Installation Guide
4 ports USB Net ShareStation
GUIP204
Part No. M1057
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
4
Disconnecting a USB device in Vista
Request to Disconnect in Vista
Setting the Polling Interval Widows -XP
Web Management Interface
Upload Firmware
36
37
39
40
44
45
46
47
48
49
About this Manual
5
Features
6
Package Contents
7
System Requirements
8
Physical Description
9
Reset Device
Hardware Installation
10
13
18
20
22
23
26
33
35
Factory Default
Software Installation - XP
Connecting to a USB device
Connecting to a USB Printer / Multifunction Printer
Disconnecting a USB device
Request to Disconnect
Password Change
FAQ
Federal Communications Commission (FCC)
Statement
CE Statement
Customer Support
Limited Warranty
Contact
51
52
53
54
Software Installation - VISTA
Connecting to a USB device in Vista
Connecting to a USB hard drive in VISTA
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing the IOGEAR GUIP204 4-ports USB Net ShareStation (hereafter referred to as
“USB Net ShareStation”). The USB Net ShareStation is designed to connect your All-In-One/Multifunction
devices, standard printers, and USB storage devices (hard drives, flash drives, and memory card readers)
to your network, allowing all network users access to these shared USB resources.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Manual
This manual provides introductory information as well as detailed instructions on how to set up and
manage the IOGEAR GUIP204 4-port USB Net ShareStation in various network environments.
To fully benefit from this document, you should be familiar with basic networking principles. The
instructions described in this manual are based on the settings in a new server. If needed, you can reset
the server back to the factory defaults. For details, please refer to the chapter “Restore Factory Defaults”.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
•
•
•
•
•
•
Share 4 USB devices through your home or office network
Wirelessly share your USB devices through your wireless router.
Share an external hard drive, flash drive or memory card reader with multiple users over your network
Share a USB webcam over a network
Enjoy music stored on any networked PC with a USB speaker*
Allows multiple users to share a Multi-Function Printer (MFP) over a network to print, scan, and fax
from any networked computer
•
•
•
•
Supported protocols:, LPR/LPD, DHCP, UPnP
Supports USB 2.0 and 1.1 devices
Supports Windows Vista Rally Technology
Works with any home or office Ethernet network
* Some USB devices require a direct connection for optimum performance
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
Verify that nothing is missing from the package by using the checklist below. Please contact your dealer
if anything is missing or damaged. All packing materials are recyclable. Please confirm the items in the
package below:
1 x 4-port USB Net ShareStation
1 x User Manual
1 x Software CD
1 x Power Adapter
1 x Warranty/Registration card
1 x RJ45 Ethernet Cable
7
Download from Www.Somanuals.com. All Manuals Search And Download.
System Requirements
Computer:
•
•
•
•
CPU of 1.7GHz and above
Minimum 512MB RAM
Windows XP/Vista
Available Ethernet port in home/office network
Support Devices:
•
•
•
•
•
•
•
•
Printer or Multi-function printer with USB connection*
External USB hard drive
USB speaker*
USB webcam*
USB flash drive
USB memory card reader
USB printer
USB scanner
Printer:
•
Multi-function printer with USB connection
* Some USB devices require a direct connection for optimum performance
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Physical Description
1. USB connection LED
2. USB port
3. Power Adapter Port
4. Network Port
5. Reset Button
6. USB ports
12Vdc
5A
Reset
Ethernet
1
2
3
4
5
2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
*Make sure that your USB devices are switched off and that the server’s power adapter is disconnected.
1. Connect your USB device to any one of the USB ports of the USB Net ShareStation.
12Vdc
5A
Reset
Ethernet
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Connect the USB Net ShareStation server to the router or switch with the included Ethernet cable.
12Vdc
5A
Reset
Ethernet
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connect the power adapter to the USB Net ShareStation server. The USB connection LED will turn on and the USB
Net ShareStation is correctly connected to the network.
12Vd
5A
Reset
Ethernet
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Installation - XP
1. Insert the Software CD into your computer. A splash screen should appear with a menu of options, including
the option to install the appropriate USB Net ShareStation software, access the User Manual, or Exit out of
the splash menu. To install the appropriate USB Net ShareStation software, click the installation button that
corresponds to the operating system that is installed on your computer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. The installation wizard will start the installation
process, select the language you like to install the
software as, then click “OK” to continue.
