Operating instructions
for heat pump dryers
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-GB
M.-Nr. 09 696 880
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Caring for the environment .................................................................................. 2
Warning and Safety instructions ......................................................................... 6
Operating the tumble dryer................................................................................. 16
Before using for the first time............................................................................. 19
EcoFeedback........................................................................................................ 20
1. Notes on correct laundry care........................................................................ 21
Garment care label symbols............................................................................. 22
2. Load the tumble dryer ..................................................................................... 23
3. Select a programme and start it..................................................................... 24
4. Remove the laundry......................................................................................... 27
Remove the laundry............................................................................................... 27
Options.................................................................................................................. 28
Delay start............................................................................................................. 30
Programme chart................................................................................................. 31
Changing the programme sequence ................................................................. 37
Cleaning and care................................................................................................ 38
Emptying the condensed water container............................................................. 38
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Removing the plinth filter.................................................................................. 42
Cleaning the plinth filter.................................................................................... 42
Checking the condenser unit............................................................................ 43
Fragrance flacon .................................................................................................. 46
Problem solving guide......................................................................................... 50
Other problems...................................................................................................... 53
Steam smoothing spray jet ................................................................................... 57
After sales service ............................................................................................... 58
Repairs................................................................................................................... 58
Installation and connection................................................................................. 59
Consumption data ............................................................................................... 68
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Technical data ..................................................................................................... 69
Settings menu ...................................................................................................... 70
Language ............................................................................................................ 70
Extended cool down.............................................................................................. 71
Buzzer volume ...................................................................................................... 72
Conductivity........................................................................................................... 72
Total consumption ................................................................................................. 72
Display brightness ................................................................................................ 73
Memory.................................................................................................................. 74
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
It is essential to read these instructions.
This tumble dryer complies with current safety requirements. Inap‐
propriate use can, however, lead to personal injury and damage to
property.
To avoid the risk of accidents and damage to the tumble dryer,
please read these instructions carefully before using it for the first
time. They contain important information on its safety, installation,
use and maintenance.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
This tumble dryer is intended for use in domestic households and
similar working and residential environments.
This tumble dryer is not intended for outdoor use.
It must be used only as a domestic appliance to dry items which
have been washed in a water solution and which are marked on the
manufacturer's care label as being suitable for tumble drying. If us‐
ing dry cleaning kits, do so at your own risk, and follow the instruc‐
tions provided on the packaging.
Any other applications may be dangerous. Miele cannot be held lia‐
ble for damage resulting from incorrect or improper use or operation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This tumble dryer can only be used by people with reduced physi‐
cal, sensory or mental capabilities, or lack of experience or knowl‐
edge, if they are supervised whilst using it or have been shown how
to use it in a safe way and understand and recognise the conse‐
quences of incorrect operation.
Safety with children
Children under 8 years of age must be kept away from the tumble
dryer unless they are constantly supervised.
Children 8 years and older may only use the tumble dryer unsu‐
pervised if they have been shown how to use it safely and recognise
and understand the consequences of incorrect operation.
Children must not be allowed to clean or maintain the tumble dry‐
er unsupervised.
Please supervise children in the vicinity of the tumble dryer and
do not let them play with it.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Before setting up the tumble dryer, check it for any externally visi‐
ble damage.
Do not install or use a damaged tumble dryer.
Before connecting the tumble dryer, ensure that the connection
data on the data plate (fuse rating, voltage and frequency) match the
mains electricity supply. If in any doubt, consult a qualified electri‐
cian.
The electrical safety of this tumble dryer can only be guaranteed
when correctly earthed. It is essential that this standard safety re‐
quirement is met. If in any doubt, please have the household wiring
system tested by a qualified electrician. Miele cannot be held liable
for the consequences of an inadequate earthing system (e.g. electric
shock).
Do not connect the appliance to the mains electricity supply by an
extension lead, multi-socket adapter or similar. These can overheat
and are a fire hazard.
If the electrical connection cable is faulty it must only be replaced
by a Miele authorised service technician to protect the user from
danger.
Unauthorised repairs could result in unforeseen dangers for the
user, for which Miele cannot accept liability. Repairs should only be
undertaken by a Miele approved service technician, otherwise any
subsequent damage will not be covered by the guarantee.
Faulty components must only be replaced by genuine Miele origi‐
nal spare parts. The manufacturer can only guarantee the safety of
the appliance when Miele replacement parts are used.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
The tumble dryer must be isolated from the electricity supply in
the event of a fault and during cleaning and maintenance.
This tumble dryer must not be used in a non-stationary location
(e.g. on a ship).
Do not make any alterations to the tumble dryer, unless author‐
ised to do so by Miele.
Heat pump technology and refrigerant:
The heat pump in this tumble dryer uses a refrigerant which is con‐
densed by the compressor and led in a closed circuit through the
heat exchanger unit where heat exchange with the circulating drying
air takes place.
– The humming noises caused by the heat pump are normal and do
not impair the efficient functioning of the dryer.
– The refrigerant is not flammable or explosive.
– In general it is not necessary to leave the dryer standing for any
length of time before it is connected to the mains provided it has
been transported and installed correctly (see "Installation and
connection").
If it has not been transported as described, ensure that the rec‐
ommended standing time prior to first operation is observed. Oth‐
erwise the heat pump can be damaged.
– This tumble dryer contains fluorinated greenhouse gases. They
are hermetically sealed.
Designation: R 134a
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Please observe the instructions in "Installation and connection"
and the "Technical data".
The accessibility of the plug must always be ensured, in order to
disconnect the tumble dryer from the mains.
Do not block the gap between the bottom of the tumble dryer and
the floor with plinth facings, deep pile carpet etc. This would hinder
a sufficient flow of air to the dryer.
Make sure the dryer door can be opened without hindrance after
installation.
Correct use
The maximum load for this tumble dryer is 8.0 kg (dry weight).
The maximum recommended loads for individual programmes are
given in the Programme chart.
To prevent the risk of fire, do not connect the tumble dryer via a
controllable socket (e.g. a timer or a peak-load switch-off device).
If the drying programme is interrupted before the end of the cooling
down phase, this could cause the laundry to self-ignite.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
To prevent the risk of fire, the following textiles must not be dried
in this tumble dryer:
– Items which have not been washed.
– Items, such as workwear, which have not been thoroughly
cleaned and which are still soiled with grease, oil or other depos‐
its (such as cosmetics, lotions etc). If items have not been thor‐
oughly cleaned there is a danger that these might ignite when
heated, even after they have been removed from the dryer at the
end of the programme.
– Items (e.g. mops and floor cloths) which have been treated with
inflammable cleaning agents or which contain residues of ace‐
tone, alcohol, benzene, petrol, kerosene, stain remover, turpen‐
tine, wax and wax remover or other chemicals.
– Items which have been splashed with hair lacquer, hair spray, nail
varnish remover or similar substances.
When washing such heavily soiled items ensure that you use suffi‐
cient detergent and select a high temperature. If in doubt, wash
the items several times.
Remove all items from pockets (e.g. lighters, matches).
Warning: Do not switch the dryer off before the drying pro‐
gramme has finished. If this is done, the laundry must be hung up or
spread out to cool it down.
Fabric conditioner and similar products must be used according
to the instructions on the manufacturer's packaging.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
To prevent the risk of fire, the following textiles must not be dried
in this tumble dryer:
– Items which have been cleaned using chemicals (e.g. professio‐
nal dry-cleaning agents).
– Items which contain a large proportion of rubber, foam rubber or
rubber-like materials. For example, products made from latex
foam rubber, shower caps, waterproof textiles, rubberised articles
and items of clothing and pillows with foam rubber filling.
– Damaged items which contain padding or fillings (e.g. pillows,
jackets). When damaged, the filling can get out with the risk of it
igniting in the dryer.
In many programmes, the heating phase is followed by a cooling
down phase to ensure that the items are not too hot to handle when
you remove them (this also avoids the danger of the laundry self-ig‐
niting). The programme is not finished until the cooling down phase
has been completed.
As soon as the programme has finished, remove all laundry from the
drum.
Do not let anyone sit or lean on the door, as this can cause the
tumble dryer to tip up.
Always close the door after use. This way you will avoid the dan‐
ger of:
– Children climbing onto or into the dryer or hiding things in it.
– Pets or other small animals climbing into it.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
The tumble dryer must not be used without fluff filters or
– with damaged fluff filters, or
– with a damaged plinth filter.
This would cause an excessive build-up of fluff which in turn would
cause a fault.
The fluff filters must be cleaned after every drying cycle.
The fluff filters and the plinth filter must be thoroughly dried after
cleaning. Do not replace them if they are damp or wet. Damp or wet
filters could cause operational faults.
Do not install the tumble dryer in a room where there is a risk of
frost occurring. At temperatures around freezing point the tumble
dryer may not be able to operate properly. There is a risk of damage
if the condensed water is allowed to freeze in the pump and hoses.
If the water is drained externally through the drain hose instead of
being collected in the condensed water container, make sure the
drain hose is securely attached if you hang it in a sink or basin to
avoid the hose slipping and the water causing damage.
