DVD/CD RECEIVER
KD-DV6108
KD-DV6108
For canceling the display demonstration, see page 11.
INSTRUCTIONS
GET0380-001A
[UL]
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS:
This product incorporates copyright
protection technology that is protected
by U.S. patents and other intellectual
property rights. Use of this copyright
protection technology must be authorized
by Macrovision, and is intended for home
and other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
• DO NOT install any unit in locations
where;
– it may obstruct the steering wheel and
gearshift lever operations, as this may
result in a traffic accident.
– it may obstruct the operation of safety
devices such as air bags, as this may
result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while
manipulating the steering wheel, as this
may result in a traffic accident.
• The driver must not watch the monitor
while driving.
If the driver watches the monitor while
driving, it may lead to carelessness and
cause an accident.
• The driver must not put on the
headphones while driving. It is
dangerous to shut off the outside sounds
while driving.
Caution on volume setting:
Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.
• If you need to operate the unit while
driving, be sure to look ahead carefully
or you may be involved in a traffic
accident.
• If the parking brake is not engaged,
“DRIVER MUST NOT WATCH THE
MONITOR WHILE DRIVING.”
appears on the monitor, and no
playback picture will be shown.
– This warning appears only when the
parking brake wire is connected to the
parking brake system built in the car
(refer to the Installation/Connection
Manual).
For safety....
Temperature inside the car....
• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.
• Stop the car before performing any
complicated operations.
If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating the
unit.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
How to read this manual
How to use the M MODE button
If you press M MODE, the unit goes into
functions mode, then the number buttons and
5/∞ buttons work as different function buttons.
The following methods are used to make the
explanations simple and easy-to-understand:
• Some related tips and notes are explained in
“More about this unit” (see pages 46 – 49).
• Button operations are mainly explained with
the illustrations as follows:
Ex.: When number button 2 works as
MO (monaural) button.
Press briefly.
Press repeatedly.
Press either one.
Time countdown indicator
To use these buttons for original functions
again after pressing M MODE, wait for
5 seconds without pressing any of these buttons
until the functions mode is cleared.
• Pressing M MODE again also clears the
functions mode.
Press and hold until
your desired response
begins.
Press and hold both
buttons at the same
time.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
How to reset your unit ...........................
How to forcibly eject a disc...................
How to read this manual........................
How to use the M MODE button...........
2
2
4
4
Other disc operations ..................... 29
Basic operations..................................... 29
Changing the display information ......... 30
Selecting the playback modes................ 31
Introduction — Playable discs............ 6
Dual Zone operations ..................... 32
Listening with headphones.................... 32
Control panel ................................ 7
Parts identification.................................
7
Sound adjustments......................... 33
Selecting preset sound modes ...... 33
Storing your own sound adjustments..... 33
Adjusting the sound............................... 34
Remote controller — RM-RK230 ....... 8
Main elements and features ...................
8
Getting started.............................. 10
Basic operations............................. 10
Canceling the display demonstrations... 11
Setting the clock .................................... 11
General settings — PSM................ 35
Basic procedure ..................................... 35
Other main functions...................... 37
Assigning titles to the sources ............... 37
Detaching the control panel................... 38
Radio operations............................ 12
Listening to the radio.................... 12
Storing stations in memory.................... 13
Listening to a preset station................... 14
CD changer operations.................... 39
Playing discs in the CD changer.... 39
Changing the display information ......... 41
Selecting the playback modes................ 42
Disc operations .............................. 15
Playing a disc in the unit .............. 15
Basic operations .................................... 17
External component operations............ 43
Playing an external component.... 43
DVD/VCD special functions ............ 19
Selecting subtitles.................................. 19
Selecting audio languages ..................... 19
Selecting multi-angle views................... 19
Disc menu operations ............................ 20
Zoom in.................................................. 20
Maintenance.................................. 44
Language codes.............................. 45
More about this unit....................... 46
Troubleshooting ............................. 50
Specifications................................. 53
On-Screen disc operations............... 21
Basic on-screen bar operations.............. 22
Basic control screen operations ............. 24
List screen operations............................ 25
DVD setup menu ............................ 26
Basic setting procedure.......................... 26
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction — Playable discs
Discs you can play
Caution for DualDisc playback
You can play back the following discs (12 cm
and 8 cm) on this unit:
• DVD Video: Recorded in either PAL or
NTSC color system with Region Code “3”
(see below).
• The Non-DVD side of a “DualDisc” does
not comply with the “Compact Disc Digital
Audio” standard. Therefore, the use of Non-
DVD side of a DualDisc on this product may
not be recommended.
– DVD-R/DVD-RW recorded in the DVD-
Video format can also be played (see page
46).
• Video CD (VCD)/audio CD
• MP3/WMA: Recorded either in CD-R/
CD-RW or DVD-R/DVD-RW/DVD-ROM.
– CD-R/CD-RW: Compliant with ISO 9660
Level 1, ISO 9660 Level 2, Romeo, and
Joliet.
Digital audio formats
The System can play back the following digital
audio formats.
Linear PCM: Uncompressed digital audio,
the same format used for CDs and most studio
masters.
Dolby Digital *2: Compressed digital audio,
developed by Dolby Laboratories, which
enables multi-channel encode to create the
realistic surround sound.
– DVD-R/DVD-RW/DVD-ROM: Compliant
with UDF-Bridge Format*1.
On some discs, the actual operations may be
different from what is explained in this manual.
DTS *3 (Digital Theater Systems):
Compressed digital audio, developed by Digital
Theater Systems, Inc., which enables multi-
channel like Dolby Digital. As the compression
ratio is lower than for Dolby Digital, it provides
wider dynamic range and better separation.
Discs cannot be played back
DVD-Audio, DVD-ROM (data), DVD-RAM,
DVD-R/DVD-RW recorded in the DVD-VR
format, CD-ROM, CD-I (CD-I Ready), Photo
CD, etc.
• Playing back these discs will generate noise
and damage the speakers.
MPEG Audio: Another compressed digital
audio which also enables multi-channel encode
to create the realistic surround sound. However,
this System downmix the multi-channel signals
into 2 channels (decoded PCM) and play it
back.
Note on Region Code:
DVD players and DVD Video discs have
their own Region Code numbers. This unit
can only playback DVD discs whose Region
Code numbers include “3.”
*1 A hybrid file system used to provide
compatibility with ISO 9660 for accessing
any type of files on the disc. (UDF stands for
Universal Disk Format.)
*2 Manufactured under license from
Dolby Laboratories. “Dolby” and the
double-D symbol are trademarks of Dolby
Laboratories.
Examples:
*3 “DTS” and “DTS 2.0 + Digital Out” are
trademarks of Digital Theater Systems, Inc.
If you insert a DVD Video disc of an
incorrect Region Code
“REGION CODE ERROR!” appears on the
monitor.
“DVD Logo” is a trademark of DVD Format/
Logo Licensing Corporation registered in the
US, Japan and other countries.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
Parts identification
Display window
1 5 (up) / ∞ (down) buttons
Display window
a Disc information indicators—
• Function as Play / Stop buttons for DVD
and VCDs.
TAG (ID3 Tag),
(folder),
(track/file)
2 E EQ (equalizer) button
3 D DISP (display) button
4 S SEL (select) button
5 • Control dial
s Main display
d Source display / Volume level indicator
f EQ (equalizer) indicator
g Sound mode indicators—ROCK,
CLASSIC, POPS, HIP HOP, JAZZ, USER
•
(standby/on attenuator) button
6 Display window
7 Remote sensor
8 0 (eject) button
•
also works as the time countdown
indicator and level meter during play
(see page 35).
h Disc type indicators—WMA, MP3
j Tuner reception indicators—
ST (stereo), MO (monaural)
9
p
4/¢
(control panel release) button
buttons
q SOURCE button
k Playback source indicators—
CH: Lights up for the CD changer.
