42
IN
User’s Guide
English, Deutsch, Español, Français, Italiano, Svensk,
Nederlands, Portugués,
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conform to the following
Agency Approvals
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
UL, CUL, DEMKO-GS
EMC: EN 55022
EN 55024
EN 61000-3-2
Other specific Country Approvals may apply, see please product certification label.
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: IEC 60950-1: 1st Edition
October, 2003
Battery Safety Information
CAUTION: Risk of explosion if the battery in this projector is replaced with the incorrect type of
battery. See page 33 for battery replacement instructions.
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated. InFocus, In Focus, and
INFOCUS (stylized) are either registered trademarks or trademarks of InFocus
Corporation in the United States and other countries.
This user’s guide applies to models IN42, C445, and W400.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Table of Contents
For complete details on connecting and operating the projector, refer to this
User’s Guide. Electronic versions of this User’s Guide in multiple languages
are available on our website.
The website also has technical specifications (an interactive image size cal-
culator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration. See the inside of the back cover for a list of all relevant web
addresses.
Introduction
Included Items
Positioning the projector
4
4
6
Connecting a computer
7
7
9
10
11
12
Required computer connections
Displaying a computer image
Adjusting the image
Connecting a video device
Displaying a video image
Shutting down the projector
Troubleshooting your setup
14
14
Using the keypad buttons
Using the remote control
Using the audio
21
21
22
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
23
23
24
24
Using the menus
Picture menu
25
26
29
Settings menu
Maintenance
33
33
33
34
36
36
Cleaning the lens
Replacing the clock batteries
Replacing the projection lamp
Cleaning the dust filter
Using the security lock
Appendix
37
37
40
Projected image size
RS-232 commands
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Important Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 8 degrees off
axis.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
m
5
8
.
/ 1
’
/ 2
.
4
m
’
5
•
•
Use only approved ceiling mounts.
Use only the power cord provided. A surge-protected power strip is
recommended.
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty booklet.
•
•
Refer to this manual for proper startup and shutdown procedures.
This product has a lamp which contains a very small amount of mer-
cury. Wash hands after cleaning the area and handling the ruptured
lamp. Dispose of it as required by local, state or federal ordinances and
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. When the projector is turned on, keep people, food,
and drinks out of the "keep out" area under and around the projector, as
indicated by the "X" areas below.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Projector components and features: front
Introduction
Your new multimedia projector provides two computer, three video, and
two audio inputs, one audio output, and RS-232 and Network control. It has
XGA 1024x768 resolution. Optional user-changeable short, fixed short, long
and ultra long throw lenses make this a flexible product suitable for many
different uses. The projector is easy to connect, easy to use, and easy to
maintain.
zoom/focus/offset door
remote
control
receiver
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website. Web address information is located on the back inside
cover of this User’s Guide.
air intake
vent
heat vent
elevator foot release
leveling foot
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside back cover for
the web address.
Projector components and features: back
Included Items
lamp door
projector
lens cap*
remote
power cable
VESA computer cable
power switch
power plug
A/V cable
connectors
documentation
*the lens cap tether can attach the lens cap to the projector if desired.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Connector Panel
The projector provides three computer and three video connection options:
component video
computer
audio
remote
control
receiver
(IR)
•
•
•
•
•
one M1-DA (DVI with USB)
one VESA computer
VESA computer
RS232
serial control
RJ-45
lock
M1-DA computer
monitor
one component RCA video (Pr, Pb, Y)
one S-video
one composite RCA video
The projector provides computer and video connectors for audio support:
•
•
•
two composite RCA stereo audio (L, R)
one audio out
two audio ins for computer
composite
video
audio in for
video sources
power connector and switch
s-video
The projector also provides the following connectors:
external
speakers
(audio out)
speaker
•
•
•
•
one wired remote
one monitor out
RS-232 serial connector (for serial control)
RJ-45 connector (for networked control)
The RS-232 Command Line Interface (CLI) specifications and commands
are available in the Appendix and on our website. See the back inside cover
of this User’s Guide for website information.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Positioning the projector
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guide-
lines:
Projection angle in 4:3 mode (default)
10 ft high image
9:1
1:1
•
Position the projector on a flat surface at a right angle to the screen. The
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.
9:1
bottom of image
10% below
lens center
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase exten-
sion cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
lens center
1:1
bottom of image
50% below
lens center
•
•
•
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 29. We recom-
mends using an authorized ceiling mount. The Ceiling Mount Kit is
sold separately; visit our website for more information.
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image. For information
about image sizes at different distances, see “Projected image size” on
page 37.
For the standard lens that comes with the projector, the image exits at a
given angle. However, the lens shift feature makes the image offset
variable. The image offset is 90% at a 9:1 ratio when the projector is in
4:3 mode (default mode). This means that if you have an image 10’
high, the bottom of the image will be 1’ below the center of the lens.
•
•
The image offset is 50% when the lens shift is at a 1:1 ratio. This means
that if you have an image 10’ high, the bottom of the image will be 5’
below the center of the lens.
For information about the optional lenses image offsets, see “Projected
image size” on page 37.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Connecting a computer
connect computer cable
Required computer connections
Connect one end of the VESA computer cable to the Computer 2 connector
on the projector. Connect the other end to the video port on your computer.
