MODEL GC-STC-CSV
THIS MANUALCONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FORYOUR SCAGACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEPYOURACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE, PLEASE READ ALL THE INFORMA-
TION ENCLOSED.
PART NUMBER 03183
Download from Www.Somanuals.com. All Manuals Search And Download.
A replacement manual is available from your
1.1 INTRODUCTION
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050. You may also contact
manual for this grass catcher can be downloaded by
using the model and serial number or use the contact
form to make your request. Please indicate the
complete model and serial number of your Scag
product when requesting replacement manuals.
This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this grass catcher. Read it carefully and
keep it for future reference.
The replacement of any part on this product by other
than the manufacturer's authorized replacement part
may adversely affect the performance, durability or
safety of this product.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
WARNING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer. Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacement parts.
2. Before dumping the debris, disengage the
mower, stop the engine and wait for all
movement to stop.
3. ALWAYS turn the engine OFF, remove the key
and wait for all movement to stop before
servicing or cleaning the mower or the grass
catcher.
When ordering parts, always provide the complete
model number of your catcher.
All information provided in this manual is based upon
information available at the time of printing. Scag
Power Equipment reserves the right to make changes
at any time without notice or obligation.
DANGER
ROTATING BLOWER
BLADES
1.2 DIRECTION REFERENCE
STOP ENGINE BEFORE
ENTERING CHUTE
The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.
CONTACT CAN INJURE
4. Do not modify or alter any component of the
grass catcher attachment or mower.
2.1 SAFETY AND OPERATING
INSTRUCTIONS
5. Do not allow any passengers to ride on the grass
catcher attachment or on the mower.
-NOTE-
To avoid personal injury, it is imperative that all
safety instructions be observed.
2.2 GRASS CATCHING OPERATION
1. Read this operator's manual and the operator's
manual that is supplied with the machine this
attachment is used on.
1. With the hopper door closed, engage the deck
drive.
2. Proceed to mow until the hopper is full.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. To clean the hopper debris screen;
3. When dumping the hopper into a disposal area:
A. Disengage the deck drive and allow all
moving parts to come to a complete stop.
WARNING
DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS
BURNING
B. Apply parking brake and shut off the engine.
A. Disengage the deck drive, apply the parking
brake and allow all moving parts to come to
a complete stop.
C. Stand on the left side of the hopper
assembly.
D. Unhook the debris screen latches and
remove the debris screen from the hopper.
See Figure 2-3.
B. Pull downward on the hopper door handle to
allow the hopper sweeper to remove the
material from inside the hopper. See Figure
2-1.
Debris Screen
Latches
Figure 2-3 GC-CS
FIGURE 2-3
FIGURE 2-1
E. Remove material from the debris screen and
reinstall. Secure by latching the debris
screen latches.
C. Once the material has been completely
removed from the hopper, lift the hopper
door handle to close the hopper door and
lock into place. See Figure 2-2.
6. When service is needed inside the hopper,
disengage the deck drive and allow all moving
parts to come to a complete stop, shut off the
engine and apply the parking brake. Rotate the
hopper door prop rod upward until it contacts the
hopper door. This will prevent the hopper door
from moving until the service is complete. See
Figure 2-4.
LOCK
FIGURE 2-2
Hopper Prop
Rod
4. When dumping the hopper into a disposal area,
inspect the hopper debris screen for material.
When the debris screen is full of material, the
grass catching ability may suffer. Frequency of
cleaning the hopper debris screen will vary
dependingonconditions.
Figure 2-4 GC-CS
FIGURE 2-4
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 ASSEMBLY INSTRUCTIONS FOR 48"
AND 52" CUTTER DECK
4. Install the grass catcher pulley onto the spindle
assembly. Apply loctite to both pulley setscrews
and tighten. See Figure 3-1.
-NOTE-
5. Remove the "Custom-Cut" and "Turbo" baffles
from the cutter deck. Using the original
hardware, install the new "Custom-Cut" and
"Turbo" baffles. See Figure 3-2.
Use the illustrated parts list as a part number
reference when following the assembly
instructions.
1. Remove all packaging materials. Lay out the
mounting hardware and the catcher assembly
parts for easy access. Prepare the work area
making sure that it is a clean, safe environment.
Front Baffle
48V - 424401
52V - 424402
Turbo Baffle
48V - 424210
52V - 424211
WARNING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
UNDER SIDE OF
VELOCITY-PLUS
CUTTER DECK SHOWN
2. Remove the discharge chute from the cutter
deck. See Figure 3-1.
FIGURE 3-2
-NOTE-
-NOTE-
Do not discard the discharge chute or
mounting hardware. The discharge chute
MUST be reinstalled anytime the grass
catcher has been removed from the machine.
