JVC CRT Television AV32Z10EU User Manual

ENGLISH

DEUTSCH

FRANÇAIS

NEDERLANDS

CASTELLANO

ITALIANO

PORTUGUÊS

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

! Connecting the Aerial and VCR

→

If connecting a VCR, follow A

If not connecting a VCR, follow 1.

Aerial

To operate T-V LINK functions, a T-V LINK compatible VCR

must be connected to the EXT-2 terminal on the TV. For

details about T-V LINK functions, see “T-V LINK

FUNCTIONS” on page 5.

75-ohm

Coaxial

Cable

Note:

Back of the TV

• For further details, refer to the manuals provided with the

devices to be connected.

• The connecting cables are not provided.

• A video can be viewed from the VCR without performing

For details, refer to your VCR instruction manual.

• To connect additional external devices, see “Connecting

the external devices” on page 35.

• To connect additional audio equipments, see “Using

additional audio equipments” on page 37.

• To connect a device (such as DVD player) with the digital

output terminal for Dolby Digital, see “Listening to Dolby

Digital audio” on page 36.

75-ohm

Coaxial

Cable

21-pin SCART

Cable

• When a decoder is connected to a T-V LINK compatible

VCR, set the DECODER (EXT-2) function to ON. For

details, see “Using the DECODER (EXT-2) function” on

page 34. Otherwise, you will not be able to view scrambled

channels.

To Aerial

Input

VCR

To Aerial

Output

AV IN/OUT

Terminal

! Connecting the power cord to the AC outlet

Caution:

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

! Putting Batteries into the Remote Control

Use two AAA/R03 dry cell batteries.

Insert the batteries from the

end, making sure the

and

polarities are correct.

To open the battery compartment, slide the door downwards

and lift off. Replace the door by sliding it upwards until it is

secure.

Note:

• Follow the warnings printed on the batteries.

• Battery life is about six months to one year, depending on

your frequency of use.

• If the remote control does not work properly, replace the

batteries.

• The batteries we supply are only for setting up and testing

your TV, please replace them as soon as necessary.

• Always use good quality batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

! Initial Settings

When the TV is first turned on, it enters the initial setting

mode, and the JVC logo is displayed. Follow the instructions

on the on-screen display to make the initial settings.

1 Press the Main power button on the

TV.

The Power lamp lights red (for power on), then green

(for TV on) and the JVC logo is displayed.

Power lamp

Main power

button

Note:

• If the power lamp stays red and does not change to

green:

Your TV is in the standby mode. Press the

(Standby) button on the remote control to turn your

TV on.

• The JVC logo does not appear when your TV has

been turned on once.

In this case, use the “LANGUAGE” and “AUTO

PROGRAM” functions to make the initial settings.

For details, see “INSTALL” on page 27.

2 Press the

button.

The LANGUAGE menu appears.

Yellow button

Blue button

3 Press the 5and 6buttons to

choose ENGLISH. Then press the

button.

English is set for the on-screen display description. The

COUNTRY menu appears as a sub-menu of the AUTO

PROGRAM function.

There are two COUNTRY menus. Pressing the yellow

button changes the COUNTRY menu as follows:

4 Press the 5and 6buttons to

choose the country where you are

now located.

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

5 Press the blue button to start the

9 Now, the initial settings are

complete, and you can watch the

TV.

AUTO PROGRAM function.

The AUTO PROGRAM menu appears and received TV

channels are automatically registered in the

Programme numbers (PR).

Note:

• When your TV can detect the TV channel name

from the TV channel broadcast signal, it

automatically registers the TV channel name (ID) to

the Programme number (PR) in which the TV

channel has been registered.

• If a TV channel you want to view is not set to a

Programme number (PR), manually set it using the

MANUAL function. For details, see “EDIT/

MANUAL” on page 28.

• The TV channel is not registered in Programme

number PR 0 (AV). When you want to register a TV

channel to PR 0 (AV), manually set it using the

MANUAL function. For details, see “EDIT/

MANUAL” on page 28.

If “ACI START/ACI SKIP” appears in the AUTO

PROGRAM menu:

You can use the ACI (Automatic Channel Installation)

function to decode the ACI data and complete the

registration of all the TV channels in a short period of

time. For details of the ACI function and how to use it,

refer to “Using the ACI function” on page 33.

If you don’t want to use the ACI function, press the

button to choose ACI SKIP and then press

To cancel the AUTO PROGRAM function:

Press the

button.

6 After the TV channels have been

registered in the Programme

numbers (PR), the EDIT menu

appears.

You can proceed to edit the Programme numbers (PR)

using the EDIT/MANUAL function. For details, see

“EDIT/MANUAL” on page 28.

When not using the EDIT/MANUAL function:

If you do not need to use the EDIT/MANUAL function,

go to the next step.

7 Press the

button to display the

T-V LINK menu.

8 Operate the T-V LINK menu

according to the type of a VCR

connected to the EXT-2 terminal.

When a T-V LINK compatible VCR is not

connected:

Press the

The T-V LINK menu disappears.

button to exit the T-V LINK menu.

When a T-V LINK compatible VCR is

connected:

Follow the operating procedure “Downloading the data

to VCR” on page 33 to transmit the Programme number

(PR) data.

Download from Www.Somanuals.com. All Manuals Search And Download.

T-V LINK FUNCTIONS

When a T-V LINK compatible VCR is connected to the EXT-

2 Terminal on the TV, it is easier to set up the VCR and to

view videos. T-V LINK uses the following features:

! TV Auto Power On/VCR

Image View

When the VCR starts playing, the TV automatically turns on

and the images from EXT-2 terminal are displayed on the

screen.

When the VCR menu is operated, the TV automatically turns

on and the images from EXT-2 terminal are displayed on the

screen.

To use T-V LINK functions:

A T-V LINK compatible VCR is necessary.

The VCR must be connected to the EXT-2 terminal on the TV

by a fully wired SCART cable.

Note:

• A “T-V LINK compatible VCR” means a JVC VCR with the

T-V LINK logo or a VCR with one of the following logos.

However, these VCRs may support some or all of the

features described below. For details, refer to your VCR

instruction manual.

Note:

• This function does not operate if your TV’s main power is

turned off. Set your TV’s main power to on (standby mode).

“Q-LINK” (a trademark of Panasonic Corporation)

“Data Logic” (a trademark of Metz Corporation)

“Easy Link” (a trademark of Phillips Corporation)

“Megalogic” (a trademark of Grundig Corporation)

“SMARTLINK” (a trademark of Sony Corporation)

! Pre-set Download

Download the registered data on the TV channels from the TV

to the VCR.

The Preset Download function automatically begins when the

initial setting is complete or whenever the AUTO PROGRAM

or EDIT/MANUAL operations are performed.

Note:

• This function can be operated via VCR operation.

When “FEATURE NOT AVAILABLE” is displayed:

If “FEATURE NOT AVAILABLE” is displayed, the download

was not performed correctly. Before trying to download again,

ensure the following:

• The VCR power is turned on.

• The VCR is T-V LINK compatible.

• The VCR is connected to the EXT-2 terminal.

• The SCART cable is fully wired.

! Direct Rec

“What You See Is What You Record”

You can record to VCR the images that you are currently

viewing on TV by a simple operation.

For details, read the manual for your VCR.

Operate via the VCR. “VCR IS RECORDING” is displayed.

In the following conditions, the VCR will stop

recording if the TV is turned off, if the TV channel

or input is switched, or if the menu is displayed on

the TV:

• When recording images from an external device connected

to the TV.

• When recording a TV channel after it has been

unscrambled on a decoder.

• When recording a TV channel by using the TV’s output

because that TV channel cannot be properly received on

the VCR’s tuner.

Note:

• Operation via the TV is not possible.

• Generally, the VCR cannot record a TV channel that

cannot be received properly by the VCR’s tuner, even

though you can view that TV channel on the TV. However,

some VCRs can record a TV channel by using the TV’s

output if that channel can be viewed on the TV, even

though the TV channel cannot be received properly by the

VCR’s tuner. For details, refer to your VCR instruction

manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

! Turn the Main power on

Press the Main power button on the TV.

The Power lamp lights red and your TV is in the standby

mode.

Note:

• If the Power lamp lights green, the TV is already on.

To turn the Main power off:

Press the Main power button again.

The Power lamp goes off.

Power lamp

Main power

button

Caution:

• The main power button on the TV does not fully isolate the

TV from the AC supply. If you are not going to use this TV

for a long period of time, be sure to disconnect the AC plug

from the AC socket.

! Turn the TV on from standby mode

Press the

button, the

buttons.

(Standby) button, the b

buttons or the Number

The Power lamp lights red to green and your TV will be turned

on.

To turn the TV off:

Press the

(standby) button again.

The Power lamp changes from green to red and the TV enters

standby mode.

Number

buttons

! Choose a TV channel

Choose a Programme number (PR) in which the desired

Programme TV channel has been set.

Use the 6buttons:

Press the 6buttons to choose the desired Programme

number (PR).

Use the Number buttons:

Enter the desired Programme number (PR) with the Number

buttons.

Example:

→

• PR 12

press 1 and 2.

→

• PR 6

press 6.

Use the PR LIST:

1 Press the

(Information) button to

display the PR LIST.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

Use the 6buttons:

Press the 6buttons to choose an EXT terminal.

2 Press the

and

buttons to

choose a Programme number (PR). Then

press the

button.

Use the PR LIST:

Note:

1 Press the

(Information) button to

• For Programme numbers (PR) with the CHILD

LOCK function set, the (CHILD LOCK) mark is

display the PR LIST.

displayed next to the Programme number (PR) in

the PR LIST.

2 Press the

and

buttons to

choose an EXT terminal. Then press the

• You cannot use the

buttons to choose a

Programme number (PR) with the CHILD LOCK

funtion set.

• Even if you try to choose a Programme number

a button

Note:

• The EXT terminals are registered after the

Programme number PR 99.

• You can choose a video input signal from the S-

VIDEO signal (Y/C signal) and regular video signal

(composite signal). For details, see “S-IN (S-VIDEO

input)” on page 23.

• When listening to Dolby Digital audio, see

“Listening to Dolby Digital audio” on page 36.

• If you do not have a clear picture or no colour

appears, change the colour system manually. See

“COLOUR SYSTEM” on page 17.

(PR) with the CHILD LOCK function set, the

(CHILD LOCK) mark will appear, and you cannot

watch the TV channel. To watch the TV channel,

see “CHILD LOCK” on page 25.

• If you do not have a clear picture or no colour

appears, change the colour system manually. See

“COLOUR SYSTEM” on page 17.

• If the picture is tilted, correct it. See “PICTURE

TILT” on page 17.

! Adjust the volume

• When choosing an EXT terminal with no input

signal, the EXT terminal number becomes fixed on

the screen.

Press the

buttons to adjust the volume.

The Volume indicator appears and the volume changes as

you press the qbuttons.

• This TV set has a function which can automatically

change over the input according to a special signal

output from an external device. (The EXT-4

terminal does not support it.)

To listen to the sound using headphones:

See “HEADPHONE” on page 19.

To return to a TV channel:

Press the

buttons.

button, the 6buttons or the Number

! Watch images from external

devices

To use the Programme number PR 0 (AV):

When the TV and VCR are connected only by the Aerial

cable, choosing the Programme number PR 0 (AV)

allows you to view images from the VCR. Set the VCR

RF channel to the Programme number PR 0 (AV)

manually. For details, see “EDIT/MANUAL” on page 28.

Choose an EXT terminal to which the desired external device

has been connected.

Use the

Press the

Pressing the

button:

button to choose an EXT terminal.

