Owners Manual
Gebrauchsanweisung
Manuel du Propriétaire
Manual del Propietario
Handleiding
Manuale Instruzioni
MODEL 50, 60
Petrol Lawnmower
Motor-Rasenmäher
Tondeuse à Gazon à Essence
Cortadoras de Cesped a Gasolina
Benzine Grasmaaimachine
Falciatrice A Motore
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
1
4
B
A
A
2
5
3
6
i
Download from Www.Somanuals.com. All Manuals Search And Download.
7
8
9
12
1mm
13
14
A
10
15
11
16
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
ENGLISH
SAFETY INSTRUCTIONS
Safety Instructions
1. Training
a. Read the instructions carefully. Be familiar with the
controls and the proper use of the equipment.
b. Never allow children or people unfamiliar with these
instructions to use the mower. Local regulations may
restrict the age of the operator.
h. Do not mow excessively steep slopes.
i. Use extreme caution when reversing or pulling the
mower towards you.
j. Stop the blade(s) ,if the mower has to be tilted for
transportation when crossing surfaces other than grass
and when transporting the mower to and from the area
to be mowed.
c. Never mow while people, especially children, or pets
are nearby.
d. Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
k. Never operate the mower with defective guards or
shields, or without safety devices, for example deflectors
and/or grass catchers in place.
l. Do not change the engine governor settings or overspeed
the engine.
2. Preparation
m. Disengage all blade and drive clutches before starting
the engine.
n. Start the engine or switch on the mower carefully
according to instructions and with feet well away
from the blade(s).
a. While mowing, always wear substantial footwear and
long trousers.
Do not operate the equipment when barefoot or
wearing open sandals.
o. Do not tilt when starting the engine or switching on
the motor, unless the mower has to be tilted for
starting. In this case, do not tilt it more than absolutely
necessary and lift only the part which is away from the
operator.
b. Thoroughly inspect the area where the equipment is
to be used and remove all stones, sticks, wires,
bones and other foreign objects.
c. WARNING- Petrol is highly flammable.
p. Do not start the engine when standing in front of the
discharge chute.
q. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
r. Never pick up or carry a mower while the engine is
running.
s. Stop the engine and disconnect the spark plug lead:
i. Before clearing blockages or unclogging the chute.
ii. Before checking, cleaning or working on the mower.
iii. After striking a foreign object. Inspect the mower for
damage and make repairs before restarting and
operating the mower.
iv. If the mower starts to vibrate abnormally check
immediately.
t. Stop the engine
i. Whenever you leave the mower.
ii. Before refuelling.
u. Reduce the throttle setting during engine run-out and if
the engine is provided with a shut-off valve, turn off the
fuel at the conclusion of mowing.
Take the following precautions.
i. Store fuel in containers specially designed for this
purpose.
ii. Refuel outdoors only and do not smoke while
refuelling.
iii. Add fuel before starting the engine. Never remove
the cap of the fuel tank or add petrol while the engine
is running or when the engine is hot.
iv. If petrol is spilled, do not attempt to start the
engine but move the machine away from the area of
spillage and avoid creating any source of ignition
until petrol vapours have dissipated.
v. For reasons of safety the petrol tank and tank cap lock must be
replaced if damaged.
d. Replace faulty silencers.
e. Before using, always visually inspect to see that the
blades, blade bolts and cutter assembly are not worn or
damaged. Replace worn or damaged blades in sets to
preserve balance.
f. On multibladed machines, take care as rotating one
blade can cause other blades to rotate.
4. Maintenance and storage.
3. Operation
a. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
b. Never store the equipment with petrol in the tank inside
a building where fumes may reach an open flame or
spark.
c. Allow the engine to cool before storing in any enclosure.
d. To reduce the fire hazard, keep the engine, silencer,
battery compartment and petrol storage area free of
grass, leaves, or excessive grease.
e. Check the grass catcher frequently for wear or
deterioration.
a. Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
b. Mow only in daylight or in good artificial light.
c. Avoid operating the equipment in wet grass, where
feasible.
d. Always be sure of your footing on slopes.
e. Walk, never run.
f. For wheeled rotary machines, mow across the face of
slopes, never up and down.
g. Exercise extreme caution when changing direction on
slopes.
f. Replace worn or damaged parts for safety.
g. If the fuel tank has to be drained, do this outdoors.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
ENGLISH
1. SETTING UP
1.1 Grass catcher assembly
3. Press firmly down on the catcher top to lock the barbs into slots.
Figure 1.
