IDL 530
IDL 535
Dishwasher
Installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
must be performed, disconnect the appliance from the power
supply.
Carefully read the instructions contained in this manual, as
they provide important information which is essential to safe
and proper installation, use and maintenance of the
appliance.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash
cycle.
8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.
9. The door should not be left open as it may create a
dangerous obstacle.
This appliance complies with the following
EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications.
- 97/17/EEC Labelling
-2002/96/EC (Waste Electrical and Electronic Equipment)
10.If the appliance malfunctions, turn off water supply to
the appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "Troubleshooting." If you
cannot resolve the problem, contact a service centre.
11.Appliances which are no longer being used must be
made inoperable by cutting the power supply cord and
removing the door lock.
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that
the appliance is not damaged. If in doubt, contact a
qualified professional.
3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
- We discourage the use of extension cords and multiple
sockets;
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance
To maintain the EFFICIENCY and SAFETY of this
appliance, we recommend:
l call only the Service Centers authorized
by the manufacturer
l always use original Spare Parts
Close-up View (control panel)
"D" Wash cycle
select
knob
Intensive
Time
4
You
Eco
2
eco
Start/Reset
2
1
3
3
Rapid
Soak
25
4
5
4
5
"A" ON/OFF
button
"G" CYCLE PHASE
indicator lights
"B" ON/OFF
indicator light
"R" Start/Reset
button
A. ON - OFF Button
G. Cycle phase indicator lights
R. Start/Reset Button
B. ON - OFF Light
D. Wash cycle select knob
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
J
I
K
L
E. Upper Rack
I. Bottom Sprayer Arm
J. Salt Container Cap
K. Washing Filter
F. Top Sprayer Arm
G. Rack Height Adjustor
H. Lower Rack
L. Detergent and Rinse Aid Dispenser
Technical
characteristics
Width
Depth
cm. 60
cm. 60
cm. 85
Height
Capacity
12 standard place settings
4,3 psi- 145 psi - 0,03 ÷ 1MPa (0,3 ÷10 bar)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
EN
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt ......
Adjusting Salt Consumption
Salt
The dishwasher is designed to allow for adjusting the amount
of salt consumed based on the harness of the water used.
This is intended to optimize and customize the level of salt
consumption so that it remains at
a minimum.
Your Local Water Board can supply
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
the degree of hardness of the
water
in your area.
To adjust salt consumption, pro-
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located
ceed as follows:
beneath the lower rack and
1) Unscrew the cap from the salt
should be filled as follows:
container.
1. Remove the lower rack
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the "_" setting towards the "+"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
and then unscrew and
remove the cap from the salt
container;
2. If you are filling the
container for the first time, fill
it with water;
3. Place the end of the funnel
(supplied) into the hole and introduce about 2 kg of salt. It
is normal for a small amount of water to come out of the
salt container.
Selector
knob
position
Salt
consumption
(grams/cycle)
Hardness of the water
Autonomy
(cycles/2 kg)
4. Carefully screw the cap back on.
°dH
0 - 10
°fH
°mmol/l
0 - 1.7
0 - 17
/
0
/
The salt container should be filled after about every
30 wash cycles.
10 – 25 18 – 44 1.8 – 4.4
25 – 50 45 – 89 4.5 – 8.9
-
MED
+
20
40
60
60
40
25
Warning: To prevent rust from forming, we advise you
to load the salt before starting a wash cycle.
> 50
> 89
> 8.9
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid ....
Rinse Aid
Detergent
This product makes dishes sparkle more as it improves their
drying. The rinse aid container is situated on the inside of the
appliance door; you should refill it when you see the container
is empty by means of indicator “D”.
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the "Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the "C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 4.
Loading the detergent
To open lid "A", press button "B". The cleaning detergent
should be introduced into the two containers "C"and "D"
up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container "D" and replace the lid.
F
C
To obtain the best results from each washing and drying
cycle, powder detergent, rinse aid liquid and salt should
be used.
D
B
C
D
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjustor to a
lower setting.
A
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.
Warning
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishwasher
Load examples
Before placing the dishes in the dishwasher, remove the
larger food particles to prevent the filter from becoming
clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they be allowed to
soak before they are washed. This will eliminate the need
for extra wash cycles.
Top Rack
Bottom Rack
Pull out the racks to facilitate loading the dishwasher.
How to Use the Lower Rack
We recommend that you place the most difficult to clean
items on the bottom rack: pots, pans, lids, serving dishes
and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the
sides of the racks in order to avoid blocking the rotation
of the top spray arm.
- Pots, serving bowls, etc. must always be placed top
down.
- Deep pots should be slanted to allow the water to flow
out.
This basket is equipped with two removable grids: insert
the cutlery one by one into the slots; (fIg. A) Knives and
other utensils with sharp edges must be placed in the
cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments
on the upper rack.
- Especially long utensils should be placed in the horizon-
tal position at the front of the upper rack.