DISC: Lights up for the built-in DVD/CD
player.
w BAND button
e Number buttons
r MO (monaural) button
t SSM (Strong-station Sequential Memory)
button
y DUAL (dual zone) button
u RPT (repeat) button
i RND (random) button
o M MODE button
l Playback mode / item indicators—
RND (random),
RPT (repeat)
(disc),
(folder),
/ LOUD (loudness) indicator
z Tr (track) indicator
;
AUX (auxiliary) input jack
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote controller — RM-RK230
Installing the lithium coin battery
(CR2025)
Main elements and features
MONITOR CONTROL
MODE
ASPECT
MENU
DVD / RECEIVER CONTROL
ZOOM
ATT
+10
SOURCE
BAND
–100
+100
PRESET
/ TITLE
–10
/ TITLE
DUAL
VOL
OSD
3
1
2
5
+
DISC
TOP M
MENU
6
4
2nd VOL
ENTER
7
8
0
9
–
DISC
SETUP
RETURN
Before using the remote controller:
SHIFT
• Aim the remote controller directly at the
remote sensor on the unit. Make sure there is
no obstacle in between.
RM-RK230
Remote sensor
IMPORTANT:
If Dual Zone is activated (see page 32),
the remote controller only functions for
operating the DVD/CD player.
• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Warning:
MONITOR CONTROL
• Do not install any battery other than
CR2025 or its equivalent; otherwise, it
may explode.
• Store the battery in a place where children
cannot reach to avoid risk of accident.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, or
heat the battery, or dispose of it in a fire.
– Do not leave the battery with other
metallic materials.
1 Monitor control buttons*1
•
(standby/on), MODE, ASPECT,
MENU, and
.
DVD/RECEIVER CONTROL
(standby/on attenuator) button
2
• Turns on and off the power and also
attenuates the sound.
3 SOURCE button
• Selects the source.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate
when throwing away or saving it.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BAND button
t RETURN button*2
• Selects the FM/AM bands.
5 TOP M (menu) button*2
• Display the DVD and VCD*3 disc menu.
6 DUAL button
y Special function buttons
• DVD/VCD:
(audio)
• DVD: (subtitle),
(angle)
• Activate and deactivate Dual Zone.
7 VOL + / – buttons
• Adjusts the volume level.
• Also function as 2nd VOL +/– buttons
when pressed with SHIFT button.
8 SETUP button*2
*1 Controllable only if your monitor is one of
the JVC monitors — KV-MR9010 or
KV-MH6510.
*2 These buttons function as the number
buttons when pressed with SHIFT button.
*3 Only when PBC is not in use.
*4 Not used for CD changer operations.
*5 These buttons function as the +10/–10
and +100/–100 buttons when pressed with
SHIFT button.
9 SHIFT button
p Basic disc operation buttons*4
7 (stop), 3 (play), 8 (pause)
• 3 (play) also function as ZOOM button
when pressed with SHIFT button.
q Advanced disc operation/tuner operation
buttons*5
For advanced disc operations:
•
/TITLE 5 / ∞ — Select the titles (for
DVD) or folders (for MP3/WMA).
How to select a number
To select a number from 0 – 9:
• 4 / ¢ (reverse skip/forward skip)
• 1 / ¡ (reverse search/forward
search)*4
For tuner operations:
• PRESET 5 / ∞ — Changes the preset
stations.
• 4 / ¢ — Functions to search for
stations.
w OSD button
To select a number greater than 9:
• Display the on-screen bar.
• Also function as the /TITLE button
when pressed with SHIFT button.
–You can directly select titles (for DVD)
or folders (for MP3/WMA) using the
number buttons (see page 18).
e MENU button*2
• Display the DVD and VCD*3 disc menu.
r Menu operation buttons*2
• Cursor (% , fi , @ , #), and ENTER
• % / fi : Also function as DISC + / –
buttons when the source is “CD-CH.”
• +100/–100 buttons used only for searching
MP3/WMA tracks number greater than 99.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Basic operations
~
Ÿ
@
Adjust the sound as you want.
(See pages 33 and 34.)
To drop the volume in a moment (ATT)
To restore the sound,
press it again.
You cannot select some sources if they
are not ready.
To turn off the power
!
⁄
For FM/AM tuner only
Adjust the volume.
Volume level appears.
Volume level indicator
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling the display
demonstrations
If no operations are done for about 20 seconds,
display demonstration starts.
Setting the clock
1
[Initial: DEMO ON]—see page 35.
2 Set the hour and minute.
1 Select “CLOCK H” (hour), then
adjust the hour.
1
2
2 Select “CLOCK M” (minute),
then adjust the minute.
3
3 Finish the procedure.
To check the current clock time when the
power is turned off
4 Finish the procedure.
To activate the display demonstration
In step 3 above...
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio operations
Listening to the radio
To tune in to a station manually
In step ! on the left column...
1
~
Ÿ
Selected band appears.
2 Select the desired station frequencies.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
!
Start searching for a station.
When a station is received, searching
stops.
To stop searching, press the same
button again.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
When an FM stereo broadcast is hard to
receive
1
Storing stations in memory
You can preset six stations for each band.
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
2
1
2 Select the FM band (FM1 – FM3)
Lights up when monaural mode is activated.
you want to store into.
Reception improves, but stereo effect will
be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO
indicator goes off.
3
4
“SSM” flashes, then disappears when
automatic presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.
To be continued....
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual presetting
Ex.:Storing FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
Listening to a preset station
1
2
1
2
3
3 Select the preset station (1 – 6) you
want.
or
4
When using the remote controller....
or
Preset number flashes for a while.
To check the current clock time while
listening to an FM or AM station
* If no title is assigned to a station, “NO
NAME” appears. To assign a title to a
station, see page 37.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc operations
Playing a disc in the unit
The disc type is automatically detected, and
playback starts automatically (for DVD:
automatic start depends on its internal program).
Before performing any operations, make
sure the following....
• To watch the playback pictures, select the an
appropriate video system (NTSC or PAL) to
match it to the connected monitor. (See page
36.)
• Turn on the monitor for playing a DVD or
VCD. If you turn on the monitor, you can also
control the audio CD, CD Text, and MP3/
WMA playback by referring to the monitor
screen. (See pages 24 and 25.)
If the current disc is an audio CD, CD Text,
MP3/WMA, or VCD without PBC, all tracks
will be played repeatedly until you change the
source or eject the disc.
• If a title list or disc menu appears while
playing a DVD or VCD with PBC, see “Disc
menu operations” on page 20.
• For DVD playback, you can change the Setup
Menu setting to your preference. (See pages
26 – 28.)
The following marks are used to indicate
the playable discs....
• The operations explained on pages 17 – 28 are
using the remote controller.
• When you want to operate the DVD/CD
player using the buttons on the control panel,
see “Other disc operations” on pages 29 – 31.
DVD Video
Video CD with PBC
only
If “ ” appears on the monitor when
pressing a button, the unit cannot accept an
operation you have tried to do.
• In some cases, without showing “ ,”
operations will not be accepted.
Video CD with/without
PBC
Audio CD/
CD Text
MP3/WMA disc
All discs listed here
To be continued....
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• When inserting a DVD disc:
• When inserting a VCD:
Total title number
Total playing time
Total track number
of the inserted disc of the inserted disc
Elapsed playing time
Elapsed playing
time
Current chapter number
• When inserting an MP3/WMA disc:
• When inserting a CD Text/audio CD:
Total folder number
Total playing time
Total track number
of the inserted disc of the inserted disc
Total track number
CD Text: Disc title/performer =
Track title appears automatically
(see page 30).
Ex.: When an MP3 file is detected
Current track
number
Elapsed playing
time
Disc information appears
automatically (see page 30).
