Invacare® Jymni™ Pediatric Series Wheelchair
9000 Standard Weight
9000 Light Weight
9000 Light Weight Recliner
EN
User Manual
This manual MUST be given to the user of the product.
BEFORE using this product, read this manual and save for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Typical Product Parameters ..............................................................................................................................................................................................................10
Component Identification..................................................................................................................................................................................................................12
General Guidelines..............................................................................................................................................................................................................................13
Operating Information........................................................................................................................................................................................................................14
Safety/Handling of Wheelchairs........................................................................................................................................................................................................19
Transferring To and From Other Seats..........................................................................................................................................................................................25
Unfolding and Folding Wheelchair...................................................................................................................................................................................................26
SAFETY INSPECTION/TROUBLESHOOTING .............................................................................................................................28
Safety Inspection Checklist................................................................................................................................................................................................................ 28
Troubleshooting...................................................................................................................................................................................................................................30
Transporting the Invacare Jymni.......................................................................................................................................................................................................33
Installing/Removing the Swingaway Footrest Assembly..............................................................................................................................................................34
Swingaway Footrest Height Adjustment ........................................................................................................................................................................................35
Heel Loop Replacement..................................................................................................................................................................................................................... 36
Installing/Removing Elevating Legrest Assembly...........................................................................................................................................................................37
Adjusting the Elevating Legrest Assembly...................................................................................................................................................................................... 38
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Adjusting Armrest Height..................................................................................................................................................................................................................39
Using Swing-Back Arms......................................................................................................................................................................................................................40
Removing or Replacing Armrest...................................................................................................................................................................................................... 41
Replacing Desk/Full Length Armrest Pad (Fixed Height Arms Only)......................................................................................................................................42
Replacing Clothing Guards (Fixed Height Arms Only)...............................................................................................................................................................42
Converting Between Space Saver and Conventional Arms....................................................................................................................................................... 42
Replacing Seat Upholstery .................................................................................................................................................................................................................44
Adjusting Back Height.........................................................................................................................................................................................................................46
Adjusting Back Angle - Standard/Light Weight Adjustable Angle Back Model Only............................................................................................................47
REAR WHEELS ...................................................................................................................................................................................48
Adjusting the Quick-Release Axle ...................................................................................................................................................................................................50
Replacing Rear Wheel Handrim.......................................................................................................................................................................................................51
Replacing/Repairing Rear Wheel Tire/Tube..................................................................................................................................................................................51
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
10 ANTI-TIPPERS/WHEEL LOCKS ......................................................................................................................................................54
Installing/Adjusting Anti-tippers........................................................................................................................................................................................................54
Using Patient Operated Wheel Locks ............................................................................................................................................................................................57
Adjusting Patient-Operated Wheel Locks.....................................................................................................................................................................................58
11 RECLINER ............................................................................................................................................................................................59
Operating Recliner ..............................................................................................................................................................................................................................59
Installing/Removing Headrest Extension.........................................................................................................................................................................................61
Replacing Headrest Pillow .................................................................................................................................................................................................................61
Replacing Headrest/Back Upholstery..............................................................................................................................................................................................62
Adjusting Headrest/Back Upholstery Tension..............................................................................................................................................................................63
Storing/Replacing Spreader Bar........................................................................................................................................................................................................63
Adjusting the Seat Width and Depth..............................................................................................................................................................................................64
12 OPTIONS .............................................................................................................................................................................................65
Installing Telescoping I.V. Rod/O2 Holders...................................................................................................................................................................................65
Cleaning..................................................................................................................................................................................................................................................66
Installing the 1-inch Forward Rear Wheel Positioner.................................................................................................................................................................67
Installing/Adjusting Stroller Handles................................................................................................................................................................................................ 68
Installing/Removing the Solid Seat Insert........................................................................................................................................................................................69
Installing/Removing the Solid Back Insert.......................................................................................................................................................................................69
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1 GENERAL
1 General
1.1 Symbols
Warnings
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage.
See the information below for definitions of the signal words.
DANGER
ƽ
Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
ƽ
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
ƽ
Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or
both.
IMPORTANT
!
Indicates a hazardous situation that could result in damage to property if it is not avoided.
Gives useful tips, recommendations and information for efficient, trouble-free use.
.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1 GENERAL
1.2 Limited Warranty
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS
MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer. This warranty is
not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner. Coverage under this warranty
will end upon any such subsequent sale or other transfer of title to any other person.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
Invacare warrants the side frames and cross members of this product when purchased new and unused to be free from defects in materials and
workmanship for a period of five (5) years from the date of purchase from Invacare or a dealer, with a copy of the seller’s invoice required for coverage
under this warranty. Invacare warrants the upholstered materials (seat, back and armrests of the arm assembly) and remaining components of this
product when purchased new and unused to be free from defects in materials and workmanship for a period of thirteen (13) months from date of
purchase from Invacare or a dealer, with a copy of the seller’s invoice required for coverage under this warranty. If within such warranty periods any
such product shall be proven to be defective, such product shall be repaired or replaced, at Invacare’s option. This warranty does not include any labor
or shipping charges incurred in replacement part installation or repair of any such product. Invacare’s sole obligation and your exclusive remedy under
this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare product. In the event you do not receive satisfactory warranty
service, please write directly to Invacare at the address at the bottom of this page. Provide dealer’s name, address, the product model number, date of
purchase, indicate nature of the defect and, if the product is serialized, indicate the serial number. Do not return products to our factory without our
prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL
NUMBER HAS BEEN REMOVED OR DEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION,
MAINTENANCE OR STORAGE, PRODUCTS MODIFIED WITHOUT INVACARE’S EXPRESS WRITTEN CONSENT INCLUDING, BUT NOT
LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTS DAMAGED BY REASON
OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT DAMAGED BY
CIRCUMSTANCES BEYOND INVACARE’S CONTROL, AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE
WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS.
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS
OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE
SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE
DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. THE APPLICATION OF ANY IMPLIED WARRANTY
WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN. INVACARE SHALL
NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, OR LIMITATION OF
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND REQUIREMENTS.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 OVERVIEW
Jymni Recliner Models Only
On all adjustable
anti-tippers
CAUTION
DO NOT recline without occupant. When the
chair is not occupied the back will raise abrup-
tly. Keep clear of the chair back when raising
Models with
Quick-Release Axles Only
or lowering to avoid injury.
1023096
WARNING
CAUTION
DETENT BALLS MUST BE SECURE-
LY SEATED IN RECESSED AREAS
OF AXLE BUSHINGS. ENSURE
THAT PLUNGER PIN IN HEAD END
OF AXLE IS FULLY RELEASED.
KEEP DETENT BALLS CLEAN.
SERVICE OF SPRING
LIFT MECHANISM TO
BE PERFORMED BY
PROPERLY TRAINED
AUTHORIZED SERVICE
PERSONNEL ONLY.
1022642
1001948
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 OVERVIEW
2.2 Typical Product Parameters
9000 JYMNI STANDARD AND LIGHT WEIGHT WHEELCHAIRS
OVERALL WIDTH
18 or 23 inches
REAR AXLE
Permanent* and quick-release
OVERALL DEPTH
(WITH RIGGINGS)
32 to 34½ inches
HANDRIMS
Composite* and aluminum, steel
SEAT WIDTH
SEAT DEPTH
10, 12 and 14inches
10, 12 and 14inches
WHEEL LOCKS
CASTER SIZE
UPHOLSTERY
Toggle lock -push or pull
6 x 1-inch Urethane in light or dark gray*
**SEAT-TO-FLOOR
14-INCH DEEP:
Standard Weight - Black vinyl*, midnight
blue vinyl or black nylon
15, 16 and 17 inches
10 AND 12-INCH DEEP: 15 and 16 inches
Light Weight - Black nylon*
BACK STYLE
Adjustable* - 1 inch increments; adjustable
angle - 5° to 20° in 5° increments
***WEIGHT
31 lbs (Jymni Standard Weight)
30 lbs (Jymni Light Weight)
BACK HEIGHT
14 or 15 inches
WEIGHT LIMIT
125 lbs (57 kg)
ARM STYLES
(FLIP BACK)
Space Saver* - Desk* or full length in
fixed* or adjustable height
SHIPPING WEIGHT 40 lbs (Jymni Standard Weight)
(APPROX.)
39 lbs (Jymni Light Weight)
Conventional - Desk or full length in fixed
or adjustable height
FRONT RIGGINGS
FRAME COLORS:
Swingaway footrests and elevating legrests
REAR WHEELS
20, 22*-inch composite; Urethane*,
pneumatic or pneumatic-flat free insert
Standard Weight - Chrome
Light Weight - Chrome, Silver Vein, Wet Black, Red, Deep Purple Sunny Yellow, Electric Red, Electric Purple, Royal
Blue w/Grape, Lavender, Electric Teal, Midnight Blue
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2 OVERVIEW
9000 JYMNI RECLINER WHEELCHAIRS
OVERALL WIDTH
19 or 23 inches
REAR AXLE
Permanent*
Aluminum
OVERALL DEPTH
(WITH RIGGINGS)
35½ to 39¼ inches
HANDRIMS
SEAT WIDTH
SEAT DEPTH
10, 12 and 14inches
10, 12 and 14inches
WHEEL LOCKS
CASTER SIZE
UPHOLSTERY
Toggle lock - push or pull
6 x 1-inch Urethane in light or dark gray*
Black nylon*
**SEAT-TO-FLOOR
14-INCH DEEP:
15, 16 and 17 inches
10 AND 12-INCH DEEP: 15, 16 and 17 inches
BACK STYLE
Reclining 95° to 160°
***WEIGHT
40 lbs
BACK HEIGHT
16 inches or 27 inches with headrest
WEIGHT LIMIT
125 lbs (57 kg)
ARM STYLES
(FLIP BACK)
Conventional - Desk or full length in fixed
or adjustable height
SHIPPING WEIGHT 49 lbs
(APPROX.)
