T3643
Infant Seat
Infant Swing
Toddler Seat
High Chair
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information
High Chair
• Age: approximately 6-24 months.
• Maximum weight: 50 lbs (22,6 kg).
• Use high chair only with a child who has enough upper body control to sit up unassisted.
WARNING
To prevent serious injury or death from falls or sliding out:
• Always secure child with restraint belts adjusted to fit your child snugly. The tray is
not designed to hold child in high chair.
• Use only with a child who has enough upper body control to sit unassisted.
• Never leave child unattended.
• Never release seat from base with child in high chair. Never carry child in seat.
Toddler Seat
• Age: approximately 18 months and up.
• Maximum weight: 50 lbs (22,6 kg).
• Use toddler seat only with a child capable of getting into and out of the product unassisted.
WARNING
To prevent serious injury or death:
• Fall Hazard
- Never use on any elevated surface, since child’s movement may cause the product
to slide or tip over. Use only on a floor.
- Never release seat from base with child in seat.
• Use only with a child who is able to get in and out of the seat unassisted. Do not use
restraint system.
• Never use as a carrier or lift while child is seated.
• Never attach toddler seat to a chair.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information
• IMPORTANT! Please keep these instructions for future reference.
FCC Statement (United States Only)
• Please read these instructions before assembly and use of
this product.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Adult assembly is required. Tool required for assembly: Phillips
screwdriver (not included).
• Requires four “C” (LR14) alkaline batteries for swing operation
(not included).
• Product features and decoration may vary from photos.
Care
• Before use, thoroughly wash all parts (the tray) that may contact
food. The tray is not microwave or dishwasher safe.
• The bases, swing frame, legs, seat, toy and tray can be wiped clean
using a mild cleaning solution and a damp cloth. Do not immerse
the swing frame. Do not use bleach. Do not use harsh or abrasive
cleaners. Rinse clean with water to remove residue.
• The pad can be machine washed in cold water on the gentle cycle.
Do not use bleach. Tumble dry on low heat.
To remove the pad:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manu-
facturer responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
• Remove the four elastic loops from the pegs on the underside and
back of the seat.
• Push the waist and crotch restraints down through the slots in
the pad.
• Lift to remove the pad from the seat.
• Refer to the Seat Pad Assembly section to replace the pad.
ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.L’utilisation de ce dispositif est autorisée seule-
ment aux conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad.
Toy
2 Infant Seat Side Rails
(Left and Right)
Infant Seat Rear Crossbar
Infant Seat Front Crossbar
High Chair Tray
2 Toddler Seat Side Rails
(Left and Right)
Toddler Seat Rear
Crossbar
Toddler Seat Front Crossbar
Swing Frame
2 Swing Arms
(Left and Right)
4 Legs
Pad
Seat
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
Note: The swing seat base is attached
to the seat to fit in the package. Please
remove the seat from the swing seat
base (see page 6).
#8 x 1" (2,5 cm) Screw – 20
Shown Actual Size
Swing Seat Base
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Seat
CAUTION
PRESS
This package contains small parts
in its unassembled state. For adult
assembly only.
Swing Seat
Base
PRESS
IMPORTANT! Before assembly and each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges. DO
NOT use if any parts are missing or broken. Contact Fisher-Price® for
replacement parts and instructions if needed. Never substitute parts.
T-strap
Slot
2
• If desired, fit the toy T-strap down through the slot in the seat.
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Seat Base
One-Time Assembly
Infant Seat
Side Rails
Infant Seat
Rear Crossbar
Infant Seat
Front Crossbar
Release Button
Release Button
3
1
• Fit the infant seat rear crossbar into the sockets in on the side rails,
as shown.
• Locate the infant seat side rails and the infant seat front crossbar.
• Position the infant seat side rails, as shown, with the release
buttons outward.
Hint: The crossbar is designed to fit the side rails one way. If it does
not seem to fit, turn it around and try again.
