Intellinet Network Solutions Network Router 529930 User Manual

Desktop 10Base-T

Internet ISDN Gateway

User’s Manual

529930

I-ISS-020

Download from Www.Somanuals.com. All Manuals Search And Download.

Package Contents

This package has:

1. One Internet Sharing Station

2. One power adapter

3. Wall Mounting kit

4. This user’s guide

Hardware Introduction

The components of the unit are shown as the following figure:

Front Panel

LED Status Table

ON: DC power is on

PWR

OFF: No DC power

FDX ON: Indicates communication on your LAN is operating at full-duplex mode.

OFF: Indicates transmission mode is half-duplex.

LNK ON: Ethernet interface is being connected.

LAN

OFF: Ethernet interface not connected

ACT Blinking: Indicates traffic passing through the Ethernet port.

OFF: No traffic

ERR ON: Error condition

OFF: Normal condition

UTL (ON=1; OFF=0) Enumerate from left to right.

When the WAN-1 port is connected to modem, and it is on idle state, the LEDs are used to

indicate baudrate. When connection is established, the LEDs are used to indicate utilization.

“000”- Port disconnected

WAN-1

“100”- Baudrate=9.6K; or Utilization=20%

“010”- Baudrate=19.2K

“110”- Baudrate=38.4K; or Utilization=60%

“001”- Baudrate=57.6K

“101”- Baudrate=115.2K

“011”- Baudrate=230.4K

“111”- Baudrate= reserved; or Utilization=100%

ERR ON: Error condition

OFF: Normal condition

UTL (ON=1; OFF=0) Enumerate from left to right.

When the WAN-2 port is connected to modem, and it is on idle state, the LEDs are used to

indicate baudrate. When connection is established, the LEDs are used to indicate utilization.

“000”- Port disconnected

WAN-2

“100”- Baudrate=9.6K; or Utilization=20%

“010”- Baudrate=19.2K

“110”- Baudrate=38.4K; or Utilization=60%

“001”- Baudrate=57.6K

“101”- Baudrate=115.2K

“011”- Baudrate=230.4K

“111”- Baudrate= reserved; or Utilization=100%

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the unit

This unit can be placed on a flat surface or mounted on a metallic surface or partition. Please comply with

the following steps for proper installation.

Desktop Installation

Carefully take out the unit from its packaging

You will find four self-adhesive rubber feet attached on the bottom of the unit, which provide space

for ventilation and cushion the unit needed against vibrations. Place the unit directly on your desk.

Magnetic Mounting Installation

Inside each of the four rubber feet, you will find a magnetic ring. Adhere this unit to steel flat surface

using the magnets on the bottom of the unit.

Wall Mounting Installation

There is a trough on the bottom of the unit, which is used for wall mounting.

Use two screws to mount the mounting track plate onto the wall.

Put the unit over the mounting track plate, and slide it to the suitable position.

Screw

Mounting

Track Plate

Connecting your equipment

Internet

Modem or

ISDN-TA

HUB

Internet Sharing Station

Download from Www.Somanuals.com. All Manuals Search And Download.

1.Connecting the Ethernet cable.

Connect a network cable to the Internet Sharing Station’s RJ-45 or BNC port. This unit supports

two types of Ethernet cables: Thin Ethernet (10BASE2, BNC connector) and Twisted Pair

Ethernet (10BASE-T, RJ-45 connector). During power up, the unit automatically detects the type

of network cable and adjusts to that environment.

Note: Please do NOT use both of BNC and RJ-45 connections simultaneously.

2.Connect your modem.

Connect an external modem or ISDN TA, using a standard serial cable, to the WAN port on the

back of the unit and to a phone line

Notes:

z Turn off the power before connecting or disconnecting modems.

z You can connect up to two modems to the Internet Sharing Station

3.Connect the power adapter.

Connect the power adapter to the units. The Power LED should light.

4.Connect the Internet Sharing Station and all of your PCs to hub

Before proceeding this step, make sure each of your PCs has a network interface card installed.

Configuring the Internet Sharing Station

The easiest way to configure the Internet Sharing Station is to use your existing Web browser. Once you

have set up your PC and installed web browser, you can launch your browser and view web pages from

the Internet Sharing Station.

„

Setting up PC to configure the web

Before using browser to find the web pages from Internet Sharing Station, you have to manually configure

your PC for TCP/IP networking. The DHCP server function of Internet Sharing Station is enabled defaultly,

your PCs should be set to obtain an IP address automatically. This procedure is described in the following

section.