FRONT RIGGINGS
Swingaway footrests and elevating legrests
REAR WHEELS
20, 22*-inch composite; Urethane*,
pneumatic or pneumatic-flat free insert
FRAME COLORS:
Chrome, Silver Vein, Wet Black, Red, Deep Purple Sunny Yellow, Electric Red, Electric Purple, Royal Blue w/Grape,
Lavender, Electric Teal, Midnight Blue
* These options are standard for this model.
** The seat-to-floor heights are based on urethane tires. If wheelchair is equipped with pneumatic (properly inflated) or
solid rubber tires, add ¼-inch to the measurements listed above. These heights can vary +/- ¼-inch due to tire wear and
manufacturing tolerances.
*** 12 x 12-inch Seat Frame with standard armrest and 90° footrest. Jymni Recliner includes headrest extension and pillow.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
3 Safety
The safety section contains important information for the safe operation and use of this product.
3.1 General Guidelines
WARNING
ƽ
DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and
any additional instructional material such as owner’s manuals, service manuals or instruction sheets supplied with this product or optional
equipment. If you are unable to understand the warnings, cautions or instructions, contact a healthcare professional, dealer or technical
personnel before attempting to use this equipment - otherwise, injury or damage may occur.
A qualified technician MUST perform the initial set up of this wheelchair. also, a qualified technician must perform all procedures specifically
indicated in the manual.
ACCESSORIES WARNINGS
Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by
other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.
ƽ
NOTICE
!
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Check all parts for shipping damage and test before using. In case of damage, DO NOT use. Contact Invacare/Carrier for further
instruction.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
3.2 Operating Information
Anti-tippers
WARNING
ƽ
Anti-tippers are specific to the different seat-to-floor angles and/or seat-to-floor heights. Refer to Anti-tippers/Wheel Locks on page 54 for
correct usage and adjustment. If these requirements cannot be achieved, DO NOT use the wheelchair. Contact a qualified technician. If
changing the seat-to-floor height with or without a change to seat-to-floor angle, the correct anti-tippers MUST be used to maintain a 1½
to 2-inch ground clearance.
Seat-to-floor angle of 0° or 3°: If so equipped, anti-tippers MUST be attached at all times. Inasmuch as the anti-tippers are an option for 0°
or 3° on this wheelchair (you may order with or without the anti-tippers), Invacare strongly recommends ordering the anti-tippers as a
safeguard for the wheelchair user.
Seat-to-floor angle of 6°: If changing the seat-to-floor angle to 6°, anti-tippers MUST be installed.
Anti-tippers MUST be fully engaged and release buttons fully protruding out of the adjustment holes.
Ensure both anti-tippers are adjusted to the same mounting hole.
ALWAYS use anti-tippers. When outdoors on wet, soft ground or on gravel surfaces, anti tippers may not provide the same level of
protection against tipover. Extra caution MUST be observed when traversing such surfaces.
Non-recliners Only - Inasmuch as anti-tippers are an option on this wheelchair (You may order non-recliners with or without the
anti-tippers), Invacare strongly recommends ordering anti-tippers as an additional safeguard for the wheelchair user. If so equipped,
anti-tippers MUST be attached and pointing down towards ground/floor at all times.
Recliners and Wheelchairs with 1-inch Forward Rear Wheel Positioner Only - Anti-tippers MUST be attached at all times.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
General Warnings
WARNING
ƽ
To determine and establish your particular safety limits, practice bending, reaching and transferring activities in several combinations in the
presence of a qualified healthcare professional before attempting active use of the wheelchair.
Avoid storing or using the wheelchair near open flame or combustible products. Serious injury or damage to property may result.
DO NOT stand on the frame of the wheelchair.
DO NOT use the footplate as a platform. When getting in or out of the wheelchair, make sure that the footplates are in the upward
position.
ALWAYS use the handrims for self-propulsion. Inasmuch as the handrims are an option on this wheelchair (you may order with our
without the handrims), Invacare strongly recommends ordering the handrims as an additional safeguard for the wheelchair user.
Invacare recommends that a non-folding device be installed to keep the wheelchair from being folded when left unoccupied in a public
place.
DO NOT operate on roads, streets or highways.
Hand Grips
WARNING
ƽ
ALWAYS check hand grips for looseness before using the wheelchair. If loose and/or worn, replace IMMEDIATELY.
When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are dry prior to use.
Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly. Failure to observe this warning
may result in injury to the user or bystanders.
If the wheelchair is exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, prior to use,
ensure that the handgrips DO NOT twist on the handle. Otherwise, damage or injury may occur.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Information for Healthcare Professionals/Assistants
WARNING
ƽ
When assistance to the wheelchair user is required, remember to use good body mechanics. Keep your back straight and bend your knees
whenever tilting the wheelchair or traversing curbs, or other impediments.
Make sure occupant’s hands and body are clear of all pinch points before reclining back. Use caution, otherwise injury may occur.
When learning a new assistance technique, have an experienced assistant help you before attempting it alone.
Lifting
WARNING
ƽ
DO NOT attempt to lift the wheelchair by any removable (detachable) parts. Lifting by means of any removable (detachable) parts of the
wheelchair may result in injury to the user or damage to the wheelchair.
Ramps, Slopes, Inclines and Obstacles
WARNING
DO NOT traverse, climb or go down ramps or slopes greater than 9°.
ƽ
DO NOT attempt to move up or down an incline with a water, ice or oil film.
DO NOT attempt to ride over curbs or obstacles. Doing so may cause your wheelchair to tip over and cause bodily harm to you or
damage to the wheelchair.
Repair and Service Information
WARNING
ƽ
Unless otherwise noted, all service and adjustment should be performed while the wheelchair is unoccupied.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Seat Positioning Strap
WARNING
ƽ
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on this wheelchair (you may order with or
without the seat positioning strap), Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the
wheelchair user. The seat positioning strap is a positioning strap only. It is not designed for use as a safety device withstanding high stress
loads such as auto or aircraft safety belts. If signs of wear appear, strap MUST be replaced IMMEDIATELY.
With regards to seat/chest positioning straps - it is the obligation of the DME dealer, therapists and other healthcare professionals to
determine if a seat/chest positioning strap is required to ensure the safe operation of this equipment by the user. Serious injury can occur
in the event of a fall from a wheelchair.
Tire Pressure
WARNING
ƽ
DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these
suggestions may cause the tire to explode and cause bodily harm. The recommended tire pressure is listed on the side wall of the tire.
Weight Limitation
WARNING
The 9000 Jymni wheelchairs have a weight limitation of 125 lbs (57 kg).
ƽ
Weight Training
WARNING
ƽ
Invacare does not recommend the use of its wheelchairs as a weight training apparatus. Invacare wheelchairs have not been designed or
tested as a seat for any kind of weight training. If occupant uses said wheelchair as a weight training apparatus, Invacare shall not be liable
for bodily injury or damage to the wheelchair and the warranty is void.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Wheel Locks
WARNING
ƽ
DO NOT attempt to stop a moving wheelchair with wheel locks. Wheel locks are not brakes.
If the wheelchair is equipped with push to lock wheel locks, elevating legrests, and wheel lock extension handles, the wheel lock extension
handles MUST be removed before swinging the elevating legrests to the side, otherwise injury or damage may result. Interference between
the top of the elevating legrest and the wheel lock extension handle causes the wheel lock to disengage.
Wheelchair Tie Down Restraints
WARNING
ƽ
Wheelchair users should NOT be transported in vehicles of any kind while in wheelchairs. As of this date, the Department of
Transportation has not approved any tie-down systems for transportation of a user while in a wheelchair, in a moving vehicle of any type.
It is Invacare’s position that users of wheelchairs should be transferred into appropriate seating in vehicles for transportation and use be
made of the restraints made available by the auto industry. Invacare cannot and does not recommend any wheelchair transportation
systems.
Wheelchair User
WARNING
ƽ
As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user.
However, final selection of the type of wheelchair to be used by an individual rests solely with the user and his/her healthcare professional
capable of making such a selection.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
3.3 Safety/Handling of Wheelchairs
Safety and handling of the wheelchair require the close attention of the wheelchair user as well as the assistant. This manual points out the most common
procedures and techniques involved in the safe operation and maintenance of the wheelchair. It is important to practice and master these safe techniques
until you are comfortable in maneuvering around the frequently encountered architectural barriers.
Use this information only as a basic guide. The techniques that are discussed on the following pages have been used successfully by many.
Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual. Invacare recognizes
and encourages each individual to try what works best for him/her in overcoming architectural obstacles that they may encounter. However, all
warnings and cautions given in this manual MUST be heeded. Techniques in this manual are a starting point for the new wheelchair user and assistant
with “safety” as the most important consideration for all.
