MODEL SCR
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG MOWER. READING
THIS MANUAL CAN PROVIDE YOU WITH
ASSISTANCE IN MAINTENANCE AND AD-
JUSTMENT PROCEDURES TO KEEP YOUR
MOWER PERFORMING TO MAXIMUM EFFI-
CIENCY. THE SPECIFIC MODELS THATTHIS
BOOK COVERS ARE CONTAINED ON THE
INSIDE COVER. BEFORE OPERATINGYOUR
MACHINE, PLEASE READ ALL THE INFOR-
MATION ENCLOSED.
PART NUMBER 03103
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
GENERAL INFORMATION
For pictorial clarity, some illustrations and figures in this
1.1 INTRODUCTION
manual may show shields, guards or plates open or
removed. Under no circumstances should your mower
be operated without these devices in place.
Your mower was built to the highest standards in the
industry. However, the prolonged life and maximum
efficiency of your mower depends on you following the
operating, maintenance and adjustment instructions in
this manual.
All information is based upon product information
available at the time of approval for printing. Scag
Power Equipment reserves the right to make changes
at any time without notice and without incurring any
obligation.
If additional information or service is needed, contact
your Scag Power Equipment Dealer.
1.2 DIRECTION REFERENCE
We encourage you to contact your dealer for repairs. All
Scag dealers are informed of the latest methods to
service this equipment and provide prompt and efficient
service in the field or at their service shop. They carry a
full line of Scag service parts.
The “Right” and “Left”, “Front” and “Rear” of the
machine are referenced from the operator’s right and left
when seated in the normal operating position and facing
the forward travel direction.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
1.3 SERVICING THE ENGINE AND DRIVE
TRAIN COMPONENTS
When ordering parts, always give the model and serial
number of your tractor. The serial number plate is
located where shown in Figure 1-1.
The detail servicing and repair of the engine, hydraulic
pumps and gearboxes are not covered in this manual;
only routine maintenance and general service
instructions are provided. For service of these
components during the limited warranty period, it is
important to contact your Scag dealer or find a local
authorized servicing agent of the component
manufacturer. Any unauthorized work done on these
components during the warranty period may void your
warranty.
Serial Plate
SCR 2K SPL
Figure 1-1Tractor Serial Number Plate Location
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ISO Symbols
CE Mark
SYMBOL
DESCRIPTION
SYMBOL
DESCRIPTION
Choke
Transmission
Parking Brake
Spinning Blade
48071S
On/Start
Off/Stop
Spring Tension on Idler
Oil
Falling Hazard
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOL
DESCRIPTION
SYMBOL
DESCRIPTION
Fast
Slow
Cutting element - Basic symbol
Continuously variable - Linear
Pinch Point
Cutting element - Engage
481039S
Hourmeter/elapsed operating hours
Cutting element - Disengage
Keep bystanders away
Read operator's manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
SAFETY INFORMATION
2.1 INTRODUCTION
Your mower is only as safe as the operator. Carelessness
or operator error may result in serious bodily injury or
death. Hazard control and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of the personnel involved in the operation,
transport, maintenance and storage of the equipment. Make
sure every operator is properly trained and thoroughly
familiar with all of the controls before operating the mower.
The signal word “DANGER” denotes that an extremely
hazardous situation exists on or near the machine that could
result in high probability of death or irrepairable injury if
proper precautions are not taken.
WARNING:
The signal word “WARNING” denotes a hazard exists on
or near the machine that can result in injury or death if
proper precautions are not taken.
READ THIS OPERATOR’S MANUAL BEFORE
ATTEMPTING TO START YOUR MOWER.
A replacement manual is available from your authorized
Scag Service Dealer or by Contacting Scag Power
Equipment, Service Department at P.O. Box 152, Mayville,
WI 53050. Please indicate the complete model and serial
number of your Scag product.
CAUTION:
The signal word “CAUTION” is a reminder of safety
practices on or near the machine that could result in
personal injury if proper precautions are not taken.
2.2 SIGNAL WORDS
Your safety and the safety of others depends significantly
upon your knowledge and understanding of all correct
operating practices and procedures of this machine.
2.3 BEFORE OPERATION
CONSIDERATIONS
1. NEVER allow children to operate this riding mower.
Do not allow adults to operate this machine without
proper instructions.
This symbol means “Attention! Become Alert! Your
Safety is Involved!" The symbol is used with the following
signal words to attract your attention to safety messages
found on the decals and throughout this manual. The
message that follows the symbol contains important
information about safety. To avoid injury and possible
death, carefully read the message! Be sure to fully
understand the causes of possible injury or death.
2. DO NOT mow when children and/or others are
present.
3. Clear the area to be mowed of objects that could be
picked up and thrown by the cutter blades.
Signal Word:
4. DO NOT carry passengers.
It is a distinctive word on safety decals and throughout
this manual that alerts the viewer to the existence and
relative degree of the hazard.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
5. DO NOT wear loose fitting clothing that could get
tangled in moving parts. Do not operate the machine
wearing shorts; always wear adequate protective
clothing including long pants. Wearing safety glasses,
safety shoes and a helmet is advisable and is required
by some local ordinances and insurance regulations.
12. Equipment must comply with the latest requirements
per ANSI J137 and/or ANSI S279 when driven on
public roads.
-NOTE-
If the mower is driven on public roads, it must
comply with state and local ordinances as well as
SAE J137 and/or ANSI / ASAE S279 requirements.
Contact your local authorities for regulations and
equipment requirements.
6. Operator hearing protection is recommended,
particularly for continuous operation of the mower.
Wear suitable hearing protection. Prolonged exposure
to loud noise can cause hearing impairment or loss.
13. DO NOT operate without a chute deflector installed;
keep the deflector in lowest possible position.
7. Keep the machine and attachments in good operating
condition. Keep all shields and safety devices in place.
If a shield, safety device or decal is defective or
damaged, repair or replace it before operating the
machine.
14. Check the blade mounting bolts at frequent intervals
for proper tightness.
15. Make sure all hydraulic fluid connections are tight and
all hydraulic hoses and lines are in good condition
before starting the machine.
WARNING:
This machine is equipped with an interlock system
intended to protect the operator and others from
injury. This is accomplished by preventing the
engine from starting unless the operator is seated
in the seat, the deck drive is disengaged, and the
speed control is placed in the neutral position with
the parking brake applied. The system also shuts
off the engine if the operator leaves the seat with
the mower running and the speed control is not in
the neutral postion with the parking brake applied.
It will also shut off the engine if the hopper is raised
with the cutter deck drive engaged. Never operate
equipment with the interlock system disconnected
or malfunctioning.
2.4 OPERATION CONSIDERATIONS
1. Know the function of all controls and how to stop
quickly.
2. Reduce speed and exercise extreme caution on slopes
and in sharp turns to prevent tipping or loss of control.
Be especially cautious when changing directions on
slopes.
WARNING:
DO NOT operate on steep slopes.To check a slope,
attempt to drive up it (with cutter deck down). If
machine can drive up the slope without the wheels
slipping, reduce speed and use extreme caution.
ALWAYS FOLLOW OSHA APPROVED OPERATION.
8. Be sure interlock switches are functioning correctly.
9. Fuel is flammable; handle with care. Fill fuel tank
outdoors. Never fill indoors. Use a funnel or spout to
inhibit spillage. Clean up any spillage before starting
the engine.
3. Do not stop or start suddenly. WHEN MOWING A
HILLSIDE, MOW UP AND DOWN THE FACE
OF SLOPES, NEVER ACROSS THE FACE.
10. DO NOT add fuel to a running or hot engine. An
explosion could occur. Allow engine to cool for several
minutes before adding fuel.
4. When using any attachment, never direct the discharge
of material toward bystanders or allow anyone near
the machine while in operation.
11. Keep flammable objects (cigarettes, matches, etc.),
open flames and sparks away from the fuel tank and
fuel container.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
5. Before attempting to start the engine, with the
operator in the seat, disengage power to the cutter
deck, place the hopper in the stowed position,
steering control levers in the neutral position and
engage the parking brake.
15. DO NOT touch the engine or the muffler while the
engine is running or immediately after stopping.
These areas may be hot enough to cause a burn.
16. DO NOT run engine inside a building or confined
area without proper ventilation. Exhaust fumes are
hazardous and could cause death.
6. If the mower discharge ever plugs, shut off the
engine, remove the ignition key, and wait for all
movement to stop before removing the obstruction.
Do not use your hand to dislodge the clogged
discharge chute. Use a stick or other device to
remove clogged material.
2.5 MAINTENANCE CONSIDERATIONS
1. Never make adjustments to the machine with the
engine running unless specifically instructed to do so.
If the engine is running, keep hands, feet, and
clothing away from moving parts.
7. Be alert for holes, rocks, and roots in the terrain and
other hidden hazards. Keep away from any dropoff.
Beware of overhead obstructions such as low limbs,
etc. and underground obstacles such as sprinklers,
pipes, tree roots, etc. Cautiously enter a new area.
Be alert for hidden hazards.
2. Remove the key from the ignition switch to prevent
accidental starting of the engine when servicing or
adjusting the machine.
3. Keep all nuts, bolts and screws tight to ensure the
machine is in safe working condition. Check blade
mounting bolts frequently to be sure they are tight.
8. Disengage power to cutter deck before backing up.
Do not mow in reverse unless absolutely necessary
and then only after observation of the entire area
behind the mower.
4. Do not change the engine governor settings or
overspeed the engine. See the engine operator's
manual for information on engine settings.
9. DO NOT turn sharply. Use care when backing up.
10. Disengage power to cutter deck before crossing
roads, walks or gravel drives. Watch for traffic when
crossing roads or operating near roadways.
5. To reduce fire hazard, keep the engine free of grass,
leaves, excessive grease and dirt.
6. Hydraulic fluid is under high pressure. Keep
body and hands away from pinholes or nozzles that
eject hydraulic fluid under high pressure. Use only
cardboard or paper to search for leaks. If you need
service on your hydraulic system, please see your
authorized Scag dealer.
11. Mow only in daylight or good artificial light.
12. Take all possible precautions when leaving the
machine unattended, such as disengaging the mower,
lowering the attachments, setting the parking brake,
stopping the engine, and removing the key.
7. Hydraulic fluid under high pressure may have
sufficient force to penetrate skin and cause serious
injury. If hydraulic fluid is injected into the skin, it
must be surgically removed within a few hours by a
doctor or gangrene may result.
13. Disengage power to the attachments when
transporting or when not in use.
14. The machine and attachments should be stopped and
inspected for damage after striking a foreign object,
and damage should be repaired before restarting and
operating the machine.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
2.6 SAFETY AND INSTRUCTIONAL DECALS
WARNING
INSTALL BELT COVER BEFORE
OPERATING MACHINE
READ OPERATOR'S MANUAL
481039
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
SPECIFICATIONS
3.1 ENGINE
General Type .............................................................................. Heavy Duty Industrial/Commercial Gasoline
Brands ........................................................................................ Kohler & Kawasaki
Model......................................................................................... 25HPKohler Command CH25S & 27HP Kawasaki FD750D
Horsepower................................................................................ 25HPat3600 RPM (SCR42-25CH, SCR48-25CH & SCR52-25CH)
................................................................................................... 27HP at 3600 RPM (SCR48-27KA & SCR52-27KA)
Type ........................................................................................... 4 Cycle Gasoline, Twin Cylinder, Horizontal Shaft
Displacement ............................................................................. Kohler - 725 cc. & Kawasaki - 745cc
Cylinders.................................................................................... 2 with Cast Iron Sleeves
Governor .................................................................................... Mechanical Type with Variable Speed Control Set At 3600 RPM
Idle Speed .................................................................................. 1400 RPM
Fuel Pump Group ...................................................................... Mechanical Fuel Pump with In-Line Fuel Filter, Fixed Jet
Carburetor with Smart-Choke™ and Fuel Shutdown Solenoid
Fuel ............................................................................................ Non-Leaded Gasoline with a Minimum Octane Rating of 87
Oil Pump Group: ....................................................................... Positive Displacement Gerotor™ Oil Pump with Remote Oil Filter
Starter ........................................................................................ Electric Starting with Cell Starter
Belts:
Engine Belt ............................................................................. Scag Part Number - 481976
Blower Drive Belt.................................................................... Scag Part Number - 481977
Pump Drive Belt ...................................................................... Scag Part Number - 481978
3.2 ELECTRICAL
Battery ....................................................................................... 12 Volt
Charging System........................................................................ Alternator
Charging Output ........................................................................ 12Volt, 15Amp
System Polarity.......................................................................... Negative Ground
Starter......................................................................................... 12 Volt Electric Solenoid Shift Type
Interlock Switches ...................................................................... Seat, Neutral Control, Mower Engagement (BBC), Hopper and
Parking Brake
Instrument Panel ........................................................................ Ammeter, Hourmeter, Key Switch, Throttle Lever, Manual Choke,
BBC Lever, Fuses, and Water Temp Gauge (KAOnly)
Fuses ......................................................................................... Two (2) 20Amp
3.3 TRACTOR
Drive System .............................................................................. Hydraulic Drive with Two Variable Displacement Pumps and Two
Cast-iron High Torque Motors
Hydrostatic Pumps .................................................................... Two Hydro-Gear BDP10LPumps with Dump Valves for
movement without running the engine
Drive Wheel Motors .................................................................. Two Ross Model MB 15cu. inch Cast-iron High Torque Motors
Steering/Travel Control.............................................................. Twin Lever Fingertip Steering Control with Individual Control to
Each Wheel
Parking Brake ............................................................................ Lever Actuated Linkage to Brakes on Both Drive Wheel Axles
Wheels:
(2) Front Caster ...................................................................... 11 x 4.0-5 Smooth Tires
(2) Drive ................................................................................. 23 x 9.5-12 Four-Ply Pneumatic Tubeless, Radius Edge
(1) Rear .................................................................................
