SVSound
OWNERS’
GUIDE
SVS PB12-Plus Powered Box,
Single “Plus” Driver
Subwoofer
Contents:
•
•
•
•
•
•
•
•
•
•
Pages 2-3 Safety instructions
Page 4 SVS Welcome
Page 5 About your new SVS Subwoofer
Pages 6-8 Setup, integration, and calibration
Pages 9-10 Powered box amp features
Pages 11-13 Parametric equalizer (PEQ)
Pages 14 - 15 Variable tuning
Pages 16 - 17 Bass demos
Pages 18-19 Dealers/Notes
Page 20 Terms and Conditions
Last update: 14 May 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
SV Sound
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, this apparatus
should not be exposed to rain or moisture and objects filled with liq-
uids, such as vases, should not be placed on this apparatus.
16. To completely disconnect this equipment from the mains, disconnect
the power supply cord plug from the receptacle.
17. The mains plug of the power supply cord shall remain readily operable.
The lightning flash with arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of un-insulated "dangerous voltage " within
the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
SV Sound
Welcome.
From the entire SVS team, congratulations on your purchase of a
new standard in home theater and music bass!
Your sub isn’t some generic black box built someplace you can’t even
find on a map. It’s made in our Ohio, USA factory by home audio
fanatics... like you. Designed, and tested using the latest state of the
art instruments... and assembled by hand, your SVS subwoofer is
without a doubt one of the best investments you’ll ever make in bring-
ing music and theater home.
We’ll help you to set up your sub right, and in no time, you’ll be giv-
ing “demos” of your favorite DVDs or music selections to all your
friends and neighbors (be kind if you live in an apartment). This isn’t
just a “subwoofer” after all, it’s a carefully designed audio component
carefully tuned in our labs, by the award-winning SVS design team.
You’re unlikely to have heard, or felt, bass like this before, unless it
was in a top-notch, commercial movie theater. Audio in your home
will never be quite the same again. That’s a promise.
Already have a question about your sub? You might answer it by
reading this manual, we think you’ll find it easy to read and more
informative than most. For even more detailed discussion about set-
We touch on all the key points you need to know, and then some.
Maybe you just want to share a bit of bass news? Or perhaps you
have a story about your SV Subwoofer to share with us? Maybe
something we missed in our website? No matter, feel free to send a
tail website in your region.
It’s not often you can talk to the guys who made your audio compo-
nent. In this case, we look forward to it.
SVS Customer Service
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
SV Sound
About your SVS Subwoofer
There maybe be other subwoofers that look like them, but virtually none
work like them. Not at this price. SVS subwoofers are decidedly different in how they
are designed, produced, sold, and even in the exceptionally high quality components
we use. The best part? You could have spent much more and still not come close to
the performance our subwoofers provide. So, what makes a subwoofer an SVS?
Quality components, sane prices. You might be surprised at how inexpensive
the components are in some not-so-inexpensive subwoofers. At SVS, performance is
king... not shaving off a few dollars from component costs to improve profits. We
scour the earth for the most cost-effective parts (when we don’t make them ourselves),
and meld them into finely tuned designs that define high performance movie and
music bass. We’ve tested and discarded plenty of bits that didn’t meet our tough
standards. If we use it, you know “it” is satisfied some tough customers first. Us.
Get “square”. We did a host of studies to optimize materials, the size, and even the
our enclosure finishes to ensure a rigid design that’s reasonably compact, and still able
to take the abuse your family and friends can dish out. SVS cabinets are no ordinary
boxes. Selling through select dealers means your sub, and not glossy ads, get the
priority at when your product is built. Tap the side of your sub, look at those smooth
corners, flip a few switches. The quality is so obvious, you’ll know what we mean.
SVS products are different.
Stable downward firing woofer. Our contemporary enclosure designs are a halmark,
but we’ve also taken great lengths to allow for top quality, well-protected woofers.
Coupled with our unique base-plates, which minimize driver reactive forces, you’ll
find our down firing subs can take a tremendous amount of power and remain rock
solid. Compliant rubber feet allow for stable placement on a variety of surfaces. No
rattling, or buzzing allowed!
Custom low turbulence port designs. When you listen to our trend-setting
ported subs you’ll hear (and feel) bass like never before, with a exceptionally low
noise and distortion. Huge patented, flared port fittings make the difference. You’ll
quickly realize something special went into your new sub the second you fire it up.
