Dishwasher
Instruction for installation and use
DE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
must be performed, disconnect the appliance from the
power supply.
Carefully read the instructions contained in this manual, as
they provide important information which is essential to
safe and proper installation, use and maintenance of the
appliance.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash
cycle.
This appliance complies with the following
EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications.
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that
the appliance is not damaged. If in doubt, contact a
qualified professional.
3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.
9.If the appliance malfunctions, turn off water supply to
the appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "Troubleshooting." If you
cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.
To maintain the EFFICIENCY and SAFETY of this
appliance, we recommend:
- We discourage the use of extension cords and multiple
sockets;
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance
- l call only the Service Centers authorized
by the manufacturer
- l always use original Spare Parts
Close-up View (control panel)
B
E
F
H
D
I
M
1
1
2
Reset
2
25
70
55
45
50
55
50
7
3
4
6
5
N
A
G
L
C
Cycle phase under way indicator
Delayed start indicator light
Upper or lower rack selection button
Multifunction numeric indicator
Cycle selection knob
ON-OFF Button
ON-OFF Indicator light
Door handle
Delayed start setting button
Low salt indicator light
M
N
Rack indicator
Low rinse aid indicator light
GB
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
J
K
I
L
Upper Rack
Bottom Sprayer Arm
Salt Container Cap
Top Sprayer Arm
Rack Height Adjustor
Lower Rack
Washing Filter
Detergent and Rinse Aid Dispenser
Technical characteristics
Width
cm. 44,5
cm. 60
cm. 85
Depth
Height
Capacity
8 standard place settings
20 KPa÷ 1MPa (0,2 ÷10 bar)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
GB
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt ......
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The dishwasher is designed to allow for adjusting the
amount of salt consumed based
on the harness of the water
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
used. This is intended to
optimize and customize the
level of salt consumption so that
it remains at a minimum.
Your Local Water Board can
supply the degree of hardness
of the water
in your area.
To adjust salt consumption, pro-
ceed as follows:
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the "_" setting towards the "+"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
Loading the Salt into the Softener
Always use salt intended
for use with dishwashers.
The salt container is
located beneath the
lower rack and should be
filled as follows:
1. Remove the lower rack
and then unscrew and
remove the cap from the
salt container;
2. If you are filling the
container for the first
time, fill it with water;
3. Place the end of the funnel (supplied) into the hole and
introduce about 2 kg of salt. It is normal for a small amount
of water to come out of the salt container.
4. Carefully screw the cap back on.
Water Hardness
The salt container should be filled up when the low
salt indicator light "E" flashes.
Once you have loaded the salt for the first time, it is normal
that the low salt indicator light stays on or flashes for 5
consecutive cycles.
Salt
Autono-
consu-
Clarke
degrees
Selector
position
my
°fH
mmol/l
mption
(grams/-
cycle)
(cycles\2-
kg)
0 - 14
0 - 17
0 -1,7
/
0
/
Warning: To prevent rust from forming, we advise you to
load the salt before starting a wash cycle.
14 - 36 18 - 44 1,8 - 4,4
36 - 71 45 - 89 4,5 - 8,9
"-"
20
40
60
60
40
25
MED
"+"
>71
> 89
> 8,9
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid ....
Detergent
Rinse Aid
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the "Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
This product makes dishes sparkle more as it improves their
drying. The rinse aid container is situated on the inside of
the appliance door; you should refill it when you see the
container is empty by means of indicator “D”.
(If your dishwasher is fitted with a “low rinse aid” indicator
light, fill the container up when the indicator light flashes or
lights up).
Loading the detergent
To open lid "A", press button "B". The cleaning detergent
should be introduced into the two containers "C"and
"D" up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the "C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 2.
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container "D" and replace the lid.
B
F
D
C
D
15 gr.
5 gr.
C
A
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjustor to
a lower setting.
Warning
Three-in-one dishwasher tablets are now available on the market, and combine the detergent, salt and rinse
aid all in one. If the water in your area is hard or very hard, we still recommend you pour extra salt into the
relevant dispenser to prevent the formation of white streaks on your dishes or on the appliance interior.
In any case, please read the manufacturer's instructions provided on the packet.
