Land Pride Lawn Mower 701 069A User Guide

Lift Motor, Snow Blade  
Assembly Instructions  
Treker NT & ST TrekerSeries  
Manual No. 701-149M  
THANK YOU FOR YOUR PURCHASE OF OUR SNOW  
PLOW  
Before You Start  
ENCLOSED IN THIS KIT IS THE UNIVERSAL  
ELECTRIC LIFT HARDWARE 701-069A  
When you see this symbol, the subsequent  
instructions and warnings are serious - follow  
without exception. Your life and the lives of  
others depend on it!  
!
TO HAVE A COMPLETE PLOW ASSEMBLY, YOU  
MUST HAVE AT LEAST FOUR BOXES:  
1. MODEL SPECIFIC ATTACHING HARDWARE KIT.  
TO ATTACH UNIVERSAL PUSH TUBE TO  
MACHINE.  
IMPORTANT: Before you begin, read these  
instructions and check to be sure all parts and tools  
are accounted for. Please retain these installation  
instructions for future reference and parts ordering  
information.  
2. UNIVERSAL PUSH TUBE  
3. BLADE OF YOUR CHOICE (COLOR, STYLE, &  
SIZE)  
Your Lift Motor, Snow Blade is exclusively designed for  
your Land Pride NT & ST Treker. Please read these  
installation instructions and your NT & ST Treker  
Operator’s Manual thoroughly before beginning.  
Especially read information relating to safety concerns.  
Also included in the Operator’s Manual is important  
information on operation, adjustment, troubleshooting,  
and maintenance for this attachment (some manual  
sections do not apply to all accessories).  
4. YOUR CHOICE OF BLADE LIFT METHODS,  
A. ELECTRIC BLADE LIFT  
B. USE YOUR WINCH TO RAISE AND LOWER YOUR  
BLADE.  
OPERATING INSTRUCTIONS READ BEFORE  
OPERATING  
CUSTOMER MUST RECEIVE COPY OF OPERATING  
INSTRUCTIONS AT TIME OF SALE.  
General Information  
These assembly instructions apply to the following Lift  
Motor, Snow Blade Accessories listed below:  
!
DANGER  
at a slow speed.  
Exercise EXTREME CAUTION when plowing and always  
701-069A  
Lift Motor, Snow Blade  
Further Assistance  
!
WARNING  
Your dealer wants you to be satisfied with your new Lift  
Motor, Snow Blade. If for any reason you do not  
understand any part of this manual or are not satisfied  
with the service received, the following actions are  
suggested:  
TO AVOID SERIOUS INJURY OR DEATH:  
1. DO NOT EXCEED 5 MPH WITH BLADE  
INSTALLED.  
2. OPERATE WITH EXTREME CAUTION ON  
SLOPES, STEEP GRADES AND ROUGH  
TERRAIN.  
1. Discuss the matter with your dealership service  
manager making sure he is aware of any problems  
you may have and that he has had the opportunity to  
assist you.  
3. KEEP AWAY FROM BLADE AND MOVING PARTS  
DURING OPERATION.  
2. If you are still not satisfied, seek out the owner or  
general manager of the dealership, explain the  
problem and request assistance.  
4. WHEN PLOWING SNOW OR DIRT INTO A PILE  
START BACKING UP BEFORE RAISING THE  
BLADE.  
3. For further assistance write to:  
5. DO NOT RAM THE BLADE INTO THE PILE. **  
SLOW DOWN BEFORE HITTING PILE. **  
Land Pride Service Department  
1525 East North Street  
P.O. Box 5060  
6. BE AWARE OF POSSIBLE HIDDEN OBJECTS  
UNDER SNOW.  
Salina, Ks. 67402-5060  
E-mail address  
© Copyright 2007  
Printed  
06/21/07  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Land Pride  
Assembly Instructions  
Attach the Lift Strap (#6) to the front of the machine. The  
Strap needs to be secured to the machine in such a  
manner that it will support the Blade and be as close to  
straight above the Cable Spool of the Electric Lift as  
possible. Have the end of the Lift Strap (#6) be roughly  
20" above the ground.  
Attach the 3/16" Quick Link (#8) to the end of the Lift  
Strap as shown. Do not attach the cable at this time.  
06/21/07  
Manual No. 701-149M  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Assembly Instructions  
Route the Red and Black wires to the battery.  
These wires must be well clear of any moving parts on  
the machine  
Do not allow the wires to come in contact with any hot  
parts of the machine, such as the exhaust or cylinder  
head.  
Secure the ring terminal on the black wire to the battery  
negative post.  
Install the ring terminal on the red-white wire to the  
positive battery terminal.  
Route the red and brown leads of the Wiring Harness  
(#27) to the front of the machine and connect to the lift  
motor plug.  
