Regulatory models: W3902, W3904
Download from Www.Somanuals.com. All Manuals Search And Download.
010-0728-02
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
2
•
•
Refer all service to qualified service personnel. Servicing your own
projector can be dangerous to you and will void the warranty.
Important Operating Considerations for Safety
•
•
•
Refer to this guide for proper startup and shutdown procedures.
Follow all warnings and cautions in this manual and on the projector.
Only use replacement parts specified by InFocus. Unauthorized
substitutions may result in fire, electrical shock, or injury, and may
void the warranty
Place the projector in a horizontal position no greater than 15 degrees
off axis.
•
Only genuine InFocus lamps are tested for use in this projector. Use of
non InFocus lamps may cause electrical shock and fire, and may void
the projector warranty.
•
•
Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
Do not block ventilation openings. Locate the projector in a well-
ventilated area without obstructions to intake or exhaust vents. Do not
place the projector on a tablecloth or other soft covering that may block
the vents.
•
•
Hg – Lamp contains mercury. Manage in accordance with local
The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
•
Do not place the projector in direct sunlight, humid, greasy or dusty
places or in places where the projector may come into contact with
smoke or steam.
•
•
•
Do not look directly into the lens while the projector is being used.
Do not drop the projector.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Keep people, food, and drinks out of the "keep out"
area under and around the projector, as indicated by the "X" areas
below.
Do not spill liquid on the projector. Spilled liquid may damage the
projector.
•
Use the power cord provided. Connect the power cord to a receptacle
with a protective safety (earth) ground terminal. A surge-protected
power strip is recommended.
•
•
•
•
Do not overload wall outlets.
When disconnecting the power cord, hold the plug, not the cord.
Wash hands after handling the cables supplied with this product.
m
5
.
8
’
/ 2
.
4
/ 1
m
’
5
The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in
accordance with local disposal laws.
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet.
•
•
Use an InFocus approved ceiling mount kit for proper fitting,
ventilation and installation. The warranty does not cover any damage
caused by use of non-approved ceiling mount kits or by installing in an
improper location.
When the projector is ceiling mounted, wear protective eyewear to
prevent eye injury before opening lamp door.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Introduction
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing too. The IN3902LB has
native XGA 1024x768 resolution, and the IN3904LB has WXGA 1280x800
resolution. This guide applies to all products. They are compatible with a
wide variety of computers and video devices.
zoom (rear ring)
touch keypad
focus (front ring)
Product specifications
To read the latest specifications on your multimedia projector, be sure to
remote control
receiver (IR)
Accessories
The standard accessories that came with your projector are listed in the
included Quick Start Poster/Booklet. Optional accessories can be found on
lens
elevator foot
Online registration
activate your warranty and receive product updates, announcements, and
registration incentives.
power cord
connector
remote control
receiver (IR)
connector
panel
leveling foot
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Connector panel
The projector provides both computer and video connection options,
including:
composite
video
•
•
•
•
•
•
VGA computer (2)
monitor out
HDMI
HDMI
audio in
S-video
computer
S-video
Composite video
Separate assignable audio inputs for video and computer
composite
s-video
VGA 1
VGA
2
VGA 1/2
composite s-video
USB DisplayLink connector, for computer audio/video input. This
USB connection also provides slide advance (and mouse control when
used with an optional remote control only)
The projector also provides the following connectors:
•
Monitor out, to provide an image on your desktop computer as well as
on the projection screen
DisplayLink
connector
audio out
RJ-45
5 volt
output
•
•
•
•
•
LAN port for network control and web server.
LitePort, for connecting a USB flash drive containing images.
Audio out, to provide sound for external speakers
A 5 volt DC output (see below)
security lock
RS232
LitePort
reset
RS-232 connector for serial control. The Command Line Interface (CLI)
specifications and commands are on our website.
NOTE: DisplayLink video and audio is not sent to monitor out and audio
out.
5 volt DC output
The coaxial 6.4mm x 2.2mm jack provides a constant 5 volt, 2 amp DC
output when the projector is on, and will also provide power when the
projector is in standby (powered off) if Network and DisplayLink items in
the Always-On Functions submenu are set to Yes. It is designed to provide
power for an InFocus LiteShow II wireless device, which allows wireless
projection. More information can be found on our website at
www.infocus.com or at your retailer or dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Positioning the projector
(IN3902LB)
(IN3904LB)
10 ft high image
10 ft high image
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general
guidelines:
Projection angle
Projection angle
bottom of image
1.5 ft above center
of lens
bottom of image
1.24 ft above center
of lens
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
lens center
lens center
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase
extension cables). To ensure adequate cable access, do not place the
projector within 6 inches (.15m) of a wall or other object.
Table 1: (IN3902LB)
Range of distance to the screen for a given screen size
•
If you are installing the projector on the ceiling, we strongly
recommend using InFocus approved ceiling mounts for proper fitting,
ventilation and installation. Refer to the installation guide that comes
with the InFocus Ceiling Mount Kit (p/n SP-CEIL-UNIV) for more
information. The warranty does not cover any damage caused by use of
non-approved ceiling mount kits or by installing in an improper
location.
Distance to screen
Diagonal Screen
Size (inches/m)
Minimum distance
(feet/m)
Maximum
Distance (feet/m)
60/1.5
80/2.0
90/2.3
150/3.8
7’ 10”/2.4
10’ 5”/3.2
11’ 8”/3.6
19’ 6”/5.9
8’ 7”/2.6
•
•
Position the projector the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
11’ 6”/3.5
12’ 11”/3.9
21’ 6”/6.6
The image exits the projector at a given angle. IN3902LB image offset is
115%; IN3904LB image offset is 112.4%. This means that if you have an
image 10’ high, the bottom of the image will be 1.5' (IN3902LB) and
1.24' (IN3904LB) above the center of the lens.
Table 2: (IN3904LB)
Range of distance to the screen for a given screen size
Distance to screen
Diagonal Screen
Size (inches/m)
Minimumdistance
(feet/m)
Maximum
Distance (feet/m)
60/1.5
80/2.0
90/2.3
150/3.8
6’ 6”/2.0
8’ 8”/2.7
9’ 10”/3.0
16’ 4”/5.0
7’ 4”/2.2
9’ 8”/2.9
10’ 11”/3.3
18’ 1”/5.5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Connecting a computer source
DisplayLink or VGA
connect USB cable
If you have a Windows or Macintosh computer, connect the USB cable
between your computer's USB port and the projector's DisplayLink
connector*. Then to begin installation of the DisplayLink software:
Windows: Follow the instructions on the screen.
MOLEX
MOLEX
Macintosh: A folder will open containing a file named DisplayLink
Installer.pkg. Open that file and follow the instructions on the screen.
* For detailed DisplayLink instructions and troubleshooting, and to
download the latest DisplayLink software, go to
connect computer cable
Or, connect one end of the provided computer cable to the VGA 1 or VGA 2
connector on the projector and the other to the VGA connector on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first (you can connect this
monitor cable to the Monitor Out connector on the projector, see below).