Do not discard the original "Custom-Cut"
or "Turbo" baffles. These baffles may be
reinstalled anytime the grass catcher has
been removed from the machine.
6. Install the blower mounting bracket to the deck
using carriage bolts (p/n 04003-11), lockwashers,
and nuts. Do not fully tighten the hardware at
this time. See Figure 3-3.
3. Remove the right side belt cover to gain access
to the spindle assembly. Remove the front u-nut
from the cutter deck bracket. See Figure 3-1.
-NOTE-
Retain the original belt cover. This cover
MUST be reinstalled anytime the
complete catcher system is removed.
FLATWASHER
INSTALL PULLEY
ON RH SPINDLE SHAFT -
ON TOP OF EXISTING
SPINDLE DRIVE
REMOVE DISCHARGE
CHUTE AND
ELASTIC STOP
NUT
HARDWARE
PULLEY
REMOVE EXISTING
RT. SIDE BELT
COVER
CARRIAGE BOLT
REMOVE U-NUT
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
FIGURE 3-3
Figure 1- GC-STC-V install art
FIGURE 3-1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Install the hopper mounting brackets to the
outside of the frame on the rear of the machine.
See Figure 3-5.
7. Install the blower assembly to the mounting
bracket and secure with the mounting pin.
See Figure 3-4.
Hopper
Mounting
Brackets
8. Align the blower assembly with the discharge
opening of the cutter deck. Tighten the
hardware for the mounting bracket. See Figure
3-4.
Rear Frame
Figure
4
A
GC-STT Install Art
9. Install the quick pin through the rear hole in the
discharge chute mounting bracket. See Figure 3-
4.
BLOWER
ASSEMBLY
FIGURE 3-5
QUICK
PIN
13. With help from an assistant, install the hopper
assembly to the machine by installing the
mounting post into the hopper mounting brackets
and secure with the ring pins. Tighten the bolts
and jam nuts. See Figure 3-6.
HAIR
PIN
MOUNTING
BRACKET
MOUNTING PIN
TIGHTEN MOUNTING
BRACKET HARDWARE
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
2006 GC-STC-V install art 3
FIGURE 3-4
10. Install the belt to the spindle pulley. When
replacing the belt, see figure below.
PROPERYL
SECREVI
ENGEI
WTHI
OLI
AND
FUEL.
BACK SIDE
IDLER PULLEY
BLOWER
PULLEY
Locking
Bolts
Hair
Pin
Ring Pins
SPINDLE
PULLEY
Locking
Bolts
FRONT SIDE
IDLER PULLEY
Ring Pins
11. Install the new belt covers and secure. See
items number 1 and number 21 on page 10 of the
Blower Mounting Components section in the
Illustrated Parts List for proper installation.
FIGURE 3-6
4
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Install the hose from the blower assembly
adapter to the hopper hood and secure using the
6-1/2"clamps.
15. Using the weight support bar (p/n 451517) as a
guide,identifythefourcorrespondingmounting
holes, and the existing hardware that will need
to be removed in order to secure the weight
support bar to the front of the machine as
shown. See Figure 3-7.
16. Install one 7/16-14 x 1-3/4" hex head bolt into
each of the four mounting holes in the weight
support bar, and through the matching holes in
the caster support weldment. Secure this
assembly to the front of the machine using the
7/16- .5" x 1-1/4" x .083" flatwashers and the
7/16-14 elastic stop nuts. Torque hardware to
59 ft. lbs. See Figure 3-7.
FIGURE 3-7
17. Operate and test.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 GRASS CATCHER REMOVAL
INSTRUCTIONS
Loosen
Locking
Bolts
1. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
Remove
Mounting
Pins
Loosen
Locking
Bolts
Remove
Mounting
Pins
2. Remove the bag assemblies from the grass
catcher.
3. Remove the rubber strap holding the adapter to
the blower assembly and the large quick pin
securing the blower to the discharge mounting
bracket. See Figure 4-1.
2005 GC-STC removal art 2-A
FIGURE 4-2
6. With help from an assistant, remove the hopper
assembly.
4. Remove the belt, pin, hair pin and large quick pin
securing the blower assembly to the cutter deck
and remove the blower assembly. See Figure 4-
1.
WARNING
ADAPTER
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
BLOWER
ASSEMBLY
QUICK PIN
7. Re-install the side discharge chute to the opening
on the cutter deck. Replace the two outside
mounting bolts on the discharge chute with the
clevis pins (p/n 04064-15) and rue cotter pins
(p/n 04069-03). See Figure 4-3.
