GW-200 User Manual
GW-200 VoIP Gateway
User M anual
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Breif Introduction and how-to-start information
GW-200 VoIP Gateway functions as an analog adaptor with an
ordinary telephone. It has a power adapter interface, an RJ45 interface, an
RJ11 interface and an “IP/SET” key. RJ45 interface is used to connect to LAN
and RJ11 interface is used to connect the phone. The “IP/SET” key is to initiate
the voice prompt stored to announce the local IP address; to enter safe mode
to retrieve the firmware and to set the IP type and IP address.
To start, please connect your GW-200 VoIP Gateway with the LAN, a
phone and the power supply properly. (see the following picture)The GW-200
will boot up. It takes 30 seconds until the Gateway is in working mode. Please
press “IP/SET” key and pick up the phone’s handset, you should be able to
hear dial tone or busy tone. Now let us configure it.
1. If you are using DHCP IP addressing
Please pick up the phone, press 12341, then press the “IP/SET” key on
the gateway and hang up the phone. GW200 will then reboot and connect to
DHCP server to get the IP address. After 30 second, press the “IP/SET” key
and then pick up the phone, you will hear the voice prompt from the handset
telling you the current IP address of the gateway.
2. If you are not using DHCP IP addressing
If your LAN does not use DHCP addressing, each device concurrently connected to it
must be assigned its own unique IP address. To allocate an IP address for GW-200,
for example 192.168.1.100, please pick up the phone, press 12340, then
press the “IP/SET” key on the gateway and hang up the phone. After the
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
gateway has finished rebooting, it will be in static IP mode. Then you pick up
the phone again, press 1234 192*168*1*100, then press the “IP/SET” key on
GW-200 and hang up the phone. Gateway will reboot again. Now the phone’s
IP address is 192.168.1.100, if you want to check it, please refer to the item 1.
Features
Hardware
ꢀ Main chip—pa1688 50MHz
ꢀ Data Memory—2MB SDRAM
ꢀ Program Memory—1 MB Flash memory
ꢀ Ethernet Jack—10/100M jacks
ꢀ AC/DC adapter—Input AC 230V or 120V Output 9V DC, 500mA
Software
ꢀ DHCP support for LAN or Cable modem
ꢀ PPPoE support for ADSL or Cable modem
ꢀ Set phone by HTTP web browser (IE6.0) or Telnet
ꢀ Upgrade by FTP
ꢀ Support major G.7XX and gsm610 audio codec
ꢀ VAD(Voice Active Detect)
ꢀ CNG (Comfort Noise Generation)
ꢀ Dynamic voice jitter buffer
ꢀ G.168/165 compliant 16ms echo cancellation
ꢀ Tone generation and Local DTMF re-generation according with ITU-T
ꢀ E.164 dial plan and customized dial rules
ꢀ Voice prompt
ꢀ Hotline
Standard and Protocol
GW-200 supports following standard and protocol:
ꢀ IEEE 802.3 /802.3 u 10 Base T / 100Base TX
ꢀ Major G.7XX and gsm610 audio codec
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ꢀ TCP/IP: Internet transfer and Control Protocol
ꢀ RTP: Real-time Transport Protocol
ꢀ RTCP Real-time Control Protocol
ꢀ VAD/CNG : save bandwidth
ꢀ DHCP Dynamic Host Configuration Protocol
ꢀ PPPoE Point to Point Protocol over Ethernet
ꢀ DNS Domain Name Server
ꢀ Telnet Internet's remote login protocol
ꢀ FTP File Transfer Protocol
ꢀ HTTP Hyper Text Transfer Protocol
ꢀ Build in proxy
Operating requirements:
ꢀ Operation temperature: 0 to 50°C
ꢀ Storage temperature: -10°to 60°C
ꢀ Humidity: 10 to 90% no dew
Electric requirements:
ꢀ Voltage: 9V DC 500mA
ꢀ Power adapter: AC to DC Input 230VAC Output 9VDC, Current 500mA
ꢀ Network interface:1 RJ-45 Ethernet Connector
ꢀ FXS:1 FXS Connector
Size
152 x 115 x 32 mm (L x W x H)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Installation:
1
Connect handset to base: insert handset cord into handset cord jack at the
left side of the base.
2
Connect Gateway to Internet: plug the RJ-45 Ethernet cable into the
Ethernet Jack. Plug the other end of the cable into HUB.
3
Power on Gateway: plug the power cord adapter into the Power Jack.
Then plug the other end of the power cord adapter into the appropriate
wall outlet.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Configuration
To configure GW-200, you can use web browser and Telnet commands.
