Digital Light Processing Projector
DLV-100
Instruction Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
These safety instructions are to ensure the long life of
your projector and to prevent fire and shock. Please read
them carefully and heed all warnings.
CAUTION
Do not unplug the power cable from the wall outlet under any
one of the following circumstances. Doing so can cause damage
to the projector:
* While the Hour Glass icon appears.
Installation
* While the message "Please wait a moment." appears. This mes-
sage will be displayed after the projector is turned off.
* Immediately after the power cable is plugged into the wall
outlet (the POWER indicator has not changed to a steady or-
ange glow).
* Immediately after the cooling fan stops working (The cooling
fan continues to work for 90 seconds after the projector is
turned off with the POWER button).
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away
from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters
or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm in-
ternal components.
* While the POWER and the STATUS indicators are alternately
flashing.
5. Handle your projector carefully. Dropping or jarring can dam-
age internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
Power Supply
1. The projector is designed to operate on a power supply of
100-120 or 200-240 V 50/60 HzAC. Ensure that your power
supply fits this requirement before attempting to use your
projector.
2. Handle the power cable carefully and avoid excessive bend-
ing. A damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of
time, disconnect the plug from the power outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily
soiled, use a mild detergent. Never use strong detergents
or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful
not to scratch or mar the lens.
Lamp Replacement
•
To replace the lamp, follow all instructions provided on page
44.
•
Be sure to replace the lamp when the message "The lamp
has reached the end of its usable life. Please replace
the lamp.!!" appears. If you continue to use the lamp after
the lamp has reached the end of its usable life, the lamp
bulb may shatter, and pieces of glass may be scattered in
the lamp case. Do not touch them as the pieces of glass
may cause injury. If this happens, contact your Integra dealer
for lamp replacement.
•
Allow a minimum of 90 seconds to elapse after turning off
the projector. Then disconnect the power cable and allow 60
minutes to cool the projector before replacing the lamp.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are
unobstructed to prevent the build-up of heat inside your pro-
jector. Allow at least 3 inches (10 cm) of space between
your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of pa-
per from falling into your projector. Do not attempt to re-
trieve any objects that might fall into your projector. Do not
insert any metal objects such as a wire or screwdriver into
your projector. If something should fall into your projector,
disconnect it immediately and have the object removed by a
qualified Integra service personnel.
3. Do not place any liquids on top of your projector.
•
•
Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
Keep any items such as magnifying glass out of the light
path of the projector. The light being projected from the lens
is extensive, therefore any kind of abnormal objects that
can redirect light coming out of the lens, can cause unpre-
dictable outcome such as fire or injury to the eyes.
•
Do not cover the lens with the supplied lens cap or equiva-
lent while the projector is on. Doing so can lead to melting of
the cap and possibly burning your hands due to the heat
emitted from the light output.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. INTRODUCTION
Setup........................................................................ 35
Orientation ........................................................... 35
Cinema position................................................... 35
Background ......................................................... 35
Mouse .................................................................. 36
Button/Sensitivity.............................................. 36
PC Card Viewer Options ..................................... 36
Capture Options .................................................. 36
Signal Select........................................................ 36
Auto Adjust (RGB only)........................................ 36
Auto Start............................................................. 37
Power Management ............................................ 37
Power Off Confirmation ....................................... 37
Keystone Save .................................................... 37
White Segment .................................................... 37
Clear Lamp Hour Meter ....................................... 37
Communication Speed ........................................ 37
Default Source Select .......................................... 37
Control Panel Key Lock ....................................... 37
Introduction to the Projector DLV-100............................. 6
Getting Started ............................................................... 6
What’s in the Box............................................................ 7
Getting to Know Your Projector DLV-100........................ 8
Front / Side Features ................................................. 8
Attaching the lens cap................................................ 8
Rear / Side Features .................................................. 9
Top Features ............................................................ 10
Terminal Panel Features ........................................... 11
Remote Control Features......................................... 12
Remote Control Battery Installation ..................... 13
Operating Range ................................................. 13
Remote Control Precautions ............................... 13
2. INSTALLATION
Setting Up Your Projector ............................................. 14
Selecting a Location ..................................................... 14
Screen and Projection Distance ................................... 14
Distance Chart .............................................................. 15
Reflecting the Image..................................................... 15
Wiring Diagram ............................................................. 16
Connecting Your PC................................................. 17
Connecting Your Macintosh Computer .................... 18
Connecting Your DVD Player ................................... 19
Connecting Your VCR or Laser Disc Player............. 20
About Startup screen (Menu Language Select screen) .......... 21
Tools ............................................................................. 38
Capture .................................................................... 38
PC Card Files........................................................... 38
Changing Background Logo .................................... 38
Chalk Board ............................................................. 39
Information.................................................................... 39
3. OPERATION
Using the PC Card Viewer Function ............................. 40
Features ................................................................... 40
Inserting and Ejecting a CompactFlash™ Card ....... 40
Operating the PC Card Viewer Function
Connecting the Power Cable and Turn on the Projector .............. 22
Basic Operation ............................................................ 25
Using the Menus........................................................... 27
Menu Tree .................................................................... 29
Menu Elements............................................................. 30
Menu Descriptions & Functions .................................... 31
Source Select ............................................................... 31
RGB/Video/S-Video/PC Card Viewer
from the Projector (playback) ............................... 41
Capturing Images Displayed on the Projector ......... 42
Viewing Digital Images............................................. 42
Terminology.............................................................. 43
Picture .......................................................................... 31
Brightness/Contrast/Color/Hue/Sharpness
4. MAINTENANCE
Replacing the Lamp...................................................... 44
Volume.......................................................................... 31
Image Options .............................................................. 32
Keystone .................................................................. 32
Lamp Mode .............................................................. 32
Aspect Ratio............................................................. 32
Noise Reduction....................................................... 33
Position/Clock .......................................................... 33
Resolution ................................................................ 33
Video Filter ............................................................... 33
Factory Default......................................................... 33
Color Management ....................................................... 34
Gamma Correction................................................... 34
Color Matrix.............................................................. 34
White Balance .......................................................... 34
Projector Options .......................................................... 34
Menu ........................................................................ 34
Menu Mode.......................................................... 35
Advanced Menu, Basic/Custom Menu ............. 35
Language ............................................................ 35
Projector Pointer.................................................. 35
Menu Display Time .............................................. 35
Source Display .................................................... 35
Direct Button (Volume Bar) .................................. 35
5. TROUBLESHOOTING
Status Light Messages ................................................. 45
Common Problems & Solutions.................................... 45
When using the PC Card Viewer function .................... 46
6. SPECIFICATIONS
Optical/Electrical/Mechanical........................................ 47
Cabinet Dimensions ..................................................... 48
D-Sub Pin Assignments ................................................ 49
Timing Chart ................................................................. 50
PC Control Codes......................................................... 51
Cable Connection ......................................................... 51
CompactFlash is a trademark of San Disk Corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INTRODUCTION
Introduction to the Projector DLV-100
This section introduces you to your new Projector and describes the
features and controls.
• The supplied remote control can be used without a cable.
• You can control the projector with a PC using the PC Control
port.
• USB terminal allows USB mouse operation*3.
• The contemporary cabinet design is light, compact, easy to carry,
and complements any office, boardroom or auditorium.
Congratulations on Your Purchase of The Projector DLV-100
The DLV-100 is one of the very best projectors available today. The
DLV-100 enables you to project precise images up to 200 inches across
(measured diagonally) from your PC or Macintosh computer (desk-
top or notebook), VCR, DVD player, document camera, a laser disc
player or PC Card Viewer.
You can use the projector on a tabletop or cart, you can use the pro-
jector to project images from behind the screen, and the projector can
be permanently mounted on a ceiling*1. The remote control can be
used wirelessly.
*1 Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the pro-
jector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
*2 A UXGA (1600
ן 1200) and SXGA image (1280ן 1024) are displayed.
*3 The USB terminal meets the USB1.1 specification and accepts a
USB mouse only.
Features you’ll enjoy:
• Simple set up and operation.
• A high-performance 135 watt NSH lamp.
• The supplied wireless remote control that operates the projector
from the front or rear.
• The image can be projected between 30 and 200 inches (mea-
sured diagonally).
• Keystone correction allows you to correct trapezoidal distortion
so that the image is square.
• You can choose between video modes depending on your source:
"normal" for a typical picture, "natural" for true color reproduc-
tion.
Getting Started
The fastest way to get started is to take your time and do everything
right the first time. Take a few minutes now to review the instruction
manual. This may save you time later on. At the beginning of each
section of the manual you’ll find an overview. If the section doesn’t
apply, you can skip it.
• The built-in PC Card Viewer allows you to start your presenta-
tion even when a PC is not available at the site.
• The "Capture" enables you to capture the current projected im-
age.
• An image can be projected from in front or behind a screen, and
the projector can even be installed on the ceiling.
• An exclusive Advanced AccuBlend intelligent pixel blending
technology - an extremely accurate image compression technol-
ogy - offers a crisp image with UXGA (1600
ן 1200) resolu- tion*2.
• Supports most IBM VGA, SVGA, XGA, SXGA/UXGA (with
AdvancedAccuBlend)*2, Macintosh, component signal (YCbCr
/YPbPr) or any other RGB signals within a horizontal frequency
range of 15 to 100 kHz and a vertical frequency range of 50 to
120 Hz. This includes NTSC, PAL, PAL-N, PAL-M, PAL60,
SECAM and NTSC4.43 standard video signals.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector DLV-100.
L E C
N
A
C
R
E
T
C T
L E
N
E
S E
C E S S
A C
U
J U S T
A D
N
E
M
A U T O
C A R D
C
P
C E
O U R
S
B Y
/
S T A N D
O N
E R
O W
P
T U S
S T A
Projector
Lens cap
Soft carrying case
Batteries
INPUT
String and rivet
Remote control
RGB signal cable
Power cable
Registration
Card
Quick
Connect
Guide
Instruction
Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know Your Projector DLV-100
Front/ Side Features
Controls
L E
C
N
A
C
R
E
T
N
E
S E L E C T
A C C E S S
U
N
E
M
A D J U S T
A U T O
C A R D
P C
S O U R C E
/
S T A N D B Y
O N
P O W E R
S T A T U S
Ventilation (inlet)
Adjustable Tilt Foot
Adjustable Tilt Foot Button
Zoom Ring
Focus Ring
Remote Sensor
Lens Cap
Lens
Attaching the lens cap to the lens hood with the supplied string and rivet
1. Thread the string through the hole on the lens cap and then tie a knot in the string.
2. Use the rivet to attach the string to the bottom of the lens hood.
Attaching the lens cap
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear/ Side Features
Monaural Speaker (1W)
STATUS
POWER
ON
STAND BY
/
SOURCE
AUDIO
PC
CARD
AUTO
ADJUST
ACCESS
M
E
N
U
SELECT
RGB
E
N
T
E
S-VIDEO
PC CONTROL
R
C
A
N
C
EL
VIDEO
Ventilation (inlet)
Remote Sensor
USB
PC CARD
AC IN
Ventilation (outlet)
Heated air is exhausted from here
Terminals and PC card
AC Input
Rear Foot
Slot for Kensington
MicroSaver
Security System
Spacer (black rubber)
Bottom
Spacer (black rubber)
To fine-adjust the height of the rear
foot, remove the spacer and rotate
the rear foot to the desired height.
