JBL Portable Speaker P 432 User Manual

Au t om ot iv e L ou d s p e a k e r s  
P -432, P -532, P -632, P -9632, P -9633,  
P -332, P -6432, P -7532, P -23t & P -K it Ow n e r ’s M a n u a l  
G E N U I N E J B L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation of the P-332, P-6432 and P-7532, as shown in Figure 1.  
Installation of the P-432, P-532, P-9632 and P-9633, as shown in Figures 2 and 3.  
Figure 1.  
Figure 2.  
Figure 3.  
Note: The P-332, P-6432 and P-7532 are designed as  
direct replacem ents for original-equipm ent speakers  
m ounted behind factory grilles.  
Note: If you are m ounting the P-532, P-9632 or P-9633  
behind factory grilles, om it the grille and grille tray in  
Figure 2.  
Note: Som e installations m ay require som e or all  
of the m ounting ears to be rem oved from the P-432.  
Rem ove your original speakers first to determ ine  
whether any m ounting ears m ust be rem oved.  
0 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation of the P-632, as shown in Figures 4a and 4b. The P-632 uses J BL's Interm ount III™  
m ounting system . Interm ount III™ provides for easy installation of these speakers in m any standard  
and nonstandard locations that will accom m odate a 6-1/2" speaker.  
Figure 4a.  
Figure 4b.  
Using Interm ount III™ in Am erican and J apanese cars with  
openings for 6-1/2" speakers.  
Using Interm ount III™ in European and Am erican 165m m  
openings or custom -m ounting the speaker.  
Im portant: When using the steel m ounting rings, you  
m ust m ake sure that the rings are m ounted to a  
com pletely at surface.  
0 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Converting the P-432, P-532 and P-632 to a com ponent system using the optional P-Kit  
(sold separately), as shown on pages 5 and 6.  
Separating the tw eeter and w oofer, as shown in Figures 5a and 5b.  
Figure 5a.  
Figure 5b.  
Rem ove the orange wire cover by inserting a sm all  
Detach the tweeter by turning it counterclockwise to  
unlock it, then pull it away from the woofer while feeding  
the wires through the pole piece.  
Install the woofer phase plug and turn it clockwise to lock  
it in place.  
screwdriver into the notch between the two term inals and  
prying upwards. Disconnect the tweeter wires from the  
term inal. Reinstall the cover after rem oving the tweeter.  
0 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the tw eeter (P-23t), as shown in Figures 6a  
and 6b. The tweeter m ay be either surface-m ounted or  
flush-m ounted with parts supplied in the P-Kit.  
Connecting the w oofer and tw eeter to the  
passive crossover, as shown in Figures 7a and 7b.  
Figure 7a.  
Figure 6a.  
7b.  
Position the "Lo Pass" and "Twt Frq" according to the  
speaker you are using as shown in the callouts in Figure 7b.  
Surface-m ounting the P-23t.  
J um per Functions  
Lo Pass (Low Pass): You m ay engage or disengage the  
woofer low-pass filter with this jum per. Because the  
natural rolloff of the P-532 and the P-632 begin at a lower  
frequency than that of the P-432, this jum per should only  
be in the "on" position when the P-432 is being used.  
Figure 6b.  
Twt Lvl (Tweeter Level): You m ay attenuate the level of  
the tweeter's output using this jum per.  
Twt Frq (Tweeter Frequency): Because the P-432 has  
usable frequency response higher than that of the P-532  
or P-632, th e optimum crossover frequen cy for the tweeter  
is slightly higher when the P-23t is used with the 4" woofer.  
Note: For the m ost accurate sound reproduction,  
the jum per positions should be set according to J BL  
recom m endations. If an alternate setting better suits  
your preference or works better for your particular  
installation, you m ay position the jum pers as you like  
without affecting your warranty.  
Rem ove the top of the passive crossover by squeezing  
the sides and lifting off the top. Mount the crossover  
with screws or wire ties through the m ounting holes.  
Connect the wires between the crossover, and between  
the woofer and tweeter as shown.  