Elapsed playing Current track
time
number
To eject the disc
Current folder number
*1 Either the MP3 or WMA indicator lights up
depending on the detected file.
*2 Does not light up for DVD-R/DVD-RW.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
Operations
Display indication and/or next operation
To stop play temporarily
“PAUSE” illuminates on the display.
A still picture appears.
A Frame by frame playback
B Slow motion playback
• No sound comes out during Slow Motion Playback.
• When playing a VCD, Reverse Slow Motion Playback is
prohibited.
To resume normal play:
To replay the previous
The playback position moves back about 10 seconds before
scenes—One Touch Replay the current position.
• This function works only within the same title.
• For some DVDs, this function does not work.
To stop playback
When you start playback again, playback
starts from where it has been stopped
(Resume play).
When you start playback again, playback starts from
the beginning of the last playing track.
* During play, on-screen guide icons appear on the monitor for a while (see page 48).
To be continued....
17
Download from Www.Somanuals.com. All Manuals Search And Download.
To go to the next or previous
chapters/tracks
To locate a particular title/chapter/
track directly
• For DVD: During play or pause
• For DVD: During play or pause—select a
chapter.
During stop—select a title.
• For VCD: While PBC (see page 20) is not
in use.
To the following
chapters/tracks.
• For MP3/WMA: Select a track within the
same folder.
To go back to the beginning of the current
chapter/track, then the previous chapters/tracks.
Select the number corresponding to the item
you want (see page 9).
To fast-forward or reverse
the chapter/track
To locate a title/folder
Fast-forwards.
To the next title/folder.
Reverses.
To the previous title/folder.
* The search speed changes to x2 ] x10 for all
discs (DVD, VCD, CD), but the information
shown on the monitor is only for DVD/VCD.
To locate a particular title/folder
To forward or reverse
search the chapter/track
Within 10 seconds,
press the number
The information shown is only for DVD/VCD:
buttons (see page 9).
• To resume normal speed
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD/VCD special functions
For VCD:
You can select the audio channel to
play. (This is convenient when playing a
Karaoke VCD.)
Selecting subtitles
You can select the language of the subtitle
to be shown on the monitor.
• You can set the initial subtitle language
using the setup menu (see page 27).
ST
ST
1/3
ENGLISH
1/3
ST: To listen to normal stereo (left/right)
ENGLISH
playback.
L: To listen to the L (left) audio channel.
R: To listen to the R (right) audio channel.
Ex.: When the disc has 3 options
Selecting audio languages
For DVD:
Selecting multi-angle views
You can select the language to listen to if
the disc has multiple audio languages.
You can view the same scene at different
angles if the disc has multi-angle views.
1/3
1
1/3
1/3
ENGLISH
1/3
1
ENGLISH
1/3
1/3
1
2
Ex.: When the disc has 3 options
1/3
3
Ex.: When the disc has 3 multi-angle views
• For some DVDs and VCDs, changing the
subtitle language, audio language (or audio
channel) without using the disc menu is
prohibited.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling the PBC playback
1
Disc menu operations
Menu-driven playback is possible while playing
back a DVD with menu-driven features or a
VCD with the PBC (PlayBack Control).
2 Select a track to start normal playback using
the number buttons (see page 9).
While playing a DVD
To resume the PBC function
1
A title list or disc menu will appear on the
monitor.
Zoom in
2 Select the item you want on the
menu.
1
Selected item starts playback.
• On some discs, you can also select items
using the corresponding number buttons.
ZOOM 1
ZOOM 2
ZOOM 6
ZOOM 3
ZOOM 4
ZOOM OFF
ZOOM 5
While playing a VCD
• When a list of items is displayed on the
2 Move the zoomed-in portion.
monitor.
To cancel zoom, select “ZOOM OFF” in
step 1.
• To select a number greater than 9, see “How
to select a number” on page 9.
To return to the previous menus
20
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen disc operations
1 Disc type
2 • Audio signal format type (for DVD and
DTS audio CD)
• PBC (only for VCD)
3 Playback information
About the On-Screen Bar
You can check the disc information and use
some functions through the on-screen bar.
• For audio CD, CD Text, and MP3/WMA
disc you can also use the control screen
and list screen (see pages 24 and 25).
Current track/chapter
Current track
T02-C03
TRACK 01
TOTAL
Elapsed playing time of the disc
T. REM
Remaining disc time (for VCD)/
remaining title time (for DVD-V)
On-Screen bars
TIME
Elapsed playing time of the
current chapter/track
DVD
REM
Remaining time of the current
chapter/track
4 Playback condition
2ch
T02-C03 TOTAL 1:25:58
DVD-V
TIME
TITLE
CHAP
OFF
Playback
Forward/reverse search
Forward/reverse slow-motion
Pause
VCD
Stop
5 Operation icons
PBC
TRACK 01 TIME
REPEAT INTRO RANDOM
00:36
VCD
TIME
Time indication
TIME
TRACK
Time Search—Enter the elapsed
playing time of the current title
or of the disc.
Title Search
Chapter Search
Track Search
Change the audio language or
audio channel.
MP3/WMA
TITLE
CHAP
TRACK
TIME 00:00:36
FILE
REPEAT INTRO RANDOM
Change the subtitle language.
Change the view angle.
Repeat play (for DVD)
Repeat play (for other discs)
Intro play
CD Text/audio CD
OFF
REPEAT
INTRO
TIME
00:36
5. 1ch
CD
RANDOM
REPEAT INTRO RANDOM
Random play
* Only for DTS audio CD
To be continued....
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To erase the on-screen bar
Basic on-screen bar operations
1 Display the on-screen bar.
• For DVD/VCD:
• The selectable options for Repeat/Intro/
Randam plays:
(twice)
Repeat play
OFF
• For other discs:
DVD:
OFF
CHAP
TITLE
2ch
T02-C03 TOTAL 1:25:58
DVD-V
TIME
TITLE
CHAP
OFF
REPEAT
Repeat play
2 Select an item.
VCD (while PBC is not in use):
REPEAT
(Canceled)
MP3/WMA:
3 Make a selection.
REPEAT TRACK
REPEAT FOLDER
(Canceled)
CD Text/audio CD:
• If pop-up menu appears...
1
(Canceled)
REPEAT TRACK
2ch
T02-C03 TOTAL 1:25:58
DVD-V
TIME
TITLE
CHAP
OFF
_ _
or
2
22
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRO
Intro play
To search for a particular point by playing
time
VCD (while PBC is not in use):
1 Select
.
INTRO
(Canceled)
2 Enter the elapsed playing time of the current
title or of the disc.
MP3/WMA:
INTRO TRACK
INTRO FOLDER
(Canceled)
CD Text/audio CD:
Ex.: • To enter 1 (hours): 02 (minutes): 00
(seconds), press 1, 0, 2, 0, then 0.
• To enter 54 (minutes): 00 (seconds),
press 0, 5, 4, 0, then 0.
(Canceled)
INTRO TRACK
RANDOM
Random play
• It is always required to enter the hour
digit (even “0” hour), but it is not
required to enter trailing zeros (the last
two digits in the examples above).
• To correct a misentry, press...
VCD (while PBC is not in use):
RANDOM
(Canceled)
MP3/WMA:
RANDOM FOLDER
RANDOM DISC
(Canceled)
3 Finish the procedure.
CD Text/audio CD:
(Canceled)
RANDOM DISC
To search for a particular title/chapter/
track
TITLE
CHAP
TRACK
1 Select
,
, or
.
2 Enter the number.
Refer also page 22 for the following operations.
To change the time information
TIME
1 Select
.
2 Change the time information.
• To correct a misentry, press the number
button until the correct number is entered.
REM 0:11:23
TOTAL 1:01:58
TIME 0:00:58
T. REM 0:35:24
3 Finish the procedure.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
To select a folder or track
1 Select “Folder” column or “Track” column
Basic control screen operations
You can search for and play the desired items
through the control screen.
on the control screen.