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishwasher
Load examples
Before placing the dishes in the dishwasher, remove the
larger food particles to prevent the filter from becoming
clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they be allowed to
soak before they are washed. This will eliminate the need
for extra wash cycles.
Top Rack
Top Rack
Pull out the racks to facilitate loading the dishwasher.
How to Use the Lower Rack
We recommend that you place the most difficult to clean
items on the bottom rack: pots, pans, lids, serving dishes
and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides
of the racks in order to avoid blocking the rotation of the
top spray arm.
Lower Rack
Lower Rack
- Pots, serving bowls, etc. must always be placed top
down.
- Deep pots should be slanted to allow the water to flow
out.
- The bottom rack features fold down tine rows (see
figure B) so that larger or more pots and pans can be
loaded.
- Silverware should be placed in the silverware basket
with the handles at the bottom; If the rack has side
baskets, the spoons should be loaded individually into
the appropriate slots (see fig. A).
Fig. B
Especially long utensils should be placed in the horizon-
tal position at the front of the upper rack.
1
How to Use the Upper Rack
The upper rack is designed to hold more delicate and
lighter dishware, such as glasses, coffee and tea cups
and saucers, as well as plates, small bowls and shallow
pans (as long as they are not too dirty).
2
- Position the dishes and cookware so that they do not
get moved by the spray of water.
How to adjust the Upper rack ...
The top rack can be adjusted using the two rack heights
(top and bottom). To adjust the rack, open up the tabs
that lock the guides and pull out the rack. Arrange the
rack with the back wheels in either the top or bottom
position and then insert it along the guides until the front
wheels are on as well. Close the tabs to lock the rack in
place (see Fig. F)
1
2
4
Fig. A
3
Fig. F
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Appliance
How to start a wash cycle
this point, all the settings will have been cancelled.
After performing all the operations described in the previous
chapters, turn the water tap on completely, press ON-OFF
button "A"; you will hear a short beep and indicator light
"B" will come on.
To select a new wash cycle, repeat the instructions contained
in the paragraph entitled "Starting and setting the cycle".
You've left out a dish?
The display turns on and 3 dashes appear: these indicate
that the appliance is awaiting instructions.
You can interrupt a wash cycle by pressing the "ON-OFF"
button, then place the forgotten dishes into the appliance,
which will start up from where it was interrupted when you
turn it back on.
Starting and setting the cycle.
Turn the cycle selector "M" until the reference notch on the
knob corresponds with the symbol or number of the cycle
you wish to set (consult the wash cycle table contained in
this manual, especially when first using the appliance).
After a few seconds, a beep indicates the wash cycle has
started and indicator "G" displays the symbol corresponding
to the phase with which it has begun. The counter "L" will
indicate the estimated amount of time left until the end of
the wash cycle.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when you shut the door.
How to programme extra drying.
If you want your dishes to be perfectly dry, follow the
instructions below.
Do not expect a precise countdown as the wash cycle starts
with an estimated cycle time that is updated as the cycle
progresses and according to a number of parameters that
affect the cycle itself (such as water hardness, the tempera-
ture of the water, the degree of soil, etc.).
Set the knob to RESET and make any specific settings, such
as:
-
-
upper or lower rack
delayed start
Start the wash cycle by turning the knob and open the
appliance door. Observe symbol for drying: it will flash
You want to wash on one rack only? Remember to use
half the amount of detergent.
If you only have a few dishes to wash, you can load these
onto one rack only, saving on both water and electricity.
Press button "I", a beep will sound and indicator "N" appears
on the display. Each time you press the button, a beep will
for about 4 seconds, while the word "OFF" appears on the
display (extra drying disabled).
If you press button "I" immediately, you will hear a prolonged
beep and the word "ON" will appear on the display: the
extra drying has been enabled.
Once you have made your selection, shut the appliance door;
a beep will sound and the wash cycle will either start
immediately or after the delay, wherever set.
sound and symbol
corresponding to the upper rack or
symbol corresponding to the lower rack will appear. If
Remember that with extra drying, the wash cycle will last
longer, to provide you with drier dishes.
you press the button once more, the selection will be reset
and the dishwasher will consequently wash on both racks.
To use the racks correctly, we recommend you read the
chapter entitled "Loading the dishes".
