Grizzly Trimmer H2867 User Manual

ELECTRIC SHEAR  
MODEL H2867  
INSTRUCTION MANUAL  
COPYRIGHT © NOVEMBER, 2001 BY GRIZZLY INDUSTRIAL, INC.  
1821 VALENCIA ST., BELLINGHAM, WA 98227  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
PRINTED IN CHINA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
For Your Own Safety Read Instruction Manual  
Before Operating This Equipment  
The purpose of safety symbols is to attract your attention to possible hazardous  
conditions. This manual uses a series of symbols and signal words which are  
intended to convey the level of importance of the safety messages. The progres-  
sion of symbols is described below. Remember that safety messages by them-  
selves do not eliminate danger and are not a substitute for proper accident pre-  
vention measures.  
Indicates an imminently hazardous situation which, if  
not avoided, WILL result in death or serious injury.  
Indicates a potentially hazardous situation which, if  
not avoided, COULD result in death or serious injury.  
Indicates a potentially hazardous situation which, if  
not avoided, MAY result in minor or moderate injury.  
It may also be used to alert against unsafe practices.  
This symbol is used to alert the user to useful information  
about proper operation of the equipment.  
NOTICE  
Safety Instructions For Power Tools  
5. KEEP CHILDREN AND VISITORS  
AWAY. All children and visitors  
should be kept a safe distance from  
work area.  
1. KEEP ALL SAFETY DEVICES IN  
PLACE and in working order.  
2. REMOVE ADJUSTING KEYS AND  
WRENCHES. Form habit of check-  
ing to see that keys and adjusting  
wrenches are removed from tool  
before operation.  
6. MAKE  
WORKSHOP  
CHILD  
PROOF with padlocks, master  
switches, or by removing starter  
keys.  
3. KEEP WORK AREA CLEAN.  
Cluttered areas and benches invite  
accidents.  
7. DO NOT FORCE TOOL. It will do  
the job better and safer at the rate  
for which it was designed.  
4. DO NOT USE IN DANGEROUS  
ENVIRONMENT. Do not use power  
tools in damp or wet locations, or  
where any flammable or noxious  
fumes may exist. Keep work area  
well lighted.  
8. USE THE RIGHT TOOL. Do not  
force tool or attachment to do a job  
for which it was not designed.  
9. DO NOT USE UNDER THE INFLU-  
ENCE OF DRUGS OR ALCOHOL.  
H2867 Electric Shear  
-1-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Instructions For Power Tools  
10. USE PROPER EXTENSION CORD  
15. MAINTAIN TOOLS WITH CARE.  
Keep tools sharp and clean for best  
and safest performance. Follow  
instructions for lubricating and  
changing accessories.  
for the tool. Make sure your extension  
cord is in good condition. Conductor  
size should be in accordance with the  
chart below. The amperage rating  
should be listed on the motor or tool  
nameplate. An undersized cord will  
cause a drop in line voltage resulting  
in loss of power and overheating.  
Your extension cord must also con-  
tain a ground wire and plug pin.  
Always repair or replace extension  
cords if they become damaged.  
16. DISCONNECT TOOLS before ser-  
vicing and changing accessories.  
17. REDUCE THE RISK OF UNINTEN-  
TIONAL STARTING. Make sure  
switch is in off position before plug-  
ging in.  
18. USE  
THE  
RECOMMENDED  
Consult the  
ACCESSORIES.  
owner’s manual for recommended  
accessories. The use of improper  
accessories may cause risk of injury.  
Minimum Gauge for Extension Cords  
AMP  
RATING  
0-6  
LENGTH  
50ft  
16  
25ft  
18  
18  
16  
14  
12  
10  
100ft  
16  
14  
14  
12  
19. CHECK DAMAGED PARTS. Before  
further use of the tool, a guard or  
other part that is damaged should be  
carefully checked to determine that it  
will operate properly and perform its  
intended function. Check for align-  
ment of moving parts, binding of  
moving parts, breakage of parts,  
mounting, and any other conditions  
that may affect its operation. A guard  
or other part that is damaged should  
be properly repaired or replaced.  
7-10  
16  
16  
12  
12  
11-12  
13-16  
17-20  
21-30  
10  
No  
10  
11. WEAR PROPER APPAREL. Do not  
wear loose clothing, gloves, neckties,  
rings, bracelets, or other jewelry  
which may get caught in moving  
parts. Non-slip footwear is recom-  
mended. Wear protective hair cover-  
ing to contain long hair.  
20. NEVER LEAVE TOOL RUNNING  
UNATTENDED. Turn the power off,  
and do not leave tool until it comes to  
a complete stop.  
12. ALWAYS USE SAFETY GLASSES.  
Also use face or dust mask if cutting  
operation is dusty. Everyday eye-  
glasses only have impact resistant  
lenses, they are NOT safety glasses.  
21. NEVER ALLOW UNTRAINED  
USERS TO RUN THIS TOOL  
WHILE UNSUPERVISED.  
13. SECURE WORK. Use clamps or a  
vise to hold work when practical. It is  
safer than using your hand and frees  
both hands to operate tool.  
