™
Intel EtherExpress PRO/100
LAN+Modem56 PC Card
User’s Guide
How to Use This Manual
This User’s Guide contains the latest information on the EtherExpress
PRO/100 LAN+Modem56 PC Card available at press time. It is designed
to help both new and experienced users with installation and configura-
tion.
Installation and Configuration Overview
For an overview, see the Quick Installation Card. For complete technical
details and troubleshooting information, see the chapter covering your
operating system (Chapter 2 Windows 95, Chapter 3 Windows NT, or
Chapter 4 Windows 3.x/MS-DOS) in this User’s Guide.
How to Find More Information
Use the Table of Contents, Index, and page and text headings in this User’s
Guide to help you find what you need. Check the README file on Disk 2,
Network Drivers disk. To check for updated drivers, visit our Customer
Support web site at:
http://support.intel.com
See Appendix A for additional support information.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Hardware Installation ..................................... 1-1
Software Supplied ................................................................... 1-2
Hardware Installation .............................................................. 1-3
Unpacking and Inspection ....................................................... 1-3
Other Required Equipment ..................................................... 1-4
Installing Card and Cables ...................................................... 1-5
PRO/100 Modem and Ethernet Connections.......................... 1-6
Windows* 95 Installation ............................... 2-1
Which Version of Windows 95? ............................................... 2-1
How Can I Tell Which Version I Have? .................................... 2-1
Additional Information in this Chapter ..................................... 2-2
Windows 95 Installation (Retail Version) ................................. 2-2
Windows 95 OSR2 Installation
(OEM Version) .................................................................. 2-4
How to Install for Windows 95 and NetWare* ......................... 2-8
Utilities..................................................................................... 2-8
Power-Saving Modes .............................................................. 2-9
Windows 95 Troubleshooting .................................................. 2-9
Troubleshooting Checklist ..................................................... 2-10
Windows 95 Driver Parameters Reference ........................... 2-13
Windows NT Installation................................ 3-1
Which Version of Windows NT? .............................................. 3-1
How Can I Tell Which Version and Service Pack I Have? ....... 3-2
Additional Information in this Chapter ..................................... 3-2
Windows NT 4.0 Installation.................................................... 3-3
Windows NT 3.51 Installation.................................................. 3-5
Power-Saving Modes .............................................................. 3-7
Utilities..................................................................................... 3-7
Windows NT Driver Parameters Reference ............................ 3-8
Windows 3.x/DOS Installation....................... 4-1
Installation under MS-DOS ..................................................... 4-2
Windows 3.x Modem Driver Settings .................................... 4-36
Windows 3.x Network Driver Parameters ............................. 4-37
ODI Settings (for M16BODI.COM) ........................................ 4-38
Error Messages for Windows 3.x and MS-DOS Drivers ....... 4-47
Download from Www.Somanuals.com. All Manuals Search And Download.
iv PRO/100 LAN+Modem PC Card User's Guide
Windows 3.x Troubleshooting................................................ 4-51
Computer-Specific Application Notes (Windows 3.x)............ 4-60
Utilities and Applications .............................. 5-1
Utilities..................................................................................... 5-1
Country Identifier Utility........................................................... 5-1
Modem Test Utility ................................................................... 5-2
Diagnostic Test Utility (M16BTEST.EXE) ................................ 5-3
COM port monitor (Windows 3.x only) .................................... 5-5
Communications Application Notes and Modem
Script Files ...................................................................... 5-6
Modem Reference .......................................... 6-1
Result Codes........................................................................... 6-1
AT Command Reference ......................................................... 6-4
S-Register Reference............................................................ 6-25
Automated Customer Support ..................... A-1
Specifications ................................................ B-1
Limited Warranty ........................................... C-1
Agency Notices ............................................. D-1
Software License Agreement ........................E-1
Index .........................................................Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Hardware Installation
Introduction
The PRO/100 PC Card is the ideal high-speed, multifunction solution for
portable PC users. It supports 10 and 100Mbps Ethernet networks and
modem speeds up to 56Kbps for high-performance connectivity in any
environment. The PRO/100 PC Card plugs into your computer’s Type II
PC Card slot for simultaneous connection to an Ethernet LAN and the
telephone network.
56K Technology
The PRO/100 PC Card uses K56flex* modem technology to reach speeds
up to 56Kbps. K56flex Technology enables notebook users to access
information and E-mail on corporate networks, the Internet and other
online services at speeds up to 56Kbps over standard phone lines.
These higher speeds are achieved by avoiding conversion from digital to
analog lines in the connection between the user and service provider.
Ordinary connections begin over an analog line, are converted to digital
by the phone company and are converted back to analog in the final
segment before arriving at the service provider. In order to achieve 56K
connections, there can only be one digital to analog conversion. This
requires the service provider to have a direct digital connection and
therefore, avoids one conversion of the signal. By avoiding this conver-
sion, data download speeds up to 56K are possible. Data sent upstream by
the user travels at the standard V.34 rate. Also, the modems at both ends
of the call must be compatible to achieve speeds up to 56K. If the
modems at both ends of the call are not compatible, they will negotiate a
standard V.34 connection.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2 PRO/100 LAN+Modem PC Card User’s Guide
With K56flex technology, current country-specific regulations may limit
download speeds. Additional factors such as phone line conditions, can
affect the performance of the PRO/100 PC Card. You can find more
detailed technical information on K56flex performance on Intel's support
web site, support.intel.com.
Model
MBLA1656
Combination card that provides access to
10Base-T and 100Base-TX networks and
modem speeds up to 56Kbps. An Ethernet
Adapter Cable (RJ-45) and Modem Cable
(RJ-11) are supplied. It provides access to
both 10Mbps and 100Mbps networks with a
single Ethernet Adapter Cable, and auto-
senses 10Mbps or 100Mbps network speed.
Requires Category 5 (data grade)
unshielded twisted pair (UTP) cabling
for 100Mbps network connections.
Software Supplied
Intel drivers and other software are supplied on 3.5-inch 1.44 megabyte
disks. All popular network operating systems, including NetWare, Win-
dows 95, Windows NT, Windows 3.x, and Windows for Workgroups are
supported.
An easy-to-use Installation Program for Windows 3.x is provided on the
Intel Installation Disk, which includes the country identifier utility for local
modem settings.
Additional Features
The PRO/100 PC Card is a Type II PC Card conforming to the Personal
Computer Memory Card International Association (PCMCIA) PC Card
Standard. It supports HotSwap, suspend/resume power management, full-
duplex transmission at 10Mbps, and Advanced Look-Ahead Pipelining.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation 1-3
HotSwap
This card supports HotSwap on a PC Card computer that is running
Microsoft Windows 95 or Windows 3.x/MS-DOS using Card and Socket
Services. This feature allows the PRO/100 PC Card to be removed from
the computer, temporarily replaced with another type of PC card, then
reinserted without loss of the local area network connection.
Power Management Suspend/Resume
Power management features such as suspend/resume are supported by the
PRO/100 PC Card on PCMCIA systems running Windows 95 or Win-
dows NT, or Windows 3.x/MS-DOS using Card and Socket Services. This
means that when the computer enters a reduced power or power saving
mode, an ongoing local area network connection will remain active for the
period of time allowed by the network operating system
Hardware Installation
Note
Hardware installation requirements may vary with different
operating systems. For example, if your system is configured for
automatic detection of the card (for example, under Windows
95), the computer should be ON and standard operating
software loaded when the card is inserted. For installation
instructions specific to your particular environment, see the
appropriate chapter: Chapter 2. Installation with Windows 95,
Chapter 3. Installation with Windows NT, and Chapter 4.
Installation with Windows 3.x/MS-DOS.
The PRO/100 PC Card is compatible with Type II PC Card slots. The
hardware installation procedures outlined here are typical. Installation and
removal procedures vary on different PC Card-capable computers and
under different operating systems.
Unpacking and Inspection
After opening the PRO/100 PC Card box, verify that all parts are included
and have not been damaged during transportation. Retain the packing
materials.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4 PRO/100 LAN+Modem PC Card User’s Guide
Package Contents
• EtherExpress™ PRO/100 LAN+Modem PC Card PC Card (Model
MBLA1656)
• Model MBLA-1656: Ethernet adapter cable with a 15-pin PC Card
connector at one end and female RJ-45 connector at the other for
10Base-T or 100Base-TX connectivity
• Modem cable with RJ-11 telephone connector
• Intel EtherExpress™ PRO/100 LAN+Modem PC Card User's
Guide
(this book)
• Intel EtherExpress™ PRO/100 LAN+Modem PC Card Quick
Start card
• Software on two 1.44 MB 3.5-inch diskettes
• Protective adapter case
• 6-foot telephone cable
• Product registration card
Other Required Equipment
1 For LAN operations: a local area network supporting 10 or
100Mbps Ethernet, as required, and a network operating system
supported by the PRO/100 PC Card.
Note
Since the PRO/100 PC Card automatically detects the speed of
the network to which it is connected, it may be safely connected
to either a 100Base-TX or 10Base-T network, as specified in
items 2 and 3 below.
2 For connection to a 100Base-TX Ethernet network, a Category 5
(data grade) unshielded twisted pair (UTP) network cable terminat-
ing in a male RJ-45 connector and connected to a 100Mbps hub or
switch.
3 For connection to a 10Base-T Ethernet network, a network cable
terminating in a male RJ-45 connector and connected to a 10Mbps
hub or switch.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation 1-5
4 For modem operations: an analog telephone line or PABX
connection (RJ-11), and if needed, an RJ-11 adapter for the local
telephone system.
Note
Do not connect to a digital telephone line or digital PABX
system. The hardware on the adapter will protect your modem
from inadvertent connection to a digital line.
Installing Card and Cables
Inserting the PRO/100 PC Card into the PC Card Slot
1 Grasp the PRO/100 PC Card by the edges with the Intel logo
facing upward and the 68-pin PC Card connector next to the card
slot.
2 Insert the card into the PC card slot and push it in until it is firmly
seated. If you have more than one PC card slot, the PRO/100 PC
Card will automatically detect which slot it is in.
Inserting the PRO/100 PC Card into the Computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-6 PRO/100 LAN+Modem PC Card User’s Guide
Note
The PRO/100 PC Card may feel hot to the touch, after
prolonged periods of normal use in some environments. This is
normal and is not known to affect operation of the Intel card,
the host computer, or any other peripheral device. However, to
avoid discomfort, use caution when removing the card from your
computer after extended use (see your computer manual for
removal procedures).
PRO/100 Modem and Ethernet Connections
Connecting the Modem Cable to the PRO/100
• Hold the PC Card with the top (card label and network graphic)
facing you. Grasp the flat connector on the end of the Modem
Cable with the network graphic on top, and plug it in to the
matching receptacle on the right side of the PRO/100 PC Card.
The cable connector will click into place. Do not force the connec-
tion.
MODEM CABLE
Attaching the Modem Cable to the PRO/100.
Connecting the Modem Cable to the Telephone Line
• Plug one end of a male analog telephone line cable into the RJ-11
jack on the Modem Cable, and the other end into an analog (single-
line) RJ-11 telephone wall jack.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation 1-7
Caution
The PRO/100 PC Card will not work with digital telephone lines
or digital PABX systems. The adapter hardware will protect your
modem against damage from inadvertent connection to a digital
line.
TRANSMIT/RECEIVE
(YELLOW)
CARRIER
DETECT
(GREEN)
TELEPHONE
CABLE
MODEM CABLE
Connecting the Telephone Cable to the Modem Cable.
Connecting the Ethernet Adapter Cable to the PRO/100
• Hold the PC Card with the top facing upward. Grasp the flat
connector on the end of the Ethernet Adapter Cable with the
network graphic on top, and plug it in to the matching receptacle on
the left side of the PRO/100 PC Card. The cable connector will
click into place. Do not force the connection.
ETHERNET
ADAPTER CABLE
PC-3808
Attaching the Ethernet Adapter Cable to the PRO/100.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-8 PRO/100 LAN+Modem PC Card User’s Guide
Connecting to a Twisted Pair network.
Caution
For safety reasons, do not interchange the telephone (RJ-11) and
Ethernet (RJ-45) cables by forcing the Ethernet cable into the
modem sloton the PRO/100 PC Card.
• Plug the male RJ-45 connector at the end of the network cable into
the female RJ-45 connector on the Ethernet Adapter Cable.
LAN ACTIVITY
(YELLOW)
LINK INTEGRITY
Orange = 100 Mbps
Green = 10 Mbps
RJ-45 TWISTED PAIR ETHERNET CONNECTOR
Connecting the Ethernet Adapter Cable to the Network.
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Windows 95 Installation
Which Version of Windows 95?
Two Versions and Two Installation Paths
Currently two versions of Windows 95 are available:
• The standard retail version (designated 4.00.950 or 4.00.950a)
• OEM Service Release Version 2 (designated 4.00.950b, also known
as OSR2)
Installation procedures are presented in two separate sections:
• Windows 95 Installation (Retail Version)
• Windows 95 OSR2 Installation (OEM Version)
How Can I Tell Which Version I Have?
1 In Windows 95, click Start, Settings, and Control Panel.
2 In Control Panel, double-click the System icon.
3 In the System Properties window, click the General tab (if not
already displayed) and view information under System.
• For Microsoft Windows 95 4.00.950 or 4.00.950a, follow the
installation instructions under the heading Windows 95 Installation
(Retail Version)
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2 PRO/100 LAN+Modem PC Card User’s Guide
• For Microsoft Windows 95 4.00.950b, follow the installation
instructions under the heading Windows 95 OSR2 Installation
(OEM Version)
Additional Information in this Chapter
This chapter also contains the following Windows 95 information:
• How to Install for Windows 95 and NetWare
• Power Saving Modes
• Utilities
• Troubleshooting
• Driver Parameters Reference
Windows 95 Installation (Retail Version)
Overview
Installation under the standard retail version of Windows 95 should be a
“plug and play” operation: Windows 95 should recognize the Intel card
when it is inserted and prompt for the Intel software disk. The Intel files
will be copied to the hard drive and the computer will restart. The country
identifier utility will launch automatically.
Important Notes
Please note the following important information before starting the install
process.
• The usual path for Windows 95 files installed on your hard drive is
C:\WINDOWS\OPTIONS\CABS. The “CAB” files are com-
pressed versions of the Windows 95 distribution files. Organization
of the CD-ROM version of these files mirrors the diskette version:
If prompted to insert the disk labeled "Windows 95 Disk 1" the
corresponding CD-ROM file and path would be
"c:\windows\options\cabs\disk1.cab".
• All the Intel files required for Windows 95 installation can be found
on Intel Disk 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-3
• Windows 95 troubleshooting information is provided in this chapter
following the installation sections.
Recommended Installation Steps
Insertion, Detection, and Prompt for Disk
1 With the computer powered-up and Windows 95 running, insert the
PRO/100 PC Card into the PC Card slot in the computer. Windows
95 will detect the insertion of the adapter. (If it does not, see item 3
of the Troubleshooting Checklist: Be sure that PCMCIA support is
enabled ... later in this chapter.)
2 At the New Hardware Found screen specifying Intel EtherExpress
PRO/100 LAN+Modem PC Card, select Driver from disk provided
by hardware manufacturer and click OK.
3 At the Install From Disk screen, insert Intel Disk 1, Installation
Disk and verify the specified path (for example: A:\). Click OK.
4 Intel files will be copied from the Intel disk and Windows 95 will
recognize the modem and network functionality of the Intel adapter.
Windows 95 Network Installation
In most cases Windows 95 network files will need to be installed, using
CAB files from diskette or CD-ROM. If another PC Card modem or
network adapter was installed previously on your system, some of these
files may already be present.
5 If prompted for Windows 95 networking files, click OK at the
Insert Disk screen.
6 At the Copying Files screen, specify the path to Windows 95
installation files (usually c:\windows\options\cabs) and click OK.
7 At the System Settings Change screen, remove the Intel disk from
the disk drive and click Yes. If Windows 95 networking was
installed, the computer will restart.
Country Identifier Utility
8 After the computer restarts and Windows 95 reloads, the country
identifier utility will be launched automatically. At the country
DiodwennltoiafiderfroumtilWitywwsc.Sreoemna,nmuaalks.ecotmhe. Aalpl MpraonpurailastSeesaerlcehctAiondnDaonwdnclooamd.plete
2-4 PRO/100 LAN+Modem PC Card User’s Guide
the program. (For details on this utility, see Chapter 5. Utilities and
Applications.)
Windows 95 OSR2 Installation
(OEM Version)
Overview
Installation under the OSR2 version of Windows 95 should be performed
using the Update Device Driver Wizard, as described below. Windows 95
will recognize the Intel card when it is inserted and display the Update
Device Driver Wizard window. Intel and Windows files will be located or
copied as required and the computer will restart. The Intel country
identifier utility will launch automatically.
Important Notes
Please note the following important information before starting the install
process.
• You may be prompted more than once for Intel or Windows 95
files, due to limitations in OSR2.
• The usual path for Windows 95 files installed on your hard drive is
C:\WINDOWS\OPTIONS\CABS. The "CAB" files are com-
pressed versions of the Windows 95 distribution files. Organization
of the CD-ROM version of these files mirrors the diskette version:
If prompted to insert the disk labeled "Windows 95 Disk 1" the
corresponding CD-ROM would typically be
c:\windows\options\cabs\disk1.cab.
• All the Intel files required for Windows 95 OSR2 installation can be
found on Intel Disk 1.
• Windows 95 troubleshooting information is provided in this chapter
following the installation sections.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-5
Recommended Installation Steps
Insertion, Detection, and Prompt for Disk
1 With the computer powered-up and Windows 95 running, insert the
PRO/100 PC Card into the PC card slot in the computer.
2 Windows 95 will detect the Intel adapter and then display the
following Update Device Driver Wizard screen (if the adapter is not
detected, see Troubleshooting Item 3: “Be sure that PCMCIA
support is enabled ...” under Windows 95 Troubleshooting later in
this chapter).
3 Insert Intel Disk 1. Click Next>.
4 On the Update Device Driver Wizard screen click Finish.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-6 PRO/100 LAN+Modem PC Card User’s Guide
Copying Intel Files
5 At the Insert Disk screen, click
6 At the Copying Files... screen, specify A:\ in the Copy files from:
box and click
Copying Windows 95 Network Files
In most cases Windows 95 network files will need to be installed, using
CAB files from diskette or CD-ROM. If another PC Card modem or
network adapter was installed previously on your system, some of these
files may already be present.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-7
7 Windows 95 will detect new hardware and copy files. At the Insert
Disk screen, click OK.
8 At the Copying Files... screen, specify the path to the Windows 95
files (usually c:\windows\options\cabs) in the Copy files from: box
and click OK.
9 At the System Settings Change screen, remove the Intel disk from
the disk drive and click Yes. The computer will restart.
Country Identifier Utility
10 After the computer restarts and Windows 95 reloads, the country
identifier utility will launch automatically. At the country identifier
utility screen make the appropriate selection and complete the
program. (For details on this utility, see Chapter 5. Utilities and
Applications.)
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8 PRO/100 LAN+Modem PC Card User’s Guide
How to Install for Windows 95 and NetWare
1 Install the PRO/100 PC Card driver and verify the installation as
described above in the installation procedures.
2 In the Control Panel, double-click the Network icon.
3 From the Configuration tab in the Network window, click Add.
4 From the Select Network Component Type window, select Client
and click Add.
5 Under Manufacturers in the Select Network Client window, select
Microsoft.
6 In the Network Clients window, select Client for NetWare Net-
works.
7 Click OK (you will be returned to the Network window).
8 From the Configuration tab in the Network window, click Add.
9 From the Select Network Component Type window, select Protocol
and click Add.
10 Select Microsoft as the manufacturer and IPX/SPX-compatible
Protocol under Network Protocols, then click OK to return to the
Network window.
11 Click OK to close the Network window, then restart the computer
when prompted.
Utilities
Several utilities are provided with the PRO/100 PC Card that run under
Microsoft Windows or MS-DOS. The utilities are:
• Country Identifier Utility (Windows 95, NT, 3.x)
• Modem Test (Windows 95, NT, 3.x)
• Diagnostic Test (MS-DOS prompt required)
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-9
These utilities are automatically copied to your hard drive during installa-
tion under Windows 95, and icons for the utilities are installed in a
Windows program group at the time of installation. See Chapter 5.
Utilities and Applications for additional information.
Power-Saving Modes
The PRO/100 PC Card has two power-saving modes to reduce adapter
power consumption under certain conditions: Network-only mode and
Modem-only mode (Network & Modem is the default).
Network-only mode disables the modem function on the adapter. This
mode should only be used when the modem will not be needed. Modem-
only mode disables the network function on the adapter. It should only be
used when the network will not be needed. When the Intel adapter is set
to either Network-only or Modem-only mode, it remains in that mode
until re-configured to a different mode.
To specify a power-saving mode under Windows 95, select Network from
Control Panel, select the Configuration tab, select Intel EtherExpress
PRO/100 LAN+Modem PC Card and click Properties, select the
Advanced tab, and select a mode in the Function(s) property (Network &
Modem is the default).
Windows 95 Troubleshooting
Quick Troubleshooting (Device Conflicts)
1 To review the adapter configuration, right-click the My Computer
icon and select Properties.
2 Select the Device Manager tab.
3 Proceed according to your version of Windows 95 (see the begin-
ning of this chapter for information):
• For Windows 95 (Retail Version), expand the item Multifunction
Adapters.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-10 PRO/100 LAN+Modem PC Card User’s Guide
• For Windows 95 OSR2 (OEM Version), expand the item
Modem.
4 For either version, select Intel EtherExpress PRO/100
LAN+Modem PC Card (Multi-function Parent Device) and click
Properties.
5 From the Properties window, select the Resources tab.
6 Confirm that there are no conflicts with other installed devices.
Troubleshooting Checklist
The following section suggests troubleshooting steps to follow when the
Intel PC Card adapter is not automatically detected or not correctly
identified. These conditions are generally resolved by one or more of the
measures below. Detailed instructions for each measure follow.
1 Be sure you have the latest firmware and driver.
2 Run the Intel diagnostic utility M16BTEST.
3 Be sure PCMCIA support is enabled in Windows 95.
4 Create C:\WINDOWS\MODEMLOG.TXT to help resolve issues
with the modem.
5 Check other sources for updated troubleshooting information.
Note
When these directions or Windows 95 prompts you to shut down
or restart the computer, select Start, Shut Down, Shut down the
computer? Leave the computer turned off for a few seconds, and
then turn it back on. Do not press CTRL+ALT+DEL or use
your computer’s reset button to restart your computer--this can
lead to device malfunctions. On some machines, all hardware is
not reset unless power is cycled.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-11
1 Be sure you have the latest firmware and
driver.
To determine what firmware and driver version you have, click My
Computer, Control Panel, Modems, highlight the Intel EtherExpress™
PRO 100 LAN+Modem PC Card (Modem), click Diagnostics, click the
Port the Intel modem is using, click More Info. The firmware information
for the adapter should display.
To find out what the latest versions are, and to download updated
versions if necessary, access the Intel BBS or web site (see the Intel
Automated Customer Support information toward the end of this guide).
2 Run the Intel diagnostic utility
M16BTEST.
To verify correct operation of the PRO/100 PC Card, run the Intel
diagnostic test utility provided on Disk 2, Network Drivers Disk. Follow
the steps below.
1 Shut down Windows 95 and power the machine off.
2 Restart Windows 95. Press the F8 key when the message Starting
Windows 95 appears on the screen. Choose Safe Mode Command
Prompt Only from the Startup menu (or press Shift+F5 to go
directly to the command prompt).
3 Run M16BTEST.EXE at the MS-DOS prompt. (See Chapter 5.
Utilities and Applications for more detailed instructions.)
4 If your Intel PC Card does not test properly, try the same procedure
on another computer. If the card still does not work, contact Intel
Customer Support.
3 Be sure that PCMCIA support is enabled
in Windows 95.
In some cases, Windows 95 PCMCIA support may not have been installed
or enabled during an upgrade or installation, due to previous machine
configurations or options selected during installation. If this Windows 95
support is not enabled, run the PCMCIA Wizard by double-clicking on
Download from Www.Somanuals.com. All Manuals Search And Download.
2-12 PRO/100 LAN+Modem PC Card User’s Guide
the PCMCIA icon in the Control Panel, so that Windows 95 will automati-
cally detect the type of PCMCIA controller in the machine.
4 Create C:\WINDOWS\MODEMLOG.TXT
to record the status of the modem.
Double-click My Computer, Control Panel, Modems, highlight the Intel
EtherExpress PRO 100 LAN+Modem PC Card (Modem), click Proper-
ties, Connection, Advanced, check the box Record a log file, remove any
modem strings in the box Extra settings, then click OK. If you try to dial
again and get disconnected, the file C:\WINDOWS\MODEMLOG.TXT
will be created. Review the information in that file with Intel Customer
Support.
5 Check other sources for updated
troubleshooting information.
The following information may also be helpful:
1 Review the HARDWARE.TXT file in the Windows 95 directory.
This file is written by Microsoft and describes machine specific
problems when the software was released.
2 Review the README.TXT file by clicking on the README icon
in the Program Group (or read from Intel Disk 1, Installation Disk).
This file will contain information about the driver that may not have
been available when this user manual was published.
3 Use the Intel BBS or website for updated troubleshooting informa-
tion for Windows 95. See Appendix A. Intel Automated Customer
Support, for access information.
4 Contact your computer vendor for updated information.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-13
Windows 95 Driver Parameters Reference
Caution
Under most circumstances it will not be necessary to make
modifications directly to the registry. Incorrect settings can
result in undesirable changes to the configuration of Windows
95. Consult Intel Customer Support for assistance if you find it
necessary to modify the registry.
M16B.SYS (NDIS 3) Settings for Microsoft Windows 95
M16B.SYS is an NDIS 3 LAN adapter. It conforms to the Microsoft
Network Driver Interface Specification (NDIS). It supports both Win-
dows NT and Windows 95.
Windows 95 Support
The M16B.SYS driver also supports the networking environment in
Microsoft Windows 95.
The files necessary for using M16B.SYS with Windows 95 include:
NETM16B.INF
Intel network installation file for Win-
dows 95
M16B.SYS
Intel NDIS 3 driver for Windows 95
Intel modem installation file
MDMM16B.INF
MFM16B.INF
Intel multifunction installation file
Download from Www.Somanuals.com. All Manuals Search And Download.
2-14 PRO/100 LAN+Modem PC Card User’s Guide
There are user-configurable parameters for the M16B.SYS driver that can
be modified using the Network Control Panel applet built into Windows
95. This applet queries the user for parameter selections and then sets the
corresponding parameters in the registry. The user-configurable param-
eters are as follows:
Parameter
Default Valid Values
Registry Value
DIRECT ENABLE
EARLY TRANSMIT
OFF
ON
OFF, ON
OFF
0
0
1
0
1
ON
FULL DUPLEX
FUNCTION(S)
OFF
OFF
ON
NETWORK&MODEM
NETWORK&MODEM
0
1
2
0
1
2
0
1
0
1
NETWORK ONLY
MODEM ONLY
LINE SPEED
AUTO AUTO DETECT
10MBPS
100MBPS
LINK INTEGRITY
MODE
ON
I/O
OFF
ON
I/O
MEMORY MAPPED
NETWORKADDRESS
TRANSMITBUFFERSIZE
7168
1024-29696
1024-29696
The network node address can be modified by specifying a value for
‘NetworkAddress’ such as ‘00A0C9112233’. If the user does NOT specify
a ‘NetworkAddress’ then the M16B.SYS driver uses the network node
address contained in the PRO/100 Card information structure.
