| Start Here   ® Epson Stylus CX6600   1 1 Unpack   Make sure you have all the parts shown here. If any parts are missing,   contact Epson® as described on the back of this sheet.   Epson Stylus CX6600   Software   CD-ROM   Quick Guide   Paper support   Ink cartridges   Feeder guard   2 3 Remove all the blue packing tape from the printer.   Caution: Do not remove the yellow sticker until instructed.   Lift up the scanner.   4 Peel off the tape from the ink cartridge holder.   5 Close the scanner section.   2 1 Attach the Parts   Insert the paper support into the slots behind the printer, as shown.   2 Lower the feeder guard into the slots behind the scanner lid.   (Insert the hinges on the feeder guard into the corresponding   slots on the printer.)   3 1 Plug In and Turn On   Plug the Stylus CX into a grounded electrical outlet.   2 Press and hold the On button until the green lights come on.   On button   4 Install Ink Cartridges   Wait until you see “Initial Charge” displayed on the LCD screen.   Lift up the scanner.   1 2 3 Shake the package of ink cartridges four or five times.   Then remove the cartridges from the package.   Don’t touch the green part   Caution: You must install all the cartridges and leave them installed   for all types of printing. To avoid damaging the Stylus CX, never   move the print head by hand.   4 5 6 Open the ink cartridge cover.   Place each cartridge, one at a time, in its holder.   Press down on each cartridge until it clicks into place.   continue   7 Close the ink cartridge cover, then close the scanner.   The Stylus CX begins charging the ink delivery system.   Charging takes about 2 minutes. The Stylus CX makes various   sounds and “Charging . . .” appears on the LCD screen. Don’t turn   it off while “Charging . . .” appears, or you’ll waste ink.   5 1 Load Paper   Extend the output tray.   2 Slide the edge guide to the left.   3 Place a stack of paper against the right side of the sheet feeder,   but don’t push it in. Slide the edge guide against the paper.   Turn over   6 Install Software and   Connect to Your Computer   The software works with Windows® 98SE, Me, 2000, and XP, and Macintosh®   OS 9.1.x to 9.2.x and 10.2.x to 10.3.x. Follow the steps below (for Windows),   or the steps in the next column (for Macintosh).   Note: There is a Security Lock program on your software CD-ROM that lets   you prevent unauthorized use of your CX6600. See the Quick Guide for   instructions on installing and using it.   Windows   1 Make sure the Stylus CX is not   connected to your computer,   then turn on your computer.   Note: If you see several New   Hardware Wizard screens, click   Cancel for each of these screens and   disconnect your Stylus CX. You can’t   install your software that way.   2 3 Insert your Stylus CX software CD-ROM in your CD-ROM or DVD drive.   Wait until you see this screen,   then click Install.   Note: If you don’t see this screen,   do the following:   For Windows XP: click Start >   My Computer. Then double-click   the Epson CD-ROM icon.   For Windows 98/Me/2000: double-click   My Computer.   Then double-click theEpson CD-ROM icon.   4 5 Read the license agreement, then click Agree. Several messages   display on your screen.   When you see this screen, make sure   your Stylus CX is turned on, then lift   up the scanner.   6 Remove the yellow   sticker and plug the   square end of the USB   cable into the USB port   on your Stylus CX.   Then route the cable in   the slot as shown.   Caution: Make sure the USB cable fits securely into the slot. The USB   connector may snap if the cable is not routed correctly in the slot and   the scanner is closed with force.   7 8 Close the scanner carefully.   Plug the flat end of the   cable into any available   USB port on your   computer.   9 Click Next and follow the   instructions on the screen to install   more software.   Note: It will take several minutes to install the software.   Don’t cancel the installation.   10 At the completion screen, print a test page, if desired. When done,   click Next to install additional software.   11 Follow the instructions on the screen to install additional software.   When done, click Exit.   12 When you see the Product Registration screen, register your Stylus CX   as instructed, then remove the CD-ROM and restart your computer.   Now you’re ready to copy, scan, and print. See the Quick Guide or your   on-screen CX6600 Reference Guide for instructions.   Macintosh   1 Insert your Stylus CX software CD-ROM into your CD-ROM   or DVD drive.   2 Double-click the   CD-ROM icon, if necessary. Then   double-click the Epson installer   Epson   icon. You see this screen:   3 4 Click Install.   Read the license agreement, then   click Agree.   Note: If you’re installing on Macintosh OS X, enter your   administrator name and password, if necessary.   5 6 For Macintosh OS X: Continue with the following steps.   For Macintosh OS 9: Follow any on-screen instructions,   then continue with step 9.   Click Install at the EPSON Scan   Installer screen to install the   scanner portion of your software.   7 8 When the software finishes installing,   you see this screen. Click Quit.   Follow the on-screen instructions to   install additional software.   Note: Click Quit when each part finishes installing.   9 When installation is complete, you see the Additional Software screen.   Follow the instructions on the screen to install the software. When   done, click Exit.   10 When you see the Product Registration   screen, register your Stylus CX as   instructed, then remove the CD-ROM   and restart your Macintosh.   