LBPS310A-KIT
LBPS311A
LBPS312A
Hardened PoL PoE Ethernet Extenders
Hardened PoL PoE Ethernet Extenders
Extends Power over Ethernet up to 1.2 km over ordinary
voice-grade copper wire.
Features Ethernet extension up to 2.2 km.
Customer Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
Support call 724-746-5500) • FREE technical support 24 hours a day,
Information
7 days a week: Call 724-746-5500 or fax 724-746-0746
• Mailing address: Black Box Corporation, 1000 Park Drive,
•
E-mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
∞
∞
Connect one end of the one pair copper wire to the RJ-11 phone jack or 2-pin
Terminal Block interface of the Transmitter and connect the other end to RJ-11
phone jack or 2-pin Terminal Block interface of the Receiver.
Data can be transmitted between the Transmitter and the Receiver via copper wire.
Physical Description
The Port Status LEDs and Power Inputs
Transmitter
Receiver
∞
∞
DC Terminal Block Power Inputs: 2.5A @ 48VDC (Peak current 3.26A). Two pairs of
power inputs can be used to power up this Ethernet Extender. The redundant power
supplies function is supported. You only need to have one power input connected to
run the Ethernet Extender.
DC JACK Power input: 2.5A @ 48VDC (Peak current 3.26A).
User’s Manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Power Input Assignment
Power1
48VDC
DC Jack
ꢀ
ꢁ
ꢀ
ꢁ
T:46-57V / R:46-57V DC
Power Ground
Power2
Terminal
Block
T:46-57V / R:46-57V DC
Power Ground
Power3
Earth Ground
DIP Switch Down
Transmitter
Up
PoL
Disable Power over Link
Std (Standard)
Standard line speed
Better noise immunity
Enable Power over Link
Per (Performance)
Better line speed
Type
Poor noise immunity
Receiver
Mode
Loc (Local)
Set Receiver to Local Mode
Std (Standard)
Standard line speed
Better noise immunity
Rmt (Remote)
Set Receiver to Remote Mode
Per (Performance)
Better line speed
Type
Poor noise immunity
LEDs
Power
1/2/3
State
Steady
Off
Indication
Power received
Power off
Steady
Power Ethernet extension interface function is enabled
No power is transmitted over Ethernet extension
interface
PoL
PoE
Off
Steady
Off
Steady
Powered device (PD) is connected
Powered device (PD) is disconnected
A valid Extender connection is established
Fast
Flashing
Slow
Flashing
Off
Data is being transmitted or received
Link
Extender port under negotiation mode
Extender interface connection is not established
Displays the link speed in Mbps
Line
Steady
Speed
PSE
Output
Steady
All off
PoE power can be transmitted for PD
No PoE power can be transmitted for PD
Steady
Flashing
Off
Steady
Off
A valid Ethernet connection established
Data transmitted or received
Non-Ethernet connection is established
Link speed at 100Mbps
Green
Yellow
Link speed at 10Mbps
User’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Power over Link (PoL) Enabled
Distance Data Rate Receiver PoE Output
300M
400M
600M
800M
1000M
1200M
100Mbps 30.0W
90Mbps
60Mbps
45Mbps
35Mbps
20Mbps
15.4W
14.0W
9.5W
7.0W
5.0W
Power over Link (PoL) Disabled
Power Supply Applied on Receiver
Distance
1400M
1600M
1800M
Data Rate Receiver PoE Output
15Mbps
10Mbps
3Mbps
30.0W
30.0W
30.0W
30.0W
Up to 2200M 1Mbps
<Note> The Reference Performance is tested on 24AWG Telephone wire (0.5mm
diameter, 1-pair wire, Cable impedance: 100ohm).
10/100Base-TX and Ethernet Extender Connectors
10/100Base-TX Connection
The following table lists the pinouts
of the 10/100Base-TX RJ-45 port.
Pin Regular Port
PoE Port
Output Transmit Data + Output Transmit Data +
Output Transmit Data - Output Transmit Data -
1
2
3
4
5
6
7
8
Input Receive Data +
Input Receive Data +
Positive (VCC+)
Positive (VCC+)
Input Receive Data -
Input Receive Data -
Negative (VCC-)
Negative (VCC-)
User’s Manual
4
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Ethernet Extender Connection
The RJ-11 and Terminal Block port pinouts:
Pin 3: Tip, Pin 4: Ring.