Condensed water is not drinking water.
It can cause health problems in both people and animals if con‐
sumed.
Always keep the area around the tumble dryer free of dust and
fluff.
Dust drawn into the tumble dryer can cause blockages in the heat
exchanger over time.
The tumble dryer must not be hosed down.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Using a fragrance flacon (optional accessory)
Only use genuine Miele original fragrance flacons.
The fragrance flacon must be stored in its packaging so please
make sure you retain this.
Caution. The fragrance can leak out of the flacon. Make sure that
you always keep the flacon, or the fluff filter with the flacon inserted
in it, in a horizontal position when carrying and do not tip or place
down on any surface.
Use an absorbent cloth to wipe up any fragrance which has
leaked out of the flacon onto the floor, the dryer or any dryer compo‐
nents (e.g. the fluff filter) immediately.
If fragrance which has leaked out of a flacon: comes into contact
with the skin - wash the skin thoroughly with soap and water;
comes in contact with the eyes - rinse the eyes with clean water for
at least 15 minutes; is swallowed - rinse out the mouth thoroughly
with clean water. Seek medical advice in the case of contact with
the eyes or if fragrance has been swallowed.
If fragrance which has leaked out of a flacon comes in contact
with clothing, change the clothing immediately. Wash the clothing or
any cloths used for mopping up fragrance thoroughly with plenty of
water and detergent.
There is the risk of fire or damage to the tumble dryer if the follow‐
ing instructions are not observed:
– Never refill a flacon with fragrance.
– Never use a faulty fragrance flacon.
Dispose of an empty fragrance flacon with the household waste
and never use it for any other purpose.
Please also observe the information supplied with the fragrance
flacon.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Accessories
Only use genuine Miele original spare parts and accessories with
this appliance. If non-Miele parts are used, guarantee, performance
and product liability claims will be invalidated.
The tumble dryer can be combined with a Miele washing machine
in a washer-dryer stack. The appropriate "WTV" stacking kit (availa‐
ble to order) to match your tumble dryer and washing machine is re‐
quired.
If you order a plinth for this tumble dryer (available from Miele as
an optional accessory - depending on country), make sure it is the
correct one.
Miele cannot be held liable for damage caused by non-compli‐
ance with these Warning and Safety instructions.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the tumble dryer
Control panel
a
f
Display with sensors
Option buttons
See the following page for more in‐
formation.
Various options can be added to the
programmes.
b
g
h
i
Start/Stop button
Programme selector
For selecting the programme.
For starting the programme selected
and cancelling a programme once it
has started.
Optical interface
For service technicians.
c
Drying level button
For all programmes with a selectable
drying level.
button
For switching the tumble dryer on
and off. To save energy the tumble
dryer will switch off automatically 15
minutes after the end of the pro‐
gramme/anti-crease phase or after
switched on if no other selection is
made.
d
Duration button
For selecting the duration for timed
drying programmes.
e
Delay start button
For selecting delay start.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the tumble dryer
Settings can be changed to alter the
dryer's electronics to suit different re‐
quirements. Please refer to "Settings
menu" at the end of this booklet for
more information.
Display
The following programmes are selec‐
ted using the programme selector at
the "Further programmes" position:
– Automatic plus
– Delicates
– Proofing
– Sportswear
– Outerwear
– Cool air
, OK, sensors
These sensors are used to operate the
display when the symbols light up.
– Basket programme
– sensor
Scrolls down the list to the next op‐
tion or decreases a value.
– OK sensor
Confirms the programme selected, a
value set or opens a sub-menu.
– sensor
Scrolls up the list to the next option
or increases a value.
The sensor symbols will go out if no se‐
lection is made. They will also go out if
a selection is not confirmed with OK.
EcoFeedback sensor
See "EcoFeedback" for more informa‐
tion.
Settings
The Settings menu is opened by touch‐
ing the and sensors at the same
time.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the tumble dryer
Perfect Dry indicator
Examples on how to operate the ap‐
pliance
With programmes with a selectable dry‐
ing level, the Perfect Dry system calcu‐
lates the residual moisture present in
the laundry to ensure a precise drying
result.
Scrolling through a list
The arrows in the display indicate
that a selection is available:
The Perfect Dry indicator . . .
. . . will flash after the programme has
started and go out when the pro‐
gramme duration appears in the dis‐
play.
. . . will light up again when the selected
drying level is reached and remain on
until the end of the programme.
. . . will remain dark with the following
programmes: Woollens handcare, Silks
handcare, Cool air, Warm air, Basket
programme.
Automatic plus
Touching the sensor scrolls down the
list to the next option and touching the
sensor scrolls up the list to the next
option.
The OK sensor is used to confirm your
selection.
Identifying options selected
Normal
Estimated time remaining
If an option has been activated with
After the programme has started the
estimated programme duration will ap‐
pear in the display in hours and mi‐
nutes.
OK, it will be given a tick.
Setting numerical values
Duration
0:20
h
The programme duration displayed for
programmes with a selectable drying
level may vary or "jump". The following
factors, among others, affect the pro‐
gramme duration displayed: the quanti‐
ty of the laundry, the type of fabric and
the residual moisture in the laundry. The
electronics continually access condi‐
tions in the appliance and adjust the
programme duration with increasing ac‐
curacy.
A numerical value is highlighted in
white. Touching the sensor decrea‐
ses the value and touching the sen‐
sor increases it. The OK sensor is used
to activate the value.
Exiting a sub-menu
Select to exit a sub-menu.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
The arrows in the display indicate
that further options are available.
Removing the protective foil
and stickers
Remove
Confirm your choice of language by
touching the OK sensor.
– the protective foil from the door.
Completing the procedure for
using for the first time outlined
in these instructions
– any stickers from the front and the
lid.
Please do not remove any labels
(e.g. the data plate), visible when you
open the door.
See
Confirm by touching the OK sensor.
After installing the dryer
Read "1. Notes on correct laundry
care" and "2. Load the tumble dryer".
Before using the tumble dryer for
the first time, ensure that it is instal‐
led and connected to the electricity
supply correctly. If it has not been
transported as described in "Installa‐
tion and connection" then it must be
left to stand for at least 1 hour before
it is connected to the electricity sup‐
ply.
You can then load the dryer and se‐
lect a programme as described in "3.
Select a programme and start it".
The procedure for using for the first
time is completed when a programme
lasting longer than one hour has been
carried out in full.
When the tumble dryer is switched on
the welcome display Miele Willkommen
will appear briefly.
Setting the language
You will be asked to select the lan‐
guage you want for the display. It is
possible to change the language at any
time via Settings.
deutsch
You can scroll through the list by
touching the and sensors until
the language you want is highlighted
in the display.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EcoFeedback
You can use the EcoFeedback sensor
to call up information about the energy
consumption of your dryer.
2. Actual consumption
Touch the EcoFeedback sensor.
You can view the actual amount of en‐
ergy used.
Touching the EcoFeedback sensor will
call up two types of information:
Example:
– an estimate of the consumption be‐
fore the programme begins
Energy
2,0
kWh
– the energy consumption during the
< 0.1 kWh will be displayed if the ener‐
gy consumption is very low.
programme.
The EcoFeedback sensor will light up
and information will appear in the dis‐
play.
The consumption will vary depending
on the programme stage and residual
moisture present.
Both will go out automatically a few
seconds later or alternatively they can
be confirmed with OK.
If the door is opened or the tumble
dryer has switched off automatically
at the end of the programme, the da‐
ta will revert to the estimated con‐
sumption.
At the end of the programme, before
opening the door, you can also call up
the following in the display:
Total consumption setting
– the energy consumption and
– shows consumption data for the pro‐
gramme which has just been run
– the degree of soiling of the fluff filters
and the plinth filter (0 % = light, 50 %
= medium, 100 % = heavy). Accumu‐
lating fluff and soiling will cause the
programme duration to increase
which in turn will increase energy
consumption.
and
– shows total energy consumption to
date.
See "Settings menu" for more detailed
information.
1. Estimate
After selecting a programme, touch
the EcoFeedback sensor.
For a few seconds bars which indicate
the estimated consumption will appear:
Energy
The more bars visible, the higher the
energy consumption.
The estimate will vary depending on the
programme and any options selected.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Notes on correct laundry care
Points to note regarding wash‐
ed laundry
– When washing very heavily soiled
items ensure that you use sufficient
detergent and select a high tempera‐
ture. If in doubt, wash the items sev‐
eral times.
See "Warning and Safety" in‐
structions for further information.
Loading or using the tumble dryer in‐
correctly could cause a fire.
– Sort the laundry according to the
type of fibre and weave, size, gar‐
ment care label symbol and the dry‐
ing level required.
– Do not put soaking wet items into the
tumble dryer. Make sure your laundry
is thoroughly spun before drying. The
higher the spin speed, the greater the
savings that can be made in energy
and time during drying.
– Check the seams of padded or
down-filled items to prevent the risk
of fillings coming out. These could
catch fire when being dried.
– Disentangle the laundry.
– New dark coloured garments should
be washed and dried separately from
light coloured garments to avoid the
danger of colours running and disco‐
louring other garments or even plas‐
tic components in the dryer. Dark
coloured fibres can also settle on
light coloured garments and vice ver‐
sa.