• Fit the crossbar into the sockets in the side rails, as shown.
Hint: The crossbar is designed to fit the side rails one way.
If it does not seem to fit, turn it around and try again.
2 Screws
2 Screws
4
• Insert two screws into the holes in the crossbar and tighten.
• Turn the infant seat base assembly upright.
2
• Insert two screws into the holes in the crossbar and tighten.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Swing Frame
One-Time Assembly
Swing Seat Base
Swing Frame Hubs
Swing Arms
1
BACK VIEW
3
• Slide the longer, straight ends of the swing arms through the
holes in the swing seat base.
• Fit the swing arms into the sockets in the swing frame hubs.
• Turn the assembly around.
Hint: The swing arms are designed to fit one way. If a swing arm
does not seem to fit, try inserting it into the other hole in the
swing seat base.
• Turn the assembly over.
2 Screws
2 Screws
2 Screws
2 Screws
FRONT VIEW
4
2
BOTTOM VIEW
• Insert two screws into each hub and tighten.
• Insert two screws into each swing arm and tighten.
• Turn the assembly upright.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Toddler Seat Base
One-Time Assembly
Curve
Toddler Seat
Rear Crossbar
Toddler Seat
Front Crossbar
Toddler Seat
Side Rails
3
• Fit posts on the toddler seat rear crossbar into the sockets in
side rails.
Hint: The crossbar is designed to fit one way. If it does not seem to
fit onto the side rails, turn it around and try again.
Release Button
1
Release Button
• Position the toddler seat side rails, with the release buttons outward.
• Position the toddler seat front crossbar with the curve outward.
• Fit posts on the crossbar into the sockets in side rails.
Hint: The crossbar is designed to fit one way. If it does not seem to fit
in the side rails, turn it around and try again.
2 Screws
2 Screws
4 Screws
4
• Insert four screws into the crossbar. Fully tighten the screws.
• Turn the toddler seat base upright.
2
• Insert four screws into the crossbar and tighten.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Seat Pad Assembly
Pad
Tabs
BOTTOM VIEW
Elastic Loop
Elastic Loop
Hole
Seat
Hole
3
SIDE VIEW
1
• Insert both elastic loops on the pad through the holes in the
seat bottom.
• Fit the pocket on the top of the pad over the seat back.
• From the bottom of the seat, hook the elastic loops to the tabs
on the seat.
Slots
Tabs
BOTTOM FRONT VIEW
Waist Belt
Waist Belt
Crotch Belt
Elastic Loops
4
2
FRONT VIEW
TOP VIEW
• Hook the elastic loops on the front edge of the pad to the tabs
on the seat bottom.
• Lift the front edge of the pad up and fit the waist and crotch belts
up through the slots in the pad.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Swing Frame Battery Installation
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
1,5V x 4
“C” (LR14)
• Locate the battery compartment door on the swing frame.
• Loosen the screws in the battery compartment door with a
Phillips screwdriver.
• Insert four “C” (LR14) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws. Do
not over-tighten.
• If this product begins to operate erratically, you may need to reset
the electronics. Turn the power off and then back on.
• When motion from the swing becomes slow/faint or stops, it's
time to replace the batteries.
• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Use one seat 4 different ways!
Infant Swing
Infant Seat
High Chair
Toddler Seat
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Seat Use
Seat
WARNING
To prevent serious injury or death:
• Fall Hazard
- Never use on any elevated surface,
since child's movement may cause
infant seat to slide or tip over. Use
only on a floor.
Infant Seat Base
- Never release seat from base with
child in seat.
• Suffocation Hazard - Never use on a
soft surface (bed, sofa, cushion), since
infant seat may tip over and cause
suffocation in soft surfaces.
• Always use restraint system.
• Never leave child unattended.
• The infant seat is not intended to
replace a crib or bassinet for prolonged
periods of sleep.
