Contents
AV Receiver
Before using
2
8
DTR-7.3
Instruction Manual
Facilities and connections
Setup and operation
Remote controller
Appendix
29
61
73
Thank you for purchasing the
AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit. Following the
instructions in this manual will enable you to obtain
optimum performance and listening enjoyment
from your new AV Receiver. Please retain this
manual for future reference.
E
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
22. Safety Check – Upon completion of any service or repairs to the
appliance, ask the service technician to perform safety checks to
determine that the appliance is in proper operation condition.
FIGURE 1:
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
23. Wall or Ceiling Mounting – The appliance should be mounted
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
to a wall or ceiling only as recommended by the manufacturer.
24. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other appli-
ances (including amplifiers) that produce heat.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
25. Liquid Hazards – The appliance shall not be exposed to drip-
ping or splashing and no objects filled with liquids, such as
vases shall be placed on the appliance.
GROUND CLAMPS
POWER SERVICE GROUNDING
NEC – NATIONAL ELECTRICAL CODE
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
Precautions
1. Recording Copyright
For U.S. models
Recording of copyrighted material for other than personal use is
illegal without permission of the copyright holder.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s at-
tention to Section 820-40 of the NEC which provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
2. AC Fuse
The fuse is located inside the chassis and is not user-serviceable. If
power does not come on, contact your Integra/Onkyo authorized
service station.
3. Care
FCC Information for User
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak
solution of mild detergent and water, wring it out dry, and wipe off the
dirt. Following this, dry immediately with a clean cloth. Do not use
rough material, thinners, alcohol or other chemical solvents or cloths
since these could damage the finish or remove the panel lettering.
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.
Worldwide models are equipped with a voltage selector to conform
to local power supplies. Be sure to set this switch to match the volt-
age of the power supply in your area before plugging in the unit.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
For British models
Replacement and mounting of an AC plug on the power supply cord
of this unit should be performed only by qualified service personnel.
IMPORTANT
The wires in the mains lead are colored in accordance with the fol-
lowing code:
For Canadian models
Blue : Neutral
Brown : Live
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
As the colors of the wires in the mains lead of this apparatus may
not correspond with the colored markings identifying the terminals
in your plug, proceed as follows:
The wire which is colored blue must be connected to the terminal
which is marked with the letter N or colored black.
The wire which is colored brown must be connected to the terminal
which is marked with the letter L or colored red.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CON-FORME À LA NORME NMB-003 DU
CANADA.
IMPORTANT
A 5 ampere fuse is fitted in this plug. Should the fuse need to be
replaced, please ensure that the replacement fuse has a rating of 5
amperes and that it is approved by ASTA or BSI to BS1362. Check
for the ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME THEN THE FUSE
SHOULD BE REMOVED AND THE PLUG CUT OFF AND DIS-
POSED OF SAFELY. THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMPERE SOCKET.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
If in any doubt, consult a qualified electrician.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Miscellaneous connections ............................. 26
Connecting for remote control ( ) .............................. 26
Connecting the power cords from other devices ........... 26
RS 232 port ..................................................................... 26
AC INLET ...................................................................... 26
Before using
Important Safeguards......................................... 2
Precautions ......................................................... 3
Contents .............................................................. 4
Features ............................................................... 6
Supplied accessories ......................................... 6
Connecting to an external device with 12V TRIGGER
terminal ................................................................... 27
Before using this unit ......................................... 7
Installing the remote controller batteries ......................... 7
Using the remote controller.............................................. 7
Connecting to devices with analog multi channel output .... 27
Connecting auxiliary power amplifier ........................... 27
Connecting the power ...................................... 28
Turning on the power ..................................................... 28
Turning on the power from the remote controller ......... 28
Facilities and connections
Index parts and facilities.................................... 8
Front panel ........................................................................ 8
Front panel display ......................................................... 10
Remote controller ........................................................... 11
Rear panel ....................................................................... 13
Setup and operation
Enjoying music or videos with the DTR-7.3 ..... 29
Basic operation ............................................................... 29
To change the display of the input source from TAPE to MD .... 29
Temporarily turning off the sound ................................. 30
Adjusting the bass and treble ......................................... 30
Listening with headphones............................................. 30
Using the sleep time (remote controller only) ............... 30
Changing the listening mode.......................................... 31
Switching the display ..................................................... 32
Adjusting the brightness of the front display ................ 32
Temporarily changing the speaker output levels ........... 32
Changing the audio mode............................................... 33
Enjoying the multichannel output .................................. 33
Connecting to Audio/Video equipment .......... 14
Connecting your audio components .............................. 15
Connecting your video components .............................. 16
Connecting speakers ....................................... 20
Ideal speaker configuration ............................................ 20
Minimum speaker configuration for surround sound
playback .................................................................. 20
Speaker placement.......................................................... 20
Connecting speakers ....................................................... 21
Using the speaker labels ................................................. 21
Connecting antennas ....................................... 22
Assembling the AM loop antenna .................................. 22
Connecting the AM antenna cable ................................. 22
Connecting the included antennas ................................. 22
Connecting an FM outdoor antenna............................... 23
Connecting an AM outdoor antenna .............................. 23
Directional linkage ......................................................... 23
Listening to Radio Broadcasts........................ 34
Tuning into a radio station ............................................. 34
Listening to a stereo radio station (FM mode) .............. 34
Presetting a radio station ................................................ 35
Selecting a preset radio station ...................................... 35
Erasing a preset radio station ......................................... 35
Enjoying music in the remote zone ................ 36
Using the buttons on the DTR-7.3 ................................. 36
Using the remote controller............................................ 36
Adjusting the volume for the remote zone .................... 36
Connecting the antenna cable to the 75/300 Ω antenna adapter
(Australian models only) .............................................23
Connecting the remote zone (Zone 2) speakers.... 24
When using the SURR BACK/ZONE 2 SPEAKERS
terminals .................................................................. 24
Recording a source .......................................... 37
To record the input source signal you are currently
watching or listening to .......................................... 37
To record an input source signal different from that you
are currently watching or listening to..................... 38
When using the SURR BACK/ZONE 2 PRE OUT terminals ....... 24
When using the ZONE 2 OUT terminals....................... 24
Operating components not reached by the
remote controller signals (IR IN/OUT) ....... 25
Recording the video from one source and the audio from
another ..................................................................... 38
If the remote controller signal does not reach the
DTR-7.3 remote sensor........................................... 25
If the remote controller signal does not reach other
components ............................................................. 25
Setup Menu........................................................ 39
Navigating through the Setup Menu .............................. 40
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Hardware Setup................................................. 41
Entering a pre-programming code.................. 65
Learning a pre-programming code................................. 65
Pre-programming codes ................................................. 66
0. Hardware Setup Menu............................................. 41
0-1. Speaker Impedance Sub-menu ............................... 41
0-2. Surr Back/Zone 2 Sub-menu .................................. 41
0-3. IR IN Setup Sub-menu............................................ 42
Operating your programmed remote controller .... 67
DVD Mode (DVD Player Mode) ................................... 67
SAT Mode (Satellite Tuner Mode) ................................. 67
Cable Mode (Cable Mode) ............................................. 67
VCR Mode (VCR Mode) ............................................... 68
TV Mode (TV Mode) ..................................................... 68
Speaker Setup ................................................... 43
1. Speaker Setup Menu ................................................ 43
1-1. Speaker Config Sub-menu ...................................... 43
1-2. Speaker Distance Sub-menu ................................... 44
1-3. Level Calibration Sub-menu................................... 45
Programming the commands of remote controllers
for other devices into the remote controller ..... 69
Input Setup ........................................................ 46
Programming procedure ................................................. 69
Erasing the programmed command from one button .... 70
2. Input Setup Menu..................................................... 46
2-1. Digital Setup Sub-menu (When NET AUDIO is
not selected as the input source) ............................. 46
Erasing all the commands programmed under a Mode
button....................................................................... 70
2-2. Multichannel Setup Sub-menu (When NET
AUDIO is not selected as the input source) ........... 47
2-3. Video Setup Sub-menu ........................................... 48
2-4. Character Input Sub-menu ...................................... 49
2-5. IntelliVolume Sub-menu ......................................... 49
2-6. Listening Mode Preset Sub-menu .......................... 50
Using the macro function ................................ 71
What is the macro function? ....................................... 71
Programming the macro ................................................. 71
Executing the macro ....................................................... 71
Erasing a macro from the Macro 1 (or 2) button........... 72
Erasing all commands and macros that have been
2-7. 12V Trigger Setup Sub-menu ................................. 52
programmed ............................................................ 72
Audio Adjust...................................................... 53
3. Audio Adjust Setup Menu........................................ 53
3-1. Tone Control Sub-menu .......................................... 53
3-2. Surround Speakers Sub-menu ................................ 53
3-3. Sound Effect Sub-menu .......................................... 54
3-4. Delay Sub-menu...................................................... 54
3-5. LFE Level Sub-menu .............................................. 55
3-6. Mono Sub-menu...................................................... 55
3-7. Theater Dimensional Sub-menu ............................. 55
3-8. Surround Sub-menu ................................................ 56
3-9. THX Sub-menu ....................................................... 57
Appendix
Troubleshooting guide ..................................... 73
POWER .......................................................................... 73
SPEAKERS .................................................................... 73
FM/AM TUNER............................................................. 73
VIDEO and AUDIO ....................................................... 74
REMOTE CONTROLLER ............................................ 74
OTHER ........................................................................... 74
If one of the messages shown below appears ................ 75
3-10. 3-11. 3-12. 3-13. 3-14. 3-15. Mono Movie/Enhanced 7/
Orchestra/Unplugged/Studio Mix /TV Logic Sub-menu .... 57
Specifications ................................................... 76
Preference ......................................................... 59
4. Preference Menu ....................................................... 59
4-1. Volume Setup Sub-menu ........................................ 59
4-2. Headphones Level Setup Sub-menu....................... 60
4-3. OSD Setup Sub-menu ............................................. 60
4-4. OSD Position Sub-menu ......................................... 60
Remote controller
Using remote controller ................................... 61
Overview ........................................................................ 61
Controlling an Integra/Onkyo cassette tape deck .......... 61
Controlling an Integra/Onkyo DVD player ................... 62
Controlling an Integra/Onkyo CD player ...................... 63
Controlling an Integra/Onkyo MD recorder .................. 64
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Amplifier Features
I VLSC (Vector Linear Shaping Circuitry) for L/C/R
channels
I 100 Watts per channel min. RMS. into 8 Ω, 2 channel
driven, from 20 Hz to 20 kHz with no more than 0.08 %
THD (FTC rated)
I Net-Tune Function with MP3/WAV/WMA Decoding
I Ethernet cable plug-In Capability
I 7 Channel Amplifier
*
Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” “Surround EX” and the double-D symbol are
trademarks of Dolby Laboratories.
“Theater-Dimensional” is a trademark of Onkyo Corporation.
“NET-TUNE” is a trademark of Onkyo Corporation.
Lucasfilm THX and THX are trademarks or registered trademarks of THX
Ltd.
I Wide Range Amplifier Technology (WRAT)
I Linear Optimum Gain Volume Circuitry
•
•
•
I 192 kHz/24 Bit D/A Converters (except for Surround
Back L/R)
I Powered Zone 2 and 12V Trigger
•
•
Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd.
“DTS,” “DTS-ES Extended Surround” and “Neo:6” are trademarks of
Digital Theater Systems, Inc.
Audio/Video Features
I THX® Surround EX®
•
Windows Media, and the Windows logo are trademarks,
or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
I THX Select Certified
I Dolby®* Digital, Dolby Pro Logic II, Dolby Digital EX
•
•
Intel and Pentium are registered trademarks of Intel Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS
and THOMSON multimedia.
“XiVA” is a registered trademark of Imerge Limited.
Xantech is a registered trademark of Xantech Corporation.
Niles is a registered trademark of Niles Audio Corporation.
I DTS, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS
Neo:6, and DTS 96/24
I Theater-DimensionalTM Virtual Surround Mode
•
•
•
I Non-Scaling Configuration
I Onscreen displays (Basic Menu/Advanced Menu)
I Composite to S-Video Conversion
I 6 S-Video Inputs/3 Outputs
The alphabet displayed at the end of the product name found in
catalogs and on the packages represents the color of this
receiver. Though the color varies, the specifications and
operations are the same.
I 6 Assignable Digital Inputs (3 optical/3 coaxial), 1 output,
and 1 Digital Input (optical)
THX Select
I Pre Out Terminals for Front L/R, Center, Surround L/R,
Before any home theatre component can be THX Select
certified, it must pass a rigorous series of quality and
performance tests. Only then can a product feature the THX
Select logo, which is your guarantee that the Home Theatre
products you purchase will give you superb performance for
many years to come. THX Select requirements define
hundreds of parameters, including power amplifier
performance, and pre-amplifier performance and operation
for both digital and analog domains. THX Select receivers
also feature proprietary THX technologies (e.g., THX Mode,
see page 52) which accurately translate film soundtracks for
home theater playback.
Surround back L/R or Zone 2 L/R and Subwoofer
FM/AM Tuner Features
I 40 FM/AM random presets
I FM auto tuning
Other Performance Features
I IntelliVolume
I Character Input
I Powerful backlit/preprogrammed learning remote with
macro and mode-key LEDs
Supplied accessories
Check that the following accessories are supplied with the DTR-7.3.
AM loop antenna × 1
FM indoor antenna × 1
75/300 Ω antenna adapter × 1
(Australian models only)
Power cord × 1
The power cord may
differ depending on
the region.
Protective caps for the Video
5 jacks on the front of the
DTR-7.3. Be sure to always
1
2
3
Speaker Cable
attach the protective caps
when you are not connecting
a device to the Video 5 jacks.
Protective caps
For digital jack × 1
For analog jack × 1
Remote controller × 1
Batteries (AA, R6 or UM-3) × 2
Speaker cable label × 1
(See page 21)
The alphabet displayed at the end of the product name found in catalogs and on the packages represents the color of this player.
Though the color varies, the specifications and operations are the same.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using this unit
Installing the remote controller batteries
Using the remote controller
Point the remote controller toward the remote control sensor. The
STANDBY indicator lights up when the unit receives a signal from
the remote controller.
1. Remove the battery compartment cover by pressing it
and sliding it in the direction shown by the arrow
below.
Remote control sensor
DTR-7.3
2. Insert two AA (R6 or UM-3) batteries into the battery
compartment. Carefully follow the polarity diagram
(positive (+) and negative (–) symbols) inside the
battery compartment.
STANDBY indicator
3. After the batteries are installed and seated correctly,
replace the compartment cover.
1
2
3
30˚
30˚
Approx. 16 feet
(5 meters)
Notes:
• Do not mix new batteries with old batteries or different kinds of
batteries.
Notes:
• To avoid corrosion, remove the batteries if the remote controller
• Make sure that the remote control sensor is not subject to strong
light such as direct sunlight or inverted fluorescent light for it
may prevent proper operation of the remote controller.
• Using another remote controller in the same room or using the
DTR-7.3 near equipment that uses infrared rays may cause
operational interference.
will not be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
remove the old batteries and replace them both with two new AA
batteries.
• Do not put objects on the remote controller. Its buttons may be
pressed by mistake and drain the batteries.
• Make sure the audio rack doors do not have colored glass.
Placing the DTR-7.3 behind such doors may prevent proper
remote controller operation.
• If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Index parts and facilities
Front panel
For further operational instructions, see the pages indicated in
brackets [ ].
Listening mode buttons [31, 51]
Press these buttons to select a listening mode for the current input
source.
Direct/Pure Audio: Press to switch between the direct and pure
audio listening modes.
Stereo: Selects for the stereo listening mode.
Surround: Selects for the Dolby Pro LogicII, DTS Neo:6, Dolby
Digital, or DTS listening modes.
Standby/On button [28]
If pressed with the receiver plugged in, the DTR-7.3 turns on and the
display lights up. If pressed again, the DTR-7.3 returns to the
standby state. In the standby state, the display is turned off and the
DTR-7.3 cannot be operated.
THX: Selects for the THX listening mode.
DSP / : Switches to the DSP mode.
Standby indicator [7, 28]
Lights when the DTR-7.3 is in the standby state and when a signal is
received from the remote controller.
Front display
Memory button [35]
Audio Selector button [33]
Press to assign the radio station that you are currently tuned into to a
preset channel or press to delete a previously preset station.
Press to select the type of audio input signal.
Remote control sensor [7]
FM Mode button [34]
Press to change the stereo mode from AUTO to MONO and vice
versa. Each time this button is pressed, the AUTO indication turns
on and off indicating the current mode. If you are listening to an FM
radio station in stereo and the sound cuts out or there is a great deal of
noise, switch from AUTO to MONO.
Display button [32]
Press to display information about the current input source signal.
Each time you press the display button, the screen changes to show
you different information concerning the input signal.
Dimmer button [32]
Tuning / , Preset / , cursor buttons [34, 35, 40]
Press to set the brightness of the front display. There are three
settings available: normal, dark, and very dark.
To tune into a radio station, press the Tuning
/
buttons. The tuner
frequency is displayed in the front display and it can be changed in
100-kHz (or 50-kHz) increments for FM and 10-kHz (or 9-kHz)
increments for AM.
• The brightness of the front display can also be performed using
the remote controller.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Index parts and facilities
When FM is selected as the input source, you can hold down either
the Tuning or button and then release it to activate the auto-
search feature. It will search for a station in the direction of the
button you pressed and stop when it tunes into one. When navigating
through the menu settings, these buttons move the cursor up or down
(or change the highlighted item).
Input source buttons and indicators (DVD, Video
1–5, Tape, Tuner, Phono, CD, and Net Audio) [29,
36-38]
Press these buttons to select the input source for the main zone.
To select the input source for the remote zone (Zone 2) or recording
out (Rec Out), first press the Zone 2 or Rec Out button, and then
press the desired input source button. The input channel with its
indicator lit red is output to REC OUT and the one with its indicator
lit green is output to ZONE 2.
To select a radio station that was stored using the Memory button,
press the Preset
When navigating through the menu settings, these buttons select the
value or item that you selected with the Tuning buttons.
/
buttons.
/
When you press the Setup button, the Tuning and Preset buttons
become cursor buttons to be used for Setup Menu operations.
Upsampling indicator [54]
Lights during upsampling. This function is available when the input
source is Analog/PCM and the listening mode is set to the stereo or
surround mode.
Rec Out/Zone 2/Off buttons [36-38]
These buttons allow you to use the DTR-7.3 to output to a remote
zone (Zone 2) or to another component for recording (Rec Out).
Press the Rec Out button to output the audio and video signals to a
recording component for recording. Press the Zone 2 button to enjoy
the output from the DTR-7.3 in a different room, which is referred to
as the remote zone (Zone 2).
When either button is pressed, the currently selected input source for
recording or outputting to the remote zone is displayed in the front
panel display. If “SOURCE” is displayed, then the same input
source as that selected for the main zone will be output.
To select an input source, press the desired button (Rec Out or Zone
2) and then press one of the input source button within 8 seconds.
That source will be output for recording or viewing in the remote
zone.
Phones jack [30]
This is a standard stereo jack for connecting stereo headphones.
Pure Audio indicator [31]
Lights during pure audio playback.
To set the output to the source channel, press the desired button (Rec
Out or Zone 2) twice in succession. To turn off the output, press the
desired button (Rec Out or Zone 2) and then press the Off button
within 8 seconds.
Note:
The Rec Out and Zone 2 buttons use the same circuit and therefore
cannot be used at the same time. When Rec Out is selected, nothing
is output to Zone 2. When Zone 2 is selected, Rec Out is
automatically fixed to SOURCE.
Setup button [40]
Press to enter the Setup Menu. The OSD Menu will appear on the TV
monitor as well as the front display on the DTR-7.3.
Enter button [40]
Press to display the screen for the item that is selected in the Setup
Menu.
Return button [40]
When in the Setup Menu, press to go back one level. If pressed while
at the Main Menu, you will exit the Setup Menu.
Master Volume dial [29]
Use to control the volume in the main zone. The volume for the
remote zone (Zone 2) is independent
Video 5 Input terminals [19]
Protective caps are provided
for the Video 5 jacks. Be
sure to always attach the
protective caps when you
are not connecting a device
to the Video 5 jacks.
Protective caps
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Index parts and facilities
Front panel display
Input signal path indicators
Multi function display
Shows from which terminal the input signal is coming.
During normal operation, shows the current input source. When the
FM or AM input is selected, shows the frequency and preset number.
When the Display button is pressed, shows the listening mode and
input source format. However, does not show the source format
when the FM or AM source is selected.
Listening mode or digital input format indicators
One of these indicators lights to show the format of the current input
source. In addition, one of the listening mode indicators lights to
indicate the current listening mode.
Volume display
Tuning indicators
Shows the volume level.
TUNED indicator
Lights when a radio station is received.
SLEEP indicator
Lights when the sleep timer is turned on.
AUTO indicator
Lights when receiving FM broadcasts in the stereo mode. Turns
off when placed into the monaural mode.
FM STEREO indicator
Lights when an FM broadcast station is received in stereo.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Index parts and facilities
Remote controller
The RC-514M is a multi-functional remote controller. The
instructions given here only explain how to use the remote controller
in conjunction with the DTR-7.3. To operate the DTR-7.3 using the
remote controller, first press the RCVR Mode button to place the
remote controller in the receiver mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Index parts and facilities
Send/Learn indicator
Display button [32]
Lights red when signals are sent by the remote controller. It also
flashes when a button is pressed when the battery power is low.
For changing the display in the front display.
Dimmer button [32]
On/Standby button [28]
Adjusts the display brightness.
There are three settings available: normal, dark, and very dark.
On: Press to turn on the DTR-7.3.
Standby: Press to place the DTR-7.3 in the standby state.
Light button
Be aware that pressing the Standby button only places the DTR-7.3
in standby and does not turn the power completely off.
Press to turn on and off the lights in the buttons of the remote
controller.
Sleep button [30]
Setup button [40]
Press to set the sleep function.
Press to display the Setup Menu on the TV screen and in the display.
Press again to exit the menu.
The SLEEP button enables you to set the DTR-7.3 to turn off
automatically after a specified time period.
/ / / , ENTER button [40]
Macro 1, 2 button [71]
When in the Setup Menu, press the upper and lower arrow buttons to
select an item, press the right and left arrow buttons to select
parameter values or modes, and press the ENTER button to advance
to the next item.
Press to program or execute the macro function.
Mode buttons and indicators [28, 61]
Press to select the component to be operated by the remote
controller. When a Mode button is pressed, it will light for 8 seconds.
The selected Mode button will also light whenever any other
operation button is pressed.
VOL
button [29]
Press to adjust the volume.
Test button [45]
Return button [40]
This button is used to set the speaker output levels. Use this button in
Press to enter the selected setting and return to the previous menu.
conjunction with the Level
/
and CH Sel buttons to calibrate the
speakers levels without entering the Setup Menu.
CH
button [35]
Press to select a preset channel for the tuner.
Muting button [30]
Press to activate the mute function.
CH Sel button [32, 45]
Press to select a speaker channel when adjusting the speaker level.
Zone 2 button [36]
Press to perform operations on the remote zone.
Audio Sel button [33]
Press to select the audio input signal. The setting changes from
“Auto” to “Multich” to “Analog” and back each time this button is
pressed.
Level
/
buttons [32, 45]
Press to adjust the volume of the speaker selected using the CH Sel
button.
Operation buttons [61]
Press to operate other devices connected to the DTR-7.3.
Input Selector buttons [29, 36-38]
Press to select an input source.
Same as the input selector buttons on the front panel of the DTR-7.3.
The input source for each button is given here. DVD:DVD, CD:CD,
V1:VIDEO1, V2:VIDEO2, V3:VIDEO3, V4:VIDEO4,
V5:VIDEO5, TAP:TAPE, TUN:FM/AM, PH:PHONO.
Listening mode buttons [31, 51]
You can select a listening mode.
Re-EQ button [54, 57]
Depending on the listening mode, you can turn the Re-EQ function
on or off.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Index parts and facilities
Rear panel
DIGITAL
INPUT
PRE OUT
R
L
COMPONENT
VIDEO
AUDIO
VIDEO
S VIDEO
ANTENNA
FRONT SPEAKERS
SURR SPEAKERS
COAX
FRONT
SUB
OUTPUT
AV RECEIVER
MODEL NO. DTR 7.3
MONITOR
R
L
R
L
OUT
1
2
3
Y
-
R
L
CENTER
AM
OUT
IN
ZONE 2
DVD
P
B
AC OUTLETS
SURR
PR
SURR
R
L
BACK/
OPT
1
INPUT 1
Y
ZONE
2
FM
75
OUT
IN
ETHERNET
[NET-TUNE]
VIDEO 1
SURR
FRONT
MULTI CH
INPUT
CENTER
BACK/
ZONE 2
SPEAKERS
2
3
P
B
SPEAKER
AUDIO
R
L
AC 120V 60Hz
SWITCHED
:
CAUTION
R
L
SUB
CENTER
SPEAKER
TOTAL 120W 1A MAX.
PHONO
OUT
IN
PR
IMPEDANCE
4
6
OHMS MIN. OR
OHMS MIN.
R
L
VIDEO 2
INPUT 2
Y
SURR
/SPEAKER
CD
SEE INSTRUCTION
MANUAL FOR
DIGITAL
OUTPUT
IR
AC INLET
A
ZONE 2
12V
TRIGGER OUT
R
L
CORRECT SETTINGS.
OUT
IN
RS232
OPT
IN
VIDEO
VIDEO
3
4
P
B
R
SURR
BACK
TAPE
IN
IN
P
OUT
B
REMOTE
CONTROL
GND
R
L
R
L
AUDIO
AUDIO
VIDEO
S VIDEO
For more information regarding connection procedures, see pages
indicated in brackets [ ].
MULTI CH INPUT [27]
This connector is for connecting components with a multi-channel output.
DIGITAL INPUT/OUTPUT [15-19]
PHONO/CD/TAPE AUDIO IN/OUT [15]
These jacks are for connecting components with digital input and
output capabilities. To connect a CD player, see page 15; to connect an
MD or CD recorder, see page 15; to connect a DAT deck, see page 15;
to connect a DVD player, see page 16; to connect a DVD recorder, see
page 18; and to connect a digital satellite tuner, see page 19.
These connectors are for connecting to the audio input and output
jacks on audio components. To connect a turntable, see page 17; to
connect a CD player, see page 17; and to connect a cassette tape
deck, MD recorder, or CD recorder, see page 17.
PRE OUT [27]
DVD/VIDEO1-4 IN/OUT [16-19]
To use the DTR-7.3 as a preamplifier, connect a power amplifier to
this jack.
These connectors are for connecting to the video input and output
jacks on video components. To connect a DVD player, see page 16;
to connect a DVD recorder, see page 18; to connect a VCR, see page
17; and to connect a satellite tuner, see page 19.
ANTENNA [22-23]
These jacks are for connecting a tuner.
COMPONENT VIDEO INPUT1/2 [16, 18]
These connectors are for connecting to the component video outputs
of video components that have them. To connect a DVD player, see
page 16; to connect a DVD recorder, see page 18; and to connect a
satellite tuner, see page 19.
ZONE2 AUDIO/VIDEO OUT [24]
These jacks are for connecting the components that will be used in the
remote zone (Zone 2). For more details on the connection procedures,
see “Connecting the remote zone (Zone 2) speakers” on page 24.
RS232 [26]
MONITOR OUT VIDEO/S VIDEO [17]
This connector is for connecting to the RS232 port of an external device.
These jacks are for connecting to the video input jacks on television
monitors or projectors.
IR IN/OUT [25]
These connectors are for connecting the remote sensor of a multi-
room kit (sold separately).
COMPONENT VIDEO OUTPUT [17]
These jacks are for connecting to the component video input jacks on
television monitors or projectors.
12V TRIGGER OUT A/B/ZONE 2 [27]
This connector is used to connect to the 12V TRIGGER IN terminal
of a component.
ETHERNET (NET-TUNE)
This connector is for connecting to an Ethernet network or personal
computer.