Configure by Web browser
After you’ve got the local IP address of the gateway from the voice prompt, On a PC
connecting with the gateway or at the same segment of the gateway, double click
icon to open the IE browser. Input the IP address of the gateway into address
bar (
), and then input password of the gateway into the
following page. Default password 1234 is ordinary password. Then
click button. The following configured page will popup. Input the data by
your computer’s keyboard according to your LAN parameters under the “network
settings”, “protocol settings”, “phone settings” and “audio settings”. When finished,
click “update” and quit the screen.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Network Setting
ꢀ iptype: Set how gateway gets relevant network parameters by selecting
corresponding item from drop down list.
¢
static ip: Select this item to authorize users set IP address, subnet
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
mask and router IP address of gateway manually.
¢
dhcp: Select this item to enable DHCP mode. With this system, your
LAN or router automatically assigns all the required network parameters
to any device connected to it when the device log on. GW-200 Gateway
is shipped from the factory with DHCP on. So, if you’re LAN or router is
configured to use DHCP addressing, the gateway’s LAN parameters will
automatically be configured as soon as it is connected to the LAN or
router and powered up.
¢
pppoe Those ADSL and Cable Modem users please select this item for
it is a protocol especially designed for them. With this system, ADSL ISP
automatically assigns all the required IP parameters to any device
connected to it when the device log on.
¢
modem If the gateway used with modem, please select this item to get
relevant network parameters auto. Then please fill ID and pin into ppp id
and ppppin fields.
ꢀ ppp id: With pppoe or modem selected in iptype drop down list, please
enter the user name here.
ꢀ ppp pin: With pppoe or modem selected in iptype drop down list,
please enter the password here.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ꢀ local ip: With static ip selected in iptype drop down list, please enter IP
address of gateway here.
ꢀ subnet mask: With static ip selected in iptype drop down list, please
enter subnet mask of Gateway here.
ꢀ
ꢀ
ꢀ
ꢀ
router ip: With static ip selected in iptype drop down list, please enter
router IP address of Gateway here.
dns: With static ip selected in iptype drop down list, please enter IP
address of DNS server here.
dns 2: With static ip selected in iptype drop down list, please enter IP
address of backup DNS server here.
mac: MAC address is the physical address supplied by the Ethernet
NIC. GW-200 gateway is shipped from the factory with a unique
algorism MAC address printed on the back of the base.
Protocol Setting
Fig 3.3 Protocol Setting
ꢀ use service: Enable/disable service by checking/clearing this box.
To make calls through gatekeeper, please check this box; otherwise,
gateway can only make IP-to IP calls.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ꢀ register ttl : The gateway will send a keep-alive registration message
to gatekeeper every “register ttl” seconds. The value range is
10-65535. Default is 60.
ꢀ jitter size : Set buffer size of RTP package. The value range is 0-32.
ꢀ service type: This option is used to accommodate the miscellaneous
requirements of the system providers. When gateway is connected to
these systems, please select the corresponding service type.
© Common: no special requirements
© Mediaring: use Mediaring prepaid card
© Etalk: use etalk prepaid card. When this is selected, please select
“dialnum” from the “Use dialplan” list box and put “00” into “dial
number”.
© Auvtech: use Auvtech’s
system. When connected with
Auvtech’s system, please select “auvtech” from the “nat traversal
” list box, select “account” from the “local type” list box.
© Subcentrex: Use Subcentrex’s system
© Ringtec: Use Ringtec’s system. When this is selected, please
select “dialnum” from the “Use dialplan” list box and put Ringtec
account into “dial number”.
© Smartcon: Use Smartcon’s system
© Dda: Use Dda’s system
© Vida: Use Vida’s system
© Citron: Use Citron’s system
© Asiasoft: Use Asiasoft’s system
© Huawei: Use Huawei’s system
© Asiainfo: Use Asiainfo’s system
© Lucent: Use Lucent’s system
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
© IPN: Use IPN’s system
© Yiyang: Use Yiyang’s system
© Thinker: Use Thinker’s system
© Suntek: Use Suntek’s system
ꢀ service addr, service id: Please put the URI (domain name/IP address)
of the server into “service addr”.
If “use service” is checked, please put the URI of gatekeeper into
“service addr” .The default service port is 1719. If the gatekeeper has a
GKID, please put it into “service id”.
If “use service” is not checked, to make calls through gateway, please put
the URI of the gateway into “service addr”. To make IP-to-IP call, please
clear this field. In both cases, the default service port is 1720.
ꢀ nat traversal: When the gateway with private IP address need
communicate with other IP phones in a different LAN or on Internet,
please select an item from dropdown list to set the proxy used by the
gateway.