There are parameters in the Windows 95 registry which specify the
configuration of the EtherExpress™ PRO/100 LAN+Modem PC Card
hardware to the M16B.SYS driver. Many of these parameters correspond
directly to the user-configurable parameters. These parameters are found
in the registry at the following location:
HKEY_LOCAL_MACHINE\SYSTEM\CURRENTCONTROLSET\SERVICES\CLASS\NET\000X
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 95 Installation 2-15
Caution
Under most circumstances it will not be necessary to make
modifications directly to the registry. Incorrect settings can
result in undesirable changes to the configuration of Windows
95 or NT.
The registry parameters are as follows:
Keyword
Default
Valid Values
DEVICEVXDS
DEVLOADER
DIRECTENABLE
DRIVERDESC
M16B.SYS
NDIS
0
0-1
INTEL ETHEREXPRESS PRO/100
LAN+MODEM PC CARD (NETWORK)
EARLYTRANSMIT
ENUMPROPPAGES
FULLDUPLEX
1
0-1
NETDI.DLL,ENUMPROPPAGES
0
0-1
0-2
FUNCTIONENABLE
INFPATH
0
NETM16B.INF
INTERRUPTNUMBER
IOBASEADDRESS
LINESPEED
04 00 00 00
02 00 00 00
0
1
0-2
0-1
LINKINTEGRITY
MEMORYBASEADDRESS 01 00 00 00
MODE
0
0-1
NETWORKADDRESS
PLATFORMTYPE
TRANSMITBUFFERSIZE
1
1
11264
1024-29696
‘InterruptNumber’, ‘IoBaseAddress’, and ‘MemoryBaseAddress’ are NOT
user-configurable and their values are assigned by the Windows 95
Configuration Manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-16 PRO/100 LAN+Modem PC Card User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
Windows NT Installation
Which Version of Windows NT?
Two Versions and Two Installation Paths
Installation of the PRO/100 PC Card is different for versions 4.0 and 3.51
of Windows NT. Before starting the installation you must know what
version of Windows NT you have. If you’re using version 3.51, you must
also know the version of any software Service Pack installed.
Currently two versions of Windows NT are supported:
• Windows NT Version 4.0
• Windows NT Version 3.51 (including Service Packs)
Installation procedures are presented in two separate sections:
• Windows NT 4.0 Installation
• Windows NT 3.51 Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2 PRO/100 LAN+Modem PC Card User’s Guide
How Can I Tell Which Version and Service
Pack I Have?
• If you don't know what version you have, follow the steps below.
• If you know you have Version 4.0, skip to the Windows NT 4.0
Installation section. No additional version information is required.
• If you know you have Version 3.51, follow the steps below to
determine what Service Pack version is installed. This information is
required in step 9 of the Windows NT 3.51 Installation section.
To obtain version and Service Pack information, proceed as follows:
1 Open the Windows NT Diagnostics application in the Administra-
tive Tools folder. The Administrative Tools folder can be found in
the Program Manager window (Windows NT 3.51 interface) or by
selecting Start and Programs (Windows NT 4.0 interface).
2 In the Diagnostics application, version information can be found
either by selecting the Version tab or by clicking the OS Version ...
button.
3 If the version is 3.51, be sure to note the value of the Service Pack
field:
• For Windows NT Version 3.51 with Service Pack 5 or greater,
follow step 9a in the installation instructions for Windows NT
3.51.
• For all other versions of Windows NT 3.51, follow step 9b in the
installation instructions for Windows NT 3.51.
Additional Information in this Chapter
This chapter also contains the following information:
• Power Saving Modes
• Utilities
• Driver Parameters Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows NT Installation 3-3
Windows NT 4.0 Installation
Installing the PRO/100 PC Card under Windows NT 4.0 requires
installing the network driver and the modem separately. The network
driver must be installed first.
PCMCIA Services Verification
Before installing the Intel adapter, make sure that PCMCIA services are
enabled on your computer.
1 Select Devices from the Control Panel.
2 Scroll down the Device list to the PCMCIA device. The Status
should be Started and the Startup should be Boot. If this is not how
PCMCIA is configured, then click Startup and set the Startup Type
to Boot and click OK.
Network Driver Installation
Use the following procedure to install the network driver:
3 Shutdown the computer and turn off the power.
4 Insert the PRO/100 PC Card into the PC Card slot in the com-
puter.
5 Power-up the computer.
6 Select Network from the Control Panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4 PRO/100 LAN+Modem PC Card User’s Guide
7 Select the Adapters tab and click Add.
8 On the Select Network Adapters screen, click Have Disk. Insert
Intel Disk 1, Installation Disk and make sure the specified path is
correct, for example: A:\. Click OK.
9 Select Intel EtherExpress PRO/100 LAN+Modem PC Card and
click OK.
10 At the PRO/100 PC Card Setup screen, choose appropriate
settings. Click OK.
11 At the Network screen click Close.
12 At the Network Settings Change screen, remove the Intel disk from
the disk drive and click Yes. The computer will shut down and
restart.
Modem Setup
After the computer has been restarted, use the following procedure to
install the modem:
13 Select Modems from the Control Panel.
14 At the Install New Modem screen make sure that the "Don’t detect
my modem; I will select it from a list" checkbox is NOT checked.
Click Next. NT will query the COM ports looking for the Intel
modem. It should find the Intel modem as shown below. Click
Next>.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows NT Installation 3-5
15 The country identifier utility will be autmatically launched. At the
country identifier utility screen, make the appropriate country
selection.
16 At the Install New Modem screen click Finish.
17 At the Modems Properties screen click Dialing Properties... to set
up dialing properties (not necessary if a modem had been previously
installed). Click Close.
Windows NT 3.51 Installation
PCMCIA Services Verification
Before installing the Intel adapter, make sure that PCMCIA services are
enabled on your computer.
1 Select Devices from the Control Panel.
2 Scroll down the Device list to the PCMCIA device. The Status
should be Started and the Startup should be Boot. If this is not how
PCMCIA is configured, then click Startup and set the Startup Type
to Boot and click OK.
Network Driver Installation and Modem Setup
3 Shutdown the computer turn off the power.
4 Insert the PRO/100 PC Card into the PC Card slot in the com-
puter.
5 Power-up the computer.
6 Select Network from the Control Panel.
7 At the Network Settings screen click Add Adapter....
8 In the Network Adapter Card: pull-down box select <Other>
Requires disk from manufacturer and click Continue.
9 Insert Intel Disk 1, Installation Disk and make sure the specified
path is correct (see below), according to the Service Pack version
installed (see the version detection section earlier in the chapter if
you don't know what Service Pack version you have).
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6 PRO/100 LAN+Modem PC Card User’s Guide
9a For Windows NT 3.51 with Service Pack 5 or greater, specify:
\A:
9b For all other versions of Windows NT 3.51 specify:
A:\NT351.
Click OK.
10 Select Intel EtherExpress PRO/100 LAN+Modem PC Card and
click OK.
11 At the PRO/100 PC Card Setup screen, choose appropriate
settings. Click OK.
12 The Network Settings screen should show Intel EtherExpress
PRO/100 LAN+Modem PC Card under Installed Adapter Cards.
Click OK.
13 At the Network Settings Change screen, remove the Intel disk from
the disk drive and click Yes. The computer will be shutdown and
restarted.
14 To install the country identifier utility under any version of Win-
dows NT 3.51, run the Intel Installation Program from Intel Disk 1,
Installation Disk. Use the Program Manager File/Run sequence.
Type A:\SETUP in the Command Line box, and click OK. The
country identifier utility will be copied to your hard drive and an
icon installed in the Startup Group and Intel Mobile Program
Group. The program can be run by clicking on the appropriate icon,
or it will load automatically the next time the computer is restarted.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows NT Installation 3-7
Power-Saving Modes
The PRO/100 PC Card has two power-saving modes to reduce adapter
power consumption under certain conditions: Network-only mode and
Modem-only mode.
Network-only mode disables the modem function on the PRO/100. This
mode should only be used when the modem will not be needed. Modem-
only mode disables the network function on the PRO/100. It should only
be used when the network will not be needed. When the adapter is set for
either mode, it remains in that mode until re-configured to a different
mode.
To specify a power-saving mode under Windows NT 4.0, select Network
from Control Panel, select the Adapters tab, select the Intel EtherExpress
PRO/100 LAN+Modem PC Card, click Properties, and select a mode in
Power-Saving Options/Function(s) (Network & Modem is the default).
Under Windows NT 3.51, select Network from Control Panel, select the
Intel EtherExpress PRO/100 LAN+Modem PC Card, click Configure,
and select a mode in Power-Saving Options/Functons(s).
Utilities
Several utilities are provided with the PRO/100 PC Card that run under
Microsoft Windows or MS-DOS:
• Country Identifier utility (Windows 95, NT, 3.x)
• Modem test (Windows 95, NT, 3.x)
• Diagnostic test (MS-DOS)
These utilities are automatically copied to your hard drive and launched
during installation under Windows NT version 4.0 or version 3.51 with
Service Pack 5 or greater. For pre-Service Pack 5 versions of NT 3.51, run
the Intel Installation Program from Intel Disk 1, Installation Disk, after
installing Windows NT version 3.51. Icons for these utilities are also
installed in the Windows program group at the time of installation. See
Chapter 5. Utilities and Applications for additional information.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-8 PRO/100 LAN+Modem PC Card User’s Guide
Windows NT Driver Parameters Reference
M16B.SYS (NDIS 3) Settings for Microsoft Windows NT
M16B.SYS is an NDIS 3 network interface card (NIC) driver. It conforms
to the Microsoft Network Driver Interface Specification (NDIS). It
supports both Windows NT and Windows 95.
Caution
Under most circumstances it will not be necessary to make
modifications directly to the registry. Incorrect settings can
result in undesirable changes to the configuration of Windows
95 or NT. The M16B.SYS driver supports the networking
environment in Microsoft Windows NT versions 3.51 and
greater.
The files necessary for using M16B.SYS include:
For Windows NT 4.0
M16B.DLL
Intel PRO/100 installation DLL
OEMSETNT.INF Intel installation file for Windows NT
MDMM16B.INF Modem support file for Windows NT 4.0
M16B.SYS
Intel NDIS 3 driver for Windows NT
For Windows NT 3.51
M16B.DLL
Intel PRO/100 installation DLL
OEMSETNT.INF Intel installation file for Windows NT
MODEM.IN_
M16B.SYS
Compressed modem support file for
Windows NT 3.51
Intel NDIS 3 driver for Windows NT
There are user-configurable parameters to the M16B.SYS driver which can
be modified using the Network Control Panel built into Windows NT.
This applet uses the OEMSETNT.INF file to set the corresponding
parameters in the registry. The user-configurable parameters are as
follows:
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows NT Installation 3-9
Parameter
Default
Valid Values Registry Value
DIRECT ENABLE
DISABLED
DISABLED
0
ENABLED
1
EARLY TRANSMIT
FULL DUPLEX
FUNCTION(S)
ENABLED
DISABLED
NETWORK
DISABLED
0
ENABLED
1
DISABLED
0
ENABLED
1
NETWORK & MODEM
NETWORK ONLY
MODEM ONLY
0
1
2
INTERRUPT
5
3, 4, 5, 7,
10, 11, 15
SAME
I/O PORT
0X320
0X2E8
0X200-0X3D0
SAME
I/O PORT
3F8,2F8,3E8,2E8
SAME
LINE SPEED
AUTO DETECT AUTO DETECT
0
10MBPS
1
100MBPS
2
LINK INTEGRITY
ENABLED
DISABLED
0
ENABLED
1
MEMORY ADDRESS 0XD4000
MODE I/O
0XA0000 - 0XFE000
I/O
SAME
0
1
MEMORY MAPPED
The network node address can be modified by manually editing the
registry and adding the parameter ‘NetworkAddress’ with a hexadecimal
string value, such as ‘00A0C7112233’. If the user does NOT specify a
‘NetworkAddress’ then the M16B.SYS driver uses the network node
address contained in the PRO/100 PC Card information structure.
There are parameters in the Windows NT registry which specify the
configuration of the PRO/100 PC Card hardware to the M16B.SYS
driver. Many of these parameters correspond directly to the user-
configurable parameters. These parameters are found in the registry at the
following location:
HKEY_LOCAL_MACHINE\SYSTEM\CURRENTCONTROLSET\SERVICES\M16B1\PARAMETERS\
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10 PRO/100 LAN+Modem PC Card User’s Guide
The registry parameters are as follows:
Keyword
Default
Valid Values
BUSNUMBER
0
BUSTYPE
0X1
DIRECTENABLE
EARLYTRANSMIT
FULLDUPLEX
0
0-1
0X1
0
0-1
0-1
FUNCTIONENABLE
INTERRUPTNUMBER
IOBASEADDRESS
IOBASEADDRESS_1
IOLENGTH
0
0-2
0X5
0X2E8
0X320
0X07
0XF
0
3,4,5,7,8,9,A,B,F
3F8,2F8,3E8,2E8
0X200 - 0X3D0
IOLENGTH_1
LINESPEED
0-2
0-1
LINKINTEGRITY
MEMORYMAPPEDBASEADDRESS
MEMORYMAPPEDSIZE
MODE
0X1
0XD6000 A2000-FF000
0X1000
0
0-1
0-1
MODEMFUNCTION
NETWORKADDRESS
0X01
PCCARDATTRIBUTEMEMORYADDRESS 0XD4000 A0000 - FE000
PCCARDATTRIBUTEMEMORYOFFSET 0XF000
PCCARDATTRIBUTEMEMORYSIZE
PCCARDMEMORYWINDOWOFFSET
PCMCIA
0X2000
0
1
0
0-1
0-1
PLATFORMTYPE
TRANSMITBUFFERSIZE
0X1C00 0X0400-0X1E800
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
Windows 3.x/DOS Installation
This chapter contains comprehensive information on how to install and
configure the PRO/100 PC Card for systems running Microsoft Windows
3.x and MS-DOS. The topics covered are:
• Installation under MS-DOS
• Installation under Windows 3.x
• Windows 3.x Network Operating System Alphabetical Reference
• Windows 3.x Modem Configuration Notes
• Windows 3.x Network Driver Parameters
• Error Messages for Windows and Windows 3.x/DOS Drivers
• Windows 3.x Troubleshooting
• Computer-Specific Application Notes (Windows 3.x)
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2 PRO/100 LAN+Modem PC Card User’s Guide
Installation under MS-DOS
For systems running MS-DOS without Windows, see “Manual Installa-
tion” in the “Alphabetical Reference” section later in this chapter.
Installation under Windows 3.x (including
Windows for Workgroups)
Run the Intel Installation Program if you are using Windows 3.1 or
Windows for Workgroups 3.11. Proceed as follows:
1 With Windows running, insert Disk 1, Installation Disk, into your
disk drive.
2 From the Program Manager, choose File, then Run. In the Com-
mand Line box, type the following:
A:SETUP
3 Press Enter or click OK.
4 Select your network operating system from the list displayed and
click OK.
5 Follow the on-screen instructions. Note the following variations for
NetWare and other network operating systems:
Novell NetWare Installation
With Novell NetWare highlighted, click the OK button. Intel
provides all software necessary to configure your NetWare client
workstation. Upon completion, the Installation Program will reboot
your system. When your system comes back up, log in to the
network.
Note
The NetWare VLM shell is used to connect to your NetWare
server. The Intel Installation Program will decompress and
configure the necessary files. If you do not plan to use the
Installation Program, see “Manual Installation” in the
“Alphabetical Reference” later in this chapter for instructions on
how to decompress and load the NetWare VLM files.
If you need NETX shell support, contact your System Adminis-
trator.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-3
Installation of Other Network Operating Systems
For listed network operating systems other than Novell NetWare,
highlight your network operating system and click the OK button.
6 Once you have completed the steps prompted by the Intel Installa-
tion Program, exit the program and find your network operating
system in this chapter of the User’s Guide, using the “Alphabetical
Reference.” Follow the procedures indicated there to complete the
installation.
The Installation Program will modify your AUTOEXEC.BAT,
CONFIG.SYS, and network configuration files to match the
optimum configuration for your system.
Completing the Installation
Use the instructions in the next section “Windows 3.x Network Operating
System Alphabetical Reference” under the following circumstances:
• To complete the installation of network drivers under Windows 3.x
after you have run the Intel Installation Program. Find your network
operating system in the alphabetical listing and follow the steps
there.
• To install network drivers manually under a network operating
system not supported by the Intel Installation Program. See the
instructions under “Generic Installation” or “Manual Installation” in
the “Windows 3.x Network Operating System Alphabetical Refer-
ence.”
Windows 3.x Network Operating System
Alphabetical Reference
This section is organized in alphabetical order by network operating
system vendor or topic. Unless otherwise indicated, these instructions are
designed to be used with the Intel Installation Program. They assume a
first-time installation of client software on a workstation, using the
configuration values set by the Intel Installation Program or, when the
Installation Program is not used, using the default values listed in “Win-
dows 3.x Network Driver Parameters Reference” later in this chapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4 PRO/100 LAN+Modem PC Card User’s Guide
The PRO/100 PC Card supports ODI, NDIS (version 2.01) and packet
drivers under Windows 3.x. To determine which of these drivers you need
for your networking environment, consult your network administrator or
network documentation.
Artisoft LANtastic version 6.0
NDIS 2.0 Driver
1 Run the Intel Installation Program from the Installation Disk.
2 Choose Artisoft LANtastic from the Select Network Operating
System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Run the Artisoft LANtastic 6.0 “install” program. Specify
C:\LANTASTI as the destination directory (or the drivers directory
as specified in the Intel Installation Program).
5 At the “Select network adapter” screen, choose “NDIS Support for
Network Adapters.”
6 When prompted for the “manufacturer’s driver disk” on the “Enter
NDIS driver directory” screen, insert the Intel Network Drivers
Disk.
7 Complete the Artisoft installation.
8 Reboot the computer and start LANtastic.
AT&T StarGROUP LAN Manager version
2.1a
NDIS 2.0 Driver
See Microsoft LAN Manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-5
Banyan VINES version 5.5
NDIS 2.0 Driver
Prior to installing the Banyan Vines client software, it is necessary to
determine the Interrupt Number for the PRO/100 PC Card. After you
have installed the Adapter, follow these steps to determine the Interrupt
Number:
1 Insert Intel Disk 2, Network Drivers Disk in the floppy drive.
2 At the DOS prompt, enter
M16BTEST.EXE
3 Press Enter.
4 When the Main Menu opens, run Test.
The IRQ number will be displayed when the Test is complete.
5 Write down the IRQ number to use when you proceed with the
installation.
For example, if the IRQ=6, write down the number 6.
Now continue with the Banyan Vines installation as follows:
1 In Windows 3.x run the Intel Installation Program from Intel Disk
1. Installation Disk, as described at the beginning of this chapter.
2 Choose Banyan VINES from the Select Network Operating System
screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion. The Installation Program also creates a \VINES directory on
your hard disk.
4 Copy the files from the VINES Master disk into the VINES
directory.
5 Copy the PROTOCOL.INI file from the \NDIS directory on Intel
Disk 2. Network Drivers Disk into the VINES directory.
6 Change to the VINES directory.
7 Type PCCONFIG and select Network Card Settings, followed by
NDIS Ethernet.
8 Enter the IRQ value you wrote down in step 5 of the M16BTEST
procedure described above.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-6 PRO/100 LAN+Modem PC Card User’s Guide
9 At the PROTOCOL.INI bindings prompt, type INTELNET.
10 Press F10 to save and Esc to return to the main menu.
11 Select Login Environment Settings, followed by Default Communi-
cations Driver, followed by NDIS Ethernet.
12 Press Esc to return to the Main Menu and press F10 to save.
13 Manually add these lines to your AUTOEXEC.BAT file:
CD\VINES
BAN
DEC PATHWORKS versions 5.x or 6.x
NDIS 2.0 Driver
These instructions are based on PATHWORKS documentation for
configuration of a PC as a client workstation, using a system service
already installed on a LAN Manager server and the LAN Manager SETUP
diskette.
Prior to installing the DEC PATHWORKS client software, it is necessary
to determine the Interrupt Number for the PRO/100 PC Card. After you
have installed the PRO/100 PC Card, follow these steps to determine the
Interrupt Number:
1 Insert the Intel Network Drivers Disk in the floppy drive.
2 At the DOS prompt, enter
M16BTEST.EXE
3 Press Enter.
4 When the Main Menu opens, run Test.
The IRQ number will be displayed when the Test is complete.
5 Write down the IRQ number to use when you proceed with the
installation.
For example, if the IRQ=6, write down the number 6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-7
Now continue with the DEC PATHWORKS installation as follows:
1 In Windows 3.x run the Intel Installation Program from Intel Disk
1. Installation Disk, as described at the beginning of this chapter.
2 Choose DEC PATHWORKS from the Select Network Operating
System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Check the README file on your PATHWORKS SETUP disk for
requirements such as lastdrive, setver, etc. You will need 500 K of
free conventional memory and about 1 MB of extended memory to
run PATHWORKS SETUP. Be sure you have a lastdrive statement
in your CONFIG.SYS file (lastdrive=g will work in most cases).
5 Use a text editor to modify the file A:\NDIS\PI.TPL on the
PATHWORKS SETUP disk, as follows (A:\NDIS is a hidden
directory. You can access it by typing CD A:\NDIS):
Change the line
;NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]
to read
NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]
The NI_IRQ value must be the same as the interrupt value you will
use for the Intel adapter.
6 Run the SETUP program from the PATHWORKS SETUP disk for
LAN Manager.
7a For Pathworks 5.0, choose Configure PC.
7b For Pathworks 6.0, select Yes for the “Has the Pathworks software
been installed to a LAN Manager file Service.”
8 In the Select Drive Window, choose “Network.”
9 Select DECnet as transport.
10 When prompted to choose a network adapter, choose “Other.”
11 When prompted for driver information, in the “Other Adapter”
window use the following:
a. for PATHWORKS 5.0:
NDIS DRIVER PATH: A:\
Download from Www.Somanuals.com. All Manuals Search And Download.
4-8 PRO/100 LAN+Modem PC Card User’s Guide
NDIS DRIVER FILE: M16BNDIS.EXE
NDIS DRIVER NAME: INTEL$
b. for PATHWORKS 5.1:
DRIVER FILE: A:\M16BNDIS.EXE
PROTOCOL.INI STUB: A:\DEC\PROTOCOL.INI
c. for PATHWORKS 6.0:
DRIVER FILE: A:\M16BNDIS.EXE
PROTOCOL.INI STUB: A:\DEC\PROTOCOL.INI
Skip the Additional Files section.
12 Insert Intel Disk 2, Network Drivers Disk when prompted.
13 Enter your node information when prompted.
14 Save the PROTOCOL.INI file with the default settings.
At this point, the SETUP program will try to connect to the
DECnet server. Once connected, the SETUP program will map a
logical drive to your system service.
15 Highlight the logical drive mapped by the SETUP program, and
press Enter to run PWSETUP.
16 Press Enter to confirm the Software Destination C:\PW.
17 Choose Express (or Custom if you have a lot of prior installation
experience).
18 Select an appropriate Workstation Template, or create one.
19 Under Network Adapter Information, choose other network
adapter, with NDIS enabled, and enter the following information:
IN THE NON-SUPPORTED NETWORK ADAPTER WINDOW
DRIVER FILE: A:\M16BNDIS.EXE
PROTOCOL.INI STUB: A:\DEC\PROTOCOL.INI
Skip the Additional Files section and ensure Ethernet box is
enabled.
20 Insert Intel Disk 2, Network Drivers Disk when prompted.
21 In the Network Adapter Information window, select M16BNDIS
Unsupported Network Adapter with NDIS Box enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-9
22 In LAN Manager System Service Connection Information window,
enter username and press Enter.
23 Enter the Windows directory path.
24 Press Enter to add the STARTNET.BAT file to your
AUTOEXEC.BAT file.
25 A PROTOCOL.INI file created by SETUP will display in edit
mode.
a
Remove the semicolon at the beginning of the ni_irq line, as
follows:
Change the line
;NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]
to read
NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]
The ni_irq value must be the same as the interrupt value used for
the Intel adapter.
b
Verify that the [M16BNDIS]` section has the following lines and
settings:
[M16BNDIS]
DRIVERNAME=INTEL$
26 Exit SETUP and reboot to start the network. (Some machines may
require a cold boot at this point—power the computer down and
back up again.)
FTP Software LANWatch
Packet and NDIS 2.0 Drivers
FTP Software’s LANWatch network monitor software can be installed
using Intel’s packet or NDIS 2.0 drivers. For information on which driver
is appropriate for your network environment, refer to the FTP LANWatch
documentation.
FTP Software LANWatch Packet Driver Installation
1 Run the Intel Installation Program from the Installation Disk.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-10 PRO/100 LAN+Modem PC Card User’s Guide
2 Choose FTP LANWatch from the Select Network Operating
System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install LANWatch according to the instructions in your FTP
LANWatch manual.
5 Copy the file M16BPD.COM from the C:\INTEL\M16B directory
to the directory where your LANWatch files are stored.
6 (This step is not required for LANWatch versions 3.0 and later.)
Using a text editor, add the following line to your CONFIG.SYS
file:
DEVICE = [PATH]IFCUST.SYS
where [path] is the drive and directory where your LANWatch files
are stored.
7 Reboot the PC.
8 Change to the directory of where your LANWatch files are stored
and run M16BPD.COM.
9 Run LW.EXE.
FTP Software LANWatch NDIS 2.0 Driver Installation
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose FTP LANWatch from the Select Network Operating
System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install LANWatch according to the instructions in your FTP
LANWatch manual.
5 Using a text editor, add the following lines to your CONFIG.SYS
file:
DEVICE = C:\NDIS\PROTMAN.SYS /I:C:\NDIS
DEVICE = C:\NDIS\FTPSOFT.DOS
DEVICE = C:\NDIS\M16BNDIS.EXE
DEVICE = C:\NDIS\DIS_PKT.GUP
(Include the following line for LANWatch versions earlier than 3.0
only)
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-11
DEVICE = C:\LW\IFCUST.SYS
6 Create a directory called NDIS on your hard disk, by typing:
MD NDIS
7 At the DOS prompt, copy M16BNDIS.EXE from the
C:\INTEL\M16B directory on your hard disk and the file
PROTOCOL.FTP from the \NDIS directory on the Intel Network
Drivers Disk to the \NDIS directory you created in Step 6.
8 Use a text editor to modify the PROTOCOL.FTP file to match the
keywords and values in the sample PROTOCOL.INI file in the
\INTEL\M16B directory.
9 Copy all the files from the \NDIS directory on the FTP Unsup-
ported Software Disk A to the \NDIS directory created in Step 6.
10 Reboot the PC.
11 Change to the \NDIS directory and run NETBIND.EXE.
12 Run LW.EXE.
FTP Software PC/TCP
Packet, NDIS 2.0, and ODI Drivers
The PC/TCP Generic Ethernet Kernel ETHDRV.EXE can be installed
using Intel’s Packet, ODI, or NDIS drivers. PC/TCP can also be used
concurrently with NetWare. For information on which driver is appropri-
ate for your network environment, see the FTP PC/TCP documentation.
For environments using values other than those set by the Intel Installa-
tion Program, see the heading Windows 3.x Network Driver Parameters
later in this chapter.