If you are using a desktop computer, you first need to disconnect the moni-
tor cable from the computer’s video port.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
connect M1-DA cable
connect audio cable
To control your computer’s mouse using an optional remote control, con-
nect the optional M1-DA cable to the USB and DVI ports on your computer,
and connect the other end to the Computer 1 (M1-DA) connector on the
projector.
To have sound with your presentation, connect the audio cable to your com-
puter and to the corresponding computer Audio In connector on the projec-
tor.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the Monitor out connector on the projector.
connect monitor cable
connect RS-232 cable
You can control the projector from an LCD control panel, touch screen, or
other control device or computer by connecting an RS-232 cable to the pro-
jector’s Serial Control connector. Specific RS-232 commands can be found
in the Service and Support section of our website and in the Appendix.
The projector can be managed by networking software through its Network
(RJ-45) connector. Detailed instructions on this feature can be found on our
website.
connect CAT-5 cable
Network
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Displaying a computer image
Remove the lens cap.
remove lens cap
Press the power switch on the back of the projector to the on (I) position.
The Power light on the Status Indicator Panel (page 14) lights green.
press Power switch press Power button
2
Press the Power button on the top of the projector or the remote.
The Power light blinks green and the fans start to run. When the lamp
comes on, the startup screen is displayed and the light is steady green. It can
take a minute for the image to achieve full brightness.
1
? No startup screen? Get help on page 15.
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button on the keypad or remote.
activate laptop’s external port
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your computer’s documenta-
tion to learn your computer’s key combination.
? No computer image? Get help on page 15.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
release
button
adjust height
release
button
Adjusting the image
Adjust the height of the projector, if necessary, by pressing the release but-
tons on each side of the projector’s front to extend the elevator feet.
elevator
foot
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle (perpendicular) to the screen.
See page 37 for a table listing screen sizes and distances.
adjust zoom and focus
Adjust the zoom or focus by rotating the Zoom or Focus rings inside the
lens door until the desired image size and focus are produced.
If the image is not on the screen or viewing area, adjust it by using the lens
shift dials inside the lens door.
adjust lens shift
Use the right dial to shift the lens left or right. Use the left dial to shift the
lens up or down.
adjust Contrast or Brightness
contrast
brightness
Adjust the Contrast or Brightness in the Picture menu.
See page 25 for help with the menus.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Connecting a video device
Standard video connections
connect A/V cable
Plug the audio/video (A/V) cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the yel-
low Video 3 connector on the projector. Plug a white connector into the left
audio out connector on the video device and plug a red connector into the
right audio out connector on the video device. Plug the remaining white
connector into the left audio in connector on the projector, and plug the red
connector into the right audio in connector on the projector.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
NOTE: Always use the power cable that shipped with the projector.
Optional video connections
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the Video 2 connector on the projector. Use the A/V cable’s
audio connectors as described directly above (the yellow connectors on the
A/V cable are not used).
connect S-video and video cables
If the video device uses component cable connectors (sold separately), plug
the cable’s green connectors into the green component-out connector on the
video device and into the Video 1 green component connector (labeled “Y”)
on the projector. Plug the component cable’s blue connectors into the blue
component-out connector on the video device and into the blue component
connector (labeled “Cb/Pb”) on the projector. Plug the component cable’s
red connectors into the red component-out connector on the video device
and into the red component connector (labeled “Cr/Pr”) on the projector.
Use the A/V cable’s audio connectors as described above (the yellow con-
nectors on the A/V cable are not used). NOTE: The component connectors
can be used for HDTV sources (480i, 480p, 720p, 576i and 1080i formats).
connect component cables
and video cables
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Displaying a video image
Remove the lens cap.
remove lens cap
Press the power switch on the back of the projector to the on (I) position.
The Power light on the Status Indicator Panel (page 14) lights green.
press Power switch
press Power button
Press the Power button on the top of the projector or the remote.
2
The Power light blinks green and the fans start to run. When the lamp
comes on, the startup screen is displayed and the light is steady green. It can
take a minute for the image to achieve full brightness.
1
? No startup screen? Get help on page 15.
Plug in and turn on the video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Source button on the keypad or remote.
adjust height
release
button
release
button
Adjust the height of the projector, if necessary, by pressing the release but-
tons on each side of the projector’s front to extend the elevator feet. Rotate
the feet, if necessary, to level the projector.
elevator
foot
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 37 for a table listing screen sizes and distances
to the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Adjust the zoom or focus by rotating the Zoom or Focus rings inside the
lens door until the desired image size and focus are produced.
adjust Zoom and Focus
If the image is not on the screen or viewing area, adjust it by using the lens
shift dials inside the lens door.
adjust Lens Shift
Use the right dial to shift the lens left or right. Use the left dial to shift the
lens up or down.
Adjust the volume in the Audio menu.
adjust volume
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
adjust Picture menu
See page 25 for help with the menus.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Shutting down the projector
The projector automatically blanks the screen after no active source is
detected for 5 minutes. This blank screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or
keypad button is pressed.
Screen Save
Table 1: Status indicator light behavior and meaning
You can make the blank screen appear after five minutes by turning on
Screen Save in the Settings>System menu. See page 30.
Status Indicator Panel icons
Meaning
Power Save
Power, solid green
The power button has been pressed and
the software has initialized or the projec-
tor has been powered off.
The projector also has a Power Save feature that automatically turns the
lamp off after no signals are detected for 20 minutes. After 10 additional
minutes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 30.
Power, blinking green
Thermometer
The power button has been pressed and
the software is initializing, or the projec-
tor is powering down and the fans are
running to cool the lamp.
