IN3102 IN3104 IN3106 IN3108
Regulatory models W3220, W3240 and W3260
010-0710-03
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
Required computer connections
(DisplayLink or VESA)
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
9
•
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
25
26
Use only InFocus-approved ceiling mounts. Warning: To prevent eye
injury if the projector is ceiling mounted, wear protective eyewear
before opening lamp door. A warning sticker is included with the user
documentation. Place this sticker on the lamp door if the projector is
mounted on the ceiling.
•
•
Only genuine InFocus lamps are tested for use in this projector.
InFocus is not liable for the performance, safety or certification of any
other lamps. The use of other lamps violates the projector warranty and
voids all certification marks on this projector.
Use only the power cord provided. A surge-protected power strip is
recommended.
Presentation features
•
•
Refer to this guide for proper startup and shutdown procedures.
Hg – Lamp contains mercury. Manage in accordance with local
•
In the unlikely event of a lamp rupture, particles may exit through the
projector side vents. When the projector is turned on, keep people,
food, and drinks out of the "keep out" area under and around the
projector, as indicated by the "X" areas below.
Customizing the projector
m
5
8
.
/ 1
’
/ 2
.
4
m
’
5
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Introduction
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing too. The IN3102/
IN3104 has native XGA 1024x768 resolution, and the IN3106/IN3108 has
WXGA 1280x800 resolution. This guide applies to all products. They are
compatible with a wide variety of computers and video devices.
zoom (rear ring)
touch keypad
focus (front ring)
Product specifications
To read the latest specifications on your multimedia projector, be sure to
remote control
receiver (IR)
Accessories
The standard accessories that came with your projector are listed in the
included Quick Start Poster/Booklet. Optional accessories can be found on
lens
elevator foot
Online registration
activate your warranty and receive product updates, announcements, and
registration incentives.
power cord
connector
remote control
receiver (IR)
connector
panel
elevator foot
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Connector panel
The projector provides both computer and video connection options,
including:
•
•
•
•
•
•
VESA computer (2)
composite
video
HDMI for video
computer
monitor out
HDMI, for computer (1) and for video (1)
S-video
audio in
S-video
Composite video
Separate audio inputs for video and computer
USB DisplayLink connector, for computer audio/video input. This
USB connection also provides slide advance (and mouse control when
used with an optional remote control only)
The projector also provides the following connectors:
•
Monitor out, to provide an image on your desktop computer as well as
on the projection screen
audio out
•
•
Audio out, to provide sound for external speakers
A 5 volt DC output (see below)
5 volt output
security lock RS-232
DisplayLink
connector
It also has an RS-232 connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
NOTE: DisplayLink video and audio is not sent to monitor out and audio
out.
5 volt DC output
The 3.5mm mini-jack triggers provide a 5 volt, 2 amp DC output. It provides
a constant output while the projector is on. It is designed to provide power
for an InFocus LiteShow II wireless device, which allows wireless
projection. More information can be found on our website at
www.infocus.com or at your retailer or dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Positioning the projector
10 ft high
image
10 ft high
image
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
(IN3102 & IN3104)
(IN3106 & IN3108)
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
Projection angle
Projection angle
bottom of image
1.24 ft above center
of lens
bottom of image
1.5 ft above center
of lens
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase
extension cables). To ensure adequate cable access, do not place the
projector within 6 inches (.15m) of a wall or other object.
lens center
lens center
•
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling mount” on page 31. We
recommend using an InFocus authorized ceiling mount.
Table 1: (IN3102 & IN3104)
Range of distance to the screen for a given screen size
•
•
Position the projector the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
Distance to screen
Minimum
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Distance (feet/
m)
The image exits the projector at a given angle. IN3102/IN3104 image
offset is 115%; IN3106/IN3108 image offset is 112.4%. This means if
you have an image 10’ high, the bottom of the image will be 1.5'
(IN3102/IN3104) and 1.24' (IN3106/IN3108) above the center of the
lens.