Fuel Tank ................................................................................... Two, 3.75 gallon Polyethylene Tanks with Large Fuel Tank filler
neck and Fuel Gauge Fill Caps
Tire Pressure:
Front Caster .......................................................................... 25 PSI
Drive ..................................................................................... 12 PSI
Rear....................................................................................... 25 PSI
Seat ............................................................................................ Padded
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
-NOTE-
3.3 TRACTOR (CONT'D)
The machine will travel at 8.5 mph for
transport purposes. For best cutting
performance the forward travel speed
should be adjusted depending upon the
cutting conditions.
Travel Speed:
Forward ................................................................................. 0 - 8.5 MPH
Reverse .................................................................................. 0 -5.0 MPH
3.4 CUTTER DECK
No. of Blades ............................................................................. 3
Width of Cut .............................................................................. 42", 48" & 52"
Cutter Blades ............................................................................. Three (3) 16-1/2" (P/N 481997) Marbane Blades
Deck Drive ................................................................................. Belt Driven Manual Clutch Connected to a Drive Shaft to a
Gearbox on the Cutter Deck
Manual Clutch Type .................................................................. Manual blade engagement system with engagement lever and
double v-belt drive
Cutting Height Adjustment ........................................................ Four Corner PinAdjustment, 1.5" to 5" in 1/2" increments
Deck Tilt .................................................................................... Manually by Lifting Deck and Engaging Lock Pin
Drive Shaft ................................................................................. Shaft With Two High Speed U-Joints
3.5 GRASS CATCHING SYSTEM
Type ........................................................................................... Out-Front Rear Deck Discharge into Blower which discharges
the Grass Clippings into a Hopper
Hopper ....................................................................................... 90-Gallon Molded Plastic with Osillating Discharge Chute
Discharge Blower ...................................................................... 12" Diameter
Side Discharge ........................................................................... Extra Wide Discharge Opening on the Left Hand Side with Spring
Loaded Discharge Chute
3.6 HYDRAULIC SYSTEM
Hydraulic Oil Filter ................................................................... 10 Micron Spin-on Element Type
Hydraulic Reservoir ................................................................... Nylon; 6 Quart Capacity
3.7 WEIGHTS AND DIMENSIONS
SCR42-25CH SCR48-25CH SCR48-27KA
Length ........................................................................................ 95.0"
Overall Width ............................................................................. 42.0"
Overall Height ............................................................................ 44.0"
Operating Weight....................................................................... 1285 lbs.
95.0"
48.0"
44.0"
1260lbs.
95.0"
48.0"
44.0"
1300lbs.
SCR52-25CH SCR52-27KA
Length ........................................................................................ 95.0"
Overall Width ............................................................................. 52.0"
Overall Height ............................................................................ 44.0"
Operating Weight....................................................................... 1300lbs.
95.0"
52.0"
44.0."
1350lbs.
3.8 PRODUCTIVITY
The following chart will aid you in determining how many acres your Scag mower will cut per day.
The chart is an estimate based on 8 hours per day cutting time at 4 MPH with an allowance for overlap and turns.
Cutting Width:
Acres Per Day:
42" 48" 52"
20 21 23
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
OPERATING INSTRUCTIONS
2. Mower Deck Control (Figure 4-1). Used to engage
and disengage the mower drive system. Pushing the
lever forward will engage the deck drive. Pulling the
lever back will disengage the deck drive.
CAUTION:
Do not attempt to operate this mower unless you
have read this manual. Learn the location and
purpose of all controls and instruments before you
operate this mower.
3. Engine Choke Control (Figure 4-1). Used to
start a cold engine.
4. Engine Throttle Control (Figure 4-1). Used to
control the engine speed. Pushing the lever forward
increases engine speed. Pulling the lever back
decreases engine speed. Full back position is the
IDLE position. Full forward is the cutting position.
4.1 CONTROLS AND INSTRUMENT
IDENTIFICATION
Before operating the mower, familiarize yourself with all
mower and engine controls. Knowing the location,
function and operation of these controls is important for
safe and efficient operation of the mower.
5. Ammeter (Figure 4-1). Indicates the condition of
the charging system. When the engine is running the
needle should be at the positive end of the meter. If
the needle is on the negative end of the meter, this
indicates a discharge condition and the machine
should be taken in for service.
1. Ignition Switch (Figure 4-1). Used to start the
engine and has three positions; OFF, ON, and
START.
Left Steering
Control
Cutter Deck
Lift Lock
Right Steering
Control
Engine
Throttle Control
Park Brake
Control
Ammeter
Ignition Switch
Forward Speed
Control
Hour Meter
Engine
Choke Control
Mower Deck
Control
Fuses
Right Fuel
Gauge
Left Fuel
Gauge
SCR 2001 C&I
Figure 4-1 Controls and Instruments
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
6. Hour Meter (Figure 4-1). Indicates the number
of hours the engine has been operated. It operates
whenever the ignition switch key is in the ON
position. It can be used to keep track of
maintenance intervals and the amount of time
required to perform various tasks.
7. Fuse Holders (Figure 4-1). Two 20-amp fuses
protect the mower’s electrical system. To replace
fuses, pull fuse out of the socket and install a new
fuse.
Right
Dump
Valve
Left
Dump
Valve
8. Left Steering Control (Figure 4-1). Used to
control the mower's left wheel when traveling
forward or reverse.
SCR 2K DVL
Figure 4-2 Dump Valves Location
14. Blower Belt Release (Figure 4-3). This lever is
used to release the belt tension and allow the blower
belt to be removed when the cutter deck is setup as
either a mulching or a side discharge deck.
9. Right Steering Control (Figure 4-1). Used to
control the mower's right wheel when traveling
forward or reverse.
10. Parking Brake Control (Figure 4-1). Used to
engage and disengage the parking brakes and also
used to lock the cutter deck from tilting up too high
while traveling. Pull the lever back and lock in place
to engage the parking brakes. Push the lever
forward to disengage the parking brakes and engage
the deck tilt lock.
Blower Belt
11. Forward Speed Control (Figure 4-1). Used to
control the mower's forward speed. Push the lever
forward to increase the forward speed.
Blower Belt
Release Pedal
12. Fuel Tank Gauges (Figure 4-1). Indicates the
amount of fuel in the fuel tanks.
SCR 2K BBR
Figure 4-3 Blower Belt Release
13. Dump Valve Control Levers (Figure 4-2).
Located under the seat, on the hydraulic pumps, used
to “free-wheel” the mower. Rotating the levers
clockwise until they stop allows the unit to move
under hydraulic power. The levers must be in this
position during operation of the mower. Rotating the
levers counterclockwise, one turn, allows the mower
to be moved by hand (free-wheeling).
4.2 SAFETY INTERLOCK SYSTEM
The mower is equipped with a safety interlock system
that prevents the engine from starting unless the deck
drive is disengaged and the speed control is in neutral and
the parking brake is engaged. The interlock system shuts
off the engine if the operator leaves the seat with the
speed control in the neutral position and the parking
brake is not engaged and/or the cutter blades are
engaged. It will also shut the engine off if the cutter
deck drive is engaged and the hopper is raised.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
3. If the engine is cold, adjust the engine choke as
needed.
WARNING:
Never operate the mower with the interlock
system disconnected or malfunctioning. Do not
disengage or bypass any switch; injury to yourself
and others or property damage could result.
4. Adjust engine throttle control to about half engine
speed.
5. Turn the ignition key to the START position and
release the key as soon as the engine starts. Do not
hold the key in the START position for more than 15
seconds at a time. Allow at least 60 seconds
between each cranking attempt to prevent
overheating of the starter motor. Prolonged cranking
can damage the starter motor and shorten battery
life.
4.3 INITIAL RUN-IN PROCEDURES (First
Day of Use or Approximately 10 Hours)
1. Check all belts for proper alignment and wear after
the initial 2, 4, and 8 hours of operation. The belt
systems are self adjusting therefore tension
adjustment is not necessary.
6. Allow engine to warm before operating the mower.
2. Change the engine oil and oil filter after the first 5
hours of operation. (See Section 7.4.)
4.5 GROUND TRAVEL AND STEERING
-IMPORTANT-
3. Check hydraulic oil level in reservoir. (See Section
7.3.)
If you are not familiar with the operation of a
machine with lever steering and/or hydrostatic
transmissions, the steering and ground speed
operations should be learned and practiced in
an open area, away from buildings, fences, or
obstructions. Practice until you are comfortable
with the handling of the machine before
attempting to mow. Learn the operation on flat
ground before operating on slopes.
4. Check for loose hardware. Tighten as needed.
5. Check interlock system for proper operation. (See
Section 4.2.)
6. Check tire pressure. Inflate tires if necessary.
-IMPORTANT-
Start practice with a slow engine speed and slow
forward travel.
4.4 STARTING THE ENGINE
Do not push the steering control levers forward
when traveling forward. They are only used to
steer the mower and to travel in reverse by pulling
back on the levers.
CAUTION:
DO NOT USE STARTING FLUIDS. Use of starting
fluids in the air intake system may be potentially
explosive or cause a “runaway” engine condition
that could result in engine damage and/or personal
injury.
Learn to operate the mower with the left hand on
the steering levers and the right hand on speed
control as shown in Figure 4-4. Using both hands
on the steering levers often causes overcontrol.
1. Be sure the fuel shutoff valve, located on top of the
left fuel tank, is completely open. (See Section 7.4)
Learn to feather the steering controls to obtain a
smooth operating action. Jerky movements tend
to place extreme force on the drive pumps and
axles, as well as damage the lawns.
2. Sit in the operator’s seat and place the speed control
in the neutral position and engage the parking brake.
Practice operating the mower until you can make
it go exactly where you are aiming.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
In case of an emergency, such as loss of control,
stop the mower’s movement by quickly pulling the
forward speed control lever to the neutral position.
To steer the mower left while traveling forward, pull the
left steering lever back. The further the lever is pulled
back, the sharper the mower will turn left.
To steer the mower right while traveling forward, pull the
right steering control lever back. The further the lever is
pulled back, the sharper the mower will turn right.
Forward Travel
-NOTE-
Use one hand on both steering levers as shown in
Figure 4-4 to minimize overcontrol.
-NOTE-
Smooth operation of the steering levers will
produce a smooth mower operation. While
learning the operation of the steering controls,
keep the travel speed low.
To travel forward with the mower, move the speed control
lever forward. Do not push the steering control levers
forward as they are used only for steering the mower left
or right. When the speed control is moved forward, the
mower will travel forward at the speed the control lever is
set at. To increase the speed, push the control lever forward
and to decrease the speed, pull the control lever back. It is
not necessary to hold the speed control in position, since a
friction system holds the lever in position.
-IMPORTANT-
Do not travel forward over a curb. The mower
will hang up on the curb. Tilt the deck and
travel backwards over the curb at a 45 degree
angle. (See section 4.15 for cutter deck tilting
instructions)
To stop the forward travel, pull the speed control lever
back to the neutral position.
Reverse Travel
CAUTION:
Before backing up, observe the rear for persons
and obstructions. Clear the area before backing up.
Possible injury or property damage could occur.
CAUTION:
Disengage power to the mower before backing up.
Do not mow in reverse unless absolutely necessary
and then only after observation of the entire area
behind the mower.
To travel in reverse, pull both handles all the way back.
Keep the travel speed low while traveling in reverse.
-NOTE-
The mower will not travel straight in reverse.
Slight adjustments must be made using the
steering controls.
SCR 2K HOC
Figure 4-4 Hands On Controls
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
To steer left while traveling in reverse, allow the left
steering control lever to move forward. The further the
control is allowed to move forward, the sharper the
mower will turn left.
3. To disengage the deck drive, pull back the Cutter
Deck Control Lever to the disengage position.
4. Always operate the engine at full throttle to properly
maintain cutting performance. If the engine starts to
lug down, reduce the forward speed and allow the
engine to operate at maximum RPM.
To steer right while traveling in reverse, allow the right
steering control lever to move forward. The further the
control is allowed to move forward, the sharper the
mower will turn right.
4.7 HILLSIDE OPERATION
To stop the reverse travel, place the speed control lever
in the neutral position and allow the steering control
levers to return to the neutral position. If the mower is
to be parked, engage the parking brake and remove the
ignition key.
WARNING:
To minimize the possibility of overturning, the least
dangerous method of operating on hills and
terraces is to travel vertically up and down the slope,
not horizontally along the slope. Avoid any
unnecessary turns and travel at reduced speed.
4.6 ENGAGING THE DECK DRIVE (CUTTER
BLADES)
1. Set the throttle at about 3/4 speed. Do not attempt to
engage the deck drive at high speed — use only
moderate engine speed when engaging the deck
drive.
1. The mower has been designed for good traction and
stability under normal mowing conditions. However,
caution must be used when traveling on slopes,
especially when the grass is wet. Wet grass reduces
traction and steering control.
2. Engage the deck drive by pushing the Cutter Deck
Control Lever forward, (Figure 4-6) to the engage
position.
2. To inhibit tipping or loss of control, do not start or
stop suddenly, avoid unnecessary turns and travel at
reduced speed.
Cutter Deck
Control Lever
3. Keep tires properly inflated.
4. Always travel up or down the slope, whenever
possible; NEVER across the slope. (See Figures 4-6
and 4-7.)
SCR 2001MCD
Figure 4-5 Cutter Deck Control Lever
SCR 2K POS
Figure 4-6 Proper Operation on a Slope
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
4. Fill the fuel tank with fresh, clean fuel at the end of
every day of operation.
5. Check the tire pressure. Inflate tires if necessary.
4.10 HOPPER, MULCH or SIDE DISCHARGE
OPERATION
When mowing with the cutting deck setup for rear discharge
into the hopper (Figure 4-9), the blower belt must be installed.
A control lever located on the left side of the tractor (Figure
4-8) will release tension on the idler pulley to allow the belt
to be installed (grass catching operation) or removed
(mulching or side discharge operations). The cutter deck
must also be adapted to the type of cutting that the operator
is attempting to perform.
SCR 2K IOS
Figure 4-7 Improper Operation on a Slope
4.8 PARKING THE MOWER
1. Place the speed control in the neutral position.
2. Slow the engine to idle speed.
Blower Belt
3. Engage the parking brake.
4. Turn the ignition key to the OFF position and remove
the key.
