®
N O R T H R ID G E ™ E S E R IE S
E1 0 , E2 0 , EC 2 5
O W N E R ’S G U ID E
Download from Www.Somanuals.com. All Manuals Search And Download.
W A LL- M O U N T IN G (M o d e l E10 Only)
NOTICE: Im p o rtant S afe ty
No te s
back of the enclosure in the
two bottom corners so that
the cabinet is spaced evenly
from the wall. Select a suit-
able mounting location on a
wall. (The ceiling is not a suit-
able mounting location.)
anchor, and tighten them until
the back of each screw head
is about 1/8 inch (3mm) from
the wall. See Figure 2. Install
the loudspeaker by slowly
moving the cabinet toward
the screws so that the screw
heads clear the larger circu-
lar portion of the two key-
holes. Once both screw
• Proper selection of mount-
ing hardware and installation
of the wall brackets are the
responsibility of the customer.
• This product is not intended
for ceiling mounting.
Drill two pilot holes, appropri-
ately sized for the specific
self-tapping screw or wall
anchor that you will be using.
The holes should be 8 inches
(203mm) apart. See Figure 1.
The holes should be 3/4"
(19mm) below where you
want the top of the enclosure
to be positioned. Use a car-
penter’s level to ensure that
the holes are even and that
the speaker will mount on the
level.
Two Number 8 round head or
pan head screws should be
used per loudspeaker. The
screw head should be
between 5/16 inch (8mm) and
1/4 inch (6.3mm) in diameter,
and the screw should be at
least 2 inches (50mm) in
length.
heads have entered the key-
holes, the loudspeaker should
gently be lowered onto the
screw shafts. Check that the
loudspeaker is firmly locked
onto the screws by gently
pulling the speaker down and
forward.
When installing screws in any
wall, always use properly
selected wall anchors. Attach
two of the four self-adhesive
rubber pads that came with
the E10 loudspeaker to the
8" (203mm)
1/8"
Install the two screws into
either a wooden wall stud or
(3mm)
T R O U B LE S H O O T IN G
If the re is no s o und fro m
any o f the s p e ake rs :
lem is in the same channel,
use with digital “.1” surround
formats.
If the re is no s o und fro m
the s urro und s p e ake rs :
the source of the problem is
most likely with your receiver
or amplifier, and you should
consult the owner’s manual for
that product for further infor-
mation. If the problem has fol-
lowed the speaker, consult
your dealer for further assis-
tance or, if that is not possi-
further information.
• Check that receiver/ampli-
fier is on and that a source is
playing.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed,
cut or punctured.
• Review proper operation of
your receiver/amplifier.
If the re is no s o und c o m ing
fro m o ne s p e ake r:
• Check the “Balance” control
on your receiver/amplifier.
• Review proper operation of
your receiver/amplifier and its
surround sound features.
If the s ys te m p lays at lo w
vo lum e s b ut s huts o ff as
vo lum e is inc re as e d :
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers. Make sure
no wires are touching other
wires or terminals and creat-
ing a short circuit.
• Make sure the movie or TV
show you are watching is
recorded in a surround sound
mode. If it is not, check to see
whether your receiver/ampli-
fier has other surround modes
you may use.
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• In Dolby* Digital or DTS®
mode, make sure that the
receiver/processor is config-
ured so that the speaker in
question is enabled.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
•
In Dolby Digital or DTS mode,
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
make sure your receiver/pro-
cessor is configured so that
the surround speakers are
enabled.
• Review the operation of your
DVD player and the jacket of
your DVD to make sure that
the DVD features the desired
Dolby Digital or DTS mode,
and that you have properly
selected that mode using both
the DVD player’s menu and
the DVD disc’s menu.
