Intel Plumbing Product EE110EM User Manual

Intel Express  
10/100 Stackable Hub  
Fiber and Ethernet Modules  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Start  
1. Turn off the power, then unscrew and remove the panel from an expansion slot on  
the Express 10/100 Stackable Hub.  
Expansion slots: Use either slot. They are  
identical.  
Turn off the power before installing.  
1
2
3
4
5
6
7
8
9
1
0
11  
12  
Green (left)  
Link solid  
=
Activity  
=
blink  
Am  
ber (right)  
rong speed blink  
Disabled solid  
W
=
=
Intel Expr
1
0
/
1
0ub  
Change  
h
0
speed  
Stackable Hu
1
0BASE-T  
1
0
0BASE-  
TX  
Collision  
Managed  
Status  
Power  
2. Plug either the Ethernet Module or the Fiber Module into a slot, using the retaining  
screws to secure the module to the hub.  
Turn on the power after installing.  
1
2
3
4
5
6
7
8
9
1
0
1
1
12  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
=
=
=
blink  
=
Intel Exp
1
0
/
1
0
C
0
hange hubSspeaedckable H
t
1
0BASE-T  
1
0
0BASE-  
TX  
Collision  
Managed  
Status  
C
han  
duple  
ge  
x
A
uto-negotiate  
100  
Ethernet Module  
M
Power  
bps  
10  
M
bps  
C
ha  
nge  
speed  
A
uto  
-negotia  
100  
10  
M
te  
bps  
M
bps  
C
oll  
3. Plug a device in and check the LEDs for a link. You’re done.  
Solid green indicates link. Blinking  
green indicates activity. If you don’t  
get a link, try the other port.  
Ethernet Module  
or  
Auto-negotiate  
100 Mbps  
Change  
duplex  
Auto-negotiate  
Full-duplex  
Change  
speed  
Coll  
The LEDs light for both ports, even  
though you can use only one port at  
a time. This is normal.  
10 Mbps  
Half-duplex  
MDI  
MDI-X  
Solid green indicates link. The Xmt  
LED blinks when data is transmitted.  
The Rcv LED blinks when data is  
received.  
Fiber Module  
Xmt  
Rcv  
Link  
Coll  
Auto-negotiate  
Xmt  
Link  
Change  
duplex  
Full-duplex  
Half-duplex  
TX  
RX  
Rcv  
Coll  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Overview .................................................................................................................................................. 3  
Ethernet Module ....................................................................................................................................... 4  
Bridging 10 and 100 Mbps hubs ....................................................................................................... 4  
Connecting 100 Mbps hubs with TPE cable ..................................................................................... 6  
Connecting to a device at full-duplex ............................................................................................... 7  
Connecting to a 10 Mbps printer from a hub that is operating at 100 Mbps .................................... 8  
Understanding Ethernet Module LEDs ............................................................................................. 9  
Fiber Module .......................................................................................................................................... 12  
Connecting hubs beyond 100 meters .............................................................................................. 12  
Connecting to a device at full-duplex ............................................................................................. 13  
Understanding Fiber Module LEDs ................................................................................................ 15  
Technical Specifications......................................................................................................................... 16  
Limited Hardware Warranty................................................................................................................... 17  
Overview  
This guide covers the Intel Express Stackable Hub Ethernet Module (product code EE110EM) and the  
Intel Express Stackable Hub Fiber Module (product code EE110FX). The Ethernet Module supports  
both the 10BASE-T Ethernet and 100BASE-TX Fast Ethernet standards. The Fiber Module supports  
the 100BASE-FX Fast Ethernet standard.  
The modules can be used only with the 12-port version of the 10/100 Stackable Hub (product code  
EE110TX12). You can install either module in a hub running at 10 or 100 Mbps.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ethernet Module  
Ethernet Module  
or  
Auto-negotiate  
100 Mbps  
Change  
duplex  
Auto-negotiate  
Full-duplex  
Change  
speed  
Coll  
10 Mbps  
Half-duplex  
MDI  
MDI-X  
The Ethernet Module acts as a switch port plugged into an Express  
10/100 Stackable Hub. The Ethernet Module  
bridges Express 10/100 Stackable Hubs running at 10 Mbps to  
hubs running at 100 Mbps.  
connects Express10/100 Stackable Hubs running at 100 Mbps  
to each other with TPE cable (creating separate collisions  
domains).  
connects an Express10/100 Stackable Hub to another device at  
full-duplex, such as a server or switch.  
Bridging 10 and 100 Mbps hubs  
To bridge hubs of different speeds, simply plug an Ethernet Module  
into an expansion slot on a 12-port hub (see “Quick Start” on page 1),  
then connect to a hub running at the other speed. The Ethernet Module  
bridges the two collision domains.  