• The control screen automatically appears on
the monitor when you insert a disc.
2 Select a folder or track.
MP3/WMA control screen
REPEAT TRACK TIME 00:00:14
FOLDER : 2 / 3
Track : 5 / 14 (Total 41)
01 Music
02 Music
03 Music
Cloudy.mp3
Fair.mp3
Fog.mp3
Hail.wma
Indian summer.mp3
Rain.mp3
Shower.mp3
Snow.mp3
Thunder.wma
Typhoon.mp3
Wind.mp3
CD Text/audio CD control
screen
Track Information
Album
Weather
Artist
Robert M. Smith
Title
Rain
TIME
00:14
Track : 5 / 14
Cloudy
Fair
Fog
Winter sky.mp3
Hail
Indian summer
Rain
Shower
Snow
Thunder
Typhoon
Wind
Track Information
Album
Four seasons
Artist
Robert M. Smith
Title
1 Current folder
2 Current folder number/total folder number
3 Folder list
Rain
Winter sky
4 Selected playback mode
5 Elapsed playing time of the current track
6 Operation mode icon
‰ (play), 7 (stop), 8 (pause)
7 Current track number/total number of tracks
in the current folder (total number of tracks
on the disc)
8 Track information
9 Track list
p Current track (highlighted bar)
1 Elapsed playing time of the current track
2 Operation mode icon
‰ (play), 7 (stop), 8 (pause), ¡ (fast-
forward), 1 (reverse)
3 Current track number/total number of tracks
on the disc
4 Track information
5 Track list
6 Current track (highlighted bar)
To select a track
24
Download from Www.Somanuals.com. All Manuals Search And Download.
For MP3/WMA:
List screen operations
While stop....
You can display the folder list/track list before
starting play. On this list, you can confirm the
contents and start playing a disc.
1 Display the folder list.
Each time you press the button,
the list screen comes on and
goes off.
Folder/track list screens
Folder list (MP3/WMA)
2 Select a folder on the list.
Folder : 153/240 Track 154/198
Page : 4/6
fol140
fol141
fol142
fol143
fol144
fol145
fol146
fol147
fol148
fol149
fol150
fol151
fol152
fol153
fol154
fol155
fol156
fol157
fol158
fol159
fol160
fol161
fol162
fol163
fol164
fol165
fol166
fol167
fol168
fol169
fol130
fol131
fol132
fol133
fol134
fol135
fol136
fol137
fol138
fol139
The track list of the selected folder appears.
To go back to the folder list
3 Select a track on the list.
Track list (MP3/WMA/CD Text/audio CD)
Folder : 153/240 Track 154/198
Page : 4/6
file0161.wma
file0162.mp3
file0163.wma
file0164.mp3
file0165.wma
file0166.wma
file0167.wma
file0168.wma
file0169.mp3
file0170.wma
file0131.mp3 file0141.mp3 file0151.wma
file0132.mp3 file0142.mp3 file0152.mp3
file0133.wma file0143.mp3 file0153.wma
file0134.mp3 file0144.mp3 file0154.mp3
file0135.mp3 file0145.wma file0155.mp3
file0136.wma file0146.mp3 file0156.mp3
file0137.wma file0147.wma file0157.mp3
file0138.mp3 file0148.mp3 file0158.wma
file0139.mp3 file0149.wma file0159.wma
file0140.wma file0150.wma file0160.wma
For CD Text/audio CD:
While stop....
1 Display the track list.
Each time you press the button,
the list screen comes on and
goes off.
Ex.: Track list for MP3/WMA
2 Select a track on the list.
1 Current folder number/total folder number
(only for MP3/WMA)
2 Current track number/total number of tracks
in the current folder
3 Current page/total number of the pages
included in the list
4 Current folder/track (highlighted bar)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD setup menu
You can store the initial disc playback status.
• While playing, no change can be made on the
setup menu.
4
AUDIO
DIGITAL AUDIO OUTPUT
STREAM/PCM
Basic setting procedure
DOWN MIX
STEREO
DOLBY SURROUND
STEREO
ON
D. RANGE COMPRESSION
While stop...
1
5 Select an option.
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
ENGLISH
ENGLISH
AUDIO
ON SCREEN LANGUAGE
DIGITAL AUDIO OUTPUT
DOWN MIX
STREAM/PCM
STEREO
DOLBY SURROUND
STEREO
ON
D. RANGE COMPRESSION
2
6
AUDIO
AUDIO
DIGITAL AUDIO OUTPUT
DOWN MIX
STREAM/PCM
STEREO
ON
DIGITAL AUDIO OUTPUT
DOWN MIX
STREAM/PCM
DOLBY SURROUND
ON
D. RANGE COMPRESSION
D. RANGE COMPRESSION
Ex.: When selecting the “AUDIO” menu
To set other items on the same menu
Repeat steps 3 to 6.
3 Select an item you want to set up.
To set other items on other menus
Repeat steps 2 to 6.
AUDIO
DIGITAL AUDIO OUTPUT
DOWN MIX
STREAM/PCM
STEREO
ON
To return to the normal screen
D. RANGE COMPRESSION
Ex.: When selecting “DOWN MIX”
26
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE menu
Item
Contents
Select the initial disc menu language.
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
Select the initial audio language.
Select the initial subtitle language or erase the subtitle (OFF).
Select the language for the Setup menu and some indications shown on
the monitor.
ON SCREEN LANGUAGE
• For the LANGUAGE settings, see also the language codes list on page 45.
PICTURE menu
Item
Contents
Select the monitor type to watch a wide screen picture on your
monitor.
• 16:9 [MULTI]* : Select this when the aspect ratio of your
monitor is 16:9.
MONITOR TYPE
16:9
4:3 LETTER BOX
• 4:3 [MULTI]* LETTER BOX : Select this when the aspect
ratio of your monitor is 4:3. While viewing a wide screen
picture, the black bars appear on the top and the bottom of the
screen.
4:3 PAN SCAN
• 4:3 [MULTI]* PAN SCAN : Select this when the aspect
ratio of your monitor is 4:3.
While viewing a wide screen picture, the black bars do not
appear; however, the left and right edges of the pictures will
not be shown on the screen.
* Select [MULTI] options for the multi-color system TVs.
Select the on-screen bar position on the monitor.
• 1 : Higher position
• 2 : Lower position
OSD POSITION
Position 1
Position 2
To be continued....
27
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO menu
Item
Contents
Select the signal format to be emitted through the DIGITAL OUT
(Optical) terminal on the rear. For details, see page 49.
• PCM ONLY : Select this when connecting an amplifier or a
decoder incompatible with Dolby Digital, DTS, MPEG Audio, or
connecting to a recording device.
DIGITAL AUDIO OUTPUT
• DOLBY DIGITAL/PCM : Select this when connecting an
amplifier or a decoder compatible with Dolby Digital.
• STREAM/PCM : Select this when connecting an amplifier or a
decoder compatible with Dolby Digital, DTS, and MPEG Audio.
When playing back a multi-channel DVD disc, this setting affects
the signals reproduced through the LINE OUT jacks (and through
the DIGITAL OUT terminal when “PCM ONLY” is selected for
“DIGITAL AUDIO OUTPUT”).
DOWN MIX
• DOLBY SURROUND : Select this when you want to enjoy multi-
channel surround audio by connecting an amplifier compatible with
Dolby Surround to this unit.
• STEREO : Normally select this.
You can enjoy a powerful sound at low or middle volume levels while
playing a Dolby Digital software.
D.RANGE COMPRESSION
• AUTO : Select this to apply the effect to multi-channel encoded
software (excluding 1-channel and 2-channel software).
• ON : Select this to always use this function.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Other disc operations
In this section, you can learn how to use the
buttons on the control panel in order to operate
the DVD/CD player.