FTP PC/TCP 3.X with OnNet 1.1 and Windows for
Workgroups 3.11
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 From the Select Network Operating System screen, choose Win-
dows for Workgroups then FTP PC/TCP 3.x.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Run the PC/TCP installation program OnNet 1.1
Download from Www.Somanuals.com. All Manuals Search And Download.
4-12 PRO/100 LAN+Modem PC Card User’s Guide
5 Follow the prompts to the Network Card Screen, then select “Other
NDIS Driver or Updated Packet Driver.”
6 Insert Intel Disk 2, Network Drivers Disk when prompted.
7 Choose the appropriate driver then follow prompts to complete the
installation.
8a For NDIS installation, reboot the PC.
8b For ODI installation, do not reboot. Continue with step 9.
Additional Steps for ODI Installation
If you are using an ODI driver, continue with the following steps:
9 Change to the directory into which PC/TCP was installed.
10 Use a text editor to change the file PCTCP.INI as follows:
• In the section PCTCP ifcust 0 change the line
INTERFACE-TYPE=NDIS
to read
INTERFACE-TYPE=PKTDRV
11 Save the file and exit the text editor.
12 Change to the C:\ (root) directory.
13 Use a text editor to modify the AUTOEXEC.BAT file as follows
(\PCTCP is the default installation directory):
• Move the line containing the STARTNET.BAT command or the
lines containing the network driver files to immediately above the
line
SET PCTCP=C:\PCTCP\PCTCP.INI
• Add the line
C:\PCTCP\ODIPKT
after the line
PCTCP=C:\PCTCP\PCTCP.INI
14 Save the file and exit the text editor.
15 Copy the file ODIPKT from disk 5 of the FTP PC/TCP installation
disks to the directory into which PC/TCP was installed.
16 Reboot the PC.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-13
FTP PC/TCP 3.X with OnNet 1.1 with Windows 3.1
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 From the Select Network Operating System screen, choose FTP
PC/TCP.
3 Follow the prompts to complete the Intel installation.
4 Run the PC/TCP installation program OnNet 1.1.
5 When prompted, insert Intel Disk 2, Network Drivers Disk.
6 Follow prompts to complete the PC/TCP installation.
7a For an NDIS installation, reboot the PC.
7b For ODI installation, do not reboot. Continue with step 8.
Additional Steps for ODI Installation
If you are using an ODI driver, continue with the following steps:
8 Change to the directory into which PC/TCP was installed.
9 Use a text editor to change the file PCTCP.INI as follows:
• In the section PCTCP ifcust 0 change the line
INTERFACE-TYPE=NDIS
to read
INTERFACE-TYPE=PKTDRV
10 Save the file and exit the text editor.
11 Change to the C:\ (root) directory.
12 Use a text editor to modify the AUTOEXEC.BAT file as follows
(\PCTCP is the default installation directory):
• Move the line containing the STARTNET.BAT command or the
lines containing the network driver files to immediately above the
line
SET PCTCP=C:\PCTCP\PCTCP.INI
• Add the line
C:\PCTCP\ODIPKT
after the line
PCTCP=C:\PCTCP\PCTCP.INI
13 Save the file and exit the text editor.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-14 PRO/100 LAN+Modem PC Card User’s Guide
14 Copy the file ODIPKT from disk 5 of the FTP PC/TCP installation
disks to the directory into which PC/TCP was installed.
15 Reboot the PC.
FTP Software PC/TCP Packet Driver Installation with
OnNet 1.1
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose FTP PC/TCP from the Select Network Operating System
screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Exit to DOS, switch to the C:\INTEL\M16B directory and run
M16BPD.COM.
5 Install PC/TCP software according to the directions given in the
PC/TCP documentation.
6 Copy the file M16BPD.COM from the C:\INTEL\M16B directory
to the PC/TCP directory specified in the PC/TCP install procedure.
7 Edit the AUTOEXEC.BAT file and add the following lines:
C:\PCTCP\M16BPD.COM
C:\PCTCP\ETHDRV.EXE
8 (This step is not required for PC/TCP versions 2.10 and later.)
Using a text editor, add the following lines to your CONFIG.SYS
file:
DEVICE=[PATH]IPCUST.SYS
DEVICE=[PATH]IFCUST.SYS
where [path] is the drive and directory specified at the PC/TCP
installation.
9 Reboot the PC.
10 Change to the directory where your PC/TCP files are stored and
run M16BPD.COM by typing:
M16BPD
11 Run the ETHDRV.EXE kernel program supplied with PC/TCP.
This loads the PC/TCP kernel into memory. The packet driver must
always load before the kernel.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-15
12 Continue your server or workstation startup as instructed in the
PC/TCP documentation.
ODI with FTP Software PC/TCP and NetWare
If you need to run Novell NetWare concurrently with FTP PC/TCP,
proceed as follows:
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose FTP PC/TCP from the Select Network Operating System
screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install PC/TCP according to the instructions in your FTP PC/TCP
manual.
5 (This step is not required for PC/TCP versions 2.10 and later.)
Using a text editor, add the following lines to your CONFIG.SYS
file:
DEVICE=[PATH]IPCUST.SYS
DEVICE=[PATH]IFCUST.SYS
where [path] is the drive and directory specified in the PC/TCP
installation.
6 Copy NET.CFG from the C:\INTEL\M16B directory and the files
LSL.COM and M16BODI.COM from the root directory of the
Intel Network Drivers Disk to the PC/TCP directory created in the
PC/TCP install procedure.
7 To start the workstation, load the software as follows:
LSL
M16BODI
IPXODI
ODIPKT (USE THE VERSION SUPPLIED WITH PC/TCP)
ETHDRV
VLM
8 Change to the network drive (usually F:\LOGIN).
9 Log in to the network.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-16 PRO/100 LAN+Modem PC Card User’s Guide
Generic Installation
If your network operating system is not listed in the Intel Installation
Program, you can try selecting “Generic NDIS Driver” or “Generic ODI
Driver” in the Intel Installation Program and clicking the Install button. A
sample configuration file containing parameters optimized for your system
will be created in the \INTEL\M16B directory on your hard disk. For
NDIS, this will be a custom PROTOCOL.INI file. For ODI, it will be a
custom NET.CFG file. Use this sample file to assist you in configuring the
actual configuration file for your system (or use the sample file itself if
appropriate).
HP LAN Manager
NDIS 2.0 Driver
See Microsoft LAN Manager.
IBM Local Area Network Support Program
IBM Local Area Network Support Program (version
1.36)
NDIS 2.0 Driver
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose IBM LAN Support Program from the Select Network
Operating System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install the IBM Local Area Network Support Program according to
the instructions in the IBM Local Area Network Support Program
User’s Guide.
5 Under Environment Information, respond “no” to the question
“Do you have adapter option disks?”
6 Choose any adapter from the list provided.
7 If prompted to do so, insert the Intel Disk 2, Network Drivers Disk
when prompted and type the path
A:\NDIS
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-17
8 Press Esc twice to bypass error messages.
9 Continue with the installation until finished.
10 Use a text editor to add the following two lines in your
CONFIG.SYS file at the location indicated by the “rem” statement
concerning insertion of the driver name:
DEVICE=\LSP\M16BNDIS.EXE
11 Copy M16BNDIS.EXE from the directory C:\INTEL\M16B to
the C:\LSP directory on your hard disk.
12 Use a text editor to edit the PROTOCOL.INI keyword settings in
the C:\LSP directory to match the keywords contained in the
sample PROTOCOL.INI file located at C:\INTEL\M16B as
required (unless you are using Intel PRO/100 default settings).
13 Save the files and reboot the PC.
IBM Local Area Network Support Program (version 1.2)
NDIS 2.0 Driver
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose IBM LAN Support Program from the Select Network
Operating System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install the IBM Local Area Network Support Program according to
the instructions in the IBM Local Area Network Support Program
User’s Guide. The following instructions refer to the prompts and
messages displayed with the Configuration Aid automated install
software provided with the LAN Support Program.
5 If a message appears during the LAN Support Program installation
indicating there are no IBM LAN adapters installed in the worksta-
tion, bypass the message by pressing Enter.
6 Answer [N]o to program support for the PC Network Adapter.
7 Answer [Y]es to use of programs needing the NETBIOS interface.
8 When prompted, select the Etherand Network family of network
cards.
9 Continue with the installation until finished.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-18 PRO/100 LAN+Modem PC Card User’s Guide
10 Use a text editor to replace the line in your CONFIG.SYS file that
reads:
DEVICE=\XX.DOS
with the line
DEVICE=\M16BNDIS.EXE
11 Still in the CONFIG.SYS file, add the parameter O=N (where O is
a letter, not zero) to the line
DEVICE=\DXMT0MOD.SYS
as follows
DEVICE=\DXMT0MOD.SYS O=N
12 Copy M16BNDIS.EXE from the directory C:\INTEL\M16B to
the root directory of your hard disk or boot disk.
13 Change to the LANMAN directory on your hard disk or boot disk.
14 Use a text editor to modify the PROTOCOL.INI file in the C:\LSP
directory as follows:
• Under the ETHERAND section, change the line that reads
BINDINGS = TCMAC2
to:
BINDINGS = INTELNET
• Underneath that section insert a new section that reads:
[INTELNET]
DRIVERNAME = INTEL$
15 Use a text editor to edit the keyword settings in the
PROTOCOL.INI file in the C:\LSP directory to match the
keywords contained in the sample PROTOCOL.INI file located at
C:\INTEL\M16B as required (unless you are using Intel PRO/100
default settings).
16 Save the file and reboot the PC.
IBM PC LAN and IBM DOS LAN Requester
1 Install the IBM LAN Support Program according to the instructions
under the heading “IBM Local Area Network Support Program,”
which immediately precedes this one.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-19
2 Reboot the PC.
3 Install IBM PC LAN or IBM DOS LAN Requester according to the
instructions in the IBM documentation.
4 Reboot the PC.
Manual Installation
All network drivers provided on Intel Disk 2, Network Drivers Disk can
be installed manually, without the Intel Installation Program. You must
copy the correct driver files to your hard disk and make appropriate
changes to CONFIG.SYS, AUTOEXEC.BAT, and configuration files
such as NET.CFG (for ODI) or PROTOCOL.INI (for NDIS). Manual
installation should only be performed by a system administrator or
someone with equivalent knowledge of the installation process for
your network operating system.
Note
For manual installation of Novell NetWare with VLM (available
only under MS-DOS or Windows 3.x) you must first decompress
the VLM files by running the MS-DOS batch file
DCOMPVLM.BAT from the Network Drivers Disk, as follows:
DCOMPVLM [PATH]
where [path] is the directory for NetWare files (usually
C:\NWCLIENT). DCOMPVLM will decompress and copy all
required files to the designated directory.
For an overview of the installation process, see the instructions provided
for your network operating system in the alphabetical section of this
chapter. Consult the section Windows 3.x Network Driver Parameters
later in this chapter for detailed information on configuration files and
settings. For additional information, consult your network operating
system documentation.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-20 PRO/100 LAN+Modem PC Card User’s Guide
Microsoft LAN Manager
Microsoft LAN Manager (version 2.1)
NDIS 2.0 Driver
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose Microsoft LAN Manager from the Select Network Operat-
ing System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Begin installation of LAN Manager using “setup.”
5 When prompted to select the available network adapter driver,
choose “Other Driver.”
6 When prompted, insert Intel Disk 2, Network Drivers Disk.
7 Select “Intel EtherExpress PRO/100 LAN+Modem PC Card”
from the menu.
8 Continue with the installation until it is completed.
9 If installing Microsoft LAN Manager to run under Windows
proceed to step 10. Otherwise, skip to step 15.
10 Run Windows.
11 Choose setup from “Main” group.
12 Select Startup, and under the “Options” screen select Change
System Settings.
13 Select Network then scroll to LAN Manager version 2.1.
14 Follow the prompts to complete the installation.
15 Reboot the PC.
Microsoft LAN Manager (version 2.1) with Windows for
Workgroups 3.11
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose Microsoft Windows for Workgroups from the Select
Network Operating System screen.
3 Select “Yes” on the Attached to Network File Server screen.
4 Select Microsoft LAN Manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-21
5 Follow the prompts to complete the Intel segment of the installa-
tion.
6 Start Windows and, in the Network program group, double-click on
the Network Setup icon.
7 If you have not installed network support, choose Networks in the
Network Setup dialog box, select Install Microsoft Windows
Network, and click OK. Otherwise proceed with step 8.
8 In the Network Setup dialog box, choose Drivers.
9 In the Network Drivers dialog box, choose Add Adapter.
10 In the Add Network Adapter box, choose Unlisted or Updated
Network Adapter and click OK.
11 When prompted for an “unlisted, updated, or vendor-provided
network driver disk,” insert the Intel Network Drivers Disk.
12 Select “Intel M16B NDIS 2.01 Real Mode,” and click OK.
13 Close the Network Drivers dialog box and click OK in the Network
Setup box.
14 Complete the installation process, inserting Intel Disk 2, Network
Drivers Disk if required.
15 Continue with the installation until it is completed.
16 Click on the Control Panel in the “Main” group.
17 Select Startup from the Control Panel.
18 In the Options for Enterprise Networking window click “Log on to
Windows NT or LAN Manager Domain.”
19 Save, exit, and reboot the PC.
Windows for Workgroups
NDIS 2.01 and ODI Drivers
Instructions are provided for installing Intel network drivers for the first
time on a system using Windows for Workgroups version 3.11 alone or
with NetWare. These instructions assume that Windows for Workgroups
has already been installed. Remove any earlier version of the Intel drivers
before installing the new version. No NDIS 3 driver is supplied for
Windows for Workgroups.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-22 PRO/100 LAN+Modem PC Card User’s Guide
The following topics are covered for Windows for Workgroups:
• How to install for Windows for Workgroups version 3.11 and
NetWare using the ODI driver
• How to install for Windows for Workgroups 3.11 using the NDIS
2.0 driver
• How to Disable Windows for Workgroups Networking
For troubleshooting tips for Windows for Workgroups, see Chapter 4.
Troubleshooting.
Windows for Workgroups Version 3.11 and NetWare
(Using the ODI driver)
1 To configure Windows for Workgroups with NetWare, run the Intel
Installation Program from Disk 1 and choose Windows for Work-
groups.
2 Choose YES to “Connect to Network Server.”
3 Choose “Novell NetWare” as your network server.
4 When the installation is complete, reboot the computer.
5 At the Intel menu, choose “Load Intel EtherExpress PRO/100
LAN+Modem PC Card for Network Access.”
6 From the DOS prompt, run the NetWare Client install. Be sure to
install support for Windows.
7 When the Novell Client install program asks for an ODI driver,
insert the Intel Network Drivers Disk.
8 Complete the installation process and reboot the computer.
9 Log in to NetWare.
10 Start Windows for Workgroups and, in the Network program
group, double-click on the Network Setup icon.
Windows for Workgroups Network Setup will detect the NetWare
configuration and automatically select Novell NetWare as an
additional network. It will also prompt for Novell support files
(from Novell Client diskettes) if required during the installation. (If
necessary, use the Novell decompression utility to decompress the
required files.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-23
Windows for Workgroups Setup will also attempt to determine what
NetWare driver model you are using. If for some reason Windows
for Workgroups was unable to detect the driver model, you should
select IPXODI and LSL as the driver type.
Note that you can install NetWare as an additional network under
Windows for Workgroups, as follows:
11 In the Network Setup dialog box, choose Networks.
12 To install both Windows for Workgroups and NetWare, choose
Install Microsoft Windows Network.
13 Choose Other under Additional Network Support, then select the
NetWare configuration appropriate for your network.
14 If you want to share your files or printers with others, select
“Sharing.”
15 In the Network Setup dialog box, choose Drivers.
16 In the Network Drivers dialog box, choose Add Adapter.
17 In the Add Network Adapter box, choose Unlisted or Updated
Network Adapter and click OK.
18 When prompted for an “unlisted, updated, or vendor-provided
network driver disk,” insert the Intel Network Drivers Disk and
click OK.
19 Select “Intel M16B ODI for NetWare” and click OK.
20 Close the Network Drivers dialog box and click OK in the Network
Setup box.
21 Complete the installation process, inserting Intel Disk 2: Network
Drivers Disk if required.
22 Reboot the computer.
Note
Verify that the following lines have been added to your
AUTOEXEC.BAT and STARTNET.BAT files. If they are not
there, add them manually using a text editor.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-24 PRO/100 LAN+Modem PC Card User’s Guide
Add the following command to the AUTOEXEC.BAT file,
where \WINDOWS is the directory into which Microsoft
Windows was installed:
C:\WINDOWS\NET START
Add the following command to the STARTNET.BAT file in
your NWCLIENT directory, where \WINDOWS is the directory
into which Microsoft Windows was installed:
C:\WINDOWS\ODIHLP.EXE
Windows for Workgroups 3.11 Using the NDIS 2.0
Driver
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose Microsoft Windows for Workgroups installation from the
Select Network Operating System screen.
3 Choose “No” on the Attached to Network File Server screen.
4 Follow the prompts to complete the Intel segment of the installa-
tion.
5 Start Windows for Workgroups and double-click on the Network
Setup icon in the Network Group.
6 If you have not installed network support, choose Networks in the
Network Setup dialog box, select Install Microsoft Windows
Network, and click OK. Otherwise proceed to Step 7. Click the
Sharing button to share files and printers.
7 In the Network Setup dialog box, choose Drivers.
8 In the Network Drivers dialog box, choose Add Adapter.
9 In the Add Network Adapter box, choose Unlisted or Updated
Network Adapter and click OK.
10 When prompted for an “unlisted, updated, or vendor-provided
network driver disk,” insert the Intel Network Drivers Disk.
11 Select “Intel M16B NDIS 2.01 Real Mode” and click OK.
12 Close the Network Drivers dialog box and click OK in the Network
Setup box.
13 Complete the installation process, inserting Intel Disk 2, Network
Drivers Disk if required.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-25
How to Remove an Existing Windows for Workgroups
Installation
1 Start Windows and select Network Setup in the Network program
group.
2 In the Network Setup dialog box, choose Drivers.
3 In the Network Drivers dialog box, choose Remove to discard any
existing network adapter drivers.
4 Choose Close and return to the Network Setup dialog box.
5 Exit the Network Setup program and exit Windows.
6 At the DOS prompt, change to the Windows system directory, as
follows
CD \WINDOWS\SYSTEM
7 Make a directory called OEM, as follows
MKDIR OEM
8 Type
DIR OEM?.INF
to see a list of driver configuration files.
9 Use the DOS EDIT program to view each OEM file to determine
which ones reference Intel.
10 Copy the old Intel configuration files to the OEM directory.
11 Delete the old Intel configuration files from the Windows system
directory.
12 Restart Windows.
13 Follow the instructions for installing drivers for Windows for
Workgroups alone or Windows for Workgroups and NetWare.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-26 PRO/100 LAN+Modem PC Card User’s Guide
Novell NetWare
ODI Driver
The Intel ODI driver allows for the concurrent use of Novell NetWare
and other protocols that support Novell’s Open Data-Link Interface
(ODI) specification.
NetWare
1 Run the Intel Installation Program from the Installation Disk.
2 Choose Novell NetWare from the Select Network Operating
System screen.
3 Follow the prompts to complete the installation.
4 The Intel Installation Program will reboot the computer and verify
the NetWare connection.
5 Log in to the network.
Note
The Intel Installation Program uses the NetWare VLM shell to
connect to your NetWare server. The Installation Program
decompresses and copies all the required files.
If you are installing manually, without the Intel Installation
Program (under MS-DOS or Windows 3.x) you must first
decompress the VLM files by running the MS-DOS batch file
DCOMPVLM.BAT from the Network Drivers Disk, as follows:
DCOMPVLM [PATH]
where [path] is the directory for NetWare files (usually
C:\NWCLIENT). DCOMPVLM will decompress and copy all
required files to the designated directory.
If you need NETX shell support, contact your System Adminis-
trator.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-27
SunSoft PC-NFS (version 3.5)
NDIS 2.0 Driver
1 Run the Intel Installation Program from the Installation Disk.
2 Choose SunSoft PC-NFS from the Select Network Operating
System screen.
3 Follow the prompts to complete the Intel installation.
4 Install PC-NFS for Ethernet according to instructions in the PC-
NFS documentation. Choose NDIS setup, and follow the
instructions to complete the setup. Note the prompt that tells you
that further manual modifications will have to be made.
5 Reboot the computer. You will see some error messages. Disregard
them and continue with these instructions.
6 Rename the file PROTOCOL.NFS in the C:\LANMAN directory
to PROTOCOL.INI. Use an text editor to edit the
PROTOCOL.INI file as follows:
Replace the items
[YOUR-MAC-MODULE]
DRIVERNAME = YOURMAC$
OPTION1 = VALUE1 ETC.
[NFS-NDIS]
DRIVERNAME = NFSLINK1
BINDINGS = YOUR-MAC-MODULE
with
[INTELNET]
DRIVERNAME = INTEL$
[NFS-NDIS]
DRIVERNAME = NFSLINK$
BINDINGS = INTELNET
7 Copy M16BNDIS.EXE from the C:\INTEL\M16B directory to
the C:\LANMAN directory.
8 Use a text editor to insert the following lines in your CONFIG.SYS
file:
Download from Www.Somanuals.com. All Manuals Search And Download.
4-28 PRO/100 LAN+Modem PC Card User’s Guide
DEVICE=C:\LANMAN\M16BNDIS.EXE
between the two lines
DEVICE=C:\LANMAN\PROTMAN.SYS
DEVICE=C:\LANMAN\NFS-NDIS.SYS
as follows:
DEVICE=C:\LANMAN\PROTMAN.SYS
DEVICE=C:\LANMAN\M16BNDIS.EXE
DEVICE=C:\LANMAN\NFS-NDIS.SYS
9 Verify that your AUTOEXEC.BAT file contains a line that reads
C:\LANMAN\NETBIND
before the line that reads
NET INIT
10 Configure PC-NFS options according to your PC-NFS documenta-
tion, and reboot the computer.
Ungermann-Bass Net/One for DOS
NDIS 2.0 Driver
The PRO/100 PC Card is supported on Ungermann-Bass Net/One LAN
Manager and MS-NET networks. There are two NDIS driver packages
available from UB: XNS BNS/NDIS and TCP BNS/NDIS. These
packages, used with a Intel NDIS driver, provide files that support DOS
workstations. They are available from UB and authorized UB representa-
tives.
Ungermann-Bass Net/One LAN Manager version 2.1
Installation
1 Begin installation of LAN Manager 2.1 using “setup.”
2 When prompted to select the available network adapter driver,
choose “Other Driver.”
3 When prompted, insert the Intel Network Drivers Disk.
4 Select “Intel EtherExpress™ PRO/100 LAN+Modem PC Card”
from the menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-29
5 Continue with the installation until it is completed.
6 Following the UB instructions, modify your CONFIG.SYS file by
adding the following lines:
For DOS:
DEVICE = [PATH]M16BNDIS.EXE
where [path] is the drive and directory in which you installed your
network operating system.
7 Use a text editor to modify your PROTOCOL.INI file as follows:
• For each protocol that you want to bind, set the protocol
definition area of the PROTOCOL.INI file to:
BINDINGS = UBLOOP
• At the end of the file, add the following fragments:
[UBLOOP]
DRIVERNAME = UBLOOP$
BINDINGS = INTELNET
;INTEL ADAPTER
[INTELNET]
DRIVERNAME = INTEL$
8 Reboot the PC.
Wollongong PathWay Access for DOS
NDIS and ODI Drivers
Wollongong PathWay Access for DOS can be installed using Intel NDIS
or ODI drivers. Installation instructions for both types of driver are
provided below. For information on which driver is appropriate for your
network environment, refer to the Wollongong PathWay Access for DOS
documentation.
Wollongong PathWay NDIS Installation
1 Run the Installation Program from Intel Disk 1, Installation Disk.
2 Choose Wollongong PathWay Access from the Select Network
Operating System screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-30 PRO/100 LAN+Modem PC Card User’s Guide
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install PathWay Access for DOS Kernel and Drivers programs
according to the instructions in the PathWay Access for DOS
manual. Before rebooting the PC, continue with the following steps.
5 Use a text editor to modify the CONFIG.SYS file. After the
statement that reads
DEVICE=C:\PATHWAY\PWTCP.SYS
add the lines
DEVICE=\PATHWAY\[PROTMAN FILE] /I:C:\PATHWAY
DEVICE=\PATHWAY\M16BNDIS.EXE
where [PROTMAN FILE] is equal to the PROTMAN2.EXE or
PROTMAN.EXE file that is located in your PATHWAY directory.
(Refer to the Wollongong PathWay Access for DOS manual for
information regarding the differences between these two files.)
6 Copy the file M16BNDIS.EXE from C:\INTEL\M16B directory
to the PATHWAY directory on your hard disk or boot disk.
7 Continue with the “custom” instructions in the PathWay Access for
DOS manual.
8 Reboot the PC.
Wollongong PathWay ODI Installation
1 Run the Intel Installation Program from the Installation Disk.
2 Choose Wollongong PathWay Access from the Select Network
Operating System screen.
3 Follow the prompts to complete the Intel segment of the installa-
tion.
4 Install PathWay Access for DOS Kernel and Drivers programs
according to the instructions in the PathWay Access for DOS
manual. Before rebooting the PC, perform the following steps.
5 Run the MS-DOS batch file DCOMPVLM.BAT from the Network
Drivers Disk, as follows:
DCOMPVLM PATHWAY
DCOMPVLM.BAT will decompress and copy all required files
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-31
from the Intel Network Drivers Disk to the PATHWAY directory
on your hard disk or boot disk. (The files are LSL.COM,
M16BODI.COM, IPXODI.COM, VLM.EXE, and NET.CFG.)
6 Change to the PATHWAY directory and load the software in the
following order:
LSL
M16BODI
IPXODI
VLM
(ONLY IF USING NOVELL NETWARE)
(ONLY IF USING NOVELL NETWARE)
7 Load the Wollongong file ODI.EXE.
8 Continue with the instructions in the PathWay Access for DOS
manual.
9 Reboot the PC.Windows 3.x
Windows 3.x Modem Configuration Notes
The PRO/100 PC Card doubles as a LAN card and fax/modem. As a
modem, the PRO/100 PC Card features Hayes and Microcom compatibil-
ity and the latest in data transmission, data compression, and error control
techniques. It can be used with most standard communications and fax
software packages.
Note
Unless Card and Socket Services are being used under Windows
3.x, the PRO/100 PC Card requires that a LAN+modem driver
(M16BODI.COM, M16BNDIS.EXE, or M16BPD.COM) or a
modem-only driver (IMENABLE.COM) be loaded before the
modem can be used.
For more detailed modem information, see Chapter 6. Modem Reference
in this User’s Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-32 PRO/100 LAN+Modem PC Card User’s Guide
Using Network or Modem
Communications under Windows 3.x
All Intel Windows 3.x network drivers initialize both the LAN and the
modem. When a network driver is loaded, the modem driver is automati-
cally initialized.
Using Modem Communications Only under Windows
3.x
If you want to use the modem under Windows 3.x without loading a
network driver, and you are NOT using Card and Socket Services, reboot
the computer and run the utility IMENABLE.COM (found in the root
directory of Intel Disk 2, Network Drivers Disk) from the DOS prompt
before launching Windows or your communications program:
IMENABLE
Installing Communications and Fax Software
The PRO/100 PC Card is compatible with most popular communications
and fax software packages (see Chapter 5. Utilities and Applications for
application-specific information).
