OPERATOR’S
MANUAL
Turboless Triple Catcher
Turboless Triple Catcher
Mfg. No.
1695354
Description
44” & 50” Turboless Triple Catcher
CAUTION: Read and
follow all instructions.
Manual Part No. 1734740
Revision 01
Rev. Date 05/2007
TP 100-4527-01-AT-SMAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Mowing with the Catcher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Storing the Catcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Mounting Plates & Spacers (Broadmoor/1600/2600/LT Series) . . . . 5
Install Mounting Spacers (Conquest/1700/2700/YT
& Prestige/1800/2800/GT Series . . . . . . . . . . . . 5
Remove Blowout Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install Baffles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Install Bag and Cover Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install Hitch and Upright Support Assembly . . . . . . . . . . . . . . . . . . . . . . . 10
Install Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install Collector Bags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Install Lower Discharge Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Install Upper Tube to Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install Middle Tube. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Normal Removal & Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL WARNINGS
• Know the unit’s controls and how to stop quickly.
READ THE OPERATOR’S MANUALS.
periodically for tears, holes, or weak spots and
replace with a new bag that meets manufacturer’s
durability standards.
• Read and obey all safety decals.
• Only allow responsible adults, who are familiar with
the instructions, to operate the unit.
• Disengage the PTO. Shut off the engine and wait
for all moving parts to stop before attaching,
adjusting, or disconnecting any part of the
collection system.
• If the mower stalls or the collector chute plugs:
1. Disengage the PTO;
2. Stop the engine and remove the key;
3. Set the parking brake, and wait for all moving
parts to stop.
4. Remove the foreign object or clear the chute
with a piece of wood before restarting the engine.
NEVER place hands into COLLECTOR OR
MOWER housing to clear jammed objects.
Blower OR MOWER may rotate when object is
removed.
• Check the collection system to make sure it is
bolted tightly to the unit.
• DO NOT operate the unit without either the entire
grass catcher or the deflector in place.
• Turn off the PTO to disengage the blades when not
mowing.
• DO NOT mow in reverse unless absolutely
necessary. Always look down and behind before
and while travelling in reverse.
• DO NOT turn sharply when travelling alongside a
building or any object. Slow down before turning.
• DO NOT carry passengers.
• When collection system is removed from the
mower deck, the deflector must be properly
installed.
• For added stability and to prevent tipping or loss of
control:
a. Use reduced speed on uneven ground and
when turning corners.
b. Reduce loads on hillsides. It is recommended
that the collection system be kept only half full
when negotiating any slopes. Start mowing on
slopes when the collection system is empty.
c. Mow up and down the face of slopes; never
across the face of any slope.
• Collector bags are subject to deterioration and
wear during normal use. Inspect the bag
• Never operate on slopes greater than 17.6%
(10°).
SAFETY DECALS
These labels are easily applied and will act as a
constant visual reminder to you, and others who may
use the equipment, to follow the safety instructions
necessary for safe, effective operation.
This unit has been designed and manufactured to
provide you with the safety and reliability you would
expect from an industry leader in outdoor power
equipment manufacturing.
Attachment Decal
Although reading this manual and the safety
instructions it contains will provide you with the
necessary basic knowledge to operate this equipment
safely and effectively, we have placed several safety
labels on the unit to remind you of this important
information while you are operating your unit.
WARNING
Thrown objects hazard
• Objects thrown by the mower can seriously
injure or kill you.
• Do not open the hopper while the mower blades
are turning.
All DANGER, WARNING, CAUTION and
instructional messages on your rider, attachments
and mower should be carefully read and obeyed.
Personal bodily injury can result when these
instructions are not followed. The information is for
your safety and it is important! The safety decals
below are on your product.
• Do not operate the mower without the complete
catcher in place.
1732819
Decal - WARNING Thrown
Objects Hazard
Part Number 1732819
If any decals are lost or damaged, replace them at
once. See your local dealer for replacements.
Read and obey all operation and warning decals.
TP 600-2562-01-AT-SMA
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation
Clear the lawn of all sticks, stones, wire and other
debris which may be caught or thrown by the mower
blades.
Check grass condition. If wet, wait until later in the
day. If grass is wet, the grass catcher is likely to
become plugged.
For efficient bagging, air circulation under the
mower deck, through the chute and into the bag
is very important.
For this reason, BEFORE YOU BEGIN MOWING you
should make certain the underside of the mower and
the underside of the catcher lid are free from grass
and debris.
Make sure that there is a snug fit between mower
deck, blower housing, tubes, and grass catcher cover.
Mowing with the Catcher
Always operate with throttle at full speed when
mowing.