¢
disable: Select this item when the log in server and gateway in the
same LAN, or the log in system supports the gateway working behind
the LAN.
¢
enable: When the system does not support gaeway working behind
the LAN, please select this item to search public IP address of the
NAT device. With this item selected, “nat addr” field will be activated.
Besides, port mapping (port forwarding) needs to be properly set up
on NAT device.
¢
citron: With Citron private protocol used, select this item to fit into the
GnuGK system transferring the voice and signal by router.
¢
¢
¢
auvtech: Select this item with Auvtech private system used.
vida: Select this item with Vida private system used.
aivgr: Select this item with aivgr private system used.
ꢀ nat addr: When “nat traversal” is set to “enable”, please put the
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
domain name of the servers ( These web server helps to find out the
public IP of the IP phone) into “nat addr”, such as
ꢀ nat ttl: When gateway sit behind a NAT device, it will send packets to
server every “nat ttl” seconds to keep the port mapping on the NAT
device alive. “nat ttl” is an integer between 10 and 65535 .default value
is 20.
ꢀ phone number: The local phone number or username of this phone,
usually is allocated by system.
ꢀ account: While calling card is set, please type the account of chosen
card into this field; while md5 account item selected in local type
dropdown list, enter ID here; while account is selected in local type
dropdown list, enter ID here. While prefix item selected in use
dialplan dropdown list, enter language indicating number, card number
and # here, such as 14589653185 .
ꢀ pin: While calling card is set, please type the password of chosen card
into this field; while md5 account item selected in local type dropdown
list, enter password here. While prefix item selected in use dialplan
dropdown list, enter password and # here, such as 3185.
ꢀ register port: The local UDP port registered with server to accept
incoming handshaking messages. any number between 1024 and
65535 is acceptable.
ꢀ signal port: This port is Q.931 port using TCP protocol, can be any
number between 1024 and 65535.
ꢀ control port: This port is H.245 port using TCP protocol, can be any
number between 1024 and 65535.
ꢀ dtmf: Set DTMF signal sending way by selecting control string,
inband audio, signal keypad or rfc 2833 from list box.
ꢀ dtmf payload : When DTMF select rfc 2833.This parameter can be
used indicating type of RTP payload type. The value can be use integer
96-101.
ꢀ rtp port: RTP port is the port transferring and receiving voice packets
using UDP protocol. This is an even number between 1024 and 65535,
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
can’t be the same as “register port”.
ꢀ local type: This parameter refers to how gateway authenticate itself to
the gatekeeper. The meaning of each item is as follow:
¢
¢
¢
phone number: Use phone number as E.164 and ID to login the
GK.
account: Use phone number as E.164 and designated ID filled in
account field as ID to login GK.
auto: Use support automated negotiate authentication account and
pin about MD5 or CAT .
¢
¢
¢
md5: Use MD5 authentication account and pin.
cat: Use CAT authentication account and pin.
sha1: Use SHA1 authentication account and pin.
ꢀ
call type: Set call type by selecting the items in drop down list.
¢
¢
normal: Call out in normal way by selecting this item.
advanced: Call out in faststart and tunneling way by selecting this
item. It is a recommended way with protocol used.
ꢀ rtp tos: Set the TOS field of the IP header of the RTP packets. The bigger
this value is 0, the higher priority the packet is .
phonesettings:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Fig 3.4 Phone Setting
ꢀ use dialplan: Set whether use dial plan or use dial number by selecting
the corresponding item in drop down list.
¢
¢
¢
disable: Do not use dial plan or dial number by selecting this item.
enable: Use dial plan by selecting this item.
dialnum: Use dial number by selecting this item. With this item
selected, please enter the dial prefix into dial number field.
prefix: Use 179XX service by selecting this item.
¢
¢
Hotline: Use Hotline function by selecting this item. With this item
selected, please enter the hotline number into dial number field.
Note With 179xx service used, please set as follows: fill call prefix into dial
number field, such as 17930; type; language indicating number, card
number and # into account field; fill password and # into pin field.
ꢀ
ꢀ
dial number: With dialnum selected in use dialplan drop down list,
please enter the dial prefix into this field according to requirement of log
in server. For example, with eTalk card used, enter 00 here.
ddd code: With enable or dialnum selected in use dialplan drop
down list, set area code according to E.164 dial rule. For example,
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Beiing 10; Shanghai 21.
ꢀ
ꢀ
ꢀ
idd code: With enable or dialnum selected in use dialplan drop down
list, set country code according to E.164 dial rule. For example, China
86; U.S.A .1.
idd prefix: With enable or dialnum selected in use dialplan drop
down list, set international call prefix according to E.164 dial rule, such
as 00.
ddd prefix: With enable or dialnum selected in use dialplan drop
down list, set long distance call prefix according to E.164 dial rule, such
as 0.