Connect the black power cord to the Power connector on the side of the
projector and to your electrical outlet. The Power light on the Status
connect power cord
NOTE: Always use the power cord that shipped with the projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In Computer connector on the
projector. You may also need an adapter.
connect audio cable
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
NOTE: Only VGA video is sent to the Monitor out connector.
To display a presentation from a USB flash drive, see the Using LitePort
and eliminates the need for a computer source and can be integrated with
common wall plates and conference room input/output panels.
connect monitor cable
To advance slides in a PowerPoint presentation using the remote control,
plug the USB cable between the projector's DisplayLink connector and your
computer. Then press the up and down arrow buttons on the remote control
to move through your slides.
You can control the projector from an LCD control panel, touch screen, or
other control device or computer by connecting an RS-232 cable to the
projector’s Serial Control connector. Specific RS-232 commands can be
found in the Service and Support section of our website.
connect RS-232 cable
The projector can be managed by networking software through its Network
(RJ-45) connector. Detailed instructions on this feature can be found on our
website.
connect CAT-5 cable
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Displaying an image
Touch the Power button.
press Power button
The Power button blinks green and the fans start to run. When the lamp
comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop's documentation for
more information about your laptop's key combination or go to the InFocus
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the keypad.
? Is your laptop connected to the projector's DisplayLink connector? See the
InFocus DisplayLink Software User's Guide (available on the InFocus
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
adjust height
release button
elevator foot
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the side of the
projector.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See the table listing screen sizes and distances on page 6.
Adjust the zoom or focus.
adjust zoom or focus
focus (front ring)
zoom (rear ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Basic Picture menu (on page 32).
For Aspect Ratio, keep in mind that DVD players must be configured for
adjust Basic Picture menu
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
What is Aspect Ratio?
4:3 screen
16:9 screen
Aspect ratio is the ratio of the image width to image height. Standard TV
screens and older laptops are 4:3; HDTV and most DVDs are 16:9; and
widescreen computers are 16:10. If you are projecting onto a screen, the
size/shape of the screen will influence the aspect ratio you decide to use. If
you are projecting onto a blank wall, there are no screen size restrictions.
What you plan to project will also help you choose between 4:3, 16:9 or
16:10. Many TV shows are 4:3, while most movies are 16:9.
4:3
mode
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
widescreen movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for widescreen movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Force Wide can also be enabled to
automatically resize less common aspect ratios to 16:10.
16:9
mode
Native
mode
(NTSC
only)
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
HDMI 1.3 connection
Connecting a video device
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video-out connector on the video device and into the HDMI connector on
the projector.
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3-
compatible source.
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an S-
video cable into the S-video connector on your video device and into the
Video 2 connector on the projector. Use the audio cable as described above.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu
Keep in mind that S-video delivers higher quality video output than
composite.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the VGA 2 or VGA 1 connector on the projector.
Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
Component video connection
Composite video connection
If your HD video device has component connectors, an optional
Component to VGA adapter can be used. Plug the component cable into the
video device. Plug the other end of the component cable into the adapter
and plug the adapter into the VGA 2 or VGA 1 connector. Component offers
the highest quality analog video output. (Digital HDMI provides the
highest overall quality video output.)
Plug the composite video cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the
yellow Video 3 connector on the projector.
Plug the white connector of a Mini-plug audio Y-cable into the left audio
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
the Audio In Video connector on the projector.
Keep in mind that video output from composite connections is not as high
quality as S-video.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
sure the computer is powered on). The battery light will stay on while the
battery is charging, then it will turn off when the battery is fully charged.
LiteBoard™ Wand
The LiteBoard Wand works like a wireless mouse - but one that works in
midair, not on your desktop. Just hold the wand in your hand, and point it
at the projected image to point, click and drag. The wand works with all
your software, just like a regular mouse.
When charging is finished, you can disconnect the USB cable (or keep the
cable connected and use the wand while it’s charging).
NOTE: 5-10 minutes of charging is enough for about an hour of wand use. A
full charge will take 6-8 hours and will allow 20-40 hours of non-stop wand
use.
Computer System Requirements and Connections
Caution: The lithium battery is only rechargeable, and is not user serviceable
or user replaceable.
For the wand to work, a LiteBoard-compatible projector needs to be
powered on and connected to your computer.
Caution: Always use the included USB cable and power adapter (or your
computer) to charge the wand.
The LiteBoard Wand is compatible with any computer and operating
system that supports a standard USB mouse (including Windows,
Macintosh, and Linux). To set up your computer with the wand, make sure
a USB cable is connected between your projector's DisplayLink connector
and a USB port on your computer.
Computer
USB Cable
How to Use the Wand
Follow these steps to use the wand:
1 Connect the projector and your computer with a USB cable (see
Computer System Requirements and Connections above).
IMPORTANT: If you aren’t using DisplayLink to project, you must also
connect the computer’s display output to the projector using a VGA or
HDMI cable.
2 Make sure the wand's battery is charged or charging (see Charging the
Wand's Battery above).
3 Turn on the projector and make sure it's displaying the computer's
screen - set the source to DisplayLink, VGA 1, VGA 2, or HDMI (press
the source button on the projector or its remote if needed - you may
need to press it several times).
Charging the Wand’s Battery
When the wand’s amber battery light starts to blink, its internal battery is
low (if the battery is fully discharged, you won’t be able to turn the wand on
by pressing its tip, L or R buttons).
4 Turn on the wand by pressing its tip, L, or R button - the wand's green
Link light will start to blink.
To charge the battery, open the flap at the rear of the wand to expose the
wand’s USB connector. Then connect a USB cable between the wand and
the USB power adapter, or a computer (if connecting to a computer, make
5 Point the wand at the screen to point, click, and drag - just like a normal
mouse.
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
NOTE: See LiteBoard Wand Menu below for settings that let you fine-tune
wand motion and clicking behavior. When you’re done, set the wand aside
and make sure it isn’t pointing at the screen; it will turn itself off
automatically after 1 minute.
If you have problems, see Troubleshooting (below).
Wand Position and Avoiding Shadows
Your Location Distance from the Screen
You can use the LiteBoard Wand right up against the screen, or around the
room. You might find that your pointing accuracy will improve if you get
closer to the screen. Also, avoid standing too far off from either side of the
screen.
Using More than One Wand
The projector can work with more than one wand, but you can only use one
wand at a time. When you want to switch to a different wand:
Avoid Shadows!
1 Point the current wand away from the projected image for at least 3
The wand won't work if its tip is in a shadow or if it is pointing at a shadow:
seconds.
Correct (no shadow)
Incorrect (shadow)
2 Press the tip, L, or R button on the new wand to turn it on, and then start
using the new wand.
NOTE: Settings in the projector's LiteBoard Wand menu (see below) apply
to all wands used with that projector.
Wand Features
Right mouse
button
Left mouse
button
How to Hold the Wand
Link Light
USB connector
You can hold the wand the way you would hold a normal pencil or pen, or
you can hold it like a remote control - use in whichever position is most
comfortable. NOTES: If the wand is up close to the screen, you can press its
tip against the projection surface to click and drag. Not recommended for
use with fabric screens.
