OPERATOR’S MANUAL
PD03P-XXX-XXX
RELEASED: 12-17-05
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
REVISED:
6-25-13
(REV. F)
3/8” DIAPHRAGM PUMP
1:1 RATIO, NON-METALLIC
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637428 for air section repair (see page 6).
637429-XX for fluid section repair (see page 4)
.
PUMP DATA
Models . . . . . . see Model Description Chart for “-XXX”.
Pump Type . . . Air Operated Double Diaphragm.
Material . . . . . see Model Description Chart.
Weight. . . . . . . . PD03P-XDS-XXX. . . . . . . 4.16 lbs (1.89 kgs)
PD03P-XES-XXX. . . . . . . . 4.26 lbs (1.93 kgs)
PD03P-XKS-XXX . . . . . . . 4.50 lbs (2.04 kgs)
PD03P-XLS-XXX . . . . . . . 4.62 lbs (2.10 kgs)
PD03P-XPS-XXX . . . . . . . 3.44 lbs (1.56 kgs)
PD03P-XRS-XXX . . . . . . . 3.50 lbs (1.59 kgs)
Maximum Air Inlet Pressure . . . . . . . . 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure. . . . . . . . . . 100 p.s.i.g. (6.9 bar)
Air Consumption @ 40 p.s.i.g. . . . . . . . 1 c.f.m /gallon (approx.)
Figure 1
(flooded inlet)
Maximum Flow Rate
MODEL DESCRIPTION CHART
PD03
Center Section Material
- Polypropylene
ball check. . . . . . . . . . . 10.6 g.p.m. (40.1 l.p.m.)
duckbill . . . . . . . . . . . . . 8.7 g.p.m. (32.9 l.p.m.)
X X
P -X X S -X
Displacement / Cycle @ 100 p.s.i.g
ball check. . . . . . . . . . 0.022 gallons (0.083 lit.)
P
duckbill . . . . . . . . . . . . . 0.018 gallons (0.068 lit.)
Fluid Connection
Maximum Particle Size
A
B
- 3/8 - 18 N.P.T.F. - 1
- Rp 3/8 (3/8 - 19 BSP)
ball check. . . . . . . . . . 1/16”dia. (1.6 mm)
duckbill. . . . . . . . . . . . . fibers)
Fluid Caps / Manifold Material
D
E
K
L
P
R
- Groundable Acetal (single port)
- Groundable Acetal (multiple port)
- Kynar PVDF (single port)
Maximum Temperature Limits (diaphragm / ball / seal material)
Acetal . . . . . . . . . . . . . . . . . . . . . . -100 to 1800 F (-120 to 820 C)
E.P.R / EPDM . . . . . . . . . . . . . . . . -600 to 2800 F (-510 to 1380 C)
Hytrel . . . . . . . . . . . . . . . . . . . . . -200 to 1500 F (-29º to 660 C)
Kynar P.V.D.F . . . . . . . . . . . . . . 100 to 2000 F (-12º to 930 C)
Neoprene. . . . . . . . . . . . . . . . . . . 00 to 2000 F (-18º to 930 C)
Nitrile . . . . . . . . . . . . . . . . . . . . . . 100 to 1800 F (-12º to 820 C)
Polypropylene . . . . . . . . . . . . . . 350 to 1750 F (20 to 790 C)
Santoprene . . . . . . . . . . . . . . . -400 to 2250 F (-400 to 1070 C)
- Kynar PVDF (multiple port)
- Polypropylene (single port)
- Polypropylene (multiple port)
Hardware Material
- Stainless Steel
S
Seat Material
D
K
P
- Acetal
S
0
- Stainless Steel
- (Duckbill)
- Kynar PVDF
- Polypropylene
PTFE . . . . . . . . . . . . . . . . . . . . . . 400 to 2250 F (40 to 1070 C)
. . . . . . . . . . . . . . . . . . . . . -400 to 3500 F (-400 to 1770 C)
Viton
Ball Material
(*) Duckbill models
Groundable Models . . . . . . . . . PD03P-XDS-XXX
PD03P-XES-XXX
A
C
J
N
- Santoprene
- Hytrel
S
- Stainless Steel
T
V
K
L
- PTFE
- Viton
- Nitrile (*)
- Neoprene (*)
Dimensional Data . . . . . . . . . . . . . . . . see page 8
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 72.7 db(A)
- EPR (*)
- Viton (*)
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
Diaphragm Material
- Santoprene
- Hytrel
A
C
T
V
- PTFE / Santoprene
- Viton
NOTICE: All possible options are shown in the chart, however, cer-
tain combinations may not be recommended, consult a represen-
tative or the factory if you have questions concerning availability.