Turning off the projector
To turn off the projector, press the power button and verify that you want to
turn the projector off by pressing the power button again within 3 seconds.
You can cancel the shutdown by not pressing the power button a second
time. The lamp turns off and the Power light blinks green for over 1 minute
while the fans continue to run to cool the lamp. When the lamp has cooled,
the Power light is solid green and the fans stop. Press the power switch on
the back of the projector and unplug the power cable to completely power
off the projector.
The projector is too hot. Make sure the
vents aren’t blocked (see page 19). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit our website to contact
Service.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Problem
Solution
Result
Plug power cable in, press power switch and
power button. Remove lens cap.
No startup screen
Correct image
3
2
1
Computer image projected
Only startup screen appears
Press the Source button
Activate laptop’s external port
A
A
A
or restart
laptop
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Computer image projected
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating
system)
No computer image, just the words “Signal out of
range”
Signal
range
out
of
A
A
A
You may also need to set a different
resolution on your computer, as shown
in the following problem, “Image fuzzy
or cropped”
Set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab,
select1024x768)
Image clear and not cropped
Image fuzzy or cropped
A
A
A
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Projector troubleshooting
Problem
Solution
Result
Square image
Image not square
Adjust keystone the Picture menu
Correct image
Adjust the focus ring or Sharpness in the
Picture>Advanced menu
Image not sharp
A B
A B
Change aspect ratio to 16:9 in
Picture>Aspect ratio menu
Correct image
Image does not fit 16:9 screen
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Turn on/off Ceiling in Settings>System
menu
Correct image
Image upside down
B
A
A B
Image reversed left to right
Turn on/off Rear in Settings>System menu
Correct image
A
A B
Correct image
Projected colors don’t match source
Adjust color, tint, color temperature,
brightness, contrast in the menus
COLOR
COLOR
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Make sure vents aren’t blocked; allow
projector to cool for one minute
Unplug projector; wait one minute; plug in
projector and turn it on: lamp lights
Lamp won’t turn on, Temp light is lit (page 14)
Temperature light
Lamp may need to be replaced (page 34)
Lamp won’t turn on, Lamp light is lit (page 14)
Lamp turns on
Lamp light
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Correct image
Move projector, adjust zoom or lens shift,
adjust height
Image not centered on screen
Adjust horizontal or vertical position in
Picture>Advanced menu
Still having problems?
If you need assistance, visit our website or call us. See the inside of the back cover for a list of all relevant web addresses.
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its
full value.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Using the keypad buttons
power–turns the projector on (page 9) and off (page 14).
menu–opens the on-screen menus (page 25).
up/down arrows–navigates to and adjusts settings in the menus (page 25).
select–confirms choices made in the menus (page 25).
source–switches among active sources
Using the remote control
The remote uses two (2) AA batteries. They are easily installed by sliding
the cover off the remote's back, aligning the + and - ends of the batteries,
sliding them into place, and then replacing the cover.
navigation
buttons
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 15 feet (4.5m).
For best results, aim the remote directly at the projector.
Press the remote's Menu button to open the projector's menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus.
Press the remote’s Power button to turn the projector on and off.
The remote also has a Source button to switch between sources.
Troubleshooting the remote
•
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Make sure you’re pointing the remote at the projector, not the com-
puter, and are within the remote range of 15 feet (4.5m).
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Using the audio
connect audio cable
To play sound from the projector, connect your source to the Audio In con-
nector on the projector.
To adjust the volume, mute, or loudness, use the Audio menu (see page 29).
Troubleshooting audio
If there is no sound, check the following:
•
•
•
•
Make sure the audio cable is connected.
Make sure mute isn’t active.
adjust volume
Make sure the volume is turned up enough.
Make sure you are connected to the corresponding audio in for your
source. Audio 1 corresponds to Computer 1, Audio 2 corresponds to
Computer 2, Audio 3 corresponds to Video 2 and 3, and Audio 4 cor-
responds to Video 1.
•
•
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
Connecting external speakers
The projector can be attached to external speakers that have their own
power source by plugging a speaker cable into the projector’s Audio Out
connector.
external speakers
speaker
cable
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For gen-
eral information on using the menus, see page 25.
Several features are provided to make giving presentation easier. The fol-
lowing is an overview, details are found in the menu section on page 25.
•
The Custom key, available on several optional remotes only, allows
you to assign various features to the key. The default effect is Source
Info. You can select from Blank, Mute, Aspect Ratio, Source, Auto
Image, Freeze, Magnify, Source Info, and Service Info. See page 31 for
details.
•
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 26 for details.
•
•
•
•
The Freeze effect allows you to freeze the displayed image. This is use-
ful if you want to make changes on your computer without your audi-
ence seeing them.
•
•
Adjust the Color Temperature in the Advanced menu.
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
The Startup Logo menu option lets you change the default startup
screen to a black, white, blue, or a custom logo screen via Capture New.
See page 30.
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later. See page 27.
Two menu options, Power Save and Screen Save, are provided to auto-
matically shut down the projector after several minutes of inactivity or
display a blank screen. This helps preserve lamp life. See page 30.
A Low Power menu option is also available to help lower the projec-
tor’s fan sound volume. See page 29.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Optimizing video images
Customizing the projector
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 25.
You can customize the projector for your specific setup and needs. See
page 29 to page 33 for details on these features.
•
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 26.
For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu.
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 26.