Blower Belt
Release Pedal
4.9 AFTER OPERATION
SCR 2K BBR
Figure 4-8 Blower Belt Release
1. Wash the entire mower after each use. Do not use
high pressure spray or direct the spray onto electrical
components.
Rear Discharge
Baffle
-IMPORTANT-
Do not wash a hot or running engine. Cold
water will damage the engine. Use compressed
air to clean the engine if it is hot.
2. Keep the entire mower clean to inhibit serious heat
damage to the engine or hydraulic oil circuit.
SCR 2K RD
Side Discharge
Shutoff Baffle
3. Check the drive belts for proper alignment, correct if
necessary. Remove any debris build up.
Figure 4-9 Baffles for Rear Discharge
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Grass Catching Operation
Lock Pin and
Latch Plate
CAUTION:
Never leave grass clippings in the hopper after
mowing. Wet or damp clippings will generate heat
as they decompose which may cause spontaneous
combustion to occur.
1. With the hopper lowered, engage the deck drive. When
the deck drive is engaged, the grass delivery spout,
which is designed to distribute the grass clippings
through the inside of the hopper, will begin to oscillate.
-NOTE-
The mower has an interlock switch that will
prevent the mower from starting if the hopper is
in the raised position. This interlock switch will
also shut the engine off if the hopper is raised
while the engine is running and the deck drive is
engaged.
SCR 2K TGO
Figure 4-10 Tailgate Operation
B. Raise the tailgate until the lock pin on top of the
hopper engages with the latch on the tailgate
(Figure 4-10).
2. Proceed to mow the lawn until the hopper is full. If
your mower is not equipped with the optional
hopper fill alarm to tell you when the hopper is full,
check the hopper frequently when first using the
grass catcher. After operating with the grass catcher
for awhile, experience will tell you when the hopper
is full.
Grasp Here
Hopper Latch
4. When dumping the hopper into a disposal area:
A. Disengage the deck drive.
Hopper Prop Rod
SCR 2K RTH
Figure 4-11 Raising The Hopper
C. Stand off to side of the hopper. Unhook the
hopper latch and raise the hopper by placing a
hand in the hand hole at either bottom front side
of the hopper (Figure 4-11) and then carefully lift
the hopper until it is in its upright position. When
serivice is needed under the hopper, rotate the
hopper prop rod upward until it contacts the
hopper frame. This will prevent the hopper from
moving until the service is complete.
WARNING:
Never operate the grass catcher with the
hopper back door open. Objects can be
thrown out the spout of the hopper with a
force that can cause injury to bystanders or
property damage.
D. Carefully lower the hopper and hook the hopper
latch.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
E. Release the latch holding the tailgate and then
lower the tailgate.
Mulching Operation
Rear Discharge
Shutoff Baffle
Side Discharge Operation
CAUTION:
The side discharge deck can throw objects with great
force. Do not stand in front of discharge chute when
the cutter deck is engaged. Keep bystanders clear
from the area while mowing.
SCR 2K BMD
Side Discharge
Shutoff Baffle
When mowing, never discharge toward bystanders or
buildings. Do not allow anyone near the machine while
in operation.
Figure 4-13 Baffles for Mulching
1. Place the proper baffles in the cutter deck for
mulching operation (Figure 4-13).
Rear Dicharge
Shutoff Baffle
2. Release the tension from the blower belt and remove
the blower belt. (Figure 4-8, Page 15).
3. Engage the deck drive.
4. Proceed to mow the lawn.
4.11 REMOVING CLOGGED MATERIAL
SCR 2K BSD
Side Discharge
Chute
Figure 4-12 Baffles for Side Discharge
ROTATING BLOWER BLADES
NEVER PUTYOUR HANDS INTOTHE BLOWER DIS-
CHARGE CHUTE FOR ANY REASON! Shut off the
engine and remove the key and only then use a stick
or similar object to remove material if clogging has
occurred.
1. Place the proper baffles in the cutter deck and install
the side discharge chute (Figure 4-12).
1. If either blower discharge chute becomes clogged,
shut off the engine and remove the ignition key.
Using a stick or similar item, dislodge the clogged
material. Then resume normal mowing.
2. Release the tension from the blower belt and remove
the blower belt. (Figure 4-8, Page 15).
3. Engage the deck drive.
4. Proceed to mow the lawn.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
4.12 MOVING MOWERWITH ENGINE
STOPPED
4.14 ADJUSTING CUTTING HEIGHT
The mower deck can be adjusted from a height of 1 1/2-
inches to 5-inches at 1/2-inch intervals. To adjust the cutting
height:
To “free-wheel” or move the mower around without the
engine running, place the dump valve handle in the
FREE-WHEEL position (Figure 4-2, Page 11).
Disengage the parking brake and move the mower by
hand. The lever must be returned to the DRIVE position
to drive the mower.
WARNING:
Do not adjust the cutting height with the mower
blades rotating. Shut off the engine and remove
the ignition key. Bodily injury could occur from the
rotating blades.
4.13 RECOMMENDATIONS FOR MOWING
1. Do not mow with dull blades. A dull blade will tear
grass, resulting in poor lawn appearance and
requiring extra power.
1. Shut off the engine and remove the ignition key.
2. Direct the side discharge away from sidewalks or
streets to minimize cleanup of clippings. When
mowing close to obstacles, direct the discharge away
from the obstacles to reduce the chance of property
damage by thrown objects.
Remove
Hair Pins
3. Cut grass when it is dry and not too tall. Do not cut
grass too short (cut off 1/3 or less of existing grass
for best appearance). Mow frequently.
4. Keep mower and discharge system clean.
Deck Height
Adjustment Pin
5. When mowing wet or tall grass, mow the grass
twice. Raise the mower to the highest setting for the
first pass and then make a second pass to the desired
height.
SCR 2K DHA
Figure 4-14 Deck Height Adjustment
6. Use a slow travel speed for trimming purposes.
2. Remove the two hairpins from the adjusting pins on
one side of the cutter deck (Figure 4-14).
7. Operate the engine at or near full throttle for best
cutting. Mowing with a lower RPM causes the
mower to tear the grass. The engine is designed to
be operated at full speed.
3. Lift or lower the deck to the desired cutting height and
install the hairpins. A deck height decal is located on
the deck as an aid in adjusting the deck to the desired
height.
8. Use the alternate stripe pattern for best lawn
appearance. Vary the direction of the stripe each
time the grass is mowed to avoid wear patterns in
the grass.
4. Repeat the above process on the other side of the cutter
deck.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
4.15 TILTING THE CUTTER DECK
WARNING:
Do not tilt the mower deck with the mower blades
rotating. Shut off the engine and remove the ignition
key. Bodily injury could occur from the rotating
blades.
The mower deck can be tilted up for trailering, blade
replacement, etc. To tilt the deck up:
1. Shut off the engine, remove the ignition key and
engage the park brake.
Locking Pin
Hole
Deck Locking
Pin
SCR 2K DLP
Figure 4-15 Deck Locking Pin
2. Lift up on the caster wheel arm until the lock pin
engages into the lock pin hole (Figure 4-15).
3. To release the deck and lower it to its operating
position:
A. Lift up on the caster wheel arm while pulling up
on the lock pin.
B. Carefully lower the deck to the ground.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
TROUBLESHOOTING CUTTING CONDITIONS
CAUSE
CURE
CONDITION
Stringers - Occasional
Blades of Uncut
Grass
Low engine RPM
Run engine at full RPM
Ground speed too fast
Wet grass
Slow speed to adjust for conditions
Cut grass after it has dried out
Sharpen blades
Dull blades, incorrect sharpening
Deck plugged, grass accumulation
Belts slipping
Clean underside of deck
Adjust belt tension
Width of Deck
SGB020
Streaking - Strips of
Uncut Grass in Cutting
Path
Dull, worn blades
Incorrect blade sharpening
Low engine RPM
Belt slipping
Sharpen blades
Sharpen blades
Run engine at full RPM
Adjust belt tension
Deck plugged, grass accumulation
Ground speed too fast
Wet grass
Clean underside of deck
Slow speed to adjust for conditions
Cut grass after it has dried out
Replace blades
Width of Deck
Bent blades
SGB018
Streaking - Strips of
Uncut Grass Between
Cutting Paths
Not enough overlapping
between rows
Increase the overlap of each
pass
Width
of
Deck
Width
of
Deck
SGB019
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
TROUBLESHOOTING (CONT'D)
CAUSE
CURE
CONDITION
Uneven Cut on Flat
Ground - Wavy
High-Low
Lift worn from blade
Blade upside down
Replace blade
Mount with cutting edge toward
ground
Appearance,
Scalloped Cut, or
Rough Contour
Deck plugged, grass accumulation
Too much blade angle (deck pitch)
Deck mounted improperly
Bent spindle area
Clean underside of deck
Adjust pitch and level
See your authorized SCAG dealer
See your authorized SCAG dealer
Sharpen blade
Dull blade
Width of Deck
SGB020
Uneven Cut on
Uneven Ground -
Wavy Appearance,
Uneven ground
May need to reduce ground speed,
raise cutting height, and/or change
direction of cut
High-Low Scalloped
Cut, or Rough Contour
Width of Deck
SGB021
Sloping Ridge Across
Width of Cutting Path
Tire pressures not equal
Wheels uneven
Check and adjust tire pressure
Check and adjust tire pressure
See your authorized SCAG dealer
Check for level and correct
Deck mounted incorrectly
Deck not level side-to side
Width of Deck
SGB023
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
TROUBLESHOOTING (CONT'D)
CAUSE
CURE
CONDITION
Scalping - Blades
Hitting Dirt or
Cutting Very Close to
the Ground
Low tire pressures
Ground speed too fast
Cutting too low
Check and adjust pressures
Slow speed to adjust for conditions
May need to reduce ground speed,
raise cutting height, change direction
of cut, and/or change pitch and level
Rough terrain
May need to reduce ground speed,
raise cutting height, and/or change
direction of cut
Ground speed too fast
Wet grass
Slow speed to adjust for conditions
Cut grass after it has dried out
Width of Deck
SGB022
Step Cut - Ridge
in Center of
Cutting path
Blades not mounted evenly
Bent blade
Adjust pitch and level
Replace blade
Internal spindle failure
See your authorized SCAG dealer
See your authorized SCAG dealer
Mounting of spindle incorrect
Width of Deck
SGB024
Slope Cut - Sloping
Ridges Across Width
of Cutting Path
Bent spindle mounting area
Internal spindle failure
Bent deck housing
See your authorized SCAG dealer
See your authorized SCAG dealer
See your authorized SCAG dealer
Width of Deck
SGB025
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
R
ADJUSTMENTS
6.1 PARKING BRAKE ADJUSTMENT
Park Brake Control
WARNING:
Do not operate the mower if the parking brake is
not operable. Possible severe injury could
result.
The parking brake linkage should be adjusted whenever
the parking brake lever is placed in the “ENGAGE”
position and the parking brake will not prevent the mower
from moving. If the following procedures do not allow
you to engage the parking brake properly, contact your
Scag dealer for further brake adjustments.
Park Brake Control Rod
1. Position a floor jack under the left side of the
machine behind the drive wheel. Raise the machine
and support it to prevent it from falling. Block the
caster wheels to prevent the machine from moving.
Remove the right drive wheel and reinstall (2) lug
nuts to hold the hub on.
SCR 2K BLA
2
Figure 6-2 Brake Switch Adjustment
3. With the brake in the engaged position, check the
distance between the lower nut on the brake actuator
rod and the spring housing. The distance should be
approximately 1/16". (See Figure 6-3).
2. With the brake lever in the engaged position, check
to see if the lever plunges the brake switch within
1/8" of bottoming out. (See Figure 6-1). To increase
the distance, loosen the jam nuts on the parking
brake control rod and turn the rod clockwise. To
decrease the distance, turn the rod counterclockwise.
(See Figure 6-2).
4. Turn the nut at the top of the brake connector link
until the 1/16" measurement is achieved and tighten
the jam nut at the connector link on the brake
actuator rod. (See Figure 6-3).
5. Repeat steps 3 and 4 on other side. Replace the
drive wheels and test the brake.
-NOTE-
If this procedure does not achieve proper brake
adjustment, please contact your authorized Scag
dealer for diagnosis and repair.
Brake
Switch
1/8"
SCR 2K BSA
Figure 6-1 Brake Switch
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
R
CAUTION:
Stop the engine and remove the key from the
ignition before making any adjustments. Wait for
all moving parts to come to a complete stop
before beginning work.
CAUTION:
The engine and drive unit can get hot during
operation causing burn injuries. Allow engine
and drive components to cool before making any
adjustments.
1/16"
Neutral Adjustment
-IMPORTANT-
Before proceeding with this adjustment, be sure that
the tire pressure is correct, that the caster wheels
turn freely, and that the transmission drive belt
tension spring is not broken.
SCR 2K BAR
1. Jack up the machine enough to lift the drive wheels
and block securely.
Spring Housing
Figure 6-3 Brake Actuator Rod Assembly
2. Pull the speed control lever into the neutral position.
3. Pull the park brake lever into the fully engaged position.
6.2 TRAVEL ADJUSTMENTS
Neutral or tracking adjustments will need to be made if:
4. Adjust the speed control lever turnbuckle until the speed
control lever contacts the park brake lever and tighten
the jam nuts. (See Figure 6-4).
A. The speed control lever is in neutral and the
machine creeps forward or backward. (Neutral
Adjustment)
Speed Control
Linkage
B. The mower pulls to one side or the other when
traveling in a forward direction. (Tracking
Adjustment).
Speed Control
Lever
No Gap
No Gap
If the mower creeps forward or backward as indicated in
"A" above, the neutral linkages must be adjusted. Start
with adjusting the speed control lever and proceed as
directed. To correct the tracking of the mower (mower
pulls to one side when traveling in a forward direction),
adjust the tracking of the mower as described on page 23.
Brake Lever
SCR 2K CDA
Figure 6-4 Speed Control Lever
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
R
SCR 2K TAD
Figure 6-5 Drive linkage
9. When the speed control lever is actuated, the mower
should travel in a straight line. If it does not travel
straight, perform the TrackingAdjustment
procedures.