Note With dialnum seletcted in use dialplan drop down list, you can also
set dddcode, iddcode, iddprefix and dddprefix according to
requirement of system.
ꢀ
innerline: Enable/disable innerline call by selecting corresponding
items from dropdown list.
¢
¢
disable: Disable call innerline by selecting this item.
enable: enable call innerline by selecting this item.
ꢀ innerlineprefix: With enable selected in innerline dropdown list, please
fill the number prefix to pick up innerline , such as 0.
ꢀ Dual mode : This setting no need to set at moment.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ꢀ Dualmode prefix: This setting no need to set at moment.
¢
ring type: This setting no need to set at moment.
ꢀ Use digitmap: Enable/disable digit map by checking/unchecking the
box.
ꢀ Call waiting: Enable/disable call waiting by checking/unchecking the
box.
ꢀ forward number: Enter receiving forwarded calls phone number into
this field.
ꢀ fwd poweroff: Forward calls if power off by checking this box. Please
enter receiving forwarded calls phone number into fwd number field.
ꢀ fwd noanswer: Forward calls without replying by checking this box.
Please enter receiving forwarded calls phone number into fwd number
field.
ꢀ fwd always: Forward all calls by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
ꢀ fwd busy: Forward calls if busy by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
ꢀ answer: Enter a number from 0 through 60 to set the entries of the
seconds before the phone answer the call auto or forward the calls.
Audio settings:
Fig 3.5 Audio Setting
17
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ꢀ vad: Enable/disable VAD (voice activity detection).
ꢀ agc: Check for enable the Auto Gain Coctrol.
ꢀ aec: Check for enable Auto Echo Cancellation.
ꢀ codec1: Set the priority 1of the audio compression algorithm. The
options are g729 g7231 g711u g711a and gsm.
ꢀ codec2: Set the priority of the audio compression algorithm. The
options are g729 g7231 g711u g711a and gsm.
ꢀ codec3: Set the priority 3of the audio compression algorithm. The
options are g729 g7231 g711u g711a and gsm.
ꢀ codec4: Set the priority 4of the audio compression algorithm. The
options are g729 g7231 g711u g711a and gsm.
ꢀ codec5: Set the priority 5of the audio compression algorithm. The
options are g729 g7231 g711u g711a and gsm.
ꢀ g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate
is 6.3kbps, low rate is 5.3kbps.
ꢀ audio frame: Set audio frames in RTP package. Minimum is 1 and
maximum is 8.
ꢀ handset in: Drag the slider to adjust the volume of handset input. Drag
it to the left to reduce the volume; while drag it to the right to increase
the volume.
ꢀ handset out: Drag the slider to adjust the volume of handset output.
ꢀ speaker out: This setting no needed to set at this moment.
Other settings:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Fig 3.6 Other Setting
ꢀpassword: Set the password of the phone. (Default password is 1234).
ꢀsuper password: Set the super password of the phone.(Default super
password is 12345678).
ꢀdebug: Set the debug level of the phone.
¢
¢
disable: Disable output the debug message by selecting this item.
output: Output the operation information to the window, such as
register, input by selecting this item.
¢
¢
¢
output all: Output all debug information and data in test window by
selecting this item.
remote debug: Save the debug information in SDRAM of IP phone by
selecting this item.
no check: Disable checking firmware tags when upgrading. This is not
suggested, because it will increase the risk of upgrading the wrong
firmware into the phone.
ꢀ upgrade addr: Put IP address or domain name obtained by ISP of FTP
server supplying upgrade program into this field.
ꢀ nts ip: No needed to set for the Gateway(GW-200).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ꢀ use daylight: No needed to set for the Gateway(GW-200).
ꢀ timezone: No needed to set for the Gateway(GW-200).
When debug set as 0[disable], if input ordinary password (default one is 1234),
then following page will pop up after clicking
parameters can be modified.
. And only those
Fig 3.7 Setting Page using ordinary pin with Debug set as 0 [disable]
ꢀ Update: Click this button to save the configuration and the phone will
reboot. Once the phone reboots successfully, the new configuration is
effective.
Note After entering set page, if Update button is not clicked within 5
seconds, then when you click it again, the index page asking for pin
will pop up again. Then please input the password again to enter
the set page and then click Update button to confirm the
modification.
Phone Book: Click this button to open the speed dial settings page. Please
refer to Fig 3.7. In this page, you can set and save the speed dial number by
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
typing the name into the Name field and then entering the corresponding
number following the name. For example, input Jack in Name field following
001, and then input 5989426454 into Phone number field. Then Jack’s number
5989426454 is saved in phone book. Then please click Save/Back button. In
normal state, you can use speed dial to call numbers saved in phone book.