[26]
This jack is for connecting other Integra/Onkyo components
SPEAKERS [20-21]
equipped with the same
terminal.
These terminals are for connecting the speakers.
AC INLET [26]
AC OUTLETS [26]
This connector is for connecting the supplied power cord.
13
This AC outlet is provided to plug in the power cord from another
component.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio/Video equipment
• Be sure to always refer to the instructions that came with the
component that you are connecting.
Cables are depicted in the connection diagrams as shown below.
• Do not plug in the power cord until all connections have been
properly made.
Left (white)
L
Audio connection cable
• For input jacks, red connectors (marked R) are used for the
right channel, white connectors (marked L) are used for the
left channel, and yellow connectors (marked V) are used for
video connection.
Right (red)
R
• Insert all plugs and connectors securely. Improper
connections can result in noise, poor performance, or
damage to the equipment.
P
R
B
P
P
R
P
Y
B
Component video
connection cable
Y
Improper connection
Video connection cable
S video connection cable
Inserted completely
• Do not bind audio/video connection cables with power cords
and speaker cables. Doing so may adversely affect the
picture and sound quality.
Coaxial cable
Optical cable
• The optical digital jacks are all of the shutter-type
construction. Connect an optical cable by first making sure
the cable is oriented correctly and then inserting it into the
jack pushing the shutter lid inwards.
Rear optical jack
Front optical jack
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio/Video equipment
Here is an explanation of typical ways to connect various components to the DTR-7.3. There are many ways that any one component can be
connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be
thought of as such. It is best to fully understand the nature of each connector and terminal as well as those of your components and their features
to ascertain which method of connection is best.
: Signal flow
Grand white (earth)
Digital audio output (optical)
R (red)
DIGITAL
INPUT
PRE OUT
R
L
Analog audio output
ANTENNA
COAX
FRONT
SUB
1
2
3
Digital audio input (optical)
CENTER
L (white)
AM
SURR
2. Turntable (PH)
SURR
R
L
BACK/
OPT
1
ZONE
2
FM
75
3. Cassette tape deck, MD
recorder, DAT deck, or CD
recorder (TAPE)
FRONT
MULTI CH
INPUT
2
3
AUDIO
R
L
R
L
SUB
CENTER
PHONO
R (red)
Analog audio output
SURR
CD
DIGITAL
OUTPUT
R (red)
R
L
OUT
OPT
L (white)
SURR
BACK
TAPE
IN
Analog audio input
Analog audio output
L (white)
R (red)
1. CD player (CD)
GND
R
L
AUDIO
Digital audio output (optical)
L (white)
2. Connecting a turntable (PHONO)
Connecting your audio components
Using an RCA audio cable, connect the output jacks of the turntable
to the PHONO audio jacks of the DTR-7.3. Make sure that you
properly connect the left channel to the L jack and the right channel
to the R jack.
Below is an example of how you can connect your audio components
to the DTR-7.3. Refer to the diagram above for the following
connection examples.
AUDIO IN/OUT
Note:
The DTR-7.3 is designed for use with moving magnet cartridges. For
proper operation, connect a ground (or earth) wire to the GND
terminal. For some turntables, however, connecting the ground wire
may cause increased noise, and in such a case, a ground wire is not
necessary and should not be connected.
These are the analog audio inputs and outputs. There are eight audio
inputs and three audio outputs on the rear panel. The audio inputs
and outputs require RCA-type connectors.
DIGITAL INPUT/OUTPUT
On the rear panel of the DTR-7.3, there are three coaxial digital
inputs, three optical digital inputs, and one optical digital output. To
the digital inputs, connect CD players, LD players, DVD players, or
other digital source component. To the digital output, connect MD
recorders, CD recorders, DAT decks, or other similar components.
3. Connecting a cassette tape deck, MD recorder, DAT deck, or
CD recorder (TAPE)
Using RCA audio cables, connect the output jacks (PLAY) of the
device to the TAPE AUDIO IN jacks of the DTR-7.3 and connect
the input jacks (REC) of the device to the TAPE AUDIO OUT jacks
of the DTR-7.3. Make sure that you properly connect the left
channels to the L jacks and the right channels to the R jacks.
• Since an analog connection must be made when using REC OUT
or ZONE 2, make sure that the connection to the input source is
not digital only, but analog as well.
If the device has a digital output, connect it to either the DIGITAL
INPUT COAX jack or DIGITAL INPUT OPT jack of the DTR-7.3
depending on the type of connector on the device.
• When using an optical input or output jack, always use an optical
fiber cable.
1. Connecting a compact disc player (CD)
With the initial settings of the DTR-7.3, the TAPE input source
is set for digital input at the OPT 2 jack.
If the digital connection is made to a different jack, this must be
Using an RCA audio cable, connect the output jacks of the compact
disc player to the CD AUDIO jacks of the DTR-7.3. Make sure that
you properly connect the left channel to the L jack and the right
channel to the R jack.
changed at Setup Menu: Input Setup → Digital Setup (see page 46).
If the device has a digital input, connect it to the DIGITAL OUTPUT
OPT jack of the DTR-7.3 for digital recording of the REC OUT
signal from the DTR-7.3.
If the compact disc player has a digital output, connect it to either the
DIGITAL INPUT COAX jack or DIGITAL INPUT OPT jack of the
DTR-7.3 depending on the type of connector on the compact disc
player.
Note:
With the initial settings of the DTR-7.3, the CD input source is
set for digital input at the OPT 1 jack.
The output from the DIGITAL OUTPUT jack of the DTR-7.3 is
only the digital signal input to the DIGITAL INPUT jack.
If the digital connection is made to a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page
46).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio/Video equipment
Connecting a DVD Player
: Signal flow
Digital audio output (coaxial)
R (red)
Analog audio output
L (white)
DIGITAL
INPUT
PRE
COMPONENT
VIDEO
AUDIO
VIDEO
S VIDEO
R
TENNA
COAX
FRONT
SUB
OUTPUT
MONITOR
1
2
3
OUT
Y
Video output
R
L
AM
OUT
IN
ZONE 2
DVD
PB
SURR
S Video output
PR
SURR
R
BACK/
INPUT 1
Y
OPT
1
ZONE
2
FM
75
OUT
IN
ETHERNET
[NET-TUNE
VIDEO 1
FRONT
4. DVD player (DVD)
P
B
2
3
UDIO
L
R
:
CAUTION
SUB
SPEAKER
PHONO
OUT
IN
PR
IMPEDANCE
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
VIDEO 2
INPUT 2
Y
SURR
CD
SEE INSTRUCTI
MANUAL FOR
CORRECT SETT
DIGITAL
OUTPUT
R
OUT
IN
VIDEO 3
VIDEO 4
P
B
R
OPT
SURR
BACK
TAPE
IN
IN
P
GND
UDIO
L
R
L
AUDIO
VIDEO
S VIDEO
Y
PB
PR
Component video output
The flow of the video signals is as follows:
Connecting your video components
Signals that comes in from VIDEO and S-VIDEO INPUT are output
to VIDEO and S VIDEO, signals that comes in from COMPONENT
VIDEO INPUT are only output to COMPONENT VIDEO
OUTPUT. When connecting a video player to the COMPONENT
VIDEO INPUT jacks, be sure to connect your television to the
COMPONENT VIDEO OUTPUT jacks.
Below is an example of how you can connect your video components
to the DTR-7.3. Refer to the diagram above for the following
connection examples.
COMPONENT VIDEO INPUT/OUTPUT
For DVD players or other devices that have component video
connectors, the DTR-7.3 has two banks of component video input
connectors (Y, PB, PR) for direct component video input. The DTR-
7.3 also has one bank of component video output connectors for
direct component video output to the matrix decoder of a television,
projector, or other display device. By sending the pure component
video signal directly, the signal forgoes the extra processing that
normally would degrade the image. The result is vastly increased
image quality, with incredibly lifelike colors and crisp detail.
4. Connecting a DVD player (DVD)
Using an RCA video cable, connect the video output jack
(composite) of the DVD or LD player to the DVD VIDEO IN jack of
the DTR-7.3. Or if the DVD or LD player has an S video output jack,
connect it to the DVD S VIDEO IN jack with an S video cable. Or if
the device has component video outputs, connect them to one of the
banks of COMPONENT VIDEO INPUT jacks on the DTR-7.3.
With the initial settings of the DTR-7.3, the DVD input source is
set for the COMPONENT VIDEO INPUT 1 jacks.
If you connect the DVD or LD player to the COMPONENT VIDEO
INPUT 2 jacks, this must be changed at Setup Menu → Input Setup
→ Video Setup → Component Video (see page 48).
Using an RCA audio connection cable, connect the audio output
jacks of the DVD or LD player to the DVD AUDIO IN jacks of the
DTR-7.3. Make sure that you properly connect the left channel to the
L jack and the right channel to the R jack.
VIDEO IN/OUT
These are the video inputs and outputs. On the rear panel, there are
five video inputs and two video outputs and each one includes both
composite video and S video configurations.
Connect VCRs, VTRs, LD players, DVD players, and other video
components to the video inputs. Connect VCRs, VTRs, and other
recording components to the video outputs to make video
recordings.
• When connecting a VCR or other video component, make sure
you connect its audio and video leads to the same bank (e.g.,
both to VIDEO 3).
If the device has a digital output, connect it to either the DIGITAL
INPUT COAX jack or DIGITAL INPUT OPT jack of the DTR-7.3
depending on the type of connector on the DVD player.
• The VIDEO 5 inputs are located on the front panel.
With the initial settings of the DTR-7.3, the DVD input source is
set for digital input at the COAX 1 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page
46).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio/Video equipment
: Signal flow
Video input
5. TV monitor or projector
(MONITOR OUT)
S Video input
DIGITAL
INPUT
PRE
COMPONENT
VIDEO
AUDIO
VIDEO
S VIDEO
R
NNA
COAX
FRONT
SUB
OUTPUT
MONITOR
OUT
1
2
3
Y
Y
R
L
AM
OUT
IN
ZONE 2
DVD
PB
PB
Component video input
SURR
S Video input
Video input
PR
PR
SURR
R
BACK/
INPUT 1
Y
OPT
1
ZONE
2
FM
75
OUT
IN
ETHERNET
[NET-TUNE]
VIDEO 1
FRONT
C
S
P
B
2
3
IO
L
R
:
CAUTION
L (white)
R (red)
Analog audio
input
SUB
SPEAKER
PHONO
OUT
IN
PR
IMPEDANCE
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
VIDEO 2
INPUT 2
Y
SURR
CD
SEE INSTRUCTION
MANUAL FOR
DIGITAL
OUTPUT
R
CORRECT SETTING
OUT
IN
VIDEO 3
VIDEO 4
P
B
R
OPT
SURR
BACK
TAPE
IN
6. VCR (VIDEO 1)
IN
P
GND
L
R
L
IO
AUDIO
VIDEO
S VIDEO
R (red)
Analog audio
output
L (white)
Video output
S Video output
5. Connecting a television monitor or projector (MONITOR
OUT)
6. Connecting a video cassette recorder (VIDEO 1)
Using RCA video cables, connect the video output jack (composite)
of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the
DTR-7.3 and connect the video input jack of the video cassette
recorder to the VIDEO 1 VIDEO OUT jack of the DTR-7.3. Or if the
video cassette recorder has S video input and output jacks, connect
them to the VIDEO 1 S VIDEO IN and OUT jacks of the DTR-7.3
using S video cables. Or if the video cassette recorder has component
video outputs, connect them to one of the banks of COMPONENT
VIDEO INPUT jacks on the DTR-7.3.
The DTR-7.3 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit. Since both the signal from the S VIDEO
and VIDEO inputs are output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
Using an RCA video cable, connect the video input jack (composite)
of the device to the MONITOR OUT VIDEO jack of the DTR-7.3.
Or if the device has an S video input jack, connect it to the
MONITOR OUT S VIDEO jack of the DTR-7.3 using an S video
cable. Or if the device has component video inputs, connect them to
the bank of COMPONENT VIDEO OUTPUT jacks on the DTR-7.3.
With the initial settings of the DTR-7.3, the VIDEO 1 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the video cassette recorder to the COMPONENT
VIDEO INPUT 1 jacks, this must be changed at Setup Menu →
Input Setup → Video Setup → Component Video (see page 48).
Using RCA audio cable, connect the audio output jacks of the video
cassette recorder to the VIDEO 1 AUDIO IN jacks of the DTR-7.3
and connect the audio input jacks of the video cassette recorder to the
VIDEO 1 AUDIO OUT jacks of the DTR-7.3. Make sure that you
properly connect the left channels to the L jacks and the right
channels to the R jacks.
Note:
Note that the Setup Menu will only be displayed on the monitor
connected to MONITOR OUT (VIDEO and S VIDEO) and not
those connected to the COMPONENT VIDEO OUT PUT jacks.
If you are connecting a digital output device to the VIDEO 1 jack
instead of a VCR, connect it to either the DIGITAL INPUT COAX
jack or DIGITAL INPUT OPT jack depending on the type of
connector on the device.
With the initial settings of the DTR-7.3, the VIDEO 1 input
source is set for digital input at the COAX 2 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page
46).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio/Video equipment
Digital audio input (optical)
Digital audio output (coaxial)
: Signal flow
S Video input
Video input
DIGITAL
PRE
COMPONENT
VIDEO
OUTPUT
AUDIO
VIDEO
S VIDEO
R (red)
Analog audio
input
INPUT
R
TENNA
COAX
FRONT
SUB
MONITOR
1
2
3
OUT
Y
R
L
AM
OUT
IN
ZONE 2
DVD
P
P
B
L (white)
SURR
R
SURR
7. DVD recorder, other digital video
recording device (VIDEO 2)
R
BACK/
INPUT 1
Y
OPT
1
ZONE
2
FM
75
OUT
IN
ETHERNE
[NET-TUNE
VIDEO 1
FRONT
P
P
B
2
3
UDIO
L
R
:
CAUTION
SUB
SPEAKER
PHONO
OUT
IN
R
IMPEDANCE
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
VIDEO 2
INPUT 2
Y
SURR
CD
R (red)
SEE INSTRUCTI
MANUAL FOR
CORRECT SETT
DIGITAL
OUTPUT
R
OUT
IN
VIDEO 3
VIDEO 4
P
P
B
R
OPT
SURR
BACK
Analog audio
output
TAPE
IN
L (white)
IN
GND
L
R
L
UDIO
AUDIO
VIDEO
S VIDEO
Video output
S Video output
Y
PB
Component video output
PR
Note:
7. Connecting a DVD recorder or other digital video recording
device (VIDEO 2)
The output from the DIGITAL OUTPUT jack of the DTR-7.3 is
only the digital signal input to the DIGITAL INPUT jack.
Using RCA video cables, connect the video output jack (composite)
of the device to the VIDEO 2 VIDEO IN jack of the DTR-7.3 and
connect the video input jack of the device to the VIDEO 2 VIDEO
OUT jack of the DTR-7.3. Or if the device has S video input and
output jacks, connect them to the VIDEO 2 S VIDEO IN and OUT
jacks of the DTR-7.3 using S video cables. Or if the device has
component video outputs, connect them to one of the banks of
COMPONENT VIDEO INPUT jacks on the DTR-7.3.
With the initial settings of the DTR-7.3, the VIDEO 2 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the device to the COMPONENT VIDEO INPUT 1
jacks, this must be changed at Setup Menu → Input Setup → Video
Setup → Component Video (see page 48).
Using RCA audio cables, connect the audio output jacks of the
device to the VIDEO 2 AUDIO IN jacks of the DTR-7.3 and connect
the audio input jacks of the device to the VIDEO 2 AUDIO OUT
jacks of the DTR-7.3. Make sure that you properly connect the left
channels to the L jacks and the right channels to the R jacks.
If the device has a digital output, connect it to either the DIGITAL
INPUT COAX jack or DIGITAL INPUT OPT jack of the DTR-7.3
depending on the type of connector on the device.
With the initial settings of the DTR-7.3, the VIDEO 2 input
source is set for digital input at the COAX 3 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page 46).
If the device has a digital input, connect it to the DIGITAL OUTPUT
OPT jack of the DTR-7.3 for digital recording of the REC OUT
signal from the DTR-7.3.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio/Video equipment
: Signal flow
8. Settop box, video camera
(VIDEO 3)
DIGITAL
INPUT
PRE
COMPONENT
VIDEO
AUDIO
VIDEO
S VIDEO
R
NNA
COAX
OUTPUT
MONITOR
S Video output
Video output
OUT
1
2
3
Y
R
L
SUB
AM
OUT
IN
ZONE 2
DVD
PB
L (white)
R (red)
SURR
PR
SURR
R
BACK/
INPUT 1
Y
OPT
1
ZONE
2
FM
75
Analog audio
output
9. Satellite tuner or television
(VIDEO 4)
OUT
IN
ETHERNET
[NET-TUNE]
VIDEO 1
FRONT
CE
SP
P
B
2
3
O
L
R
:
CAUTION
SUB
SPEAKER
PHONO
OUT
IN
PR
IMPEDANCE
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
Digital audio output (optical)
VIDEO 2
INPUT 2
Y
SURR
CD
SEE INSTRUCTION
MANUAL FOR
DIGITAL
OUTPUT
S Video output
Video output
R
CORRECT SETTING
OUT
IN
VIDEO 3
VIDEO 4
P
B
R
OPT
SURR
BACK
TAPE
IN
IN
P
GND
L (white)
L
R
L
O
AUDIO
VIDEO
S VIDEO
Analog audio
output
R (red)
8, 9. Connecting a satellite tuner, television, or settop box
(VIDEO 3 or 4)
10. Connecting video camera, etc. (VIDEO 5 INPUT)
Using an RCA video cable, connect the video output jack
(composite) of the device to the VIDEO 5 VIDEO jack of the DTR-
7.3. Or if the device has an S video output jack, connect it to the
VIDEO 5 S VIDEO jack of the DTR-7.3 using an S video cable.
Using an RCA video cable, connect the video output jack
(composite) of the device to the VIDEO 3 (or 4) VIDEO IN jack of
the DTR-7.3. Or if the device has an S video output jack, connect it
to the VIDEO 3 (or 4) S VIDEO IN jack of the DTR-7.3 using an S
video cable. Or if the device has component video outputs, connect
them to one of the banks of COMPONENT VIDEO INPUT jacks on
the DTR-7.3.
Using an RCA audio cable, connect the audio output jack of the
device to the VIDEO 5 AUDIO jacks of the DTR-7.3. Make sure that
you properly connect the left channel to the L jack and the right
channel to the R jack.
With the initial settings of the DTR-7.3, the VIDEO 3 and 4 input
sources are set for the COMPONENT VIDEO INPUT 2 jacks.
If the device has an optical digital output, connect it to the VIDEO 5
DIGITAL jack of the DTR-7.3.
If you connect the device to the COMPONENT VIDEO INPUT 1
jacks, this must be changed at Setup Menu → Input Setup → Video
Setup → Component Video (see page 48).
The VIDEO 5 digital input is fixed to the OPTICAL input on the
front panel.
Using an RCA audio cable, connect the audio output jack of the
device to the VIDEO 3 (or 4) AUDIO IN jacks of the DTR-7.3.
Make sure that you properly connect the left channel to the L jack
and the right channel to the R jack.
Front panel
S Video output
If the device has a digital output, connect it to either the DIGITAL
INPUT COAX jack or DIGITAL INPUT OPT jack of the DTR-7.3
depending on the type of connector on the device.
Digital output
(optical)
With the initial settings of the DTR-7.3, the VIDEO 3 input
source is set for digital input at the OPT 3 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page 46).
10. Video camera/ Video game
(VIDEO 5 INPUT)
With the initial settings of the DTR-7.3, the VIDEO 4 input source is
not set for digital input. If you are connecting a digital component,
these settings must be changed at Setup Menu → Input Setup →
Digital Setup (see page 46).
Video output
L
Analog output
R
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting speakers
Before connecting the speakers, it is very important to place them
properly for the optimum sound space for your listening pleasure. Be
sure to refer to the instruction manuals that came with the speakers
during placement and connection. Furthermore, be aware that for
surround playback, the configuration and placement of your
speakers are both very important.
Surround back speakers
• Place these speakers so that their height is 3 feet (1 meter) higher
than that of the listener’s ears.
• When using surround back left and right speakers, place them
behind the listener so that the angles between the lines from each
speaker to the listener and a line straight back from the listener
are less than 30 degrees.
For THX surround EX playback, we recommend that you use a THX
speaker system that is certified by THX Ltd.
10
Ideal speaker configuration
• Front right and left speakers
• Center speaker
Produces a rich sound image by serving as a sound source for the
front right and left speakers and enhancing the sonic movement.
8
9
• Surround right and left speakers
Subwoofer
Adds three-dimensional sonic movement and produces
environmental sound associated with the background and effect
sound for each scene.
When bass sound is reproduced, its volume and quality greatly depend
on subwoofer placement. Those characteristics also depends on the
shape of your listening room as well as your listening point. Generally
speaking, good bass sound is obtained when the subwoofer is placed
in the corner of the room or at one-third the length of the room.
• Surround back right and left speakers
Required for enjoying Dolby Digital EX, THX Surround EX,
DTS-ES Matrix 6.1, or DTS-ES Discrete 6.1 audio.
• Subwoofer
Produces powerful and heavy bass.
corner
Minimum speaker configuration for surround
sound playback
1/3 room length
• Front right and left speakers
• Surround right and left speakers
For optimizing the subwoofer placement, we recommend you to:
The sound recorded for the center speaker and the subwoofer will be
properly distributed to the front right and left speakers for optimized
surround playback.
• play a movie or music source containing good quality base sound,
• take some experimenting while changing subwoofer’s position
in the room, and
• try different positioning until you get the most out of the base
sound while fixing the listening point.
Speaker placement
Layout with dipolar
speakers
Layout with monopolar
speakers
Ideal speaker placement varies depending on the size of your room
and the wall coverings. Here, only typical example of speaker
placement and recommendations are shown.
2
2
1
1
5
3
4
3
5
4
In order to create the optimum conditions for the best sound quality,
be sure to place all the speakers so that the greatest difference
between the distances of each speaker to the listening position is less
than 20 feet (6 meters).
Important points regarding speaker placement
6
7
6
7
10
10
Front left and right speakers and center speaker
• Place these three speakers all at the same height.
• Place each speaker so that it is aimed at the location of the
listener’s ears when at the listening position.
8
9
8
9
1
2
3
4
5
TV or screen
Subwoofer
Front left speaker
Center speaker
6
Surround left speaker
Surround right speaker
Surround back left speaker
Surround back right speaker
Surround left and right speakers
7
8
9
• Place these speakers so that their height is 3 feet (1 meter) higher
than that of the listener’s ears.
Front right speaker
10 Listening position
Most dipoles have an arrow on them to indicate their orientation in
which that should be placed. For the correct acoustical phasing in the
room, dipolar surround speakers should be placed so that their
arrows point forward toward the screen and dipolar surround back
speakers should be placed so that their arrows point to each other.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting speakers
Connecting speakers
Using the speaker labels
After determining the layout of your speaker system, it is now
necessary to connect the speakers correctly to your DTR-7.3.
The positive speaker terminals on the DTR-7.3 are color coded for
easy identification. Attach the supplied speaker labels to the speaker
cables, and then match the colors on the speaker cables to the
corresponding terminals.
Caution:
Connect only speakers with an impedance between 4 and 16 Ω to
the DTR-7.3. If the impedance of even one speaker is between 4
and 6 Ω, be sure to set the speaker impedance setting
accordingly (see page 41).
Speaker cable label
Notes:
DTR-7.3
Speaker
• Even if you are using only one speaker or listening to monaural
(mono) sound, never connect a single speaker in parallel to both
the right and left-channel terminals.
Speaker cable label
SPEAKERS
SPEAKERS
–
+
–
+
The speaker channels are colored as follows:
Front left speaker (+): White
L
L
L
L
Front right speaker (+): Red
Center speaker (+): Green
R
R
R
R
Surround left speaker (+): Blue
–
+
–
+
Surround right speaker (+): Grey
Surround back/Zone 2 left speaker (+): Brown
Surround back/Zone 2 right speaker (+): Tan
• To prevent damage to circuitry,
never short-circuit the positive (+)
and negative (–) speaker wire.
NO!
• Be sure to connect the positive and negative cables for the
speakers properly. If they are mixed up, the left and right signals
will be reversed and the audio will sound unnatural.
• Do not connect more than one speaker cable to one speaker
terminal. Doing so may damage the DTR-7.3.
• Connect either your surround back speakers or the speakers you
will be using in the remote zone (Zone 2) to the SURR BACK
SPEAKERS/ZONE 2 SPEAKERS terminals (see page 24).
Front right
speaker
Front left
speaker
Surround right
speaker
Surround left
speaker
Use the PRE OUT SUBWOOFER
jack to connect a subwoofer with a
built-in power amplifier. If your
subwoofer does not have a built-in
amplifier, connect an amplifier to
the PRE OUT SUBWOOFER jack
and the subwoofer to the amplifier.
Subwoofer
DIGITAL
INPUT
PRE OUT
R
L
COMPONENT
VIDEO
AUDIO
VIDEO
S VIDEO
ANTENNA
FRONT SPEAKERS
SURR SPEAKERS
COAX
FRONT
SUB
OUTPUT
AV RECEIVER
MODEL NO. DTR 7.3
MONITOR
R
L
R
L
OUT
1
2
3
Y
-
R
L
CENTER
AM
OUT
IN
ZONE 2
DVD
PB
AC OUTLETS
SURR
PR
SURR
R
L
BACK/
INPUT 1
Y
ETHERNET
[NET-TUNE]
SURR
Conn
e
cting the speaker cable
CENTER
BACK/
ZONE 2
SPEAKERS
PB
SPEAKER
AC 120V 60Hz
SWITCHED
:
CAUTION
1. Strip away approx. 5/8 inch (15 mm) of
SPEAKER
TOTAL 120W 1A MAX.
R
IMPEDANCE
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
R
L
the wire insulation.
INPUT 2
Y
SEE INSTRUCTION
MANUAL FOR
IR
AC INLET
2.Twist the wire ends tightly together.
A
ZONE 2
12V
TRIGGER OUT
CORRECT SETTINGS.
IN
RS232
P
B
R
3. Unscrew the speaker terminal cap.
4. Insert the exposed wireend.
P
OUT
REMOTE
CONTROL
B
5. Screw down the speaker terminal cap.
1
2
3
4
5
5/8"
(15mm)
Center
speaker
Surround Back Surround Back
right speaker left speaker
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting antennas
To use the tuner of DTR-7.3, it is necessary to prepare the supplied
FM and AM antennas.
Connecting the included antennas
Connecting the FM indoor antenna:
• Adjustment and placement of the FM and AM antennas for
better reception must be done while listening to a station
broadcast.
The FM indoor antenna is for indoor use only. During use, extend the
antenna and adjust its orientation until the clearest signal is received.
Fix it with push pins or similar items in the position that will cause
the least amount of distortion.
If the reception is not very clear with the attached FM indoor
antenna, the use of an outdoor antenna is recommended.
• If better reception cannot be obtained, then placement of an
outside antenna is recommended.
Connecting the AM loop antenna:
Assembling the AM loop antenna
The AM loop antenna is for indoor use only. Set it in the direction
and position where you receive the clearest sound. Put it as far away
as possible from the DTR-7.3, televisions, speaker cables, and power
cords.
Assemble the loop antenna as shown in the illustration.
• Refer to “Connecting the AM loop antenna” below for details on
If the reception is not very clear with the attached AM indoor
antenna, the use of an outdoor antenna is recommended.
how to connect the loop antenna.
(Indoor) AM loop antenna
FM antenna
Insert into the hole.
Australian models
AUDIO
ANTENNA
Connecting the AM antenna cable
1. Press down the lever at the antenna terminal.
2. Insert the wire into the terminal hole.
3. Release the lever.
R
L
CENTER
AM
L
USA and
Canadian
FM
75
models
1
2
3
Strip away the insulation from the end of
the cable, and fully insert the stripped end
of the cable.