Tip
Sensor
Reset
button
Battery Light
Middle mouse
button
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
Reset Button
Buttons and Wand Tip
The wand's three top buttons are equivalent to the left (labeled 'L'), right
(labeled 'R'), and middle (labeled 'M') buttons on a mouse. The wand's tip is
also a button, and it's also equivalent to the left mouse button. NOTE: By
default, the M button changes wand motion between Normal and Draw.
Normal makes clicking easier, but Draw allows smoother motion. You can
change the M button to perform other functions, including a standard
middle button mouse click (see LiteBoard Wand Menu below).
The wand has a reset button, behind a small hole on its underside. Under
normal conditions, you should not need to reset the wand. See the
Troubleshooting section below for more information.
Internal Radio
The wand has a built-in wireless transmitter/receiver which it uses to
communicate with the projector.
Battery Light
Lithium Battery Information
The amber battery light shows the status of the wand's built-in battery (see
below for battery information). The battery light will turn on while the
wand is charging, and it will blink if the battery is low (2-4 hours of wand
use left).
Manufacturer: KAYO Battery (ShenZhen) Co., Ltd.
Model: ICR14430
Rating: 3.6VDC/650mAh
Caution: Lithium battery is only rechargeable, and not user replaceable. Not
user serviceable.
Link Light
The green link light shows the status of the wand's wireless connection to
the projector. The link light will blink frequently (more than once per
second) when the wand is attempting to link to the projector; then it will
blink less frequently (about once every 4 seconds) after the wand has linked
to the projector. NOTE: The link light will stay off when the wand is off.
LiteBoard Wand Menu
You can access the LiteBoard Wand menu from the projector's Setup menu.
To change the settings in this menu, highlight a setting, then press Select (on
the projector or its remote) one or more times - each press of Select will
change to the next value for the setting.
USB Connector
The wand's USB connector is behind a flap on the back of the wand. The
USB connector is only used for charging the wand's battery - using the
included USB power adapter, or a computer. NOTE: You can use the wand
while charging the battery, but after the battery is charged (battery light
turns off), you can unplug the USB cable and continue to use the wand
without a cable.
Sensor
The wand's optical sensor opening is located above the wand's tip. Don't
block the sensor, and make sure it always has a clear view of the screen.
NOTE: The sensor won't work if you point it at a shadow or away from the
screen.
Enabled: controls whether the projector lets you use LiteBoard Wands. Set
this to Yes to allow wand use. Set this to No to prevent wand use.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Motion: controls wand motion. When set to Normal, motion is set up to
work best for normal computer use. When set to Draw, motion is set up to
work best for on-screen drawing. When set to Stable, motion is filtered for
maximum stability. When set to Press to Move, the mouse pointer only
moves when you hold down the wand’s tip or the L button on the wand
(use the R button to click).
- Make sure the wand is not pointing at a shadow and make sure its tip
is not in a shadow.
- If the room is brightly lit, reduce the room illumination.
- If you're trying to use the computer's mouse at the same time as the
wand, point the wand away from the screen while using the mouse.
- If someone else is using a different wand with the same projector, they
must stop using it before you can use another wand.
- Change the Link Channel value in the LiteBoard Wand menu.
- Reset the wand: push the end of a paper clip into the reset opening on
the underside of the wand.
Click Speed: controls the motion pause when you click; only applies if
Motion is Normal. Longer click speeds will make it easier to double-click,
but will increase the delay before motion resumes after you click.
M Button: selects the function of the wand's M Button. You can use the M
button to change wand motion, or perform keyboard or mouse button
shortcuts. NOTE: The PwrPnt Annotate setting sets up the M button to
control drawing (annotating) during Microsoft PowerPoint slide shows.
The first press of the M button will turn on the drawing function, the next
press will turn off the drawing function, the next press will turn it on again,
etc.
•
If accurate clicking is difficult, try one of these solutions:
- Hold the wand steadier when clicking.
- Use the wand right up against the screen so it's easier to avoid
unexpected movements.
- Change the Motion value in the LiteBoard Wand menu.
•
•
If it is difficult to draw or move freely because the wand wants to move
in straight lines or draw extra lines, try changing the Motion value in
the LiteBoard Wand menu.
If the mouse pointer is in the wrong place on the screen, or the mouse
pointer's movement is restricted to only part of the screen, try one of
these solutions:
- Make sure your projector is displaying the computer's screen and not
some other source (such as DVD, VCR, etc.). To change the source,
press the Source button on the projector or its remote.
Link Channel: selects the radio channel used for wand communication. This
should be set to Auto unless you encounter interference (see
Troubleshooting below for more information).
Troubleshooting LiteBoard
For the most up-to-date information, visit our support site at
- Make sure the projector is displaying the same image as the
computer's main or built-in monitor (don't extend your desktop onto
multiple monitors). To correct this:
On Windows XP: Open the Display control panel, click Settings, click
the display that represents the projector, then un-check “Extend my
Windows desktop...”.
On Windows Vista: Right-click on the desktop, choose Personalize...,
click Display Settings, click the display that represents the projector,
then un-check “Extend the desktop...”
•
If the wand doesn't work at all, or it works intermittently, try one of
these solutions:
- Press to Move may be enabled; try holding down one of the wand’s
buttons while moving the wand.
- Press the tip, L, or R button on the wand to turn it on.
- If the wand's green Link light never blinks, then the wand's battery is
fully discharged; connect the wand to the USB power adapter or your
computer.
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
On Macintosh: Select System Preferences from the Apple Menu, then
select Displays. Click Arrangement, and check “Mirror Displays.”
•
If the battery light does not turn on when the wand is being charged,
try one of the following:
- Make sure a USB cable is connected between the wand and either the
USB power adapter, or a USB port on your computer.
- If the wand is connected to the USB power adapter, make sure the
adapter is plugged in to a live electrical outlet. If the wand is
connected to your computer, make sure the computer is powered on.
- If the wand still won't charge, contact InFocus support at
•
If DisplayLink Manager setup always starts when USB cable is
connected, but you don't want to use DisplayLink projection, you can
disable DisplayLink: Go into the projector's Setup menu and turn off
the DisplayLink Source setting. NOTE: This does not disable the
DisplayLink connector; it only disables being able to project over
DisplayLink.
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Shutting down the projector
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the
projector. The image returns when an active source is detected or a remote
or keypad button is pressed.
Table 3: Status indicator light behavior and meaning
Screen Save Time
You can make the black screen appear after a preset number of minutes by
Icon
Meaning
Power, solid amber
The projector is plugged in.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction
with the projector is performed for 30 minutes. By default, this feature is off.
Power, blinking green
The power button has been pressed and
the software is initializing.
Power, solid green
The projector is on and initialized.
Turning off the projector
Power, blinking amber
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 1 minute while the fans
continue to run to cool the lamp. When the lamp has cooled, the LED lights
amber and the fans stop. Unplug the power cable to completely power off
the projector.