Use a telephone line to connect two
RJ-11 or Terminal Block ports between
two Hardened Ethernet Extenders.
Functional Description
∞
∞
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, full/half-duplex; Auto MDI/MDIX.
∞
∞
Auto data rate negotiation for the Ethernet extension interface.
Supports six speeds with speed indicator LEDs on the front panel of the
unit, up to 100Mbps @ about 300 meters (984 ft.), down to 1Mbps @
about 2,200 meters (7,218 ft.).
∞
∞
Supports Power over Ethernet applications up to 1,200meters (3,937ft.)
for Max. 5 watts power consumed PoE powered devices.
Power consumption:
-
-
Enable Power over Link (PoL) function: Max. 65 Watts
Disable Power over Link (PoL) function: Transmitter: Max. 5 W.
Receiver: Max. 35 W with PoE output, Max. 5 W without PoE
output.
∞
∞
Power Supply: Redundant T:46-57V / R:46-57V DC Terminal Block
power inputs and 48 VDC Latched DC JACK interface.
Operating temperature range @ -40 to 75 (-40ꢀ to 167ꢀ). Tested
for functional operation @ -40 to 85 (-40ꢀ to 185ꢀ).
∞
Supports Din-Rail or Panel Mounting installation.
User’s Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Preface
This manual describes how to install and use the Hardened Ethernet
Extender. The Hardened Ethernet Extender introduced here provides one
channel for Ethernet over existing voice grade copper wire.
The Hardened Ethernet Extender fully complies with IEEE802.3 10Base-T
and IEEE802.3u 100Base-TX standards.
In this manual, you will find:
∞
∞
∞
∞
∞
Product overview
Features on the Hardened Ethernet Extender
Illustrative LED functions
Installation instructions
Specifications
User’s Manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Table of Contents
Quick Start Guide............................................................................. 1
Installation........................................................................................ 1
Physical Description........................................................................ 2
The Port Status LEDs and Power Inputs ..................................... 2
10/100Base-TX and Ethernet Extender Connectors................... 4
Functional Description.................................................................... 5
Preface ................................................................................................ 6
Table of Contents .............................................................................. 7
Introduction ....................................................................................... 8
Product Overview ............................................................................ 8
Product Features ............................................................................. 8
Packing List...................................................................................... 9
One-Channel Hardened Ethernet Extender............................... 10
Ports................................................................................................ 10
Ethernet Extender Mode Settings.................................................. 10
DIP Switch...................................................................................... 10
Front Panel & LEDs...................................................................... 11
LED Indicators ............................................................................ 11
10/100Base-TX and Ethernet Extender Connectors................. 12
Installation ....................................................................................... 13
Selecting a Site for the Equipment................................................ 13
DIN Rail Mounting ........................................................................ 13
Connecting to Power ..................................................................... 15
Redundant DC Terminal Block Power Inputs........................... 15
48VDC DC Jack.......................................................................... 15
Specifications ................................................................................... 17
User’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Introduction
The Hardened Ethernet Extender provides one channel for Ethernet over
existing voice grade copper wire. This Hardened Ethernet Extender solution
works in industrial applications or rugged environments.
Product Overview
Transmitter
Receiver
Product Features
∞
∞
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, full/half-duplex; Auto MDI/MDIX.
∞
∞
Auto data rate negotiation for Ethernet extension interface.
Support six speeds with speed indicator LEDs on front panel of unit, up
to 100Mbps @ about 300 meters (984 ft.), down to 1Mbps @ about
2,200 meters (7,218 ft.).
User’s Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
∞
∞
Supports Power over Ethernet applications up to 1,200 meters (3,937ft.)
for Max. 5 watts of power consumed by PoE powered devices.
Power consumption:
-
-
Enable Power over Link (PoL) function: Max. 65Watts
Disable Power over Link (PoL) function: Transmitter: Max. 5W.
Receiver: Max. 35W with PoE output, Max. 5W without PoE output.
∞
∞
Power Supply: Redundant T:46-57V / R:46-57V DC Terminal Block
power inputs and 48 VDC Latched DC JACK interface.
Operating temperature range @ -40 to 75 (-40ꢀ to 167ꢀ). Tested
for functional operation @ -40 to 85 (-40ꢀ to 185ꢀ).
∞
Supports Din-Rail or Panel Mounting installation.