Running Windows Communications and Fax Software
Windows 3.x-based fax and communications programs can be started
immediately once the modem has been initialized.
Running DOS Communications and Fax Software
DOS-based communications software should be run from a DOS prompt
without Windows loaded. DOS software can also be run in a DOS box
with Windows loaded.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-33
COM Ports, IRQs, and I/O Base Addresses
Automatic COM Port Detection
The PRO/100 PC Card drivers will automatically configure a COM port
on the system. The driver scans the BIOS table for the first unused COM
port, then checks to see if the corresponding IRQ is in use. If it is, it
moves to the next available COM port.
This process takes precedence over the network resources. If you specify a
network IRQ that is the same as the first available COM IRQ (3 or 4), the
driver will respond with an error.
To force a COM port, use the COMx keyword described in the following
heading. If you do not want a COM port, add the NOCOM keyword to
your configuration file or command line.
Manually Setting COM Port, Interrupt, and I/O Address
Values
Use the COMx keyword to manually specify which COM port the PRO/
100 PC Card should use when providing erial port emulation for modem
operations. Values for x can be 1, 2, 3, or 4. Each of these settings also
activates a specific set of predefined values for I/O address and interrupt
level, as follows:
PORT
COM1
COM2
COM3
COM4
IRQ
IOADDRESS
03F8
4
3
4
3
02F8
03E8
02E8
Do not select a COM port that is currently used by any other system
device, such as the PC Card interface itself, or a mouse or trackball.
Note
Configure your communications software to the COM port you
selected with the COMx keyword.
By default the LAN drivers will select the first open COM port. You can
add the COMx keyword and a port number to the LAN driver configura-
Download from Www.Somanuals.com. All Manuals Search And Download.
4-34 PRO/100 LAN+Modem PC Card User’s Guide
tion to activate serial port emulation. The COMx keyword can also be
stated on the command line with the modem-only driver
IMENABLE.COM.
Use the keywords COMIRQ and COMBASE to override the values set
with COM1, COM2, COM3, or COM4 in case of a conflict between LAN
and modem settings.
Sample NET.CFG File (ODI Driver) with COM Port Setting
LINK DRIVER M16BODI
INT 10
PORT 280
MEM D2000
COM3
Sample PROTOCOL.INI (NDIS Driver) with COM Port
Setting
[INTELNET]
DRIVERNAME=INTEL$
IRQ=10
IOADDRESS=0X320
MEM=0XD2000
MODE=IO
COM4
Sample Packet Driver Command Line with COM Port
Setting
M16BPD COM3 MEM=D8000
Sample IMENABLE.COM Command Line
IMENABLE COM3 MEM=D8000
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-35
Changing Interrupt or I/O Address Settings
The COMIRQ keyword is used to override the predefined interrupt value
for a specific COM port in case of a conflict between LAN and modem
settings. It can also be used with COMBASE to select a user-defined
COM port. Default is keyword not used. Setting is a decimal value which
must be different from the value used with the INTERRUPT keyword.
The COMBASE keyword can be used to override the predefined I/O
port value for a specific COM port in case of a conflict between LAN and
modem settings. It can also be used with COMIRQ to select a user-
defined COM port. The default condition is “keyword not used.”
Parameter setting is a hexadecimal value in the range 248 to 3F8 which
must be different from the value used with the IOADDRESS or PORT
keyword. Serial emulation mode requires 8 addresses.
The SHAREIRQ keyword is only valid when no Card Services are being
used. It instructs the driver that the modem and LAN interfaces must
share the IRQ line. State this keyword to configure the interface for one
physical IRQ and one logical IRQ, instead of the two separate physical
IRQs normally used by the PC Card controller.
Preventing Memory Conflicts
Memory allocation conflicts can cause the Intel driver to fail to load. The
PRO/100 PC Card requires an 8K memory block located between C000
and EFFF, with a default starting address of D2000.
Some computers require that a different address be used. To change the
memory address at which the Intel driver loads, use the MEMORY or
MEM keyword in the driver configuration file or on the driver command
line.
Memory Manager Exclusions
When using a memory manager such as EMM386, the memory manager
will try to control the upper memory blocks where the Intel driver
normally loads. To prevent conflicts, add a statement to the EMM386
command line excluding an 8K memory block between C000 and EFFF
for the Intel driver. For example,
DEVICE=C:\PATH\EMM386.EXE NOEMS X=CC00-CDFF
Download from Www.Somanuals.com. All Manuals Search And Download.
4-36 PRO/100 LAN+Modem PC Card User’s Guide
Here are some examples of MEMORY keyword settings and the corre-
sponding 8K exclusion:
Configuration
Keyword Setting
Exclusion
NET.CFG
MEM CC000
X=CC00-CDFF
PROTOCOL.INI MEMORY=D4000 X=D400-D5FF
Command Line
MEMORY=C8000 X=C800-C9FF
Notes
Memory settings used to configure the PRO/100 PC Card
always use 5 digits. Memory settings on the EMM386 command
line only require 4 digits.
With Card and Socket Services, the memory exclusion is
generally much larger than that required without them. This
exclusion range should not be reduced.
Windows and EMM386
If you are using EMM386 and Windows, you should add an
EMMEXCLUDE= line to the [386enh] section of the SYSTEM.INI file.
The exclusion range should match the exclusion on the EMM386 line.
If you are not using EMM386, but are using Windows, then you MUST
add an EMMEXCLUDE= statement to the [386enh] section of the
SYSTEM.INI file. The exclusion range must match the memory window
the PRO/100 PC Card is using.
Windows 3.x Modem Driver Settings
The modem utility IMENABLE.COM searches for an available COM
port or one specified by the user and configures the Intel adapter hard-
ware accordingly.
Modem Driver Configuration Notes
If you want to use the modem without loading a network driver, and you
are not using Card and Socket Services or the equivalent under Microsoft
Windows 95 or NT, you have to load the modem driver
IMENABLE.COM, supplied on Disk 2. Network Drivers Disk. (If you
load a network driver such as M16BNDIS, M16BODI, or M16BPD, you
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-37
do not need IMENABLE.COM because the network drivers also initialize
the modem.)
Reboot the computer and run IMENABLE.COM from the DOS prompt
before launching Windows or a communications program.
IMENABLE.COM Keywords
KEYWORD
DEFAULT
VALID VALUES
COMX
AUTO
(X = 1, 2, 3, OR 4)
COMIRQ
NOT USED
NOT USED
AUTO
(3 TO 15)
COMBASE
IOWAITSTATES=
MEMORY=
MEMWAITSTATES=
SLOT=
(0X248 TO 0X3F8)
(1, 2, OR 3)
0XD2000
AUTO
(0XC0000 TO 0XE0000)
(1, 2, OR 3)
AUTO
(HARDWARE DEPENDENT)
(DISABLES IMENABLE)
OFF
NOT USED
Modem Driver Example
A typical sequence for loading the modem driver IMENABLE.COM with
default configuration settings is as follows:
IMENABLE.COM COMX
where COMx is a COM port value such as COM3 or COM4. If other
nondefault configuration settings are used, these must also be stated on
the IMENABLE.COM command line. For example,
IMENABLE COM4 COMBASE=0X320 COMIRQ=10
Windows 3.x Network Driver Parameters
The following paragraphs present configuration guidelines for each of the
driver types: NDIS, ODI, and packet. These guidelines are followed by a
comprehensive “keyword” reference section and a list of error messages.
All of the drivers described here automatically detect the speed of the
network to which the adapter is attached (10Mbps or 100Mbps), unless
otherwise noted. Speed can also be specified with the LINESPEED
keyword.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-38 PRO/100 LAN+Modem PC Card User’s Guide
ODI Settings (for driver M16BODI.COM)
Custom parameters for networks using the ODI driver can be entered
manually, using an ASCII editor, in the NET.CFG file.
DOS ODI Driver Configuration Notes (M16BODI.COM)
The ODI driver M16BODI.COM conforms to the “Novell ODI Specifi-
cation: 16-bit DOS Client HSMs.” It is a DOS-based
terminate-and-stay-resident (TSR) program. The driver will configure itself
according to the options specified in the NET.CFG file. This file is
supplied on Disk 2, Network Drivers Disk and must be present in the
same directory as the ODI driver. Files required for using
M16BODI.COM are
M16BODI.INS
NET.CFG
Intel installation information file
Network configuration file
Intel ODI driver
M16BODI.COM
Most installations will be able to use the settings detected by the driver. If
any parameters need to be changed, use an ASCII text editor to open and
modify the NET.CFG file and insert the appropriate keywords and values
after the line
LINK DRIVER M16BODI
Parameters can also be implemented on the command line. Keyword
syntax can be found below. Keywords are not case sensitive. A Keyword
Alphabetical Reference follows the discussion of keyword syntax.
NET.CFG Example
LINK DRIVER M16BODI
INT 5
PORT 280
MEM D2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-39
M16BODI.COM Keywords
KEYWORD
DEFAULT
VALID VALUES
(X = 1, 2, 3, OR 4)
(3 TO 15)
COMX
AUTO
AUTO
AUTO
AUTO
AUTO
0
COMIRQ=
COMBASE=
INTERRUPT
IOADDRESS
IOWAITSTATES
LINESPEED
LINKDISABLE
(0X248 TO 0X3F8)
(3 - 15)
(240 - 380)
(1 - 3)
AUTO
(10 OR 100)
(NO KEYWORD = LINK INTEGRITY ENABLED)
LINK DRIVER M16BODI (REQUIRED FIRST ITEM IN NET.CFG)
MEMORY
AUTO
0
(C0000 - EE000)
(1 - 3)
MEMWAITSTATES
MODE
MEM
(MEM OR IO)
NOCHECK
(NO KEYWORD = ADAPTER RESOURCE VERI-
FICATION ENABLED)
NOCOM
NOEARLYRX
NOEARLYTX
NOLED
(NO KEYWORD = MODEM ENABLED)
(NO KEYWORD = EARLY RECEIVE ENABLED)
(NO KEYWORD = EARLY TRANSMIT ENABLED)
(NO KEYWORD = LEDS ENABLED)
S
(COMMAND LINE ONLY: SHOW RESIDENT LAN
DRIVERS)
SHAREIRQ
SOCKET
U
AUTO
(1 - 4)
NOT USED
(COMMAND LINE ONLY:
UNLOAD M16BODI)
WORDSIZE
16
(8 OR 16)
ODI Driver Example
A typical load sequence for the ODI driver M16BODI.COM in a
NetWare environment would be
LSL
M16BODI
IPXODI
VLM
Download from Www.Somanuals.com. All Manuals Search And Download.
4-40 PRO/100 LAN+Modem PC Card User’s Guide
NDIS 2.0.1 Settings (for driver
M16BNDIS.EXE)
Custom parameters for the NDIS driver can be entered manually, using an
ASCII editor, in the PROTOCOL.INI file.
NDIS 2.0.1 DOS Driver Configuration Notes
The DOS NDIS driver M16BNDIS.EXE conforms to the Microsoft
Network Driver Interface Specification (NDIS) version 2.0.1. It is a DOS-
based executable terminate-and-stay-resident (TSR) program that will
configure itself according to the options specified in the PROTOCOL.INI
file, which is supplied on Disk 2. Network Drivers Disk.
The files required for using M16BNDIS.EXE are:
PROTOCOL.INI
M16BDOS.NIF
M16BNDIS.EXE
Configuration and binding informa
tion file
Intel installation file for Microsoft
LAN Manager
Intel DOS NDIS 2.0.1 driver
Most installations will be able to use the settings detected by the driver. If
any parameters need to be changed, use an ASCII text editor to modify
the PROTOCOL.INI file with the appropriate keywords and values.
Keyword syntax for PROTOCOL.INI can be found below. Keywords are
not case sensitive, and can be abbreviated to a unique sequence of initial
characters (for example, IN for INTERRUPT, IO for IOADDRESS). A
Keyword Alphabetical Reference follows the keyword listings.
PROTOCOL.INI Example
[INTELNET]
DRIVERNAME=INTEL
MEM=0XD2000
MODE=IO
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-41
NDIS 2.0.1 Keywords (M16BNDIS.EXE)
KEYWORD
DEFAULT
VALID VALUES
(X = 1, 2, 3, OR 4)
(3 TO 15)
COMX
AUTO
COMIRQ=
COMBASE=
AUTO
AUTO
(0X248 TO 0X3F8)
DRIVERNAME=INTEL$ (REQUIRED FIRST ITEM IN PROTOCOL.INI)
INTERRUPT=
IOADDRESS=
IOWAITSTATES=
LINESPEED=
LINKDISABLE
MEMORY=
AUTO
AUTO
0
(3 - 15)
(240 - 380)
(1 - 3)
AUTO
(10 OR 100)
(NO KEYWORD = LINK INTEGRITY ENABLED)
AUTO
0
(C0000 TO EE000)
(1 - 3)
MEMWAITSTATES=
MODE=
MEM
(MEM OR IO)
NOCHECK
(NO KEYWORD = ADAPTER RESOURCE VERI
FICATION ENABLED)
NOCOM
(NO KEYWORD = MODEM ENABLED)
NOEARLYRX
NOEARLYTX
NOLED
(NO KEYWORD = EARLY RECEIVE ENABLED)
(NO KEYWORD = EARLY TRANSMIT ENABLED)
(NO KEYWORD = LEDS ENABLED)
SHAREIRQ
SOCKET=
WORDSIZE=
AUTO
16
(1 - 4)
(8 OR 16)
Packet Driver Settings (for driver
M16BPD.COM)
Packet driver parameters must be stated on the M16BPD.COM command
line when running the packet driver.
Packet Driver Configuration Notes
The Intel packet driver M16BPD.COM conforms to FTP Software’s
public domain packet-driver specification. It is a DOS-based terminate-
and-stay-resident (TSR) program. The driver file M16BPD.COM is located
in the \PKTDRV directory on Disk 2, Network Drivers Disk.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-42 PRO/100 LAN+Modem PC Card User’s Guide
Refer to your network documentation for instructions on how to install
the packet driver with your network.
Keywords are not case sensitive, and can be abbreviated to a unique
sequence of initial characters (for example, IN for INTERRUPT).
Packet Driver Keywords
KEYWORD
DEFAULT
AUTO
AUTO
AUTO
AUTO
AUTO
0
VALID VALUES
(X = 1, 2, 3, OR 4)
(3 TO 15)
COMX
COMIRQ=
COMBASE=
INTERRUPT=
IOADDRESS=
IOWAITSTATES=
LINESPEED=
LINKDISABLE
MEMORY=
(0X248 TO 0X3F8)
(3 - 15)
(240 - 380)
(1 - 3)
AUTO
(10 OR 100)
(NO KEYWORD = LINK INTEGRITY ENABLED)
AUTO
0
(C0000 - E8000)
(1 - 3)
MEMWAITSTATES=
MODE=
MEM
(MEM OR IO)
NOCHECK
(NO KEYWORD = ADAPTER RESOURCE VERI
FICATION ENABLED)
NOCOM
(NO KEYWORD = MODEM ENABLED)
(NO KEYWORD = EARLYRX ENABLED)
(NO KEYWORD = EARLYTX ENABLED)
(NO KEYWORD = LEDS ENABLED)
NOEARLYRX
NOEARLYTX
NOLED
SHAREIRQ
SINT
60
(60 - 80)
(1 - 4)
SOCKET=
WORDSIZE=
AUTO
16
(8 OR 16)
Packet Driver Example
A typical sequence for loading the packet driver M16BPD.COM with
default configuration settings is as follows:
M16BPD
ETHDRV
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-43
If nondefault configuration settings are used, these must be stated on the
M16BPD.COM command line. For example,
M16BPD IOADDRESS=320 INT=7
ETHDRV
Driver Keyword Alphabetical Reference
?
displays a summary of command line options.
COMx
specifies which COM port the PRO/100 PC Card
should use when providing serial port emulation
for modem operations. Values for x can be 1, 2, 3,
or 4. Each of these values instructs the driver to
use pre-defined values for I/O address and
interrupt level, and to enable the specified I/O
address in the COM port BIOS table. The modem
driver IMENABLE.COM defaults to COM3. Use
the keywords COMIRQ and COMBASE to
override the values set with COM1, COM2,
COM3, or COM4 in case of a conflict between
LAN and modem settings.
COMBASE
can be used to override the pre-defined I/O port
value for a specific COM port in case of a conflict
between LAN and modem settings. It can also be
used with COMIRQ to select a user-defined COM
port. Default is no keyword. Parameter setting is a
hexadecimal value in the range 248 to 3F8 which
must be different from the value used with the
IOADDRESS or PORT keyword. Serial emulation
mode requires 8 addresses.
COMIRQ
is used to override the pre-defined interrupt value
for a specific COM port in case of a conflict
between LAN and modem settings. It can also be
used with COMBASE to select a user-defined
COM port. Default is no keyword. Parameter
setting is a decimal value which must be different
from the value used with the INTERRUPT
keyword.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-44 PRO/100 LAN+Modem PC Card User’s Guide
FRAME
(ODI) designates support for multiple Ethernet
frame types. One or more types can be used. Refer
to your NetWare documentation for more
information. The Intel ODI driver’s default frame
type is 802.2, but the NET.CFG file supplied with
the ODI driver on Disk 2, Network Drivers Disk
sets both 802.2 and 802.3. Therefore if your
network’s frame type is 802.3, you must use Intel’s
NET.CFG with the ODI driver.
INTERRUPT
specifies a LAN interrupt to use. It requires a
decimal value designating the PRO/100 PC Card
port hardware interrupt (for example, INT 5 or
INT 7). Default (if parameter not specified) is 5.
Any value supported by the PC Card hardware can
be used.
INTERRUPTNUMBERSee INTERRUPT.
IOADDRESS
specifies the LAN I/O address to use, in hexadeci-
mal notation. Default address is 320.
IOBASEADDRESS see IOADDRESS.
IOWAITSTATES specifies the number of wait states that should be
added to I/O accesses to the card. Values are a
decimal number from 1 to 3. On some machines it
may be necessary for the driver to run with I/O
waitstates. By default, the driver will attempt to
automatically configure this parameter. The
keyword is provided as a troubleshooting aid.
LINKINTEGRITY ON or OFF. See LINKDISABLE.
LINKDISABLE
disables the link integrity check on the network
twisted pair cabling (for operation with non-IEEE
10BASE-T networks such as StarLAN 10).
Without the LINKDISABLE keyword in the
driver command line, the driver defaults to link
integrity ENABLED.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-45
MEMORY
specifies the memory location to use. It is specified
in hexadecimal notation and is not a segment
value. Specify the full address for all drivers. For
example, D2000, not D200. The PRO/100 PC
Card uses 4 Kbytes of memory (1000 hexadecimal)
for the LAN. Use the MODE IO setting to disable
MEMORY MODE. Default is D2000. Possible
values are C0000 through E0000.
MEMORYBASEADDRESS
see MEMORY.
MEMWAITSTATESspecifies the number of wait states that should be
added to memory accesses to the card. Values are
decimal 1 to 3. On extremely fast machines it may
be necessary for the driver to run with waitstates.
By default, the driver will attempt to automatically
configure this parameter. The keyword is provided
as a troubleshooting aid.
MODE
specifies whether to run the network in memory-
mapped or I/O mode. Values are the ASCII
strings MEMORY or IO. The default setting is
MEM. Set this keyword to IO to disable requests
for memory-mapped mode on systems that only
support an I/O driven card.
NOCHECK
NOCOM
disables verification of adapter resources. This
keyword is intended to be used as a troubleshoot-
ing tool.
the PRO/100 PC Card driver will configure a
COM port by default. The NOCOM keyword can
be used to defeat this feature. If the keyword is not
used, the modem is enabled. LAN operations are
not affected.
NOEARLYRX
disables Advanced Look-ahead Pipelining features
of the PRO/100 PC Card. You may need this
keyword for NDIS version 2.01 drivers which do
not fully support the “early RX” feature.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-46 PRO/100 LAN+Modem PC Card User’s Guide
NOEARLYTX
disables early transmit features of the PRO/100
PC Card. Try using this keyword if you are
experiencing a large number of transmit overruns.
NOLEDS
PORT
turns off network LED indicators on LAN adapter
cables to conserve battery power.
(ODI) specifies the LAN I/O address to use, in
hexadecimal notation. Default address is 320.
SHAREIRQ
is optional when no Card Services are being used.
It instructs the driver that the modem and LAN
interfaces must share the IRQ line. State this
keyword to configure the interface for one physical
IRQ and one logical IRQ, instead of the two
separate physical IRQs normally used by the PC
Card controller.
SINT
(Packet Driver) is number from hexadecimal 60 to
80 designating a software interrupt. Default is 60.
SLOT
Same as SOCKET but used with
IMENABLE.COM.
SOCKET
forces the driver to look in the selected socket
specifically for a PRO/100 PC Card. If no
keyword is stated, the driver will scan all PC Card
slots looking for the right card. Valid values are
from 1 to the number of PC Card slots supported
by the computer being used. This keyword may be
useful if you have a memory card or other PC Card
device in socket 1 and a PRO/100 PC Card in
socket 2. Then set the keyword to SOCKET=2 in
your configuration file or on the command line.
WORDSIZE
this parameter specifies the size of the data path
for the LAN controller. Values are 8 or 16 decimal.
Default is 16. Since the modem always uses an 8-
bit data path, this keyword does not affect the
modem.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-47
Error Messages for Windows 3.x and
MS-DOS drivers
Except as noted, these messages are specific to the PRO/100 PC Card.
For an explanation of other messages that may appear on the screen, see
your computer and network operating system documentation.
A PCMCIA card was not detected
If the SOCKET keyword was stated, then no PC Card was detected in the
slot specified. If the SOCKET keyword was not used, then no PC Card
was detected in any slot.
An invalid I/O address was specified
The PRO/100 PC Card requires 32 consecutive I/O locations. This
message indicates that the I/O address specified does not start on a 32-
byte boundary. Examples of valid I/O addresses, in hexadecimal notation,
are 300, 320, 240. Examples of invalid I/O addresses are 301, 325, 247.
M16BODI only supports the BUS ID PC Card, not the selected
BUS ID. Either delete the BUS ID keyword from the NET.CFG file
or change its value to 3.
This message applies only to the ODI driver. Do not use the keyword
BUS ID in the ODI NET.CFG file. If you do use it, you must set the
value to 3.
Network Controller running in 8-bit mode
The Network Interface Controller (NIC) has been forced to run in 8-bit
mode with the keyword WORDSIZE set at 8 (default is 16-bit mode).
This option is used when the PC Card hardware does not support 16-bit
mode.
Network Controller running in I/O mode
The Network Interface Controller (NIC) has been forced to run in I/O-
only mode with the keyword MODE set at IO (default is MEM). This
option is used when the PC Card hardware does not support perfor-
mance-enhancing memory-mapped I/O mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-48 PRO/100 LAN+Modem PC Card User’s Guide
The card is unreadable, possible memory conflict
The Card Information Structure (CIS) of the PC Card was unreadable.
This could be a result of failure to exclude the selected memory range
from the memory managers loaded on the machine. Either exclude a 8K
memory range, select a memory range that has already been excluded, or
include the NOCHECK keyword in the configuration file.
Please specify a different interrupt for the modem
The LAN adapter and modem cannot be configured for the same
interrupt. Either select a different modem interrupt (using the COMIRQ
keyword or a different COM port value), or select a different LAN
interrupt (using the INTERRUPT keyword).
The COMBASE keyword is required in this configuration
If the COMIRQ keyword has been specified, but COM1, COM2, COM3,
or COM4 has NOT been specified, the COMBASE keyword must be
specified with an appropriate value.
The COMIRQ keyword is required in this configuration
If the COMBASE keyword has been specified, but COM1, COM2,
COM3, or COM4 has NOT been specified, the COMIRQ keyword must
be specified with an appropriate value.
The Network Controller is not responding
A PRO/100 PC Card was detected, but subsequent attempts to initialize
the network controller failed. Try setting the WORDSIZE parameter to 8.
Please specify a decimal number for the INTERRUPT keyword
This message applies only to the NDIS 2.0 Driver. The value specified
under the INTERRUPT keyword in the PROTOCOL.INI file must be a
decimal not a hexadecimal number.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-49
Please specify a hexadecimal number for the IOADDRESS keyword
This message applies only to the NDIS 2.0 Driver. The value specified
under the IOADDRESS keyword in the PROTOCOL.INI file must be a
hexadecimal number.
Please specify a hexadecimal number for the MEMORY keyword
This message applies only to the NDIS 2.0 Driver. The value specified
under the MEMORY keyword in the PROTOCOL.INI file must be a
hexadecimal number.
Please specify either 8 or 16 for the WORDSIZE keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the WORDSIZE keyword in the NET.CFG or
PROTOCOL.INI file must be either 8 or 16.
Please specify a nonzero decimal number for the SOCKET keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the SOCKET keyword in the NET.CFG or
PROTOCOL.INI file must be a decimal number other than zero.
Please specify 0, 1, 2, or 3 for the MEMWAITSTATES keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the MEMWAITSTATES keyword in the NET.CFG or
PROTOCOL.INI file must be either 0, 1, 2, or 3.
Please specify 0, 1, 2, or 3 for the IOWAITSTATES keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the IOWAITSTATES keyword in the NET.CFG or
PROTOCOL.INI file must be either 0, 1, 2, or 3.
The memory test failed - Please select a different memory address
The memory test will write data into the memory, read them back, and
verify if they are the same. In this case, the memory written and read back
were found to be different.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-50 PRO/100 LAN+Modem PC Card User’s Guide
The I/O test failed - Please select a different I/O address
The driver failed the I/O test. Try a different I/O address.
The IRQ test failed - Please select a different IRQ
The driver failed the IRQ test. Try a different IRQ address.
Please specify either IO or MEM for the MODE keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the MODE keyword in the NET.CFG or
PROTOCOL.INI file must be either IO or MEM.
Please specify a decimal number for the COMIRQ keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the COMIRQ keyword in the NET.CFG or
PROTOCOL.INI file must be a decimal number.
Please specify a hexadecimal number ending in 8 for the
COMBASE keyword
This message applies to both the ODI and NDIS 2.0 drivers. The value
specified under the COMBASE keyword in the NET.CFG or
PROTOCOL.INI file must be a hexadecimal number in the range 248 to
3F8.
No standard COM ports available. Please use custom COM port
(COMIRQ, COMBASE)
This message applies to both the ODI and NDIS 2.0 drivers. All COM
ports (COM1 - COM4) are being used. Create a custom COM port by
adding the COMIRQ and COMBASE keywords, with assigned values, to
the NET.CFG or PROTOCOL.INI file.
The selected COM IRQ is in use by another device
The IRQ value set for the COM port is already in use by another device.
Assign a different IRQ value for the COM port.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-51
The selected COM port already exists
The COM port is already in use by another device. Assign a different I/O
port for the COM port.
Windows 3.x Troubleshooting
Important
For application notes covering installation and configuration
issues pertaining to specific computers, Card and Socket
Services, and communications software packages, see Chapter 5.
Utilities and Applications.
A driver failed to load, and I’m using Card
and Socket Services
Card and Socket Services are a set of drivers designed to support the PC
Card (PCMCIA) standard. These drivers are generally supplied by the
computer manufacturer. Among other functions they
• Hide the PCMCIA socket hardware implementation from the PRO/
100 PC Card driver.
• Control the allocation of resources (memory windows, I/O ports,
interrupts) to the PRO/100 PC Card.
Recommendations for Use of Card and Socket Ser-
vices with the PRO/100 PC Card.