5. Start the engine and disengage the parking brake.
6. Loosen jam nuts C and D (See Figure 6-5) on the
right side. Slowly rotate the control rod until the right
drive wheel starts to creep forward. When the wheel
starts to creep forward, stop the movement and turn
the control rod back until the wheel starts to creep in
reverse. When the wheel starts to creep in reverse,
stop the movement and turn the control rod to the
center point between forward and reverse motion
(Figure 6-4) and tighten the jam nuts.
Tracking Adjustment
-IMPORTANT-
Before proceeding with this adjustment, be sure that
the tire pressure is correct, that the caster wheels
turn freely, and that the transmission drive belt
tension spring is not broken.
7. Loosen jam nuts A and B (See Figure 6-5) on the left
side. Slowly rotate the control rod until the left drive
wheel starts to creep forward. When the wheel
starts to creep forward, stop the movement and turn
the control rod back until the wheel starts to creep in
reverse. When the wheel starts to creep in reverse,
stop the movement and turn the control rod to the
center point between forward and reverse motion
(Figure 6-5) and tighten the jam nuts.
The mower tracking should be adjusted if the machine does
not travel in a straight line during forward travel.
Preform the neutral adjustment before proceeding with the
tracking adjustment.
1. If the machine pulls to the right, loosen the jam nuts
on the right control rod and turn the rod slightly
clockwise, tighten the jam nuts and retest.
8. Remove the blocking and lower the drive wheels to
the ground.
2. If the machine pulls to the left, loosen the jam nuts on
the left control rod and turn the rod slightly clockwise,
tighten the jam nuts and retest.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
R
Cutter Deck Engagement Belt Adjustment
Gap
Keep Handles
Aligned
This adjustment should be made after the initial break
in (first 8 Hours of operation) and checked every 40
hours thereafter.
Adjustment Bolt
1. Check the tension on the belt. (See Figure 6-6).
There should be 1/2" deflection with 10lbs. of force
at the longest span between pulleys.
2. To increase or decrease the belt tension, loosen the
jam nuts on the control rod and turn until the proper
belt tension is achieved. (See Figure 6-6)
SCR 2K SHA
Figure 6-7 Steering HandleAdjustment
4. Maintain gap between steering handles. If gap does
not exist, contact your authorized Scag service center.
Control Rod
Belt Tension
6.3 THROTTLE CONTROL AND CHOKE
ADJUSTMENT
These adjustments must be peformed by your Scag
dealer to ensure proper and effecient running of the
engine. Should either need adjustment, contact your
authorized Scag service center.
SCR 2001 CDBA
WARNING:
Before removing any guards, shut the
engine off and remove the ignition key.
Figure 6-6 Engagement Belt Adjustment
Steering HandleAdjustment
The steering handles should be positioned in line with each
other for easy one-handed control. (See Figure 6-7). The
handles can then be adjusted forward or backwards to
accommodate the operator.
6.4 BELT ADJUSTMENT
All drive belts and cutter deck belts are spring loaded and
self-tensioning. The belts should be checked periodically
for proper alignment and wear.
1. Shut off the mower’s engine and engage the parking
brake.
6.5 BELT ALIGNMENT
2. Loosen the two bolts for each steering handle and pivot
the handles forward or back as desired.
Belt alignment is important for proper performance of
your Scag mower. If you experience frequent belt wear
or breakage, see your authorized Scag service center for
belt adjustment.
3. Keep the handles aligned and tighten the bolts.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
R
5. Cutter deck pitch is adjusted by loosening the locknut
on each of the front cutter deck height adjuster pins
and turning the pins until 1/4" pitch (front edge of cutter
deck is 1/4" lower than the rear edge of the cutter deck)
is achieved. Tighten the locknuts securely once the
proper adjustment has been set.
6.6 CUTTER DECK ADJUSTMENTS
The mower deck can be adjusted from a height of 1-1/2-
inches to 5-inches at 1/2-inch intervals. To adjust the
cutting height:
WARNING:
Do not adjust the cutting height with the cutter
blades rotating. Shut the engine off and remove
the key from the ignition. Bodily injury could
occur from the rotating blades.
1. Shut off the engine and remove the key from the ignition.
2. Remove the hairpins from the adjusting pins on one side
of the cutter deck. (See Figure 6-8).
3. Lift or lower the deck to the desired cutting height by
using the handles supplied on the cutter deck. (See
Figure 6-8). Reinstall the hairpins at the desired cutting
height. A deck height decal is located on the deck
mounting frame as an aid in adjusting the deck to the
desired height.
4. Repeat the above process for the other side of the cutter
deck.
Remove Pins
Rear Adjuster Pin
Handle
SCR 2K CDA
Figure 6-8 Cutter Deck Adjustment
WARNING:
NEVER engage the cutter deck without the belt
cover in place.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
MAINTENANCE
7.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS
HOURS
Break-In
(First 10)
8
40 100 200 500
Procedure
Comments
X
X
X
Check all hardware for tightness
Check hydraulic oil level
See paragraph 7.3
See paragraph 7.8
See paragraph 7.4
Check all belts for tightness
Change engine oil and filter
X
(First 5)
X
Fill fuel tank before starting
Use unleaded gasoline
with a minimum
octane rating of 87
X
X
X
X
X
X
X
Check engine oil level
*Clean mower
See paragraph 7.4
See paragraph 7.14
See paragraph 7.9
See paragraph 7.2
See paragraph 7.11
See paragraph 7.6
See paragraph 7.10
See paragraph 7.7
Check condition of blades
Apply grease to fittings
Clean screen in hopper
*Check/clean air intake
Check tire pressure
X
Check battery electrolyte level,
clean battery posts and cables
X
X
X
X
Check belt
See paragraph 7.8
See paragraph 7.2
See paragraph 7.4
See paragraph 7.6
Apply grease to fittings
Change engine oil
*Clean air cleaner element
X
X
Check engine belts for wear
Check lubricant in gearboxes
See paragraph 7.8
See paragraph 7.13
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS (CONT'D)
HOURS
Break-In
(First 10)
8
40 100 200 500
Procedure
Comments
X
X
X
X
X
X
Apply grease to fittings
Check hardware for tightness
Change engine oil filter
Check hydraulic oil level
Replace engine fuel filter
See paragraph 7.2
See paragraph 7.4
See paragraph 7.3
See paragraph 7.5
Drain hydraulic system and
replace hydraulic oil
See paragraph 7.3
Use SAE 20W50
Motor Oil
X
X
Replace hydraulic oil filter
See paragraph 7.3
See paragraph 7.13
Replace power unit gearbox
lubricant
X
Replace lubricant in cutter deck
gear boxes
See paragraph 7.12
* Perform these maintenance procedures more frequently under heavy load, extreme dusty or dirty
conditions.
7.2 LUBRICATION
GREASE FITTING LUBRICATION CHART
(SEE FIGURE 7-1)
LUBRICATION
NO. OF
LOCATION
INTERVAL
LUBRICANT
PLACES
1
2
3
4
5
6
7
8
9
Brake Linkage
100 Hours/Bi-Weekly
100 Hours/Bi-Weekly
100 Hours/Bi-Weekly
100 Hours/Bi-Weekly
100 Hours/Bi-Weekly
100 Hours/Bi-Weekly
50 Hours/Bi-Weekly
100 Hours/Bi-Weekly
40 Hours/Weekly
8 Hours/Daily
Chassis Grease
2
Caster Wheel Pivot
Caster Wheel Bearings
Cutter Deck Pivots
Brake Lever
Chassis Grease
2
2
2
1
1
3
4
3
1
1
1
Chassis Grease
Chassis Grease
Chassis Grease
Rear Wheel Bearings
Cutter Deck Drive Shaft
Steering Control Levers and Linkage
Cutter Deck Spindles
Chassis Grease
Chassis Grease
Chassis Grease
+Lithium MP White Grease 2125
+Lithium MP White Grease 2125
Chassis Grease
10 Blower Bearing
11 Cutter Deck Engagement Lever
12 Elbow Pivot (Inside Hopper)
40 Hours/Weekly
40 Hours/Weekly
Chassis Grease
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
+
Compatible Greases: Mobilix #2 found at Mobil Service Stations
Ronex MP found at Exxon Service Stations
Super Lube MEP #2 & Super Stay-M #2 found at Conoco Stations
ShellAlvania #2 found at Shell Service Stations
Lidok EP #2 found at industrial shops
RIGHT SIDE
11
2
6
7
4
7
9
3
8
5
8
12
UNDER SEAT
2
6
3
10
4
9
1
SCR 2001 LFP
LEFT SIDE
Figure 7.1 Lubrication Fitting Points
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
A black color and/or a rancid odor usually indicates
possible overheating of the oil, and a milky color usually
indicates water in the hydraulic oil.
7.3 HYDRAULIC SYSTEM
A. Checking Hydraulic Oil Level
-Note-
The hydraulic oil level should be checked after the first
10 hours of operation. Thereafter, check the oil after
every 200 hours of machine operation or monthly,
whichever occurs first.
The hydraulic oil should be changed if you
notice the presence of water or a rancid odor
to the hydraulic oil.
1. Park the mower on a level surface and stop the
engine.
-IMPORTANT-
If the oil level is consistently low or leaks are
noticed, check for leaks and correct immedi-
ately.
2. Place a suitable container under the hydraulic oil
filter. Remove the cap from the tee installed in the
hydraulic oil filter head. (Figure 7-2). Allow the fluid
to drain into the container and properly discard it.
1. Wipe dirt and contaminants from around the
reservoir cap. Remove the cap from the hydraulic
oil reservoir.
3. Remove the oil filter element (Figure 7-2) and
properly discard it. Fill the new filter with clean oil
and install the filter. Hand tighten only.
2. Visually check the level of hydraulic oil. Hydraulic
oil must be at least 2-1/4" inches from top of the filler
neck. If the level cannot be determined visually, use
a clean tape measure to check the level. If the fluid
is low, add 20W50 motor oil. DO NOT overfill;
(overfilling the oil reservoir may cause oil seepage).
4. Install the cap onto the tee and be sure it is tight.
5. Remove the fill cap from the reservoir and fill the
reservoir to 2-1/4" inches from the top of the filler
neck with 20W50 motor oil.
3. Clean the fill cap and install it onto the reservoir.
6. Replace the reservoir fill cap.
Hydraulic
Reservoir
Hydraulic
Drain Port
7. Start the engine and drive forward and backward for
two minutes. Check the oil level in the reservoir. If
necessary, add oil to the reservoir.
7.4 ENGINE OIL
A. Checking Engine Crankcase Oil Level
Hydraulic
Oil Filter
The engine oil level should be checked after every 8
hours of operation or daily as instructed in the Engine
Operator’s Manual furnished with this mower.
SCR 2K HOR
Figure 7-2 Hydraulic Oil Reservoir
B. Changing Hydraulic Oil
The hydraulic oil should be changed after every 500
hours or annually, whichever occurs first. The oil should
also be changed if the color of the fluid has become
black or milky.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
Engine Oil
Filler Cap
7.5 ENGINE FUEL SYSTEM
To avoid injury from burns, allow the mower
to cool before removing the fuel tank cap and
refueling.
Engine Oil
Dip Stick
Engine Oil
Filter
SCR 2K FCDS
Figure 7-3 Engine Fill Cap and Dip Stick
B. Changing Engine Crankcase Oil
After the first 5 hours of operation, change the engine
crankcase oil and replace the oil filter. Thereafter,
change the engine crankcase oil after every 100 hours of
operation or bi-weekly, whichever occurs first. Refer to
the Engine Operator’s Manual furnished with this mower
for specific instructions.
SCR 2001 EOF
Figure 7-5 Engine Oil Filter
A. Filling the FuelTank
Fill the fuel tank at the end of each operating day to
within 1 inch below the filler neck. Do not overfill. Use
clean, fresh unleaded gasoline with a minimum octane
rating of 87.
Engine Oil
Drain Plug
B. Replacing In-Line Fuel Filter Element
SCR 2K EODP
The in-line fuel filter (Figure 7-6) should be replaced
after every 500 hours of operation or annually, whichever
occurs first.
Figure 7-4 Engine Oil Drain Plug
C. Changing Engine Oil Filter
1. Close the shutoff valve. Remove the two clamps
securing the fuel filter to the fuel hose. Remove the
fuel filter.
After the first 5 hours of operation, replace the engine oil
filter. Thereafter, replace the oil filter after every 200
hours of operation or every month, whichever occurs
first. Refer to Engine Operator’s Manual for specific
instructions.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
4. Replace the air cleaner after six cleanings or after every
500 hours of operation or annually, whichever occurs
first.
Fuel Shutoff
Valve
7.7 BATTERY
A. Checking Electrolyte Level and Cleaning
Battery
After every 40 hours of operation or weekly, whichever
occurs first, check the electrolyte level in the battery and
clean the battery and connections. Dirt and fluid on the
top of the battery can cause the battery to discharge.
Corrosion of the battery terminals or loose connections
will cause poor battery performance.
Fuel Filter
SCR 2K FSFF
Figure 7-6 Fuel Shutoff and Fuel Filter
2. Install a new fuel filter. Be sure it is installed in the
proper direction. Secure to the fuel hose using the
two clamps. Wipe up any spilled gasoline and
dispose of rags in an approved container.
WARNING:
Lead-acid batteries produce flammable and
explosive gases.To avoid personal injury when
checking, testing or charging batteries, DO
NOT use smoking materials near batteries.
Keep arcs, sparks and flames away from
batteries. Provide proper ventilation and wear
safety glasses.
7.6 ENGINE AIR CLEANER
A. Cleaning and/or Replacing Air Cleaner
Element
For any air cleaner, the operating environment dictates
the air cleaner service periods. Inspect and clean the air
cleaner element after every 100 hours of operation or bi-
weekly, whichever occurs first and replace the element if
required.
WARNING:
Electric storage battery fluid contains sulfuric
acid which is POISON and can cause SEVERE
CHEMICAL BURNS. Avoid contact of fluid
with eyes, skin, or clothing. Use proper
protective gear when handling batteries. DO
NOT tip any battery beyond 45° angle in any
direction. If fluid contact does occur, follow
first aid suggestions below.
