COMPACT VHS CAMCORDER
GR-AX910
GR-AX810
Compact VHS
For Customer Use:
Enter below the Serial Nos. of the
GR-AX910U/GR-AX810U camcorder
and the AA-V11U AC Power Adapter/
Charger.
The serial numbers are located on the
bottom of the GR-AX910U/GR-AX810U,
and the AA-V11U.
INSTRUCTIONS
Model No. GR-AX910U/GR-AX810U
AA-V11U
Serial No.
YU30052-537
Download from Www.Somanuals.com. All Manuals Search And Download.
3
5. Ventilation
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the product and
to protect it from overheating, these openings must not be
blocked or covered.
Electrical energy can perform many useful functions. But
improper use can result in potential electrical shock or fire
hazards. This product has been engineered and
• Do not block the openings by placing the product on a
bed, sofa, rug or other similar surface.
• Do not place the product in a built-in installation such as
a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
manufactured to assure your personal safety. In order not to
defeat the built-in safeguards, observe the following basic
rules for its installation, use and servicing.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
ATTENTION:
Follow and obey all warnings and instructions marked on
your product and its operating instructions. For your safety,
please read all the safety and operating instructions before
you operate this product and keep this manual for future
reference.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized
alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature.
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
2. Lightning
(B) Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third (grounding)
pin. This plug will only fit into a grounding-type power
outlet. This is a safety feature.
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type
plug.
3. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
2. Power Sources
Operate your product only from the type of power source
indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your product
dealer or local power company. If your product is intended
to operate from battery power, or other sources, refer to the
operating instructions.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
ANTENNA
LEAD IN WIRE
4. Power Cord Protection
GROUND CLAMP
Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
Download from Www.Somanuals.com. All Manuals Search And Download.
4
USE
SERVICING
1. Servicing
1. Accessories
To avoid personal injury:
If your product is not operating correctly or exhibits a
marked change in performance and you are unable to
restore normal operation by following the detailed
procedure in its operating instructions, do not attempt to
service it yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
• Do not place this product on an unstable cart, stand,
tripod, bracket or table. It may fall, causing serious injury
to a child or adult, and serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the
product.
• Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s instructions
for any mounting of the product.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
• Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
2. Product and Cart Combination
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Water and Moisture
PORTABLE CART WARNING
(Symbol provided by RETAC)
Do not use this product near
water—for example, near a bath
tub, wash bowl, kitchen sink or
laundry tub, in a wet basement, or
near a swimming pool and the
like.
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
4. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
4. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in safe operating condition.
5. Attachments
Do not use attachments not recommended by the
manufacturer of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
7. Heat
The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK OPERATION GUIDE
5
SUPPLY POWER
INSERTING A VIDEO
CASSETTE
Hook on.
1
EJECT
1
Push in.
2
3
PUSH
2
Insert.
BATT. RELEASE
Using the battery pack
1 Hook-on the battery pack's top end to the
camcorder. (Charging procedure, ੬ P. 8)
2 Push in the battery pack until it locks into
place.
1 Slide EJECT.
2 Insert a video cassette.
3 Press PUSH.
(For more details, ੬ P. 13)
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
PLAYBACK
SHOOTING
PLAY/PAUSE
3
REW
2
1
LENS COVER
open/close knob
2
Set to “CAMERA”
STOP
Recording Start/Stop button
3
1
Set to “PLAY”
1 Set the power switch to “PLAY”.
2 Press REW.
1 Slide the LENS COVER open/close knob to
open the lens cover.
2 Set the power switch to “CAMERA”.
— The power indicator will light and an
image will appear in the viewfinder.
3 Press RECORDING START/STOP.
— Recording starts.
— The tape will automatically stop at the
beginning of the tape.
3 Press PLAY/PAUSE.
— Playback starts and the playback picture
appears in the viewfinder.
•To stop playback, press STOP.
(For more details, ੬ P. 38.)
•To stop recording temporarily, momentarily
press the Recording Start/Stop button once
again.
(For more details, ੬ P. 16)
Ⅲ Or simply play back the tape on a VHS
VCR using the Cassette Adapter
(VHS Playpak). ੬ P. 36
Download from Www.Somanuals.com. All Manuals Search And Download.
MAJOR FEATURES
6
REMEMBER
Multi Function Control
(੬ pg. 22 – 35)
The Logical Choice
Digital Hyper Zoom (੬ pg. 17)
Zoom-in
The only compact video
cassettes that can be
used with your VHS VCR*
*with VHS Playpak
W
W
W
W
T
T
T
T
Zoom-out
Program AE with Special
Effects (੬ pg. 26)
Digital Image Stabilizer
(੬ pg. 22)
Ⅲ Cinema Ⅲ Sepia Ⅲ Twilight Ⅲ Sports
Ⅲ High Speed (1/2000 sec.) Shutter
Digital Wipes and Fades
(੬ pg. 28)
● Black Fader
● Mosaic Fader
● Slide Wipe
Random Assemble Editing
● Blue Fader
● Shutter Wipe
(੬ pg. 40 – 43)
2
8
5
4
1
6
3
7
1
2
3
4
5
6
7
8
Built-In Auto Light (੬ pg.19)
PROVIDED ACCESSORIES
•AC Power Adapter/
Charger AA-V11U
•Remote Control
Unit RM-V705U
•Cassette Adapter
(VHS PlayPak)
C-P7U
•Battery Pack
BN-V11U
•DC Cord
•Lithium Battery
•Shoulder Strap
CR2025
Cassettes marked
can be used with this camcorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
7
GETTING STARTED
8
Power ................................................................................................ 8
Clock (Lithium) Battery Removal/Insertion................................................... 10
Viewfinder Adjustment ..........................................................................10
Date/Time Setting ...............................................................................11
Tape Length Setting ..............................................................................12
Recording Mode Setting .........................................................................13
Loading/Unloading A Cassette .................................................................13
Grip Adjustment ..................................................................................14
Shoulder Strap Attachment ......................................................................14
Tripod Mounting ..................................................................................14
Using The RM-V705U Remote Control Unit ..................................................15
RECORDING
16
Basic Recording ...................................................................................16
Basic Features.....................................................................................17
Video Light ........................................................................................19
Advanced Features ...............................................................................20
Date/Time Insert ................................................................................... 20
Quick Rec. ........................................................................................... 21
Digital Image Stabilizer (D.I.S.) .............................................................. 22
Exposure Control .................................................................................. 22
White Balance Adjustment..................................................................... 23
Focusing............................................................................................... 24
Program AE With Special Effects............................................................. 26
Fade/Wipe ............................................................................................ 28
Using Menu For Detailed Adjustment ..................................................... 30
Instant Titles ......................................................................................... 32
Self-Timer ............................................................................................. 34
Animation ............................................................................................ 35
Time Lapse ........................................................................................... 35
PLAYBACK
36
Using The Cassette Adapter.....................................................................36
Basic Connections ................................................................................. 37
Basic Playback ....................................................................................38
Features ........................................................................................... 39
EDITING
40
Tape Dubbing ...................................................................................... 40
Random Assemble Editing [R.A.Edit]...........................................................40
Insert Editing ...................................................................................... 44
Audio Dubbing.....................................................................................45
USER MAINTENANCE
TROUBLESHOOTING
INDEX
46
47
49
Controls ............................................................................................49
Connectors .........................................................................................50
Indicators ..........................................................................................50
Other Parts ........................................................................................50
Viewfinder ........................................................................................51
Terms ...............................................................................................52
CAUTIONS
SPECIFICATIONS
ESPAÑOL
FOR SERVICING
WARRANTY
53
55
56
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
8
Power
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.
CHG. (charge) indicator
Marks
NOTES:
● No function is available without power supply.
● Use only specified power supply.
● Do not use provided power supply units with other equipment.
POWER
indicator
To AC outlet
CHARGING THE BATTERY PACK
END
indicator
SUPPLY POWER
Connect the charger’s AC power cord to a wall
1
2
outlet. The power indicator lights.
ATTACH BATTERY PACK
Align the marks and slide the battery pack in the
direction of the arrow until it locks in place.
The CHG. indicator lights.
REFRESH switch
REFRESH indicator
DETACH BATTERY PACK
When charging is completed, the END indicator
lights. Slide the battery pack opposite the direction
of the arrow.
3
BATT. PACK
CHARGE
DISCHARGE
BN-V11U
BN-V12U
BN-V22U
BN-V25U
approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
approx. 2 hrs. 10 min. approx. 7 hrs.
Hook on.
approx. 2 hrs. 40 min. approx. 10 hrs.
USING THE BATTERY PACK
ATTACH BATTERY PACK
Hook its top end to the camcorder and push the
Push in.
BATT. RELEASE
1
2
battery pack in until it locks in place.
DETACH BATTERY PACK
Slide BATT. RELEASE and pull out the battery pack.
ATTENTION:
Before detaching the power source,
make sure that the camcorder’s power
is turned off. Failure to do so can result
in a camcorder malfunction.
APPROXIMATE RECORDING TIME
BATT. PACK
BN-V11U
BN-V12U
BN-V22U
GR-AX910
1 hr. (35 min.)
1 hr. (35 min.)
GR-AX810
1 hr. 5min. (35 min.)
1 hr. 5min. (35 min.)
2 hrs. 10 min.
(1 hr. 20 min.)
2 hrs. 15 min.
(1 hr. 25 min.)
**REFRESH
The AC power adapter features a REFRESH function
that allows you to fully discharge the battery pack
before recharging.
BN-V25U
2 hrs. 50 min.
(1 hr. 50 min.)
3 hrs.
(1 hr. 50 min.)
(
): When the Video Light is on
To discharge the battery . . .
..... attach the battery pack to the adapter as shown
in the illustration to the left. Then push
REFRESH. The REFRESH indicator lights when
discharging starts, and goes out when
discharging is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
**CHARGE MARKER
A charge marker is provided on the battery pack to
help you remember whether it has been charged or
not. Two colors are provided (red and black)—you
choose which one means charged and which
means discharged.
Charge marker
NOTES:
● The recording time per charge is affected by such factors as the time spent in Record/Standby mode and
the frequency of zooming. It is safer to have spare battery packs.
● Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully
charged battery pack.
● Charging and discharging times vary according to the ambient temperature and the status of the battery
pack.
● Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.
● Perform the REFRESH function after no less than 5 chargings.
● High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.
● If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.
● Remove the battery pack from the adapter immediately after discharging.
● To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
● Make sure you unplug the DC cord before charging or discharging the battery pack.
● A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to
continue.
● The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should light during recharging. If not, contact your nearest JVC dealer.
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).
To
DC OUT
terminal
To AC outlet
To
DC IN
Jack
NOTES:
● When using the car battery, leave the engine
idling.
AC Power
Adapter/Charger
● The optional Car Battery Charger (BH-V3U) can
also be used to charge the battery pack.
● When using the optional Car Battery Charger or
Car Battery Cord (AP-V7U), refer to the respective
instruction booklet.
AA-V11U (provided)
DC cord
To car's
cigarette
lighter
USING AC POWER
Use the AC Power Adapter (connect as shown in
the illustration to the left).
Car Battery Cord
AP-V7U (optional)
socket
NOTE:
The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
Car Battery Charger/Adapter
BH-V3U (optional)
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED (cont.)
10
Clock (Lithium) Battery Insertion/Removal
A
This battery is necessary for clock operation and to
perform date/time settings.
SWITCH OFF POWER
Switch off the unit’s power and remove the power
1
2
supply unit.
OPEN COVER
Open the clock battery compartment cover while
pressing the release tab.
REMOVE BATTERY (when replacing)
Insert a pointed, non-metallic object between the
3 battery and the compartment (
A
) and pull the
battery out.
INSERT BATTERY
Ensuring the plus (+) side is up, insert a CR2025
lithium battery and push it in.
4
5
CLOSE COVER
Close the compartment cover until it clicks in place.
NOTE:
See “SAFETY PRECAUTIONS”(੬ pg. 2) for information
on safe handling of lithium batteries.
Viewfinder Adjustment
3
POSITION VIEWFINDER
Adjust the viewfinder manually for best viewability
1
2
3
(see illustration at left).
SELECT MODE
1
Set the power switch to CAMERA.
2
ADJUST DIOPTER
Turn the diopter adjustment control until the
indications in the viewfinder are clearly focused.