These wires must be well clear of any moving parts of the  
machine  
Switch Installations  
Choose a place for the switch assembly that is free  
from obstructions and does not interfere with the  
normal functions of the machine.  
Do not allow the wires to come in contact with any hot  
parts on the m achine such as the exhaust or cylinder  
head  
Method One:  
Allow plenty of slack for vertical movement of the plow  
between the tie point on the machine and the electric lift  
motor.  
Place the 13/16 Vinyl Coated Cable Clamp (#16) around  
machine’s front rack and secure using one 10-3/4" Pan  
Plug the Relay (#13) into the relay socket on the Wiring  
Harness (#12).  
head Bolt (#19), #10 Star Washer (#17), 5mm Flat  
Washer (#18), 10-24 Nylock Nut.  
With a 12-volt test light or meter locate a wire that is only  
hot when the ignition switch is in the "on" position.  
Method Two:  
This method you will not use the Switch Housing (#14).  
Locate a convenient place on the dash to mount the  
Use the blue scotch lock (#22) tap connector to connect  
the yellow wire from the electronic module to this wire.  
switch. Cut a rectangular hole 7/8" x 1 ". Press the switch  
into the rectangular hole. See picture below.  
Note: Failure to connect the yellow wire to a wire that is  
energized only when the ignition switch is in the "on"  
position, will discharge the battery.  
Check your electrical connections and make sure there  
Manual No. 701-149M  
06/21/07  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Assembly Instructions  
is a fuse in the fuse holder. Turn the key switch to the on  
position and test run the lift motor by pressing the up  
button on the handlebar switch.  
Run the spool in the direction necessary to end up with  
one wrap of cable on the spool and the cable to the front  
side of the spool.  
Verify that pressing the up button on the handle bar  
switch causes clockwise rotation of the spool when  
viewed from the open end. (See illustration below). If the  
spool rotates counterclockwise, see the note on the  
electric lift  
With the blade resting on the ground, route the end of the  
cable up through the quick link (#8) in the lift strap (#6),  
and secure it with the Cable Clamp (#7).  
NOTE: If the Blade is raised too high, the Push  
Tube will contact the ATV frame and put an  
excessive load on the Gear Motor and other parts.  
Failure of the fuse may result. Stop the blade at a  
point before this contact occurs.  
wiring harness diagram on the previous page. The spool  
should now rotate in the clockwise direction when  
pressing the top button.  
ALSO: Be aware that if the switch is held in the  
"DOWN" position after the Blade has contacted the  
ground, the cable will start to wind up backwards on  
the Spool.  
A drop of oil on each end of the spool will keep the  
spool lubricated. Do this periodically  
06/21/07  
Manual No. 701-149M  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Listing of Parts  
Kit No. 701-069A  
ELECTRIC LIFT KIT  
Item  
Part No.  
Part Description  
Qty  
1
2
3
4
5
6
7
8
EL100B  
EL120  
EL121A  
EL113  
EL122A  
PUR1481  
CC18  
U605  
EL123  
EL124  
802-152C  
802-017C  
ELRELAY  
WNRSHOUSING SWITCH HOUSING  
WNRSWITCH-3 R-3 SWITCH  
CVC1316  
SW10  
FW5MM  
801-021C  
800-112C  
839-288C  
SCOTCHLOCK SCOTCH LOCK  
EL136  
EL119  
STS10-212  
EL137  
GEAR MOTOR  
GEAR PULLEY  
MOTOR MOUNT PLATE  
1 1/4" SPACER  
BRG PLATE  
1
1
1
4
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
LIFT STRAP  
1/8" CABLE CLAMP  
3/16" QUICK LINK  
36" CABLE  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
27  
28  
O-RING  
HHCS 1/4-20X2 GR5  
HHCS 3/8-16X1 GR5  
RELAY  
13/16" CABLE CLAMP  
#10 STAR WASHER  
5 MM FLAT WASHER  
SCREW RD HD 10-24 X 3/4 PLT  
CABLE TIE .19X7.25 1.75D 50LB  
20 AMP FUSE (5 PACK)  
O-RING  
ELECTRIC LIFT PIG TAIL  
#10 2-1/2" SELF TAPPING SCREW  
WIRING HARNESS  
SCREW HEX  
801-172C  
Manual No. 701-149M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06/21/07  
6
 

Cub Cadet Lawn Mower 19A40002100 User Guide
Husqvarna Lawn Mower 11 Bio User Guide
McCulloch Lawn Mower M5553D User Guide
Poulan Lawn Mower 184433 User Guide
Snapper Lawn Mower 2 User Manual
Snapper Lawn Mower 1600202 User Guide
Snapper Lawn Mower MR216518B MRP216518B User Manual
Snapper Lawn Mower RP20500 User Manual
Stiga Lawn Mower 23 5337 17 User Guide
Troy Bilt Lawn Mower 13040 18HP User Guide