JVC CRT Television HV 28D40BK User Manual

HV-32D40BK  
HV-28D40BK  
INSTRUCTIONS  
Integrated Digital Colour Television  
Trade Mark of the DVB Digital Video Broadcasting  
Project (1991 to 1996) Number: 3081  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to move the TV  
When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful  
not to trap your hands when putting the TV down.  
1
2
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Thank you for buying this JVC colour television.  
To make sure you understand how to use your new TV, please read this manual thoroughly before you  
begin.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
CAUTION:  
• Operate only from the power source specified  
(AC 220 – 240 V, 50 Hz) on the unit.  
• Avoid damaging the AC plug and power cord.  
• When you are not using this unit for a long  
period of time, it is recommended that you  
disconnect the power cord from the main  
outlet.  
• The main power button on the TV does not  
fully isolate the TV from the mains supply. If  
you are not going to use this TV for a long  
period of time, be sure to disconnect the mains  
plug from the mains outlet.  
Avoid improper installation and never put the unit where good  
ventilation is not possible.  
When installing this TV, distance recommendations must be  
maintained between the set and the wall, as well as inside a tightly  
enclosed area or piece of furniture.  
Adhere to the minimum distance guidelines shown for safe operation.  
Failure to heed the following precautions may result in damage to the TV or  
remote control.  
DO NOT block the TV’s ventilation openings or holes.  
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be  
able to get out.)  
DO NOT place anything on top of the TV.  
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)  
DO NOT allow objects or liquid into the cabinet openings.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
DO NOT place any naked flame sources, such as lighted candles, on the TV.  
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.  
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.  
Never use any cleaner or detergent on it.  
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it  
yourself or remove the rear cover.  
D.I.S.T. demonstration  
To start the D.I.S.T. demonstration:  
Press the H button to display the menu bar. Then press the yellow button.  
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.  
To quit the D.I.S.T. demonstration:  
Press the yellow button, TV/DTV button, p p buttons or any of the number buttons.  
NOTE:  
Due to static electricity, the TV may be covered with dust.  
If this happens, wipe the TV with a soft cloth being careful not to scratch the TV.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digital terrestrial broadcasting (DVB-T) service area  
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial  
broadcasting, depending on the area in which you live, you may not be able to receive Digital  
terrestrial broadcasting (DVB-T).  
For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW  
website etc.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the aerial................................. 7  
Putting the batteries into the remote  
Remote control buttons and  
functions..............................................15  
Turn the TV on or off from standby mode ... 15  
PICTURE TILT......................................... 40  
DECODER (EXT-2).................................. 41  
ATTENUATOR......................................... 44  
Teletext function ....................................25  
Basic operation (Digital)........................... 25  
Basic operation (Analogue)...................... 26  
Using the List Mode ................................. 26  
Hold.......................................................... 27  
Sub-page ................................................. 27  
Reveal...................................................... 27  
Size.......................................................... 27  
Index ........................................................ 27  
Cancel...................................................... 27  
DTV menu............................................... 45  
Timers (DTV Timer Recording)................ 45  
Configuration............................................ 47  
Edit PR List .............................................. 49  
Installation................................................ 52  
Common Interface.................................... 52  
Additional preparation .......................... 53  
Connecting external equipment ............... 53  
Troubleshooting .................................... 56  
Specifications ........................................ 59  
Using the TV’s menu..............................28  
Basic operation ........................................ 28  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Caution  
• Turn off all the equipment including the TV before connecting anything.  
Connecting the aerial  
• The connecting cables are not provided.  
• For further details, refer to the manuals provided with the devices to be connected.  
If you connect via a device with an  
For example  
antenna terminal such as a VCR,  
follow A B C in the diagram  
opposite.  
Aerial  
Back of the TV  
75-ohm  
Coaxial  
If you connect the antenna  
Cable  
directly to the TV, follow 1.  
To use the T-V LINK functions, you must  
have a T-V LINK compatible VCR  
EXT-  
4
connected by a SCART cable C to the EXT-  
LINK functions, see “T-V LINK functions”  
on page 11.  
EXT-1  
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
• To connect more equipment, please see  
“Connecting external equipment” on  
page 53.  
• To connect additional audio equipment,  
see “Connecting speakers/amplifier” on  
page 55.  
21-pin  
SCART  
Cable  
75-ohm  
Coaxial  
Cable  
• If you connect a decoder to a T-V LINK  
compatible VCR, set the DECODER  
(EXT-2) function to ON. For details, see  
“DECODER (EXT-2)” on page 41.  
Otherwise, you will not be able to watch  
scrambled channels.  
To Aerial  
Input  
VCR  
• When receiving Digital terrestrial  
broadcasting (DVB-T), reception can  
suddenly be lost if the signal becomes  
weak. Use a correctly installed high-  
performance antenna.  
To Aerial  
Output  
AV IN/OUT  
Terminal  
• When connecting via a device with an  
antenna terminal such as a VCR, depending  
on the connection method, the signal may  
be weakened. If this happens, use a booster  
to increase the signal strength.  
• In areas with a lot of radio communication  
such as near ports or airports, noise may  
be introduced into the picture or sound. In  
such cases, reception may be improved by  
using a high-performance antenna.  
• Read the instruction manual of the  
devices which you connect to the TV.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Setting up your TV  
Rear Panel  
Putting the batteries into the  
remote control  
Use two AA/R6 dry cell batteries.  
Insert the batteries from the - end, making  
sure the + and - polarities are correct.  
Not use  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
• Follow the warnings printed on the  
batteries.  
R
• Battery life is about six months to one  
year, depending on how much you use the  
remote control.  
• The batteries we supply are only for  
setting up and testing your TV, please  
replace them as soon as you need to.  
• If the remote control does not work  
properly, replace the batteries.  
1 Aerial socket (page 7)  
2 EXT-1 terminal (pages 7, 42, 53)  
3 EXT-2 terminal (pages 7, 11, 42, 53)  
4 EXT-3 terminal (pages 42, 53)  
5 EXT-4 terminal (pages 42, 53)  
6 AUDIO OUT terminal (page 55)  
7 Common Interface terminal (page 52)  
Initial settings  
When the TV is first turned on, it goes into  
the initial settings mode, and you will see the  
JVC logo. Follow the instructions on the  
screen display to make the initial settings.  
Connecting the power cord to  
the AC outlet  
Caution  
• Operate only from the power source specified  
(AC 220 – 240 V, 50 Hz) on the unit.  
TV/DTV  
7
buttons  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Setting up your TV  
When the Automatic Search has  
finished, the EDIT PR LIST menu  
appears  
1 Press the main power button on the  
TV  
The power lamp lights green and the JVC  
logo appears.  
EDIT PR LIST  
1
BBC ONE  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
Select function  
Select PR OK Watch PR  
Main power  
button  
Power lamp  
D0202-EN  
• If you want to, you can now edit the  
programme numbers (PR) using the  
EDIT PR LIST function. For details,  
see “Edit PR List” on page 49.  
• If the JVC logo does not appear this is  
because your TV has already been  
turned on for the first time:  
Perform the initial settings with  
“Installation” (see page 52) in the  
DTV menu and “AUTO PROGRAM  
(Analogue)” (see page 36) in the SET  
UP menu.  
• To receive SKY 1 you need a satellite  
tuner. You must have the satellite tuner  
set to SKY 1 before starting the AUTO  
PROGRAM function which follows.  
• If you do not want to edit programme  
numbers (PR), go to the next step.  
3 Press the H button  
The EDIT PR LIST menu disappears and  
the Analogue terrestrial broadcasting  
AUTO PROGRAM starts.  
The AUTO PROGRAM menu appears  
and received TV channels are  
automatically stored in the programme  
numbers (PR).  
2 Press the a button  
The Digital terrestrial broadcasting  
(DVB-T) Automatic Search starts.  
The Digital terrestrial broadcasting  
(DVB-T) channels which can be received  
are automatically registered.  
>> AUTO PROGRAM  
CH 28  
14%  
OK  
Installation > Automatic Search  
D0004-EN  
Channels:  
BBC ONE  
BBC TWO  
BBC THREE  
BBC NEWS 24  
BBCi  
• To cancel the AUTO PROGRAM  
function:  
Press the TV/DTV button.  
CBBC Channel  
UHF  
CH:68  
100%  
MENU  
Cancel, go to Installation  
Cancel, go to DTV  
BACK  
D0201-EN  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Setting up your TV  
After the AUTO PROGRAM has  
Now, the initial settings are complete,  
and you can watch the TV  
finished, the EDIT menu appears  
and Channel 5 are automatically set to the  
TV doesn’t receive one of these TV  
channels, that programme number (PR)  
will not be set. Programme number PR6 is  
not normally set.  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
ID  
MANUAL  
OK  
MOVE  
• If a TV channel you want to view is not  
set to a programme number (PR), you can  
set it manually. To set an Analogue  
terrestrial broadcasting channel, see  
“EDIT/MANUAL (Analogue)” on  
page 36. To set a Digital terrestrial  
broadcasting (DVB-T) channel, see  
“Manual Search:” on page 52.  
• The AUTO PROGRAM function does not  
set the programme number PR 0 (AV) for  
your video cassette recorder. You will  
need to set this using the MANUAL  
function.  
INSERT DELETE  
D0038-EK  
• If you want to, you can now edit the  
programme numbers (PR) using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL (Analogue)” on  
page 36.  
• If you do not want to edit programme  
numbers (PR), go to the next step.  
4 Press the a button to display the  
T-V LINK menu  
T-V LINK  
• In some areas you may get TV reception  
from more than one transmitter, for  
example different ITV regions. In this  
case each TV channel could be set twice.  
If this happens, the first set of channels  
will have the stronger signal. If you want  
to delete the second set of channels, you  
will have to do it manually (see page 36).  
DOWNLOAD TV  
RECORDING DEVICE  
OK  
EXIT  
D0005-EN  
If you do not have a T-V LINK  
compatible VCR connected:  
Press the TV/DTV button to exit the T-V  
LINK menu.  
For users in the UK:  
If you have any problems setting up your  
new TV, please call the  
Helpline on 0870 330 5000.  
The T-V LINK menu disappears.  
If you have a T-V LINK compatible  
VCR connected to the EXT-2  
terminal:  
Follow the operating procedure  
“Downloading the data to VCR” on  
page 11 to transmit the Programme  
number (PR) data.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Downloading the data to VCR  
You can transmit to the latest Analogue  
terrestrial broadcasting Programme numbers  
(PR) data to a VCR with the T-V LINK  
function.  
T-V LINK functions  
When you have a T-V LINK compatible  
VCR connected to the EXT-2 Terminal on  
the TV, it is easier to set up the VCR and to  
view videos. T-V LINK uses the following  
features:  
Caution  
• This only works when a T-V LINK  
compatible VCR is connected to the  
EXT-2 terminal.  
• This only works when the T-V LINK  
menu is being displayed.  
To use T-V LINK functions:  
A “T-V LINK compatible VCR” means a  
JVC video cassette recorder with the T-V  
LINK logo, or with one of the following  
logos. However, these VCRs may support  
some or all of the features described earlier.  
For details, see your VCR instruction  
manual.  
T-V LINK  
DOWNLOAD TV  
RECORDING DEVICE  
“Q-LINK” (a trademark of Panasonic  
Corporation)  
OK  
EXIT  
“Data Logic” (a trademark of Metz  
Corporation)  
“Easy Link” (a trademark of Phillips  
Corporation)  
D0005-EN  
1 Turn on the VCR  
2 Press the a button  
“Megalogic” (a trademark of Grundig  
Corporation)  
“SMARTLINK” (a trademark of Sony  
The data transmission begins.  
T-V LINK TV  
RECORDING DEVICE  
Corporation).  
TRANSFER. . . . .  
D0037-EN  
Pre-set download  
The T-V LINK menu disappears once the  
data transmission ends.  
The VCR will automatically download the  
registered data on the TV Analogue  
terrestrial broadcasting channels from the  
TV. This means you do not need to set up the  
program channels on your VCR manually.  
The preset download function automatically  
begins when the initial setting is complete or  
whenever you carry out the AUTO  
When the T-V LINK menu is  
changed over to another menu:  
The TV has finished its menu. This new  
menu is operated from the VCR. See the  
VCR instruction manual for what to do  
next.  
PROGRAM or EDIT/MANUAL functions.  
If “FEATURE NOT AVAILABLE”  
appears at the T-V LINK menu:  
Check the following three items. Then  
press the 2 button to retry data  
transmission.  
• Has a T-V LINK compatible VCR  
been connected to the EXT-2  
terminal?  
• Has the VCR power been turned on?  
• Does the SCART cable that is  
connected to the EXT-2 terminal to T-  
V LINK compatible VCR have all its  
proper connections?  
You can also carry out this function using  
your VCR controls.  
When “FEATURE NOT AVAILABLE” is  
displayed:  
If “FEATURE NOT AVAILABLE” is  
displayed, the download was not performed  
correctly. Before trying to download again,  
check that:  
• the VCR power is turned on  
• the VCR is T-V LINK compatible  
• the VCR is connected to the EXT-2  
terminal  
• the SCART cable is fully wired.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Setting up your TV  
When the VCR is not ready, the following  
messages are displayed.  
Direct Rec  
“What You See Is What You Record”  
You can easily record to VCR the images  
that you are watching on the TV.  
ERROR  
MESSAGE  
Cause and  
countermeasure  
For details, read the manual for your VCR.  
Use your VCR controls. “DEVICE IS  
RECORDING” is displayed.  