Hint: If you are converting to an infant seat from high chair, toddler
seat or swing modes, remove the seat from the toddler seat base
or swing seat base.
• Fit the seat onto the infant seat base.
• Push to “snap” the seat onto the base. Pull up on the seat to
be sure it is secure.
• Never use infant seat for a child able
to sit up unassisted.
• Never attach infant seat to a chair.
• Never use as a carrier or lift while child
is seated.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Swing Use
WARNING
PRESS
To prevent injury or death from
falls and being strangled in the
restraint system:
PRESS
• Always use restraint system.
• Never use with an active child who
may be able to climb out of swing.
• Never leave child unattended.
• Never release seat from frame with
child in swing. Never carry child in seat.
1
Hint: If you are converting to an infant swing from infant seat mode,
follow this step.
• Press the release buttons on each side of the seat.
• Lift the seat off the infant seat base.
• Set the infant seat base aside for future use.
Swing Frame
Legs
Legs
2
Hint: If you are converting to an infant swing from high chair mode,
remove the legs from the toddler seat base.
• Fit the legs into the holes in the bottom of the swing frame,
as shown.
• Push to “snap” each leg in place. Pull on each leg to be sure it
is secure.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Swing Use
Speed/Power
Switch
Seat
Swing Seat Base
4
3
• Slide the swing speed/power switch ON
• Give the seat a light push to start the swinging motion.
• Adjust the swing speed/power switch to the desired swing
motion setting.
.
•
Hint: If you are converting to an infant swing from high chair or
toddler seat modes, remove the seat from the toddler seat base.
• Fit the seat onto the swing seat base.
• Push to “snap” the seat in place. Pull up on the seat to be sure
it is secure.
Hints:
- After turning on power, this product may not swing unless there is
a child in the seat.
- As with most battery-power swings, a heavier child will reduce
the amount of swinging motion on all settings. In most cases, the
low setting works best for a smaller child while the higher setting
works best for a heavier child.
- If swinging stops while using a lower setting, try a higher setting.
Give the seat a light push to start the swinging motion again.
• Slide the swing speed/power switch OFF when you are finished.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
High Chair Use
WARNING
To prevent serious injury or death
from falls or sliding out:
PRESS
PRESS
PRESS
PRESS
• Always secure child with restraint
belts adjusted to fit your child snugly.
The tray is not designed to hold child
in high chair.
• Use only with a child who has enough
upper body control to sit unassisted.
• Never leave child unattended.
• Never release seat from base with
child in high chair. Never carry child
in seat.
2
• Press the release buttons on the swing frame assembly and pull to
remove the legs.
PRESS
PRESS
Toddler Seat Base
1
Hint: If you are converting to a high chair from swing mode, follow
steps 1 and 2.
• Press the release buttons on each side of the seat.
• Lift the seat off the swing seat base.
Legs
Legs
3
• Insert each of the legs into the holes in the toddler seat base.
• Push to “snap” each leg in place. Pull on each leg to be sure it
is secure.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
High Chair Use
Seat
High Chair Base
6
• While pulling the release handles on the sides of the tray, adjust
the tray forward or backward.
4
Hint: If you are converting to a high chair from infant seat mode,
remove the seat from the infant seat base.
• Fit the seat onto the high chair base.
• Push to “snap” the seat in place. Pull up on the seat to be sure
it is secure.
Tray
7
• While pulling the release handles on the sides of the tray, pull the
tray towards you and lift to remove it from the seat.
5
Using the Tray
• Fit the tray onto the seat armrests. Push down until the tray
"snaps" into place.
Hint: Before use, thoroughly wash all parts (the tray) that may
contact food. The tray is not dishwasher or microwave safe.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Toddler Seat Use
WARNING
To prevent serious injury or death:
• Fall Hazard
PRESS
PRESS
PRESS
PRESS
- Never use on any elevated surface,
since child’s movement may cause
the product to slide or tip over. Use
only on a floor.