Stylish, and understated. From the fine, durable finish, to the attractive color-
contrasting components, you’ll be amazed at how easy it is to lose your sub in a
corner. SVS’s aren’t tiny, but this is one of those times size does matter. There are
many brands of boring “black box” subs. Fortunately, you didn’t just unpack one.
World class power. Our Canadian-built amps are designed and manufactured with
a level of quality and power practically unheard of at this price. Did we mention
power? It’s there in spades (though we rate them conservatively). And SVS starts
with efficient designs which don’t require significant levels of power robbing
equalization to go low and flat. This way, our amps can be dedicated to reproducing
low frequencies, not making up for a lack of enclosure space (the bane of clean, deep
bass). As a result, we don’t require the megawatts some subs do.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
SVSound
Setup, calibrating and integration
What’s to know? Well, first of all, setting up an SVS subwoofer is
pretty darn easy. There are a few key things to get right though if you
want to get the most out of your sub.
Unpacking. You’re probably eager to hear your sub, but take time to
carefully unpack everything. Save the box and shipping materials, just
in case you need to return the sub for any reason.
Location. They say it’s “all about location” right? It’s the same with
subwoofers. So, where to put it? Go for a corner if you can, and avoid
putting your sub where it might adjoin large open areas
.
Studies have
shown that the deepest and flattest bass response is typically attained
when a subwoofer is placed within a few feet of one of your room’s
corners (leave about 3” in the back for port and cable clearance with any
wall or other surface). A corner near your favorite seat is often the best
of all locations. Whether you put the sub in front or to the rear of your
seating area makes surprisingly little difference. Deep home theater
bass, like that from “5.1 channel” DVDs is non-directional. You can’t
tell where it is coming from, even though you can hear, and feel it.
Hook-up (see Fig. 1). There are a variety of ways to configure your
new sub. Usually, a simple mono, shielded 75 Ohm A/V RCA type
cable (a.) is used to take the subwoofer output of your DD/DTS
surround sound receiver (b.) and feed the low-level input of the sub’s
amp. There is no need to “split” the signal going to the sub (c.). You
can feed either one of the two amp inputs, it doesn’t matter, right or left.
NOTE: Stop now if you aren’t
TOTALLY familiar with your re-
ceiver’s manual. Ensure all power
to your equipment is off when
making these connections. Also, be certain
your power outlet can handle a minimum of
600 watts. (Use of “convenience outlets” on
receivers are not recommended for your SVS).
(a.)
(c.)
(b.
DD/DTS Processor/Receiver
(Subwoofer “Out”)
Fig. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SVSound
Page 7
More Setup, calibrating and integration
If you are running a pair of SVS subwoofers (Fig. 2), you will need to
use a standard “Y” cable adapter (d.) The best adaptor to use for this task
has one male RCA connection and two female RCA outputs. From the
“Y” cable you can run a standard 75 Ohm RCA to RCA signal cable (e.)
to each sub, thus “splitting” the Low Frequency Effects (LFE) and other
bass signals from your receiver and effectively feeding both subwoofers
with the same signal. Contact us for hints on optimizing twin subs.
NOTE: Now is a good time to select
if you want “ON” (always on) or
“AUTO ON” which turns your sub
on only when a bass signal is present.
“Y” cable/splitter from
receiver
(e.
(d.)
DD/DTS Processor/Receiver
(Subwoofer “Out”)
Fig. 2
“
Level Calibration” isn’t only for tech minded folks, it’s critical to a
proper configuration of your home theater sound system. Fortunately,
adjusting channel output balance (essentially all “calibration” amounts to)
is as simple to do as it is important. The first order of business is making
sure your DD/DTS surround sound system is set up properly. We recom-
mend you consult your audio/video receiver (or processor) manual to re-
fresh on the procedures to do this. Generally, this requires ensuring the
receiver’s test tones, or a special test disk (like Ovation Software’s Avia
)
play back at the same volume from each of your system’s speakers.
That’s speakers at left, center, right, left surround and right surround (and
if equipped, one or two rear channels), plus the subwoofer . (More on sub
level in a second). Skip to page 9 (“Powered Box Features”) if you aren’t
familiar with your sub’s amp, and come back to calibration.
