®
SYNTHESIS ARRAY™ MODULE
SAM1HF,
SAM2LF
MODULAR ARRAY
LOUDSPEAKER
’
OWNER S AND
’
INSTALLER S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
®
™
Thank you for purchasing this JBL Synthesis Array Module home theater speaker. This product represents the
synthesis of everything that JBL has learned about the emotional power of audio and video in sixty years of preemi-
nence in the field. It sets new benchmarks in the use of “high technology” and provides you with the experience of
being in some of the world’s greatest movie houses and concert halls, right at home! JBL’s Synthesis Array speaker
systems feature the following:
™
®
THX ULTRA2 -LICENSED HOME AUDIO SYSTEM: When used with a THX controller and amplifiers, your
speaker system will deliver a state-of-the-art THX home theater experience to your living room. You will hear in your
home exactly what the director and sound engineer heard in the recording studio. The system will reproduce the
audio flawlessly and without distortion.
ULTRAHIGH-FREQUENCY COMPRESSION DRIVER: 1" (25mm) Pure-titanium compression driver with aluminum
®
edge-wound voice coil and 2" (51mm) neodymium motor assembly, mounted in a SonoGlass constant-directivity
™
horn for extended high-frequency response to exceed SACD and DVD-Audio specifications.
HIGH-POWER COMPRESSION HORN: Horns are commonplace in movie theaters across the world, because
of their high power handling and well-defined high-frequency output. The horns employed in SAM1HF have very
low distortion and a well-controlled directivity, to put the dialogue at the center of the screen and the effects all
around you.
ACCURATE MID-BASS DRIVERS AND SUBWOOFERS: The 8" (200mm) mid-bass drivers incorporate many of
™
JBL’s patented technologies – such as Symmetrical Field Geometry (SFG), Symmetrical Inductance Modulation (SIM)
™
and Vented Gap Cooling (VGC) – as well as unique cone and dome materials, to provide tight, smooth midrange
sound without harshness, stridency or listener fatigue. From two to as many as four 15" or 18" (380mm or 457mm)
high-power subwoofers complete the experience with earth-shattering, deep bass.
COMMON VOICING: Synthesis Array uses common voicing across the front three channels. Since identical drivers
are used, each speaker has the same tonal qualities, thus as a sound is panned from one side to the other, there will
be no change in timbre.
MAGNETIC SHIELDING: All front speakers are magnetically shielded, allowing you to place them near video mon-
itors without generating interference or distorting the picture.
DUAL “INSIDE” NEODYMIUM MOTOR STRUCTURE: Two neodymium magnets are used. The “top” neodymium
magnet is magnetized with opposite polarity to the main, lower neodymium magnet. This inverted dual-magnet configu-
ration improves magnetic shielding and offers increased acoustic output.
DEEP-ANODIZED CONE AND DOME MATERIAL: The special deep-anodized aluminum cone and dome material,
together with the motor features, helps to reduce midband distortions to very low levels (approximately 50dB to 60dB
below the fundamental signal driven at 100dB output).
TWO-STAGE PHASE PLUG: The phase plug is a key element in this compression driver. The accuracy of the phase
plug geometry is most important to achieve a wide and flat frequency response. The pressure distribution in the phase
plug is manipulated by adjustments to the number and width of the slots and is optimized to achieve a coherent
pressure front across the operating range at the exit of the phase plug.
SYMMETRICAL INDUCTANCE MODULATION (SIM): The flux-stabilizing ring and copper gap ring are also
optimized for size and position, to help minimize or eliminate “asymmetrical inductance modulation.” Minimizing this
asymmetrical inductance modulation leads to even further distortion reduction and improved vocal clarity.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INCLUDED
SAM1HF
(2) mounting brackets: metal brackets for mounting to the SAM2LF module
(4) knobs: used to securely hold the mounting brackets to the cabinet
SAM2LF
(2) mounting brackets: metal brackets for mounting to the SAM1HF module
(4) knobs: used to securely hold the mounting brackets to the cabinet
SPEAKER PLACEMENT
Positioning your loudspeakers properly is critical in order to achieve the
sonic performance of a home theater. Please read the following section
for guidance in correct and optimal placement.