– Tie together textile belts and ties.
– Fasten . . .
. . . duvet covers and pillow cases to
prevent small items from being trap‐
ped inside them.
. . . hooks and eyes.
– Sew in or remove underwiring from
bras.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– Leave jackets open and undo any
long zips so that textiles dry evenly.
– Minimum iron fabrics tend to crease
more, the greater the load. This is al‐
so the case for garments made from
very fine weave fabric, such as shirts
or blouses. If necessary, reduce the
size of the load for these types of
fabric.
Preparing the laundry before
drying
Make sure that any objects, e.g.
detergent dosing balls, lighters etc.
have been removed from the laun‐
dry.
They could melt or explode and
cause damage to the dryer or the
laundry.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Notes on correct laundry care
Garment care label symbols
Drying
– Down-filled garments have linings
which have a tendency to shrink, de‐
pending on the quality of the item.
They can be partially dried using the
Gentle smoothing programme.
Normal/higher temperature
Reduced temperature:
Select Gentle tumble (for delicate
textiles)
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the care label, as
the surface of the fabric may other‐
wise become rough. They can be
partially dried using the Gentle
smoothing programme.
Do not tumble dry
Ironing
Very hot
Hot
– Woollens and wool blends tend to
become matted and shrink if dried in
a tumble dryer. They can, however,
be "fluffed up" in the Woollens hand‐
care programme.
Warm
Do not iron
Laundry care when drying in a
tumble dryer
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry
these textiles. When purchasing
these garments it is advisable to take
their shrinkage properties into ac‐
count.
See the "Programme chart".
This describes the programmes and
gives their maximum load.
– Load according to the optimum
amount of laundry recommended for
the programme being used. Under‐
loading is uneconomical. Overload‐
ing gives a poorer quality of drying
and may cause unnecessary creas‐
ing.
– Select the Gentle tumble option for
fabric which is particularly heat-sen‐
sitive or susceptible to creasing.
– With half loads you can select the
Auto load control option.
– Select an appropriate drying level,
e.g. . . .
. . . Normal +, if you want to fold and
put away the laundry after you take it
out of the dryer.
. . . Machine iron, if the laundry, e.g.
table linen, requires further process‐
ing after drying.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Load the tumble dryer
When closing the door make sure
that laundry does not get trapped in
the door opening.
It is essential to read "1. Notes
on correct laundry care" first of
all.
This could damage the laundry.
Press the button to switch the
dryer on.
The interior drum lighting will come on.
The interior drum lighting will automat‐
ically go out after a few minutes
and/or after the start of a programme
to save energy.
Open the door
If you are not using a fragrance fla‐
con: the tab must be pushed down
completely (see arrow).
Close the door
Reach under the door grip and pull
the door open.
Unfold the laundry and load loosely
into the drum.
Do not overload the drum.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
Shut the door with a gentle swing.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a programme and start it
Further programmes
Select a programme
The further programmes can be selec‐
ted via the display.
Turn the programme selector.
Different programmes and setting op‐
tions will light up in the display, de‐
pending on the position of the pro‐
gramme selector.
Automatic plus
Touch the or sensor to scroll
through the list until the programme
you want appears in the display.
When a programme is selected, the
maximum load (weight of dry laundry)
possible for the programme will ap‐
pear in the display for a few seconds.
You can confirm with OK or wait until
the pre-set drying level or programme
duration lights up.
Confirm by touching the OK sensor.
If you think you have loaded too
much laundry, remove a few items.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a programme and start it
Programmes with drying levels
Other programmes and the timed
drying programmes
– Cottons, Minimum iron, Delicates,
Denim, Shirts, Express, Gentle
smoothing, Steam smoothing, Au‐
tomatic plus, Sportswear, Outer‐
wear
– Cottons , Woollens handcare,
Silks handcare, Proofing
The drying level is preset and cannot
be altered.
The drying level can be altered after
selecting one of these programmes.
– Cool air, Warm air, Basket pro‐
gramme
Press the Drying level button.
You can select the duration in ten-mi‐
nute stages.
The currently selected drying level will
appear marked with a in the display.
Cool air: 20 min - 1:00 h
Warm air: 20 min - 2:00 h
Basket programme: 40 min - 2:30 h
Normal
Touch the or sensor to scroll
through the list until the drying level
you want is highlighted.
Press the Duration button.
Duration
0:20
h
Confirm by touching the OK sensor.
The sensor is used to increase the
duration, the sensor to reduce it.
Any drying level can be selected for the
Cottons and Express programmes. A
more limited range is available when
using the other programmes.
Confirm by touching the OK sensor.
Important: When selecting the
Steam smoothing programme, you
must make sure that the condensed
water container has been filled as
described in these operating instruc‐
tions (see "Cleaning and care").
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a programme and start it
Drying and the programme duration will
Select any options or delay
start (if required)
light up in the display. The drying level
reached will light up instead of Drying
later on, during programmes with a se‐
lectable drying level.
Options
The Perfect Dry indicator will only flash/
light up with programmes with selecta‐
ble drying levels (see also "Operating
the tumble dryer").
Cooling down will light up in the display
shortly before the end of the pro‐
gramme. The laundry will be cooled
down, however the programme is not
yet finished.
Press a button.
The button will light up when the option
is selected.
An option can only be selected when
the load indication has gone out in the
display.
Not all options can be combined or can
be selected/deselected: see "Options".
Please see "Options" for further infor‐
mation.
Delay start
Press the Delay start button to select
delay start.
Please see "Delay start" for more in‐
formation.
Start the programme.
Press the flashing Start/Stop button.
The Start/Stop button will now light up
constantly.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the laundry
End of programme/Anti-crease
Check that all items have been re‐
moved from the drum.
If items are left in the dryer, they
could be damaged by overdrying
when the dryer is next used.
At the end of the programme: Anti-
crease/Finish (if anti-crease has been
selected) or Finish will light up. The
Start/Stop button will no longer be lit
up.
If the dryer is switched on at the mains
and the door is opened, the drum light‐
ing will come on. It will go out a few mi‐
nutes later to save energy.
To save energy, 10 minutes after the
end of the programme the Start/Stop
button will begin to flash slowly and the
display will go out.
If the dryer is still switched on, switch
The dryer will switch off automatically
15 minutes after the end of the anti-
crease phase (with programmes without
an anti-crease phase it will switch off
15 minutes after the end of the pro‐
gramme).
it off with the button.
A buzzer will sound.
Remove the fluff from the 2 fluff filters
in the door opening: see "Cleaning
and care - Fluff filters".
Shut the door with a gentle swing.
Remove the laundry
Empty the condensed water contain‐
er.
Never open the door before the
drying process has finished.
Tip: The condensed water can be used
for the Steam smoothing programme.
See "Cleaning and care - Preparing the
condensed water container for Steam
smoothing".
Reach under the door grip and pull
the door open.
Remove the laundry.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
will not be removed as effectively from
parts of garments made of synthetic fi‐
bres.
Auto load control
This option should be used if you only
want to dry half the load given in the
display and quoted in the "Programme
chart". In this case, by pressing this
button, you can both shorten and opti‐
mise the drying process.
Anti-crease
The options are switched on or off by
pressing the appropriate button. Not all
options can be combined or can be se‐
lected/deselected
Depending on the programme selected,
the drum will continue to rotate in a
special rhythm for up to 2 hours at the
end of the programme, to reduce creas‐
ing, if you do not wish to remove the
laundry immediately.
The button will light up when the option
is selected.
Gentle tumble
Buzzer
Delicate fabric (with the symbol on
the care label, e.g. acrylic garments) is
dried at a lower temperature. The pro‐
gramme duration is longer.
A buzzer (four beeps at intervals for a
maximum of 1 hour) will sound to let
you know that the programme has fin‐
ished. The continuous buzzer which
sounds when there is a fault is not de‐
pendent on the setting for the buzzer at
the end of the programme.
Freshen up
You can use the Freshen up option to
help remove or reduce odours in clean
(dry or damp) clothing.
The drying air is heated for a specific
length of time. After this, the garments
are aired to the Normal drying level
without any more heat being added.
The drying level cannot be altered.
The option will be more effective if you
dampen the garments a little before‐
hand, use a fragrance flacon and re‐
duce the load. Please note that odours
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
The following options can be selected in addition to the pro‐
gramme:
Gentle
tumble1
Freshen
up1
Auto load
control1
Anti-
crease
Buzzer
–
X
X
–
–
X
X
–
–
–
X
–
X
–
–
–
–
–
–
–
–
–
–
X
X
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
X
X
X
–
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Cottons
Cottons
Minimum iron
Woollens handcare
Silks handcare
Gentle smoothing
Shirts
–
X
X
X
X
X
X
X
X
X
X
X
X
X
–
O
X
–
Express
Denim
X
–
Steam smoothing
Warm air
X
O
O
–
Automatic plus
Delicates
Proofing
Sportswear
Outerwear
O
O
–
Cool air
Basket programme
–
1 = These options cannot be combined with one another
X = Can be selected
O = Cannot be changed/always active
– = Cannot be selected
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Delay start
To select delay start
To begin delay start
With delay start you can delay the start
of the programme by up to a maximum
of 24 hours.