22. IF YOU ARE UNSURE OF THE  
INTENDED OPERATION, STOP  
USING THE TOOL. Seek formal  
training or research books or maga-  
zines that specialize in power tools.  
14. DO NOT OVERREACH. Keep proper  
footing and balance at all times.  
-2-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Most importantly, we stand behind our  
Commentary  
tools. If you have any service questions or  
parts requests, please call or write us at  
the location listed below.  
We are proud to offer the Grizzly Model  
H2867 Electric Shear. This model is part  
of a growing Grizzly family of fine power  
tools. When used according to the guide-  
lines set forth in this manual, you can  
expect years of trouble-free, enjoyable  
operation and proof of Grizzly’s commit-  
ment to customer satisfaction.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail: techsupport@grizzly.com  
5
This shear features a 2.4 amp motor, 32"  
width of cut and 4500 strokes/min, cuts up  
to 116" mild steel, 364" stainless steel, is  
double insulated, 110V and weighs 312  
lbs.  
We are pleased to provide this manual  
with the Model H2867. It was written to  
encourage safety considerations and  
guide you through general operating pro-  
cedures and maintenance. This manual  
represents our effort to produce the best  
documentation possible.  
The specifications, details, and pho-  
tographs in this manual represent the  
Model H2867 as supplied when the manu-  
al was prepared. However, owing to  
Grizzly’s policy of continuous improve-  
ment, changes may be made at any time  
with no obligation on the part of Grizzly. If  
you have any comments regarding this  
manual, please write to us at the address  
below:  
Read the manual before assembly  
and operation. Become familiar with  
this tool, its safety instructions, and  
its operation before beginning any  
work. Serious personal injury may  
result if safety or operational infor-  
mation is not understood or followed.  
Grizzly Industrial, Inc.  
Technical Documentation  
P.O. Box 2069  
C
/O  
Bellingham, WA 98227-2069  
-3-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Figure 1. Setting gap with shims.  
Operating this shear can propel  
objects into the air, causing immedi-  
ate eye damage. To protect yourself,  
always wear American National  
Standards Institute (ANSI) approved  
safety glasses or goggles when oper-  
ating this equipment. To protect your  
hands, always wear leather hand pro-  
tection when operating this shear.  
Test Run  
Your Model H2867 has a slide style  
ON/OFF switch as shown in Figure 2.  
Before performing any cutting operations,  
turn the shear ON and listen for any  
unusual noises. If everything appears to  
be in working order, you are ready to begin  
cutting.  
Adjustments  
Your Model H2867 includes a set of three  
thickness shims: 0.005", 0.008" and  
0.013". These shims are used to set the  
gap size between the side of the shear jaw  
and the moving cutter. Depending on the  
thickness of the material you intend to cut,  
one of the three thickness shims is used to  
set the desired gap. The following is a gen-  
eral guideline for correct adjustment:  
Sheet Metal  
• 25 Gauge  
• 19 Gauge  
• 16 Gauge  
Shim  
0.005"  
0.008"  
0.013"  
Figure 2. ON/OFF switch.  
Use the supplied Allen® wrench to adjust  
the gap of the cutting jaws as shown in  
Figure 1.  
-4-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
If you are cutting a large dimension of  
sheet metal, use a large flat working sur-  
face such as a workbench to support the  
work as shown in Figure 3. Once the cut  
lines have been determined, turn the  
shears ON and begin the cut.  
Figure 3. Cutting large stock.  
If you need to trim small pieces of sheet  
metal, use the shear in a stationary posi-  
tion while pulling the metal through the  
shears, towards your body as shown in  
Figure 4. Avoid letting your fingers get to  
close to the moving jaws.  
If everything is in proper adjustment and  
working order, there should be a spiral trail  
of sheet metal exiting the shear as you  
make your cut.  
Figure 4. Cutting small stock.  
-5-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Slide the old brushes out of the slots and  
Oiling Shear  
replace with the fresh set as shown in  
Figure 7. Screw the caps back into the  
shear body and the shear is ready for use.  
Periodically oil your new Grizzly shear to  
help maintain its useful life. Place one drop  
of light machine oil in the shear jaws (as  
shown in Figure 5) before every use. Wipe  
off any excess oil to avoid dust build-up.  
Figure 7. Replacing brushes.  
Cleaning Shear  
Use a good solvent to clean the jaw  
assembly of the shear. Avoid getting sol-  
vent on the plastic body of the shear as it  
may damage the plastic. Always be sure  
that the shear is dry before using it again.  
Figure 5. Lubricating shear.  
Changing Brushes  
Over time, the motor brushes will become  
worn and loaded with carbon deposits.  
This will dramatically lower the perfor-  
mance of the electrical motor.  
Do not allow dust, chips, sand, etc. into the  
air vent holes. This could lead to motor fail-  
ure and premature bushing failure.  
An extra pair of brushes has been includ-  
ed. To change the brushes, unscrew the  
small caps on the sides of the shear body  
as shown in Figure 6.  