L
C
R
LEFT AND RIGHT SPEAKERS: If you have purchased a Synthesis Array
Module digital home theater system, then one of the configurations of the
SAM1HF/SAM2LF modules will serve as your front left and right main
speakers. Please see the Configuration and Connection diagrams in the
“SAM1HF and SAM2LF Configuration and Assembly” section to
correctly configure your main speakers.
VIEWING
POSITION
Since the left and right speakers have been designed for maximum local-
ization of sound, they should be placed with the center of the speakers at
about the same height on screen as the actors would be, to aid in the illu-
sion that the actors’ voices are coming directly from their on-screen images.
Ideally, the speakers will be placed about 45 degrees apart from each other,
viewed from the listening position, so that the distance between the speakers
is the same as each speaker’s distance from the listener (see Figure 1).
FLOOR PLAN
Figure 1. 5.1-Channel system
CENTER CHANNEL SPEAKERS: Please see the Configuration and
Connection diagrams in the “SAM1HF and SAM2LF Configuration and
Assembly” section to correctly configure your center speaker. Regardless
of the configuration you have chosen, it is important to place the horn
array vertically during installation in order to take advantage of its sound-
dispersion characteristics. If you mount it horizontally, it will not provide the
correct dispersion pattern. If the speaker is being used with a perforated
projection screen, it should be mounted behind the center of the screen
(see Figure 2).
Figure 2.
If a nonperforated projection screen, plasma display or other fixed video
device is being used in the installation, then the recommended location is
directly below (and as close as possible to) the video display (see Figure 3),
although the inverse of this method will work also.
Figure 3.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER PLACEMENT
NOTE: It is extremely important to place the tweeter/mid-bass arrays for each of the center, left and right speakers
at the same height. The horn array containing the tweeter in the center channel speaker should be no more than two
feet (0.6 meter) higher or lower than those in the left and right speakers. This preserves the “localization integrity” of
“sound pans,” in which the sound appears to move from left to center to right. If the program material also appears to
travel up and down, it can destroy the illusion of panning effects and so should be avoided.
AMBIENT SURROUND SPEAKERS: Although it has been common for many years to use a number of surround
speakers in commercial movie houses, until recently, the traditional home theater configuration called for 5.1
channels, i.e., front left, center, front right, surround left and surround right, plus a low-frequency effects channel.
The newer surround formats that are appearing in consumer audio equipment are calling for more complicated 6.1-
and 7.1-channel systems. The advantages of using additional speakers are many. Additional channels enable a more
versatile use of directionality for a more accurate surround presentation. Also, a higher overall sound-pressure level
can be achieved with less energy expenditure from any individual speaker. Placement of the surround speakers
remains critical.
5.1-CHANNEL SYSTEMS
The ambient surround speakers work optimally if they are placed as far back from
the screen as the viewing chairs are. If there are two rows of chairs, these speakers
should be placed between them.
The ambient surround speakers should be placed higher than the seating area, at
least two feet (0.6 meter) above (seated) ear level (see Figure 4).
The preferred method to mount the ambient surrounds is to put them directly in the
side walls. This lets each speaker radiate to the front and back of the room and to
reflect off the side walls.
There are a few instances in which the ambient surrounds would perform
better if mounted in the ceiling rather than the walls. If one or both of the walls
are “acoustically dead,”due to the presence of windows, fabric, furniture or other
absorption, it may be necessary to turn the ambient speakers sideways and,
instead of mounting them in a vertical orientation, mount them in the ceiling in
a horizontal orientation.
Figure 4.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER PLACEMENT
6.1-CHANNEL SYSTEMS
L
C
R
A 6.1-channel system can be thought of as a 5.1-channel system with the
addition of a rear center speaker placed midway between the two surround
speakers, and further to the rear than the surrounds. It should be placed at the
same height as the side surround speakers (see Figure 5).
7.1-CHANNEL SYSTEMS
In a 7.1-channel system, two speakers are added for rear fill, in addition to the
surround speakers in a 5.1-channel system. The two additional speakers are
placed on the rear wall or near the rear wall in the ceiling (see Figure 6).