11 Make sure your Stylus CX is turned on,   then lift up the scanner.   12 Remove the yellow   sticker and plug the   square end of the USB   cable into the USB port   on your Stylus CX. Then   route the cable in the slot   as shown.   Caution: Make sure the USB cable fits securely into the slot. The USB   connector may snap if the cable is not routed correctly in the slot and   the scanner is closed with force.   13 Close the scanner carefully.   14 Plug the flat end   of the cable into   any available USB   port on your   Macintosh.   Follow the instructions below to add the Stylus CX to the   Print Center or Printer Setup Utility (for OS X) or the Chooser (for OS 9).   ® Selecting the Stylus CX for Mac OS X   1 Open the OS X Applications folder, then open the Utilities folder and   start Print Center or the Printer Setup Utility.   If you see this screen, click Add.   2 3 4 On the Printer List screen, click the   Add button.   On the next screen, select EPSON USB from   the pop-up menu.   Click Stylus CX6600.   Note: If the CX6600 doesn't appear, make   sure it is turned on and securely connected   to your Macintosh.   5 6 Click the Add button. You see the Stylus CX6600 in the Printer List.   Quit Print Center or the Printer Setup Utility. Now you’re ready to copy,   scan, and print. See the Quick Guide or your on-screen CX6600   Reference Guide for instructions.   7 If you use Classic Mode applications, install the software on OS 9 also.   Selecting the Stylus CX for Mac OS 9   1 2 Open the Chooser from the Apple® menu.   Select CX6600 Series, then select   your USB port and turn on   background printing.   3 Close the Chooser. Now you’re   ready to copy, scan, and print. See   the Quick Guide or your on-screen   CX6600 Reference Guide for   instructions.   Any Problems?   If the red ! error light is on, check the message on the Stylus CX. Try   turning the Stylus CX off and then back on to clear the error. If your   problem is listed here, try these suggestions. For more information, see   your Quick Guide, software Help, or on-screen CX6600 Reference Guide.   The Found New Hardware   Wizard appears on   your screen.   Click Cancel and follow the steps in   section 6. Disconnect the Stylus CX   before installing the software.   You see an error message   when you try to print   or scan.   Make sure your Stylus CX is connected to   your computer, plugged into a power   source, and turned on.   The Stylus CX   doesn’t work.   Make sure you removed the tape from the ink   cartridge holder, as described in section 1.   Turn the Stylus CX off and then on again.   Make sure the ink cartridges are pushed   all the way down.   Check the LCD screen to see if you or   someone else set the Security Lock. See   your Quick Guide for details.   Make sure your Epson Stylus CX6600   software is installed correctly.   Any Questions?   Here’s where to look for answers:   Epson Stylus CX6600 Quick Guide   On-screen Reference Guide   Double-click the CX6600 Reference Guide icon on your   desktop to view your Reference Guide.   On-screen help for EPSON Smart Panel™, ArcSoft PhotoImpression™,   ® ® EPSON Scan, and ABBYY FineReader Sprint   Click the Help button or question mark that appears on the screen   when you’re using any of these programs.   Epson Technical Support (Stylus CX6600 and EPSON Scan)   • World Wide Web   • Automated Telephone Services   To use these services, you must have a touch tone telephone and call   (800) 922-8911. Your Epson SoundAdviceSM Express Code is 70575.   Use this code to quickly select your product in SoundAdvice.   • To speak to a Technical Support Representative   Dial (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM,   Pacific Time, Monday through Friday. Toll or long distance charges   may apply.   Software Technical Support   Software   Telephone and Fax   Internet and E-mail   EPSON Smart   Panel   (510) 445-8616   Fax: (510) 445-8601   ArcSoft   PhotoImpression   (510) 440-9901   8:30 AM to 5:30 PM,   Pacific Time,   Monday–Friday   Fax: (510) 440-1270   ABBYY   (510) 226-6719   FineReader Sprint   Fax: (510) 226-6069   Need Paper and Ink?   For the best prints and copies, use genuine Epson ink and paper. You can   buy them from your local retailer or from the Epson StoreSM at (800) 873-7766,   (800) 463-7766 for dealer referral.   Look for these cartridges and paper:   T0441   T0431   High   Capacity Ink   T0442   Cyan   T0443   Magenta Yellow   Ink Ink   Black Ink Cartridge Cartridge Cartridge   T0444   Standard   Capacity   Black Ink   Cartridge Cartridge   Premium Bright White Paper   Ultra-smooth white paper perfect for everyday   use—especially two-sided documents.   ® DURABrite Ink Glossy Photo Paper   Heavier weight paper for long-lasting enlargements   and snapshots.   Double-Sided Matte Paper   The ideal paper for high quality printing of   brochures, newsletters, or flyers.   Epson and Epson Stylus are registered trademarks and EPSON Smart Panel is a trademark   of Seiko Epson Corporation. DURABrite is a registered trademark, and Epson Store and   SoundAdvice are service marks of Epson America, Inc.   General Notice: Other product names used herein are for identification purposes only and may be   trademarks of their respective owners. Epson disclaims any and all rights in those marks.   © 2004 Epson America, Inc. 5/04   Printed in XXXXXX XX.XX-XX   CPD-18233   |