A. If the memory manager EMM386.EXE is being used, verify that the
memory required for the PRO/100 PC Card has been excluded from use
by the memory manager in the CONFIG.SYS. The memory exclusion
required when using Card and Socket Services is generally larger than the
exclusion needed by the
PRO/100 PC Card alone. The safest setting when troubleshooting is to
“remark out” the entire “C” and “D” memory ranges, as follows:
DEVICE=C:\PATH\EMM386.EXE NOEMS X=C000-DFFF
Download from Www.Somanuals.com. All Manuals Search And Download.
4-52 PRO/100 LAN+Modem PC Card User’s Guide
After the driver has been successfully loaded, the memory exclusion may
be reduced through trial and error or in accordance with the Card and
Socket Services documentation. The system must be rebooted before the
revised settings take effect.
B. When the PRO/100 PC Card driver is loaded it either reads a configu-
ration file or uses command line parameters to determine which resources
it should use. The following is a list of driver types, driver file names, and
the configuration method used by each:
Type File Name
ODI M16BODI.COM reads NET.CFG configuration file
NDIS2 M16BNDIS.EXE reads PROTOCOL.INI configuration file
Packet M16BPD.EXE uses COMMAND LINE parameters
Test M16BTEST.EXE uses COMMAND LINE parameters
Configuration Method
C. Card and Socket Services will generally try to assign a set of resources
(interrupt, memory window, I/O window) to the PRO/100 PC Card. The
resources configured for the PRO/100 PC Card (in a configuration file or
on a command line) must match the resources assigned by Card and
Socket Services. If they do not, the driver will generally fail to load.
The way resources are assigned to the PC Card varies among Card and
Socket Services manufacturers. The following section provides guidelines
for the most popular Card and Socket Services. Review your Card and
Socket Services documentation. To use Card and Socket Services with the
PRO/100 PC Card, you must know what resources will be assigned by
Card and Socket Services, then specify the same resources when configur-
ing the PRO/100.
IBM
The following are the files generally loaded with IBM Card and Socket
Services.
DEVICE=C:\THINKPAD\IBMDSS01.SYS /S0=2
DEVICE=C:\THINKPAD\IBMDOSCS.SYS
DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF (/MA SHOULD
MATCH THE EMM386 EXCLUSION)
DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI (CALLED
A “GENERIC” CARD DRIVER)
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-53
The AUTODRV.INI file is used to assign resources to the PRO/100 PC
Card. The AUTODRV.INI file should be edited to read as follows:
ETHERNET.
CARDID=ETHER,CREDI
;OPTION=IGNORE (THE SEMICOLON IS REQUIRED)
PORT1=320, IRQ=5, MEMORY1=C800, WAITSTATE=1
The same resources should be specified in the PRO/100 PC Card driver
initialization file.
Phoenix
The Phoenix Card and Socket Services super client driver PCMSCD.EXE
should NOT be configured with the PCM.EXE program to support the
PRO/100 PC Card. Use the default setup and the following sequence of
commands in your CONFIG.SYS file.
DEVICE=C:\PCMPLUS3\PCMSS.EXE
DEVICE=C:\PCMPLUS3\PCMCS.EXE
DEVICE=C:\PCMPLUS3\PCMRMAN.SYS
DEVICE=C:\PMCPLUS3\PCMSCD.EXE (CALLED A “GENERIC” CARD DRIVER)
Be sure to verify that an EMM386 memory exclusion has been stated to
cover the region where the Intel card loads.
SystemSoft
The SystemSoft’s CardSoft Card and Socket Services are loaded in the
CONFIG.SYS file and generally include the following lines:
DEVICE=C:\CARDSOFT\SOCKET_SERVICES_DRIVER
(THIS FILE VARIES
BY MACHINE TYPE)
DEVICE=C:\CARDSOFT\CS.EXE
DEVICE=C:\CARDSOFT\CSALLOC.EXE C:\CARDSOFT\CSALLOC.INI
DEVICE=C:\CARDSOFT\CARDID.EXE (CALLED A “GENERIC” CARD DRIVER)
Resources assigned by CardSoft Card and Socket Services are controlled
by the files CSALLOC.INI and CARDID.INI. CSALLOC.INI contains a
list of resources available to Card and Socket Services. CARDID.INI
controls how resources will be assigned to specific types of cards. The
setting in the PRO/100 PC Card driver configuration file should match
Download from Www.Somanuals.com. All Manuals Search And Download.
4-54 PRO/100 LAN+Modem PC Card User’s Guide
the resources assigned by the LAN1xxxxxx keywords in the CARDID.INI
file. The LAN1MEMORYBASE2 entry can be ignored.
A driver failed to load, and I’m NOT using
Card and Socket Services
A. Verify that a block of memory for use by the PRO/100 PC Card has
been excluded from any memory manager being loaded. Memory manag-
ers are generally loaded in the CONFIG.SYS. The following example is
given for EMM386.EXE and a PRO/100 PC Card loading at its default
memory address of D2000:
DEVICE=C:\PATH\EMM386.EXE NOEMS X=D200-D3FF
B. Verify that power management has been disabled and the PCMCIA
socket is powered/enabled in the computer system’s CMOS setup. These
settings may not be present in all machines. Consult your computer
documentation for information on how to access and modify the system
setup.
C. Reboot the machine by turning off the power and turning it back on
again (cold boot). If the driver still fails to load, the cause is generally a
resource conflict. Common causes of resource conflicts include sound
systems, other PCMCIA adapters, and built in ROMs. The resources
required for a PRO/100 PC Card include a memory window (MEM
keyword), a LAN interrupt (INT keyword, and an I/O address
(IOADDRESS keyword). The default settings are indicated below.
Review your computer documentation to determine what resources are
available, or use a trial and error approach. The table below shows a
suggested trial and error sequence. If you use this method, be sure to add a
memory exclusion from C000-DFFF to the EMM386 line until a suitable
memory location has been found. Then the memory exclusion can be
reduced to an 8K window. Perform a cold boot between each trial to
ensure that the PRO/100 PC Card and PC Card sockets are completely
reset.
When the PRO/100 PC Card driver is loaded it either reads a configura-
tion file or uses command line parameters to determine which resources it
should use. The following is a list of driver types, driver file names, and
the configuration method used by each:
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-55
Type File Name
ODI
NDIS2 M16BNDIS.EXE reads PROTOCOL.INI configuration file
Packet M16BPD.EXE uses COMMAND LINE parameters
Test M16BTEST.EXE uses COMMAND LINE parameters
Configuration Method
M16BODI.COM reads NET.CFG configuration file
The default resources used by the PRO/100 PC Card when no other
setting is stated are:
MEMORY
AUTO
AUTO
AUTO
AUTO
IRQ
IOADDRESS (NDIS)
PORT (ODI)
Troubleshooting combinations for driver configuration without Card and
Socket Services:
TRIAL
MEM
D2000
CC000
D2000
CC000
D2000
CC000
D2000
CC000
D2000
CC000
D2000
CC000
D2000
CC000
D2000
D2000
INT
5
IOADDRESS WORDSIZE
Default
320
320
320
320
320
320
320
320
340
340
340
340
340
340
340
340
16
16
16
16
16
16
16
16
8
1
5
2
10
10
11
11
15
15
5
3
4
5
6
7
8
9
5
8
10
11
12
13
14
15
10
10
11
11
15
15
8
8
8
8
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4-56 PRO/100 LAN+Modem PC Card User’s Guide
If none of the above settings allows the driver to load, it may be necessary
to add an IOWAITSTATES=2 and MEMWAITSTATES=2 parameter to
the appropriate PRO/100 PC Card driver configuration file or command
line.
D. If the driver still fails to load after you’ve tried the combinations above,
your machine may require the use of Card and Socket Services. See the
preceding section.
E. Machine-specific notes:
IBM 755, 360, 355 - Set the keyword WORDSIZE=8 in your configura-
tion file or on the command line (WORDSIZE 8 for the ODI driver).
The driver loaded successfully, but I can’t
get on the network
A. Check all connections and verify that the cable drop is good (try a cable
that is known to work on another workstation).
B. Reboot by powering down the machine (cold boot). On some ma-
chines the PC Card controller chipset is not properly reset on a warm
boot, and this can cause network errors.
C. In a NetWare environment, verify that the frame type running on your
network server is the same as the FRAME type listed first in the
NET.CFG. If you are not sure what the correct Ethernet frame type is,
check with your system administrator. On a multi-server network, add a
preferred server statement to the NET.CFG.
D. There could be an interrupt conflict. Try loading the driver with a
different interrupt specified in the PRO/100 PC Card configuration file.
(This may also require some re-configuration of Card and Socket Services,
if they’re being used.)
E. If the problem persists, and you’re on a 10BASE-T network, try
patching directly into the hub. If the adapter works when plugged directly
into the hub, but not when attached via a longer cable run, verify that the
cable run length is within the IEEE 10BASE-T specification (100 meters).
If the cable length is correct, the adapter may be defective. Contact Intel
Customer Support.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-57
The driver loaded, but my DOS modem
software won’t work
The PRO/100 PC Card is configured to add a second interrupt and I/O
address window in order to emulate a standard serial port interface. Use
the COMx keyword in your driver configuration file or as a command line
parameter to enable serial port emulation. If no COMx keyword is used,
the Intel driver will configure the PRO/100 PC Card at the first available
COM port.
Pre-set default resources corresponding to the COM port value are used,
as follows:
PORT IRQ
IOADDRESS
03F8
COM1
COM2
COM3
COM4
4
3
4
3
02F8
03E8
02E8
The default setting for the COM port address can be changed by the
COMBASE keyword. The default setting for the IRQ can be changed by
the COMIRQ keyword. A second keyword that affects interrupt usage is
SHAREIRQ. The SHAREIRQ keyword forces the modem side to share
the interrupt that the network side is using. The INT or INTERRUPT
keyword is used to set the interrupt the network side uses. Card and
Socket Services also has an effect on interrupt usage.
To troubleshoot the issues described above, proceed as follows:
1 Verify that the phone line is an analog phone line (the type used
with other modems and fax machines). Connecting the PRO/100
PC Card to a digital phone line will not damage the adapter, but is
not recommended.
2 Verify that the COMx keyword is present in the driver configuration
file or as a command line parameter as appropriate.
3 Observe the COM port number stated when the driver loads. It
should match the value of x assigned to the COMx keyword
(decimal values or 1, 2, 3, or 4) in the driver configuration file
(NET.CFG for M16BODI, PROTOCOL.INI for M16BNDIS) or
as a command line parameter for the packet driver (M16BPD) or
Download from Www.Somanuals.com. All Manuals Search And Download.
4-58 PRO/100 LAN+Modem PC Card User’s Guide
modem driver (IMENABLE). If they do not match, either there are
multiple COMx keywords listed in the file or there are multiple
configuration files.
4 Run Microsoft Diagnostics (MSD) and see if the COM port shows
up. On some machines MSD will not show what COM port was
configured for the PRO/100 PC Card. If it doesn’t, try the
following command:
ECHO ATDTNNNNNNN > COMX:
where nnnnnnn is a telephone you can hear ring, and x is the COM
port number. If the phone rings, this indicates that the COM port is
correctly configured and that the modem is able to dial.
5
If the COM port does not show up after running MSD, try
changing the x the COMx keyword to a different port value (start
with COM4 and try each value in sequence through COM1). Power
down the computer between trials.
The modem works in DOS, but not in
Windows
A. Verify that there are no communications/fax programs automatically
loading on Windows startup or running in the background.
B. If you are using Card and Socket Services, try the following:
1 In Windows, select Control Panel, Ports, and under Advanced, set
the selected COM port IOADDRESS to default, set the INTER-
RUPT LEVEL to the value specified by the INT or INTERRUPT
keyword in the LAN configuration file. You should also modify the
SYSTEM.INI file as follows: set COMxIRQ=y, where x is the
COM port the PRO/100 PC Card is configured as, and y is the
interrupt the LAN driver is using (as stated in the NET.CFG or
PROTOCOL.INI file).
2 If you are using the M16BODI driver and you receive a blue
warning screen stating that “A hardware interrupt has occurred,” try
adding the following section to the SYSTEM.INI file:
[VIPX]
VIRTUALIZE IRQX = OFF
where x is the interrupt number (in hexadecimal notation) used by
the M16BODI driver.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-59
3 Turn computer power off and then on again (cold boot).
4 Start the Windows Terminal program in the Accessories group.
Select a COM port under the setting/communications options, click
OK to get back to the terminal screen. Change to modem command
mode and type AT, then press enter. If the modem responds with
OK, the trial configuration was correct.
5 In some cases an interrupt conflict will not be apparent until a
Windows mouse driver is loaded. It will then be necessary to cold
boot the machine, load the PRO/100 PC Card driver and re-start at
step 1. above.
C. Try disabling Card and Socket Services if they are enabled (see Item 2
of these Symptoms and Solutions).
D. If you are NOT using Card and Socket Services, try the following:
1 Verify the following entries in the Windows SYSTEM.INI file:
BOOT.
COMM.DRV=COMM.DRV
386ENH.
DEVICE=*VCD
You may need to remark out any *VCD.386 added by other
programs (IBMVCD.386, PCMVCD.386, SSVCD.386).
2 In Windows, go into the Control Panel, then Ports, and under the
Advanced options, set the selected COM port IOADDRESS and
INTERRUPT to default settings.
3 Exit Windows and turn computer off and on again (cold boot).
4 Start the Windows Terminal program in the Accessories group.
Select a COM port under the setting/communications options, click
OK to get back to the terminal screen. Change to modem command
mode and type AT, then press enter. If the modem responds with
OK, the trial configuration was correct.
5 In some cases an interrupt conflict will not be apparent until a
Windows mouse driver is loaded. It will then be necessary to cold
boot the machine, load the PRO/100 PC Card driver and re-start at
step 1. above.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-60 PRO/100 LAN+Modem PC Card User’s Guide
I can't hear the modem
A. Be sure the computer speaker is enabled in the computer’s CMOS
setup utility.
B. To enable modem sound, include the following AT command in any
communications package modem initialization string:
M1
or as a standalone command preceded by the letters AT:
ATM1
The PRO/100 PC Card does not have a built-in speaker. It relies on the
PC Card software to direct signals to the computer’s speaker. A few
computers do not properly direct the PRO/100 PC Card audio to the
system speaker. The modem will connect and operate normally, but no
sound will be heard. On some PCs you can set the speaker on or off or
change volume levels with a keyboard sequence. See your computer
documentation.
Computer-Specific Application Notes
(Windows 3.x)
If you are using Card and Socket Services and are experiencing problems,
find your computer in the list below and review the information provided.
The examples of Card and Socket Services driver stacks and
EMM386.EXE lines have been verified and are known to be reliable.
Sample Card and Socket Services configuration files and their known
problems are also supplied.
Ambra
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DCFF
DEVICE=C:\PCM3\CNFIGNAM.EXE /DEFAULT
DEVICE=C:\PCM3\PCMSS.EXE
DEVICE=C:\PCM3\PCMCS.EXE
DEVICE=C:\PCM3\PCMRMAN.SYS
DEVICE=C:\PCM3\PCMSCD.EXE
REM DEVICE=C:\PCM3\PCMATA.SYS
REM DEVICE=C:\PCM3\PCMFFCS.EXE
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-61
REM DEVICE=C:\PCM3\DBLFALSH.EXE
REM DEVICE=C:\PCM3\MS-FLASH.SYS
The configuration above will work with the PRO/100 PC Card driver at
memory location D8000.
AST Power Exec
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF
DEVICE=C:\CARDSOFT\SS365SL.EXE
DEVICE=C:\CARDOSFT\CS.EXE
DEVICE=C:\CARDSOFT\CSALLOC.EXE
REM DEVICE=C:\CARDSOFT\ATADRV.EXE
REM DEVICE=C:\CARDSOFT\MTSRAM.EXE
REM DEVICE=C:\CARDSOFT\MTDDRV.EXE
DEVICE=C:\CARDSOFT\CARDID.EXE
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Austin Notebooks series
DEVICE=C:\DOS\EMM386.EXE X=D000-D7FF
DEVICE=C:\PCMCIA\CARDSOCK.SYS /IO:240
DEVICE=C:\PCMCIA\CTALKCS.EXE
DEVICE=C:\PCMCIA\CARDTALK.SYS /A /IOW=320-31F /MEMW=D000-D7FF
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Compaq Contura Aero
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D5FF
DEVICE=C:\CPQDOS\SSVLSI.EXE
DEVICE=C:\CPQDOS\CS.EXE
DEVICE=C:\CPQDOS\CSALLOC.EXE C:\CPQDOS\CSALLOC.INI
REM DEVICE=C:\CPQDOS\ATADRV.EXE
DEVICE=C:\CPQDOS\CARDID.EXE C:\CPQDOS\CARDID.INI
REM DEVICE=C:\CPQDOS\MEMDRV.EXE
REM DEVICE=C:\CPQDOS\DBLFLASH.EXE
Download from Www.Somanuals.com. All Manuals Search And Download.
4-62 PRO/100 LAN+Modem PC Card User’s Guide
REM DEVICE=C:\CPQDOS\MS-FLASH.SYS
The above configuration uses only the drivers necessary for the Intel
adapter. This configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Compaq LTE Elite models
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF
DEVICE=C:\CPQDOS\SSVLSI.EXE
DEVICE=C:\CPQDOS\CS.EXE
DEVICE=C:\CPQDOS\CSALLOC.EXE C:\CPQDOS\CSALLOC.INI
DEVICE=C:\CPQDOS\ATADRV.EXE
DEVICE=C:\CPQDOS\CARDID.EXE C:\CPQDOS\CARDID.INI
DEVICE=C:\CPQDOS\MEMDRV.EXE
DEVICE=C:\CPQDOS\DBLFLASH.EXE
DEVICE=C:\CPQDOS\MS-FLASH.SYS
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Dell Latitude XP series
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DBFF
DEVICE=C:\CARDSOFT\SSVADEM.EXE
DEVICE=C:\CARDOSFT\CS.EXE
DEVICE=C:\CARDSOFT\CSALLOC.EXE
REM DEVICE=C:\CARDSOFT\ATADRV.EXE
REM DEVICE=C:\CARDSOFT\MTSRAM.EXE
REM DEVICE=C:\CARDSOFT\MTDDRV.EXE
DEVICE=C:\CARDSOFT\CARDID.EXE
INSTALL=C:\CARDSOFT\CS_APM.EXE
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-63
Gateway ColorBook series
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF
DEVICE=C:\CARDSOFT\SSCIRRUS.EXE
DEVICE=C:\CARDOSFT\CS.EXE
DEVICE=C:\CARDSOFT\CSALLOC.EXE
REM DEVICE=C:\CARDSOFT\ATADRV.EXE
REM DEVICE=C:\CARDSOFT\MTSRAM.EXE
REM DEVICE=C:\CARDSOFT\MTDDRV.EXE
DEVICE=C:\CARDSOFT\CARDID.EXE
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
IBM ThinkPad 350, 755CS
DEVICE=C:\DOS\EMM386.EXE X=C800-CFFF
The switch X=C800-CFFF on the EMM386 line must be used with the
configuration below.
DEVICE=C:\THINKPAD\IBMDSS01.SYS
DEVICE=C:\THINKPAD\IBMDOSCS.SYS
DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF
DEVICE=C:\THINKPAD\$ICPMDOS.SYS
REM DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI
The above line has been changed to prevent AUTODRV.SYS from
loading. The above configuration will work with the PRO/100 PC Card
driver at memory location C8000.
IBM ThinkPad 360CS
DEVICE=C:\DOS\EMM386.EXE X=C800-CFFF
The switch X=C800-CFFF on the EMM386 line must be used with the
configuration below.
DEVICE=C:\THINKPAD\IBMDSS01.SYS
DEVICE=C:\THINKPAD\IBMDOSCS.SYS
DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF
DEVICE=C:\THINKPAD\$ICPMDOS.SYS
DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI
Download from Www.Somanuals.com. All Manuals Search And Download.
4-64 PRO/100 LAN+Modem PC Card User’s Guide
The above configuration will work with the PRO/100 PC Card driver at
memory location C8000.
IBM ThinkPad 750CS
DEVICE=C:\DOS\EMM386.EXE X=B000-BFFF X=C800-CFFF
The switch X=C800-CFFF on the EMM386 line must be used with the
configuration below.
DEVICE=C:\THINKPAD\IBMDSS01.SYS /S0=2
DEVICE=C:\THINKPAD\IBMDOSCS.SYS
DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF
DEVICE=C:\THINKPAD\$ICPMDOS.SYS
DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI
REM DEVICE=C:\IBMAUDIO\AUDIODD\TPAUDDD.SYS
The above line must be remarked out if the Thinkpad 750 series has a
built in sound card. The above configuration will work with the PRO/100
PC Card driver at memory location C8000.
NEC Versa models
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF
DEVICE=C:\CARDSOFT\SSCIRRUS.EXE
DEVICE=C:\CARDSOFT\CS.EXE
DEVICE=C:\CARDSOFT\CSALLOC.EXE C:\CARDSOFT\CSALLOC.INI
REM DEVICE=C:\CARDSOFT\ATADRV.EXE
REM DEVICE=C:\CARDSOFT\CARDID.EXE C:\CARDSOFT\CARDID.INI
REM DEVICE=C:\CARDSOFT\MEMDRV.EXE
REM DEVICE=C:\CARDSOFT\DBLFLASH.EXE
REM DEVICE=C:\CARDSOFT\MS-FLASH.SYS
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Sharp 8650
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF
DEVICE=C:\CARDTALK\ARIMASS.SYS
DEVICE=C:\CARDTALK\CTALKCS.EXE
DEVICE=C:\CARDTALK\CARDTALK.SYS /A
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 3.x/MS-DOS Installation 4-65
The above configuration will work with the PRO/100 PC Card driver at
memory location D2000.
Toshiba 19xx, 47xx, 48xx series
DEVICE=C:\DOS\EMM386.EXE NOEMS X=C800-CFFF
DEVICE=C:\PCMPLUS3\CNFIGNAM.EXE /DEFAULT
DEVICE=C:\PCMPLUS3\PCMSS.EXE
DEVICE=C:\PCMPLUS3\PCMCS.EXE
DEVICE=C:\PCMPLUS3\PCMRMAN.SYS
DEVICE=C:\PCMPLUS3\PCMSCD.EXE
The above configuration will work with the PRO/100 PC Card driver at
memory location C8000.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-66 PRO/100 LAN+Modem PC Card User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
Utilities and Applications
This chapter describes software utilities provided with the PRO/100 PC
Card and provides configuration guidelines for popular communications
applications to be used with the Intel modem.
UTILITIES
Intel provides several utilities with the PRO/100 PC Card that run under
Microsoft Windows or MS-DOS. The utilities are:
• Country Identifier Utility (Windows 95, NT, 3.x)
• Modem Test (Windows 95, NT, 3.x)
• Diagnostic Test (MS-DOS prompt required)
• Modem COM Port Monitor (Windows 3.x only)
The Windows utilities described in this chapter are automatically copied to
your hard drive and launched during installation of the PRO/100 PC Card
under Windows 95 and Windows NT version 4.0, or when you run the
Intel Installation Program under Windows 3.1 or 3.11. Icons for these
utilities are also installed in the Windows program group set up at the time
of installation.
Country Identifier Utility
The Country Identifier utility is a Windows-based utility that enables the
PRO/100 PC Card user to select a “country of installation” setting for
modem communications. This setting enables the modem to function in
accordance with the configuration requirements of a specific country.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2 PRO/100 LAN+Modem PC Card User’s Guide
How to Use Country Identifier
The country identifier utility is automatically copied to your hard drive and
launched during installation of the PRO/100 PC Card under Windows 95
and Windows NT version 4.0, or when you run the Intel Installation
Program under Windows 3.1 or 3.11. An icon for Country Identifier is
also installed in the Windows program group so that the utility can be re-
run if the country settings needs to be changed.
Follow the steps below to run Country Identifier from the Intel
program group if you need to modify the country setting chosen
during the installation process.
1 Launch Country Identifier through Windows. Either double-click
the Country Identifier icon in the PRO/100 program group, or use
the Windows File/Run command sequence and type
[path]TELSEL.EXE in the Command Line box, where [path]
indicates the location of the Country Identifier utility on your hard
drive.
2 The current country setting is listed at the top of the screen, and the
other countries supported are listed below. To change to a different
country, locate the country on the list and double click. The
application will verify that the country setting has been changed.
3 Click on Exit to close the program.
Modem Test Utility
The Intel Modem Test utility indicates the status of the COM ports on
your computer, including which COM port the Intel modem is configured
to use. The icon for this program will be installed in the PRO/100
program group at installation. Double-click the icon to run the Modem
Test utility.
If a Intel modem is enabled, the Modem Test utility can also be used as a
terminal program to input AT commands to the modem without the use
of other communications software. Click the Terminal button on the
Modem Test screen to open a window for input of modem commands.
See Chapter 6. Modem Reference for a complete list of modem
commands supported by the PRO/100 PC Card.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-3
Diagnostic Test Utility (M16BTEST.EXE)
Intel provides a DOS-based self test diagnostics program. This program,
located on PRO/100 PC Card Disk 2, Network Drivers Disk, tests several
adapter functions. It also reports test results, the serial number of the unit,
and the node (or Ethernet) address.
M16BTEST can only be run from an MS-DOS command line. Under
Windows 95 and Windows NT, power down the computer perform a
clean boot to the MS-DOS prompt (under Windows 95 press Shift+F5 at
the message Starting Windows 95 . . . ).
The M16BTEST utility is intended to be a diagnostic tool for trouble-
shooting configuration errors. Cards can be inserted and removed at any
time. Multiple cards and different configurations can be tested.
Executing the Self Test
Use the following steps to execute the self test.
1 Install the PRO/100 PC Card according to the instructions for your
operating system.
2 Power down and restart the computer from MS-DOS (use Shift+F5
in Windows 95). DO NOT load a network driver.
Note
Do not run M16BTEST with a network driver loaded. Loading a
network driver before running M16BTEST may cause unpredict-
able results when exiting the test utility.
3 Run the diagnostic test by typing [path]M16BTEST at the MS-
DOS prompt, then press Enter. [path] can be either
C:\INTEL\M16B\M16BTEST or A:\M16BTEST.
Note
If an error message displays when you execute the self test, see
“Error Messages for Windows 3.x and MS-DOS Drivers” in
Chapter 4. Windows 3.x/MS-DOS Installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4 PRO/100 LAN+Modem PC Card User’s Guide
Main Screen
The program consists of several function “buttons” and a view pane.
Pressing or invoking a function will bring up the corresponding screen in
the view pane. This view remains until another is selected. To exit
M16BTEST type 'x' or push the 'Exit' button.
When a function is active, the button appears to remain down or pushed.
Once the button pops up, the function is completed and the screen is a
passive results display.
There are nine functions which can be invoked by pushing the associated
button on the main screen. A button can be pushed by pressing the
highlighted letter indicated on the button, or by using the left mouse
button. Each function is explained below.
TEST
This function uses the current configuration to initialize the adapter and
verify it is powered on and properly seated in its slot. It displays the
current setting and test result for each parameter. Parameters are config-
ured through the CONFIGURE function described below. If a card is
detected and initialized successfully, the CIS information is displayed.
A failure may indicate that service is required for the PRO/100 PC Card.
Contact Intel Customer Support.
The CIS section displays the serial number of the unit, its manufacturing
date, and its network node address. This data has been preprogrammed at
the factory and cannot be altered.