To go to the next or previous folders
To next folders.
Basic operations
To previous folders.
To stop playback
To locate a particular title/chapter/
folder/track directly
To start playback again
To eject a disc
• For DVD: During play or pause—select a
chapter.
During stop—select a title.
• For VCD: While PBC (see page 20) is
not in use.
To select a number from 1 – 6:
To fast-forward or
reverse the chapter/track
To select a number from 7 – 12:
Fast-forwards.
Reverses.
• The number buttons can also use to select
item on the PBC menu.
• To use folder search on MP3/WMA discs, it
is required that folders are assigned with
2-digit number at the beginning of their folder
names—01, 02, 03, and so on.
* The search speed changes to x2 ] x10 for all
discs (DVD, VCD, CD), but the information
shown on the monitor is only for DVD/VCD.
To go to the next or previous
chapters/tracks
• To select a particular track in a folder (for
MP3/WMA disc) after selecting a folder:
For DVD: During play or pause
To the following tracks.
To the beginning of the current track, then the
previous tracks.
To be continued....
29
Download from Www.Somanuals.com. All Manuals Search And Download.
To go to a chapter/track quickly
Prohibiting disc ejection
You can lock a disc in the loading slot.
• For DVD: During play or pause.
• For VCD: While PBC (see page 20) is not
in use.
• For MP3/WMA: Select a track within the
same folder.
1
2
To cancel the prohibition, repeat the same
procedure.
First time you press 5 or ∞ button, the
chapter/track skips to the nearest higher
or lower chapter/track with a number of
multiple ten (ex. 10th, 20th, 30th).
Then each time you press the button, you
can skip 10 chapters/tracks.
Changing the display information
• After the last chapter/track, the first
chapter/track will be selected and vice
versa.
• For MP3/WMA, CD Text,
and audio CD, see page
41.
While playing a DVD
3
Each time you press the button
consecutively, the next or previous chapters/
tracks is located and played back.
While playing a VCD
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the playback modes
You can use only one of the following playback modes at a time.
1
2 Select your desired playback mode.
Repeat play
Mode
Plays repeatedly
CHP RPT*1 : The current chapter.
• RPT lights up.
• For DVD: During play or pause.
• For VCD: While PBC (see page 20) is
not in use.
TIT RPT*1 : The current title.
•
and RPT light up.
TRK RPT*2 : The current track.
• RPT lights up.
FLDR RPT*3 : All tracks of the current folder.
•
and RPT light up.
RPT OFF
: For DVD: Cancels Repeat play.
For other discs: All tracks of the
disc.
Ex.: When “TRK RPT” is selected while
playing an MP3 disc
Random play
Mode
Plays at random
FLDR RND*3 : All tracks of the current folder,
then tracks of the next folder
and so on.
• For VCD: While PBC (see page 20) is
not in use.
• RND and
DISC RND : All tracks of the disc.
• RND and light up.
RND OFF : Cancels.
light up.
Ex.: When “DISC RND” is selected while
playing an MP3 disc
*1 Only while playing a DVD disc.
*2 Except for DVD discs.
*3 Only while playing an MP3 or a WMA disc.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Dual Zone operations
3 Operate the DVD/CD player using
the remote controller by referring to
the monitor screen.
Listening with headphones
By connecting headphones to the 2nd
AUDIO OUT plug on the rear, you can
listen to the playback sound through the
DVD/CD player while listening to another
source through the speakers.
To cancel Dual Zone operations, repeat step 1.
(“DUAL OFF” appears on the display.)
You can activate Dual Zone while listening to
any source.
• When Dual Zone is in use, you can only
operate the DVD/CD player using the remote
controller.
On the control panel:
You can also activate and deactivate Dual Zone.
1
On the remote controller:
1 Activate Dual Zone.
2
The source automatically changes to
“DISC” when Dual Zone is activated.
The source automatically changes to
“DISC.”
To select a different source to listen through
the speakers, press SOURCE on the control
panel.
• By using the buttons on the control panel,
you can operate the newly selected source
without affecting Dual Zone operations.
Cautions:
• DO NOT put on the headphones while
driving a car. It is dangerous to shut off the
outside sounds while driving.
• DO NOT put on the headphones before
adjusting the 2nd VOL level properly;
otherwise, it may damage your hearing.
2 Adjust the headphone volume
through the 2nd AUDIO OUT plug.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound adjustments
Selecting preset sound modes
You can select a preset sound mode suitable to
the music genre.
Indication pattern for each sound mode:
USER
ROCK
CLASSIC
POPS
JAZZ
HIP HOP
Ex.: When “ROCK” is selected
4 Adjust the level (–05 to +05).
Storing your own sound
adjustments
You can adjust the sound modes and store your
own adjustments in memory.
1
5 Repeat steps 3 and 4 to adjust the
other frequency bands.
6 Store the adjustments in the
respective mode.
2 Enter the sound adjustment mode.
3 Select a frequency to adjust.
• For the preset frequency level settings, see
page 48.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Indication
FAD*2
(fader)
To do:
Range
R06
(Rear only)
to
Adjusting the sound
You can adjust the sound characteristics to your
preference.
Adjust the front
and rear speaker
balance.
F06
(Front only)
1
BAL
Adjust the left
L06
(balance)
and right speaker (Left only)
balance.
to
R06
(Right only)
LOUD
Boost low and
LOUD ON
(loudness)
high frequencies
J
Ex.: When “FAD” is selected
to produce a well- LOUD OFF
balanced sound at
low volume level.
2
SUB. W*3
Adjust the
00 (min.)
(subwoofer) subwoofer output to
level.
08 (max.)
VOL. A*4
(volume
adjust)
Adjust and store
the volume level
of each source.
–05 (min.)
to
+05 (max.)
Indication pattern changes as
you adjust the level.
VOL*5
(volume)
Adjust the
volume.
00 (min.)
to
30 or 50
(max.)*6
*2 If you are using a two-speaker system, set
the fader level to “00.”
*3 This takes effect only when a subwoofer is
connected.
*4 You cannot make an adjustment if the source
is FM. “FIX” will appear.
*5 Normally the control dial works as the
volume control. So you do not have to select
“VOL” to adjust the volume level.
*6 Depending on the amplifier gain control
setting. (See page 36 for details.)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
General settings — PSM
3 Adjust the PSM item selected.
Basic procedure
You can change PSM (Preferred Setting Mode)
items listed in the table that follows.
1
4 Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
2 Select a PSM item.
5 Finish the procedure.
Ex.: When you select “DIMMER”
Indications
Selectable settings, [reference page]
DEMO
Display demonstration
DEMO ON : [Initial]; Display demonstration will be activated
automatically if no operation is done for about
20 seconds, [11].
DEMO OFF : Cancels.
CLOCK H
1 – 12, [11]
Hour adjustment
[Initial: 1 (1:00)]
CLOCK M
00 – 59, [11]
Minute adjustment
[Initial: 00 (1:00)]
LEVEL
Audio level meter
ON
OFF
: [Initial]; Activates the audio level indicator.
: Cancels; sound mode indicator is shown, [33].
DIMMER
AUTO
: [Initial]; Dims the display when you turn on the
Dimmer
headlights.
ON
OFF
: Activates dimmer.
: Cancels.
TEL
MUTING 1/MUTING 2: Select either one which mutes the
Telephone muting
sounds while using the cellular phone.
OFF
: [Initial]; Cancels.
To be continued...
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Indications
Selectable settings, [reference page]
SCROLL*1
Scroll
ONCE
AUTO
OFF
: [Initial]; Scrolls the disc information once.
Repeats scrolling (5-second intervals in between).
: Cancels.
:
• Even if “SCROLL” is set to “OFF,” you can scroll the display by
pressing D DISP for more than one second.
WOOFER
Subwoofer cutoff
frequency
LOW
MID
: Frequencies lower than 80 Hz are sent to the
subwoofer.