Rear Foot
Rotate to fine-adjust horizontally
position
Lamp cover
Ventilation (inlet)
Lamp cover screw
Rear Foot
(not adjustable)
NOTE: The projector has an internal temperature sen-
sor. The sensor controls the speed of the fan to keep
constant temperature in the inside.
When the internal temperature rises, the built-in fan au-
tomatically runs at a high speed (high-speed mode).
During this time, the sound of exhaust may be heard.
This is not a malfunction.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Top Features
STATUS
POWER
4
ON
STAND BY
/
10
5
SOURCE
3
9
1
AUDIO
PC
CARD
AUTO
ADJUST
ACCESS
M
E
N
U
SELECT
RGB
E
N
T
E
S-VIDEO
R
PC CONTROL
C
A
N
C
E
L
VIDEO
6
7
USB
8
PC CARD
1. Power Button (ON / STAND BY)
5. Auto Adjust Button (RGB only)
Use this button to turn the power on and off when the power is
supplied and the projector is in standby mode.
Use this button to adjust Position-H/V and Pixel Clock/Phase for
an optimal picture. Some signals may not be displayed correctly or
take time to switch between sources.
2. Status Indicator
When this is lit red continually, it's warning you that the projection
lamp has exceeded 1500 hours (1000 hours in High-Bright mode)
of service. After this light appears, it is advisable to replace the
projection lamp as soon as possible. (See page 44). In addition the
message "The lamp has reached the end of its usable life. Please
replace the lamp!!." appears continually until the lamp is replaced.
If this light blinks red rapidly, it indicates that the lamp cover is not
attached properly or the projector is overheated.
6. PC Card Access Indicator
Lights while accessing a CompactFlash memory card.
7. Enter Button
Executes your menu selection and activates items selected from
the menu.
8. Cancel Button
See the Power/Status Light Messages on page 45 for more details.
Press this button to exit "Menus". Press this button to return the
adjustments to the last condition while you are in the adjustment
or setting menu.
3. Power Indicator (
)
When this indicator is green, the projector is on; when the indica-
9. Select (LMꢀ ᮣ) / Volume (+) (–) Buttons
LM: Use these buttons to select the menu of the item you wish
to adjust.
tor is orange, it is in standby mode.
4. Source Button
When no menus appear, these buttons work as a volume
control.
ꢀ ᮣ: Use these buttons to change the level of a selected menu
item.
Use this button to select a video source such as a PC, VCR, DVD
player or PC Card Viewer (CompactFlash card).
Each time this button is pressed, the input source will change as
follows:
A press of the ᮣ button executes the selection.
When the menus or the Viewer tool bar is not displayed,
these buttons can be used to select a slide, or to move the
cursor in Folder List or Slide List.
→ RGB → Video → S-Video → PC Card Viewer
If no input signal is present, the input will be skipped.
When the magnifying glass is displayed, these LMꢀ ᮣ
buttons move the magnifying glass.
10. Menu Button
Displays the menu.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal Panel Features
S
WER
1
ON
STAND BY
/
2
SOURCE
3
4
AUDIO
PC
CARD
AUTO
ADJUST
ACCESS
M
E
N
U
SELECT
RGB
E
N
T
5
E
S-VIDEO
R
PC CONTROL
C
A
N
C
E
L
6
VIDEO
USB
PC CARD
7
AC IN
8
1. Audio Input Mini Jack (3.5 mm ∅)
This is where you connect audio output from your computer,VCR,
DVD player or laser disc player.
A commercially available audio cable is required.
9
10
2. RGB Input/ Component Input Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment such as IBM or com-
patible computers. Use the supplied RGB cable to connect to a PC.
Or connect a Macintosh computer here using the supplied RGB
cable. This also serves as a component input connector that allows
you to connect a component video output of component equip-
ment such as a DVD player.
If you are writing your own program, typical PC control codes are
on the back cover page.
A cap is put on the port at the factory. Remove the cap when using
the port.
3. S-Video Input (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external source
like a VCR.
8. USB Terminal
Connect a commercially available mouse that supports USB. You
can operate the menu or PC Card Viewer with the USB mouse via
this terminal.
NOTE: S-Video provides more vivid color and higher resolution than the
traditional composite video format.
Note that this terminal is not used with a computer and that there
may be some brands of USB mouse that the projector does not
support.
4. Video Input (RCA)
Connect a VCR, DVD player, laser disc player, or document cam-
era here to project video.
9. AC Input
5. PC Card Eject Button
Connect the supplied power cable's three-pin plug here. When you
plug the other end into an active wall outlet, the POWER indicator
turns orange and the projector is in standby mode.
Press to eject a CompactFlash memory card.
6. PC Card Slot
Insert a CompactFlash memory card here.
10. Built-in Security Slot (
)
This security slot supports the MicroSaver® Security System.
MicroSaver® is a registered trademark of Kensington Microware
Inc.
7. PC Control Port (Mini DIN 8 Pin)
Use this port to connect your PC to control your projector via a
serial cable. This enables you to use your PC and serial communi-
cation protocol to control the projector.
The logo is trademarked and owned by Kensington Microware Inc.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Features
Supplied Remote Control
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projec-
tor cabinet.
1
2
2. Standby/On Button
If the main power is applied, you can use this button to turn your
projector on or put it in standby.
INPUT
3
4
5
6
3. S-Video Button
Press this button to select an S-Video source from a VCR.
4. Video Button
Press this button to select an NTSC, PAL, SECAM or NTSC4.43
compatible video source from aVCR, DVD player, laser disc player
or document camera.
7
8
11
12
13
9
10
14
5. RGB Button
Press this button to select a video source from computer or compo-
nent equipment connected to your RGB port.
15
6. Auto Adjust Button
17
Use this button to adjust an RGB source for an optimal picture.
Some signals may not be displayed correctly or take time to switch
between sources.
16
7. Magnify + - Buttons
Use this button to adjust the image size up to 400%.
To change the position of the magnified screen, press one of the
ꢀ ᮣ
ꢀ
LM
ᮣ
buttons to recall the magnifying glass, then use the LM
buttons to move the screen.
ꢀ ᮣ
15. LM
(Select) Buttons
8. Volume + - Buttons
L,M: Use these buttons to select the menu of the item you wish
Press + button to increase the volume and - button to decrease
to adjust.
ꢀ ᮣ
,
it.
:
Use these buttons to change the level of a selected menu
item.
ᮣ
9. ASPECT Button
A press of the button executes the selection.
ꢀ ᮣ
Press this button to select the screen size.
When the magnifying glass is displayed, these LM
buttons move the magnifying glass.
10. Mute Button
This button turns off an image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an image
and sound without turning off the menu.
16. Cancel Button
Press this button to exit "Menus". Press this button to return to the
previous menu without storing the current settings or adjustments
when you are in the submenu or adjustment screen.
11. PICTURE Button
17. Enter Button
Press this button to recall and display the screen-related menu.
Press this button to execute the selected item. When this is pressed,
the adjustments and settings are saved, and the display is returned
to the menu.
12. Freeze Button
This button will freeze a picture. Press again to resume motion.
13. Menu Button
Displays the menu for various settings and adjustments.
14. LAMP RESET Button
If the lamp has been turned on for more than 1,600 hours (Normal
mode), the power to the unit will be cut off and no messages will
be displayed. Press and hold down this button for 10 seconds or
more while the unit is in stand-by mode to clear the lamp available
time and the lamp usage time.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Battery Installation
Operating Range
The infrared signal operates by line-of-sight up to a distance of ap-
proximately 22 feet (7m) and within a 60-degree angle of the remote
sensor. The projector will not function if there are objects between
the remote control and the remote sensor on the projector or if strong
light falls on the remote sensor. A weak battery will also prevent the
projector from operating
Remove the battery compartment cover by pressing the tab
and lifting up the cover.
1
7m
30˚
30˚
7m
30˚
30˚
Insert two AA-size batteries into the battery compartment.
Carefully follow the polarity diagram (positive + and nega-
tive - symbols) inside the battery compartment.
2
This sample may be slightly different from actual range
Replace the compartment cover.
3
Do not mix different types of batteries or new and old batteries.
Remote Control Precautions
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove
the batteries.
•
Do not place the batteries upside-down.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. INSTALLATION
This section describes how to set up your projector DLV-100 and how to connect video and audio sources.
Setting up Your Projector
Your Projector DLV-100 is simple to set up and use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you can project your image.
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens with the lens cap.
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 30" (0.8 m)
measured diagonally when the projector is roughly 4 feet (1.3 m) from the wall or screen. The largest the image can be is 200" (5.1 m) when the
projector is about 29 feet (8.8 m) from the wall or screen.
Screen and Projection Distance
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
Screen size (Unit: cm / inch)
Throwing distance
406.4(W) X 304.8(H) / 160(W) X 120(H)
365.8(W) X 274.3(H) / 144(W) X 108(H)
Screen
304.8(W) X 228.6(H) / 120(W) X 90(H)
200"
243.8(W) X 182.9(H) / 96(W) X 72(H)
180"
203.2(W) X 152.4(H) / 80(W) X 60(H)
150"
162.6(W) X 121.9(H) / 64(W) X 48(H)
120"
121.9(W) X 91.4(H) / 48(W) X 36(H)
100"
81.3(W) X 61.0(H) / 32(W) X 24(H)
61.0(W) X 45.7(H) / 24(W) X 18(H)
80"
Unit: m / inch
60"
Lens center
30"
40"
1.3 / 51
1.7 / 67
2.6 / 102
3.5 / 138
4.4 / 173
5.3 / 209
7.9 / 311
6.6 / 260
8.8 / 346
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance Chart
C
Lens Center
D
Throw Distance
α
Screen Top
B
Lens Offset from Center of Projector
Screen Center
2.97” (75.5mm)
C
Throw Distance
Screen Center
B
Screen Bottom
1.5”(38mm)
α
D
Lens Center
Projector feet
B=Vertical distance between lens center and screen center
C=Throw distance
D=Vertical distance between lens center and top of screen (bottom of screen for desktop)
α=Throw angle
NOTE: Distances may vary +/-5%.