CONFIGURE
This function allows the user to set the parameters used for testing. The
address mode can be set to Auto, Memory, or I/O. For Memory and I/O
a hexadecimal address can be specified. The IRQ can be set to Auto, or
IRQ. The IRQ selection can be used to force a particular interrupt. The
network line speed and line mode can also be set from this function.
SOFTWARE
This function attempts to determine what software is currently loaded that
could affect the operation of the card. It displays the current version of
MS-DOS and Windows, and any Card and Socket Services available
(under Windows 3.x or MS-DOS).
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-5
HARDWARE
This function attempts to determine if a PCMCIA controller exists on the
machine. It first checks for PCI BIOS extensions, and then it searches for
any PCMCIA controllers. If found it displays controller type, base I/O
address, offset, number of the socket in which the PRO/100 is installed,
and the PCI interrupt (if enabled by the BIOS).
NETWORK
This function enables the card on the Ethernet network and performs
some diagnostics. It reports the operating mode and speed detected and
monitors the network for traffic. Network traffic is shown on a graph.
This graph provides a visual representation of the volume of traffic on the
local area network (LAN). The Receive Statistics window displays the
cumulative totals for received Packets, KBytes, and Errors.
RESOURCES
This function attempts to determine free resources that are available for
use by the driver. It searches for memory, I/O, and IRQ.
ADVANCED
This function allows the user to set up advanced diagnostics.
ABOUT
This function displays the current version of the diagnostic program.
HELP
This function displays the help screen.
EXIT
This function exits the application.
COM port monitor (Windows 3.x only)
The Intel COM Port Monitor is an onscreen LED program that runs
under Microsoft Windows 3.1 and 3.11, and Windows for Workgroups
3.11. The program provides a simulated onscreen display of modem status
LEDs such as those found on external modems.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-6 PRO/100 LAN+Modem PC Card User’s Guide
How to Use the COM port monitor
To launch the COM port monitor, double-click on the the COM port
monitor icon in the Intel PRO/100 program group. The COM port
monitor window will be present on the desktop and within applications,
and can be moved by dragging it with the mouse.
COM port monitor is configurable with COM ports 1-4. To configure
with a specific COM port, click once on the COM port monitor window,
and a dialog box will appear. Select a COM port and click OK.
The COM port monitor window contains the following LEDs:
Tx
Transmit
Rx
Receive
CTS
CD
RI
Clear to Send
Carrier Detect
Ring Indication
To exit the COM port monitor program, Shift+Click on the COM port
monitor window, or click on the window to open the dialog box, then
click on the EXIT button.
Communications Application Notes and
Modem Script Files
Note
The modem script files mentioned in this document are
intended to be used if you have tried a generic Hayes or
Microcom configuration without success. The files referred to in
the application notes are available on disk 2, Network Drivers
Disk, in the \scripts directory.
This section contains instructions for setting up your PRO/100 PC Card
with several popular communications programs.
The following applications are covered in this section:
• America Online v. 3.0
• America Online v. 3.0 with Windows 95
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-7
• CompuServe - WinCIM 2.5.1 with Internet Explorer 2.1
• CompuServe - WinCIM v.3.02 with Windows 95
• Laplink v.6.0
• Laplink v.6.0 with Windows 95
• Lotus CC:Mail Mobile v.2.22 with Windows
• Lotus CC:Mail Mobile v.2.22 with Windows 95
• Lotus Notes v.4.11a with Windows
• Lotus Notes v.4.11a with Windows 95, NT 4.0
• Microsoft Dial-Up Adapter Networking for Windows 95
• Microsoft Remote Access Server (RAS)
• Prodigy Internet v.1.1.6 with Windows 95
Introduction
Some of the instructions include references to modem script files. The
following files are contained in the \scripts directory on disk 2:
• CLASS73.MDM
• MODEM.INI
• M16BRAS1.INF
• M16BMSM.SCR
• M16BMSM.MDM
• M16BLOT.MDM
Modem Setup with a Communications Program
Most communications programs include a modem setup function or will
autodetect the modem using a sequence of steps like the following:
1 Search for modem
2 Determine manufacturer, model, speed, communications port, and
interrupt
3 Incorporate modem configuration into program
If the Intel modem is installed before the communications program is,
the Intel modem will be automatically configured by the communications
program.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-8 PRO/100 LAN+Modem PC Card User’s Guide
If the communications program is already installed, you are installing a
new modem, or your modem is not functioning, follow the instructions
for your application.
Modem Setup After Windows 95 Installation
1 Install the PRO/100 PC Card according to the instructions in
Chapter 2. Windows 95 Installation.
2 Verify modem settings as follows:
a Go to Control Panel.
b Double-click the Modem icon.
c Highlight the EtherExpress PRO/100 LAN+Modem PC Card.
d Click Properties.
e Note the Communications Port assigned to the Intel adapter
under the General tab.
f
Accept the default or set the Maximum Speed of the modem.
g Use the default initialization string or modify it by clicking the
Connection Tab, then Advanced, and inputting changes on the
Extra Settings line.
3 Verify that the modem is functioning via Modem Diagnostics and
Hyperterminal.
4 Install the communications program. The Intel modem is automati-
cally configured by the communications program, if the modem is
installed prior to the communications program. During the installa-
tion process, you will be prompted to verify the Modem selection,
communications port, etc.
America Online version 3.0
America Online v.3.0 ships with a MODEM.INI file. This file must be
modified in order to use the EtherExpress PRO/100 LAN+Modem PC
Card.
1 To update the MODEM.INI file, do the following:
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-9
a In the C:\AOL30\MPM sub-directory,
b Rename the CLASS73.MDM file to CLASS73.OLD and
MODEM.INI file to MODEM.OLD.
c Copy the new CLASS73.MDM and MODEM.INI files to the
C:\AOL30\MPM sub-directory.
d Start the America Online program.
2 To set up the PRO/100 PC Card, click SETUP on the Welcome
screen.
a Click Modem Setup in the Network & Modem Setup window.
b In the Modem Selection and Customization window.
• Select the COM port that is assigned to the Intel PRO/100
modem under Modem Port.
• Highlight "EtherExpress PRO/100 LAN+Modem PC Card,"
then click OK.
• Note: Use the default initialization string. If you need to change
the string, you may do so under the Edit Commands options.
America Online version 3.0 with Windows 95
America Online v.3.0 ships with a MODEM.INI file. This file must be
modified in order to use the EtherExpress PRO/100 LAN+Modem PC
Card.
1 To update the MODEM.INI file, proceed as follows:
a In the C:\AOL30\MPM sub-directory,
b Rename the CLASS73.MDM file to CLASS73.OLD and
MODEM.INI file to MODEM.OLD.
c Copy the new CLASS73.MDM and MODEM.INI files to the
C:\AOL30\MPM sub-directory.
d Start the America Online program.
2 To set up your Intel product, click SETUP on the Welcome screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-10 PRO/100 LAN+Modem PC Card User’s Guide
a Click Modem Setup in the Network & Modem Setup window.
b In the Modem Selection and Customization window.
• Select the COM # that is assigned to the Intel modem under
Modem Port.
• Highlight "EtherExpress PRO/100 LAN+Modem PC Card,"
then click OK.
• Note: Use the default initialization string. If you need to change
the string, you may do so under the Edit Commands options.
CompuServe WINCIM version 2.5.1 with Internet Ex-
plorer version 2.1
To set up the Intel modem or modify the present configuration:
1 Click Special.
2 Click Session Settings.
a Indicate which COM port is assigned to the Intel modem under
Connector.
b Select the speed of the Intel modem under Baud Rate.
c Click once in the box to the left of Use Winsock, for Internet
access.
3 Click Modem in the Setup Session Settings window.
a In the Modem Current Settings window, select "Other" under
Modem.
b Use the default initialization string. If modification is required,
enter the necessary changes in the Initialize: section.
c Click OK, to update configuration and close menus.
CompuServe WINCIM version 3.02 with Windows 95
To set up the Intel modem or modify the present configuration:
1 Click Access or the Setup icon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-11
2 Click Preferences.
3 In the Connection window under Connection Type check all
settings for accuracy.
a Winsock: (Default WINSOCK).
b Connect using:
c Phone #:
d Port:
e Port speed:
f
Dial type:
Modify any of the above settings are not valid.
4 To modify the modem type, click Define Modem, highlight Intel as
manufacturer and the EtherExpress PRO/100 LAN+Modem PC
Card model.
Note
The default initialization string should suffice. To modify your
initialization string, click Define Modem and enter the new
initialization string in the Initialization section.
5 Click OK to save configuration and exit.
LapLink version 6.0
To set up the Intel modem or modify the present configuration:
1 In the Control Panel, click the Modem icon to access the Port Setup
window.
2 In the Port Setup Screen.
a Click the communications port that corresponds to the one
assigned to the modem.
b Select Modem under Type.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-12 PRO/100 LAN+Modem PC Card User’s Guide
c Enable Port by clicking box in that field.
3 Click Configure to configure the modem.
a Select your modem Speed under Modem Settings.
b Under Modem Type, select Hayes Generic.
c To modify the modem initialization string, which is usually not
necessary, click Customize and make any changes required. Click
OK, then Close.
d Enter the phone number(s) of your service provider and/or BBS
in the Connect over Modem window under Phone Number. Be
sure entries in Services and Security are correct for your envi-
ronment and/or the type of action you wish to exercise.
If too many programs are loaded via the LOAD or RUN statements in
your c:\windows\win.ini file, you will receive an “Out of System Memory
Error” when running LapLink. Correct this error by temporarily editing
out any special programs in those two statements. Make a backup copy of
the WIN.INI file before editing it. The load=c:\(Laplink
Directory)\llwload.exe line must reside in the WIN.INI, as it is required
for LapLink to work.
Operating inconsistencies will be experienced when Card and Socket
Services are used with LapLink. If you need to use LapLink, it is recom-
mended that Card and Socket Services not be used.
LapLink version 6.0 with Windows 95
To set up the Intel PRO/100 modem or modify the present configuration:
the steps are the same as those listed above for LapLink 6.0, except under
3.d.
1 In the Connect over Modem window under Dialing enter:
a The phone number(s) of your service provider and/or BBS
Phone Number.
b The location that you are dialing from under Dialing Location.
c Notice that in Connect Over Modem, Connect Using, the
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-13
EtherExpress PRO/100 LAN+Modem PC Card.
d Verify that the entry in Services section matches the action you
wish to exercise.
e There is no Security category.
Lotus cc:Mail Mobile version 2.22 with Windows 3.1
1 Copy the M16BLOT.MDM file to the default directory where the
Lotus cc:Mobile *.MDM files are located.
2 Setup Lotus cc:Mobile to use this M16BLOT.MDM file as follows:
a From the Lotus cc:Mail Mobile Main Menu, select Mobile.
b Next, select Location Setup.
c In Telephone, verify that your Dialing Rules and Strings are
correct.
d In Communications, highlight Default Communications Method,
then set.
• Connection Type = Modem.
• Modem Type = EtherExpress PRO/100 LAN+Modem PC Card
(select the correct modem).
• Serial Port = Communication Port assigned to the modem.
3 Click OK to save and close.
4 Enable SESSION.LOG to obtain the status of the modem:.
a From the Lotus cc:Mail Mobile Main Menu, select Mobile,
Mobile Setup:.
b Place a ‘check mark’ under Save cc:Mail Background Session
Log.
c Place a ‘check mark’ under Activate Diagnostics in cc:Mail
Background.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-14 PRO/100 LAN+Modem PC Card User’s Guide
Lotus cc:Mail Mobile version 2.22 with Windows 95
1 Copy the M16BLOT.MDM file to the default directory where the
Lotus cc:Mobile *.MDM files are stored.
2 Setup Lotus cc:Mobile to use this M16BLOT.MDM file as follows:
a From the Lotus cc:Mail Mobile Main Menu, select Mobile,.
b Next select Location Setup.
c In Telephone, verify that the Dialing Rules and Strings are
correct.
d In Communications, highlight Default Communications
Method,then Edit as follows:
• Connection Type = Modem.
• Modem Type = EtherExpress PRO/100 LAN+Modem PC
Card.
• Serial Port = Com Port setting used in Windows 95.
3 Click OK to save and close.
4 Enable SESSION.LOG to obtain the modem status of:
a From the Lotus cc:Mail Mobile Main Menu, select Mobile,
Mobile Setup:
b Place a ‘check mark’ under Save cc:Mail Background Session
Log.
c Place a ‘check mark’ under Activate Diagnostics in cc:Mail
Background.
Lotus Notes version 4.11A with Windows
To set up the Intel PRO/100 modem or modify the present configuration:
1 Copy the M16BLOT.MDM file to the default directory where the
Lotus Notes program is installed. \NOTES\DATA\MODEMS.
2 In the Lotus Notes Desktop screen, click File.
3 Click Tools.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-15
4 Click User Preferences.
5 Click the Ports icon.
6 Under Communications Ports.
a Select the appropriate protocol if connecting via the network.
b If connecting over the modem .
• Select the correct COM port.
• Click in the Port Enabled box.
7 If connecting over modem, click COM# Options,.
a Under Modem type, verify EtherExpress PRO/100
LAN+Modem PC Card is listed.
b Verify that the Maximum port speed is set to 115.2Kbps.
c Use the default initialization string. .
d Click OK to save changes and exit.
Lotus Notes version 4.11A with Windows 95 and NT
4.0
To set up the Intel modem or modify the present configuration:
1 Copy the M16BLOT.MDM file to the default directory where Lotus
Notes program is installed. \NOTES\DATA\MODEMS
2 In the Lotus Notes Desktop screen, click File.
3 Click Tools.
4 Click User Preferences....
5 Click the Ports icon.
6 Under Communications Ports.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-16 PRO/100 LAN+Modem PC Card User’s Guide
a Select the appropriate protocol if connecting via the network
b If connecting over the modem .
• Select the correct COM#.
• Click in the Port Enabled box.
7 If connecting over modem, click COM# Options,.
a Under Modem type, verify that EtherExpress PRO/100
LAN+Modem PC Card is listed.
b Verify that the Maximum port speed is set to 115.2 Kbps.
c Use the default initialization string. If you need to modify.the
string, do so under ControlPanel\Modems\Modem
Properties\Connection\Advanced\Extra Settings.
d
Click OK to save changes and exit.
Microsoft Dial-Up Adapter Network Setup for Windows
95
The Microsoft Dial-Up Adapter may be used for Remote Access Service
(RAS), remote connection to in-house server and/or to access the
Internet. To install the Dial-Up Adapter,
1 In the Control Panel, double-click the Network icon.
2 Click Add.
3 Double-click Adapter.
4 Highlight Microsoft under Manufacturers. Dial-Up Adapter will
appear under Network Adapters, click OK.
5 Windows 95 disks may be requested if not present in
C:\Windows\Options\Cabs sub-directory
6 Add the proper networking protocol for the Dial-Up Adapter (i.e.
TCP/IP, (IP, Subnet Mask, and Gateway may be required)).
7 Restart the computer when prompted.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-17
8 Modify the Dial-Up Adapter properties.
a Double-click the My Computer icon on the desktop.
b Double-click the Dial-Up Networking icon.
c Double-click the Make New Connection icon.
• Type in the Name of the computer or service you want to dial
• Under Select a Modem, select the Intel modem that is installed
• Click Configure, confirm COM Port and Maximum Speed
• Use the default Initialization String. To modify the string click
the Connection tab, and then Advanced Connection Settings.
Enter all changes under Extra Settings:
• Click OK to return to the Make New Connection screen, then
click Next
• Enter the Area Code and Telephone number of computer or
service, click Next, then Finish
Microsoft Remote Access Server (RAS)
1 Enable network functionality in Windows for Workgroups
a Double-click the Network Setup icon
b Click Networks
c Click Install Windows Network, then OK
d Click Drivers
e Click Add Adapter
f
By default Unlisted or Updated Network Adapter is highlighted,
if not, select it then click OK. When prompted, insert the latest
version of the Intel Network Driver disk in drive A:\, then click
OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-18 PRO/100 LAN+Modem PC Card User’s Guide
g Select M16BNDIS.EXE Real Mode (for all Intel adapters), then
click OK
h Remove the IPX/SPX Compatible Transport with NetBIOS
driver only, click Close, then OK
i
In the Windows Setup screen click Yes to All, “...to replace all
later files with the version you are installing now...” Windows
disks #7 and 8 are required to complete the installation
j
Confirm that the Local Network is functional and that you can
access the modem using the TERMINAL program in Accesso-
ries Group before proceeding to the next step.
2 Copy the M16BRAS1.INF file from the \scripts directory on disk 2
to the c:\windows\system directory.
3 Exit Windows and go to the C:\Windows\System sub-directory.
Back up the original MODEM.INF with the following command:
COPY MODEM.INF MODEM.BAK
4 Append the Intel M16BRAS1.INF file to the end of the
MODEM.INF file. To do this, issue the following commands:
COPY MODEM.INF+M16BRAS1.INF MODEM.NEW
COPY MODEM.NEW MODEM.INF
5 Modify the new MODEM.INF in the [Intel EtherExpress PRO/
100 Lan+Modem PC Card] section, edit the following lines:
MAXCARRIERBPS= 56000
MAXCONNECTBPS= 56000
6 Save the file and exit the editor
7 Double-click the Windows Network Setup icon
8 Install Remote Access Service in Windows for Workgroups
a Double-click the Network Setup icon, then the RASSTART icon
b Click Install to continue
c In the Remote Access screen click Yes to All, “...to replace all
later files with the version you are installing now, press Yes to
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Applications 5-19
All.” Windows disks #7 and 8 are required to complete the
installation
d In the Remote Access Configuration screen,
• Click the COM port assigned to the Intel modem
• Under Device, select Intel EtherExpress PRO/100.
• Click OK to save changes, then Click Restart Computer
9 Restart RAST to input the phone number(s) into RAS
a Click Edit to access the Edit Phone Book Entry screen.
b Input all other required data
c Under Port: select Any modem port,
d Click OK to save and exit
Prodigy Internet version 1.1.6 with Windows 95
To set up the Intel modem or modify the present configuration:
1
Double-click NetAssist for Prodigy Internet.
Click Dialer Settings.
2
3
Click Modem Info. Highlight the EtherExpress PRO/100
LAN+Modem.
4
By default, there should be an ‘X’ in the ‘Check this if you have a
PCMCIA modem’.
5
6
7
8
Click Change Modem Strings.
Modify the Init String: line to read AT&FE0Q0V0, then click OK.
Click OK to exit the Modem Settings menu.
Click Exit to accept changes and close the NetAssist Windows
Application - NetAssist.
9
Double-click the Prodigy Internet icon to access the service.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-20 PRO/100 LAN+Modem PC Card User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6
Modem Reference
This chapter contains a comprehensive modem reference guide, including
result codes and all AT commands and S-Registers supported by the
PRO/100 LAN+Modem PC Card.
Result Codes
Long
Short
Description
OK
0
1
2
3
4
5
6
7
8
Command successfully executed
Connect
CONNECT
RING
Incoming ring signal detected
Carrier detect failed/carrier dropped
Command is invalid
NO CARRIER
ERROR
CONNECT 1200
NO DIALTONE
BUSY
Connection established at 1200bps
No tone during interval set with S6
Busy signal detected
NO ANSWER
CONNECT 2400
CONNECT 4800
CONNECT 9600
CONNECT 14400
CONNECT 19200
CONNECT 57600
Remote end never answered
10 Connection established at 2400bps
11 Connection established at 4800bps
12 Connection established at 9600bps
13 Connection established at 14400bps
14 Connection established at 19200bps
18 Connection established at 57600bps
CONNECT 1200/75 22 Connection at 1200 (Tx)/75 (Rx) bps
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2 PRO/100 LAN+Modem PC Card User’s Guide
Long Short Description
CONNECT 75/1200 23 Connection at 75 (Tx)/1200 (Rx) bps
CONNECT 7200
CONNECT 12000
CONNECT 38400
CONNECT 300
24 Connection established at 7200bps
25 Connection established at 12000bps
28 Connection established at 38400bps
40 Connection established at 300bps
55 Connection established at 21600bps
56 Connection established at 24000bps
57 Connection established at 26400bps
58 Connection established at 28800bps
59 Connection established at 31200bps
60 Connection established at 33600bps
70 Connection established at 32000bps
71 Connection established at 34000bps
72 Connection established at 36000bps
73 Connection established at 38000bps
74 Connection established at 40000bps
75 Connection established at 42000bps
76 Connection established at 44000bps
77 Connection established at 46000bps
78 Connection established at 48000bps
79 Connection established at 50000bps
80 Connection established at 52000bps
81 Connection established at 54000bps
82 Connection established at 56000bps
86 Connection established at 16800bps
87 Connection at 115200bps
CONNECT 21600
CONNECT 24000
CONNECT 26400
CONNECT 28800
CONNECT 31200
CONNECT 33600
CONNECT 32000
CONNECT 34000
CONNECT 36000
CONNECT 38000
CONNECT 40000
CONNECT 42000
CONNECT 44000
CONNECT 46000
CONNECT 48000
CONNECT 50000
CONNECT 52000
CONNECT 54000
CONNECT 56000
CONNECT 16800
CONNECT 115200
DELAYED
88 Delay in effect for dialed number
89 Dialed number is blacklisted
BLACKLISTED
BLACKLIST FULL
+FCERROR
90 Blacklist is full
+F4Fax command error
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-3
Long
Short Description
CARRIER 75/1200
CARRIER 1200
CARRIER 1200/75
CARRIER 2400
CARRIER 4800
CARRIER 7200
CARRIER 9600
CARRIER 12000
CARRIER 14400
CARRIER 16800
CARRIER 19200
CARRIER 21600
CARRIER 24000
CARRIER 26400
CARRIER 28800
CARRIER 31200
CARRIER 33600
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Carrier detected 75 (Tx)/1200 (Rx) bps
Carrier detected at 1200bps
Carrier detected 1200 (Tx)/75 (Rx) bps
Carrier detected at 2400bps
Carrier detected at 4800bps
Carrier detected at 7200bps
Carrier detected at 9600bps
Carrier detected at 12000bps
Carrier detected at 14400bps
Carrier detected at 16800bps
Carrier detected at 19200bps
Carrier detected at 21600bps
Carrier detected at 24000bps
Carrier detected at 26400bps
Carrier detected at 28800bps
Carrier detected at 31200bps
Carrier detected at 33600bps
COMPRESSION: MNP5
COMPRESSON: V.42BIS
COMPRESSION: NONE
*
*
*
MNP/5 compression enabled
V.42bis compression enabled
Data compression disabled
PROTOCOL: NONE
PROTOCOL: LAP-M
PROTOCOL: MNP
*
*
*
Standard asynchronous mode
V.42 error control mode: LAP-M
Alternate EC protocol: MNP
_____________________
*These result codes do not have numeric (short) equivalents.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4 PRO/100 LAN+Modem PC Card User’s Guide
AT Command Reference
With the exception of the “Special Commands” described at the beginning
of the Command Reference, all commands must be preceded by the AT
attention code (or command prefix) and terminated by pressing the Enter
key.
The modem responds with the result code OK, which means it under-
stands and can execute the command, or with ERROR, which means that
the modem does not understand the command or that the command is
invalid. For a complete list of result codes, see the beginning of this
chapter.
The modem must be in command mode when any command other than
the online escape sequence is entered. Commands entered when the
modem is in online mode are treated as data and transmitted as such to
the modem at the other end of the line.
Special Commands
+++ Online Escape Sequence
The escape sequence is used to switch to command mode from online
mode during a session with a remote modem. Type three “plus signs.” The
escape sequence is not preceded by the AT command prefix, nor does it
require the Enter key. The setting of S-Register S2 determines the ASCII
character used. S2=43 is the default (the “+” sign). 0-127 are valid. To
disable the command, set S2 to a value greater than 127. Use the ATO
(“AT” and letter “oh”) command to return to online mode.
Insert a pause before and after the escape sequence to prevent misinter-
pretation of the escape sequence as data. Use S-Register S12 to set the
length of the pause.
A/
Repeat Last Command
The A/ command causes the modem to repeat the last command string.
The command executes as soon as / is typed. It does not require the AT
command line prefix, nor does it need to be followed by Enter.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-5
AT Command Reference
Answer
A
Typing ATA causes the modem to go off-hook and respond to an
incoming call by generating a carrier signal and starting the handshaking
process. This must be the only command or the final command in the
command line.
If the handshaking process is successful and a connection is established,
the normal CONNECT message is displayed. If the carrier signal is not
detected within the time specified in S-Register S7, a NO CARRIER result
code is displayed.
Bn Select Communications Standard
The ATBn command selects the communication standard (ITU or Bell)
to be used by the modem, as follows:
B0
Use ITU V.22 at 1200bps. B0 selects ITU V.22 at
1200bps and ITU V.21 at 300bps.
B1
Use Bell 212A at 1200bps. B1 selects Bell 212A at
1200bps and Bell 103J at 300bps.
B2
Unselect V.23 reverse channel.
Select V.23 reverse channel.
B3
B15
Selects V.21 when the modem is at 300bps (same as
B0).
B16
Selects Bell103J when the modem is at 300bps (same as
B1).
Note
The ATB1 and ATB16 parameter settings are not available in
some countries. Defaults are country-specific.
Break (Escape) command
See “Special Commands” at the beginning of this Command Reference
section.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-6 PRO/100 LAN+Modem PC Card User’s Guide
Cn Carrier Control
The ATCn command, where n is 1, guarantees backward compatibility
with communications software that issues the C1 command. C0 is not
supported; it may set some modems to "receive only mode."
C0
Transmit carrier always off (not supported).
C1
Normal transmit carrier switching.
Dn Dial A Telephone Number
The ATDn command is used to dial a telephone number. The n repre-
sents a dial string consisting of dial digits/characters and dial modifiers
(see below) and must not exceed 40 characters. Spaces, hyphens, and
parentheses can be used for clarity, but they are ignored by the modem.
The Dial command can be used for either pulse (rotary) or tone dialing.
The dial digits/characters are 0 - 9 A B C D # *. The characters A B C D
and the symbols # and * represent specific tone pairs and can be used
only when tone dialing. These characters and symbols are ignored when
pulse dialing is used. Some countries restrict or prohibit the use of some
of these characters.
Dial Modifiers
Dial modifiers are recognized by the modem only when they are part of a
dial string following the ATD command. Possible dial modifiers are:
L
Redial Last Number
Redials last number if used as first character following ATD. Other-
wise it is ignored.
P
Pulse Dialing Method
The P modifier is used with the Dial command to instruct the
modem to pulse dial the telephone number that follows.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-7
Dial Modifiers (continued)
S=n Dial a Stored Telephone Number
The S modifier instructs the modem to dial a number that had been
previously stored by the use of the AT&Zn=x command. The
command to dial a stored telephone number is ATDS=n, where n
represents telephone number storage location 0 or 1. For example,
ATD P S=1 pulse dials the telephone number written to telephone
number storage location 1.
,
Delay Processing the Next Character
When the comma (,) modifier is included as part of the dial string
following the ATD command, the modem pauses before processing
the next character in the dial string. The duration of the pause is
dictated by the contents of S-Register S8.
The , modifier is frequently inserted after the digit (usually 9) used to
obtain an outside line from a PBX to allow sufficient time for the dial
tone to occur before the modem dials the telephone number. The W
modifier can be used in place of the comma.
Some countries place restrictions on the amount of time a modem
may delay during dialing.