Pressing the

follows:

button changes the choice as

button changes the choice as follows:

TV mode

EXT modes

TV mode

Programme

numbers

PR 1 – PR 99

Programme

numbers

PR 1 – PR 99

Note:

• The VCR RF channel is sent as the RF signal from

the VCR.

• Also refer to your VCR instruction manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

! Operating with the buttons on the TV

1 Press the P pbuttons to turn the

Behind the Cover

TV on from standby mode.

2 Press the P pbuttons to choose

a Programme number (PR) or an

EXT terminal.

3 Press the r(Volume) button and

the qbuttons to adjust the

volume.

1 Press the r(Volume) button.

The volume level indicator appears.

2 Press the qbuttons while the

volume level indicator is displayed.

Note:

• The buttons on the TV cannot be used to adjust the

volume of the headphones.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL BUTTONS AND FUNCTIONS

1 Muting Button

You can turn the volume off instantly.

Press the

Volume. Pressing the

again resumes the previous Volume level.

(Muting) button to turn off the

(Muting) button

2 Number Buttons

You can choose a Programme number (PR)

by entering the Programme number.

Example:

→

• PR 12

press 1 and 2.

→

• PR 6

press 6.

You can also press the

an EXT terminal.

button repeatedly to choose

3 ZOOM Button

You can change the screen size according to the picture

aspect ratio. Choose the optimum one from the following

ZOOM modes.

AUTO:

For any picture format except Normal Picture (4:3 Aspect

Ratio), the picture will be automatically displayed in the

optimum screen size.

For Normal Picture (4:3 Aspect Ratio), the picture displayed

in accordance with the ZOOM mode set on the 4:3 AUTO

ASPECT menu. For details, see “4:3 AUTO ASPECT” on

page 17.

Note:

• AUTO may not function properly with poor signal quality. In

this case, choose an optimum ZOOM mode manually.

• This TV supports WSS (wide-screen signals). When

broadcasts with WSS are received with the ZOOM mode

set at AUTO, the most suitable ZOOM mode is

automatically chosen according to the WSS received.

REGULAR:

Use to view a normal picture (4:3 aspect ratio) as its original

size is.

PANORAMIC:

This mode stretches the left and right sides of a normal

picture (4:3 Aspect Ratio) to fill the screen, without making the

picture appear unnatural.

Note:

• The top and bottom of the picture are slightly cut off.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL BUTTONS AND FUNCTIONS

14:9 ZOOM:

Adjusting the visible area of the

This mode zooms up the Wide Picture (14:9 Aspect Ratio) to

the upper and lower limits of the screen.

picture

If subtitles or the top (or bottom) of the picture are cut off,

adjust the visible area of the picture manually.

1 Press the

button.

The ZOOM menu appears.

16:9 ZOOM:

2 Press the

button to display the ZOOM

This mode zooms up the Wide Picture (16:9 Aspect Ratio) to

the full screen.

mode indication.

Indicator is displayed.

16:9 ZOOM SUBTITLE:

This mode zooms up the Wide Picture (16:9 Aspect Ratio)

with subtitles to the full screen.

3 While it is displayed, press the

buttons to adjust the visible area

vertically.

Note:

• You cannot adjust the visible area in REGULAR or

FULL mode.

FULL:

4 3D Button

This mode uniformly stretches the left and right sides of a

normal picture (4:3 aspect ratio) to fill the wide TV screen.

You can turn the 3D-PHONIC function on or off by one-

touch operation.

Press the 3D button.

Pressing the 3D button changes the function as follows:

Note:

• Use for pictures with a 16:9 aspect ratio that have been

squeezed into a normal picture (4:3 aspect ratio), you can

restore their original dimensions.

3D-PHONIC

SURROUND OFF

! Choose the ZOOM mode

1 Press the

button to display the

Previous surround function

ZOOM menu.

Note:

• For details, see “3D-PHONIC” on page 20.

• If another surround function is activated before you press

the 3D button, you can return to that surround function.

• The 3D button does not work while the headphones are

connected to the TV.

2 Press the

buttons to choose a ZOOM

mode. Then press the

The picture expands and the chosen ZOOM mode is

displayed in about 5 seconds.

button.

Note:

• The ZOOM mode may be automatically changed

due to the control signal from an external device.

When you want to return to the previous ZOOM

mode, choose the ZOOM mode again.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL BUTTONS AND FUNCTIONS

5 Information Button

9 Colour Buttons

You can display the PR LIST or the Current Time on the

screen.

The colour buttons are used for the teletext operations or the

menu operations. For details, see “~ Teletext Control

Buttons and VCR PDVD Switch” on page 12 or “MENU

OPERATION” on page 14.

Press the

(Information) button.

(Information) button changes the display as

Pressing the

follows:

0 OK Button

The

button is used to operate menus. For details, see

“MENU OPERATION” on page 14.

Buttons

You can choose a Programme number (PR) or an EXT

terminal.

Press the

buttons to choose an

Programme number (PR) or an EXT terminal.

No indication

The

buttons are also used to operate menus.

For details, see “MENU OPERATION” on page 14.

= VCR/DVD Control Buttons and

VCR P DVD Switch

Note:

• You can choose Programme numbers (PR) or EXT

terminals with the PR LIST. For details, see “Use the PR

LIST:” on page 6.

• This TV uses teletext data to set the current time. If the TV

has not received a TV channel that has teletext

programmes since it was turned on, the time display is

blank. To view the current time, choose a TV channel that

has teletext programmes. The time will still be displayed as

long as you do not turn off the TV, even if you choose other

TV channels.

These buttons can be used to operate a JVC brand VCR or

DVD player. Pressing the button having the same

appearance as the original remote control button of a device

makes the function work in the same way as the original

remote control.

1 Set the VCR PDVD Switch to the VCR or

DVD position.

VCR:

When you are operating the VCR, set the switch to the

VCR position.

• When watching videos, an incorrect current time is

sometimes displayed.

• The

(Information) button is also used to operate menus.

DVD:

When you are operating the DVD player, set the switch

to the DVD position.

For details, see “MENU OPERATION” on page 14.

6 TV Button

2 Press the VCR/DVD Control Button to

control your VCR or DVD player.

You can return to a TV channel instantly.

Press the

button.

Note:

The TV returns to the TV mode and a TV channel appears.

• If your device is not made by JVC, these buttons

cannot be used.

Note:

• Even if your device is made by JVC, some of these

buttons or any one of the buttons may not work,

depending on the device.

• The

button is also used to operate menus. For details,

see “MENU OPERATION” on page 14.

• You can use the

channel. The VCR will receive or choose the

chapter the DVD player plays back.

buttons to choose a TV

7 5Buttons

You can adjust the volume.

Press the 5buttons to adjust the sound.

Note:

• The 5buttons are also used to operate menus. For

details, see “MENU OPERATION” on page 14.

• Some DVD player models use the

both operating of Fast forward/backward functions

and choosing the chapter. In this case, the

the buttons do not work.

buttons for

2233

8 Standby Button

Press the

on or off.

(Standby) button to turn the TV

When the TV is turned on, the power lamp changes from red

to green.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL BUTTONS AND FUNCTIONS

~ Teletext Control Buttons and VCR P DVD Switch

4 Choose a teletext page by pressing the

buttons, Number buttons or Colour

buttons.

To return to the TV mode:

Press the

button or

(Text) button.

Note:

• If you have trouble receiving teletext broadcasts,

consult your local dealer or the teletext station.

• The ZOOM function will not operate in the TV and

text mode or Text mode.

• No menu operations are possible when viewing a

teletext programme.

• Language display depends on the country which

was set on the COUNTRY menu. If characters on a

Teletext programme do not appear properly,

change the COUNTRY Setting to other country’s.

For detail, “Changing the COUNTRY setting” on

page 33.

Using the List Mode

You can store the numbers of your favourite teletext pages in

memory and call them up quickly using the colour buttons.

To store the page numbers:

1 Press B button to engage the List

Basic operation

mode.

You can view three types of teletext broadcasts on the TV:

FLOF (Fastext), TOP and WST.

The stored page numbers are displayed at the bottom

of the screen.

1 Choose a TV channel with a teletext

broadcast.

2 Press a Colour button to choose a

position. Then press the Number buttons

to enter the page number.

2 Set the VCR PDVD switch to the

(Text) position.

3 Press g (Text) button to display the

teletext.

3 Press and hold down (Store) button.

Pressing g (Text) button changes the mode as

follows:

The four page numbers blink white to indicate that they

are stored in memory.

To call up a stored page:

1 Press the B button to engage the List

mode.

TV and Text mode

TV mode

2 Press a colour button to which a page

has been assigned.

To exit the List mode:

Press the

button again.

Text mode

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL BUTTONS AND FUNCTIONS

Hold

Size

You can hold a teletext page on the screen for as long as you

want, even while several other teletext pages are being

received.

You can double the height of the teletext display.

Press the

(size) button.

Press the

(Hold) button.

Hold indication

To cancel the Hold function:

Press

(Hold) button again.

Sub-page

Index

Some teletext pages include sub-pages that are

automatically displayed.

You can return to the index page instantly.

You can hold any sub-page, or view it at any time.

Press

(Index) button.

1 Press the

(Sub-page) button to

FLOF (Fastext)/TOP/WST:

Returns to page 100 or a previously specified page.

operate the Sub-page function.

Sub-page numbers are displayed at the left of the

screen.

List mode:

Returns to the page number displayed in the lower left area

of the screen.

Colour*

Yellow

Meaning of sub-page number

Currently being displayed.

Can be displayed.

Cancel

White

You can search for a teletext page while watching TV.

Blue or Red

Cannot be displayed and it is not sent.

*: Background color of the sub-page number.

1 Press the Number button to enter a page

number, or press a Colour button.

The TV searches for a teletext page.

2 Press the 6buttons to choose a sub-

page number.

2 Press

(Cancel) button.

To cancel the Sub-page function:

Press the

(Sub-page) button again.

The TV programme appears. When the TV finds the

teletext page, its page number appears in the upper left

of the screen.

Reveal

Some teletext pages include hidden text (such as answers to

a quiz).

3 Press

(Cancel) button to return to a

teletext page when the page number is on

the screen.

You can display the hidden text.

Each time you press the

text is hidden or revealed.

(Reveal) button,

Note:

• The TV mode cannot be resumed even by pressing

the

(Cancel) button. A TV programme is

temporarily displayed instead of the teletext

programme.

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU OPERATION

This TV has a number of functions you can operate using

menus. To fully utilize all your TV’s functions, you need to

understand the basic menu operating techniques fully.

4 Press

button to complete the

setting.

The menu disappears.

1 Press the

button to display the

MENU (main menu).

To return to the previous menu:

Press

(information) button.

The MENU (main menu) appears. In it, the titles of the

menus are displayed.

To exit a menu instantly:

Press the

button.

Note:

• When watching the television with the NTSC

system, the menus are displayed at about half of

their normal vertical size.

Note:

• The title of the DIGITAL SURROUND menu is not

displayed while the headphones are connected to

the TV.

2 Press the

buttons to choose a

menu title, and press the

button.

The menu appears.

3 Operate the menus according to the

operation description of each

function.

Note:

• For details, refer to the operation descriptions of

each function described for each menu which

follows this “MENU OPERATION”.

• The display appearing at the bottom of a menu

indicates a button on the remote controller you can

use when you operate a chosen function.

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE SETTING

! Picture Adjustment

You can change the picture settings of each TINT mode as

you like.

The picture settings changed are stored in the TINT mode.

1 Press the6buttons to choose an item.

2 Press the 5 buttons to change the

setting.

Item

To display the PICTURE SETTING menu:

CONTRAST

Lower

Higher

(picture contrast)

1 Press the

button to display MENU

(main menu).