1. Locate the catcher handle and align its front lugs with the slots
in the top of the catcher and press firmly into position. Figure 1.
2. Position the catcher top over the catcher bottom, aligning the barbs
on the top with the slots in the bottom. Figure 1.
4. Secure with two screws provided.
2. BEFORE OPERATING
2.1 Folding handles
CAUTION
l. Lockingknobs-Byturningtheseknobsthehandlebarscanbeeither
locked in the operating position or folded for storage.
2. Locking lever- Lift the lever to release the handle bars for folding
or push the lever closed to lock handle bars in the operating position.
Adjust the tension by turning the lock nut with a 1/2" AF
spanner.
Avoid premature engine failure by using a clean funnel
and clean away any possible contaminants.
2.4 Fuel
1. Position the mower on a level surface in a well ventilated area and
clean around the fuel tank cap.
2.2 Handle bar height
2. Using a clean funnel fill the fuel tank with unleaded petrol.
3. Replace the fuel tank cap and clean away any spilt petrol.
1. Loosen the two nuts (A) at the base of the handle bars on both sides
of the mower using a 1/2" AF spanner. Figure 2.
2. Move the handle bars to the required position and tighten the handle
bars nuts.
2.5 Controls
Throttle Control
Marked for O (off)
(slow)
(fast) positions. Figure 3.
2.3 Engine lubrication
Operator Presense Control
Handle moved towards the handle bars (I). Engine and blades are free to
rotate. Handle released (0) engine and blades stop rotating. Figure 4.
Self Propelled Drive Control
Moved towards 1 (on) turns the clutch on and drives the mower forward.
Moved towards O (off) turns the clutch off and stops the mower driving.
Figure 5.
Theengineoillevelmustbecheckedbeforeattemptingtostarttheengine.
Refer to the engine manufacturer's instructions.
1. Position the mower on a level surface and clean around the dip stick
or oil plug.
2. Remove the dip stick or oil plug.
3. Using a clean funnel slowly add oil in accordance with the engine
manufacturer's instructions.
Powerstart
Turnthekeytoon(I)positiontoengagetheelectricstarter.releasethekey
when the engine starts and allow to return to the off (0) position. Figure
16.
4. Check the oil level by screwing in the dip stick or oil plug and
removing again. When oil level is correct replace the dip stick.
3. OPERATION
3.1 Grass catcher
CAUTION
Installing the grass catcher
With powerstart mowers if the engine fails to start after 3
seconds of continuous cranking release the ignition key and
wait10secondsbeforetryingtorestarttheengine. Iftheengine
still fails to start check the fuel level, battery connections, and
battery condition. If the engine is cranking slowly the battery
may need charging, refer to section 6.3 for battery charging.
1. Raise the rear flap of the mower.
2. Grasp the grass catcher by the top handle and position the grass
catcher against the rear of the mower. Figure 6.
3. Lower the rear flap so that the back edge of the flap hooks over the
grass catcher.
Removing the grass catcher
3.4 To stop the engine
1. Move the throttle control lever to the stop position. O
2. Release the “Operator presence control handle”.
3. Turn the fuel tap off where fitted.
1. Grasp the grass catcher top handle and lift up.
2. Raise the rear flap of the mower to release grass catcher.
3. Lift the grass catcher clear of the mower and lower the rear flap.
4. Remove the ignition key on Powerstart mowers.
3.2 Adjusting the height of cut
3.5 Drive engagement - Self propelled mowers
1. Grasp the height of cut lever (A) and apply an outward pressure to
release the lever from the rack (B). Figure 7.
2. Move the lever while holding out to the required height of cut
position and engage the lever in the rack by releasing the lever.