3. When the installation completes, click “Finish” to
close the installation wizard.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. On your desktop you will see a new IOGEAR icon
called “Launch IOGEAR Net ShareStation”,
double click the icon and it will bring up the IOGEAR
Net ShareStation server configuration utility.
5. Once the IOGEAR utility is launched Windows
will prompt you with a “Found New Hardware
Wizard” window. You will need to complete the
wizard so that you will be able to use the USB Net
ShareStation on your computer
Select “No, not this time” and click on ”Next” to
continue.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Windows will install the necessary drivers for the
USB Net ShareStation.
6. Click on “Install the software automatically
(Recommended)” and click on Next to continue.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Select Finish to complete the Found New
Hardware Wizard.
9. Once you are finished with the Found
New Hardware Wizard, the IOGEAR util-
ity will show up and display all the active
USB Net ShareStations connected on your
network. In this screen, you will see the
product listed as “IOGEAR GUIP204 – 567890
(192.168.10.59)”. The “567890” is the last 6
digits of the device’s MAC address, and the
“192.168.10.59” is the device’s IP address.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a USB device
1. Connect the USB cable on your USB device to one
of the USB ports on the USB Net ShareStation, and
make sure both the USB device and the USB Net
ShareStation are powered on. The USB device will
then show up on the IOGEAR Net ShareStation
utility underneath the “IOGEAR GUIP204..” as a
GREEN icon
. The green icon indicates that the
USB device is ready to be connected. If for any
reason the USB device does not show up, please
click the “Search” button to refresh the control center.
Note: If your USB device does not show up on
the list, please try to disconnect and reconnect
the device to the GUIP204. Also, please make
sure the GUIP204 and your USB device are
powered on.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Once the device has been connected, the GREEN
icon will turn ORANGE to indicate that the
2. Select the USB device that you will want to connect
and click on the “Connect” button at the bottom
connection has been established. The USB device
now becomes available on your computer, and you
can use this USB device as if it was directly
connected to your computer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a USB Printer / Multifunction Printer
1. Connect the USB cable on your printer or multi
function printer to the IOGEAR GUIP204 and make
sure your printer is powered on. You will then see
the connected printer show up in the IOGEAR Net
ShareStation utility underneath the “IOGEAR
GUIP204…” Select the printer from the list and click
on the “Connect” button.
Note: If your USB device does not show up on
the list, please try to disconnect and reconnect
the device to the GUIP204. Also, please make
sure the GUIP204 and your USB device are
powered on.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. The printer will be detected as if it was plugged
directly into your computer.
3. If this printer is connected to your computer for the
first time, then you will need to complete the setup
wizard for the printer software and driver installation.
Please follow the wizard to setup the printer. Make
sure you have the correct CD or drivers for your
printer and follow the on-screen steps in the wizard.
Once the wizard is completed, you will be able to
use the printer as if it was directly connected to your
computer.
Note: Please refer to your printer user manual
on how to setup your printer on the computer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnecting a USB device
1. To disconnect a USB device, simply click on
the connected USB device on the list of the
utility software, and press the “Disconnect”
button. The device will then no longer stay
connected to your computer, however, you
may re-connect the USB device again once
the icon becomes GREEN
.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Request to Disconnect
1. If a USB device is being used by another
computer on your network, a RED icon
will be displayed in front of the device name.
You will not have the option to disconnect
the device, however, you may send a
courtesy message to request that the other
user disconnect/release the device.
2. To send the courtesy disconnect message,
right click on the USB device and select
“Request Disconnect”, as shown below.
A message will then be sent to the user
requesting that they disconnect from the
USB device.
NOTE: If the occupying user denies this
request, then you will not be able to send
any further requests to the same user for
5 minutes. This is to prevent any user from
flooding the occupying user with multiple
requests within a short period of time.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
The chart list below shows what each colored icon means in the configuration software.
USB device is available and ready to be connected
The device is not connected but has some type of problem such as out of ink
USB device has been established and is now connected
Error with USB device. Example: out of paper
USB device is in use by another user.
Problem with a USB device occupied by another user
Unsupported USB device
USB server is on a different network segment. USB device can not be connected. See page 49
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Installation - VISTA
1. Insert the Software CD into your computer.
A splash screen should appear with a
menu of options. Click on “Windows
Vista installation” to set up the USB Net
ShareStation on Windows Vista
2. Click OK to start the installation process
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3. During the driver installation a Windows Vista
security message will appear. Select “Install
this driver software anyway” to continue.