PIN & HAIR PIN
MOUNTING
BRACKET
8. Re-install the cutter deck belt cover.
DISCHARGE
CHUTE
RIGHT SIDE OF
CUTTER DECK SHOWN
2006 GC-STC-V removal art 1
(Note: Some parts not shown for viewing purposes.)
FIGURE 4-1
CLEVIS PIN
P/N 04064-15
5. Loosen the locking bolts and remove the two (2)
pins holding the hood assembly to the mounting
posts on the rear of the machine. See Figure
4-2.
CLEVIS PIN
P/N 04064-15
RUE COTTER PIN
P/N 04069-03
GC-STC-V removal art 3
FIGURE 4-3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS
HOURS
Break-In 8 20 40 100 200 500 Procedure
(First 10)
Comments
X
X
X
X
Check all hardware for tightness
Inspect hose and adapter
Check belt for proper alignment
Inspect fabric bags
X
X
X
X
X
*Check screen in hopper
Inspect hose and adapter
Inspect fabric bags
Remove debris from screen
Check condition of blower
*Apply grease to blower bearings
Check belt for proper alignment
See figure below
X
* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.
GREASE FITTING
ON BEARING HOUSING
GREASE FITTING
ON BEARING HOUSING
BEHIND PULLEY
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV 48" & 52" BLOWER HOUSING ASSEMBLY
9
10
11
12
8
48
49
4
1
2
14
11
50
13
9
11
7
10
47
10
14
44
27
14
11
12
15
43
16
42
41
14
17
26
39
40
18
25
34
15
17
19
20
3
28
21
41
5
38
22
23
17
35
27
24
14
46
R
D
O
T
A
B
A
T
N
S
IN
G
24
14
t
o
G
W
p
e
n
E
R
g
B
i
n
L
D
e
U
O
D
b
A
D
N
I
N
e
f
S
L
C
E
O
o
r
H
S
T
E
S
e
A
S
O
P
E
S
c
R
G
l
G
e
A
R
a
E
A
R
n
G
A
in
N
U
S
T
g
D
E
A
C
o
r
R
A
M
O
D
T
r
e
C
W
E
m
L
I
S
H
O
o
v
i
I
N
E
R
R
S
n
g
T
O
A
R
E
L
R
L
E
D
29
6
30
33
32
37
31
31
45
47
2005 GC V+ Blower Assembly
45
35 34
36
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV 48" & 52" BLOWER HOUSING ASSEMBLY
Ref.
No.
Part
Number
Ref.
No.
Part
Number
Description
Description
1
2
3
4
5
6
7
8
04067-07
481547
04019-02
04001-59
481377
482080
481428
483223
04024-02
04021-05
04041-07
43277
Pin, Ring 2-1/4" Long
Lanyard, Deck Height Pin
Nut, Serr. Flange 1/4-20
Bolt, Hex Head 1/4-20 x 1-1/4"
Decal, Blower
Decal, Rotating Blower
Grip, Blower Lever
Cap, Square
Nut, Push On 3/8 Thread
Lock Nut, 3/8-16
Flatwasher, 3/8-.391 x .938 x .105
Spacer
Pulley, Idler 4" Dia.
Nut, Elastic Stop 3/8-16
Lockwasher, 3/8-16
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
04019-04
Nut, Serr. Flange 3/8-16
04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8
483037
461931
04003-12
04063-06
461796
483034
04021-10
461930
Decal, Danger
Blower Housing Weldment
Bolt, Carr. 5/16-18 x 3/4" Gr. 5
Key, 1/4 x 1/4 x 1-1/2"
Fan Weldment
Bearing Assembly
9
Nut, Elastic Stop 5/16-18
Blower Housing Assembly, GC-STT
Cover, Blower Housing
Clamp, 8-5/8" Max Dia.
Hose, 8.00" Dia. x 53" Long
Pulley, 4-3/4" O.D. - 1" Bore
Set Screw, 5/16-18 x 3/8"
Frame, Blower Mount
Spring, Main Drive
Spacer
Nut, Serr. Flange 5/16-18
Adapter w/Strap
Receiver Weldment, Mounting Post
Hair Pin Cotter, .177 x 3-1/4"
Dust Shield
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
421319
48136-02
48135-09
482298
04012-04
461932
481522
43212
04019-03
461723
451821
483209
04021-09
04030-04
424361
04003-05
04001-54
04001-81
04001-21
461928
482379
483189
04043-04
43575
481039
Plate, Catcher Mounting
Bolt, Carr. 3/8-16 x 1-1/2"
Bolt, Hex Head 3/8-16 x 3" - 52"
Bolt, Hex Head 3/8-16 x 3-1/2"
Bolt, Hex Head 3/8-16 x 1-3/4"
Idler Arm Assembly
Belt, GC-STC
04062-04
424367
04066-04
Pulley, 3-1/2" O.D., GC-STC
Washer, 3/8 Hardened
Pivot, Idler
Quick Pin, 5/16" Dia.