: [Initial]; Frequencies lower than 120 Hz are sent to
the subwoofer.
HIGH
: Frequencies lower than 160 Hz are sent to the
subwoofer.
HPF
High pass filter
HPF ON
: The cut-off frequency is chosen automatically
according to the WOOFER setting (LOW/MID/
HIGH) so that you can enjoy the low frequency
effect (LFE) purely from the subwoofer if it is
connected.
HPF OFF
TAG ON
TAG OFF
PAL
:
[Initial]; Cancels.
TAG DISP
Tag display
: [Initial]; Shows the ID3 tag while playing MP3/
WMA tracks, [41].
: Cancels.
NTSC/PAL*2
: [Initial]; Select this if your monitor is of the PAL
Video format
color system.
NTSC
: Select this if your monitor is of the NTSC color
system.
REAR SPK*3
Rear speaker output
ON
OFF
: [Initial]; Select this to turn on the rear speaker output.
: Cancels.
AMP GAIN
Amplifier gain control
You can change the maximum volume level of this unit.
LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power
of the speaker is less than 50 W to prevent them from
damaging the speaker.)
HIGH PWR : [Initial]; VOL 00 – VOL 50
*1 Some characters or symbols will not be shown (and will be blanked) on the display
(Ex. “ABCå!d#” ]“ABCA D ”).
*2 The newly selected video format takes effect only after you turn on the power again, reload the
disc, or change the source.
*3 Displayed only when Dual Zone is activated (see page 32).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Other main functions
3 Assign a title.
Assigning titles to the sources
1 Select a character.
You can assign titles to station frequencies and
CDs (both in this unit and in the CD changer).
Maximum number of
Sources
characters
FM/AM tuner
DISC/CD-CH
Up to 8 characters (up to
30 station frequencies)
Up to 32 characters (up
to 30 discs)
2 Move to the next (or previous)
character position.
• You cannot assign a title to a DVD, VCD,
CD Text, or an MP3/WMA disc.
1 Select the source.
• For FM/AM tuner: Tune into a station.
• For a CD in this unit: Insert a CD.
• For CDs in the CD changer: Select
“CD-CH,” then select a disc number.
3 Repeat steps 1 and 2 until you
finish entering the title.
4 Finish the procedure.
2 Enter the title assignment mode.
To erase the entire title
In step 2 on the left column....
Ex.: When you select “DISC” as the source
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the control panel
Detaching the control panel
When detaching or attaching the control panel,
be careful not to damage the connectors on
the back of the control panel and on the panel
holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CD changer operations
Playing discs in the CD changer
Before connecting the CD changer
About the CD changer
• To prevent short circuits, it is
It is recommended to use the JVC MP3-
compatible CD changer with your unit.
• You can also connect other CH-X series
CD changers (except CH-X99 and
CH-X100). However, they are not
compatible with MP3 discs, so you cannot
play back MP3 discs.
recommended to disconnect the car
battery’s negative terminal and make all
electrical connections before connecting
the CD changer.
• When mounting this unit into your car, be
sure to use the screws provided.
• When tightening screws or bolts, be
careful not to pinch any connection cord.
• If you are not sure how to connect the
CD changer correctly, consult your car
dealer or JVC car audio dealer, or have it
installed by a qualified technician.
• You cannot play any DVD, VCD, and
WMA disc in the CD changer.
• You cannot use the KD-MK series CD
changers with this unit.
• Disc text information recorded in the CD
Text can be displayed when a JVC CD
Text compatible CD changer is connected.
Connecting the CD changer
All tracks of the inserted disc in the magazine
will be played repeatedly until you change
the source or eject the magazine from the CD
changer.
Connection cord supplied for the CD changer
~
JVC CD changer
Selected disc number
To be continued...
39
Download from Www.Somanuals.com. All Manuals Search And Download.
• When the current disc is an audio CD or a
CD Text disc:
Ÿ
Select a disc.
For disc number from 01 – 06:
CD Text: Disc title/performer =
Track title appear automatically
(see page 41).
For disc number from 07 – 12:
Elapsed playing
time
Current track
number
• When the current disc is an MP3 disc:
Current disc number
Current disc number
To fast-forward or reverse the track
Fast-forwards.
Reverses.
Folder name*
To go to the next or previous tracks
Current folder number
Disc information appears
automatically (see page 41).
To the following tracks.
Current track
number
Elapsed playing
time
To the beginning of the current track, then the
previous tracks.
To go to the next or previous folders (only
for MP3 discs)
* “ROOT” appears if no folder is included in
the disc.
To next folders.
To previous folders.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
To skip to a track quickly during play
• For MP3 disc, you can skip a track within the
same folder.
Ex.: To select track 32 while playing track 6
While playing an MP3 disc
• When “TAG DISP” is set to “TAG
ON” (see page 36)
1
2
First time you press 5 or ∞ button, the
track skips to the nearest higher or lower
track with a track number of multiple ten
(ex. 10th, 20th, 30th).
Then each time you press the button, you
can skip 10 tracks.
• After the last track, the first track will be
selected and vice versa.
• When “TAG DISP” is set to “TAG
OFF”
3
Changing the display information
*1 If no title is assigned to an audio CD, “NO
NAME” appears. To assign a title to an
audio CD, see page 37.
*2 If an MP3 file does not have ID3 tags, folder
name and file name appear. In this case, the
TAG indicator will not light up.
While playing an audio CD or a CD
Text
To be continued....
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the playback modes
You can use only one of the following playback modes at a time.
1
2 Select your desired playback mode.
Repeat play
Mode
Plays repeatedly
TRK RPT
: The current track.
• RPT lights up.
FLDR RPT* : All tracks of the current folder.
and RPT light up.
DISC RPT : All tracks of the inserted discs.
and RPT light up.
•
•
RPT OFF
: Cancels.
Ex.: When “TRK RPT” is selected while
playing an MP3 disc
Random play
Mode
Plays at random
FLDR RND* : All tracks of the current folder,
then tracks of the next folder
and so on.
• RND and
DISC RND : All tracks of the current disc.
• RND and light up.
light up.
MAG RND : All tracks of the inserted discs.
• RND lights up.
RND OFF : Cancels.
Ex.: When “DISC RND” is selected while
playing an MP3 disc
* Only while playing an MP3 disc.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
External component operations
Playing an external component
You can connect an external component to the
LINE IN plug on the rear, and another to the
AUX (auxiliary) input jack on the control panel.
Ÿ
!
Turn on the connected component
and start playing the source.
Adjust the volume.
Connecting the external component to the
LINE IN plug on the rear
Signal cord (not supplied)
External
component
⁄
Adjust the sound as you want.
(See pages 33 and 34.)
~
LINE IN: For selecting the external
component connected to the
LINE IN plug.
AUX IN: For selecting the external
component connected to the
AUX input jack.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
How to clean the connectors
To keep discs clean
Frequent detachment will deteriorate the
connectors.
A dirty disc may not play correctly.
If a disc does become dirty, wipe
it with a soft cloth in a straight line
from center to edge.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
• Do not use any solvent (for
example, conventional record cleaner, spray,
thinner, benzine, etc.) to clean discs.
To play new discs
New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
unit may reject the disc.
Connector
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.
Moisture condensation
Moisture may condense on the lens inside the
DVD/CD player in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the DVD/CD player may
malfunction. In this case, eject the disc and
leave the unit turned on for a few hours until the
moisture evaporates.
Do not use the following discs:
Warped
disc
Sticker
Sticker
residue
How to handle discs
When removing a disc from
Center holder
its case, press down the center
holder of the case and lift the
disc out, holding it by the
Stick-on
label
Disc
edges.