BRIGHT

(picture brightness)

Darker

Softer

Brighter

Sharper

Deeper

2 Press the 6 button to choose

PICTURE SETTING, and press the

button.

SHARP

(picture sharpness)

COLOUR

(picture colour)

Lighter

Reddish

! TINT

You can select one of three TINT modes (three kinds of

picture settings) to adjust the picture settings automatically.

HUE

(picture hue)

Greenish

1 Press the 6buttons to choose TINT.

2 Pres 5buttons to choose a mode.

Note:

• You can change the HUE setting (picture hue) only

when the colour system is NTSC 3.58 or NTSC

4.43.

COOL:

A cool white colour base with a boost in the colour and

contrast levels that creates a more vivid picture.

To return to the default settings in each TINT

mode:

Press the blue button.

WARM:

Returns the picture settings in the currently chosen

TINT mode to the default settings, and stores them in

the TINT mode again.

A warm orange/red colour base that creates the

appropriate colour and contrast levels for watching

films.

NORMAL:

3 Press the

settings.

button to complete the

A normal white colour base with normal colour and

contrast levels.

The menu disappears.

3 Press the

setting.

button to complete the

! ECO MODE

The menu disappears.

When you set the ECO MODE function to ON, the screen

contrast is automatically adjusted to a setting suitable for the

brightness of your room. This reduces eye strain for you and

the power consumption of the TV.

1 Press 6 buttons to choose ECO

MODE.

2 Press 5 buttons to choose ON.

To cancel the ECO MODE function:

Press

buttons to choose OFF.

3 Press the

setting.

button to complete the

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE FEATURES

! DigiPure Pro

The DigiPure Pro function uses the latest in digital technology

to give you a natural looking picture. The DigiPure Pro

function includes the following two functions.

DigiPure function:

This function helps to create a natural looking picture by

eliminating unnecessary edges from high-contrast and crisp

images. Conversely, for images with low-contrast, edges are

added to produce a sharper, more detailed picture.

You can choose from the three DigiPure function settings of

AUTO, MIN and MAX.

To display the PICTURE FEATURES menu:

1 Press the

button to display MENU

Note:

(main menu).

• If you set the DigiPure effect too high on a low-quality

picture that contains a lot of noise, this may actually make

the noise worse. It is recommended to use the AUTO

setting if you can.

2 Press the 6 button to choose

PICTURE FEATURES, and press the

a button.

Picture motion compensation function:

This function displays fast-moving pictures (for example, the

players or ball in a football game) more smoothly and

naturally on the screen.

! DIGITAL VNR

The DIGITAL VNR function cuts down the amount of noise in

the original picture.

Note:

You can choose from the three DIGITAL VNR function

settings of AUTO, MIN and MAX.

• The effect level of the picture motion compensation

function cannot be changed. The effect level is the same

no matter which of the AUTO, MIN or MAX settings is used.

Note:

• If you set the DIGITAL VNR effect too high it can make the

picture less sharp. It is recommended to use the AUTO

setting if you can.

1 Press the 6buttons to choose

DigiPure Pro.

1 Press the 6 buttons to choose

2 Press the 5buttons to choose a

DIGITAL VNR.

setting.

2 Press the 5 buttons to choose a

AUTO:

setting.

The TV will automatically adjust the level of the DigiPure

effect to match the amount of noise in the picture, giving

the best possible picture.

AUTO:

The TV will automatically adjust the level of the

DIGITAL VNR effect to match the amount of noise in the

picture, giving you the best possible picture.

MIN:

The level of DigiPure effect is set to the minimum. When

you set the DigiPure Pro function to AUTO and notice

some noise, change the setting from AUTO to MIN.

• The MIN setting is not suitable for high-quality pictures

which contain very little noise.

MIN:

The level of the DIGITAL VNR effect is set to the

minimum. If you set the DIGITAL VNR function to AUTO

but feel that the sharpness of the original picture has not

been reproduced fully, change the setting from AUTO to

MIN.

MAX:

The level of DigiPure effect is set to the maximum. If you

set the DigiPure Pro function to AUTO but feel that the

original picture quality has not been reproduced fully,

change the setting from AUTO to MAX.

• The MAX setting is not suitable for low-quality pictures

which contain a lot of noise.

• The MIN setting is not suitable for low-quality pictures

which contain a lot of noise.

MAX:

The level of the DIGITAL VNR effect is set to the

maximum. If you set the DIGITAL VNR function to

AUTO but still notice some noise, change the setting

from AUTO to MAX.

OFF:

The DigiPure Pro function is turned off.

• The MAX setting is not suitable for high-quality

pictures which contain very little noise.

3 Press the

setting.

button to complete the

3 Press the

setting.

button to complete the

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE FEATURES

! COLOUR SYSTEM

! 4:3 AUTO ASPECT

The colour system is chosen automatically. However, if the

picture is not clear or no colour appears, choose the colour

system manually.

You can choose one of three ZOOM modes, REGULAR,

PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the

normal picture (4:3 aspect ratio).

1 Press the

buttons to choose

1 Press the

buttons to choose 4:3

AUTO ASPECT. Then press the

COLOUR SYSTEM. Then press the

button.

The Sub-menu of the COLOUR SYSTEM function

appears.

button.

The Sub-menu of the 4:3 AUTO ASPECT function

appears.

2 Press the

mode.

buttons to choose a ZOOM

button to complete the

2 Press the 5 buttons to choose the

appropriate colour system.

3 Press the

settings.

PAL:

PAL system

The menu disappears.

SECAM:

SECAM system

! PICTURE TILT

NTSC 3.58:

NTSC 3.58 MHz system

There are cases where the Earth’s magnetic force may make

the picture tilt. If this happens, you can correct the picture tilt.

NTSC 4.43:

NTSC 4.43 MHz system

1 Press the 6 buttons to choose

AUTO:

PICTURE TILT. Then press the

button.

This function detects a colour system from the input

signal. Only when you are viewing a picture from

Programme number PR 0 (AV), or EXT terminal, you

can choose using the AUTO function.

The Sub-menu of the PICTURE TILT function appears.

3 Press the

setting.

button to complete the

The menu disappears.

Note:

• The AUTO function may not function properly if you

have poor signal quality. If the picture is abnormal

in the AUTO function, choose another colour

system manually.

• When in the Programme numbers PR 0 (AV) to PR

99, you cannot choose NTSC 3.58 or NTSC 4.43.

becomes level.

2 Press the

buttons until the picture

button to complete the

3 Press the

setting.

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

SOUND SETTING

! Sound Adjustment

You can adjust the sound to your liking.

1 Press the6buttons to choose an item.

2 Press the 5 buttons to adjust it.

Item

Weaker

Left

BASS

Stronger

Right

TREBLE

BALANCE

To display the SOUND SETTING menu:

1 Press the

button to display MENU

3 Press the

setting.

button to complete the

(main menu).

2 Press the

button to choose

The menu disappears.

SOUND SETTING. Then press the

button.

Note:

• When the 3D-PHONIC function or DOLBY DIGITAL

function is operating, the “BALANCE” item does not

appears.

! STEREO / I•II

When you are viewing a bilingual broadcast programme, you

can choose the sound from Bilingual I (Sub I) or Bilingual II

(Sub II). When the stereo broadcasting is received poorly,

you can change from stereo to mono sound so that you can

hear the broadcast more clearly and easily.

! BBE

You can use the BBE function to enjoy easy-to-listen sound

that is faithful to the original sound recorded.

1 Press the 6 buttons to choose BBE.

2 Press the 5 buttons to choose ON.

1 Press the

buttons to choose

STEREO / I • II.

To cancel the BBE function:

Press the 5 buttons to choose OFF.

2 Press the

buttons to choose a

sound mode.

3 Press the

setting.

button to complete the

Stereo sound

mono sound

The menu disappears.

Bilingual I (sub I)

Bilingual II (sub II)

• Licensed by BBE Sound, Inc. BBE is a registered

trademark of BBE Sound, Inc.

3 Press the

setting.

button to complete the

! SPEAKER

• Set the SPEAKER function to OFF when external front

speakers are connected to the TV. If the SPEAKER

function is set to OFF, no sound is emitted from the TV

speakers.

The menu disappears.

Note:

• The sound mode you can choose differs depending

on the TV programme.

• This function does not work in the EXT modes. And

this function does not appear in the SOUND

SETTING menu.

1 Press the 6 buttons to choose

SPEAKER.

2 Press the 5 buttons to choose ON or

OFF.

3 Press the

setting.

button to complete the

The menu disappears.

Note:

• To emit the sound from the TV speakers, set the

SPEAKER function to ON.

• The “SPEAKER” item is not displayed when the 3D-

PHONIC function or DOLBY DIGITAL function are

operating.

Download from Www.Somanuals.com. All Manuals Search And Download.

SOUND SETTING

! SUBWOOFER

Set the SUBWOOFER function to ON when the subwoofer is

connected to the TV.

1 Press the 6buttons to choose

SUBWOOFER.

2 Press the 5buttons to choose ON or

OFF.

3 Press the a button to complete the

setting.

The menu disappears.

Note:

• Set the SUBWOOFER function to OFF when the

subwoofer is not connected to the TV.

• When the 3D-PHONIC function or DOLBY DIGITAL

function is operating, the “SUBWOOFER” item

does not appear.

! HEADPHONE

You need to use the HEADPHONE menu in order to adjust

the volume of the headphones.

Use of the HEADPHONE menu also makes it possible to

select whether or not sound is emitted from the TV speakers

when using the headphones.

1 Press the 6buttons to choose

HEADPHONE. Then press the a button.

The sub-menu of the HEADPHONE function appears.

2 Change the setting.

To adjust the volume of the headphones:

Use the 6buttons to choose VOLUME and use the

5buttons to adjust the volume.

To prevent the sound from being emitted from

the TV speakers when the headphones are in

use:

Use the 6buttons to choose TV SPEAKER and use

the 5buttons to select OFF.

Note:

• The sound will be emitted from the TV speakers

even when listening with the headphones if the TV

SPEAKER is turned ON.

3 Press the a button to complete the

setting.

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL SURROUND

• This function does not work properly except for Dolby

Surround encoded programmes and Dolby Digital

programmes.

! DOLBY DIGITAL

You can enjoy the surround sound of Dolby* Digital

programmes and Dolby Surround encoded programmes.

When viewing a programme from the EXT terminal

which has been set to DIGITAL-IN:

You can enjoy the surround sound of Dolby Digital

programmes.

If the programme source has 5.1-channel Dolby Digital

soundtracks, you can enjoy the 5.1-channel Dolby Digital

surround sound.

You can enjoy the surround sound with any of the five

surround functions.

1 Press the a button to display MENU

(main menu).

When viewing the Dolby Surround encoded programmes,

you can enjoy the Dolby Surround Pro Logic surround sound.

2 Press the 6buttons to choose

DIGITAL SURROUND. Then press the OK

button.

When viewing a programme from the EXT terminal

which has not been set to DIGITAL-IN, or when

viewing a TV broadcasting programme:

When viewing the Dolby Surround encoded programmes,

you can enjoy the Dolby Surround Pro Logic surround sound.

• The DIGITAL SURROUND menu is not displayed

while the headphones are connected to the TV.

Disconnect the headphones from the TV.

• Additional surround speakers are necessary in order to use

this function to enjoy surround sound. Although you can

listen to Dolby Digital audio without surround speakers, you

cannot enjoy surround sound such as 5.1-channel Dolby

Digital surround sound.

• Before using this function, correctly set each of the items in

the DOLBY DIGITAL menu in accordance with “DOLBY

DIGITAL setting” on page 21.