Temperature
The projector is too hot. Make sure the
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
service.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/
support to contact service.
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
Problem
Solution
Result
No start up screen
Correct image
Plug power cord into the projector and press
power button.
Startup
Screen
If your computer is using the projector's DisplayLink
connector, see the DisplayLink Software User's
Guide for troubleshooting information.
Computer image projected
Only start up screen appears
Startup
Screen
Press the Source button
activate laptop’s external port
A
A
A
Restart laptop
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
Problem
Solution
Result
Press the Auto Image Button on keypad. Adjust computer
refresh rate in Control Panel > Display > Settings > Advanced
> Adapter (location varies by operating system)
No computer image, just the words “Signal out of
range”
Computer image projected
A
Signal out of
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image fuzzy or
cropped”
DisplayLink - Use DisplayLink software to change the display
mode from Extended Desktop to Duplicated Desktop.
Windows - Disable "Extend my Windows Desktop" in Control
Panel > Display > Settings > Display 2 (location varies by
operating system)
Only my laptop’s background appears, not the
Desktop icons
Background and Desktop projected
A
A
A
A
Uncheck this
option, then
click Apply
Download from Www.Somanuals.co2m0. All Manuals Search And Download.
Problem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor or turn-
on dual-display
mode
Image not centered on screen
Move projector, adjust zoom, adjust height
Correct image
Adjust horizontal or
vertical position in
Advanced Picture
menu
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
Problem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
Image does not fit 4:3 or 16:9 screen
Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect ratio menu
Correct image
Download from Www.Somanuals.co2m2. All Manuals Search And Download.
Problem
Solution
Result
Image upside down
Turn off Ceiling Mount in Setup menu
Correct image
A
A
Image reversed left to right
Turn off Rear Project in Setup menu
Correct image
Projected colors don’t match source
Adjust color, tint, brightness, contrast in the Basic
Picture menu
Correct image
COLOR
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
Problem
Solution
Result
The video embedded in my PowerPoint presentation If your computer is using the projector's DisplayLink
Embedded video plays correctly
does not play on the screen
connector, see the DisplayLink User's Guide for video
troubleshooting information.
Turn off the internal LCD display on your laptop
A
B
A
B
A
B
Lamp won’t turn on, Temperature light is on
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Startup
Screen
Temperature light
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
Problem
Solution
Result
Lamp turns on
“Replace lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
Lamp must be replaced (on page 47)
Startup
Screen
lamp door
Lamp light
replace lamp
Still need assistance?
Check out our HOW TO section there for additional information on using
this projector for home theater or gaming applications. See the Quick Start
Poster/Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
Download from Www.Somanuals.co2m5. All Manuals Search And Download.
Troubleshooting the remote
Using the remote control
The remote uses two (2) AA batteries. They are easily installed by removing
the cover from the remote’s back, aligning the + and - ends of the batteries,
sliding them into place, and then replacing the cover.
•
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the projector.
Caution:
•
When disposing of the batteries, be sure to do so in an enviromentally
proper manner.
•
•
•
•
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Ensure the batteries' polarity (+/-) is aligned correctly.
navigation
buttons
Do not mix new and old batteries together, or mix different types of
batteries together.
•
•
Replace the batteries as soon as they run out.
Remove batteries from the remote control when storing or not in use
for a prolonged period.
The remote also has:
•
•
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank
•
•
•
•
•
•
Source button to switch between sources.
Blank button to blank the screen.
Mute button to silence the audio.
Auto Image button to resynch the projector to the source.
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
NOTE: DisplayLink and HDMI audio are passed to the Audio Out
connector.
Using the audio
Using the projector’s speakers
When the computer is using the DisplayLink or HDMI connector, both
audio and video are sent over the cable to the projector and audio will play
from the projector's speakers.
connect audio cable
For inputs other than DisplayLink and HDMI, to use the projector's
speakers, connect the audio source to the Audio In Computer or Video
connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
adjust volume
•
If your computer is using the projector's DisplayLink or HDMI
connector, see the InFocus DisplayLink Software User's Guide on the
information.
•
•
•
Make sure the audio cable is connected to the correct Audio In
connector, Computer or Video.
Make sure the volume is turned up enough. Press the Volume button on
the keypad or remote.
Make sure you are connected to the corresponding audio in for your
source. By default, audio in VGA 1/2 corresponds to VGA 1, VGA 2
and LitePort, audio in composite s-video corresponds to S-video and
•
Make sure that you are connected to an audio out connector on the
source as opposed to a line-in or microphone connector.
Adjust the audio source.
external speakers
with own power
source
•
•
If playing a video, make sure the playback has not been paused.
speaker
cable
audio out
Connecting external speakers
The projector can be attached to external amplified speakers by connecting
a 3.5mm stereo audio cable from the Audio Out connector on the projector to
the amplified speakers. Alternatively, you can bypass the projector’s audio
system and connect the audio directly from your source to a stereo or home
theater system.
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
Optimizing computer images
After the projector is running and the image is on the screen, you can
optimize the image using the onscreen menus. For general information on
Presentation features
Several features are provided to make giving presentations easier. Here is
an overview, details are found in the menu section.
•
The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the
•
•
•
•
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
•
•
The Search Screen option lets you change the appearance of the blank
Change the Aspect Ratio. Choose the option that best fits your input
Two options, Auto Off and Screen Save Time, are provided to
automatically shut down the projector after several minutes of
inactivity or display a black screen. This helps preserve lamp life (on
page 34).
Adjust the Color Temperature in the Advanced Picture menu (on
page 33).
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Software User's Guide for information about
optimizing images.
NOTE: To achieve maximum contrast, you can disable LiteBoard Wand use.
To do this, set Enabled to No in the LiteBoard Wand submenu in the Setup
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
You can customize the projector for your specific setup and needs (on
•
•
For rear projection, turn Rear Project on in the Setup menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic
For ceiling mounted projection, turn Ceiling Mount on in the Setup
menu.
•
Change the Aspect Ratio. Choose the option that best fits your input
•
Specify which source the projector checks first for active video during
power-up.
•
•
•
•
•
•
•
•
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Adjust the Color Temperature. Select a listed warmth value (on
page 33).
•
Turn on Overscan to remove noise on the edges of the image (on
page 33).
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
Save settings for the active source as a preset.
NOTE: To achieve maximum contrast, you can disable LiteBoard Wand use.
To do this, set Enabled to No in the LiteBoard Wand submenu in the Setup
Dynamic Messaging
Using command codes, text messages can be sent for display by the
projector over a network or serial connection. Text is shown on top of
whatever else is being displayed, and can be shown in ticker tape format or
in a box, with optional beep tone alert. This is a great way to display urgent
alert messages to employees, and simply requires a connection to the
projector's RS-232 serial control or LAN connector. Command codes for
executing Dynamic Messaging are available on our website at
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
Using the menus
keypad navigation
buttons
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use
the arrow buttons to move up and down to highlight the desired menu,
then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value or select an option or turn the
feature on or off. Press Select to confirm your changes. Use the arrows to
navigate to another setting. When your adjustments are complete, press
Menu to access a different menu; press the Menu button at any time to
navigate to the higher-level menu and ultimately close the menus.