T
Tone Dialing Method
The T modifier is used with the Dial command to instruct the
modem to tone dial the telephone number that follows. See also the
ATT command.
W
Wait for Second Dial Tone
The W modifier instructs the modem to wait for a dial tone before
processing the remaining characters in the dial string.
!
Hook Flash
The ! modifier serves as a switch hook (or hook flash) signal. This
causes the modem to hang up (go on-hook) for about 0.5 seconds
then return to off-hook (the actual duration of the hook flash varies
in different countries).
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8 PRO/100 LAN+Modem PC Card User’s Guide
Dial Modifiers (continued)
@
Wait for Quiet Answer
The @ modifier in a dial string instructs the modem to wait for five
seconds of silence after dialing the number. If silence is not detected,
the modem sends a NO ANSWER result code to the user.
;
Return to Command Mode after Dialing
The semicolon (;) dial modifier can be used only at the end of a
command line, immediately preceding the Enter, and instructs the
modem to return to the command mode immediately after dialing and
without breaking the connection with the distant modem.
^
Disable Data Calling Tone Transmission
The ^ modifier in a dial string disables data calling tone for the
current call (calling tone is automatically enabled in many countries).
This modifier is not available in all countries.
$
Credit Card Tone Detect
The $ modifier in a dial string instructs the modem to wait for a
credit card “bong” tone before processing the remaining characters in
the dial string.
En Echo Command
The ATEn command, where n represents 0 or 1, determines if the
commands you issue through the keyboard to the modem in command
mode are displayed (echoed) on your computer’s monitor screen.
E0
Disable echo to the computer
E1
Enable echo to the computer (default)
If the commands you type are not displayed on your monitor screen, your
software is set to expect character echo from the remote system. You can
remedy this by typing in the command ATE1. If the commands you type
are displayed on your monitor with the characters duplicated,
LLIIKKEETTHHIISS, type in the ATE0 command.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-9
Fn Online Data Character Echo command
Ths ATFn command determines whether the modem will echo data from
the DTE. This modem does not support the F0 version of the command.
To ensure backward compatibility, the modem will accept F1.
F0
Online data character echo enabled (not supported;
returns ERROR)
F1
Online data character echo disabled
Hn Switch Hook Options
The ATHn command hangs up the modem or prepares it for dialing.
ATH0
Causes the modem to go on-hook (default).
ATH1
Causes the modem to go off-hook (this command is
restricted in some countries).
In
Request ID Information
The ATI command has various options which are used to instruct the
modem to provide specific information about itself.
I0
I1
I2
Displays modem controller firmware revision (same as
I3)
Calculates ROM checksum and displays it on the DTE
(for example, 12AB)
Performs a ROM check and calculates and verifies the
checksum. displaying OK or ERROR.
I3
Displays modem firmware revision information
Returns country code (for example, North America)
I12
Download from Www.Somanuals.com. All Manuals Search And Download.
6-10 PRO/100 LAN+Modem PC Card User’s Guide
Ln Monitor Speaker Volume
The ATLn command, where n represents 0, 1, 2, or 3, is listed here for
backward compatibility reference only. The volume of the monitor
speaker is controlled by the laptop computer, not by the modem.
Mn Speaker On/Off Selection
The ATMn command, where n represents 0, 1, 2, or 3, enables or disables
the transmission of sound signals from the modem to the computer
speaker. (Sound production also requires that the computer speaker be
enabled.)
M0
M1
M2
M3
Speaker always off.
Speaker on until data carrier is detected
Speaker always on when modem is off-hook
Speaker off as digits are dialed, then on after dialing
until data carrier is detected
Nn Negotiation of Handshaking Options
The ATNn command, where n represents 0 or 1, determines whether or
not the sending modem performs a negotiated handshake when the speed
of the answering modem is different from that of the sending modem.
N0
When originating or answering, handshake only at the
communication standard specified by the contents of S-
Register S37 and the ATBn command option selected.
N1
When originating or answering, handshake only at the
communication standard specified by the contents of S-
Register S37 and the ATBn command option selected.
During handshaking, fall back to a lower speed, if
required. (default)
On Online Command
If the modem has been switched to command mode, typing in the ATO0
command will return it to the online mode with the existing connection.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-11
O0
Instructs modem to leave online command mode and
return to data mode (see +++ Escape Sequence under
“Special Commands”)
O1
O2
This setting issues a retrain command before returning
to online data mode.
This setting issues a rate negotiation command before
returning to online data mode.
P
Select Pulse Dialing
The ATP command instructs the modem to use pulse (rotary) dialing.
This mode will remain in force for all dialing procedures unless an ATT
command is issued or the dial string contains a T dial modifier.
Qn Result Code Display Options
The setting of the ATQn command, where n represents 0 or 1, deter-
mines whether or not result codes (such as OK, CONNECT, RING, NO
CARRIER, and ERROR) are displayed on your PC’s screen.
Q0
Display of result codes enabled.
Display of result codes disabled.
Q1
Repeat command
See “Special Commands” at the beginning of this chapter.
T
Select Tone Dialing
The ATT command instructs the modem to use tone dialing. This mode
will remain in force for all dialing procedures unless an ATP command is
issued or the dial string contains a P dial modifier. Tone dialing is the
factory-default setting.
Vn Result Code Format Options
The ATVn command, where n represents 0 or 1, determines if result
codes are displayed as numeric (short form) codes or words (long form).
Numeric result codes contain only one or two digits and this form could
be used, for example, when the modem is controlled by a software
terminal emulation program that uses script files. See the list at the
Download from Www.Somanuals.com. All Manuals Search And Download.
6-12 PRO/100 LAN+Modem PC Card User’s Guide
beginning of this chapter showing result codes in both long and short
formats..
Type the command ATV or ATV0 to select numeric result codes. The
factory default is to display the result codes as words (ATV1). You should
issue an ATV1 command either to reset the factory default after a change
has been made or to select the long-form (word) result codes. Negotiation
progress messages (extended result codes) are those with a numerical value
of 40 or more.
Four other AT commands, two dial modifiers, and an S-Register are also
directly involved in the generation and display of result codes. These are
the ATQn, ATVn, ATWn, and ATXn commands, the ATDW and
ATD@ dial modifiers, and S-Register S95.
Wn Negotiation Progress Message Selection
The ATWn command, where n represents 0, 1, or 2, works in conjunction
with S-Register S95 to determine how that subset of the result codes —
called negotiation progress messages or extended result codes — will be
used to report the type of connection, protocol, and other communication
techniques that resulted from handshaking and subsequent negotiation.
The options available to represent n in the ATWn command are:
W0
W1
W2
CONNECT result code reports DTE speed. If S-
Register S95=0, disable the display of all extended
result codes.
CONNECT result code reports DTE speed. If S-
Register S95=0, enable the display of CARRIER and
PROTOCOL extended result codes only.
CONNECT result code reports DCE (modem-to-
modem) speed. If S-Register S95=0, disable the display
of all extended result codes.
Xn Result Code Set/Call Progress Option
The ATXn command, where n represents 0-4, controls how the modem
responds to dial tone and busy signals and how it displays CONNECT
result codes. The options available to specify with the ATXn command
are:
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-13
X0
X1
X2
X3
X4
Result codes 0-4 enabled. Busy detect and dial tone
detect disabled.
Result codes 0-5, and 10 enabled. Busy detect and dial
tone detect disabled.
Result codes 0-6, and 10 enabled. Busy detect disabled
and dial tone detect enabled.
Result codes 0-5, 7, and 10 enabled. Busy detect
enabled and dial tone detect disabled.
Result codes 0-7, and 10 enabled. Busy detect and dial
tone detect enabled.
Note
Some countries do not allow busy detect or dial tone detect to be
disabled.
Yn Long Space Disconnect Option
The ATYn command, where n represents 0 or 1, determines whether or
not the modem will disconnect a call when it receives a long space (1.6
seconds Break) signal during a V.22bis connection.
Y0
Disables the long space disconnect facility (supported
for backward compatibility reference only).
Y1
Enables the long space disconnect facility (not supported).
Zn Recall Stored Profile
The ATZn command, where n represents 0, disconnects any call that is
currently in progress and reloads the user configuration profile stored in
nonvolatile memory as the active configuration profile.
Z0
Disconnect and reload the profile contained in storage
location 0 as the active configuration profile.
&Bn V.32 Automatic Retrain Options
The EtherExpress PRO/100 LAN/Modem PC Card always retrains. The
automatic retrain feature cannot be disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-14 PRO/100 LAN+Modem PC Card User’s Guide
&B0
Disables the V.32 automatic retrain capability (not
supported).
&B1
Enables the V.32 automatic retrain capability (sup-
ported for backward compatibility only).
&Cn Data Carrier Detect (DCD)
The AT&Cn command, where n represents 0 or 1, selects the method by
which the modem handles the carrier detect signal.
&C0
The carrier detect signal is forced on regardless of the
condition of the distant modem’s carrier.
&C1
The state of the carrier from the remote modem is
monitored. The local modem’s DCD signal is on when
the remote modem’s carrier signal is detected, and off
when it is not (default).
&Dn Data Terminal Ready (DTR) Options
The AT&Dn command, where n represents 0-3, controls how the Data
Terminal Ready (DTR) signal is used by the modem.
&D0
Ignore the DTR signal from the computer and treat it
as always on.
&D1
Monitor DTR and, when an ON-to-OFF transition of
the DTR signal occurs, switch to command mode, issue
an OK result code, and remain connected.
&D2
Monitor DTR and, when an ON-to-OFF transition of
the DTR signal occurs, hang up the line and switch to
command mode.
&D3
Monitor DTR and, when an ON-to-OFF transition of
the DTR signal occurs, hang up, reset the modem and
switch to the initialization state.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-15
&Fn Load Factory Settings
The AT&F command loads factory default parameters from ROM into
the active configuration profile, replacing the parameters stored there.
This command must be issued by itself. If it is used with another AT
command, its function will be ignored.
&F0
&F5
Recall factory settings as active configuration
Recall factory settings appropriate for ETC mode as
active configuration. This command enables ETC
operation. It is automatically set upon detection of a
cellular phone. The following options are set with &F5:
Local Factory Settings
Function
MTC Implementation
LAPM-only error correction
\N4
Transmit level fixed per cellular phone S92
Wait for carrier = 90 sec
CD loss delay = 10 sec
Auto FF/FB enabled
Start up at 9600bps
S7=90
S10=100
N/A
S40=2
&Gn V.22bis Guard Tone Selection
This option is for international use only. It is not used in North America.
The AT&Gn determines which guard tone, if any, to transmit while in
answer mode (transmitting in the high band). The value of n can be 0, 1,
or 2. This parameter is set automatically for most countries that require it.
&G0
&G1
&G2
No guard tone set
550-Hz guard tone set
1800-Hz guard tone set
&Jn Auxiliary Relay Option
&J0
&J1
Auxiliary relay is never closed
Not supported (returns ERROR)
Download from Www.Somanuals.com. All Manuals Search And Download.
6-16 PRO/100 LAN+Modem PC Card User’s Guide
&Kn Local Flow Control Options
The AT&Kn command, where n represents 0-4, determines how the flow
control between the computer and the local modem is handled.
&K0
&K1
&K2
&K3
&K4
Disable local flow control.
Reserved.
Reserved.
Enable RTS/CTS flow control (default).
Enable XON/XOFF flow control.
&Mn Asynchronous Communications Mode
The AT&Mn command, where n represents 0-4, determines how the
flow control between the computer and the local modem is handled.
&M0
Asynchronous mode (default; supplied for backward
compatibility only).
&M1
&M2
&M3
&M4
Reserved.
Reserved.
Reserved.
Reserved.
&Pn Pulse Dial Make-to-Break Ratio Selec-
tion (Japan only)
The AT&Pn command, where n represents 0 or 1, controls the ratio of
the off-hook (make) to on-hook (break) interval used by the modem when
it pulse dials.
&P0
&P1
&P2
Selects 39:61 make/break ratio at 10 pps (default)
Selects 33:67 make/break ratio at 10 pps
Selects 33:67 make/break ratio at 20 pps
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-17
&Qn Asynchronous Communications Mode
&Q0
&Q1
&Q2
&Q3
&Q4
&Q5
&Q6
&Q7
Asynchronous mode, buffered (same as \N0)
Reserved
Reserved
Reserved
Reserved
Error control mode, buffered (default; same as \N3)
Asynchronous mode, buffered (same as \N0)
Reserved
&Sn Data Set Ready (DSR) Options
The AT&Sn command controls the functions of the modem’s DSR
circuits.
&S0
The DSR signal remains on all the time the modem is
powered on (default)
&S1
The DSR signal is on during handshaking and is off
when carrier is lost.
&Tn Self-Test Commands
The AT&Tn command allows the user to perform diagnostic tests on the
modem.
&T0
Abort. Stops any test in progress.
&T1
Local analog loop. this test verifies modem operation,
as well as the connection between the modem and
computer. The modem must be off-line when this test
is run.
&T3
&T6
Local digital loopback test.
Remote digital loopback test. This test can verify the
integrity of the local modem, the communications link,
and the remote modem. The modems must be online
with error control disabled when this test is run.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-18 PRO/100 LAN+Modem PC Card User’s Guide
&V View Configuration Profile
The AT&V command displays the contents of the active configuration
profile.
&Wn Write Active Profile to Memory
The AT&Wn command, where n is 0, allows you to save a copy of the
current active configuration profile to nonvolatile memory. This profile
can be restored at any time by using the ATZ command or a power-up
reset of the modem.
&Yn Select Stored Profile for Hard Reset
This command is included for compatibility with applications that use the
&Y0 command. It does not affect the behavior of the modem.
&Y0
Select stored profile 0 on power up
ERROR
&Y1
&Zn=x
Store Telephone Number
The AT&Zn=x command is used to store a telephone number for later
dialing using the ATDS=n (dial stored number) command. In this
command, n is 0 or 1 representing 2 storage locations and x is the stored
number.
The dial string may contain up to 40 characters.
\Gn Modem Port Flow Control
The AT\Gn command determines whether XON/XOFF flow control
will be used.
\G0
Returns OK for compatibility (default)
Not supported; returns ERROR
\G1
\Jn Adjust BPS Rate Control
\J0
Turn off feature (default)
Turn on feature
\J1
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-19
\Kn Break Control
The AT\Kn command determines how the modem processes a Break
signal received from the local DTE during a connection (online).
\K5
Modem sends Break to remote modem in sequence
with transmitted data, non-destructive/non-expedited
(default)
\Nn Error Mode Control Selection
The AT\Nn command sets the type of error correction supported by the
modem when sending or receiving data.
\N0
\N1
\N2
Buffered mode. No error control (same as &Q6).
Buffered mode (same as \N0)
LAPM, MNP or disconnect mode. This is also known
as reliable mode.
\N3
LAPM, MNP, or buffered (default). The modem
attempts to connect in LAPM error control mode. If
this fails, the modem attempts to connect in MNP
mode. If this fails, the modem connects in buffered
mode and continues operation. This is also known as
V.42 auto-reliable mode (same as &Q5)
\N4
\N5
LAPM or disconnect. The modem attempts to connect
in LAPM error control mode. If this fails, the call will
be disconnected.
MNP or disconnect mode. The modem attempts to
connect using MNP 2-4 error control procedures. If
this fails, the modem disconnects. This is also known as
MNP reliable mode.
\Qn Local Flow Control Selection
The AT\Qn command sets the type of flow control used on the serial
port to adjust for differences in modem port speed.
\Q0
\Q1
\Q3
Disables flow control (same as &K0)
Sets flow control to XON/XOFF (same as &K4)
RTS/CTS to DTE (default; same as &K3)
Download from Www.Somanuals.com. All Manuals Search And Download.
6-20 PRO/100 LAN+Modem PC Card User’s Guide
\Tn Inactivity Timer Limit
The AT\Tn command specifies length of time (in minutes) that the
modem waits before disconnecting when no data is sent or received. The
time period can be set at n = 0 - 255. A setting of zero disables the timer.
As an alternative, the timer may be specified in S-Register S30. This
function is only applicable in buffer mode.
\Xn XON/XOFF Pass Through
\X0
Modem process XON/XOFF flow control characters
locally (default)
\X1
Not supported; returns ERROR
%B View Numbers in Blacklist
If blacklisting is in effect, the AT%B command displays the numbers for
which the last call attempted in the past two hours failed. In countries that
do not require blacklisting, this command returns ERROR.
%Cn Data Compression Control
The AT%Cn command determines the operation of V.42bis and MNP
class 5 data compression. Online changes do not take effect until a
disconnect occurs.
%C0
V.42bis/MNP Class 5 compression disabled (no data
compression)
%C1
%C2
%C3
MNP Class 5 compression enabled (no V.42bis)
V.42bis compression enabled (no MNP Class 5)
V.42bis/MNP Class 5 data compression enabled
(default)
-Cn Data Calling Tone
Data calling tone is a tone of a certain frequency and cadence specified in
V.25 that allows remotes data/fax/voice discrimination. The frequency is
1300 Hz with a cadence of 0.5 seconds on and 2 seconds off.
-C0
Disables calling tone (default)
Enables calling tone
-C1
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-21
Note
Some countries do not permit calling tone to be disabled.
+GCAPRequest Complete Capabilities List
Syntax:
AT+GCAP
AT+GCAP=?
This command displays one or more lines of information text, in a
standard format, describing the basic capabilities of the modem. This
allows a software package to determine which groups of extended-syntax
commands the modem supports. The response may contain one or more
of the following responses:
+CGSM GSM (+C) commands.
+DS
+ES
Data Compression (+D) commands.
Eror Control (+E) commands.
+FCLASS Fax (+F) commands.
+MS
+W
Modulation Control (+M) commands.
Wireless (+W) commands
+GCAP=? may be used to determine whether the modem supports the
+GCAP command: an OK response indicates support, ERROR indicates
non-implementation.
+GCI Country of Installation
Syntax:
AT+GCI=<T.35 code>
AT+GCI?
AT+GCI=?
This command configures the modem for the country of use, selecting
operational parameters and ensuring conformity to the requirements of
the selected country’s telephone network. The +GCI parameter may only
be changed when the modem is in an idle state.
<T.35 code> refers to the 8-bit hexadecimal number next to the country
in the list below.
To determine which countries are currently supported, use AT+CGI=?
The command will respond with the T.35 codes for the countries sup-
Download from Www.Somanuals.com. All Manuals Search And Download.
6-22 PRO/100 LAN+Modem PC Card User’s Guide
ported. To determine the current country setting, use AT+GCI? The
command will respond with the T.35 code for the country selected.
To change the current country selection, use AT+GCI=<T.35 code>
Country
Australia
Austria
<T.35 code>
09
0A
0F
20
Belgium
Canada
China
26
Denmark
Finland
31
3C
3D
04
France
Germany
Hong Kong
Indonesia
Ireland
50
54
57
Italy
59
Japan
00
Korea
61
Malaysia
Netherlands
New Zealand
Norway
6C
7B
7E
82
Portugal
Singapore
Spain
8B
9C
A0
A5
A6
FE
A9
B4
B5
Sweden
Switzerland
Taiwan
Thailand
United Kingdom
United States
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-23
+GMIRequest Manufacturer Identification
Syntax:
AT+GMI
AT+GMI=?
This command displays one or more lines of information text, identifying
the manufacturer of the modem. +GMI=? may be used to determine
whether the adapter supports the +GMI command: an OK response
indicates support, ERROR indicates non-implementation.
+GMM
Request Model Identification
Syntax:
AT+GMM
AT+GMM=?
This command displays one or more lines of information text, identifiying
the modem model. +GMM=? may be used to determine whether the
modem supports the +GMM command: an OK response indicates
support, ERROR indicates non-implementation.
+GMR
Request Revision Identification
Syntax:
AT+GMR
AT+GMR=?
This command displays one or more lines of information text, identifiying
the revision level of the firmware of the modem. +GMR=? may be used
to determine whether the adapter supports the +GMR command: an OK
response indicates support, ERROR indicates non-implementation.
+MS Modulation Selection
The AT+MS parameter controls data modulations and bit rates that may
be negotiated between a local and remote modem. It accepts four
subparameters.
Syntax:
AT+MS=<carrier>,<automode>,<min_rate>,<max_rate>
AT+MS?
AT+MS=?
+MS?
Reports the current settings of subparameters
Download from Www.Somanuals.com. All Manuals Search And Download.
6-24 PRO/100 LAN+Modem PC Card User’s Guide
+MS=?
Displays range of acceptable values for each
subparameter
<carrier>
Specifies the preferred modulation to be used in
originating or answering a connection. The
<carrier> subparameter is an unquoted string
of characters. If the <carrier> parameter is
specified, the other subparameters will revert to
factory defaults. If <carrier> is omitted, any
unspecified parameters will keep their current
values (for example, AT+MS=,0 or
AT+MS=,,,2400).
Values accepted for <carrier> are the following:
B103
B212
V21
Bell 103 (300bps)
Bell 212A (1200bps)
ITU-T V.21 (300bps)
ITU-T V.22 (1200bps)
ITU-T V.22bis (2400bps)
V22
V22B
V23C
ITU-T V.23 with constant carrier (1200/75 or 75/
1200bps)
V32
ITU-T V.32 (4800 or 9600bps)
V32B
ITU-T V.32bis (4800 - 19200bps)
V34
ITU-T V.34 (2400 - 33600bps)
K56
(default) Lucent/Rockwell K56flex (32000 - 56000bps)
<automode>
Enables or disables negotiation of an alternative
<carrier> if the preferred modulation is not
available.
Values accepted for <automode> are the following:
0
Disabled. Modem will disconnect if it is unable to
negotiate a connection with the specified <carrier>.
1
Enabled (default). If the specified <carrier> is unavail-
able, modem will attempt to negotiate an alternative
carrier as appropriate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-25
Specifies the lowest bit rate at which the
modem may establish a connection. (This value
is fixed at zero for the EtherExpress™ PRO/
100 LAN/Modem PC Card Adapter.)
<min_rate>
<max_rate>
Specifies the highest bit rate at which the
modem may establish a connection. For
modulations that support only a fixed bit rate
(such as V.22bis), <max_rate> has a fixed value
to which it defaults. If the default rate or a rate
other than zero is specified, the modem will
return ERROR. This subparameter accepts the
following values: 0, 300, 1200, 2400, 4800, 7200,
9600, 12000, 14400, 16800, 19200, 21600,
24000, 31200, 33600bps. If unspecified (set to
0), <max_rate> is determined by the value of
<carrier>.
If the <carrier> setting is K56, the <max_rate>
subparameter should be left at the default value
(zero).
S-Register Reference
This section provides information on all the S-Registers supported by the
Intel EtherExpress™ PRO/100 LAN/Modem PC Card Adapter. It is
divided into two parts:
• Introduction to S-Registers
• S-Register Reference (in numerical order)
Introduction to S-Registers
The Intel EtherExpress™ PRO/100 LAN/Modem PC Card Adapter uses
memory storage locations, or S-Registers, to hold information controlling
its operating environment. Few of these S-Registers require attention from
modem users.
Some of the S-Registers are reserved. These either contain parameter bit
maps for the internal use of the modem or are not in current use. Gener-
ally, modem users should not alter or write to any of these reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
6-26 PRO/100 LAN+Modem PC Card User’s Guide
S-Registers because doing so could result in the modem behaving unpre-
dictably.
To display the value of an S-Register, type ATSn? where n is the number
of the S-Register, then press Enter.
To modify the value of an S-Register, type ATSn=r where n is the S-
Register number and r is the new value or setting, then press Enter.
S-Register Reference
S0 Ring to Answer After
The contents of register S0 sets the number of rings required before
the modem goes off-hook to answer an incoming call (auto answer).
The value can range from 0 to 255. ATS0=0 disables the auto-
answer function. The default is 0.
S1 Ring Counter
This register is read only. The value of S1 increments with each ring.
If no rings occur over a six-second interval, the register is cleared.
The value of S1 can range from 0 to 255. The default is 0. Limits are
country specific.
S2 AT Escape Character
Register S2 defines the ASCII character used in the Escape se-
quence. This command is used to return to command mode without
losing the connection with a remote modem. Default is S2=43,
which is the “+” character. Thus the default Escape sequence is
+++. ASCII values 127 and below can be used. To disable this
Escape sequence, set S2 equal to a value greater than 127.
S3 Command Line Termination Character
This register contains the ASCII value of the command line
terminating character (carriage return). The factory default value is
ASCII 13 — the carriage return character. You can set register S3
to any value between 0 and 127.
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-27
S4 Response Formatting Character
This register contains the ASCII value of the line feed character.
The factory default value is 10. You can set register S4 to any value
between 0 and 127. The modem uses a line feed character in
command mode when it responds to the computer.
S5 Command Line Editing Character
This register contains the ASCII value of the backspace character
and is applicable to asynchronous transmissions only. The factory
default value is 8. You can set register S5 to any value between 0
and 32, or to 127. The modem will not recognize the backspace
character if it is set to a value greater than ASCII 32.
S6 Wait Before Blind Dialing
This register determines how long the modem waits after going off-
hook before dialing the first digit. The wait must be at least 2
seconds. Register S6 can be set to any value between 2 and 65
seconds. The default is 2 seconds. The value of the W dial modifier
will override the value in register S6. This operation, however, may
be affected by some ATX options according to country restrictions.
Defaults and limits are country-specific.
S7 Connection Completion Time-Out
This register determines the number of seconds the originating
modem waits for a carrier signal from the answering modem before
hanging up. The timer is started when the modem finishes dialing
(originate), or goes off-hook (answer). In originate mode, the timer
is reset upon detection of an answer tone if allowed by country
restriction. The timer also specifies the wait for silence time with the
@ dial modifier (in seconds). S7 is not associated with the W dial
modifier. Register S7 can be set at from 1 to 255 seconds with a
default of 50 seconds. Defaults and limits are country-specific.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-28 PRO/100 LAN+Modem PC Card User’s Guide
S8 Duration of Pause for Comma Dial Modi-
fier
This register determines the number of seconds to pause for each
comma (,) in a dial string or command line. The default is 2
seconds, but any value from zero to 65 is acceptable. Defaults and
limits are country-specific.
S10 Delay Between Lost Carrier/Hang Up
This register specifies the time (in tenths of a second) that the
modem waits after carrier loss before hanging up. The default is 20
(2.0 seconds). This allows for temporary carrier loss without causing
the local modem to disconnect. Register S10 will accept a value
ranging from 1 to 254 in tenths of a second (0.1 to 25.4 seconds).
Defaults and limits are country-specific.
S11 DTMF Tone Duration
This register determines the “touch tone” dialing speed which is
prefixed for each country. The value can range from 50 to 150
milliseconds. The default is 95 milliseconds. The value of register
S11 has no effect on pulse dialing. Defaults and limits are country-
specific.
S12 Escape Guard Time
This register sets the value (in 20 ms increments) of the required
pause after the escape sequence. Range is 0 = 255, default is 50 units
of 0.02 seconds each, or one second.
S28 V.34 Modulation Enable/Disable
This register enables or disables V.34 modulation. Default setting is
1, valid values are 0 or 1. A value of zero disables V.34 modulation.
Any other value in the range enables it.
S30 Inactivity Timer
The value specified by this register sets how long the modem will
wait (in minutes) before disconnecting when no data is sent or
received. This function is only applicable in buffer mode. It is set
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-29
by AT\Tn. Values are 0-255. Default is 0 (disabled).
S34 DTE Throughput Limit
This register specifies whether the modem should limit throughput
when the DTE is operating at higher speeds (57,600 or 115,200bps)
S34=0
Do not limit throughput (default).