Press the Start/Stop button.
The display will show the delay start
time counting down in hours and mi‐
After selecting the programme, press nutes until the programme starts auto‐
the Delay start button.
matically.
The following will light up in the display: The drum will turn briefly every hour un‐
til the start of the programme to reduce
creasing.
Start in
00 : 00 h
To change delay start after it
has started counting down
Press the Delay start button.
The sensor will increase the dura‐
tion by 1 hour up to 24 hours. The
sensor reduces the duration.
Confirm by touching the OK sensor.
You can either start the programme im‐
mediately or change the time:
The cursor will change from the hours
to the minutes.
To do this touch the or sensor.
Set the minutes in the same way. The
minutes are selected in 15 minute in‐
crements.
Confirm by touching the OK sensor.
To add/remove laundry after
delay start has started count‐
ing down
You can open the door to add/
remove laundry.
Confirm by touching the OK sensor.
To change delay start (if necessary)
Press the Delay start button.
Select Change the time and change
Press the Start/Stop button so that
the delay start time continues to
count down.
it.
To delete delay start (if necessary)
Press the Delay start button.
To cancel delay start
Select Cancel the time and confirm
this with OK.
Press the Start/Stop button.
Cancel delay start will light up.
Confirm by touching the OK sensor.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Max. load 8.0 kg*
Cottons **
Use for
Cotton items such as those described under Cottons Normal with
normal residual moisture.
Note
– Items are dried to a Normal level only.
– The Cottons programme is the most energy-efficient for dry‐
ing cotton items with normal residual moisture levels.
Cottons
Max. load 8.0 kg*
Extra dry, Normal +, Normal, Slightly dry
Use for
Notes
Single and multi-layered cotton fabric such as towelling, jerseywear,
T-shirts, underwear, workwear, covers, flannelette bed linen and ba‐
by clothes.
– Select Extra dry for multi-layered and very thick fabric.
– Do not use Extra dry for jersey fabric (e.g. T-shirts, underwear), as
they have a tendency to shrink.
Hand iron , Hand iron , Machine iron
Use for
Cotton or linen fabric requiring further processing, e.g.: table linen,
bed linen, starched laundry.
Note
To prevent laundry from drying out it should be rolled up until you
are ready for ironing.
Minimum iron
Max. load 4.0 kg*
Normal +, Normal, Slightly dry, Hand iron , Hand iron
Use for
Minimum iron items made of cotton, synthetic or mixed fibre, e.g.:
workwear, tunics, tops, dresses, trousers, table linen and socks.
* Weight of dry laundry
** Note for test institutes:
Test programme in accordance with Regulation 392/2012/EU for energy labelling,
measured in accordance with EN 61121 (without any options selected)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Woollens handcare
Max. load 2.0 kg*
Use for
Woollen garments and fabric containing wool blends, e.g. pullovers,
jackets and socks.
Note
– Wool and wool blend items are only fluffed up; they are not dried
completely.
– Remove garments as soon as the programme has finished.
Silks handcare
Max. load 1.0 kg*
Use for
Silk garments which are suitable for drying in the tumble dryer, e.g.
blouses and shirts
Note
– This programme reduces creasing. Items are not dried completely
by this programme.
– Remove garments as soon as the programme has finished.
Gentle smoothing
Max. load 1.0 kg*
Normal, Hand iron
Use for
– Cotton and linen fabric
– Minimum iron items made of cotton, synthetic or mixed fibre, e.g.
trousers, jackets, shirts.
Notes
– Suitable for dry and damp laundry.
– Select Hand iron if the items are to be ironed after drying.
– Smooths out creasing caused during the spin cycle in the washing
machine.
– Remove garments as soon as the programme has finished.
Shirts
Max. load 2.0 kg*
Normal +, Normal, Slightly dry, Hand iron , Hand iron
Use for Shirts and blouses.
* Weight of dry laundry
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Express
Max. load 4.0 kg*
Extra dry, Normal +, Normal, Slightly dry, Hand iron , Hand iron , Ma‐
chine iron
Use for
Note
Garments suitable for the Cottons programme.
The programme duration is shorter.
Denim
Max. load 3.0 kg*
Max. load 1.0 kg*
Normal +, Normal, Slightly dry, Hand iron , Hand iron
Use for Denim garments, e.g. jeans, jackets, skirts, shirts
Steam smoothing
Normal, Hand iron
Use for
– Cotton and linen fabric
– Minimum iron items made of cotton, synthetic or mixed fibre, e.g.
trousers, jackets, shirts.
Notes
– For all items which require
– dampening before ironing.
– creasing to be removed.
– Select Hand iron if the items are to be ironed after drying.
– Water will be taken from the condensed water container during
this programme. This water will then be sprayed into the drum
from a jet in the door opening. The condensed water container
must therefore be filled with water up to at least the –min– marker.
– You will be aware of more operating noise because the con‐
densed water pump is running.
* Weight of dry laundry
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Warm air
Max. load 8.0 kg*
Use for
– Multi-layered fabric whose layers have different drying character‐
istics, e.g. jackets, pillows, sleeping bags and other voluminous
items.
– Drying individual items, e.g. bath towels, swimwear, tea-towels.
Note
Do not select the longest drying time to start with. Check the items
as you are drying them to find the optimum time.
Automatic plus
Max. load 5.0 kg*
Normal +, Normal, Slightly dry, Hand iron , Hand iron
Use for
Mixed loads of garments suitable for the Cottons and Minimum iron
programmes.
Delicates
Max. load 2.5 kg*
Normal +, Normal, Slightly dry, Hand iron , Hand iron
Use for
Delicate items with the symbol on the care label made of synthet‐
ic fibre, mixed fibre, rayon and easy care cotton, e.g. shirts, blouses,
lingerie and appliqued garments.
Note
Reducing the load will reduce creasing.
* Weight of dry laundry
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Proofing
Normal
Use for
Max. load 2.5 kg*
Drying microfibre fabric, skiwear, outerwear, fine, closeweave cotton
garments (poplin) or tablecloths which are suitable for drying in a
tumble dryer and have been treated to provide a water and dirt re‐
sistant finish.
Notes
– This programme includes a proofing fixing phase.
– Only use proofing agents containing fluorochemical compounds
which are stated by the manufacturer as being "suitable for use
on membrane textiles".
– Do not dry items which have been treated with proofing agents
containing paraffin. Fire hazard!
Sportswear
Max. load 3.0 kg*
Normal +, Normal, Slightly dry, Hand iron , Hand iron
Use for Sportswear which is suitable for drying in a tumble dryer.
* Weight of dry laundry
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Outerwear
Max. load 2.5 kg*
Normal, Hand iron
Use for
Cool air
Use for
Outerwear which is suitable for drying in a tumble dryer.
Max. load 8.0 kg*
Any item which only needs airing.
Basket programme
Max. load for basket 3.5 kg
Notes
– This programme may only be used with the Miele drying basket
(optional accessory) fitted.
– Use this programme to dry or air items which are suitable for dry‐
ing in a tumble dryer but which are not suitable for drying using
mechanical action.
– It is essential to observe the operating instructions for the drying
basket.
Use for
See the operating instructions supplied with the drying basket.
* Weight of dry laundry
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the programme sequence
You cannot change to another pro‐
gramme once a programme has started
(this prevents unintentional alterations).
Adding or removing laundry af‐
ter a programme has started
Press the Start/Stop button.
If you move the programme selector,
Change not possible will light up in the
display until you move the programme
selector back to the original pro‐
gramme.
Cancel programme will light up in the
display.
Confirm by touching the OK sensor.
– Cooling down will light up in the dis‐
play, depending on the drying dura‐
tion and the drying temperature
reached.
You will need to cancel the current pro‐
gramme before you can select a new
one.
– Wait until Finish lights up in the dis‐
play or press the Start/Stop button
again until Finish lights up.
Cancelling a programme while
it is running and selecting a
new programme
Press the Start/Stop button.
Danger of burning.
Do not touch the back of the drum
when adding or removing items. The
drum and the items can be very hot.
Cancel programme will light up in the
display.
Confirm by touching the OK sensor.
Add or remove items.
Close the door.
– Cooling down will light up in the dis‐
play, depending on the drying dura‐
tion and the drying temperature
reached.
To continue with the programme:
(change the drying level first of all, if
necessary)
– Wait until Finish lights up in the dis‐
play or press the Start/Stop button
again until Finish lights up.
Press the Start/Stop button.
Press the button to switch the dry‐
er off.
Programme duration
Altering the programme sequence can
cause the programme duration shown
in the display to be adjusted.
Press the button to switch the dry‐
er on.
Select and start a new programme
straight away.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Emptying the condensed water
container
The condensed water is collected in
the condensed water container.
Empty the condensed water contain‐
er after every drying programme.
Empty container will light up if the
maximum level of the condensed water
container is reached.
To delete Empty container: open and
close the door with the dryer switched
on.
Empty the container.