1. Starttheengineandsettheenginespeedtotherequiredgrasscutting
speed.
2. Push forward on the clutch engagement lever to engage the self-
propelled drive to the rear wheels. Fig. 5.
3. To disengage the self-propelled drive release the engagement
lever and allow it to return to the disengaged position.
3.3 To start the engine
CAUTION
1. Move the Throttle Control lever to the fast position.
2. Press the primer bulb firmly 5 times.
3. Grasp the 'Operator presence control handle' and hold against the
handle bars. Refer engine manufacturers instructions. Fig. 4.
4. Grasp the starter handle and pull, or turn the ignition key on
Powerstart mowers.
Do not hold the engagement lever in a semi-engaged position to
slip the clutch as this will lead to excessive clutch wear.
3.6 Blade Brake Control
5. After engine starts, move the Throttle Control to the slow position.
The mower engine is fitted with a blade brake system. When the
“Operator Presence Control” is held against the handle bars the brake is
off (0). When the Operator presence control is released the blade brake is
on (I).
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
ENGLISH
4. MAINTENANCE GENERAL
CAUTION
4.1 Engine air cleaner
Do not over tighten the spark plug as engine damage may occur.
Refer to the engine manufacture's instructions for detailed cleaning
instructions.
The engine air cleaner element must be serviced after each 25 hours of
normal mowing. The element must be serviced more regularly if the
mower is used in dusty conditions.
4.4 Cutting assembly
1. Disconnect the spark plug lead.
2. Move the height of cut lever to the high cut position, and fold the
handle bars.
4.2 Snorkel air intake
3. Tilt the mower so that the spark plug is up.
4. Inspect the cutting assembly for damage and wear.
5. Check the disc retaining bolts. Tighten the centre bolt to 48 Nm.and
the three concentric bolts to 14 Nm.
The snorkel air cleaner element must be serviced after each 50 hours of
normal mowing. The element must be serviced more regularly if the
mower is used in dusty conditions.
6. Return mower to its normal position and replace the spark plug lead.
1. Disconnect the air tube from the element holder.
2. Remove the holder cap.
WARNING
3. Remove the cartridge and tap gently on a flat surface to remove dirt.
4. Replace element in holder and replace holder cap.
5. Replace the air tube to the bottom of the element holder.
Remove the spark plug lead before working on cutting assembly.
Do not work on the cutting assembly without wearing gloves.
4.5 Blade change
NOTE: Quantum engines fitted with a Remote snorkel air
intake are not fitted with an air cleaner element. Note the
air cleaner element on this model is located on the engine.
1. Disconnect the spark plug lead.
2. Set the mower to the high cut position.
3. Lift the rear flap on rear catcher mowers and prop open the flap to
give access to the blades.
Tilt utility mowers so that the spark plug is up.
4. Remove the blade, blade retaining bolts, nuts and washers and
discard. Retain only the ‘D’ plates.
CAUTION
Do not allow dirt to enter the air tube, engine damage may occur.
Check the condition of the air tube regularly and replace if
damaged.
5. Fit new blades, blade bolts, washers, and nuts in sets to maintain
balance. Figure 8.
6. Tighten the blade nuts to 16 NM. Check the blades are free to move
when the blade nut is tensioned.
4.3 Spark plug
7. Remove the flap prop or lower the mower to the ground and replace
the spark plug lead.
For best results remove and check the condition of the spark plug every
25 hours of use.
4.6 Throttle control
1. Stop the engine and remove the spark plug lead.
Each 25 hours of mowing use a small amount of light oil to lubricate
the throttle control lever.
2. Clean dirt from around the spark plug and remove the spark plug.
3. If a new spark plug is required use a Champion RJ19LM or
equivalent and set the electrode gap at 0.7 to 0.8 mm.
4. Screw the spark plug into the engine and tighten to 20NM.
5. MAINTENANCE - Self propelled mowers
5.3 Rear drive chain inspection
5.1 Drive chain lubrication
1. Remove the spark plug lead.
1. Remove the spark plug lead.
2. Remove the cover plate screws (a) and lift off the cover plate (b).
Figure 9.