-NOTE-
In extremely dusty conditions it may be neces-
sary to check the element once or twice daily to
prevent engine damage.
1. Remove the wing nut securing the air cleaner cover
to the engine. Remove the air cleaner cover and set
aside.
2. Remove the nut securing the clamping plate and the
air cleaner to the engine. Remove the clamping plate
and set aside. Remove the air cleaner and inspect.
3. Clean or replace the air cleaner and foam pre-
cleaner as neccessary.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
B. Charging the Battery
WARNING:
Refer to the battery charger’s manual for specific
instructions.
BATTERY ELECTROLYTE FIRST AID
EXTERNAL CONTACT — Flush with water.
Under normal conditions the engine’s alternator will have
no problem keeping a charge on the battery. If the
battery has been completely discharged for a long period
of time, the alternator may not be able to recharge the
battery, and a battery charger will be required.
EYES — Flush with water for at least 15
minutes and get medical attention
immediately.
DO NOT charge a frozen battery. It may explode and
cause injury. Let the battery warm before attaching a
charger.
INTERNAL — Drink large quantities of water.
Follow with Milk Of Magnesia, beaten egg,
or vegetable oil. Get medical attention
immediately. In case of internal contact, DO
NOT give fluids that would induce vomiting.
Whenever possible, remove the battery from the mower
before charging and make sure the electrolyte covers the
plates in all cells.
1. Tilt the seat forward to access the battery.
WARNING:
2. Remove the battery cell caps. Visually inspect
electrolyte level in the cells. If electrolyte is
BATTERIES PRODUCE EXPLOSIVE
GASES. Charge the battery in a well
ventilated space so gases produced
while charging can dissipate.
below the bottom of vent well, fill with clean distilled
water to the bottom of vent wells (1/4 to 1/2 inch
above the plates). Install the battery cell caps.
-IMPORTANT-
Do not overfill the battery. Electrolyte will
overflow through the vent tube onto parts of
the machine, resulting in severe corrosion.
Charging rates between 3 and 50 amperes are
satisfactory if excessive gassing or spewing of
electrolyte does not occur or the battery does not feel
excessively hot (over 125°F). If spewing or gassing
occurs or the temperature exceeds 125°F, the charging
rate must be reduced or temporarily stopped to permit
cooling.
3. Clean the cable ends and battery posts with steel
wool or a wire brush. Use a solution of baking soda
and water to clean the battery. Do not allow the
solution to enter the battery cells.
C. Jump Starting
4. Tighten the cable connections securely and apply a
light coat of silicone dielectric grease to the terminal
connections to prevent corrosion.
1. The booster battery must be a 12 volt type. If a
vehicle is used for jump starting, it must have a
negative ground system.
2. When connecting the jumper cables, connect the
positive cable to the positive battery post, then
connect the negative cable to the negative battery
post.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
7.8 DRIVE BELTS
B. Blade Sharpening
After the first 2, 4, 8 and 10 hours of operation, check for
proper tension on all drive belts and check for any damage.
Thereafter, check the belt tension after every 100 hours of
operation or bi-weekly, whichever occurs first.
-NOTE-
DO NOT sharpen the blades beyond 1/3 of the
width of the blade.
1. Sharpen the cutting edge at the same bevel as the
original. See Figure 7-8. Sharpen only the top of the
cutting edge to maintain sharpness.
1. Check the belts for cracks, tears, and excessive wear.
Replace any damaged belts.
7.9 CUTTER BLADES
Angle Blade Back
Do Not Cut In
A. Blade Inspection
1. Remove the ignition key before servicing the blades.
2. Tilt the mower deck and secure in place.
X
X Must NOT Exceed
1/3 Blade Width
30
2002SGB033
WARNING:
Figure 7-8 Blade Sharpening
Never operate the cutter blades with the deck
in the raised position because it is hazardous
and damage to mower will result.
2. Check the balance of the blade. If the blades are out
of balance, vibration and premature wear can occur.
See your authorized Scag dealer for blade balancing
or special tools, if you choose to balance your own
blades.
3. Check the blades for straightness. If the cutter
blades appear bent, they will need to be replaced.
C. Blade Replacement
WARNING:
1. Remove the ignition key and engage parking brake
before replacing the blades.
Do not attempt to straighten a bent blade, and
never weld a broken or cracked blade. Always
replace it with a new blade to assure safety.
2. Tilt the mower deck and secure in place with lock
pin.
4. If a blade cutting edge is dull or nicked, it should be
sharpened. Remove the blades for sharpening. See
"Blade Replacement."
-IMPORTANT-
Spindle blade bolts are left handed thread.
-NOTE-
3. Secure the cutter blades to prevent them from
rotating, (use the optional Blade Buddy tool, P/N
9212, to assist in securing the cutter blades), remove
the nut from the blade attaching bolt. Remove the
cutter blade, bolt and spacer from the spindle shaft.
Keep the blades sharp. Cutting with dull blades
not only yields a poor mowing job, but slows the
cutting speed of the mower and causes extra wear
on the engine and the blade drive.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
4. To install the new blade, put the flat washer onto the
blade bolt and slide the bolt into the hole in the cutter
blade.
CAUTION:
Cutter deck gearbox can reach high operating
temperatures. Allow cutter deck gearbox to
cool before servicing.
5. Install the spacer onto the blade bolt and insert the
belt into the cutter spindle shaft.
6. Install the hex nut to the blade bolt at the top of the
cutter spindle. Secure the blades from rotating using
a Blade Buddy and torque to 75 ft-lbs.
The fluid level in the cutter deck gearbox should be
checked after every 100 hours of operation or
bi-weekly, whichever occurs first.
7.10 TIRES
1. Remove the ignition key and engage the parking
brake.
Check the tire pressures after every 8 hours of operation
or daily.
2. Lift the foot plate up to gain access to the gearbox.
Caster Wheels ........................................ 25 PSI
Rear Wheel............................................. 25 PSI
Drive Wheels ......................................... 12 PSI
3. Clean and remove the check plug from the side of
the gearbox. See Figure 7-9. Visually check the fluid
level in the plug port. The fluid level must be up to
the bottom of the plug port. If the fluid level is low,
fill gearbox through the check plug port with EP 80-
90 gear oil. Install the check plug and tighten
securely.
7.11 HOPPER
The hopper screen should be cleaned after every 8 hours
of operation or daily, whichever occurs first. It may be
necessary to clean the screen more frequently when
cutting wet and/or dirty grass.
GEARBOX FLUID
CHECK PLUG
1. Remove the hopper screen from the hopper.
2. Wash the screen using a water hose until all the screen
holes are clean.
3. Install the cleaned screen in the hopper.
-IMPORTANT-
Do not use the hopper with the screen removed.
Grass clippings will discharge from the hopper
with the screen removed.
SCR 2002 GFC
Figure 7-9 Gearbox Check Plug
7.12 CUTTER DECK GEARBOX
B. Changing Lubricant
A. Checking Lubricant Level
The lubricant in the cutter deck gearbox should be
changed after every 500 hours of operation or yearly,
whichever occurs first.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
1. Remove the hair pins and raise the cutter deck to the
highest cut position (5").
8. Using the caster wheel arm, lift the cutter deck
frame assembly off the cutter deck and secure in
place with the lock pin.
2. Using the caster wheel arm, lift up the cutter deck and
secure in place with the lock pin.
9. Clean and remove the check plug from the side of
the gearbox and fill the gearbox with SAE 80W90
lubricant until fluid is level with the bottom of the plug
port. Install check plug.
3. Beneath the cutter deck is an access hole to gearbox
drain plug. See Figure 7-10. Clean the area thoroughly
and then place a suitable container under the drain plug.
10. Lower the cutter deck frame assembly onto the
cutter deck and install the washers and hair pins onto
the height adjust pins.
GEARBOX DRAIN
PLUG
7.13 POWER UNIT GEARBOX
A. Checking Lubricant Level
1. Remove the ignition key and engage the parking
brake.
SCR 2K GBF
2. Lift the seat to gain access to the gearbox dipstick.
See Figure 7-12.
Figure 7-10 Gearbox Drain Plug
4. Remove the drain plug and lower the cutter deck over
the container to drain the lubricant.
5. Using the caster wheel arm, lift up the cutter deck and
secure in place with the lock pin. Properly discard the
drained fluid.
6. Install drain plug and lower the cutter deck.
7. Remove the (4) four hair pins and washers from the
deck height adjust pins.
Gearbox
Dipstick
Remove
Hair Pins
SCR 2K GDS
Figure 7-12 Gearbox Dipstick
3. Remove and clean the dipstick. Visually check the
fluid level on the dipstick. The fluid level must be
between the (2) two marks on the dipstick. See
Figure 7-13. If the fluid level is low, fill the gearbox
through the dipstick tube with EP 80-90 gear oil.
Install the dipstick after proper fluid level has been
achieved.
Deck Height
Adjustment Pin
SCR 2K DHA
Figure 7-11 Deck Height Pins
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
FLUID LEVEL
SCR 2K DS
Figure 7-13 Fluid Level
B. Changing Lubricant
The lubricant in the power unit gearbox should be
changed after every 500 hours of operation or yearly,
whichever occurs first.
1. Beneath the power unit is an access hole to the
gearbox drain plug. Clean the area thoroughly and
place a suitable container under the drain plug.
2. Remove the drain plug and drain the lubricant into
the container and properly discard.
3. Reinstall the drain plug and add EP-80/90 lubricant
through the dipstick tube. Approximately 6 ounces of
fluid will be needed to fill the gearbox. Follow the
procedure in section 7.13 A. Checking Lubricant
Level, to fill the gearbox to the proper level.
7.14 BODY, DECK, HOPPER AND
UPHOLSTERY
CAUTION:
Do not wash any portion of the equipment
while it is hot. Do not wash the engine; use
compressed air.
1. After each use, wash the mower, deck and hopper.
Use cold water and automotive cleaners. Do not use
pressure cleaners.
2. Do not spray electrical components.
3. Use a mild soap solution or a vinyl/rubber cleaner to
clean the seat.
4. Repair damaged metal surfaces and use Scag touch-
up paint available from your authorized Scag dealer.
Wax or polish the mower for maximum paint
protection.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER DECKS
To Gearbox
25
24
65
69
14
61
69
73
13
12
16
74
76
26
69
75
61
12
69
61
50
11
25
A
49
24
78
50
12
14
80
15
14
5
28
B
59
31
81
25
24
3
A
51
29
22
6
9
79
23
68
29
24
29
23
63
59
48
53
21
27
54
25
52
20
8
68
27
70
30
27
59
53
36
B
63
71
29
35
34
59
37
72
38
33
1
77
7
40
39
41
58
64
18
32
62
4
32
42
57
59
10
60
55
59
43
45
17
38
52
2
56
19
67
47
44
46
66
SCR 2K CD
40
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER DECKS
Ref. Part.
Ref. Part.
No. Number
Description
42 48 52
No. Number
Description
42 48 52
42
43
44
45
46
47
48
49
50
51
52
53
54
55
55
56
43312
43296
481025
43297
481035
04040-10
482077
482076
482134
Spacer, Outside
Spacer, Inside
Seal, Bottom
Bushing, Spindle Bottom
Nut, Special 1 - 1/16-18
Flat Washer 5/8"
Hinge, Rear Chute
Tube, Discharge 8" ID
Clamp, Duct 8"
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
461365
461330
461371
46631
482486
481632
43515
482075
422478
481625-01
423366
422807
423367
422808
43590
482336
481979
482338
48926
48141
482148
48924
481522
481435
48753
482449
482450
482451
451398
451126
451393
451397
451091
43512
Cutter Deck with Decals
Cutter Deck with Decals
Cutter Deck with Decals
Spindle Assembly
Gearbox, Cutter Deck
Wheel, Anti-Scalp
Pin, Front Deck Height Adjust.
Pin, Rear Deck Height Adjust.