How to Use the Upper Rack
The upper rack is designed to hold more delicate and
lighter dishware, such as glasses, coffee and tea cups
and saucers, as well as plates, small bowls and shallow
pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not
get moved by the spray of water.
Fig. A
B
How to adjust the Upper rack ...
1
2
4
The top rack can be adjusted using the two rack heights
(top and bottom). To adjust the rack, open up the tabs
that lock the guides and pull out the rack. Arrange the
rack with the back wheels in either the top or bottom
position and then insert it along the guides until the front
wheels are on as well. Close the tabs to lock the rack in
place (see Fig. F).
3
F
A
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Appliance
First of all.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
Turn on the water tap completely and press ON-OFF button
"A". you will hear a short beep and indicator light "B" lights
up.
comes back on or when the door is shut.
Now the appliance is on and awaiting instructions.
At the end of the wash cycle….
Starting and selecting the cycle.
The end of the wash cycle is indicated by two short beeps
Turn the cycle selector knob "D" clockwise until the reference
notch on the knob corresponds with the number or symbol
for the cycle you wish to set (consult the wash cycle table on
page 7, especially when first using the appliance).
If the appliance door is shut, press the Start button "R" and
you will hear a beep; the cycle will start up within a few
seconds.
and the flashing of the drying phase indicator light.
Warning:
Turn the appliance off by pressing button" A ", unplug
the appliance from the electricity socket to cut off the
power supply; the power supply cable should consequently
be easily accessible.
Cycle phase indicator lights
The dishwasher is provided with 4 indicator lights "G" which
come on in sequence as the appliance is performing that
specific phase of the wash cycle.
• Turn off the water tap.
• Wait a few minutes before unloading the dishes: if you
wait a little while, they dry better thanks to the steam.
• Empty the lower rack first.
These phases are:
Warning: when you open the dishwasher door after the wash
cycle has just ended or is under way, take care not to scald
yourself with the hot steam.
pre-wash, wash,
rinses,
drying
Cancelling or modifying a wash cycle in progress…..
Premise: You can cancel the wash cycle in progress, if it has
only just started.
To modify a wash cycle, keep the RESET button "R" pressed
for about 5 seconds: a prolonged beep will sound, followed
by three short beeps. Indicator light "G" will turn off and at
this point, all the settings will have been cancelled.
To select a new wash cycle, repeat the operations illustrated
in the paragraph entitled "starting and selecting the cycle"
Warning: the knob must be turned clockwise from wash
cycle 1 to 5, an anti-clockwise from wash cycle 5 to 1.
If you have left out a dish…
You can interrupt a wash cycle by pressing the ON-OFF
button, then place the dishes you had left out into the
appliance, which will start up from where it was interrupted
when you turn it back on.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer,
cleaner results.
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in
the dishwasher, reduce the amount of detergent used accordingly.
The number and type of wash cycles varies according to the model of dishwasher.
Was h cycle
Detergent
duration
Cycle selection
instructions
for pre- Rinse
Cycle
Cycle description
(tolerance
10% )
wash +
wash
Aid
Hrs. Min.
Pre-wash with hot water at 40°C
Wash at 65°C.
Very dirty dishes and
pans (not to be used
for delicate items).
2 cold rinses
5+25 gr.
30 gr.
2:00'
1:28'
2:25'
0:25'
0:12'
*
1) Intensive
2) Time4You
3) Eco
Rinse with hot water at 70°C.
Drying.
Wash at 50°C.
Cold rinse
Rinse with hot water at 70°C.
Drying.
Normally dirty pans
and dishes. Standard
daily cycle.
*
Environmentally-friendly
cycle, with low energy
consumption levels,
suitable for normally
dirty pans and dishes.
2 Cold pre-washes
Wash at 50°C
Hot rinse at 65°C
Drying
5+25 g
25 gr.
*
Economic and fast
cycle to be used for
slightly dirty dishes.
Run cycle immediately
after use. No drying.
Short wash at 47°C.
Rinse with hot water at 62°C.
4) Rapid 25'
5) Soak
Preliminary wash cycle
for dishes and pans
Short cold wash to prevent food
awaiting completion of from drying onto the dishes.
the load with the dishes
from the next meal.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent odors
from forming and food from caking onto the dishes, you
can run the hold cycle.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishwasher in Shape
After Every Wash
When You Go on Holiday
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
No Solvents or Abrasive Cleaning Products
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Rather, use
only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
Seals
One of the factors that cause odors to form in the dishwasher
is food that remains trapped in the seals. Periodic cleaning
with a damp sponge will prevent this from occuring.
Disposal of old electrical appliances
The crossed out "wheeled bin" symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected.
The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact
on human health and the environment.
Consumers should contact their local authority or retailer for
information concerning the correct disposal of their old
appliance.
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
The filter assembly
If you want consistent good results from your dishwasher,
you need to clean the filter assembly.
The food particles are removed from the wash water, allowing
it to be recirculated during the
cycle, filtered perfectly. For this
The dishwasher is not to be used without filters. Improper
replacement of the filters may reduce the efficiency of the
wash and even damage your dishwasher.