Express 10/100  
100 Mbps hubs connected  
to 10 Mbps hubs  
Ethernet module  
Stackable Hubs  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
Ethernet Module  
Auto-negotiate  
Auto-negotiate  
Full-duplex  
1
0
0
M
b
p
s
10BASE-T  
Collision  
Managed  
Status  
Power  
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
Hub 1 (100 Mbps)  
Hub 2 (100 Mbps)  
Hub 3 (10 Mbps)  
Hub 4 (10 Mbps)  
=
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Plug the Ethernet Module into  
a 100 Mbps hub—connect it to  
a 10 Mbps hub with CAT 3, 4,  
or 5 TPE.  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Category 3,  
4, or 5 TPE  
Express 10/100  
10 Mbps hubs connected  
to 100 Mbps hubs  
Ethernet module  
Stackable Hubs  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
Ethernet Module  
Auto-negotiate  
Auto-negotiate  
Full-duplex  
1
0
0
M
b
p
s
10BASE-T  
Collision  
Managed  
Status  
Power  
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
Hub 1 (10 Mbps)  
Hub 2 (10 Mbps)  
Hub 3 (100 Mbps)  
Hub 4 (100 Mbps)  
=
=
blink  
=
Intel Express  
Plug the Ethernet Module into  
a 10 Mbps hub—connect it to  
a 100 Mbps hub with CAT 5  
TPE.  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
=
=
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Category 5 TPE only  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Example configurations  
These two example configurations show the combinations of duplex  
and speed LEDs.  
100 Mbps hub connected  
to 10 Mbps hub  
Bridging hubs running at 100 Mbps to hubs at 10 Mbps  
Express 10/100  
Ethernet Module  
Stackable Hubs  
Intel Express  
Auto-negotiate  
10/100 Stackable Hub  
Ethernet Module  
Auto-negotiate  
Full-duplex  
Change  
speed  
Change  
duplex  
Change hub speed  
Auto-negotiate  
Auto-negotiate  
Full-duplex  
1
0
0
M
b
p
s
10BASE-T  
Collision  
Managed  
Status  
Power  
Coll  
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
100 Mbps  
100 Mbps  
10 Mbps  
10 Mbps  
=
100 Mbps  
10 Mbps  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
Half-duplex  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
MDI  
MDI-X  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
This Ethernet Module is plugged into a hub running at 100 Mbps. The  
module is then connected to a 10 Mbps hub by CAT 3, 4, or 5 TPE  
cable.  
Category 3,  
4, or 5 TPE  
10 Mbps hub connected  
to 100 Mbps hub  
Express 10/100  
Bridging hubs running at 10 Mbps to hubs at 100 Mbps  
Ethernet Module  
Stackable Hubs  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
Ethernet Module  
Auto-negotiate  
Auto-negotiate  
Auto-negotiate  
Full-duplex  
1
0
0
M
b
p
s
10BASE-T  
Collision  
Managed  
Status  
Power  
Change  
duplex  
Auto-negotiate  
Full-duplex  
Change  
speed  
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
Coll  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
10 Mbps  
10 Mbps  
100 Mbps  
100 Mbps  
=
=
blink  
=
100 Mbps  
10 Mbps  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Half-duplex  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
MDI  
MDI-X  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
This Ethernet Module is plugged into a hub running at 10 Mbps. The  
module is then connected to a 100 Mbps hub using CAT 5 TPE cable  
only.  
Category 5 TPE only  
Notes on bridging  
1
You can insert the Ethernet Module into a hub running at 10 or  
100 Mbps.  
2
3
4
You don’t need to configure the speed or duplex mode.  
Do not change the duplex mode to full-duplex.  
If you’re using a straight-through TPE cable (standard cable), use  
the MDI port on the Ethernet Module.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting 100 Mbps hubs withTPE  
cable  
Class I hubs, such as the Intel Express 10/100 Stackable Hub, cannot  
be directly connected with TPE cable when running at 100 Mbps.  
However, since the Ethernet Module acts as a switched port on a hub,  
you can use it to connect to another 100 Mbps hub with TPE cable.  
Each hub or hub stack is a separate collision domain.  
Express 10/100  
Stackable Hubs  
Express 10/100  
Stackable Hubs  
NOTE  
Using an Ethernet Module is  
the only way you can connect  
Express 10/100 Stackable  
Hubs to each other with TPE  
cable while operating at 100  
Mbps.  
Intel Express  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10/100 Stackable Hub  
Change hub speed  
Ethernet Module  
Auto-negotiate  
Full-duplex  
Auto-negotiate  
100 Mbps  
10BASE-T  
Collision  
Managed  
Status  
Power  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
=
blink  
=
=
blink  
=
blink  
=
Use Intel Cascade  
Cable to stack hubs.  
=
Use Intel Cascade  
Cable to stack hubs.  
Intel Express  
Intel Express  
10/100 Stackable Hub  
10/100 Stackable Hub  
Change hub speed  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
100BASE-TX  
G
r
e
e
n
(
l
e
f
t
)
G
r
e
e
n
(
l
e
f
t
)
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
Link  
Activity  
Amber (right)  
Wrong speed blink  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
blink  
=
=
=
Collision domain 1  
Collision domain 2  
Category 5 TPE (100 meters max.)  
Because you’re connecting to a hub port, you cannot establish a full-  
duplex connection between the hubs.  
You don’t need to configure the speed or duplex mode of the Ethernet  
Module. Auto-negotiation will work for both settings.  