60/1.5
80/2.0
90/2.3
150/3.8
8.6/2.6
7.8/2.4
11.5/3.5
12.9/3.9
21.5/6.6
10.4/3.2
11.7/3.6
19.5/5.9
Table 2: (IN3106 & IN3108)
Range of distance to the screen for a given screen size
Distance to screen
Minimum
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Distance (feet/
m)
60/1.5
7.3/2.2
6.5/2.0
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Table 2: (IN3106 & IN3108)
Range of distance to the screen for a given screen size
Distance to screen
Minimum
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Distance (feet/
m)
80/2.0
90/2.3
150/3.8
9.7/2.9
8.7/2.7
9.8/3.0
16.3/5.0
10.9/3.3
18.1/5.5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Projector and device connector guide
The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as
computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite tuners,
camcorders, video games (progressive and interlaced), and laser disc players.
composite
video
HDMI for video
monitor out
computer
audio in
S-video
audio out
5 volt output
DisplayLink
connector
security lock RS-232
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Attach to Adapter or
Labeled Connector
on Projector
If Your Device
Connector Is
Video Device
Video Compatibility
For Setup Instructions, see
Comments
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 3
or Video 2
Not for progressive
(i.e. HDTV) sources.
Standard Broadcast TV (not
HDTV) via: cable, digital cable,
satellite TV, DVD, or VCR
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 3
or Video 2
Not for progressive
(i.e. HDTV) sources.
Standard Video Camera
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 3
or Video 2
Not for progressive
(i.e. HDTV) sources.
Standard Video Game
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Attach to Adapter or
Labeled Connector
on Projector
If Your Device
Connector Is
Video Device
Video Compatibility
1080i, 1080p, 720p
Component 480i
For Setup Instructions, see
Comments
VGA
Computer 3 or
Computer 2
Component video
Computer 3 or
HDTV
(High Definition TV)
Computer 2 via
optional VESA to
Component adapter
HDMI
HDMI connection on page 14
1080i, 1080p, 720p
VGA
Computer 3 or
Computer 2
Component 480p
and 480i
Component video
Computer 3 or
Progressive DVD
Computer 2 via
optional VESA to
Component adapter
HDMI
HDMI connection on page 14
1080i, 1080p, 720p
VGA
Computer 3 or
Computer 2
Component 480p
and 480i
Component video
Computer 3 or
Progressive Video Game
Computer 2 via
optional VESA to
Component adapter
HDMI
HDMI connection on page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Connecting a computer source
connect USB cable
Required computer connections (DisplayLink or VESA)
If your computer has Windows XP SP2 or newer*, connect the USB cable
between your computer's USB port and the projector's DisplayLink connector,
then follow the instructions on the screen. See the DisplayLink Manager
User's Guide for more information.
MOLEX
MOLEX
* For the latest information about support for other operating systems
(including Apple), go to www.infocus.com/support/displaylink
connect computer cable
Or, connect one end of the provided computer cable to the Computer 2 or
Computer 3 connector on the projector and the other to the VESA connector
on your computer. If you are using a desktop computer, you will need to
disconnect the monitor cable from the computer’s video port first (you can
connect this monitor cable to the Monitor Out connector on the projector, see
below).
connect power cord
Connect the black power cord to the Power connector on the side of the
projector and to your electrical outlet. The Power light on the Status
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In Computer connector on the
projector. You may also need an adapter.
connect audio cable
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
connect monitor cable
NOTE: DisplayLink video and audio is not sent to monitor out and audio out.
To advance slides in a PowerPoint presentation using the remote control,
plug the USB cable into the USB mouse connector on your computer and
the DisplayLink connector on the projector.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Displaying an image
Touch the Power button.
press Power button
The Power button blinks green and the fans start to run. When the lamp
comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VESA cable to connect your computer to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to
learn your laptop’s key combination.
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the keypad.