To configure a Windows NT 3.51 system

1. Open the Main group in Program Manager.

2. Open the Control Panel and open the Network icon.

3. Select TCP/IP Protocol within the Installed Network Software Window or install it if necessary. See

your Windows documentation.

4. Click the Configure button and select the Adapter Type.

5. Check the Enable Automatic DHCP Configuration checkbox.

6. Type your computer name in the Host name box. Click OK to close the TCP/IP configuration window.

7. Click OK to close and restart your computer.

To configure a Windows NT 4.0 system

1. Right-click Network Neighborhood and click Properties.

2. Click the Protocols tab and select the TCP/IP Protocol in the list. If TCP/IP does not appear, install it.

See your Windows documentation.

3. Click the Properties button and select the adapter type.

4. Make sure “Obtain an IP Address from A DHCP Server” is selected.

5. Type your computer name in the Host name box.

6. Click OK on the bottom of the TCP/IP window.

7. Click OK to close and restart your computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

To configure a Windows 95/98 system

1. Right-click Network Neighborhood.

2. Click Properties on the pop-up menu.

3. Click the Configuration tab and select the TCP/IP networking component and click Properties.

4. Make sure “Obtain an IP Address Automatically” is selected.

5. Select the DNS Configuration tab, and select Disable DNS.

6. Select the Gateway tab and remove any addresses. Click OK.

7. Click OK to close the Network Control window.

8. Click OK to close and restart your computer.

To configure other systems

See the documentation for your operating system and set the system up for TCP/IP. Configure the system

to be a DHCP client. If the system doesn’t support DHCP, set an IP address that is not conflicted to that

system and in the range from 192.168.0.1 to 192.168.0.252.

Configuring the Internet Sharing Station

After you finish setting up and restart your computer, you can open web browser, type the following in the

Location (or Address) window, and press Enter.

http://192.168.0.254

You should then see the first screen, which will prompt you for a password. Default password is “admin”,

just type admin, then click OK to continue to the configure screen.

Quick Configuration

Simply connect modem to the WAN 1 port of the Internet Sharing Station, and complete all settings on

this first page, then restart the Internet Sharing Station, and then restart all of the PCs, you are ready to

access Internet.

Basic Configuration

Download from Www.Somanuals.com. All Manuals Search And Download.

IP address for the Internet Sharing Station. Use the default value (192.168.0.254)

Address: unless the address is already in use.

Network The default value 255.255.255.0 is OK for small networks.

Mask:

[The

Station]

DHCP

Server:

Primary

DNS:

Select “Enable” to enable the function of DHCP service for local LAN. Select

“Disable” to disable the function of DHCP service

Enter the DNS IP address (default value is 168.95.192.1) provided by your ISP.

Secondar Enter the other DNS IP address provided by your ISP, if possible.

y DNS:

Define the Internet account for the WAN 1 port.

User ID.: Enter the account name provided by your ISP.

Password: Enter the password for the corresponding account name.

[Internet Account]

Phone No.: Enter your ISP’s telephone number. Use the format described in your

modem’s user manual.

IP Address: Enter the IP address assigned to you by your ISP. For dynamic IP

address assignment, the IP address is 0.0.0.0.

Baudrate Assign the data transmission speed on the serial line of WAN 1. Available speeds are

(bps) 9600, 19200, 38400, 57600, 115200, and 230400 bps

Teardown The period of idle time allowed when a connection is established. When timer

Time expired, the connection will be disconnected.

[WAN 1]

Advanced Configurations

Network Configuration

Network Settings:

Download from Www.Somanuals.com. All Manuals Search And Download.

Define Internet accounts for each WAN 1 and WAN 2 ports.

Phone No.: Enter your ISP’s telephone number. Use the format described in your

modem’s user manual.

[Internet Account]

User ID.: Enter the account name provided by your ISP.

Password: Enter the password for the corresponding account name.

IP Address: Enter the IP address assigned to you by your ISP. For dynamic IP

address assignment, the IP address is 0.0.0.0.

Baudrate Assign the data transmission speed on the serial line of WAN 1. Available speeds are

(bps) 9600, 19200, 38400, 57600, 115200, and 230400 bps

Teardown The period of idle time allowed when a connection is established. When timer

Time expired, the connection will be disconnected.

Authentica The allowed password checking protocols in PPP authentication phase.

tion (defaults to select both)

Baudrate Assign the data transmission speed on the serial line of WAN 2. Available speeds are

(bps) 9600, 19200, 38400, 57600, 115200, and 230400 bps

Teardown The period of idle time allowed when a connection is established. When timer

Time expired, the connection will be disconnected.