FLOOR PLAN
Figure 5. 6.1-Channel system
L
C
R
SIDE
LEFT
SIDE
RIGHT
REAR RIGHT
REAR LEFT
Figure 6. 7.1-Channel system
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAM1HF AND SAM2LF CONFIGURATION AND ASSEMBLY
The different configurations of speaker arrays are accomplished by combining one (1) SAM1HF module with at least
one (1) and up to four (4) SAM2LF modules. The configuration of your system depends greatly on room size and at
what SPL the system will be used. The different array configurations can be used to customize individual speakers
for any application in any system. Typical uses would be as front left, front right and center channel speakers, but
they can also be used as direct radiating surround speakers. A basic speaker array will consist of one (1) SAM1HF
and one (1) SAM2LF as a three-way bi-amped speaker with an active crossover located in the Synthesis Digital EQ
or as a three-way passive speaker when used with the SAM12x crossover.
NOTE: The SAM1HF is the high-frequency horn module, and the SAM2LF is the low-frequency woofer
module; you must use at least one of each for a complete speaker system.
The modules are physically connected to each other by using the included connecting bars and hand-tightened knobs
to mount the modules together. There are multiple mounting points, and several bars should be used to maintain a
rigid connection. Be careful while constructing the module array, as it may become unsteady and tip over.
Make sure the completed speakers are securely mounted and will not fall over, as they may be very heavy
and could cause serious damage if not properly handled.
Any module can be connected to any other module. We have identified four recommended and supported config-
urations. For all configurations, you should observe the following mounting guidelines:
FOR VERTICAL MOUNTING:
1. When mounting the SAM1HF to the SAM2LF with the SAM1HF on top, be sure to keep the modules from
separating while you tighten the bars. This can be accomplished simply by keeping downward pressure on the
front of the module while tightening the screws from the rear.
2. Use at least two mounting bars, running from the top to the bottom of the modules.
3. Use at least four hand screws, two on each module, with four on each module preferred.
FOR HORIZONTAL MOUNTING:
1. When mounting the SAM1HF to the SAM2LF, it is important to keep the top of the modules aligned. This is
accomplished by turning the modules upside down before you begin mounting them together. Once you have
finished, be sure to turn them right side up.
2. Use at least two mounting bars, running from the top to the bottom of the modules.
3. Use at least four hand screws, two on each module, with four on each module preferred.
4. The bars will not extend beyond two modules. If you are connecting three across (as in a dual-woofer module
design), use two sets of bars, each connected to the center module.
FOR A COMBINATION OF HORIZONTAL AND VERTICAL MOUNTING:
1. Attach the vertical modules first.
2. Attach the horizontal modules second.
3. Overlap the mounting bars so that they form a stiff construction.
TRIM PANEL (BAFFLE BLOCKS) INSTALLATION:
1. Purchase the correct trim panels for your configuration.
2. The trim panels will act as both the cosmetic and structural finish of the speaker.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAM1HF AND SAM2LF CONFIGURATION AND ASSEMBLY
IMPORTANT NOTE: Do not place the SAM1HF on its side. It must be mounted with the UHF DRIVER on the
top, as shown below. Failure to do this will have a negative impact on the performance of this speaker.
Detailed Configurations and System Connection
Configuration 1: One SAM1HF and one SAM2LF vertical
Configuration 2: One SAM1HF and one SAM2LF horizontal
NOTE: Shown without the trim panel (baffle blocks) installed on the SAM1HF.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAM1HF AND SAM2LF CONFIGURATION AND ASSEMBLY
Configuration 3: One SAM1HF and two SAM2LF horizontal
NOTE: Shown without the trim panel (baffle blocks) installed on the SAM1HF.
Configuration 4: One SAM1HF and two SAM2LF vertical
NOTE: Shown without the trim panel (baffle blocks) installed on the SAM1HF.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM
To connect the Synthesis Array loudspeakers to the power amplifiers or receiver, use two-conductor insulated speaker
wire. We recommend #14 AWG wire as a minimum size. Your JBL dealer can recommend suitable cables. Both the
SAM1HF and SAM2LF utilize push-style friction binding posts that can accommodate up to #10 AWG stranded wire.
PREPARING THE HOOKUP WIRE
1. First determine the distance between your amplifier and the most distant speaker in each group (fronts, surrounds,
back surrounds, subwoofers).