NO  
The VCR is not able to  
RECORDING record.  
Check the VCR.  
NO  
The TV input is set to EXT-4.  
You cannot carry out Direct Rec using your  
TV’s control.  
RECORDING Since the EXT-4 picture  
POSSIBLE  
cannot be output to EXT-2,  
DIRECT REC is not possible.  
Generally, the VCR cannot record a TV  
channel that it cannot receive properly on its  
own tuner, even if you can view that TV  
channel on the TV. However, some VCRs  
can record a TV channel by using the TV’s  
output if that channel can be viewed on the  
TV. For details, see your VCR instruction  
manual.  
NO  
The RECORDING DEVICE  
RECORDING, is not ready to record. Check  
MEDIA  
PROBLEM  
the VCR tape.  
NO  
The RECORDING DEVICE  
RECORDING, cannot record as it is  
DEVICE BUSY recording or playing. Check  
the VCR.  
Do not turn the TV off in the following  
cases.  
• when recording images from an external  
device connected to the TV (for example  
a camcorder)  
Refer to the VCR instruction manual.  
• when recording a TV channel after it has  
been unscrambled on a decoder  
• when recording a TV channel by using the  
TV’s output because the VCR’s own  
tuner cannot properly receive that  
channel.  
• when recording Digital terrestrial  
broadcasting (DVB-T).  
If you change channels or perform  
other operations while a Digital  
terrestrial broadcasting (DVB-T)  
channel is being recorded, a window  
appears asking whether to stop the  
recording.  
Press the a button to stop the  
recording, or the TV/DTV button to  
continue the recording.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TV buttons and functions  
Turn the main power on  
Press the main power button on the  
TV.  
The power lamp lights red and your TV is in  
standby mode.  
• If the power lamp lights green, the TV is  
already on.  
To turn the main power off:  
Press the main power button again.  
The power lamp goes off.  
Caution  
• The main power button on the TV does  
not fully isolate the TV from the AC  
supply. If you are not going to use the TV  
for a long period, be sure to disconnect  
the AC plug from the AC socket.  
Turn the TV on from standby  
mode  
Press the P p buttons to turn the TV  
on from standby mode  
Choose a TV channel  
S
R
L/MONO  
EXT-5  
P
Press the P p buttons to choose a  
programme number (PR) or an EXT  
terminal  
The EXT terminal cannot be chosen when  
watching Digital terrestrial broadcasting  
(DVB-T).  
S
R
L/MONO  
EXT-5  
P
To switch between Analogue  
terrestrial broadcasting and Digiatl  
terrestrial broadcasting (DVB-T):  
1 Press the r (Volume) button  
2 Press the r (Volume) button  
again when the volume level  
indicator appears  
See the pages in parentheses for details.  
1 Main power button (pages 9, 13)  
2 Power lamp (pages 9, 13)  
3 Remote control sensor  
4 r (Volume) button (page 14)  
5 P p buttons/ q buttons (page 13)  
6 Headphone jack (mini jack) (page 53)  
7 EXT-5 terminal (pages 42, 53)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
TV buttons and functions  
Adjust the volume  
1 Press the r (Volume) button once  
The volume level indicator appears.  
2 Press the q buttons while the  
volume level indicator is displayed  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
1 Muting button  
2 Number buttons  
3 Information button  
4 Colour button  
1
2
~
!
5 TV/DTV button  
6 7 buttons  
7 g (Text) button  
8 p p buttons  
9 VCR/DVD/Teletext control buttons  
0 p buttons  
- c button  
= 3 button  
~ # (Standby) button  
! VCR/TV/DVD switch  
@ G button  
# H button  
$ a button  
3
4
5
@
#
$
% b button  
^ r (Volume) q buttons  
& GUIDE button  
* SUBTITLE button  
( X (Multi) button  
) f/g (Freeze/Swap) button  
6
7
%
^
Turn the TV on or off from  
standby mode  
8
Press the # (standby) button to turn  
the TV on or off.  
When the TV is turned on, the power lamp  
&
*
9
0
lights green.  
• The power can be turned on by pressing  
the TV/DTV button, p p buttons or  
Number buttons.  
(
)
-
=
To turn the TV on or off, set the VCR/TV/  
DVD switch on the remote control to the  
TV position and press the # button.  
If the VCR/TV/DVD switch on the remote  
control is set to a position other than TV,  
the TV will not be turned on or off even if  
the # button is pressed.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Remote control buttons and functions  
• You can choose a video input signal  
from the S-VIDEO signal (Y/C signal)  
and regular video signal (composite  
signal). For details, see “S-IN (S-  
VIDEO input)” on page 42.  
Choose a TV channel and  
watch images from external  
devices  
• If you do not have a clear picture or no  
colour appears, change the colour  
system manually. See “COLOUR  
SYSTEM” on page 31.  
• If you choose an EXT terminal with no  
input signal, the EXT terminal number  
becomes fixed on the screen.  
• If the picture is tilted, correct it. See  
“PICTURE TILT” on page 40.  
Switching between Digital  
terrestrial broadcasting (DVB-T)  
and Analogue terrestrial  
broadcasting.  
• This TV set has a function which can  
automatically change over the input  
according to a special signal output  
from an external device. (The EXT-4  
and EXT-5 terminals do not support  
this function.)  
• Since this TV is designed to make full  
use of the resolution of the original  
video source, the motion may appear  
unnatural when the video source is  
input with 625p progressive-scanning  
component signals.  
If this happens, change the output  
setting of the connected device to 625i  
interlace-scanning component signal  
output. See the instructions that came  
with the device for more information.  
Press the TV/DTV button.  
The broadcasting is switched every time the  
button is pressed.  
Use the number buttons:  
Enter the programme number (PR)  
of the channel using the number  
buttons.  
Example:  
• PR 6 press 6  
• PR 12 press 1 and 2  
• PR 123 press 1, 2 and 3  
Use the p p buttons:  
Press the p p buttons to  
choose the programme number  
(PR) you want.  
To return to a TV channel:  
Press the TV/DTV button, the p p buttons  
or the number buttons.  
• For Digital terrestrial broadcasting (DVB-  
T), if the FAVOURITE setting in the  
“Edit PR List” (see page 49) has been set,  
only that programme number (PR) can be  
chosen.  
• For Analogue terrestrial broadcasting, an  
EXT terminal can also be chosen.  
Use the AV button:  
Press the AV button to choose an  
EXT terminal.  
TV mode  
EXT modes  
Analogue  
terrestrial  
broadcasting  
EXT-2  
EXT-1  
or  
EXT-3  
or  
S3  
E3  
Digital  
terrestrial  
broadcasting  
(DVB-T)  
EXT-5  
EXT-4  
or  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
To use the programme number PR 0  
(AV):  
Information function  
When the TV and VCR are connected only  
by the aerial cable, choosing the programme  
number PR 0 (AV) allows you to view  
images from the VCR. Set the VCR RF  
channel to the programme number PR 0  
(AV) manually. For details, see “EDIT/  
MANUAL (Analogue)” on page 36.  
Pressing the G button changes the choice as  
follows:  
When watching Digital terrestrial  
broadcasting (DVB-T):  
When the h (Information) button is pressed,  
the programme information appears for  
approximately 1 minute.  
ITV News  
CH61  
41  
Now: 13:00-14:00 Steve Scott  
Next: 14:00-14:30 Steve Scott  
13:19  
D0203-EN  
TV mode  
EXT modes  
• When the h (Information) button is  
pressed while the information is being  
displayed, the information disappears.  
Analogue  
terrestrial  
broadcasting  
EXT-2  
PR 0  
EXT-1  
or  
EXT-3  
• The time display in the programme  
information uses the time information  
which is included in the Digital terrestrial  
broadcasting (DVB-T). Depending on the  
channel, the time information may not be  
correct.  
or  
S3  
E3  
Digital terrestrial  
broadcasting  
(DVB-T)  
EXT-5  
EXT-4  
or  
• The VCR sends its playback image along  
the aerial cable as an RF (radio frequency)  
signal.  
When watching Analogue terrestrial  
broadcasting:  
You can see the channel number of the  
programme you are watching, the current  
time or the PR LIST.  
• Also see your VCR instruction manual.  
From the PR LIST, you can choose a channel  
or EXT terminal.  
Adjust the volume  
Press the r q buttons to adjust  
the volume.  
The volume indicator appears and the  
volume changes as you press the r q  
buttons.  
Press the  
display the information you want to  
see.  
Pressing the  
the display as follows:  
(Information) button to  
h
(Information) button changes  
h
Muting the sound  
PR LIST  
Press the (muting) button to  
l
PR  
ID  
Channel number display  
12 : 00  
turn off the sound.  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
BBC1  
Pressing the (muting) button again  
l
restores the previous volume level.  
No indication  
OK  
-10  
+10  
D0011-EN  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Remote control buttons and functions  
Channel number display:  
ZOOM function  
The channel number and channel name  
(when the channel name is registered) of the  
programme you are watching or the EXT  
terminal number is displayed.  
You can change the screen size according to  
the picture aspect ratio. Choose the optimum  
one from the following ZOOM modes.  
Time display:  
The current time of the teletext data is  
AUTO:  
When a WSS (Wide Screen Signalling)  
signal, which shows the aspect ratio of the  
picture, is included in the broadcast signal or  
the signal from an external device, the TV  
automatically changes the ZOOM mode to  
16:9 ZOOM mode or FULL mode according  
to the WSS signal.  
If a WSS signal is not included, the picture is  
displayed according to the ZOOM mode set  
with the 4:3 AUTO ASPECT function.  
• For details of the 4:3 AUTO ASPECT  
function, see “4:3 AUTO ASPECT” on  
page 32.  
• When the AUTO (WSS) mode does not  
function correctly due to poor WSS signal  
quality or when you want to change the  
ZOOM mode, press the c button  
and change to another ZOOM mode.  
• When watching a 16:9 FULL programme  
with Digital terrestrial broadcasting  
(DVB-T), the aspect ratio is FULL.  
displayed.  
If the TV has not received a TV channel that  
has teletext programmes since it was turned  
on, the time display is blank. To view the  
current time, choose a TV channel that has  
teletext programmes.  
• An incorrect current time is sometimes  
displayed when watching videos.  
PR LIST:  
The programme number (PR) and EXT  
terminal list is displayed.  
Pressing the a button after choosing the  
programme number (PR) or EXT terminal  
with the 7 buttons will display the  
chosen programme or EXT terminal.  
• For programme numbers (PR) for which  
the CHILD LOCK function is set, the n  
(CHILD LOCK) mark is displayed. For  
details see “CHILD LOCK” on page 34.  
REGULAR:  
Use to view a normal picture (4:3 aspect  
ratio) as this is its original shape.  
PANORAMIC:  
This stretches the left and right sides of a  
normal picture (4:3 aspect ratio) to fill the  
screen, without making the picture appear  
unnatural.  
• The top and bottom of the picture are  
slightly cut off.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
14:9 ZOOM:  
Choose the ZOOM mode  
This zooms up the wide picture (14:9 aspect  
ratio) to the upper and lower limits of the  
screen.  
1 Press the c button to display  
the ZOOM menu  
ZOOM  
AUTO  
REGULAR  
PANORAMIC  
14:9 ZOOM  
16:9 ZOOM  
16:9 ZOOM SUBTITLE  
FULL  
16:9 ZOOM:  
This zooms up the wide picture (16:9 aspect  
ratio) to the full screen.  
OK  
D0009-EN  
2 Press the 6 buttons to choose a  
ZOOM mode. Then press the a  
button  
16:9 ZOOM SUBTITLE:  
This zooms up the wide picture (16:9 aspect  
ratio) with subtitles to the full screen.  
The picture expands and the chosen  
ZOOM mode is displayed in about 5  
seconds.  
• The ZOOM mode may be  
automatically changed by the control  
signal from an external device. When  
you want to return to the previous  
ZOOM mode, choose the ZOOM  
mode again.  
FULL:  
This uniformly stretches the left and right  
sides of a normal picture (4:3 aspect ratio) to  
fill the wide TV screen.  
Adjusting the visible area of the  
picture  
• For 16:9 aspect ratio pictures that have  
been squeezed into a normal picture (4:3  
aspect ratio), use the FULL mode to  
restore the picture to its original shape.  
If subtitles or the top (or bottom) of the  
picture are cut off, you can adjust the visible  
area of the picture manually.  
1 Press the c button  
• When you use this TV’s output signal to  
record a Digital terrestrial broadcasting  
(DVB-T) 16:9 broadcast, it will be  
recorded with its picture squeezed into a  
4:3 aspect ratio picture.  
Use the FULL mode to restore the picture  
to its original shape when playing the  
recording.  
The ZOOM menu appears.  
2 Press the a button to display the  
ZOOM mode indicator  
The indicator appears.  
16 : 9 ZOOM  
D0010-EN  
3 While it is displayed, press the 6  
buttons to change the position of  
the picture  
• You cannot adjust the visible area in  
REGULAR or FULL mode.  
• Some menu displays can be cut off when  
you move the visible area up or down  
while watching Digital terrestrial  
broadcasting (DVB-T).  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
3D CINEMA SOUND function  
Using the MULTI-PICTURE  
function  
You can enjoy sounds with a wider  
ambience.  
• This function does not work for the sound  
from headphones.  
When watching Digital terrestrial  
broadcasting (DVB-T):  
1 Press the X button  
Press the 3 button and choose  
“ON”, “MONO” or “OFF”.  
ON:  
1
2
12  
Choose to add the 3D CINEMA SOUND  
effect to stereo sound.  