Some things to check as you get ready to calibrate:
•
Are your speakers set correct to the correct “size”? Your re-
ceiver/processor should allow you to indicate if your speakers are
“Small” or “Large”. Selecting the size accordingly will ensure bass
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 8
goes to most appropriate speakers, and use the subwoofer correctly too.
“Small” is nearly always the best setting for today’s speakers. Also, is
your subwoofer turned “ON”? We don’t mean “is your subwoofer ampli-
fier on?” (that’ll be important later too) but rather, is your receiver send-
ing a bass signal to your sub amp? This can only happen if you say
“Yes” (or “ON”) in the “Subwoofer” selection during the setup of any
typical Dolby Digital/DTS capable receiver (you’ll need to enter your re-
ceiver’s setup “menu” to check these critical choices).
•
•
Is your receiver connected to the sub amp? Use a well-shielded RCA
cable (sometimes called a “patch cord”) to connect the subwoofer output of your
DD/DTS receiver to either input jack of your SVS’s dedicated amp. Again, you’ll
need to “split” the bass signal with a “Y Cable” if you have a pair of subs. You
only need feed one of the two inputs (either Right or Left) of any
Powered Box SVS sub, these inputs are “summed” internally.
Is your Radio Shack
®
sound pressure level (SPL) me-
ter ready? This tool is absolutely essential to proper home
theater audio setup. It’s akin to a tire pressure gauge for your car
(you don’t set your tires by “feel” right?). Set the meter to “Slow”
and “C-weighting” (and turn the dial to 70 or 80dB depending on
your test tone source). Haven’t got the meter yet? Order one
from your dealer, or SVS. We prefer the analog instead of the
digital display model.
Getting ready to start now: Make sure your receiver/processor master volume is set
at “00 dB” or some other easy to remember “reference level”. Finally, ensure your
SVS’s volume/gain control is set no more than 1/4 to 1/3rd up, for now. It’s also criti-
cal to check the subwoofer level control of your surround receiver before you begin the
test tones. Set the receiver’s subwoofer output signal no higher than “-6 dB” initially
(that’s one quarter way up, given a typical receiver’s channel level limits of –12 dB to
+12 dB) . Your LFE “trim” or “peak limiter”, if you have one, should be set to 0dB
(with the least effect). This can be changed later if needed. Turn off any sound-field
processing schemes, “mid-night mode”, “DRC” (dynamic range control) etc. If it is an
option in your system, route your LFE to the “Subwoofer only”, not “Mains + Sub”.
Now play your receiver's internal test tones so you have something to measure
with your SPL meter. Or, better yet, buy a test DVD such as the Avia. A test disk’s
tones ensure your entire signal path, from the DVD player to your speakers, is set cor-
rectly. Whatever you use, when the tones start alternating from speaker to speaker
(watch your sound meter now), set each speaker’s volume to about 75 dB (or 85dB if
using Avia) by using the receiver’s dedicated channel level controls (leaving receiver’s
master volume the same). We recommend you turn down the receiver’s subwoofer
output level before you significantly lower your sub’s volume/gain control. This helps
keep distortion sent to your SVS at a minimum. You should not be set this control
much lower than –6 dB however, since some downward adjustment maybe be needed
to fine tune levels later. If your subwoofer reading is still too high, then turn down the
sub’s amp volume a little with each run.
Download from Www.Somanuals.com. All Manuals Search And Download.
But what’s “too high”?? Tastes vary, and so do movie soundtracks, but your SVS
is capable of tremendous levels of low distortion, low frequency bass — far more than
most consumer-quality subwoofers. Take advantage of this, especially if you like action
movies or music with lots of “.1” channel (LFE) bass action, and give the sub a bit more
“bump” during calibration. Keep in mind too that the human ear is relatively insensitive
to low frequencies. This, and the fact most folks don’t watch movies at Dolby Digital
reference level (“theater loud”), means upping the bass up a few dBs usually yields a
more satisfying movie and music experience at more restrained playback levels..
What sub levels do we recommend? If you watch movies at moderate sound lev-
els, a good start is a range of +1dB to +3dB above your other channels (as measured
with your sound meter). This means the test tone will waiver about 78 dB for the sub-
SV Sound
Page 10
ficult job of the phase control. Essentially, “phase” varies the timing of the bass
waves coming from the sub. But don’t despair if you don’t hear much difference,
especially if running a single subwoofer. Bass “cancellation” will vary by room
shape, volume, and the bass frequency. No one setting is likely to ever be perfect.