2. Remove the drive shaft cover plate retaining screws (a) and remove
cover plate (b). Figure 11.
3. Support the rear wheels off the ground to enable the drive to be
rotated.
3. Remove the stone guard retaining screws (c) and remove the stone
guard. Figure 11.
4. Use SAE 30 oil and lubricate the drive chains at point (a) whilst
the chain is being rotated. Figure 10.
4. Remove the chain guard nuts (d) and slide the chain guard out of the
way. Figure 12.
5. Replace the chain cover plate and secure.
6. Replace the spark plug lead.
5. Inspectthedrivechainandaxlesprocketandreplaceiffoundtohave
excessive wear.
6. Replace the stone guard and drive shaft axle plate.
7. Replace the spark plug lead.
5.2 Drive chain adjustment
Front drive chain
1. Remove the spark plug lead.
2. Remove the cover plate.
5.4 Clutch adjustment
3. Loosen the chain tensioner bolt (b) and move the chain tensioner to
give a 3 mm deflection on the drive chain. Figure 10.
4. Tighten the chain tensioner bolt and rotate the drive wheels to check
the drive chain for tight spots.
1. Remove the spark plug lead.
2. Loosen the locknut (a) and turn the adjuster (b) clockwise until the
clutch is felt to drag. Figure 13.
3. Back off the adjuster anti-clockwise 2-3 turns and retighten locknut
(a).
5. Replace the cover plate.
4. Replace the spark plug lead.
Rear drive chain
1. Remove the spark plug lead.
2. Loosen the rear drive chain tension nut (c) and slide it upwards to
tighten the rear drive chain. Figure 9.
3. Retighten the rear drive chain tensioner nut and rotate the rear drive
wheels to check for tight spots.
4. Replace the spark plug lead.
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
ENGLISH
5. MAINTENANCE - Self propelled mowers
n
r
5.5 Clutch lining inspection
5. Lubricate the slot at the centre of the drive pinion (d). Figure 15.
6. Replace the wheel plug and wheel cap.
7. Replace the spark plug lead.
1. Remove the spark plug lead.
2. Remove the cover plate as explained in section 5.1 “Drive chain
lubrication”.
o
3. Check the thickness of the friction material. Figure 13. If thickness
of the friction material is less than 1mm the clutch plate should be
replaced by an authorised Rover Mowers Limited Dealer.
5.7 Drive wheel cleaning
1. Remove the spark plug lead.
2. Support the rear wheels off the ground and remove the wheel cap.
3. Remove the ratchet plate (c) retaining the wheel to the axle.
Figure 15.
5.6 Drive pawl lubrication
r
4. Remove the wheel from the axle and clean the inside of the wheel
hub.
5. Replace the wheel and retain using a new ratchet plate.
6. Replace the wheel plug and wheel cap.
7. Replace the spark plug lead.
1. Remove the spark plug lead.
2. Support the rear wheels off the ground.
3. Remove the rear drive wheel cap (a) and the wheel plug (b). Figure
c
14.
o
u
4. Rotate the drive wheel to align the drive pinion with the wheel plug
hole.
g
n
6. MAINTENANCE - Powerstart Mowers
6.1 Battery removal
c
1. Remove the two retaining screws from each side of the battery
support box and remove the front cover.
2. Remove the battery from the support box and simultaneously
disconnect the wiring loom from the battery terminals.
2. Connect the battery charger to a suitable mains
power outlet and switch on.
3. Whenchargingiscompleteafter10to16hours,switchoffthepower
outlet and disconnect the battery charger from the power outlet.
4. Disconnect the battery charger leads from the battery and refit the
battery to the mower.
o
o
n
6.2 Battery installation
1. Connect the mower wiring loom to the battery with the red lead
attached to the positive (+) terminal of the battery and the black lead
to the negative (-) terminal of the battery.
2. Fit the two rubber blocks to each end of the battery and place the
battery complete with the rubber blocks into the battery support box
with the battery terminals closest to the centre of the mower.
3. Refit the battery support box front cover and retain with the two
screws.