4. Click on Finish to complete the installation
process.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Once the installation process has been
completed you will need to go to the
Network window to configure the USB Net
ShareStation. To do so, click on the Vista
logo on the lower right corner of your screen
and select Network from the right hand side
of the menu.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The USB Net ShareStation icon will appear under other devices on the Network window. If the
USB Net ShareStation or any other network icons in the network window do not appear, then a
message will show up across the network screen indicating that Network Discovery is turned off.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
7. To turn Network Discovery on, right click on the message, then select “Turn on network
discovery and file sharing” from the list. Once Network Discovery has been enabled you will be
able to see the USB Net ShareStation icon under Other Devices.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Select “Yes, turn on network discovery and file sharing for all public networks”.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Click on the blinking window at the system
tray which is prompted by the “User
Account Control” permission window.
Click “Continue” to proceed with the
installation.
9. Right click on the USB Net ShareStation
“IOGEAR GUIP204…” icon, and select
“Install” to begin using the USB Net
ShareStation.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
11.After the driver installation has been
completed the “IOGEAR GUIP204…” icon
will change to a new product image. If the
new product image icon does not change,
press “F5” to refresh the Network window.
After driver installation the device icon will
change.
You are now ready to use the USB Net
ShareStation
Note: It is recommended to reboot your
computer after installation to ensure
optimal performance.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a USB device in Vista
1. After you have successfully installed the USB Net ShareStation driver, connect the USB cable of your
USB device into the USB port on the USB Net ShareStation, and make sure both the USB device and
the USB Net ShareStation are powered on.
2. When the USB device is connected, the USB Net ShareStation will detect the connection of the
device, and an icon of the device will show up in the Network window. In this example, we have
connected a Logitech USB speaker.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Right click on the USB device that you will want to connect and select “Connect” to establish the
connection. You will see the device driver is installing and the status will show at the bottom right
corner on your system tray. This message will go away once the drivers have been installed.
After the installation is completed, the USB device will become available as if it were directly connected to
your computer.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a USB hard drive in VISTA
1. Connect the USB cable of the USB hard
drive to the USB port on the USB Net
ShareStation, and make sure both the USB
hard drive and the USB Net ShareStation
are powered on. Right click on the device
icon and select Connect to connect to the
device. Then right click again on the device
icon and select “My Computer” to bring up
My Computer window. Or you may simply
double click the hard drive icon to bring up
My Computer window.
2. You will now see the external hard drive
become available as if it were directly
connected to your computer.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnecting a USB device in Vista
To safely disconnect a USB device under the Network window, right click the USB device icon and select
“Disconnect” from the menu. Once the USB device has been disconnected, it will no longer be connected
to your computer, and you can unplug the USB cable of the USB device from the USB Net ShareStation.
If you would like to reconnect the USB device, simply right click on the USB icon and select “Connect”
again to establish the connection.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Request to Disconnect in Vista
If you would like to use a USB device that is being occupied by another user you may send a courtesy
message asking the user to disconnect. You may do this by right clicking on the USB device icon that you
will like to use and selecting “Request Remote to Disconnect.” A message will then be sent to the user
requesting that they disconnect from the USB device.
NOTE: If the occupying user denies this request, then you will not be able to send any further request to
the same user for 5 minutes. This is to prevent any user from flooding the occupying user with multiple
requests within a short period of time.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: after a system reboot, you might
not be able to connect to any USB device
for a short period of time. When right
clicking on a device, you will see the
following message instead of the option to
“Connect.”
Depending on the performance of your
PC and the number of active USB Net
ShareStations on your network, it may
take up to 3 minutes for your computer
to recognize all USB Net ShareStation.
This is because VISTA needs time to
probe the entire network before it loads
the necessary driver to run the USB Net
ShareStation. Once the driver has been
loaded, the option to “Connect” to the
device will be made available when
right-clicking a device.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Polling Interval Widows -XP
The polling interval will allow the configuration
utility to pull information from your network to
find out the status of all the connected USB Net
ShareStations and USB devices. By default,
this feature is not automatically configured. You
may set a time so that the server will perform
the polling automatically. To configure the polling
interval, in the IOGEAR USB Server utility, click
on File -> Settings -> Polling Interval.