Screen Size
Width
α
C
D
B
Diagonal
Height
Wide
Tele
Wide
Tele
degree
12.3
12.1
12.1
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
11.9
11.9
inch mm inch mm inch mm inch mm inch mm
30 762 24 610 18 457 12 307 46 1160
40 1016 32 813 24 610 16 409 61 1560
60 1524 48 1219 36 914 24 613 93 2360
67 1702 54 1361 40 1021 27 685 104 2640
72 1829 58 1463 43 1097 29 736 112 2850
80 2032 64 1626 48 1219 32 818 125 3170
84 2134 67 1707 50 1280 34 859 131 3330
90 2286 72 1829 54 1372 36 920 141 3570
100 2540 80 2032 60 1524 40 1022 156 3970
120 3048 96 2438 72 1829 48 1227 188 4770
150 3810 120 3048 90 2286 60 1533 235 5980
180 4572 144 3658 108 2743 72 1840 283 7190
200 5080 160 4064 120 3048 80 2045 315 7990
–
–
–
–
–
–
–
–
–
–
–
–
–
–
inch mm inch mm degree
–
–
–
–
–
–
–
–
–
–
–
–
–
–
56 1410
75 1900
113 2870
126 3210
136 3450
151 3840
159 4040
170 4330
3
4
6
7
7
8
9
9
78
14.8
104 14.7
156 14.6
174 14.5
187 14.5
208 14.5
219 14.5
234 14.5
189 4810 10 260 14.4
228 5790 12 312 14.4
285 7240 15 390 14.4
343 8700 18 469 14.4
381 9670 20 521 14.4
Reflecting the Image
Ceiling Installation
Using a mirror to reflect your projector’s image enables
you to enjoy a much larger image. Contact your Integra
dealer if you need a mirror. If you’re using a mirror and
your image is inverted, use the “Menu” and “Select” but-
tons on your projector cabinet or LM buttons on your
remote control to correct the orientation. (See page 35.)
WARNING
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls to the
ground, you can be injured and the projector severely damaged.
• Do not use the projector where temperatures vary greatly. The projector
must be used at temperatures between 41˚F (5˚C) and 95˚F (35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will harm the
screen image.
• Ensure that you have adequate ventilation around your projector so heat can
dissipate. Do not cover the vents on the side or the front of the projector.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
To video, S-video, and audio
inputs on the projector.
VCR, DVD Player or LaserDisc Player
AUDIO
Document Camera
RGB
S-VIDEO
VIDEO
RGB Signal cable (supplied)
To mini D-Sub 15-pin connector on the
PC CONTROL
projector. It is recommended that you use a
commercially available distribution amplifier if
connecting a signal cable longer than the
supplied cable.
Optional Component V cable
DVD Player (with component output)
IBM VGA or Compatibles
(Desktop type or notebook type)
Macintosh
(Desktop type or notebook type)
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
NOTE:
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.
NOTE: If using video, S-video, or audio cables, the cables should be 3 m (9.8 feet) or shorter.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your PC
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recom-
mended that you use a commercially available distribution ampli-
fier if connecting a signal cable longer than the supplied one.
IBM VGA or Compatibles
(Notebook type)
S
T
A
T
P
U
S
O
W
E
R
O
N
S
/
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
P
C
D
IO
C
A
A
M
E
U
U
R
A
T
O
D
D
N
U
J
A
C
S
C
T
E
S
S
R
S
E
G
E
B
L
N
E
C
T
T
S
E
-V
ID
R
E
O
P
C
C
O
C
A
N
N
C
E
L
T
R
O
L
V
ID
E
O
U
AUDIO
RGB INPUT
AUDIO
RGB
S-VIDEO
PC CONTROL
IBM VGA or Compatibles
(Desktop type)
VIDEO
Audio cable
(not supplied)
Connecting your PC to your projector DLV-100 will enable you to project your computer’s screen image for an impressive presentation.
To connect to a PC, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC to the projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you’ve connected to the
projector.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Macintosh Computer
Macintosh (Notebook type)
S
T
A
T
P
U
S
O
W
E
R
O
N
S
/
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
P
C
D
I
O
C
A
A
M
E
U
U
R
A
T
O
D
D
N
U
A
C
J
S
T
C
E
S
S
R
S
E
G
E
B
L
N
E
C
T
T
S
E
-
V
ID
R
E
O
P
C
C
O
C
A
N
N
C
E
L
T
R
O
L
V
ID
E
O
RGB Signal cable
(supplied)
AUDIO
RGB INPUT
AUDIO
GB
S-VIDEO
PC CONTROL
Audio cable
VIDEO
(not supplied)
Macintosh (Desktop type)
NOTE: The new Macintosh computer
such as G3 will have the 15 pin HD con-
nector. The DLV-100's "Plug and Play"
data will be downloaded to the
Macintosh. Therefore, a Mac adapter
will not be necessary.
To connect to a Macintosh, simply:
1. Turn off the power to your projector and your Macintosh com-
puter.
IP
4
D
5
6
N
O
3
2
1
2. Use the supplied signal cable to connect your Macintosh com-
puter to the projector.
3. Turn on the projector and the Macintosh computer.
For older Macintosh,
use a commercially
available pin
adapter to connect to
your Mac's video
port.
Pin adapter for Macintosh
(not supplied)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your DVD Player
S
T
A
T
P
U
S
O
W
E
DVD player
R
O
N
S
/
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
P
C
D
I
O
C
A
A
M
E
U
U
R
A
T
O
D
D
N
U
A
C
J
S
T
C
E
S
S
R
S
E
G
E
B
L
N
E
CT
L
T
S
E
-
V
I
D
R
E
O
P
C
C
O
C
A
N
N
C
E
T
R
O
L
V
ID
E
O
U
RGB INPUT
Y
Cb Cr
AUDIO
Cr
R
L
B
Cb
S-VIDEO
Y
PC CONTROL
White
VIDEO
Red
15-pin-to-RCA
ן 3 cable (not supplied) (Component V )
Audio Equipment
Audio cable
(not supplied)
R
L
White
Red
You can connect your projector to a DVD player with component outputs or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use the 15-pin-to-RCA
ן 3 cable (not supplied) to connect your DVD player to the RGB INPUT connector on the projector.
For a DVD player without component video (Y,Cb,Cr) outputs, use common RCA cables (not provided) to connect a composite VIDEO
output of the DVD player to the Video Input of the projector.
3. Turn on the projector and DVD player.
NOTE: Refer to your DVD player’s instruction manual for more information about your DVD player’s video output requirements,
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your VCR or Laser Disc Player
VCR/ Laser disc player
S
T
A
T
P
U
S
O
W
E
R
O
N
S
/
T
A
N
D
B
Y
S
O
U
R
C
E
AUDIO
P
C
C
A
M
E
A
U
U
R
A
T
O
D
D
N
U
J
A
C
S
T
C
E
S
S
RGB
S
E
E
LE
N
C
T
T
S-VIDEO
E
R
PC CONTROL
C
A
N
C
EL
S-VIDEO
AUDIO
VIDEO
R
L
S-video cable
(not supplied)
RGB
TROL
White
VIDEO
Red
Audio equipment
Document camera
Audio cable
(not supplied)
VIDEO
R
L
White
Red
Video cable (not supplied)
Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the
Video input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio
equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo
sound.
3. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player instruction manual for more information about your equipment’s video output requirements.
NOTE:
• The image from a video playback deck may not be correctly displayed when used with a scan converter before being input to the projector.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
About Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen.
This screen gives you the opportunity to select one of the seven menu
languages: English, German, French, Itilan, Spanish,Swedish and
Japanese.
To select a menu language, follow these steps:
1. Use the Select L or M button to select one of the seven languages
for the menu.
2. Press the Enter button to execute the selection.
3. The Basic/Custom menu will be displayed in the language you
have selected.
To close the menu, press the Cancel button.
After this has been done, you can proceed to the advanced menu
operation.
If you want, you can select the menu language later. See “Language”
on page 34.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3.OPERATION
NOTE: Do not disconnect the power cable during this time. Then, unplug the
power cable. The power indicator will go out.
Connecting the Power Cable and Turn on the Projector
Before you turn on your projector, ensure that the computer or video
Status of indicator light: turn on
source is turned on and that your lens cap is removed.
Normal mode:
stand by
Connect the supplied power cable to the projector.
1
STATUS
ON/STAND BY
POWER
U
N
E
M
L
E
C
steady orange light
SELECT
AN
C
R
E
N
T
E
AUTO
ADJUST
ACCESS
CARD
PC
STATUS
POWER
STATUS
SOURCE
POWER
/
AC IN
ON
STAND BY
PC CARD
STATUS
POWER
VIDEO
steady green light
flashing green light
for one minute.
High-Bright mode:
AUDIO
stand by
STATUS
POWER
ON/STAND BY
Plug the supplied power cable in the wall outlet. The projec-
tor will go into its standby mode and the power indicator will
glow orange.
steady orange light
STATUS
POWER
STATUS
POWER
Turn on and off the Projector
2
steady green light
(Normal mode)
flashing green light
for one minute.
(High-Bright mode)
POWER ON/STANDBY button
INPUT
Status of indicator light: turn off
ON
ON/STAND BY
POWER
POWER ON/STANDBY button
STATUS
POW
steady green light
ER
cooling down
stand by
ON
STAND BY
/
POWER
POWER
SOURCE
Indicator
change to flashing
green light
steady orange light
R
GB
Adjust a Projected Image
3
To turn on the projector:
Select the Computer or Video Source
Only after you press the POWER (ON/STANDBY) button
on the projector cabinet or the remote control will the power
indicator turn to green and the projector become ready to use.
NOTE: To turn the projector on by plugging in the power cable, use
the menu and enable the “Auto Start” feature. (See page 37.)
NOTE: Immediately after turning on the projector, screen flicker may
occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting
is stabilized.
INPUT
N
/
N
D BY
SOURCE
P
To turn off the projector:
RD
AUTO
ADJUST
ACCESS
First press the POWER (ON/STANDBY) button on the pro-
jector cabinet or the remote control. The power indicator will
glow orange. After the projector turns off, the cooling fans
keep operating for 90 seconds.
E
N
T
E
R
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the RGB, VIDEO or S VIDEO button on the remote
control, or the Source button on the projector cabinet to se-
lect “Video” (VCR, document camera, or laser disc player),
S-Video”, “RGB” (computer or DVD with component out-
put) or “PC CardViewer” (slides on a CompactFlash card) to
display the image.
Or press the “Menu” button on the remote control or the cabi-
net and use the menu to select your video source: “Video”,
“S-Video”, “RGB” or “PC Card Viewer”.