Hint:
Either of the split ends of the AM antenna can be connected to either
terminal. Unlike speaker cabling, there is no polarity for AM
broadcast signals.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting antennas
Connecting an FM outdoor antenna
Directional linkage
Make sure to follow the general rules given below:
Do not use the same antenna for both FM and TV (or VCR)
reception since the FM and TV (or VCR) signals can interfere with
each other. If you must use a common FM/TV (or VCR) antenna, use
a directional linkage type splitter.
• Keep the antenna away from noise sources (neon signs, busy
roads, etc.).
• It is dangerous to put the antenna close to power lines. Keep it
well away from power lines, transformers, etc.
• To avoid the risk of lightning and electrical shock, grounding is
necessary. Follow item 14 of the “Important Safeguards” on
page 2 when you install the outdoor antenna.
To receiver
To TV (or VCR)
PRE OUT
AUDIO
R
L
ANTENNA
Connecting the antenna cable to the 75/300 Ω
antenna adapter (Australian models only)
CENTER
AM
R
L
Connecting the 300 Ω ribbon wire:
L
Loosen the screws on the adapter and wrap the wires of the ribbon
wire around these screws. Then tighten the screws down with a
screwdriver.
FM
75
Outdoor
antenna
Connecting an AM outdoor antenna
If reception is poor with the indoor AM antenna, stretch out the
outdoor antenna (16 feet (5 meters) or more) above a window or
outside.
300 Ω
ribbon wire
• Keep the indoor AM loop antenna connected. Do not remove it.
Connecting the coaxial cable:
• To avoid the risk of lightning and electrical shock, grounding is
necessary. Follow item 14 of the “Important Safeguards” on
page 2 when you install the outdoor antenna.
1. With your fingernail, or a small screwdriver, press the
stoppers of the 75/300 Ω antenna adapter outward and
remove the cover.
Outdoor antenna
2. Remove the transformer wire A from slit B and insert it
into slit C.
3. Prepare the coaxial cable as shown in the diagram.
4. Connect the 75/300 Ω antenna adapter to the coaxial
cable.
PRE OUT
AUDIO
R
L
ANTENNA
(Indoor)
AM loop antenna
1. Insert the end of the cable.
2. Clamp it in place with pliers.
CENTER
AM
5. Reinstall the cover.
R
L
1
2
3, 4
R
L
FM
75
6
3
6
mm mm mm
Slit B
5/8"
(15mm)
wire A
Slit C
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the remote zone (Zone 2) speakers
The DTR-7.3 allows you to watch and listen to two separate input
Main Room
Remote Zone (Zone 2)
sources at the same time. This allows you to, for example, place
speakers and a television in two different rooms so that two or more
people can enjoy two different movies at the same time. The room
where the DTR-7.3 is actually located is referred to as the main room
while the separate room is referred to as the remote zone (Zone 2). In
addition, the IR IN/OUT terminal of the DTR-7.3 allows you to
control the DTR-7.3 from the remote zone (Zone 2) with the remote
controller even though the remote zone is physically separated. The
diagram below shows how to make the proper connections for the
remote zone.
PRE OUT
R
L
FRONT
SUB
Zone 2
Left
speaker
Zone 2
Right
speaker
CENTER
SURR
SURR
R
L
BACK/
ZONE
2
When using the SURR BACK/ZONE 2 SPEAKERS
terminals
Left (white)
Right (red)
Power amplifier
If you are using a 5.1-channel speaker system in the main room, you
can connect the speakers for the remote zone (Zone 2) to the open
SURR BACK/ZONE 2 SPEAKERS terminals.
DTR-7.3
With this connection, select “Zone 2” for the Hardware Setup →
Surr Back/Zone2 → Surr Back/Zone 2 setting in the Setup menu (see
page 42).
When using the ZONE 2 OUT terminals
When you have connected all the speakers for 7.1-channel audio in
the main room, connect the speakers as shown below.
Main Room
Remote Zone (Zone 2)
The ZONE 2 OUT terminal is a constant output. Connect to the
LINE input of the amplifier (CD, tape, etc.). Adjust the volume with
the amplifier connected to the ZONE 2 OUT terminal.
Zone 2
Left
Zone 2
Right
speaker
speaker
1. Connect the DTR-7.3 to the amplifier for the remote
zone.
2. Connect the remote zone speaker cables to the
speaker terminals on the amplifier.
SURR
BACK/
ZONE 2
SPEAKERS
3. Connect the DTR-7.3 to the monitor for the remote
zone.
R
L
Remote Zone (Zone 2)
Zone 2
Left speaker
Zone 2 monitor
or projector Right speaker
Zone 2
DTR-7.3
Note:
It is important to be aware of the speaker impedance (see page 41).
When using the SURR BACK/ZONE 2 PRE OUT
terminals
Zone 2 amplifier
If you are using a 5.1-channel speaker system in the main room, you
can connect the amplifier for the remote zone (Zone 2) to the open
SURR BACK/ZONE 2 PRE OUT terminals and connect the remote
zone speakers.
Main Room
AUDIO
VIDEO
S VIDEO
With this connection, select “Zone 2” for the Hardware Setup →
Surr Back/Zone 2 → Surr Back/Zone 2 setting in the Setup menu
(see page 42).
MONITOR
OUT
R
L
OUT
ZONE
2
Right (red)
Left (white)
DTR-7.3
Note:
The ZONE 2 out terminals of the DTR-7.3 are of a fixed output
level.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating components not reached by the
remote controller signals (IR IN/OUT)
In order to use the remote controller to control the DTR-7.3
from a remote location, you will need to prepare a multi-room
kit (sold separately) such as one of those given below:
Make the connection as shown below. Do not plug in any equipment
to the power outlet until all the connections are complete.
• Onkyo’s Multi-Room System kits (IR Remote Controller
Extension System)
from connecting block
Mini plug cable
• Multiroom A/V distribution and control system such as those
from Niles® and Xantech®
If the remote controller signal does not reach the
DTR-7.3 remote sensor
IR
IN
If the DTR-7.3 is located inside a cabinet or other enclosure where
the infrared rays from the remote controller cannot enter, then
operation with the remote controller will not be possible. In such a
case, it will be necessary to install a remote sensor at a location
outside of the cabinet for the infrared rays from the controller can
reach.
OUT
DTR-7.3
If the remote controller signal does not reach
other components
With this connection, select “Main” for the Hardware Setup → IR IN
Setup → Position setting in the Setup Menu (see page 42).
In this situation, you will need to use a commercially available IR
emitter. Connect the mini plug of the IR emitter to the IR OUT
terminal on the DTR-7.3 and then place the IR emitter on the remote
sensor of the component or facing it. When the IR emitter is
connected, only the signal input to the IR IN terminal is output to the
IR OUT terminal. The signal input from the remote sensor on the
front of the DTR-7.3 will not be output to the IR OUT terminal.
Connectiong
block
IR Receiver
IR IN
DTR-7.3
Remote controller
Connectiong
block
IR Receiver
IR IN
In the
cabinet
DTR-7.3
IR OUT
IR Emitter
: Signal flow
Remote controller
The IR IN input allows you to control the DTR-7.3 from the remote
zone (Zone 2) with the remote controller even though the remote
zone may be on the other side of the building from the main zone.
The diagram below shows how to make the proper connections for
the remote zone.
Other
component
: Signal flow
With this connection, select “Zone 2” for the Hardware Setup → IR
IN Setup → Position setting in the Setup Menu (see page 42).
Other component
Emitter
To IR IN
: Signal flow
Remote control
sensor
IR Receiver
IR
DTR-7.3
IN
Connecting
block
Mini plug
OUT
Mini plug cable
DTR-7.3
IR Emitter
Remote controller
Main room
: Signal flow
Zone 2 room
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous Connections
Connections for remote control (
)
Connecting the power cords from other devices
The
Onkyo components equipped with the same
component is connected to the terminal, it can be operated by the
remote controller supplied with the DTR-7.3. In addition, when you
terminal on the DTR-7.3 is for connecting other Integra/
The DTR-7.3 is equipped with AC mains outlets for connecting the
power cords from other devices so that their power is supplied
through the DTR-7.3. By doing this, you can leave the connected
device turned on and have the STANDBY/ON button on the DTR-
7.3 turn on and off the device together with the DTR-7.3.
terminal. When a
connect a component to the
terminal, you can also perform the
system operations given below.
The shape, number, and total capacity of the AC outlets may
differ depending on the area of purchase.
Power on/ready function
When the DTR-7.3 is in the standby state, if an
-connected
Caution:
component is turned on, the DTR-7.3 also turns on and the input
source selected at the DTR-7.3 automatically switches to that
component.
Be aware that this function will not work if the power cord for the
-connected component is connected to the AC OUTLET on the
DTR-7.3, or if the DTR-7.3 has already been turned on.
Make sure that the total capacity of the components connected to the
DTR-7.3 does not exceed the capacity that is printed on the rear
panel (e.g., TOTAL 120W).
Direct change function
When the play button is pressed at an
-connected component, the
input source selected at the DTR-7.3 automatically changes to that
component.
Power off function
When the DTR-7.3 is placed in the standby state, all
-connected
AC OUTLETS
AC 120V 60Hz
components are also automatically put into the standby state.
SWITCHED
TOTAL 120W 1A MAX.
Also, if you press the ON button on the DTR-7.3 remote controller
while the DTR-7.3 is turned on, all
-connected components
(DVD players, CD players, MD recorders, tuners, etc.) are also
turned on.
USA and Canadian
models
DTR-7.3
REMOTE
CONTROL
connector
RS 232 port
The RS 232 port is to be used in conjunction with an external
controller to control the operation of the DTR-7.3 by using an
external device.
Ex: Integra/Onkyo CD
player
connector
Ex: Integra/Onkyo
cassette tape deck
AC INLET
Plug the supplied power cord into this AC INLET and then into the
power outlet on the wall.
To connect components using the
remote control cable from this
other component. An
mm) miniature two-conductor plug comes with every cassette tape
deck, compact disc player, MD recorder, and DVD player that has an
terminal.
terminal, simply connect a
terminal of the
remote control cable with a 1/8-inch (3.5-
• Do not use a power cord other than the one supplied with the
DTR-7.3. The power cord supplied is designed for use with the
DTR-7.3 and should not be used with any other device.
terminal to the
• Never have the power cord disconnected from the DTR-7.3
while the other end is plugged into the wall outlet. Doing so may
cause an electric shock. Always connect by plugging into the
wall outlet last and disconnect by unplugging from the wall
outlet first.
• When performing operations with
using the system, do not use the remote zone (Zone 2).
-connected components
• For remote control operation, the audio connection cables must
also be connected.
• If a component has two
terminals, you can use either one to
connect to the DTR-7.3. The other one can be used to daisy chain
with another component.
AC INLET
• With Integra/Onkyo DVD players, you can enter the pre-
program code so that you can operate the DVD player directly
with the remote controller without connecting the
(see page 65).
terminals
Power cord
(supplied)
To an AC wall
outlet
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous Connections
Connecting to an external device with 12V
TRIGGER terminal
Connecting auxiliary power amplifier
These jacks are for connecting auxiliary power amplifier.
You can use an auxiliary power amplifiers to listen at louder
volumes than you can with the DTR-7.3 alone. When using a power
amplifier, connect each speaker to the power amplifier.
These terminals are provided so that you can use the operation of the
DTR-7.3 control the operation of another externally connected
device. Connect the component to this 1/8-inch mini-jack terminal
and when the set input source is selected, the device will turn on. Set
the 12V TRIGGER terminal using the Setup menu: Input setup →
12V trigger (see page 52).
L
to white
Front
to Red
When the DTR-7.3 is in the ZONE 2 mode, this terminal outputs at
12 V/100 mA.
DIGITAL
INPUT
PRE OUT
R
L
R
COAX
FRONT
SUB
1
CENTER
Subwoofer
to Purple
2
SURR
3
L
Surround
back
to Brown
SURR
Connecting to devices with analog multi channel
output
R
L
BACK/
OPT
ZONE
2
1
to Tan
FRONT
MULTI C
INPUT
R
2
Connect a DVD player, MPEG decoder, or other component that has
a multi channel port for 5.1 channel or 7.1 channel output.
L
to Blue
to Gray
Surround
R
to Green
Center
L
to white
to Red
Front output
DIGITAL
PRE OUT
R
L
INPUT
R
COAX
FRONT
SUB
1
to Purple
Power amplifier
CENTER
Subwoofer
Surround
2
SURR
L
to Blue
3
SURR
R
L
BACK/
OPT
1
ZONE
2
1
2
3
4
5
6
7
8
to Gray
R
FRONT
MULTI
INPUT
L
2
R
SUB
CENTER
Ex: DVD-Audio player/MPEG
decoder
3
1. Front left speaker
2. Front right speaker
3. Subwoofer
4. Surround back left/
ZONE 2 left speaker
5. Surround back right/
ZONE 2 right speaker
6. Surround left speaker
7. Surround right speaker
8. Center speaker
SURR
DIGITAL
OUTPUT
R
L
OPT
SURR
BACK
R
L
to Tan
GND
to Brown
Surround back
Center
to Green
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the power
Standby/On
On
Standby
RCVR
Standby Indicator
To wall outlet
• Before you plug in the DTR-7.3, confirm that all connections
have been made properly.
Memory preservation
The DTR-7.3 does not require memory preservation batteries. A
built-in memory backup system preserves the contents of
memory (e.g., speaker settings and surround settings) during
power failures and even when the unit is unplugged. The unit
must be plugged in order to charge the back-up system.
• Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall outlet
on a different circuit.
The length of time that the memory will be preserved will vary
depending on the ambient climate. On the average, memory
contents are protected over a period of a few weeks after the last
time the unit has been unplugged. This period may be shorter
when the unit is exposed to a highly humid climate.
Turning on the power
1. Plug the power cord into an AC wall outlet.
The STANDBY indicator will light up.
2. Press the Standby/On button to turn on the DTR-7.3.
The display will light up and the Standby
indicator will turn off.
If you press the Standby/On button again,
the receiver returns to Standby state.
Turn off
Turning on the power from the remote controller
Before you can use the remote controller, you must perform steps 1
and 2 above and place the DTR-7.3 in the standby state.
1. Press the RCVR MODE button.
The RCVR MODE button lights.
2. Press the On button to turn on the DTR-7.3 (take it out
of the standby state).
To return the DTR-7.3 to the standby state,
press the Standby button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying music or videos with the DTR-7.3
Input source buttons
Master Volume
RCVR
VOL /
Input Selector
buttons
Tape
Though the DTR-7.3 is often used to listen to the radio, it does not
show you its true ability until it is used to play music or watch
videos, DVDs, and the like. The DTR-7.3 has the latest and most
state-of-the-art features to play back today’s technologies with the
utmost in fidelity and power. From a two-speaker system to a seven-
speaker system, you are assured a sound space that you can always
enjoy.
3. Adjust the volume.
DTR-7.3
Remote controller
To ensure the proper sound space, you must first perform the
speaker setup settings. These settings allow you to set the type of
speakers you are using, the distance that they are located from
the listening position, and the individual speaker volumes. For
more details, see Speaker Setup Sub-menu of the Setup Menu on
page 43.
Adjusting the main volume adjusts the volume level of all the
speakers connected to the DTR-7.3 together. If headphones are
connected, this also adjusts the volume heard from the
headphone speakers. To adjust the volume, either press the VOL
buttons on the remote controller or turn the Master Volume
dial. To increase the volume, turn the dial clockwise; to decrease
the volume, turn the dial counterclockwise. The volume can be
set to Min, 0 to 100 (or –∞, –81 to +18 dB).
Basic operation
If you want to perform these operations using the remote controller,
first press the RCVR button.
1. Press the input source button (or Input Selector
button on the remote controller) that corresponds to
the source to which you want to listen.
To change the display of the input source from
TAPE to MD
If you connected an MD recorder to the TAPE jack on the DTR-7.3,
you can have “MD” appear when the Tape source button is pressed.
DTR-7.3
Changing the display:
Press and hold down the Tape source button until the display
changes from TAPE to MD (approx. 3 seconds).
Remote controller
2. Turn on the corresponding component and play the
media.
To return the display to its original setting, perform the same
procedure.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying music or videos with the DTR-7.3
Sleep
Muting
Phones
Temporarily turning off the sound
Listening with headphones
To turn off the sound momentarily, press the Muting button on the
remote controller. When pressed, “Muting” is displayed on the
DTR-7.3. Press the Muting button again to turn the sound back on.
To listen with headphones, plug a pair of headphones with a standard
stereo plug into the Phones jack on the DTR-7.3 front panel.
When you connect headphones, no sound will be heard from the
speakers.
When the headphones are unplugged, the DTR-7.3 returns to its
original listening mode. When using the headphones, you can only
use the Direct, Stereo, and Mono listening modes. (Available modes
can vary depending on the current input source.)
Remote controller
If you have selected MULTI CH INPUT, you will only hear the
sound only output to the front right and left channels.
The headphone volume level can be adjusted at the Setup Menu (see
page 60).
Adjusting the bass and treble
Note:
You can adjust the bass and treble levels at the Setup Menu → Audio
Adjust Menu → Tone Control Sub-menu (see page 53). This
function only affects the front left and right speakers, center speaker,
and subwoofer. Only the bass level can be adjusted for the
subwoofer (the treble adjustment is not effective). This function will
not work if the Listening mode is set to “Direct” or “Pure Audio”.
The signal to the remote zone (Zone 2) will not be affected by
whether or not headphones are connected.
Using the sleep time (remote controller only)
The Sleep button enables you to set the DTR-7.3 to turn off
automatically after a specified time period. If you press it once, the
DTR-7.3 will turn off after 90 minutes. Each time it is pressed
thereafter, the remaining time until the DTR-7.3 turns off decreases
by 10 minutes (i.e., from 90 to 80 minutes). While, the sleep function
is enabled, you can press the Sleep button to see how much time is
left. If you now press the Sleep button, the remaining time will be
reduced down to the nearest 10 minutes. If it is pressed again, then
the remaining time will be decreased by 10 minutes each time it is
pressed (e.g., if Sleep is pressed with the display reading 54 minutes,
it will be reduced to 50 minutes. If it is pressed again, it will then be
reduced to 40, then 30, and so on). If the Sleep button is pressed
when the time displayed is less than 10 minutes, the sleep function is
cancelled.
If you are using the remote zone (Zone 2), it will turn off at the same
time as the main zone. If you want to set the sleep function for Zone
2 only, set the sleep function with main zone turned on and then put
the main zone into the standby state.
Remote controller
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying music or videos with the DTR-7.3
Pure Audio indicator
Listening mode buttons
Setup Enter
Return
/ / /
Listening
mode
buttons
Input source buttons
• While playing back Analog/PCM sources
Switches from: Pro Logic II Movie → Pro Logic II Music →
DTS Neo6:Cinema → DTS Neo6:Music.
• While playing back D.F. 2-channel sources
Switches from: Pro Logic II Movie → Pro Logic II Music →
DTS Neo6:Cinema → DTS Neo6:Music.
Changing the listening mode
To change the listening mode during playback, press the listening
mode buttons. The functions of the buttons on the DTR-7.3 and
those on the remote controller are the same.
For more information on each listening mode, see pages 50 through
52.
THX: Changes the listening mode to the THX listening mode.
DTR-7.3
If the THX listening mode is selected
• While playing back Dolby Digital sources
Switches the THX Surround EX mode (Auto → On → Off) if the
source is a THX Surround EX-compatible source.
• While playing back Analog/PCM sources
Switches the decoding mode (Pro Logic II Movie → DTS
Neo6:Cinema) for THX processing.
Remote controller
• While playing back DTS sources
Switches the DTS-ES mode from Auto → On → Off. Changing
the DTS-ES mode allows you to enjoy the DTS THX Cinema,
DTS-ES Discrete 6.1 THX Cinema, and DTS-ES Matrix 6.1 THX
Cinema surround systems.
Direct/Pure Audio (Direct): Changes the listening mode for the
signal type that is currently being input from the selected input
source to the Direct listening mode. If pressed, the corresponding
setting in the Listening Mode Preset Sub-menu of the Input Setup
Menu for the selected input source is also changed. When the
listening mode is set to Direct, you can switch between Direct and
Pure Audio. When you select Pure Audio, the video signal is
interrupted (resulting in a blacked-out screen), and the PURE
AUDIO indicator lights up.
Be aware that if surround back speakers are not connected, or if the
Surr Back/Zone 2 setting of the Surr Back/Zone 2 Sub-menu is set to
“Zone 2,” the THX Surround EX, DTS-ES Discrete 6.1, or DTS-ES
Matrix 6.1 listening modes cannot be selected.
DSP
/
: Changes the listening mode for the signal type that is
currently being input from the selected input source as shown below.
Mono
Orchestra
Ch Stereo
Theater-Dimensional
Unplugged
Mono.
Mono Movie
Studio-Mix TV Logic
Enhanced 7
All
Note:
When you are using the remote Zone (Zone 2), the Pure Audio
setting will not work.
If pressed, the corresponding settings in the Listening Mode Preset
Sub-menu of the Setup Menu for the selected input source is also
changed.
Stereo: Changes the listening mode for the signal type that is
currently being input from the selected input source to the Stereo
listening mode. If pressed, the corresponding settings in the
Listening Mode Preset Sub-menu of the Input Setup Menu for the
selected input source is also changed.
All ST: Changes to All Ch Stereo the listening mode for the input
signal of the input source currently selected. If pressed, the
corresponding setting in the Listening Mode Preset Sub-menu of the
Setup Menu for the selected input source is also changed.
Surround (SURR): Changes the listening mode for the signal type
that is currently being input from the selected input source to the
surround mode that matches the signal type (e.g., Dolby Pro Logic
II, Dolby Digital, or DTS). If pressed, the corresponding settings in
the Listening Mode Preset Sub-menu of the Input Setup Menu for
the selected input source is also changed.
If the Surround button is pressed
• While playing back Dolby Digital sources
Switches the Dolby Digial EX setting from: Auto → On → Off.
• While playing back DTS sources
Switches the DTS-ES setting from: Auto → On → Off.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying music or videos with the DTR-7.3
Display Dimmer
RCVR
CH Sel
Test
/
Level
Input source buttons
Dimmer
Display
Switching the display
Adjusting the brightness of the front display
While listening to or watching an input source, you can display the
information regarding the type of source and signal being input by
pressing the Display button on the DTR-7.3 or the remote controller.
You can adjust the brightness of the front display of the DTR-7.3
using the DIMMER button on the remote controller or on the DTR-
7.3 front panel.
DTR-7.3
Remote controller
DTR-7.3
Remote controller
When an input source other than FM or AM is selected:
Input
Temporarily changing the speaker output levels
To change the individual speaker volumes temporarily, follow the
procedure given below. Each channel can be set between –12 and
+12 decibels. The subwoofer can be adjusted between –15 and +12
decibels. Note that the speaker volumes will return to the original
settings when the DTR-7.3 is put in the standby state.
Program format*
Input +
Listening mode
or Multi Ch
1. Press the RCVR Mode button.
* If the input signal does not have a program format, then this will
be skipped.
2. Press the CH Sel button and select
the desired speaker.
* When the input signal is digital audio
The program format is displayed. For example, the display
“Dolby D: 3/2.1” shows that the format is Dolby Digital with 5.1
discrete channels consisting of three front channels (front left,
front right, and center), two surround channels (surround left and
surround right), and the low frequency effect (LFE) channel.
When the front channel number is 2, they are the front left and
front right; when it is 1, it is monaural. When the surround
channel number is 1, it is monaural; when it is 0, there is no
surround channel. When no LFE number is given, there is no
LFE channel. Also, if there is no program format for the input
signal, nothing will be displayed.
3. Press the Level or button to
adjust the volume level.
Notes:
• You cannot select a speaker if it is set to “No” or “None” in the
Speaker Config Sub-menu of the Speaker Setup Menu.
• To have your new speaker levels set here overwrite the settings
at Setup Menu → Speaker Setup Menu → Level Calibration
Sub-menu, press the Test button after you complete step 3 in the
procedure above.
When the input signal is linear PCM
The sampling frequency is displayed. For example, the display
“PCM fs: 44.1k” shows that the signal is PCM and that the
sampling frequency is 44.1 kHz.
When FM or AM is selected as the input source:
FM/AM frequency +
ch
Preset no.
FM/AM +
Listening mode
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying music or videos with the DTR-7.3
Direct/Pure Audio
Master Volume
VOL
Audio Sel
Direct
Input source buttons
Audio Selector
3. Turn on the connected component and start playing
the desired media.
Changing the audio mode
Press the Audio Selector button on the front panel (or Audio Sel
button on the remote controller) to change the audio mode. Each
time the button is pressed, the mode changes from “Auto” →
“Multich” → “Analog” and back to “Auto.” The “Auto” audio mode
is recommended for normal circumstances.
4. If necessary, adjust the output level of each speaker
as desired (see page 32).
Adjust the volume at each speaker so that all the volumes sound
at the same level at the listening position. For the front right,
front left, center, surround right, surround left, surround back
right, and surround back left speakers, the output levels can be
adjusted between –12 and +12 decibels. The subwoofer can be
adjusted between –30 and +12 decibels.
DTR-7.3
Remote controller
Note:
If you change the speaker levels in step 4 above, these new levels for
multichannel sources will have no effect on the settings at Setup Menu
→ Speaker Setup Menu → Level Calibration Sub-menu (see page 45).
Auto (automatic detection): With this setting, the DTR-7.3
automatically detects whether the input signal is digital or analog.
When a digital signal is not input, then the analog signal is played.
This setting only appears if a digital input is selected for the Digital
Input setting at Setup Menu → Input Setup Menu → Digital Setup
Sub-menu (see page 46).
5. Adjust the volume with the Master Volume dial (or the
VOL
buttons on the remote controller.)
DTR-7.3
Remote controller
Multich (Multichannel): Select this setting to play back the input
from the component connected to the MULTI CHANNEL INPUT
port. This setting only appears if “Yes” is selected for the
Multichannel setting at Setup Menu → Input Setup Menu →
Multichannel Setup Sub-menu (see page 47).
Analog: Select this setting to play back the input from a source
component connected to analog audio input jacks. With this setting,
even if a digital signal is input from the same component, only the
analog signal will be output.
Changing the listening mode:
Each time you press the Direct/Pure Audio button on the front panel,
the display changes between “Direct” “Pure Audio.” When
using a remote controller, press Pure A or Direct.
Enjoying the multichannel output
DTR-7.3
Remote controller
Before starting operations, first make sure that the multichannel
connection is properly made and that “Yes” is selected for the
Multichannel setting at Setup Menu → Input Setup Menu →
Multichannel Setup Sub-menu (see page 47).
1. Press the input source button for the component
connected to the MULTI CHANNEL INPUT on the rear
of the DTR-7.3.
Using the tone control:
1. Press the SURROUND button on the front panel (or the
SURR button on the remote controller) to display
“Tone On.”
2. Select “Multich” using the Audio Selector button on
the front panel (or Audio Sel button on the remote
controller).
2. Adjust the tone at Setup Menu → Audio Adjust Menu
→ Tone Control Sub-menu (see page 53).
DTR-7.3
Remote controller
Press the Direct/Pure Audio button on the front panel (or the
Direct button on the remote controller) to turn off the tone
control.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Radio Broadcasts
FM Mode
Tuning
/
Tuner
One of the features of the DTR-7.3 that is most frequently used is its
ability to play FM and AM broadcast radio stations. The DTR-7.3
provides a number of listening modes perfect for listening to the
radio and getting the most out of your audio system. Also, by
presetting radio stations that you listen to frequently, you can select
Listening to a stereo radio station (FM mode)
When you tune into a radio station, TUNED
indicator appears in the display. If you tune into
an FM station in stereo, then “FM STEREO”
appears. If the signal is weak, it may be
impossible to tune into the station in stereo. In
such a case, press the FM Mode button on the
front panel. The AUTO indication disappears
and the radio station is output in the monaural
mode. To return to stereo, press the FM Mode
button again. “AUTO” appears. Some inter-
station noise may be heard, but the sound will
not cut in and out as it would if stereo was
selected.
them easily by pressing the CH
button on the remote controller.
