InFocus Projector SP LAMP 077 User Manual

Lamp Module Replacement Instructions: SP-LAMP-077  
NOTES:  
Always use the InFocus lamp module designed for your projector model. Using the wrong lamp module may cause premature lamp failure and possible  
damage to the projector.  
projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not liable for the performance,  
safety or certification of any other lamps.  
WARNINGS:  
The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or  
handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace  
Lamp” message.  
To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.  
Unplug the power cord before replacing the lamp.  
Do not drop the lamp module. The glass may shatter and cause injury.  
Do not touch the glass surface of the lamp module. Fingerprints can obscure projection sharpness and may cause the glass to shatter.  
Be extremely careful when removing the lamp module. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp  
module is designed to contain most of these fragments, but use caution when removing it.  
Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.  
When replacing the lamp while the projector is ceiling-mounted, wear protective eyewear to prevent eye injury.  
Hg-Lamp contains mercury. Manage with accordance with local disposal laws. See www.lamprecycle.org  
1. Turn off the projector and unplug the power cord.  
2. Wait 60 minutes to allow the projector and lamp to cool  
thoroughly.  
3. Remove the lamp door, located on top of the projector, by  
removing the screw on the side of the lamp door, sliding  
the door to the left and lifting the lamp door off.  
4. Loosen the captive screws that attach the lamp housing to  
the projector.  
NOTE: If the projector is installed on a ceiling mount, be  
careful not to drop the lamp module once the captive  
screws are loosened.  
5. Carefully lift the lamp straight up, off of the alignment pins;  
being careful not to pinch the lamp connector. Dispose of  
the lamp in an environmentally proper manner.  
6. Install the new lamp module, aligning the pins properly. Be  
careful not to pinch the lamp connector.  
7. Tighten the screws. (NOTE: If the pins have not been  
aligned properly, the screws will not tighten securely.)  
8. Replace the lamp door by reversing step 3 and locking it  
back into place.  
9. Replace the lamp door screw and tighten securely.  
10. Plug in the power cord and press the Power button to turn  
the projector back on.  
11. To reset the lamp hour timer, navigate to the Advanced  
Menu > Status/Service menu and select Reset Lamp  
Hours.  
MDL: IN3924  
FW: 1.02  
(
Advanced Menu  
)
Image  
Source Info...  
Setup  
Status/Service  
Projector Info...  
Reset Lamp Hours...  
Factory Reset...  
Service Code...  
Network Info...  
Basic Menu  
PL739-4800-00  
*PL739-4800-00*  
Download from Www.Somanuals.com. All Manuals Search And Download.  

JVC Portable CD Player XL PG38SL User Manual
Kalorik Waffle Iron USK WM 30821 User Manual
Kambrook Electric Heater KOH105 User Manual
Kathrein Satellite TV System 9986492 User Manual
Kenwood Car Speaker KFC HQ130 User Manual
Kenwood Car Speaker KFC HQ710 User Manual
Kenwood Food Processor XVP001 User Manual
Kenwood Stereo System KDV C820 User Manual
Kodak Scanner A 61580 User Manual
Kompernass Gas Grill KH 1603 User Manual