Decal, Belt Cover
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV 48" & 52" BLOWER MOUNTING COMPONENTS
UNDER SIDE OF
VELOCITY-PLUS
CUTTER DECK SHOWN
16
16
10
10
11
5
23
2
26
27
23
25
4
6
7
28
1
24
26
8
3
25
25
6
24
13
9
12
21
14
15
15
22
20
16
18
17
19
RIGHT SIDE OF
CUTTER DECK SHOWN
2006 GC-STC-V BMC
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV 48" & 52" BLOWER MOUNTING COMPONENTS
Ref. Part
No.
Number
Description
1
483224
Belt Cover, GC-STC
2
3
04029-04
483223
Wingnut, Plastic 3/8" Small
Cap, Square Vinyl
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
04021-08
461723
Nut, Elastic Stop 1/4-20
Adapter, Blower GC-STC, includes item #7
Flatwasher, 1/4-.312 x .750 x .065
Rubber Strap 7-3/4"
Bolt, Hex Head 1/4-20 x 1-1/4"
Knob W/Stud, 3/8-16 x 1-1/4"
Clevis Pin, 5/16 x 1-1/2"
Pin, Rue Cotter 5/16 Dia.
Pin, Ring 1/2 x 2-1/4"
04040-14
48137-04
04001-59
481625-01
04064-15
04069-03
04067-07
481547
Lanyard
482587
Pulley, 4.0" Dia. 1.125 Bore
Setscrew, 5/16-18 x 3/8"
Nut, Elastic Stop 3/8-16
Lockwasher, 3/8"
Flatwasher, 3/8-.391 x .938 x .105
Bolt, Carr. 3/8-16 x 1-1/4" Grade 5
Mounting Post Weldment, Blower
Belt Cover, GC-STC-48V
Belt Cover, GC-STC-52V
U-Nut
Bolt, Carriage 3/8-16 x 1"
Bolt, Hex Head 5/16-18 x 1"
Flatwasher, 5/16-.375 x .875 x .083
Nut, Elastic Stop 5/16-18
Baffle, Front 48" Deck
04012-04
04021-09
04030-04
04041-07
04003-11
461894
424326
424327
22
23
24
25
26
27
04110-03
04003-23
04001-09
04040-15
04021-10
424401
424402
Baffle, Front 52" Deck
28
424210
Baffle, Turbo 48" Deck
424211
Baffle, Turbo 52" Deck
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV HOPPER COMPONENTS
16
14
49
50
5
4
3
45
45
41
15
31
11
43
51
17
56
55
40
58
59
8
12
9
25
29
6
33
37
34
10
53
2
50
49
34
B
49
42
24
55
27
43
49
6
53
61
48
60
36
18
38
63
19
53 C
49
34
12
49
50
52
20
54
41
49
66
65
49
18
24
49
53
53
60
7
67
A
61
62
58
33
59
28
1
49
64
21
10
34
38
32
49
69
30
49
45
49
63
38
35
46
22
49
37
13
33
36
25
49
57
49
21
C
23
33
26
38
58
32
53
40
44
49
20
65
B
59
53
64
66
46
33
19
A
65
61
68
29
46
26
58
59
60
57
28
49
49
61
68A
49
35
46
72
37
37
60
2006 CSHOPPEREXPLOD-STC
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV HOPPER COMPONENTS
Ref.
No.
Part
Number
Ref.
No.
Part
Number
Description
Description
1
2
3
4
5
6
7
8
461627
482732
461626
482777
04090-02
423834
423938
423849
423850
423858
423837
423840
451838
451601
451602
451603
451607
43631
423851
423852
422386
424405
424406
43063
43282
43277
481309
43641
43640
Hopper, GC-STC-CS
Door, GC-CS
Sweeper Weldment, GC-CS
Pad, Rubber
Pop Rivet, 3/16 x .652
Plate, Stiffener
Support Frame, Hopper
Hinge Bracket, L.H.
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
68A
69
04001-77
04003-04
04010-01
04017-16
04017-17
04019-03
04019-04
04020-12
04021-01
04021-09
04021-10
04032-01
04040-15
04041-07
43642
Bolt, Hex Head 3/8-16 x 3-1/2"
Bolt, Carriage 5/16-18 x 1"
Screw, #10-32 x 1/2"
Cap Screw, 5/16-18 x 3/4" Serr. Flan.