Fig 3.8 Phone Book Illustration
Upgrade Program: Click this button to update the program of gateway. Before
updating, please fill IP address of FTP server into upgrade addr field, and
then click this button. Then the gateway will read the corresponding bin files
from the server and then load into the gateway.
Update Digitmap: Click this button to update the digitmap of the gateway.
Before updating, please fill IP address of FTP server into upgrade addr field,
and then click this button. Then the gateway will read the corresponding map
files from the server and then load into the gateway.
‹ Telnet Configuration
ꢀ On the PC choose Start>Run, and then type telnet 192.168.1.100 into
Run field in popuping Run dialog. Or input telnet 192.168.1.100 in the
DOS window. Then the following information will be displayed.
GW-200 V1.40 settings
Password :
Then please type password. With debug is set as 0[disable], if type ordinary
password (default one is 1234), after Retun, you will see
Password : ****
21
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
P:\>
If you type super password, then you will see:
Password : ********
P:\>
Above information indicates that gateway is under setting mode, and then you
can set the GW-200 gateway by using the telnet commands.
‹ GW-200 Gateway Telnet Commands Explanation
GW-200 gateway Telnet Commands
Command
?
Function
Supply command name and parameters
get
set
Display basic parameters of the GW-200 gateway
Set parameters of the GW-200 gateway
store
load
exit
write
ping
ftp
Save current settings to designated position
Load designated settings to current position
Exit from the setting mode without saving the configuration
Exit with saving all configurations and restart GW-200 gateway
Ping other net parameter
The gateway connects to FTP server and then get the files
Detail description of GW-200 Telnet commands
Command ?
Syntax description: No optional parameter
Usage: Type command name and parameters following P:\> . Be used
as the keyword to supply keyword and parameters of the relevant
commands.
Relevant usage: None
22
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Detailed description:
List help of all commands
For example:
P:\>?
set
get
list settings
store x
load x
exit
store current to xth settings
load xth settings to current
write
save settings
Command get
Syntax description: No optional parameter of keywords
Usage: Display basic parameters of the GW200 gateway
Relevant usage: None
Detailed description:
get
Display basic running parameters of the GW-200 geatway.
Input ordinary password without debug being set as 0[disable], or input
super password with debug set as 0[disable], then following parameters
of gatway will be displayed:
GW-200 V1.40 .014 settings
Password: ********
P:\>get
iptype 0[static]
ip 192.168.1.100
192.168.1.254
dns 202.106.196.152
00-09-45-65-a3-e6
service 1[enable]
subnetmask 255.255.255.0
dns2 202.106.196.115
router
mac
servicetype 0[common] serviceaddr 203.93.9.57
serviceid
23
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
[empty]
nattraversal 1[enable]
phonenumber 182378009 account [empty]
pin [empty]
controlport
registerport 6800
6802
signalport 6800
rtptos 0
registerttl 60
rtpport 6802
jitter size 0
calltype 1[advanced]
0[control string]
dtmfpayload 101
dialplan 2[dialnum]
[empty]
iddcode [empty]
[empty]
innerline 1[enable]
0[disable]
localtype 0[phonenumber]
dtmf
dialnumber 17911
iddprefix [empty]
dddcode
dddprefix
digitmap
innerlineprefix [empty]
dualmode 0[disable]
answer 5
callwaiting 0[disable]
ringtype 0[dtmf0]
fwdnumber [empty]
fwdalways 0[disable]
0[disable]
audiotype 0[g7231]
1[enable]
fwdpoweroff 1[enable]
fwdbusy 0[disable]
audioframes 1
agc 0[disable]
fwdnoanswer
6.3k
vad 1[enable]
1[enable]
aec
handsetin
9
handsetout 21
codec3
speakerout 21
codec1 1[g7231]
2[g711u]
codec4 4[gsm]
password 1234
debug 1[output]
upgradeaddr [empty]
sntpip 0.0.0.0
codec2 0[g729]
codec5 5[null]
superpassword 19750407
daylight 0[disable]
timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]
Input ordinary password with debug set as 0[disable], following information will
be seen:
GW-200 V1.40 settings
24
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Password:****
P:\>get
iptype 0[static]
ip 192.168.1.100
192.168.1.254
dns 202.106.196.152
subnetmask 255.255.255.0
dns2 202.106.196.115
router
nattraversal 1[enable] nataddr
rtpport 5144
registerport 5142
account [empty]
signalport 5142
pin [empty]
controlport 5144
phonenumber 182378009 fwdpoweroff 0[disable]
fwdalways 0[disable]
0[disable]
ringtype 0[dtmf0]
password 1234
upgradeaddr [empty]
sntpip 0.0.0.0
fwdbusy 0[disable]
answer 5
fwdnoanswer
daylight 0[disable]
timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]
Command set
Syntax description: set keywords value
Usage: Used to configure password and other running parameters of
GW-200 gateway.