Notes on connecting hubs running at 100 Mbps  
1
Use only Intel Cascade Cable (product code EE110CC) to stack  
hubs.  
2
Never connect hubs operating at 100 Mbps with TPE cable unless  
you use an Ethernet Module.  
3
4
No configuration of the speed or duplex mode is needed.  
Do not change the duplex mode to full-duplex.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a device at full-duplex  
Express 10/100 Stackable Hubs operate at half-duplex. The only way  
to connect to a device at full-duplex is with an Ethernet Module.  
Connecting to a switch at full-duplex  
Not all device manufacturers implement auto-negotiation of duplex  
mode. To ensure the Ethernet Module connects to the device at full-  
duplex, force the duplex mode to full-duplex.  
To force the duplex mode, use the Change duplex button:  
1
Long press the Change duplex button. The Auto-negotiate LED  
blinks.  
NOTE  
A long press is held for 2  
seconds or more.  
2
3
Short press the Change duplex button. The Full-duplex LED blinks.  
Long press the Change duplex button. The Full-duplex LED stays  
on solid.  
A short press is held for less  
than 2 seconds.  
4
Configure the device on the other end for full duplex. (See the  
device’s documentation for specific instructions.)  
To force the speed, follow the steps above using the Change speed  
button.  
Example configurations  
Connecting to a switch at full-duplex  
Ethernet Module  
or  
Auto-negotiate  
100 Mbps  
Change  
duplex  
Auto-negotiate  
Full-duplex  
Change  
speed  
Coll  
10 Mbps  
Half-duplex  
MDI  
MDI-X  
This is an Ethernet Module plugged into a hub running at 100 Mbps.  
The module is then connected to a 100 Mbps switch using  
CAT 5 TPE cable. The module was forced to run in full-duplex mode.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a server at full-duplex  
Ethernet Module  
or  
Auto-negotiate  
100 Mbps  
Change  
duplex  
Auto-negotiate  
Full-duplex  
Change  
speed  
Coll  
10 Mbps  
Half-duplex  
MDI  
MDI-X  
This is an Ethernet Module plugged into a hub running at 10 or 100  
Mbps. The module is then connected to a server with an Intel  
EtherExpress™ PRO/100 LAN Adapter using CAT 5 TPE cable. Use  
the MDI-X connector on the Ethernet Module.  
You don’t need to configure the Ethernet Module or the LAN adapter  
to establish a full-duplex connection at 100 Mbps. However, if you  
don’t get a full-duplex connection at 100 Mbps, force the speed and  
duplex on both the module and the adapter (see steps 1-4 on page 7).  
Connecting to a 10 Mbps printer from  
a hub that is operating at 100 Mbps  
To connect to a 10 Mbps-only printer through a 10 Mbps hub, use the  
MDI connector on the Ethernet Module. To connect directly to a  
10 Mbps print server, use the MDI-X connector.  
Express 10/100  
Express 10/100  
Ethernet module  
Ethernet module  
Stackable Hub  
Stackable Hub  
Intel Express  
Intel Express  
10/100 Stackable Hub  
Change hub speed  
Ethernet Module  
10/100 Stackable Hub  
Change hub speed  
Ethernet Module  
Auto-negotiate  
Full-duplex  
Auto-negotiate  
Auto-negotiate  
Full-duplex  
Auto-negotiate  
10BASE-T  
Collision  
Managed  
Status  
Power  
1
0
0
M
b
p
s
10BASE-T  
Collision  
Managed  
Status  
Power  
1
0
0
M
b
p
s
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
Half-duplex  
1
0
M
b
p
s
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
(100 Mbps)  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
=
1
2
3
4
5
6
7
8
9
10  
11  
12  
(100 Mbps)  
=
=
=
=
blink  
=
=
blink  
=
10 Mbps hub  
(10 Mbps)  
(10 Mbps)  
Category 3,  
4, or 5 TPE  
Category 3,  
4, or 5 TPE  
Notes on connecting to a device at full-duplex  
1
If you’re unsure of a device’s auto-negotiation capabilities, force  
the duplex mode of the Ethernet Module to ensure you’ll get a full-  
duplex connection.  
2
Your performance with a full-duplex connection will vary  
depending on your network. If you have problems, it’s safest to  
establish a half-duplex connection.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Understanding Ethernet Module LEDs  
The LEDs on the Ethernet Module provide information about the  
module’s configuration and status.  
Ethernet Module  
or  
The LEDs on both  
Auto-negotiate  
100 Mbps  
Change  
duplex  
Auto-negotiate  
Full-duplex  
Change  
speed  
Coll  
ports light when a  
cable is attached  
to either port.  
10 Mbps  
Half-duplex  
MDI  
MDI-X  
Port LEDs  
The LEDs above a port on the Ethernet Module provide information  
about the port’s configuration and status.  
Green LED  
(left side)  
Amber LED  
(right side)  
LED  
Status  
Meaning  
Green  
Solid  
Port has a link.  
Blinking  
Off  
Receive or transmit activity detected on port.  
No link detected.  