Set POWER to “CAMERA”.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Date/Time Setting
Shooting mode selector
FAR
SELECT MODE
Set the Power switch to “CAMERA”, and the
MENU
+
1
2
3
Shooting Mode selector to “PRESET”.
ACCESS MAIN MENU SCREEN
Press MENU.
SELECT FUNCTION
NEAR
Press – to move the highlight bar down to “Date/
Time”, then press NEAR. The Set Date And Time
screen appears.
–
SET DATE/TIME
Press FAR or NEAR until the item you want to set
begins blinking, then press + or – to until the correct
setting appears.
4
•If you decide you want to return the date and time
to the previous settings, press FAR or NEAR to
move the highlight bar to “Cancel”, then press
MENU.
•If you’re satisfied with the settings, go on to step 5.
START CLOCK OPERATION
Once you’ve set the month, day, year and time,
press FAR or NEAR until “Set” begins to blink, then
press MENU. The Main Menu screen reappears.
5
6
Main Menu
CLOSE MAIN MENU
Screen
Tele Macro
Gain Up
OFF
AGC
NOR.
T30
Press MENU.
Color Filter
Tape Length
Title
Date/Time
Sub Menu
NOTES:
● To display the date and time in the viewfinder and on a
connected TV, see “Date/Time Insert” (੬ pg. 20).
● If, in step 4, you input an invalid date (FEB 30, JUN 31,
etc.) and perform step 5, “Input Error” appears blinking
at the bottom of the screen. Press +, –, FAR or NEAR to
make the day blink, and input the correct number.
Set Time and
Date Screen
JAN 1.00 AM 12:00
Set
Cancel
Date
Month/Day/Year
Time
12-hour indication with
AM or PM
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED (cont.)
Tape Length Setting
12
FAR
+
SELECT MODE
Set the Power switch to “CAMERA”, and the
Shooting Mode selector to “PRESET”.
1
2
3
4
ACCESS MAIN MENU SCREEN
Press MENU.
NEAR
SELECT FUNCTION
Press + or – to move the highlight bar to “Tape
Length”.
–
SET TAPE LENGTH
Press FAR or NEAR to cycle through until the correct
setting appears (depending on the tape used). T20 =
20 minutes of recording time, T30 = 30 min., and
T40 = 40 min. (when recording in SP mode).
CLOSE MAIN MENU
Press MENU.
5
NOTE:
The tape remaining time (੬ pg. 16) displayed in the
viewfinder is correct only if the correct tape length has
been selected.
Main Menu
Screen
Tele Macro
Gain Up
OFF
AGC
NOR.
T40
Color Filter
Tape Length
Title
Date/Time
Sub Menu
T20
T30
T40
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Recording Mode Setting
SP/EP
Pressing SP/EP alternates the setting between SP
(standard play-provides higher picture and sound
quality, better for dubbing) and EP (Extended Play-
more economical, recording at 1/3 the speed of SP).
1
NOTE:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
Loading/Unloading A Cassette
OPEN CASSETTE HOLDER
Slide EJECT until the holder opens. Do not use force
1
2
3
to open.
INSERT/REMOVE CASSETTE
Make sure the label is facing outward.
CLOSE CASSETTE HOLDER
Press PUSH and make sure the holder is closed and
locked.
NOTES:
● A cassette holder can’t be opened unless a power
supply is attached.
● Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
● Make sure the Erase Protection tab is present. If not,
cover the hole with adhesive tape. (Some cassettes
have sliding tabs – in this case, check the tab's
position.)
Turn to take up
slack.
Erase Protection
Gear
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED (cont.)
Grip Adjustment
14
EXPAND LOOP
Separate the Velcro strip.
1
2
3
INSERT HAND
Pass your right hand through the loop and grasp the
grip.
ADJUST STRAP LENGTH
Adjust so your thumb and fingers can easily operate
the Recording Start/Stop button and Power Zoom
lever. Refasten the Velcro strip.
Recording Start/Stop button
Shoulder Strap Attachment
ATTACH STRAP
Following the illustration at left, thread the strap
1
through the top of the eyelet 1, then fold it back
and thread it through the keeper 2, and then
through the buckle 3. Repeat the procedure to
attach the other end of the strap to the other eyelet,
making sure the strap isn’t twisted.
1
3
2
2
1
ADJUST LENGTH
Adjust as shown in the illustration at left 1, then
slide both keepers snug against the eyelets to
prevent slipping 2.
2
Tripod Mounting
ALIGN AND TIGHTEN
Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Using The RM-V705U Remote Control
Unit
The Full-Function Remote Control Unit can operate this
camcorder from a distance as well as the basic
operations (PLAY, STOP, PAUSE, FF, and REW) of your
VCR. This remote control unit makes additional
recording functions possible.
Infrared beam
effective area
10°
Infrared beam
sensor window
PULL OUT BATTERY HOLDER
10°
Pull out the battery holder by inserting a pointed
The transmitted beam may not be effective or
may cause incorrect operation when the
infrared beam sensor window is directly
exposed to sunlight or powerful lighting.
1 instrument into slot
A
.
INSERT BATTERY
Insert the lithium battery *(CR2025), with its plus (+)
2
3
side up, into the battery holder.
1
REPLACE BATTERY HOLDER
Insert the battery holder into the remote control unit,
and push the holder until it clicks in place.
2
7
8
9
0
!
@
*Read warning on lithium battery. (੬ P. 2)
3
4
5
6
A
Functions
Buttons
With the camcorder’s power switch
set to “CAMERA”.
With the camcorder’s power switch set
to “PLAY”.
1 Infrared beam
transmitting window
Transmits the beam signal.
2 ZOOM (T/W) buttons
3 PLAY button
Zoom (invariable speed, ੬ pg. 17)
—
Playback start (੬ pg. 38)
Stop (੬ pg. 38)
—
—
4 STOP button
5 REW button
Retake (Rewind) (੬ pg. 18)/
Quick Review (੬ pg. 17)
Rew/Rew Shuttle Search (੬ pg. 38)
6 INSERT button
7 START/STOP button
8 INT. TIME button
9 REC TIME button
0 PAUSE button
! FF button
—
Insert Editing (੬ pg. 44)
Functions same as the Recording Start/Stop button of the camcorder.
Self-Timer(੬ pg. 34)/Time Lapse (੬ pg. 35)
Animation/Time lapse (੬ pg. 35)
—
—
—
Retake (Forward) (੬ pg. 18)
—
Pause/Play (during Pause mode) (੬pg. 38)
FF/FF Shuttle Search (੬ pg. 38)
Audio dubbing (੬ pg. 45)
@ A. DUB button
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Basic Recording
16
NOTE:
LENS COVER
SWITCH
You should already have performed the procedures listed
below. If not, do so before continuing.
● Power (੬ pg. 8)
● Tape Length (੬ pg. 12)
● Recording Mode Setting (੬ pg. 13)
● Grip Adjustment (੬ pg. 14)
LOAD A CASSETTE
Slide EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
1
2
POWER
Start/Stop
The power indicator
ENTER RECORD–STANDBY MODE
Slide the LENS COVER open/close switch to open
the lens cover, then set the power switch to
“CAMERA”.
•The power indicator lights and the camcorder
enters the Record–Standby Mode.
•The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
START SHOOTING
25min
Press the RECORDING START/STOP button.
Tally lamp
3
4
•The tally lamp lights while recording is in progress,
and “REC ” appears in the viewfinder.
•If you want to turn the tally lamp off, see page 31.
STOP RECORDING
Tape remaining time indicator
Press the RECORDING START/STOP button again to
stop recording.
120min
119min
3min
1min (Blinking)
0min (Blinking)
2min (Blinking)
•The camcorder re-enters the Record-Standby
mode.
*
min.....(Now calculating)
NOTES:
● A cassette holder can’t be opened unless a power supply is attached.
● There may be a delay after you slide EJECT until the holder opens. Do not use force.
● The tape’s remaining time is displayed in the viewfinder as shown.
● The indicated remaining time is approximate.
● The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
● The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been
selected (੬ pg. 12).
● “TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is
loaded.
● If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations,
the camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to
“CAMERA” to turn the camcorder on again.
● If you’re recording on a cassette from the middle, use the RETAKE function (੬ pg. 18) to find the end of
the last recording so you don’t erase any of it.
● The LENS COVER warning blinks for about 8 seconds when the camcorder is turned on, when the cover is
closed.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Basic Features
17
FEATURE:
PURPOSE:
Zooming
To produce the zoom in/out effect, or
an instantaneous change in image
magnification.
Zoom-in
W
W
W
W
T
T
T
T
OPERATION:
28X Hyper zoom
Digital circuitry doubles the
maximum 14x magnification offered
by optical zoom.
Zoom-out
1) To zoom in, slide the Zoom Lever
toward “T”.
Zoom indicator bar
2) To zoom out, slide toward “W”.
W
NOTES:
● During Hyper Zoom, the speed
increases the further you slide the
Zoom Lever.
Zoom level
indicator
● Focusing may be come unstable
during Hyper Zoom. In this case,
set the zoom while in Record –
Standby, set manual focus or Focus
Lock (੬ pg. 24, 25), then zoom in
or out in Record mode.
T
● The Zoom Level Indicator (5) only
moves during optical zoom. Once
the indicator reaches “T”, all
magnification from that point is
through digital processing.
● During digital image processing,
the quality of the image may suffer.
Power zoom lever
FEATURE:
PURPOSE:
Quick Review
To check the end of the last
recording.
OPERATION:
1) Press “ ” and release quickly
during the Record–Standby mode.
•Tape is rewound for about
2seconds and played back
automati-cally, then pauses in
Record–Standby mode for the
next shot.
NOTE:
Distortion may occur at start of
playback.
This is normal.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Basic Features (cont.)
18
FEATURE:
PURPOSE:
Index Code Marking
To give you automatic access to any
selected point on a recording. Auto
Marking and Manual Marking are
available.
OPERATION:
Auto Marking
An index code is marked to start the
first recording after a cassette is
inserted, as long as the Power switch
is set to “CAMERA”.
Manual Marking
1) Press VISS once to place the index
code. INDEX blinks in the
viewfinder during marking.
If VISS is pressed during
Record–Standby mode, the mark is
placed where RECORDING
START/STOP is pressed.
START/STOP
VISS
NOTE:
RM-V700U (optional)
FEATURE:
Retake
PURPOSE:
OPERATION:
To re-record certain segments.
1) Make sure the camcorder is in the
Record–Standby mode.
2) Press either RETAKE button to
reach the start point for new
recording.
RETAKE
3) Press RECORDING START/STOP
to start recording.
NOTE:
Noise may appear during Retake.
This is normal.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Video Light
When natural lighting is too dim, you can brighten the
scene by using the built-in video light.
SET VIDEO LIGHT
Set the LIGHT ON/AUTO/OFF as required.
1 ON
: Always keeps the light on as long as the
camcorder is turned on.
AUTO : Automatically turns on the light when the
camcorder senses insufficient lighting on
the subject.
LIGHT ON/AUTO/OFF
OFF : Turns off the light.
•The video light can be used with the camcorder’s
power on.
•It is recommended to set the white balance
(੬ pg. 23) to indoor mode ( ) when you use the
video light.
•When not using the video light, turn it off to save
battery power.
NOTES:
● Even if the battery indicator (
) does not blink in the
viewfinder, if the battery pack’s charge is low, the
camcorder may turn off automatically when you turn
on the video light, or when you start recording with the
video light turned on.
● When the LIGHT ON/AUTO/OFF switch is set to
“AUTO”:
•Depending on the lighting conditions, the video light
may keep turning on and off. In this case, manually
switch the light on or off using the LIGHT ON/
AUTO/OFF switch.
•While the Sports or High-Speed Shutter mode
(੬ pg. 27) is engaged, the light is likely to stay on.
•While the Twilight mode (੬ pg. 27) is engaged, the
light will not activate.
DANGER
•The video light become extremely hot. Do not
touch it either while in operation or soon after
turning it off, otherwise serious injury may result.
•Do not place the camcorder into the carrying case
immediately after using the video light, since it
remains extremely hot.
•When operating, keep a distance of about 30 cm.
(1 ft.) between the video light and people or
objects.
•Do not use near flammable or explosive materials.
