User’s Guide
Ⓒ 2010 Sonostar Inc.
V.350.03_E
Download from Www.Somanuals.com. All Manuals Search And Download.
your computer.
Accessories: You should have received the
following items with your Sonocaddie package:
Sonocaddie V350/ V350 Plus, Mini USB Cable,
Rechargeable Battery, User’s Guide, Quick Guide,
Belt Clip, AC Charger Wall Adaptor, and Carry
Pouch.
Important Notice: Please read and follow the
guidelines below. Failure to do so may result in
misuse of the equipment and may be dangerous or
illegal. Should you experience any problems with
your Sonocaddie (e.g. malfunction/damage), please
contact Sonocaddie Customer Service at
on your own as this may void the warranty.
Warnings:
¾
Sonocaddie performs best under a clear sky
and with six satellite signals. Environmental
factors (such as rain, dense clouds, fog, solar
flares, high voltage electricity, cellular phone
towers, etc.) may adversely affect the GPS
reception. If the device is indicating less than
six satellite signals, the Sonocaddie
performance may not be optimal until the
conditions change for better reception.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
Sonocaddie should not be used while driving
any vehicle including golf carts. Always place
Sonocaddie in a secure place to avoid any
impact which could cause damage to it.
The USB cable provided is solely for the use
of Sonocaddie devices (see the accessory list).
Do not connect any other cable for data
transfer as this could damage the data port
(I/O port) on the V350 Series.
¾
¾
A full battery charge may take up to four
hours, however, you should NOT charge
device over 8 hours.
If you do not plan to use the device for a long
period of time, please remove the battery to
avoid the battery leaking and corroding the
battery case.
Cautions:
¾
¾
The Sonocaddie may take at least 10-15
minutes to receive satellite signals after you
turn it on. This may take longer if the device
has been off for more than four hours, or if it
is more than 100 miles away from where you
last used the Sonocaddie.
The Global Positioning System (GPS) is
operated by the government of the United
States, which is solely responsible for its
3
Download from Www.Somanuals.com. All Manuals Search And Download.
accuracy and maintenance. The system is
subject to changes which could affect the
accuracy and performance of all GPS
equipment.
¾
¾
Sonocaddie has a built-in GPS antenna at the
top of the device. This antenna should face
upward to gain the best signals and should not
be covered with anything as this may affect
the quality of reception and accuracy of the
device.
Trees and/or buildings may adversely affect
coverage/reception levels and accuracy.
Optimal performance will occur by staying in
wide open areas.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 - Getting Started
Chapter 2 – Introduction
2.1 Sonocaddie Features
2.2 Navigation
2.3 Sonocaddie V350 Series Main Screen
2.3.1 Menu Items (The applicable chapter
sections are noted in parenthesis.)
2.3.2 Screen Display Items
8
10
11
12
12
13
14
15
Chapter 3 - Before Starting a Game
3.1 Adjust the Sonocaddie V350 Series Settings15
3.2 Install Sonocaddie V350 Series Software 16
3.2.1 Register Your Membership & Unlock
Unit
19
21
3.3 Download Course
3.3.1 Manage Data in V350 Series Software
22
Chapter 4 – Starting a Game
4.1 Start with Existing Courses
4.1.1 Course Auto Search
23
24
24
4.1.2 Search Courses from Course List 26
4.2 Select the First Hole 27
4.3 Understanding the Hole-Layout and Hole-Info
Screens
27
30
4.4 Carrying the Sonocaddie V350 Series
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Using the Sonocaddie V350 Series
during a Round
5.1 View the Green Close-Up
5.2 Track Your Game Feature
5.2.1 Shot Track
30
31
32
33
34
35
36
38
39
40
43
43
5.2.2 Auto Track
5.3 Measure your Shot Distance
5.4 Use the Digital Scorecard
Chapter 6 – Editing an Existing Course
6.1 Understanding the Edit Screen
6.2 Edit an Existing Target on a Hole
6.3 Add a New Target to a Hole
6.4 Delete a Target on a Hole
Chapter 7 – Managing Course Information on the
Sonocaddie V350 Series
7.1 Delete a Course
7.2 Rename a Course
7.3 Create a New Course
7.3.1 Name the New Course
44
44
45
46
46
7.3.2 Map the Targets on the New Course 47
Chapter 8 – Review Stored Information after the
Round
8.1 Use the Sonocaddie V350 Series to Review
Information 50
50
8.1.1 Review Prior Scorecards and Tracks 50
8.1.2 Delete Prior Scorecards and Tracks 51
6
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2 Use the V350 Series Software to Review
Information
51
8.2.1 Manage Course Information under the
MyCourse Tab
54
8.2.2 Manage Course Information under the
MyFolder Tab
Appendices
Frequently Asked Questions (FAQs)
Regulatory Agency Compliance
54
56
57
62
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - Getting Started
Before using the Sonocaddie V350 Series for the
first time, charge the battery for at least 4 hours.
Under normal conditions, a full battery charge may
take up to 4 hours if the device is turned off, and
longer if it is turned on for use. To charge the V350
Series, remove the back cover and insert the
supplied rechargeable battery correctly as shown.
Warning: We recommend that you never charge
the device over 8 hours.