2. Now make the hookup wires for all speakers in each group this length, even if one speaker is much closer to your
amplifier than the other. This will help maintain proper signal balance.
3. Strip off 3/8" (10mm) of insulation from both ends of each conductor.
4. Twist each set of standard wires into a tightly bunched spiral.
5. Speakers and electronics terminals have corresponding (+) and (–) terminals. Most manufacturers of speakers and
electronics, including JBL, use red to denote the (+) terminal and black for the (–) terminal, although some elec-
tronics manufacturers have adopted the new color-coding standard promulgated by the Consumer Electronics
Association. In that case, the positive terminal will be colored to correspond to the channel position, while the
negative terminal will be black.
It is important to connect all speakers identically: (+) on the speaker to (+) on the amplifier and (–) on the speaker to
(–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and poor imaging.
With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the
correct polarity remains equally important to preserve the proper ambience and directionality of the program material.
Now find a visual difference between the two conductors of each molded pair of speaker wires. Differentiating
marks can be a different color wire (copper or silver); a strand of yarn in one conductor; thin, raised ribs on one part
of the outer insulation; or a printed marking on one part of the outer insulation. It doesn’t matter which of the two
strands go to the (+) and (–) on the speakers and amplifiers, as long as all speakers are connected identically. Push
down on the binding post, insert the wire into the hole, and release.
CONNECTIONS TO THE SYNTHESIS ELECTRONICS
The SAM1HF and SAM2LF speaker modules do not have a built-in crossover. They must be used with the active
crossover as designed in the SDEC-4000 digital equalizer in a bi-amplified configuration or with the outboard passive
crossover, SAM12x, with the SDEC-3000. Each SAM module will require a single amplifier channel in a bi-amplifed
system. Connect the SAM modules according to the chart on the following page.
NOTES:
• The SAM1HF will connect to the HI output of the SDEC-4000 or SAM12x.
• The SAM2LF will connect to the LOW output of the SDEC-4000 or SAM12x.
• Please consult the SDEC-4000 and SDEC-3000 installation guide for detailed instructions.
• DO NOT use a full-range output from an amplifier, as damage may occur unless you are using the SAM12x.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM
INPUT/OUTPUT ASSIGNMENTS WITH ACTIVE CROSSOVER (BI-AMPED)
Surround Processor to SDEC-4000P Inputs
SDEC-4000P Outputs to Amplifiers
S4000IC
S4000IC
Number
Channel
SDEC-4000P
Number
21
22
23
24
Channel
SDEC-4000P
1
FRONT LEFT
A1
SUBWOOFER 1
SUBWOOFER 2
SUBWOOFER 3
SUBWOOFER 4
D1
D2
D3
D4
2
3
4
5
6
7
8
FRONT RIGHT
CENTER
LEFT SIDE
RIGHT SIDE
LEFT REAR
RIGHT REAR
SUBWOOFER
N/C
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
NOTE: You must also connect
®
both the CobraNet audio con-
nections and Ethernet control
connections to complete the
installation. See the SDEC-4000
installation guide for detailed
instructions.
N/C
N/C
N/C
SDEC-4000X Outputs to Amplifiers
S4000IC
Number
9
10
11
12
13
14
15
16
Channel
LEFT FRONT-LOW
LEFT FRONT-HI
RIGHT FRONT-LOW
RIGHT FRONT-HI
CENTER FRONT-LOW
CENTER FRONT-HI
LEFT SIDE 1
LEFT SIDE 2
N/C
SDEC-4000X
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
D1
D2
D3
D4
N/C
17
18
RIGHT SIDE 1
RIGHT SIDE 2
N/C
N/C
19
20
LEFT REAR
RIGHT REAR
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM
SDEC-4000 With Bi-Amplified Speakers (Active Crossover)
SDP-40
INPUTS
COMPONENT VIDEO
MAIN OUTPUTS
RECORD OUTPUTS
1
2
3
3
4
4
5
5
INPUT
1
INPUT
INPUT
2
4
INPUT
3
Y
PR
PB
Y
PR
PR
PB
Y
PR
PB
NOTE: Although the SDP-40
is shown here, connections
for the SDP-5 are similar.