Bracket, Anti-Scalp Wheel
Knob w/Stud
x
x
x
x
2
3
4
5
6
7
8
9
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
451117
Chute, Rear Discharge
Bolt, HH 5/16-18 x 1.0"
Lockwasher, 5/16"
04001-09
04030-03
04040-15
461419
461329
461415
461328
461411
482245
04001-108
04021-10
04001-158
04020-29
04001-10
04110-03
04063-08
04063-01
04001-19
04030-04
04003-12
04001-01
04003-04
04019-03
04001-77
482426
LH Belt Cover
LH Belt Cover
RH Belt Cover
RH Belt Cover
x
x
Washer, Flat 5/16"
x
Chute, Side Discharge
Chute, Side Discharge
Bracket, Side Discharge Chute
Bracket, Side Discharge Chute
Bracket, Side Discharge Chute
Spring, Discharge Chute
Bolt, HH 5/16-18 x 4.5"
Nut, Elastic Stop 5/16-18
Bolt, 5/8-11 x 9.5" LH Thread
Nut, 5/8-11 LH Thread
Bolt, HH 5/16-18 x 1.25"
U-Nut, 3/8-16
Key, 1/4 x 1/4 x 2.0"
Key, 1/4 x 1/4 x 1.25"
Bolt, 3/8-16 x 1.0"
Lock Washer 3/8" Spring
Bolt, Carriage 5/16-18 x .75"
Bolt, HH 1/4-20 x .75"
Bolt, Carriage 5/16-18 x 1.0"
Nut, Serr. Flng. 5/16-18
Bolt, HH 3/8-16 x 3.5"
Driveshaft
Nut, Elastic Stop 3/8-16
Bolt, Hex Head 3/8-16 x 1-3/4"
Key, 1/4 x 1/4 x 1-1/4"
Baffle, Rear
Baffle, Rear
Baffle, Rear
Bolt, Hex Head 3/8-16 x 1-3/4"Gr.8 x
Roll Pin
Hair Pin Cotter
Flatwasher, 5/8-.688 x 1.750 x .134 x
x
x
x
x
x
x
x
10
11
Spacer, Spindle Bottom
Belt, Cutter Deck Drive
Belt, Cutter Deck Drive
Belt, Cutter Deck Drive
Hub, Tapered 1.125" bore
Hub, Tapered 1.00" bore
Pulley, 4.75" OD Tapered Bore
Pulley, 5.75" OD Tapered Bore
Spring, Belt Tension
Pulley, 5.35" OD Tapered Bore
Pulley, 6.35" OD Tapered Bore
Blade, Cutter 14.5" LH
Blade, Cutter 16.5" LH
Blade, Cutter 18.0" LH
Skirt, Weldment Bolt On
Skirt, Weldment Bolt On
Skirt, Weldment Bolt On
Baffle, Bolt On
Baffle, Bolt On
Spacer
Plate, Gearbox Mounting
Idler Arm
Bearing, Ball
Flat Washer 3/8"
Nut, Elastic Stop 3/8-16
Pulley, Idler
Bolt, Hex Head 3/8-16 x 3"
Bolt, Hex Head 3/8-16 x 1.5 GR8
Nut, Serr. Flng. 3/8-16
Pivot, Idler Arm
x
x
x
x
x
x
x
x
x
x
x
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
12
13
14
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
15
16
x
x
x
x
x
x
x
17
18
19
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
422426
451096
48224
04021-09
04001-21
04063-01
423336
451092
451394
04001-135
04060-08
04062-04
04040-10
04043-04
04021-09
482416
04001-54
04001-136
04019-04
422713
48269
48100-15
04021-05
04003-26
04017-27
43298
x
x
x
x
x
x
78
79
80
81
x
x
x
x
x
x
Pulley, Idler 5.0"
Bushing .376 ID Oilite
Lock Nut, 3/8-16 Center Lock
Bolt, Carriage 3/8-16 x 4.0"
Bolt, Hex Serr. Flng. 3/8-16 x 1.0"
Shaft, Spindle
Seal, Top
Bearing Assenbly
Grease Fitting
Relief Fitting, Grease
Housing, Spindle
481024
481022
48114-04
48677
43294
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER DECK SUPPORT COMPONENTS
2
33
3
6
1
7
4
2
5
3
33
3
34
31
32
35
8
9
10
30
29
28
11
27
12
26
13
25
12
15
20
21
24
18
14
17
19
22
23
20
16
SCR 2001 CDSC
42
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER DECK SUPPORT COMPONENTS
Ref.
No.
Part.
Number
Description
42
48
52
1
2
3
4
5
6
7
482078
Cover, Spring
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
04001-52
04019-06
481993
04021-09
04001-19
423234
Bolt, Hex Head 1/2-13 x 2.5"
Nut, 1/2-13 Serrated Flange
Spring, Cutter Deck LIft
Nut, 3/8-16 Elastic Stop
Bolt, Hex Head 3/8-16 x 1"
Footplate
422775
481284
48114-04
451386
451196
Footplate
Bumper, Rubber
Fitting, Grease
x
x
x
x
x
x
8
9
10
x
x
x
Frame, Cutter Deck Mounting
Frame, Cutter Deck Mounting
Frame, Cutter Deck Mounting
Pin, Quick
Bushing, 1" ID Oilite
Plug, 1/4-28
Yoke, Caster
Nut, 1/2-13 Elastic Stop
Spacer
Bolt, Hex Head 1/2-13 x 6.5"
Wheel, Caster 11 x 4.0-5 (Incl. items #19 through #24)
Tire, 11 x 4.0-5
Retainer
Roller Bearing .625 x 3.25"
Rim, 5.0 x 3.25"
x
451381
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
04066-01
48100-17
482028-01
45325
04021-07
43511
04001-80
481843
482192
481770
481769
481844
481846
48114-05
481245
43543
481992
04060-08
451199
04003-04
04021-10
04019-03
04040-10
43530
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Roller Bearing .625 x 1.0"
Fitting, Grease
Knob, Cutter Deck Release
Rod, Threaded
Spring
Pin, Roll 3/16 x 1.5"
Pin, Deck Frame Pivot
Bolt, Carriage 5/16-18 x 1"
Nut, 5/16-18 Elastic Stop
Nut, 5/16-18 Serrated Flange
Flatwasher, 5/8-.688 x 1.750 x .134
Bushing
04050-16
Snap-Ring
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SHEET METAL
54
1
2
56
17
51
3
3
53
55
57
54
37
4
5
6
52
7
51
53
57
55
8
37
71
70
10
11
18
9
A
43
52
12
13
73
34
16
14
19
15
50
72
52
47
45
36
B
31
65
13
14
12
74
49
44
33
A
24
42
48
30
46
47
66
35
58
25
51
21
C
67
63
68
18
62
C
27
23
B
48
58
26
52
38
29
64
68
52
40
47
47
59
32
58
69
69
39
53
53
61
48
60
58
28
19
22
48
53
58
20
58
41
SCR 2K SMC
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SHEET METAL
Ref. Part.
Ref. Part.
No. Number
Description
No. Number
Description
1
2
3
4
5
6
7
8
481559
04021-20
481657
481025
04021-13
482028-01
451187
04001-41
43021
482043
482192
481897
481896
481897
481894
48114-06
451186
461319
451171
451173
451174
451177
451178
482220
451179
48015
461473
422855
451415
422976
423311
422936
423031
423233
482204
04029-03
482074
48657
422935
423252
422934
451288
451256
423005
422988
04001-19
04030-04
04019-04
04003-33
04019-05
04001-20
04021-09
04041-07
04001-07
04021-07
04040-07
04030-06
Cap, Grease
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
04001-32
04001-63
04021-10
04017-16
43512
04003-01
04029-01
04021-09
43462
04060-01
04003-12
04019-03
04021-10
04032-01
04001-09
481625-01
04110-03
Bolt, Hex Head 3/8-16 x 1.25"
Bolt, Hex Head 5/16-18 x 3.5"
Nut, Elastic Stop 5/16"
Bolt, Capscrew 5/16-18 x .75"
Spacer
Bolt, Carriage 1/4-20 x 6"
Wing Nut, 1/4-20 x .75"
Nut, Elastic Stop 3/8-16
Pin
Roll Pin, Spring 5/32 x .75"
Bolt, Carriage 5/16-18 x .75"
Nut, Serrated Flange 5/16-18
Nut, Elastic Stop 5/16-18
Washer
Bolt, Hex Head 5/16-18 x 1"
Knob, w/stud 3/8-16 x 1-1/4"
U-Nut, 3/8-16
Nut, Elastic Jam 1.0-14
Bearing, 1.0 Diameter
Seal, 2.00 OD x 1.625 ID
Nut, Elastic Stop 5/8-11
Plug, 1/4-28
Yoke, Wheel
Bolt, Hex Head 5/8-11 x 9.5"
Spacer
Wheel Assy, 16 x 6.5-8 (Inc. # 11 thru # 16)
Tire, 16 x 6.5-8
Seal, Wheel Bearing
Cone, Bearing
Cup, Bearing
Rim Assy, (Includes Item # 12, 13, 14, & 16)
Fitting, Grease
Weldment, Rear Caster Support
Weldment, Main Frame RH
Weldment, Main Frame LH
Weldment, Axle Support
Weldment, Seat Support
Plate, Front Crossmember
Weldment, Seat Plate
Seat Assy.
Weldment, Deck Stop
Battery, purchase locally
Cover, Instrument Panel
Rear, Instrument Panel
Weldment, Gearbox Support
Plate, Gearbox Upper
Mount, Fuel Tank Rear
Box, Battery
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
Heatshield
Cover, PTO Clutch
Spring, Seat
Knob
Pad, Rubber Hopper Rest
Pad, Rubber
Bracket, Hydraulic Filter Mounting
Bracket, Fuel Tank Front
Catch, Cutter Deck
Weldment, Engine Deck
Weldment, Muffler Guard
Bracket, Oil Cooler
Rod, Hopper Prop
Bolt, Hex Head 3/8-16 x 1"
Lockwasher 3/8"
Nut, Serrated Flange 3/8-16
Bolt, Carriage 7/16-14 x 1"
Nut, Serrated Flange 7/16-14
Bolt, Hex Head 3/8-16 x 1.5"
Nut, Elastic Stop 3/8-16
Flatwasher, 3/8"
Bolt, Hex Head 1/2-13 x 1.5"
Nut, Elastic Stop 1/2-13
Flatwasher 1/2"
Lockwasher 1/2"
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOWER ASSEMBLY
4
40
39
36
37
20
19
35
17
15
25
14
38
13
41
2
18
33
32
32
16
12
29
12
31
3
30
28
11
27
22
7
A
10
29
1
23
21
26
25
24
23
9
8
A
6
7
26
34
5
SCR 2K BLOWER
46
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOWER ASSEMBLY
Ref. Part.
Ref. Part.
No. Number Description
No. Number Description
1
451202
422812
451116
461321
451201
461326
481995
Blower Housing, Rear
36
37
38
39
40
41
04003-23 Bolt, Carriage 3/8-16 x 1.0
04021-10 Nut, Elastic Stop 5/16-18
04003-06 Bolt, Carriage 1/4-20 x 1.0
04021-08 Nut, Elastic Stop 1/4-20
2
Blower Housing, Front
3
Inlet
4
Outlet
5
Fan
48677
Relief Fitting
6
Idler Arm, Weldment (includes #22)
Spring
04024-02 Push Nut, 3/8 Thread
7
8
04050-15 Ring, Retaining 2.5 ext.
421665 Washer, Retainer
48100-12 Bushing, Oilite 2.505 ID
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
481024
481022
43296
43312
481025
43297
Seal, 2.00 OD x 1.50 Bore
Bearing Assembly
Spacer, Inside
Spacer, Outside
Seal, 2.00 OD x 1.625 Bore
Bushing
04063-21 Key, 1/4 x .874 Woodruff
481468
481106
Pulley, 5.25 OD
Nut, 1-1/16 - 18 LH Thread
48114-09 Grease Fitting, 65 degree angle
04003-21 Bolt, Carriage 3/8-16 x 2.5"
461326
48224
Idler Arm w/pivot
Bearing
04043-04 Flatwasher 3/8"
04021-09 Nut, Elastic Stop 3/8-16
04019-04 Nut, Serr. Flng. 3/8-16
04001-46 Bolt, HH 3/8-16 x 2.25"
43282
04043-04 Flat Washer 3/8"
482079 Pulley, 3.0" diameter
Spacer
04021-09 Nut, Elastic Stop 3/8-16
04019-04 Nut, Serr. Flng. 3/8-16
43212
Spacer
04001-136 Bolt, HH 3/8-16 x 1.5"
04001-11 Bolt, HH 5/16-18 x 1.5"
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE AND ATTACHING PARTS
59
56
53
59
56
2
55
48
50
51
56
52
54
60
56
60
49
57
43
47
3
A
48
56
PART OF
ENGINE
47
5
PART OF
ENGINE
60
60
1
PART OF
ENGINE
4
6
46
14
44
45
A
62
43
42
58
41
39
38
14
To Engine
40
36
7
8
6
32 34
63
35
33
37
61
PART OF
ENGINE
8
10
11
9
32
15
31
30
29 16
28
27
26
14
16
20
22
24
26
25
6
23
12
18
13
15
20
20
21
17
To Blower
To Deck
Drive Shaft
19
SCR 2001 EAP
48
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE AND ATTACHING PARTS
Ref. Part.
No. Number Description
Ref. Part.
No. Number Description
32
33
34
35
36
04030-04 Lock Washer, 3/8"
1
481967
482271
481946
482081
481947
481944
482329
Engine, 25 HP Kohler (Spec.PS-68650)
Engine, 27 HP Kaw.(Spec. FD750D-AS04)
Muffler
43503
48224
481788
Pivot, Idler
Bearing, Idler Arm
Pulley, 5.45" OD - 1.125 Bore
2
3
4
Pipe, Exhaust
04063-20 Key, 1/4 x1/4 x 1"
Manifold, Exhaust, Kohler
Manifold, Exhaust, Kawasaki
Spring, Exhaust
04063-23 Key, 1/4 x 1/4 x 3-1/4"
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
423014
Mounting Bracket, Idler
5
04021-09 Nut, Elastic Stop 3/8"
04001-30 Bolt, Hex Head 3/8-16 x 4"
04030-04 Lock Washer, 3/8"
6
04001-01 Bolt, Hex Head 1/4-20 x .75"
423006 Guard, Oil Cooler, Kohler Only
7
8
04019-02 Nut, Serrated Flange 1/4-20
04021-09 Nut, Elastic Stop 3/8-16
482331
482263
482231
451293
Rod End, 3/8-24 LH Female
9
Belt
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
48058
Hose, Fuel 1/4" ID (order by the inch)
Link, PTO
423005
451401
Bracket, Oil Cooler, Kohler Only
Weldment, Engine Deck
Bracket, PTO
Nut,
04001-20 Bolt, Hex Head 3/8-16 x 1.5"
48926
Hub, Tapered 1.125" Bore
04001-14 Capscrew, Hex Head 1/4-20 x 1"
04050-02 External E-Ring
Flatwaser,
48141
Hub, Tapered 1" Bore
04063-01 Key, 1/4 x 1/4 x 1.25"
451296
482250
461334
482233
482232
482330
451297
Bellcrank Weldment, Front
481977
481435
482500
482223
423236
Belt, Blower
Grip, PTO Lever
Pulley, 5.35" OD
Gearbox, T-Drive
Dipstick Assembly
Bracket, Dipstick Tube
Lever Weldment, PTO Engagement
Linkage Assembly, PTO Upper
Linkage Assembly, PTO Center
Rod End, 3/8-24 RH Female
Bellcrank Weldment, Rear
Nut, Center Lock
04030-03 Lock Washer, 5/16"
04001-08 Bolt, Hex Head 5/16-18 x 3/4"
04040-14 Flatwasher, 1/4-.312 x .750 x .065
04021-08 Nut, Elastic Stop 1/4-20
04020-14 Nut, 3/8-24 LH Thread
04020-17 Nut, 3/8-24 RH Thread
Bolt, Carraige
423115
482133
423078
482067
Spacer, Fan
Fan, Cooling
Bolt, Carraige
Disk, Fan Support
Pulley, 4.95" OD Tapered Bore
461015
482067
482249
Idler Arm
Pulley, 4.95" OD Tapered Bore
Pulley, Idler 4" Dia.