One technique to optimize phase is to find a nice “bassy” loop (such as the menu of
the “Godzilla” movie DVD) and measure the loop’s SPL response at various bass
peaks. As the loop runs, have an assistant adjust phase in small steps while you
measure. When you see the most response on a given bass passage, typically that’s
the setting with the least cancellation (for the frequencies of the demo loop).
Line In/Out. Use either of the sub’s “Line In” jacks to connect the subwoofer to the
output jack of your receiver/processor. Feeding just one input is enough. If you are
using a conventional amp and/or a stereo setup you can use the “Line Out” jacks to
send sound (filtered of deep bass information) back to your system amp. A simple
“:RCA to RCA” cable is all you need for either type configuration.
Auto On. Your SVS Powered Box allows itself to be in an “Auto-On” mode… or
“On” all the time. With the former setting (the switch in the “Auto” position) your
subwoofer will “sense” that a DVD or CD etc. has begun and switch its audio circuits
on immediately (the “hard” power switch mentioned below must be on, naturally). A
few minutes after a movie, the Auto-On light will turn Red, switching the sub back
off. When running (and sensing a signal) the Auto-On LED will be green. Some-
times, with very low listening levels, your subwoofer might not get enough of a bass
signal from your surround sound processor to “trip” the Auto-On circuit. Should you
ever find this to be the case, you may leave this switch to “On”, or turn up the re-
ceiver’s subwoofer output level some (be sure to recalibrate channels levels with your
meter afterwards).
Crossover enable switch. If you allow your DD/DTS surround-sound receiver or
processor to manage bass frequencies (again, highly recommended), this switch
should be set to “Disabled”, eliminating the effects of the “Crossover Frequency”
knob and allowing your sub to reproduce just what it’s fed from the receiver. If you
use the sub in a two channel (stereo only) configuration, then “Enable” the crossover
and adjust the knob to best blend the sub into the output of your speakers.
High level inputs/outputs. Not commonly used today, but binding posts are there in
case you don’t have low-level inputs/outputs on your receiver/processor. Typically
utilized only if you are not using a DD/DTS compatible system.
Power. This heavy-duty two-position switch next to the power cord will completely
cut the power to your sub amp. Flip this switch to off before you ever move the sub
or change inputs or outputs.
A/C connection. Plug your sub into a dedicated electrical outlet. “Convenience”
outlets of typical receivers often don’t provide the needed current. Do not use these.
Fuse. User replaceable, contact your dealer if you have trouble finding one. The
fuse can be accessed by a small door immediately next to the power cord fitting
(where you should also find a spare one for your use).
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 11
Parametric Equalizer (select PB12-Plus subs only). Important enough and
challenging enough, this feature gets its own section! “PEQ” allows you to tame a “peak”
in your room’s natural frequency response. Peaks are quite common, especially in large
rooms or ones where your sub is far from your listening position. NOTE: A Sound Pres-
sure Level meter is a must for proper use of the PEQ, so get one before you tackle this
control. TO DISABLE THIS CONTROL: Set the “LEVEL” control in the Parametric
EQ feature until it stops on “MIN” — thus ensuring you do not inadvertently cause poor
frequency response until such time as you properly configure the PEQ.
First you might ask yourself, “why use a PEQ?” The reason is quite simple. Your room.
Most times even a superlative subwoofer which measures very evenly (we say “flat”) in
an open domain (no reflective boundaries) will not measure the same in your home theater
or music room. Instead, colliding bass waves can build up and cause a “peak”. This is
where a parametric equalizer helps out. A PEQ is an electronic circuit which allows the
user to manipulate the input signal so the acoustical output is more desirable for their envi-
ronment, in many cases allowing the worst peak to be “flattened”. By manipulating the
input signal with your PEQ you can cut a wide or narrow peak in response located some-
where in the frequency range of the equalizer. Importantly, the equalizer found your sub
only allows reduction of peaks, and is “cut only”, not a boost device.