Locate the
charging/data port on
the right side of the
V350 Series, pull out
the rubber cover, and carefully insert the mini-end
of the supplied USB cable into the port. Connect the
other end of the cable to the USB port on your
computer. (Fig. 1, 2)The screen indicates that the
device is charging and also when it has reached a
full charge. You can also charge the device with the
supplied AC Wall Charger Adapter or an optional
12V Car Adapter (Fig. 3).
The battery should last approximately 8~12 hours
under normal operation. Please note that using
8
Download from Www.Somanuals.com. All Manuals Search And Download.
longer “Backlight” durations in the Settings will
drain the battery quicker. You can confirm the
remaining battery level with the V350 Series
on-screen battery gauge.
(Fig. 1, 2)
(Fig. 3)
Scale of power
Conditions
Full
Empty
Register Your Membership & Unlock Unit
Important! (For V350 unit only)
Please register your membership once you
received Sonocaddie V350. The unit will be
locked after turning on five times and remain its
status until your registration completed. To
unlock V350 you must login V350 software with
9
Download from Www.Somanuals.com. All Manuals Search And Download.
the unit connected.
Sonocaddie V350 can be operated without
registration for the first five times under Basic
View (icon mode) only. For any other color
course layout downloads, please register and
upgrade your membership.
Chapter 2 – Introduction
The Sonocaddie V350 Series has many unique and
useful features to help you earn your best scores
ever as shown below. The Course Layout is a
patented color view of each hole that allows you to
see your exact position on every hole in real time
and the precise distances to critical targets. The
Green View displays a full green image with
distances to the front, middle and back of the green.
The Edit and Map functions let you quickly
customize or create a golf hole right on the spot. The
Mark function provides an easy way to quickly
measure the distance of any shot. The Track Shot
function gives you the ability to record your shot
locations from anywhere on the course for review
later. And the Scorecard feature provides a digital
scorecard for each course and the “Pro” Scorecard
gives a full analysis of each round. The V350 has
enough memory to store 100 different golf courses,
10
Download from Www.Somanuals.com. All Manuals Search And Download.
record 100 scorecards, and track the golf shot
locations for up to 100 rounds.
2.1 Sonocaddie Features
① Power button
② Scorecard button
③ Left soft key
④ Right soft key
⑦
⑧
5-way key:
Left/Right/Up/Down/
Select & Save
Mini-USB Cable &
Charging Port
⑤ ESC/ back to the
⑨
⑩
⑪
GPS Antenna
Belt Clip Hook
Battery Cover
previous screen.
⑥ Mark button
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Navigation
Navigating the Sonocaddie is simple. All functions
are available from the main screen using the front
panel soft keys. In addition, the left and right side
buttons provide a quick way to access frequently
used features.
z 5-Way Key – use the 5-Way key (#7) to move the
screen cursor and select menu items. Press the
up/down or left/right arrows to scroll the cursor
around the screen and press the center key to
execute a highlighted selection.
z Front Panel Soft Keys – use the right soft key (#4)
or use the left soft key (#3) to select the action
shown directly above those keys. Use the Escape
key (#5) at any time to return to the previous
screen, or hold it down for three seconds to return
to the MAIN screen. Press the “Mark” button (#6)
to measure your shot length.
z Side Buttons – side buttons provide access to
popular functions. Press the left “Scorecard”
button (#2) to instantly bring up a digital
scorecard.
2.3 Sonocaddie V350 Series Main Screen
To turn on the Sonocaddie V350 Series, press the
top left-side Power button (#1) for at least 3 seconds.
After a few seconds, the “MAIN” screen below
appears on the device. To turn off the Sonocaddie,
12
Download from Www.Somanuals.com. All Manuals Search And Download.
press the Power button again for 3 seconds, or select
“OFF” from the “MAIN” screen. When the
“Shutdown Now?” screen appears, press “YES”
with the right soft key.
Satellite Signal
GPS Status
My Course
Off
MAIN
Record
Battery Level
Settings
Auto Search Course List
Mark
Info
Time Display
Menu Text
Right Soft Key Action
Left Soft Key Action
2.3.1 Menu Items (The applicable chapter sections
are noted in parenthesis.)
y
y
GPS Status: Use this feature to get detailed
information about satellite reception.
Record: Use this feature to view all the shot
locations by hole or scorecard records that
you recorded during a game. (8.1)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
y
y
y
Settings: Use this feature to customize the
Sonocaddie settings to your individual
preferences. (3.1)
My Course: Use this feature to select a course
to play from the list of courses you
downloaded. (4.1)
Auto Search: Use this feature to search the
available courses in the specific distance.
(4.1.1)
y
y
y
y
Course List: Use this feature to search the
courses by COUNTRY or HISTORY. (4.1.2)
Off: Use this feature to turn off the Sonocaddie.
(2.3)
Mark: Use this feature to measure the distance
of any shot. (5.3)
Info: Use this feature to review the software
version number for the Sonocaddie.
2.3.2 Screen Display Items
y
y
y
Satellite Signal: Displays the current number
of satellites the Sonocaddie is receiving.
Battery Level: Displays the amount of battery
life remaining.
Time Display: Displays the current time on the
Main Screen only.
Soft Keys: Displays the action that is available by
selecting the right or left soft key.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Before Starting a Game
3.1 Adjust the Sonocaddie V350 Series Settings
The Sonocaddie has ten settings to customize your
device. Follow these steps to change the settings;
1) Select “SETTINGS” from the “MAIN” screen.
2) Press the up/down buttons on the 5-way key to
scroll down through each setting.