FLUID SECTION SERVICE KIT SELECTION
Example: Model # PD03P-ARS-SAA
Fluid Section Service Kit # 637429-AA
PD03P -ARS - S X X
637429 - X
X
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
© 2013
CCN 15255995
Download from Www.Somanuals.com. All Manuals Search And Download.
the material being pumped if the material being pumped
is subject to “setting up” when not in use for a period of
time.
Disconnect the air supply from the pump if it is to be in-
active for a few hours.
The outlet material volume is governed not only by the
air supply but also by the material supply available at the
inlet. The material supply tubing should not be too small
or restrictive. Be sure not to use hose which might col-
lapse.
When the diaphragm pump is used in a forced-feed
(flooded inlet) situation, it is recommended that a Check
Valve”be installed at the air inlet.
GENERAL DESCRIPTION
The ARO diaphragm pump offers high volume delivery even
at low air pressure and a broad range of material compatibility
options available. Refer to the model and option chart. ARO
pumps feature stall resistant design, modular air motor / fluid
sections.
Air operated double diaphragm pumps utilize a pressure dif-
ferential in the air chambers to alternately create suction and
positive fluid pressure in the fluid chambers, ball checks insure
a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will
continue to pump and keep up with the demand. It will build
and maintain line pressure and will stop cycling once maxi-
mum line pressure is reached (dispensing device closed) and
will resume pumping as needed.
y
y
y
y
Secure the diaphragm pump legs to a suitable surface to
insure against damage by vibration.
MAINTENANCE
AIR AND LUBE REQUIREMENTS
Certain ARO “Smart Parts” are indicated which should be
available for fast repair and reduction of down time.
Provide a clean work surface to protect sensitive internal
moving parts from contamination from dirt and foreign
matter during service disassembly and reassembly.
Keep good records of service activity and include pump
in preventive maintenance program.
Service Kits are available to service two separate Dia-
phragm Pump functions: 1. AIR SECTION, 2. FLUID SEC-
TION. The Fluid Section is divided further to match typical
active MATERIAL OPTIONS.
y
y
WARNING
EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
A filter capable of filtering out particles larger than 50
microns should be used on the air supply. There is no lu-
brication required other than the “O” ring lubricant which is
applied during assembly or repair.
y
y
y
y
If lubricated air is present, make sure that it is compatible
with the “O” rings and seals in the air motor section of
the pump.
OPERATING INSTRUCTIONS
Always flush the pump with a solvent compatible with
y
TYPICAL CROSS SECTION
Figure 2
Viton and Hytrel are registered trademarks of the DuPont Company Loctite is a registered trademark of Henkel Loctite Corporation
®
®
®
®
Santoprene is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. Lubriplate is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company)
®
®
PD03P-XXX-XXX (en)
Page 3 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
y
PARTS LIST / PD03P-XXX-XXX FLUID SECTION
637429-XX Fluid Section service kits include: Balls (see BALL OPTION, refer to -XX in chart below), Diaphragms (See DIAPHRAGM
OPTION, refer to -XX in chart below) and item 19 (listed below), plus items 144, 174 and 94276 Lubriplate® grease (page 6).
n
SEAT OPTIONS
PD03P-XXS-XXX
BALL / DUCKBILL OPTIONS
PD03P-XXS-XXX
MATERIAL CODE
[A] = Aluminum
[B] = Nitrile
[D] = Acetal
[E] = E.P.R.
“21”
“22” (5/8” dia.)
n
42”
n
[GA] = Groundable Acetal
[GFN] = Glass Filled Nylon
[H] = Hytrel
[K] = Kynar PVDF
[N] = Neoprene
[P] = Polypropylene
[PPG] = Glass Filled
Polypropylene
-XXX Seat
Qty [Mtl]
-XXX Ball
Qty
[Mtl]
-XXX Duckbill Qty [Mtl]
-DXX 96580-2 (4)
-KXX 96580-3 (4)
-PXX 96580-1 (4)
[D]
[K]
[P]
-XAX 96481-A
-XCX 96481-C
-XSX 96513
(4)
(4)
(4)
(4)
(4)
[Sp]
[H]
-XJX 96744-2
-XNX 96744-3
-XLX 96744-4
(4)
(4)
(4)
[B]
[N]
[V]
[E]
[SS]
[T]
-SXX 96537
-0XX 96745
(4) [SS]
(4) [P]
-XTX 96481-4
-XVX 96481-3
-XKX 96744-1 (4)
[Sp] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
[V]
NOTE: Item 19 “O”ring is not used with PD03P-XXX-0XX seat option.