Stability and Balance
WARNING
ƽ
The seat depth, back height/angle, seat angle, size/position of the front casters, seat-to-floor angle, position of the rear wheels, correct
anti-tipper as well as the end user’s disability or end user’s physical condition and capabilities directly relate to the stability of the wheelchair.
Any change to one or any combination may cause the wheelchair to decrease in stability. These adjustments MUST be performed by a
qualified technician.
Seat-to-floor heights have specific positions depending on rear wheel size, rear wheel position, front caster size/position and seat-to-floor
angle. These adjustments MUST be performed by a qualified technician.
Be aware that carrying heavy objects on your lap while occupying the wheelchair may adversely affect the stability of the wheelchair,
resulting in serious bodily injury to the user, damage to the wheelchair and surrounding property.
This wheelchair has been designed to accommodate one individual. If more than one individual occupies the wheelchair this may adversely
affect the stability of the wheelchair, resulting in serious bodily injury to the user, damage to the wheelchair and surrounding property.
(Recliner Models Only)
ALWAYS make sure that the wheelchair is stable before using the recliner option.
ALWAYS return the back to the upright position before lifting the wheelchair.
ALWAYS engage both wheel locks while reclining or inclining (sitting up) the wheelchair.
ALWAYS return the back to the upright position before lifting the wheelchair.
Ensure the spreader bar is attached and secured before using the Jymni Recliner.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
When changes to the left hand column occur, follow across the chart
and refer to the procedure that is checked (✓) to maintain the
proper stability, safety and handling of the wheelchair.
BACK HEIGHT
SEAT DEPTH
•
✓
•
✓
✓
•
✓
✓
✓
N/A
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
✓
✓
✓
BACK ANGLE
✓
✓
✓
✓
✓
SEATING SYSTEM
TILT ANGLE
✓
✓
✓
✓
✓
✓
✓
✓
•
✓
✓
✓
✓
N/A N/A
N/A N/A
N/A
•
N/A
•
N/A
✓
N/A N/A N/A N/A N/A
CASTER SIZE
✓
✓
✓
✓
✓
✓
N/A
N/A
N/A
N/A
✓
N/A N/A
N/A N/A
N/A N/A
N/A N/A
✓
✓
•
✓
✓
✓
•
N/A
N/A
N/A
N/A
•
✓
✓
✓
✓
✓
✓
✓
✓
CASTER POSITION
WHEEL SIZE
✓
•
✓
✓
WHEEL POSITION
USER CONDITION
SEAT HEIGHT
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
N/A N/A
N/A
✓
✓
N/A
✓
✓
To assure stability and proper operation of your wheelchair, you MUST maintain proper balance at all times. Your wheelchair has been designed to remain
upright and stable during normal daily activities as long as you DO NOT move beyond the center of gravity.
Virtually all activities which involve movement in the wheelchair have an effect on the center of gravity. Invacare recommends using seat/chest positioning
straps for additional safety while involved in activities that shift your weight.
DO NOT lean forward out of the wheelchair any further than the length of the armrests. Make sure the casters are pointing in the forward position whenever
you lean forward. This can be achieved by advancing the wheelchair and then reversing it in a straight line.
Many activities require the wheelchair owner to reach, bend and transfer in and out of the wheelchair. These movements will cause a change to the normal
balance, the center of gravity, and the weight distribution of the wheelchair. To determine and establish your particular safety limits, practice bending, reaching
and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair.
Proper positioning is essential for your safety. When reaching, leaning, or bending forward, it is important to use the front casters as a tool to maintain stability
and balance.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Reaching, Leaning and Bending Forward or Sideways
WARNING
DO NOT attempt to reach objects if you have to move
forward in the seat or pick them up from the floor by
reaching down between your knees.
ƽ
DO NOT attempt to reach or lift objects that would
cause you to shift weight to one side of the wheelchair.
Reaching or lifting objects on the side of the wheelchair
can cause the chair to tip over sideways.
DO NOT lean over the tope of the back upholstery to
reach objects behind you, as this may cause the
wheelchair to tip over.
Forward
FIGURE 1 Percentage of Weight Distribution
Position the front casters so that they are extended as far forward as
possible and engage wheel locks.
Backwards
Position wheelchair as close as possible to the desired object. Point front
casters forward to create the longest possible wheelbase. Reach back
only as far as your arm will extend without changing your sitting position.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Coping With Everyday Obstacles
Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair. Keep in mind your center of gravity
to maintain stability and balance.
Tipping
WARNING
DO NOT tip the wheelchair without assistance.
When lowering the front casters of the wheelchair, DO NOT let the wheelchair drop the last few inches to the ground This could result
in injury to the occupant and/or damage to the wheelchair.
ƽ
When tipping the wheelchair, an assistant should grasp the back of the wheelchair on a non-removable (non-detachable) part. Inform the wheelchair occupant
before tipping the wheelchair and remind him/her to lean back. Be sure the occupant’s feet and hands are clear of all wheels and/or pinch points.
After mastering the techniques of tipping the wheelchair, use one of the following methods to tackle curbs, short stairs, etc.
Method 1 - Wheelchair With Step Tubes
WARNING
When lowering the front casters of the wheelchair, DO
NOT let the wheelchair drop the last few inches to the
ground. This could result in injury to the occupant
and/or damage to the wheelchair.
ƽ
Place foot on the step tube and begin to tilt the wheelchair toward you.
Apply a continuous downward motion until the balance point is achieved
Step Tube
and the front casters clear the curb. At this point, the assistant will feel a
difference in the weight distribution.
FIGURE 3 Method 1 - Wheelchair With Step Tubes
Roll the wheelchair forward and slowly lower the front of the wheelchair in
one continuous movement onto the sidewalk. Push the wheelchair forward
until the rear wheels roll up and over the curb.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Method 2 - Wheelchair Without Step Tubes
This method requires two assistants. The second assistant should be
positioned at the front of the wheelchair lifting upward on a
non-removable (non-detachable) part of the wheelchair frame when
lifting the wheelchair and stabilizing the wheelchair when the wheelchair
is being lowered to the ground.
The first assistant should stand on the sidewalk and turn the wheelchair
so that the rear wheels are against the curb. Turn the anti-tippers so the
anti-tip wheels are pointing up. The wheelchair should be tilted back to
the balance point and, in one continuous upward movement, the rear
wheels should be pulled up and over the curb. DO NOT return the front
casters to the ground until the wheelchair has been pulled backward far
enough for the front casters to clear the edge of the curb.
Roll the wheelchair backward and slowly lower the wheelchair in one
continuous movement. Turn the anti-tippers so the anti-tip wheels are
facing down.
Stairways
WARNING
ƽ
Extreme caution is advised when it is necessary to move an occupied or unoccupied wheelchair up or down the stairs. Invacare
recommends that, if possible, the user be removed from the wheelchair prior to moving. Invacare recommends using two
assistants and making thorough preparations. Make sure to use only secure, non-detachable parts for hand-held supports.
Follow this procedure for moving the wheelchair between floors when an elevator is not available:
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Moving Up Stairs
1. If necessary, rotate the anti-tippers so the wheels are facing up.
2. One assistant (positioned behind the wheelchair), securely grasps a non-removable (non-detachable) part of the wheelchair for leverage and tilts the
wheelchair back to the balance point.
3. After the wheelchair has been tilted back to the balance point, the assistant behind the wheelchair backs the wheelchair up against the first step.
4. The second assistant (positioned in the front of the wheelchair), with a firm hold on a non-detachable part of the framework, lifts the wheelchair up and
on to the next stair above and steadies the wheelchair as the assistant behind the wheelchair places one foot on the next stair above and repeats process.
5. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway.
6. If necessary, rotate the anti-tippers so the wheels are facing down.
Moving Down Stairs
1. If necessary, rotate the anti-tippers so the wheels are facing up.
2. One assistant (positioned behind the wheelchair), securely grasps a
non-removable (non-detachable) part of the wheelchair for
leverage and tilts the wheelchair back to the balance point.
3. After the wheelchair has been tilted back to the balance point, the
assistant behind the wheelchair rolls the wheelchair up to the edge of
the first step.
4. The second assistant (positioned in the front of the wheelchair), with a
firm hold on a non-detachable part of the framework, lowers the
wheelchair down and on to the next stair below and steadies the
wheelchair as the assistant in the rear places one foot on the next stair
below and repeats process.
5. The wheelchair should not be lowered until the last stair has been
negotiated and the wheelchair has been rolled away from the stairway.
6. If necessary, rotate the anti-tippers so the wheels are facing down.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Escalators
WARNING
ƽ
DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.
3.4 Transferring To and From Other Seats
WARNING
ƽ
Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Turn both casters
parallel to the object you are transferring onto. Also be certain the wheel locks are engaged to help prevent the wheels from moving.
CAUTION
ƽ
When transferring, position yourself as far back as possible in the seat. This will help prevent damaged upholstery and the possibility of
the wheelchair tipping forward.
Position the wheelchair as close as possible alongside the seat to which
you are transferring, with the front casters pointing parallel to it.
Remove or flip up the armrest. Engage wheel locks. Swing away or
remove front rigging. Shift body weight into seat with transfer.
During independent transfer, little or no seat platform will be beneath
you. Use a transfer board if at all possible.
This activity may be performed independently provided
you have adequate mobility and upper body strength.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
3.5 Unfolding and Folding Wheelchair
WARNING
ALWAYS keep hands and fingers clear of moving parts to avoid injury.
DO NOT place hand or fingers on the underside of the seat frame rail when opening or closing the wheelchair.
DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H-blocks.
Invacare recommends that a non-folding device be installed to keep the wheelchair from being folded when left unoccupied in a public
place.
ƽ
Unfolding Sling Seat
1. Grasp the push closest to you.
2. Tilt the wheelchair towards you (raising the opposite wheel and
caster off the ground/floor).
3. Push downward on the seat rail closest to you where the seat
upholstery is attached until the wheelchair is fully open.
4. Engage both wheel locks, open the footrest/legrest for clearance
and transfer into the wheelchair.
FIGURE 7 Unfolding Sling Seat
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3 SAFETY
Folding Sling Seat
If the wheelchair is equipped with carry straps, the
wheelchair may be folded by pulling up on the straps.
1. Swing footrest/legrest in locked position to the front of the
wheelchair.
2. Pivot footplates upward to vertical position.
3. With both hands, grasp the middle of the seat upholstery at the
front and back edge and flip up. Or, tilt the wheelchair to one side
and close by the push handles.
Unfolding/Folding Solid Seat Model Wheelchairs
1. From behind the wheelchair, grasp the right hand edge of the solid
seat.
2. Raise the seat to the hinged side.
3. Swing footrest/legrest in locked position to the front of the
wheelchair.
4. Pivot footplates upward to vertical position.
5. With both hands, grasp the middle of the seat upholstery at the
front and back edge and lift up or tilt the wheelchair to one side and
close by the push handles.
FIGURE 9 Unfolding/Folding Solid Seat Model Wheelchairs
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4 SAFETY INSPECTION/TROUBLESHOOTING
4 Safety Inspection/Troubleshooting
Every six months or as necessary, take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning
will reveal loose or worn parts and enhance the smooth operation of your wheelchair. To operate properly and safely, your wheelchair
MUST be cared for just like any other vehicle. Routine maintenance will extend the life and efficiency of your wheelchair.
4.1 Safety Inspection Checklist
Initial adjustments should be made to suit your personal body structure and preference. Thereafter follow these maintenance procedures:
Inspect/Adjust Initially
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
Ensure that the wheelchair rolls straight (no excessive drag or pull to one side).
Inspect for loose or missing hardware on frame and crossbraces.
Inspect for bent frame or crossbraces.
Check that the wheel locks DO NOT interfere with tires when rolling.
Check that the wheel lock pivot points are free of wear and looseness.
Check that the wheel locks are easy to engage.
Ensure that the wheel locks prevent the wheelchair from moving when engaged.
Inspect the seat and back for rips and sagging.
Inspect the seat and back for loose or broken hardware.
Inspect the back cane hand grips for wear/looseness/deterioration.
Inspect seat positioning strap for any signs of wear. Ensure buckle latches. Verify hardware that attaches strap to frame is secure and undamaged.
Replace if necessary.
❑
❑
Inspect tires for flat spots and wear.
Check pneumatic tires for proper inflation.
CAUTION
ƽ
As with any vehicle, check the wheels and tires periodically for cracks and wear. Replace if damaged.
❑
❑
❑
❑
If equipped, check that quick-release axles lock properly. Lubricate if necessary.
Check that there is no excessive side movement or binding in the rear wheels when lifted and spun.
Inspect rear wheels for cracked, bent or broken spokes.
Ensure all spokes are uniformly tight.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4 SAFETY INSPECTION/TROUBLESHOOTING
❑
❑
❑
❑
❑
❑
❑
❑
Inspect handrims for signs of rough edges or peeling.
Inspect axle assembly for proper tension by spinning caster. Caster should come to a gradual stop.
Adjust front casters/forks bearing system if wheel wobbles noticeably or binds to a stop.
Ensure wheel bearings are clean and free of moisture.
Check headtube locknuts for tightness.
Inspect casters for cracks and wear.
Inspect front casters for cracked, bent or broken spokes.
Clean upholstery and armrests.
Inspect/Adjust Weekly
❑
❑
❑
❑
❑
❑
❑
❑
Ensure that the wheel locks prevent the wheelchair from moving when engaged.
Inspect tires for flat spots and wear.
Check pneumatic tires for proper inflation.
If equipped, check that quick-release axles lock properly. Lubricate if necessary.
Inspect rear wheels for cracked, bent or broken spokes.
Ensure all spokes are uniformly tight.
Inspect axle assembly for proper tension by spinning caster. Caster should come to a gradual stop.
Inspect front caster for cracked, bent or broken spokes.
Inspect/Adjust Monthly
❑
❑
❑
❑
❑
Ensure that the wheelchair rolls straight (no excessive drag or pull to one side).
Check that the wheel locks DO NOT interfere with tires when rolling.
Check that the wheel lock pivot points are free of wear and looseness.
Inspect seat and back for loose or broken hardware.
Inspect seat positioning strap for any signs of wear. Ensure buckle latches. Verify hardware that attaches strap to frame is secure and undamaged.
Replace if necessary.
❑
❑
❑
❑
Inspect back cane hand grips for wear/looseness/deterioration.
Adjust front casters/forks bearing system if wheel wobbles noticeably or binds to a stop.
Ensure wheel bearings are clean and free of moisture.
Check headtube locknuts for tightness.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4 SAFETY INSPECTION/TROUBLESHOOTING
Inspect/Adjust Periodically
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
Inspect frame and crossbraces for loose or missing hardware.
Inspect for bent frame or crossbraces.
Check that wheel locks are easy to engage.
Inspect seat and backs for rips and sagging.
Check that there is no excessive side movement or binding in the rear wheels when lifted and spun.
Inspect handrims for signs of rough edges or peeling.
Adjust front casters/forks bearing system if wheel wobbles noticeably or binds to a stop.
Inspect casters for cracks and wear.
Ensure that casters are free of debris.
Ensure wheel bearings are clean and free of moisture.
Clean upholstery and armrests.
Check that all labels are present and legible. Replace if necessary.
4.2 Troubleshooting
Chair Veers Chair 3 Wheels Sluggish Turn
Casters
Squeaks
and Rattles
Looseness
in Chair
Solutions
Right/Left
or Performance Flutter
X
X
X
X
X
X
X
Check tires for correct and equal pressure
Check for loose nuts and bolts.
X
X
X
X
X
X
Check caster headtube angle.
Check that rear wheels are equally spaced away from seat frame.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4 SAFETY INSPECTION/TROUBLESHOOTING
4.3 Maintenance
Maintenance Safety Precautions
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may result.
DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame tubing.
Suggested Maintenance Procedures
1. Before using your Jymni Series wheelchair, make sure all nuts and bolts are tight.
2. Check all parts for damage or wear and replace.
3. Check all parts for proper adjustment.
4. Standard and Light Weight Models ONLY - Keep quick-release axles free of dirt and lint to ensure positive locking and proper operation. Refer
®
5. Oil quick-release axles at least once a month (3-in-1 oil or equivalent).
WARNING
DO NOT use the wheelchair unless it has the proper tire pressure (p.s.i.).
DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm.
The recommended tire pressure is listed on the sidewall of the tire.
ƽ
CAUTION
As with any vehicle, check the wheels and tires periodically for cracks and wear. Replace if damaged. Refer to Replacing/Repairing Rear
6. The rear wheels, casters and tires should be checked periodically for cracks and wear, and should be replaced by a qualified technician if damaged
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4 SAFETY INSPECTION/TROUBLESHOOTING
7. Periodically adjust wheel locks in correlation to tire wear. Refer to Adjusting Patient-Operated Wheel Locks on page 58.
Tire wear is excessive if:
Pneumatic Tires - there is missing tread or the tires are bald.
Urethane Tires - there are cuts, surface defects or the tires are loose on the rims.
Rubber Tires - 30% or more of the tire has worn away.
Invacare recommends that tires and casters be replaced every five years.
8. Periodically check handrims to ensure they are secured to the rear wheels. If loose, have them tightened by a qualified technician.
®
9. Periodically check caster wheel bearings to make sure they are clean and free from moisture. Use a Teflon lubricant if necessary.
10. Check upholstery for sagging, rips or tears.
11. Clean upholstery with mold soap and water.
12. Replace any labels that are missing, worn, or torn. Refer to Label Locations on page 8 for a listing of labels and their locations.
WARNING
ƽ
When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are dry prior to
use. Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly. Failure to observe this
warning may result in injury to the user or bystanders.
13. Hand grips should be checked monthly for wear/looseness/deterioration. Clean if desired. Replace if looseness or deterioration is found.
Replacing/Repairing Rear Wheel Tire/Tube
WARNING
Replacement of rear wheel tube must be performed by a qualified technician.
ƽ
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4 SAFETY INSPECTION/TROUBLESHOOTING
Replacing/Repairing Caster Tire/Tube
WARNING
ƽ
Replacement of front caster tire or tube MUST be performed by a qualified technician.
As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced when necessary.
For pneumatic tires, replacement of the tire or tube must be performed by a qualified technician.
4.4 Transporting the Invacare Jymni
1. Remove the seating system. Refer to the seating system Owner’s Manual for installation and removal of the seating system.
2. Remove the footrests.
3. Remove the rear wheels.
4. Remove the armrests.
5. Remove the anti-tippers.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5 FRONT RIGGINGS
5 Front Riggings
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
5.1 Installing/Removing the Swingaway Footrest Assembly
Installing
Footrest Release Lever
Hinge Plates
1. Turn the swingaway footrest assembly to the side (so that the
footplate is perpendicular to the wheelchair).