Authentica The allowed password checking protocols in PPP authentication phase.

Serial Port

[WAN 1]

Serial Port

[WAN 2]

tion

(defaults to select both)

Disable: WAN 2 will always be disabled

Bandwidth-on-Demand (BoD): WAN 2 will be activated only when WAN 1’s

bandwidth is full-load.

Always: WAN 2 will always be activated when the first client accesses the Internet.

RAS-Port: WAN 2 acts as a RAS port that allows user remote dial-in.

Activity

Mode

Modem Configuration

Download from Www.Somanuals.com. All Manuals Search And Download.

Modem AT Command Settings

If your model is listed, simply select it , then the modem initial string will be configured

automatically.

Model:

If your model is not listed, try “Standard” or “Standard 56K” modem

If it still not work, select “Other”. You will have to enter the modem initial strings, as described

below. (You have to refer to modem’s user manual to set these strings)

Initial String: Specifies the command to configure your modem or ISDN TA correctly

Auto-Answe Specifies the command to set the modem or ISDN TA’s auto-answer mode

r String:

Escape

Specifies the code to change modem from data transmission to AT command mode

Seq. Code:

Hang-Up

String:

Specifies the command to hang-up phone call for modem

Specifies the command (sometimes called “Dial Prefix String”) to dial a phone call for modem

or ISDN TA

Dial String:

If your ISP uses a scripting process for logging onto the network before starting a PPP connection, you

can do this with the login script. The login script lets you write a script that automatically logs in and starts

your PPP session as if you had typed the commands. Each line in the script waits for a prompt from the

host computer or sends a response to the host computer.

Enable

Line##

Set “YES” to run script file before PPP takes over; set “NO” to run PPP directly

The login script commands and some examples are described on Appendix A

Download from Www.Somanuals.com. All Manuals Search And Download.

Email Sharing Configuration

The usage of Email sharing allows one Email account shared with multiple users. The [Mail Server

Account] specifies the shared Email account, and the [Local User Account] specify the sharing users. The

detail configurations to some popular Email clients such as “Outlook”, “Eudora”, and “Netscape

Messenger” are described on Appendix B.

Remote Access Service Configuration

Configures WAN 2 as RAS-Port

Internet

pc1

pc2

192.168.0.254

RAS-Port

Internet Sharing Station

192.168.0.1

192.168.0.2

192.168.0.253

Support Network Neighborhood

All allowed dial-in users are defined as E-mail Sharing users as described previous page. In this case, the

allowed users are supervisor, pc1, pc2, pc3, pc4, pc5, pc6, and pc7.

Note that the auto-answer mode should be enabled on the modem that connects to WAN 2, i.e., in the

modem configuration on WAN 2 port, the Auto-Answer-String should be set to “ATS0=x”, where x is a

number which large than or equal to 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

Virtual Server Configuration

Internet Sharing Station

Internet

CHAT Server WWW Server

(192.168.0.10) (192.168.0.1)

FTP Server Telnet Server

(192.168.0.2) (192.168.0.3)

External port on IS020

Any incoming IP packets send to the

external port will redirect to this

internal server on this port

This shows the internal servers that allowed to be accessed through the Internet Sharing Station from

Internet. Type 0.0.0.0 will prevent the Internet users from accessing the internal servers.

Virtual Server settings

FTP Server: Specifies the IP address of the computer that will act as FTP server on your local LAN

Telnet Server: Specifies the IP address of the computer that will act as Telnet server on your local LAN

WWW

Specifies the IP address of the computer that will act as WWW server on your local LAN

Server:

Console Password Configuration

The current password can be changed, the new password will be required for the next time that you want

to configure the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Firmware Upgrade Procedure

You may follow the procedure specified in this page to update your firmware.

Reset to Factory Default

This feature let all configurations return to the initial factory value.

System Restart

If complete all configurations, the new values may effect after you restart the Internet Sharing Station.

Setting up the other PCs

Once the Internet Sharing Station has been configured on your LAN, it is ready for use. However, all of

the PCs must have a network interface card installed, and they must be configured for TCP/IP

networking.

You have to set up all of the PCs on your LAN to be DHCP clients that will obtain an IP address from

Internet Sharing Station automatically. The following describes how to configure your Win95 station to be

a DHCP client. For other operating systems, see Setting up PC to configure web.