You may set a number from 1 – 60 in the
“Seconds” box. Click on “Submit” to allow the
new interval setting to take effect. Once you
have set a number the utility will automatically
update any changes made to server in the main
dialog box.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Web Management Interface
8. To access web management interface in XP,
in the IOGEAR Net ShareStation utility, select
the USB Server on the list, and click on the
“Config” button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
2. To access web management interface in
VISTA, in the Network window, right click on
the “IOGEAR GUIP204…” icon, and select
“View device webpage.”
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The left panel of the web management interface provides a list of different options to choose from.
Device Status: Displays the current USB device info and will tell you which computer a USB device is
connected to. The interface is limited to support up to 4 USB devices.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Network: You can change the network settings according to your network specifications. If you would
like to give the USB Net ShareStation a static IP address, you will need to Disable DHCP in the “DHCP
Setting” menu. Once DHCP is disabled, enter the desired IP address on the IP address field along with
the subnet mask and click the “Submit” button to reboot the USB Net ShareStation. Please note that if
the USB Net ShareStation has a set password, you will need to enter it into the password field box.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Upload Firmware
The firmware link will allow you to upload the latest firmware on the USB Net ShareStation server. Click on
“Browse” to specify the firmware location on your PC. Once the location path of the firmware has been
set, click “Submit” to begin the update.
Please note that if the USB Net ShareStation has a set password, you will need to enter it into the
password field box.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset Device
The Reset Device window will allow you to reboot the USB Net ShareStation server. Please note that if the
USB Net ShareStation has a set password, you will need to enter it into the password field box.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Default
Allows you to restore the USB Net ShareStation back to factory default. Please note that if the USB Net
ShareStation has a set password, you will need to enter it into the password field box.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Password Change
You can add or change an existing password on the USB Net ShareStation in this window. By default
the USB Net ShareStation does not come with a default password.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
FAQ
1. How come I cannot connect to my USB device to my computer through the USB Net
ShareStation?
• Make sure the USB device functions normally when you plug it into your PC via USB cable.
• If the USB device, such as USB printer or multi-function printer, requires a driver, please make sure you
have installed it on the computer you wish to use. Rebooting your PC after installing USB device driver
might also help.
• Although the USB Net ShareStation could work with a very wide spectrum of USB devices, it still has
limited support on some USB devices. Please refer to the supported device list for details.
2. How come I cannot see any servers on my IOGEAR USB Server listing window after installing it?
Please make sure that all of your USB Net ShareStations are correctly connected to your network. Also,
certain anti-virus programs come with firewall functions that might prevent the USB Net ShareStation
utility from accessing the network. Please make sure USB Net ShareStation utility is not being blocked
by your anti-virus program.
3. The connected USB devices are disconnected after my PC wakes up from Standby?
The connected devices will automatically be released for other users in case you forget to release them.
Please reconnect the USB devices again after your PC “wakes up.”
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of
the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
CE Statement
This device has been tested and found to comply with the requirements set up in the council directive
on the approximation of the law of member states relating to EMC Directive 89/336/EEC, Low Voltage
Directive 73/23/EEC and R&TTE Directive 99/5/EC.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support
Should you require any technical assistance, call toll-free: 866-9-IOGEAR (866-946-4327) or visit our
subject to change without prior notice.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK
OR ITS DOCUMENTATION EXCEED THE PRICE PAID FOR THE PRODUCT.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the
contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or
fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or documentation without obligation
to notify any individual or entity of such revisions, or updates. For further inquires please contact your direct
vendor.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact
IOGEAR, INC.
23 Hubble
Irvine, CA 92618
P 949.453.8782
F 949.453.8785
© 2008 IOGEAR. All Rights reserved. Part No. M1057
IOGEAR, the IOGEAR logo, are trademarks or registered trademarks of IOGEAR, Inc. Microsoft and Windows are regis-
tered trademarks of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks
of their respective holders. IOGEAR makes no warranty of any kind with regards to the information presented in this
document. All information furnished here is for informational purposes only and is subject to change without notice.
IOGEAR, Inc. assumes no responsibility for any inaccuracies or errors that may appear in this document.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
About Us
FUN
IOGEAR offers connectivity solutions that are innovative, fun, and stylish,
helping people enjoy daily life using our high technology products.
GREEN
IOGEAR is an environmentally conscious company that emphasizes the
importance of conserving natural resources. The use of our technology
solutions helps reduce electronic waste.
HEALTH
IOGEAR supports healthy and fit lifestyles. By integrating products with the
latest scientific developments, IOGEAR’s solutions enhance the life of end-
users.
© 2008 IOGEAR, INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|