? Is your laptop connected to the projector's DisplayLink connector? See the
InFocus DisplayLink Manager User's Guide for troubleshooting
information.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
adjust height
release button
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent at the side of the
projector.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
Adjust the zoom or focus.
adjust zoom or focus
focus (front ring)
zoom (rear ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Basic Picture menu. See page 29 for
help with these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
adjust Basic Picture menu
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Connecting a video device
4:3 screen
16:9 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
4:3
mode
Do Not Use
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu.
16:9
mode
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a
screen, the size/shape of the screen may determine which aspect ratio to
use. If you are projecting onto a blank wall, you don’t have the screen size
restriction. What you plan to project will also help you choose between 4:3
and 16:9. Most TV shows are 4:3, while most movies are 16:9.
Native
mode
(NTSC
only)
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
VESA connection
Video device connections
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the Computer 3 or Computer 2 connector on the
projector.
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the
yellow Video 3 connector on the projector.
Component video connection
Plug the white connector of a Mini-plug audio Y-cable into the left audio
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
the Audio In Video connector on the projector.
If your HD video device has component connectors, an optional
Component to VESA adapter can be used. Plug the component cable into
the video device. Plug the other end of the component cable into the adapter
and plug the adapter into the Computer 3 or Computer 2 connector.
Component offers the highest quality video output.
Keep in mind that video output from composite connections is not as high
quality as S-video.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video-out connector on the video device and into the HDMI connector on
the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3-
compatible source.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an S-
video cable into the S-video connector on your video device and into the
Video 2 connector on the projector. Use the audio cable as described above.
Keep in mind that S-video delivers higher quality video output than
composite.
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Shutting down the projector
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the
projector. The image returns when an active source is detected or a remote
or keypad button is pressed.
Table 3: Status indicator light behavior and meaning
Screen Save Time
You can make the black screen appear after a preset number of minutes by
Icon
Meaning
Power, solid amber
The projector is plugged in.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction
with the projector is performed for 30 minutes. By default, this feature is off.
Power, blinking green
The power button has been pressed and
the software is initializing.
Power, solid green
The projector is on and initialized.
Turning off the projector
Power, blinking amber
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 1 minute while the fans
continue to run to cool the lamp. When the lamp has cooled, the LED lights
amber and the fans stop. Unplug the power cable to completely power off
the projector.
Thermometer
The projector is too hot. Make sure the
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
service.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
support to contact service.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Problem
Solution
Result
No start up screen
Correct image
Plug power cord into the projector
press power button
Startup
Screen
If your computer is using the projector's DisplayLink
connector, see the DisplayLink User's Guide for
troubleshooting information.
Computer image projected
Only start up screen appears
Startup
Screen
Press the Source button
activate laptop’s external port
A
A
A
Restart laptop
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
Prolem
Solution
Result
Press the Auto Image button on keypad adjust computer
refresh rate in Control Panel > Display > Settings > Advanced
> Adapter (location varies by operating system)
No computer image, just the words “Signal out of
range”
Computer image projected
A
Signal out of
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image fuzzy or
cropped”
If your computer is using the DisplayLink connector, use
DisplayLink Manager software to change the display mode from
Extended Desktop to Duplicated Desktop. See the DisplayLink
Manager User's Guide for more information.
Only my laptop’s background appears, not the
Desktop icons
Background and Desktop projected
Disable “Extend my Windows Desktop” in Control Panel >
Display > Settings > Display 2 (location varies by operating
system)
A
A
A
A
Uncheck this
option, then
click Apply
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
Prolem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor or turn-
on dual-display
mode
Image not centered on screen
Move projector, adjust zoom, adjust height
Correct image
Adjust horizontal or
vertical position in
Advanced Picture
menu
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
Prolem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
Image does not fit 4:3 or 16:9 screen
Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect ratio menu
Correct image
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
Prolem
Solution
Result
Image upside down
Turn off Ceiling Mount in Setup menu
Correct image
A
A
Image reversed left to right
Turn off Rear Project in Setup menu
Correct image
Projected colors don’t match source
Adjust color, tint, brightness, contrast in the Basic
Picture menu
Correct image
COLOR
Download from Www.Somanuals.co2m0. All Manuals Search And Download.
