Cisco Systems Lawn Mower MEM C6K ATA 1 64M User Manual

Catalyst 6500 Series Supervisor Engine Flash PC  
Card Installation Note  
Product Numbers:  
MEM-C6K-FLC16M(=)  
MEM-C6K-FLC24M(=)  
MEM-C6K-FLC64M(=)  
MEM-C6K-ATA-1-64M(=)  
This installation note contains the procedure to install a Flash PC card in the Catalyst 6500 series  
supervisor engines.  
Note  
The 64-MB ATA Flash PC card (MEM-C6K-ATA-1-64M) requires Supervisor Engine 2 with ROMMON  
software release 7.1(1) or later releases. For ROMMON software upgrade details, refer to  
The ATA Flash PC card is supported on Catalyst 6500 series switches running Cisco IOS Release  
12.1(8a)EX or later releases on both the supervisor engine and the Multilayer Switch Feature Card  
(MSFC).  
The ATA Flash PC card is supported on Catalyst 6500 series switches running Catalyst software  
release 7.5(1) or later releases on the supervisor engine and Cisco IOS on the MSFC.  
Note  
The 64-MB linear Flash PC card (MEM-C6K-FLC64M) is supported only on Supervisor Engine 1 and  
requires ROMMON software release 5.3(1) or later releases.  
The 64-MB linear Flash PC card is supported on Catalyst 6500 series switches running Cisco IOS  
Release 12.1(13)E4 or later releases on both the supervisor engine and the MSFC.  
The 64-MB linear Flash PC card is supported on Catalyst 6500 series switches running Catalyst software  
release 7.5(1) or later releases on the supervisor engine and Cisco IOS software on the MSFC.  
Co rp o ra t e He a d q u a rt e rs :  
Cis c o S ys t e m s , In c ., 1 7 0 We s t Ta s m a n Drive , S a n J o s e , CA 9 5 1 3 4 -1 7 0 6 US A  
© 1999–2005 Cisco System s, Inc. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preventing Electrostatic Discharge Damage  
Figure 1  
Supervisor Engine Flash PC Card Slot  
Switch load  
display  
PCMCIA LED  
LINK LEDs  
CONSOLE port  
WS-X6K-SUP1  
Switch Load  
100%  
CONSOLE  
PORT  
PORT  
1
PORT  
2
MODE  
CONSOLE  
PCMCIA  
EJECT  
1%  
SUPERVISOR I  
CONSOLE PORT MODE  
switch  
Status LEDs  
PCMCIA slot  
1000BASE-X GBIC Uplink Ports  
RESET button  
For information about using the PCMCIA Flash PC cards, see the “Using Flash PC Cards” section on  
page 6.  
Preventing Electrostatic Discharge Damage  
Follow these guidelines to prevent electrostatic discharge (ESD) damage:  
Always use an ESD wrist or ankle strap, and ensure that it makes good skin contact.  
Connect the equipment end of the strap to the ESD connector on the switch.  
Place a removed Flash PC card on an antistatic surface or in a static shielding bag. If the card will  
be returned to the factory, immediately place it in a static shielding bag.  
Avoid contact between the card and clothing. The wrist strap only protects the card from ESD  
voltages on the body; ESD voltages on clothing can still cause damage.  
Caution  
For safety, periodically check the resistance value of the antistatic strap. The measurement should be  
between 1 and 10 megohms.  
Installing and Removing a Flash PC Card  
Before you install a Flash PC card, verify that the card’s write-protect switch is off. When the card is  
oriented with the printing side up and the edge connector end away from you, the write-protect switch  
is located on the front edge of the card, as shown in Figure 2.  
Note  
Not all Flash PC cards have the write-protect switch.  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing and Removing a Flash PC Card  
Figure 2  
Locating the Flash PC Card Write Protection Sw itch  
Flash PC card  
shown with write  
protection off  
Flash PC card  
write protection  
Flash PC card  
To install and remove a Flash PC card (see Figure 3), perform these steps:  
You can insert and remove the Flash PC card with the power on.  
Connect an ESD-preventive strap to the ESD connector on the switch.  
Note  
Step 1  
Step 2  
Face the front panel of the switch, and hold the Flash PC card with the connector end toward the slot, as  
shown in Figure 3a.  
Step 3  
Insert the card into the slot until it completely seats in the connector at the back of the slot and the eject  
button pops out toward you, as shown in Figure 3b.  
Note  
The card does not insert all the way inside the slot; a portion of the card remains outside the slot.  