Amber  
Steady blink and  
green LED on solid  
Ethernet Module speed and device speed don’t  
match. This occurs only if the speed of the Ethernet  
Module has been forced to either 10 Mbps or  
100 Mbps and the device on the other end doesn’t  
match.  
Blinking and  
green LED off  
The module has auto-partitioned the port due to a  
temporary error condition on the network. Make  
sure the duplex setting on the module matches the  
attached device.  
Off  
Normal. No link detected if green LED is unlit.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Change duplex button and LEDs  
You can determine the Ethernet Module’s duplex configuration and  
status from the duplex LEDs. Use the Change duplex button to cycle  
among duplex modes.  
Attach any Express 10/100 Stackable Hub to the Ethernet Module and  
the module will automatically negotiate the correct duplex setting  
(always half-duplex). The default duplex mode setting is auto-  
negotiate.  
LED  
Status  
Meaning  
Auto-negotiate  
Solid  
Module is set to auto-negotiate the duplex mode.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
half-duplex, and full-duplex.  
Off  
Duplex mode has been forced to half or full-duplex.  
Full-duplex  
Half-duplex  
Solid  
Module is in full-duplex mode.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
half-duplex, and full-duplex.  
Off  
Module is not in full-duplex mode.  
Solid  
Module is in half-duplex mode.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
half-duplex, and full-duplex.  
Off  
Module is not in half-duplex mode.  
To change the duplex mode  
This example forces the duplex mode to full-duplex:  
1
2
3
Long press the Change duplex button. The Auto-negotiate LED  
will blink.  
NOTE  
A long press is held for 2  
seconds or more.  
Short press the Change duplex button. The Full-duplex LED will  
blink.  
A short press is held for less  
than 2 seconds.  
Long press the Change duplex button. The Full-duplex LED will  
stay on solid.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE  
Change speed button and LEDs  
See the 10BASE-T and  
100BASE-TX LEDs on the hub  
to determine the hub speed.  
You can determine the speed of the connection between the Ethernet  
Module and device from the speed LEDs. Use the Change speed button  
to cycle among speed settings.  
Attach any Express 10/100 Stackable Hub to the Ethernet Module and  
the module will automatically negotiate the correct speed. The default  
speed setting is auto-negotiate.  
LED  
Status  
Meaning  
Auto-negotiate  
Solid  
Module is set to auto-negotiate the speed.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
10 Mbps, and 100 Mbps.  
Off  
Speed has been forced to 100 Mbps or 10 Mbps.  
100 Mbps  
10 Mbps  
Solid  
Module is running at 100 Mbps.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
100 Mbps, and 10 Mbps.  
Off  
Module is not running at 100 Mbps.  
Solid  
Module is running at 10 Mbps.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
100 Mbps, and 10 Mbps.  
Off  
Module is not running at 10 Mbps.  
To change the speed  
This example forces the speed to 100 Mbps:  
1
Long press the Change speed button. The Auto-negotiate LED  
blinks.  
NOTE  
A long press is held for 2  
seconds or more.  
2
3
Short press the Change speed button. The 100 Mbps LED blinks.  
A short press is held for less  
than 2 seconds.  
Long press the Change speed button. The 100 Mbps LED stays on  
solid.  
Coll (collision) LED  
The Coll (collision) LED blinks amber when collisions are detected  
and is unlit when no collisions are occurring.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fiber Module  
Fiber Module  
Auto-negotiate  
Full-duplex  
Xmt  
Link  
Change  
duplex  
Half-duplex  
TX  
RX  
Rcv  
Coll  
The Fiber Module acts as a switched port plugged into an Express  
10/100 Stackable Hub. The Fiber Module  
connects an Express 10/100 Stackable Hub running at 100 Mbps to  
another hub or other device beyond the 100 meter limitation (up to  
160 meters at half-duplex or 2 km at full-duplex).  
allows an Express 10/100 Stackable Hub to be connected at full-  
duplex to another device, such as another hub with a Fiber Module  
installed or a switch.  
Connecting hubs beyond 100 meters  
The only way you can connect Express 10/100 Stackable hubs beyond  
the 100 meter limit is with fiber optic cable and a Fiber Module  
plugged into each of the hubs. You can plug the module into a hub  
running at 10 Mbps or 100 Mbps. However, the fiber optic connection  
will always be at 100 Mbps.  
Intel Express  
Fiber Module  
10/100 Stackable Hub  
Auto-negotiate  
Xmt  
Link  
Change hub speed  
Change  
duplex  
Full-duplex  
10BASE-T  
Collision  
Managed  
Status  
Power  
Half-duplex  
100BASE-TX  
Rcv  
5
Coll  
6
TX  
RX  
NOTE  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
7
8
9
10  
11  
12  
=
=
=
blink  
=
At half-duplex, you can con-  
nect hubs up to 160 meters  
apart.  
You don’t need to configure  
the duplex mode if you con-  
nect two Fiber Modules.  
Intel Express  
Fiber Module  
10/100 Stackable Hub  
Change hub speed  
Auto-negotiate  
Xmt  
Link  
Change  
duplex  
Full-duplex  
10BASE-T  
Collision  
Managed  
Status  
Power  
Half-duplex  
100BASE-TX  
Rcv  
5
Coll  
6
TX  
R
Green (left)  
1
2
3
4
7
8
9
10  
11  
12  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
At full-duplex, you can con-  
nect hubs up to 2 km apart.  