1. Right-click Network Neighborhood.

2. Click Properties on the pop-up menu.

3. Click the Configuration tab and select the TCP/IP networking component and click Properties.

4. Make sure “Obtain an IP address automatically” is selected, like the following.

5. Select the DNS Configuration tab, and select Disable, but the fields can be left blank.

6. Select the Gateway tab and remove any addresses. Click OK.

7. Click OK to close the Network Control window.

8. Click OK to close and restart your computer, and you can access Internet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note:

Once the Internet Sharing Station has been configured, all of the PCs should be restarted to get the

new TCP/IP settings from the Internet Sharing Station.

After restarting your computer, please make sure your computer has obtained an IP address, DNS

and Gateway IP address(192.168.0.254).

„

Customizing TCP/IP settings

The Internet Sharing Station is preconfigured for installation on a network that is not set up for TCP/IP. It

uses a range of private IP addresses in a range from 192.168.0.1 to 192.168.0.254, with the address of

the Internet Sharing Station preset to 192.168.0.254.

If you have already set up the TCP/IP protocol on your network, you can customize the Internet Sharing

Station to fit your existing IP policy.

To customize TCP/IP settings for your existing network

1. Configure one of your PCs to be a DHCP client, and restart it, then your PC will obtain an IP address

automatically from Internet Sharing Station.

2. From the selected computer, launch web browser and connect to the Internet Sharing Station web

page (http://192.168.0.254), if the system on your network already have public IP addresses, set

‘DHCP Server:’ to “Disable”, then click “Save” button.

3. Change the Internet Sharing Station’s IP Address to the address that is valid for your network, then

click “Save” button, and then click ‘System Restart’ to restart the Internet Sharing Station.

4. Change the IP address of the selected computer back to its original setting.

5. Make sure the Gateway IP address of all PCs must be same as the Internet Sharing Station’s IP

address, DNS must be enabled, and DNS IP address(es) must be assigned.

Troubleshooting

Troubleshooting gives you solutions to problems that may occur during installation and operation of the

Internet Sharing Station.

1. Problem:

No power to the Internet Sharing Station

Possible Cause: The power adapter is a defective one.

Solution:

Check the power cord and power outlet to verify its connection. If it still remains unlit,

please replaced another power adapter.

2. Problem:

Solution:

Can’t connect to the Internet Sharing Station

1. Check the TCP/IP setup on your PC.

On Windows 95/98: Run winipcfg from Run on the Start menu. The PC should have an

IP address of 192.168.0.n, where n is from 1 to 252. The Gateway IP address of the PC

must be 192.168.0.254. If the IP address is not in the range, click Release then click

Download from Www.Somanuals.com. All Manuals Search And Download.

Renew.

On Windows NT: Type ipconfig from the command prompt. The PC should have an IP

address of 192.168.0.n, where n is from 1 to 252. The Gateway IP address of the PC

must be 192.168.0.254. If the IP address is not in the range, type the following

commands:

ipconfig / release

ipconfig / renew

2. If you have used proxy on the browser, make sure it has 192.168.0.254 as an

exception

In Internet Explorer: Add 192.168.0.254 as an exception

In Netscape Navigator: Add 192.168.0.254 as an exception, mentioned as follow.

3. Problem:

Solution:

Can’t connect to the Internet

1. Check the phone link

Check the phone line. If it’s a regular analog line, connect a telephone and see if you

get a dial tone. Dial your ISP number to see if you get a modem tone.

Is a 9 required for an outside line ?

2. Check the TCP/IP setup on your PC.

On Windows 95/98: Run winipcfg from Run on the Start menu. The PC should have an

IP address of 192.168.0.n, where n is from 1 to 252. The Gateway IP address of the PC

must be 192.168.0.254, and the DNS Server address(es) must not be empty. If the IP

address is not in the range, click Release then click Renew.

On Windows NT: Type ipconfig from the command prompt. The PC should have an IP

address of 192.168.0.n, where n is from 1 to 252. If the IP address is not in the range,

type the following commands:

ipconfig / release

ipconfig / renew

4. Problem:

Solution:

Can not communicate with the ISP.

1. This is mostly likely a problem due to the fact that your baudrate setting is too high for

your modem or ISDN TA. Sometimes the maximum baudrate that your modem or ISDN

TA claims it can achieve is not really attainable because of phone line quality

2. Talk to your ISP to see if the login script is required.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Problem:

Solution:

My Modem/ISDN TA is working fine with my PC running Windows 95. How do I find its

initial string ?

