VIDEO STABILIZER .........................................75
Monitor Set (DVD deck)
An Amplifier With A Built-in DTS ...................... 72
D
Digital Audio Dubbing .......................................... 69
Disc menu .......................................................... 41
Dubbing (from DVD to VCR) ................................. 68
E
EDITING (DVD DECK)
Digital Audio Dubbing ..................................... 69
EDITING (VCR DECK)
Dubbing (from DVD to VCR) ............................ 68
Edit From A Camcorder .................................... 66
Edit To Or From Another Video Recorder ........... 67
Elapsed Recording Time Indication ......................... 32
Express Timer Programing ..................................... 34
G
Group/file selection .............................................. 65
Group/track selection ........................................... 62
I
INDEX .................................................................. 8
Index Search ........................................................ 28
Instant ReView ..................................................... 28
Instant Timer Recording (ITR) ................................. 31
MONITOR TYPE ....................................... 17, 79
MP3/WMA control display .....................................60
N
Next Function Memory .........................................29
O
OPERATIONS ON DVD DECK ........................40 – 65
OPERATIONS ON VCR DECK .........................26 – 39
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
91
P
T
Pan&Scan ........................................................... 17
Parental Lock
Country/Area Code List .................................... 58
To change the settings ..................................... 57
To set Parental Lock for the first time .................. 56
To temporarily release the Parental Lock ............ 57
Playback (DVD deck) .................................... 40 – 65
Playback (JPEG) ............................................ 64 – 65
Playback (MP3/WMA) .................................... 61 – 62
Playback (VCR deck) ..................................... 26 – 29
Playback Control (PBC) Function .......................41, 49
Plug&Play Set ...................................................... 15
Program Playback ................................................ 51
V
Variable Speed Search ..................................... 27, 42
VFP function ........................................................45
W
Z
R
Random Playback ................................................ 51
Recording .................................................... 30 – 33
Recording Resume Function .................................. 30
Region Number ..................................................... 5
Remote Control Functions ..................................... 70
Repeat Playback ................................. 29, 48, 62, 65
Resume Function ................................................. 43
S
Satellite Auto Recording ........................................ 39
Scan Mode Set (DVD deck) ................................... 82
Second Audio Recording ....................................... 32
Semiauto Clock Set ............................................... 23
Skip Search ......................................................... 28
Slow Motion ...................................................27, 43
Soundtrack Selection ............................................ 29
Still Picture/Frame-By-Frame Playback ...............27, 43
Subtitle Selection ................................................. 52
S-VHS ................................................................. 67
S-VIDEO Connection ............................................ 13
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Printed in Beijing
0903-TY-ID-BJ
Download from Www.Somanuals.com. All Manuals Search And Download.
|