• Dolby Digital soundtracks can provide anything from mono

to full 5.1-channel Dolby Digital surround sound. When a

Dolby Digital audio signal is received, the number of front

channels and rear channels included in the signal are

displayed on the screen for a few seconds as “DOLBY D

(number of front channels) / (number of rear channels)”. If

LFE (low frequency effects) are included in the signal, “ .1”

is displayed after the number of rear channels. For

example, “DOLBY D 3/2.1” is displayed when a 5.1-

channel Dolby Digital signal is received.

3 Press the 6buttons to choose the

function you want to use.

To cancel a surround function:

Press the 6buttons to choose SURROUND OFF.

4 Press the a button to complete the

setting.

The menu disappears.

! 3D-PHONIC

Dolby Surround Pro Logic surround sound and Dolby Digital

surround sound can be easily enjoyed without additional

surround speakers.

Using rear surround signals of Dolby Surround encoded

programmes or Dolby Digital programmes, this function will

create the surround sound as if surround speakers were

located to your right and left.

• This function does not work properly except for Dolby

Surround encoded programmes and Dolby Digital

programmes.

When viewing a programme from the EXT terminal

which has been set to DIGITAL-IN:

You can enjoy the atmosphere of the surround sound of

Dolby Digital programmes.

If the programme source has 5.1-channel Dolby Digital

soundtracks, you can enjoy the atmosphere of the 5.1-

channel Dolby Digital surround.

* Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are

trademarks of Dolby Laboratories.

Note:

When viewing Dolby Surround encoded programmes, you

can enjoy the atmosphere of Dolby Surround Pro Logic

surround sound.

• Dolby Digital is an advanced form of digital audio coding.

Dolby Digital audio is available from programme sources

(such as DVD-video discs) which are usually identified with

a Dolby Digital logo.

• When you connect the subwoofer system to the TV, you

can enjoy the powerful low frequency effects (LFE) of 5.1-

channel Dolby Digital more effectively.

• This TV does not work with digital audio signals other than

Dolby Digital audio. If no sound is emitted from the

speakers, cancel the DIGITAL-IN setting and change to

normal analog sounds.

When viewing a programme from the EXT terminal

which has not been set to DIGITAL-IN, or when

viewing a TV broadcasting programme:

When viewing Dolby Surround encoded programmes, you

can enjoy the atmosphere of Dolby Surround Pro Logic

surround sound.

• You can turn this function on or off with a single press. For

details, see “4 3D Button” on page 10.

• For details of how to adjust the surround effect level, adjust

the volume balance of the speakers, and perform the

setting necessary when adding a front speaker system or

subwoofer system, refer to “3D-PHONIC setting” on

page 21.

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL SURROUND

Note:

! Other surround functions

• When a speaker system is not connected to the TV, set TV

SPEAKER to L/C/R and SUBWOOFER to OFF. Otherwise

the sound will not be emitted correctly.

• When you do not want to emit sound from the TV speakers,

set TV SPEAKER to OFF.

DANCE CLUB:

This function creates a dance club atmosphere.

CONCERT HALL:

This function creates a concert hall atmosphere.

DOLBY DIGITAL setting

STADIUM:

This function creates a stadium atmosphere.

Correctly set the items in the sub-menu of the DOLBY

DIGITAL function, and use the test signal to control the

volume level of the speakers so that you can listen to the

sounds from them uniformly. Be sure to perform this

operation before using the DOLBY DIGITAL function.

• The above function does not appear in the DIGITAL

SURROUND menu when viewing a programme from the

EXT terminal which has been set to DIGITAL-IN.

• The above function does not work properly for the Dolby

Surround encoded programmes or mono sound

programmes.

1 Press the 6buttons to choose DOLBY

DIGITAL. Then press the 3button.

The sub-menu of the DOLBY DIGITAL function

appears.

3D-PHONIC setting

1 Press the 6buttons to choose 3D-

PHONIC. Then press the 3button.

The sub-menu of the 3D-PHONIC function appears.

2 Press the 6buttons to choose an item.

Then press the 5buttons to change

the setting.

TV SPEAKER:

Only set to CENTRE when the front speakers are

connected to the TV. Otherwise set to L/C/R.

2 Press the 6buttons to choose an item.

Then press the 5buttons to change

the setting.

REAR SPEAKER:

TV SPEAKER:

Only set to CENTRE when the front speakers are

connected to the TV. Otherwise set to L/C/R.

Set to ON when the rear speaker is connected to the

TV. Otherwise set to OFF. However, you cannot enjoy

surround sound when it is set to OFF.

SUBWOOFER:

Set SUBWOOFER to ON when the subwoofer system

is connected to the TV. Otherwise, set to OFF.

SUBWOOFER:

Set SUBWOOFER to ON when the subwoofer system

is connected to the TV. Otherwise, set to OFF.

LEVEL:

TEST MODE/VOLUME (LEFT/CENTRE/RIGHT/

LS/RS):

Set the volume balance of the speakers so that the

correct surround effect can be achieved.

When the other settings have been completed, adjust in

accordance with “Adjusting the volume balance with the

TEST MODE” on page 22.

You can control the effect level of the 3D-PHONIC

function as you like.

VOLUME (LEFT/CENTRE/RIGHT):

You can adjust the sound level of each speaker

individually. LEFT/RIGHT denotes left and right of the

front speakers and CENTRE denotes the centre

speaker.

3 Press the OK button to complete the

setting.

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL SURROUND

DELAY TIME:

3 Press the 6buttons to adjust the

A delay can be applied to SURROUND (surround

sound) and CENTRE (centre sound) depending on the

arrangement of the speakers.

sound volume of each of the speakers.

Adjust the sound volumes so that you can listen to the

sounds at the same volume when you are sitting where

you would normally sit to watch the TV.

Select DELAY TIME and press the 3button to display

the DELAY TIME menu. The DELAY TIME is changed

in 1ms steps every time the 5buttons are pressed.

LEFT/RIGHT:

The left or right of the front speakers

CENTRE:

The centre speaker

LS/RS:

The left or right of the surround speakers

If REAR SPEAKER is set to OFF, LS and RS are not

displayed.

4 Press the a button to complete the

settings.

3 Press the OK button to complete the

setting.

The menu disappears.

Note:

• When using the front speaker system or subwoofer system

with the TV, it is recommend that this TEST MODE is used

to adjust the speaker volume levels each time the system

is used.

Note:

• When a speaker system is not connected to the TV, set TV

SPEAKER to L/C/R and SUBWOOFER to OFF. Otherwise

the sound will not be emitted correctly.

• When you do not want to emit sound from the TV speakers,

set TV SPEAKER to OFF.

• The CENTRE (centre sound) DELAY TIME cannot be

adjusted when the TV SPEAKER is set to L/C/R.

Adjusting the volume balance with

the TEST MODE

Use the test signal to adjust the volume level of each speaker

so that they are all the same.

Preparation:

• The TV volume cannot be adjusted after the menu is

displayed. Increase to the TV volume level to about 10

before displaying the menu.

1 Display the sub-menu of the DOLBY

DIGITAL function.

2 Press the 6buttons to choose TEST

MODE. Then press the 5buttons to

choose ON.

Test signals are output from each of the speakers in

turn.

When using the front speaker system and/or

subwoofer system with the TV:

Turn on the power of each amplifier, slowly increase the

amplifier’s volumes until the sound emitted from each

speaker connected to the system is about the same as

that of the sound emitted from the TV speakers. Note

that increasing the amplifier volume too high may

damage the speakers.

Stopping the test signal:

Press the 6buttons to choose TEST MODE and

press the 5buttons to choose OFF.

Download from Www.Somanuals.com. All Manuals Search And Download.

EXT SETTING

Note:

• The EXT-1 terminal does not support S-VIDEO

signal (Y/C signal) and you cannot set S-IN (S-

VIDEO input) in the EXT-1 terminal.

• Setting S-IN (S-VIDEO input) changes the head

character from “E” to “S”. For example, “E2” is

changed to “S2”.

• Even an device which enables the S-VIDEO signal

(Y/C signal) to be output may output a regular video

signal (composite signal) depending on the device

setting. If a picture cannot appear because S-IN (S-

VIDEO input) setting has been made, read the

device Instruction Manual carefully again to check

for the device settings.

To display EXT SETTING menu:

1 Press the

button to display MENU

! DIGITAL-IN

(main menu).

When connecting a device (such as DVD player) which

enables Dolby Digital audio signal to be putput, you can listen

to Dolby Digital audio.

2 Press the6 button to choose EXT

SETTING. Then press the

button.

Preparation:

! S-IN (S-VIDEO input)

• In order to listen to Dolby Digital audio, correctly connect a

device to the TV in accordance with “Listening to Dolby

Digital audio” on page 36.

When connecting a device (such as S-VHS VCR) which

enables an S-VIDEO signal (Y/C signal) to be output, you can

enjoy high-quality picture of the S-VIDEO signal (Y/C signal).

• If DIGITAL-IN is set by mistake when no device is

connected to the DIGITAL AUDIO IN terminal, no sound is

emitted.

Preparation:

• At first, read the Device Instruction Manual and

“ADDITIONAL PREPARATION” on page 35 to connect the

device to the TV properly. Second, follow the Device

Instruction Manual to set the device so that a S-VIDEO

signal (Y/C signal) can be output to the TV.

• Do not set S-IN (S-VIDEO input) to the EXT terminal

connected to a device which cannot output a S-VIDEO (Y/

C signal). If it is set wrongly, a picture cannot appear.

1 Press the 6buttons or 5buttons to

choose an EXT terminal.

2 Press the green button to set the

DIGITAL-IN.

Pressing the green button repeatedly until the mark

which is the same as the type of cable connected to the

DIGITAL AUDIO IN terminal is selected.

1 Press the

buttons or

buttons to

: Select this mark when connected with coaxial

cable.

choose an EXT terminal.

2 Press the yellow button and set the S-IN

(S-VIDEO input).

: Select this mark when connected with optical

cable.

A y(S-VIDEO input) mark is displayed. You can

view an S-VIDEO signal (Y/C signal) instead of the

regular video signal (composite signal).

To cancel the DIGITAL-IN setting:

Press the green button to turn off the mark of DIGITAL-

IN.

To cancel the S-IN (S-VIDEO input) setting:

Press the yellow button and turn off y(S-VIDEO

input) mark. The regular video signal (composite signal)

pictures are resumed.

3 Press the a button to complete the

setting.

The menu disappears.

Note:

3 Press the

setting.

button to complete the

• DIGITAL-IN cannot be set for the TV and EXT-4

terminal.

• This TV does not work with digital audio signals

other than Dolby Digital audio. If no sound is

emitted from the speakers, cancel the DIGITAL-IN

setting and change to normal analog sounds.

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

EXT SETTING

! ID LIST

! DUBBING

You can have a name corresponding to the devices

connected for each EXT terminal. Giving a name to an EXT

terminal makes the EXT terminal number appear on the

screen, together with the name.

You can choose a signal source to be output from an EXT-2

terminal.

You can choose any one of the output signal of the device

connected to the EXT terminal and the picture and sound

from a TV channel you are currently viewing to output it to the

EXT-2 terminal.

1 Press the6 buttons or5 buttons to

choose an EXT terminal.

1 Press the 5 buttons to choose the

arrow from the menu.

2 Press the blue button to display the name

list (ID LIST).

2 Press the 6buttons to choose an EXT

3 Press the6buttons to choose a name.

terminal or TV.

Then press the

button.

The arrow in the menu represents a signal flow. The left

side of the arrow denotes a signal source output from

the EXT-2 terminal.

The ID LIST disappears and the name is assigned to

the EXT terminal.

EXT-1/EXT-3/EXT-4:

To erase a name assigned to the EXT

terminal:

Choose a blank space.