Detailed description:
set iptype X
Set how gateway gets relevant network parameters. X ranged
from 0 through 3: 0: authorize users set IP address, subnet mask
and router IP address of gateway manually; 1: use DHCP mode.
With this system, your LAN or router automatically assigns all the
required network parameters to any device connected to it when
the device log on. GW-200 gateway is shipped from the factory
with DHCP on. So, if your LAN or router is configured to use
25
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
DHCP addressing, the gateway’s LAN parameters will
automatically be configured as soon as it is connected to the LAN
or router and powered up; 2: use PPPoE mode. Those ADSL and
Cable Modem users please select this item for it is a protocol
especially designed for them. With this system, ADSL ISP
automatically assigns all the required IP parameters to any device
connected to it when the device log on; 3: use modem mode.
Those who use gateway with modem, please set the value as 3.
set pppid XXX
With iptype set as 2, use this command to set ADSL ID; with
iptype set as 3, use this command to set Modem ID.
set ppppin XXX
With iptype set as 2, use this command to set ADSL pin; with
iptype set as 3, use this command to set Modem pin.
set ip XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP address of
gateway .
set subnetmask XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set subnet mask of
gateway.
set router XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set router IP of network
26
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
with gateway.
set dns XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP address of DNS
server.
set dns2 XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP of backup DNS
server.
set mac XX-XX-XX-XX-XX-XX
Set MAC address of the GW-200 gateway. Parameter
xx-xx-xx-xx-xx-xx must be an HEX number.
set service X
Set register the gatekeeper or not. X ranged from 0 through 1. 0:
do not register; 1: register.
set service type X
Enable/disable the repaid and service system .choose the repaid
server provider. Parameter x ranged from 0 through 29:
0: common: disable repaid card; 4: use Mediaring service; 2: use
eTalk card; 3: use Auvtech system; 5: use Ringtec service; 6: use
Smartcon service; 7: use dda service; 8: use vida service; 9: use
citron system; 10: use asiasoft system; 12: use zte system; 13:
use huawei system; 16: use asiainfo system; 17: use Lucent
system; 19: use IPN system; 20: use yayuang system; 21: use
27
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
thinker system; 22: use suntek system; 28: use txtc system.
set serviceaddr XXXX
Set IP address or domain name of gatekeeper.
set serviceid XXXXX
Set service ID according to required by service system.
set nattraversal X
Set NAT traversal or not. X ranged from 0 through 7: 0: do not use.
When the log in server and gateway in the same LAN, or the log in
system supports the gateway working behind the LAN; 1: Use
NAT traversal. When the login system does not support gateway
working behind the LAN, please use this value to search public IP
address of the NAT device. With this item selected, please make
port mapping on NAT device; 2: With Citron private protocol used,
use this value to fit into the GnuGK system transferring the voice
and signal by router; 3: use this value with Innopath private system
used; 5: use this value with vida private system used; 6: aivgr use
this value with aivgr private system used; 7: use this value with
Eproxy private system used.
set nataddr XXXXX
Set IP address of NAT device wan port or URI of free assistant
28
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
ip.sbbs.net;
set natttl XX
Set NAT TTL XX is an integer between 10 and 65535 sec. default
value is 20 sec.
set phonenumber XXXXXXXX
Set a phone number of GW-200 gateway. Value xxxxx must be an
Arabic numeral and no longer than 16 characters.
set account XXXXXX
While calling card is set, set account of chosen card; while local
type is set use authentication type, set user ID; while set
localtype is set as 1, set ID.
set pin XXXXXXXXXX
While calling card is set, set password of chosen card; while local
type is set authentication type, set password.
set registerport XXXX
Set register port. XXXX is range from 1024 through 6553.
set signalport XXXX
This port is Q.931 port using TCP protocol. XXXX is range from
1024 through 65535.
set controlport XXXX
29
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
This port is H.245 port using TCP protocol. XXXX is range from
1024 through 65535.
set registerttl X
Set register TTL. X is range from 10 through 65535 Sec. default
value is 60 Sec.
set rtptos X
Set TOS segment of IP head package in RTP digital follow.
set rtpport XXXX
RTP port is the port transferring and receiving voice flow using
UDP protocol. XXXX is range from 1024 through 65535.