Packing List
Your package should contain the following items. IIf anything is missing or
damaged, contact Black Box Technical Support at 724-746-5500 or
∞
∞
∞
The Hardened Ethernet Extender
User’s Manual
AC to DC Power Adapter and Power Cable (optional)
User’s Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
One-Channel Hardened Ethernet Extender
Ports
The Hardened Ethernet Extender provides TX ports and one Ethernet
Extender port.
For the TX ports, it uses RJ-45 connectors and auto senses the speed of
10/100 Mbps.
For the Ethernet Extender port, it uses RJ-11 and Terminal Block
connectors
and
auto
senses
the
speed
of
Link
(below
20)/20/40/60/80/100Mbps.
Ethernet Extender Mode Settings
Ethernet Extender mode settings are simple using a DIP (Dual Inline
Package) switch on the top panel of the Hardened Ethernet Extender.
ꢀ
DIP Switch
DIP
Down
Up
Switch
Transmitter
PoL Disable Power over Link
Std (Standard)
Type Standard line speed
Better noise immunity
Receiver
Enable Power over Link
Per (Performance)
Better line speed
Poor noise immunity
Loc (Local)
Set Receiver to Local Mode
Std (Standard)
Standard line speed
Better noise immunity
Rmt (Remote)
Mode
Set Receiver to Remote Mode
Per (Performance)
Better line speed
Type
Poor noise immunity
ꢀ
User’s Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Front Panel & LEDs
LED Indicators
The LED indicators give you instant feedback on the status of the Hardened
Ethernet Extender:
LEDs
Power
1/2/3
State
Steady
Off
Indication
Power received
Power off
Power Ethernet extension interface function is
enabled
No power is transmitted over Ethernet
extension interface
Powered device (PD) is connected
Powered device (PD) is disconnected
A valid Extender connection established
Steady
Off
PoL
PoE
Steady
Off
Steady
Fast
Flashing
Slow
Flashing
Off
Data transmitted or received
Link
Extender port under negotiation mode
Extender interface connection is not established
Displays the link speed in Mbps
Line
Speed
Steady
PSE
Output
Steady
All off
PoE power can be transmitted for PD
No PoE power can be transmitted for PD
A
valid Ethernet connection
Steady
Flashing
Off
established
Data transmitted or received
Non-Ethernet
established
Green
Yellow
connection
is
Steady
Off
Link speed at 100Mbps
Link speed at 10Mbps
Power over Link (PoL) Enabled
Distance Data Rate Receiver PoE Output
300M
400M
600M
800M
1000M
1200M
100Mbps 30.0W
90Mbps
60Mbps
45Mbps
35Mbps
20Mbps
15.4W
14.0W
9.5W
7.0W
5.0W
User’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Power over Link (PoL) Disabled
Power Supply Applied on Receiver
Distance
1400M
1600M
1800M
Data Rate Receiver PoE Output
15Mbps
10Mbps
3Mbps
30.0W
30.0W
30.0W
30.0W
Up to 2200M 1Mbps
<Note> The Reference Performance is tested on 24 AWG Telephone wire (0.5 mm
diameter, 1-pair wire, Cable impedance: 100 ohm).
10/100Base-TX and Ethernet Extender Connectors
10/100Base-TX Connection:
The following table lists the pinouts
of a 10/100Base-TX RJ-45 port.
Pin Regular Port
PoE Port
Output Transmit Data + Output Transmit Data +
Output Transmit Data - Output Transmit Data -
1
2
3
4
5
6
7
8
Input Receive Data +
Input Receive Data -
Input Receive Data +
Positive (VCC+)
Positive (VCC+)
Input Receive Data -
Negative (VCC-)
Negative (VCC-)
Ethernet Extender Connection
The RJ-11 and Terminal Block port pinouts:
Pin 3: Tip, Pin 4: Ring.
Use a telephone line to connect two
RJ-11 or Terminal Block ports between
two Hardened Ethernet Extenders.
User’s Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Installation
This chapter gives step-by-step installation instructions for the Hardened
Ethernet Extender.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will not
be subjected to extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should meet the following
requirements:
∞
The Surrounding Air temperature should be between -40 to +167 degrees Fahrenheit
(-40 to +75 degrees Celsius).
∞
∞
The relative humidity should be less than 95 percent, non-condensing.
Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.