At the end of the wash cycle
At the end of the wash cycle, 2 beeps are sounded and the
word END flashes. Bring the selector back to the RESET
position, and the 3 dashes for programming cancellation
will appear.
Turn the appliance off by pressing the ON-OFF button, turn
off the water tap and open the door. Wait a few minutes
before removing the dishes: this way you won't have to
handle them while they're still hot and they will dry better.
Empty the bottom rack first.
Cycle phase under way indicator
Your dishwasher is equipped with an indicator "G"
comprising 4 symbols which represent the different phases
of a wash cycle. When the wash cycle has started, the display
will indicate the phases under way in sequence.
These phases are:
Make sure the wash cycle has ended before removing the
dishes!
pre-wash
wash
rinses
drying
Warning
Cancelling and modifying a wash cycle in progress
Premise: a wash cycle in progress can only be modified if it
hasn't been running for long.
To modify it, turn the knob and set it to RESET. After a few
seconds, you will hear 4 beeps, indicator "G" relating to the
phase under way will turn off and 3 dashes will appear. At
If opening the door soon after the end of the programme,or
during it, stand away from the Dishwasher, to avoid possible
injury from hot steam.
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a delayed start on a wash cycle
When you have loaded the dishes, you can choose when to
start your dishwasher before setting the wash cycle desired.
l
Press button "D" and you can delay the start of the
wash cycle by 1 to 9 hours. Press the button once, a beep
will sound and the wording "09 h" will come up on the
display. Then, each time you press the button a beep will
sound and the hours will decrease by one hour until the
delay is 01 h. If you press the button once again, the delayed
start is reset and 3 dashes appear on the display.
Note: the delayed start is also reset automatically should
you fail to select the wash cycle on knob "M" within 15
seconds.
l
Once you have set the delayed start time, select the
wash cycle on the knob: after the beep sounds, you will see
indicator light "H" flash on the display and the countdown
begins (indicated on the display one hour at a time). A quick
look at the indicator lights will keep you informed of the
countdown progress at all times.
Have you changed your mind?
w
During the countdown, you can modify the delay by
pressing button "D" repeatedly without resetting the
wash cycle.
w
If you have changed your mind and wish to start the
wash cycle immediately, press button "D" until the
countdown is fully reset. Indicator light "H" will turn
off and the cycle will start at the sound of a beep.
The indicator light corresponding to the cycle phase under
way will come up on the display and the countdown to the
estimated cycle end begins.
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Detergent
for pre-
wash +
wash
Rinse
Aid
Cycle
Cycle selection instructions
Cycle description
Pre-wash with cold water
Pre-wash with hot water at 45°C
Extended wash at 70°C.
Cold rinse
Rinse with hot water at 70°C.
Drying.
Very dirty dishes and pans
(not to be used for delicate
items).
1) Intensive
5+15 gr.
5+15 gr.
15 gr.
*
*
2 pre-washes with cold water.
Extended wash at 55°C.
Rinse with hot water at 70°C.
Drying.
Normally dirty pans and
dishes. Standard daily cycle.
2) Normal
Economic and fast cycle to be
used for slightly dirty dishes.
Run cycle immediately after
use. No drying.
Short wash at 45°C.
Cold rinse.
3) Rapid 25’
Preliminary wash cycle for
dishes and pans awaiting
completion of the load with
the dishes from the next
meal.
Short cold wash to prevent food
from drying onto the dishes.
4) Soak
Economic and fast cycle to be
used for more delicate items
which are sensitive to high
temperatures. Run cycle
immediately after use.
Wash at 50°C.
Lukewarm rinse.
Rinse with hot water at 70°C.
Drying.
5) Crystal care
15 gr.
5+15 gr.
15 gr.
*
*
*
Cold pre-wash.
Extended wash at 55°C.
Cold rinse
Rinse with hot water at 70°C.
Drying.
Normally dirty pans and
6) After dinner dishes with no dry residue.
Economic and fast cycle to be Short wash at 45°C.
used for slightly dirty dishes.
7) Rapid & Dry Run cycle immediately after
use.
Cold rinse
Hot rinse at 70°C.