set jittersize X
Set buffer size of RTP package. X is range from 0-32.
set calltype X
Set call type of the phone. X is ranged from 0 through 2: 0: call out
in normal way; 1: call out in faststart and tunneling way. It is a
recommended way.
set localtype X
This command used to set how gateway log in gatekeeper. X is
ranged from 0 through 6: 0: use phone number as E.164 and ID
to login the GK; 1: use phone number as E.164 and designated
ID by set account XXX command; 2:use support automated
negotiate about MD5 or CAT authentication system.3:use MD5
authentication account and pin;4: use CAT authentication account
30
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
and pin; 5: use SHA1 authentication account and pin.
set dtmf X
Set DTMF relay type. X is ranged form 0 through 3: 0:control
string 1:inband audio 2: signal keypad 3:rfc 2833.
set dtmf payload X
When dtmf X select 3(rfc 2833).This parameter can be used
indicating type of RTP payload type. The value can be use integer
96-101.
set dialplan X
Enable/disable dial plan and dial number. Parameter X ranged
from 0 through 4: 0: disable dial plan; 1: enable dial plan; 2: use
dial number; 3: use 179XX service; 4: use hotline function.
set dialnumber XX
When set dialplan value set as 2, please use this command to set
dial number. For example, with eTalk card used, please set it as
00. When set dialplan value set as 4, please use this command to
set hotline number.
set dddcode XX
Set the area code when set dialplan value set as 1 or 2. For
example, the area code of Beijing is 10; the area code of Shanghai
is 21, and the area code of Chengdu is 28, etc. Parameter xxx
must be an Arabic numeral and no longer than 3 characters.
set iddcode XXX
31
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Set the country code when set dialplan value set as 1 or 2. For
example, the country code of China is 86; the country code of USA
is 1, etc. Parameter xxxx must be an Arabic numeral and no longer
than 4 characters.
set iddprefix XX
Set IDD service prefix number when set dialplan value set as 1 or
2. For example, IDD service prefix number of china is 00; IDD
service prefix number of USA is 1, etc. Parameter xxx must be an
Arabic numeral and no longer than 3 characters.
set dddprefix XX
Set DDD service prefix number when set dialplan value set as 1
or 2. For example, DDD service prefix number of china is 0; DDD
service prefix number of USA is 1, etc. Parameter xxx must be an
Arabic numeral and no longer than 3 characters.
set innerline X
Set use innerline call or not. X ranged from 0 through 1: 0: disable;
1: enable innerline call.
set innerlinepreifx X
With innerline set as 1[enable] , please set the prefix to pick up
inner line, such as 0.
set answer X
Set the ring seconds before the phone answers the call auto or
forward the calls. X is ranged from 0 through 60.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
set ringtype X
This setting no need to set at moment.
set digitmap X
Set whether to use digitmap. X ranged from 0 to 1: 0: do not use
digitmap; 1: use digitmap.
set fwdnumber XXXXXXX
Set receiving forwarded calls phone number. XXXX must be an
Arabic numeral and no longer than 16 characters
set fwdpoweroff X
Enable/disable forward calls if power off. X is ranged from 0
through 1. 0: do not forward calls if power off; 1: forward call if
power off.
set fwdalways X
Enable/disable forward all calls. X is ranged from 0 through 1. 0:
do not forward all calls; 1: forward all calls.
set fwdbusy X
Enable/disable forward calls if busy. X is ranged from 0 through 1.
0: do not forward calls if busy; 1: forward call if busy.
set fwdnoanswer X
Enable/disable forward calls without replying. X is ranged from 0
through 1. 0: do not forward calls without replying; 1: forward call
33
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
without replying.
set audioframes X
Set audio frames in RTP package. X is Arabic numerals between 0
and 7.
set 6.3k X
With G.7231, set PA168X IP phone to use 6.3K rate or not. X is
ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate.
set vad X
Enable/disable VAD. X is ranged from 0 through 1: 0: disable VAD;
1: enable VAD.
set agc X
Enable/disable AGC. X is ranged from 0 through 1: 0: disable AGC;
1: enable AGC.
set aec X
Enable/disable AEC. X is ranged from 0 through 1: 0: disable AEC;
1: disable AEC.
set handsetin X
Set initial volume of handset. X is ranged from 0 through 15.
set speakerin X
Set initial volume of microphone of the base. X is ranged from 0
through 15.
set handsetout X
34
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Set initial volume of handout. X is ranged from 0 through 31.