The output signal of the device connected to an EXT

terminal passes through the TV and is output from the

EXT-2 terminal.

4 Press the

setting.

button to complete the

TV:

The picture and sound of the TV channel you are

currently viewing are output from the EXT-2 terminal.

The menu disappears.

Note:

3 Press the

setting.

button to complete the

• You cannot assign an EXT terminal name not found

in the name list (ID LIST).

The menu disappears.

Note:

• During dubbing, you cannot turn off the TV. Turning

off the TV also turns off the output from the EXT-2

terminal.

• When you choose an EXT terminal as an output,

you can view a TV programme or a picture from the

other EXT terminal while dubbing the picture from a

device connected to the EXT terminal onto a VCR

connected to the EXT-2 terminal.

• The RGB signals from the TV games cannot be

output.Teletext programmes cannot be output.

• The sound from the EXT terminal set to DIGITAL-IN

is not output from the EXT-2 terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

! BLUE BACK

You can set the TV to automatically change to a blue screen

and mute the sound if the signal is weak or absent, or when

there is no input from an external device.

1 Press the

BACK.

buttons to choose BLUE

2 Press the5 buttons to choose ON.

To display the FEATURES menu:

To cancel the BLUE BACK function:

Press the5 buttons to choose OFF.

1 Press the

button to display MENU

(main menu).

3 Press the

setting.

button to complete the

2 Press the6 button to choose

FEATURES. Then press the

button.

The menu disappears.

! CHILD LOCK

! SLEEP TIMER

When there is a TV channel you wish your children not to

watch, you can use the CHILD LOCK function to lock out the

TV channel. Even when a child chooses a Programme

number (PR) in which a locked TV channel has been

You can set the TV to automatically turn off after a specified

period of time.

registered, the screen will change to blue and displays

1 Press the

buttons to choose SLEEP

(CHILD LOCK) so the TV channel cannot be viewed. Unless

you enter a pre-set ID number by a special operation, the lock

cannot be released and the child cannot view the TV channel

programmes.

TIMER. Then press the

button.

A Sub-menu of the SLEEP TIMER function appears.

To set the CHILD LOCK function

1 Press the6 buttons to choose CHILD

LOCK. Then press the

“SET ID NO.” (ID number setting screen) appears.

button.

2 Press the

of time.

buttons to set the period

You can set the period of time a maximum of 120

minutes (2 hours) in 10 minute increments.

To cancel the SLEEP TIMER function:

Press the button to set a period of time to “OFF.”

2 Set the ID number to your liking.

3 Press the

settings.

button to complete the

1 Press the6 buttons to choose a

number.

The menu disappears.

Note:

2 Press the5 buttons to move the

• One minute before the SLEEP TIMER function

turns off the TV, “GOOD NIGHT!” appears.

• The SLEEP TIMER function cannot be used to turn

off the TV’s main power.

• When the SLEEP TIMER function is on, you can

display the Sub-menu of the SLEEP TIMER

function again to confirm and/or change the

remaining period of time of the SLEEP TIMER

cursor.

3 Press the

button.

The Sub-menu of CHILD LOCK appears.

function. Press the

confirming and / or changing the remaining time.

button to exit the menu after

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

Note:

4 Press the6 buttons to choose a TV

• Even if you reset the lock temporarily, it does not

mean that the CHILD LOCK function set for the TV

channel is cancelled. The next time anyone

attempts to view the TV channel, it will be locked

again.

• When you would like to cancel the CHILD LOCK

function, you must perform the operation “To set the

CHILD LOCK function” again.

channel.

Every time you press the6 buttons, the Programme

number (PR) changes, and the picture of the TV

channel registered in the Programme number (PR) is

displayed on the screen.

5 Press the blue button and set the CHILD

LOCK function.

• To disable easy choosing of a Programme number

(PR) in which a locked TV channel has been

registered, the Programme number (PR) has been

(CHILD LOCK) appears and the TV channel is locked.

To reset the CHILD LOCK function:

Press the blue button again.

set that it cannot be chosen by the

buttons or

the operation buttons at the TV.

• To disable easy resetting of the lock, “ID NO.” (ID

NO. input screen) is set so that it cannot appear

(CHILD LOCK) disappears.

6 Press the

setting.

button to complete the

unless you press the

(Information) button.

The menu disappears.

! DECODER (EXT-2)

Note:

Only when connecting a Decoder with a T-V LINK compatible

VCR connected to the EXT-2 terminal, you can use this

function. To operate this function, see “Using the DECODER

(EXT-2) function” on page 34.

• To disable easy resetting of the CHILD LOCK

function, the menu disappears by choosing the

CHILD LOCK function and pressing the

as in the ordinary menu operation.

button

Caution:

To view a locked TV channel

• If you have not connected a Decoder with a T-V LINK

compatible VCR connected to the EXT-2 terminal, setting

this function to “ON” by mistake causes the picture/sound

of a TV channel you are currently viewing not to be issued.

1 Choose a Programme number (PR) in

which a TV channel locked with the

Number buttons or PR LIST.

The screen changes to blue and the (CHILD LOCK)

appears. You cannot view the TV channel.

2 Press the

(Information) button to

display “ID NO.” (ID NO. input screen).

3 Press the Number buttons to enter the ID

number.

The lock is temporarily released so you can view the TV

channel.

If you have forgotten the ID number:

Perform step 1 of “To set the CHILD LOCK function”.

After confirming the ID number, press the

exit the menu.

button to

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

! AUTO PROGRAM

You can automatically register the TV channels which can be

received well at your residence in the TV’s Programme

numbers (PR) by performing the following.

1 Press the

buttons to choose AUTO

PROGRAM. Then press the

The COUNTRY menu appears as a sub-menu of the

AUTO PROGRAM function.

button.

To display the INSTALL menu:

There are two COUNTRY menus. Pressing the yellow

button changes the COUNTRY menu as follows:

1 Press the a button to display MENU

(main menu).

2 Press the

button to choose the

INSTALL menu. Then press the

button.

! LANGUAGE

2 Press the

and

buttons to

You can choose the language you want to use for the on-

screen display from the language list in a menu.

choose the country where you are now

located.

1 Press the

buttons to choose

3 Press the blue button to start the AUTO

PROGRAM function.

LANGUAGE. Then press the

button.

A sub-menu of the LANGUAGE function appears.

The AUTO PROGRAM menu appears and received TV

channels are automatically registered in the

Programme numbers (PR).

2 Press the

and

buttons to

If “ACI START/ACI SKIP” appears in the AUTO

PROGRAM menu:

choose a language.

You can use the ACI (Automatic Channel Installation)

function to decode the ACI data and complete the

registration of all the TV channels in a short period of

time. For details of the ACI function and how to use it,

refer to “Using the ACI function” on page 33.

If you don’t want to use the ACI function, press the 6

3 Press the

setting.

button to complete the

The menu disappears.

buttons to choose ACI SKIP and then press

To cancel the AUTO PROGRAM function:

Press the

button.

4 After the TV channels have been

registered in the Programme numbers

(PR), the EDIT menu appears.

You can proceed to edit the Programme numbers (PR)

using the EDIT/MANUAL function. For details, see

“EDIT/MANUAL” on page 28.

When not using the EDIT/MANUAL function:

If you do not need to use the EDIT/MANUAL function,

go to the next step.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

5 Press the

button to display the T-V

! EDIT/MANUAL

LINK menu.

The EDIT/MANUAL functions are divided into two types:

editing of the current Programme numbers (PR) (EDIT

functions) and manual registration of a TV channel you want

to view to the Programme number (PR) (MANUAL function).

The details about these functions are as follows:

MOVE:

This function changes a Programme number (PR) of a TV

channel.

ID:

This function registers a Channel name (ID) to a TV channel.

6 Operate the T-V LINK menu according to

the type of VCR connected to the EXT-2

terminal.

INSERT:

This function adds a new TV channel in the current

Programme numbers (PR) list by using the CH/CC number.

When a T-V LINK compatible VCR is not

connected:

DELETE:

This function deletes a unnecessary TV channel.

Press the

button to exit the T-V LINK menu.

The T-V LINK menu disappears, and all the settings are

completed.

MANUAL:

This function manually registers a new TV channel in a

Programme number (PR).

When a T-V LINK compatible VCR is

connected:

Follow the operating procedure “Downloading the data

to VCR” on page 33 to transmit the Programme number

(PR) data to the VCR.

Caution:

• Using the MOVE, DELETE or INSERT function rewrites the

current Programme numbers (PR) list. Resultingly, the

Programme number (PR) of some of the TV channels will

change.

Note:

• When your TV can detect the TV channel name

from the TV channel broadcast signal, it

automatically registers the TV channel name (ID) to

the Programme number (PR) in which the TV

channel has been registered.

• If a TV channel you want to view is not set to a

Programme number (PR), manually set it using the

MANUAL function. For details, see “EDIT/

MANUAL” on page 28.

• The TV channel is not registered in Programme

number PR 0 (AV). When you want to register a TV

channel to PR 0 (AV) manually set it using the

MANUAL function. For details, see “EDIT/

MANUAL” on page 28.

• Using the MANUAL function for a TV channel for which the

CHILD LOCK function has been set cancels the CHILD

LOCK function for the TV channel.

• Using the MANUAL function for a TV channel for which the

DECODER (EXT-2) function has been set to ON returns

the setting of the DECODER (EXT-2) function for the TV

channel to OFF.

• When a TV channel has already been registered in PR 99,

using the INSERT function deletes the TV channel.

Note:

• For Programme number PR 0, “AV” appears in the

Programme numbers (PR) list.

• An EXT terminal number does not appear in the

Programme numbers (PR) list.

• The CH/CC number is a number unique to the TV and

corresponding to the Channel number of a TV channel. For

the relationship of a Channel number and a CH/CC

number, see “CH/CC NUMBER” on page 39.

• You cannot use the INSERT function if you do not know a

Channel number of a TV channel. Use the MANUAL

function to register a TV channel in the Programme number

(PR).

1 Press the

buttons to choose EDIT/

MANUAL. Then press the

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

2 Follow the operation description of a

function you want to use and operate the

function.

4 Press the button to change the

Programme number (PR) of a TV channel

to a new Programme number (PR).

3 Press the

settings.

button to complete the

The T-V LINK menu appears.

1 Press the

channel.

buttons to choose a TV

Every time you press the

buttons, the Programme

number (PR) is changed over, and the picture of the TV

channel registered in the Programme number (PR)

appears on the screen.

2 Press the red button to start the ID

function.

4 Operate the T-V LINK menu according to

the type of VCR connected to the EXT-2

terminal.

When a T-V LINK compatible VCR is not

connected:

Press the

button to exit the T-V LINK menu.

The T-V LINK menu disappears and all the settings are

completed.

When a T-V LINK compatible VCR is

connected:

Follow the operating procedure “Downloading the data

to VCR” on page 33 to transmit the Programme number

(PR) data to the VCR.

3 Press the

buttons to choose the first

character of a Channel name (ID) you

want to attach to the TV channel.

MOVE

1 Press the

channel.

buttons to choose a TV

Every time you press the

buttons, the Programme

number (PR) is changed over, and the picture of the TV

channel registered in the Programme number (PR)

appears on the screen.

2 Press the button to start the MOVE

function.

3 Press the

buttons to choose a new

Programme number (PR).

To cancel the MOVE function:

Press the

(Information) button.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

4 Press the blue button to display the ID

LIST (channel name list).

INSERT

Preparation:

• A CH/CC number unique to this TV and corresponding to

the Channel number of a TV channel is required. Find the

corresponding CH/CC number from a table “CH/CC

NUMBER” on page 39 based on the Channel number of

the TV channel.

