DEALER SET-UP INSTRUCTIONS for EUROPEAN SNAPPER
21” STEEL DECK “M” MODEL WALK BEHIND MOWERS
This SNAPPER Walk Behind Mower uses a handle engine control bail system to kill the engine for the SAFETY of
the operator. These mowers are designed for quick set-up. The checklist on Page 4 should be filled out by the
dealer as the items are checked off and/or performed and the Consumer/Operator Product Registration card filled
out and sent to the Customer Service department at SNAPPER when completed. CAUTION: Cutting blades are
extremely sharp. Wear heavy leather gloves when handling or working with blades. Be careful to avoid cutting
yourself on sharp edges of blade.
STEP 3: Raise upper and lower handle until it seats into
position in the lower handle brackets. Securely tighten
PUSH MODELS
lower handle T-Knobs on both sides. See Figure 3.
STEP 1: Remove mower from shipping carton. Mower
shown as removed from shipping carton with handles
folded in Figure 1.
UPPER HANDLE &
LOWER HANDLE
SHOWN IN POSITION
LOWER
HANDLE
T-KNOB
MOWER SHOWN AS REMOVED FROM SHIPPING
CARTON WITH HANDLES FOLDED (PUSH
MODEL SHOWN)
FIGURE 1
STEP 2: Remove and discard cardboard from between all
handles. Raise upper handle until it is in line and seats
into lower handle. Securely tighten upper handle T-Knobs
FIGURE 3
on both sides. See Figure 2.
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil from crankcase will saturate the air
filter and cause the engine to be hard to start or not start
at all. If contamination does occur, the air filter will have to
be replaced.
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil from crankcase will saturate the air
filter and cause the engine to be hard to start or not start
at all. If contamination does occur, the air filter will have to
be replaced.
UPPER
HANDLE
T-KNOB
LOWER
HANDLE
UPPER
HANDLE
LOWER
HANDLE
T-KNOB
STEP 4: Tip mower back against the upper handle to gain
access to cutting blade. Remove foam shipping block
from cutting blade. This must be removed before starting
the engine.
LOWER
HANDLE
BRACKET
FIGURE 2
INSTRUCTION No. 7-3133 (REV 1, 2/12/01)
STEP 8: Driven disc to drive disc adjustment is set up at
the factory. In case driven disc may need adjustment,
proceed as follows:
C. Slide driven disc assembly over until 1/8” from
outside edge of drive disc. Maintaining the 1/8”
measurement, remove any looseness from the linkage.
This can be done by holding the transfer rod and
applying pressure to the left (as viewed from operators
position), then retighten the connector hex nut
securely. See Figure 9. Move shift rod to the number
one speed position, then back to the number six speed
position. Recheck the 1/8” measurement described
previously. Reinstall driven disc spring to driven disc
assembly.
A. Place speed control rod in the number six speed
position. See Figure 7.
SIXTH SPEED
POSITION
MOVE GROUND SPEED
CONTROL TO SIX SPEED
POSITION
1/8” MEASUREMENT
SIXTH
TO OUTSIDE EDGE
SLIDE DRIVEN
OF DRIVE DISC
DISC ASSEMBLY
TOWARD
FIRST SPEED
POSITION
DRIVE
OUTSIDE EDGE
DISC
FIRST
CONNECTOR
TRANSFER
ROD
OUTSIDE
EDGE
CONNECTOR
HEX NUT
FIGURE 7
B. Remove driven disc spring from driven disc
assembly as shown. Loosen connector hex-nut. See
Figure 8.
FIGURE 9
STEP 9: Make sure all nuts and bolts are tight. Set-up is
now complete for self-propelled models Proceed to the
pre-sale checklist page of this instruction to prepare
mower for use.
DRIVEN DISC
ASSEMBLY
DRIVE DISC
DRIVEN
DISC
SPRING
TRANSFER
CONNECTOR HEX
NUT
ROD
CONNECTOR
FIGURE 8
3
DEALER PRE SALE CHECKLIST for SNAPPER
21” STEEL DECK “M” MODEL WALK BEHIND MOWERS
The following must be accomplished prior to sale. Refer to the previous pages in this instruction for detailed
set-up instructions. Review this checklist with purchaser. Check (✓) items actually performed and signed on
checklist.
SET-UP CHECKLIST
_____ FOAM SHIPPING BLOCK removed from cutting blade.
_____ UPPER HANDLE & LOWER HANDLE secured in place and hardware tightened securely.
_____ SIDE CHUTE, RECYCLING COVER or GRASS BAG installed on mower.
_____ BLADE retaining bolt(s) checked and tighten securely.
LUBRICATION
_____ ENGINE OIL added to bring level up to full mark on 4-cycle engines (Refer to Engine Manual).
_____ DIFFERENTIAL grease checked and added if needed.
OPERATIONAL TEST
_____ ENGINE started, engine control settings checked and adjusted as needed.
_____ WHEEL DRIVE checked for proper operation and adjusted as needed (Self-Propelled Models).
_____ DRIVE DISC adjustment checked and made (Self-Propelled Models).
_____ GROUND SPEED control checked (Self-Propelled Models).
CPSC (Consumer Product Safety Commission) COMPLIANCE TEST
_____ BLADE CONTROL stops engine when released.
DEALER’S RECORDS & FINAL CHECK
_____ PERSONALLY HANDED Operator’s Manual & Mower Safety Booklet to purchaser.
_____ INSTRUCTED purchaser to read and follow instructions in Operator’s Manual.
_____ DEMONSTRATED proper starting procedure and operation of mower to purchaser.
_____ INSTRUCTED purchaser how to service air cleaner, maintain oil level (4-cycle).
_____ ASSISTED purchaser in completing Product Registration Card.
CONSUMER/OPERATOR PRODUCT REGISTRATION CARD
Purchase Date ___________________ Model _______________________ Serial No.________________________
Retailers Name ___________________________________ Signature _____________________________________
Address _____________________________________ City ____________________ State _______ Zip _______
MOWER WILL BE USED COMMERCIALLY? _______ YES _____ NO
Purchaser’s Name _________________________________ Signature ____________________________________
Address ____________________________________ City _____________________ State _______ Zip _______
IMPORTANT: This form is to be retained by the Dealer for future reference regarding Warranty, proof of
purchase, traceability for product recall or service, etc. Complete the Product Registration Card and Mail to
Customer Service Department at SNAPPER, P.O. BOX 1379, McDonough, Georgia, 30253.
INSTRUCTION No. 7-3133 (REV 1, 2/12/01)
4
|