Measure the room’s response. As indicated above, you must have a firm understand-
ing of your room’s acoustical properties before you use a PEQ. To determine your room’s
natural response properties (and your subwoofer, in that room) you will need an SPL meter
shown on Page 6, and at least a pad of graph paper and a pencil for charting as below. If
you have graphing program similar to Microsoft Excel ® this will save some time chart-
ing the response curves. Contact SVS for tips on accessing advanced audio tools you can
use for room analysis. NOTE: Use extreme caution with sine-waves and only run very
low SPLs in the 75dB-85dB region. Sine waves at high SPL’s can damage your SVS!
Freq 20 25 30 35 40 45 50 55 60 65 70 75
80 85
90
95 100
86
SPL 85 84 86 91.5 95 90 84 84 86 86 85 83.5 83 83.5 84.5 85
Room A Response
96
93
90
87
84
81
20
40
60
80
100
Figure 3
Fr equency
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 12
When measuring the room’s response use a minimum resolution of 5Hz. Figure
3 on the previous page shows a theoretical illustration of a room’s response.
Before you plot your results however, it’s important to note the Radio Shack
sound meter is not totally "linear" in its accuracy down low. All similar meters
are off by the similar amount depending on the frequency; so while its sensitivity
below 20Hz is not what it is at 50Hz, there is a simple way to compensate for this
deficiency. It's called a compensation chart.
Simply look to the below frequencies and add the required decibels (dBs) at the
frequency in question. So if your system seems to be measuring 70dBs with a
20Hz tone, then really it's putting out 77.5dBs. This is a VERY substantial differ-
ence, roughly TWICE the acoustical energy, requiring several times the amplifier
power to achieve. You can see then how critical the below chart is if you are us-
ing your PEQ to even out or “flatten” the room response of your bass.
Add the following to your measurements:
10Hz add 20dBs
12Hz add 16.5db
16Hz add 11.5dB
20Hz add 7.5dB
25Hz add 5dB
31.5Hz add 3dB
40Hz add 2.5dB
50Hz add 1.5dB
63Hz add 1.5dB
80Hz add 1.5dB
100Hz add 2dB
125Hz add .5dB
Explanation of the controls. Now that we have dis-
SVS PEQ Controls
cussed how to measure the room’s response, the next
step is to correct the problem areas with the paramet-
ric equalizer. Before we start turning the controls we need to understand what the
adjustments are and how they work.
“Q”. This control determines how wide the correction will be. Each “hash mark”
on the amp’s front plate represents roughly 0.1 octave adjustments. The “HI”
mark is equal to 0.1 octave (narrow) and “LO” mark is equal to .9 octave (wide).
In Figure 3 the highest peak is located at 40Hz and becomes flat again at 50Hz
(the Highest Frequency of the peak). To determine the Q adjustment the follow-
ing formula is needed. More on “Q” in a moment.
Formula 1
(Highest Frequency [X] – Center Point [Y])
Center Point (Y)
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 13
The LEVEL control is the amount of attenuation on the signal located at the center
frequency. MIN is equal to 0dB and MAX is equal to -12dB “cut”. Each hash mark
reduces the Center Point in question by 1.5dB.
The “FREQ” control (short for frequency) is the adjustment for the center point of
the cut and should target the highest peak frequency in the room’s response. Each
hash mark for this control moves the center frequency for the desired cut 5Hz, within
a range of 20-80Hz.
Adjustments of the parametric equalizer. The first step to adjusting a PEQ is de-
termining the “Center Point” of the cut. Determining the Center Point allows us to
establish a target, or baseline, for further adjustments. In this example (again, looking
to the graph in Figure 3), the peak frequency is roughly 40Hz.
At this stage we’ll estimate the beginning (lowest frequency) and the end (highest
frequency) of the peak. In Figure 3 the beginning would be located somewhere near
25Hz and the end, or Highest Frequency, would be near 50Hz. This would be a
25Hz bandwidth, with a Center Point located at 37.5Hz (the midpoint between 25
and 50hz). Notice that the center point of 37.5Hz is not located precisely at the peak
frequency in the response curve, which was estimated at 40Hz. Why? If we used
40Hz as our center frequency and 50Hz as our high point cutoff we would only at-
tenuate the curve down to 30Hz. This will leave a small bump in response near 25Hz
because the correction would only be located between 30Hz to 50Hz.
Now that we determined the Center Point we can adjust the “FREQ” control knob to
37.5Hz, or between the fourth and fifth hash marks, clockwise from the left.
The next step will properly adjust the “Q” setting. We again need to use Formula 1
and calculate the Q setting from Figure 3 using Highest Frequency and Center Point
figures just determined above.