1. Select My Computer, then Dial-Up Networking.

2. Select the icon for your connection, then properties.

3. Click the Configure button, then Connection tab.

4. Select Advanced , then check the option Record a log file, click OK and exit.

5. Use Dial-up Networking to make your on-line connection normally. A log file

MODEMLOG.TXT will be created in your Windows directory.

6. Examine the file to determine the Initial String,

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Standards and Protocols

IEEE 802.3 10BASE-T and 10BASE2

TCP/IP, PPP, CHAP/PAP/MS-CHAP, DHCP

Operational Characteristics

LAN port: 10BASE2/10BASE-T auto sensing

WAN speed:

230.4Kbps max. DTE speed

Power Characteristics

External Power Adapter:

Input Voltage: 100VAC, 60Hz / 120VAC, 60Hz / 230VAC, 50Hz / 240VAC, 50Hz

Output Voltage: 9 VDC, 1 A

Physical Characteristics

Number of ports:

Panel indicators:

1 x 10BASE-T/10BASE2, 2 x RS-232

PWR, Link, Activity, Full Duplex, Error, Utilization/Baudrate

Weight:

Dimensions:

Temperature:

0.28 kg

135 x 104 x 35 mm (L x W x H)

Operating:

0℃ to 40℃;

Storage:

– 20℃ to 70℃

Humidity:

Approvals:

EMI:

5% to 95% (non-condensing)

FCC Class B,VCCI Class B, CISPR 22 Class B

TÜV/GS, UL, cUL

Safety:

Regulatory Standards Compliance

EMI Information

FCC Class B (For USA Only)

FCC ID: NUKISCCM020

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

Warning! This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from the one

which the receiver is connected to

• Consult the dealer or an experienced radio/TV technician for help

You are cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections.

VCCI Class B (For Japan Only)

Download from Www.Somanuals.com. All Manuals Search And Download.

CE Mark Declaration of Conformity for EMC and Safety(EEC)

EMC:

EN55022 (1994)/CISPR 22 (1993)

IEC 1000-4-2 (1995)

class B

4kV CD, 8kV AD

IEC 1000-4-3 (1995)

3V V/m

IEC 1000-4-4 (1995)

1kV - (power line) , 0.5kV - (signal line)

This product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC

Directive 89/336/EEC

Safety Compliance

EN60950, UL 1950

Sicherheitshinweise

1. Die Steckdose muß sich in der Nähe des Gerätes befinden und leicht zugänglich sein.

2. Zum Reinigen den Stecker aus der Steckdose ziehen. Beim Reinigen keine Flüssigreiniger oder

Sprays verwenden, sondern ein angefeuchtetes Tuch.

3. Das gerät nicht in Naßräume oder in der Nähe von Wasser benutzen, wie z.B. Badezimmer,

Schwimmbad, Spülbecken usw. . Das Eindringen von Wasser kann zur Zerstörung des Gerätes

führen.

4. Das gerät nicht auf einer unstabilen Unterlage, wie z.B. Rollwagen, Gestell usw., aufstellen. Es

könnte herunterfallen und Verletzungen oder Beschädigungen von Mensch und Gerät verursachen.

5. Die Belüftungsöffnungen nicht blockieren oder auf falscher Ober-fläche, wie Bett, Sofa usw., stellen.

Durch die Blockierung kann es zur Zerstörung des Gerätes durch Überhitzung kommen.

6. Versuchen Sie niemals dieses Gerät selbst zu warten, da beim Öffnen oder Abnehmen des

Gehäuses die Gefahr eines elektrischen Schlages besteht.

7. Keine Gegenstände auf das Anschlußkabel stellen, damit es nicht durch scharfe Kanten zerstört

werden kann.

8. Keinerlei Gegenstände durch die Öffungen in das Gerät stecken, da es dadurch sonst zu

Kurzschlüssen kommen kann.

9. Bei Störungen des Gerätes den Wartungsdienst verständigen.

10. Bei Reperaturen dürfen nur Orginalersatzteile oder Bauteile mit gleichen Eigenschaften verwendet

werden. Andere Bauteile können Feuer, elektrischen Schlag oder andere Gefahren verursachen.

11. Nach Beendigung von Wartungsarbeiten oder Reperaturen durch den Kundendienst sollte die

Sicherheitsprüfung durchgeführt werden.

12. Bei längerem Stillstand des Gerätes, ist diese von der Versorgungs- spannung zu trennen. Dies

verhindert eine Beschädigung des Gerätes durch eine Überspannung in der Zuleitung.