D0101-EN  
MONO:  
2 Press the 5 buttons and choose  
2, then press the a button  
Choose to add the 3D CINEMA SOUND  
effect to mono sound.  
OFF:  
Choose to return to one screen.  
1
Choose to cancel the 3D CINEMA SOUND  
effect.  
D0102  
• The 3D CINEMA SOUND effect can be  
adjusted with the “3D CINEMA  
SOUND” menu (see page 33).  
Choose to change to 2-pictures multi.  
2
D0103  
2-pictures multi:  
Using the FREEZE function  
This function can only be used when  
watching Analogue terrestrial  
broadcasting.  
Main-  
picture  
Sub-  
picture  
D1056-EN  
You can view the current programme as a  
still picture.  
This cannot be chosen when watching  
Digital terrestrial broadcasting (DVB-T).  
12  
D0104  
1 Press the f button  
The still picture of the current picture will  
appear.  
• You can watch Digital terrestrial  
broadcasting (DVB-T) in the main-  
picture. You can watch the Analogue  
terrestrial broadcasting or EXT picture  
in the sub-picture.  
current  
still picture  
programme  
• When the Digital terrestrial  
broadcasting (DVB-T) in the main-  
picture is 16:9 FULL, the main-picture  
aspect ratio is 16:9.  
• The main-picture sound is emitted  
from the TV speaker. If headphones  
are connected, you can listen to the  
sub-picture sound. Adjust the  
headphone volume with  
HEADPHONE VOLUME in the  
SOUND menu. The main-picture  
sound cannot be listened to with the  
headphones.  
D1056-EN  
To cancel the FREEZE function:  
Press the f button, the p p buttons or  
the number buttons.  
• The FREEZE function does not work  
while a sub-picture is displayed.  
• The still picture cannot be output from  
the TV.  
• The FREEZE function does not work  
for pictures of 1125i signal.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Remote control buttons and functions  
• Choose the main-picture channel by  
pressing the p p buttons. Choose  
the sub-picture channel by pressing the  
p buttons.  
12-pictures multi:  
Still  
pictures  
• You cannot use the g (swap) button.  
When watching Digital terrestrial  
broadcasting (DVB-T), the main-  
picture and sub-picture cannot be  
switched.  
Moving  
picture  
D0058-EN  
• When set to 2-pictures multi, you can  
view a TV picture and a picture from  
an external device. You can not view a  
TV picture on more than one screen at  
the same time.  
• 1125i, 625p, and 525p signal pictures  
cannot be displayed as the sub-picture.  
To return the multi-picture to one  
screen:  
Press the X button, press the 5  
buttons to choose one screen, and then  
press the a button.  
• When 12-pictures multi is set, pictures  
from external devices are not  
displayed.  
• When set to 2-pictures multi, the main-  
picture can be changed by pressing the  
p p buttons. The sub-picture screen  
can be changed by pressing the p  
buttons.  
• Pressing the TV/DTV button will also  
return the display to one screen.  
When watching Analogue terrestrial  
broadcasting:  
When set to 12-pictures multi and  
there are more than 12 pictures, the  
next or previous 12 screens can be  
displayed by pressing the p buttons.  
1 Press the X button  
The MULTI-PICTURE menu appears.  
1
2
12  
D0101-EN  
2 Press the 5 buttons to choose  
the number of screens and then  
press the a button  
Changing the sub-picture  
Displaying the next or  
previous 12 screens  
Choose to return to one screen.  
1
• When set to 2-pictures multi, press the  
g (swap) button to switch the main-  
picture and sub-picture.  
D0102  
Choose to change to 2-pictures multi.  
2
2-pictures multi function does not  
work for a picture of 1125i signal.  
D0103  
• A picture of 625p or 525p signal  
cannot be displayed as the sub-picture.  
Pay attention to the following.  
Choose to change to 12-pictures multi.  
12  
D0104  
- When the EXT-4 picture is a picture  
of 625p or 525p signal, you cannot  
choose EXT-4 with the p buttons.  
- When the EXT-4 picture signal is  
changed to 625p, 525p or 1125i  
2-pictures multi:  
Main-  
picture  
Sub-  
picture  
signal while the EXT-4 picture is  
displayed as the sub-picture, the 2-  
pictures multi function is cancelled.  
D1056-EN  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
- The pictures cannot be swapped  
when a picture of 625p or 525p  
signal from EXT-4 is being  
Using the GUIDE  
• Use when watching Digital  
terrestrial broadcasting (DVB-T).  
displayed as the main picture.  
• Do not press the g (swap) button  
while you are recording the TV output  
on the VCR. If you do, the TV output  
signal will change.  
The guide appears when the GUIDE button  
is pressed while watching Digital terrestrial  
broadcasting (DVB-T).  
• You cannot view a scrambled channel  
in the sub-picture. If the g (swap)  
button is pressed when viewing a  
scrambled channel in the main-picture  
you have been viewing in the sub-  
picture will appear in both the main-  
picture and sub-picture.  
Electronic Programme Guide  
1
BBC ONE  
13:12  
The Rugby World Cu... 07:45-15:10  
Fiji v USA, Italy v Tonga & Samoa v  
Uruguay  
Channels  
Current Event  
Next Event  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
The Rugby Worid Cup... Movies Now  
• When set to 2-pictures multi and the  
headphones are connected, the sound  
for the main-picture is output from the  
TV speakers and the sound from the  
sub-picture is output from the  
30. CBBC Channel  
40. BBC NEWS 24  
Select PR OK Watch PR  
Next Event  
More..  
D0204-EN  
headphones.  
1 Quarter-screen  
- Adjust the volume of the sub-picture  
sound from the headphones with  
“HEADPHONE VOLUME” in the  
“SOUND” menu (see page 33).  
- The main-picture sound can not be  
heard through the headphones.  
• When set to 12-pictures multi, press  
the 7 buttons to choose the  
screen you want to view and the press  
the a button to display that picture  
on the whole screen.  
• The BLUE BACK function does not  
work when the MULTI-PICTURE  
function is being used.  
• The ZOOM function does not work  
when the MULTI-PICTURE function  
is being used.  
The programme you are watching is  
shown.  
• Sometimes you may notice a drop in  
picture quality while watching your  
programme in the quarter-screen. This  
is not a fault.  
2 Programme name, broadcast time  
and brief description of programme  
The programme name, broadcast time and  
a brief description of the programme are  
displayed for the programme chosen from  
the current event column or next event  
column.  
3 Channel column  
4 Current event column  
5 Next event column  
To return the multi-picture to one  
screen:  
Press the X button, press the 5  
buttons to choose one screen, and then  
press the a button.  
• Pressing the TV/DTV button will also  
return the display to one screen.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
Pressing the h (Information) button to  
display the help screen. Press it again to  
return to the guide screen.  
3 Press the a button  
The scheduled icon appears at the right of  
the chosen programme and the scheduling  
is completed.  
Electronic Programme Guide  
1
BBC ONE  
13:12  
The Rugby World Cu... 07:45-15:10  
Scheduled icon  
Fiji v USA, Italy v Tonga & Samoa v  
Uruguay  
Channels  
Current Event  
Next Event  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
The Rugby Worid Cup... Movies Now  
Red: Page up  
30. CBBC Channel  
40. BBC NEWS 24  
Green: Page down  
TV/DTV: Go to DTV  
Guide: Leave guide  
Back: Go to previous  
MENU  
OK  
Select PR OK Set reminder On/Off  
Current Event  
More..  
i: Exit help  
Next Event More..  
D0206-EN  
Select PR OK Watch PR  
D0205-EN  
• Steps 1 to 3 can be repeated to schedule  
more programmes.  
Help screen  
• When the GUIDE, TV/DTV, H or  
b buttons are pressed, the guide  
screen disappears and the normal screen  
returns.  
Choosing a channel  
1 Press the 6 buttons and choose  
a channel  
The programme name, broadcast time and  
a brief description of the programme are  
displayed.  
• Press the red and green buttons to  
scroll the channel column.  
When the TV is being watched, it  
automatically changes to the channel of the  
scheduled programme when the start time of  
the scheduled program is reached.  
• The scheduling function does not work  
when the TV is turned off.  
2 Press the a button  
The chosen programme appears on the  
quarter-screen.  
Cancelling a scheduled programme.  
Display the guide screen, choose a  
programme which has the scheduled icon  
(
), and press the a button.  
• When the GUIDE, TV/DTV, H or  
b buttons are pressed, the guide  
screen disappears and the normal screen  
returns.  
The icon disappears and the scheduling is  
cancelled.  
Checking programme details  
Press the 7 buttons and  
choose a programme from the  
Current Event or Next Event columns  
The programme name, broadcast time and a  
brief description of the chosen programme  
appear.  
Set reminder  
When you schedule a programme, you will  
not miss a programme that you want to  
watch.  
1 Press the 5 buttons and choose  
the Next Event column  
• Press the red and green buttons to scroll  
the channel column.  
2 Press the 6 buttons and choose  
the program that you want to  
schedule  
• When the GUIDE, TV/DTV, H or  
b buttons are pressed, the guide  
screen disappears and the normal screen  
returns.  
The programme name, broadcast time and  
a brief description of the chosen  
programme are displayed.  
• Press the red and green buttons to  
scroll the channel column.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
Displaying the Subtitles  
Operating a JVC brand VCR or  
DVD player  
• Use this function when watching  
Digital terrestrial broadcasting  
(DVB-T).  
These buttons will operate a JVC brand VCR  
or DVD player. Pressing a button that looks  
the same as the device’s original remote  
control button has the same effect as the  
original remote control.  
With Digital terrestrial broadcasting (DVB-  
T), some programmes are broadcast with  
subtitles. Subtitles can be displayed when  
watching these programmes.  
1 Set the VCR/TV/DVD Switch to the  
VCR or DVD position  
Press the SUBTITLE button when  
watching Digital terrestrial  
VCR:  
broadcasting (DVB-T)  
When you are operating the VCR, set the  
switch to the VCR position.  
• You can turn the VCR on or off with  
the # (standby) button.  
“Subtitle ON” appears at the top-left of the  
screen and, when the programme has  
subtitles, the subtitles are displayed.  
DVD:  
Subtitle ON  
D0207-EN  
When you are operating the DVD player,  
set the switch to the DVD position.  
• You can turn the DVD player on or off  
with the # (standby) button.  
• You can also press the H or  
T button and display the  
DVD disc menu screen, and then  
operate by pressing the 7  
buttons.  
• When the SUBTITLE button is pressed  
again, “Subtitle OFF” appears and the  
subtitles disappear.  
2 Press the VCR/DVD Control Button  
to control your VCR or DVD player  
• If your device is not made by JVC,  
these buttons will not work.  
• Even if your device is made by JVC,  
some of these buttons may not work,  
depending on the device you are using.  
• You can use the p buttons to choose  
a TV channel the VCR will receive, or  
choose the chapter the DVD player  
plays back.  
• Some models of DVD player use the  
p buttons for both operating the fast  
forward/backward functions and for  
choosing the chapter. In this case, the  
253 buttons do not work.  
You cannot turn the TV on or off when the  
VCR/TV/DVD switch is set to the VCR or  
DVD position.  
When you turn the TV on or off, set the  
VCR/TV/DVD switch to the TV position.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Teletext function  
1 Press the g button  
The digital teletext information appears.  
BBC ONE  
Powers  
For a full list of sections,  
press SELECT  
VCR/TV/  
DVD switch  
Contact info  
CBeebies Home  
Music  
Number  
buttons  
Taking Care  
NEWS  
SPORT  
WEATHER  
MAIN MENU  
Press TEXT to exit  
B
B
C
Colour  
buttons  
D0208-EN  
2 Operate it with the colour buttons,  
7 buttons and a button  
The operation method may differ depending  
on the contents of the digital teletext.  
Operate in accordance with the instructions  
displayed on digital teletext screen.  
• When “Press SELECT” or similar  
message appears on the screen, press  
the a button.  
7
buttons  
• When the g (Text) button is pressed, the  
TV returns to television broadcasting.  
• With Digital terrestrial broadcasting  
(DVB-T), in addition to digital teletext  
broadcasting at the same time as normal  
broadcasting, there are also channels with  
just digital teletext broadcasting.  
• The aspect ratio when watching a channel  
with just digital teletext broadcasting is  
the same as the aspect ratio of the picture  
watched previously.  
Basic operation (Digital)  
• When you press the g (Text) button  
while subtitles are on, the subtitles are  
turned off. When you press the g (Text)  
button again, the digital teletext screen is  
displayed.  
When watching Digital terrestrial  
broadcasting (DVB-T):  
With Digital terrestrial broadcasting (DVB-  
T), in addition to pictures and sound, you can  
also watch digital teletext.  
Digital teletext is sometimes broadcast at the  
same time as normal broadcasting.  
The functions described on pages  
26 and 27 cannot be used with  
digital teletext.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Teletext function  
When watching Analogue terrestrial  
broadcasting:  
Using the List Mode  
You can store the numbers of your favourite  
teletext pages in memory and call them up  
quickly using the colour buttons.  
Basic operation (Analogue)  
You can view two types of teletext  
broadcasts on the TV:  
FLOF (Fastext) and WST.  
To store the page numbers:  
1 Press B button to go into the  
List mode  
1 Choose a TV channel with a teletext  
broadcast  
The page numbers you have stored are  
displayed at the bottom of the screen.  