Cleaning the sprayer arms.
1
Food residue may become encrusted onto the sprayer arms
and block the holes where water comes out. Check the
sprayer arms regularly and clean them once in a while
(letters F and I “How is it made?”).
reason, it is a good idea to
remove the larger food
particles trapped inside the
cup “C” and the semi-circular
filter A after each wash; pull
the cup handle upwards to
remove them. Just rinse them
under running water.
A
B
2
C
The entire filter assembly should be cleaned thoroughly once
a month: cup C + semi-circular filter A + cylindrical filter B.
Rotate filter “B” anticlockwise to remove it.
For cleaning, use a non metallic brush.
Reassemble the filter parts (as shown in the figure) and
reinsert the whole assembly into the dishwasher. Position it
into its housing and press downwards.
Troubleshooting
Tap off alarm
It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, let us see what can
be done first: have you forgot to press one of the buttons or to
perform an essential operation?
If you have forgotten to turn the water tap on, your appliance will
remind you of this by sounding a few short beeps for a few minutes.
Turn the tap on and your appliance will start up again after a few
minutes. Were you to be absent when these beeps are sounded, the
appliance will be blocked automatically and indicator lights 2 and 3
(wash and rinses) will flash rapidly. Turn the appliance off at the ON-
OFF button, turn on the water tap and wait approximately 20
seconds before turning the appliance back on; repeat the
programming operations and the selected wash cycle will start up
again.
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Clogged filter alarm
If the appliance is blocked and indicator lights 1 (pre-wash) and 3
(rinses) flash rapidly, this means the filter is clogged by large particles
of food residue. Turn the appliance off, clean the filter thoroughly
and reposition it in its seat as illustrated on this page. Then turn it
back on. Repeat the programming operations and the wash cycle
will start up again.
Have you put the right amount of detergent into the dispenser?
Is the wash cycle suitable for the dishes you have placed inside the
appliance?
Water load solenoid valve malfunction alarm.
If indicator light 2 (wash) flashes rapidly, TURN the dishwasher OFF
AND BACK ON AGAIN after one minute. If the alarm persists, first
turn off the water tap to avoid any flooding and then cut off the
electricity supply and call for technical assistance.
Are the filter and microfilter clean?
Can the sprayer arms turn freely?
The Dishwasher Does Not Drain
Have you checked whether:
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service
centre and provide them with the following information:
- the nature of the problem;
- the model type number (Mod. ...) and the serial number (S/N ....),
which are indicated on the plate located on the side of the inner
part of the door.
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
Error messages.
Never call on unauthorised technicians and refuse to allow
parts to be installed that are not original spare parts.
Your dishwasher is equipped with a safety system which is able to
detect any operating anomalies. These anomalies are reported by
one or two wash cycle indicator lights "G" flashing rapidly.
Take a note of which lights are flashing, turn the appliance off and
call for technical assistance.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Drain Hose Connection
Positioning the Appliance
Fit the drain pipe into a drain line with a minimum diameter
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned to
the right or the left to facilitate proper installation.
of 4 cm or place it over the sink.
Avoid restricting or bending it.
A
Use the special plastic elbow
provided (see figure) to position
it in the best possible way. The
part of the pipe marked with the
letter A should be between 40
and 100 cm above the ground.
The pipe should not be
immersed in water.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher, making
it level. In any case, the appliance should not be inclined
more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
Electrical Connection
After making sure that the voltage and frequency values for
the current in the home correspond to those on the rating
plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
This dishwasher model can be built under a single worktop
(please read the relevant instruction sheet).
Anti-flooding protection
Your dishwasher is provided with a special system which
blocks the water supply in the event of leaks inside the
appliance.
Cold water connection.
This electric household appliance should be connected to
the water mains using the cold water supply hose provided
with the appliance only. Do not use a different hose. In the
event of replacements, use original spare parts only.
Connect the cold water supply hose to a 3/4 gas threaded
connection, taking care to screw it tightly onto the tap.
If the water hoses are new or have been out of use for an
extended period of time, let the water run to make sure it is
clear and free of impurities before making the connection. If
this precaution is not taken, the water inlet could get blocked,
causing damage to your dishwasher.
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical Service
Centres for the replacement.
Caution: the dishwasher plug must be accessible even
when the appliance is installed as a built-in unit so that
maintenance can be done safely.
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of 60°
C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
Removing the plug:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
CROSS-BAR
CORD GRIP
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above
CAUTION:
Once the appliance has been installed, the electrical plug
and socket should remain accessible.
- If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in
order to prevent all potential hazards. (See Assistance)
- The cable should not be bent or compressed.
- The Company shall not be held responsible for any incidents
that occur if these regulations are not observed.
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Viale Aristide Merloni 47
60044 Fabriano (AN) Italy
Tel +39 0732 6611
Download from Www.Somanuals.com. All Manuals Search And Download.
|