Tuning into a radio station
1. Press the Tuner input source button.
Each time you press the Tuner button, the
input source changes between AM and FM.
Tuning
2. Using the Tuning and buttons
on the front panel, tune into the
station you desire.
Preset
Auto mode
Tuned indicator
Band Frequency
“FM STEREO”
(Lights red)
• The tuner frequency changes in 100-kHz (50-kHz)
increments for FM and 10-kHz (or 9-kHz) increments for
AM.
• You can press the Tuning or button continuously for
more than 0.5 seconds to scan for an FM station in the
direction of the button you pressed (FM auto tuning mode).
After you release the button and a station is received in stereo,
the scanning stops.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Radio Broadcasts
FM Mode
Memory
Preset
/
RCVR
CH
TUN
Tuner
Presetting a radio station
Selecting a preset radio station
1. Tune into the radio station you desire (see “Tuning
into a radio station” ).
1. Press Tuner input source button on
the DTR-7.3 or TUN button on the
remote controller. The front display
should show the currently selected
frequency.
2. Press the MEMORY button on the
front panel.
Tuning
2. Press the Preset
/
buttons and
select the number of the desired
preset station.
ch
Preset
When using the remote controller:
Tuning
3. Using the PRESET
/
buttons,
1. Press the RCVR Mode button.
select a preset number (from 1 to 40)
to assign the station.
The RCVR MODE button lights.
Preset
2. Press the TUN button.
4. Press the MEMORY button to finalize
the procedure.
3. Press the CH
button and select the number of the
desired preset station.
ch
This programs the radio station as a preset radio station.
Erasing a preset radio station
• Up to 40 stations can be stored in memory as preset radio
stations.
1. Press the Tuner input source (or TUN) button and
• You can enter text names for any of the preset radio stations
(see page 49).
press the Preset
/
buttons to select the preset radio
station that you want to erase (see above).
ch
2. Press and hold the Memory button and then press the
FM Mode button.
The selected preset station is erased.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying music in the remote zone
On/Standby
Off
Sleep
Zone 2 indicator
Zone 2
/
Level
Input Selector
buttons
Input source buttons
Zone 2
Using the buttons on the DTR-7.3
Using the remote controller
1. Press the Zone 2 button on the DTR-7.3.
2. Select an input source.
After pressing the Zone 2 button, press the On/Standby
button within 5 seconds.
After pressing the Zone 2 button, you must press an input source
button within 8 seconds.
The indicator above the input source button lights green. In this
condition, even if you change the input source for the main zone,
the input source for the remote zone (Zone 2) will not change.
Select an input source:
After pressing the Zone 2 button, press an Input Selector button
Ex.: When the CD button is pressed.
within 5 seconds.
To select the same source for the remote zone that is selected
for the main zone, press the Zone 2 button again until “Z2
Sel:SOURCE” appears in the display.
In this condition, if you change the input source for the main zone,
the input source for the remote zone (Zone 2) will change as well.
Note:
After you press the Zone 2 button on the remote controller, the
STANDBY indicator on the DTR-7.3 flashes for five seconds.
During this time, you will not be able to perform operations in the
main zone using the remote controller.
When “Z2 Sel:Off” is displayed, the output to the remote
zone is turned off.
Notes:
• If a sleep time is set with the Sleep button, the output to the
remote zone will also turn off when the sleep time elapses.
Adjusting the volume for the remote zone
• The ZONE 2 terminal is an analog output. Digital signals are not
output. If no sound is heard from the selected input source, check
if the component is connected to the analog inputs.
When the remote zone (Zone 2) speakers are connected to the SURR
BACK/ZONE 2 SPEAKERS terminals, or to an amplifier connected
to the SURR BACK/ZONE 2 PRE OUT terminals, adjust the
volume as shown below.
• If the Rec Out button is pressed in the main room while someone is
using the system in the remote zone, the Zone 2 function will be
deactivated and the source will turn off in the remote zone.
Adjusting the volume (using the remote controller):
After pressing the Zone 2 button, the Standby indicator on the DTR-
• If you select FM (or AM) with the input source buttons when the
source for the remote zone (Zone 2) is set to AM (or FM), the
output for the remote zone also changes to AM (or FM).
7.3 will flash for 5 seconds. During this time press the Level
button.
/
• 7.1-channel playback in the main room is disabled if the Surr
Back/Zone 2 setting in the Surr Back/Zone 2 sub-menu of the
Hardware Setup Menu is set to “Zone 2.”
• When you are using the remote zone (Zone 2),
system
operation will not work.
• When you are using the remote zone (Zone 2), the Pure Audio
setting will not work.
Note:
When the remote zone (Zone 2) speakers are connected to the pre-main
amplifier that is connected to the ZONE 2 terminal of the DTR-7.3,
adjust the volume for the remote zone at the pre-main amplifier.
• When you are not using the remote zone (Zone 2), press the
Off button to turn off the Zone 2 indicator. (Using the remote
controller, press the Zone 2 button and then the Standby
button.)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a source
Rec Out
Input source buttons
Notes:
To record the input source signal you are
currently watching or listening to
• If you change the input source during recording, you will record
the signals from the newly selected input source.
This method outputs to the audio and video outputs the currently
selected input source signal. This method allows you to a signal
while you are actually listening to or watching it.
• You cannot record the surround effects.
• Digital signals input to the DIGITAL INPUT (COAX) and
DIGITAL INPUT (OPT) inputs will be output to the DIGITAL
OUTPUT (OPT) output. However, MP3, WMA, WAV, and
other music formats played using Net Audio are only output as
analog audio.
1. Select the input source to record by pressing the
corresponding input source button.
The input source is now selected and you may watch or listen to
it as desired.
• Digital input signals are only output to the digital outputs and
analog input signals are only output from the analog outputs.
There is no conversion from digital to analog or vice versa.
When connecting CD players and other digital components, do
not connect only the digital terminals, but the analog ones as
well.
2. Press the Rec Out button repeatedly until “Rec
Sel:SOURCE” appears in the front display.
The signal from the currently selected input source is now output
to the TAPE OUT, VIDEO 1 OUT, VIDEO 2 OUT outputs for
recording.
• There are some restrictions on recording digital signals. When
making digital recordings, consult the instruction manual that
came with your digital recording equipment (e.g., MD recorder
or DAT deck) to know what restrictions are imposed.
• You cannot record the source connected to the MULTI
CHANNEL INPUT connector.
3. Start recording at the recording component as
desired.
• When listening to music in the remote zone (see previous page),
you can record the music or video that is being played in the
main zone.
To confirm the settings, press the Rec Out button. The current
settings will appear for 8 seconds in the front display.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a source
To record an input source signal different from
that you are currently watching or listening to
Recording the video from one source and the
audio from another
Follow the procedure given below to record an input source signal
different from that which you are listening to or watching at the time
of recording.
You can add the sound from one source to the video of another
source to make your own video recordings.
Below is an example of recording the sound from a compact disc
player connected to CD IN and the video from a video camera
connected to VIDEO 5 INPUT to video cassette tape in a video
cassette recorder connected to the VIDEO 1 OUT jack.
1. Press the Rec Out button.
2. Within 8 seconds, press the input source selector button
of the input source signal that you wish to record.
1. Press the CD input source button.
The signal from the selected input source is now output to the
TAPE OUT, VIDEO 1 OUT, and VIDEO 2 OUT outputs for
recording.
2. Set “VIDEO 5” for the Video setting in the Video Setup
sub-menu of the Setup menu: Input Setup → Video
Setup → Video.
3. Insert a CD in the CD player and insert a tape in the
video camera connected to the VIDEO 5 INPUT.
3. Start recording at the recording component as desired.
4. Insert a video tape for recording in the video cassette
recorder connected to VIDEO 1 OUT.
To confirm the settings, press the Rec Out button. The current
settings will appear for 8 seconds in the front display.
5. Press the Rec Out button repeatedly until “Rec
Sel:SOURCE” appears in the front display.
Notes:
• Be aware that the remote (Zone 2) and recording (REC OUT)
outputs use the same circuit and therefore cannot be used at the
same time.
Now “CD” has been selected as the audio input source and
“VIDEO 5” as the video input source.
• You cannot record the surround effects.
6. Start recording on the video cassette recorder and
start playing at the CD player and video camera as
desired.
• Digital signals input to the DIGITAL INPUT (COAX) and
DIGITAL INPUT (OPT) inputs will be output to the DIGITAL
OUTPUT (OPT) outputs.
• There are some restrictions on recording digital signals. When
making digital recordings, consult the instruction manual that
came with your digital recording equipment (e.g., MD recorder
or DAT deck) to know what restrictions are imposed.
Notes:
• If you change the input source during recording, you will record
the audio signals from the newly selected input source and the
video signals assigned to that input source.
• You cannot record the source connected to the MULTI CH
INPUT connector.
• You cannot record the surround effects.
• You cannot listen to a broadcast from one station while
recording the broadcast from another.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
When making the various settings required to configure your DTR-7.3 for optimum performance, you can either use the OSD Menu that appears
on your television monitor or you can use the display on the front of the DTR-7.3. The OSD Menu is a settings menu that is displayed on your
TV monitor. For your reference when performing the setting procedures, this manual shows both the OSD Menu displayed on your television
monitor and the display on the front of the DTR-7.3.
The Setup Menu consists of the Basic Menu that is divided up into 4 menus, the Hardware Setup Menu, Speaker Setup Menu, Input Setup Menu,
and Audio Adjust Menu, and the Advanced Menu that contains the menus of the Basic Menu plus the Preference Menu, and Network Setup
Menu. These menus are then divided up into various sub-menus, and these contain settings for you to optimize your home theater as you wish.
The display shown below is an example. The actual contents of your display may differ depending on the model of your region and the selected
input source.
0.Hardware Setup
0.Hardware Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.IR IN Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.IR IN Setup
Basic Menu
Your DTR-7.3 is provided with a
Basic Menu for those who are not
familiar with many of the advanced
settings of an AV receiver or those
who wish to watch movies and listen
to music with the minimal amount of
setup. With the Basic Menu, the
settings that rarely need to be set or
that are only needed for advanced
fine-tuning of the sound quality are
not displayed.
|ENTER|Quit:|SETUP|
1.Speaker Setup
|ENTER|Quit:|SETUP|
1.Speaker Setup
1.Speaker Config
1.Speaker Config
2.Speaker Distance
3.Level Calibration
2.Speaker Distance
3.Level Calibration
|ENTER|Quit:|SETUP|
|ENTER|Quit:|SETUP|
Basic Menu
2.Input Setup
Input:DVD
2.Input Setup
Input:DVD
0.Hardware Setup
1.Speaker Setup
2.Input Setup
1.Digital Setup
2.Multichannel Setup
3.Video Setup
4.Character Input
5.IntelliVolume
1.Digital Setup
3.Audio Adjust
2.Multichannel Setup
3.Video Setup
4.Character Input
5.IntelliVolume
→Advanced Menu
6.Listening Mode Preset
7.12V Trigger
|ENTER|Quit:|SETUP|
|ENTER|Quit:|SETUP|
3.Audio Adjust
|ENTER|Quit:|SETUP|
3.Audio Adjust
Note:
The Hardware Setup Menu is accessible from
the Basic Menu at an initial setting. After
brought up on the screen and set any of its
items, the menu is no longer available from the
Basic Menu.
1.Tone Control
1.Tone Control
2.Surround Speakers
3.Sound Effect
4.Delay
2.Surround Speakers
3.Sound Effect
5.LFE Level
6.Mono
7.Theater-Dimensional
8.Surround
→
default
In this case, you can gain access to the menu via
the Advanced Menu.
|ENTER|Quit:|SETUP|
3.Audio Adjust
Advanced Menu
9.THX
The Advanced Menu provides features such as the Listening Mode Presets that allow
you to customize the output sound for movies and music just the way you like and the
AV Sync Setup that allows you to adjust for discrepancies between the video and audio
10.Mono Movie
11.Enhanced 7
12.Orchestra
13.Unplugged
14.Studio-Mix
15.TV Logic
timing. Settings listed with
using the Advanced Menu.
next to their name are settings that can be set
→default
4.Preference
Advanced Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
1.Volume Setup
2.HeadphonesLevel
3.OSD Setup
5.Network Se→tup
Basic Menu
5.Network Setup
4.OSD Position
Refer to the DTR-7.3
“How to enjoy Net-
|ENTER|Quit:|SETUP|
|ENTER|Quit:|SETUP|
1.IP Address
2.Proxy Setup
3.MAC Address
4.Client Setup
Audio”
manual,
instruction
separate
a
volume, for description
of the network-related
settings.
→
Save Setting
|ENTER|Quit:|SETUP|
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
OSD
Advanced Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
1.Speaker Setup
1.Speaker Config
5.Network Se→tup
1-1.Speaker Config
Basic Menu
2.Speaker Distance
3.Level Calibration
a.Subwoofer
b.Front L/R
c.Center
:Yes
|ENTER|Quit:|SETUP|
:Small
:Small
:Small
:Small
d.Surr L/R
e.Surr Back
Front panel
display
|ENTER|Quit:|SETUP|
f.Crossover:80Hz(THX)
Main menu
Quit:|SETUP|
Menu
Sub-menu
Navigating through the Setup Menu
1. Press the Setup button.
The main menu (Advanced Menu or Basic Menu) appears on
your television monitor.
You can change settings in the Setup Menu using the buttons on the
front panel and on the remote controller.
The buttons on the remote controller correspond to those on the
DTR-7.3 as shown below.
2. Using the
and
cursor buttons, select the menu
that you want to enter.
3. Press the Enter button to enter the selected menu.
Button on remote controller
Button on DTR-7.3
The screen for that menu appears.
SETUP
SETUP
4. Use the
and
cursor buttons to select the sub-
menu that you want to enter and press the Enter
button.
Each sub-menu has different settings that can be changed as
desired, and they are all explained in the pages that follow. To
change a setting, first select it using the and cursor buttons,
and then change the setting using the and cursor buttons.
(upper edge of
ENTER button)
UP
(lower edge of
ENTER button)
DOWN
5. Press the Return button to set the new settings and
return to the previous menu screen. Press the Return
button again to return to the main menu.
(left edge of
ENTER button)
LEFT
Note:
Press the setup button to exit the Setup Menu immediately.
(right edge of
ENTER button)
RIGHT
ENTER
ENTER
RETURN
RETURN
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
0-2. Surr Back/Zone 2 Sub-menu
0. Hardware Setup Menu
Advanced Menu
Advanced Menu
0.Hardware Setup
0.Hardware Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.IR IN Setup
0-2.Surr Back/Zone2
a.Surr Back/Zone2
:Surr Back
|ENTER|Quit:|SETUP|
Quit:|SETUP|
The settings within the Hardware Setup Menu will need to be made
before you use your DTR-7.3 for the first time. Once you set the
Speaker Impedance setting of the Hardware Setup Menu, the setting
will not be displayed again when you enter the Basic Menu. To
change the setting at a later date, select the Advanced Menu to
display the Hardware Setup Menu.
a. Surr Back/Zone 2
Zone 2: Select when connecting the speakers for the remote
zone (Zone 2) to the SURR BACK/ZONE 2 PRE OUT or SURR
BACK/ZONE 2 SPEAKERS terminals (for using the internal
amplifier for Zone 2).
Surr Back: Select when connecting the speakers for the Surr
Back to the SURR BACK/ZONE 2 PRE OUT or SURR BACK/
ZONE 2 SPEAKERS terminals (for using the internal amplifier
for the surround back speakers).
0-1. Speaker Impedance Sub-menu
Use this sub-menu to set the impedance level of the DTR-7.3 to
match the specifications of the speakers you are using.
If the impedances of all speakers are between 6 and 16 Ω, select “6
ohms.” If the impedance of even one speaker is between 4 and 6 Ω,
select “4 ohms.”
Note:
The SURR BACK/ZONE 2 PRE OUT and SURR BACK/ZONE
2 SPEAKER terminals
In order to have 7.1-channel playback in the main room, you must set
the Surr Back/Zone 2 setting to “Surr Back.” When set to “Surr
Back,” the surround back signals are output from the SURR BACK/
ZONE 2 PRE OUT and SURR BACK/ZONE 2 SPEAKER
terminals. Connect the surround back speakers to the SURR BACK/
ZONE 2 SPEAKER terminals or to the speakers terminals of the
power amplifier connected to the SURR BACK/ZONE 2 PRE OUT
terminals.
When you are not using the surround back speakers in the main room
and using the internal amplifier to power the speakers for the remote
zone (Zone 2), set the Surr Back/Zone 2 setting to “Zone 2.” When
set to “Zone 2,” the Zone 2 signals are output from the SURR
BACK/ZONE 2 PRE OUT and SURR BACK/ZONE 2 SPEAKER
terminals. Connect the remote zone (Zone 2) speakers to the SURR
BACK/ZONE 2 SPEAKER terminals or to the speakers terminals of
the power amplifier connected to the SURR BACK/ZONE 2 PRE
OUT terminals.
Note:
Before you change this setting, be sure to first lower the volume at
the DTR-7.3 to the minimum level.
Advanced Menu
0.Hardware Setup
0-1.Speaker Impedance
a.Minimum
:6 ohms
Quit:|SETUP|
At this time, the main room is switched to 5.1 channel playback
mode, and therefore you cannot select the THX Surround EX or
DTS-ES, which requires the sound back.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
0-3. IR IN Setup Sub-menu
Advanced Menu
0.Hardware Setup
0-3.IR IN Setup
a.Position
:Main
Quit:|SETUP|
Use this sub-menu when you have a remote control sensor connected
to the IR IN terminal. The setting in this sub-menu tells the DTR-7.3
whether the remote control sensor is being used for operation of the
DTR-7.3 in the main zone or the remote zone (Zone 2).
Main: Select when you are using the remote control sensor for
operation with the remote controller in the main zone.
Zone 2: Select when you are using the remote control sensor for
operation with the remote controller in the remote zone (Zone 2).
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup
1-1. Speaker Config Sub-menu
1. Speaker Setup Menu
After you have installed the DTR-7.3, connected all the components,
and determined the speaker layout, it is now time to perform the
settings in the Speaker Setup Menu for the optimum sound acoustics
for your environment and speaker layout.
Use this sub-menu to enter which speakers are connected and the
size of each speaker.
Advanced Menu
Before you perform the following settings, it is important that you
first determine the following items:
1.Speaker Setup
• The types and sizes of the speakers that are connected.
1-1.SpeakerConfig
a.Subwoofer:Yes
• The distance from each speaker to the normal listening position.
b.Front L/R
c.Center
:Small
:Small
:Small
:Small
Advanced Menu
d.Surr L/R
e.Surr Back
f.Crossover:80Hz(THX)
1.Speaker Setup
Quit:|SETUP|
1.Speaker Config
2.Speaker Distance
3.Level Calibration
a. Subwoofer
|ENTER|Quit:|SETUP|
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
b. Front L/R
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
Memo:
• If “No” is selected for the Subwoofer setting, this setting is
fixed to “Large.”
Monitor
SW
Center
[
Front
Front
c. Center
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
[
]
]
m/ft
[
m/ft
[
]
m/ft
]
m/ft
• If “Small” is selected for the Front setting, “Large” cannot be
selected for this setting.
SL
SR
[
]
[
]
d. Surr L/R
m/ft
m/ft
None: Select if no surround left and right speakers are
connected.
[
]
[
]
m/ft
m/ft
SBL
Large: Select if the surround left and right speakers are large sized.
Small: Select if the surround left and right speakers are small sized.
SBR
• If “Small” is selected for the Front setting, “Large” cannot be
selected for this setting.
Note:
e. Surr Back
When “Large” is set, the complete frequency range for that speaker
channel will be output. When “Small” is set, the frequencies below
80 Hz for that speaker channel are output to the subwoofer. If there is
no subwoofer, then they will be output to the left and right front
speakers. (Set all speakers for THX speaker systems to “small.”)
None: Select if no surround back left and right speakers are connected.
Large: Select if the surround back left and right speakers are large sized.
Small: Select if the surround back left and right speakers are
small sized.
• If “None” is selected for the Surround L/R setting, this setting
will not appear.
• If “Small” is selected for the Surround L/R setting, “Large”
cannot be selected for this setting.
• If the Surr Back/Zone 2 setting in the Surr Back/Zone 2 Sub-
menu of the Hardware Setup Menu is set to “Zone 2,” this
setting will not appear.
f. Crossover
This setting allows you to set the crossover frequency for your
speaker system. The crossover frequency is the minimum frequency
delivered to a speaker and can be set to 40 Hz, 60 Hz, 80 Hz (THX),
100 Hz, or 120 Hz. Select “80Hz (THX)” if you are using a THX-
certified speaker system. This setting is valid when “Subwoofer” is
set to “Yes,” or for speakers that are set to “Small,” at the “Speaker
Config” menu. Frequencies below this are cut from speakers set to
“Small” and sent to the subwoofer (or to speakers set to “Large”).
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup
h. Subwoofer
1-2. Speaker Distance Sub-menu
Set the distance from the subwoofer to your normal listening
position. This can be set between 1 and 30 feet in 0.5-feet increments
(between 0.3 and 9 meters in 0.15-meter increments).
Use this sub-menu to enter the distance from each speaker to the
normal listening position.
Notes:
• Speakers that you selected “No” or “None” for in the Speaker
Config Sub-menu will not appear in this sub-menu.
• The difference between the distances of different speakers
cannot be set to more than 20 feet (6 meters).
Advanced Menu
1.Speaker Setup
1-2.Speaker Distance
a.Unit
b.Front L/R
c.Center
:feet
:12.0ft
:12.0ft
d.Surr Right : 7.0ft
e.Surr Back R : 7.0ft
f.Surr Back L : 7.0ft
g.Surr Left
h.Subwoofer
: 7.0ft
:12.0ft
Quit:|SETUP|
a. Unit
feet: Select if you will enter the distances in feet.
meters: Select if you will enter the distances in meters.
b. Front L/R
Set the distance from the front left and right speakers to your normal
listening position. This can be set between 1 and 30 feet in 0.5-feet
increments (between 0.3 and 9 meters in 0.15-meter increments).
Position the front left and right speakers so that they are the same
distance from the listener. If they are not, you may lose the center
orientation with stereo sound.
c. Center
Set the distance from the center speaker to your normal listening
position. This can be set between 1 and 30 feet in 0.5-feet increments
(between 0.3 and 9 meters in 0.15-meter increments).
d. Surr Right
Set the distance from the surround right speaker to your normal
listening position. This can be set between 1 and 30 feet in 0.5-feet
increments (between 0.3 and 9 meters in 0.15-meter increments).
e. Surr Back R
Set the distance from the surround back right speaker to your normal
listening position. This can be set between 1 and 30 feet in 0.5-feet
increments (between 0.3 and 9 meters in 0.15-meter increments).
f. Surr Back L
Set the distance from the surround back left speaker to your normal
listening position. This can be set between 1 and 30 feet in 0.5-feet
increments (between 0.3 and 9 meters in 0.15-meter increments).
Note:
If the Surr Back/Zone 2 setting in the Surr Back/Zone 2 Sub-menu of
the Hardware Setup Menu is set to “Zone 2,” then the Surr Bk R and
Surr Bk L settings will not be displayed.
g. Surr Left
Set the distance from the surround left speaker to your normal
listening position. This can be set between 1 and 30 feet in 0.5-feet
increments (between 0.3 and 9 meters in 0.15-meter increments).
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup
a. Left
1-3. Level Calibration Sub-menu
Sound comes from the front left speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
Use this sub-menu to set the volume for each speaker so that each
volume is heard by the listener at the same level. This is especially
important for speaker layouts where the left and right speakers are at
different distances or in asymmetrical positions due to room designs
and configurations. These settings and the distance settings
performed in the Speaker Distance Sub-menu are vital to create the
proper sound space and dynamics.
b. Center
Sound comes from the center speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
c. Right
Sound comes from the front right speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
Note:
The speaker level settings here are not effective for multi-channel
input sources. To adjust the speaker levels for multi-channel input
sources, you will need to use the CH Sel, Level , and Level
buttons on the RC-514M remote controller. See page 33.
d. Surr Right
Sound comes from the surround right speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel increments.
e. Surr Back R
Sound comes from the surround back right speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel increments.
Advanced Menu
1.Speaker Setup
f. Surr Back L
Sound comes from the surround back left speaker. Adjust the sound
level between –12 and 12 decibels in 1-decibel increments.
1-3.Level Calibration
a.Left
: 0dB
: 0dB
: 0dB
: 0dB
Note:
b.Center
c.Right
If the Surr Back/Zone 2 setting in the Surr Back/Zone 2 Sub-menu of
the Hardware Setup Menu is set to “Zone 2,” then the Surr Bk R and
Surr Bk L settings will not be displayed.
d.Surr Right
e.Surr Back R : 0dB
f.Surr Back L : 0dB
g.Surr Left
h.Subwoofer
: 0dB
: 0dB
Quit:|SETUP|
g. Surr Left
Sound comes from the surround left speaker. Adjust the sound level
between –12 and 12 decibels in 1-decibel increments.
h. Subwoofer
Sound comes from the subwoofer. Adjust the sound level between
–15 and 12 decibels in 1-decibel increments.
Calibrating the speaker levels
(1) When this sub-menu is entered, the DTR-7.3 will emit a pink
noise from the front left speaker. At this time, the volume of the
pink noise will automatically increase to a predetermined
reference level (0dB). Remember the volume level of this noise
Using the remote controller
1. Press the Test button.
and then press the
adjusted in 1-decibel increments.) The DTR-7.3 will now emit
the pink noise from the center speaker.
cursor button. (Note that this can be
You will hear a pink noise will be emitted
from the front left speaker.
(1) Remember the volume level of this noise
and then press the CH Sel button. The DTR-
7.3 will now emit the pink noise from the
center speaker.
(2) Using the and cursor buttons, adjust the volume level of the
noise from the center speaker so that it is at the same level as that
was emitted from the front left speaker. You can jog back and
forth between the speakers to help you compare the volume
levels.
(2) Using the Level
/
buttons, adjust the
volume level of the noise from the center
speaker so that it is at the same level as that
that was emitted from the front left speaker.
(3) Press the cursor button again. The DTR-7.3 will now emit the
pink noise from the front right speaker.
(4) Repeat steps (2) and (3) above for the front right and other
speakers until all speakers are adjusted to the same volume level.
(3) Press the CH Sel button again. The DTR-7.3 will now emit the
pink noise from the front right speaker.
Notes:
Use the Level
/
buttons to adjust the volume of the noise
• Speakers that you selected “No” or “None” for in the Speaker
Config Sub-menu will not appear.
from the front left speaker so that it is the same level as that that
was emitted from the center speaker. The pink noise level can be
adjusted in 1-decibel increments.
• To accurately set the output levels, it is recommended to use a
handheld sound pressure level (SPL) meter. Set the meter to C-
weighting and slow averaging. A Radio Shack® SPL meter or
equivalent is recommended. Using the internal channel noise
generators, set each channel so that you read a 75 decibel sound
pressure level.
(4) Use the CH Sel button to select other speakers and adjust the
volumes until all speakers are adjusted to the same level.
2. Press the Test button to complete
the procedure.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
2-1. Digital Setup Sub-menu (When NET AUDIO
is not selected as the input source)
2. Input Setup Menu
This menu allows you to make the various settings concerning the
signals input from the various input sources that you use with the
DTR-7.3. The settings made in this menu are valid for the input
source that is currently selected with the input source buttons at the
front panel and, therefore, these settings are made separately for each
input source. Each input source may have a great number of settings
that are difficult to keep track of, so we recommend making a chart
to record what you have set and for which component to prevent
confusion later.
This sub-menu concerns the input of digital signals from input
sources and if these settings are incorrectly made, the digital audio
signals may not be properly output, or not heard at all. This sub-
menu will not appear if the selected input source button is AM or
FM. It cannot be accessible if “Yes” is selected in 2-2. Multichannel
Setup Sub-menu and “Multichannel” is selected in the Audio
Selector. Also, since Video 5 is fixed to the optical digital terminal
on the front panel, this sub-menu will not appear if Video 5 is
selected.