2 Set the VCR/TV/DVD switch to the  
TV position  
2 Press a colour button to choose a  
position. Then press the number  
buttons to enter the page number  
3 Press g (Text) button to display  
the teletext  
Pressing g (Text) button changes the  
mode as follows:  
3 Press and hold down the A (Store)  
button  
TEXT  
TEXT  
---  
---  
The four page numbers blink white to  
show that they are stored in memory.  
TV mode  
TV and text mode  
To call up a stored page:  
TEXT  
TEXT  
---  
---  
1 Press the B button to enter the  
List mode  
D1043-EN  
Text mode  
2 Press a colour button having a  
stored page  
4 Choose a teletext page by pressing  
the p p buttons, number buttons  
or colour buttons  
To exit the List mode:  
Press the B button again.  
To return to the TV mode:  
Press the TV/DTV button or g (Text)  
button.  
• If you have trouble receiving teletext  
broadcasts, consult your local dealer or  
the teletext station.  
• The ZOOM function will not work in  
the TV and text mode or Text mode.  
• You cannot operate menus when  
viewing a teletext programme.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Teletext function  
Hold  
Size  
You can hold a teletext page on the screen for  
as long as you want, even while several other  
teletext pages are being received.  
You can double the height of the teletext  
display.  
Press the F (Size) button  
Press the C (Hold) button  
Hold indication  
To cancel the Hold function:  
Press C (Hold) button again.  
Sub-page  
Index  
Some teletext pages include sub-pages that  
are automatically displayed.  
You can return to the index page instantly.  
Press the G (Index) button  
Returns to page 100 or a previously specified  
page.  
1 Choose a teletext page that  
includes sub-pages  
Sub-page numbers that can be viewed are  
automatically displayed at the top of the  
screen.  
Cancel  
You can search for a teletext page while  
watching TV.  
2 Press the 5 buttons to choose a  
sub-page number  
1 Press the number button to enter a  
page number, or press a colour  
button  
Reveal  
Some teletext pages include hidden text  
(such as answers to a quiz).  
The TV searches for a teletext page.  
You can display the hidden text.  
2 Press H (Cancel) button  
The TV programme appears. When the  
TV finds the teletext page, its page  
number appears in the upper left of the  
screen.  
Each time you press the E (Reveal)  
button, text is hidden or revealed  
3 Press H (Cancel) button to return  
to a teletext page when the page  
number is on the screen  
• The TV mode cannot be resumed by  
pressing the H (Cancel) button. To  
return to the TV mode press b.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Using the TV’s menu  
This TV has a number of functions you can  
operate using menus. To use all your TV’s  
functions, you need to understand the basic  
menu operating techniques fully.  
Types of menu  
PICTURE menu  
(see page 29)  
D0106  
D0107  
D0108  
D0109  
SOUND menu  
(see page 33)  
Buttons used to operate the menus  
TV/DTV  
FEATURES menu  
(see page 34)  
SET UP menu  
(see page 36)  
DTV menu  
(see page 45)  
D0224  
The menu guide area can be made to appear  
and disappear for some menus.  
While the menu is displayed, press the h  
button to change between the guide area  
being displayed and not displayed.  
Basic operation  
1 Press the H button to display  
the menu bar  
>> 4:3 AUTO ASPECT  
DTV  
PANORAMIC  
REGULAR  
14:9 ZOOM  
D0105-EN  
OK  
2 Press the 5 buttons to choose  
the menu you want to use and then  
press the a button  
D0017-EN  
Guide area  
DTV  
D1105-EN  
Chosen  
menu  
Chosen  
menu name  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
3 Press the 6 buttons to choose  
the item to be set, press the 5  
buttons to set the item, and then  
press the a button  
D1017-EN  
• The guide area for some menus will still  
be displayed even if the h button is  
pressed. This is not a fault.  
If there are sub-menus, use the 7  
buttons to operate them.  
• Press the b button to return to  
the previous menu.  
• Press the TV/DTV or H button  
to exit from the menu.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
PICTURE menu  
PICTURE  
COLOUR  
STANDARD  
PICTURE MODE  
CONTRAST  
BRIGHT  
SHARP  
COLOUR  
You can adjust the picture colour.  
2 :lighter  
HUE  
COLOUR TEMP.  
FEATURES  
3 : deeper  
COOL  
RESET  
HUE  
OK  
D0014-EN  
You can adjust the picture tint.  
2 :reddish  
3 : greenish  
• While the PICTURE menu is displayed,  
pressing the blue button will set the  
CONTRAST, BRIGHT, SHARP,  
COLOUR, HUE settings to their default  
settings.  
• You can change the HUE setting (picture  
hue) when the colour system is NTSC  
3.58, or NTSC 4.43.  
COLOUR TEMP.  
PICTURE MODE  
You can select one of three COLOUR  
TEMP. modes (three tones of white) to adjust  
the white balance of the picture. Since white  
is the colour which is used as a reference for  
all the other colours, changing the COLOUR  
TEMP. mode affects the appearance of all  
the other colours on the screen.  
You can choose one of three PICTURE  
MODEs to adjust the picture settings  
automatically.  
BRIGHT:  
Heightens contrast and sharpness.  
COOL:  
STANDARD:  
A bluish white. Using this mode when  
watching bright pictures allows you to enjoy  
a more vivid and bright picture.  
Standardizes picture adjustment.  
SOFT:  
Softens contrast and sharpness.  
NORMAL:  
The normal white colour.  
CONTRAST  
WARM:  
You can adjust the picture contrast.  
2 :lower  
3 : higher  
A reddish white. Using this mode when  
watching films allows you to enjoy colours  
that are characteristic of films.  
BRIGHT  
You can adjust the picture brightness.  
2 :darker  
3 : brighter  
SHARP  
You can adjust the picture sharpness.  
2 :softer  
3 : sharper  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
PICTURE menu  
MAX:  
FEATURES  
The level of the DIGITAL VNR effect is set  
to the maximum. If you set the DIGITAL  
VNR function to AUTO(HIGH) but still  
notice some noise, change the setting from  
AUTO(HIGH) to MAX.  
Choose FEATURES and press the a or 3  
button to display the sub-menu.  
> FEATURES  
DIGITAL VNR  
Super DigiPure  
MOVIE THEATRE  
Colour DigiPure  
COLOUR SYSTEM  
4:3 AUTO ASPECT  
AUTO(LOW)  
AUTO  
AUTO  
• The MAX setting is not suitable for high-  
quality pictures which contain very little  
noise.  
ON  
Super DigiPure  
OK  
The Super DigiPure function uses the latest  
in digital technology to give you a natural-  
looking picture. The Super DigiPure function  
includes the following two functions.  
D1015-EN  
• COLOUR SYSTEM cannot be chosen  
when watching Digital terrestrial  
broadcasting in one screen. When you are  
watching Digital terrestrial broadcasting  
(DVB-T) in the main picture and  
Analogue terrestrial broadcasting in the  
sub-picture, COLOUR SYSTEM can be  
chosen for the sub picture.  
DigiPure function:  
This function helps to create a natural-  
looking picture by eliminating unnecessary  
edges from high-contrast and crisp images.  
For images with low-contrast, edges are  
added to produce a sharper, more detailed  
picture.  
DIGITAL VNR  
You can choose from the three DigiPure  
function settings of AUTO, MIN and MAX.  
• If you set the DigiPure effect too high on  
a low-quality picture that contains a lot of  
noise, this may actually make the noise  
worse. We recommend you use the  
AUTO setting if you can.  
The DIGITAL VNR function cuts down the  
amount of ‘noise’ (‘snow’ or interference) in  
the original picture.  
You can choose from the four DIGITAL  
VNR function settings of AUTO(LOW),  
AUTO(HIGH), MIN and MAX.  
AUTO(LOW)/AUTO(HIGH):  
Picture motion compensation  
function:  
This function displays fast-moving pictures  
(for example, the players or ball in a football  
game) more smoothly and naturally on the  
screen.  
• The effect level of the picture motion  
compensation function cannot be  
changed. The effect level is the same no  
matter which of the AUTO, MIN or MAX  
settings is used.  
The TV will automatically adjust the level of  
the DIGITAL VNR effect to match the  
amount of noise in the picture, giving you the  
best possible picture.  
• If you set the DIGITAL VNR effect too  
high it can make the picture less sharp. It is  
recommended you use the AUTO(LOW)  
setting if you can. If you set the DIGITAL  
VNR function to AUTO(LOW) but still  
notice some noise, change the setting from  
AUTO(LOW) to AUTO(HIGH).  
AUTO:  
MIN:  
The TV will automatically adjust the level of  
the DigiPure effect to match the amount of  
noise in the picture, giving the best possible  
picture.  
The level of the DIGITAL VNR effect is set  
to the minimum. If you set the DIGITAL  
VNR function to AUTO(LOW) but feel that  
the sharpness of the original picture has not  
been reproduced fully, change the setting  
from AUTO(LOW) to MIN.  
• The MIN setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PICTURE menu  
MIN:  
OFF:  
The level of DigiPure effect is set to the  
minimum. When you set the Super DigiPure  
function to AUTO and notice some noise,  
change the setting from AUTO to MIN.  
• The MIN setting is not suitable for high-  
quality pictures which contain very little  
noise.  
Colour DigiPure doesn’t work. This gives a  
less clear picture than when this function is  
turned on.  
COLOUR SYSTEM  
The colour system is chosen automatically.  
However, if the picture is not clear or no  
colour appears, choose the colour system  
manually.  
MAX:  
The level of DigiPure effect is set to the  
maximum. If you set the Super DigiPure  
function to AUTO but feel that the original  
picture quality has not been reproduced fully,  
change the setting from AUTO to MAX.  
• The MAX setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
1 Choose COLOUR SYSTEM. Then  
press the a or 3 button  
The sub-menu of the COLOUR SYSTEM  
function appears.  
>> COLOUR SYSTEM  
MAIN  
SUB  
PAL  
AUTO  
OFF:  
The Super DigiPure function is turned off.  
MOVIE THEATRE  
OK  
The MOVIE THEATRE function displays a  
cinema film picture more smoothly and  
naturally on the screen.  
D0016-EN  
2 Press the 5 buttons to choose  
AUTO:  
MAIN or SUB  
The television automatically recognizes the  
type of signal and turns the function on and  
off.  
MAIN:  
You can change the colour system of the  
main-picture.  
SUB:  
You can change the colour system of the  
sub-picture.  
• Choose MAIN when a sub-picture is  
not displayed.  
ON:  
This function is turned on.  
OFF:  
This function is turned off.  
• The motion may appear unnatural when  
viewing images with the NTSC colour  
system. When the MOVIE THEATRE  
function is set to AUTO or ON, the  
motion may appear unnatural when  
viewing images with the NTSC colour  
system.  
3 Press the 6 buttons to choose  
the appropriate colour system.  
Then press the a button  
PAL:  
PAL system  
NTSC 3.58:  
NTSC 3.58 MHz system  
NTSC 4.43:  
NTSC 4.43 MHz system  
Colour DigiPure  
Makes the colour outline stand out and  
increases the sharpness giving a clearer  
picture.  
ON:  
Colour DigiPure works. Normally use with  
this function turned on.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PICTURE menu  
AUTO:  
This function detects a colour system  
from the input signal. You can only use  
this when you are viewing a picture from  
programme number PR 0 (AV), or an  
EXT terminal.  
• The AUTO function may not function  
properly if you have poor signal quality.  
If the picture is abnormal in the AUTO  
function, choose another colour system  
manually.  
• When in the Programme numbers PR 0  
(AV) to PR 99, you cannot choose NTSC  
3.58 or NTSC 4.43.  
• “COLOUR SYSTEM” cannot be chosen  
when you are watching the EXT-4  
picture.  
4:3 AUTO ASPECT  
You can choose one of three ZOOM modes,  
REGULAR, PANORAMIC or 14:9 ZOOM,  
as the ZOOM mode for the normal picture  
(4:3 aspect ratio).  
1 Choose 4:3 AUTO ASPECT then  
press the a button  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
OK  
D0017-EN  
2 Press the 6 buttons to choose a  
ZOOM mode  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SOUND menu  
SOUND  
BALANCE  
STEREO/  
BASS  
TREBLE  
BALANCE  
HEADPHONE VOLUME  
3D CINEMA SOUND  
You can adjust the volume balance between  
the left and right speaker.  
2 :turn the left speaker’s volume level up.  
3 : turn the right speaker’s volume level up.  
OK  
HEADPHONE VOLUME  
D0019-EN  
Adjust the volume of the sub-picture sound  
which is heard through the headphones when  
set to 2-pictures multi.  
2 :Reduce volume  
3 : Increase volume  
• Functions in the “SOUND” menu other  
than “HEADPHONE VOLUME” work  
for the TV speakers. They do not work for  
the sound from the headphones.  
• When the headphones are connected and  
only one screen is displayed, only  
“HEADPHONE VOLUME” can be used.  
• STEREO / I • II cannot be chosen when  
watching Digital terrestrial broadcasting  
(DVB-T).  
• When not set to 2-pictures multi, the  
headphone volume is adjusted with the  
r q (volume) buttons.  
3D CINEMA SOUND  
STEREO / I • II  
Press the 3 button to set the 3D CINEMA  
SOUND effect when 3D CINEMA SOUND  
is set to ON or MONO.  
When you are viewing a bilingual broadcast  
programme, you can choose the sound from  
Bilingual I (Sub I) or Bilingual II (Sub II). If  
you have poor reception on a stereo  
broadcast, you can change from stereo to  
mono sound so that you can hear the  
broadcast more clearly and easily.  
Choose 3D CINEMA SOUND. Then  
press the a or 3 button to display  
the sub-menu.  