•
Specify which source the projector checks first for an active signal dur-
ing power-up.
•
•
•
•
•
•
Turn the projector’s on-screen display messages on and off.
Turn on power saving features.
•
•
Select a Sharpness setting. See page 28.
Specify blank screen colors and startup logos.
Specify the menu language.
Adjust the Color Temperature. Select a listed value, or select User and
individually adjust the intensity of the red, green, and blue color. See
page 28.
Control your projector using RS232 commands. See page 8 and page 40.
Customize the projector for your specific installation using optional
long or short throw lenses. See the inside back cover of this User’s
Guide for ordering information.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Using the menus
To open the menus, press the menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous, then press Select to go to
the previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Main menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
Dots
The menus are grouped by usage:
•
•
The Picture menu provides image adjustments.
The Settings menu provides set-up type adjustments that are not
changed often.
•
The Source Info menu provides a read-only display of information
about the projector and source.
Settings
menu
Picture
menu
Certain menu items may be grayed out until a particular source is con-
nected. For example, Tint is only available for video sources and will be hid-
den when a computer source is active. Other menu items may be grayed out
when they are not available. For example, Brightness is grayed out until an
image is active.
Source Info menu
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Picture menu
To adjust the following six settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
Keystone Vertical
increasing keystone
decreasing keystone
Keystone Vertical: adjusts the image vertically and makes a squarer image
by using an adjustable scale band.
Keystone Horizontal: adjusts the image horizontally and makes a squarer
image by using an adjustable scale band.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Keystone Horizontal
Brightness: changes the intensity of the image.
Color: (video sources only) adjusts a video image from black and white to
fully saturated color.
Tint: (video sources only) adjusts the red-green color balance in the image.
Auto Image: resynchs the projector to the source.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or
down to fill the display area.
Aspect Ratio
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Presets: The provided Presets optimize the projector for displaying com-
puter presentations, photographs, film images, and video images. (Film
input is material originally captured on a film camera, like a movie; video
input is material originally captured on a video camera, like a TV show or
sporting event.)
Save Settings
There are also user-definable presets. To set a preset for the current source,
adjust the image, select Save Settings in the Presets menu, then select Save
User Presets 1 (or 2 or 3). You can recall these settings in the future by select-
ing the User 1 preset. If you select User Presets then further adjust the
image, Presets Off will automatically be selected in the Preset menu to indi-
cate changes have been made.
To restore the factory default settings, choose Factory Reset in the Set-
tings>Service menu.
Presets
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Advanced settings
Sharpness: changes the clarity of the edges of a video image. Select a sharp-
ness setting.
Color Space: This option applies to computer and component video
sources (except 480i/576i). It allows you to select a color space that has been
specifically tuned for the input signal. When Auto is selected, the projector
automatically determines the standard. To choose a different setting, turn
off Auto, then choose RGB for computer sources, choose either SMPTE240,
REC709 or REC601 for component video sources.
Sharpness
Color Temperature: changes the intensity of the colors. Select a listed
value, or select User and individually adjust the intensity of the red, green,
and blue colors.
Color Space
Video Standard: when set to Auto, the projector attempts to automatically
pick the video standard based on the input signal it receives. (The video
standard options may vary depending on your region of the world.) If the
projector is unable to detect the correct standard, the colors may not look
right or the image may appear “torn.” If this happens, manually select a
video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu.
Color Temperature
Active Iris: when on, the projector monitors the image brightness and mod-
ifies the light output if the image is dark, which improves black levels. In
Presentation mode, it looks at peak brightness, in Theater mode it looks at
average brightness.
Overscan: (video sources only) removes noise around the video image.
The following 4 options are for computer sources only (except M1-D signal):
Phase: adjusts the horizontal phase of a computer source.
Video Standard
Tracking: adjusts the horizontal scan of a computer source.
Active Iris
Horizontal / Vertical Position: adjusts the position of a computer source.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Settings menu
Audio: allows adjustments to the Volume. Also allows you to turn on and
off the Internal speakers, and projector startup Chime.
Settings
menu
Sources: allows you to assign a particular input to a specific source key
when using the Integrator remote. Also allows selection of a default Startup
Source and enables or disables Autosource.
Audio
Sources>Power-up Source: this determines which source the projector
checks first for active signal during power-up.
Sources>Autosource: When Autosource is not checked, the projector
defaults to the source selected in Powerup Source. If no source is found, a
blank screen displays. When Autosource is checked, Powerup Source deter-
mines which source the projector defaults to at power-up. If no signal is
present, the projector checks the sources in order until a source is found or
until power down.
System>Rear: reverses the image so you can project from behind a
translucent screen.
Powerup
Source
Sources
Ceiling: turns the image upside down for ceiling-mounted projection.
IR Receivers: turns individual IR receivers off or on to avoid environ-
mental interference.
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on. This allows
control of ceiling mounted projectors with a wall power switch.
Display Messages: displays status messages (such as “Searching”) in the
lower-left corner of the screen.
Low Power: toggles between on and off. Turn it on to lower the light out-
put of the lamp. This also lowers the fan speed, making the projector qui-
eter.
IR Receivers
PC Screen Saver Off: prevents your notebook computer from going into
Screen Save mode. The projector must be connected to the PC via a USB
cable for this feature to work.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Power Save: automatically turns the lamp off after no signals are
detected for 20 minutes. After 10 additional minutes with no signal, the
projector powers down. If an active signal is received before the projec-
tor powers down, the image will be displayed.