50Hz – 37.5Hz = 0.33
37.5Hz
.33 Q … or just past the third hash mark, clockwise from the left of this control.
Now that we have successfully adjusted the Q and Frequency controls, we need to
make the final Level adjustment. In Figure 3 the adjustment should be somewhere
near –10dB to –11dB, or on the 8th hash mark from the left (1.5dB cut per hash
mark), completing the adjustments for the parametric equalizer.
Measure room response for accuracy. After all the adjustments are made we rec-
ommend you measure the room again to make sure the adjustments are correct. If the
new response curve is not acceptable then fine-tune things some. For example, if the
response curve still shows a small peak you should adjust the Level control again to
compensate. Make sure your overall SPL calibration is set as described earlier in this
manual, and enjoy your optimized subwoofer!
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 14
Subsonic Filter and Port Tuning
Your new SVS subwoofer not only comes with our
efficient “Tri-Power” port flares, but custom port
plugs and variable subsonic filter which allow
your sub to be “tuned” to even lower frequencies
than its stock configuration. For most people and
most rooms, your SVS is already configured for
the best blend of extension (how deep/low your sub goes) and output (how loud it
gets at a variety of bass frequencies). However, we know that bass is a very personal
taste and no two rooms will react exactly the same with any subwoofer. So we in-
clude a custom “port plug” that, when inserted into a port, allows you the user to
experiment with a substantially lower “tune”.
As with all such devices, there are compromises when tuning a sub lower. Installing
a port block takes some capacity from upper reaches of bass, installing two port
blocks naturally limits upper bass response even more. So while you will indeed get
more bass down low (where DVD and music bass is more rare, but quite exciting),
you’ll sacrifice total output capacity above the stock tuning point of the sub (where
bass is more common). You should decide if the effect is pleasing on the sorts of
movies and music you enjoy.
How to do it? To insert a port plug, simply squeeze the foam on one end and press
the plug into a port flare until it is about 1” lower than the edge of the surface of the
sub. You can remove the plug by inserting your fingertips into the port flare and
squeezing and pulling on the foam plug at the same time. Be sure to select the sub-
sonic filter point on the back of your SVS amp which coincides correctly with your
new “tuning point”. NOTE: We strongly recommend you do NOT run a lower
subsonic filter point than your port plug configuration would dictate — especially if
you are running the subwoofer at high sound pressure levels. Moderate levels are
doubly important if you put the subsonic filter into the 12Hz mode (* contact SVS
about details on the use of this deepest mode). This simple table indicates the set-
tings you should use in setting up your sub blockers and the subsonic filter knob.
SVS PB12-Plus Tuning Chart
Stock tune (no ports blocked)
With one port-blocked
Subsonic Filter Knob
20Hz
16Hz
12Hz
With two ports-blocked *
Look to the next page for a computer simulated response chart showing the reduc-
tion of upper bass when adding a port-plug to your SVS (along with additional
woofer excursion needed to maintain lower frequencies). The bottom line? Many
customers feel the slight loss in upper bass output to be insignificant compared to the
deeper response the port block gives. We let you decide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 16
Bassy demo scenes to die for.
So now what?? You’ve got one of the best theater and music bass sub-
systems on the planet, you’re calibrated...want to see what she’ll do?
But of course! Since finding those scenes can be a bit trying, we’ve
compiled a list of our old favorites below. After all, calibration with test
tones is important, but it’s movies and music this sub is itching to show
off. Chapter stops for DVDs are shown, with movie time in hours: min-
utes: seconds. What are you waiting for? Just hit PLAY!
•
“The Iron Giant” Great family animation with SERIOUS bass,
including strong peaks below 25 Hz. Jump to:
1. “Chase thru the forest” Scene 8 (20:00 into the movie)
2. “Robot Landing” (Train Impact) Scene 10 (25:40)
3. “Green Boom” Scene 27 (1:11:40)
•
•
“Antz” Another good family movie, though not perhaps for small
children. Extremely loud bass above 30 Hz.
“Terror from Above”, Scene 17 (51:48)
“The Matrix” Modern, violent, science fiction classic with plenty
of shoot-’em-up bass blasts. Here’s some subtle and not so subtle.