NOTE: If no input signal is available, the projector will display an
Integra logo (factory preset).
Adjust the Image Size and the Focus
Use the Zoom ring to fine adjust the image size on the screen
Move the projector left to center the image horizontally on
the screen.
Use the Focus ring to obtain the best focus.
Rotate the rear foot to make the image square to the screen.
Place your projector on a flat level surface and Ensure
that the projector is square to the screen.
Use keystone correction for proper adjustment.
Lift the front edge of the projector to center the image ver-
tically.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the Tilt Foot
Adjust the Image Using Auto Adjust
TheAutoAdjust function automatically optimizes the image in RGB
mode.
1) Lift the front edge of the projector.
2) Press the Tilt button on the top of the projector to extend the
adjustable tilt foot (maximum height).
[Poor picture]
L E C
N
A
C
R
E
T
N
E
S E L E C T
S
S
E
T
C
C
1
S
A
U
J U
O
D
D
R
N
T
A
E
U
A
M
A
C
C
P
E
C
R
U
O
S
Y
B
D
N
A
T
/
2
1
[Normal picture]
3) Press and hold the Tilt button.
4) Lower the front of the projector to the desired height and re-
lease the button to lock the Adjustable tilt foot.
There is approximately 5 degrees of up and down adjustment
for the front of the projector. The rear foot height can be changed,
but the vertical distance from the bottom to the desk or floor
should be 0.14 ” (3.5mm) to make the projector horizontal on
the flat surface. To fine-adjust the height of the rear foot, re-
move the spacer (black rubber) and rotate the rear foot to the
desired height.
* If the projected image does not appear square to the screen
then use keystone correction for proper adjustment.
SOURCE
INPUT
L E C
N
A
C
R
E
T
T
C
E
L
N
E
E
PC
S
CARD
AUTO
ADJUST
A C C E S S
U
N
A D J U S T
A U T O
E
4
M
C A R D
P C
ACCSS
S O U R C E
E
N
T A N
S
/
T
E
R
3
C
A
N
4
P
C
C
A
R
D
Press theAuto Adjust button to adjust Position-H/V and Pixel Clock/
Phase for an optimal picture. Some signals may not be displayed
correctly or take time to switch between sources.
up
down
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume control
Basic Operation
Sound level from the speaker on the projector can be adjusted.
NOTE: When the menu or the magnifying glass appears, you cannot adjust the
volume.
Selecting the computer or video source
increase volume
Volume bar
If the projector cabined is used, each time the Source button is pressed,
the input source will change as follows:
decrease volume
→ RGB → Video → S-Video → PC Card Viewer
If no input signal is present, the input will be skipped.
Optimizing RGB image automatically
Press the Auto Adjust button to optimize an RGB image automati-
cally.
Turning off picture and sound
Press the Mute button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
Press the Auto Adjust button to fine-tune the computer image or to
remove any vertical banding that might appear and to reduce video
noise, dot interference or cross talk (this is evident when part of your
image appears to be shimmering). This function adjusts the clock
frequencies that eliminate the horizontal banding in the image. This
function also adjusts the clock phase to reduce video noise, dot inter-
ference or cross talk. (This is evident when part of your image ap-
pears to be shimmering.)
This adjustment may be necessary when you connect your computer
for the first time.
NOTE: The Auto Adjust function does not work for component signal.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Return the image to the original size.
Using Magnify button
You can use Magnify button to draw your audience's attention to the
portion of a projected image you want.
Freezing a picture
Press the Magnify button.
Press the Freeze button to freeze a picture. Press again to resume
motion.
Use the Select button to move
the magnifying glass.
Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To do so:
1. Press the Magnify button.
2. Move the magnifying glass to the area you want to enlarge.
3. Enlarge the selected area.
When the Magnify + button is pressed, you can enlarge the area
up to 400 percent.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use the L or M button to highlight your selection and press the
Enter button to place a check mark next to an option. This action
enables that feature.
Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced
motion video image is projected.
Press the Enter button again to clear the check box.
1. Press the "Menu" button on the remote control or projector cabi-
net to display the Advanced Menu or Basic/Custom Menu.
NOTE: When using a USB mouse, click the mouse button to display the
menu. For other operations, do the same way as you use your PC mouse.
2. Press the L or M button on the remote control or the projector
cabinet to highlight the menu for the item you want to adjust or
set.
3. Press the ᮣ button or the "Enter" button on the remote control or
the projector cabinet to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using ꢀ or ᮣ
button on the remote control or the projector cabinet. The on-screen
slide bar will show you the amount of increase or decrease.
If you select an item with a solid triangle ᮣ and press the Enter
button on the remote control or the projector cabinet, you can en-
able all the items within that submenu.
Also you can turn on an item within the submenu without placing
a check mark on the main menu item.
5. Changes are stored until you adjust it again.
ENTER ...... Stores the setting or adjustments.
CANCEL ... Return to the previous screen without storing settings
or adjustments.
NOTE: Up to 12 main menu items (within Basic/Custom Menu Edit, not
including submenu items) can be selected.
6. Repeat steps 2-5 to adjust an additional item, or press "Cancel" on
the projector cabinet or the remote control to quit the menu dis-
play.
3. In order for the changes to take effect, use the ꢀ or ᮣ button on
the remote control or the projector cabinet to highlight “OK”, then
press the Enter button. To cancel the changes, use the L or M
button to highlight “Cancel” and press the “Enter” button. To re-
turn to the factory default, select “Reset” then press the “Enter”
button.
Customizing Basic/Custom Menu
The Basic/Custom menu can be customized to meet your require-
ments. Selecting a menu item from the “Basic/Custom Menu Edit”
list, allows you to custom tailor the menu items to your needs.
The default Basic/Custom Menu items are:
Source Select (RGB, Video, S-Video and PC Card Viewer), Picture, Volume, Image
Options (Keystone), Projector Options (Menu and Setup) and Tools (Capture, PC Card
Files and ChalkBoard).
1. Select “Basic/Custom Menu Edit” to display the “Basic/Custom
Menu Edit” screen.
NOTE: Once you have selected OK on the Basic/Custom Menu Edit screen,
you cannot cancel the changes on the Menu screen. However, you can re-edit
the menu items over again as described in the steps above.
NOTE: If the “Advanced Menu” item has been selected on the Menu mode, you get
the “Confirmation Change Menu” upon completion of “Basic/Custom Menu” ed-
iting. In this case, selecting “Yes” then “Enter” will close all the menus and apply
the changes from the Advanced menu to the Basic/Custom Menu.
If you select “No” then “Enter” functions, then all menu items will return to the
Advanced menu, but your changes will still be available within the “Basic/
Custom Menu” selection. To display the previously tailored Basic/Custom
Menu, select “Basic/Custom Menu” from the “Menu Mode”.
An item “To Advanced Menu” will be
added to the bottom of the Basic/Custom
Menu.
Selecting this item and pressing the “En-
ter” button will display the “Advanced
Menu” features.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a USB Mouse
Using a USB mouse gives you a smooth operation. A commercially
available USB mouse is required.
NOTE:There may be some brands of USB mouse that the projector does not
support.
Operate the Menus using the USB mouse
Mouse Cursor
When connecting a USB mouse to the projector, you get a mouse
cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse
cursor disappears.
Menu Display
Clicking with a mouse button displays the menu.
Clicking
displays the pull-down menu.
To close the menu, click anywhere in the background.
Adjusting and Setting Display
You can select a menu item and click with a mouse button to
make adjustments and setting.
Examples
Click (or press and hold) the mouse button ꢀ or ᮣ to adjust the
brightness.
Or click and drag the mouse button on the slide bar horizontally
to adjust it.
To save the adjustments, click . The display is closed.
If you click anywhere in the background while displaying adjust-
ment and setting menu or dialog box, you will get the main menu
at the clicking point.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Tree
Advanced Menu
Source Select
Picture
RGB
Video
Volume
Image Options
Color Management
S-Video
PC Card Viewer
Brightness/Contrast/Color/Hue/Sharpness
Volume
Projector Options
Tools
Keystone
High-Bright/Normal
Information
Lamp Mode
Advanced Options
Factory Default
Aspect Ratio
Noise Reduction
Position/Clock
Resolution
Normal/Zoom/Wide Zoom/Cinema
Off/Low/Medium/High
Horizontal/Vertical/Clock/Phase
Auto/Native
Video Filter
On / Off
All Data/Current Signal
Gamma Correction
Color Matrix
Normal/Natural 1/Natural 2
Select Color Matrix HDTV/SDTV
Select Color Matrix Type B-Y/R-Y,Cb/Cr,Pb/Pr
Brightness R/G/B, Contrast R/G/B
White Balance
Menu
Setup
Menu Mode(Advanced Menu, Basic/Custom Menu)
Basic/Custom Menu Edit
Page 1
Page 2
Language (English/German/French/Italian/Spanish/Swedish/Japanese)
Projector Pointer (Pointer 1-8)
Menu Display Time (Manual/Auto 5 sec/Auto 15 sec/Auto 45 sec)
Message Source Display (On/Off)
No input (On/Off)
Direct Button Volume Bar (On/Off)
Keystone Bar (On/Off)
Page 1 Orientation (Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front)
Cinema Position (Top/Center/Bottom)
Background (Blue/Black/Logo)
Mouse Button(Right Hand/Left Hand)
Sensitivity(Fast/Medium/Slow)
Page 2 PC Card Viewer Options Show Folder List
(Auto Play/Manual Play)
Interval (5-300 sec)
Capture Options (High Quality/Normal/High Compression)
Page 3 Signal Select RGB (Auto/RGB/Component)
Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)
S-Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)
Page 4 Auto Adjust (RGB Only)
Auto Start
Power Management
Power Off Confirmation
Keystone Save
White Segment
Clear Lamp Hour Meter
Page 5 Communication Speed(4800/9600/19200/38400)
Default Source Select(Last/Auto/Select)
(RGB/Video/S-Video/PC Card Viewer)
Control Panel Key Lock (Enable/Disable)
Capture
PC Card Files
ChalkBoard
Page1
Page2
Page3
Page4
Source Name/Input Terminal/Horizontal Frequency/Vertical Frequency/Sync Polarity
Signal Type/Video Type/Sync Type/Interlace/Resolution
Aspect Ratio/Gamma Correction/Noise Reduction/Color Matrix/Matrix Type
Remaining Lamp Time/Lamp Hour Meter/Projector Usage
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Elements
Tab
Title bar
Highlight
Close Button
Radio Button
OK Button
Cancel Button
Solid triangle
Check box
Grip icon
Tool bar
Slide bar
Menu windows or dialog boxes typically have the following elements:
Title bar:
Indicates the menu title.