Prolem
Solution
Result
The video embedded in my PowerPoint presentation If your computer is using the projector's DisplayLink
Embedded video plays correctly
does not play on the screen
connector, see the DisplayLink User's Guide for video
troubleshooting information.
Turn off the internal LCD display on your laptop
A
B
A
B
A
B
Lamp won’t turn on, Temperature light is on
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Startup
Screen
Temperature light
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
Prolem
Solution
Result
Lamp turns on
“Replace lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
Startup
Screen
lamp door
Lamp light
replace lamp
Still need assistance?
Check out our HOW TO section there for additional information on using
this projector for home theater or gaming applications. See the Quick Start
Poster/Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
Download from Www.Somanuals.co2m2. All Manuals Search And Download.
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by
removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an
environmentally proper manner.
navigation
buttons
To operate, point the remote at the front of the projector (not at the
computer). The range of optimum operation is about 15 feet (4.5m).
for shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
The remote also has a Source button to switch between sources.
The remote also has:
•
•
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank
•
•
•
•
•
•
Source button to switch between sources.
Blank button to blank the screen.
Mute button to silence the audio.
Auto Image button to resynch the projector to the source
Troubleshooting the remote
•
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the projector.
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
Using the audio
Using the projector’s speakers
connect audio cable
When the computer is using the DisplayLink connector, both audio and
video are sent over the USB cable to the projector and audio will play from
the projector's speakers.
For inputs other than DisplayLink, to use the projector's speakers, connect
the audio source to the Audio In Computer or Video connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
adjust volume
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for audio troubleshooting
information
•
•
Make sure the audio cable is connected to the correct Audio In
connector, Computer or Video.
Make sure the volume is turned up enough. Press the Volume button on
the keypad or remote.
•
•
Make sure the correct source is active.
Make sure that you are connected to an “audio out” connector on the
source as opposed to a “line-in” or “microphone” connector.
external speakers
with own power
source
•
•
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
speaker
cable
audio out
Connecting external speakers
The projector can be attached to external amplified speakers by connecting
a 3.5mm stereo audio cable from the Audio Out connector on the projector to
the amplified speakers. Alternatively, you can bypass the projector’s audio
system and connect the audio directly from your source to a stereo or home
theater system.
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
Optimizing computer images
After the projector is running and the image is on the screen, you can
optimize the image using the onscreen menus. For general information on
Presentation features
Several features are provided to make giving presentations easier. Here is
an overview, details are found in the menu section.
•
The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the
•
•
•
•
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
•
•
The Search Screen option lets you change the appearance of the blank
Change the Aspect Ratio. Choose the option that best fits your input
Two options, Auto Off and Screen Save Time, are provided to
automatically shut down the projector after several minutes of
inactivity or display a black screen. This helps preserve lamp life
Adjust the Color Temperature in the Advanced Picture menu
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for information about
optimizing images.
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
You can customize the projector for your specific setup and needs. See
•
•
For rear projection, turn Rear Project on in the Setup menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic
For ceiling mounted projection, turn Ceiling Mount on in the Setup
menu.
•
Change the Aspect Ratio. Choose the option that best fits your input
•
Specify which source the projector checks first for active video during
power-up.
•
•
•
•
•
•
•
•
•
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
Save settings for the active source as a preset.
Dynamic Messaging
You can use Command Line Interface (CLI) commands to display text
messages on the projector (for example, to display urgent alert messages to
employees). This requires a connection to the projector’s RS-232 serial
control connector. Go to our support website to download the RS-232
command reference for your projector.
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
Using the menus
keypad navigation
buttons
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use
the arrow buttons to move up and down to highlight the desired menu,
then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value or select an option or turn the
feature on or off. Press Select to confirm your changes. Use the arrows to
navigate to another setting. When your adjustments are complete, press
Menu to access a different menu; press the Menu button at any time to
navigate to the higher-level menu and ultimately close the menus.