Note: You m ay upgrade the perform ance of the P-432,  
P-532 or P-632 (when it is used as a m ultielem ent speak-  
er) by utilizing the passive crossover contained in the  
P-Kit and leaving the tweeter m ounted on the woofer.  
Flush-m ounting the P-23t (use a hole saw to cut a 1-9/16"  
hole in the m ounting surface).  
0 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
P -432  
P -532  
P -632  
P -9632  
P -9633  
4" 2-Way or  
5-1/4" 2-Way or  
6-1/2" 2-Way or  
6" x 9" 2-Way  
6" x 9" 3-Way  
Com ponent System  
Com ponent System  
Com ponent System  
Com ponent System  
Com ponent System  
with Optional P-Kit  
Therm alum™  
NeoGlass™  
with Optional P-Kit  
Therm alum™  
NeoGlass™  
with Optional P-Kit  
Therm alum™  
NeoGlass™  
Woofer-Cone Material  
Therm alum™  
NeoGlass™  
25Hz – 22kHz  
Therm alum™  
NeoGlass™  
25Hz – 22kHz  
Tw eeter-Diaphragm Material  
Frequency Response  
Sensitivity  
65Hz – 22kHz  
55Hz – 22kHz  
45Hz – 22kHz  
90dB  
90dB  
91dB  
92dB  
92dB  
Recom m ended Am plifier  
Pow er Range as Multielem ent  
5W – 120W  
5W – 150W  
5W – 175W  
5W – 250W  
5W – 250W  
Recom m ended Am plifier Pow er  
Range as Com ponent  
5W – 175W  
2" (51m m )  
5W – 200W  
5W – 225W  
N/A  
N/A  
Mounting Depth  
2-1/4" (57m m )  
2-1/2" (64m m )  
3-1/8" (80m m )  
3-1/8" (80m m )  
P -332  
P -6432  
P -7532  
P -23t  
P -Kit  
3-1/2" 2-Way  
Com ponent System  
4" x 6" 2-Way  
Plate  
5" x 7" 2-Way or  
Com ponent System  
Com ponent  
Tweeter  
Conversion Kit  
for P-432, P-532,  
with Optional P-Kit  
Therm alum™  
NeoGlass™  
P-632, P-7532  
Woofer-Cone Material  
Tw eeter-Diaphragm Material  
Frequency Response  
Therm alum™  
NeoGlass™  
70Hz – 22kHz  
Therm alum™  
NeoGlass™  
65Hz – 22kHz  
N/A  
N/A  
N/A  
N/A  
N/A  
NeoGlass™  
5kHz – 22kHz  
45Hz – 22kHz  
Sensitivity  
89dB  
90dB  
91dB  
91dB  
Recom m ended Am plifier  
(with crossover)  
Pow er Range as Multielem ent  
5W – 90W  
5W – 150W  
5W – 175W  
5W – 100W  
N/A  
Recom m ended Am plifier Pow er  
Range as Com ponent  
N/A  
N/A  
N/A  
N/A  
N/A  
Mounting Depth  
1-3/4" (45m m )  
1-7/8" (48m m )  
2-1/4" (58m m )  
7/8" (23m m )  
7/8" (23m m )  
0 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Declaration of Conformity  
We, JBL Europe A/S  
Kongevejen 194B  
DK-3460 Birkerød  
DENMARK  
declare in own responsibility, that the products  
described in this owner’s manual are in compliance  
with technical standards:  
EN 50081-1:1992  
EN 50082-1:1992  
Steen Michaelsen  
JBL Europe A/S  
Birkerød. DENMARK. 3/99  
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797  
800-336-4JBL (4525) www.jbl.com Part No. POWSPKRSOM Made in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

JVC Home Theater System GVT0141 003A User Manual
Kenmore Air Conditioner 580751515 User Manual
Kenwood Car Amplifier KAC PS501F User Manual
Kenwood Marine Radio KCA RC50MR User Manual
Keurig Coffeemaker SS 700 User Manual
KitchenAid Cooktop W10526088A User Manual
KitchenAid Ice Maker KUIS18PNTB0 User Manual
KitchenAid Mixer KSMC50 User Manual
KitchenAid Ventilation Hood KWC380J User Manual
Kramer Electronics TV Cables PT 101H User Manual