[V] = Viton
DIAPHRAGM OPTIONS PD03P-XXS-XXX
SERVICE KIT
“7”
“8”
“19”
n
n
n
n
-XX = (Ball)
-XXX -XX = (Diaphragm) Diaphragm Qty [Mtl] Diaphragm Qty [Mtl]
“O” Ring
(3/32” x 1-1/8” o.d.)
Qty
[Mtl]
[E]
-XXA 637429-XA
-XXC 637429-XC
-XXT 637429-XT
-XXV 637429-XV
96533-A
96533-C
96538
(2)
(2)
(2)
(2)
[Sp] -----
[H] -----
---
---
(2)
---
--- 93761
(4)
(4)
(4)
(4)
--- Y325-119
[Sp] 96514
[B]
[T] 96533-A
[V] -----
[T]
96558
--- Y327-119
[V]
MANIFOLD / FLUID CAP OPTIONS PD03P-XXS-XXX
Polypropylene
PD03P-XPS- PD03P-XRS-
Qty Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No.
Kynar PVDF
PD03P-XKS- PD03P-XLS-
Groundable Acetal
PD03P-XDS-
PD03P-XES
(size)
Item Description
[Mtl] Part No.
[Mtl]
(1/4” - 20)
6
Diaphragm Nut
15 Fluid Cap
43 Ground Strap
(2) 93810-7 [P] 93810-7
(2) 96460-1 [P] 96460-1
[P] 93810-3 [K] 93810-3
[P] 96460-3 [K] 96460-3
[K] 93810-2
[K] 96460-2
--- 92956-1
[D] 93810-2
[GA] 96460-2
[SS] 92956-1
[D]
[GA]
[SS]
(1) -----
---
-----
---
-----
--- -----
Ground Kit Assembly
57
(1) -----
---
-----
---
-----
--- -----
--- 66885-1
[K] 96468-2
66885-1
(not shown)
(N.P.T.F.)
60 Inlet Manifold
(1) 96468-1 [P] 96468-7
[P] 96468-3 [K] 96468-9
[GA] 96468-8
[GA]
(BSP)
(1) 96468-4 [P] 96468-10 [P] 96468-6 [K] 96468-12 [K] 96468-5
[GA] 96468-11 [GA]
(N.P.T.F.)
(BSP)
61 Outlet Manifold
(1) 96469-1 [P] 96469-1
(1) 96469-4 [P] 96469-4
[P] 96469-3 [K] 96469-3
[P] 96469-6 [K] 96469-6
[K] 96469-2
[K] 96469-5
[K] -----
[GA] 96469-2
[GA] 96469-5
--- 94478-2
--- 96559-2
[GA]
[GA]
[D]
(N.P.T.F.)
[PPG]
[PPG]
63 Pipe Plug
(1) -----
(1) -----
---
---
94478-1
96559-1
-----
-----
--- 94478-3
--- 96559-3
(BSP)
[K] -----
[D]
COMMON PARTS
Item Description (size)
Qty
Part No. [Mtl]
Item
27 Bolt
29
Description (size)
(1/4” - 20 x 1-1/8”)
Qty Part No.
(12) 96471
(20) 93828
(2) 93264
[Mtl]
1
5
Connecting Rod
Diaphragm Washer
(1/4” - 20 x 1-1/8”)
(1)
(2)
(8)
96532
96556
96471
[SS]
[GFN]
[SS]
[SS]
[SS]
[A]
o
(1/4” - 20)
Nut
26 Bolt
77 Logo Plate
DUAL INLET / DUAL OUTLET KITS 637442-X
Polypropylene
Kynar PVDF
Groundable Acetal
637442-1 (N.P.T.) 637442-4 (BSP) 637442-3 (N.P.T.) 637442-6 (BSP) 637442-2 (N.P.T.) 637442-5 (BSP)
Qty Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl]
(size)
Item Description
17 Dual Outlet Manifold
18 Dual Inlet Manifold
(2) 96520-1 [P] 96520-4
(2) 96519-1 [P] 96519-4
[P] 96520-3 [K]
[P] 96519-3 [K]
96520-6
96519-6
96514
[K] 96520-2 [GA] 96520-5 [GA]
[K] 96519-2 [GA] 96519-5 [GA]
(3/32” x 1-1/8” o.d.)