Replace the container in the dryer.
To prevent damaging the door
and the front of the condensed water
container when pulling the container
out of the dryer:
Condensed water should not be
consumed. It could lead to health
problems for people and animals.
The condensed water can be used for
the Steam smoothing programme. The
condensed water container must be fil‐
led to use this programme, see the fol‐
lowing section.
always close the door completely.
Pull out the condensed water con‐
tainer.
To prevent water running out, hold it
at the front and towards the back and
keep it in a horizontal position when
carrying it.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Preparing the condensed wa‐
ter container for Steam
smoothing
Condensed water which has col‐
lected in the condensed water con‐
tainer is directed into the drum in the
Steam smoothing programme. The
condensed water container must
therefore be filled with water up to at
least the –min– marker.
1 spout, 2 rubber seal
Pour the water in through the rings of
the spout 1.
Only use clean water. The water
must not contain any fragrance, de‐
tergent or other substances.
Check the rubber seal from time to
time.
If tap water is used frequently, white
limescale deposits can build up on the
rubber seal 2.
The –min– marker is at the front left-
hand side of the container.
Use a damp cloth to carefully remove
any limescale deposits from the rub‐
ber seal 2.
Make use of the condensed water
which collects during the drying
process.
After cleaning the rubber seal, push
the condensed water container fully
into the dryer.
If the condensed water container is
empty
You can fill the condensed water con‐
tainer with commercially available
condensed water (ironing water).
You should only use tap water in excep‐
tional circumstances. If tap water is
used frequently, the Steam smoothing
spray jet (in the door opening) can be‐
come calcified.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Fluff filters
This tumble dryer has 2 fluff filters in
the door opening: the upper and lower
fluff filters trap fluff produced during
the drying process.
Removing visible fluff
Remove any fluff after every drying
cycle.
Tip: You can also use a vacuum cleaner
so that you can remove the fluff without
touching it.
Remove the fluff (see arrows) . . .
Open the door.
You must remove the fragrance
flacon (if present) beforehand. See
"Fragrance flacon".
. . . from the surfaces of all the fluff
filters.
. . . from the perforated laundry de‐
flector.
Push the upper fluff filter back into
position until it clicks.
Pull the upper fluff filter forwards to
remove it.
Close the door.
If there is a great deal of compacted
fluff carry out the following proce‐
dure.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the fluff filters and air flow
openings thoroughly
Hold the dial and pull the fluff filter
forwards to remove it.
If the drying duration has become
longer or the surface of the filters is
visibly compacted with fluff, you
should carry out the following clean‐
ing procedure.
If using a fragrance flacon make
sure you remove it beforehand.
Pull the upper fluff filter forwards to
remove it.
Use a vacuum cleaner with a long
crevice nozzle attached to remove
any visible fluff from the upper air
flow openings.
Cleaning the fluff filters with water
Flush the fluff filters through with hot
running water.
Shake the fluff filters thoroughly and
then dry them carefully.
Ensure the filters are dry before
replacing them. Wet filters could
cause operational faults.
Turn the yellow dial on the lower fluff
filter in the direction of the arrow (until
you hear it click).
Push the lower fluff filter in complete‐
ly and lock it with the yellow dial.
Push the upper fluff filter in complete‐
ly.
Close the door.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Removing the plinth filter will cause the
right hand guide pin in the dryer to
come out. This pin ensures that the
heat exchanger access panel can only
be closed if the plinth filter is inserted
the right way round.
Plinth filter
Only clean the plinth filter when
Clean out airways lights up.
To delete Clean out airways: Switch the
dryer off and back on again / confirm
OK.
Cleaning the plinth filter
Removing the plinth filter
Pull the handle out of the plinth filter.
Clean the filter thoroughly under run‐
ning water.
Press the round, indented area on the
Squeeze the plinth filter thoroughly.
heat exchanger access panel to open
it.
The plinth filter must not be re‐
placed dripping wet as this can
cause a fault.
The panel will spring open.
Use a damp cloth to remove any fluff
from the handle.
Pull the plinth filter out by the handle.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the plinth filter panel
Checking the condenser unit
Danger of injury. Do not touch
the cooling fins. You could cut your‐
self.
Look to see if fluff has accumulated.
If there is visible soiling:
Clean using a vacuum cleaner
with a dusting brush attached. Care‐
fully pass the vacuum cleaner brush
over the heat exchanger cooling fins
without applying any pressure. Oth‐
erwise the cooling fins could be bent
out of shape or become damaged.
Use a damp cloth to remove any fluff.
Make sure that you do not damage
the rubber seal when doing this.
Check whether the cooling fins are
blocked with fluff (as follows).
Carefully vacuum up any visible fluff
or soiling.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Replacing the plinth filter
Close the heat exchanger access
panel.
The dryer can only be operated
with the plinth filter fitted correctly
and the heat exchanger access pan‐
el closed. The access panel must be
closed correctly to ensure that water
cannot leak from the condenser sys‐
tem and to ensure that the dryer
functions efficiently.
Fit the filter back on the handle. Make
sure it is the correct way round.
To ensure that the filter is positioned
correctly in the front of the heat ex‐
changer unit:
First insert the handle with the plinth
filter attached over the two guide
pins.
– The word Miele on the handle must
be the correct way up.
Push the plinth filter in completely.
The act of pushing in the plinth filter will
also push in the right hand guide pin.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Tumble dryer
Disconnect the tumble dryer
from the mains electricity supply.
Do not use solvents, abrasive
cleaners, glass cleaners or all-pur‐
pose cleaners.
These could damage plastic surfa‐
ces and other parts.
Clean the tumble dryer with a slightly
damp cloth and a mild non-abrasive
cleaning agent or a solution of wash‐
ing-up liquid and water.
Clean the seal around the inside of
the door with a damp cloth.
Dry all parts with a soft cloth.
The drum and other stainless steel
parts can be cleaned with a suitable
proprietary stainless steel cleaner fol‐
lowing the manufacturer's instruc‐
tions.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
Using a fragrance flacon (optional ac‐
cessory) will add a pleasant fragrance
to your laundry.
Before using a fragrance flacon,
please read "Warning and safety in‐
structions - Using a fragrance flacon
(optional accessory)".
Inserting a fragrance flacon
Only hold the fragrance flacon as il‐
lustrated. Do not hold it at an angle
or tip it as the fragrance will leak out
of the flacon.
Open the cover using the tab until the
tab is at the top right hand side as
shown.
Insert the flacon in the opening as far
as it will go.
Hold the flacon securely to prevent
opening it by mistake.
Pull off the protective seal.
Open the door of the tumble dryer.
The fragrance flacon is inserted in the
upper fluff filter in the opening on the
right hand side beside the grip.
If you are not using a fragrance fla‐
con: the cover must always remain
closed (push the cover down com‐
pletely with the tab).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
– You will feel a slight resistance and
hear a soft click.
Markers and must line up with
one another.
Marker must be in position : this
is the position at which you can feel
a resistance.
Before drying
You can select the intensity of the fra‐
grance.
Turn the outer ring clockwise a lit‐
tle.
Turn the outer ring clockwise: the fur‐
ther you open the flacon, the more in‐
tense the fragrance.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
Damp laundry and longer drying dura‐
tions with sufficient heat transfer are
needed for the fragrance to be released
into the laundry effectively. The fra‐
grance will also be noticeable in the
room air during the process. Fragrance
is not released when using the Cool air
programme.
Replacing the fragrance flacon
When the fragrance is no longer suffi‐
ciently intense:
After drying
To avoid the fragrance escaping need‐
lessly:
Turn the outer ring anti-clockwise un‐
til markers a and b line up.
Turn the outer ring anti-clockwise un‐
til marker b is in position _.
– You will feel a slight resistance.
If you want to dry laundry without
adding fragrance occasionally: remove
the fragrance flacon and store it in its
original packaging until you want to
use it again. See the following section.
Replace the fragrance flacon with a
new one.
Fragrance flacons are available to or‐
der from Miele or online at
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
– when purchasing new fragrance fla‐
cons: only remove the protective seal
just before use
Cleaning the fluff filters
The intensity of the fragrance will be di‐
minished if the fluff filters and the plinth
filter are not cleaned.
The fragrance filter must be re‐
moved before cleaning the fluff filter.
To prevent any fragrance leaking
out of the flacon:
when not in use, the fragrance flacon
must only be stored in its original
packaging as illustrated.
Never lay the fragrance flacon
down on any surface as the fra‐
grance will leak.
Only store the fragrance flacon in its
original packaging
Clean the fluff filters and the plinth fil‐
ter: see "Cleaning and care".
– when storing the fragrance flacon in
its original packaging whilst you are
not using it, e.g. whilst cleaning the
tumble dryer: to prevent the fra‐
grance leaking do not store the pack‐
aging upright on its edge or upside
down.
– store in a cool, dry place
– store away from direct sunlight
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes minor faults in the performance of the appli‐
ance, some of which may result from incorrect operation, can be put right without
contacting the Service Department.
Repair work to electrical appliances must only be carried out by a suitably
qualified person in strict accordance with current local and national safety regu‐
lations. Repairs and other work by unqualified persons could be dangerous.