Limit throughput to DTE speed.
S34=1
S35 Data Calling Tone
This register enables or disables a tone of a certain frequency and
cadence as specified in V.25 that allows remote data/fax/voice
discrimination. It is set by AT-Cn. The frequency is 1300 Hz with a
cadence of 0.5 seconds on and 2 seconds off. The default is
country-specific. Some countries do not allow data calling tone to be
overridden.
S35=0
S35=1
Data calling tone disabled (default)
Data calling tone enabled
S36 Negotiation Fallback
This register specifies the action to be taken in the event of a
negotiation failure when error control is selected.
S36=0,2
S36=1,3
S36=4,6
S36=5,7
Hang up
Fall back to an asynchronous connection
Attempt MNP. If MNP fails, hang up.
Attempt MNP. If MNP fails, fall back to asynchronous
connection. Default is 7.
S37 Dial Line Rate
S37=0
S37=1
S37=2
S37=3
S37=4
Maximum modem speed (default)
Reserved
1200/75bps
300bps
Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
6-30 PRO/100 LAN+Modem PC Card User’s Guide
S37=5
Attempt to connect at 1200bps
Attempt to connect at 2400bps
Attempt to connect at 4800bps
Attempt to connect at 7200bps
Attempt to connect at 9600bps
Attempt to connect at 12000bps
Attempt to connect at 14400bps
Attempt to connect at 16800bps
Attempt to connect at 19200bps
Attempt to connect at 21600bps
Attempt to connect at 24000bps
Attempt to connect at 26400bps
Attempt to connect at 28800bps
Attempt to connect at 31200bps
Attempt to connect at 33600bps
S37=6
S37=7
S37=8
S37=9
S37=10
S37=11
S37=12
S37=13
S37=14
S37=15
S37=16
S37=17
S37=18
S37=19
S40 ETC Startup Autorating
S40=0
S40=1
S40=2
Start up with normal autorating (default)
Start up at initial rate of 4800 or below
Start up at initial rate of 9600 or below
S42 Auto Rate
V.32bis and V.22bis auto rate is disabled. Retrain operation is disabled or
enabled in date mode, and fallback is disabled in data mode.
S42=0
Auto rate disabled
S42=1
Auto rate enabled (default)
S43 Auto Mode
V.32bis startup auto mode operation disabled.
S43=0
Auto mode disabled
S43=1
Auto mode enabled (default)
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem Reference 6-31
S46 Data Compression Selection
The setting of this register is used to turn data compression on or
off. It is set by AT%Cn.
Data compression can only be enabled when the modem is operat-
ing in an error-control (EC) mode using either V.42 LAP-M or
MNP protocols.
S46=0
Modem will not attempt negotiation for data compres-
sion
S46=2
Modem will negotiate with a remote modem for data
compression (default).
S46=136 Same as S46=0
S46=138 Same as S46=2
S48 LAPM Error Control and Feature Nego-
tiation
S48=7
Negotiation enabled
S48=128 Negotiation disabled; forces immediate fallback options
specified in S36.
The following table shows the S36 and S48 configuration settings needed
to negotiate certain types of connections.
S48=7
S48=128
do not use
buffered
S36=0,2
S36=1,3
S36=4,6
S36=5,7
LAPM or hangup
LAPM or buffered
LAPM, MNP, or hangup MNP or hangup
LAPM, MNP, or buffered MNP or buffered
S89 Timer to Control Sleep Mode
This register displays the number of seconds of inactivity (no
characters sent from DTE, no RING) in the off-line command state
before the modem places itself into standby mode. A value of zero
prevents standby mode. Default is 30. Range is 0 and 5 - 65.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-32 PRO/100 LAN+Modem PC Card User’s Guide
S91 Line Transmit Level
This register is effective only for Japan. It specifies the line transmit
level, in dB, with an implied minus sign. Default is 15 dB, range is 6
- 15.
S92 Direct Connect Transmit Level
This register sets the transmit level, in dBm, for direct connect
cellular. This value may have different settings for different phones.
Default is 0 dBm.
S95 Negotiation Message Options
This register enables various result codes indicating the sequence of
events in an error-controlled connection. This S-Register does not
affect the way the connection is negotiated, it just enables extended
messages.
S95=0
Disables extended result code messages.
S95=1
Use DCE (modem-to-modem) speed when reporting
CONNECT result codes.
S95=2
Append “/ARQ” to CONNECT result code when an
error-controlled (EC) connection is established.
S95=4
S95=8
S95=32
Enable CARRIER result codes.
Enable PROTOCOL result codes.
Enable COMPRESSION result codes.
S98 Cable Detection Options
This register controls the automatic detection and reporting of
changes in the cable or minidock attached to the modem.
S98=0
S98=1
S98=2
Disables cable detection and reporting.
Enable cable detection; disable reporting.
Enable cable detection and reporting.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
Automated Customer Support
You can reach Intel’s automated support services 24 hours a day, every
day at no charge. The services contain the most up-to-date information
about Intel products. You can access installation instructions,
troubleshooting information, and general product information.
World Wide Web &
Internet FTP
Intel Bulletin Board
Service (BBS)
Access Intel’s World Wide Web
home pages or download
information using anonymous FTP.
Use Intel’s BBS. Dial
in by modem at 8-N-1,
and up to 14.4 Kbps.
Troubleshooting
Software updates
Installation notes
Product information
How to access:
✓
✓
✓
✓
✓
See web addresses on next page.
US and Canada:
1-503-264-7999
Europe:
+44-1793-432955
Worldwide:
+1-503-264-7999
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2 PRO/100 LAN+Modem PC Card User’s Guide
Intel Web and Internet Sites
Support: http://support.intel.com
News: news://cs.intel.com
Network Products: http://www.intel.com/network
Corporate: http://www.intel.com
FTP Host: download.intel.com
FTP Directory: \enduser_reseller\etherexpress_lan_adapters
Intel Customer Support Technicians
Other support services: You can purchase a range of support
services, including 24 hour support, per incident support, on-site
service, and software and hardware maintenance agreements. For
details about the Intel Support Service options, download document
8549 from one of the automated services.
Worldwide access: Intel has technical support centers worldwide.
Many of the centers are staffed by technicians who speak the local
languages. For a list of all Intel support centers, the telephone numbers,
and the times they are open, download document 9089 from one of the
automated services.
If you don’t have access to automated services, contact your local
dealer or distributor. Or call +1-916-377-7000 from 07:00 to 17:00
Monday - Friday, U.S. Pacific Time.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
Specifications
General Specifications
Size:
3.37 in x 2.13 in x 0.197 in (85.6 mm x
54.0 mm x 5.0 mm)
Weight:
1.47 oz (42.1 g)
Temperature range:
Operating:
32°F to 131°F (0°C to 55°C)
-4°F to 149°F (-20°C to 65°C)
95% maximum noncondensing
512K flash memory, 160K SRAM
Storage:
Humidity:
Memory size:
Memory alloc.:
4K shared memory allocated to D2000-
D2FFF (default)
Power:
+5 VDC, 490 mA typical
Self test capability
Diagnostics:
Approvals:
FCC Part 15, Class B, FCC Part 68,
Industry Canada, CE Mark
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2 PRO/100 LAN+Modem PC Card User’s Guide
Modem Specifications
Data modulation:
V.34 from 33,600 down to 2400 bps,
V.32terbo with trellis coding at 19200
and 16800 bps; V.32bis (with trellis
coding at 14400, 12000, 9600, and 7200
bps; uncoded at 4800 bps); V.32 (with
trellis coding at 9600 bps, uncoded at
4800 bps); V.23 at 1200/75 and 75/
1200 bps; V.22bis at 2400 bps; V.22 at
1200 bps; Bell 212A at 1200 bps
Fax modulation:
Compatible with Class 1 software; V.17
at 14400, 12000, 9600, 7200, and 4800
bps; V.29 at 9600, 7200, and 4800 bps;
V.27ter at 4800 and 2400 bps
Fax support:
Group 3, EIA/TIA Class 1
Error control:
V.42 Error Control, MNP Levels 2-4
Error Detection
Data compression:
Diagnostics:
V.42bis (4:1) or MNP Level 5 (2:1)
Power-up self tests of program RAM,
data RAM, and nonvolatile memory.
Nonvolatile RAM:
1 user definable profile; 2 thirty-six
digit telephone numbers; LAN Adapter
ID and serial number
Command set:
Data interface:
Hayes and Microcom compatible AT
commands
PCMCIA Release 2.1 compliant, 68-pin
connector
Analog interface:
DTE speeds:
RJ-11C modular telephone connector
1200, 2400, 4800, 7200, 9600, 14400,
19200, 37400, 57600, and 115200 bps
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
Limited Lifetime Warranty
Intel warrants to the original owner that the hardware product delivered
in this package will be free from defects in material and workmanship.
This warranty does not cover the product if it is damaged in the process
of being installed or improperly used.
THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY,
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE ARISING OUT OF ANY
PROPOSAL, SPECIFICATION, OR SAMPLE.
This warranty does not cover replacement of adapter products damaged by
abuse, accident, misuse, neglect, alteration, repair, disaster, improper installation,
or improper testing. If the product is found to be otherwise defective, Intel, at
its option, will replace or repair the product at no charge except as set forth
below, or refund your purchase price provided that you deliver the product
along with a Return Material Authorization (RMA) number (see below), along
with proof of purchase (if not registered), either to the dealer from whom you
purchased it or to Intel with an explanation of any deficiency. If you ship the
product, you must assume the risk of damage or loss in transit. You must use
the original container (or the equivalent) and pay the shipping charge. Intel may
replace or repair the adapter product with either new or reconditioned parts, and
any part or product replaced becomes Intel’s property. Repaired or replaced
products will be returned at the same revision level as received or higher, at
Intel’s option. Intel reserves the right to replace discontinued product with an
equivalent current generation product.
This warranty gives you specific legal rights and you may have other rights
which vary from state to state. All parts or components contained in this
hardware product are covered by Intel’s limited warranty for this product; the
product may contain fully tested, recycled parts, warranted as if new. For
warranty information call one of the numbers below.
Returning a defective product
From North America:
Before returning any product, contact Intel Customer Support and obtain a
Return Material Authorization (RMA) number by calling +1-916-377-7000.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2 PRO/100 LAN+Modem PC Card User’s Guide
If the Customer Support Group verifies that the product is defective, they will
have the RMA department issue you an RMA number to place on the outer
package of the product. Intel cannot accept any product without an RMA
number on the package.
All other locations:
Return the product to the place of purchase for a refund or replacement.
INTEL ADAPTER MONEY-BACK GUARANTEE (North
America Only)
Intel wants you to be completely satisfied with the Intel adapter product that you
have purchased. Any time within ninety (90) days of purchase, you may return
your Intel adapter to the original place of purchase for a full refund of the
purchase price from your dealer. Resellers and Distributors, respectively,
accepting returns and refunding money back to their customers may return Intel
adapters to their original place of purchase. Intel guarantees that it will accept
returns under this policy and refund the original purchase price to customers
purchasing directly from Intel.
Limitation of Liability and Remedies
INTEL SHALL HAVE NO LIABILITY FOR ANY INDIRECT,
SPECULATIVE, CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR
SPECIAL DAMAGES ARISING FROM THE USE OF OR INABILITY TO
USE THIS PRODUCT INCLUDING, WITHOUT LIMITATION, LOSS OF
USE, BUSINESS INTERRUPTIONS, LOSS OF PROFITS, AND LOSS OF
GOODWILL, WHETHER ANY SUCH DAMAGES ARISE OUT OF
CONTRACT NEGLIGENCE, TORT, OR UNDER ANY WARRANTY,
IRRESPECTIVE OF WHETHER INTEL HAS ADVANCE NOTICE OF
THE POSSIBILITY OF ANY SUCH DAMAGES. NOTWITHSTANDING
THE FOREGOING, INTEL’S TOTAL LIABILITY FOR ALL CLAIMS
UNDER THIS AGREEMENT SHALL NOT EXCEED THE PRICE PAID
FOR THE PRODUCT. THESE LIMITATIONS ON POTENTIAL
LIABILITIES WERE AN ESSENTIAL ELEMENT IN SETTING THE
PRODUCT PRICE. INTEL NEITHER ASSUMES NOR AUTHORIZES
ANYONE TO ASSUME FOR IT ANY OTHER LIABILITIES.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you.
Software provided with the hardware product is not covered under the hardware
warranty described above. See the applicable software license agreement which
shipped with the adapter product for details on any software warranty.
April 28, 1994
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX D
Agency Notices
FCC Compliance Statement
FCC Rules and Regulations - Part 15
This product has been tested and found to comply with the limits for a Class B
computing device pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. Installed correctly, it probably will not interfere with radio
or TV reception. However, we do not guarantee the absence of interference.
This product generates and uses energy of about the same frequency as
radio and TV broadcasts. Installed incorrectly, it may interfere with
reception of radio and TV broadcasts.
If you suspect this product is causing interference, turn your computer
on and off while the radio or TV is showing interference. If the
interference disappears when you turn the computer off and reappears
when you turn the computer on, something in the computer is causing
interference.
To reduce interference, try these suggestions:
•
•
Change the direction of the radio or TV antenna.
Move the computer, radio or TV. For example, if the computer is
to the right of the TV, move it to the left of the TV. Or move
them farther apart.
•
•
Plug the computer into a different electrical outlet than the radio
or TV.
Ensure that all expansion slots (on the back or side of the
computer) are covered. Also ensure that all metal retaining
brackets are tightly attached to the computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2 PRO/100 LAN+Modem PC Card User’s Guide
NOTE
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION
If the device is changed or modified without permission from Intel, the
user may void his or her authority to operate the equipment.
FCC Rules and Regulations - Part 68
This equipment complies with Part 68 of the FCC Rules. On the back of the
EtherExpress PRO/100 LAN+Modem PC Card is a label that contains, among
other information, the FCC Registration Number and Ringer Equivalency
Number (REN) for this equipment. You must, upon request, provide this
information to your telephone company.
The REN is useful to determine the quantity of devices you may connect to
your telephone line and still have all those devices ring when your telephone
number is called. In most but not all areas, the sum of the RENs of all devices
connected to one line should not exceed five (5.0). To be certain of the number
of devices you may connect to your line, as determined by the REN, you should
contact your local telephone company to determine the maximum REN for your
calling area.
If your telephone equipment causes harm to the telephone network, the
telephone company may discontinue your service temporarily. If possible, they
will notify you in advance. But if advance notice is not practical, you will be
notified as soon as possible. You will be informed of your right to file a
complaint with the FCC.
Your telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the proper functioning of your
equipment. If they do, you will be notified in advance to give you an opportunity
to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact Intel
Customer Support, at 916-377-7000 for information on obtaining service or
repairs. The telephone company may ask that you disconnect this equipment
from the network until the problem has been corrected or until you are sure that
the equipment is not malfunctioning.
There are no user serviceable parts contained in this equipment.
This equipment may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs.
Download from Www.Somanuals.com. All Manuals Search And Download.
Agency Notices D-3
Canadian compliance (Industry Canada)
When tested in at least one intended host:
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the interference-causing
equipment standard entitled “Digital Apparatus”, ICES-003 of the
Canadian Department of Communications.
Cet appareil numérique respecte les limites bruits radioélectriques
applicables aux appareils numériques de Class B prescrites dans la norme
sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée
par le Ministre Canadien des Communications.
NOTICE: The Industry Canada (IC) label identifies certified equipment. This
certification means that the equipment meets telecommunications network
protective, operational and safety requirements as prescribed in the appropriate
Terminal Equipment Technical Requirements document(s). The department
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by a user to this
equipment, or equipment malfunctions, may give the telephone communications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection, that the electrical ground
connections of the power utility, telephone lines and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminals allowed to
be connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
REN: See back of unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
D-4 PRO/100 LAN+Modem PC Card User’s Guide
Manufacturer declaration
This certifies that Intel EtherExpress PRO/100 Mobile Adapters
comply with the EU Directive 89/336/EEC, using the EMC standards
EN55022 (Class B) and EN50082-1. This product also meets or exceeds
EN60950 safety requirements.
This product has been tested and verified to meet CISPR 22 Class B
requirements.
Intel Corporation
Network Products Division - MS JF3-446
2111 N.E. 25th Ave.
Hillsboro, Oregon 97124
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX E
Software License Agreement
BY USING THIS SOFTWARE, YOU ARE AGREEING TO BE
BOUND BY THE TERMS OF THIS AGREEMENT. DO NOT USE
THIS SOFTWARE UNTIL YOU HAVE CAREFULLY READ AND
AGREED TO THE FOLLOWING TERMS AND CONDITIONS. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT,
PROMPTLY RETURN THE SOFTWARE PACKAGE AND ANY
ACCOMPANYING ITEMS.
LICENSE: Intel Corporation (“Intel”) grants you the non-exclusive
right to use the enclosed software program (the “Software”). You will
not use, copy, modify, rent, sell or transfer the Software or any portion
thereof except as provided in this Agreement.
You may:
1. Install/use the Software on a single computer or on a single local
area network (“LAN”) server;
2. Copy the Software solely for backup or archival purposes,
including copying the Software into memory.
RESTRICTIONS:
You Will Not:
1. Sublicense the Software;
2. Reverse engineer, decompile, or disassemble the Software;
3. Copy the Software, in whole or in part, except as provided in this
Agreement.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2 PRO/100 LAN+Modem PC Card User’s Guide
TRANSFER: You may transfer the Software to another party if the
receiving party agrees to the terms of this Agreement and you retain no
copies of the Software and accompanying documentation. Transfer of
the Software terminates your right to use the Software.
OWNERSHIP AND COPYRIGHT OF SOFTWARE: Title to the
Software and all copies thereof remain with Intel or its vendors. The
Software is copyrighted and is protected by United States and
international copyright laws. You will not remove the copyright notice
from the Software. You agree to prevent any unauthorized copying of
the Software.
DUAL MEDIA SOFTWARE: If the Software package contains
multiple media, you may only use the disks appropriate for your single-
user computer or LAN.
WARRANTY: The Software is provided “AS IS.” Intel warrants that
the media on which the Software is furnished will be free from defects
in material and workmanship for a period of one (1) year from the date
of purchase. Upon return of such defective media, Intel’s entire liability
and your exclusive remedy shall be the replacement of the Software.
THE ABOVE WARRANTIES ARE THE ONLY WARRANTIES
OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
ANY PARTICULAR PURPOSE.
LIMITATION OF LIABILITY: NEITHER INTEL NOR ITS
VENDORS SHALL BE LIABLE FOR ANY LOSS OF PROFITS,
LOSS OF USE, LOSS OF DATA, INTERRUPTIONS OF
BUSINESS, NOR FOR INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND WHETHER
UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
AUDIT: Intel reserves the right to have audits conducted to verify your
compliance with this Agreement.
TERMINATION OF THIS LICENSE: Intel may terminate this
license at any time if you are in breach of any of its terms and
conditions. Upon termination, you will immediately destroy the
Software or return all copies of the Software and documentation to
Intel.
Download from Www.Somanuals.com. All Manuals Search And Download.
Software License Agreement E-3
U.S. GOVERNMENT RESTRICTED RIGHTS: The Software and
documentation were developed at private expense and are provided
with “RESTRICTED RIGHTS.” Use, duplication, or disclosure by the
Government is subject to restrictions as set forth in FAR 52.227-14 and
DFAR 252.227-7013 et seq. or its successor.
EXPORT LAWS: You agree that the distribution and export/re-export
of the Software is in compliance with the laws, regulations, orders or
other restrictions of the U.S. Export Administration Regulations.
APPLICABLE LAW: This Agreement is governed by the laws of the
State of California and the United States, including patent and
copyright laws. Any claim arising out of this Agreement will be
brought in Santa Clara County, California.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-4 PRO/100 LAN+Modem PC Card User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Symbols
100Base-TX Ethernet 1-4
10Base-T Ethernet network 1-4
56Kbps
connections 1-1
technology 1-1
A
Advanced Look-ahead Pipelining 4-45
Alphabetical reference, NOSes 4-3
America Online 5-8
Analog telephone line 1-5
Artisoft LANtastic 4-4
installation 4-4
AT Command Reference 6-4
AT commands
reference 6-1
AT&T StarGROUP
installation 4-4
auto-sensing, speed 1-2
B
Banyan VINES
installation 4-5
Banyan VINES Dial-In 5-10
C
CAB files, Windows 95 2-2
Cabling
data grade 1-2
Card and Socket Services 4-51
Card Information Structure (CIS) 4-48
CARRIER message 6-3
Category 5 cabling 1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-2
COM port
automatic detection 4-33
setting with COMx 4-33
COM Port Monitor 5-5
COMBASE keyword 4-35, 4-43, 4-48, 4-57
COMIRQ keyword 4-35, 4-43, 4-48, 4-57
Communications application notes 5-6
CompuServe WINCIM 5-10
Computer-specific application notes 4-60
COMx keyword 4-33, 4-43
Conflicts, memory 4-35
CONNECT message 6-1
Country Identifier utility 5-1
Country of installation codes 6-21
Customer Support A-1
D
Data compression 4-31
DCOMPVLM.BAT 4-19, 4-26, 4-30
DEC PATHWORKS 4-6
Default values 4-3
Diagnostics 5-3
Dial modifiers 6-6
Dial-Up Product Registration 5-2
Digital telephone line 1-5
Digital telephone lines 1-7
DOS modem software 4-57
E
Early receive (RX) 4-45
Early transmit (TX) 4-46
EMM386 4-35, 4-36, 4-51
EMMEXCLUDE= statement 4-36
Error control 4-31
F
Fax/modem 4-31
FRAME keyword 4-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-3
FTP LANWatch
installation 4-9
NDIS driver 4-10
Packet driver 4-10
FTP PC/TCP 4-11
and NetWare 4-15
installation 4-11
Packet driver 4-14
G
Generic installation 4-16
H
Hardware installation requirements 1-3
Hayes 4-31
Hayes commands 6-1
Heat during normal use 1-6
HotSwap 1-3
HP LAN Manager
installation 4-16
I
IBM DOS LAN Requestor 4-19
IBM Local Area Network Support Program 4-16
installation 4-16, 4-17
IBM Local Area Support Program 4-16
IBM PC LAN 4-19
Indicator lights
LAN adapter cable 1-8
modem cable 1-7
Installation
generic 4-16
manual 4-19
Microsoft Windows 3.x 4-2
Novell NetWare 4-2
Program, Intel 4-2
Program, Xircom 4-22
VLM shell 4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-4
Installation Program 1-2, 4-3
Intel Web and Internet Sites B-2
INTERRUPT keyword 4-44, 4-48
INTERRUPTNUMBER keyword 4-44
IOADDRESS keyword 4-44
IOBASEADDRESS keyword 4-44
IOWAITSTATES keyword 4-44
K
K56flex technology 1-1
L
LAN card 4-31
LAN Manager
Microsoft LAN Manager 4-20
Ungermann-Bass Net/One 4-28
LANtastic, Artisoft 4-4
LANWatch, FTP 4-9
LapLink 5-11
LEDs
LAN adapter cable 1-8
modem cable 1-7
LINKDISABLE keyword 4-44
LINKINTEGRITY keyword 4-44
Lotus
cc:Mail 5-13
Notes 5-15
M
M16BTEST.EXE 5-3
Manual installation 4-19
Memory
conflicts 4-35
keyword 4-45
manager 4-35
MEMORYBASEADDRESS keyword 4-45
MEMWAITSTATES keyword 4-45
Microcom 4-31
Microsoft
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-5
Windows for Workgroups. See Windows for Workgroups
Microsoft LAN Manager
installation 4-20
Microsoft Remote Access Server (RAS) 5-17
Microsoft Windows 3.x
installation 4-2
MODE keyword 4-45, 4-47
Models 1-2
Modem
driver 4-36
driver example 4-37
driver parameters 4-36
reference information 4-31
sound 4-60
volume levels 4-60
Modem commands 6-4
Modem result codes 6-1
Modem script files 5-6
Modem setup 5-7
Modem Test utility 5-2
MODEMLOG.TXT 2-12
N
NDIS 3.0 driver
parameters 2-13, 3-8
NDIS driver
Artisoft LANtastic 4-4
FTP LANWatch 4-9
FTP PC/TCP 4-11
generic 4-16
Microsoft LAN Manager 4-20
Microsoft Windows for Workgroups 4-21
parameters 4-40
SunSoft PC-NFS 4-27
Ungermann-Bass Net/One LAN Manager 4-28
Wollongong PathWay Access for DOS 4-29
NET.CFG file 4-38
example 4-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-6
NetWare. See Novell NetWare
installation with Windows 95 2-8
Network
drivers 4-3
operating system 1-2, 4-3
network node address 5-4
NETX shell support 4-2
NO CARRIER message 6-1
NOCHECK keyword 4-45
NOCOM keyword 4-45
NOLEDS keyword 4-46
Novell NetWare 4-26
and FTP PC/TCP 4-15
installation 4-2
O
ODI driver
FTP PC/TCP 4-11
generic 4-16
loading sequence 4-39
Microsoft Windows for Workgroups 4-21
parameters 4-38
Wollongong PathWay Access for DOS 4-29
OEM Service Release Version 2 2-1
OK message 6-1
OnNet with FTP PC/TCP 4-11, 4-13
OSR2 2-1
P
PABX systems 1-7
Package contents 1-4
Packet driver
FTP LANWatch 4-9
FTP PC/TCP 4-11
loading sequence 4-42
parameters 4-41
Parameters, driver 2-13, 3-8, 4-1, 4-11, 4-19, 4-37
PATHWORKS, DEC 4-6
PC Card slot 1-5
PC Card Standard 1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-7
PC-NFS 4-27
PC/TCP, FTP 4-11
PCMCIA 1-2
PORT keyword 4-46
Power management 1-3
Power-saving modes
under Windows 95 2-9
Prodigy 5-19
PROTOCOL.INI file 4-40
R
Registry
Windows 95 2-16, 3-8
Windows NT 2-13
Required Equipment 1-4
Result codes, modem 6-1
Retail version, Windows 95 2-1
S
S-Register Reference 6-25
S-Registers 6-25
Script files, modem 5-6
Self test 5-3
SHAREIRQ keyword 4-35, 4-46, 4-57
Shutdown and restart 2-11
SINT keyword 4-46
SLOT keyword 4-46
SOCKET keyword 4-46, 4-47
Software supplied 1-2
Software updates B-1
SunSoft PC-NFS
installation 4-27
SYSTEM.INI file 4-36
T
TELSEL.EXE 5-1
Troubleshooting
Windows 95 2-9
Type II PC Card 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-8
U
Ungermann-Bass Net/One
installation 4-28
Update Device Driver Wizard 2-5
Utilities 5-1
V
Version
Windows 95 2-1
VINES, Banyan 4-5
VLM file decompression 4-19
VLM shell 4-2
Volume, modem speaker 4-60
W
WinCim 5-10
Windows 3.1
installation 4-2
Windows 95 2-1
installation 2-1
troubleshooting 2-9
NetWare installation 2-8
OEM (OSR2) version 2-4
retail version 2-2
Windows NT
installation 3-3
Windows for Workgroups 4-21
ODI driver 4-22
removing old installation 4-25
with NetWare 4-22
Wizard, Update Device 2-5
Wollongong PathWay Access
installation 4-29
Wollongong PathWay Access for DOS 4-29
NDIS driver 4-30
ODI driver 4-30
WORDSIZE keyword 4-46, 4-47
World Wide Web B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|