•It is recommended that you consult your nearest
JVC dealer for replacing the video light.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features
20
Date/Time Insert
This feature allows you to display the date and time in your
viewfinder and on a connected TV.
NOTE:
You should already have performed the Date/Time
Setting procedure (੬ pg. 11). If you haven’t, do so
before continuing.
DISPLAY
DISPLAY
CHOOSE DISPLAY MODE
Press DISPLAY during Record–Standby to cycle
through the available modes as shown in the
illustration at left.
1
NOTES:
● The selected display can be recorded.
● If you don't want to record the display, select Date-off
mode before shooting.
DEC 25. 96
PM 3:29:43
Date display
Time display
● If you want to delete the display during shooting, press
DISPLAY.
● If you want to call back a deleted display, engage the
Record-Standby mode and then press DISPLAY to
select the desired display mode.
Date/Time-off mode
Date/Time display
Date display
DEC 25. 96
Time display
PM 10: 59:20
Date/Time display
DEC 25. 96
PM 10: 59:20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Quick Rec
QUICK REC
Records a scene for 5 seconds, providing quick scene
transitions like those seen in TV programmes.
During Record–Standby, press and release QUICK
1
REC. Recording starts, and after 5-second
recording is finished, the camcorder reenters the
Record–Standby mode automatically.
•To continue shooting longer than 5 seconds,
press and hold QUICK REC. Recording continues
as long as QUICK REC is kept pressed.
NOTES:
● The Fader (੬ pg. 24) cannot be activated by pressing
QUICK REC.
● QUICK REC cannot be used during Animation and
Time-Lapse (੬ pg. 35).
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
22
Digital Image Stabilizer
This feature compensates for unstable images caused by
camera-shake, particularly noticeable at high
magnification.
ACTIVATE D. I. STABILIZER
Press D.I.STABILIZER. “ ” appears in the viewfinder.
1
•To switch off the Digital Image Stabilizer, press
D.I.STABILIZER. The indicator disappears.
Shooting Mode Selector
NOTES:
+
D.I. STABILIZER
● Accurate stabilization may not be possible if hand
shake is excessive, or under the following conditions:
• When shooting subjects with vertical or horizontal
stripes
• When shooting dark or dim subjects
• When shooting subjects with excessive backlighting
• When shooting scenes with movement in various
directions
• When shooting scenes with low-contrast
backgrounds
–
● Switch off DIS when recording with the camcorder on
a tripod.
Exposure Control
This feature automatically adjusts the iris for the best
available picture quality, but you can override and make
the adjustment manually.
SELECT SHOOTING MODE
Set the Shooting Mode selector to “PRESET”.
1
Viewfinder
D.I.S. Indicator
BRIGHTEN IMAGE
Press + (maximum +06). The Exposure level
+
02
2
indicator appears in the viewfinder.
OR . . .
DARKEN IMAGE
Press – (maximum –06). The Exposure level
indicator appears in the viewfinder.
Exposure Level Indicator
When you want to return to the factory setting . . .
To brighten the image
RESTORE INITIAL SETTING
Press + and – simultaneously. The standard setting is
immediately restored and the Exposure level
indicator disappears.
3
–
06
+
06
To darken the image
Download from Www.Somanuals.com. All Manuals Search And Download.
23
White Balance Adjustment
MWB
This camcorder’s Automatic Color Temperature system
senses the color temperature of the ambient lighting for
automatic white balance adjustment. However, precise
color adjustment is not possible under the following
conditions:
•When an object is in various shades of the same color.
•When a predominantly red or brown object is being
shot outdoors.
In these cases, use the camcorder’s built-in preset filters
for white balance adjustment.
SELECT SHOOTING MODE
Set the Shooting Mode selector to “PRESET”.
1
SELECT FUNCTION
Press MWB (Manual White Balance) until the
2
required indication appears in the viewfinder.
“MWB” ....With a memorized personal White
................Balance setting (see below)
“
“
“
” .........Outdoors on sunny day
Shooting Mode Selector
” ........Outdoors on cloudy day
” ..........Light source is halogen or tungsten lamp
No indication
(Auto)
MWB sets the color temperature for the subject’s light
source so you can shoot with natural colors that are
unaffected by surroundings, even when there are
multiple subjects with different color temperatures.
MWB
MWB
SELECT SHOOTING MODE
Set the Shooting Mode selector to ”PRESET”.
1
White balance mode indicator
ADJUST FOCUS
Point the camcorder at a white, flat object such as a
2
3
sheet of white paper, and adjust focus manually
(੬ pg. 25).
ADJUST WHITE BALANCE
Press MWB until “MWB” appears, then press and
hold MWB for more than 3 seconds.
•“MWB” blinks in the viewfinder during
adjustment, then stops blinking but stays lit when
adjustment is complete.
NOTES:
● To switch to automatic white balance adjustment, press MWB until the indication disappears, or turn the
Shooting Mode selector to “FULL AUTO”.
● Re-adjust the White Balance mode when the lighting has changed, when the camcorder has been turned on and
off again, or when the Shooting Mode selector’s position has been changed.
● It is helpful to connect your camcorder to a color monitor when adjusting the white balance
(“Basic Connections” ੬ pg. 37).
● When adjusted by putting colored paper in front of the subject in step 2 (“ADJUST FOCUS”), this unit makes its
color temperature standard for automatic white balance. So you can enjoy shooting with different colors. For
example, when adjusting with red, blue or yellow colors, the image becomes the color which aproximates to
green, orange or purple respectively.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
24
Focusing
Auto Focus
The camcorder’s Full Range AF system offers continuous
shooting ability from close-up to infinity. However,
correct focus may not be obtainable in the situations
listed below (in these cases use manual focusing):
Focus
detection zone
•When two subjects overlap in the same scene.
•When illumination is low.*
•When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-color wall,
or a clear, blue sky.*
•When a dark object is barely visible in the viewfinder.*
•When the scene contains minute patterns or identical
patterns that are regularly repeated.
Shooting mode selector
FAR
NEAR
•When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast
background.
* The low-contrast warning “
viewfinder.
” appears in the
Focus Lock
This feature locks the focus in place, which is especially
helpful in the following situations:
•When things pass between your subject and the
camcorder. Engage the focus lock function to lock your
subject in before recording.
•When you want your subject to be focused, and to
appear in a corner of the screen. First, center on the
subject and focus using auto focus mode. Then engage
the focus lock function and move the camcorder until
the subject is where you want it.
SELECT SHOOTING MODE
Set the Shooting Mode selector to “PRESET”.
1
LOCK FOCUS
Press FAR or NEAR. The focus lock indication “
”
2
3
appears in the viewfinder.
RELEASE FOCUS LOCK
Press FAR and NEAR simultaneously. The
focus lock indication disappears.
NOTES:
● If the lens is smeared or blurred, accurate focusing is
not possible. Keep the lens clean, wiping with a piece
of soft cloth if it gets dirty. When condensation occurs,
wipe with a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens, zoom-out
first (੬ pg. 17). If zoomed-in in the auto focus mode,
the camcorder could automatically zoom out
depending on the distance between the camcorder and
the subject. *When Tele Macro is activated, the
camcorder will not zoom out automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Manual Focus
Shooting mode selector
FAR
NOTE:
NEAR
You should already have made the necessary viewfinder
adjustments (੬ pg. 10). If you haven’t, do so before
continuing.
SELECT SHOOTING MODE
Set the Shooting Mode selector to “PRESET”.
1
ADJUST FOCUS
TO FARTHER SUBJECT
Press and hold FAR. The Manual Focus indications
Power zoom lever
A
2
2
“
” appear and “ ” blinks.
Go to step 3.
B
TO NEARER SUBJECT
Press and hold NEAR. The Manual Focus indications
” appear and “ ” blinks.
“
Go to step 3.
LOCK FOCUS
Release FAR or NEAR. The focus
3
4
indication is replaced by the focus lock indication
“
” and the adjusted focus is locked in.
RELEASE MANUAL FOCUS MODE
Press FAR and NEAR simultaneously. The Manual
Focus mode is immediately released and the focus
lock indication disappears.
NOTES:
● Be sure to focus the lens in the maximum telephoto
position when you use the Manual Focus mode. If you
focus in on a certain subject in the wide-angle position,
sharply focused images cannot be obtained when
zoomed up because the depth-of-field is reduced at
longer focal lengths.
● When the focus level cannot be adjusted any farther or
closer, “ ” or “ ” will blink.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
26
Program AE With Special Effects
Shooting Mode Selector
FAR
Useful in making the picture look creative and attractive.
Effects can be selected during recording, as well as in
Record–Standby.
+
EFFECT/PROG.AE
SELECT SHOOTING MODE
Set the Shooting Mode selector to either “FULL
1
2
AUTO” or “PRESET”.
If you set to “FULL AUTO”, . . .
.... only the Cinema mode can be activated.
If you set to “PRESET”, . . .
.... you can choose any one of the 5 effects
available.
NEAR
–
SELECT EFFECT
If you set to “FULL AUTO”, . . .
.... pressing EFFECT/PROG.AE turns the Cinema
mode on and off.
If you set to “PRESET”, . . .
.... pressing EFFECT/PROG.AE brings up the Effect
menu. Press again to move the highlight bar to
the desired effect. Once you decide on an
effect, it is selected and activated, and its
indicator appears, within 2 seconds.
•If you started this procedure in the Record–
Standby mode, press RECORDING START/STOP
to begin recording at this point.
OFF
1
2
3
4
5
Cinema
Sepia
Twilight
Sports
DEACTIVATE EFFECT
HI.S 1/2000
When the Shooting Mode Selector is set to “FULL
AUTO”, . . .
3
.... press EFFECT/PROG.AE.
When set to “PRESET”, . . .
.... press EFFECT/PROG.AE to bring up the Effect
Menu, and press again to move the highlight bar
to “OFF”.
Effect menu
EFFECT/PROG. indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
27
INDICATION
MODE
EFFECT
Adds black bars to the top and bottom of the screen to produce a
cinema-like “16:9 wide-screen” effect.
CINEMA
The picture becomes sepia-tinted (reddish brown) monochrome,
creating the look of an old photograph.
SEPIA
Makes dusk and twilight scenes, etc. look more natural and
dramatic. White balance is set to “ ”. Press MWB if you want to
change the setting.
TWILIGHT
Automatically adjusts to high shutter speed (1/250 to 1/500) to
clearly capture fast-moving action with less blur. Clarity is
especially noticeable during slow motion or still playback on a
VCR. Great for sports, races, etc.
SPORTS
Captures even faster action than Sports effect.
HI-SPEED
SHUTTER
(1/2000)
NOTES:
● When the Sepia effect is activated, pressing MWB (manual white balance) has no effect.
● Certain effects cannot be used together with other functions. When an effect not usable in the present
situation is selected, its indicator blinks.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
28
Fade/Wipe
Shooting mode selector
These effects let you make pro-style scene
transitions.
SELECT SHOOTING MODE
Set the Shooting Mode selector to either “FULL
1
2
AUTO” or “PRESET”.
If you set to “FULL AUTO”, . . .
.... only the Black Fader mode is available.
FADE/WIPE
If you set to “PRESET”, . . .
.... you can choose any one of the effects available.
RESERVE EFFECT
If you set to “FULL AUTO”, . . .
.... pressing FADE/WIPE turns the Black Fader
mode on and off.
If you set to “PRESET”, . . .
.... pressing FADE/WIPE brings up the Fade/Wipe
menu. Press again to move the highlight bar to
the desired effect. Once you decide on an
effect, it is selected and reserved, and its
indicator appears, within 2 seconds.
OFF
BK
START RECORDING
1
2
3
4
5
Black Fader
Blue Fader
Mosaic Fader
Shutter Wipe
Slide Wipe
C
Press RECORDING START/STOP to start recording
3
4
and activate a fade- or wipe-in.
OR . . .
END RECORDING
Press RECORDING START/STOP to stop recording
and engage a fade- or wipe-out.
Fade/Wipe menu
DEACTIVATE EFFECT
When the Shooting Mode Selector is set to “FULL
AUTO”, . . .
.... press FADE/WIPE.
When set to “PRESET”, . . .
BK
.... press FADE/WIPE to bring up the Fade/Wipe
menu, then press again to move the highlight
bar to “OFF”.