19 O” Ring
(1) 96514
[T] 96514
[T] 96514
[T]
[T] 96514
[T] 96514
[T]
Smart Parts”keep these items on hand in addition to the service kits for fast repair and reduction of down time.
o
Page 4 of 12
PD03P-XXX-XXX (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PD03P-XXX-XXX FLUID SECTION
COLOR CODE
3
2
1
4
DIAPHRAGM BALL
MATERIAL
COLOR
COLOR
Hytrel
Cream
Tan
Black (
Tan
)
Santoprene
5
6
Viton
Yellow ( )
Yellow ( )
) Dot
(
17
Torque Sequence
FOR THE
AIR MOTOR SECTION
SEE PAGES 6 & 7
61
29
43
1
7
22
21
19
26
29
42
21
77
15
26
22
21
19
27
5
63
6
42
21
60 (PD03P-XES-XXX,
PD03P-XLS-XXX,
PD03P-XRS-XXX)
29
Stainless steel seat installation
60 (PD03P-XDS-XXX,
Radius (ball side)
PD03P-XKS-XXX,
PD03P-XP
S-XXX)
18
Chamfer(fluid inlet side)
View for PD03P-XXS-XXT (PTFE diaphragm)
configuration only
Figure 3
PTFE(white)
7
ASSEMBLY TORQUE REQUIREMENTS
NOTE: DO NOT OVERTIGHTEN FASTENERS.
(6) diaphragm nut, 60 - 70 in. lbs (6.8 - 7.9 Nm).
(29) nut, 50 - 60 in. lbs (5.6 - 6.8 Nm), / alternately and evenly, then re-torque after initial run-in.
LUBRICATION / SEALANTS
Apply Lubriplate (94276) to all “O" rings, ”U" cups and mating parts.
Apply pipe sealant to threads.
Apply anti-seize compound to threads and bolt and nut flange heads which contact pump
case when using stainless steel fasteners.
Apply Loctite 242 to threads.
8
Air Side Santoprene (tan)
PD03P-XXX-XXX (en)
Page 5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PD03P-XXX-XXX AIR MOTOR SECTION
p
Indicates parts included in 637428 Air Section Repair Kit.
Item
101 Center Body
Description (size)
Qty Part No.
(1) 96466
[Mtl]
[PPG]
Item
140 Valve Insert
Description (size)
Qty Part No. [Mtl]
(1) 93276
(1) 96173
[CK]
[CK]
(right side)
103R Cover
103L Cover
(1) 96488
(1) 96489
(1) 96353
(1) 95919
(2) 94874-1
(2) 96092
(12) 96093
(1) 96542
(1) 96531
(1) 96214-1
(4) 96487
(1) 96204
(1) 96352
(3) Y325-29
(1) 94395
(1) 96383
[D]
[D]
141 Valve Plate
(left side)
(1/8” x 3/4” o.d.)
144 “U” Cup Packing
(2) Y187-47 [B]
(1) Y325-24 [B]
p
p
p
(1/16” x 1-1/4” o.d.)
107 Plug, Small
111 Major Valve Spool
118 Actuator Pin
121 Washer
[D]
166 “O” Ring
(includes 168 and 169)
[D]
167 Pilot Piston
(1) 67382
(2) 96459
(1) 96384
(1) 96090
[D]
[U]
[U]
[D]
(1/16” x 7/16” o.d.)
168 “O” Ring
[SS]
[D]
(1/8” x 5/8” o.d.)
169 “U” Cup Packing
170 Spool Bushing
p
p
(#4 - 20 x 1/2”)
123 Screw
[SS]
[P]
(1/16” x 13/16” o.d.)
129 Muffler Baffle
130 Gasket
171 “O” Ring
(2) Y325-17 [B]
(2) Y325-115 [B]
(2) Y325-105 [B]
p
(3/32” x 7/8” o.d.)
173 “O” Ring
[SY]
[B]
p
(3/32” x 11/32” o.d.)
174 “O” Ring
132 Air Manifold Gasket
p
p
p
(1/4” - 20 x 3”)
134 Flange Bolt
135 Valve Block
136 Plug, Large
[SS]
[PPG]
[D]
200 Porting Gasket
(1) 96364
[B]
(1/16” x 3/8” o.d.)