04001-31 Bolt, Hex Head 3/8-16 x 2.5"
04021-09 Nut, Elastic Stop 3/8-16
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTION DRIVE COMPONENTS
30
33
33
27
27
32
29
To Back of
Engine Block
11
25
12
15
14
23
9
28
24
26
31
20
16
8
7
4
6
22
3
9
34
13
12
9
10
5
9
5
17
19
21
8
6
7
2
17
27
17
1
18
SCR 2001 TD
9
17
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTION DRIVE COMPONENTS
Ref. Part
No. No.
Description
1
48551
Pump, Hydraulic
2
3
461015
481994
Idler, Arm
Spring, Idler
4
5
6
7
482135
48224
04021-05
43212
Pulley,Idler
Bearing, Idler Arm
Nut, 3/8-16 Center Lock
Spacer
8
9
04019-04
04043-04
43077
Nut, 3/8-16 Serrated Flange
Washer, Flat 3/8”
Spacer
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
04001-160
48586
482062
48413
04001-31
481978
04021-09
422927
04003-05
04003-12
04063-14
422928
Bolt, 3/8-16 x 3.0”
Pulley, 5.45” OD
Pulley, 4” OD
Pulley, 4” OD
Bolt, Hex Head 3/8-16 x 2.5”
Belt, Pump Drive
Nut, Elastic Stop 3/8-16
Plate,PumpMounting
Bolt, Carriage 3/8-16 x 1.5”
Bolt, Carriage 5/16-18 x .75”
Key, 5mm x 5mm x 25mm
Plate, Keeper
43542
481788
Spacer
Pulley, 5.45” OD
Bolt, 3/8-16 x 6”
04001-100
04001-31
04030-04
04012-04
461317
461318
43277
451205
04001-19
04019-03
Bolt, Hex Head 3/8-16 x 2.5”
Washer, Lock 3/8”
Setscrew, .312-18 Thread
Cover, Belt Front
Cover, Belt Rear
Spacer
Heatshield
Bolt, Carriage 3/8-16 x 1"
Nut, Serr. Flange 5/16-18
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC PUMP
26
30
25
24
Overhaul Seal Kit
23
27
28
22
1
29
19
20
21
17
16
3
15
18
11
2
14
13
12
10
5
6
8
7
11
9
4
390S0167
52
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC PUMP
Ref. Part
No. No.
Description
1
2
3
4
HG 2513017
HG 2513016
HG 9004800-2506
HG 9007314-0810
Housing Kit (Includes Housing, Journal Bearing)
EndCap
Straight Headless Pin
Socket Head Screw 5/16-18x1.0
5
6
7
HG 2003067
HG 2513027
HG 50273
End Cap Gasket
Charge Pump Kit (Includes Charge Cover, Gerotor Assy., O-Ring)
Gerotor Assembly
8
9
HG 9004101-1340
HG 2510064
HG 50095
O-Ring
Charge Relief Valve Kit
Socket Head Screw
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
HG 2510027
HG 2513030
HG 9006110-0120
HG 70079
Check Valve Kit (Includes Check Plug, Spring, O-Ring, Orifice Check Valve)
Bypass Valve Kit (Includes Bypass Valve, O-Ring, Back-up Ring)
Backup Ring
Cylinder Block Kit
Block Spring
Block Thrust Washer
Roller Thrust Bearing
Swash Plate
Trunnion Arm
Guide Slot
Cradle Bearing
Lip Seal
Pump Shaft
Ball Bearing
RetainingRing
Lip Seal
HG 2003014
HG 2003017
HG 2003044
HG 2003087
HG 2003005
HG 2000015
HG 2003023
HG 9008000-0126
HG 2003020
HG 2003043
HG 2003016
HG 9008000-0128
HG 2003052
HG 2003018
HG 2513038
HG 2513018
RetainingRing
Spacer
Shaft Kit (Includes Pump Shaft, Ball Bearing, Retaining Ring)
Overhaul Seal Kit (Includes Gasket, Trunnion Seal, Input Shaft Seal, Charge Pump O-Ring)
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER DECK DRIVE GEARBOX
7
7
2
1
6
4
1
5
2
2002 SCR CDDG
3
54
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER DECK DRIVE GEARBOX
Ref. Part
No. No.
Description
1
2
3
4
5
6
7
482122
482123
481651
Shaft Assembly
Shaft Assembly
Seal, 1.00” x 1.50” x 3/16”
481652-01 Plug, 1/8” NPT Socket Head
481652-02 Plug, 1/4” NPT Socket Head
04015-16 Bolt, 5/16-18 x 1.25”
482225
End Cap
55
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED AND STEERING CONTROLS
24
38
37
25
42
20
34
28
39
41
2
35
33
36
44
3
42
4
40
28
6
2
1
34
20
44
3
28
9
8
4
32
26
19
28
32
27
29
1
7
6
6
9
9
30
17
21
16
16
5
10
27
8
28
30
30
26
8
22
7
31
28
11
17
7
31
28
16
13
12
43
16
17
14
15
13
16
23
18
SCR 2K SSC
45
56
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED AND STEERING CONTROLS
Ref. Part
No. No.
Description
1
48551
Pump, Hydraulic
2
3
4
422969
421203
48829
Lever, Pump
Clamp,PumpControl
Block, Pump Control
5
6
7
8
482177
48464
48544
Rod, Threaded 3/8-24 x 14.675”
Rod End, 3/8-24 RH Thread Female
Rod End, 3/8-24 LH Thread Female
Nut, Jam 3/8-24 LH Thread
Nut, Jam 3/8-24 RH Thread
Rod, Threaded 3/8-24 x 2.925”
Spring, Torsion RH
Spring, Torsion LH
Weldment, Steering Control
Spacer, Lever Stop
Weldment, Speed Control LH
Buching, .753 ID Sint.
Fitting, Grease 1/4-28
Shaft, Steering Lever
Rod, Threaded 3/8-24 x 3.75”
Disc, Friction
04020-26
04020-25
482178
482060
482059
451183
43541
451181
48100-06
48114-04
43544
482176
481243
451182
04001-100
04021-09
481245
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Weldment, Speed Control RH
Bolt, Hex Head 3/8-16 x 6”
Locknut, 3/8-16 Elastic
Knob, Speed Control Lever
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
451298
422438
481477
04021-09
04001-20
04001-21
43512
43212
04032-04
422198
04021-13
04017-18
04001-46
04020-12
04019-03
43277
04001-122
04001-08
04001-32
04001-59
48796
Lever, Speed Control
Lever, Steering
Grip, Steering Lever
Nut, Elastic Stop 3/8-16
Bolt, Hex Head 3/8-16 x 1.5”
Bolt, Hex Head 3/8-16 x 1.75”
Spacer
Spacer
Washer, Belleville 5/8”
Plate, Speed Selector
Nut, Elastic Stop 5/8-11
Bolt, 5/16-18 x 1.25” Capscrew
Bolt, Hex Head 3/8-16 x 2.25”
Nut, 3/8-16 Jam
Nut, 5/16-18 Serrated Flange
Spacer
Bolt, Hex Head 5/16-18 x 2.25”
Bolt, Hex Head 5/16-18 x .75”
Bolt, Hex Head 3/8-16 x 1.25”
Bolt, Hex Head 1/4-20 x 1.25”
Bushing, Self-Aligning
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5 unless otherwise noted.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
PARKING BRAKE MECHANISM
44
38
45
5
4
34
3
13
2
35
13
33
1
39
41
42
37
7
14
42
36
40
8
29
37
6
37
42
7
29
7
10
32
10
10
9
9
41
11
42
12
13
10
7
10
9
11
12
13
37
40
18
10
7
15
31
29
9
26
37
41
30
40
46
47
16
17
17
28
19
20
23
31
21
27
22
25
24
SCR 2002 PBL
58
Download from Www.Somanuals.com. All Manuals Search And Download.
PARKING BRAKE MECHANISM
Ref. Part
No. No.
Description
1
2
3
4
5
6
7
8
461320
482058
48544
04020-17
04004-39
04020-14
48343-04
481990
Lever, Parking Brake
Grip, Parking Brake Lever
Rod End, 3/8-24 LH
Nut, 3/8-24 LH Thread
Rod, 3/8-24 x 9.5"
Nut, 3/8-24 RH Thread
Clevis, 3/8-24
Spring
9
04001-162
04020-14
451260
48807
04041-07
451224
Bolt, Hex Head 3/8-24 x 8.25"
Nut, 3/8-24
Weldment, Brake Rod
Spring
Flatwasher, 3/8"
Weldment, Brake
10
11
12
13
14
15
16
17
18
19
20
461469
461470
481601
48114-05
48589
Weldment, Brake Linkage
Weldment, Brake Linkage
Band, Brake
Fitting, Grease
Drum, Brake
481529
Motor, Hydraulic Wheel
21
22
23
24
25
461438
04008-01
48680
04061-06
04028-01
Hub, Wheel
Stud, Wheel Mounting 1/2-20
Nut, Castle 1.0-20 UNF
Pin, Cotter 9/16" x 1.5"
Nut, Lug 1/2-20
26
27
04021-10
482185
481833
482186
482044
Nut, Elastic Stop 5/16-18
Wheel Assy 23 x 8.50-12 (42" Only)
Tire, 23 x 8.50-12 (42" Only)
Rim W/Valve Stem (42" Only)
Wheel Assy 23 x 9.50-12 (48" & 52")
Rim W/Valve Stem (48" & 52")
Tire, 23 x 9.50-12 (48" & 52")
Key, Woodruff 5/16 x 1"
Pin, Rue Cotter 3/8" Diameter
Pin, Clevis 3/8" Diameter x 2"
Locknut, Hex 1/2-13 Center Lock
Weldment, Deck Stop
481659
482194
28
29
30
31
32
04063-25
04069-01
04064-03
04021-19
451179
33
34
35
36
37
38
39
40
41
42
43
44
45
46
451295
Weldment, Brake Shaft
Bolt, Hex Head 5/16-18 x .75"
Nut, Elastic Stop 5/16-18
Bushing, Self-Aligning
Pin, Clevis 3/8 x 1.06"
Nut, Elastic Stop 3/8-16
Bolt, Hex Head 3/8-16 x 1.5"
Pin, Cotter 3/32 x .75"
Bolt, Hex Head 5/16-18 x 1"
Nut, Serrated Flange 5/16-18
Nut, Elastic Stop 5/16-18
E-Clip,.875"
04001-08
04021-10
482061
04064-02
04021-09
04001-20
04061-02
04001-09
04019-03
04021-04
04050-12
04063-20
451073
Key, 1/4 x 1/4 x 1"
Brake Linkage Weldment, LH
47
451074
Brake Linkage Weldment, RH
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5 unless otherwise noted.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL AND HYDRAULIC COMPONENTS
5
6
15
38
3
15
38
15
1
14
4
37
20
1
7
15
15
35
7
37
4
37
To Right Side
Fuel Tank
27
36
9
8
9
15
10
20
10
To Engine
33
34
35
12
15
37
27
16
17
36
30
34
33
11
11A
18
32
28
29
28
31
19
16
13
22
29
30
15
2
4
27
21
27
4
30
29
25
28
26
23
24
23
24
SCR 2002 FHC
60
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL AND HYDRAULIC COMPONENTS
Ref. Part.
No. Number Description
1
48811
Hose, 3/8 Pushlock 20" Long (order by the inch)
Hose, 3/8 Pushlock 30" Long (order by the inch)
Tee, Swivel 9/16-18 JIC
2
48811
3
482277
481960
481164
481507
4
Hose Assembly, LH
5
Cap, Hydraulic Tank
6
Insert, Filler Neck
7
482266-01 Elbow, 9/16 O-Ring x 3/8 Hose
481467-03 Connector, O-Ring to Hose Barb
8
9
48058
Fuel Hose 1/4" ID
10
11
11A
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
48059-01
481989
482055
481958
48309
Clamp, Fuel Hose 1/4" Hose ID
Valve, Fuel Shutoff (LH Tank)
Tube, Fuel Standoff (RH Tank)
Cap, Fuel Tank w/gauge
Bushing, Tank
461437
48136-07
Hydraulic Tank
Clamp
482266-01 Elbow, 9/16 O-Ring x 3/8 Hose
482417
Filter Head
04001-09
04021-10
Bolt, Hex Head 5/16-18 x 1"
Nut, Elastic Stop 5/16-18
481467-01 Connector, 7/16 O-Ring x Hose Barb
48758
Filter, Hydraulic
422939
04010-10
04110-01
481957
422940
481961
48350-02
48603-02
48938-02
48571-02
482481
48136-05
482499
48811
Strap, Fuel Tank Rear
Screw, 1/4-20 x 2"
U-Nut, 1/4-20
Fuel Tank
Strap, Fuel Tank Front
Hose Assembly, RH
Elbow, 90 Degree 1/2 x 1/2
O-Ring
O-Ring Bushing, 5/8 Tube
Cap, 3/4-16 JIC
Fitting, Tee Special
Clamp
Hose, Return Line
Hose, 3/8 Pushlock 36" Long (order by the inch)
Pump, BDP 10L
48551
48572-04
48811
Tube, Union 1/2 x 1/2
Hose, 3/8 Pushlock 5" Long (order by the inch)
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
KOHLER ELECTRICAL SYSTEM
TO HOPPER
HARNESS
19
31
30
C
2
3
C
B
29
4
5
6
28
7
33
B
C
2
35
27
26
25
34
3
15
8
9
1
10
16
13
A
14
18
9
9
11
22
12
10
24
23
17
A
19
20
32
21
SCR 2001 EKH
62
Download from Www.Somanuals.com. All Manuals Search And Download.
KOHLER ELECTRICAL SYSTEM
Ref. Part.
No. Number Description
Ref. Part.