> 3D CINEMA SOUND  
s: Stereo sound  
SURROUND  
BASS BOOST  
MID  
MID  
v : mono sound  
t : Bilingual I (sub I)  
u : Bilingual II (sub II)  
OK  
D0111-EN  
• The sound mode you can choose differs  
depending on the TV programme.  
• This function does not work in the EXT  
modes.  
SURROUND  
Adjust the surround effect.  
You can choose HIGH, MID or LOW.  
Choosing LOW will reduce the surround  
effect and choosing HIGH will increase the  
surround effect.  
BASS  
BASS BOOST  
You can adjust the low tone of the sound.  
2 :weaker  
3 : strong  
Adjust the bass sound.  
You can choose HIGH, MID or LOW.  
Choosing LOW will reduce the bass sound  
and choosing HIGH will increase the bass  
sound.  
TREBLE  
You can adjust the high tone of the sound.  
2 :weaker  
3 : strong  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
FEATURES menu  
To cancel the SLEEP TIMER  
function:  
Press the 2 button to set the period of  
time to “OFF”.  
FEATURES  
SLEEP TIMER  
CHILD LOCK  
APPEARANCE  
BLUE BACK  
TYPE A  
ON  
CHILD LOCK  
OK  
When there is a TV channel you do not want  
your children to watch, you can use the  
CHILD LOCK function to lock out the TV  
channel. Even when a child chooses a  
programme number (PR) for a locked TV  
channel the screen will change to blue and  
display n (CHILD LOCK) so the TV channel  
cannot be viewed. Unless you enter a pre-set  
ID number by a special operation, the lock  
cannot be released and the child cannot view  
the TV channel.  
D0023-EN  
• CHILD LOCK, APPEARANCE and  
BLUE BACK cannot be chosen when  
watching Digital terrestrial broadcasting  
(DVB-T).  
SLEEP TIMER  
You can set the TV to automatically turn off  
after a set period of time.  
1 Choose SLEEP TIMER. Then press  
the a or 3 button  
To set the CHILD LOCK function  
1 Choose CHILD LOCK, then press  
the 0 button  
A Sub-menu of the SLEEP TIMER  
function appears.  
“SET ID NO.” (ID number setting screen)  
appears.  
> SLEEP TIMER  
0
120  
> SET ID NO.  
OFF  
0040  
OK  
OK  
D0024-EN  
D0025-EN  
2 Press the 5 buttons to set the  
period of time.  
2 Set the ID number to your liking  
1 Press the 6 buttons to choose  
a number.  
Then press the a button  
You can set the period of time for up to  
120 minutes (2 hours) in 10 minute steps.  
• One minute before the SLEEP TIMER  
function turns off the TV, “GOOD  
NIGHT!” appears.  
• The SLEEP TIMER function cannot  
be used to turn off the TV’s main  
power.  
• When the SLEEP TIMER function is  
on, you can display the sub-menu of  
the SLEEP TIMER function again to  
confirm or change the remaining  
period of time of the SLEEP TIMER  
function. Press the a button to leave  
the menu after confirming or changing  
the remaining time.  
2 Press the 5 buttons to move  
the cursor.  
3 Press the a button  
The Sub-menu of CHILD LOCK appears.  
>> CHILD LOCK  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
LOCK  
OK  
D0026-EK  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
FEATURES menu  
If you have forgotten the ID  
4 Press the 6 buttons to choose a  
TV channel  
number:  
Perform step 1 of “To set the CHILD  
LOCK function”. After confirming the ID  
number, press the TV/DTV button to exit  
the menu.  
Every time you press the 6 buttons, the  
Programme number (PR) changes, and the  
picture of the TV channel registered in the  
Programme number (PR) is displayed on  
the screen.  
• Even if you reset the lock temporarily,  
it does not mean that the CHILD  
LOCK function set for the TV channel  
is cancelled. The next time anyone  
tries to view the TV channel, it will be  
locked again.  
• When you want to cancel the CHILD  
LOCK function, you must perform the  
operation “To set the CHILD LOCK  
function” again.  
5 Press the blue button and set the  
CHILD LOCK function.  
Then press the a button  
n (CHILD LOCK) appears and the TV  
channel is locked.  
To reset the CHILD LOCK function:  
Press the blue button again.  
n (CHILD LOCK) disappears.  
• To stop it being easy to choose the  
programme number (PR) of a locked  
TV channel, the programme number  
(PR) has been set so that it cannot be  
chosen with the 6 buttons or the  
buttons of the TV.  
To disable easy resetting of the CHILD  
LOCK function, the menu disappears if  
you choose the CHILD LOCK function  
and press the a button.  
• To stop it being easy to reset the lock,  
“ID NO.” (ID No. input screen) is set  
so that it cannot appear unless you  
To view a locked TV channel  
1 Choose a programme number (PR)  
of a locked TV channel with the  
number buttons or PR LIST  
The screen changes to blue and the n  
(CHILD LOCK) appears. You cannot  
view the TV channel.  
press the  
(Information) button.  
h
APPEARANCE  
Press the 5 button and choose the format  
in which the channel number is displayed  
from the three types: TYPE A, TYPE B and  
TYPE C.  
5
D0027-EN  
2 Press the  
(Information) button to  
h
display “ID NO.” (ID No. input  
screen)  
BLUE BACK  
5
You can set the TV to automatically change  
to a blue screen and mute the sound if the  
signal is weak or absent, or when there is no  
input from an external device.  
ID NO.  
:
D0028-EN  
3 Press the number buttons to enter  
the ID number  
ON:  
This function is turned on.  
The lock is temporarily released so you  
can view the TV channel.  
OFF:  
This function is turned off.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SET UP menu  
SET UP  
EDIT/MANUAL (Analogue)  
AUTO PROGRAM  
EDIT/MANUAL  
PICTURE TILT  
DECODER(EXT-2)  
EXT SETTING  
The EDIT/MANUAL functions are divided  
into two types:  
• editing the current programme numbers  
(PR) (EDIT functions); and  
OFF  
OFF  
ATTENUATOR  
• manually storing a TV channel you want  
to view on a particular programme  
number (PR) (MANUAL function).  
OK  
D0029-EN  
• AUTO PROGRAM, EDIT/MANUAL,  
PICTURE TILT and DECODER (EXT-2)  
cannot be chosen when watching Digital  
terrestrial broadcasting (DVB-T).  
Here are the details about these functions:  
MOVE:  
This function changes the programme  
number (PR) of a TV channel.  
ID:  
AUTO PROGRAM (Analogue)  
This function registers a channel name (ID)  
to a TV channel.  
You can again perform the AUTO  
PROGRAM function TV channel automatic  
registration which was performed in the  
“Initial settings” (page 8).  
To receive SKY 1 you need a satellite tuner.  
You must have the satellite tuner set to SKY  
1 before starting the AUTO PROGRAM  
function.  
INSERT:  
This function adds a new TV channel in the  
current programme numbers (PR) list by  
using the CH number.  
• You cannot use the INSERT function if  
you do not know the channel number of a  
TV channel. Use the MANUAL function  
to register a TV channel in the programme  
number (PR).  
1 Choose AUTO PROGRAM, then  
press the a or 3 button  
The AUTO PROGRAM menu appears  
and received TV channels are  
automatically stored in the programme  
numbers (PR).  
DELETE:  
This function deletes a TV channel you do  
not want to list.  
MANUAL:  
This function manually stores a new TV  
channel in a programme number (PR).  
2 Perform any extra operations you  
need to perform in step 3  
(operations after AUTO PROGRAM  
ends) and step 4 of “Initial  
settings”  
Caution  
• Using the MOVE, DELETE or INSERT  
functions rewrites the current programme  
numbers (PR) list. Therefore, the  
programme numbers (PR) of some of the  
TV channels will change.  
• Using the MANUAL function for a TV  
channel for which the CHILD LOCK  
function has been set cancels the CHILD  
LOCK function for that channel.  
• Using the MANUAL function for a TV  
channel for which the DECODER (EXT-2)  
function has been set to ON returns the  
setting of the DECODER (EXT-2) function  
for that channel to OFF.  
• When a TV channel has already been  
registered in PR 99, using the INSERT  
function deletes that TV channel.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
SET UP menu  
• The CH number is a number unique to  
the TV and corresponds to the channel  
number of a TV channel. For the  
relationship between a channel number  
and a CH number, see “CH  
Basic operation  
1 Choose EDIT/MANUAL, then press  
the a or 3 button  
The EDIT menu appears.  
NUMBER” on page 40.  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
MOVE  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
1 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
programme number (PR) changes and the  
picture of the TV channel stored in the  
programme number (PR) appears on the  
screen.  
ID  
MANUAL  
OK  
MOVE  
INSERT DELETE  
D0038-EK  
2 Follow the description for the  
function you want to use  
2 Press the 3 button to start the  
MOVE function  
> EDIT  
3 Press the a button to complete  
the settings  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
CH 21  
The T-V LINK menu appears.  
BBC2 CH 22  
ITV  
CH4  
CH5  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
T-V LINK  
DOWNLOAD TV  
RECORDING DEVICE  
OK  
STORE  
OK  
D0030-EK  
EXIT  
D0005-EN  
3 Press the 6 buttons to choose a  
If you do not have a T-V LINK  
compatible VCR connected:  
Press the TV/DTV button to exit the T-V  
LINK menu.  
new programme number (PR)  
To cancel the MOVE function:  
Press the b button.  
The T-V LINK menu disappears.  
4 Press the 2 button to change the  
programme number (PR) of a TV  
channel to a new programme  
number (PR)  
If you have a T-V LINK compatible  
VCR connected to the EXT-2 terminal:  
Follow “Downloading the data to VCR” on  
page 11 to transmit the programme number  
(PR) data.  
• For programme number PR 0, “AV”  
appears in the programme numbers (PR)  
list.  
• An EXT terminal number does not appear  
in the programme numbers (PR) list.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
DELETE  
4 Press the blue button to display the  
ID LIST (channel name list)  
1 Press the 6 buttons to choose a  
TV channel  
> EDIT  
Every time you press the 6 buttons, the  
programme number (PR) changes and the  
picture of the TV channel stored in the  
programme number (PR) appears on the  
screen.  
CH  
ID LIST  
M6  
MBC  
MCM  
MDR  
MOVIE  
MTV  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
MTV3  
M
2 Press the yellow button to delete  
the TV channel  
OK  
D0033-EK  
The TV channel is deleted from the  
programme numbers (PR) list.  
5 Press the 6 buttons to choose  
the channel name (ID)  
ID  
To cancel the ID function:  
Press the b button.  
1 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
programme number (PR) changes and the  
picture of the TV channel stored in the  
programme number (PR) appears on the  
screen.  
6 Press the a button to give a  
channel name (ID) to a TV channel  
• You can give your own unique channel  
name (ID) to the TV channel. When  
you have finished step 3, do not go to  
step 4. Press the 5 buttons to move  
to choose each character of the channel  
name (ID). Then press the a button  
to register the channel name (ID) to the  
TV channel.  
2 Press the red button to start the ID  
function  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
Before performing INSERT or  
MANUAL operation  
ID LIST  
OK  
• A CH number unique to this TV and  
corresponding to the Channel number of a  
TV channel is required. Find the  
D0031-EK  
corresponding CH number from a table  
“CH NUMBER” on page 40 based on the  
Channel number of the TV channel.  
3 Press the 6 buttons to choose  
the first character of a channel  
name (ID) you want to give the TV  
channel  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
M
ID LIST  
OK  
D0032-EK  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
INSERT  
MANUAL  
1 Press the 6 buttons to choose a  
programme number (PR) for which  
you will register a new TV channel  
1 Press the 6 buttons to choose a  
programme number (PR) for a new  
TV channel  
2 Press the green button and start  
the INSERT function  
2 Press the blue button to activate  
the MANUAL function  
> MANUAL  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
SEARCH+  
FINE-  
OK  
OK  
0
9
FINE+  
SEARCH-  
D0035-EK  
D0034-EN  
To cancel the INSERT function:  
Press the b button.  
To cancel the MANUAL function:  
Press the b button.  
3 Press the number buttons to enter  
the remaining CH number  
3 Press the green or red button to  
search for a TV channel  
Scanning stops when the TV finds a TV  
channel. Then the TV channel is  
displayed.  
The TV shifts to registration mode.  
When the registration is completed, the  
picture of the TV channel appears on the  
screen.  
• The CH number is a number given to  
each broadcast frequency that carries a  
TV channel. If the TV cannot detect  
the TV channel corresponding to the  
broadcast frequency indicated by the  
CH number, a “no-signal” picture  
appears.  
4 Press the green or red button  
repeatedly until the TV channel you  
want appears  
If the TV channel reception is poor:  
Press the blue or yellow button to fine-  
tune the TV channel.  
5 Press the a button and register  
the TV channel to a Programme  
number (PR)  
The normal EDIT menu is resumed.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SET UP menu  
CH NUMBER  
PICTURE TILT  
• When you want to use the INSERT  
function on page 39, find the CH/CC  
number corresponding to the channel  
number of the TV channel from this table.  
If you want to know a particular TV  
channel’s channel menu, look in TV  
listings magazines or contact the  
broadcaster.  
There are cases where the Earth’s magnetic  
field may make the picture tilt or make  
unnatural colours appear in the corner of the  
screen. If this happens, you can correct it.  
1 Choose PICTURE TILT, then press  
the a or 3 button  
The sub-menu of the PICTURE TILT  
function appears.  