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs into the cases after
use.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Language codes
Code
Language
Code
Language
Code
Language
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
FI
Afar
IK
IN
IS
IW
JI
Inupiak
RN
RO
RW
SA
SD
SG
SH
SI
Kirundi
Rumanian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Indonesian
Icelandic
Hebrew
Yiddish
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
SK
SL
Slovenian
Samoan
Shona
SM
SN
SO
SQ
SR
SS
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Kirghiz
Latin
Lingala
ST
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
SU
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Twi
Ukrainian
Urdu
(Afan) Oromo
Oriya
Panjabi
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Polish
PS
PT
QU
RM
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
IE
45
Download from Www.Somanuals.com. All Manuals Search And Download.
More about this unit
• When a disc has been loaded, selecting
“DISC” for the playback source starts disc
play.
Basic operations
Turning on the power
• By pressing SOURCE on the unit, you can
also turn on the power.
Inserting a disc
• When a disc is inserted upside down,
“PLEASE” and “EJECT” appear alternately
on the display. Press 0 to eject the disc.
Selecting the sources
• When no disc is loaded in the unit, “DISC”
cannot be selected.
• Without connecting to the CD changer,
“CD-CH” cannot be selected.
Playing a DVD-R/DVD-RW or CD-R/
CD-RW
• Use only “finalized” discs.
Turning off the power
• If you turn off the power while listening to a
disc, disc play will start automatically, next
time you turn on the power.
• This unit can play back only the files of the
same type which is first detected if a disc
includes both audio CD (CD-DA) files and
MP3/WMA files.
• Only for CD-R/CD-RW: This unit can play
back multi-session discs; however, unclosed
sessions will be skipped while playing.
• Some DVD-R/DVD-RW or CD-R/CD-RW
may not play back on this unit because of
their disc characteristics, and for the following
causes:
– Discs are dirty or scratched.
– Moisture condensation occurs on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– CD-R/CD-RW on which the files are
written with “Packet Write” method.
– DVD-R/DVD-RW which are not written
in UDF-Bridge Format (eg. UDF format or
ISO format).
– There are improper recording conditions
(missing data, etc.) or media conditions
(stain, scratch, warp, etc.).
• DVD-RW/CD-RW may require a longer
readout time since the reflectance of
DVD-RW/CD-RW is lower than that of
regular discs.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and
stations are stored newly.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in
No. 1 will be automatically tuned in.
• When storing a station manually, a previously
preset station is erased when a new station is
stored in the same preset number.
Disc operations
General
• In this manual, words “track” and “file” are
interchangeably used when referring to MP3/
WMA files and their file names.
• This unit can also playback 8 cm discs.
• This unit can only playback audio CD
(CD-DA) files if different type of files are
recorded in the same disc.
– The first track will be skipped if a different
type of file is detected first.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use the following DVD-R/DVD-RW
or CD-R/CD-RW:
• This unit can play back the files recorded in
VBR (variable bit rate).
– Discs with stickers, labels, or protective seal
stuck to the surface.
– Discs on which labels can be directly
printed by an ink jet printer.
Using these discs under high temperatures or
high humidities may cause malfunctions or
damages to discs.
The files recorded in VBR have a discrepancy
in elapsed time display, and do not show
the actual elapsed time. Especially, after
performing the search function, this difference
becomes noticeable.
• This unit cannot play back the following files:
–
MP3 files encoded with MP3i and MP3 PRO
format.
Playing an MP3/WMA disc
– MP3 files encoded in an unappropriated
format.
• This unit can play back MP3/WMA files
with the extension code <.mp3> or <.wma>
(regardless of the letter case—upper/lower)
recorded in either CD-R/CD-RW or in
DVD-R/DVD-RW.
• This unit can show the names of albums,
artists (performer), and ID3 Tag (Version 1.0,
1.1, 2.2, 2.3, or 2.4) for MP3 files and WMA
files.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless,
professional, and voice format.
– WMA files which are not based upon
Windows Media® Audio.
– WMA files copy-protected with DRM.
– WMA files recorded with MBR (Multiple
Bit Rate) format.
• This unit can display only one-byte
characters. No other characters can be
correctly displayed.
• This unit can play back MP3/WMA files
meeting the conditions below:
– Files which have the data such as WAVE,
ATRAC3, etc.
Changing the source
• If you change the source, playback also stops
– Bit rate: MP3: 32 kbps — 320 kbps
WMA: 32 kbps — 192 kbps
– Sampling frequency:
(without ejecting the disc).
Next time you select “DISC” for the playback
source (without activating Dual Zone), disc
play starts from where it has been stopped
previously.
For MP3/WMA discs, playback will start
from the beginning of the last playing track.
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
48 kHz, 44.1 kHz, 32 kHz (for WMA)
– Disc format: ISO 9660 Level 1/ Level 2,
Romeo, Joliet, Windows long file name
• The maximum number of characters for file/
folder names vary among the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo: up to 128 characters
– Joliet: up to 64 characters
– Windows long file name: up to 128
characters
Ejecting a disc
• If the ejected disc is not removed within
15 seconds, the disc is automatically inserted
again into the loading slot to protect it from
dust. (Disc will not play this time.)
DVD setup menu
• When the language you have selected is not
recorded on a disc, the original language is
automatically used as the initial language. In
addition, for some discs, the initial languages
settings will not work as you set due to their
internal disc programming.
• This unit can recognize the total of
1100 files, 250 folders (maximum of 999 files
per folder).
To be continued....
47
Download from Www.Somanuals.com. All Manuals Search And Download.
• While playing (or pausing), you cannot
change these languages.
On-screen guide icons
After you change any of these language
settings, eject the disc and insert it (or another
disc) again so that your setting takes effect.
• When you select “16:9 [MULTI]” for a
picture whose aspect ratio is 4:3, the picture
slightly changes due to the process for
converting the picture width.
• Even if “4:3 [MULTI] PAN SCAN” is
selected, the screen size may become
“4:3 [MULTI] LETTER BOX” with some
DVDs. This depends on how they are
recorded.
During play, the following guide icons may
appear for a while on the monitor.
:
Appears at the beginning of a scene
containing multi-subtitle languages
(for DVD only).
: Appears at the beginning of a scene
containing multi-audio languages (for
DVD only).
: Appears at the beginning of a scene
containing multi-angle views (for
DVD only).
: Playback
: Pause
General settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the
volume level is set higher than “VOL 30,” the
unit automatically changes the volume level
: Forward Slow Motion Playback
(for DVD and VCD only)
: Reverse Slow Motion Playback
(for DVD only)
to “VOL 30.”
: Forward search
: Reverse search
Other main functions
• If you try to assign a title to a 31st station
or 31st disc, “NAMEFULL” flashes on
the display. Delete unwanted titles before
assignment.
• Titles assigned to discs in the CD changer can
also be shown if you playback the disc on the
unit.
Sound modes (preset frequency level settings)
The list below shows the preset frequency level settings for each sound mode (see page 33).
Preset equalizing values
Sound mode
60 Hz
00
150 Hz
00
400 Hz
00
1 kHz
00
2.4 kHz
00
6 kHz
00
15 kHz
00
USER
ROCK
CLASSIC
POPS
+03
+01
00
+02
+03
+02
+01
+02
00
00
+01
00
+02
+02
+01
+01
+03
+01
00
+01
00
00
00
00
+02
00
HIP HOP
JAZZ
+04
+03
–01
+01
–02
+01
00
+01
+01
48
Download from Www.Somanuals.com. All Manuals Search And Download.
About sounds reproduced through the rear terminals
• Through the analog terminals (Speaker out/LINE OUT/2nd AUDIO OUT): 2-channel signal is
emitted.
When playing a multi-channel encoded disc, multi-channel signals are downmixed.
(AUDIO—DOWN MIX: see page 28.)
• Through DIGITAL OUT (optical):
Digital signals (Linear PCM, Dolby Digital, DTS, MPEG Audio) are emitted through this
terminal. (For more details, see below.)