CAUTION
Before you begin operating the unit be certain
you have read all of the safety and operational
information of this instruction sheet, as well as
the Operator’s Manual for the tractor and any
other attachments.
Grass should be cut often, and not too short. If grass
is too long or lush it may be necessary to keep
ground speed to a minimum or to cut only half the
width of the mower to prevent clogging. If grass is
long, operate with mower in high cutting position for
first pass, cutting again in a lower position on a
second pass.
Never operate on slopes greater than 17.6% (10°).
Do not open the cover with mower engaged.
After Operation
Remove any debris from the the screen on the
underside of the lid.
If a large amount of cut grass is spilling out from
under deck, the tube may be plugged or the bags
may be full— discontinue mowing, stop the unit,
disengage the PTO, shut off the engine and then
empty the catcher or clear the tube.
The blower housing and tube should be removed for
cleaning.
Inspect the grass bags for wear or damage. Make
sure that there is a snug fit between mower deck,
blower housing, tubes, and grass catcher cover.
WARNING
ALWAYS shut off the tractor. Disengage the
PTO, and allow all moving parts to stop
BEFORE disconnecting or clearing tube, or
emptying catcher.
Storing The Grass Catcher
Clean the grass catcher thoroughly using a mild
detergent (other products may damage the tube).
Remove any debris from the screen on the underside
of the lid.
Before leaving the operator’s position for any
reason, engage the parking brake, disengage
the PTO, stop the engine and remove the key.
If paint has been scratched on metal parts, touch up
with paint, or apply a thin film of oil to prevent
corrosion.
To reduce fire hazard, keep the engine, rider
and mower free of grass, leaves and excess
grease. Do not stop or park rider over dry
leaves, grass or combustible materials.
Store in a dry area. Dry thoroughly before storing for
a long period of time. Always store away from
moisture.
CAUTION
Do not leave grass in bagger containers.
Empty containers after each use and before
storing. Failure to do so may result in
spontaneous combustion which could develop
into a fire.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
INSTALL MOUNTING PLATES -
BROADMOOR / 1600 / 2600 / LT
SERIES
A
B
C
D
Install Plates & Spacers
1. Mount the side brackets (C, Figure 1) to both
sides of the frame using the holes shown. Secure
with one 3/8-16 x 1 capscrew (D), 3/8 lockwasher
(B), and 3/8-16 nut (A) per side.
Figure 1. Install Side Brackets
A. Nut, 3/8-16
B. Lockwasher, 3/8
C. Side Bracket
2. Install the rear spacers (C, Figure 2). Secure with
two 1/2-13 x 2-1/2 capscrews (E), washers (D),
spacers (C), and 1/2-13 nylock nuts (A) per side.
D. Capscrew, 3/8-16 x 1
A
C
D
D
B
Figure 2. Install Rear Spacers
A. Nylock Nuts, 1/2-13
B. Capscrew, 1/2-13 x 2-1/2
C. Spacers
D. Washers, 1/2
INSTALL MOUNTING SPACERS -
CONQUEST / 1700 / 2700 / YT &
PRESTIGE / 1800 / 2800 / GT
SERIES
A
C
D
Install Spacers
1. Install the rear spacers (C, Figure 3). Secure with
two 1/2-13 x 2-1/2 capscrews (E), washers (D),
spacers (C), and 1/2-13 nylock nuts (A) per side.
B
D
Figure 3. Install Rear Spacers
A. Nylock Nuts, 1/2-13
B. Capscrews, 1/2-13 x 2-1/2
C. Spacers
D. Washers, 1/2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Blowout Baffle
Install Baffles
1.Remove and discard short blowout baffle (C, Figure
4), carriage bolts (B) and locknuts (D) from mower
deck (A).
1. Determine which baffle to use. See Figure 5
Chart.
2. Lift side discharge chute (H, Figure 6).
3. Insert baffle (F) through discharge opening and
position baffle into place.
4. Tighten carriage bolts (A) and nuts (E) on baffle
(F).
5. Tighten carriage bolt (B) and nut (E) on baffle (F).
6. Position baffle (G) into place.
B
D
7. Tighten carriage bolts (C) and nuts (E) on baffle
(G).
A
D
8. Tighten carriage bolts (D) and nuts (E) on baffle
(G).
C
44” Mower Deck
50” Mower Deck
Figure 4. Baffle Removal
A. Mower Deck
B. Carriage Bolts,5/16-18 x 3/4
C. Blowout Baffle, Short
D. Nuts, Whizlock, 5/16-18 x 3/4
“A” RH side 26-1/4” long RH side 29-3/4” long
“B” LH side 24-7/8” long LH side 27-3/4” long
“A”
“B”
Figure 5. Baffle Chart
6
Download from Www.Somanuals.com. All Manuals Search And Download.