Never use use gasoline or other flam-  
mable liquids to clean this tool.  
Vapors in the tool may ignite, causing  
the tool to explode. Ignoring this  
warning may lead to serious personal  
injury or even death!  
Figure 6. Removing brushes.  
-6-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
-7-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY AND RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original  
purchaser from the date of purchase. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-  
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be  
implied by law, including any merchantability or fitness, for any particular purpose, are here-  
by limited to the duration of this written warranty. We do not warrant or represent that the  
merchandise complies with the provisions of any law or acts unless the manufacturer so  
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price  
paid for the product and any legal actions brought against Grizzly shall be tried in the State  
of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, con-  
tingent, special, or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details.  
We will then issue you a “Return Authorization Number,” which must be clearly posted on  
the outside as well as the inside of the carton. We will not accept any item back without this  
number. Proof of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they con-  
stantly strive to achieve better quality equipment. We make every effort to ensure that our  
products meet high quality and durability standards and we hope you never need to use this  
warranty.  
Please feel free to write or call us if you have any questions about the machine or the man-  
ual.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail:  
Thank you again for your business and continued support. We hope to serve you again  
soon!  
-8-  
H2867 Electric Shear  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY CARD  
Name__________________________________________________________  
Street__________________________________________________________  
City____________________State________Zip_________  
Phone Number____________E-Mail___________________FAX____________  
Model #___________________________ Order #_______________________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help  
us develop better products and services. Of course, all information is strictly confidential.  
9. How many of the machines checked above are  
Grizzly? ____________  
1. How did you learn about us?  
___Advertisement  
___Friend  
___Catalog  
___World Wide Web  
___Other__________________________  
___Card Deck  
10. Which portable/hand held power tools do you own?  
Check all that apply.  
___Belt Sander  
___Biscuit Joiner  
___Circular Saw  
___Detail Sander  
___Drill/Driver  
___Orbital Sander  
___Palm Sander  
___Portable Planer  
___Saber Saw  
___Reciprocating Saw  
___Router  
2. What is your annual household income?  
___$20,000-$29,999  
___$30,000-$39,999  
___$40,000-$49,999  
___$50,000-$59,999  
___$60,000-$69,999  
___$70,000-$79,999  
___$80,000-$89,999  
___$90,000 +  
___Miter Saw  
___Other_________________________________  
3. What is your age group?  
___20-29  
11. What machines/supplies would you like Grizzly  
Industrial to carry?  
___50-59  
___60-69  
___70 +  
___30-39  
___40-49  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
4. How long have you been a woodworker?  
___0 - 2 Years  
___2 - 8 Years  
___8 - 20 Years  
___20+ Years  
12. What new accessories would you like Grizzly  
Industrial to carry?  
5. How would you rank your woodworking skills?  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
___Simple  
___Advanced  
___Intermediate  
___Master Craftsman  
6. What stationary woodworking tools do you own?  
Check all that apply.  
13. What other companies do you purchase your tools  
and supplies from?  
___Air Compressor  
___Band Saw  
___Panel Saw  
___Planer  
_________________________________________  
_________________________________________  
_________________________________________  
___Drill Press  
___Power Feeder  
___Radial Arm Saw  
___Shaper  
___Jointer  
___Lathe  
___Drum Sander  
___Dust Collector  
___Spindle Sander  
___Table Saw  
14. Do you think your purchase represents good value?  
___Yes  
___No  
___Mortiser  
___Wide Belt Sander  
___Horiz.Boring Machine  
___Vacuum Veneer Press  
___Other______________________________  
15. Would you recommend Grizzly to a friend?  
___Yes ___No  
16. Would you allow us to use your name as a refer-  
ence for Grizzly customers in your area? Note: We  
never use names more than three times.  
7. How many of your woodworking machines are  
Grizzly? _____________  
___Yes  
___No  
8. Which benchtop tools do you own? Check all  
that apply.  
17.Comments:________________________________  
_________________________________________  
_________________________________________  
_________________________________________  
___1"x42" Belt Sander ___6" - 8" Grinder  
___5" - 8" Drill Press ___Mini Lathe  
___8" Table Saw  
___Scroll Saw  
___8" - 10" Bandsaw  
___Disc/Belt Sander  
___Spindle/Belt Sander ___Mini Jointer  
___10"-12"Thickness Planer  
___Other______________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Send a Grizzly Catalog to a friend:  
Name________________________________  
Street________________________________  
City______________State______Zip_______  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Swing Sets Swing Set User Manual
Grundig Flat Panel Television 22 VLE 8120 BG User Manual
Haier Range KGG5201 A1 User Manual
Hamilton Beach Coffeemaker 49995 User Manual
Hamilton Beach Coffeemaker Commercial coffeemaker User Manual
Hotpoint Oven GP641X User Manual
Hotpoint Washer HY6F3551 User Manual
HP Hewlett Packard Network Card DA 10852 User Manual
HP Hewlett Packard Speaker 4286A User Manual
HP Hewlett Packard TV Cables 11581A User Manual