NOTE:
When the Shooting Mode selector is set to “FULL AUTO”,
after a fade-in, Black Fader is no longer reserved. To
FADE/WIPE indication
B
K
reserve it for a fade-out, press FADE/WIPE. “ ” appears
in the viewfinder.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
B
K
BLACK FADER
Fades in/out to a black screen.
C
BLUE FADER
Fades in/out to a blue screen.
MOSAIC FADER
Gradually turns/returns the picture into/from a
mosaic pattern.
SHUTTER WIPE
A black screen moves in from the top and bottom,
closing over the image like a shutter, or a new
image pushes open the black screen vertically from
the center.
SLIDE WIPE
A black screen moves in from the left to gradually
cover the image, or a new image moves in from
right to left.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
30
Shooting mode selector
FAR
Using Menu For Detailed Adjustment
This camcorder is equipped with Multi-Function Control,
an easy-to-use, on-screen menu system that simplifies
many of the more detailed camcorder settings.
+
MENU
SELECT SHOOTING MODE
Set the Shooting Mode selector to “PRESET”.
1
ACCESS MAIN MENU SCREEN
Press MENU.
NEAR
2
–
SELECT FUNCTION
Press + or – to place the highlight bar on the desired
3
4
function.
MAKE SETTING
The setting procedure depends on the function you
select.
If you select, Tele Macro, Gain Up, Color Filter or
Tape Length, . . .
.... press FAR or NEAR to cycle through the choices
until the desired setting appears. Then go to step
8.
If you select Title or Date/Time, . . .
.... press NEAR to access the selection menu for
each function (Title – ੬ pg. 32; Date/Time –
੬ pg. 11).
Tele Macro
Gain Up
OFF
AGC
NOR.
T30
Color Filter
Tape Length
Title
Date/Time
Sub Menu
If you select “Sub Menu”, . . .
.... press NEAR to bring up the Sub Menu screen.
Go to step 5.
Main Menu screen
Tally
SELECT FUNCTION AT SUB MENU
ON
Press + or – to place the highlight bar on the desired
option, then press NEAR. The selected item begins
blinking.
Interval Timer OFF
5
6
7
Rec Time
OFF
07
JLIP ID NO.
CHANGE SETTINGS
Press + or – to change the displayed setting of the
selected function, then press FAR to enter your
choice. The selected item stops blinking.
Sub Menu screen
CLOSE SUB MENU
Press FAR, and setting is complete. The Sub menu
screen disappears and the Main Menu screen
reappears.
PAUSE
•To go directly past the Main Menu screen to the
normal screen, press MENU.
ࡗ CLOSE MAIN MENU
Press MENU. The normal screen reappears.
If any settings in the Main Menu have been
changed from the factory settings, this mark
appears in the viewfinder.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
31
MAIN MENU
Tele Macro
OFF
Usually set to this position.
ࡗ ON Usually the distance to a subject where the lens is in focus
depends on the zoom magnification. Unless there is a
distance more than 1m to the subject, the lens is out of focus
at the maximum telephoto setting. When set to “ON”, you
can shoot a subject as large as possible at a distance of
approx. 60 cm.
•Depending on the zoom position, the lens may go out of
focus.
Gain UP
AGC
Allows you to record a subject in a dark environment. It
delivers a brighter, if slightly coarse, picture.
ࡗ OFF Allows you to shoot dark scenes with no picture brightness
adjustment.
Color Filter
NOR
ࡗ RED ࡗ BLUE For normal shooting with no color adjustment.
Gives recording a reddish tint.
Gives recording a bluish tint.
Tape Length
Title
Allows you to set the tape length depending on the tape used (੬ pg. 12).
Allows you to superimpose a preset title onto a scene (੬ pg. 32).
Allows you to set the current date and time (੬ pg. 11).
Date/Time
= Factory setting
SUB MENU
Tally
ON
The tally lamp comes on to signal the start of recording.
The tally lamp remains off at all times.
OFF
Interval Timer and
Rec. Time
These features allow you to set the parameters for Self-Timer
(੬ pg. 34), Animation and Time-Lapse recording (੬ pg. 35).
JLIP ID NO.
This number will be necessary in the future when connecting the
camcorder to a device such as a computer using the JLIP terminal.
The numbers range from 01 — 99.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
32
+
Instant Titles
FAR NEAR
You can superimpose one of 8 preset titles, or a title you
made yourself, onto a scene.
SELECT SHOOTING MODE
Set the Shooting Mode selector to “PRESET”.
1
MENU
ACCESS MAIN MENU SCREEN
–
Press MENU.
2
ACCESS INSTANT TITLE MENU
SCREEN
Press + or – to move the highlight bar to “Title”, then
3
4
5
press NEAR. The Title menu appears.
SELECT PRESET TITLE
Press + or – to move the highlight bar to the desired
title. (To create an original title, refer to page 33.)
DISPLAY PRESET TITLE
Tele Macro
Gain Up
Color Filter
Tape Length
Title
OFF
AGC
NOR.
T30
Press MENU. The Title menu disappears, and the
selected title is displayed on the screen.
Date/Time
Sub Menu
OFF
Happy Birthday
Our Vacation
Merry Christmas
A Special Day
Happy Holidays
Our New Baby
Wedding Day
Congratulations
(Set Character)
Congratulations
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Character Generator
+
You can enter an original title of up to 18 characters.
FAR NEAR
Perform steps 1, 2 and 3 of the “Instant Title” procedure
(੬ pg. 32) before continuing.
ACCESS CHARACTER SET MENU
Press + or – to move the highlight bar to “(Set
1
2
Character)”, then press NEAR. The Character Set
menu appears.
MENU
–
INPUT CHARACTERS
Press +, –, FAR or NEAR to move the blinking cursor
to the desired character, then press MENU. The
selected characters appear at the bottom of the
screen. Repeat as many times as desired (max. 18).
•To select the location of the next character, press
+, –, FAR or NEAR to move the blinking cursor to
the row of squares at the bottom of the screen,
then press FAR or NEAR to move the blinking
cursor underneath the desired location. Press +
when you’re done, and the blinking cursor returns
to the character grid.
OFF
Happy Birthday
Our Vacation
END CHARACTER SETTING
Merry Christmas
A Special Day
Happy Holidays
Our New Baby
Wedding Day
Congratulations
(Set Character)
Press +, –, FAR or NEAR to move the cursor to
“End”, then press MENU. The Character Set menu
disappears and the Preset Title menu reappears.
Press MENU to return to the normal screen.
3
NOTE:
To erase a character you entered mistakenly, place the
cursor by “Clear” by pressing +, –, FAR or NEAR, then
press MENU. All characters are deleted at once. Or, to
erase selected characters only, place the blinking cursor
at the character at the bottom you want to replace, then
press +/–. “ ” in the top left corner is highlighted.
SET : MENU KEY
A
K
U
È
.
B
L
C
D
N
E
O
Y
F
P
Z
G
Q
Ä
H
R
Ö
I
J
T
À
:
M
S
V W X
Ü
&
ࡖ 9
Ì
,
Ò
’
Ù
Ñ Æ Ø
Å
¿
–
/
!
?
0 1 2 3 4 5 6 7 8
I
L I
End
Clear
SET : MENU KEY
A
B
L
C
D
N
E
O
Y
F
P
Z
G
Q
Ä
H
R
Ö
I
J
T
À
:
K
U
È
.
M
S
V W X
Ü
&
ࡖ 9
Ì
Ò
’
Ù
Ñ Æ Ø
Å
¿
–
,
/
!
?
0 1 2 3 4 5 6 7 8
I
L I KE YOU
ࡖ End
Clear
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING Advanced Features (cont.)
34
Interval Timer Indicator
Self-Timer
Recording
Time Indicator
You can set the delay between pressing RECORDING
START/STOP and the actual start of recording. If you
secure the camcorder, you (or whomever is operating the
camcorder) can enter the scene before recording starts.
1min
1s
+
ENGAGE RECORD-STANDBY
FAR NEAR
MODE
Make sure the lens cover is open, then set the Power
switch to “CAMERA”.
1
2
3
4
SELECT MODE
Set the Shooting Mode selector to “PRESET”.
MENU
–
ACCESS MAIN MENU SCREEN
Press MENU.
ACCESS SUB MENU SCREEN
Press – to move the highlight bar down to “Sub
Menu”, then press NEAR. The Sub Menu screen
appears.
SET INTERVAL TIME
Tally lamp
Press – to move the highlight bar down to “Interval
Timer”, press NEAR, then press + or – to cycle
through the choices. Stop when the desired time
appears. Choose from “15S”, “30S”, “1min”,
“5min”, or select to turn the function “OFF”. Then
press FAR twice to return to the Main Menu screen.
5
START/STOP
INT. TIME
REC TIME
CLOSE MAIN MENU
RM-V705U (provided)
Press MENU.
6
7
START DELAYED RECORDING
Tele Macro
Gain Up
OFF
AGC
NOR.
T30
Press RECORDING START/STOP. If you set the tally
lamp to “ON” (੬ pg. 31), it begins blinking, and
the blinking frequency increases about 5 seconds
before recording is to start. Once recording begins,
the lamp stops blinking but stays lit.
Color Filter
Tape Length
Title
Date/Time
Sub Menu
To Release Self-Timer . . .
.... while the tally lamp is blinking, press RECORDING
START/STOP to stop the blinking, then set “Interval
Timer” to “OFF” or press INT. TIME on the remote
control until “ ” disappears.
Main Menu Screen
Tally
ON
.... while the tally lamp is lit but not blinking, press set
“Interval Timer” to “OFF” or press INT. TIME on the
remote control until “ ” disappears.
Interval Timer OFF
Rec Time
OFF
07
JLIP ID NO.
NOTE:
Instead of performing steps 2 – 6, you can set the interval
time by pressing INT. TIME on the remote control.
Sub Menu Screen
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Animation
Time-Lapse
Give stationary scenes or objects an illusion of
movement. This function allows you to shoot a
series of pictures, each slightly different, of the same
object for a brief period of time.
You can record sequentially at preset time spans.
Leaving the camcorder aimed at a specific subject,
you can record subtle changes over an extended
period of time.
ENGAGE RECORD–STANDBY
ENGAGE RECORD–STANDBY
MODE
MODE
Make sure the lens cover is open, then set the
power switch to “CAMERA”.
Make sure the lens cover is open, then set the
power switch to “CAMERA”.
1
2
3
1
SET RECORDING SPEED
Set SP/EP to SP (੬ pg. 13).
2
SET RECORDING SPEED
Set SP/EP to SP (੬ pg. 13).
SET RECORDING TIME
SET RECORDING TIME
Press REC TIME on the remote control. There
Press REC TIME on the remote control. Four
choices are available, and they appear in the
following order (each time REC TIME is
pressed): 1/4S (one-fourth of a second), 1/2S
(one-half of a second), 1S (one full second) and
5S (five seconds). Press again to release the
Animation mode.
3
are four choices available, and they appear in
the following order (each time REC TIME is
pressed): 1/4S, 1/2S, 1S, and 5S. Press again to
reset.
•You can also set the recording time in the
Sub Menu screen. Press “–” to move the
highlight bar down to “Rec Time”, and press
NEAR, then press + or – to cycle through the
choices.
•You can also set the recording time in the
Sub Menu screen (੬ pg. 32). Press “–” to
move the highlight bar down to “Rec Time”,
press NEAR, and press + or – to cycle
SET INTERVAL BETWEEN
RECORDINGS
through the choices. Then press MENU.
Press INT. TIME on the remote control. There
are five choices available, and they appear in
the following order (each time INT. TIME is
pressed): OFF, 15S, 30S, 1 min, and 5 min.
Press again to reset.
START RECORDING
4
Press RECORDING START/STOP after focusing
on the subject. The recording stops
4
automatically after the selected period of time.
•You can also set the interval time in the Sub
Menu screen. Press “–” to move the highlight
bar down to “Interval Time”, press NEAR,
and press + or – to cycle through the choices.
•Exposure control (੬ pg. 22), manual
focusing (੬ pg. 25) and D.I.S. settings
(੬ pg. 22) should be performed at this point.
Once you perform step 5, these settings
cannot be changed.