set codec1 X
Set the priority 1of the audio compression algorithm. X is range
from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec2 X
Set the priority 2 of the audio compression algorithm. X is range
from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec3 X
Set the priority 3 of the audio compression algorithm. X is range
from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec4 X
Set the priority 4of the audio compression algorithm. X is range
from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec5 X
Set the priority 5 of the audio compression algorithm. X is range
from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set password XXXX
Set password of the GW-200 Gateway. XXX must be ASCII
characters.
set superpassword XXXX
Set super password of the GW-200 Gateway . XXX must be ASCII
characters.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
set debug X
Set open debugging message output grade for special tool. X is
ranged from 0 through 5: 0: close debugging output; 1: output the
operation information to the window; 2: output all the bug
information and data in test window; 3: save the bug information
into SDRAM; 4: disable checks the mark.
set upgradeaddr XXX.XXX.XXX.XXX
Set IP address or domain name of FTP server supplying upgraded
program of GW-200.
set nt XXX.XXX.XXX.XXX
No needed to set for the Gateway(GW-200).
set daylight X
No needed to set for the Gateway(GW-200).
set timezone XX
No needed to set for the Gateway(GW-200).
Command store
Syntax description: no keyword. Parameter ranged from 0 through 4.
Usage: Save the current settings to the designated position.
Relevant Usage: store 1
Command load
Syntax description: no keyword. Parameter ranged from 0 through 4.
Usage: Load the designated settings to the current position.
Relevant Usage: load 1
Command exit
36
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
Syntax description: no keyword and parameter
Usage: Exit from Telnet command window without saving the
configuration.
Relevant usage: None
Command write
Syntax description: No keyword and parameter
Usage: Save the configuration and restart the GW-200 gateway.
Command ping
Syntax description: ping IP address
Usage: ping IP address of other NAT device
Relevant usage: In telnet window, input ping xx.xxx.xx.xx an IP
address
and return, then the result will be displayed. If the address is
effective, ping OK will be seen; if the address is ineffective, nothing
will be seen. Fox example:
P:\>ping 203.93.9.57
P:\>
ping OK
P:\>ping 27.56.120.56
P:\>
Note Usually, the echo time of ping command is no more than 1 second. So
if the
result is not displayed in 5 seconds, ping command is fail.
ftp command
Syntax description: ftp value
Usage: the system connects to the FTP server auto to get the
corresponding file and deal with it.
Relevant usage: ftp X
X ranged from 0 through 2:
37
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
X-0: Connect to FTP Server to get the file of updating program and
save it to the SDRAM of the gateway. Then the file can be read by
PalmTool. This operation aims at testing.
X-1: Connect to FTP Server to get the file of updating program and
update program Flash. This operation aims at updating program.
X-2: Connect to FTP Server to get the file of updating dial rules and
update program Flash. This operation aims at updating dial rule.
Note When you use ftp 0 and ftp 1 commands, if the file get from FTP server
is too large or the net speed is too slow, then the process will not be
seen in telnet window. Please be patient. Using ftp command in telnet
to get file spends almost same minutes as getting file using gateway.
So if nothing is displayed after too long time, it means that ftp is fail.
Note All the Telnet commands of GW-200 gateway should be written in low
case and the password is case sensitive.
‹ Usage of the phone
‹ Receiving calls:
GW-200 gateway can receive incoming calls from other IP Phone or
another IP Gateway which and support the protocol. It works just like an
ordinary phone. When it rings, pick up the handset to answer the incoming
calls and finish, put the handset back.
‹ Place a call
ꢀ Call another IP Gateway or IP phone under the same Gatekeeper:
Pick up the handset and listen for the Internet dial tone. Then dial the
phone number you wish to call and press [#] to end the dialing. Once the
call connection has been established and the ring tone has sounded, wait
38
Download from Www.Somanuals.com. All Manuals Search And Download.
GW-200 User Manual
for the other party to answer. When the other party answers, you can begin
speaking. When the call is finish, put back the handset.
ꢀ Place a call with Fix IP Address
If GW-200 Gateway which with the Fix IP address and without used the
Gatekeeper service, you can place a call to which also with Fix IP and
without used the Gatekeeper service. Pick up the handset and then
entering the IP address with the number key, pressing the [*] key as a
“.”(dot) and press the [#] key end the dialing. Wait for the other party
answer. When the call is finish, put back the handset.
ò
Dial out the number from phone book
Pick up the handset and listen for the dialing tone. Pressing the [#] and
then press the Phone Book memory number (2 digits). Then pressing the
[#] key to end the dialing. The Gateway will automatically dial out the
number which stored before.
Perfectone Website at: www.perfectone.net
Copyright @ 2005 Perfectone Net Ware Company Limited. All right reserved
39
Download from Www.Somanuals.com. All Manuals Search And Download.
|