®
®
JBL CONTROL
SERIES
®
CONTROL MONITOR
LOUDSPEAKERS
OWNER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL-MOUNTING
WIRING THE SYSTEM
IMPORTANT: MAKE SURE ALL EQUIPMENT IS
TURNED OFF BEFORE MAKING ANY CONNECTIONS.
NOTE: The customer is responsible for proper selection and use of mounting
hardware (available through hardware stores), to properly and safely wall-mount
the module.
For speaker connections, use a high-quality speaker wire with polarity coding.
The side of the wire with a ridge or other coding is usually considered positive
polarity (i.e., +).
Step 1.
Run the speaker wire through the hole in the
center of the bracket, as shown in Figure 4.
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
The speakers have coded terminals
that accept a variety of wire
connectors. The most common
connection is shown in Figure 8.
To ensure proper polarity, connect
each + terminal on the back of the
amplifier or receiver to the respec-
tive +(red) terminal on each speaker,
as shown in Figure 9. Connect the
Figure 4.
Step 2.
–
(black) terminals in a similar way.
Speaker Wire
Attach the bracket to the wall in the desired
location, using the appropriate screws and
anchors, as shown in Figure 5.
See the owner’s guides that were
included with your amplifier, receiver
and television to confirm connection
procedures.
Figure 8. This figure shows how to
connect bare wires to the terminals.
IMPORTANT: DO NOT REVERSE POLARITIES
(I.E., + TO OR TO +) WHEN MAKING CONNECTIONS.
–
–
DOING SO WILL CAUSE POOR IMAGING AND
DIMINISHED BASS RESPONSE.
STANDARD CONNECTION
Figure 5.
Standard
Connection
Step 3.
Using the supplied Allen wrench, remove
the screws and end caps from the top and
bottom of the speaker, as shown in Figure 6.
Figure 9. Wiring diagram shows polarity connections for one channel
of a stereo or home theater system.
FINAL ADJUSTMENTS
Check the speakers for playback, first by setting the system volume control
to a minimum level, and then by applying power to your audio system. Play
a favorite music or video segment and increase the system volume control
to a comfortable level.
Figure 6.
Step 4.
NOTE: You should hear balanced audio reproduction across the entire
frequency spectrum. If not, check all wiring connections or consult the
authorized JBL dealer from whom you purchased the system for more help.
Connect the speaker wire to the speaker, as described in “Wiring the System.”
Step 5.
Slide the speaker into the bracket, aligning
the holes in the bracket with the threaded
inserts in the top and bottom of the speaker,
and reattach the screws and end caps
removed in Step 3, as shown in Figure 7.
The amount of bass you hear and the stereo-image quality will be affected
by a number of different factors, including the room’s size and shape, the
construction materials used to build the room, the listener’s position relative
to the speakers, and the position of the speakers in the room.
Listen to a variety of music selections and note the bass level. If there is too
much bass, move the speakers away from nearby walls. Conversely, if you
place the speakers closer to the walls, there will be more bass output.
CARE OF YOUR SPEAKER SYSTEM
Each enclosure has a finish that does not require any routine maintenance.
When needed, use a soft cloth to remove any fingerprints or dust from the
enclosure or grille.
Figure 7.
Step 6.
NOTE: Do not use any cleaning products or polishes on the cabinet
Hand-tighten securely. You may angle the speaker up to 15 degrees to the
right or the left before final tightening.
or grille.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
®
CONTROL MONITOR
LOUDSPEAKERS
Frequency Response (–3dB)
50Hz – 40kHz
Recommended Amplifier Power Range* 10W – 125W
Power Handling (Peak)
Sensitivity (2.83V/1m)
Nominal Impedance
Crossover Frequency
240W
87dB
8 Ohms
2400Hz – 18dB/octave, low-pass;
2400Hz – 24dB/octave, high-pass
Low-Frequency Transducer
High-Frequency Transducer
5" (130mm) PolyPlas,™ shielded
1" (25mm) Soft-dome,
shielded; EOS waveguide
Dimensions With Grille
(H x W x D)
10" x 6-5/8" x 8"
(259mm x 164mm x 202mm)
Weight per Speaker
6.6 lb (3kg)
The recommended amplifier power range rating will ensure proper system headroom
to allow for occasional peaks. We do not recommend sustained operation at these
maximum power levels.
*
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product
described in this owner’s manual is in compliance
with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
JBL and Control are trademarks of Harman International Industries, Incorporated, registered
in the United States and/or other countries. Elliptical Oblate Spheroidal and PolyPlas are
trademarks of Harman International Industries, Incorporated.
Features, specifications and appearance are subject to change without notice.
Harman Consumer Group, Inc.
250 Crossways Park Drive, Woodbury, NY 11797 USA
© 2008 Harman International Industries, Incorporated. All rights reserved.
Part No. 406-000-05970-E
Laurent Rault
Harman Consumer Group, Inc.
Château du Loir, France 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|