When Net Audio is not selected as the input source
Advanced Menu
Advanced Menu
2.Input Setup
Input:DVD
2.Input Setup
Input:DVD
2-1.Digital Setup
Input:DVD
1.Digital Setup
2.Multichannel Setup
3.Video Setup
a.Digital Input
:COAX1
4.Character Input
5.IntelliVolume
6.Listening Mode Preset
7.12V Trigger
b.Digital Format
:All
|ENTER|Quit:|SETUP|
Quit:|SETUP|
Initial settings for each input source
Input source
CD
Digital input
OPT 1
PHONO
TUNER
TAPE
----
OPT 2
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
DVD
COAX 2
COAX 3
OPT 3
----
OPTICAL on front panel (fixed)
COAX 1
NET AUDIO
---- : Available for digital input but not set in initial settings.
: Not available for digital input.
a. Digital Input
This setting tells the DTR-7.3 which input source button on the front
panel is connected with which digital input jack on the rear panel. To
perform this setting, you must first select a digital input source at the
front panel and then set the name of the digital input jack it is
connected to with this setting.
For example, if the input source selected at the front panel is CD and
the compact disc player is connected to DIGITAL INPUT OPT 1,
then select “OPT1” here. If the input source selected is not connected
to a digital input, then select “----.”
OPT1-3: Select if the input source is connected to any of the
DIGITAL INPUT OPT jacks 1 through 3.
COAX1-3: Select if the input source is connected to any of the
DIGITAL INPUT COAX jacks 1 through 3.
----: Select if the input source is not from a digital input jack.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
b. Digital Format
Sets the digital signal type to which priority is given during signal
detection at the selected digital terminal.
2-2. Multichannel Setup Sub-menu (When NET
AUDIO is not selected as the input source)
The default setting is “All.” If “----” is selected for this input source
at the Digital Input setting, then this setting will not appear.
Although you can use this default setting as is, you may change it as
desired depending on the input signal format or if you know that you
will always be listening to a certain input signal format from a
particular input source.
When any input source other than Net Audio is selected, this sub-
menu appears and allows you to set the multichannel input setting.
The setting in this sub-menu is normally set to “No,” and only needs
to be changed to “Yes” if a DVD player, MPEG decoder, or other
component that has a multi channel port is connected to the MULTI
CHANNEL INPUT port for 5.1-channel, 6.1-channel, or 7.1-
channel audio. For example, if a DVD player is connected to the
MULTI CHANNEL INPUT port, then select DVD at the front panel
as the input source, bring up this sub-menu, and select “Yes” for the
Multichannel setting. You can only select Multichannel with the
Audio Selector button when “Yes” is selected here.
All: Select for automatic detection of the input signal format.
The input signal format (Dolby Digital, DTS, PCM or Analog)
used by the selected input source is detected automatically to
execute the required decoding process.
DTS: Select for DTS signal processing. The decoding process is
executed only when DTS signals are input.
Advanced Menu
PCM: Select for PCM signal processing. The decoding process
is executed only when PCM signals are input.
2.Input Setup
Input:DVD
Notes:
2-2.Multichannel Setup
Input:DVD
• If “All” is selected and a compact disc or LD is fast-forwarded
during playback, decoded PCM signals may produce a skipping
sound. In such cases, change the setting to “PCM.”
a.Multichannel :Yes
• If a DTS signal is not input when “DTS” is selected, the DTR-
7.3 will not automatically switch to analog output even though
“Auto” is selected with the AUDIO SELECTOR button.
Quit:|SETUP|
Notes on DTS:
• If you play a DTS-formatted CD or LD when the “PCM” setting
is selected on the DTR-7.3, the DTS encoded signal will not be
decoded and noise will be output. This noise could damage the
amplifier and speakers. Therefore, be sure to select “All” or
“DTS” and use the digital input jacks (OPTICAL or COAXIAL)
to connect the DTS source.
Input source selected
CD
Multichannel
No
No
No
No
Yes
No
No
No
No
No
No
PHONO
• If you play a DTS-formatted CD or LD when “All” is selected,
you may hear a noise for a short while until the DTS decoder
recognizes the DTS-encoded signal and starts operating. This is
not a malfunction.
TUNER
TAPE
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
NETAUDIO
• If you press the PAUSE or SKIP button on the player while
playing a DTS source, a short noise may be heard. This is not a
malfunction. In such cases, try playing the source in the “DTS”
selected.
• The DTS indicator on the DTR-7.3 lights while a DTS source is
played. When playback finishes and the DTS signal
transmission stops, the DTR-7.3 remains in DTS mode and the
DTS indicator remains lit. This prevents noise when you operate
the PAUSE or SKIP button on the player. Therefore, if the
source is immediately switched from DTS to PCM, the PCM
signal may not be played. In this case, stop the playback of the
source on the player for about three seconds and then resume
playback.
Notes:
• When playing a device connected to the MULTI CHANNEL
INPUT terminal, be sure to select “Multich” with the Audio
Selector button on the front panel.
• Changing this setting to “No” while playing in the Multichannel
setting will switch the audio mode with Audio Selector to
“Analog.”
• You may not be able to play some DTS source signals from
certain CD players and LD players even when you connect the
player to the DTR-7.3 digitally. This is because the digital signal
has been processed (such as the output level, sampling
frequency, or frequency response) and the DTR-7.3 cannot
recognize the signal as DTS data. Therefore you may hear noise
when you play a DTS source while processing the signal.
• The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, and TAPE
OUT output analog audio signals. Do not record from CDs or
LDs that support DTS using these outputs. If you do, the DTS-
encoded signal will be recorded as noise.
• If a CD or LD encoded in the DTS format is played back with
“PCM” selected, only noise will be produced. Always select
“All” or “DTS” when playing back DTS-encoded sources.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
b. Component Video
2-3. Video Setup Sub-menu
If the video signal from a component is input to one of the
COMPONENT VIDEO input banks (1 or 2), then which input
source and which component video input bank must be set here.
Advanced Menu
The default settings are given below.
2.Input Setup
Input:DVD
Input source selected
CD
Component video input
Last Valid
Last Valid
Last Valid
Last Valid
INPUT 1
2-3.Video Setup
Input:DVD
PHONO
a.Video
:DVD
TUNER
TAPE
b.Component Video
:INPUT1
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
NETAUDIO
INPUT 2
INPUT 2
Quit:|SETUP|
INPUT 2
INPUT 2
INPUT 2
Last Valid
a. Video
This setting allows you to match the audio from one component with
the video from another. Therefore, you can set a video source to be
displayed while the audio from another input source is heard. For
example, this allows you to play the music from a compact disc,
while displaying the picture from a video cassette player or other
video source.
Last Valid (enables the source last selected): Select to have
the video of the previous input source continued.
The default settings are given below.
Input source selected
CD
Video
Last Valid
Last Valid
Last Valid
Last Valid
DVD
PHONO
TUNER
TAPE
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
NETAUDIO
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
Last Valid
Last Valid: Select to have the video of the previous input source
continued. For example, if the selected input source is VIDEO 1,
and you then change to CD (set to “Last Valid”), then the audio
from the CD input is played while the video from VIDEO 1
continues.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
Once 10 characters are entered, you will automatically return to the
previous screen. If the name is completed before you enter 10
characters, enter spaces until 10 characters are entered.
2-4. Character Input Sub-menu
This sub-menu allows you to give names to the stations you have
preset for the AM/FM tuner, and to the input sources you have
connected (excluding the tuner itself). Up to 10 characters can be
entered for each name. For example, if you have a DVD connected to
the VIDEO4 jack, then you can give it the name “DVD2.” Or, if you
have multiple VCRs connected, you can enter the model names or
manufacturer names for each one so that you do not have to
remember which is connected to which input source.
To change an existing character, move the cursor backward with the
Return button or forward with the Enter button to the location of the
mistaken character and then enter the desired character as explained
above. To erase a character, enter a blank space in its place. After
you have completed the name, press the Enter button until you return
to the Character Input Sub-menu.
If you want to enter a name for a preset broadcast radio station, select
the station that you want to name and enter the name.
2-5. IntelliVolume Sub-menu
Advanced Menu
This sub-menu allows you to adjust for the volume differences
between your various input source components.
2.Input Setup
Input:DVD
2-5.Character Input
Input:DVD
Advanced Menu
2.Input Setup
Input:DVD
a.Character Display
:No
b.Character
:
2-6.IntelliVolume Setup
Input:DVD
Press
to edit.
to clear.
a.IntelliVolume
: 0dB
Quit:|SETUP|
Quit:|SETUP|
a. Character Display
Use this setting to select whether or not to display a custom name
when the current input source is selected.
Yes: Select to have your custom name displayed.
No: Select to have the default name displayed.
a. IntelliVolume
When switching input sources, you may find that the output level for
different components or input sources connected to the DTR-7.3 is
different even though the main volume setting is the same. Under
normal circumstances, you would then have to change the volume
setting each time you change the input source. This Intelli Volume
setting allows you to preset a volume level for each input source
separately so that when you do switch from one input source to
another, the DTR-7.3 adjusts the volume accordingly and the
volume stays the same. To set the Intelli Volume, simply select an
input source at the front panel, and if that source is quieter than other
sources, increase its decibel level with the cursor button, or if it is
louder than other sources, decrease its decibel level with the cursor
button.
b. Character
If you have selected “Yes” for the Character Display above, then
here you can enter the name that you want to display. Press the
cursor button to clear the current entry. Press the cursor button to
bring up the Character Input screen.
Advanced Menu
2.Input Setup
Input:DVD
2-5.Character Input
Input:DVD
b.Character
The Intelli Volume can be adjusted between –12 and +12 decibels.
:
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
|ENTER| 0123456789-.’
Back:
|RETURN|
()+*/=,:;!?_
Note:
If you are using the front display and not the OSD Menu, press the
button when “Chr: ” appears in the front display. Then “ABCDEF..”
appears. This is the Character Input screen. The cursor buttons will
allow you to navigate through this screen just as they would if you
were using the OSD Menu so you will need to refer to the figure
below for the actual layout of the Character Input screen.
At the Character Input screen, press the cursor buttons to move the
cursor to the desired character and then press the ENTER button.
The characters entered will appear in order in the 10-character space
field above.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
* The 5.1-channel digital surround format has a variety of versions
including Dolby Digital and DTS. The 5.1- channel digital
surround format enables the individual recording and playing of
five full-range (20 Hz to 20 kHz) channels (left and right front,
center, and two surround channels) plus an LFE channel (Low
Frequency Effect) for the low-range effect sound. It will create a
realistic sound that can be heard in the theaters and concert halls.
2-6. Listening Mode Preset Sub-menu
With the DTR-7.3, you can set a different listening mode for each
different signal type that comes from each input source. For
example, if your DVD player also plays compact discs and the DVD
video signal is Dolby Digital and the compact disc signal is PCM,
then you can set a different listening mode for each.
This is especially convenient if you frequently play the same types of
movies or music.
Advanced Menu
2.Input Setup
Input:DVD
2-4.ListeningMode Preset
Input:DVD
a.Analog/PCM
:Stereo
b.PCM fs=96k :Stereo
c.Dolby D :Dolby D
d.DTS
e.D.F.2ch
:PLII
f.D.F.Mono:Mono
:DTS
Quit:|SETUP|
Relationship between input source and listening mode
Listening modes marked with the “G” can be selected. For columns that list a number of listening modes, the display will correspond to the
format of the signal from the source media.
Input source signal (display)
Type of software
a. Analog/PCM
(2ch)
b. PCM fs=96k
(2ch)
c. Dolby D
d. DTS
e. D.F.2ch
f. D.F.Mono
(Digital Format
Multichannel)
(Digital Format
Multichannel)
(Digital Format 2ch) (Digital Format Mono)
Tape, Video tape,
Vinyl, Tuner, CD,
MD, DVD (Stereo),
LD, Digital Satellite
DVD
(96 kHz/24 bit)
DVD
Digital Satellite
CD, LD
DVD
DVD
Digital Satellite
DVD
Listening Mode
Mono
G
G
G
G
G
G
Direct/Pure Audio
Stereo
G
G
G
G
G
G
G
G*1
G
G*2
G*3
T-D (Theater-Dimensional)
Dolby Digital
DTS
G*2
G*3
DTS
DTS-ES Matrix 6.1
DTS-ES Discrete 6.1
DTS 96/24
Dolby EX
Dolby Digital EX
Dolby Pro Logic II
DTS Neo:6
PL II Movie
PL II Music
PL II Movie
PL II Music
PL II Movie
PL II Music
DTS Neo:6 Cinema
DTS Neo:6 Music
DTS Neo:6 Cinema
DTS Neo:6 Music
THX
THX Cinema
THX Cinema
THX Cinema
THX Cinema
THX Surround EX
Mono Movie
Enhanced 7
Orchestra
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Unplugged
Studio-Mix
TV Logic
All Ch Stereo
*1 When playing sources recorded in DTS 96/24 format, “DTS 96/24 Stereo” is displayed.
*2 Enables for Dolby Digital input source.
*3 Enables for DTS input source.
Note:
You may not be able to select all the listening modes shown here depending on your speaker configuration or the selected input source.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
Pure Audio
Input source signals
Same as the direct mode except that the pure audio mode also turns
off the display window, turns off the power supply to the video
circuitry, and minimizes the sources of noise. The result is high-
fidelity music playback true to the original source.
a. Analog/PCM
Analog sources consist of LP records, FM and AM broadcasts,
cassette tapes, and the such. PCM (Pulse Code Modulation) is one
form of digital audio signals and is recorded directly onto compact
discs and DVDs without compression.
Note that if you connect a device to the COMPONENT VIDEO
INPUT 2 jacks of the DTR-7.3, the relay switch doesn’t activate and
signals are output to the COMPONENT VIDEO OUTPUT jacks.
Therefore, the display on the monitor connected to the
COMPONENT VIDEO OUTPUT jacks will not disappear.
b. PCM fs=96k
Digital PCM sources recorded with a sampling rate of 96 kHz.
c. Dolby D (Dolby Digital)
Dolby Digital is compressed digital data with a maximum 5.1-
channel surround output. This source signal comes from DVDs and
Stereo
This mode has all input sound is output from the left and right front
speakers.
The subwoofer is also used for playback.
LDs that have the
mark and therefore recorded for 5.1-channel
output. This source also comes from digital satellite broadcasts that
support Dolby Digital.
T-D (Theater-Dimensional)
Dialog norm
For the best enjoyment of your home theater, it is recommended that
you have front left and right speakers, a center speaker, and surround
left and right speakers. However, if you only have front left and right
speakers, you can enjoy multichannel audio by using this mode.
Dialogue Normalization (Dialog Norm) is feature of Dolby
Digital. When playing back software that has been encoded in
Dolby Digital, sometimes you may see a brief message in the
front panel display that reads Dialog Norm xdB (“x” being a
numeric value). Dialogue Normalization serves to let you know
if the source material has been recorded at a higher or lower level
than usual. This data is automatically used by the Dolby Digital
decoder to adjust the output volume of the source material
without affecting the volume of your amplifier. Therefore, even
if source material volume changes, you will not have to adjust
the volume on your amplifier.
This mode controls the characteristics of the sound that reaches each
ear to reproduce a multi-speaker setup. To receive the full effect,
there is an optimum listening position (sweet spot). Refer to the
explanation of the listening angle (see page 55). In addition, if the
reflective sound components are large, it may be difficult to achieve
the desired result, so be sure to set up your system and listening
position to minimize reflective sound.
Dolby Pro Logic II
Opposed to Dolby Pro Logic, which had four channels (front, left,
center, and surround) recorded into two channels with matrix
processing and then played back in four channels, Dolby Pro Logic
II uses a feedback logic circuit to have 5.1-channel surround audio
(Dolby Surround, etc.) matrix-encoded into two channels and then
played back in its original 5.1-channel form.
Dolby Pro Logic II provides a Movie mode designed for playing
movies and a Music mode designed for listening to music. In the
Movie mode, the surround channels, which used to provide
monaural output over only a narrow frequency range, now provide
complete stereo output over the full frequency range. The result is
movie viewing with a realistic feel of movement. The Music mode
uses the surround channels to provide a natural soundfield that
cannot be provided with normal stereo output.
d. DTS
DTS (Digital Theater System) is compressed digital data with a
maximum 5.1-channel surround output (6.1-channel with DTS-ES
Discrete sources) that allows for an extremely high-quality sound.
This source signal requires a DVD player that supports DTS output
and comes from DVDs, compact discs, and LDs that have the
mark.
e. D.F. 2 ch (Digital Format 2 channel)
2-channel digital signals (not including PCM) such as Dolby Digital.
DVDs or LDs recorded with 2-channel sound may be this type of
input signal.
This mode can be used with VHS and DVD videos with the
mark and certain television programs. The Music mode
can be used with music compact discs and other stereo sources.
f. D.F. Mono (Digital Format Monaural)
Monaural digital signals (not including PCM) such as Dolby Digital.
DVDs or LDs recorded with monaural sound may be this type of
input signal.
Dolby D (Dolby Digital)
This mode is used for playing Dolby Digital sources.
Listening Modes
• Dolby Digital EX
Enabled when playing back sources with surround tracks that
were encoded using the Surround EX technology.
Mono
This mode is for playing old movies where the sound is recorded in
monaural or for playing the left and right channels of movies
separately that contain different language signals. This mode also
allows you to listen to the multiplexed soundtracks on DVDs, and
other media that have them.
• Dolby EX
Select to achieve the same effects as Dolby Digital EX encoded
sources with non-Dolby Digital sources.
Direct
This mode delivers pure sound with minimum sound quality
adjustment and filtration. The sound recorded for the right and left
front channels is output to the right and left front speakers only and
not output to the subwoofer.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Setup
DTS Neo:6
Mono Movie
This mode is suitable for playing back monaural recording such as old
movie soundtracks. The center channel delivers the unprocessed
original sound, whereas the other channels deliver the center-channel
sound processed with the appropriate reverberation. This allows you
to enjoy monaural sound with the atmosphere of a movie theater.
This mode is for 6.1-channel playback of sources such as PCM or
analog sources that have only two channels. The outputs of all six
channels are a wide frequency range with a great separation between
the different channels.
This mode can be set to the Cinema mode designed for playing
movies and the Music mode designed for listening to music.
Enhanced 7
The Cinema mode is good for movies. The reproduced surround
sound provide the same realistic feel of movement as 6.1-channel
sources. This mode can be used with VHS and television programs
with stereo sound.
This mode reproduces a natural surround environment by using seven
speaker channels. The sound effects moving smoothly toward the
surround back. This mode is good for music and TV sports programs.
Orchestra
The Music mode uses the surround channels to provide a natural
sound space that cannot be provided with normal stereo output. This
mode can be used with music CDs and other stereo sources.
This mode is appropriate for classical and opera music. The center
channel is cut and the surround channels are emphasized to widen
the stereo image. It will simulate the natural reverberation that is
created in large halls.
DTS
This mode is used for playing DTS source.
Unplugged
This mode is suitable for acoustical instrumental sounds, vocals, and
jazz music. By emphasizing the front stereo image, it will simulate
the acoustics that you would experience in front of the stage.
DTS-ES Discrete 6.1
With the addition of the surround back channel, this new format has
all 6.1 channels recorded independently for a completely discrete
digital format. Since all channels are recorded independently, high-
fidelity surround playback with the increased feeling of a separated
sound space is achieved.
Studio-Mix
This mode is for rock and popular music. The lively sounds are
enhanced for a powerful acoustic image that simulates the feeling of
being in a club or rock concert.
DTS-ES Matrix 6.1
This format has the surround back channel matrix encoded and
inserted into the left and right surround channels so that at playback
the output for the left, right, and back surround channels are decoded
using a high-precision matrix decoder.
TV Logic
This mode gives realistic acoustics to TV programs that are aired
from TV studios. It enhances the entire surround sound and clarity of
the conversation.
DTS 96/24
All Ch Stereo
Automatically changes to this mode when playing back sources with
This mode is designed for playing background music. The front,
surround, and surround back channels create a stereo image that
encompasses the entire area.
surround tracks that were encoded using the DTS 96/24 technology.
THX
This mode is for playing back sources recorded in the THX format.
For the utmost in fidelity when playing back THX sources, it is also
recommended to use a THX-certified speaker system.
2-7. 12V Trigger Setup Sub-menu
• THX Cinema
This is the conventional 5.1-channel THX format. This mode
should be used only when playing back sources that were mixed
for playback in large movie theater environments.
Advanced Menu
2.Input Setup
Input:DVD
• THX Surround EX
“THX Surround EX - Dolby Digital Surround EX” is a joint
development of Dolby Laboratories and the THX division of
THX Ltd.
2-7.12V Trigger Setup
Input:DVD
a.Trigger A
:On
In a movie theater, film soundtracks that have been encoded with
Dolby Digital Surround EX technology are able to reproduce an
extra channel which has been added during the mixing of the
program. This channel, called Surround Back, places sounds
behind the listener in addition to the currently available front
left, front center, front right, surround right, surround left, and
subwoofer channels.
b.Trigger B
:Off
Quit:|SETUP|
This additional channel provides the opportunity for more
detailed imaging behind the listener and brings more depth,
spacious ambience, and sound localization than ever before.
This sub-menu allows you to make the required settings to turn on
the output from the 12V TRIGGER terminal to control another
component or device with the DTR-8.3 for each input source.
When released to the home consumer market, movies that were
created using the Dolby Digital Surround EX technology, may
have a note to that effect on the packaging. A list of movies
created using this technology can be found on the Dolby web site
a. Trigger A
On: Select to activate the device connected to the 12V
TRIGGER A terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER
A terminal or you do not want the connected device to activate.
The DTR-7.3 can play the 5.1-channel sources in THX surround
EX mode, even if the source is not encoded in Dolby Digital
Surround EX format. In this case, the sound actually output from
the surround back channels depends on the source and may not
fit your tastes.
b. Trigger B
On: Select to activate the device connected to the 12V
TRIGGER B terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER B
terminal or you do not want the connected device to activate.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjust
3-1. Tone Control Sub-menu
3. Audio Adjust Setup Menu
Set the various parameters for the sound signals.
Separately adjust the bass and treble settings in 2 steps.
Advanced Menu
3.Audio Adjust
Advanced Menu
3.Audio Adjust
3-1.Tone Control
1.Tone Control
2.Surround Speakers
3.Sound Effect
4.Delay
a.Bass
:
:
0
0
b.Treble
5.LFE Level
6.Mono
7.Theater-Dimensional
8.Surround
Quit:|SETUP|
Setting
a. Bass
Values
–12 to +12
–12 to +12
Initial value
0
0
Advanced Menu
3.Audio Adjust
b. Treble
9.THX
10.Mono Movie
11.Enhanced 7
12.Orchestra
13.Unplugged
14.Studio-Mix
15.TV Logic
3-2. Surround Speakers Sub-menu
→default
This sub-menu allows you to decide which speakers to output to
when you are playing back a 5.1-channel source with surround back
speakers connected.
Setting
Values
Initial value
a. Surround Speakers Surround L/R, Surround Back, Surround L/R
Surr L/R + Back
Surround L/R: Select to output the sound to the surround left
and right speakers as normal and outputs nothing to the surround
back speaker.
Surround Back: Select to output the sound to the surround back
speakers and outputs nothing to the surround left and right
speakers.
Surr L/R+Back: Select to output the sound to both the surround
left and right speakers and the surround back speaker.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjust
3-3. Sound Effect Sub-menu
3-4. Delay Sub-menu
This sub-menu is used to turn on and off the various sound effects
available with the DTR-7.3.
This sub-menu gives you various ways to adjust the timing of the
audio output from the speakers to give certain soundfield effects or
to adjust for unwanted asynchronous video and audio tracks.
This sub-menu does not appear if “Direct” is selected as the listening
mode.
Setting
a. Re-EQ
Values
On, Off
On, Off
On, Off
Initial value
Off
Off
On
b. Upsampling
Setting
Values
Initial value
c. Subwoofer
a. A/V Sync
Relative Delay
b. Center
0.0 ms to 74.0 ms
0.0 ms
(Analog/PCM)
d. Late Night
Off, Low, High
Off
–4.0 ms to +6.0 ms
–4.0 ms to +6.0 ms
–4.0 ms to +6.0 ms
0.0 ms
0.0 ms
0.0 ms
c. Surr L/R
d. Surr Back
a. Re-EQ
Re-EQ (re-equalization) takes the edginess or “brightness” out of
your home cinema sound to compensate for the fact that sound
mixed for theaters may sound too bright when played back through
speakers in the home environment.
a. A/V Sync
If a digital signal processor is connected, there may be times when
the audio and video from a DVD or LD player is not output in perfect
sync. The result is where the sound and picture do not match and the
sound is heard too early. In such a case, use this setting to properly
synchronize the audio and video. This setting can be set between 0
and 74.0 ms in 0.5-ms increments. Under normal circumstances, this
can left at 0 ms. If set between 24.5 and 74.0 ms, upsampling is fixed
to 24.0 ms. Note that a change in the setting will not be displayed.
This setting will not appear if the selected input source is set for the
multichannel port.
This can be set to either “On” or “Off.”
You can use the Re-EQ button on the remote controller for setting
“On” or “Off.”
b. Upsampling
Upsampling processes the input digital signal, or the digital signal
converted from an analog input source, and converts its digital
sampling frequency to twice its current frequency for an even further
detailed sound reproduction. This can be set to either “On” or “Off.”
When “On” is selected, the Upsampling indicator lights.
c. Subwoofer
Relative Delay
b. Center, c. Surr L/R, d. Surr Back
When “Yes” is selected for the Subwoofer setting in the Speaker
Config Sub-menu, set this to “Off” if you do not want to have sound
output from the subwoofer when listening to Analog/PCM sources.
If “No” is selected for the Subwoofer setting in the Speaker Config
Sub-menu, this setting will not appear.
Besides level and delay adjustments, this setting provides the ability
to change or adjust the relative speaker position to fine tune the
soundfield for the listener. This is accomplished using Onkyo’s
unique Enhanced Spatial Positioning Algorithm. This adjustment
provides 10 milliseconds of delay for the speakers, which is
equivalent to moving the speaker 10 feet (3 meters) away. This
adjustment is set up to provide –4.0 or +6.0 milliseconds (–4 or +6
feet/–1.2 or +1.8 meters) of adjustment to the listener’s position.
Once the coarse adjustments (i.e., speaker level and distance
adjustments) are made, the system is set up to provide a typical or
broad surround environment. By adjusting the relative position of
the speakers, we are able to alter the soundfield to be more spread out
(deeper) or focused (shallower).
d. Late Night
The audio for movies made for the cinema have a large dynamic
range; thus, the difference between loud noises and soft noises is
great. To hear the quieter sounds such as background noises or
human conversations, the movie must be played back at larger
volumes. When this setting is set to “High” or “Low,” the dynamic
range of the sound is narrowed down to allow you to easily hear
minute sounds at low volumes. This function is especially useful if
you wish to play a movie at low volumes during the nighttime.
This can be set to either “Off” or “Low,” or “High.”
Note:
Notes:
Surr Back will not appear if the Surr Back/Zone 2 setting in the Surr
Back/Zone 2 Sub-menu of the Hardware Setup Menu is set to “Zone
2.”
• The Late Night function is effective only on Dolby Digital
encoded software.
• The depth of the Late Night effect is determined by Dolby
Digital software. With some sources, it may produce little or no
effect.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjust
3-5. LFE Level Sub-menu
3-7. Theater Dimensional Sub-menu
This sub-menu is for setting the LFE (Low Frequency Effect) levels
included in Dolby Digital and DTS software.
Select this to modify the Theater-Dimensional (T-D) listening
modes. The settings available are shown in the table below.