The menus are grouped by usage:
•
•
The Basic Picture menu provides common image adjustments.
The Advanced Picture menu provides more complex image
adjustments.
•
•
The Setup menu provides set-up type adjustments that are not changed
often.
Basic Picture menu
Advanced Picture menu
The Status and Service menu provides information about the projector
and source.
Setup menu
Status and Service menu
Download from Www.Somanuals.co3m1. All Manuals Search And Download.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if its
size has been changed by the Digital Zoom setting.
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Sharpness: changes the clarity of the edges of a video image. Select a
sharpness setting.
Basic Picture menu
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video images.
The tint setting applies to NTSC video sources only.
Auto Image: Forces the projector to reacquire and lock to the input signal.
This is useful when signal quality is marginal.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch
enhanced widescreen DVDs.
More Aspect Ratio information is available on page 11.
Aspect ratio
Apply Preset...: Presets are provided that optimize the projector for
displaying computer presentations and video images under certain
conditions.
There is also a user-definable preset. To set this preset, adjust the image and
select Save User in the Presets menu. You can recall these settings in the
future by selecting the User preset.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
increasing keystone
decreasing keystone
Digital Zoom: changes the size of projector’s display area. If the display area
has been resized by this setting, it can be moved by changing the Horz Shift
and Vert Shift settings.
Download from Www.Somanuals.co3m2. All Manuals Search And Download.
Advanced Picture menu
BrilliantColor™: produces an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images. Choose
Normal Look for most video sources and Bright Look for most computer
sources.
White Peaking: increases the brightness of whites that are near 100%.
Color Temperature: changes the intensity of the colors. Select a listed relative
warmth value.
Advanced Picture menu
Force wide: when this is off, the analog locking algorithms choose the
standard mode resolution (4:3) as the preferred default resolution. When
this is on, the analog locking algorithms choose wide mode resolution
(16:10) as the preferred default resolution.
Overscan: removes noise around the video image.
Phase: adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Color Space: applies to computer and component video sources. It allows
you to select a color space that has been specifically tuned for the input
signal. When Auto is selected, the projector automatically determines the
standard. To choose a different setting, turn off Auto, then choose RGB for
computer sources or choose either REC709 or REC601 for component video
sources.
Gamma: select the appropriate gamma from among Video, Film, Bright, and
CRT.
Color Gain: adjusts the gain of the red, green or blue channel of the image.
Color Offset: adjusts the offset of the red, green or blue channel of the image.
Horizontal/Vertical Position: adjusts the position of a computer source.
Download from Www.Somanuals.co3m3. All Manuals Search And Download.
•
•
•
•
•
•
Freeze Screen: pauses the projected image.
Setup menu
Source Info: the default action. Shows the Source Info menu.
Projector Info: shows the Projector Info menu.
Overscan: removes noise around the image.
AV Mute: enables or disables AV Mute function.
Closed Captions: enables or disables Closed Captions.
Language: allows you to select a language for the onscreen display.
LiteBoard Wand: allows you to control the operation of the LiteBoard Wand
network configuration and operation.
Blank Key: select what to display when the blank key on the remote is
pressed: your custom snapshot, a solid color screen (blue, black or white),
the factory logo screen, a timer, or test patterns. The timer option is useful
for classroom tests or break times during meetings.
•
•
•
•
•
•
•
•
DHCP: turns the DHCP on or off.
IP Address: assign Network IP Address.
Subnet Mask: assign Network Subnet Mask.
Default Gateway: assign Network Default Gateway.
WINS Host Name Lookup: turns WINS Host Name Lookup on or off.
Host Name: displays the host name.
Source Key Enable: enables or disables Source Keys on the optional
Commander-2 remote.
AC Power On: when this feature is on, the projector automatically turns on
when electrical power is connected. This allows control of ceiling mounted
projectors with a wall power switch.
MAC Address: displays network MAC Address value.
Show Network Messages: turns network messages on or off. Network
messages display the projector’s IP address (and host name if enabled)
when the projector is also displaying source messages.
Auto Off Time: automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
•
•
Restart Network...: restarts the network.
Screen Save Time: automatically blanks the screen with a black color after no
signals are detected for a preset number of minutes. The image returns
when an active source is detected or a remote or keypad button is pressed.
Network Factory Reset...: performs factory reset.
Key Click: turns the key click sound on or off. When this setting is on,
pressing keys on the keypad causes the projector’s speaker to play a “click”
sound.
Sleep Timer: Allows the projector to automatically power off after it has been
on for a specified amount of time.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and
press Select to choose a different one.
Always-On Functions: allows you to control which projector functions will
work even when the projector is in standby (powered off but connected to
AC Power). Press Up or Down to highlight the function you want to
change, then press select or left and right to change the function to either
Yes or No. Press menu when done. Note that some functions must always
have the same value; in this case when you change one value, other values
in the submenu may also change automatically.
•
•
•
Blank Screen: displays an empty screen.
Mute: turns off all sound.
page 32).
Lamp Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter.
•
•
Source: cycles through available sources.
Download from Www.Somanuals.co3m4. All Manuals Search And Download.
Power Sounds: controls whether the projector makes a sound when powered
Closed Captions: controls closed caption display while audio is not muted. If
this setting is not off, and audio is not muted, and the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
on and off.
Audio Inputs: assign an audio input to a specific video/computer source
input. Press up or down to highlight the source you want to change, then
press Select or the left and right arrow keys to change the source’s audio
input. Press Menu when done changing audio inputs.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Rear Project: reverses the image so you can project from behind a
Auto Source: when this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this
feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by
pressing the Source button on the remote or keypad.
translucent screen.
Auto Keystone: automatically adjusts vertical image.
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
Search Screen: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Take Snapshot...: captures the current image and allows it to be used as the
search screen image.
Disable Snapshot: Allows the user to disable the snapshot capability.
Show Messages: displays status messages (such as “Searching”) in the lower-
left corner of the screen.
Setup menu
Menu Offset: allows you to change the position of the On Screen Display
items.
Power-up Source: determines which source the projector checks first for
active video during power-up.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image
behind the menu is visible.
DisplayLink Source: allows you to disable DisplayLink (project over USB).
When Off, you won’t be prompted to install DisplayLink software when
you connect the USB cable to your computer.
Magnify Controls: determines whether the select key can be used to change
Video Standard: When this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives.
(The video standard options may vary depending on your region of the
world.) If the projector is unable to detect the correct standard, the colors
may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
the Video Standard menu.
magnify settings when the OSD menu is not visible.
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image. The default PIN on this
projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the
remote or keypad to enter the correct 5-button press sequence. When all 5
numbers are entered correctly, press the Select button on the remote or
keypad to select OK. If the message “Wrong PIN” appears, verify the code
and re-enter it. If you mis-enter a number, you must enter 5 numbers and
press the Select button in order to access the “Wrong PIN” message and re-
enter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the
startup screen. Enter the PIN. Use the navigation buttons on the remote or
keypad to enter the correct button press sequence. See the description above
for instructions.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the
new PIN. You can navigate between OK and Cancel by pressing the up and
down buttons on the keypad. Select OK or Cancel by pressing the Select
button. Verify the new PIN.