ASSEMBLE SERIES OF
PICTURES
Repeat steps 3 and 4 for the desired number of
5
6
7
pictures.
CHECK YOUR WORK
Play back the series of pictures to see if the
results were satisfactory.
START TIME-LAPSE
RECORDING
RELEASE ANIMATION MODE
Press REC TIME until “ ” disappears from the
viewfinder, or set “Rec Time” in the Sub Menu
pscreen to “OFF”.
Press RECORDING START/STOP. Recording
and intervals alternate automatically.
5
6
RELEASE TIME-LAPSE MODE
NOTES:
To release when the tally lamp is not blinking,
press INT. TIME and REC TIME repeatedly
until “ ” and “ ” disappear. To release
when the tally lamp is blinking, press
RECORDING START/STOP to stop the
blinking, then press INT. TIME and REC TIME
repeatedly until “ ” and “ ” disappear, or
set “Interval Timer” and “Rec Time” in the Sub
Menu screen to “OFF”.
● For best results, make sure the camcorder is
secured when shooting in Animation or
Time-Lapse mode.
● Fade-in/out cannot be performed during
Animation or Time-Lapse shooting.
● Before performing other operations following
Animation or Time-Lapse recording, make sure
the Animation or Time-Lapse mode is deactivated.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK Using The Cassette Adapter
36
Cassette Adapter (VHS PlayPak)
Use this to play back a VHS-C video cassette recorded
with this camcorder. It is fully compatible with any VHS
video cassette recorder. The C-P7U adapter is battery
powered and automatically performs tape loading and
unloading.
+
INSERT BATTERY
Slide the battery cover up to remove it, and install
one “AA(R6)” size battery as shown in the
illustration at left. Then reattach the cover.
1
2
3
VCR
INSERT CASSETTE IN ADAPTER
Slide the latch to open the adapter compartment
door, then insert the cassette and close the
compartment door.
Compartment door
PLAY BACK ON CONNECTED VCR
Load the cassette adapter into the VCR and play the
tape back as you would any other.
REMOVE CASSETTE FROM
ADAPTER
Slide the latch and the compartment door opens
automatically. Then insert your finger in the hole on
the underside of the adapter as shown in the
4
Sliding latch
Reels
illustration at left, push up and remove the cassette.
Compact video cassette
NOTES:
● During tape loading and unloading, do not touch the
reels for safety and tape protection.
● During special-effect playback (slow motion, still
frame, etc.), the picture may vibrate or noise bars may
appear on the screen.
● To record on a VCR using a compact cassette and the
adapter, cover the adapter’s recording safety hole with
adhesive tape.
Recording safety hole
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK Basic Connections
37
There are three basic types of connections. When making
the connections, refer also to your VCR and TV
instruction manuals.
Connection To A VCR [A]
(Editing, Dubbing and Playback)
NOTE:
Use the optional Audio and Video cables.
To AUDIO
and VIDEO
connectors
CONNECT CAMCORDER TO VCR
Audio and Video
cables (optional)
As shown in the illustration at left, connect the
1
optional Audio and Video cables between the
AUDIO and VIDEO connectors on the camcorder
and those on the VCR.
A
B
To AUDIO and
VIDEO IN
connectors
SUPPLY POWER
Turn on the camcorder, the VCR and the TV.
2
3
SELECT MODE
VCR
Set the VCR to its AUX input mode, and set the TV
to its VIDEO mode or channel 3.
Antenna
Connection To A TV With A/V Input
Connectors [B] (Playback ONLY)
NOTE:
Use the optional Audio and Video cables.
CONNECT CAMCORDER TO TV
To AUDIO, VIDEO and
DC OUT connectors
As shown in the illustration at left, connect the
1
2
optional Audio and Video cables between the
AUDIO and VIDEO connectors on the camcorder
and those on the TV.
RF unit RF-V5U
(optional)
SELECT MODE
Set the TV to its VIDEO or AV mode (as specified in
its instructions).
NOTES:
Connection To A TV With NO A/V Input
Connectors (Playback ONLY)
● It is recommended to use the AC Power
Adapter/Charger as the power supply instead
of the battery pack.
NOTE:
● To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder’s Power switch to “CAMERA”,
then set your TV to the appropriate input
mode.
Use the optional RF-V5U RF unit.
* Refer to the RF-V5U instruction manual for connection
procedure.
● If you have a TV or speakers that are not
specially shielded, do not place the speakers
adjacent to the TV as interference will occur
in the camcorder playback picture.
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK Basic Playback
38
NOTE:
PLAY/PAUSE
STOP
Make sure you connect your camcorder as directed in
“Basic Connections” (੬ pg. 37).
LOAD A CASSETTE
Slide EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
FF
REW
1
SELECT MODE
Set the Power switch to “PLAY”. The Power On
indicator lights.
2
3
4
PLAYBACK
Press PLAY/PAUSE. The playback picture appears in
the viewfinder and the connected TV.
STOP PLAYBACK
Press STOP.
Rewind or Fast-forward the tape
Press REW to rewind, or FF to fast-forward the tape
POWER
during Stop mode.
NOTE:
The camcorder shuts off automatically after about 5
minutes in STOP mode. To turn on again, set the Power
switch to “POWER OFF”, then to “PLAY”.
M–1:23:45
Tape counter
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK Features
39
To eliminate noise bars that appear
on the screen.
TRACKING
COUNTER R/M
PLAY/PAUSE
FEATURE:
PURPOSE:
Manual Tracking
OPERATION:
NOTES:
1) Press either TRACKING button as
many times as necessary for best
picture.
● To reset TRACKING to the original
preset, press both TRACKING
buttons simultaneously.
REW
● Manual Tracking may not work
with tapes recorded on other VCRs
or camcorders.
FF
STOP
FEATURE:
Still Playback
PURPOSE:
OPERATION:
To pause during playback.
1) Press PLAY/PAUSE during
playback.
2) To resume normal playback, press
PLAY/PAUSE again.
NOTE:
Noise bars appear and pictures may
become monochrome during Still
Playback. This is normal.
FEATURE:
PURPOSE:
Shuttle Search
To allow high-speed search in either
direction.
OPERATION:
Forward Search
1) Press FF during playback. (Speed is
5 times normal in SP, and 15 times
normal in EP mode.)
Reverse Search
1) Press REW during playback.
(Speed is as noted above.)
NOTE:
Noise bars appear and pictures may
become monochrome or darken in
Shuttle Search. This is normal.
FEATURE:
PURPOSE:
Counter Memory Function
To make it easier to locate a specific
tape segment.
OPERATION:
1) Press COUNTER R/M and hold for
more than 2 seconds. The counter
resets to “0:00:00”.
2) Press COUNTER R/M. “M”
appears.
PLAY
PAUSE
FF
3) After recording or playback, press
STOP, then REW. The tape
automatically stops at or close to
0:00:00.
REW
RM-V705U (provided)
4) Press PLAY/PAUSE to start
playback.
NOTES:
● The counter memory functions in
the FF and REW modes.
● To disable Counter Memory
Function, press COUNTER R/M so
the “M” disappears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
40
Tape Dubbing
CONNECT EQUIPMENT
Following the illustration at left, connect the
camcorder and the VCR.
1
2
PREPARE FOR DUBBING
PLAY/PAUSE
Set the camcorder’s Power switch to “PLAY”, turn
on the VCR’s power, and insert the appropriate
cassettes in the camcorder and the VCR.
SELECT VCR MODE
Engage the VCR’s AUX and Record-Pause modes.
3
4
FIND EDIT-IN POINT
To AUDIO and
VIDEO OUT
connectors
Power switch
Engage the camcorder’s Play mode to find a spot
just before the edit-in point. Once it’s reached, press
PAUSE on the camcorder.
START EDITING
Audio and Video
cable (optional)
Press PLAY on the camcorder and engage the VCR’s
Record mode.
5
6
7
STOP EDITING TEMPORARILY
Engage the VCR’s Record-Pause mode and press
PAUSE on the camcorder.
To AUDIO and
VIDEO IN
connectors
EDIT MORE SEGMENTS
Repeat steps 4 through 6 for additional editing, then
stop the VCR and camcorder when finished.
VCR (Recording deck)
Random Assemble Editing [R.A.Edit]
Create edited videos easily using your camcorder as the
source player. You can select up to 8 “cuts” for automatic
editing, in any order you like. R.A.Edit is more easily
performed when the optional RM-V700U MBR
(Multi-Brand Remote) is set to operate with your brand of
VCR (see VCR CODE LIST), but can also be performed by
operating the VCR manually.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
41
SET REMOTE/VCR CODE
SET REMOTE TO OPERATE VCR
Turn off the power to the VCR and point the remote
toward the VCR’s infrared sensor. Then, referring to
the chart at left, press and hold MBR SET, and press
button (A) and then (B).
MBR SET
VCR CTL
1
2
1
4
7
2
5
8
3
6
9
0
•The code is automatically set once you release the
MBR SET button, and the VCR’s power comes on.
RM-V700U (optional)
VCR CODE LIST
OPERATE THE VCR
Make sure the VCR’s power is on. Then, while
holding VCR CTL, press the button on the remote for
the desired function. The functions the remote can
control are PLAY, STOP, PAUSE, FF, REW and VCR
REC STBY (you don’t need to press VCR CTL for this
one).
VCR BRAND BUTTONS
VCR BRAND BUTTONS
NAME
PHILIPS
NAME
GE
(A) (B)
(A) (B)
1
9
9
9
6
6
9
9
9
9
1
7
7
6
6
3
3
1
9
1
9
9
9
1ꢀ
2ꢀ
`ꢀ
4
6ꢀ
3
1ꢀ
6ꢀ
3
5ꢀ
1ꢀ
1ꢀ
6
7ꢀ
8
7ꢀ
8
9ꢀ
5ꢀ
1ꢀ
4ꢀ
1ꢀ
6
1
3
2ꢀ
3
PANASONIC
RCA
1
1
1
9
1
3ꢀ
7ꢀ
1ꢀ
4ꢀ
8ꢀ
HITACHI
You’re now ready to try Random Assemble Editing.
JVC
A
B
C
ꢀ
9
9
6
6
9
2ꢀ
4ꢀ
6ꢀ
3ꢀ
`
IMPORTANT
Although the MBR is compatible with JVC VCRs and
those of many other makers, it may not work with yours
or may offer limited functions.
MAGNAVOX
SANYO
SHARP
SONY
3
3
6ꢀ
5
MITSUBISHI
NEC
NOTES:
1
1
5ꢀ
`
● If the VCR’s power doesn’t come on in step 1, try
another code from the chart.
6
6
3
3
5ꢀ
`ꢀ
9ꢀ
1ꢀ
● Some brands of VCR don’t come on automatically. In
this case, turn the power on manually and try step 2.
● If the RM-V700U is not able to control the VCR, use
the controls on the VCR.
PHILIPS
ꢀ
TOSHIBA
ZENITH
6
6
9ꢀ
1
1
6
MAKE CONNECTIONS
CONNECT TO . . .
A
JVC VCR EQUIPPED WITH REMOTE
1
PAUSE TERMINAL
Connect the editing cable to the Remote PAUSE
terminal.
B
JVC VCR NOT EQUIPPED WITH REMOTE
2
PAUSE TERMINAL
Connect the editing cable to the R.A. EDIT connector.
C
NON-JVC VCR WITH NEITHER
2
Connect the editing cable to the RM-V700U’s
Pause-In jack.
All other connections are as shown in the illustration
on page 42.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING (cont.)
42
REW/FF CANCEL
PREPARE CAMCORDER
Insert a recorded tape and set the Power switch to
“PLAY”.
IN/OUT
2
3
R.A. EDIT
PREPARE VCR
Turn the power on, insert a recordable tape and
engage the AUX mode (refer to VCR’s instructions).
PLAY/PAUSE
STOP
SELECT SCENES
ACCESS R.A. EDIT COUNTER
DISPLAY
Press PLAY/PAUSE, then press R.A. EDIT and the
counter display appears in the viewfinder and the
screen of the connected TV.
1
2
3
To JLIP
To AUDIO and
VIDEO out
connectors
REGISTER BEGINNING OF SCENE
Press REW or FF to locate the beginning of a scene
you want, then press IN/OUT to register that point.
The data appears under IN on the display.