The manufacturer cannot be held liable for unauthorised work.
Some of the messages in the display are more than one line long. Touch the or
sensor to read them in full.
Messages in the display
Problem
Cause and remedy
lights up after
Access via a code has been activated.
switching on
See "Settings menu, Code".
This is not a fault.
Adjust the load See
lights up after a pro‐
gramme is cancelled
In some programmes, if the drum has been underloa‐
ded or is empty, the programme will be cancelled.
This can also happen if the items are already dry.
Open and close the door to resume drying.
Dry individual items using the Warm air timed dry‐
ing programme.
No obvious cause.
Switch the dryer off and then on again.
Start a programme.
Service Fault F
lights up after a pro‐
gramme is cancelled
If the programme is cancelled again and an error
message appears, there is a fault. Contact the Miele
Service Department.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Cause and remedy
There is a build-up of fluff in the airways.
Clean the fluff filters.
Clean the plinth filter.
Clean out airways lights
up at the end of a pro‐
gramme
See "Cleaning and care".
To switch off the message:
Confirm with OK.
An excessive amount of fluff has built up.
Clean the fluff filters.
Clean the plinth filter.
Clean out airways See
lights up after a pro‐
gramme is cancelled
Clean the airways:
clean the area underneath the plinth filter
clean the heat exchanger.
To switch off the message:
Switch the dryer off and back on again.
The condensed water container is full or there is kink
in the drain hose.
Empty the container.
Empty container see
lights up after a pro‐
gramme is cancelled
Check the drain hose.
To switch off the message:
Open and close the door while the dryer is switch‐
ed on or switch the dryer off and back on again.
This is to remind you that water is taken from the
condensed water container when the Steam smooth‐
ing programme is being used.
Fill condensate container
The condensed water container must be filled with
water to at least the –min– marker.
Confirm with OK.
This is to remind you to load the laundry when the
Steam smoothing programme is selected.
Load the laundry in the drum.
Open & close door
Comfort cooling
The programme has finished but the laundry has not
yet cooled down.
Either remove the laundry and spread it out to cool
down or leave it in the tumble dryer to cool down
during the cooling phase.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Unsatisfactory drying results
Problem
Cause and remedy
The laundry is not suffi‐ The load consisted of different types of fabric.
ciently dry
Finish drying using the Warm air timed drying pro‐
gramme.
Select a different programme next time.
Tip: You can alter the residual moisture level for some
programmes. See "Settings menu".
Laundry or feather filled The laundry was washed with insufficient detergent
pillows smell after dry‐
ing
Feathers are a natural product and this is quite nor‐
mal.
Laundry: use sufficient detergent next time.
Pillows: take out of the tumble dryer and air them.
Use a fragrance flacon (available as an optional
accessory) for your favourite fragrance.
Items made of synthetic Synthetic fibres tend to attract static charge.
fibres are charged with
static electricity after
drying
Static charge can be reduced by adding a fabric
conditioner to the final rinse in the washing pro‐
gramme.
There is a build-up of
fluff
Fluff is principally the result of friction when garments
are being worn and to some extent when they are be‐
ing washed. Machine drying hardly causes any fluff to
form.
Fluff is collected by the fluff filters and the plinth filter
and can be removed easily.
See "Cleaning and care".
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Other problems
Problem
Cause and remedy
The drying process
goes on too long or
even switches off *
The room in which the dryer is located is too warm.
Ventilate the room thoroughly.
Detergent residues, hair and fine fluff can clog the fil‐
ters.
Clean the fluff filters and the plinth filter.
Remove any visible fluff:
. . . bottom left, from behind the panel in the heat
exchanger cavity (see "Cleaning and care");
. . . from the cooling fins behind the grille bottom
right (see the end of this section).
The cool air intake (bottom right grille) is blocked.
Move any objects, such as a laundry basket, away
from the dryer.
The fluff filters and the plinth filter were wet when re‐
placed.
The fluff filters and the plinth filter must be dry.
The laundry is too damp.
Spin using a higher spin speed in the washing ma‐
chine.
The tumble dryer has been overloaded
Do not exceed the maximum load for the pro‐
gramme selected.
Metal zips have prevented the dryer from registering
the correct moisture level.
Open the zips next time.
If the problem recurs, dry these items using the
Warm air timed drying programme.
* Before starting another programme:
Switch the dryer off and then on again.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Cause and remedy
There are humming
noises
This is not a fault.
The compressor (heat pump) is operating or you have
selected the Steam smoothing programme.
No action is required. These noises are quite nor‐
mal and can be heard when the compressor or the
condensed water pump is operating.
A programme does not
start
No obvious cause.
Connect the tumble dryer to the mains
Turn on the tumble dryer
Close the door
Check whether the mains fuse has tripped
Has there been a power cut? When power is restored
any previously running programme will restart auto‐
matically.
The display is dark and The dryer is in standby mode. This is quite normal
the Start/Stop button is and does not indicate a fault.
flashing slowly
The drum will turn at intervals in the anti-crease
phase.
See "Settings menu, Dark display".
The dryer is switched
off at the end of the
programme
The dryer switched off automatically. This is quite
normal and does not indicate a fault.
See "Settings menu, Appliance switch-off".
The interior drum light‐
ing does not come on
The drum lighting will switch off automatically ...
... when the door is closed.
... after a few minutes when the door is open (to save
energy).
If the dryer is switched on, the drum lighting will
come on when the door is opened.
Insufficient spray to re‐ The filter in the condensed water container is
moisten the laundry
blocked.
Clean the filter in the condensed water container
(optional accessory): see end of this section.
The spray jet in the door opening is heavily calcified.
Replace the spray jet (optional accessory): see
end of this section.
Only use condensed water. Do not use tap water.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Bottom right grille
Danger of injury. Do not touch
the cooling fins. You could cut your‐
self.
In general, the cooling fins be‐
hind the grille on the bottom right do
not need cleaning. They should only
be cleaned if the drying process is
taking an exceptionally long time due
to a very high level of dust or fluff in
the room in which the dryer is loca‐
ted.
Use a vacuum cleaner with a
dusting brush attached to clean the
cooling fins. Only pass the vacuum
cleaner brush over them lightly, with‐
out applying any pressure.
Take care not to bend the cooling
fins out of shape or to damage them.
First open the plinth filter panel (bot‐
tom left).
Carefully vacuum up any visible fluff
Then insert a spoon handle behind
or soiling.
the grille on the right hand side.
Re-insert the 3 hooks on the grille in‐
to the appropriate holes in the front
of the dryer.
Lever off the grille at the top (1.).
Lever off the grille at the bottom (2.).
Open the grille out to the right (3.) ...
Press the grille firmly back into posi‐
tion by pressing it in at the top and
bottom on the left.
... and pull it forwards releasing its 3
hooks to remove it from the dryer.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Fluff filter in the condensed
water container
If you are experiencing problems
running the Steam smoothing pro‐
gramme, the fluff filter at the end of
the hose which is connected to the
rubber seal in the condensed water
container could be blocked.
Guide the end of the hose through
the opening and hold it securely with
one hand.
Use your other hand to pull the fluff
filter off the hose.
Rinse the fluff filter with a jet of water
until all the fluff has been removed.
Refit the cleaned fluff filter onto the
hose.
Pull out the condensed water con‐
tainer.
Now feed the hose with its fluff filter
attached into the condensed water
container.
Replace the spout in the condensed
water container. Make sure it is the
correct way round (see the illustra‐
tion).
Remove the spout by holding the
side lug and pulling upwards.
To avoid detaching the hose be care‐
ful not to tug on it.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Open the door of the tumble dryer.
Steam smoothing spray jet
The spray jet is located in the top left of
the door opening.
Limescale deposits will impair
the spray jet.
In this case, the spray jet must be re‐
moved and replaced with a new one
(see "Optional accessories").
The spray jet can only be replaced us‐
ing the special tool supplied with the
new spray jet.
Do not use any other tool as this
would damage the spray jet or the
dryer.
Steam smoothing must never be
used without the spray jet fitted and
screwed in correctly.
Attach the tool to the spray jet.
Turn the tool anti-clockwise to un‐
screw the spray jet.
Insert the new spray jet in the tool.
Turn the tool clockwise to screw the
spray jet securely in position.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
Repairs
Optional accessories
In the event of any faults which you
Optional accessories for this tumble
cannot remedy yourself, please contact dryer are available from Miele, your
your Miele Dealer or the Miele Service
Department.
Miele dealer or via the internet at:
Contact details for Miele are given at
the end of this booklet. N.B. A call-out
fee will be charged for service visits
where the problem could have been
resolved as described in these in‐
structions.
Dryer basket
The dryer basket is suspended in the
drum and does not rotate with the
drum. This enables items which must
not be subjected to mechanical action
to be dried or aired.
When contacting the Service Depart‐
ment, please quote the model and seri‐
al numbers both of which are given on
the data plate (visible when the door is
open).
Fragrance flacon
A fragrance flacon can be used in your
tumble dryer to add a pleasant fra‐
grance to your laundry.
Guarantee: U.K.