232 “O” Ring
(4) Y325-10 [P]
(4) Y12-4-S [SS]
(1/4” - 20)
236 Nut
(1/16” x 1-5/8” o.d.)
137 “O” Ring
[B]
p
p
p
(1/8” x 1” o.d.)
138 “U” Cup Packing
139 “U” Cup Packing
[U]
Lubriplate FML-2 Grease
(1) 94276
637308
n p
(1/8” x 1-7/16” o.d.)
[U]
Lubriplate Grease, 10 Pack
MATERIAL CODE
AIR MOTOR SECTION SERVICE
[B] = Nitrile
[CK] = Ceramic
[D] = Acetal
[PPG] = Glass Filled Polypropylene
[SS] = Stainless Steel
[SY] = Syn-Seal
Service is divided into two parts - 1. Pilot Valve, 2. Major
Valve.
[P] = Polypropylene
[U] = Polyurethane
Air Motor Section Service is continued from Fluid Section
repair.
y
DIAPHRAGM PUMP SERVICE
GENERAL SERVICE NOTES:
PILOT VALVE DISASSEMBLY
Inspect and replace old parts with new parts as neces-
sary. Look for deep scratches on metallic surfaces, and
nicks or cuts in “O”rings.
y
1. Remove (123) screws, releasing (103) covers, (121) wash-
ers, (118) actuator pins and (167) pilot piston.
2. Remove (170) spool bushing and inspect inner bore of
bushing for damage.
Tools needed to complete disassembly and repair:
y
5/8” socket or wrench, 7/16” socket or wrench, 3/8”
socket or wrench, 5/16” Allen wrench, T-10 Torx
screwdriver, torque wrench (measuring inch pounds),
“O”ring pick.
y
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from ser-
vice kit.
2. Assemble (171) “O” rings to (170) bushing and assemble
bushing into (101) center body.
3. Lubricate and assemble (167) pilot piston assembly into
(170) bushing.
4. Assemble (173 and 174) “O” rings and (121) washers to
(103) covers, then insert (118) actuator pins through as-
sembly.
5. Assemble (144) “U” cups (note the lip direction) and (103)
covers to (101) center body, securing with (123) screws.
NOTE: Tighten (123) screws to 4 - 6 in. lbs (0.45 - 0.68 Nm).
FLUID SECTION DISASSEMBLY
1. Remove (61) top manifold.
2. Remove (19) “O”rings, (21) seats and (22) balls.
3. Remove (60) bottom manifold.
4. Remove (19) “O”rings, (21) seats and (22) balls.
5. Remove (15) fluid caps.
6. Remove (6) diaphragm nut, (7) or (7 / 8) diaphragms and
(5) washer.
7. Remove (1) connecting rod from air motor.
8. Carefully remove remaining (6) diaphragm nut, (7) or (7 / 8)
diaphragms and (5) washer from (1) connecting rod. Do
not mar surface of connecting rod.
MAJOR VALVE DISASSEMBLY
1. Unthread (123) screws, releasing (129) muffler baffle.
2. Unthread (134) bolts and pull (135) valve block and com-
ponents from (101) center body.
3. Remove (132) gasket, (141) valve plate and (140) valve
insert from (135) valve block.
4. Remove (134) bolts, releasing (107 and 136) plugs and
(111) spool.
FLUID SECTION REASSEMBLY
Reassemble in reverse order.
Lubricate (1) connecting rod with Lubriplate or equiva-
lent “O”ring lubricant.
Install (5) washers with i.d. chamfer toward diaphragm.
When replacing PTFE diaphragms, install the 96533-A
Santoprene diaphragm behind the Teflon diaphragm.
y
y
y
y
Page 6 of 12
PD03P-XXX-XXX (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PD03P-XXX-XXX AIR MOTOR SECTION
PILOT VALVE PARTS
144 118
169 168 171
123
103L
173
232
236 130 129
174
121 167 170
140 132
107
137
166
123
144
103R
123
135
134
138
141
200
101
118 121 174 173
PILOT VALVE PARTS
139
137
111
136
ASSEMBLY TORQUE REQUIREMENTS
NOTE: DO NOTOVERTIGHTEN FASTENERS.
(123) screw, 4 - 6 in. lbs (0.45 - 0.68 Nm).