13. Der arbeitsplatzbezogene Lärmschutzpegel nach DIN 45 635 ist kleiner 70dB (A).

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A: Login Script Files

This section describes the script file commands and syntax to be used when editing script files.

Script file is only required if your ISP does not use a standard PPP negotiation.

„

Learn the script syntax

Five commands can be used to automate a proprietary negotiation process. The commands are as

follows:

send “<string>” Send a data string and then go to next line

wait “<string>” Wait to receive a data string, and then go to next line

send_id

Send user name

send_passwd

hangup

Send password corresponding to the user

Hang Up Modem

run or run_ppp Start to run PPP and ignore rest of script

„

Example of the Login Script File

Scenario

Your ISP instructs you to log in and issue a PPP command. The system prompts for a login and

password. After the ISP’s host sends a welcome message, you enter the “ppp” command. If you

logged in manually with a username of “juns” and a password of “1234”, it would look like this:

Enter username: juns

Enter password: 1234

Welcome to Hinet!

ppp

Script for this scenario

Your script should look like this:

Wait “:”

Send “juns”

Wait “:”

Send “1234”

Wait “!”

Send “ppp”

Run_ppp

Note: You only need to include the last specific character in the text, in this case “!” in “Welcome to

Hinet!”

Script file used for CompuServe

The following is the login script used to log on to CompuServe.

Send

Send “CIS”

Wait “:”

Send_id

Wait “:”

Send_passwd

Wait “!”

Send “GO PPPCONNECT”

Run_ppp

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix B: Configure Your E-mail Clients For E-mail Sharing Function

„

Email Sharing Operation Model

Internet

pc1

192.168.0.254

pc2

Email Server:

Host name: ms25.hinet.net

User name: unextest

Password : xxxxxxxx

E-mail setting on pc1 (or pc2) :

User name: pc1 (or pc2)

Password: xxxx

Incoming POP3 server: 192.168.0.254

Outgoing SMTP server: ms25.hinet.net

Send mail to pc1 :

1. pc1<unextest@ms25.hinet.net>, or

2.”pc1”<unextest@ms25.hinet.net>

In this case, E-mail sharing function allows your ISP E-mail address called unextest@ms25.hinet.net be

shared by PC1 and PC2, so that they can have their own e-mail address, mentioned as follow:

“pc1”<unextest@ms25.hinet.net>

“pc2”<unextest@ms25.hinet.net>

For PC1’s e-mail address

For PC2’s e-mail address

Outlook Express

Step 1: Select Tools->Accounts->Mail

1. Select one account

2. Press “Properties” button

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 3: Fill in the incoming and outgoing mail server

The real mail server

The IP address of Internet Sharing Station

The user name defined in Internet Sharing

Station

The password for this user on Internet Sharing

Station

Netscape Messenger

Step 2: Fill in aliases name and real email address

Select the user name defined in IS020

The shared E-mail account

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 1: Select Edit->Preferences->Mail & Newsgroup->Identity

Select the user name defined in

Internet Sharing Station

The shared E-mail account

Step 2: Fill in the incoming and outgoing mail server

The IP address of

Internet Sharing

Station

The real mail server

The user name defined

in Internet Sharing

Station

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 3: ->Select 192.168.0.254->Edit

Select “POP3 Server” as the

mail receiving protocol

The user name defined in

Internet Sharing Station

Eudora 1.5.4 ~ 3.x.x

Step 1: Select Tools->Options->Getting Started

Select the email account on

Internet Sharing Station

Select the user name defined in

Internet Sharing Station

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 2: Tools->Options->Sending Mail

The shared E-mail account

The real mail server

Eudora 4.x.x and above

Step 1: Select Tools->Options->General

Select the user name defined in

Internet Sharing Station

The shared E-mail account

The IP address of Internet

Sharing Station

Select the user name defined in

Internet Sharing Station

The real mail server

Download from Www.Somanuals.com. All Manuals Search And Download.

IOGear Stereo Receiver GBMH221W6 User Manual
JL Audio Car Speaker SB T TDCMAX 13TW5 User Manual
Kambrook Vacuum Cleaner KBV50 User Manual
Kathrein Satellite TV System UFE 370 S User Manual
King Canada Planer KC 203C User Manual
King Canada Saw KC 712GH 5 User Manual
KitchenAid Blender 9709948A User Manual
KitchenAid Refrigerator KBCS24RSBS00 User Manual
Kole Audio electronic Car Speaker KLE 10 User Manual
Korg Musical Instrument Trinity User Manual