Highlight:
Solid triangle:
Tab:
Indicates the selected menu or item.
Indicates further choices are available. A highlighted triangle indicates the item is active.
Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Use this round button to select an option in a dialog box.
Radio button:
Check box:
Slide bar:
Place a checkmark in the square box to turn the option On.
Indicates settings or the direction of adjustment.
OK button:
Cancel button:
Close button:
Toolbar:
Press to confirm your setting. You will return to the previous menu.
Press to cancel your setting. You will return to the previous menu.
Click to close the window with saving changes. (USB mouse only)
Contains several icons for specific tasks. It is also referred to as "launcher".
Point the mouse here, and click and drag to move a toolbar.
Grip icon:
30
Download from Www.Somanuals.com. All Manuals Search And Download.
The launcher is a tool bar including the following buttons:
Drag ........... Drags to move the tool bar. (for USB mouse operation only)
Prev ............ Returns to the previous slide or folder.
Menu Descriptions & Functions
Source Select
Next ............ Advances to the next slide or folder.
Play ............ Plays back automatically or manually depending on the setting on
PC Card Viewer Options of the menu. This allows you to move on
to the next slide when "Manual Play" is selected.
Stop ............ Stops Auto Play while you are playing back and to resume playing
from the selected slide or folder when "Auto Play" is selected.
Jump .......... Displays a list of slides while you are playing back.
Select ......... Displays a list of folders while you are playing back.
Setup .......... Displays the PC Card Viewer Options dialog box on Page 2 of the
Setup dialog box.
Delete ......... Deletes a captured slide(s) or all the captured slides in the se-
lected folder.
View ........... Hides the tool bar while you are playing back. Clicking with the
right button of a mouse shows it again.
Enables you to select a video source such as a VCR, DVD player, laser
disc player, computer or document camera depending on what is con-
nected to your inputs.
Press the "Select" button on the projector cabinet or LM buttons on your
remote control to highlight the menu for the item you want to adjust.
Picture (not available for PC Card Viewer)
RGB
Selects the computer connected to your RGB or component signal.
Video
Selects what is connected to yourVideo input-VCR, laser disc player,
DVD player or document camera.
S-Video
Selects what is connected to your S-Video input-VCR, DVD player,
or laser disc player.
NOTE: A frame may freeze for a brief period of time when a video is played
back in fast-forward or fast-rewind with a Video or S-Video source.
Provides access to controls for your image. Use the "Select" button
on the projector cabinet or ꢀ ᮣ buttons on the remote control to
highlight the menu for the item you want to adjust.
PC Card Viewer
This feature enables you to make presentations using a CompactFlash
card that contains captured images.
Brightness .. Adjusts the brightness level or the back raster intensity.
Contrast ...... Adjusts the intensity of the image according to the incoming sig-
nal.
Color .......... Increases or decreases the color saturation level (not valid for RGB).
Hue ............. Varies the color level from +/- green to +/-blue. The red level is
used as reference. This adjustment is only valid for Video and
Component inputs (not valid for RGB).
NOTE: Even if you switch the current PC Card Viewer source to another source,
the current slide is retained. When you return back to the PC Card Viewer, you
will get the slide that has been retained.
A launcher will appear when you press the MENU button.
Sharpness .. Controls the detail of the image for Video (Not valid for RGB and
Component).
Volume (not available for PC Card Viewer)
Adjusts the sound level of the projector.
NOTE: You can also display the volume bar without opening the menu. See
"Volume Bar (Direct Button)"on page 35 for more details.
View
Setup
Prev
Play
Jump
Drag
Select
Delete
Next
Stop
A press of the MENU button displays the toolbar; a press of the MENU
button again displays the Menu and hereafter each press of the MENU
button switches displaying between the Menu and the toolbar.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Options
Aspect Ratio (not available for RGB and PC Card Viewer)
Aspect Ratio allows you to select the best Aspect mode to display
your source image.
When 4:3 is selected from the source (i.e. DVD player), the follow-
ing selections will display:
Normal
Zoom
Wide Zoom
Cinema
Keystone
Standard
4:3 Aspect
All 4 sides stretched
Left and right
stretched
Left & Right
stretched
This feature corrects the keystone (trapezoidal) distortion to make
the top of the screen longer or shorter to be the same as the bottom.
Use the ꢀ or ᮣ buttons on the slide bar to correct the keystone
(trapezoidal) distortion.
When 16:9 is selected from the source (i.e. DVD player),
the following selections will display:
Normal
Zoom
Wide Zoom
Cinema
All 4 sides stretched
Left & right stretched
Left and right
stretched to display
the true aspect
16:9 image displayed
in 4:3 mode
Normal
Keystone distortion
NOTE: You can select three image positions for Cinema: Top, center,
and bottom.
See page 35 for setting image positions.
NOTE: The keystone angle can be corrected between 30 degrees upward and
30 degrees downward at a 0 degree-projection angle.
Depending on the type of graphics being used, the picture may get
blurred or keystone correction may not be possible when excessive
keystone correction is used.
The idea is, the closer you are to native resolution, the better image
you will see.
Lamp Mode
This feature enables you to select two the brightness modes of the
lamp: High-Bright and Normal modes. The lamp life can be extended
up to 1500 hours by using the Normal mode.
Normal Mode ..............This is the default setting.
High-Bright Mode .......Select this mode to make the image brighten than
in Normal mode.
NOTE: If you have selected the Normal mode, the lamp lights in High-Bright
mode for one minute after the projector is turned on. After one minute the
lamp will change to Normal mode.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Noise Reduction (not available for RGB and PC Card Viewer)
Resolution (when Auto Adjust is off)
You can select three levels video noise reduction.
NOTE: The lower the Noise Reduction level, the better the image quality by
way of higher video bandwidth.
This allows you to activate or deactivate the Advanced AccuBlend
feature.
Auto ............ Turns on the Advanced AccuBlend feature. The projector auto-
matically reduces or enlarges the current image to fit the full screen.
Native ......... Turns off the Advanced AccuBlend feature. The projector displays
the current image in its true resolution.
Position/ Clock (when Auto Adjust is off)
See “Auto Adjust (RGB Only)” on page 36 for turning on or off the
Auto Adjust feature.
NOTE: While you are displaying an image with higher resolution than the
projector's native resolution, even when you are in the Native mode, the image
is displayed full screen using the Advanced AccuBlend feature.
Video Filter (when Auto Adjust is off)
This allows you to manually adjust the image horizontally and verti-
cally, and adjust Clock and Phase.
This function reduces video noise.
Horizontal/Vertical Position:
On ................ The low-pass filter is applied.
Off ................ The filter is removed.
ꢀ
Adjusts the image location horizontally and vertically using the
ᮣ
and buttons.
Screen adjustments are possible even when the filter is On.
This adjustment is made automatically when the Auto Adjust is
turned on. See “Auto Adjust (RGB Only)” on page 36 for turning
on or off the Auto Adjust feature.
Factory Default
Clock .......... Use this item to fine tune the computer image or to remove any
vertical banding that might appear. This function adjusts the clock
frequencies that eliminate the horizontal banding in the image.
Press the ꢀ and ᮣ buttons until the banding disappears.
This adjustment may be necessary when you connect your com-
puter for the first time. This adjustment is made automatically when
the Auto Adjust is turned on.
Changes all adjustments and setting to the factory preset.
All Data ....... Reset all the adjustments and settings for all the signals to the
factory preset.
Phase ......... Use this item to adjust the clock phase or to reduce video noise,
dot interference or cross talk. (This is evident when part of your
image appears to be shimmering.) Use the ꢀ and ᮣ buttons to
adjust the image.
The items can be reset except Language, Communication Speed,
Remaining Lamp Time, Lamp Hour Meter and Projector Usage.
(To reset the lamp usage time, see “Clear Lamp Hour Meter” on
page 37.)
Use "Phase" only after the "Clock" is complete.
This adjustment is made automatically when the Auto Adjust is
turned on.
Current Signal . Resets the adjustments for the current signal to the factory preset
levels.
The items that can be reset for the currently projected image are:
Picture (Brightness, Contrast, Color, Hue and Sharpness), Image
Options (Aspect Ratio, Noise Reduction, Position/Clock, Resolu-
tion and Video Filter) and Color Management (Gamma Correc-
tion, Color Matrix and White Balance).
NOTE: The Volume, Keystone and all the items in the Projector Options can be
reset only when "All Data" is selected.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Management
Projector Options
Gamma Correction (not available for PC Card Viewer)
Use the ꢀ or ᮣ button to choose "Normal" when in a lighted room
and "Natural 1&2" when in a darkened room. "Natural 1" for better
flesh tone; "Natural 2" for true reproduction of middle tones.
Each mode is recommended for :
Normal ....... For the regular picture
Natural 1 ..... For true color reproduction of natural tones
Natural 2 ..... For dark portions of a picture
Menu
Color Matrix (available for component video signal only)
First select an appropriate color matrix to fit your component signal
for HDTV or SDTV. Then select an appropriate matrix type from B-
Y/R-Y, Cb/Cr or Pb/Pr.
White Balance (not available for PC Card Viewer)
Allows you to set preferences for the on-screen menu.
Press “OK” to save your changes for all the features of Page 1 and
Page 2.
[Page1]
Menu Mode:
This feature allows you to select two menu modes: Advanced Menu
and Basic/Custom Menu.
Advanced Menu ........ This is the menu that contains all the available menus
and commands.
Basic/Custom Menu . This is the menu that you can customize using the Basic/
Custom Menu Edit to fit your needs.
The factory default Basic/Custom menu includes:
Source Select (RGB, Video, S-Video and PC Card Viewer), Picture, Volume,
Image Options (Keystone), Projector Options (Menu and Setup) and Tools (Cap-
ture, PC Card Files and ChalkBoad).
This allows you to adjust the white balance. Brightness for each color
(RGB)is used to adjust the black level of the screen;
Contrast for each color (RGB)to adjust the white level of the screen.
First use the L or M buttons to select R, G, or B for the brightness
and the contrast. Next use the ꢀ or ᮣ buttons to adjust the level.
See page 27 for instructions about how to customize the Basic/Custom Menu.
Language:
You can choose one of seven languages for on-screen instructions.
The options are: English, German, French, Italian, Spanish, Swedish
and Japanese.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Pointer:
Direct Button:
This option is not available on this model.
Volume Bar:
This option turns on or off the volume bar when you adjust the sound
volume using VOLUME +/- (up and down) button.
On .............. You can increase or decrease the sound volume with the volume
bar on screen.
Off .............. You can increase or decrease the sound volume without having to
use the volume bar.
Menu Display Time :
This option allows you to select how long the projector waits after
the last touch of a button to turn off the menu.