6.4 Care and handling
d
d
t
1. Do not disassemble the battery, as it’s strong acid electrolyte may
burn your skin or clothes.
2. Do not short out the battery terminals, as this may burn the terminals
and cause damage to the equipment.
3. Do not incinerate the battery to depose of them.
The battery may explode if exposed to fire.
4. Cleanthebatterywithadrycloth only, never useoil, petrol, thinners
or any other petrochemical.
6.3 Battery charging
A new battery when supplied with the mower may not be fully
charged to maximum capacity. The battery should have an initial
charging period of 10 to 16 hours. To charge the battery it must be
removed from the mower first.
5. Handle the battery with care. If the battery is dropped and the case
is damaged the acid electrolyte (sulphuric acid) may leak out. Wipe
up leaking acid with a cloth and neutralise acid with an alkaline
solution.
6. In the event of electrolyte coming into contact with the skin,
immediately flush with water and seek medical attention.
o
m u
CAUTION
Use only an approved battery charger supplied by the mower
dealer which has been designed for use with this battery.
e
n
u
t
1. Connect the battery charger to the battery with the
red lead (positive) to the positive (+) terminal of the
battery and the black (negative) lead to the negative
(-) terminal of the battery.
n
m o
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
7. SPARE PARTS
26
7.1 Series 85000, 86000 and 96000 base spare parts
1
2
3
4
5
6
7
8
A03300
A03510
A03456
A03325
A03455
A03126
A10148
A02591
A03515
A03514
A03516
A02051
A01486
A00293
A01716
A03830
A03930
A00673
A10154
A10140
A10527
A03450
A03459
A03320
A03353
A03414
A03306
A03743
Base
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
4
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
46
47
48
49
50
51
52
53
A03492
A03409
373109
A03092
S2501116
290112
A02127
*
A04052
A03549
A03323
A010141
A03313
A03250
A10284
A03336
A02066
A03319
A03303
A10381
A03604
A02071
A02235
A03472
A03927
A04108
A04099
A04111
Decal- sound level
Nameplate
Tension washer
Ratchet plate
Ratchet plate
Poprivet- 73 AS 6-4 blind
Taptite- 3/8" - 16 HWH x 1" Ind.hex.W/H Duo.
Decal- Model
Self tapping screw- 10 x 5/8" pan ph/head2
1
1
4
4
2
Height adjustment rack
Rear Flap
Spring- rear flap
Handle- rear flap
Pivot bush
Conbar assembly
Conbar spring
Axle bracket- RH.
Axle bracket- LH.
Clamp bolt
Woodruff key
Disc boss
Disc assembly
Backplate
Blade- standard
Blade- Mulch N Catch
Blade bolt kit
10
3
1
9
10
11
12
13
14
15
16
16
17
18
19
19
20
21
22
23
24
25
26
Cable clip
1
1
1
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
2
Plug chain slot- model 50
Rear axle assembly- model 50
Rear axle bush- model 50
Plastic handle
Height adj. lever assembly
Packing plate
Rivet
Rear wheel assembly
Grass deflector
Rear stoneguard- Mod. 50
Rear stoneguard- Mod. 60
Rivet- 73 SS 4-3
Nyloc nut- 1/4" unc.
Decal- turbothrust
Nose comb
2
1
1
1
2
4
2
8
4
1
1
Disc bolt kit
Front axle assembly- professional
Front axle assembly- professional
Front axle bush
Wheel seal
Front wheel assembly
Wheel bearing
Wheel cap
Rivet
Pivot rod
Decal- Warning
Washer- 3/16" x 3/4"
Screw
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
7. SPARE PARTS
7.2 Handle bar spare parts
1
2
3
3
4
5
6
7
8
9
A03802 Handle bar-
14
15
A04045 Flanged nut- 5/16" unc.
A02223 Nyloc nut- 5/16" unc.