Setting
a. Dolby Digital
b. DTS
Values
–∞, –10 dB to 0 dB
–∞, –10 dB to 0 dB
Initial value
0 dB
Setting
a. Listening Angle
b. Center
Values
20˚, 40˚
Initial value
40˚
0 dB
On, Off
Off
Off
0 dB
Off
c. Front Expander
d. Virtual Surr Level
e. Dialog Enhance
On, Off
–3 dB to +3 dB
On, Off
a. Dolby Digital
The level can be adjusted to either –∞ or between –10 and 0 decibels
in 1-decibel increments. For Dolby Digital input source signals, the
LFE level set here is used. A setting of 0 decibels is recommended
for optimum performance; however, if the source is recorded with
the low frequency range too strong, lower this setting as necessary.
a. Listening angle
The listening angle is the angle subtended by the front left and right
speakers as seen from the listener. The processing for the virtual
surround will be based on this angle. The setting of 20 and 40
degrees are only for nominal purposes, so select the setting that is
closest to your actual listening angle.
b. DTS
The level can be adjusted to either –∞ or between –10 and 0 decibels
in 1-decibel increments. For DTS input source signals, the LFE level
set here is used. A setting of 0 decibels is recommended for optimum
performance; however, if the source is recorded with the low
frequency range too strong, lower this setting as necessary.
Front left speaker
Front right speaker
Listening angle
3-6. Mono Sub-menu
The settings of this sub-menu shown below are enabled when the
listening mode is set to “Mono.”
b. Center
Setting
a. Academy Filter
b. Input Channel
Values
On, Off
Initial value
Off
In the Theater-Dimensional mode, if the speaker system has a center
speaker, the center channel signal can be output from the center
speaker. For instance, in systems where the front left and right
speakers are small, use of the center speaker may provide a better
sound space and reduce the load on the front speaker. (For the proper
soundfield, it is important that the speaker levels and speaker distances
among the front right, front left, and center speakers are matched. In
order to ensure this, make sure that the settings in the Speaker Distance
Sub-menu and Level Calibration sub-menu are set correctly.)
Auto L+R, Left, Right
Auto L+R
a. Academy Filter
Older monaural film mixes relied on high-frequency rolloff in
presentation to sound properly balanced, so that excessive hiss from
the grain structure of the film would not be heard. The high-
frequency loss was typically due to a combination of optical slit loss,
electrical filters, loudspeaker response, and screen loss. Some films
have been transferred to video without such a high-frequency rolloff,
and thus sound overly bright and hissy.
The DTR-7.3 includes this “Academy filter,” which is based on
contemporary playback practices for such films over wide-range
systems.
On: Select to have the center channel signal output to the center
speaker.
Off: Select to have the center channel signal output to the front
left and right speakers (Phantom Center).
c. Front Expander
The front expander function spreads out the stereo image in front of
the listener. The created stereo image is as if the front speakers have
been farther apart for the feeling of a wide sound space. This is
especially useful for narrow listening angles of 20 degrees or less.
This can be set to either “On” or “Off.”
b. Input Channel
This allows you to set which input channel to use for monaural
sound.
On: Select to turn on the front expander function to simulate a
wider sound space.
Auto L+R: Select this under normal circumstances. When the
input source is center channel, this center channel is used as the
monaural sound input channel. Otherwise, the left and right
channels are mixed and the mixed signal is used as the monaural
sound input channel.
Off: Select to turn off the front expander function for a normal
sound space.
d. Virtual Surr Level
This setting adjusts the level of the virtual surround signal. This can be
set from –3 to +3 decibels. Lowering this setting can improve the
sound when the definition is unclear or when the sound feels
unnatural.
Left/Right: You will need to select either left or right when
playing a video source that contains bilingual data. In such a
case, the left and right channels will contain the audio for
different languages. Select the channel with the language you
desire.
e. Dialog Enhance
If the dialog from the center channel is difficult to hear in the
Theater-Dimensional mode, use this setting to improve the clarity.
On: Select to enhance the vocal ranges of the center channel
signal.
Off: Select to output the center channel signal at the regular level
and frequency characteristics.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjust
e. Pro Logic II Music Panorama
3-8. Surround Sub-menu
Use this setting to extend the front stereo image to include the
surround speakers for an exciting wraparound effect with side wall
imaging.
This sub-menu provides various settings for modifying the plain
Dolby Digital, DTS, and Pro Logic II Surround listening modes. The
settings that can be set are shown in the table below.
On: Select to turn on the PL II Music Panorama mode.
Off: Select to turn off the PL II Music Panorama mode.
Setting
Values
Initial value
a. Surr Mode
(Analog/PCM)
Pro Logic II Movie
Pro Logic II Music
DTS Neo:6 Cinema
DTS Neo:6 Music
Pro Logic II Movie
f. Pro Logic II Music Dimension
Use this setting to gradually adjust the soundfield forward or
backward.
The setting of “3” is the normal position. Change the setting to “2” or
lower to move the sound space forward and setting to “4” or higher
to move the sound space backward.
If the stereo recording has excessive broadness or too strong
surroundness, move the sound space forward to get the appropriate
sound balance. In contrast, if the stereo recording is somewhat felt
like monaural or has narrowness, move the sound space backward to
get more surroundness.
b. Surr Mode
(D.F.2ch)
Pro Logic II Movie
Pro Logic II Music
DTS Neo:6 Cinema
DTS Neo:6 Music
Pro Logic II Movie
c. Dolby D EX
(Dolby D)
Auto, On, off
On
d. DTS-ES
Auto, On, Off
Auto
<Pro Logic II Music>
e. Panorama
Off, On
Off
3
g. Pro Logic II Music Center Width
f. Dimension
0, 1, 2, 3, 4, 5, 6
0, 1, 2, 3, 4, 5, 6, 7
In Pro Logic II decoding, center signals are output from the center
speaker. When the center speaker is not used, the decoder will divide
the center signal equally to both the front left and right speakers to
create a “phantom” center sound image.
g. Center Width
3
<Neo: 6 Music>
h. Center Image
0, 1, 2, 3, 4, 5
3
The Pro Logic II Music Center Width mode allows you to adjust
from where the center sound image is heard. Using this, you can
have the soundfield be heard from the center speaker only, from the
front left and right speakers only (as a phantom center sound image),
or from all three speakers (center, front left and right) in various
level combinations. For home use, applying some width to the center
signal will improve the level balance for the center and main
speakers, and effect the width of the center sound image, or “weight”
of the sound. Many sound recordings processed for stereo playback
will be reproduced better by proper control of this setting. The
recommended setting for Pro Logic II Music mode is “3.” This
allows you to easily distinguish the Pro Logic II Music mode from
the Pro Logic II Movie mode whose setting is automatically set to
“0.”
a. Surr Mode (Digital)
Changes the surround mode for when 2-channel analog/PCM signals
are input.
b. Surr Mode (D.F.2ch)
Changes the surround mode for when 2-channel digital signals are
input.
c. Dolby Digital EX (Dolby D)
If you have surround back speakers connected, use this setting to
select whether or not you will use Dolby EX playback.
Auto: When the source has an EX flag (ID signal for Surround
EX), the playback is automatically changed to Dolby Digital EX.
If the source has no EX flag, the playback is changed to Dolby
Digital.
h. Neo:6 Music C Image
DTS Neo:6 derives a center channel from two-channel PCM and
On: The playback is set to Dolby Digital EX.
Off: The playback is set to normal Dolby Digital.
analog sources.
In cinema mode, for Lt/Rt film soundtracks, sounds steered to the
center are subtracted from the left and right channels.
In music mode, the intent in the front channels is less one of steering
and more one of stabilizing the front image by augmenting it with a
center channel, while preserving the original perspective of the
stereo mix. Therefore the derived center is never fully subtracted
from the left and right channels.
If your surround channel is monaural or you do not have a surround
channel, then the playback will be normal Dolby Digital regardless
of the above setting.
You can change the Dolby Digital EX mode settings easily using the
remote controller. While playing a Dolby Digital source, after
selecting Dolby D for listening mode, each press of the SURR button
on the remote controller cyclically changes the Dolby Digital EX
mode in the order of “Auto,” “On,” and “Off.”
Center Image is the factor controlling the amount of subtraction. It
varies between 0 and 5 in steps of 1 and the default value is 3.
When Center Image=5, the factor is zero and nothing is subtracted
from the left and right channels. When Center Image=0, the center
channel is subtracted from the left and right channels at half level
(–6 dB) for each channel. The signal level sent to the center channel
output is not affected by Center Image.
d. DTS-ES
This setting selects the DTS-ES mode.
Auto: Select to have the listening mode change automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1. If the DTS source
has no DTS-ES flag, the mode is changed to DTS 5.1 when the
DTS source has the DTS-ES flag (ID signal for DTS-ES).
This control should be set based on room layout and personal
preferences. A setting of 5 allows the left and right channels to pass
through unaltered from the stereo mix. A setting of 0 gives more
center channel dominance, which is particularly desirable if listeners
are located well off-center. At any setting, the center speaker anchors
the image.
On: Select to have the listening mode change automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1 when the DTS
source has the DTS-ES flag, and to DTS-ES Matrix 6.1 when the
DTS source has no DTS-ES flag.
Center Image is only enabled when the listening mode is DTS Neo:6
Music.
Off: Select to not use DTS-ES listening modes even when the
DTS source has the DTS-ES flag. With this setting, the DTS
sources are always played in DTS 5.1 mode.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjust
3-9. THX Sub-menu
3-10. 3-11. 3-12. 3-13. 3-14. 3-15.
Mono Movie/Enhanced 7/Orchestra/Unplugged/
Studio Mix /TV Logic Sub-menu
This sub-menu allows you to set the settings that will be enabled
when the THX listening mode is selected. The settings available are
shown in the table below.
The settings of these sub-menus become effective when any of the
Mono Movie, Enhanced 7, Orchestra, Unplugged, Studio-Mix, or
TV Logic listening modes are selected. When one of the listening
modes is selected, the settings in the sub-menu of that listening mode
become enabled.
Setting
a. Re-EQ (THX)
b. Decoder (2ch)
Values
Off, On
Initial value
On
PL II Movie
PL II Movie
Neo:6 Cinema
c. THX Surr EX
(Dolby D)
Auto, Off, On
Auto, Off, On
On
Setting
Values
Off, On
Initial value
On
a. Front Effect
b. Reverb Level
c. Reverb Time
d. DTS-ES
Auto
Low, Mid, High
Short, Mid, Long
Mid
Mid
a. Re-EQ (THX)
Re-EQ (re-equalization) takes the edginess or “brightness” out of
your home cinema sound to compensate for the fact that sound
mixed for theaters may sound too bright when played back through
speakers in the home environment.
a. Front Effect
Some live recordings contain acoustic reverberation. When you play
these sources, more reverberation will be applied by the DSP,
creating too much reverb effects and the sound loses frame or
presence. In this case, set this setting to “Off” so that no
reverberation from the DSP will be applied to the sound output from
the three front channels. With this setting, the sound source is played
as it is without any further reverberation.
This can be set to either “On” or “Off”.
b. Decoder (Analog/PCM)
This setting allows you to select the decoding mode for THX
processing.
PL II Movie: Select for Dolby Pro Logic II Movie.
Neo:6 Cinema: Select for DTS Neo:6 Cinema.
b. Reverb Level
This setting allows you to adjust the depth of acoustic reverberation
to match the playback source material, the acoustics of your room,
and such other factors.
c. THX Surr EX (Dolby D)
This setting allows you to set whether or not Dolby Digital sources
will be played back using THX Surround EX when a surround back
speaker is connected.
Select from the three settings “Low,” “Mid,” and “High.”
c. Reverb Time
Auto: Select to automatically output sources with EX-
identifying signals using THX Surround EX.
Adjust the reverb time to match the source being played back and the
acoustics of the room. Select from the three settings “Short,” “Mid,”
and “Long.”
On: Select to output using THX Surround EX regardless of
whether or not the source contains EX identifiers.
Off: Select not to output using THX Surround EX regardless of
whether or not the source contains EX identifiers (Dolby D is
used).
Note:
THX Surround EX (Dolby D) will not appear if the Surr Back/Zone
2 setting in the Surr Back/Zone 2 Sub-menu of the Hardware Setup
Menu is set to “Zone 2.”
d. DTS-ES
This setting allows you to select the DTS-ES mode for THX
processing.
Auto: Select to have the listening mode change automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1. If the DTS source
has no DTS-ES flag, the mode is changed to DTS 5.1 when the
DTS source has the DTS-ES flag (ID signal for DTS-ES).
On: Select to have the listening mode change automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1 when the DTS
source has the DTS-ES flag, and to DTS-ES Matrix 6.1 when the
DTS source has no DTS-ES flag.
Off: Select to not use DTS-ES listening modes even when the
DTS source has the DTS-ES flag. With this setting, the DTS
sources are always played in DTS 5.1 mode.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjust
Settings possible for each listening mode (3-1. 3-2. 3-3. Sub-menu)
Setting
3-1. Tone Control
3-2. Surround Speakers
a. Surround Speakers
3-3. Sound Effect
b. Upsampling*2
a. Bass
a. Re-EQ
c. Subwoofer*2
b. Treble
Listening mode
Mono
Direct/Pure Audio
Stereo
Theater-Dimensional
Dolby EX
DTS
DTS-ES Matrix 6.1
DTS-ES Discrete 6.1
DTS 96/24
Dolby Digital
Dolby Pro Logic II
DTS-ES Neo:6
THX Cinema (PLII)
THX Cinema (Neo:6)
THX Surround EX
DTS-ES THX Cinema
Mono Movie
Enhanced 7
Orchestra
Unplugged
Studio-Mix
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G *1
G *1
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
TV Logic
All CH Stereo
G
*1 Enabled for Dolby Pro Logic II Movie and DTS Neo:6 Cinema input sources.
*2 Takes effect when playing an analog/PCM source in any of the listening modes marked with “G.”
*3 Takes effect when playing a Dolby Digital source in any of the listening modes marked with “G.”
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Preference
4-1. Volume Setup Sub-menu
4. Preference Menu
This sub-menu allows you to make various settings concerning the
volume control of the DTR-7.3.
Advanced Menu
4.Preference
Advanced Menu
4.Preference
1.Volume Setup
2.Headphones Level Setup
3.OSD Setup
4-1.Volume Setup
4.OSD Position
a.Volume Display
:Absolute
|ENTER|Quit:|SETUP|
b.Muting Level
:-oodB
c.Maximum Volume
:Off
d.Power On Volume
:Last
Quit:|SETUP|
a. Volume Display
You can choose from two ways of displaying the volume setting on
screen.
Absolute: This displays the volume with a minimum of 0 for no
sound and a maximum of 100. As a reference, the volume setting
of Ref (82) is equivalent to 0 decibels for the relative display
method.
Relative: This displays the volume as a decibel value on a scale
with a designated reference point that is displayed as 0, which
equals the volume setting of 82 of the absolute display method.
With this display method, the minimum value is –∞, the next
highest is –81, and the maximum value is +18.
b. Muting Level
This sets the attenuation level during playback when the Muting
button is pressed on the remote controller. This can be set to
–∞, or between –50 and –10 decibels in 10-decibel increments.
c. Maximum Volume
This setting allows you to set the maximum volume that can be
output with the Master Volume dial. Setting a maximum volume
allows you to prevent components from being damaged by
excessively loud volumes. For the absolute volume display method,
this can be set between 50 and 99. For the relative volume display
method, this can be set between –32 and +17 decibels. To not set a
maximum volume, select “Off.”
d. Power On Volume
This sets a designated volume for which the DTR-7.3 will be set to
every time that the power is turned on. This prevents the DTR-7.3
from suddenly outputting very loud sounds if it is turned on while it
is set to an extremely high volume. For the absolute volume display
method, this can be set between 0 and 100. For the relative volume
display method, this can be set between –∞, –81 and +18 decibels.
To have the DTR-7.3 turned on with its current volume setting, set
this to “Last.”
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Preference
c. Immediate Display
4-2. Headphones Level Setup Sub-menu
On: Select to have the screen immediately display certain
operations as you perform them (e.g., having the input source
displayed whenever an input source selector button is pressed).
The display will remain for five seconds after the operation is
completed.
If you notice a large difference in the volume when listening to the
headphones from when listening to the speakers, you can change the
headphone volume level so that you do not have to make
adjustments with the main volume dial each time you put on the
headphones. The headphone volume can be adjusted between –12
and +12 decibels.
Off: Select to turn off the immediate display of operations.
Advanced Menu
4.Preference
VIDEO 1
d. Display Position
4-2.HeadphoneLevel Setup
Use this setting to select the position of the immediate display that
appears when certain operations are performed. You can position the
immediate display at any of ten different levels ranging from the top
all the way to the bottom.
a.Headphones Level
: 0dB
e. TV Format
(Australian models only)
Quit:|SETUP|
The default setting is “Auto,” which means that the television format
is detected and automatically set by the DTR-7.3. However, if you
know the correct format, you can use this setting to choose either
PAL or NTSC so that no time is wasted on detection.
4-3. OSD Setup Sub-menu
4-4. OSD Position Sub-menu
This sub-menu allows you to customize the OSD Setup Menu to
display in the manner you desire.
This sub-menu allows you to adjust the position of the OSD Setup
Menu as it is displayed on your screen. Depending on the monitor
used, there may be cases where the OSD Setup Menu is not
displayed in the center and parts of the menus are cut off. To adjust
the position of the OSD Setup Menu, simply press the cursor buttons
to inch the menu to position you desire.
Advanced Menu
4.Preference
4-3.OSD Setup
a.Background Color
:Blue1
Advanced Menu
4.Preference
b.Superimpose Mode
:Normal
c.Immediate Display
:On
d.Display Position
:Bottom
4-4.OSD Position
e.TV Format :Auto
Quit:|SETUP|
a. Background Color
Exit:|RETURN|
Select either Blue1, Blue2, Green1, Green2, Magenta, Red1, or
Red2 as the background color when the OSD Setup Menu is
displayed.
b. Superimpose Mode
Off: Select to have the OSD Setup Menu displayed on the
selected background color.
Hint:
If this is set to “Off,” the background color will not be displayed
even when there is no video signal input.
Normal: Select to have the OSD Setup Menu superimposed
over the current video if one is displayed or on the selected
background color if there is no video signal.
Black: Select to have the OSD Setup Menu displayed on a black
background at all times.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using remote controller
Overview
The RC-514M remote controller is a useful tool that can not only
operate the DTR-7.3, but also all the other components of your home
theater as well. To operate any component, first press the Mode
button on the remote controller that corresponds to the component
that you wish to control. Then simply press the desired operation
button and the component will operate accordingly.
To operate a satellite, tuner, cable, VCR, or television with the
remote controller, first program the signal to the button.
There are two methods. One method is selecting the name of a
different brand from the table, entering the setting number listed, and
calling up the pre-programming code (see page 65). The other
method is sending the commands from the other brand’s remote
control directly into this remote controller (see page 69).
Controlling an Integra/Onkyo cassette tape deck
The
connector of the Integra/Onkyo cassette tape deck must be
connected to the DTR-7.3 (see page 26).
1. Press the RCVR Mode button.
The RCVR Mode button lights.
2. Press the desired operation button.
RCVR Mode
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo cassette
tape deck.
VOL
Operation buttons:
: Play
Muting
: Stop
: Rewind
TAPE
operation
buttons
: Fast forward
: Skips to beginning of next track during playback
: Skips to beginning of current track during playback
Rec G: Record/Pause
: Reverse playback
You may also use the following buttons:
VOL : Adjusts volume at DTR-7.3
Muting: Activates muting function at DTR-7.3
Note:
Even for devices with the
and
buttons, signal discrepancies
may cause them not to work properly.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using remote controller
Controlling an Integra/Onkyo DVD player
The
connector of the Integra/Onkyo DVD player must be
connected to the DTR-7.3 (see page 26).
1. Press the DVD Mode button.
The DVD Mode button lights.
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo DVD
player.
Operation buttons:
On: Turns DVD player on and off
Standby: Turns DVD player off (Some sets may not respond to this
button. In this case, use the ON button to put the DVD player in the
standby state.)
Setup: Displays the OSD of the DVD player
Standby
On
: Moves cursor in the OSD Menu of the DVD player
ENTER: Enter button for the OSD Menu of the DVD player
Return: Return button for the OSD Menu of the DVD player
DVD Mode
Return
ENTER,
Top Menu or Menu: Displays menu screens recorded on DVD
media
Setup
VOL
Disc
Disc
: Selects disc in DVD changer
Audio Sel: Selects audio or language track (if recorded on the DVD)
Menu
Muting
Top Menu
Audio Sel
Angle: Selects a camera angle (if recorded on the DVD)
Subtitle: Selects subtitle language (if recorded on the DVD)
Subtitle
Angle
Search: Searches for location on disc to start playback
DVD
Random: Random playback
: Chapter/Track down
: Chapter/Track up
: Play
operation
buttons
: Stop
Numeric keys
Search
: Fast reverse
: Fast forward
: Pause
: Opens/closes the disc tray
0, 1 to 9, +10: Numeric keys
You may also use the following buttons:
VOL : Adjusts volume at DTR-7.3
Muting: Activates muting function at DTR-7.3
Note:
When operating an Integra/Onkyo DVD player directly with the
remote controller without connecting the
programming is necessary (see page 65).
terminals, pre-
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Using remote controller
Controlling an Integra/Onkyo CD player
The
connector of the Integra/Onkyo compact disc player must be
connected to the DTR-7.3 (see page 26).
1. Press the CD Mode button.
The CD Mode button lights.
Standby
CD Mode
On
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo compact
disc player.
Disc
Operation buttons:
VOL
On: Turns on and off the compact disc player (same as Standby
button on the remote controller)
Disc : Selects a disc in the CD changer
: Track down
Muting
: Track up
CD
: Play
operation
buttons
: Stop
: Skip backward
: Skip forward
: Pause
Numeric keys
: Opens/closes disc tray
0, 1 to 9, +10: Numeric keys
Random: Random playback
You may also use the following buttons:
VOL : Adjusts volume at DTR-7.3
Muting: Activates muting function at DTR-7.3
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using remote controller
Controlling an Integra/Onkyo MD recorder
The
connector of the Integra/Onkyo MD recorder must be
connected to the DTR-7.3 (see page 26).
1. Press the SAT/MD Mode button.
Standby
On
The SAT/MD Mode button lights.
2. Press the desired operation button.
SAT/MD Mode
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Integra/Onkyo MD
recorder.
Operation buttons:
VOL
On: Turns on and off MD player (same as Standby button on the
remote controller)
Muting
: Track down
: Track up
MD
operation
buttons
: Play
: Stop
: Skip backward
: Skipt forward
Rec G: Record
: Pause
Numeric keys
Enter
: Eject
1 to 9, 0, --/---: Numeric keys
ENTER: Enters the settings
You may also use the following buttons:
VOL : Adjusts volume at DTR-7.3
Muting: Activates muting function at DTR-7.3
Note:
The SAT/MD button is used for operating satellite tuners and
Integra/Onkyo MD recorders. Be aware that if you enter the preset
code for a satellite tuner as shown on page 65, then this button cannot
be used to operate Integra/Onkyo MD recorders.
If this is the case, to operate an Integra/Onkyo MD recorder, you
must first erase the satellite tuner code by following the directions
given in “Erasing all the commands programmed under a MODE
button” on page 70.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering a pre-programming code
The remote controller has three learning functions. One is entering
Learning a pre-programming code
the pre-programmed code for a remote controller of another
manufacturer. Another is the normal learning function that enables
the remote controller to learn the codes directly from other remote
controllers (see page 69). And the last is a macro learning function
that enables you to program a series of operations into the remote
controller so that the operations can all be performed at once by
pressing one button.
By entering a pre-programming code, you can have the RC-514M
remote controller operate a component made by another
manufacturer. The buttons that are used for operation are given on
the next page.
1. Find the 3-digit number listed for the manufacturer
name of the component that you want to operate in
the table on the next page.
2. Turn on the component that you want to operate (i.e.
DVD, satellite tuner, or television).
Send/Learn
indicator
3. While holding down the Mode button on the RC-514M
that you want to program, press the Display button,
and then release both buttons.
The Send/Learn indicator lights when the Mode button is
pressed and turns off when the Display button is pressed. When
the indicator turns off, release both buttons. The Send/Learn
indicator lights again.
Buttons that can
be preprogrammed
VOL
4. Within 30 seconds, enter the 3-digit code number.
The Send/Learn indicator slowly flashes twice. If the Send/
Learn indicator quickly flashes three times, then either a
mistaken 3-digit code was entered or an incorrect operation was
performed. If this occurs, return to step 3.
5. Press the button that you programmed and check if
the system operates correctly.
• If the component does not operate properly, return to step 3
and repeat the steps above.
• If it still does not operate properly, program the command
directly from the other remote controller normally (see page
69).
Numeric keys
Display
When entering the code of Integra/Onkyo DVD players:
There are three SETTING numbers. Choose the SETTING number
according to how you will be using the DVD player.
No. 601/613: These codes are for operating the Integra/Onkyo DVD
player by pointing the remote controller directly at it, either because
Caution
With some brand’s components, some buttons may not work
correctly. In this case, program the command directly from the other
remote controller normally (see page 69).
it does not have an
terminal, or it does but you are not connecting
it with an cable. First enter 601 and if it does not operate
properly, enter 613.
No. 600: This code is for Integra/Onkyo DVD players that have an
terminal that you are connecting to the DTR-7.3 with an
cable. You will then operate the DVD player by pointing the remote
controller at the remote control sensor on the DTR-7.3. You do not
need to enter this code because it is factory preset. However, if the
code has been changed to 601 or 613, then you will need to change it
back to 600.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering a pre-programming code
Pre-programming codes
VCR
TV
BRAND
SETTING No.
300, 301, 302
303, 304, 305, 306,
307
308
309
310
311, 312, 313
314
315, 316
317
318, 319, 320, 321,
322
323
BRAND
SETTING No.
100, 101
102, 103, 104
105
106
107
108, 109
110
111, 112, 113
114
115, 116
117, 118, 119, 120,
121
AIWA
AKAI
AIWA
AKAI
Note:
If more than one code is given in the table,
try each code one by one until you reach the
code that works (i.e. if the first code does
not work, then try the next).
AUDIOSONIC
BELL & HOWELL
BLAUPUNKT
BRIONVEGA
CENTURION
COLTINA
CORONAD
CROWN
DAEWOO
BAIRD
BELL & HOWELL
BLAUPUNKT
CGM
COLTINA
DAEWOO
DIGITAL
DVD
BRAND
SETTING No.
602, 609
603
DENON
HITACHI
JVC
EMERSON
604
KENWOOD
MAGNAVOX
MARANTZ
MITSUBISHI
INTEGRA/ONKYO
PANASONIC
PIONEER
PROSCAN
RCA
605
606, 613
607
608, 613
600, 601, 613
609
610
611
611
FENNER
FISHER
DUAL
EMERSON
122
324, 325, 326, 327
123, 124, 125, 126,
127
128, 129
130, 131
132
FUJITSU GENERAL 328
FUNAI
GE
GO VIDEO
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
JVC
FENNER
FERGUSON
FISHER
329
330, 331
332, 336, 337
333, 334
335
FUNAI
133, 134, 135
FUJITSU GENERAL 136, 137, 138
GE
139, 140, 141
142, 143
144
145, 146
147, 148, 149, 150
151
SONY
612
338
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
HYPER
TOSHIBA
YAMAHA
ZENITH
613
609, 614
613, 615
339, 340, 341
342, 343, 344, 345,
346, 347, 348, 349,
350
SAT
LOEWE
MAGNAVOX
MITSUBISHI
351, 352
INNO HIT
IRRADIO
JVC
152
103
BRAND
SETTING No.