2
1
2
1
(OSD)
OUTPUT
PR PB
Y
PB
Y
VIDEO
VIDEO
1
2
6
7
8
Fix
FRONT
CENTER
SIDE
Fix
Var
Var
SUBWOOFER
REAR
ZONE
2
AUX
(L)
(R)
(LS)
(RS)
(C)
L
L
L
L
L
L
(SUB)
R
R
R
R
R
R
LFE
MICROPHONE INPUTS
AUDIO
TRIGGER OUTPUTS
MAIN AUDIO OUTPUTS
AUDIO
S/PDIF
1
2
5
3
1
2
3
4
1
4
2
5
3
1
2
4
6
IR IN
6
RS 232
FRONT
CENTER
LFE
L
SUBWOOFER
R
ZONE
2
L
R
L
R
L
AUX
R
L
R
L
SIDE
R
REAR
To Ethernet hub
(for system calibration)
SDEC-4000P
SDEC-4000X
To Ethernet hub
(for system calibration)
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
S5160 POWER AMPLIFIER
IN
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
~
50/60Hz
1800W
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
S5160
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
S5160 POWER AMPLIFIER
IN
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
~
50/60Hz
1800W
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
S5160
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
IN
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
TRIGGERS
IN
S800 POWER AMPLIFIER
S800 POWER AMPLIFIER
NORTHRIDGE, CA
NORTHRIDGE, CA
BRIDGED
BRIDGED
Ch.
1
Ch.
Input
2
Ch.
1
Ch.
Input
2
WARNING; To reduce the risk of fire or
electric shock, do not expose
WARNING; To reduce the risk of fire or
electric shock, do not expose
BRIDGED
Input
BRIDGED
Input
MONO
STEREO
MONO
STEREO
this appliance to rain or moisture
this appliance to rain or moisture
OUT
OUT
No user serviceable parts inside. Refer
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
MANUAL
ON
servicing to qualified personnel.
AUTO
MANUAL
ON
ON
ON
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
ON
10A
120V
50/60Hz
1200W
~
120V
~
50/60Hz
1200W
OFF
OFF
WARNING:
serial number
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
,
HAZARDOUS ENERGY
,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
BRIDGED
WARNING:
serial number
+
+
BRIDGED
-
+
+
-
+
-
-
+
-
-
Ch.
1
Output
Ch.
2
Output
Ch.
1
Output
Ch.
2
Output
S800
S800
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE SPEAKER TO THE REST OF YOUR SYSTEM
INPUT/OUTPUT ASSIGNMENTS WITH PASSIVE CROSSOVER
The SDEC-3000 supports up to 7.1 input with up to 7.1 output. The input and output assignments are as described
in the below chart. You must make the correct connections from the surround processor output to the amplifier input
for the system to work correctly. Please refer to the connection diagram for more information.
The correct Synthesis Interconnect kit includes all the necessary connections for using the SDEC in the Synthesis sys-
tem. Please be sure to order the S3000IC for use with SDEC-3000 and S4000IC for use with SDEC-4000. Retrofit kits are
also available. Please contact JBL Synthesis Technical Support for more information at (888) 691-4171 (USA only).
CONNECTION NOTES
• Please follow the wiring diagram and the Input/Output Assignments chart for correct connections.
• You will need to use the Ethernet network port on the rear panel of the unit for the final calibration process.
You can use a crossover network cable if you plan to connect directly to the SDEC-3000 from a computer.
Alternatively, you can connect the SDEC-3000 through any standard Ethernet hub.
• When using the SDP-40 processor, make sure the subwoofer (in speaker setup) is set to Mono output and connect
to the Subwoofer Left output. Do not use the LFE output.
NOTE: Place the SAM12x
passive crossover as close
to the speakers as possible.
The SAM12x has a single
speaker level input and multiple
outputs for the SAM1HF and
SAM2LF speaker modules.