Drying
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- It is important to try and run the dishwasher when it is
fully loaded in order to save on energy. In order to prevent
odors from forming and food from caking onto the dishes,
you can run the hold cycle.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishwasher in Shape
When You Go on Holiday
After Every Wash
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products. Rather,
use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
Seals
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals. Periodic
cleaning with a damp sponge will prevent this from occuring.
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
The filter assembly
If you want consistent good results from your dishwasher,
you need to clean the filter assembly; this way the food
reinsert the whole assembly into the dishwasher, positioning
it into its housing and pressing downwards.
The dishwasher is not to be used without filters. Improper
replacement of the filters may reduce the efficiency of the
wash and even damage your dishwasher.
particles
removed from the
wash water,
are
1
allowing it to be
r e c i r c u l a t e d
during the cycle,
filtered perfectly.
For this reason, it
is a good idea to
remove the larger
food particles
trapped inside the
Cleaning the Sprayer Arms
It may happen that food
particles become encrusted
on the sprayer arms and
block the holes.Check the
sprayer arms periodically and
clean them when needed
(see “Close-up View
[interior]”, letters F-I).
A
B
2
C
cup “C” and semi-circular filter “A” after each wash. All
you need to do is rinse them under running water; to remove
these, pull the cup handle upwards. The entire filter
assembly, comprising a semi-circular filter “A”, a cup “C”,
and a cylindrical filter “B” should be cleaned thoroughly
once a month. Rotate filter “B” anticlockwise to remove it.
For cleaning, use a non metallic brush.
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter (see figure 2 under
"Installation") located on the outlet of the water supply
tap. After turning off the water tap, unscrew the end of
the water supply hose, remove the filter and clean it carefully
under running water. Then, return the filter to its place and
tighten the water supply hose back into position.
Reassemble the three parts as shown in the figures and
Troubleshooting
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
Error messages.
Your dishwasher is equipped with a safety system which is
able to detect any operating anomalies.
It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first: have you forgot to press one of
the buttons or to perform an essential operation?
The Dishwasher Does Not Start
These anomalies or faults are signalled by several codes
consisting of letters and numbers that flash up on the display.
Make a note of the error code that appears, turn the
appliance off, turn off the water tap and call for technical
assistance.
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
Tap off alarm
If you have forgotten to turn on the water tap, your appliance
will remind you with a long series of prolonged beeps and
the wording H2O will flash up on the display. If you are not
there when the beeps are sounded, you will see the code
H2O flash up on the display. Check that there is water in the
mains supply and turn on the tap; the wash cycle will start
up as normal after a few seconds.
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
Have you put the right amount of detergent into the
dispenser?
Is the wash cycle suitable for the dishes you have placed
inside the appliance?
Are the filter and microfilter clean?
- the nature of the problem;
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.
Can the sprayer arms turn freely?
The Dishwasher Does Not Drain
Have you checked whether:
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Appliance
Drain Hose Connection
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.
Insert the drain hose into a
drain pipe with a minimum
diameter of 4 cm., or let it run
into the sink, making sure to
avoid bending or crimping it.
Use the speical plastic support
that comes with the appliance
(see figure to the right). The
free end of the hose must be
at a height between 40 and
100 cm.and must not be
immersed in water.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
Attention: The special plastic hose support must be solidly
fastened to the wall to prevent the drain hose from moving
and allowing water to spill outside the drain.
This dishwasher model can be built-in under the one
worktop, and it therefore comes provided with an
instructions sheet.
Electrical Connection
Cold Water Connection
After making sure that the voltage and frequency values
for the current in the home correspond to those on the
rating plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Connect the cold water supply hose to a threaded 3/4 (gas)
connector, inserting the small filter supplied with the
dishwasher and making sure
that it is fastened tightly in place
(see figure 2).
If the water pipes are new or
have not been used for an
extended period of time, let the
water run to make sure that the
water is clear and free of
impurities. If this precaution is
not taken, there is a risk that the
water inlet can get blocked and
damage the appliance.
A
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.
Fig.2
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of 60°
C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
Removing the plug:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
Disposing of the plug:
CROSS-BAR
CORD GRIP
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above
CAUTION:
The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.
GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel +39 0732 6611
Fax +39 0732 662501
Download from Www.Somanuals.com. All Manuals Search And Download.
|