700
353, 354, 355
356, 357, 358, 359,
360, 361, 362, 363,
364
365, 366, 367
313
ECHOSTAR
GENERAL
INSTRUMENTS
HITACHI
HUGHES
153, 154, 155, 156,
157
158
159, 160
161
701
702
KENDO
KTV
LUXOR
NEC
NOKIA
NETWORK
SYSTEMS
PANASONIC
PRIMESTAR
PROSCAN
RCA
NORDMENDE
OKANO
ORION
368, 369, 370
371, 372
319, 373
374, 375, 376, 377,
378
353, 379, 380
311
381
382
383
MAGNAVOX
MARANTZ
MARK
MATSUI
MITSUBISHI
MIVAR
NEC
NOKIA
OCEANIC
NORDMENDE
OKANO
ORION
PANASONIC
PHILIPS
PIONEER
PROSCAN
QUASAR
RADIO SHACK
RCA
162, 163
164
165
166, 167, 168, 169
170, 171, 172, 173
174, 175
176, 177
178, 179, 180, 181
181
703
704
705
706, 707
706, 707
708
PANASONIC
PHILIPS
PHONOLA
PIONEER
RCA
SABA
SAMSUNG
SONY
TOSHIBA
709
182, 183
152
CABLE
BRAND
GENERAL
INSTRUMENTS
GEMINI
384, 385, 386, 387,
388, 389, 390
391, 392, 393
394
SETTING No.
184, 185, 186
187, 188, 189, 190
152, 162, 191
192, 193
194
SANYO
SCOTT
SELECO
SHARP
SHINTOM
SIEMENS
SONY
500
501
395
HAMLIN
JERROLD
502, 503, 504, 505
500, 506, 507, 508,
509, 510, 511, 512,
513, 514
515, 516, 517
518
519, 520, 521
522, 523
524, 525, 526, 527,
528, 529
396, 397, 398, 399
400
401
402, 403, 404, 405,
406, 407, 408, 409,
410, 411, 412, 413
414
414, 415
416, 417
418, 419, 420
195
196
110, 141, 197, 198,
199, 200
182, 183, 201
202, 203, 204, 205,
206, 207, 208
209, 210, 211, 212
103
MACOM
MAGNAVOX
OAK
PANASONIC
PHILIPS
SABA
SAMSUNG
SYMPHONIC
TEKNIKA
TELEFUNKEN
TOSHIBA
WHITE
WESTINGHOUSE
WATSON
SANYO
SCHNEIDER
SEARS
SELECO
SHARP
PIONEER
SCIENTIFIC
ATLANTA
SAMSUNG
TOCOM
530, 531
213
333
421
422
214, 215
216, 217
218, 219, 220, 221,
222, 223
224, 225
201, 226, 227
228
213, 229
230
231, 232
532, 533, 534
535
536
ZENITH
SONY
ZENITH
537, 538
SYMPHONIC
TELEFUNKEN
THOMSON
TOSHIBA
UNIVERSUM
ZENITH
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your programmed remote controller
After entering a pre-programming by following the procedure
given above, the following modes become enabled for use.
DVD Mode (DVD Player Mode)
Operations are the same as explained on page 62.
SAT Mode (Satellite Tuner Mode)
1. Press the SAT/MD Mode button.
The SAT/MD Mode button lights.
Standby
On
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your satellite tuner unit.
SAT/MD Mode
The buttons given below have operations programmed
into them.
On: Turns on and off satellite tuner unit (same as Standby button on
the remote controller)
ENTER,
CH
VOL
CH
: Changes selected preset channel
: Moves cursor
Menu
Muting
ENTER: Confirms selection
Menu: Displays menu
0,1 to 9: Numeric keys
ENTER: Confirm
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-7.3
Muting: Activates the muting function at the DTR-7.3
Numeric keys
Enter
Cable Mode (Cable Mode)
1. Press the Cable Mode button.
The CABLE button lights.
Standby
On
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your cable TV unit.
Cable Mode
The buttons given below have operations programmed
into them.
On: Turns on and off cable TV unit (same as Standby button on the
remote controller)
VOL
CH
CH
: Changes selected preset channel
Muting
0,1 to 9: Numeric keys
ENTER: Confirm
You may also use the following buttons:
VOL : Adjusts the volume at the DTR-7.3
Muting: Activates the muting function at the DTR-7.3
Numeric keys
Enter
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating your programmed remote controller
VCR Mode (VCR Mode)
1. Press the VCR Mode button.
The VCR button lights.
Standby
On
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your VCR.
VCR Mode
The buttons given below have operations programmed
into them.
On: Turns on and off the VCR (same as Standby button on the
remote controller)
VOL
CH
TV/VCR
CH
: Changes selected preset channel
TV/VCR: Switches VCR input setting
Muting
: Play
Video cassette
recorder
operation
buttons
: Stop
: Rewind
: Fast Forward
: Pause
0,1 to 9, +10: Numeric keys
You may also use the following buttons:
Numeric keys
VOL : Adjusts the volume at the DTR-7.3
Muting: Activates the muting function at the DTR-7.3
TV Mode (TV Mode)
1. Press the TV Mode button.
The TV button lights.
Standby
On
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your television.
TV Mode
TV
The buttons given below have operations programmed
into them.
On: Turns on and off the television (same as Standby button on the
remote controller)
VOL
CH
TV : Turns on and off the television (and switches to the TV mode)
CH
: Changes television channel
TV/VCR
Muting
TV/VCR: Switches television input setting
0,1 to 9, +10: Numeric keys
ENTER: Confirm
VOL : Adjusts volume at television
Muting: Activates muting function at television
Numeric keys
Enter
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the commands of remote controllers
for other devices into the remote controller
Programming procedure
S
E
M
L U
When programming the commands of another remote controller to
O
V
T I N G
U
the RC-514M remote controller, you must first decide under which
E
T
N
O
T
S
E
T
L
E
S
Mode button you want the commands to be linked. In general, you
will select the Mode button that corresponds to the component you
are programming. For example, if you are programming the
functions from a remote controller for a compact disc player, you
would choose the CD Mode button. Then, by pressing the CD Mode
button, the buttons on the RC-514M remote controller will change to
the commands you program here to operate the compact disc player.
After programming which Mode button to use, you will then transfer
the separate commands from the other remote controller over to the
RC-514M remote controller one at a time. Each command is then
programmed to a different button on the RC-514M remote
controller. Any button is programmable for this step except for the
eight Mode buttons (RCVR, CD, DVD, SAT/MD, NET A, TV,
VCR, and CABLE), the two Macro buttons (1 and 2), and the Light
button.
H
C
T
S E
E
R
E
C
D
V
P
R
E
N
U
D
H
T
U
O
P
T
N
L T I - I C
N
P
U
H O
P
O
U
O
M
R
R
G
E
T
D
R
R
O
E
U
E C
C
I S
M
N
S
- 2
E L
O
D
D
T U
S
E
C
R
T
E
I D
U
P
M
V
I N P E
D I M
A
- 1
T
O
E
P
I D
E
V
L E
S
V D
D
R
E
W
O
P
2 to 6 inches
(5 to 15 cm)
Even after the commands have been memorized, keep your old
remote controller in a safe place. If for some reason the commands
are lost (e.g., when the batteries run down), it will be necessary to
memorize them once again.
1. Place the remote controller and the remote controller
for the other device facing each other at a distance of
2 to 6 inches (5 to 15 cm) apart.
2. While pressing and holding down the desired Mode
button on the remote controller, press the Enter
button and then release both buttons.
The Send/Learn indicator lights when the Mode button is
pressed and turns off when the Enter button is pressed. When the
indicator turns off, release both buttons. The Send/Learn
indicator lights again.
Send/Learn
indicator
3. Press and release the button on the remote controller
to which you want to transfer the next command.
You may select any button excluding the eleven ones indicated
in the figure below. When you press the button, the Send/Learn
indicator turns off. When you release the button, the indicator
lights again.
Mode
buttons
If you press the wrong button by mistake, press that same button
again. The Send/Learn indicator flashes twice, and the remote
controller exits the programming mode.
Light
Macro 1
Macro 2
Mode buttons
Enter
:
Buttons that cannot be programmed.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the commands of remote controllers for other devices into the
remote controller
4. Press and hold down the button (that corresponds to
the command you are programming) on the remote
controller of the other device until the Send/Learn
lamp on the remote controller flashes twice.
Erasing the programmed command from one
button
You can only erase memorized commands and not preset ones.
After flashing twice, the Send/Learn indicator will light again.
1. Press and hold down the Mode button for the
command, press the Enter button, and then release
both buttons.
5. Repeat Steps 3 and 4 to transfer all the commands
you desire from the other remote controller and
program them to buttons on the remote controller
under the same Mode.
When you press the Mode button, the Send/Learn indicator
lights. When you press the Enter button, the lamp turns off.
When you release the buttons, the lamp lights again.
Repeat Steps 2 through 4 to program commands to a different
Mode (e.g., when programming from a different remote
controller).
2. Press and release the button for the command you
wish to erase.
When you press the button, the Send/Learn indicator turns off.
When you release the button, the lamp lights again.
6. Press the Mode button that you pressed in step 2 to
complete the programming.
3. Press and release the same button again.
7. Operate the newly programmed buttons to make sure
the learning function was performed properly.
The Send/Learn lamp slowly flashes twice. The memorized
command is erased.
Notes:
Note:
• The remote controller codes for Integra/Onkyo compact disc
players, cassette tape decks, DVD players, and mini disc
recorder have already been programmed into buttons on the
remote controller. You may, however, use these buttons to
program the codes for other remote controllers. If you wish to
restore the Integra/Onkyo preset codes after you program new
codes, you must first erase the new codes.
If no button is pressed for more than 30 seconds during the erasing
procedure, the Send/Learn indicator flashes three times quickly, and
the remote controller exits the erasing mode. Resume from Step 1.
Erasing all the commands programmed under a
Mode button
• The remote controller has 408 memory slots (8 modes × 51
buttons). Some remote controllers may have more commands
that can be remembered by the remote controller. In such cases,
it will be necessary for you to determine which commands are
more important than others.
1. Press and hold down the desired Mode button, press
the Enter button twice, and then release both
buttons.
• If the Send/Learn indicator quickly flashes three times and turns
off, then the remote controller has exited the programming mode
because either you have made a mistake during programming or
a time-out has occurred because no button has been pressed.
Resume from Step 2.
When you press the Mode button, the Send/Learn indicator
lights. When you press the Enter button, the lamp turns off.
When you release the buttons, the lamp slowly flashes twice and
then lights again.
• If you try to program beyond the learning capacity of the remote
controller, the Send/Learn indicator flashes six times quickly,
and the remote controller exits the programming mode. Try
programming under a different Mode button.
2. Press and release the same Mode button again.
When you release the button, the Send/Learn indicator slowly
flashes twice. This erases all the commands memorized to the
Mode button.
• When you want to program a command to a button to which you
have already programmed a command, simply follow the same
procedure given and the previous programming for that button
will be overwritten.
Notes:
• If no button is pressed for more than 30 seconds during the
erasing procedure, the Send/Learn indicator flashes three times
quickly and the remote controller exits the erasing mode.
Resume from Step 1.
• The remote controller uses infrared rays to send its commands,
as do most other remote controllers. Though most remote
controller codes can be memorized by the remote controller, be
aware that some remote controllers use systems that are quite
different from the remote controller and therefore may not be
able to be programmed.
• If you perform an invalid operation during erasing, the Send/
Learn indicator flashes three times quickly, and the remote
controller exits the erasing mode. Resume from Step 1.
• If many commands have been programmed to the Mode button,
then the Send/Learn indicator may remain lit for up to 20
seconds during Step 2. This is not a malfunction.
• Some remote controllers have a single button that performs
multiple functions (for example, the function may change each
time the button is pressed). If this is the case, each function must
be programmed to a separate button on the remote controller.
• Once you have transferred the commands from the other remote
controller, refer to the instruction manual that came with that
product for instructions on how to operate that product.
• Make sure both the remote controller and the other remote
controller have new batteries. If either of them has batteries that
are low, you may not be able to program the commands of the
other remote controller properly into the remote controller.
See page 72 for how to erase the memorized commands from all
buttons.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the macro function
Programming the macro
What is the macro function?
A macro function enables you to program a series of button
operations (up to 16) on the remote controller into a single button.
The series of operations are then called a macro. For example, to
play a compact disc player connected to the DTR-7.3 normally, you
must perform the following steps:
With the macro function, you can program a series of button
operations as a macro into the Macro button so the macro can be
executed with just one touch. Note that for the macro function, only
one macro can be programmed. For example, to program the macro
described above on this page for the Macro button, perform the steps
given below.
1. Press the RCVR Mode button.
2. Press the On button.
1. Press and hold down any one of the 8 Mode buttons,
press the Macro 1 (or 2) button, and then release
both buttons.
3. Press the CD (Input Selector) button.
4. Press the CD Mode button.
5. Press the playback ( ) button.
When you press the Mode button, it lights and the Send/Learn
indicator lights. When you press the Macro 1 (or 2) button, the
indicator turns off. When you release the buttons, the indicator
flashes briefly and then lights again.
2. Press the operation buttons you wish to program in
order (in this case, press RCVR Mode → On → CD
(Input Selector) → CD Mode → playback ( ) button).
By using the macro function, you can perform the above five
operations by only pressing one button.
When you press each button, the Send/Learn indicator turns off.
When you release the button, the indicator lights.
Send/Learn
indicator
3. Press the Macro 1 (or 2) button to complete the
procedure.
The Send/Learn indicator slowly flashes twice.
On
4. Check to see if the macro has been properly
programmed.
Macro 1
Macro 2
RCVR Mode
Mode buttons
Notes:
CD Mode
• You may program up to 16 button operations into the macro
function. If you try to program a 17th operation, it will be
ignored, and programming is stopped.
• If the Send/Learn indicator quickly flashes three times and turns
off, then the remote controller has exited the programming mode
because either you have made a mistake during programming or
a time-out has occurred because no button has been pressed.
Resume from Step 1.
(CD playback)
CD
(Input
Selector)
Executing the macro
Perform the procedure below to execute the macro that you have
programmed into the remote controller. After programming the
macro, you should always run it at least once to make sure that it has
been programmed properly.
Point the remote controller at the DTR-7.3 and press the
Macro 1 (or 2) button.
It may take a while for the macro to finish transmitting, so be sure to
continue pointing the remote controller at the device until the Send/
Learn indicator turns off.
Tips:
• If you erase or change the command of a button programmed in
the macro, that operation of that button will no longer work in
the macro. In this case, it will be necessary for you to reprogram
the macro in order to avoid incorrect operation.
• The codes programmed into the macro will be transmitted at an
interval of 0.5 seconds. However, some devices may not be able
to complete one operation in 0.5 seconds and may miss the next
code. In this case, after pressing one operation button, you can
press the same Mode button again before pressing the next
operation button to add another 0.5 seconds between the two
operations.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the macro function
Erasing a macro from the Macro 1 (or 2) button
Send/Learn
indicator
1. Press and hold down any one of the 8 Mode buttons,
press the Macro 1 (or 2) button, and then release
both buttons.
When you press the Mode button, it lights and the Send/Learn
indicator lights. When you press the Macro 1 (or 2) button, the
indicator turns off. When you release the buttons, the indicator
flashes once.
Macro 1
Macro 2
Mode buttons
2. Press the Macro 1 (or 2) button again.
The Send/Learn indicator slowly flashes twice. The macro
programmed to the Macro button is erased.
Notes:
• If the Send/Learn indicator quickly flashes three times and turns
off, then the remote controller has exited the erasing mode
because either you have made a mistake during erasing or a time-
out has occurred because no button has been pressed. Resume
from Step 1.
• If you press a button other than Macro 1 (or 2) button in Step 2,
then you will in effect be overwriting the previous macro with a
new macro.
Enter
Erasing all commands and macros that have
been programmed
Send/Learn
indicator
This procedure will erase all the commands and macros that you
have programmed into the remote controller and return it to its
default settings. This operation will not affect the preset settings of
the remote controller.
On
Standby
1. Open the battery cover and remove the batteries from
the remote controller.
2. While pressing and holding down the On and
Standby buttons, re-insert the batteries in their
correct orientation, and then release both buttons.
The Send/Learn indicator flashes slowly.
3. Press the Enter button.
The Send/Learn indicator lights up for about ten seconds and
then turns off.
All programmed commands and macros are erased and the remote
controller returns to its factory presets.
Notes:
• Proceed to Step 3 immediately after Step 2; otherwise, the
batteries will be consumed quickly.
• If you press any button other than the Enter button in Step 3,
nothing will be erased. In this case, resume from Step 1.
Enter
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
If a problem occurs while you are using the remote controller, first
try to operate the controls on the front panel of the DTR-7.3 to make
sure that it is not due to a malfunction (or worn out batteries) in the
remote controller.
Low frequency humming is heard.
• Not properly grounded.
©Check outer conductor of input plugs.
• Turntable motor is not properly grounded.
©Check for proper ground connection.
• Audio connection cables on the rear panel are connected incorrectly.
©Adjust the placement of the cable to reduce hum.
POWER
Howling is heard when the volume is turned up.
No power.
• Turntable and speakers are located too close together.
©Move them farther apart.
• Power cord is disconnected.
©Connect power cord (see page 28).
• External noise is affecting the internal microcomputer.
©Turn off the power, wait five seconds, and then turn back on
the power (see page 28).
Rough or scratchy sound is heard. High range is not clear.
• Turntable needle is dirty or worn, or a problem exists with a
connected component.
• Internal fuse is blown.
©Contact your Integra/Onkyo Service Center.
©Refer to the instruction of the connected components and
check for problem.
• Treble control is too high.
©Turn treble setting down at Setup Menu → Audio Adjust
Menu → Tone Control Sub-menu (see page 53).
Power turns on but no sound.
• “Muting” is displayed.
©Press the MUTING button on the remote controller to turn off
muting (see page 30).
• Bad connections or wiring.
©Check connections, speaker cables, and other wiring (see
pages 15 to 27).
FM/AM TUNER
• Amplifier protection circuitry is activated.
©Contact your Integra/Onkyo Service Center.
AM stations cannot be received.
• AM loop antenna is not connected.
Sound of playback source is not heard.
©Connect the included AM loop antenna to the AM antenna
terminals (see page 22).
• Input selector is not set properly.
©Set to correct input source.
Buzzing noise on AM stations (particularly noticeable at
night or with weak stations).
• Headphones are connected.
©Lower volume and then disconnect headphones.
• Noise from electrical apparatus such as fluorescent lamp.
©Move the AM loop antenna to different position.
©Set up an outdoor AM antenna (see page 23).
Power shuts off immediately after power on.
• Amplifier protection circuitry is activated.
©Remove the power cord from outlet immediately. Contact
your Integra/Onkyo service center.
Noise is heard at high-pitched sounds on AM stations.
• Noise caused by TV set.
©Place the AM loop antenna as far as possible from the TV.
©Move DTR-7.3 away from TV set.
Crackling noise on both AM and FM stations.
SPEAKERS
• Noise caused by fluorescent lamp being turned on and off.
©Move antenna as far as possible from the fluorescent lamp.
No sound from the center speaker, or at very low
volume.
• Noise from automobile ignition.
©Install an FM outdoor antenna as far as possible from the road
(see page 23).
• Speaker cable is not connected.
©Check the connection between amplifier and speaker (see
page 20, 21).
©Change the position or direction of the outdoor antenna.
• Listening mode is set to Stereo or Direct.
©Set the Listening mode to any mode other than Stereo or
Direct. The output to the center speaker may differ depending
on the listening mode.
Stereo indicator lights, but sound is distorted and stereo
separation is bad.
• Station is too strong.
©Change to FM indoor antenna (see page 22).
• Center speaker volume is set to minimum.
©Set the center speaker level to the appropriate volume (see
page 45).
• Multiple reflection of the radio waves because of tall buildings
or mountains.
©Use antenna that has better directivity and orient it so
distortion is least.
• The Center setting is set to “None.”
©Set the Center setting to “Large” or “Small” at Setup Menu →
Speaker Setup Menu → Speaker Config Sub-menu (see page
43).
Indicators for stereo reception flicker and hiss is heard
on FM stations.
• Station is too weak.
No sound or very low volume from subwoofer.
©Install an outdoor FM antenna (see page 23).
• Subwoofer setting is set to “No.”
• Stereo FM broadcasts cover only about half the distance of an
ordinary broadcast.
©Change the position or direction of the outdoor antenna.
©Set the Subwoofer setting to “Yes” at Setup Menu → Speaker
Setup Menu → Speaker Config Sub-menu (see pages 43, 54).
• Subwoofer volume is set to minimum.
©Set the subwoofer level to the appropriate volume (see page
45).
No preset station is recalled.
• Memory is lost because power has been turned off for a long time.
©Store all stations again (see page 35).
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
VIDEO and AUDIO
OTHER
Desired picture does not appear.
LATE NIGHT function cannot be used.
• Improper connection.
©Check connections. Insert the plugs and connectors
completely (see pages 16, 19).
• Playback source is not Dolby Digital encoded.
©Check that the DOLBY DIGITAL indicator lights up on the
display.
• Video Setup Sub-menu settings are incorrect.
©Check settings at Setup Menu → Input Setup Menu → Video
Setup Sub-menu (see page 48).
Re-EQ function cannot be used.
• Listening mode is set to Theater-Dimensional, THX, or Direct/
Pure Audio.
No OSD Menu display.
©Select different listening mode (see page 58).
• Improper connection.
©Check connections (see pages 17).
Desired parameter cannot be set.
• Parameter may not be able to be set due to current listening
mode.
©Check settings in Audio Adjust Menu (see page 58).
• OSD Menu is displayed when monitor is connected to VIDEO or
S VIDEO of MONITOR OUT.
©Check connections (see page 17).
Multichannel audio is not output.
Audio and video do not match.
• The Multichannel setting is set to “No.”
©Set the Multichannel setting to “Yes” at Setup Menu → Input
Setup Menu → Multichannel Setup Sub-menu (see page 47).
• Improper connection.
©Check connections (see page 16, 19).
• Video Setup Sub-menu settings are incorrect.
©Check settings at Setup Menu → Input Setup Menu → Video
Setup Sub-menu (see page 48).
• Input source is not connected to MULTI CHANNEL INPUT
port.
©Check connections (see page 27).
Audio is not heard or audio from different source is
heard.
Components in remote zone (Zone 2) do not operate
properly.
• Digital Setup Sub-menu settings are incorrect.
©Check settings at Setup Menu → Input Setup Menu → Digital
Setup Sub-menu (see page 46).
• Components are incorrectly connected.
©Check connections.
• Objects are interfering with remote controller signals.
©Move inferring objects away from path of remote controller
signals.
No picture appears on the TV screen (or monitor).
• TV (or monitor) is not set to receive the output signals from the
receiver.
©Set the TV (or monitor) to the receiver input.
Sound is sometimes heard and sometimes not heard
with digital sources.
• Video cable is not connected securely.
©Check connections (see pages 16, 19).
• One digital input format has been specified so other digital
formats are not played.
• Input source is connected to the COMPONENT VIDEO IN
connectors.
©Make sure TV (or monitor) is connected to COMPONENT
VIDEO OUT connectors (see page 17).
©Select “All” at Setup Menu → Input Setup Menu → Digital
Setup Sub-menu → Digital Format (see page 47).
Noise during playback or skipping of the beginning
sounds occurs with DTS sources, PCM sources, and
other digital sources.
• When “All” is set for the digital format setting, time is required
to change formats when different sources are played.
©Try specifying the format you are playing at Setup Menu →
Input Setup Menu → Digital Setup Sub-menu → Digital
Format (see page 47).
REMOTE CONTROLLER
Front panel controls function but remote controller
controls do not.
The unit cannot be switched to Dolby EX or DTS-ES
mode.
• No batteries in remote controller.
©Insert batteries (see page 7).
• “Surr Back/Zone 2” is set to “Zone 2.”
• Batteries have worn out.
©Change the “0. Hardware Setup → 0-2. Surr Back/Zone 2
©Replace batteries (see page 7).
Sub-menu” setting to “Surr Back.” (See page 41)
• Remote controller is not pointed at the remote sensor of the
DTR-7.3.
• The “Surr Back” setting is set to “None.”
©Set the “Surr Back” setting to “Large” or “Small” at Setup
Menu → “1. Speaker Setup Menu” → “1-1. Speaker Config
Sub-menu” (see page 43).
©Point the remote controller at the remote sensor of the DTR-
7.3 (see page 7).
• Remote controller is too far from the DTR-7.3.
©Operate the remote controller within 16 feet (5 meters) (see
page 7).
• Remote controller is functioning in a different mode
©Press the RCVR Mode button.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
If one of the messages shown below appears
“Not available with headphones use”
Operation not allowed because headphones are plugged into the
DTR-7.3.
“Not available with Multichannel use”
Operation not allowed while the multi-channel output is being used.
“Not available in this Sp Config”
Will not work with the current speaker configuration settings.
“Not available in Zone 2 mode”
Setting not allowed because the Zone 2 mode is turned on.
“Only available with Dolby D”
No setting other than Dolby Digital can be set.
“Not available in this Listening mode”
Will not work with the current listening mode.
“Not available with this signal”
The listening mode cannot be selected with the current input source.
“Not available in PURE AUDIO mode”
Will not work with the PURE AUDIO mode.
“Surr Back/Zone 2 setting is Surr Back”
Operation not allowed because the setting is Surr Back.
“Surr Back/Zone 2 setting is Zone 2”
Operation not allowed because the setting is Zone 2.
“Not available with this Surr Back/Zone 2 setting”
Will not work with the current setting.
“Not available with Muting”
Operation not allowed because the muting is activated.
“Zone 2 is not On”
Will not work because the Zone 2 has not been turned on.
Also refer to the respective instruction manuals of the CD player,
DVD player, video cassette recorder, TV monitor, etc., that compose
your entertainment system.
The DTR-7.3 contains an internal microcomputer that performs
high-level operations. However, on extremely rare occasions, noise
or interference from an external source or static electricity may cause
faulty operation. If this occurs, unplug the power cord from the wall
outlet, wait five or more seconds, and then plug it back in. This
should correct the situation.
* To reset the surround mode and other settings to the factory
default settings, hold down the VIDEO 1 button with the DTR-
7.3 turned on and then press the Standby/On button. “CLEAR”
appears in the front display and the DTR-7.3 enters the standby
state.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
AMPLIFIER SECTION
TUNER SECTION
Continuous average power output (FTC)
FM
All channels:
100 W per channel min. RMS at 8
Tuning range
USA & Canadian models:
Australian models:
Usable sensitivity
Mono:
Ω, 2 channels driven from 20 Hz to
20 kHz with no more than 0.08%
total harmonic distortion.
130 W min. RMS at 6 Ω, 2 channels
driven from 1 kHz with no more
than 0.1% total harmonic
distortion.