In the U.K. the appliance is guaranteed
for 2 years from the date of purchase.
However, you must activate your cover
by calling 0330 160 6640 or registering
Guarantee: Other countries
For information on the appliance guar‐
antee specific to your country please
contact Miele. See end of this booklet
for contact details.
Please note that telephone calls may
be monitored or recorded for training
purposes.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Front view
a
e
Mains connection cable
Heat exchanger access panel
– do not open during drying
b
Control panel
f
Four height adjustable screw feet
c
Condensed water container
g
Cool air intake grille
– empty after every drying cycle
– do not obstruct with a laundry
basket or other objects
d
Door
– do not open during drying
h
Hose for external drainage of con‐
densed water
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Rear view
If transporting the dryer at an an‐
gle, only tip towards the left side.
a
Protruding lid for holding when mov‐
ing the dryer (see arrows)
b
Accessories for external drainage of
condensed water: hose clip, adapter
and hose holder
c
Hose for external drainage of con‐
densed water
d
Mains connection cable
Transporting the dryer
To manoeuvre the dryer out of its pack‐
ing case to its installation site, hold it by
– the front feet
If the tumble dryer has not been
transported as described, then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply.
Otherwise the heat pump can be
damaged.
– and the lid where it protrudes at the
back of the appliance.
Only transport the dryer as
shown in the following illustrations.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Ventilation
Installation
Levelling the dryer
The cool air intake at the front of
the dryer must not be blocked or
covered. This would hinder a suffi‐
cient intake of cool air for the heat
exchanger.
Make sure the dryer door can be
opened without hindrance after in‐
stallation.
Do not block the gap between
the bottom of the tumble dryer and
the floor with plinth facings, deep
pile carpet etc. This would hinder a
sufficient flow of air to the dryer.
Air which is taken in to cool the heat
exchanger is then blown back out of
the dryer and warms up the air in the
room. It is therefore very important to
ensure adequate ventilation, e.g. by
opening a window. Otherwise drying
durations may be longer (increased en‐
ergy requirement).
The appliance must stand perfectly lev‐
el to ensure safe and proper operation.
Before moving the tumble dryer
again (e.g. when moving house)
After each use a small quantity of con‐
densed water will collect in the area of
the pump. This water can run out if the
tumble dryer is tipped up when it is be‐
ing moved. Recommendation: run the
Warm air programme for approximately
1 minute before moving the tumble dry‐
er. Any remaining condensed water will
then be fed into the condensed water
container or out through the drain hose.
The screw feet can be adjusted to com‐
pensate for any unevenness in the floor.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Optional accessories
– Building-under kit
Additional installation require‐
ments
For safety reasons the tumble
dryer must be disconnected from the
electricity supply before installation.
A building under kit is required if
the lid of the tumble dryer needs to
be removed in order to build it under
a worktop.
It must be installed/dismantled by a
suitably qualified fitter.
Building under a continuous work‐
top/in a row of kitchen units
It is very important to avoid a
build-up of heat. The warm air which
is expelled from the dryer must be
able to dissipate. Warm air which
cannot dissipate could cause a fault.
The lid of the tumble dryer is replaced
by the cover plate supplied with the
building under kit. It must be fitted by a
suitably qualified fitter to ensure electri‐
cal safety.
Fitting instructions are supplied with the
building-under kit.
– The electrical socket must be located
in an accessible position near the ap‐
pliance.
– Washer-dryer stack
– Drying durations may increase slight‐
ly.
The tumble dryer can be combined with
a Miele washing machine in a washer-
dryer stack. The appropriate Miele
washer-dryer stacking kit is required.
A build-up of heat can be avoided by:
– Adjusting the screw feet so that there
is a gap of at least 20 mm between
the floor and the bottom of the dryer.
– Plinth
The tumble dryer can be fitted on a
plinth with drawer (please note the
plinth may not be available in all coun‐
tries).
– Creating a gap for the dryer in the
kitchen furniture plinth facing.
– Creating ventilation gaps in the kitch‐
en unit.
Pushing the dryer under a worktop
This tumble dryer is suitable for push‐
ing under a worktop if there is space to
do this without removing the lid.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Installation conditions requiring a
non-return valve
External condensed water out‐
let
There is a risk of back-flow into
the dryer if a non-return valve is not
fitted.
Back-flow could damage the dryer
and also the room in which it is loca‐
ted.
Certain installation conditions, such
as those described below, require
the fitting of a non-return valve.
Notes
When drying is in progress, con‐
densed water is pumped into the con‐
densed water container through the
drain hose which is located at the
back of the dryer.
The condensed water can also be
drained away via the drain hose so that
the condensed water container does
not have to be emptied.
Maximum delivery head with non-return
valve fitted: 1.00 m
Drain hose length: 1.60 m
Maximum delivery head: 1.50 m
Maximum drain hose length: 4.00 m
Installation conditions requiring the fit‐
ting of a non-return valve:
– Drainage into a sink or floor gully
where the end of the hose is im‐
mersed in water.
The following optional accessories
are available:
– Connection to a sink drain outlet.
– an extension hose,
– Connection to a drainage system al‐
ready in use by another appliance,
e.g. a dishwasher or washing ma‐
chine.
– a non-return valve kit for connection
to an external water outlet. The kit in‐
cludes an extension hose.
The non-return valve has to be
fitted with the arrow pointing in the
direction of flow.
Otherwise water will not drain out of
the appliance.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Arranging the drain hose
Do not pull on the drain hose
and do not stretch it or allow it to be‐
come kinked.
This could damage the hose.
There will be a small amount of residual
water left in the drain hose. Have a con‐
tainer ready to collect this.
Guide the hose to the right or left
side of the dryer, as required.
– If you are guiding it to the right you
can fit the hose into the groove.
– Leave the hose in the lower holder to
prevent it from being kinked by mis‐
take.
Pull the drain hose off its connection.
Unwind the hose and pull it carefully
out of the holders.
Allow any residual water to run into
the container.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Examples
Direct connection to a sink drain out‐
let
– Drainage into a sink or floor gully
Use the hose holder to prevent the
drain hose from becoming kinked.
Remove the following from the back
of the dryer at the top: Adapter 1 and
hose clip 3 behind it.
Press the small catches on the left
and right of the hose holder with your
thumbs (black arrows) and ...
Connect the drain hose as described
below.
... pull the hose holder forwards to re‐
move it (white arrows).*
If you want to drain the water off
into a sink or basin, you will need to
secure the hose carefully, e.g. by ty‐
ing it to a tap, to make sure it cannot
slip during use (see the drawing un‐
der "Installation and connection -
Front view").
Overflowing water can cause dam‐
age.
The non-return valve can be fitted in
the end of the hose.
* You can refit the hose holder at a
later stage if you decide that you no
longer want to drain the condensed
water externally.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Fit adapter 1 to the sink drain outlet
using nut 2.
The nut is usually fitted with a washer
which must be removed.
Attach the end of the hose 4 to
adapter 1.
Use the hose holder.
Use a screwdriver to tighten hose clip
3 up close to the nut.
Fit non-return valve 5 to tumble dryer
drain hose 6.
Non-return valve 5 has to be fitted so
that the arrow points in the direction
of flow (i.e. towards the sink).
1. Adapter
2. Nut
Secure the non-return valve using
hose clips.
3. Hose clip
4. End of the hose (secured with the
hose holder)
5. Non-return valve
6. Tumble dryer drain hose
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out The fuse cover must be refitted when
by a suitably qualified and competent
person, in strict accordance with cur‐
rent national and local safety regula‐
tions (BS 7671 in the UK).
changing the fuse, and if the fuse cover
is lost, the plug must not be used until
a suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is em‐
bossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the ap‐
pliance until after installation work has
been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for con‐
nection to a 230-240V mains supply.
Replacement fuses should be ASTA ap‐
proved to BS 1362 and have the cor‐
Please ensure the connection data quo‐ rect rating. Replacement fuses and fuse
ted on the data plate match the house‐
hold mains supply.
covers may be purchased from your lo‐
cal electrical supplier.
Connection should be made via a suita‐
ble switched socket which is easily ac‐
cessible after installation.
WARNING: THIS APPLIANCE
MUST BE EARTHED
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a quali‐
fied electrician for advice.
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption data
Final spin speed in a Residual Energy Duration
domestic washing ma‐ moisture
chine
1
Load
kg
8.0
rpm
1000
%
60
kWh
2.14
min
156
2
Cottons
4.0
8.0
1000
1200
60
53
1.28
1.90
94
141
Cottons Normal
8.0
8.0
1400
1600
50
44
1.80
1.60
134
119
Cottons Normal
+ Gentle tumble
Cottons Hand iron
8.0
8.0
1000
1000
60
60
2.19
1.52
163
115
8.0
8.0
1200
1400
53
50
1.35
1.25
101
94
8.0
4.0
1600
1200
44
40
1.05
0.69
80
55
Minimum iron Normal
+ Gentle tumble
4.0
4.0
5.0
2.0
2.5
3.0
4.0
1200
1200
800
600
800
40
40
50
60
50
60
60
0.80
0.60
1.43
0.75
0.88
1.42
1.20
60
48
106
60
68
106
88
Minimum iron Hand iron
Automatic plus Normal
Shirts Normal
Outerwear Normal
Denim Normal
900
1000
Express Normal
1
Weight of dry laundry
2
Test programme in accordance with Regulation 392/2012/EU for energy labelling, measured in ac‐
cordance with EN 61121
All data was calculated using EN 61121 unless otherwise stated.