Do not attempt to force the card past this point.  
Step 4  
Step 5  
To eject a Flash PC card, press the ejector button until the card is free of the connector at the back of the  
slot, as shown in Figure 3c.  
Remove the card from the slot and place it in an antistatic bag.  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installing and Removing a Flash PC Card  
Figure 3  
Installing and Rem oving a Flash PC Card  
WS-X5530  
100%  
SUPERVISOR ENGINE  
I
I
I
CONSOLE  
AUX  
d  
EJECT  
a
WS-X5530  
100%  
SUPERVISOR ENGINE  
I
I
I
CONSOLE  
AUX  
Switch Load  
PCMCIA  
EJECT  
b
WS-X5530  
100%  
SUPERVISOR ENGINE  
I
I
I
CONSOLE  
AUX  
Switch Load  
ECT  
c
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using Flash PC Cards  
Using Flash PC Cards  
Note  
An MS-DOS formatted ATA Flash PC card or linear Flash PC card can be accessed successfully  
(including the dir command) with the Catalyst and Cisco IOS operating systems but will not boot from  
ROMMON.  
Note  
The 16-MB MEM-C6K-FLC16M and 24-MB MEM-C6K-FLC24M linear Flash PC cards are formatted  
for the Catalyst 6500 series supervisor engines and are ready to use.  
The MEM-C6K-ATA-1-64M and 64-MB MEM-C6K-FLC64M Flash PC cards are not formatted. You  
must format these cards (see Table 1 on page 7 for a description of the format command.) When you enter  
the dir disk0: or dir slot0: commands, an unformatted Flash PC card returns a “bad device block info” or  
“invalid magic number” error message.  
Note  
Supervisor Engine 1 and Supervisor Engine 2 do not support the same Flash PC card format. To use a  
Flash PC card with Supervisor Engine 2, you must format the card with Supervisor Engine 2. To use a  
Flash PC card with Supervisor Engine 1, you must format the card with Supervisor Engine 1.  
Table 1 Table 1Table 1Table 1shows many of the commands that are available for using and managing  
Flash devices, including the Flash PC cards. To perform specific tasks, use these commands either alone  
or combined with other commands. For example, to copy a file from a TFTP server to a Flash PC card,  
set the BOOT environment variable so that the system will boot from this new image and then verify the  
boot sequence as shown in the following steps:  
Note  
Note  
The following commands listed in Table 1 are not applicable to the ATA Flash (disk0:) PC card:  
undelete, squeeze, show flash devices, show flash, and verify.  
The ATA Flash PC card is accessed through disk0: and the 16-MB, 24-MB, and 64-MB Flash PC cards  
are accessed through slot0:. The following procedure uses slot0:.  
Step 1  
Step 2  
Step 3  
Copy a file from a TFTP server to the Flash PC card in slot0:  
Console (enable) copy tftp slot0:  
Set the BOOT environment variable so that the system boots from slot0:  
Console (enable) set boot system flash slot0:cat6000-sup-5-1-1-CSX.bin prepend  
Display the contents of the BOOT environment variable:  
Console (enable) show boot  
For complete descriptions of these commands and how to use them, refer to the Catalyst 6500 Series  
Software Configuration Guide and the Catalyst 6500 Series Command Reference publication.  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using Flash PC Cards  
Table 1  
Com m ands for Using and Managing Flash Devices  
Task  
Command  
Copy a Flash file to a TFTP server, another copy m/device:filename {tftp | flash | m/device:filename |  
Flash device, or to the running  
configuration.  
config}  
Copy a file from a TFTP server to a Flash copy tftp {flash | m/device:filename | config}  
device or to the running configuration.  
Copy a file from Flash memory to a TFTP copy flash {tftp | m/device:filename | config}  
server or to a Flash device, or to the  
running configuration.  
Copy the running configuration to another copy config {flash | m/device:filename | tftp}  
Flash device or to a TFTP server.  
Set the BOOT environment variable.  
set boot system flash device:[filename] [prepend]  
[mod_num]  
Format a Flash PC device.  
format [spare spare-number] [m/]device1: [[device2:]  
[monlib-filename]]  
Specify the boot field in the configuration set boot config-register boot {rommon | bootflash |  
register, which determines the boot  
method the switch will use at the next  
startup.  
system} [mod_num]  
Display the contents of the BOOT  
environment variable.  
show boot [mod_num]  
Clear a specific image from the BOOT  
environment variable.  
clear boot system flash device:[filename] [mod_num]  
clear boot system all [mod_num]  
Clear the entire BOOT environment  
variable.  