Editing cable
(optional 3.5 ø
Audio and Video
cable (optional)
mini-plug cable)
REGISTER END OF SCENE
Press REW or FF to locate the end of the scene and
press IN/OUT to register it. The data appears under
OUT on the display. The total time of the registered
scene(s) is displayed at the bottom of the screen.
A
C
B
To Remote
PAUSE
To AUDIO and
VIDEO IN
REGISTER ADDITIONAL SCENES
connectors
To Pause-In
Repeat steps 2 and 3 for each additional scene
4
5
(as many as 8).
VCR (Recording deck)
MAKE CORRECTIONS
Press CANCEL during steps 2 and 3 to erase the
most recently registered point.
CANCEL
RM-V700U
(optional)
NOTES:
● The RM-V700U can be used to operate other camcorder
functions as well. Point the RM-V700U at the camcorder’s
remote sensor and press any of the following buttons
(function apears in parentheses):
ON/OFF
VCR REC STBY
IN/OUT
— ON/OFF (camcorder R.A. EDIT)
— IN/OUT (camcorder IN/OUT)
— CANCEL (camcorder CANCEL)
IN
0:00:25
OUT
--:--:--
IN
OUT
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
0:00:25
0:03:18
0:02:33
0:04:11
0:01:05
0:03:31
0:02:53
--:--:--
● There must be at least one second between an in-point and
its corresponding out-point.
● To ensure correct operation, leave at least 15 seconds open
between scenes.
● Blank portions of tape cannot be registered as in-points or
out-points.
COUNTER
TOTAL
0:00:25
0:00:00
COUNTER
TOTAL
0:04:11
0:01:13
● If it takes more than 5 minutes to search for an in-point, the
VCR’s Record-Pause mode is cancelled and editing doesn’t
take place.
● Pressing R.A.EDIT clears all in- and out-points from
memory.
● Leave a small margin for error around each in-point to
ensure the scene is recorded in its entirety.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
AUTOMATIC EDITING TO VCR
ORIGINAL TAPE (camcorder)
1
IN
3
2
IN
ENGAGE VCR’S RECORD–PAUSE
MODE
OUT
IN OUT
OUT
Point the remote control toward the VCR’s infrared
sensor and press VCR REC STBY, or manually
engage the VCR’s Record-Pause mode.
1
2
3
BEGIN AUTOMATIC EDITING
Press EDIT on the camcorder, and the previously
selected scenes are copied to the VCR in the
specified order.
EDITED TAPE (VCR)
EDIT STOP
END AUTOMATIC EDITING
When all selected scenes have been copied, the
camcorder and VCR enter the still or pause mode.
Press STOP on both units.
•When finished editing, be sure to disconnect the
editing cable and the audio/video cable.
NOTES:
C
● If you performed step 1 on page 41
(“MAKE CONNECTIONS”), keep the remote control
pointed at the VCR during editing.
● The on-screen display only appears while the
camcorder searches for each scene.
● There may be noise at in- or out-points on the edited
tape with certain VCRs.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING (cont.)
44
Insert Editing
COUNTER R/M
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in- and out-points. The
original audio remains unchanged.
NOTE:
Use the RM-V705U remote control unit to perform this
procedure.
SELECT MODE
Set the Power switch to “PLAY”.
1
FIND EDIT-OUT POINT
Locate the point and press PAUSE on the camcorder
2
3
or the remote control.
RESET COUNTER
Press and hold COUNTER R/M for more than
2 seconds to reset the tape counter, then press for
less than 1 second and make sure “M” appears in
the viewfinder.
POWER
FIND EDIT-IN POINT
w
Insert editing
M–0:12:34
Press REW to go a little beyond the beginning of the
scene you want to replace, press PLAY to view the
recorded tape, and press PAUSE at exactly at the
point where the new scene should start.
indicator
4
5
Tape Counter
ENGAGE INSERT EDITING MODE
Press and hold INSERT, and without releasing
INSERT, press and release PAUSE. The Insert
mode is engaged, and the scene the camcorder is
aimed at appears on the screen.
Viewfinder
BEGIN INSERT EDITING
Press RECORDING START/STOP. When the counter
reaches “0:00:00”, editing stops automatically and
the camcorder enters the Insert-Pause mode.
6
7
END INSERT EDITING
Press STOP.
•If a Fade/Wipe effect was in use during Insert
Editing, wait about 10 seconds after pressing STOP
before performing other operations.
PLAY
NOTES:
PAUSE
REW
● After step 5, Retake (੬ pg. 18) can be performed.
● The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
● Only video signal is recorded in the Insert Editing
mode.
INSERT
RM-V705U (provided)
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Audio Dubbing
Audio dubbing indicator
You can record a new soundtrack on a prerecorded tape
(normal audio only).
e
Viewfinder
M-0:05:20
** Perform steps 1, 2 and 3 of the Insert Editing procedure
(੬ pg. 44) before continuing.
•The sound comes from the built-in mike.
FIND EDIT-IN POINT
Press REW to go a little beyond the beginning of the
1
scene onto which you want to dub new audio, press
PLAY to view the recorded tape, then press PAUSE
at exactly the point where dubbing should start.
Mike
ENGAGE AUDIO DUB STANDBY
MODE
Press and hold A. DUB, and without releasing
A. DUB, press and release PAUSE.
2
3
4
BEGIN AUDIO DUBBING
Press PLAY/PAUSE. When the counter reaches
“0:00:00”, Audio Dubbing stops automatically and
the camcorder enters the Audio Dub-Standby mode.
END AUDIO DUBBING
Press STOP.
PLAY
REW
NOTE:
PAUSE
● Do not press FF or REW during Audio Dub-Standby, or
the edit points will not be accurate.
● If the mike is too close to the TV, or if the TV’s volume
is too high, whistling or howling may occur.
A.DUB
RM-V705U (provided)
NOTES (for Insert Editing and
Audio Dubbing):
● Insert Editing and audio Dubbing may not work
correctly if the tape contains blank segments, or if the
recording speed was changed during the original
recording.
● To edit/dub onto a tape with the recording safety tab
removed, cover the hole with adhesive tape.
● Do not press STOP during Insert Editing or Audio
Dubbing, or the edit points will not be accurate.
● During Insert Editing and Audio Dubbing, when Insert–
Pause or Audio Dub–Standby is engaged, the counter
may go slightly past “0:00:00”. Recording, however,
stops at exactly 0:00:00.
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MAINTENANCE
46
After Use
LENS COVER
open/close switch
Set the Power switch to “POWER OFF” to turn off
the camcorder.
1
2
3
4
5
Slide EJECT to open the cassette holder, then remove
the cassette.
Close and lock the cassette holder by pressing
PUSH.
Press BATT. RELEASE to remove the battery pack.
Slide the LENS COVER open/close switch to close
the lens cover.
Set to “POWER OFF”
Cleaning The Camcorder
BATT. RELEASE
CLEAN EXTERIOR
Wipe gently with a soft cloth.
1
EJECT
CLEAN LENS
Blow it with a blower brush, then wipe gently with
2
3
4
5
lens cleaning paper.
REMOVE EYEPIECE
PUSH
Turn the eyepiece counterclockwise and pull it out.
Remove
CLEAN VIEWFINDER
Remove dust using a blower brush.
RE-ATTACH EYEPIECE
Align the marks, re-attach the eyepiece and turn it
clockwise.
NOTES:
● Avoid using strong cleaning agents such as benzine or
alcohol.
● Cleaning should be done only after the battery pack
has been removed or other power units have been
disconnected.
Marks
● Mold may form if the lens is left dirty.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
47
SYMPTOM
POSSIBLE CAUSE(S)
POWER
No power is supplied.
● The battery pack has not been attached correctly
(੬ pg. 8).
● The battery pack is not charged (੬ pg. 8).
● The power supply has not been correctly connected
(੬ pg. 9).
The power suddenly goes off and
doesn’t come back on by itself.
● The battery pack has completely discharged.
● Remove the cassette and disconnect the power source,
then after a few minutes, try turning the power back on. If
it still doesn’t come on, consult your nearest JVC dealer.
RECORDING
Recording cannot be performed.
● The recording tape’s Erase Protection tab is missing.
Cover the hole with adhesive tape. (Some tapes have
sliding tabs. In this case, check the position of the tab.)
Recording does not start.
● The camcorder Power switch has not been set to
“CAMERA” (੬ pg. 16).
PLAYBACK
The tape is running, but there’s no
playback picture.
● The TV has not been set to its VIDEO mode or channel.
● If A/V connection is used, the TV’s VIDEO/TV switch has
not been set to VIDEO.
● The RF unit has not been set to the correct channel.
Noise bars appear in the playback
picture.
● Manual Tracking has not been performed (੬ pg. 39).
Playback picture is blurred or
interrupted.
● The video heads are dirty or worn out. Consult your
nearest JVC dealer for head cleaning or replacement.
The counter indication is blurred
during Still playback.
● This is normal.
TAPE TRANSPORT
The tape stops during fast-forward or
rewind.
● The Counter Memory Function has been activated
(੬ pg. 39).
Rewinding or fast-forwarding cannot
be performed.
● The tape is already fully wound on one reel or the other.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (cont.)
48
SYMPTOM
POSSIBLE CAUSE(S)
OTHER
The tape won’t eject.
● The battery pack is running low.
Some functions are not available.
● The Shooting Mode selector is set to “FULL AUTO“.
Vertical white lines appear when
shooting a very bright object.
● This sometimes occurs when the contrast between the
background and the object is great. It is not a defect of
the camcorder.
Bright, crystal-shaped spots appear
in the viewfinder.
● Sunlight is directly entering the lens.
The picture is blurred in the Quick
Review or Retake mode.
● This is normal while recording in the EP mode. Some noise
may be present while recording in the SP mode (੬pg. 13).
An error number (E03) appears in
the viewfinder.
● Turn the camcorder’s power off, then disconnect the
power source. After a few minutes, try turning the power
on again. If the error number still appears in the view-
finder, consult your nearest JVC dealer.
The image is out of focus.
● The diopter needs to be adjusted (੬ pg. 10).
● The scene being shot is adversely affecting the operation
of Auto Focus (੬ pg. 24).
A character generator title and the
date and time displays disappear
from the viewfinder.
● If you remove the power source from the camcorder while
the power is on, all settings and selections are erased.
Make sure to turn the camcorder’s power off before
disconnecting the power source.
Even though the Lens Cover is open,
the Lens Cover Warning indicator
blinks.
● The Lens Cover Warning indicator may blink when the
camcorder is used in dark areas, regardless of the position
of the Lens Cover.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit
(battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and
proceed as usual from the beginning.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX Controls
49
$ % ^ &
* (
! @ #
) q w e r
1 2
3
t
y
u
9
0
4 5 6 7 8
Controls
1 Multi-Function Control
% Recording Mode [SP/EP] Select
[FAR/NEAR/+/– Buttons] ...................... ੬ pg. 11
2 EFFECT/PROG.AE Button .................... ੬ pg. 26
3 PUSH Button......................................... ੬ pg. 5
4 Shooting Mode Selector ...................... ੬ pg. 11
5 DISPLAY Button .................................. ੬ pg. 20
6 FADE/WIPE Button .............................. ੬ pg. 28
7 MENU Button ..................................... ੬ pg. 11
8 D.I.S. [Digital Image Stabilizer]
Button ................................................. ੬ pg. 13
COUNTER R [Reset]/M [Memory]
Button ................................................. ੬ pg. 39
^ EDIT Button ........................................ ੬ pg. 43
& TRACKING +/– Buttons ....................... ੬ pg. 39
* R.A.EDIT IN/OUT Button .................... ੬ pg. 42
( R.A.EDIT Button .................................. ੬ pg. 42
) REW Button......................................... ੬ pg. 38
RETAKE R [Quick Review] Button ....... ੬ pg. 17
q FF Button ............................................ ੬ pg. 38
RETAKE F Button ................................. ੬ pg. 18
w R.A.EDIT CANCEL Button ................... ੬ pg. 42
e STOP Button ......................................... ੬ pg. 5
r PLAY/PAUSE Button .............................. ੬ pg. 5
t BATT. [Battery] RELEASE Switch ............ ੬ pg. 5
y Recording Start/Stop Button.................. ੬ pg. 5
u POWER Switch ................................... ੬ pg. 10
Button .................................................੬ pg. 22
9 EJECT Switch ......................................... ੬ pg. 5
0 LIGHT ON/AUTO/OFF select switch ....੬ pg. 19
! Diopter Adjustment ............................. ੬ pg. 10
@ QUICK REC Button ............................. ੬ pg. 21
# Power Zoom Lever .............................. ੬ pg. 17
$ MWB [Manual White Balance]
Button .................................................੬ pg. 23
Download from Www.Somanuals.com. All Manuals Search And Download.