• When the COUNTRY setting is not FRANCE, use a two-

digit CH/CC number. When the COUNTRY setting is

FRANCE, use a three-digit CH/CC number.

• Only when you add a TV channel (SECAM-L system) from

a French station, be sure to set COUNTRY to FRANCE. If

the COUNTRY setting is not FRANCE, follow the

description “Changing the COUNTRY setting” on page 33

to change the COUNTRY setting to FRANCE, then start

the INSERT function.

5 Press the

buttons to choose the

Channel name (ID).

1 Press the

buttons to choose a

To cancel the ID function:

Programme number (PR) for which you

will register a new TV channel.

Press the

(Information) button.

6 Press the

button to register a

2 Press the green button and start the

INSERT function.

Channel name (ID) to a TV channel.

Note:

• You can register your unique Channel name (ID) to

the TV channel. When step 3 is completed, do not

go to step 4, but press the

buttons to move the

cursor and the

buttons to choose a character

for completing the Channel name (ID). Then press

the button to register the Channel name (ID) to

the TV channel.

3 Press the

buttons to choose “CC” or

“CH” according to the CH/CC number of

the TV channel.

When the COUNTRY setting is FRANCE:

Choose “CH1”, “CH2”, “CC1” or “CC2”.

To cancel the INSERT function:

Press the

(Information) button.

4 Press the Number buttons to enter the

remaining CH/CC number.

The TV shifts to registration mode.

When the registration is completed, the picture of the

TV channel appears on the screen.

Note:

• The CH/CC number is a number indicating the

broadcast frequency to the TV. If the TV cannot

detect the TV channel corresponding to the

broadcast frequency indicated by the CH/CC

number, a picture in the no-signal state appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

4 Press the green or red button to search

for a TV channel.

DELETE

1 Press the 6buttons to choose a TV

Scanning stops when the TV finds a TV channel. Then

the TV channel is displayed.

channel.

Every time you press the 6buttons, the Programme

number (PR) is changed over, and the picture of the TV

channel registered in the Programme number (PR)

appears on the screen.

5 Press the green or red button repeatedly

until the TV channel you want appears.

If the TV channel reception is poor:

Press the blue or yellow button to fine-tune the TV

channel.

2 Press the yellow button to delete the TV

channel.

If you cannot hear the normal sound even

when the picture of the TV channel appears

normally:

The TV channel is deleted from the Programme

numbers (PR) list.

The SYSTEM setting is wrong. Press the button and

MANUAL

choose a SYSTEM that has normal sound.

Preparation:

6 Press the

button and register the TV

• As long as you register the TV channel (SECAM-L system)

from a French station, be sure to set the COUNTRY setting

to FRANCE. If the COUNTRY setting is not FRANCE,

follow the description “Changing the COUNTRY setting” on

page 33 to change the COUNTRY setting to FRANCE,

then start the MANUAL function.

channel to a Programme number (PR).

The normal EDIT menu is resumed.

1 Press the

buttons to choose a

Programme number (PR) to which you

want to register a new TV channel.

2 Press the blue button to activate the

MANUAL function.

At the right side following the CH/CC number, the

SYSTEM (broadcasting system) of the TV channel

appears.

To cancel the MANUAL function:

Press the

(Information) button.

3 Press the button to choose the

SYSTEM (broadcasting system) for a TV

channel you want to register.

TV channel (SECAM-L system) from a French

station:

Set the SYSTEM to “L”. If it is set to one other than “L”,

you cannot receive the TV channel of the SECAM-L

system.

Other TV channels:

If you do not know the correct broadcasting system, set

the SYSTEM to “B/G”. If “B/G” is not correct, it results in

the fact that you will not hear the sound normally when

the TV detects a TV channel. In this case, retry to set

the SYSTEM again correctly so that no problem arises.

Download from Www.Somanuals.com. All Manuals Search And Download.

DEMO

To display the DEMO menu:

1 Press the

button to display MENU

(main menu).

2 Press the 6 button to choose

DEMO. Then press the button.

The DEMO function automatically demonstrates some of the

TV functions.

1 Press the 6 buttons to choose ON.

2 Press the

settings.

button to complete the

The DEMO function is set to ON, and the demonstration

will start.

To stop the demonstration:

Press one of the buttons on the remote control.

When the DEMO function is set to ON:

Each time the TV is turned on, the demonstration starts

automatically. If you do not want that to happen,

perform the following operations to cancel the DEMO

function:

1 Display the DEMO menu again.

2 Press the 6 buttons to choose OFF.

3 Press the

button to cancel the

DEMO function.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL MENU OPERATIONS

! Using the ACI function

! Downloading the data to VCR

This TV has an ACI function which decodes the ACI

(automatic Channel Installation) data.

You can transmit to the latest Programme numbers (PR) data

to the VCR with the T-V LINK function.

Using the ACI function allows all TV channels transmitted

from the cable TV station to be properly registered quickly

according to the data from the cable TV station.

Caution:

• Only when the T-V LINK compatible VCR is connected to

the EXT-2 terminal, this operation is enabled.

• Only when the T-V LINK menu is being displayed, this

operation is enabled.

Caution:

• If your cable TV station broadcasts ACI data and if “ACI

START/ACI SKIP” appears in the AUTO PROGRAM

menu, the ACI function is enabled. In all other cases, it is

disabled.

1 Press the 6button to choose ACI

START. Then press the

start the ACI function.

button to

When you don't want to use the ACI function:

Press the 6button to choose ACI SKIP and then

1 Turn on the VCR.

press the

button.

2 Press the

button.

The data transmission begins.

If the AUTO PROGRAM menu changes to

another menu:

Depending on your cable TV station, there may be a

broadcast selection menu set up by the cable TV

station.

Follow the menu indications and use the 5and 6

buttons to operate the menu. After you have made the

The T-V LINK menu disappears once the data

transmission ends.

setting, press the

button.

When the T-V LINK menu is changed over to

another menu:

The menu operation at the TV side is completed and it

is shifted to the menu operation at the VCR side. Refer

to the VCR Instruction Manual and operate the VCR.

If “ACI ERROR” is displayed in the AUTO

PROGRAM menu:

“ACI ERROR” denotes that the ACI function is not

working properly. Press the

button to start the ACI

function again.

If “ACI ERROR” still appears even after you have tried

to start the ACI function several times, press the

button to start the AUTO PROGRAM function. It does

not cause any problem because all the TV channels are

registered to the Programme numbers (PR) by the

AUTO PROGRAM function.

Note:

• If “FEATURE NOT AVAILABLE” appears at the T-V

LINK menu, ensure the following three items are

correct; then press the

transmission.

- Has the T-V LINK compatible VCR been

connected to the EXT-2 terminal?

button to retry data

2 When the settings are completed, the

EDIT menu is displayed. Return to the

instructions that you were reading

before, and continue the operation.

- Has the VCR power been turned on?

- Does the SCART cable that is connected to the

EXT-2 terminal to T-V LINK compatible VCR

have all proper connections?

When the “Initial Settings” has been made:

! Changing the COUNTRY

Return to step 6 of “Initial Settings” on page 4.

When the “AUTO PROGRAM” has been made:

Return to step 4 of “AUTO PROGRAM” on page 27.

setting

After the AUTO PROGRAM function is completed, you can

change the country you have already set by using the AUTO

PROGRAM function.

When registering the TV channels for French broadcast

stations (SECAM-L system), perform this operation to change

the country.

Note:

• If you have any questions about the items in the

Broadcast Selection menu or how to operate the

menu, please contact your cable TV station.

• When the cable TV broadcast reception is poor, the

ACI function will not work properly.

• If there is an error in the ACI data itself, the TV

channel cannot be registered properly. If this

happens, turn the ACI function off (ACI SKIP) and

use the AUTO PROGRAM function. Alternatively,

use the EDIT/MANUAL function to correct the

Programme number (PR) setting.

1 Display the INSTALL menu.

When the EDIT menu is currently being

displayed:

Press the

menu.

(Information) to return to the INSTALL

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL MENU OPERATIONS

2 Press the 6 buttons to choose AUTO

6 Press the

setting.

button to complete the

PROGRAM. Then press the

button.

The T-V LINK menu appears.

A COUNTRY menu appears as a sub-menu of the

AUTO PROGRAM function.

There are two COUNTRY menus. Pressing the yellow

button changes the COUNTRY as follows:

7 Follow the operating procedure

“Downloading the data to VCR” on

page 33 to transmit the Programme

number (PR) data to the VCR.

3 Press the

and the 6 buttons to

choose a country.

4 Press the

setting.

button to complete the

8 If you have another TV channel capable

of being unscrambled with a Decoder,

repeat steps 2 through 7.

The menu disappears.

To return to the INSTALL menu from the

COUNTRY menu:

Note:

Press the

button.

(Information) button instead of the

• If for some reason the DECODER (EXT-2) function

has been set to “ON” but the TV channel cannot be

unscrambled, check the following:

- Has the Decoder been connected to the VCR

properly according to the VCR and Decoder

Instruction Manuals?

! Using the DECODER (EXT-2)

function

- Has the Decoder power been turned on?

- Can the TV channel be unscrambled with a

Decoder?

When connecting a Decoder with a T-V LINK compatible

VCR connected to the EXT-2 terminal, use the DECODER

(EXT-2) function to unscramble the scrambled TV channels.

- Is it necessary to change the VCR settings in

order to connect the Decoder? Confirm that the

VCR is set properly by rechecking the VCR

Instruction Manual.

1 Turn on the Decoder power.

2 Display the TV channel capable of being

unscrambled with the Decoder on the TV.

Even if the Decoder is functioning, a scrambled picture

appears at this time.

3 Press the

MENU.

button to display the

The MENU (main menu) appears.

4 Press the

buttons to choose

FEATURES. Then press the

The FEATURES menu appears.

button.

5 Press the

buttons to choose

DECODER (EXT-2). Then press the

buttons to choose ON.

An unscrambled picture appears.

To cancel the DECODER (EXT-2) function:

Press the

buttons to choose OFF.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL PREPARATION

! Connecting the external devices

Connect the devices to the TV, paying attention to the

following connection diagram.

Before connecting anything:

Behind the Cover

• Read the manuals provided with the devices. Depending

on the devices, the connection method may differ from the

figure. In addition, the device settings may be changed

depending on the connection method to secure proper

operation.

• Turn off all the devices including the TV.

• The “SPECIFICATIONS” on page 43 contains the details

of the EXT terminals. If you are connecting a device not

listed in the following connection diagram, see the table to

choose the best EXT terminal.

• Note that connecting cables are not supplied.

1 VCR (composite signal)

2 VCR (composite signal/S-VIDEO signal)

3 T-V LINK compatible VCR (composite signal/

S-VIDEO signal)

4 Decoder

5 DVD player (composite signal/S-VIDEO signal)

6 DVD player (composite signal/RGB signal)

7 TV game (composite signal/RGB signal)

8 TV game (composite signal/S-VIDEO signal)

9 Headphones

0 Camcorder (composite signal/S-VIDEO signal)

- SCART cable

= Audio cable

~ Video cable

! S-VIDEO cable

Back of the TV

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL PREPARATION

Devices which can output the S-

VIDEO signal (Y/C signal) such as a S-

VHS VCR

! Listening to Dolby Digital

audio

In order to listen to Dolby Digital audio which is recorded as a

Dolby Digital programme source (such as a DVD-video disc),

connect the device and set the DIGITAL-IN as described

below.

Connect the device to an EXT terminal other than the EXT-1

terminal.

You can choose a video input signal from the S-VIDEO signal

(Y/C signal) and regular video signal (composite signal). For

details of how to operate the device, see “S-IN (S-VIDEO

input)” on page 23.