A03317 Lower handle bar
A03583 Throttle cable- Mod. 50
A03326 Throttle cable- Mod. 60
A10016 Throttle control assembly
A02849 Lock handle
A03307 Draw bolt
A03500 Cable clip
A03518 Plug spanner
A10144 Grass catcher assembly
16 A10523 Bale assembly CE
17 A10524 Bale assembly CE
18 A10503 Handle assembly CE
19 A03739 Handle grip CE
20 A02521 Spacer CE
21 A03722 Brake cable- mod. 50,60
22 A03733 Rope stop CE
23 A02235 Nyloc nut- 1/4" unc.
10 A03324 Mesh
11 A03447 Handle
24 A04083 Screw - 10 x 19mm Pan Head
25
12
13
A02260 Roll pin- 1/4" x 3/4"
A02028 Setscrew- 5/16" x 5/8" unc.W/Face.
26
27 A03622 Decal
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
7. SPARE PARTS
n
.
.
n
.
.
.
.
.
.
.
7.3 Self propell
. e
48
49
50
A02078
A02081
A02235
Setscrew- 1/4" x 1/2" unc.hex
Setscrew- 1/4" x 1-3/4" unc.hex
Nyloc nut- 1/4" unc.
1
2
3
4
5
6
7
7
8
A02102
A10177
A03365
A07822
A03314
A03391
A03383
A10381
A03393
A02090
A03373
A03371
A03372
A03361
A07675
A10172
A03366
A03394
A02069
A03368
A03382
A03353
A03352
A03441
Washer- Avdel 7601/0010
Clutch lever
Clutch cable
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
A03414
A03369
A03377
A03364
A03367
A03360
A10171
A03358
A10170
A03359
A03550
A03363
A03370
A04052
A03552
A03551
A03386
A02070
A03354
A03376
A03375
A03250
A02146
A02214
Wheel cap
Drive shaft
Rear drive chain
Cable support bracket- RH
Chain tensioner
51 S2491162 Nut- 1/4" unc.square pressed
Cable tie
52
53
54
55
56
A02001
A03092
A02030
A02209
A02044
Nut- 1/4" unc.hex
Rear axle support
Stoneguard mount bracket
Rear stoneguard- 96012
Rear stoneguard- 86012, 86040
Drive shaft cover
Circlip- 1400/12
Pawl retainer washer
Drive pinion- RH
Pawl
Bearing- 6001 DDU
Nylon bush
Rear axle assembly
Rear chain guard
Felt seal
Roll pin- 1/8" x 3/4"
Rear drive shaft sprocket
Dust seal
Wheel bearing
Geared wheel hub
Washer plate
Washer- Avdel 7301/0016
Washer- 5/16" x 5/8" x 18g.flat
Washer- 1/4" x 5/8" x 18g.flat
Washer- 1/4" internal shakeproof
Tension washer
Clutch engagement bush
Driver clutch plate
Clutch spring
Driven clutch plate
Clutch support shaft
Drive chain housing- LH
Cable support bracket- LH
Drive pinion- LH
Self tapping screw- 10 x 5/8" pan ph/head
Chain guard cover plate
Drive chain housing- RH
Felt seal
Roll pin- 3/16" x 7/8"
Sprocket PTO.
57 S373109
58 A10146
59 S2501108 Washer- Avdel 7301/0008
60
61
62
9
Wheel assembly
e
10
11
12
13
14
15
16
17
18
19
20
21
22
23
A10284
A02118
A03336
Height adjustment lever assembly
Rivet- 3/4" x 1/4" flat head
Plate
n
63 S3521047 Wheel plug
64
65
66
67
68
69
70
71
72
A03470
290112
A03390
A03384
A10524
A10503
A03739
A02521
A03604
Chain guide
Rivet- 73 AS 6-4 blind
Clutch plate lining
Tyre
Bale assembly CE
Handle assembly CE
Handle grip CE
Spacer CE
l
Front drive chain
Pivot rod
Handle
Setscrew- 1/4" x 3/4" unc.hex
Setscrew- 1/4" x 5/8" unc.hex
m
Rear extension- Mod. 60
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
7. SPARE PARTS
7.4 Powerstart spare parts - Series 85000, 86000
19 A03610
20
Foam block
1
2
3
4
5
6
7
8
9
A03802
A10016
A03581
A03557
A03560
A07679
A03741
A03565
A03559
Upper handle bars-Mod 60
Throttle control assembly
Throttle cable- Quantum
Key start housing
21 A10524
22 A10503
23 A02521
24 A03739
25 A03732
26 A03733
27
Bale assembly- Mod 60 CE
Handle assembly Mod.60- CE
Spacer
Key start switch
Handle grip- CE
Ignition key
Cable clip- CE
Wiring loom- Mod 60 CE
Cable clamp
Rope stop- CE
Battery
28 A02235
29 A04083
30
30 A03722
31 A03756
Nyloc nut- 1/4" unc.