2. Install the hinge plates on the swingaway footrest assembly onto the
hinge pins on the wheelchair frame.
3. Push the swingaway footrest assembly towards the inside of the
wheelchair until it locks into place.
4. Repeat this procedure for the other footrest assembly.
The footplates will be facing each other when locked in
place.
Hinge Pins
Removing
1. Push the footrest release lever toward rear of chair.
2. Rotate swingaway footrest assembly outward.
3. Lift the swingaway footrest assembly off of the hinge pins.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5 FRONT RIGGINGS
5.2 Swingaway Footrest Height Adjustment
J932A-14
Lay the assembly on a flat surface to simplify this
procedure.
Upper Footrest Support
2. Remove impact guards and/or calf strap, if necessary.
3. Perform one of the following:
Bolt and
Locknut
A. Wheelchairs equipped with 80° swingaway footrest (Model
J923A-14):
Lower Footrest
Assembly
•
•
•
Loosen, but do not remove the bolt and lock nut that secure
the lower footrest assembly to the upper footrest support.
Reposition the lower footrest assembly to the desired
height.
J932A and J933A
Securely tighten the bolt and locknut.
B. Wheelchairs equipped with 70° swingaway footrest (Model
Number J932A) OR 90° swingaway footrest (Model J933A):
•
•
Remove the bolt, locknut and four washers that secure the
lower footrest assembly to the upper footrest support.
Align the mounting hole of the lower footrest assembly with
the desired height adjustment hole in the lower footrest
support.
Upper Footrest Support
Lower Footrest
Assembly
•
Reinstall the bolt through the desired height adjustment hole
in the lower footrest assembly and through the mounting
hole in the lower footrest support. Securely tighten with the
locknut and four washers.
Locknut
Washers
4. Repeat this procedure for the other footrest, if necessary.
Bolt
5. Replace impact guards and/or calf strap, if necessary.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5 FRONT RIGGINGS
5.3 Heel Loop Replacement
Swingaway Footrests/Elevating Legrest (J932A, J932A-14, J933A and J934A)
1. Remove the four mounting screws and washers that secure the heel loop to the BOTTOM of the footrest.
2. Remove the heel loop from the footrest.
Elevating Legrest (J934A-14 ONLY)
1. Loosen, but do not remove the bolt and locknut that secure the lower half of the footrest to the swingaway footrest assembly.
2. Remove the lower footrest assembly.
3. Remove the mounting screw and locknut that secure the heel loop to the footrest.
4. Slide heel loop over cane of the footrest assembly.
5. Replace heel loop.
6. Reverse STEPS 1-4 to reassemble.
When securing the heel loop to the footrest assembly, tighten the mounting screw and locknut until the spacer is secure.
JA932A,
JA932A-14,
Bolt and Locknut
Mounting Screw
J933A, J934A
Heel Loop
Spacer
Heel Loop
Footrest
Cane
J934A-14
Washer
Mounting Screw
Lower Footrest
Assembly
Locknut
FIGURE 3 Adjusting the Elevating Legrest Assembly
36
Download from Www.Somanuals.com. All Manuals Search And Download.
5 FRONT RIGGINGS
5.4 Installing/Removing Elevating Legrest Assembly
Installing
Step 1
Calfpad Assembly
1. Place elevating legrest assembly on the outside of the wheelchair
and install the hinge plates onto the hinge pins on the wheelchair
frame.
Lower Footrest Assembly
Footplate
2. Rotate elevating legrest assembly toward the inside of the
wheelchair until it locks in place.
3. Repeat this procedure for other legrest assembly.
Bolt and Locknut
The footplates will be facing each other when locked in
place.
4. After seated in wheelchair, adjust the legrest to correct height.
Steps 2 & 3
Hinge Plates
Removing
1. To release the elevating legrest assembly, push the legrest release
handle toward the inside of the wheelchair (facing the front of the
wheelchair) and swing the legrest assembly to the outside of the
wheelchair.
Elevating Legrest
Assembly
2. Lift the elevating legrest assembly off of the hinge pins.
Hinge Pins
Legrest Release
Handle
J934A-14 shown.
J934A installs the same way.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5 FRONT RIGGINGS
5.5 Adjusting the Elevating Legrest Assembly
Detail “A”
Raising Legrest Assembly
Calfpad
1. Assistant should grab hold of the lower legrest assembly and raise
elevating legrests until the desired height is obtained.
Lowering Legrest Assembly
Elevating Legrest
Assembly
1. Support user leg with one hand.
2. Perform one of the following:
Washers
Mounting Screws
•
Model J934A Elevating Legrest - Push release lever down with
other hand.
Detail “B”
•
Model J934A-14 Elevating Legrest - Push release lever forward
with other hand.
3. Gently, lower user leg down and rest against the legrest.
Adjusting Calfpad
Release Lever
Nut
Nut
2. Remove the two mounting screws and washers securing the calfpad
to the elevating legrest as shown in Detail “A”.
3. Position the calfpad in one of the two height positions.
Lower Legrest
Assembly
4. Reinstall the two mounting screws and washers securing the calfpad
to the elevating legrest. Securely tight.
Adjusting Height
Release
Lever
1. Adjust footrest to correct height by loosening the nut and sliding
the lower legrest assembly up or down until desired height is
achieved as shown in Detail “B”.
Lower Legrest Assembly
2. Securely tighten nut.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
6 ARMS
6 Arms
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
6.1 Adjusting Armrest Height
Armrest
WARNING
Make sure the height adjustment lever is in the locked
Height
Adjustment
Lever
ƽ
position before using the wheelchair.
1. Unlock the armrest by flipping the height adjustment lever on the
top front of the armrest to the up (horizontal) position.
Locked (Vertical)
2. Adjust armrest to one of five positions.
Height adjustment lever MUST be in the unlocked
position when placing armrest into the arm assembly.
3. Lock the armrest by pressing the height adjustment lever into the
down (vertical) position when the desired armrest height is
achieved.
Unlocked (Horizontal)
4. Repeat STEPS 1-3 for other armrest.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
6 ARMS
6.2 Using Swing-Back Arms
WARNING
ƽ
Make sure the armrest release lever is in the locked position before using the wheelchair.
Front
1. Unlock the swing-back arms by rotating the armrest release lever
toward the outside of the wheelchair.
Swing Back Arm
2. Pull the front of the swing-back arm straight up/out of the arm
socket and towards the rear of the wheelchair.
Armrest
Release
Lever
3. To use the swing-back arm, push the swing-back arm towards the
front of the wheelchair and then downward into the arm socket.
Armrest release lever MUST be in the unlocked position
4. Lock the swing-back arms by rotating the armrest release lever
towards the inside of the wheelchair.
when placing armrest into the arm sockets.
Rear
Arm Socket
40
Download from Www.Somanuals.com. All Manuals Search And Download.
6 ARMS
6.3 Removing or Replacing Armrest
WARNING
ƽ
Make sure the armrest release lever is in the locked position before using the wheelchair.
Removing Armrests
Armrest
1. Unlock the armrest by turning the armrest release levers towards
the outside of the wheelchair.
Rear Arm
Post
Armrest Release
Lever
2. Lift armrest completely out of arm sockets from the wheelchair.
Replacing Armrests
Armrest Release
Lever
Armrest release lever MUST be in the unlocked position
1. Place armrest into arm sockets located on the side of the
wheelchair.
Arm Socket
when placing armrest into the arm sockets.
Arm Socket
2. Lock the armrest by turning the armrest release levers towards the
inside of the wheelchair.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
6 ARMS
6.4 Replacing Desk/Full Length Armrest Pad (Fixed
Height Arms Only)
Mounting Screws
Armrest Pad
1. Remove the mounting screws that secure the armrest pad to the
armrest assembly.
Armrest
Assembly
2. Replace armrest pad and securely tighten with the existing
mounting screws.
Clothing
Guard
6.5 Replacing Clothing Guards (Fixed Height Arms
Only)
1. Remove the four mounting screws that secure the existing clothing
guard to the armrest assembly.
Mounting Screws
Mounting Screws
2. Install new clothing guard and securely tighten with the existing
mounting screws.
6.6 Converting Between Space Saver and Conventional Arms
Space Saver arms DO NOT work with the following:
•
•
Adjustable angle back option
Jymni Recliner
For this procedure, refer to FIGURE 5 on page 43.
2. Remove the locknut and hex screw that secure the arm socket to the wheelchair frame.
3. Repeat STEP 2 for the opposite side of the wheelchair.
4. Reposition the arm socket to one of two positions:
A. For conventional arms - position arm socket on outside of frame.
B. For space saver arms - position arm socket on inside of frame.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
6 ARMS
Make sure arm sockets sit flush against the wheelchair frame.
5. Reinstall the hex screw and locknut that secure the arm socket to the wheelchair frame and securely tighten.
6. Repeat STEP 5 for the opposite side of the wheelchair.
The rear wheel axle spacer is needed conventional arms. It is not needed for spacer saver arms.
7. Refer to the following to determine the rear wheel axle spacer needed:
A. Conventional - 5/8-inch
B. Space Saver - 1/8-inch
8. To install the rear wheel axle spacer, refer to Refer to Removing/Installing Rear Wheels on page 48.
Space Saver Arm Position
Conventional Arm
Arm Socket (Outside of
Wheelchair Frame)
Position
Arm Socket (Inside of
Wheelchair Frame)
Hex Screw
Locknut
Hex Screw
Locknut
Left Side of
Wheelchair Frame
Wheelchair Frame
Right Side of
Wheelchair Frame
43
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND BACK
7 Seat and Back
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
The procedures in this section apply to non-recliner models only. For recliner models, refer to Recliner on page 59.