3) Press the left/right buttons on the 5-way to scroll
through the available options for that setting.
4) To exit the screen without changing the settings,
press the “ESCAPE” key on the front key pad.
5) To save settings, press center key on the 5-way
key, or select “SAVE” with the right soft key.
6) To return to the default factory settings, press
“RESET” with the left soft key.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. LANGUAGE: English/ French/ Deutsch/
Spanish / Japanese/ Traditional Chinese/
Simplified Chinese
2. TIME ZONE: Please choose your correct time
zone
3. DISTANCE UNIT: YARD / METER/ MILE/
KILOMETER
4. THEMES: BLUE / PURPLE/ GREEN/
ORANGE
5. BRIGHTNESS: OFF/1/2/3/4/5
6. BACKLIGHT TIME: ALWAYS/ 15sec/
30sec/ 60sec
7. AUTO TRACK: ON /OFF
8. TRACK INTERVAL: 10sec / 20sec/ 30sec
9. AUTO HOLE: ON/ OFF
10. SCORECARD: NORMAL / PRO
3.2 Install Sonocaddie V350 Series Software
This application software is used for you to access
and download course information and manage your
V350 Series personalized course folder. Please
install it from enclosed CD or from website at
Microsoft Windows 7, XP and Vista.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions:
Step 1. Please shut down all other programs and
insert Sonocaddie V350 Series software disk to
install.
Step 2. Follow the instructions on setup wizard to
finish the installation.
Step 3. Once the installation has
finished, please go to the desktop and
click on the Sonocaddie V350 icon.
*Note: If your operating system is Windows Vista or
Windows 7, please follow the instructions
below for additional settings.
1. After your installation has completed, please
enter C: / Program Files/ Sonocaddie V350 Series
2. Please right click on the V350 Series.exe icon and
click on shield symbol “Run as administrator” to
adjust the original setting.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Go back to the desktop and click on the
Sonocaddie V350 Series icon to proceed the
software.
Step 4. The box below will appear if a newer
software version has been released. Click YES to
update to the latest version.
3.2.1 Register Your Membership & Unlock Unit
18
Download from Www.Somanuals.com. All Manuals Search And Download.
*Note: You may use your V350 five times before
you must register your membership. After five
uses the V350 unit will be locked and remain in
locked status until your registration is completed.
To register and unlock V350 please follow the
instructions below.
Step 1. After the software has been updated, please
complete the Membership Registration form on
screen. The email address
you entered will
be your login ID.
(Note: Product
serial number
underneath the
battery is
required for the
registration.)
Important!
Serial Number (S/N) is required to join Sonocaddie
V350 Series membership.
Step 2. When Sonocaddie Login Screen appears,
please power up the device and connect it to your
computer with USB cable.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Log into the software with your email
address & password, and the V350 Series
Management Screen will soon appear.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4. All registration and unit unlock process (for
V350 unit only) will have been successfully
completed when you see the bar running between
the graphics of device and PC.
3.3 Download Course
Step1. Log in membership to enter V350 Series
Software.
Important!
Internet connection is required to log in V350 Series
Software to access course data. It is required to fill in
the email account and password to run V350
Software. They are same with the account you
registered your member account.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.1 Manage Data in V350 Series Software
A. Information bar: User’s name/ Type of
Membership Plan/ Membership Valid Period/
Registered Country
B. SonoCourse Tab:
Links to Sonocaddie database for downloading
course data. Steps to download course data:
Step 1.Please select the Country and State, enter the
Course Name then press “GO” for the course you
want.
Step 2.Check one or more boxes beside each course
22
Download from Www.Somanuals.com. All Manuals Search And Download.
you wish to download, and press “Download↓＂
button to transfer the course(s) to your Sonocaddie
V350 Series.
C. My Course:
When linking with V350 Series device, the course
data/ scorecard record(s) on the device is ready to be
uploaded, deleted and reviewed (scorecard record
only).
Upload: You can upload the course GPS (up to 30
courses) and Scorecard (up to 100 records) data to
“My Folder” tab.
Delete: Tick one or more box of data, press
“Delete” button to remove the data.
Review: (scorecard only): Review scores and
analysis of your round(s).
Chapter 4 – Starting a Game
Before you leave for the course, make sure the
Sonocaddie V350 Series is fully charged. When you
arrive at the course, immediately turn the device on
because acquiring satellites can take up to 15
minutes. The Sonocaddie V350 Series performs best
under clear skies so the better the satellite reception,
the better the device performs as the chart below
shows.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite signal
0～2
Accuracy
None
Poor
3～5
Fair
5～6
Good
6～8
Very good
Optimal
8～10
>10
Tip: Selecting “SATELLITE” from the “MAIN’
screen displays a screen with detailed satellite
reception information. Refer to the Appendix at the
end of this guide for an explanation of this screen.
4.1 Start with Existing Courses
4.1.1 Course Auto Search
Select “AUTO SEARCH” from the “Main” menu
to enter the searching function. Select a range from
5 miles to 50 miles, and all courses within the area
will be displayed. The nearest course will be on top
of the list. (NOTE: If a course is not displayed, it is
not in your Sonocaddie V350 Unit. See Section 3.3
to update your course list, or 7.3 to self map a
course, or contact [email protected]
to have us to map this course for you.) Press
“More” to select the course you want to play or
24
Download from Www.Somanuals.com. All Manuals Search And Download.
arrange the order of courses by distance or by
course name.