Power consumption when switched off
Power consumption when not switched off
0.10 W
2.50 W
Note for test institutes:
For testing in accordance with EN 61121, before testing, dry a 3 kg load of cotton laundry with 70%
residual moisture as per the above standard using the Cottons Normal programme without any options
selected.
Consumption data can vary from the nominal values given above depending on the size of the
load, type of fabric, residual moisture level after spinning, fluctuations in the electricity supply
and any options selected.
The consumption data shown in the EcoFeedback display can vary from the consumption data quo‐
ted here. The variations arise from the way the data is measured in the dryer. For example, the pro‐
gramme duration may vary depending on the residual moisture present in the laundry and the type of
fabric which will affect the energy requirement.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Height
850 mm
596 mm
636 mm
1054 mm
Width
Depth
Depth with door open
Height for building under
Width for building under
Depth for building under
Suitable for pushing under a worktop
Suitable for stacking
Weight
820 mm (+8/-2 mm)
600 mm
600 mm
Yes
Yes
Approx. 61 kg
Drum volume
120 litres
Load size
8.0 kg (weight of dry laundry)
Capacity of condensed water container 4.8 litres
Hose length
1.60 m
Maximum delivery head
Maximum drain hose length
Length of connection cable
Voltage
1.50 m
4.00 m
2.00 m
See data plate
See data plate
See data plate
See data plate
See "Consumption data"
Class 1
Connected load
Fuse rating
Test certificates awarded
Energy consumption
LEDs
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
Changing a setting
Calling up settings
Touching the or sensor will call
up the different options for the set‐
ting.
You can use the Settings menu to alter
the dryer's electronics to suit different
requirements. Settings can be altered
at any time.
For example, you can
– select a value. If the option is marked
Opening the Settings menu
with a , it is active,
Switch the dryer on.
– change a bar chart,
The programme selector must not be at
the Further programmes position.
– change numbers.
Confirm by touching the OK sensor.
Touch the and sensors at the
same time.
Closing the Settings menu
The following will light up in the display:
Touch the or sensor repeatedly
until Back appears in the display.
Language
Confirm by touching the OK sensor.
You are now in the Settings menu.
Language
Selecting a setting
The display can be set to appear in
one of several different languages.
Touch the or sensor until the
setting you want appears in the dis‐
play.
The flag after the word Language
acts as a guide to prevent a language
which will not be understood from be‐
ing set.
– The sensor scrolls down the list.
– The sensor scrolls up the list.
Confirm by touching the OK sensor.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
Drying levels
Airways indicator
You can alter the drying levels for the
Cottons, Minimum iron and Automatic
plus programmes.
Fluff should be removed after drying.
The Clean out airways message will
remind you to clean the filters when a
certain amount of fluff has collected in
them. You can decide at what level of
fluff this reminder should be given.
The setting selected is shown in a bar
chart.
Factory default: a medium setting
You will have an idea of how often this
should be done after a few drying pro‐
grammes.
– Damper
The programme duration is shorter.
Options
– Drier
The programme duration is longer.
– Off
Clean out airways does not appear.
In cases of a very severe blockage in
the airways, the programme will be
cancelled and the Clean out airways
message will appear regardless of
this option.
Exception:
The Cottons programme will re‐
main unchanged.
Extended cool down
The automatic cooling down phase
which takes place before the end of a
programme can be extended for all
programmes with selectable drying
levels in 2 minute increments up to 18
minutes. This makes the garments
easier to handle.
– Heavy
Clean out airways only appears when
there is a heavy build-up of fluff.
– Normal (factory default)
– Light
Clean out airways appears when
there is only a small build-up of fluff.
Options
– 00 minutes (factory default)
– 02, 04, 06 ... 18 minutes
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
150 μS. Contact your local water au‐
thority for the conductivity level of your
mains water supply.
Buzzer volume
The buzzer can be set to be louder or
quieter.
Only activate the Low option for
the conditions described above.
Otherwise drying results can be un‐
satisfactory.
The setting selected is shown in a bar
chart.
Factory default: a medium setting.
– Quieter
Total consumption
– Louder
You can display the total consump‐
tion.
You will hear the buzzer change as the
setting is selected.
Options
Keypad tone
– Display
When this function is activated a tone
will sound each time a button is press‐
ed.
The total consumption is displayed in
kWh.
– Reset function
Options
The total consumption to date will be
deleted with the Reset option.
– On
– Off (factory default)
Conductivity
The Low option should only be
selected if the residual moisture
reading in your laundry is incorrect
due to extremely soft water.
Options
– Normal (factory default)
– Low
Conditions
The Low option should only be set if the
water used for washing the laundry is
extremely soft with a conductivity read‐
ing (electrical conductivity) of less than
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
Code
Dark display
The code prevents your dryer being
used without your knowledge.
To save energy the display and but‐
tons will go out after 10 minutes and
the Start/Stop button will flash slowly.
You can alter this setting.
Options
– Activate
Options
The code is 250 and can be activa‐
ted.
When the code has been activated,
you have to enter the code after
switching the dryer on. Otherwise the
dryer cannot be operated.
– On (factory default)
The display will go out (after 10 mi‐
nutes):
– if a programme is not selected af‐
ter the dryer has been switched on
– Deactivate
– during the current programme
– after the end of a programme.
For using the dryer without entering
the code. This only appears if the
code has been activated previously.
– On (not in current programme)
The display will go out (as described
above) but will remain on while the
programme is running.
– Change
You can enter a code of your own.
Important. Make a note of your
new code. If you forget the code, the
dryer will need to be unlocked by the
Miele Service Department.
– Off
The display will remain on (i.e. it will
never go out).
You can switch the display and buttons
back on again by pressing any button.
Display brightness
The brightness of the display can be
altered.
The setting selected is shown in a bar
chart.
Factory default: a medium setting.
– Darker
– Brighter
You will see the brightness change as
the setting is selected.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
Appliance switch-off
Anti-crease
To save energy the dryer will switch
off automatically after 15 minutes. You
can lengthen or shorten the time.
If you have pressed the Anti-crease
button:
the drum will continue to rotate in a
special anti-crease rhythm for a maxi‐
mum of 2 hours after the end of the
drying process. This helps prevent
creasing if laundry is not going to be
removed immediately. You can reduce
the duration of the anti-crease phase.
The dryer will switch off after 10, 15 or
20 minutes,
– if no further selection is made after
switching the dryer on
– at the end of the anti-crease phase
Options
– after a programme without an anti-
crease phase has finished.
– 1 hr
However, there is no automatic switch-
off in the event of a fault.
– 2 hr (factory default)
Options
– after 10 minutes
– after 15 minutes (factory default)
– after 20 minutes.
Memory
The electronics will store in memory a
drying level or options for a selected
programme. The duration selected for
a timed drying programme will also be
stored in memory. These settings will
then appear the next time the pro‐
gramme is chosen.
Options
– Off (factory default)
– On
Exception:
The Cottons programme will re‐
main unchanged.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: [email protected]
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1, Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
Australia
Miele Australia Pty. Ltd.
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353, Fax: (03) 9764 7149
New Zealand
Miele New Zealand Limited
8 College Hill
Freemans Bay, Auckland 1011, NZ
Tel: 0800 464 353, Fax: +64 9378 0146
China
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
Singapore
Miele Pte. Ltd.
163 Penang Road
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1331, Fax: (852)2610 1013
Email: [email protected]
# 04 - 03 Winsland House II
Singapore 238463
Tel: +65 6735 1191, Fax: +65 6735 1161
E-Mail: [email protected]
South Africa
Miele (Pty) Ltd
63 Peter Place, Bryanston 2194
P.O. Box 69434, Bryanston 2021
Tel: (011) 875 9000, Fax: (011) 875 9035
E-mail: [email protected]
India
Miele India Pvt. Ltd.
Ground Floor, Copia Corporate Suites
Plot No. 9, Jasola
New Delhi - 110025
Tel: 011-46 900 000, Fax: 011-46 900 001
United Arab Emirates
Miele Appliances Ltd.
P.O. Box 11 47 82
Ireland
Miele Ireland Ltd.
Gold & Diamond Park
Sheikh Zayed Road
Building 6 / Offices Nos. 6-214 to 6-220
Dubai
2024 Bianconi Avenue
Citywest Business Campus, Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
Tel: +971-4-341 84 44
Fax: +971-4-341 88 52
E-Mail: [email protected]
Manufacturer: Miele & Cie. KG
Carl-Miele-Straße 29, 33332 Gütersloh, Germany
75
Download from Www.Somanuals.com. All Manuals Search And Download.
TKG 440 WP
en-GB
M.-Nr. 09 696 880 / 02
Download from Www.Somanuals.com. All Manuals Search And Download.
|