Surround Processor to SDEC-3000 Inputs
S3000IC
Number
Channel
LEFT FRONT
RIGHT FRONT
CENTER FRONT
LEFT SIDE
SDEC-3000
1
2
3
4
5
6
7
8
A1
A2
A3
A4
B1
B2
B3
B4
RIGHT SIDE
LEFT REAR
RIGHT REAR
SUBWOOFER
(Mono Sub Left)
SDEC-3000 Outputs to Amplifiers
S3000IC
Number
9
10
11
12
Channel
LEFT FRONT
RIGHT FRONT
CENTER FRONT
LEFT SIDE
SDEC-3000
C1
C2
C3
C4
D1
D2
D3
D4
13
14
RIGHT SIDE
LEFT REAR
15
16
RIGHT REAR
SUBWOOFER
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION TO THE REST OF THE JBL SYNTHESIS SYSTEM
SDEC-3000 With Passive Crossover (SAM12x)
SDP-5
SDP-5 Digital Surround Processor/Controller
INPUTS
MAIN
ZONE
2
JBL, Inc. Northridge, CA
Assembled in USA
S/PDIF INPUTS
2
1
3
2
4
TUV
NOTE: Although the
SDP-5 is shown here,
connections for the
SDP-40 are similar.
INPUT
1
INPUT
2
Y
Y
PR
PR
PB
PB
Y
Y
PR
PR
PB
PB
C
US
1
3
1
1
2
2
3
4
4
5
5
VIDEO
VIDEO
AUDIO
CAUTION
S/N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC
ELECTRIQUE
4
NE PAS OUVRIR
OUTPUT
CENTER
INPUT
7
3
IR IN
3
6
8
FRONT
SIDE
REAR
TRIGGER
OUTPUTS
(L)
(R)
(L)
(R)
(C)
(LS)
(RS)
(C)
(LS)
(RS)
L
L
L
S/PDIF
OUT
1
2
RS-232
(SUB)
(SUB)
R
R
R
SUBWOOFER
OUTPUTS
1
2
AC 100-240V ~ 50-60 HZ, 60W
SDEC-3000
To Ethernet hub
(for system calibration)
S7150
NO USER SERVICEABLE PARTS INSIDE. REFER
JBL SYNTHESIS
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
SERVICING TO QUALIFIED PERSONNEL
NORTHRIDGE, CA
Ch. 1
Input
Ch. 2
Input
Ch. 3
Input
Ch. 4
Input
Ch. 5
Input
Ch. 6
Input
Ch. 7
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
~
50/60Hz
1800W
OFF
WARNING:
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
SAM12x
LEFT
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
FRONT
+
+
+
+
+
+
+
-
-
-
-
-
-
-
serial number
Ch. 1 Output
Ch. 2 Output
Ch. 3 Output
Ch. 4 Output
Ch. 5 Output
Ch. 6 Output
Ch. 7 Output
SAM12x
RIGHT
S800
VOIR LE CAHIER D'
INSTRUCTION
ATTENTION:
JBL SYNTHESIS
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
FRONT
S800 POWER AMPLIFIER
IN
NORTHRIDGE, CA
BRIDGED
Ch. 1
BRIDGED
Input
Ch. 2
Input
WARNING; To reduce the risk of fire or
electric shock, do not expose
MONO
STEREO
this appliance to rain or moisture
SAM12x
CENTER
FRONT
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
MANUAL
ON
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V
~
50/60Hz
1200W
OFF
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING:
serial number
BRIDGED
+
+
-
+
-
-
Ch. 1 Output
Ch. 2 Output
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SYMPTOM
PROBABLE CAUSE
SOLUTION
No sound coming
from speaker
• Amplifier not turned on
•Turn on amplifier.
• Amplifier gain is low
•Make sure that there is
amplifier gain for that channel.
• Correct source not
selected or turned on
•Select proper source.
• Defective patch cords to amplifier
•Check/replace patch cords.
• Speaker wires not
•Check speaker wire
connected to amplifier
connection to amplifier.
• Balance control set improperly
•Make sure Balance control is set
at center, or 12 o’clock, position.
• Speaker wires damaged
or shorted
•Make sure none of the speaker wires
are frayed, cut or punctured. Make sure
no wires are touching other wires or
terminals and creating a short circuit.
®
®
• Speaker not configured
correctly
•In Dolby Digital or DTS mode, make
sure that the receiver/processor is
configured so that the speaker in
question is enabled.