You must select a COURSE and a HOLE first. Then,
SCORECARD function and REFERENCE POINT
function can be used.
(Note: This function can only be activated when
there is GPS reception.)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.2 Search Courses from Course List
Select “COURSE LIST” from “Main” menu to enter
the searching function. There are two methods for
you to search your course from available courses
preloaded in the device:
1. By Country: All the courses are listed by country.
You can find your course by selecting “Country”,
“State” and “City”. Press “SEARCH” button after
every selection, then you will see all the available
courses within the area.
2. By History: Previous play will automatically add
to COURSE LIST sorted by history. This function
can memorize the last 30 courses.
Download from Www.Somanuals.com. All Manuals Search And Download.
For above two functions to search the course, if you
want to edit the selected course, by pressing
“COPY”, the selected course will be copied into
MY COURSE for you to edit the reference points.
4.2 Select the First Hole
First you must select the starting hole manually. The
“Auto-Hole” feature then automatically advances
the device to the next hole when you finish a hole
and enter the next tee box. Note that Auto-Hole can
be set to off from the Settings screen (see Chapter
3.1).
4.3 Understanding the Hole-Layout and
Hole-Info Screens
After selecting the first hole, the “HOLE-LAYOUT”
screen below appears displaying distances to targets
on a full-color, graphical view of the actual hole.
The distances constantly change as you move and a
“Walking Golfer” symbol also moves to show your
actual location on the hole. In addition, a second
“HOLE-INFO” screen is available with the same
distance information except it shows the targets on
the hole without the layout view. To access the
“Hole-Info” screen, select “MORE” with the right
soft key and “INFO.” There are 15 different icons
(or targets) available for this screen. Note that the
27
Download from Www.Somanuals.com. All Manuals Search And Download.
green-side icons on the Hole-Info screen are visual
markers only and provide no distance reading. To
return to the Hole-Layout screen, select “MORE and
“LAYOUT” with the right soft key. Also selecting
“GREEN” with the left soft key displays the full
green.
Important: If a Color Layout for a specific course
is not yet available from Sonocaddie, the device
displays the “Hole-Info” screen by default.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Status explanation
Bunker Front/ Back
Symbol
Water Front/ Back
(includes major water
hazards)
＊2nd Green Front/ 2nd
Green Back
Creek (includes: river,
ditch and stream)
Trap
Tree (includes: shrubbery
and forest)
Hills
Lay-up area
Out of Bounds (OB)
Delete
Dogleg Left/ Right
Rock
＊ Note: For some courses that have two greens on
one hole these icons provide distance for the extra
green.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Carrying the Sonocaddie V350 Series
Conveniently attach the belt clip to your belt or
clothing. Slide the hook on the back of the
Sonocaddie V350 Series into the clip until you hear
a “click” sound. To remove the Sonocaddie, press
the button on top of the clip down and slide
Sonocaddie upward out of the clip. You can also
attach the clip to different things, such as a golf bag.
The Sonocaddie V350 Series may also be mounted
to a golf cart with optional golf cart mounts (visit
Sonocaddie website for product information).
Important: Please make sure the belt clip or mount
is securely fastened and the Sonocaddie is firmly
attached for maximum
security.
Chapter 5 – Using the Sonocaddie V350 Series
during a Round
Now that you have set up your device, and selected
30
Download from Www.Somanuals.com. All Manuals Search And Download.
a course to play, you are ready to start using all
these features. When you are playing a hole and you
need the distance to the green or other targets simply
pull out your Sonocaddie V350 Series to see all the
distances you need on its color screen.
Tip: Hitting any key on the device turns on the
screen backlight feature on for easier viewing.
5.1 View the Green Close-Up
The Green Close-up view displays a full putting
green and provides five distance readings for each
green. It shows the distance to the front, center and
back of the green. In addition, the center reading
automatically changes to show an approximate
distance to a short and long pin location. To access
this screen, select “GREEN” with the left soft key.
To return, press “FULL” with the left soft key or the
“Escape” key.
Tip: To stop the auto-scrolling
feature, press the up or down
button on the 5-way key. Then
press either key again to scroll
the ball manually to find your
ideal spot.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
590
580
570
560
550
Distance from back of the green
Far landing zone
Center landing zone
Near landing zone
Distance from front of the green
Green Close-Up
5.2 Track Your Game Feature
The Sonocaddie V350 Series has two features to
track your game; “Shot Track” records your specific
shot locations and “Auto Track” automatically
tracks your route around the course. You can then go
back at a later time and review your stored Tracks
from your Sonocaddie V350 Series on the full-color
graphical display of the hole as shown below (See
Chapter 8 – Reviewing Store Information after the
Round) This way you can compare your
performance from game to game at your favorite
course, analyze your play like the pros, and learn
your strengths and weaknesses so you can adjust
your strategy for practicing and playing a course.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: Shot Track and Auto Track only work if
the course has a “Color Layout” and you are
located on a particular hole on that course with the
Walking Golfer symbol visible on the screen.
Auto Track &
Shot Track
Shot Track Only Auto Track Only
5.2.1 Shot Track
Shot Track remembers all the ball locations that you
enter on each hole on the Hole-Layouts. Simply
stand near the position of your shot and press
“SHOT TRACK” with the right soft button of the
Sonocaddie V350 Series. Shot Track internally
records this exact ball location on the Hole-Layout
screen for that hole so you can review at a later time.