50
I
O
P
a
T
Y
s
d
R
i o p Q W
f
U
E
Connectors
Other Parts
T Video Light.......................................... ੬ pg. 19
Y Microphone ........................................ ੬ pg. 45
i DC IN Jack ............................................ ੬ pg. 9
o JLIP (Joint Level Interface Protocol) Connector.
•Connect the Editing Cable when performing
Random Assemble Editing (੬ pg. 42).
U Infrared beam sensor window ............. ੬ pg. 15
(Be careful not to cover this area; built-in
here is the sensor necessary for shooting.)
•In the future, it will be used to connect the
camcorder to a device such as a personal
computer.
I Shoulder Strap Eyelets ......................... ੬ pg. 14
O Clock Battery Compartment ................ ੬ pg. 10
P Battery Pack Mount ...............................੬ pg. 8
a Electronic Viewfinder .......................... ੬ pg. 10
s LENS COVER Switch ............................. ੬ pg. 5
d Grip Strap ........................................... ੬ pg. 14
f Tripod Mounting Socket ...................... ੬ pg. 14
p VIDEO Out Jack .................................. ੬ pg. 37
Q RF DC OUT Jack .................................੬ pg. 37
W AUDIO Out Jack .................................੬ pg. 37
Indicators
E Tally Lamp .......................................... ੬ pg. 16
R Power On Indicator............................. ੬ pg. 16
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX Viewfinder
51
1 2 3
4
5 6 7
T40
112min
REC EP
1min
1/4s
W
e
r
8
9
0
!
@
#
w
q
)
(
*
+
02
MWB
PAUSE
ࡗ INDEX
T
TAPE END
Congratulations
DEC 25. 96
PM 4:28:34
& ^
%
$
Viewfinder Indications
1 Remaining Tape Time ..........................੬ pg. 16
2 Recording Mode (SP/EP) Indicator ....... ੬ pg. 13
3 Interval Timer Indicator. ......................੬ pg. 34
4 Recording Time Indicator .................... ੬ pg. 35
5 Tape Length Display ............................ ੬ pg. 12
6 Battery Pack Remaining Power
# Clock Warning
Once the power is turned on and the indicator
blinks for about 10 seconds, perform the date
and time settings (੬ pg. 11). After setting is
complete, turn the power off and disconnect the
power source. If you re-connect it and turn the
power on and the indicator is blinking, that
means that the clock (lithium) battery is either
not installed or has discharged. Install, or replace
the old battery with, a new one (੬ pg. 10).
$ Time Display ....................................... ੬ pg. 20
% Instant Title Display ............................. ੬ pg. 32
^ Tape End Display ................................ ੬ pg. 16
Appears when the end of the tape is reached
during playback, recording or fast-forward.
& Date Display ....................................... ੬ pg. 20
* Condensation Warning
Indicator ............................................... ੬ pg. 8
Changes as follows according to the battery
pack’s remaining power level:
“
”. When the power is
almost gone, the indicator blinks, then the unit
shuts off. Replace the battery pack with a fully
charged one.
(Note: The symbol containing 3 darkened
squares —
— does not necessarily mean
that the battery pack is fully charged.)
7 Cassette Indicator
When this indication appears, all functions are
disabled. Turn the unit off (without removing the
power source) for a few hours, and when you
turn it on again the indicator should disappear.
( Main Menu Setting Change
Indicator ............................................. ੬ pg. 31
) FADE/WIPE indicator .......................... ੬ pg. 28
q D.I.S. (Digital Image Stabilizer)
Blinks when no cassette inserted;
remains steadily lit when cassette inserted.
8 Focus Indicator ...................................੬ pg. 24
9 Exposure Level Display ....................... ੬ pg. 22
0 White Balance Mode Indicator............ ੬ pg. 23
! Record–Standby Mode Indicator ......... ੬ pg. 16
@ Index Code Marking............................ ੬ pg. 18
Indicator ............................................. ੬ pg. 22
w EFFECT/PROG.AE indicator................. ੬ pg. 26
e Recording Indicator ............................. ੬ pg. 16
r Zoom Indicator Bar ............................. ੬ pg. 17
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX Terms
52
A
P
AC Power Adapter .................................. pg. 9
Playback ................................................. pg. 36
Program AE with Special Effects .............. pg. 27
Provided Accessories .............................. pg. 6
Animation Recording .............................. pg. 35
Audio Dubbing ....................................... pg. 45
Auto Focus.............................................. pg. 24
Q
B
Quick Rec............................................... pg. 21
Quick Review ......................................... pg. 17
Battery Pack ............................................ pg. 8
Brighten the Image .................................. pg. 22
R
C
Random Assemble Editing ....................... pg. 40–43
Record-Standby ...................................... pg. 16
Recording, Advanced Features ................ pg. 20–35
Recording ............................................... pg. 16
Recording, Start/Stop............................... pg. 16
Recording Mode Setting.......................... pg. 13
Remote Control Unit ............................... pg. 15
Remove Cassette ..................................... pg. 13
Retake..................................................... pg. 18
Rewind Tape ........................................... pg. 38
Car Battery .............................................. pg. 9
Cassette Adapter ..................................... pg. 36
Character Generator ............................... pg. 33
Charge Marker ........................................ pg. 9
Charging the Battery Pack ....................... pg. 8
Cinema Mode ......................................... pg. 27
Clock (Lithium) Battery ........................... pg. 10
Connection to a VCR/TV ......................... pg. 37
Contents ................................................. pg. 7
Counter Memory ..................................... pg. 39
S
D
Sepia Mode............................................. pg. 27
Shoulder Strap Attachment ...................... pg. 14
Shuttle Search ......................................... pg. 39
Specifications.......................................... pg. 55
Sports Mode............................................ pg. 27
Still Playback .......................................... pg. 39
Sub Menu ............................................... pg. 31
Darken the Image ................................... pg. 22
Date/Time Insert...................................... pg. 20
Date/Time Setting.................................... pg. 11
Digital Image Stabilizer ........................... pg. 22
Discharge the Battery pack...................... pg. 8
Diopter Adjust......................................... pg. 10
E
T
Erase Protection ...................................... pg. 13
Exposure Control .................................... pg. 22
Tape Counter .......................................... pg. 38
Tape Dubbing ......................................... pg. 40
Tape Length Setting ................................. pg. 12
Time-Lapse Shooting ............................... pg. 35
Tracking .................................................. pg. 39
Tripod Mounting ..................................... pg. 14
Twilight Mode ......................................... pg. 27
F
Fade-in/out ............................................. pg. 28
Fast-Forward Tape ................................... pg. 38
Focus Lock.............................................. pg. 24
G
V
Grip Adjustment...................................... pg. 14
Viewfinder Adjustment ............................ pg. 10
Viewfinder, Indications............................ pg. 51
H
W
High Speed Shutter Mode ....................... pg. 27
White Balance Adjustment ...................... pg. 23
Wipe in/out ............................................. pg. 28
I
Index Code Marking ............................... pg. 18
Insert Cassette ......................................... pg. 13
Insert Editing ........................................... pg. 44
Instant Titles ............................................ pg. 32
Interval Timer .......................................... pg. 34
Z
Zooming ................................................. pg. 17
M
Main Menu ............................................. pg. 31
Manual Focus ......................................... pg. 25
MBR Code Setting ................................... pg. 41
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
53
DANGER:
General Battery Precautions
Video Light
•When the C-P6U or C-P7U (cassette adapter) are
not functioning even when correctly operated, the
batteries are exhausted. Replace them with fresh
ones.
• The video light becomes extremely hot. Do not touch it
either while in operation or soon after turning it off,
otherwise serious injury may result.
• Do not place the camcorder into the carrying case
immediately after using the video light, since it remains
extremely hot.
•Use only the following batteries:
C-P6U or C-P7U..................... AA (R6) size
• When operating, keep a distance of about 30 cm
(1 ft.) between the video light and people or object.
• Do not use near flammable or explosive materials.
Please make note of the following rules for battery
use. When misused, batteries can leak or explode.
1. Refer to the C-P6U/C-P7U instructions when
replacing batteries.
2. Do not use old and new batteries together.
3. Do not use two different kinds of batteries.
Although sizes may be the same, voltages may
differ.
When using the AC Power Adapter/Charger in
areas other than the USA
Ⅲ The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from 110 V
to 240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit's power cord to an
AC wall outlet other than American National
Standard C73 series type use an AC plug adapter,
called a "Siemens Plug", as shown.
For this AC plug adapter, consult your nearest JVC
dealer.
4. Do not expose batteries to excessive heat as they
can leak or explode.
5. Do not dispose of batteries in a fire.
6. Remove batteries from the unit if it is to be stored
for an extended period to avoid battery leakage
which can cause malfunctions.
Plug adapter
Battery Packs
The supplied battery pack is a
nickel-cadmium battery. Before
using the supplied battery pack or
an optional battery pack, be sure to
read the following cautions:
INFORMATION
This device complies with Part 15 of FCC Rules. Operation
is subject to the following two
conditions:
1. To avoid hazard . . .
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
Change or modifications not approved by the party
responsible for compliance could void the user's authority
to operate the equipment. This equipment has been tested
and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
.... do not burn.
Terminals
.... do not short-circuit the terminals.
.... do not modify or disassemble.
.... use only specified chargers.
2. To prevent damage and prolong service
life . . .
.... do not subject to unnecessary shock.
.... avoid repeated charging without fully
discharging.
.... charge in an environment where
temperatures are within the tolerances shown
in the chart below. This is a chemical
reaction type battery—cooler temperatures
impede chemical reaction, while warmer
temperatures can prevent complete charging.
.... store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
.... avoid prolonged uncharged storage.
.... remove from charger or powered unit when
not in use, as some machines use current
even when switched off.
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician
for help.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS (cont.)
54
3. To prevent damage to the camcorder . . .
2. Avoid using the unit . . .
.... replace the battery pack when it begins to
deliver less recording time per charge.
.... in places subject to excessive humidity or
dust.
.... in places subject to soot or steam such as
near a cooking stove.
.... in places subject to excessive shock or
vibration.
.... near a television set.
NOTE:
It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging ................................... 10°C to 35°C
Operation ................................. 0°C to 40°C
Storage ...................................... –10°C to 30°C
.... near appliances generating strong magnetic
or electric fields (speakers, broadcasting
antennas, etc.).
.... in places subject to extremely high (over
40°C or 104°F) or extremely low (under 0°C
or 32°F) temperatures.
NOTES:
● Recharging time is based on room temperature of
20°C.
3. DO NOT leave the unit . . .
.... in places of over 50°C (122°F).
.... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
.... in direct sunlight.
● The lower the temperature, the longer recharging
takes.
Cassettes
.... in a closed car in summer.
.... near a heater.
To properly use and store your cassettes, be sure to
read the following cautions:
4. To protect the unit, DO NOT . . .
.... allow it to become wet.
1. During use . . .
.... make sure the cassette bears the VHS-C
mark.
.... drop the unit or strike it against hard objects.
.... subject it to shock or excessive vibration
during transportation.
.... keep the lens directed at extremely bright
objects for long periods.
.... direct the eyepiece of the viewfinder at the
sun.
.... carry it by holding the viewfinder.
.... swing it excessively when using the shoulder
strap.
.... be aware that recording onto prerecorded
tapes automatically erases the previously
recorded video and audio signals.
.... make sure the cassette is positioned properly
when inserting.
.... do not load and unload the cassette
repeatedly without allowing the tape to run
at all. This slackens the tape and can result in
damage.
.... do not open the front tape cover. This
exposes the tape to fingerprints and dust.
5. This camcorder features a built-in head
cleaner which automatically cleans the
heads and head drum when a cassette is
loaded or unloaded. If, however, the heads
become dirty and cause blurriness or
interruption in the playback picture,
consult your nearest JVC dealer.