The menus are grouped by usage:
•
•
The Basic Picture menu provides common image adjustments.
The Advanced Picture menu provides more complex image
adjustments.
•
•
The Setup menu provides set-up type adjustments that are not changed
often.
Basic Picture menu
Advanced Picture menu
The Status and Service menu provides information about the projector
and source.
Setup menu
Status and Service menu
Download from Www.Somanuals.co2m8. All Manuals Search And Download.
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Basic Picture menu
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video images.
The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch
enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 13.
Apply Preset...: Presets are provided that optimize the projector for
displaying computer presentations and video images under certain
conditions.
Aspect ratio
There is also a user-definable preset. To set this preset, adjust the image and
select Save User in the Presets menu. You can recall these settings in the
future by selecting the User preset.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Digital Zoom: changes the size of projector’s display area. If the display area
has been resized by this setting, it can be moved by changing the Horz Shift
and Vert Shift settings.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if its
size has been changed by the Digital Zoom setting.
increasing keystone
decreasing keystone
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
Advanced Picture menu
BrilliantColor™: produces an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images. Choose
Normal Look for most video sources and Bright Look for most computer
sources.
White Peaking: (video sources only) increases the brightness of whites that
are near 100%.
Color Temperature: changes the intensity of the colors. Select a listed relative
warmth value.
Advanced Picture menu
Force wide: when this is off, the analog locking algorithms choose the
standard mode resolution (4:3) as the preferred default resolution. When
this is on, the analog locking algorithms choose wide mode resolution
(16:10) as the preferred default resolution.
Overscan: removes noise around the video image.
Phase: adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Color Space: This option applies to computer and component video sources.
It allows you to select a color space that has been specifically tuned for the
input signal. When Auto is selected, the projector automatically determines
the standard. To choose a different setting, turn off Auto, then choose RGB
for computer sources or choose either REC709 or REC601 for component
video sources.
Gamma: select the appropriate gamma from among Video, Film, Bright, and
CRT.
Horizontal/Vertical Position: adjusts the position of a computer source.
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
Lamp Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter.
Setup menu
Language: allows you to select a language for the onscreen display.
Key Click: turns the key click sound on or off. When this setting is on,
pressing keys on the keypad causes the projector’s speaker to play a “click”
sound.
Power Sounds: controls whether the projector makes a sound when powered
on and off.
Auto Source: When this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this
feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by
pressing the Source button on the remote or keypad.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and
press Select to choose a different one.
•
•
•
Source Info: the default action. Shows the Source Info menu.
Projector Info: Shows the Projector Info menu.
page 29).
•
•
•
•
•
•
Overscan: removes noise around the image.
Blank Screen: displays an empty screen.
Freeze Screen: pauses the projected image.
Mute: turns off all sound.
Source: cycles through available sources.
Setup menu
Blank Key: Select what to display when the blank key on the remote is
depressed: your custom snapshot, a solid color screen (blue, black or white),
the factory logo screen, a timer, or test patterns. The timer option is useful
for classroom tests or break times during meetings.
Power-up Source: determines which source the projector checks first for
active video during power-up.
HDMI DDC: When this feature is set to On, the projector will support an
AC Power On: When this feature is on, the projector automatically turns on
when electrical power is connected. This allows control of ceiling mounted
projectors with a wall power switch.
older DVD player for HDMI port.
Video Standard: When this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives.
(The video standard options may vary depending on your region of the
world.) If the projector is unable to detect the correct standard, the colors
may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
the Video Standard menu.
Auto Off Time: automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Screen Save Time: automatically blanks the screen with a black color after no
signals are detected for a preset number of minutes. The image returns
when an active source is detected or a remote or keypad button is pressed.
Closed Captions: controls closed caption display while audio is not muted. If
this setting is not off, and audio is not muted, and the source is NTSC and
Download from Www.Somanuals.co3m1. All Manuals Search And Download.