Screen Save
Screen Save: automatically blanks the screen after no signals are
detected for five minutes. The image returns when an active source is
detected or a remote or keypad button is pressed. Screen Save is disabled
when Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen at startup and when no source is detected. It
also allows you to capture and display a custom startup screen (except
from an M1-D source).
To capture a custom logo, display the image you want to capture on your
computer and select the Capture New option. From the Capture New
menu, use the Capture Position X and Capture Position Y adjustments to
frame the logo to be captured. Press Capture Start in the Capture New
menu. The projector will let you know if the capture was a success or a
failure.
Capture New
Startup Logo
The next time you start the projector, the custom logo you captured dis-
plays.
Blank Screen
Blank Screen: determines what color is displayed when you press the
Blank button on an optional remote.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Custom Key (for use with optional remote only): allows you to assign a dif-
ferent function to the Custom key on the optional remote to quickly and
easily use the effect. Only one effect can be enabled at a time. The default is
Source Info; highlight an effect and press Select to choose a different one.
Custom Key
Blank: shows an empty screen.
Mute: turns off all sound.
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes computer sources to be reacquired.
Freeze: pauses the projected image.
Magnify: allows you to enlarge a section of the projected image.
Source Info: displays the Source Info menu.
Service Info: displays the Service Info menu.
Network: The projector has an RJ45 Ethernet connector that supports net-
work connections and TCP/IP protocols. This will allow for the control and
management of the projector over a corporate network. Visit our website for
complete details on using the networking functionality. The following fields
are accessible when DHCP is not checked and available for manual entry of
data.
Network
Info
Network
IP Address: Identifies the projector on the network.
Subnet Mask: Separates the network address part of the IP address.
Default Gateway: The IP address of the local router.
DHCP: Select this to automatically obtain an IP address, Subnet mask,
and Default gateway.
Network Info: Provides information on the network configuration.
The Network Info menu is informational and cannot be edited. It displays
the current IP Address, Subnet Mask, Default Gateway, and the projector’s
MAC Address.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Language: allows you to select a language for the onscreen display of
menus and messages.
Language
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp and Filter Hours and Net-
work settings) to their default after displaying a confirmation dialog box.
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu
to zero. Do this only after changing the lamp. It displays a confirmation dia-
log box.
Lens Type
Service menu
Reset Filter Hours: resets the filter counter in the Service Info menu to
zero. Do this only after cleaning the filter. It displays a confirmation dialog
box.
Lens Type: change this setting only if you purchase an optional lens. The
projector customizes its keystone settings based on the lens used. Select
your optional lens from the menu. A sticker containing a number between 1
and 5 is attached to the lens to help you identify which type of lens you pur-
chased.
Service Info: provides information for service.
Service Code: only used by authorized service personnel.
Service Info
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Maintenance
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
turn off and unplug
the projector
Replacing the clock batteries
The projector has a lithium Hitachi Maxell battery (part number CR2032) on
the bottom that is used to power the clock used for networking applications.
Visit our website for complete details on using the networking functionality.
wait 45 minutes
1 Turn off the projector and unplug the power cable.
open battery cover
2 Wait 45 minutes to allow the projector to cool thoroughly.
3 Turn the projector upside down and use a coin to turn the battery cover
12'0
to the “Open” position.
4 Remove the battery and dispose of in an environmentally proper man-
ner.
5 Install a new battery with the “+” side facing up.
%.15'
6 Press the battery into place, then replace the battery cover.
install new battery,
+ side up
NOTE: The clock time will need to be reset in the web browser application
after replacing the battery.
press battery into position
close battery cover
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Replacing the projection lamp
The lamp hour timer in the Service Info menu counts the number of hours
the lamp has been in use. Twenty hours before the specified end of the
lamp’s life, the message “Change lamp” briefly appears on the projected
screen.
Service Info menu
areas), your retailer or your dealer. Use only a replacement lamp with the
same type and rating as the original lamp.
turn off and unplug
the projector
The part number is SP-LAMP-027.
1 Turn off the projector and unplug the power cable.
wait 45 minutes
2 Wait 45 minutes to allow the projector to cool thoroughly.
3 Loosen the lamp cover screw on the right side of the projector (marked
by the arrow) then slide and lift the lamp cover off.
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 45 minutes before
you replace the lamp.
•
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
lamp cover screw
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the bulb ruptures, small glass fragments may be generated.
The lamp housing is designed to contain these fragments, but use cau-
tion when removing the lamp housing. Before replacing the lamp, clean
the lamp compartment and dispose of cleaning materials. Wash hands
after lamp replacement. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or fed-
eral ordinances and regulations. For more information see
Download from Www.Somanuals.com. All Manuals Search And Download.
34
4 Loosen the three captive screws (marked by the arrows) on the lamp
module.
loosen the captive screws on lamp module
5 Carefully remove the lamp module by grasping and lifting the handle.
Dispose of the lamp in an environmentally proper manner.
lamp module handle
6 Install the new lamp module, making sure that it is properly seated, and
tighten the three captive screws.
7 Replace the cover over the lamp module by sliding it back into place and
tightening the screw.