2. Store cassettes . . .
.... away from heaters or other heat sources.
.... out of direct sunlight.
.... where they won’t be subject to unnecessary
shock or vibration.
.... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
.... vertically, in their original cases.
About moisture condensation . . .
•You have observed that pouring a cold liquid into
a glass will cause drops of water to form on the
glass‘ outer surface. This same phenomenon
occurs on the head drum of a camcorder when it
is moved from a cool place to a warm place, after
heating a cold room, under extremely humid
conditions or in a place directly subjected to the
cool air from an air conditioner.
Main Unit
1. For safety, DO NOT . . .
.... open the camcorder’s chassis.
.... disassemble or modify the unit.
.... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not
in use.
•Moisture on the head drum can cause severe
damage to the video tape, and can lead to internal
damage to the camcorder itself.
.... allow inflammables, water or metallic objects
to enter the unit.
.... remove the battery pack or disconnect the
power supply while the power is on.
.... leave the battery pack attached when the
camcorder is not in use.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL
55
VIDEO
Output
Format
: VHS NTSC standard
: 1 Vp-p, 75 ohms,
Power source
Power consumption
GR-AX910
Light on
: DC 6V
unbalanced (via VIDEO
out connector)
AUDIO
Output
: 8.9 W
: 5.9 W
: –8 dBs, 1 k-ohm
(via AUDIO out
connector)
Light off
GR-AX810
Light on
Light off
: 8.7 W
: 5.7 W
AC POWER ADAPTER/BATTERY CHARGER
(AA-V11U)
Signal system
Video recording system
Luminance
Color
: NTSC-type
Power requirement
: FM recording
: Converted sub-carrier
direct recording
* Conforms to VHS
standard
U.S.A. and Canada : AC 120 V`, 60 HZ
Other countries
: AC 110 V to
240 V`, 50/60 Hz
: 23 W
Power consumption
Output
Charge
VTR
Charging system
Cassette
Tape speed
SP
:
cassette
: DC 8.5 V
: DC 6.3 V
, 1.3 A
, 1.8 A
: Constant current, peak
detection, timer
controlled
: 33.35 mm/sec.
(1-5/16 ips)
: 11.12 mm/sec. (7/16 ips)
EP
Recording time (max.)
Dimensions
: 150 (W) x 42 (H) x
68 (D) mm
SP
EP
: 40 minutes
: 120 minutes
(with TC-40 cassette)
(5-15/16" x 1-11/16" x
2-11/16")
: Approx. 320 g (0.71 lbs)
Operating temperature : 0°C to +40°C
(32°F to 104°F)
Weight
Operating humidity
Storage temperature
: 35% to 80%
: –20°C to +50°C
(–4°F to 122°F)
CASSETTE ADAPTER (C-P7U)
Dimensions
: 188 (W) x 25 (H) x
104 (D) mm
Weight
GR-AX910
GR-AX810
: Approx. 760 g (1.7 lbs)
: Approx. 780 g (1.8 lbs)
(7-7/16" x 1" x 4-1/8")
: Approx. 240 g (0.53 lbs)
: “AA (R6)”-size battery x 1
Weight
Accessory
Dimensions
(Including viewfinder)
Provided Accessories ...................... ੬ pg. 6
GR-AX910
: 109 (W) x 113 (H) x 206
(D) mm (4-5/16" x 4-1/2"
x 8-1/8")
: 109 (W) x 113 (H) x 226
(D) mm (4-5/16" x 4-1/2"
x 8-15/16")
Optional Accessories
•Battery Packs BN-V12U, BN-V22U, BN-V25U
•Car Battery Charger BH-V3U
•Battery Charger BH-VC10U
•Car Battery Cord AP-V7U
GR-AX810
CAMERA
•RF Unit RF-V5U
•Compact VHS-C Cassettes TC-40/30/20
•Active Carrying Bag CB-V7U
Pick up
Lens
: 1/4" format CCD
: F1.2, f = 4.1 to 57.4 mm,
14:1 power zoom lens
with auto iris and macro
control, filter diameter
46 mm
* Some acccessories are not available in some
areas. Please consult your nearest JVC dealer for
details on accessories and their availability.
Viewfinder
: Electronic viewfinder
with
Specifications shown are for SP mode unless
otherwise indicated. E. & O. E. Design and
specifications subject to change without notice.
•0.5" black/white CRT
(GR-AX810)
•0.55" color LCD
(GR-AX910)
White balance
adjustment
: Auto/Manual adjustment
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑOL
56
Alimentación
Indicador CHG. (carga)
Marcas
Esta cámara de video posee un sistema de alimentación
de 3 vías que le permite seleccionar la fuente de
alimentación más apropiada.
Al
tomacorriente
de alterna
Indicador
POWER
NOTAS:
● Sin alimentación no hay ninguna función disponible.
● Utilice exclusivamente la alimentación indicada.
● No utilice la unidades de alimentación suministradas con otro
equipo.
Indicador
END
CARGA DEL PAQUETE DE PILAS
ALIMENTACION
Conecte el cordón de alimentación de CA del
cargador a un tomacorriente. Se encenderá la luz
delindicador de alimentación.
1
2
Interruptor REFRESH
Indicador REFRESH
COLOCACION DEL PAQUETE DE PILAS
Enganche.
Alinee las marcas y deslice el paquete de pilas en la
dirección de la flecha hasta que quede bloqueado
en su lugar.
Se enciende la luz indicadora CHG.
EXTRACCION DEL PAQUETE DE PILAS
Cuando la carga está completa, se encenderá el
indicador END. Deslice el paquete de pilas en el
sentido opuesto al de la flecha.
3
Empuje.
BATT. RELEASE
PAQUETE
CARGA
DESCARGA
DE PILAS
BN-V11U
BN-V12U
BN-V22U
BN-V25U
aprox. 1 h. 10 m.
aprox. 1 h. 10 m.
aprox. 2 h. 10 m.
aprox. 2 h. 40 m.
aprox. 3 h. 30 m.
aprox. 3 h. 30 m.
aprox. 7 h.
Marcador
de carga
aprox. 10 h.
USO DEL PAQUETE DE PILAS
COLOCACION DEL PAQUETE DE
PILAS
**INDICADOR DE CARGA
Enganche la parte superior del mismo en la cámara
de video y empuje el paquete de pilas hasta que se
bloquee en su lugar.
Se ha suministrado un indicador de carga
sobre el paquete de pilas para ayudarle a
recordar si ha sido cargado o no. Los dos
colores suministrados (rojo y negro), le
permiten seleccionar la carga y la descarga.
1
2
EXTRACCION DEL PAQUETE DE PILAS
Deslice BATT. RELEASE y extraiga el paquete de
pilas.
**REFRESCADO
El adaptador de CA se caracteriza por la
función REFRESH que le permite descargar
totalmente el paquete de pilas antes de
recargarlo.
TIEMPO DE GRABACION APROXIMADO
PAQUETE
GR-AX910
DE PILAS
GR-AX810
BN-V11U 1 h. (35 m.)
1 h. 5m. (35 m.)
Para descargar las pilas . . .
..... coloque el paquete de pilas en el adaptador
como se muestra en la ilustración de la
izquierda. Luego presione REFRESH. El
indicador REFRESH se enciende cuando se
inicia la descarga y se apaga cuando la descarga
ha terminado.
BN-V12U 1 h. (35 m.)
1 h. 5m. (35 m.)
BN-V22U 2 h. 10 m. (1 h. 20 m.)
BN-V25U 2 h. 50 m. (1 h. 50 m.)
2 h. 15 m. (1 h. 25 m.)
3 h. (1 h. 50 m.)
(
): cuando la luz de video está encendida.
Download from Www.Somanuals.com. All Manuals Search And Download.
GUIA PARA OPERACION RAPIDA
Si la unidad comienza a funcionar mal, deje de usarla inmediatamente y consulte a su concesionario local de JVC.
57
ALIMENTACION
INSERCION DEL CASSETTE
DE VIDEO
Enganche.
1
EJECT (eyección)
1
Empuje.
2
3
PUSH
2
(presione)
Inserte.
BATT. RELEASE (extracción de la batería)
Utilización de la batería
1 Enganche el extremo superior de la batería
en la cámara de video. (Procedimiento para
carga: ੬ P. 8)
1 Deslice EJECT.
2 Inserte un cassette de video.
3 Presione PUSH.
2 Empuje la batería hacia adentro hasta que
(Por más detalles, ੬ P. 13.)
quede bloqueada en su lugar.
Para extraer la batería
Deslice BATT. RELEASE y extraiga la batería.
REPRODUCCION
FILMACION
PLAY/PAUSE
3
(reproducción/pausa)
REW
2
(rebobinado)
1
Perilla de
abertura/cierre
LENS COVER
2
STOP
Colóquelo en “CAMERA”.
(parada)
3
Botón para inicio/parada de
grabación
1
Colóquelo en “PLAY”.
1 Deslice la perilla de abertura/cierre LENS
COVER para abrir la tapa del objetivo.
2 Adjuste el interruptor de alimentación en
“CAMERA”.
— El indicador de alimentación se
encenderá y aparecerá una imagen en el
visor.
1 Ajuste el interruptor de alimentación en
“PLAY”.
2 Presione REW.
— La cinta se detiene automáticamente al
comienzo de la misma.
3 Presione PLAY/PAUSE.
— Comienza la reproducción y la imagen
aparece en el visor.
•Presione STOP para detener la grabación.
(Por más detalles, ੬ P. 38.)
3 Presione el botón inicio/parada de
grabación.
— Comenzará la grabación.
•Para detener temporariamente la grabación,
presione nuevamente el botón de inicio/
parada de grabación.
Ⅲ O simplemente reproduzca la cinta en un
VCR de VHS utilizando el adaptador de
cassette (VHS Playpak). ੬ P. 36.
(Por más detalles, ੬ P. 16.)
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR SERVICING
58
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1-800-252-5722
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before
operating the unit. In the event that repair is necessary, or for the address nearest your location,
please refer to the factory service center list below or within the Continental United States, call 1-800-
252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF US JVC CORP.
FACTORY SERVICE CENTER LOCATIONS
107 Little Falls Road
Fairfield, NJ 07004-2105
(201) 808-9279
1500 Lakes Parkway
Lawrenceville, GA 30243-5357
(770) 339-2522
705 Enterprise Street
Aurora, IL 60504-8149
(708) 851-7855
5665 Corporate Avenue
Cypress, CA 90630-0024
(714) 229-8011
10700 Hammerly, Suite 110
Houston, TX 77043-2310
(713) 935-9331
2969 Mapunapuna Place
Honolulu, HI 96819-2040
(808) 833-5828
230 Eliot Street
Ashland, MA 01721-2377
(508) 881-5923
14505 Commerce Way
Miami Lakes, FL 33016-1512
(305) 362-6252
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(415) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the
engineering and production of the wide array of JVC products, service is the key to maintaining the
high level performance for which JVC is world famous. The JVC service and engineering organization
stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF US JVC CORP.
107 Little Falls Road
Fairfield, NJ 07004-2105
If you ship the product...
Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit,
a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you
received when you purchased your JVC unit. Print your home return address on the outside and the
inside of the carton. Send to the appropriate JVC Factory Service Center as listed above.
Don't service it yourself.
ACCESSORIES
To purchase accessories for your JVC product, you
may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free:
1-800-882-2345.
CAUTION
To prevent electrical shock, do not open the
cabinet. No user serviceable parts inside.
Refer servicing to qualified service personnel.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
59
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO
THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP
from the date of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS
LABOR
1
YR
90
DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF
COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized
service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All
products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for
Television sets having a screen size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC
authorized service center, please call toll free: (800) 252-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center,
the name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse,
faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility
authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if
the model or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of
purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);from the date
of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY
OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT
LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT,
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE
LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive
Elmwood Park, New Jersey 07407
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR
DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT
WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain
this information for future reference.
Model No.:
Serial No:
Purchase date:
Name of dealer:
Download from Www.Somanuals.com. All Manuals Search And Download.
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive, Elmwood Park, N.J. 07407
0P2ri9n6teTdOiVn*JaUpNa*n YP
U
COPYRIGHT© 1996 VICTOR COMPANY OF JAPAN, LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|