To reproduce multi-channel sounds such as Dolby Digital and DTS, connect an amplifier or
a decoder compatible with these multi-channel sources to this terminal, and set “DIGITAL
AUDIO OUTPUT” correctly. (See page 28.)
• About Dual Zone
While you are listening to the radio, CD changer, or external component through the speakers
built into your car compartment, you can listen to the playback sound of this DVD/CD player
using the headphones connected to the 2nd AUDIO OUT plug at the same time. (For details,
see page 32.)
Output signals through the DIGITAL OUT terminal
Output signals are different depending on the “DIGITAL AUDIO OUTPUT” setting on the setup
menu (see page 28).
DIGITAL AUDIO OUTPUT
Output Signals
Playback Disc
STREAM/PCM
DOLBY DIGITAL/PCM
PCM ONLY
DVD
48 kHz, 16/20/24 bits Linear PCM
96 kHz, Linear PCM
with DTS
48 kHz, 16 bits stereo Linear PCM
DTS bitstream
Dolby Digital bitstream
MPEG bitstream
48 kHz, 16 bits stereo Linear PCM
48 kHz, 16 bits
stereo Linear PCM
with Dolby Digital
with MPEG Audio
48 kHz, 16 bits Linear PCM
Audio CD, Video CD
44.1 kHz, 16 bits stereo Linear PCM /
48 kHz, 16 bits stereo Linear PCM
Audio CD with DTS
DTS bitstream
44.1 kHz, 16 bits stereo Linear PCM
MP3/WMA
32/44.1/48 kHz, 16 bits Linear PCM
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
Causes
Remedies
• Sound cannot be heard
from the speakers.
The volume level is set to
the minimum level.
Adjust it to the optimum
level.
Connections are incorrect.
Check the cords and
connections.
• The unit does not work at
all.
The built-in microcomputer Reset the unit (see page 2).
may have functioned
incorrectly due to noise, etc.
• Remote controller does not Dual Zone is activated
work. (see page 32).
While Dual Zone is
activated, remote controller
only functions for operating
the DVD/CD player.
• SSM automatic presetting Signals are too weak.
Store stations manually.
does not work.
• Static noise while listening The antenna is not connected Connect the antenna firmly.
to the radio.
firmly.
• Disc cannot be played
back.
Disc is inserted upside
down.
Insert the disc correctly.
• CD-R/CD-RW or DVD-R/ CD-R/CD-RW or DVD-R/
DVD-RW cannot be played DVD-RW is not finalized.
back.
• Insert a finalized CD-R/
CD-RW or DVD-R/
DVD-RW.
• Tracks on the CD-R/
CD-RW or DVD-R/
DVD-RW cannot be
skipped.
•
Finalize the CD-R/CD-RW
or DVD-R/DVD-RW with
the component which you
used for recording.
• Disc cannot be recognized. The DVD/CD player may
Eject the disc forcibly
have functioned incorrectly. (see page 2).
• “NO DISC” appears on the Disc is inserted incorrectly.
Insert the disc correctly.
display.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptoms
Causes
Remedies
• Sound and picture are
sometimes interrupted or
distorted.
You are driving on rough
roads.
Stop playback while driving
on rough roads.
Disc is scratched.
Change the disc.
Connections are incorrect.
Check the cords and
connections.
• No playback picture
(DVD, VCD) appears on
the monitor.
Parking brake wire is not
connected properly.
See Installation/Connection
Manual.
• No picture appears on the
monitor at all.
The video cord is not
connected correctly.
Connect the video cord
correctly.
An incorrect input has
been selected on the TV or
monitor.
Select a correct input on the
TV or monitor.
• The playback picture
(DVD, VCD) are not
stable and distorted.
The disc (DVD, VCD) is
recorded in NTSC format.
Change the disc.
Change the video format to
NTSC (see page 36).
• The left and right edges of “4:3 [MULTI] PAN SCAN” Select “4:3 [MULTI]
the picture are missing on is selected when viewing on LETTER BOX.”
the screen.
a conventional TV
(aspect ratio 4:3).
(See page 27.)
• Disc cannot be played
back.
No MP3/WMA tracks are
recorded on the disc.
Change the disc.
MP3/WMA tracks do not
have the extension code
<.mp3> or <.wma> in their
file names.
Add the extension code
<.mp3> or <.wma> to their
file names.
MP3/WMA tracks are not
recorded in a compliant
format.
Change the disc.
Record MP3/WMA tracks
using a compliant application
(see page 6).
MP3/WMA tracks are
recorded in DVD+R/
DVD+RW media.
Change the disc.
Record MP3/WMA tracks
using DVD-R/DVD-RW
media.
To be continued....
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptoms
Causes
Remedies
• Noise is generated.
The track played back is not Skip to another track or
an MP3/WMA file (although change the disc. (Do not add
it has the extension code
<.mp3> or <.wma>).
the extension code <.mp3>
or <.wma> to non-MP3 or
WMA tracks.)
• A longer readout time is
Readout time varies due to
Do not use too many
required.
the complexity of the folder/ hierarchies and folders.
file configuration.
• Tracks cannot be played
Playback order is determined
back as you have intended when the files are recorded.
them to play.
• Elapsed playing time is not This sometimes occurs
correct.
during play. This is caused
by how the tracks are
recorded on the disc.
• “PLEASE” and “EJECT”
appear alternately on the
display.
The current disc does not
contain any MP3/WMA
tracks.
Insert a disc that contains
MP3/WMA tracks.
•
Correct characters are not
This unit can only display
displayed (e.g. album name). alphabets (capital: A – Z),
numbers, and a limited
number of symbols.
• “NO DISC” appears on the No disc is in the magazine.
Insert disc into the magazine.
display.
Disc is inserted upside down. Insert disc correctly.
No magazine is loaded in the Insert the magazine.
• “NO MAG” appears on
the display.
CD changer.
• “RESET 8” appears on the This unit is not connected to Connect this unit and the CD
display.
the CD changer correctly.
changer correctly and press
the reset button of the CD
changer.
• “RESET 1” – “RESET 7”
appears on the display.
Press the reset button of the
CD changer.
• The CD changer does not
work at all.
The built-in microcomputer Reset the unit (see page 2).
may function incorrectly due
to noise, etc.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front: 50 W per channel
Rear: 50 W per channel
DVD/CD PLAYER SECTION
Continuous Power Output (RMS):
Front: 19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of Channels: 2 channels (stereo)
Frequency Response:
Rear: 19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
DVD, fs=48 kHz/96 kHz:16 Hz to 22 000 Hz
VCD, CD, MP3, WMA: 16 Hz to 20 000 Hz
Dynamic Range:
96 dB
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range:
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
MP3 (MPEG Audio Layer 3):
Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio):
Max. Bit Rate: 192 kbps
Frequencies: 60 Hz, 150 Hz, 400 Hz, 1 kHz,
2.4 kHz, 6 kHz, 15 kHz
Level: 10 dB
Signal-to-Noise Ratio: 70 dB
Audio Output Level:
Analog (2nd AUDIO OUT):
6 mW (at 16 Ω)
GENERAL
Digital (DIGITAL OUT: Optical):
Signal wave length: 660 nm
Output level: –21 dBm to –15 dBm
Line-Out Level/Impedance:
5.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 158 mm
Panel Size (approx.):
Subwoofer-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Color System: PAL/NTSC
Video Output (composite): 1 Vp-p/75 Ω
Other Terminals: LINE IN, CD changer
188 mm × 58 mm × 11 mm
Mass (approx.): 1.7 kg (excluding accessories)
TUNER SECTION
Frequency Range:
Design and specifications are subject to change
without notice.
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
EN, CT
© 2005 Victor Company of Japan, Limited
0905DTSMDTJEIN
Download from Www.Somanuals.com. All Manuals Search And Download.
|