1. “Where we are grown”, Scene 12 (42:55)
2. “Landing in fight”, Scene 15 (50:51)
3. “Chopper shootout”, Scene 31 (1:47:15)
•
•
“Das Boot” Arguably one of the most compelling war pictures of
all time with bass approaching 20 Hz. Very loud, very deep.
1. “Depth charges”, Scene 21 (59:30)
2. “Storm surfing”, Scene 25 (1:15:15)
3. “Hitting bottom”, Scene 17 (53:15, Side “B”)
“Apollo 13” Moving story, with some surprisingly subtle but re-
vealing bass where it counts.
1. “Lift off”, Scene 13 (35:15)
2. “Coming home”, Scene 53 (2:05:43)
Download from Www.Somanuals.com. All Manuals Search And Download.
SVSound
Page 17
More Bassy demo scenes.
•
“Titanic” You love it...or you hate it. Regardless of which side
of the ship you sit on, this flick does some serious rumbling for
you:
1. “We can’t leave him” Scene 22 (2:21:50)
2. “Ship Splitting” (2:41:30)
3. “Last Gasp” (2:42:05)
•
•
“Blade” Not one for the kiddies, but loaded with deep bass.
1. “Footstep”, Scene 4 (7:15)
2. “Door blown” Scene 20 (50:05)
“Aliens” Not just another modern sci-fi horror classic, this one
rocks from intro to final scene.
1. “Ship drop”, Scene 9 (41:20)
2. “Awakenings”, Scene 15 (1:12:52)
•
"Apocalypse Now" Making This Vietnam war movie, Francis
Ford Copolla nearly went crazy...imagine what it'll do to your
subwoofer!
1. "Chopper ride" Scene 2 (0:19:47)
2. "ARC LIGHT" Scene 4 (0:26:02)
3. "Grenade launch" Scene 12 (1:27:58)
“Contact” SETI with a (bass) twist or two along the way.
1. “Bombing”, Scene 28 (1:36:30)
•
•
2. “Space truckin”, Scene 33 (1:55:56)
“Dark City” One of Roger Ebert’s favorites, think he likes bass
too?
1. “Let the tuning commence”, Scene 8 (34:30)
2. “City makeover”, Scene 15 (1:27:45)
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 18
Authorized International Dealers:
Australia/New Zealand
Deep Hz Audio
BENELUX
M-Pro BVBA
98 Nimblefoot Way
De Regengoog 3
Lilydale Vic. 3140, Australia
Phone: 0434-550782
Email: [email protected]
2800 Mechelen, Belgium
Phone: +32 (0)15-330980
Fax: +32 (0)15-330995
Email: [email protected]
Canada
Sonic Boom Audio
Scandinavia/Germany
L-Sound AS
410 Denison street
Bedriftsveien 14
Markham, Ontario
Phone: (905) 944-8484
Email: [email protected]
4841 Arendal, Norway
Phone: (+47) 377 11 333
Fax: (+47) 377 10 440
Email: [email protected]
UK
South America
Liquid Sound Ltda
Kent Home Cinema/AV-Sales
69 London Road, Southborough
Tunbridge Wells, Kent
TN4 0PA, England
Phone: 01892 535007
Fax: 01892 533334
Email:
Rua Dario Pompeu de
Camargo, 467
13089-080 Campinas, Brasil
Fone: +55 (0)19-9276-8820
Fax: +55 (0)19-3251-4482
Email: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
SV Sound
Page 19
Notes:
Download from Www.Somanuals.com. All Manuals Search And Download.
Terms and Conditions
Terms and Conditions: Further explanation is yours at any
time. Contact your Dealer listed on the previous page. Please
note that these terms and conditions do not affect your statutory
rights.
Shipping: When you receive your new subwoofer, please
check to ensure there is no damage. If after unpacking you
discover any damage that may have been caused by transporta-
tion on your product, we request you contact your Dealer im-
mediately and if possible, provide a photo of damage in ques-
tion to them to ensure the fastest possible correction to the
situation.
Warranty: The product has a 3 year warranty against defects
in materials and workmanship. Upon return, the products will
be repaired and redelivered. Naturally, this warranty does not
cover any product subjected to misuse or accidental damage.
The bottom line: We’re proud of these subwoofers and want
you to be as happy owning one, as we are selling one (or more)
to you. E-mail your Dealer or SVS if you have any warranty
question.
Download from Www.Somanuals.com. All Manuals Search And Download.
|