Both will auto-negotiate to  
full-duplex mode.  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
=
Amber (right)  
Wrong speed  
Disabled solid  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
=
=
blink  
=
Use 62.5/125-micron multimode fiber optic cable with an SC-type  
connector.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a device at full-duplex  
Not all device manufacturers implement auto-negotiation of duplex  
mode. To ensure the Fiber Module connects to the device at full-  
duplex, force the duplex mode to full-duplex.  
To force the duplex mode, use the Change duplex button:  
NOTE  
1
2
3
4
Long press the Change duplex button. The Auto-negotiate LED  
will blink.  
A long press is held for 2  
seconds or more.  
Short press the Change duplex button. The Full-duplex LED will  
blink.  
A short press is held for less  
than 2 seconds.  
Long press the Change duplex button. The Full-duplex LED will  
stay on solid.  
Configure the device on the other end for full-duplex. (See the  
device’s documentation for specific instructions.)  
Example configurations  
The first example configuration shows the Fiber Module connecting to  
another Express 10/100 Stackable Hub with a Fiber Module installed.  
The second shows the Fiber Module connecting to an Intel Express  
10/100 Fast Ethernet Switch.  
Connecting to another Fiber Module at full-duplex  
Fiber Module  
Auto-negotiate  
Xmt  
Link  
Change  
duplex  
Full-duplex  
Half-duplex  
TX  
RX  
Rcv  
Coll  
This is a Fiber Module plugged into a hub running at either 10 or 100  
Mbps. The module is then connected to another Fiber Module using  
62.5/125-micron fiber optic cable. Both modules auto-negotiated to  
full-duplex by default.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a switch at full-duplex  
Fiber Module  
Auto-negotiate  
Xmt  
Link  
Change  
duplex  
Full-duplex  
Half-duplex  
TX  
RX  
Rcv  
Coll  
This is a Fiber Module plugged into a hub running at either 10 or 100  
Mbps. The module is then connected to an Intel Express 10/100 Fast  
Ethernet Switch at full-duplex using 62.5/125-micron fiber optic cable.  
The module was forced to full-duplex to ensure a connection to the  
switch. The maximum cable distances are shown below.  
Intel Express 10/100 Fast Ethernet Switch  
with two 100BASE-FX modules installed.  
Intel Express 10/100  
Fast Ethernet Switch  
MDI  
MDI-X  
MDI-X  
MDI-X  
MDI-X  
MDI-X  
MDI-X  
MDI-X  
MDI-X  
Console  
9600-N-1  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
Coll/  
Xmt Link Fdpx  
SNMP Power  
Mgmt Fault  
R
c
v
1
0
0
F
l
o
w
Rcv 100 Flow  
2
Rcv 100 Flow  
3
Rcv 100 Flow  
4
Rcv 100 Flow  
5
Rcv 100 Flow  
6
Rcv 100 Flow  
7
Rcv 100 Flow  
t
Port  
Port  
Port  
Port  
Port  
Port  
160 m maximum at  
half duplex.  
2 km maximum at  
full duplex.  
Intel Express  
Fiber Module  
10/100 Stackable Hub  
Auto-negotiate  
Xmt  
Link  
Change hub speed  
Change  
duplex  
Full-duplex  
10BASE-T  
Collision  
Managed  
Status  
Power  
Half-duplex  
100BASE-TX  
Rcv  
Coll  
TX  
RX  
Green (left)  
1
2
3
4
5
6
7
8
9
10  
11  
12  
Link  
Activity  
Amber (right)  
Wrong speed  
Disabled solid  
=
solid  
=
blink  
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
Fiber Module  
Intel Express  
Auto-negotiate  
Xmt  
Link  
10/100 Stackable Hub  
Change  
duplex  
Full-duplex  
Collision  
Managed  
Status  
Power  
Change hub speed  
10BASE-T  
Half-duplex  
100BASE-TX  
10BASE-T  
Collision  
Managed  
Status  
Power  
Rcv  
5
Coll  
6
TX  
7
RX  
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
1
2
3
4
8
9
10  
11  
12  
=
=
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
Amber (right)  
Wrong speed  
Disabled solid  
=
=
blink  
=
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Intel Express  
Change hub speed  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
Green (left)  
Link solid  
Activity blink  
Amber (right)  
Wrong speed  
Disabled solid  
=
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
=
=
blink  
=
=
blink  
=
Intel Express  
10/100 Stackable Hub  
Change hub speed  
10BASE-T  
Collision  
Managed  
Status  
Power  
100BASE-TX  
Green (left)  
Link solid  
Activity blink  
1
2
3
4
5
6
7
8
9
10  
11  
12  
=
=
Amber (right)  
Wrong speed  
Disabled solid  
=
blink  
=
Intel Express 10/100 Stackable Hubs. Each  
stack has a Fiber Module installed.  