The preset choices are "Manual", "Auto 5 sec", "Auto 15 sec", and
"Auto 45 sec". The "Auto 45 sec" is the factory preset.
Manual ....... The menu can be turned off manually.
Auto 5 sec .. The menu will automatically be turned off in 5 seconds if no but-
tons are pressed within 5 seconds.
Keystone Bar:
This option is not available on this model.
Auto 15 sec ... The menu will automatically be turned off in 15 seconds if no
buttons are pressed within 15 seconds.
Auto 45 sec ... The menu will automatically be turned off in 45 seconds if no
buttons are pressed within 45 seconds.
Setup
Enables you to set operating options.
Press "OK" to save your changes for all the features of Page 1, Page
2, Page 3, Page 4 and Page 5.
[Page1]
[Page2]
Orientation:
This reorients your image for your type of projection.
The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
Message:
You can choose the desired information to be displayed on the screen.
On .............. The message will be displayed.
Off .............. The message will not be displayed.
Cinema Position:
This feature selects the vertical position of the image when viewing
video with Cinema aspect ratio selected.
Source Display: You can turn on and off the information for input
name such as VIDEO and RGB.
When Cinema aspect ratio is selected on earlier models, the image is
displayed with black borders on the top and bottom.
You can select the vertical position among three options:
Top ............. Image position is at the top with a black border on bottom.
Center ......... Image position is at the center with black borders on top and bot-
tom.
When this option is on, the current input will be displayed each time
you switch sources or turn on the projector.
No Input: This option turns on or off the "No Input" message to be
displayed in the top right corner on the screen.
Bottom ........ Image position is at the bottom with a black border on top.
Background:
Use this feature to display a blue/ black screen or logo when no sig-
nal is available. The default background is Integra. You can change
the logo screen using the PC Card Files feature. See page 38.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Mouse Settings:
[Page 3]
This option lets you to change your USB mouse settings. The mouse
settings feature is available for USB mouse only. Choose the settings
you want:
Signal Select
Mouse Button ........... "Right Hand" or "Left Hand"
Mouse Sensitivity ..... "Fast", "Medium" or "Slow"
[Page 2]
RGB:
Allows you to choose "RGB" for an RGB source such as a computer,
or "Component" for a component video source such as a
DVD player. Normally select "Auto" and the projector automatically
detects a component signal. However there may be some component
signals that the projector is unable to detect. If this is the case, select
"Component".
PC Card Viewer Options
Show Folder List:
VIDEO and S-VIDEO:
This feature enables you to select composite video standards manu-
ally. Normally select "Auto".
Select the video standard from the pull-down menu.
This must be done for Video and S-Video separately.
If this option is checked, when PC Card Viewer input is selected on
the projector, the folder lists will be displayed and allows you to se-
lect the presentation from a CompactFlash card.
Auto Play:
If this option is checked, any given slide will start to play automati-
cally.
[Page 4]
Auto Play Interval:
You can specify interval time between 5 and 300 seconds.
NOTE: The Auto Play Interval time set on the PC Card Viewer Utility overrides
the one set here.
Manual Play:
Views a slide manually when PC Card Viewer input is selected.
NOTE: The Auto Play and Manual Play options determine the behavior of the
Play/Stop [
/
] icon on the Viewer toolbar.
NOTE: If you check "Auto Play" and select "PC Card Viewer" on the projector,
the slides will automatically start to play back from any given slide.
Capture Options: (available for JPEG only)
Auto Adjust (RGB Only):
These options are used for the Capture function that you can select
from Tools. You have three options for JPEG compression quality:
High quality, Normal and High Compression.
When "Auto Adjust" is set to "On", the projector automatically de-
termines the best resolution for the current RGB input signal to project
an image using the Advanced AccuBlend Intelligent Pixel Blending
Technology.
The image can be automatically adjusted for position and stability;
"Horizontal Position", "Vertical Position", "Clock", "Phase", and
"Resolution."
High Quality .....................Gives quality of JPEG a priority.
Normal .............................Gives normal JPEG quality.
High Compression ........... Gives compression a priority.
On .............. Automatically adjusts image "Horizontal Position", "Vertical Po-
sition", "Clock", "Phase" and "Resolution".
Off .............. User can adjust the image display functions ("Horizontal Posi-
tion", "Vertical Position", "Clock", "Phase" and "Resolution") manu-
ally.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Start:
[Page 5]
Turns the projector on automatically when the power cable is inserted
into an active power outlet. This eliminates the need to always use
the "Power" button on the projector cabinet or remote control.
Power Management:
When this option is on and there is no RGB input for five minutes or
more, the projector will automatically turn itself off.
Power Off Confirmation:
This option determines whether a confirmation dialog for turning off
the projector will appear or not.
Keystone Save:
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved
when you turn off the projector.
Communication Speed:
White Segment:
This feature sets the baud rate of the PC Control port (Mini DIN 8
Pin).
It supports data rates from 4800 to 38400 bps.
The default is 38400 bps. Select the appropriate baud rate for your
equipment to be connected.
You can put emphasis on either brightness or color for a projected
image.
If you prefer putting emphasis on brightness, place a checkmark in
the box to turn the option on. If you prefer an image in truer color,
turn off this option.
Default Source Select:
Clear Lamp Hour Meter:
You can set the projector to default to any one of its inputs each time
the projector is turned on.
Last ............ Sets the projector to default to the previous or last active input
each time the projector is turned on.
Auto ............ Searches for an active source in order of RGB → Video → S-
Video → PC Card Viewer → RGB and displays the first found
source.
Resets the lamp clock back to zero. Pressing this button appears a
confirmation dialog box. To reset the lamp usage hour, press "OK".
NOTE: The projector will turn off and go into standby mode after 1100 hours
(up to 1600 hours in Normal mode) of service. If this happens, press the
"Lamp Reset" button on the remote control for ten seconds to reset the lamp
clock back to zero. Do this only after replacing the lamp.
Select ......... Displays the selected source input every time the projector is started
up. Select an input from the pull-down menu.
Control Panel Key Lock:
This option turns on or off the Control Panel Key Lock function.
NOTE:
* This Control Panel Key Lock does not affect the remote control and the PC
Control functions.
* When the cabinet buttons are disabled, pressing and holding the CANCEL
button for about 10 seconds will change the setting to enabled.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Card Files:
Tools
Displays a list of all the files stored in the CompactFlash card so that
you can select a file you want to display.You can also sort files by file
name or date, or display the file.
Although a list of all the files in the CompactFlash card is displayed,
you can view files in idx, text, HTML, JPEG and BMP format only.
Selecting BMP and JPEG files automatically switches to the PC Card
Viewer source.
NOTE: When an image with a resolution of XGA(1024
ן 768) or higher is projected, the PC Card Files screen may not be correctly displayed.
Provides tools for capturing images, displaying files in a
CompactFlash Card and drawing.
NOTE: The "Capture" and "PC Card Files" features are required for a
CompactFlash card.
Capture:
Allows you to capture an image from a source that is currently being
displayed. The image is saved as JPEG in the CompactFlash card.
When you select Capture from the menu, you will get a tool bar.You
can capture an image directly using the tool bar when the menu is not
displayed.
Selecting "Execute" displays the file you selected.
When you select a JPEG or BMP file and press the Enter button on
the remote control or the cabinet, or “Execute” on the above, you will
get a toolbar. This toolbar is used to return to the PC Card Files screen.
Capture Exit
Drag
Return
Freeze
Close
Drag
The tool bar includes the following buttons:
Drag ........... Drags to move the tool bar. (for USB mouse operation only)
Capture ....... Captures an image and save it as a JPEG file in a CompactFlash
card.
Drag ........... Drags to move the tool bar. (for USB mouse operation only)
Return ......... Returns to the PC Card Files screen.
Close .......... Close the toolbar.
Freeze ......... Freezes and unfreezes images.
Exit ............. Exits the Capture function.
Changing Background Logo
The Logo button allows you to select a background logo from graphic files
on a CompactFlash card and change to it as the background logo.
Unless a CompactFlash card is inserted into the PC Card slot of the
projector, the Capture feature is not available.
NOTE: File size must be 64KB or less. Other file formats than JPEG and BMP
are not available.
The "Card Error" display means that the free space of the
CompactFlash card is insufficient for saving images. Make more space
available on the card by erasing unwanted images with your PC. The
number of images that can be captured depends on the size of the
CompactFlash card.
1. Use the L or M button to select a JPEG or BMP file for your
background logo.
NOTE: Be sure not to turn off the power or remove the CompactFlash card
while capturing an image. Doing so could cause a loss of the data in the
CompactFlash card or damage to the card itself.
NOTE: Captured images with higher resolution than the projector's native reso-
lution cannot be displayed correctly.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use the ᮣ button and then M button to select “Logo”.
3. Press the Enter on the remote control or the cabinet. You will get
the confirmation dialog box.
Information
4. Select “OK” and press the Enter button. This completes changing
a logo for the background.
* Once you have changed the background from the Integra logo to
another, you cannot return the logo to background even by using
Factory Default. To do so, repeat the above steps.
ChalkBoard: (available only when using with USB mouse)
Provides the tool bar for producing freehand drawings.
Displays the status of the current signal, and the lamp and the projec-
tor usage hours.
This dialog box has four pages.
Pen
Eraser
View
Drag
Exit
The information included are as follows:
Clear
Color
[Page 1]
[Page 2]
Source Name
Input Terminal
Horizontal Frequency
Vertical Frequency
Sync Polarity
Signal Type
Video Type
Sync Type
Interlace
Drag ........... Drags to move the tool bar. (for USB mouse operation only)
Pen ............. Left-click and drag to draw. Left-click [ L ] or right-click the pen
icon to display the pen palette containing four lines of different
thickness from which you can select a line you prefer by left-click-
ing.
Color .......... Selects a color. Left-click to display the color palette from which
you can select a color you prefer by left-clicking.
Eraser ......... Left-click and drag to erase part of a drawing. Left-click [L ] or
right-click the eraser icon to display the eraser palette containing
four eraser of different thickness from which you can select an
eraser you prefer by left-clicking.
Resolution
[Page 3]
[Page 4]
Aspect Ratio
Gamma Correction
Noise Reduction
Color Matrix
Remaining Lamp Time (%)
Lamp Hour Meter (H)
Projector Usage (H)
Matrix Type
Clear ........... Left-click to clear the drawing completely from the ChalkBoard
screen.
View ........... Hides the tool bar by left-clicking. Right-clicking anywhere on the
screen displays the ChalkBoard tool bar again.
NOTE:The progress indicator shows the percentage of remaining bulb life.
The value informs you of the amount of lamp and projector usage respectively.