®
• Center speaker is configured
incorrectly
•In Dolby Pro Logic mode, make sure the
center speaker is not in phantom mode.
• Problem not diagnosed
•To diagnose the likely source of the
problem, it is often helpful to switch the
nonfunctioning speaker with one that
is functioning correctly. Turn off all
electronics before exchanging the
speakers. Turn everything back on, and
determine whether the problem is in
the same place, or has moved with the
speaker. If the problem is in the same
place, the source is most likely with your
receiver or amplifier. If the problem has
followed the speaker, then contact your
authorized JBL Synthesis custom installer
or dealer for further assistance. If that
is not possible, visit our Web site at
Bass is very weak
• Subwoofers are wired out
of phase
•Make sure that positive terminals on the
subwoofers go to the positive terminals
on the amplifiers (red) and do the same
for the negatives.
• Subwoofers have not
been placed optimally
•Experiment with different locations.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SAM1HF
SAM2LF
N/A
ULTRAHIGH-FREQUENCY DRIVER
HIGH-FREQUENCY TRANSDUCER
045TI 1" (25MM) PURE-TITANIUM COMPRESSION DRIVER
WITH ALUMINUM EDGE-WOUND VOICE COIL AND
2" (51MM) NEODYMIUM MOTOR ASSEMBLY, MOUNTED
IN A SONOGLASS® CONSTANT-DIRECTIVITY HORN
435AL-1 3" (75MM) AQUAPLAS-TREATED ALUMINUM-DOME N/A
COMPRESSION DRIVER WITH ALUMINUM EDGE-WOUND
VOICE COIL AND NEODYMIUM MOTOR ASSEMBLY,
MOUNTED IN A VERTICAL SONOGLASS® CONSTANT-
DIRECTIVITY HORN
LOW-FREQUENCY TRANSDUCER
N/A
8" (200MM) DEEP-ANODIZED ALUMINUM
CONE AND DOME MATERIAL WITH DUAL
“INSIDE” NEODYMIUM MAGNETS, SHIELDED
MOTOR STRUCTURE AND 2" (51MM)
VOICE COILS
SENSITIVITY (2.83V/1M)
98DB
92DB
FREQUENCY RESPONSE (–3DB)
36HZ TO 40KHZ*
36HZ TO 40KHZ*
300 WATTS
N/A
MAX. RECOMMENDED AMPLIFIER POWER 300 WATTS
CROSSOVER FREQUENCIES
NOMINAL IMPEDANCE
9KHZ
6 OHMS
6 OHMS
DIMENSIONS (H X W X D)
17-1/4" X 8" X 11-1/2" **
(438MM X 200MM X 292MM)
20" X 10" X 10-3/4" **
(508MM X 254MM X 273MM)
WEIGHT PER SPEAKER
25 LB (11KG)
29 LB (13KG)
* Note 1: Frequency response is for the complete speaker module, SAM1HF/SAM2LF together.
** Note 2: Dimensions do not include mounting hardware or feet.
Add 3" (75mm) depth for mounting hardware, and 1" (25mm) height for feet.
Features, specifications and appearance are subject to change without notice.
JBL, JBL Synthesis, Synthesis and SonoGlass are trademarks of Harman International Industries, Incorporated, registered in the United States
and/or other countries. Array, Symmetrical Field Geometry and Vented Gap Cooling are trademarks of Harman International Industries, Incorporated.
CobraNet is a registered trademark of Peak Audio, a division of Cirrus Logic, Inc.
THX is a registered trademark, and THX Ultra2 is a trademark, of THX Ltd. All rights reserved.
SACD is a trademark of Sony Corporation.
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.
DTS is a registered trademark of DTS, Inc.
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the products described
in this owner’s manual are in compliance with technical
standards:
EN 61000-6-3:2001
Harman Consumer Group, Inc.
250 Crossways Park Drive, Woodbury, NY 11797
EN 61000-6-1:2001
8500 Balboa Boulevard, Northridge, CA 91329
818.830.8757
Luc Guillaume
Harman Consumer Group, Inc.
Château du Loir, France 4/07
Part No. 361697-001 4/07
Download from Www.Somanuals.com. All Manuals Search And Download.
|