8 Plug in the power cable, press the power switch then press the Power
button to turn the projector back on. Reset the lamp hour timer by navi-
gating to the Settings>Service menu and selecting Reset Lamp Hours.
reset lamp hours in Service menu
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Cleaning the dust filter
1 Turn off the projector and unplug the power cable.
2 Wait 45 minutes to allow the projector to cool thoroughly.
WARNING: To avoid burns, allow the projector to cool for at least 45
minutes before you clean or replace the dust filter.
wait 45 minutes
3 Remove the dust filter cover on the side of the projector by pressing up
on the two tabs at the cover’s bottom.
4 Pull the tab on the center of the black dust filter bracket and lift it off.
5 Clean the filter, cover, and vent using a vacuum set on low power.
Replace the filter if it is damaged or too dirty to clean.
6 Replace the dust filter and the bracket on the cover, then replace the dust
filter cover.
7 Reset the filter hour timer by navigating to the Settings>Service menu
and selecting Reset Filter Hours.
dust filter cover
tabs
reset filter hours in Service menu
Using the security lock
The projector has a security lock for use with a cable lock system. See the
Accessories catalog that came with the projector, or visit our website, for
ordering information. Refer to the information that came with the lock for
instructions on how to use it.
security lock
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Table 3: Projection sizes: Short Fixed lens (0.8:1 throw ratio)
Appendix
Projection Distance
(inch/m)
Projected image size
NOTE: Visit the Service section of our website for interactive image size cal-
culators for the standard and optional lenses.
Screen Size (inch/m)
40/1
Minimum
24/0.6
Table 2: Projection sizes: Standard lens (1.5 - 1.8:1 throw ratio)
60/1.5
35/0.9
Minimum Image
Maximum Image
70/1.8
43/1.1
Diagonal
Image
(feet/m)
Image
Width
(feet/m)
Diagonal
Image
(feet/m)
Image
Width
(feet/m)
Distance
(feet/m)
100/2.5
63/1.6
120/3
75/1.9
Min Distance
2.1/0.66
1.7/0.53
2.6/0.79
2.1/0.63
3/0.9
150/3.8
94/2.4
5/1.5
3.5/1.1
7.0/2.1
2.8/0.86
5.6
4.2/1.3
1.7
3.4/1.0
8.3/2.5
10/3
200/5.1
130/3.3
161/4.1
193/4.9
224/5.7
10/3.0
15/4.6
20/6.1
25/7.6
250/6.4
10.4/3.2
13.8/4.2
17.2/7.6
20.6/6.3
8.3/2.5
11/3.4
13.8/4.2
16.5/5
12.5/3.8
16.6/5.1
20.7/6.3
24.8/7.6
300/7.6
13.3/4
16.6/5
19.8/6.1
350/8.9
Max Distance
30/9.1
The image offset range for the standard lens is 9:1 (90%) to 1:1 (50%).
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Table 4: Projection sizes: Short Zoom lens (1.2 -2.0:1 throw ratio range)
Projection Distance (inch/m)
Table 5: Projection sizes: Long Throw lens (1.9 - 3.9:1 throw ratio range
Projection Distance (inch/m)
Screen Size
(inch/m)
Screen Size
(inch/m)
Minimum
39/1.0
Maximum
63/1.6
Minimum
59/1.5
Maximum
122/3.1
40/1
60/1.5
40/1
60/1.5
59/1.5
94/2.4
94/2.4
185/4.7
70/1.8
67/1.7
110/2.8
157/4.0
189/4.8
240/6.1
319/8.1
402/10.2
480/12.2
559/14.2
70/1.8
110/2.8
157/4.0
189/4.8
236/6.0
319/8.1
402/12.2
480/16.3
642/20.4
803/20.4
217/5.5
100/2.5
120/3
98/2.5
100/2.5
120/3
311/7.9
118/3.0
150/3.8
197/5.0
248/6.3
299/7.6
350/8.9
374/9.5
150/3.8
200/5.1
250/6.4
300/7.6
350/8.9
150/3.8
200/5.1
250/6.4
300/7.6
400/10.2
500/12.7
467/11.9
630/16.0
787/23.9
94532.0
126040.1
1579/40.1
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Table 6: Projection sizes: Ultra Long Throw lens (3.9 - 7.4:1 throw ratio
range
Projection Distance (inch/m)
Screen Size
(inch/m)
40/1
Minimum
122/3.1
Maximum
236/6.0
60/1.5
70/1.8
189/4.8
354/9.0
220/5.6
513/10.5
594/15.1
717/18.2
898/22.8
1197/30.4
1496/45.6
1795/53.3
2398/60.9
3000/76.2
100/2.5
120/3
315/8.0
382/9.7
150/3.8
200/5.1
250/6.4
300/7.6
400/10.2
500/12.7
476/12.1
638/16.2
799/24.4
961/28.5
1283/32.6
1602/40.7
Download from Www.Somanuals.com. All Manuals Search And Download.
39
A read command returns the range and the current setting, for example:
RS-232 commands
Communication Configuration
Visit our website for additional RS-232 settings and information.
Read Command Examples
Function
Brightness
Volume
Command
(BRT?)
Response
(96-160,128)
(0-32, 0)
To control this projector via RS-232, connect a null modem cable and set the
control system serial port settings to match the following communication
configuration:
(VOL?)
RS-232 Port Settings
Lamp Hours
(LMP?)
(0-65534, 42)
Setting
Value
19,200
8
A write request example:
(AAA####) where
Bits per second
Data bits
(starts the command
Parity
None
1
AAA denotes the command
#### denotes the value to be written
(leading zeros not necessary)
) ends the command
Stop bits
Flow control
Emulation
None
VT100
Some commands have ranges, while others are absolute. If a number greater
than the maximum range is received, it is automatically set to the maximum
number for that function. If a command is received that is not understood, a
"?" is returned. With absolute settings, "0" is off, 1-9999 is on. The one excep-
tion is the Power command, where 0 is off and 1 is on.