Display a list of files on a Flash device.  
dir [[m/]device:][filename] [all | deleted | long]  
Set the default Flash device for the system. cd [[m/][bootflash: | slot0:]]  
Verify the default Flash device for the  
system.  
pwd [mod_num]  
Delete a file on a Flash device.  
Undelete a file on a Flash device.  
delete [[m/]device:]filename  
undelete index [[m/]device:]  
Permanently remove all deleted files on a squeeze [m/]device:  
Flash device.  
Identify the supported Flash devices on the show flash devices  
system.  
Display information about the Flash PC.  
show flash [[m/]device:] [all | chips | filesys]  
verify [[m/]device:] filename  
Verify the checksum of a file on a Flash  
device.  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Additional Documentation  
Additional Documentation  
Refer to the following documents for additional information on supervisor engine Flash devices:  
Release Notes for Catalyst 6500 Series and Cisco 7600 Series Internet Router Supervisor  
Engine 2 ROMMON  
Catalyst 6500 Series Software Configuration Guide  
Catalyst 6500 Series Command Reference  
Obtaining Documentation  
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several  
ways to obtain technical assistance and other technical resources. These sections explain how to obtain  
technical information from Cisco Systems.  
Cisco.com  
You can access the most current Cisco documentation at this URL:  
You can access the Cisco website at this URL:  
You can access international Cisco websites at this URL:  
Product Documentation DVD  
Cisco documentation and additional literature are available in the Product Documentation DVD package,  
which may have shipped with your product. The Product Documentation DVD is updated regularly and  
may be more current than printed documentation.  
The Product Documentation DVD is a comprehensive library of technical product documentation on  
portable media. The DVD enables you to access multiple versions of hardware and software installation,  
configuration, and command guides for Cisco products and to view technical documentation in HTML.  
With the DVD, you have access to the same documentation that is found on the Cisco website without  
being connected to the Internet. Certain products also have .pdf versions of the documentation available.  
The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com  
users (Cisco direct customers) can order a Product Documentation DVD (product number  
DOC-DOCDVD=) from Cisco Marketplace at this URL:  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Documentation Feedback  
Ordering Documentation  
Beginning June 30, 2005, registered Cisco.com users may order Cisco documentation at the Product  
Documentation Store in the Cisco Marketplace at this URL:  
Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m.  
(0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by  
calling 011 408 519-5055. You can also order documentation by e-mail at  
[email protected] or by fax at 1 408 519-5001 in the United States and Canada,  
Documentation Feedback  
You can rate and provide feedback about Cisco technical documents by completing the online feedback  
form that appears with the technical documents on Cisco.com.  
You can send comments about Cisco documentation to [email protected].  
You can submit comments by using the response card (if present) behind the front cover of your  
document or by writing to the following address:  
Cisco Systems  
Attn: Customer Document Ordering  
170 West Tasman Drive  
San Jose, CA 95134-9883  
We appreciate your comments.  
Cisco Product Security Overview  
Cisco provides a free online Security Vulnerability Policy portal at this URL:  
From this site, you can perform these tasks:  
Report security vulnerabilities in Cisco products.  
Obtain assistance with security incidents that involve Cisco products.  
Register to receive security information from Cisco.  
A current list of security advisories and notices for Cisco products is available at this URL:  
If you prefer to see advisories and notices as they are updated in real time, you can access a Product  
Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Obtaining Technical Assistance  
Reporting Security Problems in Cisco Products  
Cisco is committed to delivering secure products. We test our products internally before we release them,  
and we strive to correct all vulnerabilities quickly. If you think that you might have identified a  
vulnerability in a Cisco product, contact PSIRT:  
Emergencies[email protected]  
An emergency is either a condition in which a system is under active attack or a condition for which  
a severe and urgent security vulnerability should be reported. All other conditions are considered  
nonemergencies.  
Nonemergencies[email protected]  
In an emergency, you can also reach PSIRT by telephone:  
1 877 228-7302  
1 408 525-6532  
Tip  
We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive  
information that you send to Cisco. PSIRT can work from encrypted information that is compatible with  
PGP versions 2.x through 8.x.  
Never use a revoked or an expired encryption key. The correct public key to use in your correspondence  
with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page  
at this URL:  
The link on this page has the current PGP key ID in use.  