If the re is no (o r lo w ) b as s
o utp ut:
• Turn off all electronics
and switch the speaker in
question with one of the other
speakers that is working cor-
rectly. Turn everything back
on, and determine whether
the problem has followed the
speakers, or has remained in
the same channel. If the prob-
• Make sure the polarities
(+ and –) of the left and right
“Speaker Inputs” are con-
nected properly.
• Consider adding a powered
subwoofer to your system for
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C IF IC A T IO N S
E10
E2 0
EC2 5
Description
Description
2-Way 5" bookshelf
Description
2-Way 4" wall-mount/bookshelf
2-Way dual 5" center
Maximum Recommended
Amplifier Power**
Maximum Recommended
Amplifier Power**
Maximum Recommended
Amplifier Power**
100W
125W
150W
Power Handling
(Continuous/Peak)
Power Handling
(Continuous/Peak)
Power Handling
(Continuous/Peak)
50W/200W
60W/240W
75W/300W
Nominal Impedance
8 Ohms
Nominal Impedance
8 Ohms
Nominal Impedance
8 Ohms
Sensitivity (2.83V/1m)
86dB
Sensitivity (2.83V/1m)
86dB
Sensitivity (2.83V/1m)
90dB
Frequency Response (–3dB)
75Hz – 20kHz
Frequency Response (–3dB)
68Hz – 20kHz
Frequency Response (–3dB)
80Hz – 20kHz
Crossover Frequency
2000Hz
Crossover Frequency
3000Hz
Crossover Frequency
4000Hz
High-Frequency Transducer
High-Frequency Transducer
High-Frequency Transducer
3/4" (19mm) Titanium-laminate
dome, shielded
3/4" (19mm) Titanium-laminate
dome
3/4" (19mm) Titanium-laminate
dome, shielded
Low-Frequency Transducer
4" (100mm) PolyPlas,™ shielded
Baffle
Low-Frequency Transducer
5" (130mm) PolyPlas,™ shielded
Baffle
Low-Frequency Transducer
Dual 5" (130mm) PolyPlas,™ shielded
Baffle
Low diffraction, IsoPower™
Port
Low diffraction, IsoPower™
Port
Low diffraction, IsoPower™
Port
FreeFlow™ flared
FreeFlow™ flared
FreeFlow™ flared
Network
Network
Network
Straight-Line Signal Path™ (SSP)
Terminals
Straight-Line Signal Path™ (SSP)
Terminals
Straight-Line Signal Path™ (SSP)
Terminals
Gold-plated, 5-way binding posts
Dimensions (H x W x D)
Gold-plated, 5-way binding posts
Dimensions (H x W x D)
Gold-plated, 5-way binding posts
Dimensions (H x W x D)
10" x 10-1/8" x 5-1/4"
254mm x 257mm x 133mm
10-7/8" x 6" x 8-1/8"
275mm x 153mm x 206mm
6-7/8" x 18" x 10"
175mm x 457mm x 254mm
Weight Per Speaker
8 lb/3.6kg
Weight Per Speaker
7 lb/3.2kg
Weight Per Speaker
15.6 lb/7.1kg
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility, that the products described
in this owner’s manual are in compliance with technical
standards:
EN 50081-1:1992
EN 50082-1:1997
Gary Mardell
Harman Consumer
International
Chateau-du-Loir, France 2/03
P R O S O U N D C O M ES H O M E ™
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797
8500 Balboa Boulevard, Northridge, CA 91329
*Trademark of Dolby Laboratories.
DTS is a registered trademark of Digital Theater Systems, Inc.
2, route de Tours, 72500 Chateau-du-Loir, France
** The maximum recommended amplifier power rating will ensure
proper system headroom to allow for occasional peaks. We do not
recommend sustained operation at these maximum power levels.
© 2003 Harman International Industries, Incorporated
JBL is a registered trademark of Harman International Industries, Incorporated.
Part No.406-000-01530
All features and specifications are subject to change without notice.
All dimensions include grilles.
Download from Www.Somanuals.com. All Manuals Search And Download.
|