CH  
Channel  
E21  
E22  
E23  
E24  
E25  
E26  
E27  
E28  
E29  
E30  
E31  
E32  
E33  
E34  
E35  
E36  
E37  
E38  
E39  
E40  
E41  
E42  
E43  
E44  
E45  
CH  
Channel  
E46  
E47  
E48  
E49  
E50  
E51  
E52  
E53  
E54  
E55  
E56  
E57  
E58  
E59  
E60  
E61  
E62  
E63  
E64  
E65  
E66  
E67  
E68  
E69  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
CH 30  
CH 31  
CH 32  
CH 33  
CH 34  
CH 35  
CH 36  
CH 37  
CH 38  
CH 39  
CH 40  
CH 41  
CH 42  
CH 43  
CH 44  
CH 45  
CH 46  
CH 47  
CH 48  
CH 49  
CH 50  
CH 51  
CH 52  
CH 53  
CH 54  
CH 55  
CH 56  
CH 57  
CH 58  
CH 59  
CH 60  
CH 61  
CH 62  
CH 63  
CH 64  
CH 65  
CH 66  
CH 67  
CH 68  
CH 69  
>> PICTURE TILT  
OK  
D0018-EN  
2 Press the 6 buttons until the  
picture becomes level. Then press  
the a button  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SET UP menu  
6 Turn on the VCR, and then press  
the a button to transmit the data  
to recording device  
DECODER (EXT-2)  
If you have a decoder connected to a T-V  
LINK compatible VCR, which in turn is  
connected to the EXT-2 terminal, use the  
DECODER (EXT-2) function to unscramble  
the scrambled TV channels.  
The T-V LINK menu disappears once the  
data transmission ends.  
7 If you have another TV channel  
capable of being unscrambled with  
a Decoder, repeat steps 2 to 6  
1 Turn on the decoder power  
2 Display the scrambled TV channel  
on the TV  
If the DECODER (EXT-2) function has  
been set to “ON” but the TV channel  
cannot be unscrambled, check the  
following:  
Even if the decoder is working, a  
scrambled picture appears.  
• Has the decoder been connected to the  
VCR properly according to the VCR  
and decoder instruction manuals?  
• Has the decoder power been turned  
on?  
3 Display the SET UP menu and  
choose DECODER (EXT-2)  
SET UP  
AUTO PROGRAM  
EDIT/MANUAL  
PICTURE TILT  
• Can the TV channel be unscrambled  
with a decoder?  
DECODER(EXT-2)  
EXT SETTING  
ATTENUATOR  
OFF  
OFF  
• Do you need to change the recording  
device settings in order to connect the  
decoder? Confirm that the VCR is set  
properly by rechecking the VCR  
instruction manual.  
OK  
D0029-EN  
4 Press the 5 buttons to choose  
ON  
An unscrambled picture appears.  
To cancel the DECODER (EXT-2)  
function:  
Press the 5 buttons to choose OFF.  
5 Press the a button to complete  
the setting  
The T-V LINK menu appears.  
T-V LINK  
DOWNLOAD TV  
RECORDING DEVICE  
OK  
EXIT  
D0005-EN  
You can send the programme numbers  
data to a VCR with the T-V LINK  
function.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SET UP menu  
1 Press the 5 or 6 buttons to  
EXT SETTING  
choose an EXT terminal  
> EXT SETTING  
1 Choose EXT SETTING, then press  
the a or 3 button  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
The EXT SETTING menu appears.  
> EXT SETTING  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
EXT-4  
DTV  
ID LIST  
OK  
S-IN  
EXT-4  
D0020-EN  
DTV  
ID LIST  
2 Press the yellow button and set the  
S-IN (S-VIDEO input).  
OK  
S-IN  
D0020-EN  
Then press the a button  
An S-IN (S-VIDEO input) mark is  
displayed. You can view an S-VIDEO  
signal (Y/C signal) instead of the regular  
video signal (composite signal).  
2 Follow the instructions for the  
function you want to use and  
operate the function  
S-IN:  
To cancel the S-IN (S-VIDEO input)  
setting:  
Press the yellow button and turn off S-IN (S-  
VIDEO input) mark. The regular video  
signal (composite signal) pictures are  
resumed.  
You can enjoy the high-quality picture of  
the 2 S-VIDEO signal (Y/C signal).  
ID LIST:  
devices connected for each EXT terminal.  
DUBBING:  
You can choose a signal source to be  
output from an EXT-2 terminal.  
• The EXT-1 terminal does not support S-  
VIDEO signal (Y/C signal) and you  
cannot set S-IN (S-VIDEO input) in the  
EXT-1 terminal.  
• Setting S-IN (S-VIDEO input) changes  
the head character from “E” to “S”. When  
an EXT terminal receives a normal video  
signal, “E2”, “E3” or “E5” appears on the  
display. This changes to “S2”, “S3” or  
“S5” when it receives an S-VIDEO  
signal.  
• Even a device which can output an  
S-VIDEO signal (Y/C signal) may output  
a regular video signal (composite signal)  
depending on the device setting. If a  
picture cannot appear because the S-IN  
(S-VIDEO input) setting has been made,  
read the device instruction manual  
carefully again to check for the device  
settings.  
S-IN (S-VIDEO input)  
You can connect a device (such as an S-VHS  
VCR) to enjoy the high-quality picture of the  
S-VIDEO signal (Y/C signal).  
Preparation:  
• First read the device’s instruction manual  
and “Additional preparation” on page 53  
to connect the device to the TV properly.  
Second, follow the device’s instruction  
manual to set the device so that it sends an  
S-VIDEO signal (Y/C signal) to the TV.  
• Do not set S-IN (S-VIDEO input) to an  
EXT terminal connected to a device  
which cannot output an S-VIDEO (Y/C  
signal). If it is set wrongly, a picture  
cannot appear.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SET UP menu  
ID LIST  
DUBBING  
You can store a name for each of the devices  
connected to each EXT terminal. Giving a  
name to an EXT terminal makes the EXT  
terminal number appear on the screen,  
together with its name.  
You can choose a signal source to be output  
from the EXT-2 terminal.  
You can do this with the output signals of the  
devices connected to other EXT terminals, or  
with the picture and sound from a TV  
channel you are currently viewing.  
1 Press the 5 or 6 buttons to  
choose an EXT terminal  
Caution:  
Every time you dub, check this  
DUBBING setting beforehand.  
This setting may change  
automatically when “Timers (DTV  
Timer Recording)” or “Direct Rec” of  
the T-V LINK function is used.  
2 Press the blue button to display the  
name list (ID LIST)  
> EXT SETTING  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
ID LIST  
VHS  
S-VHS  
DVC  
CAM  
SAT  
1 Press the 5 buttons to choose  
STB  
the arrow from the menu  
GAME  
DVD  
DVR  
EXT-4  
> EXT SETTING  
DTV  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
OK  
D0021-EN  
3 Press the 6 buttons to choose a  
name. Then press the a button  
The ID LIST disappears and the name is  
assigned to the EXT terminal.  
EXT-4  
DTV  
OK  
• You cannot assign an EXT terminal  
name not found in the name list (ID  
LIST).  
D0022-EN  
2 Press the 6 buttons to choose an  
EXT terminal or TV.  
To erase a name assigned to the  
EXT terminal:  
Choose a blank space.  
Then press the a button  
The arrow in the menu represents a signal  
flow. The left side of the arrow shows a  
signal source output from the EXT-2  
terminal.  
4 Press the a button to complete  
the setting  
EXT-1/EXT-3/EXT-5:  
The output signal of the device connected  
to an EXT terminal passes through the TV  
and is output from the EXT-2 terminal.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SET UP menu  
TV:  
The picture and sound of the Analogue  
terrestrial broadcasting TV channel you  
are currently viewing are output from the  
EXT-2 terminal.  
DTV:  
The picture and sound of the Digital  
terrestrial broadcasting (DVB-T) TV  
channel you are currently viewing are  
output from the EXT-2 terminal.  
• During dubbing, you cannot turn off  
the TV. Turning off the TV also turns  
off the output from the EXT-2  
terminal.  
• When you choose an EXT terminal as  
an output, you can view a TV  
programme or a picture from the other  
EXT terminal while dubbing the  
picture from a device connected to the  
EXT terminal onto a VCR connected  
to the EXT-2 terminal.  
• The RGB signals from TV games  
cannot be output. Teletext programmes  
cannot be output.  
ATTENUATOR  
Turn the attenuator ON when noise is  
introduced into the picture or sound due to  
strong electric fields.  
Normally use the TV with the attenuator  
turned OFF.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DTV menu  
1 Choose Timers and press the a  
button  
DTV  
Timers  
Configuration  
Edit PR List  
Installation  
The TIMER menu appears.  
TIMER MENU  
13:48  
15/10/2003  
Mode  
Common Interface  
No. Name  
Start End  
Date  
D0209-EN  
1
3
5
BBC ONE  
BBC ONE  
BBC ONE  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
• DTV in the menu bar can only be chosen  
broadcasting (DVB-T).  
Timers (DTV Timer Recording)  
Change Mode OK Edit timer settings  
More..  
By setting the timer, you can record a Digital  
terrestrial broadcasting (DVB-T) programme  
with a VCR connected to EXT-2 or EXT-3  
while you are out.  
• Before using DTV timer recording, the  
VCR and TV must be connected up  
correctly. For details, see “Connection  
when recording to VCR” on page 54.  
• When you have a T-V LINK compatible  
VCR connected to EXT-2, all you need to  
do is set the TV timer settings and the  
programme will be recorded.  
D0210-EN  
• When the h (Information) button is  
pressed, the help screen appears. When  
it is pressed again, the previous screen  
is returned to.  
2 Press 6 buttons to choose the  
timer number, and then press the  
a button  
The timer setting window appears.  
TIMER MENU  
13:49  
15/10/2003  
By using “Direct Rec” of the T-V LINK  
function, the Direct Rec commands are sent  
from the TV to the VCR to automatically  
start and end the recording. It is not  
necessary to set the timer on the VCR.  
• When your VCR is not T-V LINK  
compatible, you also need to set the VCR  
timer settings to match the TV timer  
settings.  
No. Name  
Start End  
Date  
Mode  
1
2
3
4
5
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
Name  
BBC ONE  
Start  
End  
Date  
Mode  
01/01/2004  
Once  
Select Programme OK Confirm Timer BACKCancel  
More..  
D0211-EN  
• The recording may not start and stop at  
exactly the right times for some  
programmes. It is recommended that you  
allow some leeway when setting the  
recording times.  
• Provided that the days and times are not  
the same, you can set up to five timer  
settings.  
3 Use the 6 buttons, number  
buttons and a button to set the  
timer  
• When setting the start time and end  
time, input 1200 for 12:00 PM, 1500  
for 3:00 PM and 0000 for 12:00 AM.  
Name:  
• When subtitles are ON, the subtitles  
displayed with the broadcast will be  
recorded. When you do not want to record  
the subtitles, you need turn OFF the  
Subtitle setting beforehand (See  
“Displaying the Subtitles” on page 24.).  
• During DTV timer recording, you are  
unable to view the SET UP menu or the  
DTV menu.  
Use the 5 buttons to choose the  
channel for which the timer is to be set.  
Press the 4 button.  
Start:  
Set the timer start time with the number  
buttons.  
• When the 5 buttons are pressed, the  
input position moves.  
Press the 4 button.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
DTV menu  
End:  
WARNING:  
Set the timer end time with the number  
buttons.  
• When the 5 buttons are pressed, the  
input position moves.  
Do not turn off the main power. The timer  
function will not work with the main  
power switched off.  
The TV power lamp begins flashing at three  
minutes before the timer start time. When  
you are watching TV at the time, a message  
appears on the screen to inform you the timer  
is about to start.  
Press the 4 button.  
Date:  
Set the date for the timer to work with the  
number buttons.  
• When the 5 buttons are pressed, the  
input position moves.  
If the TV is in Standby, the power lamp  
lights orange while timer recording is in  
progress.  
Press the 4 button.  
Mode:  
• When performing timer recording with a  
T-V LINK compatible recording device,  
test the timer recording before you record  
the programme. There are some T-V  
LINK compatible recording device that  
will not correctly receive the Direct Rec  
command from the TV.  
If the recording device does not operate  
when the recording start time is reached, it  
is not receiving the Direct Rec command  
from the TV. In this case, follow the  
instructions of “When recording on a T-V  
LINK incompatible VCR:”.  
Use the 5 buttons to choose the timer  
mode (Once/Daily/Weekly), and then  
press the a button.  
4 Prepare your VCR for recording  
When recording on a T-V LINK  
compatible VCR:  
1. Insert the videotape for recording into  
the VCR and set the recording mode.  
2. Make sure the VCR is ready to  
receive Direct Rec commands from  
the TV.  
• Make sure VCR timer settings do  
not coincide with the TV timer  
settings.  
• For details, see your VCR  
instruction manual.  
While the timer is in operation:  
• You can turn the TV on or off (Standby).  
WARNING: Do not turn off the main  
power.  
• You can watch Analogue terrestrial  
broadcasting channels or the pictures via  
an EXT terminal.  
• Please note that any programme  
information that appears on the screen,  
such as when making changes to the  
Digital terrestrial broadcasting (DVB-T)  
channel picture, will be superimposed  
over the picture in the VCR recording.  
• You cannot change Digital terrestrial  
broadcasting (DVB-T) channels while  
recording is in progress.  
When recording on a T-V LINK  
incompatible VCR:  
1. Insert the videotape for recording into  
the VCR and set the recording mode.  