Preparation:

• A device (such as DVD player) with a digital output terminal

(coaxial or optical) for Dolby Digital is necessary.

• A coaxial cable or optical cable is necessary to make the

connections. (Not supplied with the TV)

T-V LINK compatible VCR

Be sure to connect the T-V LINK compatible VCR to the

EXT-2 terminal. If not, the T-V LINK function will not work

properly.

• In accordance with the instruction manual which is supplied

with the device, correctly connect a coaxial cable or optical

cable to the device’s DIGITAL OUT (digital output) terminal

and set the device so that the Dolby Digital audio signal is

output.

• Correctly connect the device to the EXT terminal in

accordance with “Connecting the external devices” on

page 35. However, since the EXT-4 terminal does not work

with Dolby Digital audio, it cannot be used.

Note:

• When connecting a T-V LINK compatible VCR to the EXT-

2 terminal, be sure to connect the Decoder to the VCR. If

not, the T-V LINK function may not work properly. After you

have registered TV channels to the Programme numbers

(PR), set the DECODER (EXT-2) function for the

Programme number (PR) to ON in order to unscramble a

scrambled TV channel. For details of operation, see “Using

the DECODER (EXT-2) function” on page 34.

1 Connect the device to the DIGITAL

AUDIO IN terminal with a coaxial cable 1

or optical cable 2.

Connecting headphones

Connect the headphones with a stereo mini-jack (of 3.5 mm

in diameter) to the headphone jack at the TV front panel.

Video/sound signal output from the

EXT-2 terminal

You can arbitrarily change over the output of the video/sound

signal from the EXT-2 terminal. It is useful when you want to

dub the video/sound from another device on the VCR

connected to the EXT-2 terminal. For details on how to do this

operation, see “DUBBING” on page 24.

Back of the TV

2 Connect the device and set the EXT

terminal to DIGITAL-IN in accordance

with “DIGITAL-IN” on page 23.

This completes the preparation.

TV output from the EXT-1 terminal

The output of video/sound signal of a TV channel you are

currently viewing is always output from the EXT-1 terminal.

Note:

• When an optical input and coaxial input are input

simultaneously, the optical input takes precedence.

• When the headphones are used, the sound

becomes normal stereo.

• This TV does not work with digital audio signals

other than Dolby Digital audio. If no sound is

emitted from the speakers, cancel the DIGITAL-IN

setting and change to normal analog sound.

• The sound from the EXT terminal set to DIGITAL-IN

is not output from the EXT-2 terminal.

• Changing over a Programme number (PR) also changes

over the TV output from the EXT-1 terminal.

• The video/sound signal from an EXT terminal cannot be

output.

• Teletext programmes cannot be output.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL PREPARATION

! Using additional audio

equipments

After correctly connecting audio equipments to the TV, use

the TV menu to correctly set the functions of the audio

equipments.

1 Connect the audio equipments to the TV.

Before connecting anything:

• Read the manuals that came with the audio

equipment.

• Do not turn the power of the TV or audio equipments

on until the connections have been completed.

• If the additional speakers are placed immediately next

to the TV, use magnetic-shielded speakers in order to

prevent magnetism from the speakers adversely

effecting the TV.

Note:

• Connecting cables are not supplied.

• The audio signal output from the AUDIO OUT

terminal cannot be stopped. When you want to stop

the sound from being emitted from the additional

speaker systems, turn the amplifier’s power off.

Surround speakers 1:

Connect surround speakers to the TV when you want to

use the DOLBY DIGITAL function to enjoy surround

sound.

Back of the TV

• Even without surround speakers, you can easily enjoy

surround sound by using the 3D-PHONIC function.

• Use impedance 8-ohm type.

• Pay attention to the positive (+) and negative (-)

polarities when connecting surround speakers to your

TV.

• For the best effect, position the surround speakers at

least 1 metre above the heads of seated viewers.

Front speaker system

(Front L/R speakers 2 and amplifier 3):

You can use your hi-fi audio system speakers instead of

the TV speakers.

Subwoofer system

(Subwoofer and amplifier 5):

Using the subwoofer system improves the playing

performance of the low sounds.

• It is particularly effective with the low frequency effects

(LFE) included in 5.1-channel Dolby Digital surround

sound.

Approx.

45 degrees

Positioning of speakers

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL PREPARATION

Do you use the surround speakers?

2 Set the following functions (A to D)

correctly depending on the speakers you

want to use.

Yes

A: SPEAKER function

Stop the sound from being emitted from the TV

speakers.

OFF

Correctly perform the settings in accordance with

“SPEAKER” on page 18.

Note:

• By using the 5buttons on the TV remote control

or the buttons on the TV, the volume of all the

speakers including those of the additional audio

equipments can be adjusted simultaneously.

• If the volume of the TV speakers is different to the

volume of the front speaker system or subwoofer

system, adjust the volumes of each amplifier’s to

match that of the TV speakers.

B: TV SPEAKER function

When using the 3D-PHONIC function or DOLBY

DIGITAL function, all the TV speakers work as centre

speakers.

Correctly perform the settings in accordance with “3D-

PHONIC setting” on page 21 and “DOLBY DIGITAL

setting” on page 21.

• Note that the function explained here is different to the

TV SPEAKER function in the HEADPHONE menu.

• When the TV SPEAKER function in either one of the

3D-PHONIC menu or DOLBY DIGITAL menu is set,

the other is automatically set.

C: SUBWOOFER function

When using the 3D-PHONIC function or the DOLBY

DIGITAL function, the SUBWOOFER function makes

the low freaqueney effects (LFE) included in 5.1-

channel Dolby Digital surround sound more effective.

Correctly perform the settings in accordance with

“SUBWOOFER” on page 19, “3D-PHONIC setting” on

page 21 and “DOLBY DIGITAL setting” on page 21.

• When the SUBWOOFER function in any one of the

SOUND SETTING menu, 3D-PHONIC menu or

DOLBY DIGITAL menu is set, the others are

automatically set.

D: REAR SPEAKER function

When the DOLBY DIGITAL function is used Dolby

Digital programme surround sound is emitted from the

surround speakers.

Correctly perform the settings in accordance with

“DOLBY DIGITAL setting” on page 21.

• Note that you cannot use the DOLBY DIGITAL

function to enjoy surround sound if the REAR

SPEAKER function is turned OFF.

Do you use the front speaker system?

Yes

OFF

CENTRE

L/C/R

• In cases where you do not want to emit sound from the

TV speakers set B (TV SPEAKER) to OFF.

Do you use the subwoofer system?

Yes

OFF

Download from Www.Somanuals.com. All Manuals Search And Download.

CH/CC NUMBER

When you want to use the INSERT function on page 30, find the CH/CC number corresponding to the Channel number of the

TV channel from this table.

Channel

E2, R1

Channel

E40, R40

E41, R41

E42, R42

E43, R43

E44, R44

E45, R45

E46, R46

E47, R47

E48, R48

E49, R49

E50, R50

E51, R51

E52, R52

E53, R53

E54, R54

E55, R55

E56, R56

E57, R57

E58, R58

E59, R59

E60, R60

E61, R61

E62, R62

E63, R63

E64, R64

E65, R65

E66, R66

E67, R67

E68, R68

E69, R69

Channel

S31

CH 02 / CH 202

CH 03 / CH 203

CH 04 / CH 204

CH 05 / CH 205

CH 06 / CH 206

CH 07 / CH 207

CH 08 / CH 208

CH 09 / CH 209

CH 10 / CH 210

CH 11 / CH 211

CH 12 / CH 212

CH 21 / CH 221

CH 22 / CH 222

CH 23 / CH 223

CH 24 / CH 224

CH 25 / CH 225

CH 26 / CH 226

CH 27 / CH 227

CH 28 / CH 228

CH 29 / CH 229

CH 30 / CH 230

CH 31 / CH 231

CH 32 / CH 232

CH 33 / CH 233

CH 34 / CH 234

CH 35 / CH 235

CH 36 / CH 236

CH 37 / CH 237

CH 38 / CH 238

CH 39 / CH 239

CH 40 / CH 240

CH 41 / CH 241

CH 42 / CH 242

CH 43 / CH 243

CH 44 / CH 244

CH 45 / CH 245

CH 46 / CH 246

CH 47 / CH 247

CH 48 / CH 248

CH 49 / CH 249

CH 50 / CH 250

CH 51 / CH 251

CH 52 / CH 252

CH 53 / CH 253

CH 54 / CH 254

CH 55 / CH 255

CH 56 / CH 256

CH 57 / CH 257

CH 58 / CH 258

CH 59 / CH 259

CH 60 / CH 260

CH 61 / CH 261

CH 62 / CH 262

CH 63 / CH 263

CH 64 / CH 264

CH 65 / CH 265

CH 66 / CH 266

CH 67 / CH 267

CH 68 / CH 268

CH 69 / CH 269

CC 01 / CC 201

CC 02 / CC 202

CC 03 / CC 203

CC 04 / CC 204

CC 05 / CC 205

CC 06 / CC 206

CC 07 / CC 207

CC 08 / CC 208

CC 09 / CC 209

CC 10 / CC 210

CC 11 / CC 211

CC 12 / CC 212

CC 13 / CC 213

CC 14 / CC 214

CC 15 / CC 215

CC 16 / CC 216

CC 17 / CC 217

CC 18 / CC 218

CC 19 / CC 219

CC 20 / CC 220

CC 21 / CC 221

CC 22 / CC 222

CC 23 / CC 223

CC 24 / CC 224

CC 25 / CC 225

CC 26 / CC 226

CC 27 / CC 227

CC 28 / CC 228

CC 29 / CC 229

CC 30 / CC 230

CC 31 / CC 231

CC 32 / CC 232

CC 33 / CC 233

CC 34 / CC 234

CC 35 / CC 235

CC 36 / CC 236

CC 37 / CC 237

CC 38 / CC 238

CC 39 / CC 239

CC 40 / CC 240

CC 41 / CC 241

CC 75 / CC 275

CC 76 / CC 276

CC 77 / CC 277

CC 78 / CC 278

CC 79 / CC 279

E3, ITALY A

E4, ITALY B, R2

E5, ITALY D, R6

E6, ITALY E, R7

E7, ITALY F, R8

E8, R9

S32

S33

S34

S35

S36

S37

E9, ITALY G

E10, ITALY H, R10

E11, ITALY H+1, R11

E12, ITALY H+2, R12

E21, R21

S38

S39

S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S40

S41

E22, R22

Y, R3

Z, ITALY C, R4

Z+1, R5

Z+2

E23, R23

E24, R24

E25, R25

E26, R26

E27, R27

E28, R28

E29, R29

E30, R30

E31, R31

E32, R32

E33, R33

E34, R34

E35, R35

E36, R36

E37, R37

E38, R38

E39, R39

Channel

F41

F42

F43

F44

F45

F46

F47

F48

F49

F50

F51

F52

F53

F54

F55

F56

F57

F58

F59

F60

F61

F62

F63

F64

F65

F66

F67

F68

F69

Frequency (MHz)

116 - 124

124 - 132

132 - 140

140 - 148

148 - 156

156 - 164

164 - 172

220 - 228

228 - 236

236 - 244

244 - 252

252 - 260

260 - 268

268 - 276

276 - 284

284 - 292

292 - 300

300 - 306

306 - 311

311 - 319

319 - 327

327 - 335

335 - 343

343 - 351

351 - 359

359 - 367

367 - 375

375 - 383

383 - 391

Frequency (MHz)

391 - 399

399 - 407

407 - 415

415 - 423

423 - 431

431 - 439

439 - 447

447 - 455

455 - 463

463 - 469

CH 102

CH 103

CH 104

CH 105

CH 106

CH 107

CH 108

CH 109

CH 110

CH 121

CH 122

CH 123

CH 124

CH 125

CH 126

CH 127

CH 128

CH 129

CH 130

CH 131

CH 132

CH 133

CH 134

CH 135

CH 136

CH 137

CH 138

CH 139

CH 140

CH 141

CH 142

CH 143

CH 144

CH 145

CH 146

CH 147

CH 148

CH 149

CH 150

CH 151

CH 152

CH 153

CH 154

CH 155

CH 156

CH 157

CH 158

CH 159

CH 160

CH 161

CH 162

CH 163

CH 164

CH 165

CH 166

CH 167

CH 168

CH 169

CC 110

CC 111

CC 112

CC 113

CC 114

CC 115

CC 116

CC 123

CC 124

CC 125

CC 126

CC 127

CC 128

CC 129

CC 130

CC 131

CC 132

CC 133

CC 141

CC 142

CC 143

CC 144

CC 145

CC 146

CC 147

CC 148

CC 149

CC 150

CC 151

CC 152

CC 153

CC 154

CC 155

CC 156

CC 157

CC 158

CC 159

CC 160

CC 161

F10

F21

F22

F23

F24

F25

F26

F27

F28

F29

F30

F31

F32

F33

F34

F35

F36

F37

F38

F39

F40

Note:

• When two CH/CC numbers correspond to one Channel number, choose either one according to the current COUNTRY

setting. When the COUNTRY setting is other than FRANCE, choose a two-digit CH/CC number. When the COUNTRY setting

is FRANCE, choose a three-digit CH/CC number.