∞
∞
Make sure that the equipment receives adequate ventilation. Do not block the
ventilation holes of the equipment.
The power outlet should be within 6 feet (1.8 meters) of the product.
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the Hardened Ethernet
Extender.
Installation: Place the Hardened Ethernet Extender on the DIN rail from
above using the slot. Push the front of the Hardened Ethernet Extender
toward the mounting surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the Hardened Ethernet
Extender from the DIN rail.
User’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
User’s Manual
14
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Connecting to Power
Redundant DC Terminal Block Power Inputs or 48-VDC DC Jack:
Redundant DC Terminal Block Power Inputs
Two pairs of power inputs can be used to power up this device. You only
need to have one power input connected to run the Hardened Ethernet
Extender.
Step 1: Connect the DC power cord to the pluggable terminal block on the Hardened
Ethernet Extender, and then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the Hardened Ethernet
Extender.
48VDC DC Jack
Step 1: Connect the supplied AC to DC power adapter to the receptacle on the top side of
the Hardened Ethernet Extender.
Step 2: Connect the power cord to the AC to DC power adapter and attach the plug to a
standard AC outlet with the appropriate AC voltage.
User’s Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Power Input Assignment
Power1
48VDC
DC Jack
ꢀ
ꢁ
ꢀ
ꢁ
T:46-57V / R:46-57V DC
Power Ground
T:46-57V / R:46-57V DC
Power Ground
Power2
Terminal
Block
Power3
Earth Ground
User’s Manual
16
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Specifications
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX
10/100Mbps Ethernet ports with RJ-45 connectors
Applicable Standards
Fixed Ports
1 x Ethernet Extender port with RJ-11 and Terminal
Block connectors
Speed
10Base-T
10/20Mbps for half/full-duplex
100Base-TX
Ethernet Extender
100/200Mbps for half/full-duplex
Link (Below 20), 20, 40, 60, 80, 100Mbps
Switching Method
Forwarding rate
Cable
Store-and-Forward
14,880/148,810pps for 10/100Mbps
10Base-T
100Base-TX
Ethernet Extender
4-pair UTP/STP Cat. 3, 4, 5 up to 100m
4-pair UTP/STP Cat. 5 up to 100m
Telephone wires
LED Indicators
Per Unit (3 LEDs)- Power1, Power2, Power3
Transmitter-
PoL; Line Speed (Mbps): Link, 20, 40, 60, 80, 100
Receiver-
PoE; Line Speed (Mbps): Link, 20, 40, 60, 80, 100; PSE
Output (Watts): 5, 15, 30
Dimensions
Weight
50mm (W) ꢀ 110mm (D) x 135mm (H)
(1.97” (W) x 4.33” (D) x 5.31” (H))
0.77Kg (1.7lbs.)
Terminal Block: T:46-57V / R:46-57V DC
DC Jack: 48VDC, External AC/DC required
Terminal Block & DC Jack Power Inputs: 2.5A @
48VDC (Peak current 3.26A)
Power
Power Consumption
Enable PoL: Max. 65Watts
Disable PoL:
Transmitter: Max. 5W
Receiver: Max. 35W with PoE output
Max. 5W without PoE output
User’s Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Base-TX Hardened PoL/PoE Ethernet Extender
Operating Temperature
-40ꢀ ~ 75ꢀ (-40ꢁ ~ 167ꢁ)
Tested for functional operation @
-40ꢀ ~ 85ꢀ (-40ꢁ ~ 185ꢁ)
Storage Temperature
-40ꢀ ~ 85ꢀ (-40ꢁ ~ 185ꢁ)
5 ~ 95%, non-condensing
FCC Part 15, Class A
Humidity
EMI
EN61000-6-4: EN55022, EN61000-3-2, EN61000-3-3
EN61000-6-2:
EN61000-4-2 (ESD Standard)
EMS
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
Environmental Test
Compliance
IEC60068-2-32 Ed (Free Fall)
User’s Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 30 seconds away at 724-746-5500
or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure products.
You’ll find everything from cabinets and racks and power and surge protection
products to media converters and Ethernet switches all supported by free, live
24/7 Tech support available in 30 seconds or less.
© Copyright 2013. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond
logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in
this white paper are acknowledged to be the property of their respective owners.
LBPS310A-KIT, version 1
Download from Www.Somanuals.com. All Manuals Search And Download.
|