2. Set the VCR recording timer settings.  
• Make the start and end time match  
that of the TV timer.  
• Set the VCR to record the signal  
from the external input that the TV  
is connected to.  
• For details, see your VCR  
instruction manual.  
Cancelling and resetting the timer  
setting:  
Cancelling the timer setting  
Display the TIMER MENU and press the  
6 buttons to choose which timer  
setting to cancel. Press the 5 buttons  
so that “Inactive” appears in the Mode  
column.  
When you have finished Step 4, you have set  
the timer.  
When you are not watching TV, make sure  
the TV is in standby.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DTV menu  
Reactivating the cancelled timer  
setting  
Display the TIMER MENU and press the  
6 buttons to choose which timer  
setting to reactivate. Press the 5  
buttons so that “Active” appears in the  
Mode column.  
• When the b button is pressed, the  
previous screen is returned to. When the  
TV/DTV or H buttons are pressed,  
the menu disappears.  
• When the h (Information) button is  
pressed, the help screen appears. When it  
is pressed again, the previous screen is  
returned to.  
Aborting the timer recording  
Display the Digital terrestrial broadcasting  
press the  
(Information) button. A  
h
Audio Language  
window will appear asking if you want to  
stop the recording. Press the button to  
abort the recording. If you want to continue  
recording, press the TV/DTV button.  
With Digital terrestrial broadcasting (DVB-  
T), a number of languages can be broadcast  
at the same time. Choose the language you  
want to listen to when watching these  
broadcasts.  
a
• If, while attempting to perform timer  
VCR, the TV timer operation starts but  
the VCR does not start recording, the  
problem is related to the VCR. Resolve  
the VCR-related problem and refer to  
“Aborting the timer recording” to  
abort the recording. After this is done,  
reset the timer.  
1 Press the 6 buttons and choose  
Audio Language  
2 Press the 5 buttons and choose  
the language  
The language changes every time the  
button is pressed.  
• If the selected language is not broadcast,  
the default language will be played.  
• When you are watching TV at the  
recording start time, you may  
encounter an error message stating that  
recording could not start because of a  
VCR-related problem. See “Direct  
Rec” on page 12, which lists and  
explains each error message.  
Subtitle language  
With Digital terrestrial broadcasting (DVB-  
T), a number of subtitles can be broadcast at  
the same time. Choose the subtitle you want  
to display when watching these broadcasts.  
1 Press the 6 buttons and choose  
Configuration  
Subtitle  
Set the basic setting for when watching  
Digital terrestrial broadcasting (DVB-T).  
2 Press the 5 buttons and choose  
a subtitle language that appears  
when the SUBTITLE button is  
pressed  
Choose configuration and press the  
a button  
CONFIGURATION appears.  
The subtitle language changes every time  
the button is pressed.  
CONFIGURATION  
Audio Language  
Subtitle  
English  
English  
Off  
Favourite Mode  
Enable/disable the Edit PR List Favourites  
settings.  
Favourite Mode  
Receiver Upgrade  
Enter PIN code  
V.3.3  
1 Press the 6 buttons and choose  
Favourite Mode  
2 Press the 5 buttons and choose  
Change preferred audio language  
More..  
ON or OFF  
D0212-EN  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
DTV menu  
On:  
2 Press the 6 buttons and choose  
Automatic Download, and press  
the 5 buttons to choose Enable  
or Disable  
The Edit PR List Favourites settings are  
enabled.  
When the p p button is pressed, only  
the channels chosen in the Edit PR List  
Favourites (those with the icon) can be  
chosen.  
• For details on how to set your  
favourite channels, see “Setting the  
favourite channels” on page 51.  
Enable (factory settings):  
The Digital terrestrial broadcasting  
(DVB-T) software is automatically  
updated every day at 3:00 am. When  
enabled, the TV also searches for new  
software whenever it goes to standby.  
Off:  
Disable:  
The Edit PR List Favourites settings are  
disabled  
When the p p button is pressed, all the  
channels registered in the Edit PR List can  
be chosen.  
The Digital terrestrial broadcasting  
(DVB-T) software is not automatically  
updated.  
Manually updating the Digital  
terrestrial broadcasting (DVB-T)  
information  
Receiver Upgrade  
Set the method to upgrade the Digital  
terrestrial broadcasting (DVB-T) receiver  
software.  
Press the 6 buttons and choose  
Search for New Version, then press  
the a button  
The Digital terrestrial broadcasting (DVB-T)  
information is updated.  
1 Press the 6 buttons and choose  
Receiver Upgrade, and press the  
a button  
The setting window appears.  
In the future, there is a possibility that the  
Receiver Update function may also be able to  
be used to update the Digital terrestrial  
broadcasting (DVB-T) software and add new  
functions.  
CONFIGURATION  
Audio Language  
Subtitle  
English  
English  
Off  
Favourite Mode  
Receiver Upgrade  
Enter PIN code  
V.3.3  
Automatic Download  
Enabled  
Search for New Version  
Switch automatic upgrade BACKExit submenu  
More..  
D0213-EN  
• The actual version may be different to  
the Receiver Upgrade version  
displayed above.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DTV menu  
Enter PIN code  
Edit PR List  
Choose Enter PIN code to change the PIN  
code for the Edit PR List menu’s “Lock”.  
The PIN code factory setting (how it is set  
when you purchase the television) is 0000.  
The Edit PR List can be used to do the  
following:  
• delete registered channels  
• edit channel names  
• lock channels so that they cannot be  
watched by children  
1 Press the 6 buttons and choose  
Enter PIN code, then press a  
button  
• set Favorites so that you can easily choose  
from only the channels you often watch.  
2 Input the current PIN code  
When you are making this setting for the  
first time, input 0000.  
Choose Edit PR List and press the a  
button  
EDIT PR LIST appears.  
When a PIN code has already been set,  
enter the correct PIN code.  
The PIN code setting window appears.  
• Sometimes you may notice a drop in  
picture quality while watching your  
programme in the quarter-screen. This is  
not a fault.  
CONFIGURATION  
Audio Language  
Subtitle  
English  
English  
Off  
Favourite Mode  
Receiver Upgrade  
Menu Lock  
V.3.5  
EDIT PR LIST  
Installation  
1
BBC ONE  
Enter PIN code  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
PIN code:  
Confirm:  
0
..  
9
Enter PIN code  
BACKExit PIN code menu  
More..  
D0225-EN  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
Select function  
Select PR OK Watch PR  
3 Press the number buttons to input  
a new PIN code (password)  
D0202-EN  
4 Input the new PIN code (password)  
again in the Confirm box  
Your newly chosen PIN code is now set.  
You will now need to use the PIN code  
(password) you chose here to lock or  
unlock the Edit PR List’s “Lock”.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
DTV menu  
3 Choose Yes and press the a  
button  
• When the b button is pressed, the  
previous screen is returned to. When the  
TV/DTV or H buttons are pressed,  
the menu disappears.  
• When the h (Information) button is  
pressed, the help screen appears. When it  
is pressed again, the previous screen is  
returned to.  
The chosen channel is deleted.  
• If you do not want to delete the chosen  
channel, choose No and press the a  
button.  
• Perform “Installation” (see page 52) to  
re-register a channel that you have  
deleted.  
Choosing a channel  
The chosen channel is shown on the quarter-  
screen.  
Editing a channel name  
1 Press the 5 buttons and choose  
Edit Name on the bar at the bottom  
of the screen  
1 Press the 5 buttons and choose  
Select on the bar at the bottom of  
the screen  
2 Press the 6 buttons and choose  
the channel to be edited, and then  
press the a button  
2 Press the 6 buttons and choose  
a channel, and then press the a  
button  
The edit window appears.  
The picture of the chosen channel is  
shown on the quarter-screen.  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
Deleting a channel  
1 Press the 5 buttons and choose  
Delete on the bar at the bottom of  
the screen  
BBC TWO  
Select  
Delete  
Edit Name  
Lock  
Favourites  
2 Press the 6 buttons and choose  
the channel to be deleted, and then  
press the a button  
Select function  
D0216-EN  
Select PR OK Edit PR name  
More..  
The channel deletion confirmation  
window appears.  
3 Press the 6 buttons and choose  
a character, press the 5 buttons  
to move the cursor and edit the  
name, and then press the a  
button  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
The selected service will be permanently  
The edited channel appears in the Edit PR  
List.  
deleted. Are you sure?  
Yes  
No  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
Select function  
Select PR OK Delete PR  
D0215-EN  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DTV menu  
When a locked channel is chosen, the  
Enter PIN code input window will appear.  
If the correct PIN code is input, the  
picture appears.  
Locking a channel  
Digital terrestrial broadcasting (DVB-T)  
channels can be locked in the same way as  
the FEATURES menu CHILD LOCK.  
1 Press the 5 buttons and choose  
Lock on the bar at the bottom of the  
screen  
• When you forget the PIN code for the  
“Lock”, you can unlock locked  
channels by performing Automatic  
Search (see “Installation” on page 52).  
2 Press the 6 buttons and choose  
the channel to be locked, and then  
press the a button  
Setting the favourite channels  
If only channels that you often watch are set  
as favourite channels, you can choose from  
just those channels when the p p buttons  
are pressed.  
The Enter PIN code input window  
appears.  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
WS 24  
• After setting the favourite channels, check  
that “Favourite Mode” in “Configuration”  
Enter PIN code  
1 Press the 5 buttons and choose  
Favourites on the bar at the bottom  
of the screen  
Select  
Delete  
More..  
0
..  
9
Enter PIN code  
2 Press the 6 buttons and choose  
the channel to be registered as a  
favourite channel, and then press  
the a button  
D0217-EN  
3 Press the number buttons to input  
the correct PIN code and press the  
a button  
The favourite icon appears to the right of  
the chosen channel.  
If you have not changed the PIN code in  
the CONFIGURATION menu’s “Enter  
PIN code” (see page 49), input 0000.  
If you have changed the PIN code in the  
CONFIGURATION menu’s “Enter PIN  
code” (see page 49), input the PIN code  
you chose.  
LIST  
The lock icon appears next to the channel  
name in the Edit PR List.  
D0219-EN  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
0
..  
9
Enter PIN code  
D0218-EN  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DTV menu  
Factory Settings:  
Installation  
Choose when you have moved house etc  
and want to automatically re-register all  
the channels.  
In addition to registering all the channels  
that can be received, it will reset the timer  
settings.  
Use when re-registering a channel or when  
registering a new channel.  
1 Choose Installation and press the  
a button  
The Installation menu appears.  
When Factory Settings is chosen and the  
a button is pressed, the confirmation  
window appears.  
Installation  
Automatic Search  
Manual Search  
Factory Settings  
Are you sure you want to delete the PR list  
and reset all settings?  
D0220-EN  
Yes  
No  
D0223-EN  
2 Press the 6 buttons and choose  
the channel registration method,  
and then press the a button  
To perform Factory Settings, choose Yes  
and press the a button.  
To cancel, choose No and press the a  
button.  
Automatic Search:  
Choose to automatically register the  
channels that can be received.  
Common Interface  
When Automatic Search is chosen and the  
a button is pressed, the confirmation  
window appears.  
Choose when a pay television reception  
module is inserted into the Common  
Interface slot on the back of the TV, and you  
want to set the module.  
Start automatic search? Current PR list  
will be replaced.  
Yes  
No  
When Common Interface is chosen and the  
a button is pressed, the name of the  
inserted module appears. When the a  
button is then pressed, the module setting  
menu appears.  
D0221-EN  
To perform Automatic Search, choose  
Yes and press the a button.  
To cancel, choose No and press the a  
button.  
• When no module is inserted, “No CI  
Module” appears.  
Manual Search:  
Choose to register a particular channel.  
• Refer to the module instruction manual  
for details of the settings.  
Installation > Manual Search  
Channel Number 61  
Signal Level:  
Signal Quality:  
Move cursor  
0
..  
9
OK Start  
More..  
Enter CH number  
D0222-EN  
Press the number buttons and input the  
channel that you want to register, and then  
press the a button. The Manual Search  
starts and the input channel is registered if  
it can be received.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Additional preparation  
Connecting external equipment  
Connect the equipment to the TV, making  
the correct rear panel and front panel  
connections.  
Before connecting anything:  
• Read the manuals that came with the  
equipment.  
Depending on the equipment, the  
connection method may be different from  
the diagram. Also, the equipment settings  
may need to change depending on the  
connection method.  
• Turn off all the equipment including the  
TV.  
• The “Specifications” on the back cover  
give the details of the EXT terminals. If  
you are connecting equipment not listed  
in the following connection diagram, see  
the table to choose the best EXT terminal.  
• Connecting cables are not supplied.  
• If the VCR’s audio output is in mono,  
connect the VCR’s AUDIO OUT (audio  
output) terminal and the TV’s EXT-5 Audio  
L/MONO terminal with an audio cable.  
1 VCR (composite signal)  
2 VCR (composite signal/S-VIDEO signal)  
3 T-V LINK compatible VCR (composite  
signal/S-VIDEO signal)  
4 Decoder  
5 DVD player (composite signal/S-VIDEO  
signal)  
6 DVD player (composite signal/RGB  
signal)  
7 DVD player (component video signals;  
Pr/Pb/Y)  
8 TV game (composite signal/RGB signal)  
9 TV game (composite signal/S-VIDEO  
signal)  
0 Headphones  
- Camcorder (composite signal/S-VIDEO  
signal)  
= SCART cable  
~ Audio cable  
! Video cable  
@ S-VIDEO cable  
# Component cable  
Side of the TV  
S
R
L/MONO  
EXT-5  
P
S
R
L/MONO  
EXT-5  
P
Back of the TV  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Additional preparation  
Equipment which can output the  
S-VIDEO signal (Y/C signal)  
Connect the equipment to an EXT terminal  
(but not the EXT-1 terminal).  