Each time you want to record a new shot location,
press the “SHOT TRACK” button. The device
stores the shots for up to 100 rounds, however, it
can only store one round per day.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.2 Auto Track
When set on, Auto Track automatically records your
actual route around on the course on the
Hole-Layouts as you play. Auto Track can be very
useful when used with Shot Track above. To turn
Auto Track on, go to the “SETTINGS” screen,
scroll down to “AUTO TRACK”, and choose “ON”
with the left-right 5-way key. To set the interval
period for recording your position, scroll down to
“TRACK INTERVAL”, choose the desired interval,
and then press “SAVE” with the right soft key to
save these settings. Once you select a course to play
and Sonocaddie begins to receive satellite signals,
Auto Track immediately starts recording your route
on the Hole-Layouts. The device stores up to 100
rounds, however, it can only store one round per
day.
Important: Selecting different intervals for Auto
Track will affect the recording time for a round.
TRACK INTERVAL
10 SECONDS
Recording Period
5 hours
20 SECONDS
11 hours
30 SECONDS
16 hours
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Measure your Shot Distance
The “Mark” feature provides a simple way to
quickly measure the length of any shot you make by
measuring the distance between the start and end
positions of the shot. It is available anytime, except
when you are on the Green Close-up screen. There
are two ways to access this feature. The quickest
way is to press “MARK” with the bottom button on
the front panel soft key of the Sonocaddie V350
Series, or select “MARK” from the “MAIN” screen.
Important: To use “Mark”, you must be on the
course and the Sonocaddie must have satellite
reception.
To measure your shot, stand near where you hit your
ball and press the “MARK” button and the Mark
screen below appears. Press “START” with the right
soft key and proceed to your ball. The distance
displays “0” and changes as you move. You do not
have to travel in a straight line to the ball since the
device always measures the distance from the
starting position to your current location in straight
line. When you reach the ball, press “END” to lock
the number and see the actual distance of the shot.
To measure another shot, press “START” again.
Press the left soft key or the Escape key to return to
the previous screen.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ta
5.4 Use the Digital Scorecard
The Sonocaddie V350 Series provides a digital
scorecard to score your personal round and can
display an analysis of your round. Two types of
scorecards are available. The “NORMAL”
scorecard records your strokes only by hole and
provides a total for the front nine (out), back nine
(in) and 18-hole round. The “PRO” scorecard
records your strokes, putts, fairways hit, and sand
saves by hole. The Pro Scorecard also gives you a
full analysis of your round. Both scorecards
automatically display the “Par” (P) for whatever
hole you are playing.
The Normal scorecard is the default. Press the
“SCORECARD” button on the left side of the
Sonocaddie V350 Series and the Normal scorecard
below appears. Scroll across to the “Strokes”
column (S) with the left-right 5-way key and use the
36
Download from Www.Somanuals.com. All Manuals Search And Download.
up/down key to enter your strokes. Press the
“Escape” key to go back and Sonocaddie
automatically saves your scores, even if you turn it
off.
To make the Pro scorecard your default, go to the
“MAIN” screen, select “SETTINGS”, scroll down
the list to “SCORECARD”, choose “PRO” with the
left-right 5-way key, and press “SAVE” with the
right soft key.
To record your score on the Pro Scorecard, press the
“SCORECARD” button on the left side of the
Sonocaddie V350 Series and the Pro scorecard
below appears. Scroll across each column one by
one and use the up/down key to enter your Score (S),
number of Putts (Pt), and either Yes (Y) or No (N)
for both the “Fairway Hit” (Fw) and “Sand Save”
(Sd) column. To view an analysis of your round,
press “ANALYSIS” with the right soft key.
Important: For the Sonocaddie to accurately
calculate Greens in Regulation (GIR), you must
enter the Strokes (S) and Putts (Pt) for every hole.
Fairway and Sand Save percentages automatically
calculate according to your scores and the Yes/No
response you entered on each hole.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal Scorecard
Legend
Pro Scorecard
Hole (H)
Par (P)
Score (S)
Putt (Pt)
Fairway (Fw)
Chapter 6 – Editing an Existing Course
With the Sonocaddie V350 Series, you can also
make instant changes to the given course
information right on the spot. Courses are constantly
changing and sometimes a target may have moved
since the GPS setting was recorded. Or maybe you
have specific targets you like to use when you play
38
Download from Www.Somanuals.com. All Manuals Search And Download.
certain courses or you notice that a distance reading
is slightly off. With the Sonocaddie V350 Series,
you can change the course information on the go to
suit your own preferences so you will always be
playing with the most accurate and up-to-date
distances.
6.1 Understanding the Edit Screen
The information on each “Hole-Layout” screen or
“Hole-Info” screen originates from an “EDIT”
screen where specific GPS reference points (or
targets) have been recorded for that hole. To view
the Edit Screen, select “MORE” with the right soft
key and “EDIT.” Each target shown on a hole was
recorded on a blank Edit Screen. The Edit Screen
has eight available rows to locate GPS targets for
distance readings; six for on/off fairway targets and
two for the front and back green targets. Each row
has three GPS locations to record a target (left side,
fairway, and right side) and there can only be one
target per row. There is one GPS target location for
the front of the green and one for the back. Note that
the green center is actually calculated by
Sonocaddie based on the recorded front and back
points. Each green has two additional green-side
targets to display a visual marker. These do not give
a distance reading, nor do they appear on the
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Hole-Layout screen since this view already provides
a full-color, graphical view of the hole.