If you lose or forget your custom PIN:
Contact InFocus support. Go to www.infocus.com/support
Keypad: Enables or disables keypad.
VGA 2 SCART: selects SCART connection type between RGB and composite.
Serial Port, Baud Rate: selects the serial port and baud rate.
Serial Port Echo: controls whether the serial port echoes characters.
Download from Www.Somanuals.co3m6. All Manuals Search And Download.
Status and Service menu
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings.
LiteBoard Info: a read-only display of current LiteBoard settings.
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info
menu to zero. Do this only after changing the lamp.
Factory Reset: restores all settings to their default.
Status and Service menu
Service Code: only used by authorized service personnel.
Download from Www.Somanuals.co3m7. All Manuals Search And Download.
NOTE: If you still do not see an IP address, go to the projector’s Setup menu,
select Network, then turn on Show Network Messages. After exiting the
menu, press the Source button again.
Using Network Functions
IMPORTANT: To enable network functions at all times (even when the
projector is powered off), the Network item in the Always-On Functions
submenu in the Setup menu must be set to Yes (not No).
3 Select IP Address. This will highlight the first of the four octets in the IP
address. Press Up or Down to change the value, then press Select or Right
when done to move to the next octet. Repeat until you have changed all
four octets in the IP address.
Projector network functions include:
•
•
•
•
Configuring and controlling the projector via a web browser.
Failure and warning alerts via email.
Projector Management via SNMP.
4 Repeat the above for Subnet Mask, Default Gateway, and other settings
that are in IP address format (to assign or change the Host Name, see
Network Settings Page below).
Controlling the projector via Scheduling.
NOTE: Projector web pages and emails sent by the projector are always
displayed in English language.
For network control, you can access the projector through Port 23 (Telnet).
We use the same control codes on serial as we do over the network. InFocus
network control uses the Telnet packet structure.
Configuring and Controlling the Projector via a Web Browser
You can adjust or control the projector via a network from a web browser on
a computer that is connected to the same network as the projector.
Before using the network functions
NOTES:
To use the network functions of the projector, the projector must be
configured to suit your network. Consult with your network administrator
before connecting the projector to your network; incorrect network
configuration of the projector may cause problems on your network.
•
To access the projector's web pages, the projector must be connected to
the network and connected to AC power (and if you want to access the
network even when the projector is powered off, make sure the
Network item in the Always-On Functions submenu in the Setup menu
is set to Yes).
Connect the Network Cable
Properly connect projector to the network, then configure the following
settings.
•
•
JavaScript must be enabled in your browser to use the projector web
pages properly. If JavaScript is disabled, see the Help files for your web
browser for details on how to enable it.
If Using a Network with DHCP Enabled:
3 Use the projector's remote control or keypad to select the Network item
in the projector's Setup menu.
If no operations are performed in the web browser for approximately
ten minutes, the system will automatically log you off.
4 If DHCP is off, select it to turn it on.
Logging in
If Using a Network that Does Not have DHCP Enabled:
1 Use the projector's remote control or keypad to select the Network item
in the projector's Setup menu.
To log into the projector web pages, follow these steps:
1 Make sure the projector is connected to the network and connected to
AC power.
2 If DHCP is on, select it to turn it off.
Download from Www.Somanuals.co3m8. All Manuals Search And Download.
NOTE: If a Basic User is logged in, only the Controls, Basic Picture, and
Advanced Picture tabs are shown.
2 If you don't know the projector's IP
address, turn on the projector. After the
projector starts up, if its IP address is not
shown, press the Source button to view the IP address.
In each tab, the current value of each setting is shown in blue color.
NOTE: Unlike other pages, changes you make to Projector Control settings
3 Start a web browser on your computer.
are applied immediately.
•
•
•
•
To change an on/off setting (e.g. Power): Click the corresponding On or
Off button.
the web browser's address bar. Example: If the IP address is
To change a multi-value setting (e.g. Sharpness): Select a value from the
drop-down menu.
5 The Log In to Projector Control page will be shown in the browser.
6 Select Access type: Basic User or Administrator.
7 Click Log In.
To change a numeric setting (e.g. Brightness): Click the corresponding +
or - button, or select a value from the drop-down menu.
To perform a command (e.g. Auto Image): Click the corresponding
Execute button.
Network Settings Page (administrators only)
Navigating Projector Web Pages
This page lets you view and change the projector's network settings.
Consult with your network administrator before making any changes on
this page; incorrect network configuration of the projector may cause
problems on your network.
The left side of every page shows a navigation bar. Click the links in the
navigation bar to go to different projector web pages.
NOTE: If a Basic User is logged in, no links are shown.
The top of the navigation bar shows the projector name, model, and serial
number.
Projector Name: The name of the projector shown in the projector's web
pages.
The web pages also include the following options:
IP Address: These settings control the projector's network configuration.
Enter the appropriate settings required for your specific network.
•
•
•
Log Off: Logs off and returns to the Log In page (see above).
Refresh: Reloads the page with current status.
Advanced Network Settings: Click this link to show advanced settings:
Defaults: Displays default (factory settings) values (to save these values
click Apply).
802.1x Authentication: If your network requires 802.1x authentication, enter
the user name and password that the projector should use, and select the
authentication type.
•
Apply: Saves the values that are currently shown on the page.
Projector Controls Page (All users)
SNMP: If your network uses SNMP, enter necessary SNMP information
here.
This page lets you control the same settings that are available via the
projector's main menu and remote control. The Controls tab includes basic
remote control functions; other tabs correspond to the projector's menus.
Download from Www.Somanuals.co3m9. All Manuals Search And Download.
Command and Control Pass-Through: This setting allows you to send and
receive projector commands over the network. For command codes, see the
Time Zone: The projector's time zone (if you are in a different time zone
from the projector, make sure this is the time zone of the region where the
projector is located).
Set Now: Click this to immediately set the time and date based on the above
information.
Event Notifications Page (administrators only)
This page lets you configure the projector to automatically send email when
specific events occur.
Daylight Savings Settings: Click this link to show daylight savings settings:
Start: Select when daylight savings starts.
E-Mail Settings tab: In the Account Used… section, enter the information
needed for your projector to connect to an email sending (SMTP) server.
Then in the Recipient E-Mail Addresses section, enter the email addresses of
people who will receive emails, and for each address, select whether that
address receives reminders and/or warnings and errors (enter only one
address per line). After you have completed this page, click Send Test to
make sure that email is correctly set up.
End: Select when daylight savings ends.
Automatically adjust…: Check this to have the projector automatically update
time and date when daylight savings starts and ends.
Scheduled Tasks Page (administrators only)
This page lets you configure the projector to perform tasks automatically on
specific days and times. You can set up a maximum of three different
scheduled tasks; each tab corresponds to a task. Each scheduled task can
perform different commands on different days and times. Each tab contains
the following items:
Reminders tab: Select which types of reminders to send. For most reminders,
you can adjust the frequency or date/duration associated with the
reminder.