- Never release seat from base with
child in seat.
• Use only with a child who is able to get
in and out of the seat unassisted. Do
not use restraint system.
• Never use as a carrier or lift while child
is seated.
2
• Press the release buttons near each leg and pull to remove each leg.
• Never attach toddler seat to a chair.
Seat
Toddler Seat Base
3
Hint: If you are converting to toddler seat from infant seat or swing
modes, remove the seat from the infant seat base or swing seat base.
• Fit the seat onto the toddler seat base.
• Push to “snap” the seat onto the base. Pull up on the seat to be
sure it is secure.
1
Hint: If you are converting to toddler seat from high chair mode,
follow steps 1 and 2.
• While pulling the release handles on the sides of the tray, pull the
tray towards you and lift to remove it from the seat.
4
Restraint System
• Store the restraint system underneath the pad.
• Unbuckle the restraint system.
18• Push the waist and crotch belts back through the slots in the pad.
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant Seat, Infant Swing and High Chair
Restraint System Use
Free End
Free End
Anchored End
Anchored End
Waist Belt
Waist Belt
TIGHTEN
LOOSEN
3
To tighten the waist belts:
• Feed the anchored end of the waist belt up through the buckle to
A
B
form a loop . Pull the free end of the waist belt
.
To loosen the waist belts:
• Feed the free end of the waist belt up through the buckle to form a
A
loop . Enlarge the loop by pulling on the end of the loop toward
Crotch Belt
1
the buckle. Pull the anchored end of the waist belt to shorten the
B
free end of the waist belt
.
Securing Your Infant
• Place your child in the seat. Position the crotch belt between
your child’s legs.
• Fasten the waist belts to the crotch belt. Make sure you hear a
“click” on both sides.
• Tighten each waist belt so that the restraint system is snug
against your child. Please refer to step 3 for instructions to
tighten the waist belts.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Adjuster
Adjuster
4
SHORTEN
LENGTHEN
To shorten the crotch belt:
• Hold the adjuster and pull the rear crotch strap down.
To lengthen the crotch belt:
• Slide the adjuster up.
Waist Belt
Waist Belt
2
• Adjust the length of the crotch belt so that the waist belts rest on
baby's belly button.
• Please refer to step 4 in this section for instructions on how to
shorten or lengthen the crotch belt.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TNCE
AYUDA AL CONSUMIDOR
SERVICE À LA CLIENTÈLE
1-800-432-5437 (US & Canada)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers/Clientes con problemas auditivos/
Pour les malentendants: 1-800-382-7470.
En México: 59-05-51-00 Ext. 5205 ó 01-800-463-59-89
CANADA
VENEZUELA
Mattel Canada Inc., 6155 Freemont Blvd.,
Mattel de Venezuela, C.A., RIF J301596439, Ave. Mara, C.C. Macaracuay Plaza,
Torre B, Piso 8, Colinas de la California, Caracas 1071.
ARGENTINA
MÉXICO
Mattel Argentina, S.A., Curupaytí 1186, (1607) – Villa Adelina, Buenos Aires.
Importado y distribuido por Mattel de México, S.A. de C.V.,
Insurgentes Sur #3579, Torre 3, Oficina 601, Col. Tlalpan,
Delegación Tlalpan, C.P. 14020, México, D.F. R.F.C. MME-920701-NB3.
COLOMBIA
Mattel Colombia, S.A., calle 123#7-07 P.5, Bogotá.
CHILI
Mattel Chile, S.A., Avenida Américo Vespucio 501-B, Quilicura, Santiago, Chile.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2010 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
Fisher-Price, Inc., une filiale de Mattel, Inc., East Aurora, New York 14052, É.-U.
©2010 Mattel, Inc. Tous droits réservés.
® et ™ désignent des marques de Mattel, Inc. aux É.-U.
PRINTED IN CHINA/IMPRIMÉ EN CHINE
T3643pr-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
|