Hole-Layout Screen
Hole-Info Screen
Edit Screen with Targets Blank Edit Screen
6.2 Edit an Existing Target on a Hole
The Edit feature is available any time you are
playing a hole from the “Hole-Layout” screen or
“Hole-Info” screen. If you need to correct a distance
reading or want to change a given target on the hole
while playing, simply follow the edit process below.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat the process anytime you need to change or
update a target.
Important: To use the Edit feature, you must be on
the course and the Sonocaddie should have good
satellite reception (six or more satellites).
Step 1: Select “MORE” with the right soft key and
then select “EDIT” to view the Edit Screen.
Step 2: Stand at the target on the course that you
want to correct or update. Using the 5-way key,
scroll to and highlight the specific target icon on the
Edit Screen that you are correcting or updating.
Note the target distance reading may disappear
when you are standing within 5 yards of the target.
Step 3: Press “SELECT” with the right soft key to
access the “Target Icon” screen. Scroll to the icon
you want to record for that hole (refer back to
Chapter 4.3 for icon definitions). If you are
correcting a distance reading, select the same icon
that you selected previously on the Edit Screen. If
you are changing the target, select a new icon which
is more appropriate.
Important: Before pressing “Record”, be sure you
stand still for five seconds at the target location so
the Sonocaddie can pin-point that position. After
41
Download from Www.Somanuals.com. All Manuals Search And Download.
you select record, the distance reading changes to
“0” to indicate an accurate location.
Step 4: Press “RECORD” with the right soft key to
insert the icon on the Edit Screen and update this
position permanently in your Sonocaddie V350
Series. The distance immediately changes to a “0”
reading. If it does not, stand still and press “Record”
again from the same position.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 Add a New Target to a Hole
To add a new target, follow the editing steps above,
except in Step 2 stand at the new target on the hole
and scroll to one of the three available locations in
an empty row. Then follow Steps 3 & 4 to select and
record a new target on the hole.
Tip: To make reading distances on Hole-Layout or
Hole-Info screens easier, be sure to record targets
on the Edit Screen in the same order they appear
on the hole. Also if you add a new target to a row
that already has one, the old target will disappear
from the screen and the new one will appear
instead.
6.4 Delete a Target on a Hole
If you don’t want a specific target that has been
recorded on a hole, deleting it is simple and you
don’t have to be on the course. From any hole on the
Sonocaddie V350 Series, select “MORE” with the
right soft key and “EDIT” to view the Edit Screen.
Scroll to and select the Target Icon you want to
delete. When the “Icon Screen” appears, select the
“Delete” icon and press the right soft key. The target
disappears from the hole.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 – Managing Course Information on
the Sonocaddie V350 Series
With the Sonocaddie V350 Series, you can easily
rename or delete any course, or map targets for a
new course.
7.1 Delete a Course
From the “MAIN” screen, select “MY COURSE” to
see the Course List screen. Select a course and press
“MORE” with the right soft key to see the pop-up
44
Download from Www.Somanuals.com. All Manuals Search And Download.
list of options. Select either “DELETE” to delete the
selected course or “DELETE ALL” to delete all
courses in the course list. After the “Delete
Course?” confirmation screen appears, select “YES”
with the right soft key to confirm, or “NO” with the
left soft key to go back. Selecting “YES”
permanently deletes all the course information and
targets for that course.
Important: Deleting a course does not delete any
Scorecards or Tracks stored in the Sonocaddie for
the deleted course so you can still review these at
any time (See Chapter 8 – After the Game).
7.2 Rename a Course
From the “MAIN” screen, select “MY COURSE” to
see the Course List screen. Select a course, press
“MORE” with the right soft key and select
“RENAME” from the pop-up list. Use the 5-way
45
Download from Www.Somanuals.com. All Manuals Search And Download.
key with the screen keyboard to scroll back through
the course name and edit it. After renaming the
course, select “RECORD” with the right soft key to
save the changes.
7.3 Create a New Course
Creating a new course map works just like the edit
process in Chapter 6.2, except the Edit Screen is
blank when you start. By following the steps below,
you can create your own custom layout for any hole
on a new course. You can only view a new course
using the “Hole-Info” screen and you must be on the
course to map the targets.
7.3.1 Name the New Course
To create a new course, select “MY COURSE” from
the “MAIN” screen and press “MORE” with the
right soft key and select “NEW” from the pop-up
list to view the keyboard screen. Enter a new course
name using the 5-way key to scroll the keyboard
46
Download from Www.Somanuals.com. All Manuals Search And Download.
and center key to enter a selection. The backspace
key (§) on the keyboard erases letters. When you
are finished, press “RECORD” to save the name.
After you save the new course name, the “Select
Hole” screen immediately appears. The new course
name also automatically appears on your course list.
7.3.2 Map the Targets on the New Course
Mapping a new course with the Sonocaddie V350
Series is easy. Simply repeat the following steps
each time you want to add a target to a hole for a
new course.
Step 1: Press “SELECT” with the right soft key for
the hole you are mapping and then select “EDIT.”
Step 2: Stand at the target you want to add on the
hole. Use the 5-way key to scroll and highlight an
empty location on the Edit Screen where you want
to record the new target. You can record one target
47
Download from Www.Somanuals.com. All Manuals Search And Download.
per row on the eight on/off fairway rows, one front
green location and one back location, and two
separate green-side icons.