7.1 Replacing Seat Upholstery
1. Remove the mounting screws that secure the existing seat upholstery to the seat rails.
10 and 12 inch seat depth has 8 mounting screws and 14 inch seat depths have 10 mounting screws.
2. Remove the existing seat upholstery from the seat rails.
3. Install new seat upholstery by reversing STEPS 1-2.
10 or 12-inch Seat Depth
Mounting Screw
Seat Upholstery
Seat Rail
Wheelchair Frame
44
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND BACK
7.2 Replacing Back Upholstery
1. Remove the two mounting screws and washers that secure the existing back upholstery to the back canes (Detail “A”).
2. Remove the two mounting screws and locknuts that secure one back cane to the wheelchair frame (Detail “B”).
It is necessary to remove only one back cane to replace the back upholstery.
3. Pull the loose back cane out of the existing back upholstery.
4. Pull the existing back upholstery up and over the mounted back cane.
5. Install the new back upholstery over the mounted back cane.
6. Slide the loose back cane through the new back upholstery.
7. Secure the back cane to the wheelchair frame with the two mounting screws, spacers and locknuts.
8. Secure the new back upholstery to the back canes with the existing mounting screws and washers.
Detail “A”
Detail “B”
Back Upholstery
Washer
Back Cane
Wheelchair Frame
Mounting
Screws
Locknuts
Mounting Screws
Back Cane
45
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND BACK
7.3 Adjusting Back Height
WARNING
ƽ
The seat depth, back height/angle, seat angle, size/position of the front casters, size/position of the rear wheels, anti-tipper model, as well
as the user condition directly relate to the stability of the wheelchair. Any change to one or any combination of these may cause the
wheelchair to decrease in stability. These adjustments must be performed by a qualified technician.
Back canes MUST be adjusted to the same height.
1. Remove the two mounting screws and locknuts that secure the two back canes to the wheelchair frame.
2. Reposition the back canes to one of the two height adjustment mounting holes.
•
•
14 inch - Mounting holes* 1 and 2
15 inch - Mounting holes* 2 and 3
Mounting holes numbered from bottom to top for reference only. (There are no numbers on the back canes or wheelchair frame.)
3. Reinstall the two allen screws and locknuts that secure the back canes to the wheelchair frame and securely tighten.
Height Adjustment
Back Cane
Mounting Holes
3
2
1
Wheelchair
Frame
The two mounting screws and locknuts that secure the back
cane to the wheelchair frame are not shown for clarity.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
7 SEAT AND BACK
7.4 Adjusting Back Angle - Standard/Light Weight Adjustable Angle Back Model Only
WARNING
ƽ
The back angle directly relates to the stability of the wheelchair. Any change may decrease the wheelchair’s stability. Adjusting Back Angle
MUST be performed by a qualified technician.
7.5 Adjusting Seat Width and Depth
WARNING
ƽ
The seat depth directly relates to the stability of the wheelchair. Any change may decrease the wheelchair’s stability. Adjusting Seat Width
and Depth MUST be performed by a qualified technician.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
8 REAR WHEELS
8 Rear Wheels
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
Except where noted, the procedures in this section apply to non-recliner models only. For recliner models, refer to Recliner on page 59.
8.1 Removing/Installing Rear Wheels
Wheelchair Frame
WARNING
Lock Nut
ƽ
Only a qualified technician may change the size of the
rear wheel or the seat-to-floor height.
Axle Mounting Positions
Rear Wheel
Permanent Axles
If replacing the same size rear wheel, note the mounting
position on the wheelchair frame for proper
reinstallation of the new rear wheel.
Axle Spacer
Dust Cap
1. Remove the dust cap (if applicable), mounting screw and locknut
that secure the rear wheel and axle spacer to the wheelchair.
2. Repeat STEP 1 for the opposite rear wheel.
Mounting Screw
3. To reinstall the rear wheel onto the wheelchair, reverse STEPS 1-2.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
8 REAR WHEELS
Quick-Release Axles
WARNING
ƽ
NEVER use quick-release axles on the recliner.
If replacing the same size rear wheel, note the mounting position on the wheelchair frame for proper reinstallation of the new rear wheel.
1. Push the detent pin in the tip of the quick-release axle (with wheel) and pull the axle out through the opening in the center of the rear wheel and axle spacer.
2. Push the detent pin in the tip of the quick-release axle again and pull
Detail “A” - Detent balls and detent pin
the axle out of the rear wheel.
Axle Bushing
3. Repeat STEPS 1-2 for the opposite rear wheel.
Outside of
Wheelchair
4. To reinstall the rear wheel onto the wheelchair, reverse STEPS 1-3.
Inside of
Wheelchair
WARNING
ƽ
Detent Balls
Quick-Release Axle
Make sure the detent pin and detent balls of the
quick-release axle are fully released before operating the
wheelchair.
Detent Pin
Wheelchair Frame
The detent balls MUST be protruding past the inside of
the rear wheel axle bushing for a positive lock (Detail
“A”).
Axle Mounting Positions
Rear Wheel
Keep detent balls clean.
Invacare recommends inserting quick-release axles with
the detent pin to the inside of the wheelchair to prevent
accidental release during contact activities.
Quick Release Axle
Axle Spacer
5. If the detent balls are not protruding past the inside of the axle bushing
or there is too much side-to-side movement of the rear wheel assembly,
49
Download from Www.Somanuals.com. All Manuals Search And Download.
8 REAR WHEELS
8.2 Adjusting the Quick-Release Axle
WARNING
ƽ
Never use quick-release axles on recliner wheelchairs.
1. Remove rear wheel and quick-release axle from the wheelchair. Refer to Removing/Installing Rear Wheels on page 48.
2. Depress detent pin in the quick-release axle and slide axle through the rear wheel hub.
3. Release detent pin ensuring that the detent balls are fully released.
4. Increase or decrease end play by adjusting the locknut on the end
of the quick-release axle.
Locknut
WARNING
Wheelchair Frame
ƽ
Make sure the detent pin and detent balls of the
quick-release axle are fully released before operating the
wheelchair.
Locking Pins
Detent
Pin
Keep detent balls clean.
Axle Spacer
Quick-Release Axle
Rear Wheel
Hub
50
Download from Www.Somanuals.com. All Manuals Search And Download.
8 REAR WHEELS
8.3 Replacing Rear Wheel Handrim
WARNING
ƽ
If the wheelchair is equipped with permanent axles, this procedure must be performed by a qualified technician.
1. Remove the rear wheel from the wheelchair. For non-recliner models,
Mounting Screw
2. Remove the mounting screws that secure the handrim to rear wheel.
Rear Wheel
3. Remove the existing handrim.
4. Install the new handrim by reversing the preceding steps.
WARNING
Make sure detent pin and detent balls of the
quick-release axles are fully released before operating
the wheelchair.
ƽ
6. If the detent balls of the quick-release axles (if applicable) are not
protruding past the inside of the axle bushing or there is too much
movement of the rear wheel assembly in a back and forth position,
Handrim
7. Repeat STEPS 1-6 for the opposite rear wheel if necessary.
8.4 Replacing/Repairing Rear Wheel Tire/Tube
WARNING
ƽ
Replacement of rear wheel tire or tube MUST be performed by a qualified technician.
CAUTION
ƽ
As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
9 FRONT CASTERS
9 Front Casters
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
9.1 Installing/Replacing Front Casters and Forks
1. Remove the dust cover.
2. Remove the locknut that secures the fork to the caster headtube.
3. Drop the front caster and fork out of the caster headtube.
4. Slide in the new front caster and fork.
Dust Cover
Locknut
5. Reassemble by reversing STEPS 1-3.
6. Repeat STEPS 1-5 for the opposite front caster.
7. To properly tighten caster journal system and guard against flutter,
perform the following check:
Caster Headtube
A. Tip back of wheelchair to floor.
B. Pivot both forks and casters to top of their arc simultaneously.
FrontCaster and
Fork
C. Let casters drop to bottom of arc (wheels should swing once
to one-side, then IMMEDIATELY rest in a straight downward
position).
D. Adjust locknuts according to freedom of caster swing.
8. Test wheelchair for maneuverability.
9. Readjust locknuts if necessary, and repeat STEPS 7-8 until correct.
10. Snap dust cover over the locknut and stem.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
9 FRONT CASTERS
9.2 Replacing/Repairing Front Caster Tire/Tube
WARNING
ƽ
Replacement of front caster tire or tube MUST be performed by a qualified technician.
CAUTION
ƽ
As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced.
9.3 Adjusting Front Caster Mounting
WARNING
ƽ
Front caster mounting adjustments MUST be performed by a qualified technician.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
10 ANTI-TIPPERS/WHEEL LOCKS
10 Anti-tippers/Wheel Locks
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
The procedures in this section apply to non-recliner models only except where noted. For the recliner model, refer to Recliner on
10.1 Installing/Adjusting Anti-tippers
WARNING
ƽ
Anti-tippers are specific to the different seat-to-floor angles and/or seat-to-floor heights. Refer to the chart in this section of the manual
for correct usage and adjustment. If these requirements cannot be achieved, DO NOT use the wheelchair. Contact an Invacare dealer or
qualified technician. Any changes to the seat-to-floor angle or seat-to-floor height may require different anti-tippers.