Screw- 10 x 3/4 pan head
10 A03558
11 A03556
12 A03563
13 A02083
14
15
16
17
18
Battery block
Battery support box
Decal- caution
Brake cable- mod. 60
Switch Plate
Setscrew- 5/16" x 3/4" unc.hex.
Washer- 5/16" x 7/8" x 18g.flat
Nyloc nut- 5/16" unc.
Speed nut- 3/16" bsw.
Screw- 3/16" x 1/2" mush/head
Rivet- 73 AS 5-2
A02012
A02223
A02002
A02163
A04060
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rover Mowers Limited
GB Read the instructions carefully
D
F
Lesen sie die hinweise sorgfaltig
Lisenlesinstructionsattentivement
SP Lea las instrucciones con mucho
cuidado
NL Lees de gebruiksaanwijzing
zorgruldig
I
Leggere attentamente le istruzioni
GB Caution
GB Rotating cutting blades
D
F
Achtung
Attention
D
F
Rotierende messer
Lames de coup rotatives
SP Atencion
SP Lame in movimento
NL Draaiende Snijmessen
NL Voorzichtig
I
Attenzione!
I
Lama con taglio a rotazione
GB Keep bystanders away
D
F
Andere fernhalten
Restez a l'ecart du public
SP Mantenga alos espectadores le jos de ustad
NL Houd toeschouwer op afstand
I
Tenere lontano le persone circostanti
GB Stop the engine and disconnect the spark plug lead before checking,
cleaning or working on the mower
D
Den motor abstellen und das Zundkerzenkabel von der Zundkerze
abziehen vor arbeiten am Maher
F
Arretez le moteur et debranchez la bougie avant de verifer, nettoyer ou
reparer la tondeuse
SP Pare el motor y desconecte el cable de la bujf a antes de comprobar,
limpiar o examinar la cortadora
NL Stop de motor en trek de bougieleabel los voor het inspecteren,
schoonmaken of reparen van de maaimachine
I
Fermareilmotoreestaccareilcavettodallacandelaprimadicontrollare,
pulire o aggiustare la tosaerba
GB Powerstart
Turn the key to the (I) position to engage the electric starter, release the
key when the engine starts and allow to return to (O) position
Powerstart Kontrollen
D
F
Zundschlüssel auf Stelle an (I) drehen, um den Anlasser einzuschalten.
Beim Anspringen des Motors den Schlück lassen
Contrôles de démarrage électrique
Tournez la clé sur la position (I) pour engager le démarrage électrique.
Relâchez la clé quand le moteur démarre et laissez retourner à la
position (O)
SP Powerstart Control
Mover la llave hacia (I) las posicion para atracer el arranque electrico.
Dispara la llave cuando el motor empieza a dejar a regresar al (O)
posicion apagdo
NL Regulatuur bij Powerstart machines
Draai de startsleutel in postie no. (I) em de electrische starter in te
schaken. Laat de startsleutel los als de motor loopt en laat hem
in de (O) teruggaan
I
Controlli messa in moto
Girare la chiave posizione (I) per accendere il motorino elettrico
d'avviamento. Lasciare libera la chiave quando il motore e in moto, in
modo che ritorni in posizione (O)
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
RoverMowersLimited
GB Self propelled drive control
Moved towards (I) turns the clutch on and drives the mower forward.
Moved towards (O) turns the clutch off and stops the mower
driving
D
F
Selbetantriebbetätgung
Einstellung auf (I) aktiviert die Kupplung und den Motor vorwärs.