87.5–108.0 MHz (100-kHz steps)
87.50–108.00 MHz (50-kHz steps)
11.2 dBf, 1.0 µV (75 Ω IHF)
0.9 µV (75 Ω DIN)
17.2 dBf, 2.0 µV (75 Ω IHF)
23 µV (75 Ω DIN)
Stereo:
Continuous power output (DIN)
Maximum power output (EIAJ)
Dynamic power output (stereo)
135 W at 6 Ω
50 dB quieting sensitivity
Mono:
Stereo:
160 W at 6 Ω
17.2 dBf, 2.0 µV (75 Ω)
37.2 dBf, 20 µV (75 Ω)
2.0 dB
2 × 250 W at 3 Ω
2 × 210 W at 4 Ω
Capture ratio:
2 × 130 W at 8 Ω
Image rejection ratio
USA & Canadian models:
Australian models:
IF rejection ratio:
Signal-to-noise ratio
Mono:
Total harmonic distortion:
IM distortion:
0.08% at rated power
40 dB
85 dB
90 dB
0.08% at 1 W output
0.08% at rated power
0.08% at 1 W output
60 at 8 Ω
Damping factor:
Input sensitivity and impedance
PHONO:
LINE (CD, TAPE, DVD,
VIDEO 1-5):
MULTICHANNEL INPUT
(FRONT L/C/R, SURROUND
76 dB
70 dB
55 dB
50 dB (DIN)
50 dB
Stereo:
2.5 mV, 50 kΩ
200 mV, 50 kΩ
Alternate channel attenuation:
Selectivity:
AM suppression ratio:
Total harmonic distortion
Mono:
0.2%
L/R, SURROUND BACK L/R): 200 mV, 50 kΩ
Stereo:
Frequency response:
Stereo separation:
0.3%
(SUBWOOFER): 36 mV, 50 kΩ
30 Hz–15 kHz, 1.0 dB
45 dB at 1 kHz
30 dB at 100 Hz–10 kHz
COAXIAL 1, 2, 3 (DIGITAL): 0.5 Vp-p, 75 Ω
DVD, VIDEO 1, 2, 3, 4, 5:
1 Vp-p, 75 Ω
1 Vp-p, 75 Ω (Y)
0.28 Vp-p, 75 Ω (C)
1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (PB, PR)
AM
Tuning range
COMPONENT VIDEO 1, 2:
USA & Canadian models:
Autralian models
Usable sensitivity:
Image rejection ratio:
IF rejection ratio:
Signal-to-noise ratio:
Total harmonic distortion:
530 to 1,710 kHz (10-kHz steps)
522 to 1,611 kHz (9-kHz steps)
Output level and impedance
Rec out (TAPE, VIDEO 1, 2):
30 µV
40 dB
40 dB
40 dB
0.7%
200 mV, 470 Ω
1 V, 470 Ω
Pre out:
VIDEO (VIDEO 1, 2, MONITOR
OUT, ZONE 2 OUT):
1 Vp-p, 75 Ω
GENERAL
Power supply
USA & Canadian models:
Australian models:
Power consumption
USA & Canadian models:
Australian models:
1 Vp-p, 75 Ω (Y)
0.28 p-p, 75 Ω (C)
AC 120 V, 60 Hz
AC 230–240 V, 50 Hz
COMPONENT VIDEO OUT: 1 Vp-p, 75 Ω (Y)
0.7 Vp-p, 75 Ω (PB, PR)
Phono overload:
Frequency response:
120 mV RMS at 1 kHz, 0.5% T.H.D.
5 Hz to 100 kHz : +1/–3 dB
(CD in Direct mode)
8.1 A
655 W
Dimensions (W × H × D):
435 × 175 × 460 mm
17-1/8" × 6-7/8" × 18-1/18"
38.4 lbs. (17.4 kg)
RIAA deviation:
20 Hz to 20 kHz : 0.8 dB
Tone Control
Weight:
Bass:
10 dB at 50 Hz
Treble:
10 dB at 20,000 Hz
REMOTE CONTROLLER
Signal-to-noise ratio (Direct)
Phono:
Line:
Transmitter:
Signal range:
Power supply:
Infrared
Approx. 16 ft., 5 meters
Two “AA” batteries (1.5 V × 2)
80 dB (IHF A, 5 mV input)
110 dB (IHF A, 0.5 V input)
Due to setup menu
Muting:
Specifications and features are subject to change without notice.
Integra Division of
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-831-8124
Printed in Japan
D0210-1
SN 29343422
Download from Www.Somanuals.com. All Manuals Search And Download.
DTR-7.3
How to Enjoy Net Audio
Features
System Requirements
The DTR-7.3 is a network audio client that is connected via a LAN to a
server NAS-2.3 and allows you to enjoy music files saved on the server
NAS-2.3, as well as Internet radio, from anywhere in your home.
Requirements for listening to both Internet radio stations
and music files saved on the music server
I Modem (a device that provides Internet connections via leased lines;
e.g., a cable modem, xDSL modem, terminal adapter)
* To have access to Internet, you typically need to make a contract
with an Internet service provider (ISP). Modem requirements differ
from ISP to ISP; for detailed information, consult with your ISP or
PC retailer.
Internet radio features
The DTR-7.3 provides enhanced support for Internet radio and allows
you to:
I Router (gateway) (a device that enables multiple PCs or devices to
•
Listen to both WMA and MP3 audio streamed from Internet radio
stations
connect to the Internet simultaneously)
An IP address can be obtained automatically by using the router’s
DHCP function.
•
•
Select stations by genre, location, or language
Preset up to 30 Internet radio stations
* Some routers have built-in modem functionality. Router
requirements differ from ISP to ISP; for detailed information,
consult with your ISP or PC retailer.
Net-Tune Features
I Ethernet CAT-5 cable
The NAS-2.3 distributes music files through LAN to the DTR-7.3.
The DTR-7.3 plays distributed music data whenever you need.
I Minimum Internet Connection Requirements:
•
•
Broadband Internet Connection
In the connection between the NAS-2.3 and the DTR-7.3, the standard
TCP/IP network protocol and the Integra/Onkyo’s proprietary NTSP
protocol is used for music distribution through LAN. The NTSP protocol
handles not only data for music itself but also additional music
information including the name of tracks and artists, enabling high
usability.
DHCP (Dynamic Host Configuration Protocol) based network
(requires a DHCP-enabled router)
•
100Base-TX switch built-in broadband router (recommended)
Notes:
•
To enjoy music on Internet Radio, it is assumed that you provide a
The NAS-2.3 supports WAVE (PCM) and MP3 formats. The WAVE
format has high sound quality (equivalent to CD) with no compression.
The MP3 format is widely used through Internet environment and has
near-CD quality with compression.
broadband Internet connection on which you can successfully run a
web browser. If you have any problem in connecting to the Internet,
consult with your ISP.
•
•
•
If your ISP contract assumes manual configuration of network
settings, you need to manually configure your network settings as
described in “Network Setup Menu” (see page 6).
Hint:
File Format: MP3/WMA (Approximately 1 MB for 1 minute)
WAVE (Approximately 10 MB for 1 minute)
The DTR-7.3 does not support network settings for PPPoE
connections; if your ISP contract requires PPPoE, therefore, you
must have a gateway/router with PPPoE support.
* How much free space is actually required also depends somewhat on
such factors as the format and reserved space of your hard disk, and
the bit rate at which you make recordings.
You may have to set up a proxy server to listen to Internet radio,
depending on the ISP you choose. If your PC is configured to use a
proxy server for Internet access, the DTR-7.3 must also be
configured the same way. For more information, see “5-2. Proxy
Setup Sub-menu” (see page 7).
* Depending on the MP3 encoder you use, your recorded file may not
be playable, or can play the music degraded by noise, or can
generate uncomfortable sound.
•
The DTR-7.3 is designed to take advantage of the DHCP and AutoIP
functionality, thereby automatically configuring the network
settings. If you opt not to use the DHCP and AutoIP functionality,
you should manually configure the network settings. For more
information, see “5-1.IP Address Sub-menu” (see page 7).
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the DTR-7.3 to your Ethernet Network
Plug one end of an Ethernet CAT-5 cable into the port on the backside of the DTR-7.3 and the other end into the gateway.
Internet
LAN port/
Ethernet, etc
NAS-2.3
COMPONENT
VIDEO
FRONT SPEAKERS
SURR SPEAKERS
OUTPUT
AV RECEIVER
MODEL NO. DTR 7.3
R
L
R
L
Y
-
Modem
PB
NETWORK
AC OUTLETS
PR
INPUT 1
Y
To the WAN side
:
CAUTION
SURR
SPEAKER
CENTER
SPEAKER
BACK/
ZONE 2
PB
IMPEDANCE
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
AC 120V 60Hz
SWITCHED
SPEAKERS
TOTAL 120W 1A MAX.
PR
SEE INSTRUCTION
MANUAL FOR
R
L
INPUT 2
Y
To the LAN
side port
CORRECT SETTINGS.
IR
AC INLET
A
ZONE 2
12V
TRIGGER OUT
IN
RS232
P
B
R
P
OUT
REMOTE
CONTROL
B
To the LAN side port
DTR-7.3
Router
Internet radio
Hint:
Connecting more than one unit of DTR-7.3 to a router enables several
users to listen to Internet radio at different stations or different music
pieces contained in the same library on the NAS-2.3.
NAS-2.3
Modem
To the WAN side
To the LAN side port
To the LAN side port
To the LAN side port
Router
Room 1
Room 2
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Music on Internet Radio or NAS-2.3
/ /
Enter
Net A
Setup
Enter,
Display
Random
Album
Repeat
Playlist
Artist
Genre
Alphanumeric keys
Net Audio
* In the NET AUDIO mode, buttons
will function according to the
associated labels printed in blue.
Enjoying Internet radio
7. Press the Enter button.
Buffering starts with the following message displayed.
To listen to Internet radio, the connection/configuration requirements
listed on pages 1, 2 must be satisfied. When you perform the step 2 and
following steps, use the remote controller.
When the buffering completes, the DTR-7.3 starts playback of the
broadcast.
1. Press the Net Audio button (on the main unit) or the
Net A button (on the remote controller).
Calls the setting used last time. If you want to listen to Internet radio
immediately after using the NAS-2.3, you can switch to Internet
radio by pressing the same button again. It will take some time until
the connection is established.
Note:
If you are connected to the Internet via a slow link (such as a dial-up
connection) rather than a broadband link (via an xDSL or cable modem), you
may not be able to enjoy Internet radio as you expect or at all.
2. Press the Display button on the remote controller.
You can switch the displayed content using the
/
buttons.
After the switch operation, the display mode appears for 3 seconds, and
then the appropriate information scrolls.
3. Use the
/
buttons to select one of the main menu;
If there is no information on title or artist, “No Info” appears.
When using the OSD screen, all the information is displayed on one
screen without scrolling.
Genres, Location, or Language.
To cancel, press the button.
4. Press the Enter button.
OSD
iNet Radio Station ONK
7ch
Wait while your requested data is download from the XiVA
Internet Radio Service.
Track:
Program:
Artist:
Data:
Station ONK Live
Station ONK Live
RealOnkyoNet.com
WMA 20kbps
* What is the XiVA Internet Radio Service?
The XiVA Internet Radio Service provides tuning information,
allowing you to select from a large number of stations. You can
find Internet Radio Stations based on your interests, musical taste,
language and location.
Tuned
When Genres is selected:
Allow a few moment until the Genre menu appears. When the main
list of genre appears, use the
desired. Pressing the Enter button brings up the sub-list of the genre
you selected, which prompts you to further select one of the items
/
buttons to select a genre as
Display
using the
/
buttons.
I
Presetting Internet radio stations:
When Location is selected:
The list containing names of countries appears. Use the
to select an item as desired.
You can preset up to 30 internet radio stations.
/
buttons
1. Receive your desired station.
When Language is selected:
The list of languages appears. Use the
desired item.
2. Press the button.
/
buttons to select your
The DTR-7.3 enters into preset mode; the currently selected preset
number flickers for 5 seconds.
If no list is found, “No List” appears.
You can return from this screen to the previous selection screen by
pressing the button.
Preset number
ch
5. Press the Enter button.
You are presented with a list of radio station names.
3. Press the Enter button.
6. Use the
/
button to select one of the radio stations.
Now the preset is complete.
You can return to the previous step by pressing the button.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Music on Internet Radio or NAS-2.3
I
Choosing a preset Internet radio station:
4. Press the
button to play the music file.
1. Press the Net Audio button (on the main unit) or the
Net A button (on the remote controller).
The DTR-7.3 provides five normal display modes; you can use the
/
button to switch among them.
Calls the setting used last time.
OSD
Music Server
Track: 1/12
Play
If you want to listen to Internet radio, you can switch to Internet
radio by pressing the same button again.
1m20s>
My sweet candy
Album:
Artist:
Data:
My Best 100
2. Press the CH
button.
Happy PanPot
MP3 160kbps
When you choose a preset station, the station name is displayed for 5
seconds, and then the progress of buffering is displayed instead.
Display
•
•
•
To stop playback:
Press the button on the remote controller.
When the progress of buffering reaches 100%, you will be presented
with the playing screen.
To pause playback:
I
Erasing a preset Internet radio station:
Press the button on the remote controller.
1. Select the station to erase, following the instructions
described above.
To select a track:
Press the
Press the
/
button on the remote controller.
2. Press the button.
button to move to the next track.
Press the
hold down the
button to move to the beginning of the current track;
button to move to the previous track.
You can also use the Alphanumeric keys to select a track.
ex.
The DTR-7.3 enters into preset erase mode.
3. Press the Enter button.
To select number 3, press 3.
Your selected station is erased.
To select number 10, press 0.
To select number 37, press --/---, 3 and 7.
To select number 123, press --/--- twice, and then press 1, 2, and 3.
Playing a music file saved in NAS-2.3
•
•
To fast-forward/reverse the music:
To play music files saved in NAS-2.3, the requirements listed on page 1
must be satisfied.
Press and hold the
forward the music; press and hold the
button on the remote controller to fast-
button to fast-reverse the
music. When the music is rewound to the beginning, normal playing
starts.
1. Turn on the NAS-2.3
Wait for a while until NAS-2.3 starts up.
It may take a few minutes.
To switch to the track list:
While playing the music, you can press the cursor button to
display a list of currently open tracks.
2. Turn on the DTR-7.3.
When you connect the DTR-7.3 to the network first time, it will be
connected to the server found first.
3. Press the Net Audio button (on the main unit) or the
Net A button (on the remote controller).
If you want to play a music file immediately after listening to Internet
radio, you can switch it by pressing the same button again. The track
you played the last time is called up so that you can play it again.
Until the DTR-7.3 connects to the network, finds the server and
completes the connection, “Network Starting...” and
“Connecting...” appears. After completing the connection to the
NAS-2.3, the display changes to the normal indication.
If the following messages appear, check the message meaning and
perform the appropriate procedures.
“No Track”
The NAS-2.3 could not retrieve any track information. Register
tracks with the NAS-2.3.
If you have already registered tracks, use the Display, Artist, Album,
Genre, and Playlist buttons to display information.
“Disconnected”
The NAS-2.3 may not start or it may not be found. Make sure the
connections between router, NAS-2.3 and the DTR-7.3. Start the
NAS-2.3.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Music on Internet Radio or NAS-2.3
I
Playing a music file at random:
When the numeric value is selected:
Pressing the button once will perform the search by the numeric value
“2.”
Press the Random button on the remote controller while playing
stops.
Pressing the Random button on the remote controller displays the current
random settings.
Symbols
This button switches between two alternative settings: On and Off.
On: Randomly plays the tracks in the currently selected mode.
Off: Random mode is disabled.
Caps
After necessary settings complete, press the
button.
I
Playing a music file repeatedly:
3. Press the Enter button.
Press the Repeat button on the remote controller.
Pressing the Repeat button on the remote controller displays the current
repeat settings.
This button cyclically switches among three alternative settings: Repeat
1 → All → Off.
The title of your selected track appears.
You can choose another track by pressing the
/
buttons.
Press the button to return to the previous step.
You can also select the list number using the numeric buttons.
Repeat 1: Repeats the current track only.
Repeat All: Repeats the tracks in the currently selected mode.
4. Press the Enter button.
Repeat Off: Repeat mode is disabled.
You can operate the DTR-7.3 when playing and stopped.
The playback begins.
To cancel the operation:
I
Selecting a track list:
You can use the music file data saved in the NAS-2.3 to select which
tracks to play.
Press the button to return to the previous step. You can cancel the
whole operation by pressing the button in step 1.
For example, you can:
Note:
• Select a track list based on the album name
• Select a track list based on the artist name
• Select a track list based on the genre name
• Select a play list
Pressing Display button on the main unit will display the current
listening mode.
1. Press either the Album, Artist, Genre, or Playlist
button on the remote controller.
Search the track stored in NAS-2.3 with your selected mode to
display it in the display.
In the artist and album modes, the tracks are displayed in
alphabetical order.
You can also use the procedure below.
1. Press the Display button
2. You can press the
four modes: Albums
/
buttons to cyclically switch among the
Artists Genres Playlists.
3. Press the Enter button
2. Use the buttons to select one of the menu.
/
At this time, pressing button brings you one step behind where
you can change the selection you made.
Also, pressing button in the genre or artist selection mode will
display a list of albums with the genre or artist you selected.
In the album, artist or playlist selection mode, using the
Alphanumeric buttons will accelerate your selecting operation.
Using the Alphanumeric keys
The alphanumeric keys allow you to input one of the letters or numbers
printed on their key tops. Pressing the CAPS button cyclically switches
the types of input; Upper case (A) → Lower case (a) → Numeric value
(1) →... When your desired input type is selected, then press the
alphanumeric key.
Let us take the 2ABC button for example to see how it can be operated.
When the upper case is selected:
Pressing the button once will perform the search by the letter “A.” Pressing
twice will do the search by “B,” pressing three times by “C.”
When the lower case is selected:
Pressing the button once will perform the search by the letter “a.”
Pressing twice will do the search by “b,” pressing three times by “c.”
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ConfiguringVarious Settings
Navigating through the Setup Menu:
Be sure to press the RCVR button before using the remote controller.
Network Setup Menu
Before you can use the DTR-7.3 to play music contained in the music
library in the NAS-2.3 and listen to Internet radio, you must correctly
configure the DTR-7.3’s network settings so that it can connect to your
LAN and the Internet.
It is strongly recommended to use a broadband connection (via an xDSL
or CATV leased line) and a router. If you are connected to the Internet
via a narrowband dialup connection, you may not be able to enjoy
Internet radio as you expect or at all.
1. Press the Setup button.
2. Using the
and
cursor buttons, select the menu
that you want to enter.
3. Press the Enter button to enter the selected menu.
Before setting up the DTR-7.3, make sure that you are already using a
router that provides Internet access and that the DTR-7.3 is correctly
connected with your router or hub via a LAN cable.
4. Use the and cursor buttons to select the sub-menu
that you want to enter and press the Enter button.
For more information on Internet connectivity, consult with your ISP
(Internet Service Provider) or refer to the documentation of your router.
Each sub-menu has different settings that can be changed as desired,
and they are all explained in the pages that follow. To change a
setting, first select it using the and cursor buttons, and then
change the setting using the and cursor buttons.
Advanced Menu
5.Network Setup
5. Press the Return button to set the new settings and
return to the previous menu screen.
5-1.IP Address
a.DHCP/AUTO-IP:On
b.IPAddress
Press the RETURN button again to return to the main menu.
Advanced Menu
:192.168.9. 62
c.SUBNET Mask
:255.255.255. 0
5.Network Setup
d.Gateway
Input Setup Menu (When NET AUDIO is selected
as the input source)
:192.168. 9. 1
DNS Server
e.1st:210.134.143. 7
f.2nd:125. 40.104. 0
5-2.Proxy Setup
a.ProxyServer
:On
b.Proxy Address
When NET AUDIO is selected as the input source, you can set up Music
Server on this screen.
c.Proxy Port
: 8080
Advanced Menu
2-1.Music Server
Input:NET A
2-2.Playback OSD Display
Input:NET A
5.Network Setup
Quit:|SETUP|
a.Select Server
:NAS-2.3
a.Playback OSD Display
:Full
1.IP Address
2.Proxy Setup
3.MAC Address
4.Client Setup
→OK
→Save settings
Advanced Menu
5.Network Setup
|ENTER|Quit:|SETUP|
Quit:|SETUP|
Quit:|SETUP|
5-3.MAC Address
a.MACAddress
:XX:XX:XX:XX:XX:XX
Advanced Menu
5.Network Setup
2-1. Music Server Sub-menu
a. Select Server
Select the NAS-2.3 that exists on the network.
5-4.Client Setup
a.ClientName
:TX-NR9000102
b.WakeuponLAN
:On
c.NTSPPort
:XXXXXX
Quit:|SETUP|
* mark appears to the servers detected on the network. If there is a server
which does not have * mark, make sure that the server is started.
After selection, use the button to select “→ OK”, and press the Enter
button to confirm your selection.
Quit:|SETUP|
2-2. Playback OSD Display Sub-menu
a. Playback OSD Display
Full: Select this when you want to have the OSD display the
information on the currently played track.
Simple: Displays the current track information summary in two
lines.
DHCP (Dynamic Host Configuration Protocol) and AutoIP are
mechanisms for network configuration, which assign IP addresses
automatically to the network devices such as the DTR-7.3, PC, and
broadband router.
DNS (Domain Name System) is a mechanism which translates domain
names into IP addresses or vice versa. Domain names such as
210.199.170.69 are used for actual network data transfer.
Off: Select this when you do not want to have the information
displayed on the OSD.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Various Settings
5-1. IP Address Sub-menu
5-2. Proxy Setup Sub-menu
You can use this submenu to turn on/off the DHCP and Auto IP
functionality.
Configure this item if your DTR-7.3 uses a proxy server to connect to the
Internet.
Also, you can use this menu to manually configure network settings.
Referring to the documentation from your ISP, enter the IP address and
subnet mask assigned to your DTR-7.3 as well as the IP addresses of the
default gateway and DNS server.
After necessary settings complete, press the Return button to go back to
“5. Network Setup Menu”, select “→ Save Settings”, and press the Enter
button to save the setting you made.
When you set a.DHCP/AUTO IP to Off, select an menu item under b.
and press the Enter or button, the DTR-7.3 enters the number-entry
mode.
Enter the proxy server settings exactly as specified by your ISP.
After necessary settings complete, press the Return button to go back to
“5. Network Setup Menu”, select “→ Save Settings”, and press the
ENTER button to save the setting you made.
a. Proxy Server
Sets whether the DTR-7.3 connects to Internet radio station through
proxy server or not.
On: Connects to Internet radio station through Proxy Server.
Off: Connect to Internet radio station without Proxy Server.
Select a number using the
enter the number.
/
buttons, and press the Enter button to
b. Proxy Address
Enter the domain name of the proxy server.
When you set a.Proxy Server to On, select this menu item and press the
ENTER or button, the DTR-7.3 enters the character-entry mode.
After all the necessary numbers are entered, the DTR-7.3 exits the
number-entry mode.
a. DHCP/AUTO IP
Sets whether the network setting is configured automatically or not.
Select a character using the
button to enter the character.
/
/
/
buttons, and press the ENTER
After all the necessary characters are entered, the DTR-7.3 exits the
character-entry mode.
On: The network setting will be configured automatically. When you set
this option to On, the values for b. through f. will be assigned using
DHCP.
c. Proxy Port
Enter the port number of the proxy server.
Off: The network setting is configured manually.
When you set a.Proxy Server to On, select this menu item and press the
ENTER or button, the DTR-7.3 enters the number-entry mode.
b. IP Address
You will enter this value when you set the a.DHCP/AUTO IP setting
above to Off.
Select a number using the
/
/
/
buttons, and press the ENTER
button to enter the number.
After all the necessary numbers are entered, the DTR-7.3 exits the
number-entry mode.
Enter the IP address assigned to your DTR-7.3. If your DTR-7.3 is
directly connected with an xDSL modem or terminal adapter, be sure to
enter the static IP address exactly as specified by your ISP.
Specify the IP address within the range below. The NAS-2.3 cannot be
used with the IP addresses out of the ranges below.
Note:
After setting, allow approx. 2 seconds until the DTR-7.3 stores all of the
data in the memory. Be sure not to turn off the power during that time
otherwise the data will be lost.
CLASS A: 10.0.0.0–10.255.255.255
CLASS B: 172.16.0.0–172.31.255.255
CLASS C: 192.168.0.0–192.168.255.255
Because the most of the routers commercially available is set to the
CLASS C IP address, specify the CLASS C IP address for the DTR-7.3.
5-3. MAC Address Sub-menu
You can view the assigned MAC address. Every network port is
identified by a unique MAC address. (This is read-only information.)
c. SUBNET Mask
You will enter this value when you set the a.DHCP/AUTO IP setting
above to Off.
Enter the subnet mask. If your DTR-7.3 is directly connected with an
xDSL modem or terminal adapter, be sure to enter the subnet mask
exactly as specified by your ISP. Usually, enter 255.255.255.0 here.
a. MAC Address
Displays the MAC address assigned to your DTR-7.3.
d. Gateway
You will enter this value when you set the a.DHCP/AUTO IP setting
above to Off.
Enter the IP address of the default gateway. If your DTR-7.3 is directly
connected with an xDSL modem or terminal adapter, be sure to enter the
gateway address exactly as specified by your ISP. If your DTR-7.3 is
connected to a gateway/router, enter the IP address of the gateway/
router.
DNS Server
e. 1st
f. 2nd
You will enter this value when you set the a.DHCP/AUTO IP setting
above to Off.
Enter the IP address of the DNS server. If your DTR-7.3 is directly
connected with an xDSL modem or terminal adapter, be sure to enter the
DNS address exactly as specified by your ISP.
When your Internet service provider provides only one DNS address
with you, enter this address into “e.1st”. When two or more DNS
addresses are provided, enter two of them into “e.1st” and “f.2nd”
respectively.
Note:
After setting, allow approx. 2 seconds until the DTR-7.3 stores all of the
data in the memory. Be sure not to turn off the power during that time
otherwise the data will be lost.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Various Settings
Appendix
5-4. Client Sub-menu
Troubleshooting guide
A client is a device that receives information from a sever. One server
can serve multiple clients.
Throughout this guide, the term “client” refers to your DTR-7.3
Pressing the Net Audio button on the main unit (or the Net
A button on the remote controller) fails to activate the
Internet radio or music server feature.
a. Client Name
Shows the name used on the NAS-2.3.
The client name already has been set by the DTR-7.3.
•
Imperfect network connection.
© Check the connection between this unit and the LAN side port of
your router (gateway).
© Make sure that the modem and router (gateway) are correctly
connected. Also, make sure that the power is on.
© Make sure that the Network Setup is configured properly.
b. Wakeup on LAN (Network connection status)
Sets whether leaves the network connection open or not while the DTR-
7.3 is in the standby state.
The playback sound discontinues while using the Music
Server.
On: Leaves the network connection open.
Off: Closes the network connection while the DTR-7.3 is in the
standby state. You can save the power consumption during standby
state.
•
Excessive load on the network or server. Or processor-intensive
applications including word processor and spreadsheet are running.
© Make sure that your system satisfies all the system requirements
listed on page 1.
c. NTSP Port
You can change the TCP/IP port number used for communicating with
the NAS-2.3. Be sure to match the port number set here with the port
number set on the NAS-2.3.
© When you play WAVE files on multiple DTR-7.3, the playback
sound may discontinue because of network overload. In this case,
deploying another independent LAN dedicated to the Net Audio to
separate from general LAN connection, or adding switching hub or
router to improve network traffic may resolve the problem.
Select a number using the
button to enter the number.
/
/
/
buttons, and press the ENTER
After all the necessary numbers are entered, the DTR-7.3 exits the
number-entry mode.
The unit fails to obtain a station list from an Internet radio
site (via the XiVA internet Radio Service).
•
The radio site is now out of service or otherwise inaccessible due to
some other reason such as maintenance.
© Try to access the site after a while.
→ Save Settings
Select “Save Settings” using the
/
button, and press the button to
save the settings made at 5-1. through 5-4.
Never turn off the DTR-7.3 while saving the settings.
Selecting the “Music Server” fails to play music or fails to
connect to the server.
•
•
•
The NAS-2.3 is not turned on.
© Turn on the NAS-2.3.
No audio files found on the server.
© Create MP3 and/or WAV audio files on the NAS-2.3.
The network is down because of some failures.
© Unplug the power cord of the DTR-7.3 and plug it again.
If this does not resolve the problem, turn off the power of the NAS-
2.3 and turn it on again.
•
The NTSP Port setting on the DTR-7.3 differs from that of NAS-2.3.
© Go to “5-4.Client Setup Sub-menu”, select “c.NTSP Port”, then
set the same value as used for NAS-2.3.
Search by album returns no match.
•
The audio file list of NAS-2.3 contains no files that have album names.
© Assign album names to the files contained in the audio file list of
NAS-2.3.
Search by artist returns no match.
•
The audio file list of NAS-2.3 contains no files that have artist names.
© Assign artist names to the files contained in the audio file list of
NAS-2.3.
Search by genre returns no match.
•
The audio file list of NAS-2.3 contains no files that have genre names.
© Assign genre names to the files contained in the audio file list of
NAS-2.3.
No playlist can be selected.
•
You have not yet created any playlist in NAS-2.3.
© Create playlists in NAS-2.3.
Specifications
Ethernet port: 10BASE-T
Supported audio file format: MP3, WMA, WAV (non-compression,
sampling rates of 32kHz, 44.1kHz, and 48kHz supported).
Printed in Japan
D0210-1
E
SN 29343459
Download from Www.Somanuals.com. All Manuals Search And Download.
|