TV output from the EXT-1 terminal  
The video/sound signal of a Analogue  
terrestrial broadcasting channel you are  
viewing is always output from the EXT-1  
terminal.  
You can choose between an S-VIDEO signal  
(Y/C signal) and a regular video signal  
(composite signal). For details of how to  
operate the equipment, see “S-IN (S-VIDEO  
input)” on page 42.  
• Changing over a programme number (PR)  
also changes over the TV output from the  
EXT-1 terminal.  
• The video/sound signal from an EXT  
terminal cannot be output.  
T-V LINK compatible VCR  
Be sure to connect the T-V LINK compatible  
VCR to the EXT-2 terminal. If not, the T-V  
LINK function will not work properly.  
• When connecting a T-V LINK compatible  
VCR to the EXT-2 terminal, be sure to  
connect the decoder to the VCR. If not,  
the T-V LINK function may not work  
properly. After you have stored TV  
• Teletext programmes cannot be output.  
TV output from the EXT-3 terminal  
The video/sound signal of a Digital terrestrial  
broadcasting (DVB-T) channel you are  
viewing is always output from the EXT-3  
terminal.  
also changes over the TV output from the  
EXT-3 terminal.  
• The video/sound signal from an EXT  
terminal cannot be output.  
channels in the programme numbers (PR)  
list, set the DECODER (EXT-2) function  
for the programme number (PR) to ON to  
unscramble a scrambled TV channel. For  
details, see “EXT SETTING” on page 42.  
VCR  
Connecting headphones  
Connect the headphones with a stereo mini-  
jack (3.5 mm diameter) to the headphone  
socket at the TV rear panel.  
• When recording an Analogue terrestrial  
broadcasting, connect to either terminal  
EXT-1 or EXT-2. If you connect to the  
EXT-2 terminal, make sure the  
“DUBBING” setting (see page 43) is set  
to “TV”.  
• When recording a Digital terrestrial  
terminal EXT-2 or EXT-3. If you connect  
to the EXT-2 terminal, make sure the  
“DUBBING” setting (see page 43) is set  
to “DTV”.  
• Choose the EXT-2 terminal to connect to  
a T-V LINK compatible VCR.  
When recording an Analogue terrestrial  
broadcasting, set the “DUBBING” setting  
(see page 43) to “TV”.  
• No sound comes from the TV speakers  
when the headphones are connected and  
only one screen is displayed.  
Video or sound signal output from  
the EXT-2 terminal  
You can change over the output of the video/  
sound signal from the EXT-2 terminal. This  
is useful when you want to dub the video/  
sound from another device onto the VCR  
connected to the EXT-2 terminal. For details  
on how to do this, see “DUBBING” on  
page 43.  
When recording a Digital terrestrial  
broadcasting (DVB-T), set the  
“DUBBING” setting (see page 43) to  
“DTV”.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Additional preparation  
Connecting speakers/amplifier  
While referring to the audio equipment  
connection diagram, connect the audio  
equipment you want to the TV.  
You can use external front speakers to listen  
to the TV sound instead of the TV speakers.  
Before connecting anything:  
• Read the manuals provided with the  
amplifier and speakers.  
• Turn the TV and amplifier off.  
• To prevent magnetism from the speakers  
adversely effecting the TV screen, use  
magnetic-shielded speakers for the front  
speakers.  
• Note that connecting cables are not  
supplied.  
Back of the TV  
L
R
L
AUDIO OUT  
R
1
2
Amplifier  
Front speakers (Magnetic-shielded type)  
• The output from the AUDIO OUT  
terminal is not interrupted by headphone  
connection to the TV. You cannot cut the  
sound from the front speaker even if you  
connect a headphone to the TV.  
• Adjust the volume of the external  
speakers with the amplifier.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Troubleshooting  
Digital terrestrial broadcasting (DVB-T) service area  
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial  
broadcasting, depending on the area in which you live, you may not be able to receive Digital  
terrestrial broadcasting (DVB-T).  
For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW  
website etc.  
If a problem arises while you are using the TV, please read this troubleshooting guide carefully  
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,  
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may  
think there is a problem with the TV itself.  
Important:  
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you  
have a question when you are operating a function, read the page(s) for that function carefully,  
not this troubleshooting guide.  
• If you follow the advice in this troubleshooting guide without any success, unplug the mains  
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to  
remove the rear cover of the TV.  
If you cannot turn on the TV  
Poor picture  
• Is the mains plug connected to the mains  
outlet?  
• Is the power lamp lit? If not, press the  
main power button.  
• If noise (snow) totally blocks out the  
picture, there may be a problem with the  
aerial or aerial cable. Check the following  
to try to solve the problem:  
–Have the TV and aerial been connected  
properly?  
–Has the aerial cable been damaged?  
–Is the aerial pointing in the right  
• Make sure you set the VCR/TV/DVD  
switch to the TV position. You cannot  
turn the TV on when the VCR/TV/DVD  
switch is set to the VCR or DVD position.  
If you cannot turn off the TV  
–Is the aerial itself faulty?  
• Make sure you set the VCR/TV/DVD  
switch to the TV position. You cannot  
turn the TV off when the VCR/TV/DVD  
switch is set to the VCR or DVD position.  
• If the TV or aerial suffers interference  
from other equipment, stripes or noise  
may appear in the picture. Move any  
equipment such as an amplifier, personal  
interference away from your TV. Or try  
moving the TV. If the aerial suffers  
interference from a radio tower or high-  
voltage wire, please contact your local  
dealer.  
• If the TV suffers interference from signals  
reflecting from mountains or buildings,  
double-pictures (ghosting) will occur. Try  
to change the aerial’s direction or replace  
it with one with better directionality.  
• Are your COLOUR SYSTEM settings  
correct? Follow the description  
No picture or no sound  
poor reception? If so, the BLUE BACK  
function will be activated: the entire  
screen becomes blue, and the sound is  
muted. If you still want to view the TV  
channel, follow the description “BLUE  
BACK” on page 35 to change the BLUE  
BACK function setting to OFF.  
• If the SYSTEM setting for a TV channel  
is incorrect, it may prevent the sound  
from being issued. Follow the description  
“EDIT/MANUAL (Analogue)” on  
“COLOUR SYSTEM” on page 31 to try  
to solve the trouble.  
page 36 to use the MANUAL function to  
try to change the SYSTEM setting.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Troubleshooting  
• Have you attempted to use the remote  
• Have the COLOUR and BRIGHT settings  
been adjusted properly? Follow the  
description “BRIGHT” and “COLOUR”  
on page 29 to try to adjust them properly.  
• Videotaping teletext is not recommended  
because it may not record correctly.  
• When a white and bright still image (such  
as a white dress) is displayed on the  
screen, the white part may look as if it is  
coloured. This is unavoidable due to the  
nature of the picture tube itself, and not  
due to a TV failure. When the picture  
disappears from the screen, the unnatural  
colours will also disappear.  
• When viewing images from commercially  
available video software products, or  
videos from videotapes which have been  
recorded improperly, the top of the image  
may be distorted. This is due to the  
condition of the video signal. There is  
nothing wrong with the TV.  
• Since this TV is designed to make full use  
of the resolution of the original video  
source, the motion may appear unnatural  
when the video source is input with 625p  
progressive-scanning component signals.  
If this occurs, change the output setting of  
scanning component signal output. See  
the instructions that came with the device  
for more information.  
control from the sides or rear of the TV or  
from more than seven metres away from the  
TV? Use the remote control in front of your  
TV or from less than seven metres away.  
• When you are viewing a teletext  
programme, you cannot operate the  
menus. Press the b button to return to  
the ordinary TV programme, and then try  
operating the menus.  
• If the TV suddenly stops responding,  
press the main power button on the TV  
and turn off the main power. Press the  
main power button again to turn on the  
TV. If the TV returns to a normal state, it  
is not a failure.  
Other issues  
• When the SLEEP TIMER function  
operates, the TV is automatically turned  
off. If the TV suddenly turns off, try to  
press the # (standby) button to turn on  
the TV once again. If the TV goes back to  
normal, there is no problem.  
• When the TV is receiving a wide-screen  
signal (WSS) or a signal from an external  
device affecting the screen size, the  
ZOOM mode automatically changes.  
ZOOM mode, press the c button  
again.  
• If you bring magnetised equipment such  
as a speaker near to your TV, the picture  
may be warped or unnatural colours may  
appear at the corners of the screen. In this  
case, keep the equipment away from your  
TV. If speakers cause this to happen, use  
magnetically-shielded speakers instead.  
• A picture may be tilted due to the earth’s  
magnetic field. If so, use the “PICTURE  
TILT” on page 40 to correct the tilt.  
• It takes a short period of time from the  
time an operation such as changing  
channels is performed until an image is  
displayed. This is not a fault. This is the  
time needed for the image to stabilize  
before it can be displayed.  
Poor sound  
• Have you adjusted BASS or TREBLE  
properly? If not, follow the description  
“BASS” or “TREBLE” on page 33.  
• When TV channel reception is poor, it can  
be hard to hear stereo or bilingual sound.  
In this case, follow the description  
“STEREO / I • II” on page 33 to hear the  
sound more easily by changing it to a  
mono sound.  
If the TV does not respond to the  
remote control  
• Have the batteries of the remote control  
worn out? Follow the description “Putting  
the batteries into the remote control” on  
page 8 and replace them with new batteries.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
• The TV may make a crackling sound due  
to a sudden change in temperature. The  
picture or sound may be normal. If you  
hear crackling sounds frequently while  
you are viewing the TV, there may be  
other causes. As a precaution, ask your  
service technician to inspect it.  
• Touching the screen may cause you to  
feel a slight electric shock due to its static  
electricity. This is unavoidable due to the  
construction of the picture tube. It is not a  
problem with the TV. You can rest  
assured that this static discharge is not  
harmful.  
• When set to 2-pictures multi, adjust the  
headphone sound with HEADPHONE  
VOLUME in the SOUND menu.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
HV-32D40BK  
HV-28D40BK  
Broadcasting systems  
Colour systems  
CCIR I  
PAL  
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.  
Analogue: E21-E69, Digital (DVB-T): 474 MHz - 850 MHz (channel 21 - 68)  
NICAM (I) system  
Analogue: NICAM (I) system, Digital (DVB-T): MHEG 5 UK profile  
220 - 240 V AC, 50 Hz  
158 W (Standby: 2.0 W)  
Viewable area 76 cm  
(measured diagonally)  
Channels and frequencies  
Sound-multiplex systems  
Teletext systems  
Power requirements  
Power consumption  
Picture tube size  
148 W (Standby: 2.0 W)  
Viewable area 66 cm  
(measured diagonally)  
Audio output  
Speakers  
Rated Power output: 10 W + 10 W  
(13 cm × 6.5 cm) oval × 2  
EXT-1 terminal  
Euroconnector (21-pin, SCART)  
• Video input, Audio L/R inputs and RGB inputs are available.  
• Analogue TV broadcast outputs (Video and Audio L/R) are available.  
EXT-2 terminal  
EXT-3 terminal  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are  
available.  
• Video and Audio L/R outputs are available (EXT-1, EXT-3, EXT-5, TV, DTV).  
(The DTV signal is converted to analogue and then outputted.)  
• T-V LINK functions are available.  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
• DTV broadcast outputs (Video and Audio L/R) are available. (The DTV signal  
is converted to analogue and then outputted.)  
EXT-4 terminal  
EXT-5 terminal  
RCA connectors × 5  
• Component video (Y, Pb, Pr) inputs (625p, 525p, 625i, 525i, 1125i) and Audio  
L/R inputs are available.  
RCA connectors × 3  
S-VIDEO connector × 1  
• Video input, S-VIDEO (Y/C) input and Audio L/MONO and R inputs are  
available.  
CI slot  
DVB Common Interface is available.  
AUDIO OUT terminal  
RCA connectors × 2  
• Audio L/R outputs are available.  
• Output level 0.5 Vrms.  
Headphone jack  
Dimensions (W × H × D)  
Weight  
Stereo mini-jack (3.5 mm in diameter)  
864 mm × 587 mm × 550 mm  
55.0 kg  
762 mm × 528 mm × 493 mm  
40.0 kg  
Accessories  
Remote control unit × 1 (RM-C1805)  
AA/R6 dry cell battery × 2  
We may change the design and specifications without notice.  
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any  
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of  
the owners of copyright of the original picture sources, as this would be an infringement of  
copyright.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
LCT1596-001A-U  
0404-T-CR-JMUK  
© 2004 VICTOR COMPANY OF JAPAN, LIMITED  
Download from Www.Somanuals.com. All Manuals Search And Download.  

JL Audio Car Speaker SB D CLBR 10W1v2 User Manual
John Deere Electric Heater AC 155LP User Manual
JVC Car Stereo System GET0576 001A User Manual
JVC Flat Panel Television 5030057088 User Manual
JVC Home Theater System GVT0154 001A User Manual
Kalorik Food Processor USK HA 31535 User Manual
Kenwood Microphone MC 85 User Manual
KitchenAid Dishwasher KUDC03ITBL1 User Manual
Klipsch Portable Speaker CDT ARCHITECTURALCDT ARCHITECTURAL User Manual
Kodak Digital Camera V1233 User Manual