Einstellung auf (I) schaltet die kupplung aus und bringt den Mäher zum
Stehen
Contrôle d'autotraction
Déplacé vers (I) enclenche l'embrayage et fait avancer la tondeuse.
Déplacévers(O)décengagel'embrayageelempéchelatondeused'avancer
SP Autopropulsado marcas del control
Movidohacia(I)mueveeldesembragadoryponeamarchaelcortacesped.
Movido hacia el (O) apaga el desembragador y para el cortacesped
NL Regulatuur bij relfverplaatsende machines
Als men de knop op (I) zet, is de koppeling ingeschakeld en de machine
rijdt vooruit. Alsdeknop(O)zet,schakeltmendeknoppelinguiten
demachinestopt.
I Camandotrazioneremovente
SemossoversoI(innestato)innestalafrizioneemuoveinavantila
faiciatricetosaerba.SemossoversoO(disinnestato)disinnestala
frizioneefermalatrazionedellafalciatricetosaerba
GB Operator presense control
Handle moved towards the handle bars, engine and blades are free to
rotate. Handle released, engine and blades stop rotating
Bedieneranwesenheitakontrolle
Giff in Richtung Giffbügel vorgestzt, motor und messer rotieren frei,
Griff gelôst, Motor und messer stoppen
Contrôle par opérateur
D
F
Poigée avancée vers les mancherons, moteur et lames peuvent tourner.
Poignée relâchée, moteur arrêtent de tourner
SP Operador de las presencias controles
Mango movido hacia manillas, motor y cuchillas estanlibres de hacer
vucltas. Mango disparado, motor y cuchillas paran de hacer vucltas
NL Dodenmanskoop regulatuurknop die aangeeft dat de oparateur
aanwezig is
De gasbedieningshendel geplaast in de richting van de hand grepen,
de machine loopt en de messen draaien vrij. Gasbedieningshendel is
afgezet, de machine stopt, en de messen draaicn neit meer
I
Comando presenza operatore
(I) Manopola mossa verso barre manubrio, motere e lame in posizione
libers e rptanti. (O) manopola disimpegnata. Motre e lame fermi
GB Throttle control
Marked for off, slow and fast positions
Gasbedienung
D
F
Markierung aus, langsam sch schnell
Contrôle des gaz
Marque pour les positions arrêt, ralenti accéléré et
SP Control del accelerador
Marcado por apagado, despacio, rapido posiciones
NL Gasknop regulatuur
Voorzien van markteken uit, langzaam, snel tekening
Comande
I
Segno di poizione O staccato lento veloce
PAGE11
Download from Www.Somanuals.com. All Manuals Search And Download.
For your record:
Para su referencia:
Dealer .................................................
Date of Purchase ....................................
Model .................................................
Serial No..............................................
Vendedor .............................................
Fecha de compra ....................................
Modelo ................................................
Serie no ...............................................
Für lhre Aufzeichnung:
Voor uw informatie:
Händler ...............................................
Lieferdatum ..........................................
Modell Nr ............................................
Seriennummer .......................................
Handelaar.............................................
Aankoopdatum.......................................
Type ...................................................
Serienummer.........................................
Pour votre information personnelle:
Dati da registrare:
Fabricant..............................................
Date d'achat..........................................
Modèle ................................................
NO de série ...........................................
Distributore ..........................................
Data d'acquito .......................................
Modello ...............................................
N.o Serie .............................................
These machines are covered by one or more of the following Registered Designs and or Patents;
Registered Designs: Australia. 131504, 134850
Patents: Australia. 713852, 745750, New Zealand. 330293, US. 6085508, UK. GR2325139
ACN 000 257 303
Head Office and Factory: Rover Mowers Limited
155 Fison Avenue West, Eagle Farm, 4009
Brisbane, Queensland, Australia.
Recycled paper
GWAIL
04003632- CE
Revision I.
PRINTEDINAUSTRALIA
Copyright1/2003
©
Download from Www.Somanuals.com. All Manuals Search And Download.
|