Notes on connecting with fiber optic cable  
1
Connect devices up to 160 m apart at half-duplex. Connect up to  
2 km at full-duplex.  
2
Insert the Fiber Module into a hub running at 10 or 100 Mbps.  
However, the connection between the Fiber Module and the  
connected device can only be 100 Mbps.  
3
4
If you’re unsure of a device’s auto-negotiation capabilities, force  
the duplex mode of the Fiber Module to ensure you’ll get a full-  
duplex connection.  
Performance with a full-duplex connection varies depending on  
your network. If you have problems, connect at half-duplex.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Understanding Fiber Module LEDs  
The LEDs on the Fiber Module provide information about the  
module’s configuration and status.  
Fiber Module  
Auto-negotiate  
Xmt  
Link  
Change  
duplex  
Full-duplex  
Half-duplex  
TX  
RX  
Rcv  
Coll  
Duplex LEDs  
You can determine the Fiber Module’s duplex configuration and status  
from the duplex LEDs. Use the Change duplex button to cycle among  
duplex modes.  
LED  
Status  
Meaning  
Auto-negotiate  
Solid  
Module is set to auto-negotiate the duplex mode.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
half-duplex, and full-duplex.  
Off  
Duplex mode has been forced to half or full-duplex.  
Full-duplex  
Half-duplex  
Solid  
Module is in full-duplex mode.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
half-duplex, and full-duplex.  
Off  
Module is not in full-duplex mode.  
Solid  
Module is in half-duplex mode.  
Blinking  
Module is being forced to cycle among auto-negotiate,  
half-duplex, and full-duplex.  
Off  
Module is not in half-duplex mode.  
NOTE  
To change the duplex mode  
A long press is held for 2  
seconds or more.  
This example forces the duplex mode to full-duplex:  
1
Long press the Change duplex button. The Auto-negotiate LED  
blinks.  
A short press is held for less  
than 2 seconds.  
2
3
Short press the Change duplex button. The Full-duplex LED blinks.  
Long press the Change duplex button. The Full-duplex LED stays  
on solid.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Transmit/Receive/Link/Collision LEDs  
LED  
Status  
Meaning  
Xmt (transmit)  
Blinking green  
Off  
Port is transmitting data.  
Port is not transmitting data.  
Rcv (receive)  
Link  
Blinking green  
Off  
Port is receiving data.  
Port is not receiving data.  
Solid green  
Off  
Port has a link.  
No link detected.  
Coll (collision)  
Blinking amber  
Off  
Collisions are detected.  
No collisions are occurring.  
Technical Specifications  
Ethernet Module  
Fiber Module  
Connector: UTP/STP RJ-45 (MDI and MDI-X  
pin configurations)  
Connector: SC fiber optic  
Cable:  
62.5/125µ multimode fiber  
Cable:  
Category 5 unshielded or shielded  
twisted-pair Ethernet (CAT 5 UTP  
or CAT 5 STP) at 100 Mbps.  
optic  
Distance:  
2 km (1.2 miles) at full-duplex  
160 m (525 feet) at half-duplex  
CAT 3, 4, or 5 UTP or STP at  
10 Mbps. This guide abbreviates UTP  
and STP as TPE (twisted-pair Ethernet).  
Standards: 100BASE-FX Fast Ethernet  
Distance:  
100 m (328 feet) between devices  
regardless of speed or duplex mode  
Standards: 10BASE-T Ethernet  
100BASE-TX Fast Ethernet  
Spanning tree: Not supported  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Hardware Warranty  
Intel warrants to the original owner that the hardware product delivered in this package will be free from defects in material  
and workmanship for three (3) years following the latter of: (i) the date of purchase only if you register by returning the  
registration card as indicated thereon with proof of purchase; or (ii) the date of manufacture; or (iii) the registration date if by  
electronic means provided such registration occurs within 30 days from purchase. This warranty does not cover the product if  
it is damaged in the process of being installed. Intel recommends that you have the company from whom you purchased this  
product install the product.  
INTEL RESERVES THE RIGHT TO FILL YOUR ORDER WITH A PRODUCT CONTAINING NEW OR  
REMANUFACTURED COMPONENTS. THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY,  
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF  
NONINFRINGEMENT OF INTELLECTUAL PROPERTY, MERCHANTABILITY, FITNESS FOR A PARTICULAR  
PURPOSE, OR ANY WARRANTY ARISING OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE.  
This warranty does not cover replacement of products damaged by abuse, accident, misuse, neglect, alteration, repair, disaster,  
improper installation or improper testing. If the product is found to be otherwise defective, Intel, at its option, will replace or  
repair the product at no charge except as set forth below, provided that you deliver the product along with a return material  
authorization (RMA) number either to the company from whom you purchased it or to Intel (North America only). If you ship  
the product, you must assume the risk of damage or loss in transit. You must use the original container (or the equivalent) and  
pay the shipping charge. Intel may replace or repair the product with either new or remanufactured product or parts, and the  
returned product becomes Intel’s property. Intel warrants the repaired or replaced product to be free from defects in material  
and workmanship for a period of the greater of: (i) ninety (90) days from the return shipping date; or (ii) the period of time  
remaining on the original three (3) year warranty.  