No. Number Description
1
04040-15 Flatwasher, 5/16-.375 x .875 x .083
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
04020-02 Nut, 1/4-20
2
482318
482319
Wire Harness, SCR
48029-19 Battery Cable, Black
48029-20 Battery Cable, Red
04001-44 Bolt, Hex Head 1/4-20 x 1/2"
48030-18 Cable Clamp, Double
04021-01 Nut, Elastic Stop #10
3
Wire Harness, Hopper
4
48017-03 Lockwasher, Internal 5/8"
48017-04 Nut, 5/8-32 Special
5
6
48017-02 Key & Ring (includes 2 keys)
7
48798
48788
Keyswitch w/hardware
Relay
42413
48298
481755
Bracket, Fuse Holder
Fuse, 20 Amp
Ammeter
8
9
04031-01 Lockwasher, #10 external tooth
04020-01 Nut, #10-32 UNF
10
11
12
13
14
15
16
17
18
19
20
04030-04 Lockwasher, 3/8"
04001-18 Bolt, Hex Head
48023
Hour Meter
451185
Instrument Panel, Lower
04110-02 U-Nut, 5/16-18
04010-11 Screw, #10-32 x 1-1/2"
04030-03 Lockwasher, 5/16
04001-09 Bolt, Hex Head 5/16-18 x 1"
04010-01 Screw, #10-32 x 1/2"
482157
48430
Fuse, 15 Amp
Fuse Holder W/Fuse & Connector
482032
481545
481638
481637
482313
Control Cable
Switch, PTO
Switch, Seat
Switch, Brake & Hopper
Interlock Module
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
KAWASAKI ELECTRICAL SYSTEM
TO HOPPER
HARNESS
19
31
30
C
2
37
3
11
C
B
29
4
5
6
28
34
7
B
C
2
35
27
26
25
36
18
33
3
15
8
9
1
10
16
13
A
14
9
9
22
12
10
24
23
17
A
19
20
32
21
SCR 2001 EKA
64
Download from Www.Somanuals.com. All Manuals Search And Download.
KAWASAKI ELECTRICAL SYSTEM
Ref. Part.
No. Number Description
Ref. Part.
No. Number Description
1
04040-15 Flatwasher, 5/16-.375 x .875 x .083
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
04020-02 Nut, 1/4-20
2
482317
482319
Wire Harness, SCR
48029-23 Battery Cable, Black
48029-22 Battery Cable, Red
04001-44 Bolt, Hex Head 1/4-20 x 1/2"
48030-18 Cable Clamp, Double
04021-01 Nut, Elastic Stop #10
3
Wire Harness, Hopper
4
48017-03 Lockwasher, Internal 5/8"
48017-04 Nut, 5/8-32 Special
5
6
48017-02 Key & Ring (includes 2 keys)
7
48798
48788
Keyswitch w/hardware
Relay
42413
48298
481755
Bracket, Fuse Holder
Fuse, 20 Amp
Ammeter
8
9
04031-01 Lockwasher, #10 external tooth
04020-01 Nut, #10-32 UNF
10
11
12
13
14
15
16
17
18
19
20
04030-04 Lockwasher, 3/8"
04001-18 Bolt, Hex Head
04110-02 U-Nut, 5/16-18
48023
Hour Meter
451185
Instrument Panel, Lower
04030-03 Lockwasher, 5/16
481183
Water Temp Gauge
04001-09 Bolt, Hex Head 5/16-18 x 1"
04010-01 Screw, #10-32 x 1/2"
04010-11 Screw, #10-32 x 1-1/2"
48430
Fuse Holder W/Fuse & Connector
482032
481545
481638
481637
482313
Control Cable
482157
482400
Fuse, 15 Amp
Switch, PTO
Wire Harness, Engine SCR 27KA
Switch, Seat
Switch, Brake & Hopper
Interlock Module
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER
2
1
12
11
3
13
9
14
15
10
8
7
4
1
14
16
6
5
2
1
17
22
21
A
18
1
26
19
20
19
23
25
27
20
32
24
To Frame
16
1
28
29
1
33
25
34
35
30
31
40
41
37
16
38
36
16
54
55
39
16
42
16
A
43
47
44
48
49
51
51
53
52
46
46
45
SCR 2002 HC
50
66
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER
Ref. Part.
No. Number Description
Ref. Part.
No. Number Description
1
2
3
4
5
6
7
04090-02 Pop Rivet, 3/16 x .652
451193 Guide Weldment, Screen
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
422932
423131
Backing Strip, Hinge
Backing Plate, Door Latch
04001-08 Bolt, Hex Head 5/16-18 x 3/4"
481092-01 Plastic Knob, 5/16-18
04003-26 Bolt, Carr. 3/8-16 x 4"
481632 Wheel, Anti-Scalp
451191
451289
461474
Screen Weldment
04021-05 Lock Nut, 3/8-16
Stop Weldment, Screen
Hopper Assembly (Incl. Items 1, 2, 4, 14, 16, 17,
21, 22, 24, 25, 37 & 54)
Split Ring
04001-21 Bolt, Hex Head 3/8-16 x 1-3/4"
04041-07 Flatwasher, 3/8-.391 x .938 x .105
04019-02 Nut, Serr. Flange 1/4-20
04003-02 Bolt, Carr. 1/4-20 x 3/4"
8
481876
43548
9
Pin, Hopper Latch
423017
43546
Bracket, Switch Mounting
Bushing, Hopper Pivot
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
04060-01 Roll Pin
482070
422872
Spring, Door Lock
Mount, Latch Pin
04021-09 Nut, Elastic Stop 3/8-16
04001-62 Bolt, Hex Head 3/8-16 x 3-1/4"
04003-06 Bolt, Carr. 1/4-20 x 1"
422978 Support, Hopper Top
482071
Strap Bucket Stop
04041-22 Flatwasher, 1/4-.258 x .50 x .0598
04019-03 Nut, Serr. Flange 5/16-18
04019-02 Nut, Serr. Flange 1/4-20
04091-01 Pop Rivet, 1/4 x .85
423178
04021-01 Nut, Elastic Stop #10-32
482409 Latch, Hopper
04010-12 Screw, #10-32 x 3/4"
Retainer Strip, Hopper
482073
423130
Pad, Rubber Heat Deflector
Backing PLate, Heat Deflector
04040-14 Flatwasher, 1/4-.312 x .750 x .065
422037
422228
481279
Mount, Transition Chute Rear
Mount, Transition Chute Side
Chute, Transition
04003-06 Bolt, Carr. 1/4-20 x 1"
422871 Latch, Hopper Door
04021-10 Nut, Elastic Stop 5/16-18
451189 Hinge Weldment, Hopper Door
04001-126 Bolt, Hex Head 5/16-18 x 5-1/2"
481092-01 Plastic Knob, 5/16-18
43547
Pin, Hopper Door
04060-08 Roll Pin, .188 x 1-1/2"
04003-12 Bolt, Carr. 5/16-18 x 3/4"
423128
451190
Bracket, Door Latch
Hopper Frame Weldment
04019-02 Nut, Serr. Flange 1/4-20
481973 Door, Hopper
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER ACTUATOR MECHANISM
7
6
2
8
5
4
9
10
11
3
12
11
1
13
30
10
15
16
17
18
19
9
14
27
13
18
8
31
7
26
25
15
24
5
7
20
29
8
25
26
28
24
23
SCR 2002 HA
68
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER ACTUATOR MECHANISM
Ref. Part.
No. Number Description
1
481254
Motor, Actuator
2
04015-05 Capscrew, Socket Head, #10-32 x 1/2"
04031-01 Washer, External
3
4
481285
04021-01 Hex Locknut, Elastic Stop, #10-32
481291 Lever, Actuator
04021-10 Hex Locknut, Elastic Stop, 5/16-18
482072 Rod End, 5/16-24 R.H. Thread
Cap, Plastic
5
6
7
8
9
04040-15 Flatwasher, 5/16 (.375 x .875 x .083)
04020-13 Hex Nut, 5/16-18
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
481354
45799
Bushing, Nylon
Connecting Rod
481344
Spring, Connecting Rod
04001-124 Bolt, Hex Head, 5/16-18 x 7.00"
04001-10 Bolt, Hex Head, 5/16-18 x 1-1/4"
04015-08 Capscrew, Socket Head, #10-32 x 1-1/2"
04050-10 Retainer Ring
48100-04 Bushing, Oilite, .502 ID
48114-05 Grease Fitting
04001-08 Bolt, Hex Head, 5/16-18 x 3/4"
461475
45777
Chute
Actuator Mount
Wire Harness, Hopper
482033
04003-02 Bolt, Carr. 1/4-20 x 3/4"
48030-09 Clamp, Cable, 1/2"
04019-02 Serr. Fl. Hex Nut, 1/4-20
45778
Pivot, Elbow
481408
Seal, Hopper Elbow
04006-01 Body Bolt, 5/16-18 x .81"
04090-02 Rivet
423477
Deflector, Hopper Chute
-NOTE-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT DECALS AND INFORMATION PLATES
3
1
2
DANGER
ROTATING BLOWER
BLADES
STOP ENGINE BEFORE
ENTERING CHUTE
6
4
CONTACT CAN INJURE
482080
5
CUTTING
HEIGHT
WARNING
1
INSTALL BELT COVER BEFORE
OPERATING MACHINE
1-1/2
2
2-1/2
READ OPERATOR'S MANUAL
481039
7
START / DRIVE PROCEDURE
ENGAGE PARKING BRAKE
DISENGAGE MOWER DECK DRIVE
MOVE SPEED SELECTOR HANDLES
TO NEUTRAL POSITION
START ENGINE
RELEASE PARKING BRAKE
SELECT SPEED WITH
SELECTOR HANDLE
3
3-1/2
4
SELECT FORWARD OR REVERSE
DIRECTION WITH HYDRO
CONTROL HANDLES
4-1/2
481863
482167
8
11
9
10
12
13
SCR 2K RD1
70
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT DECALS AND INFORMATION PLATES
Ref. Part
No. No.
Description
1
2
3
4
5
482285
482286
48656
482182
482080
Decal, Danger-Spining Blades
Decal, Warning-Rotating Blades
Decal, Patents
Decal, Blade Bolts LH Thread
Decal, Rotating Blades
6
7
482255
481039
Decal, Parking Brake
Decal, Belt Cover
8
9
482288
482167
Decal, Bystanders & Read Operator’s Manual
Decal, Start and Drive Procedure
10
11
482253
481863
Decal, Forward Speed Selector
Decal, Cutting Height
12
482257
482258
482259
481971
48314
Decal, Upper Instrument Panel - Kohler
Decal, Upper Instrumant Panel - Kawasaki
Decal, Lower Instrument Panel
Decal, Heavy Duty
13
14
15
Decal, SCAG
16
17
482052
48406
48318
48319
48404
482251
482447
Decal, Adjustments
Decal, 42" Cutter Deck
Decal, 48” Cutter Deck
Decal, 52" Cutter Deck
Decal, Made in the USA - Metalcraft of Mayville, Inc.
Decal, PTO Engagement
Decal, Driveshaft Grease
18
19
20
R
14
15
17
19
48404
18
20
16
SCR 2K RD2
71
Download from Www.Somanuals.com. All Manuals Search And Download.
KOHLER ELECTRICAL SCHEMATIC
72
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY - COMMERCIAL EQUIPMENT
Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment
of Scag, to be defective in materials or workmanship, will be repaired or replaced by anAuthorized Scag Service Dealer
without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable. Proof of
purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an
Authorized Scag Service Dealer.
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in
materials or workmanship:
* Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days.
* Batteries are covered for ninety (90) days.
* Frame and structural components including oil reservoir, fittings, and oil coolers are warranted for 2 years
(Parts and labor 1st year; Parts only 2nd year).
* Cutter decks are warranted against cracking for a period of three (3) years. (Parts and labor 1st year; Parts
only 2nd and 3rd year) The repair or replacement of the cutter deck will be at the option of Scag Power
Equipment. We reserve the right to request components for evaluation. This warranty does not cover any
mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way
contrary to the operating instructions as specified in the Operator’s Manual.
* Engines and electric starters are covered by the engine manufacturer’s warranty period.
* Major drive system components are warranted for two (2) years by Scag Power Equipment. (Parts and labor 1st
year; Parts only 2nd year) (Two year warranty exclude fittings, hoses, drive belts). The repair or replacement of
the hydraulic pump or hydraulic motor will be at the option of Scag Power Equipment. This warranty does not
cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in
any way contrary to the operating instructions as specified in the Operator’s Manual.
* Electric clutches have a Limited Warranty for 2 year (Parts and labor 1st year; Parts only 2nd year).
* Cutter Spindle Assemblies 46631 have a Limited Warranty for three years (Parts and labor 1st year; Parts
only 2nd and 3rd year).
* Any Scag product used for rental purposes is covered by a 90 day warranty.
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty
period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner
after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of
breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has
been operated in any way contrary to the operating instructions as specified in the Operator’s Manual. The warranty
does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have
not been assembled or installed as specified in the Operator’s Manual and Assembly Manual. The warranty does not
cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment
of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability.
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obliga-
tion to modify any mower previously manufactured.All other implied warranties are limited in duration to the two (2) year
warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied warranties
including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration
of the appropriate two year or ninety day warranty period. Scag’s obligation under this warranty is strictly and exclusively
limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them
any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for
gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner,
mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being
performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconve-
nience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limita-
tion or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2002
PART NO. 03103
PRINTED 3/02
PRINTED IN USA
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
KAWASAKI ELECTRICAL SCHEMATIC
WHITE/BLACK
WHITE/BLACK
73
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Bush Hog Lawn Mower RBX User Manual
Craftsman Lawn Mower 917258911 User Guide
Cub Cadet Lawn Mower 19A40002100 User Guide
Dixon Lawn Mower Accessory 539 131305 User Guide
Exmark Lawn Mower 4500 872 User Guide
Husqvarna Lawn Mower Accessory 968999211 User Guide
Snapper Lawn Mower 21407T User Manual
Snapper Lawn Mower CP21559BV User Manual
Snapper Lawn Mower V2104 User Manual
Stiga Lawn Mower Accessory 46 S COMBI User Guide