(134)bolt, 15 - 20 in. lbs (1.7 - 2.3 Nm), wait 10 minutes, then re-torque to 15
- 20 in. lbs (1.7 - 2.3 Nm).
MAJOR VALVE
LUBRICATION / SEALANTS
Apply Lubriplate (94276) to all “O" rings, ”U" cups and mating parts.
Figure 4
6. Assemble (140) valve insert and (141) valve plate to
(135) valve block. Note: Assemble (140) valve insert with
dished” side toward (141) valve plate. Assemble (141)
valve plate with identification dot toward (132) gasket.
7. Assemble (132 and 200) gaskets and (135) valve block
to (101) center body, securing with (134) bolts. NOTE:
Tighten (134) bolts to 15 - 20 in. lbs (1.7 - 2.3 Nm).
8. Assemble (130) gasket and (129) muffler baffle to (101)
center body, securing with (123) screws. NOTE: Tighten
(123) screws to 4 - 6 in. lbs (0.45 - 0.68 Nm).
MAJOR VALVE REASSEMBLY
1. Assemble new (139 and 138) U” cups on (111) spool -
LIPS MUST FACE EACH OTHER.
2. Assemble (137) O”rings to (136) large plug.
3. Assemble (137 and 166) O”rings to (107) small plug.
4. Insert (111) spool into (136) large plug, then insert (136)
large plug into (135) valve block, being sure the (111)
spool is rotated to accept (140) valve insert.
5. Assemble (107) small plug into (135) valve block.
PD03P-XXX-XXX (en)
Page 7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Pump blows air out main exhaust when stalled on either
stroke.
Product discharged from air exhaust.
Check for diaphragm rupture.
y
y
Check air supply.
Check tightness of (6) diaphragm nut.
y
y
y
Check for plugged outlet hose.
For the pump to prime itself, it must be mounted in the
vertical position so that the balls will check by gravity.
Check for pump cavitation - suction pipe should be sized
at least as large as the inlet thread diameter of the pump
for proper flow if high viscosity fluids are being pumped.
Suction hose must be non-collapsible type, capable of
pulling a high vacuum.
Air Bubbles in product discharge.
Check connections of suction plumbing.
Check “O”rings between intake manifold and fluid caps.
Check tightness of (6) diaphragm nut.
y
y
y
y
Pump blows air out main exhaust when stalled on either
stroke.
Check all joints on intake manifolds and suction connec-
tions. These must be airtight.
Inspect the pump for solid objects lodged in the dia-
phragm chamber or the seat area.
Check “U”cups on (111) spool in major valve.
Check (141) valve plate and (140) insert for wear.
Check (169) U”cup on (167) pilot piston.
y
y
y
y
y
DIMENSIONAL DATA
Dimensions shown are for reference only, they are shown in inches and millimeters (mm).
Air Inlet 1/4 - 18 P.T.F. SAE Short
7-31/32"(202.3 mm)
4-13/32"(110.5 mm)
Exhaust Port 1/2 - 14 N.P.T.F. - 1
5-23/32" (145.2 mm)
4-31/32"(125.6 mm)
9-5/16"
(236.2 mm)
8-17/32"
(216.1 mm)
4-3/8"
(111.0 mm)
1-3/32"
(27.8 mm)
1-9/32"
(32.1 mm)
9/32" Slot
2-13/16"
3/8"(9.6 mm)
4-1/16"(102.7 mm)
4-13/16"(121.9 mm)
(7.2 mm)
(71.4 mm)
5-5/8" (142.7 mm)
Pump Model
“A" Material Inlet
“B" Material Outlet
PD03P-AXS-XXX
PD03P-BXS-XXX
3/8 - 18 N.P.T.F.
Rp 3/8 (3/8 - 19 BSP, parallel)
3/8 - 18 N.P.T.F. - 1
Rp 3/8 (3/8 - 19 BSP, parallel)
Figure 5
Page 8 of 12
PD03P-XXX-XXX (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
67388 WALL MOUNT BRACKET ASSEMBLY
96507 Wall Mount Bracket
Y13-3-T Washer (3) (3/16")
(#10)
Y14-10-S Lock Washer (3)
Y154-52-S Cap Screw (3)
(#10 - 24 x 1/2")
Figure 6
PD03P-XXX-XXX (en)
Page 9 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 10 of 12
PD03P-XXX-XXX (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PD03P-XXX-XXX (en)
Page 11 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PN 97999-1180
Page 12 of 12
PD03P-XXX-XXX (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
|