Step 3: Press “SELECT” with the right soft key to
view the “Icon Screen” for targets. Scroll to the icon
you want to add for that hole and highlight it. (Refer
to Chapter 4.3 for Icon definitions)
Step 4: Press “RECORD” with the right soft key to
insert the target icon on the Edit Screen and
permanently add this GPS target position to the hole.
The icon now appears on the Hole-Info screen and
the distance to this location changes as you move
around the course.
Important: Before pressing “Record”, be sure you
stand still for five seconds at the reference point
location so the Sonocaddie can pin-point that
position. After you select record, the distance
reading immediately changes to “0” to accurately
record this location.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 - Green Targets: To set the front green
location, stand at the front of the green, select the
front green location on the Edit Screen, press
“RECORD” and a “0” reading appears. Move to the
back of the green, select the back green position,
and press “RECORD” again. The device
automatically calculates the center location based on
the front and back locations. To add a green-side
icon (which does not provide distance information),
scroll to either green-side location, press “SELECT”
to view the Icon Screen, choose the icon you want
to display and press “RECORD” to insert it.
Green Front
Green Back
Green-Side
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Review Stored Information after the
Round
If you used the Scorecard or Track features during
your round (see Chapter 5.2 & 5.4), you can review
this information anytime from your Sonocaddie
V350 Series device or upload it to your V350 Series
Software for review later (For scorecard only).
8.1 Use the Sonocaddie V350 Series to Review
Information
8.1.1 Review Prior Scorecards and Tracks
The Sonocaddie V350 Series stores scorecards/
tracks for up to 100 rounds and saves them until you
clear the score or delete the scorecard from the
device. The Sonocaddie stores scorecards by the
course name and date you played it.
To view a stored scorecard/ track, go to the “MAIN”
screen, select “RECORD” for a list of stored
scorecards/ tracks. Scroll down to the information
you want to view and press the right soft key. You
can even edit your scores from this screen after a
round in exactly the same way you did during a
round. If you used the Pro Scorecard, you can also
view a full analysis of your round by selecting
50
Download from Www.Somanuals.com. All Manuals Search And Download.
“ANALYSIS” with the right soft key. Note below
how the track views change depending on what
feature you used. Press the Escape key at any time
to return to the previous screen.
8.1.2 Delete Prior Scorecards and Tracks
You may remove a saved Scorecard/ Track from the
Sonocaddie anytime. From the “Main” screen select
“RECORD”, scroll down the list to the one you
want to delete, and press “DELETE” with the right
soft key. When the pop-up screen appears, select
“DELETE” to delete the selected item or “DELETE
ALL” to delete the entire list. When the “Delete
both track and scorecard?” confirmation screen
appears, select “YES” with the right soft key to
confirm, or “NO” with the left soft key to go back.
Important: Selecting “YES” deletes both the
scorecard(s) and track(s) from the Sonocaddie
V350 Series.
8.2 Use the V350 Series Software to Review
Information.
With the V350 Software on your computer, you can
view the same information that is stored in the
device or upload the information to MyFolder to
review anytime, even without your device. The
“GPS” and “Scorecard” buttons at the top of the
51
Download from Www.Somanuals.com. All Manuals Search And Download.
display provide different types of personalized
information and you can switch between these two
views simply by pressing either one of the buttons.
Tip: Anytime you click the GPS or Scorecard
button, the MyCourse tab and MyFolder tab both
automatically switch to that view at the same time
no matter what tab you are working in.
First access the V350 Software on your computer
and log in (refer to Chapter 3.2.1, Step 3). Turn on
your device and connect it to the computer with the
supplied USB cable. When you see the link message
on the V350 series (“USB cable connected - Enable
USB link now? ”), select “YES” with the right soft
key to connect the device to your computer, which
is indicated by an moving green bar on the V350
Software Display. Click the “GPS” button and look
under the MyCourse tab to see the courses that are
stored in the V350 Series.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2.1 Manage Course Information under the
MyCourse Tab
You can also use the software to manage the course
information that is stored in your Sonocaddie. To
delete a course, check the box beside the desired
course listed under the MyCourse tab and press the
“DELETE” button to the right of the tab.
To review a Scorecard record, click the
“SCORECARD” button at the top of the V350
Software screen. Check the box beside the desired
record under the V350 tab and press the “REVIEW”
button to the right of the MyCourse tab. Your scores
and analysis pops up on the main screen for that
round (as shown above). To delete a scorecard,
check the box beside the desired scorecard under the
V350 tab, and press the “DELETE” button to the
right of the tab.
8.2.2 Manage Course Information under the
MyFolder Tab
MyFolder stores personalized course information
that you transferred from your Sonocaddie V350
Series so you can review it anytime, even if your
device is not connected. To upload information to
MyFolder, select the “GPS” or “SCORECARD”
button at the top of the display. Check the box
54
Download from Www.Somanuals.com. All Manuals Search And Download.
beside the item(s) you want to upload and click the
“UPLOAD” button on the display. The information
immediately appears in MyFolder after the transfer
is complete. You can delete and review it in exactly
the same way that you did for the MyCourse tab
above. MyFolder can store 30 courses and 100
scorecards.
Important: Do not disconnect the cable between
V350 Series device and computer when uploading.