Cap Screw, 5/16-18 x 1" Serr. Flan.
Nut, 5/16-18 Serrated Flange
Nut, 3/8-16 Serrated Flange
Nut, 3/8-16 UNC Jam
Nut, #10-32 Elastic Stop
Nut, 3/8-16 Elastic Stop
Nut, 5/16-18 Elastic Stop
Washer, Special Wave
Washer, 5/16-.375 x .875 x .083 Flat
Washer, 3/8-.931 x .938 x .105 Flat
Bushing, Hopper Latch GC-CS
Bolt, Hex Head 3/8-16 x 3"
Hinge Weldment, Door
9
Hinge Bracket, R.H.
Bracket, Hopper Support
Latch, Door Prop
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Plate, Latch
Bellcrank Weldment, Upper
Debris Screen Weldment
Screen Support Weldment, Rear
Screen Support Weldment, Front
Hinge Weldment, Hopper
Spacer
Brace Stiffener, Short
Tube, Upright
Brace, Engine Mount
Latch, Dump Rod Inner
Latch, Dump Rod Outer
Spacer
Spacer
Spacer
Latch, Hood
Linkage Assembly, Lower
Linkage Assembly, Upper
Knob
Bolt, Hex Head 5/16-18 x 1-1/4
Bolt, Hex Head 3/8-16 x 3/4"
Bolt, Hex Head 3/8-16 x 1"
Bolt, Hex Head 3/8-16 x 1-1/2"
Bolt, Hex Head 3/8-16 x 1-3/4"
Bolt, Hex Head 3/8-16 x 1-1/4"
Bolt, Hex Head 3/8-16 x 2"
Bolt, Hex Head 3/8-16 x 2-1/4"
Bolt, Hex Head 5/16-18 x 3-1/2"
04001-54
451598
481547
481538
04020-26
481539
Lanyard
Rod End Male, 3/8-24 L.H. Thread
Nut, 3/8-24 UNF L.H. Thread
Rod End Male, 3/8-24 R.H. Thread
Nut, 3/8-24 UNF R.H. Thread
Alignment Bracket, GC-CS
Bolt, Hex Head 3/8-16 x 2-1/2"
Lock Wasker, 3/8-16 Spring
Nut, 3/8-16 UNC Zinc
Nut, 3/8-16 Center Lock
Retainer Strip, Hopper
Mounting Bracket Weldment, R.H.
Mounting Bracket Weldment, L.H.
Bracket, Lower Stiffener
04020-25
423865
04001-31
04030-04
04020-04
04021-05
423836
451726
451725
423855
423859
481245
04001-10
04001-18
04001-19
04001-20
04001-21
04001-32
04001-45
04001-46
04001-63
Backing Plate, Hopper (Not Shown)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GC-STC-CSV DECALS
481039
482275
483044
481327
481377
483037
483039
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY- COMMERCIAL ACCESSORY
AnypartoftheScagcommercialaccessorymanufacturedbyScagandfound,inthereasonablejudgmentofScag,
tobedefectiveinmaterialorworkmanship,willberepairedorreplacedbyanAuthorizedScagServiceDealerwithout
charge for parts and labor.
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of
returningitbacktotheownerafterrepairorreplacementwillbepaidforbytheowner. Scag’sresponsibilityinrespect
toclaimsislimitedtomakingtherequiredrepairsorreplacements,andnoclaimofbreachofwarrantyshallbecause
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service
Dealer.
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for
commercial purposes, or any other income-producing purpose including rental use.
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident, or
thathasbeenoperatedinanywaycontrarytotheoperating instructionsasspecifiedintheOperator'sManual. The
warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any
accessory or parts that have not been assembled or installed as specified in the Operator's Manual.
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or
durability. This warranty does not cover engines and electric starters, which are warranted separately by their
manufacturer.
ScagPowerEquipmentreservestherighttochangeorimprovethedesignofanyaccessorywithoutassumingany
obligation to modify any accessory previously manufactured.
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly
andexclusivelylimitedtotherepairorreplacementofdefectivepartsandScagdoesnotassumeorauthorizeanyone
toassumeanyotherobligationforthem. Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,
so the above limitation may not apply to you.
Scagassumesnoresponsibilityforincidental,consequentialorotherdamagesincluding,butnotlimitedto,expense
forgasoline,oil,expenseofdeliveringthemachinetoanAuthorizedScagServiceDealerandexpenseofreturning
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2005
PART NO. 03183
PRINTED 7-2005
PRINTED IN USA
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC
Download from Www.Somanuals.com. All Manuals Search And Download.
|