Command Format
All commands consist of 3 alpha characters followed by a request, all
enclosed in parentheses. The request can be a read request (indicated by a
"?") or a write request (indicated by 1 to 4 ASCII digits).
A read request example:
(AAA?) where
To assure the projector can process a command, wait 3 seconds before enter-
ing the next command.
( starts the command
AAA denotes the command
? denotes the read request
) ends the command
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Write Command Examples
St
e
p
Com-
mand
Function
Min Max
De-fault
Function
Brightness
Power
Command
(BRT140)
(PWRO)
(PWR1)
Response
Sets the brightness to 140
Turns power off
About (Source Info)
0: n/a
1: enable
ABT at W
0
0
1
2
n/a
Power
Turns power on
Active Iris
0: Off
1: Presentation
2: Film
IRI at RW
1
2
Error Conditions
Not all commands are supported for all projectors. If an unsupported com-
mand is issued, the command will be ignored. If a command is received that
is not understood, a ‘?’ character will be returned indicating the command
was not understood.
Aspect Ratio
0: Native
1: 16:9
ARZ at RW
0
2
Limitations
2: 4:3
The projector cannot respond to commands coming in at a high-rate. There-
fore, a delay must occur between commands to ensure that the command
gets properly executed. To assure the projector can process a command,
wait 3 seconds before entering the next command.
Auto Image
0: n/a
1: enable
AIM at W
0
0
0
0
1
1
1
1
n/a
0
Auto Power
0: disable
1: enable
APO at RW
ASC at RW
BLK at RW
The Step column refers to increasing or decreasing the menu bar position
since the On-screen Display is not an exact match of values. For example,
Step 2 changes the data by 2 through the CLI (Command Line Interface).
The menu bar is up (or down) by 1.
Auto Source
0: disable
1: enable
1
Blank
0: off
1: on
0
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Blank Screen
0: black
BSC at RW
0
2
1
Custom Key (Effect)
0: blank
EFK at RW
0
8
7
1: blue
1: mute
2: white
2: aspect ratio
3: source
4: auto image
5: freeze
6: zoom
7: Source Info
8: Service Info
Blue Gain
Brightness
BCG at RW
BRT at RW
CEL at RW
64
96
0
192
160
1
128
128
0
1
1
Ceiling
0: disable
1: enable
Display Messages
0: disable
1: enable
DMG at RW
RST at W
0
0
0
1
1
1
1
Chime
0: disable
1: enable
ACE at RW
0
1
1
Factory Reset
0: not reset
1: reset
n/a
0
Color
CLR at RW
CSM at RW
96
0
160
7
128
7
1
Color Space
0: RGB
1: SMPTE240
2: REC709
3: REC601
7: Auto
Freeze
0: disable
1: enable
FRZ at RW
Green Gain
GCG at RW
DKH at RW
HPS at RW
64
38
192
218
128
128
1
1
1
Horizontal Keystone
Horizontal Position
Color Temp
0: 9300K
1: 6500K
2: 7200K
3: User
TMP at RW
0
3
2 (computer)
1 (video)
def:-
128
def:+1 auto
28
Internal Sound Enable INT at RW
0
1
1
0: disable
1: enable
Contrast
CON at RW 96
160
128
1
IR Receiver front
0: disable
IRF at RW
0
1
1
1: enable
Download from Www.Somanuals.com. All Manuals Search And Download.
42
IR Receiver rear
0: disable
1: enable
IRR at RW
IRT at RW
LAN at RW
0
0
0
1
1
0
0
Time In Hours Last
Bulb2 Lasted
LB2 at R
LB3 at R
LPE at RW
0
0
0
32766
32766
1
0
0
0
Time In Hours Last
Bulb3 Lasted
IR Receiver top
0: disable
1: enable
1
Low Power
0: disable
1: enable
Language
11
0 = English
1 = French
2 = German
3 = Spanish
7 = Portuguese
10 = Simplified
Chinese
Magnify
MAG at RW
MGE at RW
0
0
48
1
0
0
1
Magnify Enable
0: disable
1: enable
Magnify Position Hor- MPH at RW
izontal
128
96
0
896
672
1
512
384
0
1
1
11 = Italian
12 = Swedish
Magnify Position Ver-
tical
MPV at RW
Lamp Hours
LMP at R
LML at R
0
0
32766
1
0
1
Lamp Lit
0: not lit
1: lit
Menu
0: disable
1: enable
MNU at RW
Reset Lamp Hours
0: not reset
1: reset
LRT at W
0
1
n/a
Menu Navigation
0: up
1: down
NAV at W
0
0
4
1
n/a
0
4: select
Number of Lamp
Resets
LMR at R
LMT at R
LB1 at R
0
0
0
32766
0
0
0
Mute
0: disable
1: enable
MTE at RW
Lamp Total On Time
(All Bulbs)
21474
83646
Time In Hours Last
Bulb1 Lasted
32766
Download from Www.Somanuals.com. All Manuals Search And Download.
