For Digital Video Camera
GR-DVM90, GR-DVM80,
User’s Manual
ENGLISH
GR-DVX90, GR-DVX80,
WR-DV89U
Marine Case
GR-DVX10, GR-DVX9, GR-DVX8
Names of the parts
Mounting method and operating method
for each part
3
1. Tighten the camcorder’s grip strap.
1
2. Remove the four buckles on the marine case and open the
2
4
front lid.
Align the marks.
3. Align the mark on the Power Dial
with the “OFF” mark on the marine
case.
PUSH
OFF
4. Set the camcorder’s Power Switch to
RA
ON)
“OFF”, then open the LCD monitor
and insert the camera into the marine
case.
Front glass
3
Place the included anti-fogging silica gel in the gap between
the camcorder and the marine case to prevent fogging in the
marine case.
1.Marine case front lid
2.Main unit
3.Buckle
• Set the camcorder’s MODE Dial to the desired setting.
• If the camcorder’s Operation Switch is set to “ ”, perform
settings as required then insert the camcorder into the marine
START/STOP
SNAP SHOT
4.Power dial
case.
8
Fit the Zoom Lever projection
over the Power Zoom Lever
5.Recording start/stop
button (START/STOP)
6.Snapshot button
(SNAP SHOT)
ZOOM
5. Fit the Zoom Lever projection on
the marine case over the outer
groove of the Power Zoom Lever
on the camcorder, making sure that
it is securely fit.
7.Zoom lever (ZOOM)
8.Grip strap
If the camcorder’s Power
5
6
7
Switch is not set properly when the
camcorder is placed in the marine
case, it could break and/or it could
damage the Power Dial aligning
boss on the marine case.
Strap
Projection
Power
Zoom
Lever
6. Before sealing the marine case, check that there is no sand,
dirt, or other foreign matter on the O-ring mounted on the front
lid or on the O-ring contact surface on the main unit.
Also make sure that the inserted silica gel bag is not pinched. If
you dive with foreign matter trapped
Before use, this unit must be pre-tested
to check if there is any water leakage.
in these areas, water will leak.
Please read before use.
7. Check that the O-ring on the front lid
is correctly mounted in the groove,
then press in the front lid. Flip down
the four buckles in the directions
This marine case is a precision instrument designed to permit safe
video recording under high water pressure. Please pay careful
attention when handling the unit before and after use, as explained
in this user’s manual.
indicated by the arrows in the figure
on the right to seal the marine case.
Align the marks.
Each part of the marine case has been subject to strict controls
during the manufacturing process, and the individual functions
have faced stringent tests during the assembly process. Each marine
case has also had to pass water-proof inspections using high-
pressure water testers. However, damage can sometimes occur
during transport and distribution, or during storage after purchase,
so before diving always carry out the following pre-use test to
verify safety.
8. Turn the marine case’s Power Dial in
the direction of the arrow while
pressing it down to set the
PUSH
OFF
camcorder’s Power Switch to
A
R
E
)
N
“
”.
• The camcorder’s Power Lamp
lights.
9. To start video recording, press the
Recording Start/Stop Button.
To stop video recording, press it again.
Pre-use test
• Press the Snapshot Button to perform
Snapshot recording. If the flash is used,
its brightness will be darker than usual
due to the marine case. This is normal
and is not a malfunction.
• When recording in the PS-WIDE
mode, a shadow (eclipse) may
appear around recorded images.
Be sure to perform the following pre-use test before diving.
START/STOP
SNAP SHOT
1. Before mounting the camcorder inside the marine case, dive
with only the empty marine case and test for water leaks.
• You can easily check for water leaks at a depth of 1 m, where
there is no water pressure. Be sure to perform this test to
ensure the safety of your camcorder.
2. The following are some common causes of water leaks:
A. The marine case is used without attaching the O-ring.
B. The O-ring is not mounted in the correct position.
C. The O-ring is damaged or deformed.
D. There is sand, dirt, hair or other foreign matter on the O-ring.
E. There is sand, dirt, hair or other foreign matter on the contact
surface of the O-ring or on the inside of the lid.
F. The provided strap or silica gel bag is pinched inside the
marine case when the lid is closed.
To protect your camcorder and ensure optimum use, keep the
examples listed above in mind when using the marine case.
ZOOM
10. The zoom can be adjusted with the
Align the marks.
Zoom Lever.
11. When you are finished shooting, set
the marine case’s Power Dial to
“OFF” (in the direction of the arrow)
while pressing it down to set the
camcorder’s Power Switch to “OFF”.
• The camcorder’s Power Lamp goes
out.
H
S
U
P
OFF
A
R
E
)
N
NOTES:
O-ring
Ⅲ The O-ring is made from rubber and is
mounted on the front lid.
Ⅲ Refer to the camcorder’s instructions for
more information.
JVC accepts no responsibility for water leakage or damage to
anything inside the marine case (camcorder, cassette, etc.) due to
careless usage of this product. Be sure to follow correct procedures
when using the marine case.
LYT0655-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
|