This warranty gives you specific legal rights and you may have other rights which vary from state to state. All parts or  
components contained in this product are covered by Intel’s limited warranty for this product; the product may contain fully  
tested, recycled parts, warranted as if new. For warranty information call one of the numbers below.  
Returning a Defective Product (RMA)  
Before returning any product, contact an Intel Customer Support Group and obtain an RMA number by calling:  
North America only: (916) 377-7000  
Other locations:  
Return the product to the place of purchase.  
If the Customer Support Group verifies that the product is defective, they will have the Return Material Authorization  
Department issue you an RMA number to place on the outer package of the product. Intel cannot accept any product without  
an RMA number on the package.  
LIMITATION OF LIABILITY AND REMEDIES  
INTEL SHALL HAVE NO LIABILITY FOR ANY INDIRECT OR SPECULATIVE DAMAGES (INCLUDING, WITHOUT  
LIMITING THE FOREGOING, CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES) ARISING FROM THE  
USE OF OR INABILITY TO USE THIS PRODUCT, WHETHER ARISING OUT OF CONTRACT, NEGLIGENCE, TORT,  
OR UNDER ANY WARRANTY, IRRESPECTIVE OF WHETHER INTEL HAS ADVANCE NOTICE OF THE  
POSSIBILITY OF ANY SUCH DAMAGES, INCLUDING, BUT NOT LIMITED TO LOSS OF USE, INFRINGEMENT OF  
INTELLECTUAL PROPERTY, BUSINESS INTERRUPTIONS, AND LOSS OF PROFITS, NOTWITHSTANDING THE  
FOREGOING, INTEL’S TOTAL LIABILITY FOR ALL CLAIMS UNDER THIS AGREEMENT SHALL NOT EXCEED  
THE PRICE PAID FOR THE PRODUCT. THESE LIMITATIONS ON POTENTIAL LIABILITIES WERE AN ESSENTIAL  
ELEMENT IN SETTING THE PRODUCT PRICE. INTEL NEITHER ASSUMES NOR AUTHORIZES ANYONE TO  
ASSUME FOR IT ANY OTHER LIABILITIES.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or  
exclusions may not apply to you.  
Software provided with the hardware product is not covered under the hardware warranty described above. See the applicable  
software license agreement which shipped with the hardware product for details on any software warranty.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Federal Communications Commission (FCC) Statement  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required  
to correct the interference at his own expense.  
The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void  
the user’s authority to operate this equipment.  
Manufacturer Declaration  
This certifies that the Intel Ethernet Module or the Intel Fiber Module complies with the EU Directive 89/33/EEC, using the  
EMC standards EN55022 (Class A) and EN50082-1. This product also meets or exceeds EN 60950 (TUV) requirements. This  
product has been tested and verified to meet CISPR 22 Class A requirements.  
WARNING  
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be  
required to take adequate measures.  
WARNING  
The system is designed to operate in a typical office environment. Choose a site that is:  
·
·
·
·
·
Clean and free of airborne particles (other than normal room dust).  
Well ventilated and away from sources of heat including direct sunlight.  
Away from sources of vibration or physical shock.  
Isolated from strong electromagnetic fields produced by electrical devices.  
In regions that are susceptible to electrical storms, we recommend you plug your system into a surge suppressor and  
disconnect telecommunication lines to your modem during an electrical storm.  
Provided with a properly grounded wall outlet.  
·
Do not attempt to modify or use the supplied AC power cord if it is not the exact type required.  
Ensure that the system is disconnected from its power source and from all telecommunications links, networks, or modems  
lines whenever the chassis cover is to be removed. Do not operate the system with the cover removed.  
AVERTISSEMENT  
Le système a été conçu pour fonctionner dans un cadre de travail normal. L’emplacement choisi doit être:  
·
·
·
·
·
Propre et dépourvu de poussière en suspension (sauf la poussière normale).  
Bien aéré et loin des sources de chaleur, y compris du soleil direct.  
A l’abri des chocs et des sources de ibrations.  
Isolé de forts champs magnétiques géenérés par des appareils électriques.  
Dans les régions sujettes aux orages magnétiques il est recomandé de brancher votre système à un supresseur de  
surtension, et de débrancher toutes les lignes de télécommunications de votre modem durant un orage.  
Muni d’une prise murale correctement mise à la terre.  
·
Ne pas utiliser ni modifier le câble d’alimentation C. A. fourni, s’il ne correspond pas exactement au type requis.  
Assurez vous que le système soit débranché de son alimentation ainsi que de toutes les liaisons de télécomunication, des  
réseaux, et des lignes de modem avant d’enlever le capot. Ne pas utiliser le système quand le capot est enlevé.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNUNG  
Das System wurde für den Betrieb in einer normalen Büroumgebung entwickelt. Der entwickelt. Der Standort sollte:  
·
·
·
·
·
sauber und staubfrei sein (Hausstaub ausgenommen);  
gut gelüftet und keinen Heizquellen ausgesetzt sein (einschließlich direkter Sonneneinstrahlung);  
keinen Erschütterungen ausgesetzt sein;  
keine starken, von elektrischen Geräten erzeugten elektromagnetischen Felder aufweisen;  
in Regionen, in denen elektrische Stürme auftreten, mit einem Überspannungsschutzgerät verbunden sein; während eines  
elektrischen Sturms sollte keine Verbindung der Telekommunikationsleitungen mit dem Modem bestehen;  
mit einer geerdeten Wechselstromsteckdose ausgerüstet sein.  