Warnings & Errors tab: Select which warnings and errors to send.
Date/Time Settings Page (administrators only)
On/Off: Select whether or not this scheduled task will run on the days and
times shown.
This page lets you configure the projector to read the time and date from an
SNTP server on your network. NOTE: The projector does not have a built-in
clock. If the projector is unable to access the SNTP server, or no SNTP server
is defined, functions that rely on the time and date may not work correctly.
Description: Explanation of what the task does.
Run Every: Select the days of the week when the scheduled task should run.
Current Date and Time: Shows the current date and time read from the SNTP
server.
At Time(s): Select the times of day when the scheduled task should run (the
task will run at the indicated times on every one of the days checked above).
Synchronize the system clock…: Select how often the projector should check
the SNTP server to get the time and date. Between checks, the projector will
keep track of the amount of time elapsed, allowing it to maintain the correct
time and date.
Command Sequence and Available Commands: The Command Sequence list on
the left shows commands currently performed by the scheduled task (each
task can include up to 20 commands). The Available Commands list on the
right shows all commands that can be added to a scheduled task.
SNTP Server: The address of the time and date server on your network.
<< Add: Adds the command selected in the Available Commands list to the
Command Sequence list.
>> Remove: Removes the command selected in the Command Sequence list.
Download from Www.Somanuals.co4m0. All Manuals Search And Download.
Move Up: Moves up the command selected in the Command Sequence list.
Network Utilities Page (administrators only)
This page lets you perform various network-related projector tasks.
Move Down: Moves down the command selected in the Command Sequence
box list.
Save and Load Projector Configuration: These functions save and load all
network-related projector settings into/from a file stored on your
computer. This lets you quickly 'clone' network settings from one projector
to other projectors.
Clear All: Erases all commands in the Command Sequence list.
Custom: Click this link to show custom command entry options. With
custom commands, you can perform additional commands not shown in
the Available Commands list. The RS-232 command codes are available in
Custom commands you enter here should be in write format (do not
include '?'), and should use '<' and '>' instead of '(' and ')'. Example: to turn
on the ceiling mount setting, use the custom command <CEL1>.
Upgrade Projector Network Firmware: Upgrades the firmware for the
projector's network and LitePort features (this firmware is separate from the
regular projector firmware).
Restart Projector Network Subsystem: Restarts the projector network
subsystem; does not change any projector settings.
User Access and Security Page (administrators only)
This page lets you configure security options for the projector, including log
in passwords and projector access restrictions.
Network Subsystem Factory Reset: Returns all network and LitePort settings
to default values and then restarts the projector network subsystem.
Troubleshooting Network Functions
Web Access - Administrator tab: Select whether or not Administrators must
enter a password to log into the projector's web pages. If a password is
required, click create or change password to update the administrator
password.
•
If network status is shown as Not Connected in the projector's Network
menu, or the projector does not display its IP address, check the cable
or the network configuration.
•
If your web browser displays Page Not Found or a similar error when
you try to access the projector's web pages, verify that the projector is
connected to the network (select the Network item in the projector's
Setup menu and verify that Network Status shows as Connected); if
there is no connection refer to the troubleshooting item above for more
help.
Web Access - Basic User tab: Select whether or not Basic Users must enter a
password to log into the projector's web pages. If a password is required,
click create or change password to update the basic user password.
Projector PIN tab: Allows you to turn projector PIN protection on or off, or
change the PIN. When PIN protection is on, the current PIN must be
entered when the projector is powered on, otherwise the projector will not
operate. NOTE: PIN protection only applies to projector operation via the
projector's keypad and remote control; it does not affect the projector's web
pages.
•
Make sure the Network item in the Always-On Functions submenu in
the Setup menu is set to Yes (if it is set to No, the projector web pages
will only be available when the projector is powered on).
•
•
If scheduled tasks are not performed, check if the SNTP is set up
correctly and is online. Also check if the Command sequence is correct.
System Log Page (administrators only)
This page shows a log of the 100 most recent projector events.
If automatic emails are not sent, check if SMTP is set up correctly and is
online.
Erase Log…: Click this to erase all events in the log.
To manually restart the projector network subsystem: Use the projector's
remote control or keypad to select the Network item in the projector's Setup
Download from Www.Somanuals.co4m1. All Manuals Search And Download.
menu. Then scroll down and select either Restart Network (to restart the
network subsystem without changing any settings), or Network Factory
Reset (to return all network settings back to default values, and then restart
the network subsystem). If the manual restart procedure does not work: To
force the network subsystem to restart, disconnect the projector from AC
power, wait 10 seconds, then reconnect AC power.
Download from Www.Somanuals.co4m2. All Manuals Search And Download.
buttons to scroll through the thumbnails, or press Select when an image is
highlighted to start the slide show, or press Select when a folder is
highlighted to open that folder.
Using LitePort
LitePort displays a slide show of JPEG images stored on a USB flash drive
connected to the projector. This feature eliminates the need for a computer
source and can be integrated with common wall plates and conference room
input/output panels.
To start the slide show: While viewing thumbnails, press the arrow buttons
to highlight a thumbnail, then press the Select button to start the slide show
at the highlighted image.
Image File Types
To change the image during the slide show: Press the Down or Right button to
go to the next image, or press the Up or Left arrow button to go to the
previous image (the slide show may also advance automatically depending
on the value of the Next Slide setting; see the LitePort Menu section below
for details).
LitePort displays image files in JPEG format only (file extensions .JPEG and
.JPG). Other file types including PDF, BMP, TIFF, PNG, GIF, etc. are
ignored.
Viewing a Slide Show
To view your pictures as a slide show, follow these steps:
To change to a different folder: While viewing thumbnails, press the arrow
buttons to highlight the desired folder icon, then press the Select button (to
go to the higher-level folder, select the folder icon labeled "Up").
1 Connect a USB flash drive to your computer and copy JPEG files from
your computer to the USB flash drive.
To change LitePort settings: Press the Menu button during the slide show, or
while viewing thumbnails (see the LitePort Menu section below for details).
2 Turn on your projector if needed.
3 Remove the USB flash drive from your computer and plug it into the
Using the LitePort Menu
LitePort connector on the rear of the projector.
To show the LitePort menu, press the Menu button on the keypad or remote
during the slide show, or while viewing thumbnails. To highlight a menu
item, press the arrow buttons. Then to do the action or change the setting,
press Select. To remove the menu, press the Menu button again.
4 The projector will start a slide show of the images found (if you see
image thumbnails instead, see To Start the Slide Show section below).
5 To go to the next image in the slide show, press the Down or Right
arrow button on the projector keypad or remote. To go to the previous
image, press the Up or Left arrow button.
Rotate Picture: Rotates the current image by 90 degrees clockwise (rotation is
temporary; the image returns to its original orientation when the USB flash
drive is removed from the projector or when the projector is turned off).