If changing the seat-to-floor height with or without a change to seat-to-floor angle, the correct anti-tippers MUST be used to maintain a
1-1/2 to 2-inch ground clearance.
Seat-to-floor height (which includes changing rear wheel size): If changing the seat-to-floor height with or without changing the rear
wheel size, the correct anti-tippers MUST be ordered to maintain a 1-1/2 to 2-inch ground clearance.
Non-recliners Only - Inasmuch as the anti-tippers are an option on this wheelchair (You may order with or without the anti-tippers),
Invacare strongly recommends ordering the anti-tippers as an additional safeguard for the
wheelchair user.
Recliners and Wheelchairs with 1-Inch Forward Rear Wheel Positioners Only - Anti-tippers MUST BE attached at all times.
Anti-tippers MUST be fully engaged. Ensure that the release buttons of the anti-tipper fully protrudes out of the hole on the bottom of
the wheelchair frame and out of hole in the adjustment tube.
Ensure both anti-tippers are adjusted to the same height.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
10 ANTI-TIPPERS/WHEEL LOCKS
Installing Anti-Tippers
To ensure the correct model anti-tipper is used refer to the Anti-tipper Identification Chart below. Measurements for anti-tippers are
approximate and are taken with extension tube in top hole position Detail “A”.
REAR WHEEL SIZE
20 inch
ANTI-TIPPER LENGTH
9 inches
ANTI-TIPPER PART NUMBER
1101959
1058752
22 inch
9-5/8 inches
1. Depress the release buttons and insert the anti-tippers with the
anti-tipper wheels pointing toward the ground/floor into the
wheelchair frame tubing as shown in FIGURE 1.
Anti-Tipper
Wheels
Anti-Rattle
2. Measure the distance between the bottom of the anti-tipper wheels
and the ground/floor.
Anti-Tipper
A 1½ to 2-inch clearance between the bottom of the
Release Buttons
anti-tipper wheels and the ground/floor MUST be
maintained at all times.
Rear Frame
Tubing
3. If the distance between the bottom of anti-tipper wheels and the
ground/floor is not 1½ to 2-inches, adjust anti-tippers. Refer to
Detail “A”
Top Position
4. If necessary, reverse STEPS 1-2 to remove the anti-tippers.
Anti-Tippers
Anti-Tipper
Length
55
Download from Www.Somanuals.com. All Manuals Search And Download.
10 ANTI-TIPPERS/WHEEL LOCKS
Adjusting Anti-Tippers
A 1½ to 2-inch clearance between the bottom of the anti-tipper wheels and the ground/floor MUST be maintained at all times.
1. Place the wheelchair on a flat, level surface.
On recliner models, ensure back canes are in the upright position before determining 1-1/2 to 2-inch clearance.
2. Press the release buttons on the wheeled portion of the anti-tipper and slide it up or down to achieve the 1-1/2 to 2-inch clearance (Detail “A”).
3. Check to make sure that the release buttons are fully engaged in adjustment holes and ensure both anti-tippers are adjusted to the same height.
4. Check to make sure that a 1-1/2 to 2-inch clearance between the bottom of the anti-tipper wheels and the ground/floor has been achieved
BEFORE using the wheelchair.
5. Repeat STEPS 1-3 until 1-1/2 to 2-inch clearance is achieved.
Detail “A”
Detail “B”
Anti-Tipper
Height
Release Buttons
2 inches
1½ inches
Anti-Tipper
Length
56
Download from Www.Somanuals.com. All Manuals Search And Download.
10 ANTI-TIPPERS/WHEEL LOCKS
10.2 Using Patient Operated Wheel Locks
Push wheel lock handle forward away from the tire to
engage wheel lock
WARNING
After any adjustments, repair or service and before use,
make sure all attaching hardware is tightened securely.
Otherwise injury or damage may occur.
ƽ
Unlocked Position
Locked Position
Wheel Lock
WARNING
ƽ
DO NOT attempt to stop a moving wheelchair with
wheel locks. Wheel locks are not brakes.
Pull wheel lock handle toward
the tire to disengage wheel lock
Push-To-Lock
Position wheelchair on a flat, level surface to perform
this procedure.
1. Ensure the wheelchair is not moving before engaging the wheel
locks.
Pull wheel lock handle toward the tire to engage wheel lock
2. Depending on the model of wheel lock installed on the wheelchair,
perform one of the following:
Locked Position
Wheel Lock
•
Push-to-Lock - To engage, push the wheel lock handle
forward.
•
Pull-to-Lock - To engage, pull the wheel lock handle backward.
3. Disengage the wheel locks by reversing STEP 2.
Unlocked Position
Push wheel lock handle away from
the tire to disengage wheel lock
Pull-To-Lock
57
Download from Www.Somanuals.com. All Manuals Search And Download.
10 ANTI-TIPPERS/WHEEL LOCKS
10.3 Adjusting Patient-Operated Wheel Locks
If wheels are pneumatic, before adjusting or replacing the wheel lock assemblies, ensure that the tires are inflated to the recommended psi
on the side wall of tire. The recommended tire pressure is located on the side wall of the tire.
1. Disengage the wheel locks.
Bolt and Locknut
Mounting Positions
Wheel Lock
2. Loosen the bolt and locknut that secure the wheel lock to the
wheelchair frame.
3. Reposition the wheel lock so that when engaged, the wheel lock shoe
embeds the tire 1/8-inch (3/16-inch for pneumatic tires) and holds the
occupied wheelchair in place when pushed.
Wheel Lock Handle
4. Securely tighten the bolt and locknut or socket screws securing the
wheel lock to the wheelchair frame.
5. Engage the wheel lock.
6. Measure the distance the wheel lock is embedded into the tire.
Any wheel lock adjustment should embed the wheel lock
Wheel Lock Shoe
Rear Wheel
shoe at least 1/8-inch (3/16-inch if pneumatic tire) into the
tire when engaged.
7. Repeat STEPS 1-6 until the wheel lock shoe embeds the tire 1/8-inch
(3/16-inch for pneumatic tires) and holds the occupied wheelchair in
place when pushed.
Detail “A”
8. If the measurement of 1/8-inch (3/16-inch for pneumatic tires) can not
be achieved, remove the bolt and locknut that secure the wheel lock
to the wheelchair frame and mount the wheel lock in the remaining
mounting position.
9. Repeat STEPS 1-8 for the opposite wheel lock.
10. Engage both wheel locks and ensure the occupied wheelchair is held in
place when pushed.
1/8-inch (3/16-inch pneumatic tires)
Wheel Lock Shoe
WARNING
If wheel locks DO NOT hold the occupied wheelchair in
place, contact a qualified technician. Otherwise injury or
damage may occur.
Tire
ƽ
58
Download from Www.Somanuals.com. All Manuals Search And Download.
11 RECLINER
11 Recliner
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
11.1 Operating Recliner
WARNING
ƽ
ALWAYS make sure that the wheelchair is stable before using the recliner option.
ALWAYS engage both wheel locks while reclining or inclining (sitting up) the wheelchair.
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on this wheelchair (you may order with or
without the seat positioning strap), Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the
wheelchair user. The seat positioning strap is a positioning strap only. It is not designed for use as a safety device withstanding high stress
loads such as auto or aircraft safety belts. If signs of wear appear, strap MUST be replaced IMMEDIATELY.
Ensure the spreader bar is attached and secured before using the Jymni Recliner.
TO HEALTHCARE PROFESSIONALS/ASSISTANTS:
Make sure occupant's hands and body are clear of all pinch points before reclining back. Pinch Points exist between spreader bar and
recliner mechanism. Use caution, otherwise injury may occur.
Keep clear when reclining or inclining chair back to avoid injury.
Make sure the patient is properly positioned in the wheelchair before reclining or inclining (reverse recline) to maintain maximum
stability and safety. Refer to Safety/Handling of Wheelchairs on page 19.
Before using the recliner option, make sure the anti-tipper wheel assemblies are in the lowest adjustment hole (adjustment hole closet to
the ground/floor).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
11 RECLINER
WARNING
Handle
ƽ
When returning the occupant of the wheelchair to the
full upright position, more body strength will be
required for approximately the last twenty degrees of
incline (reverse recline). Make sure to use proper body
mechanics (use your legs) or seek assistance if necessary
to avoid injury.
Release Lever
Upright Position
Wheelchair
3. Adjust the tightness of the headrest/back upholstery. Refer to
Level Surface
4. Make sure wheelchair is occupied and on a level surface before
reclining.
Wheelchair
Reclined Position
6. Inform the occupant of the wheelchair that the wheelchair is about to
be reclined.
7. Make sure occupant's hands and body are clear of all pinch points.
8. Stand behind the wheelchair and grasp both push handles firmly.
9. Squeeze release handles.
10. Slowly pull back on the back assembly while squeezing the release
handles.
Release
Lever
Level Surface
11. When the back reaches the desired angle, slowly let go of the release
handles.
12. To return the back to the full upright position, reverse STEPS 8-11
keeping in mind proper body mechanics.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
11 RECLINER
11.2 Installing/Removing Headrest Extension
Headrest
Extension Tubes
Installing
1. Insert headrest extension tubes into back canes.
2. Position the two headrest extension tubes so that the mounting
holes in the back canes align with the mounting holes in both
headrest extensions and secure with two detent pins.