·
Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu verwenden, wenn es sich nicht um genau den erforderlichen  
Typ handelt.  
Das System darf weder an eine Stromquelle angeschlossen sein noch eine Verbindung mit einer  
Telekommunikationseinrichtung, einem Netzwerk oder einer Modem-Leitung haben, wenn die Gehäuseabdeckung entfernt  
wird. Nehmen Sie das System nicht ohne die Abdeckung in Betrieb.  
AVVERTENZA  
Il sistema è progettato per funzionare in un ambiente di lavoro tipico. Scegliere una postazione che sia:  
·
·
·
·
·
Pulita e libera da particelle in sospensione (a parte la normale polvere presente nell’ambiente).  
Ben ventilata e lontana da fonti di calore, compresa la luce solare diretta.  
Al riparo da urti e lontana da fonti divibrazione.  
Isolata dai forti campi magnetici prodotti da dispositivi elettrici.  
In aree soggette a temporali, è consigliabile collegare il sistema ad un limitatore di corrente. In caso di temporali,  
scollegare le linee di comunicazione dal modem.  
·
Dotata di una presa a muro correttamente installata.  
Non modificare o utilizzare il cavo di alimentazione in c. a. fornito dal produttore, se non corrisponde esattamente al tipo  
richiesto.  
Prima di rimuovere il coperchio del telaio, assicurarsi che il sistema sia scollegato dall’alimentazione, da tutti i collegamenti di  
comunicazione, reti o linee di modem. Non avviare il sistema senza aver prima messo a posto il coperchio.  
ADVERTENCIAS  
El sistema está diseñado para funcionar en un entorno de trabajo normal. Escoja un lugar:  
·
·
·
·
·
Limpio y libre de partículas en suspensión (salvo el polvo normal)  
Bien ventilado y alejado de fuentes de calor, incluida la luz solar directa.  
Alejado de fuentes de vibración.  
Aislado de campos electromagnéticos fuertes producidos por dispositivos eléctricos.  
En regiones con frecuentes tormentas eléctricas, se recomienda conectar su sistema a un eliminador de sobrevoltage y  
desconectar el módem de las líneas de telecomunicación durante las tormentas.  
Previsto de una toma de tierra correctamente instalada.  
·
No intente modificar ni usar el cable de alimentación de corriente alterna, si no se corresponde exactamente con el tipo  
requerido.  
Asegúrese de que cada vez que se quite la cubierta del chasis, el sistema haya sido desconectado de la red de alimentación y  
de todos lo enlaces de telecomunicaciones, de red y de líneas de módem. No ponga en funcionamiento el sistema mientras la  
cubierta esté quitada.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Intel Automated Customer Support  
You can reach Intel’s automated support services 24 hours a day, every day at no charge. The services contain  
the most up-to-date information about Intel products. You can access installation instructions, troubleshooting  
information, and general product information.  
World Wide Web & Internet FTP  
Access Intel’s World Wide Web home page  
or download information using  
anonymous FTP.  
Intel BBS  
Use Intel’s Bulletin Board. Dial in by  
modem at 8-N-1, and up to 14.4 Kbps.  
Troubleshooting  
Software updates  
Installation notes  
Product information  
How to access:  
WWW  
US and Canada  
Europe  
1-503-264-7999  
+44-1793-432955  
+1-503-264-7999  
News: news://cs.intel.com  
FTP  
Host: ftp.intel.com  
Directory: /support  
Intel Customer Support Technicians  
Free support for 90 days: You can speak with our technical support professionals free of charge for 90 days  
after your initial call.  
Other support services: You can purchase a range of support services, including 24 hour support, per incident  
support, on-site service, and software and hardware maintenance agreements. For details about the Intel  
Support Service options, download document 8549 from one of the automated services.  
Worldwide access: Intel has technical support centers worldwide. Many of the centers are staffed by techni-  
cians who speak the local languages. For a list of all Intel support centers, the telephone numbers, and the  
times they are open, download document 9089 from one of the automated services.  
If you don’t have access to automated services, contact your local dealer or distributor.  
Or call +1-916-377-7000 from 07:00 to 17:00 Monday through Friday, U.S. Pacific Time.  
03/31/97  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Indesit Washer Dryer IWDC 6143 User Manual
IOGear Switch GUH274W3 User Manual
JVC Security Camera TK C2201UA User Manual
Kenmore Refrigerator 106511800 User Manual
Kenwood Marine Radio TM 261A User Manual
KitchenAid Microwave Oven W10189714A User Manual
KitchenAid Ventilation Hood W10331007B User Manual
Kodak Scanner A 61003 User Manual
Konftel Printer G510 7276 00 User Manual
Konica Minolta Printer 832HG User Manual