Stop/Start Slideshow: Stops the slide show, or starts it at the selected
thumbnail (when the menu is not visible, you can also stop or start the slide
show by pressing the Select button).
Controlling LitePort
When you plug a USB flash drive into the projector's LitePort connector, the
projector will scan the drive and then either start a slide show or show
image thumbnails.
Go to Projector Main Menu: Removes the LitePort menu and displays the
projector's main menu, where you can adjust the picture or change other
projector settings.
To stop the slide show and view thumbnails: Press the Select button during the
slide show. In Thumbnails view, the name of the current folder, the current
image number, and the total number of images in that folder are shown at
the bottom of the screen. While viewing thumbnails, press the arrow
Download from Www.Somanuals.co4m3. All Manuals Search And Download.
(For remaining items below, highlight the setting, then press Select one or
more times to change the setting value.)
Click the Slides sized for drop-down menu and select Custom. Change
both Width and Height to double their previous values, then click OK.
Auto Start: Select On to have the player start the slide show when the USB
flash drive is first connected. Select Off to have the player display
thumbnails when the USB flash drive is first connected.
4 Click the Office button in the upper left corner of the PowerPoint
document window.
5 Point to Save As, then click Other Formats.
Show All Folders: Select On to have the slide show display all images in all
folders. Select Off to have the slide show display images only from the
current folder.
6 In the Save As dialog box, click the Save as type drop-down menu. Scroll
through the menu and select JPEG File Interchange Format.
Fill Screen: Select On to have the slide show expand small images to fill the
screen. Select Off to have the slide show display small images at their
original size.
7 Make sure the contents of your USB flash drive are visible in the Save As
dialog box before you continue - to view your USB flash drive in the
Save As dialog box, first click My Computer, then double-click the USB
flash drive's icon (make sure you do both of these in the Save As dialog
box, not on your computer's desktop).
Next Slide: Select Manual to disable automatic slide advance in the slide
show. Select other values to make the slide show advance to the next image
automatically (regardless of this setting, manual advance is always
available by pressing the arrow buttons).
8 Click Save. PowerPoint will ask if you want to export every slide or only
the current slide; click Every Slide. PowerPoint will save each slide in
your presentation as a separate JPEG file. These files are saved in a new
folder that has the same name as the original document.
Effect: Select Off to have no transition effect when changing between images
during the slideshow. Select Random to use a different random effect for
each transition. Select other values to use a specific effect.
9 Remove the USB flash drive from your computer and plug it into the
projector's LitePort connector.
Show Info: Select On to show the name of the current file and folder, the
current image number, and the total number of images in the slide show at
the bottom of the screen. Select Off to hide this information.
10 On the projector, navigate to the folder created in step 8 and then start
the slide show (for instructions on navigating and controlling the slide
show, see the Controlling LitePort section above).
Displaying PowerPoint Slides
Follow the steps below to display PowerPoint slides using LitePort (these
instructions apply to PowerPoint 2007 in Windows; for other presentation
programs refer to the program's instructions or help file for the steps
needed to save a presentation as separate JPEG files):
NOTE: PowerPoint embedded videos, transition effects, and animations are
not included when saving as JPEG. However, you can select a LitePort
slideshow transition effect by changing the Effect in the LitePort menu.
1 Connect the USB flash drive to your computer.
2 Open your PowerPoint document.
3 This step is optional but improves image quality: Click the Design tab
near the top of the PowerPoint document window, then click Page Setup.
Download from Www.Somanuals.co4m4. All Manuals Search And Download.
Troubleshooting LitePort
•
If images load slowly: Make sure you are using a newer USB 2.0-
compatible (high speed) USB flash drive. Larger image file sizes may
also slow down the player; to reduce file size, use an image editing
program on your computer to resize images smaller; for the best
balance between image quality and speed, resize images to be 1024
pixels wide.
•
•
If no images are found, or some images are not shown, or you only see
folder thumbnails but no images: Make sure that images are JPEG file
type (file extensions .JPEG and .JPG); other file types are not supported
and will be ignored.
If you see a blank screen, or a logo, or the wrong input source
(computer, video, etc.) instead of your images: Keep pressing the
Source button on the keypad or remote until the LitePort message is
displayed (if you still don't see any images, make sure the USB flash
drive is correctly and completely plugged into the projector's LitePort
connector).
•
•
If nothing happens when you connect your USB flash drive, and you
cannot select the LitePort input source as described above: Check the
format of your USB storage device. LitePort only supports USB storage
devices formatted as FAT32. Devices formatted as NTFS, and non-
storage devices (such as cameras) are not supported.
If images saved by PowerPoint are low quality: Make sure to do step 3
when following the steps in the Displaying PowerPoint Slides section
above.
Download from Www.Somanuals.co4m5. All Manuals Search And Download.
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
• Turn the projector off and unplug power cord before cleaning any
part of the projector.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and
removing covers may expose you to dangerous voltage and other
hazards. Refer all servicing to qualified service personnel.
Download from Www.Somanuals.co4m6. All Manuals Search And Download.
1 Turn off the projector and unplug the power cord.
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of
hours the lamp has been in use. Twenty hours before the lamp life expires,
the message “Replace lamp” appears on the screen at startup.
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Remove the lamp door by: (a) removing the screw (labeled “1”) on the
side of the lamp door, (b) turning the lamp cover knob (labeled “2”)
counterclockwise to push up the lamp cover, and (c) lifting the door off.
•
NOTE: Be sure to use the InFocus lamp module designed for this
areas), your retailer or your dealer. Only genuine InFocus lamps are tested
for use in this projector. Use of non InFocus lamps may cause electrical
shock and fire, and may void the projector warranty. InFocus is not
liable for the performance, safety or certification of any other lamps.
turn off and unplug
projector
wait 60 minutes
WARNINGS:
•
The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
c
•
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
•
•
•
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can
obscure projection sharpness and may cause the glass to shatter.
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it.
•
•
Before replacing a ruptured lamp, clean the lamp compartment and
dispose of cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
a
b
•
Hg – Lamp contains mercury. Manage in accordance with local
Download from Www.Somanuals.co4m7. All Manuals Search And Download.
4 Loosen the captive screws that attach the lamp housing to the projector.
Carefully remove the lamp housing. Dispose of the lamp in an
environmentally proper manner.
loosen screw
5 Install the new lamp module and tighten the screws.
6 Replace the lamp door by sliding it into place and tightening both
screws.
7 Plug in the power cord and press the Power button to turn the projector
back on.
8 To reset the lamp hour timer, navigate to the Status and Service menu and
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to
the information that came with the lock for instructions on how to use it.
security lock
Download from Www.Somanuals.co4m8. All Manuals Search And Download.
D
INDEX
F
Numerics
Freeze Screen 34
A
Auto Image 34
G
H
I
Image
B
K
Blank Screen 34
C
L
M
Connecting
Mute 34
N
O
Download from Www.Somanuals.co4m9. All Manuals Search And Download.
P
Projector
Source 34
T
U
V
W
R
Z
S
Download from Www.Somanuals.co5m0. All Manuals Search And Download.
|