Mounting Holes
3. Ensure the two detent pins pass completely through the mounting
holes in the two back canes and the headrest extension tubes
Detent Pin
Removing
Detent
Pin
1. Remove the detent pins that secure the headrest extension tubes.
2. Remove the headrest extension tubes.
Back Canes
11.3 Replacing Headrest Pillow
1. Unfasten straps of headrest pillow from behind headrest
upholstery.
Headrest
Fastening
Upholstery
Strips
Strap
2. Secure straps of the new headrest pillow onto fastening strips
located on back of headrest upholstery.
Strap
Headrest Pillow
61
Download from Www.Somanuals.com. All Manuals Search And Download.
11 RECLINER
11.4 Replacing Headrest/Back Upholstery
Headrest Upholstery
Headrest
Upholstery
2. Remove the six mounting screws that secure the headrest
upholstery to the headrest extension tubes.
Headrest
Extension
Tube
Mounting
Screws
3. Secure new headrest upholstery onto headrest extension tubes
with the existing six mounting screws.
Back
Upholstery
Knob
Back Upholstery
1. Unthread one knob on either side of the spreader bar and loosen
the opposite knob.
Mounting
Screws
2. Remove the eight mounting screws that secure the back upholstery
to the back canes.
Back
Cane
3. Secure the new back upholstery to the back canes with the existing
eight mounting screws. Securely tighten.
4. Secure the knob of spreader bar to side frame. Securely tighten
both knobs.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
11 RECLINER
Adjusting Headrest/Back Upholstery Tension
1. Rotate the spreader bar in one of the following directions:
Headrest Upholstery
•
Counterclockwise (away from back upholstery) to loosen
back/headrest upholstery.
Spreader
Bar
•
Clockwise (towards back upholstery) to tighten back/headrest
upholstery.
Back
Upholstery
11.5 Storing/Replacing Spreader Bar
Storing Spreader Bar
The Jymni Recliner is folded for either storage or transporting. One side of the spreader bar MUST be removed and placed in a vertical
position alongside the recliner tube.
Removing From Stored Position
o
1. Rotate the end of the spreader bar 90 toward the opposite side frame.
2. Install threaded end of locking knob into locknut located on the opposite side frame. Securely tighten both knobs.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
11 RECLINER
Placing In Stored Position
1. Remove one locking knob from the spreader bar.
2. Loosen the remaining locking knob on the spreader bar.
3. Rotate detached end of the spreader bar 90° down toward floor.
Locking
Knob
Side Frame
Replacing Spreader Bar
1. Remove both locking knobs that secure the spreader bar to the side
frames.
Spreader
Bar
2. Remove existing spreader bar.
Recliner
Tube
3. Secure new spreader bar to the side frames with the existing locking
knobs. Securely tighten.
Locking Knob
11.6 Adjusting the Seat Width and Depth
WARNING
The seat depth and width directly relates to the
stability of the recliner. Any change may cause the
recliner to decrease in stability. This procedure
MUST be performed by a qualified technician.
ƽ
Spreader Bar
Locking
Knobs
Side Frame
Side Frame
64
Download from Www.Somanuals.com. All Manuals Search And Download.
12 OPTIONS
12 Options
WARNING
ƽ
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or
damage may occur.
The options in this section refer to non-recliner models only. Refer to Recliner on page 59 for 9000XT Recliner options.
12.1 Installing Telescoping I.V. Rod/O Holders
2
For this procedure, refer to FIGURE 1 on page 66.
Installing
WARNING
ƽ
The telescoping I.V. rod/O holder MUST be checked weekly to ensure it is tightly secured to the wheelchair frame. If there is any
looseness whatsoever, tighten the attachment hardware securely before using.
2
Make sure the telescoping I.V. rod is tightly locked before placing I.V. medication on the rod.
The telescoping I.V. rod is designed to support I.V. medication only. DO NOT use it to support objects other than I.V. medication.
The telescoping I.V. rod/O holders clean easily with any household glass type cleaner.
2
1. Slide telescoping I.V. rod/O holder over the step tube of the wheelchair.
2
Mounting bracket of telescoping I.V. rod/O2 holder should be positioned between the two axle mounting positions on wheelchair frame.
2. Secure telescoping I.V. rod/O holder to the wheelchair frame with hex screw, spacer and locknut.
2
3. Telescoping I.V. Rod Holder Only - Secure the top of the telescoping I.V. rod holder to the wheelchair frame with a tie wrap.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
12 OPTIONS
Detail “A” - I.V. Rod/O
Holder
Detail “B” - O holder
2
2
Tie Wrap
Mounting
Bracket
Hex Screw
Telescoping I.V.
Rod Holder
Mounting
Bracket
Hex
Screw
Locknut
Axle Mounting Positions
Step Tube
Spacer
Locknut
Axle Mounting Positions
Spacer
Step Tube
12.2 Cleaning
WARNING
ƽ
The user and O2 cylinder MUST be removed from the wheelchair when cleaning the O2 holder. Otherwise, injury or damage may occur
if cleaning agents come in contact with the O2 regulator.
1. Remove the user, any I.V. medication and the O cylinder from the wheelchair.
2
2. The telescoping I.V. rod/O holders clean easily with any household glass type cleaner.
2
3. After the cleaning solution has dried, it is safe for the user to re-occupy the wheelchair.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
12 OPTIONS
12.3 Installing the 1-inch Forward Rear Wheel Positioner
WARNING
ƽ
DO NOT use the 1-inch forward bracket on recliner wheelchairs OR adjustable angle back wheelchair. Otherwise injury or damage may
occur.
Recliners and Wheelchairs with 1-Inch Forward Rear Wheel Positioner Only: Anti-tippers MUST BE attached at all times.
Spacer
2. Position the right hand 1-inch forward rear wheel positioner onto the
right hand side of the wheelchair frame (FIGURE 2).
Right and left hand sides of the wheelchair are
determined from the users position.
3. Secure the 1-inch forward rear wheel positioner to the wheelchair frame
using the two mounting screws, spacers and locknuts.
Mounting Screw
1-Inch Forward Rear
Wheel Positioner
Locknuts
4. Repeat STEPS 2-3 to Install the left hand 1-inch forward wheel positioner.
Mounting Screw
Spacer
67
Download from Www.Somanuals.com. All Manuals Search And Download.
12 OPTIONS
12.4 Installing/Adjusting Stroller Handles
Removing
Stroller handles shown facing toward the inside of the
wheelchair.
1. Remove the detent pin that secures one stroller handle to one of the
back cane.
2. Remove the stroller handle
3. If necessary, repeat STEPS 1-2 for the opposite stroller handle.
Installing
1. Perform one of the following:
Height Adjustment
Holes
Stroller Handles
•
12-14-Inch Wide Wheelchairs - Insert one of the stroller handles
into one of the back canes so that it is facing either toward or away
from the inside of the wheelchair FIGURE 3.
•
10-Inch Wide Wheelchairs - Insert one stroller handle into one of
the back canes so that it is facing away from the inside of the
wheelchair FIGURE 3.
Detent Pin
2. Position the stroller handle so that the mounting hole in the back cane
aligns with the desired height mounting hole in the stroller handle and
secure with detent pin.
3. Ensure the detent pin passes through the mounting hole in the back cane
and the desired height mounting hole in the stroller handle.
4. Repeat STEPS 1-3 for the opposite stroller handle.
Height Adjustment
1. Remove the detent pin that secures one stroller handle to one of the
back cane.
2. Slide the stroller handle up or down until the desired height is reached,
making sure the mounting hole in the back cane aligns with the desired
height mounting hole in the stroller handle.
3. Reinstall the detent pin so that it passes through the mounting hole in the
back cane AND the desired height mounting hole in the stroller handle.
4. Repeat STEPS 1 - 3 for the opposite stroller handle.
Back Cane
When closing a wheelchair with stroller handles, raise or
lower one of the stroller handles two hole heights.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
12 OPTIONS
12.5 Installing/Removing the Solid Seat Insert
Installing
1. Position the solid seat insert so that it is fully supported by the seat rails and the back edge of the solid seat insert is touching the back canes.
Removing
1. Firmly grasp the solid seat insert and lift it away from the seat upholstery.
12.6 Installing/Removing the Solid Back Insert
Installing
1. Position the solid back insert between the back canes.
2. Wrap the two fastening straps around the back canes. Securely fasten with the two snaps.
Removing
1. Release the two snaps securing the two fastening straps around the back canes and remove the solid back insert.
12.7 Installing the Wheel Lock Extension Handle
Detail “B”
Wheel Lock
Detail “A”
WARNING
ƽ
If the wheelchair is equipped with push to lock wheel
locks, elevating legrests, and wheel lock extension handles,
the wheel lock extension handles MUST be removed
before swinging the elevating legrests to the side,
otherwise injury or damage may result. Interference
between the top of the elevating legrest and the wheel
lock extension handle causes the wheel lock to disengage.
Extension
Handle
Rubber Tip
Wheel Lock
Handle
Wheel Lock
Handle
Wheel Lock
1. Remove the existing rubber tip from the wheel lock handle (Detail “A”).
2. Install the extension handle over the wheel lock handle (Detail “B”).
Wheel Lock
69
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
NOTES
70
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
NOTES
71
Download from Www.Somanuals.com. All Manuals Search And Download.
|