Remaining Lamp Time Display:
Exit ............. Clears the complete drawing and exits the ChalkBoard.
When the remaining lamp time reaches 0, the Remaining Lamp Time
bar indicator changes from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not
turn on regardless of whether the lamp mode is set to Normal or High-
Bright.
NOTE:
* The ChalkBoard feature is available only when a USB mouse is used. Free-
hand drawings cannot be saved or captured.
* The menu is not available while you display the ChalkBoard screen.
* The Capture and the Source Display function are not available on ChalkBoard
screen.
* Switching slides clears a drawing completely.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the CompactFlash Card
• Hold the CompactFlash card horizontally and insert it slowly
into card slot with its top facing up.
• The eject button pops out once the CompactFlash card is fully
inserted.
Using the PC Card Viewer function
Features
The Viewer feature allows slides stored on a CompactFlash memory
card (referred to as CompactFlash card in this manual) to be dis-
played on the projector. Even if no computer is available, presenta-
tions can be conducted simply with the projector. This feature is
convenient for holding presentations at meetings and in offices, as
well as for playing images taken on digital cameras.
Check that the CompactFlash card is fully inserted.
NOTE: Do not try to force the CompactFlash card into the slot.
O
P
C
C
O
C
N
A
T
N
C
R
EL
O
L
V
ID
E
O
U
S
P
B
C
C
A
R
D
Easy to use
• Presentations can be started immediately simply by inserting a
CompactFlash card (not supplied)
• Easy slide switching
AC IN
• Remote control operation
• Jumping to list of slides or any specific slide
High quality images
• High resolution up to 1024
ן 768 dots • 24-bit full color playback
• Viewing of digital camera images
Ejecting the CompactFlash Card
Press the eject button. The CompactFlash card pops out a little. Grasp
the edges of the CompactFlash card and pull it out. Do not eject the
CompactFlash card while its data is being accessed.
Inserting and Ejecting a CompactFlash Card
Eject button
R
O
L
V
A CompactFlash card is used to view presentation data prepared on
the computer and to capture and play images projected with the pro-
jector.
ID
E
O
U
S
B
A
R
D
AC IN
Install the CompactFlash card on a PC card adapter when using on
your PC.
• Set the CompactFlash card in the direction shown in the dia-
gram and insert it into the card adapter.
Card adapter (not supplied)
PC-Card
Adapter
CompactFlash card
(not supplied)
8MB
Direction for Inserting the CompactFlash Card
The CompactFlash card has a top and bottom and must be in-
serted into the PC card slot in a specific direction. It cannot be
inserted backwards or upside-down. Attempting to force it into
the slot in the wrong direction may break the internal pin and
damage the card slot. Refer to the CompactFlash card's operat-
ing instructions for the proper direction of insertion.
CompactFlash Card Type
The PC Card slot accepts CompactFlash only.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Drag: Drags to move the tool bar. This is available for USB
mouse operation only.
Operating the PC Card Viewer Function from
the Projector (playback)
Prev:
Next:
Play:
Returns to the previous slide or folder. Or this lets
you play slides back in reverse.
This section describes the operation for showing slides of presenta-
tion documents created using the PC Card Viewer function with the
projector.
It is also possible to make slides directly from the images projected
with the projector.
Advances to the next slide or folder. Or this lets you
play slides back.
Plays back automatically or manually depending on
the setting on PC Card Viewer Options of the menu.
This allows you to move on to the next slide when
“Manual Play” is selected.
Projecting slides
1. Insert a CompactFlash card into the card slot.
Insert the CompactFlash card with the side with the insertion di-
rection arrow on the top.
Stop:
This allows you to stopAuto Play while you are play-
ing back and to resume playing from the selected slide
or folder when “Auto Play” is selected.
* Press the eject button to eject the card.
Jump: Displays a list of slides while you are playing back.
Select: Displays a list of folders while you are playing back.
2. Select the “PC Card Viewer” from the Source Select menu.
Setup: Displays the PC Card Viewer Options dialog box on
Page 2 of the Setup dialog box.
Delete: Deletes a captured slide(s) or all the captured slides
in the Capture – specific folder.
View: Hides the tool bar while you are playing back. Press-
ing the MENU button or clicking with the right but-
ton of a mouse shows it again.
3. Project slides.
NOTE: If no memory card is inserted in the PC CARD slot, there is no signal,
and a black, blue or logo background is displayed, depending on the setting.
Checking “Show Folder List”, means that selecting PC Card
Viewer input displays a list of the folders in the CompactFlash
card and if “Auto Play” is checked the projector automatically
starts to play slides at the first slide of the folder you have se-
lected.
Playback is stopped when ꢀ or ᮣ on the remote control or the cabi-
net is pressed in Auto Play mode.
A tool bar will appear when you press the MENU button on the re-
mote control or the projector cabinet or clicking with the right button
of a mouse.
View
Setup
Prev
Play
Jump
Drag
Select
Delete
Next
Stop
The tool bar includes the following buttons:
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Captured Images
Capturing Images Displayed on the Projector
View
Setup
Prev
Play
Jump
Storing images displayed on the projector on the
CompactFlash card
Drag
Preparations:
Insert the CompactFlash card into the card slot.
Insert the CompactFlash card with the side with the insertion
direction arrow on the top.
Select
Delete
Next
Stop
Using the Delete button on the tool bar for PC Card Viewer can de-
lete captured images.
* Press the eject button to eject the card.
To delete captured images:
1) Select PC Card Viewer.
2) Use ᮣ button to select the Capture folder in the right bottom of
the screen.
1. Project the image you wish to store on the projector.
2. Select the “Capture” from the Tools menu.
3) Press the MENU button to display the tool bar.
4) Use the ꢀ or ᮣ button to select the Delete icon and press the
ENTER button or click with a mouse button.
Viewing Digital Images
Freeze
Digital images can be played with the PC Card Viewer if the follow-
ing conditions are met:
Drag
• If the image can be stored on an MS-DOS format CompactFlash
card
• If the image can be stored in a format supported by the PC Card
Viewer.
Capture
Exit
3. A tool bar will appear.
With the PC Card Viewer, images on the card are searched for in
directories and images in JPEG or BMP format are recognized
as slides.
The tool bar includes the following buttons:
Searchable directories are directories within two steps from the
root directory, and searchable images are images within the first
12 files in the directory. Only file and slide switching are pos-
sible.
Drag: Drags to move the tool bar (for USB mouse operation
only).
Capture:Captures an image and save it as a JPEG file in a
CompactFlash card.
NOTE: The maximum number of images recognized as slides within one di-
rectory is 128.
Freeze: Freezes and unfreezes images.
Exit: Exits the Capture function. Another option to exit the
Capture function is to press MENU or CANCEL but-
ton on the remote control or projector cabinet.
NOTE: You can compress a captured file (JPEG) using the Capture Options in
the Setup dialog. See page 36.
NOTE: Captured images with higher resolution than the projector's native reso-
lution cannot be displayed correctly.
NOTE:
• File size of the captured image varies depending on the resolution of an
input signal.
• Since an image data is compressed with the JPEG format, the image is
slightly degraded.
NOTE: An hourglass indicating that an image is being captured appears on the
projector's display. Do not eject the CompactFlash card or turn off the
projector's power while this icon is displayed. Doing so will damage the
CompactFlash card data.
If the CompactFlash card data is damaged, use a computer to repair the data.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminology
PC card
This is the name of a card currently being standardized by the Japan Electronic Industry Association (JEIDA) and
PCMCIA (Personal Computer Memory Card Interface Association) of the United States.
ATA card
A type of PC card. ATA was originally a type of interface between computers and fixed disk devices. The ATA card
is a standard card-type recording medium.
CompactFlash
TYPE (I, II and III)
BMP
CompactFlash card is a small removable card conforming to ATA specifications. It is one-fourth the volume of a
PCMCIA card.
PCMCIA 2.1 PC cards are divided into three types according to their thickness: Type I (3.3 mm), Type II (5.0 mm)
and Type III (10.5 mm).
A type of image format. The standard Windows Bit Map format used for MS-DOS/Windows-compatible comput-
ers.
JPEG
A type of image format. "JPEG" is the abbreviation of Joint Photographic Experts Group. JPEG compression offers
efficient data storage. The data not required for displaying the image is identified and deleted. Since the data is
deleted, JPEG algorithms are said to be irreversible. This means that once the image is compressed, the decom-
pressed image it is not the same as the original image.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp.
3 Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical
shock. Do not attempt to circumvent this interlock.
Replacing the Lamp
After your lamp has been operating for 1500 hours (1000 hours in
High-Bright mode) or longer, the “Status” light in the cabinet will go
on and the message will appear. Even though the lamp may still be
working, replace it at 1500 hours (1000 hours in High-Bright mode)
to maintain optimal projector performance.
A U D I O
P C C O N T
R O L
R G
CAUTION
Interlock
4 Insert a new lamp housing until the lamp housing is plugged into
the socket.
CAUTION: Do not use a lamp other than the Integra replacement lamp.
Order this from your Integra dealer.
• DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait 90
seconds, and then disconnect the power cable. Allow at least
one hour for the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
•
The projector will turn off and go into stand by mode after 1600
hours (1100 hours in High-Bright mode) of service. If this hap-
pens, be sure to replace the lamp. If you continue to use the lamp
after 1500 hours (1000 hours in High-Bright mode) of use, the
lamp bulb may shatter, and pieces of glass may be scattered in
the lamp case. Do not touch them as the pieces of glass may cause
injury. If this happens, contact your Integra dealer for lamp re-
placement.
A U D I O
P C C O N T R
O L
R G B
5 Secure it in place with the three screws.
Be sure to tighten the screws.
To replace the lamp:
1 Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
A
U
D
I O
P
C
C
O
N
T
R
O
R
G
L
B
S
- V
I D
E
O
6 Reattach the lamp cover.
A
U
D
I O
P
C
C
O
N
T
R
O
R
G
L
B
S
- V
I D
E
O
V
I
D
U
E
S
O
B
P
C
C
A
R
D
A C I N
A
U
D
I O
P
C
C
O
N
T
R
O
R
G
L
B
S
- V
I D
E
O
7 Tighten the lamp cover screw.
Be sure to tighten the screw.
2 Loosen the three screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The three screws are
not removable.
A U D I O
P C C O N T R
R G B
O L
A
U
D
8 After you install a new lamp, select the Main menu → [Projector
Options] → [Setup] → [Page 4] → [Clear Lamp Hour Meter] to
reset the lamp usage hours.
I O
P
C
C
O
N
T
R
O
R
G
L
B
S
- V
I D
E
O
V
I D
U
E
S
O
B
P
C
C
A
R
If the projector will not be turned on after using 1600 hours (1100
hours in High-Bright mode) of service, press and hold the “Lamp
Reset” button on the remote control for ten seconds or longer to
reset the lamp time clock to zero.