43
NND (PC Screen
Saver Off)
0: disable
NND at RW
OVS at RW
0
0
1
1
1
0
Rear
0: disable
1: enable
REA at RW
0
1
0
1: enable
Red Gain
RCG at RW
FRT at W
64
0
192
1
128
n/a
1
Overscan
0: disable
1: enable
Reset Filter Hours
0: not reset
1: reset
Phase
MSS at RW
0
0
26
1
0
0
1
Save User Presets 1
0: not saved
1: saved
US1 at W
US2 at W
US3 at W
SSV at RW
0
0
0
0
1
1
1
5
n/a
n/a
n/a
0
Power
0: disable
1: enable
PWR at RW
Save User Presets 2
0: not saved
1: saved
Power Save
0: disable
1: enable
PSV at RW
DSC at RW
0
0
1
4
0
0
Save User Presets 3
0: not saved
1: saved
Power-up Source
0: computer 1
1: computer 2
2: video 1
Screen Save
0: 5 minutes
1: 10 minutes
2: 15 minutes
3: 20 minutes
4: 25 minutes
5: 30 minutes
3: video 2
4: video 3
Presets
PST at RW
0
12
c: 0
v: 2
0: presentation
1: photography
2: film
Sharpness
SHP at RW
5
9
7 (computer
and video 1)
6 (video 2
and 3)
3: video
5 = Sharpest
6 = Sharper
7 = Standard
8 = Softer
9: Presets Off
10: user 1
11: user 2
12: user 3
9 = Softest
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Source
SRC at RW
SR1 at RW
SR2 at RW
SR3 at RW
SR4 at RW
0
0
0
0
0
4
4
4
4
4
0
0
1
2
3
Startup Logo
0: blank screen
1: default
DSU at RW
0
2
1
0: computer1
1: computer2
2: video 1
3: video 2
4: video 3
2: captured
Tint
TNT at RW
MTS at RW
96
160
128
1
1
Source 1
Tracking
def:
-128
def:
+128
auto
0: computer 1
1: computer 2
2: video 1
3: video 2
4: video 3
Unit Total Time On
ONL at R
0
21474
83646
0
Source 2
0: computer 1
1: computer 2
2: video 1
3: video 2
4: video 3
Vertical Keystone
Vertical Position
DKC at RW
VPS at RW
38
218
128
1
1
if
if
auto
def<
128:
0
else:
def -
128
def<1
28:def
x2
else:d
ef
Source 3
0: computer 1
1: computer 2
2: video 1
3: video 2
4: video 3
+128
Video Standard
0: Auto
1: NTSC
2: PAL
VSU at RW
VOL at RW
0
3
0
Source 4
0: computer 1
1: computer 2
2: video 1
3: video 2
4: video 3
3: SECAM
Volume
0
32
16
1
Download from Www.Somanuals.com. All Manuals Search And Download.
45
INDEX
D
Default gateway 31
DHCP 31
A
Aspect Ratio 31
audio 22
Display Messages 29
displaying
Audio In connector 7, 11
Auto Image 31
Auto Power 29
Autosource 29
computer image 9
video images 12
dust filter, cleaning 36
E
B
elevator foot 10, 12
Blank 31
Brightness 10
F
Factory Reset 32
filter, resetting hours 32
focus 10, 13
C
Capture Position 30
Capture Start 30
Freeze 31
cleaning the dust filter 36
cleaning the lens 33
clock batteries 33
Color 13
fuzzy image 16
H
HDTV sources 11
colors are incorrect 18
component cable connector 11
computer connections
optional 7
required 7
computer image
I
image
display computer 9
display video 12
size 6
displaying 9
optimize 23
image does not fit screen 17
image not centered 20
image not sharp 17
image not square 17
image reversed 18
image size matrix 37
image upside down 18
IP Address 31
connector panel 5
contacting service 20
Contrast 10, 13
custom logo startup screen 30
customer service contact information 20
IR Receivers 29
Download from Www.Somanuals.com. All Manuals Search And Download.
46
L
P
lamp hours, resetting 35
lamp replacement 34
lamp won’t turn on 19
Language 32
PC Screen Saver Off 29
Picture menu 26
power cable 7, 11
Power Save 30
laptop
Power-up Source 29
presentation features 23
projection distance 6
projector
connecting 7
external video port 9
lens, cleaning 33
Low Power 29
connector panel 5
customizing 24
height 10, 12
M
Magnify 31
positioning 6, 10, 12
setting up 6
shutdown 14
Main menu 25
menu system 25
Monitor connector 8
mouse, using your 7
Mute 31
troubleshooting problems 14
R
Rear 29
N
remote control 21
replacing the clock batteries 33
replacing the lamp 34
Reset Filter Hours 32
resetting lamp hours 35
RS-232
Network 31
Network connector 8
Network Info 31
no computer image 16
no startup screen 15
cable 8
O
connecting 5
only startup screen appears 15
Overscan 28
Download from Www.Somanuals.com. All Manuals Search And Download.
47
S
V
screen saver, turning off 29
security lock 36
serial connection 5, 8
Service 32
Service Code 32
Service Info 32
Settings menu 29
shutting down projector 14
Source 31
Source troubleshooting 15
Sources 29
video connections
optional 11
standard 11
Video connector 11
video image
displaying 12
video images
optimizing 24
Video Standard 28
volume adjustment 13
Subnet mask 31
S-video connector 11
W
warranty 20
T
X
Tint 13
XGA 4
troubleshooting 14, 15
Z
zoom 10, 13
Download from Www.Somanuals.com. All Manuals Search And Download.
48
|