Obtaining Technical Assistance  
Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco  
Technical Support & Documentation website on Cisco.com features extensive online support resources.  
In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC)  
engineers provide telephone support. If you do not have a valid Cisco service contract, contact your  
reseller.  
Cisco Technical Support & Documentation Website  
The Cisco Technical Support & Documentation website provides online documents and tools for  
troubleshooting and resolving technical issues with Cisco products and technologies. The website is  
available 24 hours a day, at this URL:  
Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user  
ID and password. If you have a valid service contract but do not have a user ID or password, you can  
register at this URL:  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
1 0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Obtaining Technical Assistance  
Note  
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting  
a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &  
Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose  
Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco  
Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by  
product ID or model name; by tree view; or for certain products, by copying and pasting show command  
output. Search results show an illustration of your product with the serial number label location  
highlighted. Locate the serial number label on your product and record the information before placing a  
service call.  
Submitting a Service Request  
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3  
and S4 service requests are those in which your network is minimally impaired or for which you require  
product information.) After you describe your situation, the TAC Service Request Tool provides  
recommended solutions. If your issue is not resolved using the recommended resources, your service  
request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:  
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.  
(S1 or S2 service requests are those in which your production network is down or severely degraded.)  
Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business  
operations running smoothly.  
To open a service request by telephone, use one of the following numbers:  
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)  
EMEA: +32 2 704 55 55  
USA: 1 800 553-2447  
For a complete list of Cisco TAC contacts, go to this URL:  
Definitions of Service Request Severity  
To ensure that all service requests are reported in a standard format, Cisco has established severity  
definitions.  
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You  
and Cisco will commit all necessary resources around the clock to resolve the situation.  
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your  
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco  
will commit full-time resources during normal business hours to resolve the situation.  
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations  
remain functional. You and Cisco will commit resources during normal business hours to restore service  
to satisfactory levels.  
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or  
configuration. There is little or no effect on your business operations.  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
1 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Obtaining Additional Publications and Information  
Obtaining Additional Publications and Information  
Information about Cisco products, technologies, and network solutions is available from various online  
and printed sources.  
Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo  
merchandise. Visit Cisco Marketplace, the company store, at this URL:  
Cisco Press publishes a wide range of general networking, training and certification titles. Both new  
and experienced users will benefit from these publications. For current Cisco Press titles and other  
information, go to Cisco Press at this URL:  
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and  
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,  
technology breakthroughs, and Cisco products and solutions, as well as network deployment and  
troubleshooting tips, configuration examples, customer case studies, certification and training  
information, and links to scores of in-depth online resources. You can access Packet magazine at  
this URL:  
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies  
learn how they can use technology to increase revenue, streamline their business, and expand  
services. The publication identifies the challenges facing these companies and the technologies to  
help solve them, using real-world case studies and business strategies to help readers make sound  
technology investment decisions. You can access iQ Magazine at this URL:  
or view the digital edition at this URL:  
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering  
professionals involved in designing, developing, and operating public and private internets and  
intranets. You can access the Internet Protocol Journal at this URL:  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
1 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Obtaining Additional Publications and Information  
Networking products offered by Cisco Systems, as well as customer support services, can be  
obtained at this URL:  
Networking Professionals Connection is an interactive website for networking professionals to  
share questions, suggestions, and information about networking products and technologies with  
Cisco experts and other networking professionals. Join a discussion at this URL:  
World-class networking training is available from Cisco. You can view current offerings at  
this URL:  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
1 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Obtaining Additional Publications and Information  
This document is to be used in conjunction with the Catalyst 6500 Series Software Configuration Guide and the Catalyst 6500 Series Command Reference publications.  
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and  
iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified  
Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation,  
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ  
Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing,  
ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, TeleRouter, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered  
trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.  
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship  
between Cisco and any other company. (0502R)  
Copyright © 1999–2005, Cisco Systems, Inc.  
All rights reserved.  
Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note  
78-6507-06  
1 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Briggs Stratton Lawn Mower RIDER 11 User Manual
Craftsman Lawn Mower 24728911 User Guide
Husqvarna Lawn Mower ZTH5223 User Guide
McCulloch Lawn Mower M3750SM User Guide
Poulan Lawn Mower 177937 User Guide
Rhino Mounts Lawn Mower FN120 User Guide
Snapper Lawn Aerator 4573 User Guide
Snapper Lawn Mower V210S User Manual
Snapper Lawn Mower Y30120 User Manual
Stiga Lawn Mower 5 96 User Guide