D
A C I N
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5. TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector.
Power/Status Light Messages
Power Indicator
Condition
Status Indicator
Note
Standby
Steady orange
–
–
Cooling down
Blinking green
Steady green
Steady green
Steady green
–
Blinks green for 90 seconds
Lamp in Normal mode
Lamp in High-Bright mode
Retrying to turn on lamp
–
–
–
Steady green
Blinking orange
The projector retries 3 times at an interval of 15
sec for max. 45 sec)
One minute after lamp is turned on Blinking green
No light in Normal mode / Steady green
in High-Bright mode
–
Lamp has reached its end of life
(High-Bright: 1000 hours or over)
(Normal: 1500 hours or over)
Steady green
Steady red
Message appears on screen during 1500-1600
hours (1000-1100 hours: High-Bright mode) of
lamp usage. The projector reaches its end of life.
Please replace the lamp as soon as possible
Lamp life has reached its end of Steady orange
life
Steady red
The projector is in standby mode and cannot be
turned on.
(High-Bright: 1100 hours or over)
(Normal: 1600 hours or over)
Lamp cover error
Temperature error
Fan error
Steady orange
Steady orange
Steady orange
Steady orange
Blinking red (1 sec interval)
Blinking red (4 sec interval)
Blinking red (8 sec interval)
Blinking red (12 sec interval)
The projector is in standby mode and cannot be
turned on.
The projector is in standby mode and cannot be
turned on.
The projector is in standby mode and cannot be
turned on.
Lamp error
The projector is in standby mode and cannot be
turned on.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Problems & Solutions
Problem
Check These Items
Does not turn on
• Check that the power cable is plugged in and that the power button on the projector cabinet or the
remote control is on.
• Ensure that the lamp cover is installed correctly. See page 44.
• Check to see if the projector has overheated or the lamp usage exceeds 1100 hours (up to 1600 hours
: Normal mode). If there is insufficient ventilation around the projector or if the room where you’re
presenting is particularly warm, move the projector to a cooler location.
No picture
• Use the menu to select your source (Video, S-Video, RGB or PC Card Viewer). See page 31.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page 31.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Factory Default in the Adjustment
Menu. See page 33.
Image isn’t square to the screen
• Reposition the projector to improve its angle to the screen. See page 23.
• Use the Keystone in the Adjustment Menu to correct the trapezoid distortion. See page 32.
Picture is blurred
• Adjust the focus. See page 23.
• Reposition the projector to improve its angle to the screen. See page 23.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens.
See page 14.
• Use menus or Source button on the remote control or the cabinet to select the source you want to input.
Image is scrolling vertically, hori-
zontally or both
• Install new batteries. See page 13.
Remote control does not work
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. See page 13.
• See the Status Light messages above.
Status indicator is lit or blinking
Cross color in RGB mode
• IfAutoAdjust is off, turn it on. IfAutoAdjust is on, turn it off and balance the image with the Position/
Clock in the Image Options. See page 33 or 36.
When using the PC Card Viewer function
Problem
Check These Items
No picture
• Is “PC Card Viewer” selected from the Source menu?
• Is the CompactFlash memory card seated in the PC CARD slot completely?
• Are slide data stored in the CompactFlash memory card?
• Have the contents of the CompactFlash memory card been destroyed?
Part of a slide is not displayed
• While an image with over 1024
ן 768 dots is projected, several lines of information will be lost. Contents of CompactFlash Card • Use a computer, etc., to repair the data.
are damaged
For more information contact your dealer.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
6. SPECIFICATIONS
This section provides technical information about the DLV-100 Projector's performance
Model Number
DLV-100
Optical
DMD™
Lens
Single Chip Digital Micromirror Device(DMD™), 1024x768 dots
Manual zoom, Manual focus: F2.6 – 2.8 f= 28.3 – 34.0mm
135 W NSH lamp
Lamp
(The lamp is warranted for 1000 hours of operation time within 6 months.)
30 - 200 inches (0.8 - 5.1 m) diagonal
Image Size
Projection Distance
3.8 – 31.7ft (1.16 – 9.67m)
Electrical
Inputs
Video (NTSC / PAL / PAL-N / PAL-M / PAL60 / SECAM / NTSC4.43)
Horizontal Frequency : 15 -100 kHz (RGB : 24 kHz or over)
Vertical Frequency : 50 -120 Hz
Video Bandwidth
RGB: 80 MHz (-3dB)
Color Reproduction
Horizontal Resolution
Full color, 16.7 million colors simultaneously.
550 TV lines : NTSC / PAL / YCbCr
300 TV lines : SECAM
RGB 1024 dots horizontal, 768 dots vertical
100 - 120 / 200 - 240 V AC, 50 / 60 Hz
2.2 A (100 -120 V AC) / 1.1A (200 -240 V AC)
Power Requirement
Input Current
Mechanical
Dimensions
Net Weight
9.6" (W) x 2.1" (H) x 7.7" (D) / 243mm (W) x 53mm (H) x 196mm (D) (not including protrusions)
3.3 lbs / 1.5 kg
Environmental Considerations Operational Temperatures : 41˚ to 95˚F (5˚ to 35˚C), 20 to 80% humidity
Storage Temperatures :14˚ to 122˚F (-10˚ to 50˚C), 20 to 80% humidity
Regulations
UL Approved (UL 1950, CSA 950)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
The specifications are subject to change without notice.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabinet Dimensions
P C C O N T R O L
U S B
A C I N ~
V I D E O
R G B
S - V I D E O
P C C A R D
A U D I O
A C C E S C S A P R C D
P O W E R
S T A T U S
S T A N D B Y
O N
A D J U S T
A U T O
S O U R C E
/
S E L E C T
196 (7.7”)
238 (9.4”)
243 (9.6”)
43.5 (1.71”)
Lens center
Lens center
53 (2.1”)
8 (0.31”)
29.5 (1.16”)
Unit = mm (inch)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
D-Sub Pin Assignments
Mini D-Sub 15 Pin Connector
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
5
4
3
2
1
10
9
8
7
6
15 14 13 12 11
Pin No.
RGB Signal (Analog)
YCbCr Signal
1
2
Red
Cr
Y
Green or Sync on Green
Blue
3
Cb
4
Ground
5
Ground
6
Red Ground
Green Ground
Blue Ground
No Connection
Sync Signal Ground
Cr Ground
Y Ground
Cb Ground
7
8
9
10
11
12
13
14
15
Bi-directional DATA (SDA)
Horizontal Sync or Composite Sync
Vertical Sync
Data Clock
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Compatible Input Signal List
Resolution
( Dots )
Frequency H.
( kHz )
Refresh Rate
( Hz )
Dot Clock
( MHz )
Signal
NTSC
PAL
SECAM
VESA
IBM
MAC
MAC
MAC
VESA
VESA
IBM
VESA
IBM
VESA
IBM
IBM
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
SUN
–
–
–
15.734
15.625
15.625
31.47
31.47
31.47
34.97
35
60
50
50
59.94
60
-
-
-
640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 720
ן 350 720
ן 400 720
ן 350 720
ן 400 800
ן 600 800
ן 600 800
ן 600 800
ן 600 800
ן 600 832
ן 624 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1152
ן 864 1152
ן 870 1152
ן 900 1152
ן 900 1280
ן 960 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 25.175
25.175
25.175
31.334
30.24
31.5
31.5
31.49
36
28.322
40
35.5
35.5
36
40
50
49.5
56.25
57.283
44.9
65
60
66.67
66.67
72.81
75
37.86
37.5
39.375
43.269
31.469
37.927
39.44
39.44
35.16
37.879
48.077
46.88
53.674
49.725
35.5
48.363
57.476
60.241
60.023
68.677
67.5
68.681
61.796
71.736
60
64.286
65.2
78.125
81.13
79.976
91.146
33.75
28.13
45
31.47
15.73
75.0
75
85.01
70.09
85.04
87.85
87.85
56.25
60.32
72.19
75
85.06
74.55
43 Interlaced
60
70.07
74.93
75.03
85
75
75.6
75
80
78.75
94.5
108
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
100
65.95
76.05
60
92.94
105.6
108
108
118.5
135
135
135
157.5
74.25
74.25
74.25
27
–
162
175.5
189
202.5
SGI
VESA
VESA
MAC
HP
SUN
VESA
VESA
60.02
69.89
72.01
76.11
75.03
85.02
60 Interlace
50 Interlace
60 Progressive
59.94 Progressive
59.9 Interlace
60
HDTV (1080i)(1125i) 1920
ן 1080 HDTV (1080i)(1125i) 1920
ן 1080 HDTV (720p)(750p)
SDTV (480p)(525p)
SDTV (480i)(525i)
VESA
VESA
VESA
VESA
1280
ן 720 –
–
1600
ן 1200 1600
ן 1200 1600
ן 1200 1600
ן 1200 81.3
87.5
93.75
65
70
75
#: Images in above flagged with # are compressed with Advanced AccuBlend.
NOTE1: Some composite sync signals may not be displayed correctly.
NOTE2: Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or
resolution on your PC. Refer to Display Properties help section of your PC for procedures.
NOTE3: UXGA (1600
ן 1200) is supported for separate sync signal only. 50
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Control Codes
Cable Connection
Communication Protocol
Baud rate:
Function
Code Data
38400 bps
8 bits
POWER ON
02H 00H 00H 00H 00H 02H
Data length:
Parity:
POWER OFF
02H 01H 00H 00H 00H 03H
No parity
One bit
None
Stop bit:
X on/off:
INPUT SELECT RGB
INPUT SELECT VIDEO
02H 03H 00H 00H 02H 01H 01H 09H
02H 03H 00H 00H 02H 01H 06H 0EH
Full duplex
Communications
procedure:
INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H
INPUT SELECT PC CARD VIEWER
PICTURE MUTE ON
PICTURE MUTE OFF
SOUND MUTE ON
02H 03H 00H 00H 02H 01H 1FH 27H
02H 10H 00H 00H 00H 12H
02H 11H 00H 00H 00H 13H
02H 12H 00H 00H 00H 14H
02H 13H 00H 00H 00H 15H
02H 14H 00H 00H 00H 16H
02H 15H 00H 00H 00H 17H
PC Control Connector (DIN-8P)
To RxD of PC
SOUND MUTE OFF
8
6
7
ON SCREEN MUTE ON
ON SCREEN MUTE OFF
5
4
3
2
1
NOTE: Contact your local dealer for a full list of PC Control Codes if needed.
To GND of PC
To TxD of PC
NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Integra Division of
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
E
SN 29343259A
W0109-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|