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
press the Select button in order to access the “Wrong PIN” message and re-
enter the code.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the
startup screen. Enter the PIN. Use the navigation buttons on the remote or
keypad to enter the correct button press sequence. See the description above
for instructions.
Rear Project: reverses the image so you can project from behind a
translucent screen.
Auto Keystone: automatically adjusts vertical image.
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the
new PIN. You can navigate between OK and Cancel by pressing the up and
down buttons on the keypad. Select OK or Cancel by pressing the Select
button. Verify the new PIN.
Search Screen: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Take Snapshot...: Captures the current image and allows it to be used as the
search screen image.
If you lose or forget your custom PIN:
Show Messages: displays status messages (such as “Searching”) in the lower-
left corner of the screen.
Contact InFocus support. Go to www.infocus.com/support
Computer 2 SCART: Selects SCART connection type between RGB and
composite.
Menu Offset: allows you to change the position of the On Screen Display
items.
Serial Port, Baud Rate: selects the serial port and baud rate.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image
behind the menu is visible.
Serial Port Echo: controls whether the serial port echoes characters.
Magnify Controls: determines whether the select key can be used to change
magnify settings when the OSD menu is not visible.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image. The default PIN on this
projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the
remote or keypad to enter the correct 5-button press sequence. When all 5
numbers are entered correctly, press the Select button on the remote or
keypad to select OK. If the message “Wrong PIN” appears, verify the code
and re-enter it. If you mis-enter a number, you must enter 5 numbers and
Download from Www.Somanuals.co3m2. All Manuals Search And Download.
Status and Service menu
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings.
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info
menu to zero. Do this only after changing the lamp.
Factory Reset: restores all settings to their default.
Service Code: only used by authorized service personnel.
Status and Service menu
Download from Www.Somanuals.co3m3. All Manuals Search And Download.
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
Using the security lock
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on
how to use it.
security
lock
Download from Www.Somanuals.co3m4. All Manuals Search And Download.
•
Hg – Lamp contains mercury. Manage in accordance with local
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of
hours the lamp has been in use. Twenty hours before the lamp life expires,
the message “Replace lamp” appears on the screen at startup.
1 Turn off the projector and unplug the power cord.
2 Wait 60 minutes to allow the projector to cool thoroughly.
•
NOTE: Be sure to use the InFocus lamp module designed for this
areas), your retailer or your dealer. Only genuine InFocus lamps are tested
for use in this projector. Use of non InFocus lamps may cause electrical
shock and fire, and may void the projector warranty. InFocus is not
liable for the performance, safety or certification of any other lamps.
3 Remove the lamp door by: (a) removing the screw (labeled “1”) on the
side of the lamp door, (b) turning the lamp cover knob (labeled “2”)
counterclockwise to push up the lamp cover, and (c) lifting the door off.
turn off and unplug
projector
wait 60 minutes
WARNINGS:
•
The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
c
•
•
•
•
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can
obscure projection sharpness and may cause the glass to shatter.
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it.
•
•
Before replacing a ruptured lamp, clean the lamp compartment and
dispose of cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
b
a
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
4 Loosen the captive screws that attach the lamp housing to the projector.
Carefully remove the lamp housing. Dispose of the lamp in an
environmentally proper manner.
loosen screw
5 Install the new lamp module and tighten the screws.
6 Replace the lamp door by sliding it into place.
7 Plug in the power cord and press the Power button to turn the projector
back on.
8 To reset the lamp hour timer, navigate to the Status and Service menu and
Download from Www.Somanuals.co3m6. All Manuals Search And Download.
Customizing the projector 26
D
INDEX
DVDs 28
Numerics
A
F
G
H
I
Image
B
K
C
Connecting
L
Lamp hours, resetting 35
M
Connector on Projector 7, 8
O
Download from Www.Somanuals.co3m7. All Manuals Search And Download.
P
Presentation features 25
Projector
Source 30
T
Customization 26
U
V
W
R
Z
S
Safety Considerations 2
Download from Www.Somanuals.co3m8. All Manuals Search And Download.
|