Also, you cannot directly upload courses from the
Sonocaddie database to MyFolder. You have to
download them to the MyCourse tab then upload
them to MyFolder.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
A. Specifications
• Size
H 116mm×W 57.8mm×T 20.9mm (H
4.6”×W 2.3”×T 0.8”)
• Weight
• Screen
119g ( 4.21 ounces)
2.2” high-resolution color LCD w/
Backlight
• Operating
Maximum 60 º C / 158 º F; Minimum -5 º
Temperature C / 23 º F
• Storage
Courses
My Course: 100
Scorecard: 100
Track: 100
• Battery
Rechargeable
o 8 to 12 hours in normal operation (may
vary with backlight duration)
o Charging Time: 8 hours in operation
mode, 3-5 hours in off mode
•Acquisition Approx 5~10 minutes
Rate Cold
Start
• Accuracy
3 Meters CEP (80%), 7 Meters CEP
(90%) horizontal, SA off
• GPS
Built-in High Sensitivity GPS Antenna
Receiver
• Durability
Waterproof, IPX3
B. Membership
For more detailed information, please refer to
56
Download from Www.Somanuals.com. All Manuals Search And Download.
C. System Requirement (Computer access not
required when self-mapping or Pre-loaded Courses.)
• XP/Vista/Windows 7
• CD-ROM
• 512 MB RAM (XP)
• 1 GB RAM (Vista) or higher
• 12 MB or more hard disk space
D. Abbreviations
B = Back
Lon = Longitude
P = Par
C = Centre
F = Front/Fairway
GIR = Green in Regulation
Pt = Putt
Sd = Sand trap
GPS = Global Positioning System S = Score
Lat = Latitude H = Hole
Frequently Asked Questions (FAQs)
You can also find answers to FAQs at the
Q1. What do I do when my Sonocaddie is not
detecting a signal?
Answer: The GPS unit must be used in open-sky
areas and away from buildings (such as club house),
57
Download from Www.Somanuals.com. All Manuals Search And Download.
deep forest, or cliff sides. Otherwise it won't receive
GPS signals and will show nothing on the display.
After power-up, a number/bar will appear on the
upper-left corner of the screen, which is the number
of satellites received. If showing "X", it means no
signal.
In addition, it takes several minutes to receive stable
signal after power-up even under an open-sky. If
there is still no signal, please check your battery life
displayed on the screen. As a last resort, try
restarting your Sonocaddie.
If you are on the course, all distance numbers will
automatically show on the screen. However the limit
of displayed yardage is 999 yards. Therefore any
distance beyond 999 yard will show 999 only. If the
unit shows "─ ─" when the satellite is available, it
means that the distance within 0~5 yards.
Q2. How can I track my driving distance?
Answer: Simply press a button to record the
beginning coordinates of your shot and the end
coordinates of your shot and Sonocaddie will
accurately calculate the shot distance. This is the
‘straight-line’ distance between the starting and end
points and does not take the shape of the fairway or
the shape of the shot into consideration. Please
consult the user guide for more details.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Q3. Can I connect my Sonocaddie to other
computer devices?
Answer: Apart from the computer systems approved
by Sonocaddie, we do not provide any assurances,
and advise against attempting to connect it to any
non-approved devices.
Q4. Why is the distance of the course marker
different from the distance measured by
Sonocaddie?
Answer:
1. First, please make sure that the distance unit
either in Sonocaddie or the course is the same (i.e.
“YARDS” vs. “METERS”). If they are different,
please go to “Settings” in main menu and select
“Yard” or “Meter” as the right unit.
2. Some courses measure the distances by using
laser equipment. If the Green and Tee box are not at
the same horizontal level, the yardage numbers
could be different from those of Sonocaddie. Most
Golf GPS devices measure the distance only in
horizontal level, which is more useful for golfers
than straight-line of laser unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. However, some courses measure the distance
from tee box to the green along the middle line of
fairway. For example, the distance on the tee mark
or scorecard shows 410 yards, but Sonocaddie only
shows 380 yards.
Q5. Will I lose my data when the power goes off
on my Sonocaddie?
Answer: The data you store in your Sonocaddie will
never be lost unless you edit or erase it on purpose.
Q6. Why are the distances shown on Sonocaddie
incorrect for each hole on this course?
Answer. Please check the GPS reception on the GPS
Status screen at the time to be sure you have at least
6 stable satellite signals. Also check the Settings
menu (Wrench icon) to be sure the distance units
60
Download from Www.Somanuals.com. All Manuals Search And Download.
(yard or meter) are correct.
In addition, the distance in GPS device is not related
with the locations of tee boxes. The distance is
calculated based on the difference between your
position (the “apparent” position) and the known
position. The apparent position is the moveable
location of the GPS device which receives the signal.
The known position is the position of the target or
reference point.
The known position is fixed and is the coordinates,
such as bunker and green, downloaded from the
database of the Sonocaddie website. Therefore when
you stand by the tee box (apparent position of GPS
device you carry), the unit will calculate the
distance between you and the green or known
position.
Q7. Can I connect Sonocaddie to Mac OS?
Answer. Sonocaddie is not compatible with Apple
Mac OS systems including X Leopard and Windows
XP under Virtual PC.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Agency Compliance
Federal Communications Commission (FCC)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
NOTICE The FCC warns that user modifications of
this device without the express approval of Sonostar
Inc. could void the user’s authority to operate the
device.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
|