• Find the CH/CC number (CC110 to CC161) corresponding to the TV channel (SECAM-L system) from a French cable TV

station, based on the broadcast frequency of the TV channel. When you do not know the broadcast frequency, please contact

the cable TV station.

• The CH/CC numbers of CH102-CH169 and CC110-CC161 correspond to the TV channels being broadcast by a SECAM-L

system. The other CH/CC numbers correspond to the TV channels being broadcast by a method other than a SECAM-L

system.

Download from Www.Somanuals.com. All Manuals Search And Download.

TV BUTTONS AND PARTS

! Front Panel

1 Remote control sensor and ECO sensor

2 Power lamp

6 r(Volume) button

7 EXT-4 terminal

8 3D lamp

page 8

pages 3 and 6

pages 23 and 35

3 Main power button

The 3D lamp lights while the 3D-PHONIC function is in

use.

4 Headphone jack (mini jack)

5 P pButtons / qbuttons

page 35

page 8

9 ECO lamp

If you set the ECO MODE function to ON, the ECO lamp

lights.

0 SLEEP TIMER lamp

The SLEEP TIMER lamp lights while the SLEEP TIMER

function is operating.

! Rear Panel

- Aerial socket

page 2

@ AUDIO OUT terminal

page 37

page 36

= EXT-1 terminal

~ EXT-2 terminal

! EXT-3 terminal

pages 2, 23 and 35

pages 2, 5, 23 and 35

pages 23 and 35

# SURROUND REAR terminal

$ DIGITAL AUDIO IN terminal

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

If a problem arises while you are using the TV, please read this “Troubleshooting” well before you request having the TV

repaired. You may be able to fix it easily by yourself. For example, if the AC plug is disconnected from the AC outlet, or the TV

aerial has problems, you may think there is a problem with the TV itself.

Important:

• This Troubleshooting guide only covers problems whose cause are not easy to determine. If a question arise when you are

operating a function, read the page(s) corresponding to the operation of the function well, not this Troubleshooting guide.

• After you have followed the Troubleshooting description or the operating description of the functions concerned without any

success, remove the AC plug from the AC outlet and request a repair of your TV. Do not attempt to repair the TV by yourself

or remove the rear cover of the TV.

• When a white and bright still image (such as a white dress)

is displayed on the screen, the white part may look as if it

were coloured. It is a phenomenon unavoidable due to the

nature of the picture tube itself, and not due to a TV failure.

If you cannot turn on the TV

• Is the AC plug connected to the AC outlet?

• Is the Power lamp lit? If not, press the Main power button.

When the picture disappears from the screen, the

unnatural colours will also disappear.

No picture/No sound

• When viewing images from commercially available video

software products, or videos from videotapes which have

been recorded improperly, the top of the image may be

distorted. This is due to the condition of the video signal,

and not because of malfunction.

• Have you chosen a TV channel whose reception is

extremely bad? In this case, the BLUE BACK function will

be activated, the entire screen becomes blue, and the

sound is muted. In spite of this, if you want to view the TV

channel, follow the description “BLUE BACK” on page 25

to try to change the BLUE BACK function setting to OFF.

• Have you connected the headphones to the TV?

Connecting the headphones to the TV causes sounds not

to be issued from the TV speakers.

Poor sound

• Have you adjusted BASS or TREBLE properly? If not,

follow the description “Sound Adjustment” on page 18 to try

to adjust them properly.

• Have you set the SPEAKER function to OFF? Follow the

description “SPEAKER” on page 18 to confirm the

SPEAKER function setting to try to solve the problem.

• If the SYSTEM setting for a TV channel is incorrect, it may

prevent the sound from being issued. Follow the

• When the TV channel reception is poor, it can be hard to

hear the stereo or bilingual sound. In this case, follow the

description “STEREO / I•II” on page 18 to hear the sound

more easily by changing it to a mono sound.

description “EDIT/MANUAL” on page 28 to use the

MANUAL function to try to change the SYSTEM setting.

Operation disabled

• Have the batteries of the remote control become

exhausted? Follow the description “Putting Batteries into

the Remote Control” on page 2 and replace them with new

batteries to try to solve the problem.

Poor picture

• If noise totally obscures the picture (snow), the aerial or

aerial cable may have trouble. Check the following to try to

solve the trouble:

• Have you attempted to use the remote control at the sides

or rear of the TV or at a location more than seven meters

apart from the TV location? Operate the remote control in

the front of your TV or a location less than seven meters

from your TV to try to solve the problem.

Has the TV and aerial been connected properly?

Has the aerial cable been damaged?

Is the aerial pointed to the right direction?

Is the aerial itself faulty?

• If the TV or aerial receives interference from the other

devices, stripes or noise may appear in the picture. Move

such devices as an amplifier, personal computer, or a hair

drier that can cause interference away from your TV, or try

changing its location. If the aerial suffers interference from

a radio tower or high-voltage wire, please contact your

local dealer.

• If the TV receives interference from signal reflecting from

mountains or building, double-pictures (ghosting) will

occur. Try to change the aerial’s direction or replace the

antenna with the one with better directionality.

• Are your COLOUR SYSTEM settings for the TV channels

correct? Follow the description “COLOUR SYSTEM” on

page 17 to try to solve the trouble.

• When you are viewing a teletext programme, you cannot

operate the menus. Press the

teletext programme to the ordinary TV programme to try

operating the menus.

button to return the

• If the TV operation becomes disabled suddenly, press the

Main power button on the TV and turn off the main power.

Try to press the Main power button again to turn on the

main power. If the TV returns to a normal state, it is not a

failure.

• Use the HEADPHONE function to adjust the volume of the

headphones. For details, refer to “HEADPHONE” on

page 19.

• Has COLOUR or BRIGHT been controlled properly?

Follow the description “Picture Adjustment” on page 15 to

try to adjust them properly.

• Videotaping teletext is not recommended because it may

not record correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Other concerns

• When the SLEEP TIMER function operates, the TV is

automatically turned off. If the TV is turned off suddenly, try

to press the

(Standby) button to turn on the TV once

again. At this time, if the TV resumes a normal state, there

is no problem.

• When a WSS signal is included in the broadcast signal or

the signal from an external device, or when the TV is

receiving a control signal from an external device, the

ZOOM mode will change automatically. When you want to

return to the previous ZOOM mode, press the

button to choose the ZOOM mode again.

• If you bring a magnetised device such as a speaker near to

your TV, a picture may be warped or unnatural colors

appear at the corners of the screen. In this case, keep the

device apart from your TV. If the speakers causes such

phenomena, use the magnetic-shielded speakers instead.

• A picture may be tited due to the influence of the earth’s

magnetism. In this case, use the “PICTURE TILT” on

page 17 to complete the tilt.

• It takes a short period of time from the time an operation

such as changing channels is performed until an image is

displayed. This is not a malfunction. This is the time

required for the image to stabilize before it can be

displayed.

• The TV may emit a crackling sound due to a sudden

change in temperature. It does not matter if a picture or

sound does not show any abnormality. If you hear crackling

sounds frequently while you are viewing the TV, other

causes may be assumed. For precautionary purposes,

request your service technician to inspect it.

• Touching the screen may cause you feel a slight electric

shock due to its static electricity. It is an unavoidable

phenomenon due to the construction of the picture tube. It

is not a problem with the TV. You can rest assured that this

static discharge does not have harmful influence over the

human body.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Model

Item

AV32Z10EU*

Broadcasting systems

Colour systems

CCIR B/G, I, D/K, L

PAL, SECAM

• The EXT terminals also support the NTSC 3.58/4.43 MHz system.

Channels and frequencies

• E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY H+2, F2-F10, F21-F69,

R1-R12, R21-R69

• French cable TV channel of broadcast frequencies 116 - 172 MHz and 220 - 469 MHz

Sound-multiplex systems

Teletext systems

Power requirements

Power consumption

Picture tube size

Audio output

A2 (B/G, D/K), NICAM (B/G, I, D/K, L) system

FLOF (Fastext), TOP, WST (World Standard System)

220 - 240 V AC, 50 Hz

Maximum: 293 W, Average: 153 W, Standby: 2.8 W

Viewable area 76 cm (measured diagonally)

Rated Power output: 20 W + 20 W + 5 W

Speakers

10 cm round × 2, 3.5 cm round × 2, (10 cm × 3 cm) oval × 1

EXT-1 terminal

Euroconnector (21-pin, SCART)

• Video input, Audio L/R inputs and RGB inputs are available.

• TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.

• Video and Audio L/R outputs are available.

• T-V LINK functions are available.

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

RCA connectors × 3

S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

AUDIO OUT terminal

RCA connectors × 3

• Variable audio L/R outputs and subwoofer output are available.

• Variable out 0-1 Vrms, low impedance

SURROUND REAR terminal

Speaker terminals for external for surround speakers.

• Surround rear sounds are output to the speakers.

• For impedance 8-ohm speakers only.

• Rated power output: 7.5 W + 7.5 W

DIGITAL AUDIO IN terminal

Coaxial connector × 1

Optical connector × 1

• Dolby Digital is available.

Headphone jack

Dimensions (W × H × D)

Weight

Stereo mini-jack (3.5 mm in diameter)

855 mm × 550 mm × 568 mm

56.9 kg

Accessories

Remote control unit × 1 (RM-C58 (Silver) or RM-C52 (Black) is supplied.)

AAA/R03 dry cell battery × 2

* A basic model number. The actual model number may have characters added (such as “S” denoting silver) indicating the

colour of the TV set.

Design and specifications subject to change without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration

purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as

this constitutes an infringement of copyright.

Download from Www.Somanuals.com. All Manuals Search And Download.

Integra Stereo Receiver DTR 73 User Manual
Invacare Mobility Aid IVC Tracer SX5 User Manual
Jeep Automobile 12MK74 126 AA User Manual
Jensen Portable Speaker SMPS 85 User Manual
JVC VCR HR J255SA User Manual
Karcher Pressure Washer K 1800 IB User Manual
Kenwood Battery Charger KSC 24 User Manual
Kenwood CD Player 76 User Manual
Kidde Fire Extinguisher XL25MP User Manual
Kodak Digital Camera CD1013 User Manual