H
E
A
A. Carriage Bolts,
5/16-18 x 5/8
B. Carriage Bolt,
5/16-18 x 5/8
E
E
C. Carriage Bolts,
5/16-18 x 5/8
C
F
D. Carriage Bolts,
5/16-18 x 5/8
E
B
D
E
E. Locknut, 5/16-18
F. Right Hand Baffle
G. Left Hand Baffle
H. Discharge Chute
G
Figure 6. Install Baffles
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL LOWER CHUTE ROD AND PIN TO BOOT
Install Components
INSTALL MOUNTING PLATE
1. Insert the head of pin (A, Figure 8) through front
hole of lower chute (D). Secure with 1/4-20 x 5/8
carriage bolt (B) and 1/4-20 lock nut (C) as
shown.
1. Install mounting plate (A, Figure 7) to mower deck
as shown. Secure with 5/16-18 x 5/8 carriage
bolts (C) and 5/16-18 locknuts (A).
2. Install the rod (H) to lower chute (D) using 5/16-18
x 1 capscrew (J) and 5/16-18 locknut (G) for front
holes. Use 5/16-18 x 1-1/4 capscrew (I) and 5/16-
18 locknut (G) as shown. Tighten hardware.
3. Install the rubber strap (F) onto capscrew (I)
securing with 5/16-18 locknut as shown.
A
C
C
B
B
A
D
E
F
G
Figure 7. Install Mounting Plate
A. Mounting Plate
G
B. Locknuts, 5/16-18
C. Carriage Bolts, 5/16-18 x 5/8
H
J
I
Figure 8. Install Lower Chute and Pin to Boot
A. Pin, Latch
B. Carriage Bolt, 1/4-20 x 5/8
C. Locknut, 1/4-20
D. Lower Chute
E. Locknut, Center Lock, 5/16-18
F. Strap, Rubber
G. Locknuts, Whiz Lock, 5/16-18
H. Rod, Boot Mount
I. Capscrew, Hex Head, 5/16-18 x 1-1/4
J. Capscrew, Hex Head, Thin, 5/16-18 x 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL HANDLE TO TUBE
1. Install handle (A, Figure 9) using 1/4-20 x 1/2
screw and 1/4-20 locknut (B) for rear hole. Use
1/4-20 x 1 screw (D) as shown. Tighten hardware.
2. Install strap (E) to screw (D) securing with 1/4-20
locknut (F).
F
B
A
E
C
B
D
Figure 9. Install Handle to Tube
A. Handle
B. Locknuts, KEPS, 1/4-20
C. Screw, Slotted, 1/4-20 x 1/2
D. Screw, Slotted, 1/4-20 x 1
E. Strap, Rubber
F. Locknut, Center Lock, 1/4-20
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL BAG AND COVER SUPPORT
INSTALL COVER ASSEMBLY
1. Install the bag and cover support (B, Figure 10) to
upright support (A) using reinforcement plate (C)
and 3/8-16 x 1 capscrews (D) and 3/8-16 locknuts
(E) as shown.
1. Attach cover assembly (B, Figure 12) to bag
support bracket (A) using hinge pivots (E). Secure
cover using cover hinge pins (C) and hair pins (D)
as shown.
B
B
E
C
D
E
D
A
A
C
D
E
C
Figure 10. Install Bag and Cover Support
A. Upright Support
B. Bag and cover Support
C. Reinforcement Plate
D. Capscrews, 3/8-16 x 1
E. Locknuts, 3/8-16
Figure 12. Install Cover Assembly
A. Bag Support Bracket
B. Cover Assembly
C. Cover Hinge Pins
D. Hair Pins
E. Hinge Pivots
INSTALL HITCH AND UPRIGHT SUPPORT ASSEMBLY
1. Attach hitch and upright support assembly (A,
Figure 11) to frame spacers (B) as shown.
A
B
B
Figure 11. Attach Hitch and Upright Support
A. Hitch and Upright Support Assembly
B. Frame spacers
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL COLLECTOR BAGS
INSTALL LOWER DISCHARGE CHUTE
1. Raise the cover (A, Figure 13).
1.Lift discharge deflector up (D, Figure 14).
2. Insert lower chute rod (A) into mounting plate (B).
2. Attach collector bags (B) using grass bag hanger
(C) to bag hanger post (D).
3. Pull rubber strap (C) and secure by placing hole
closest to knob in strap completely over locknut
(E).
A
C
D
C
E
D
A
B
B
Figure 13. Install Collector Bags
A. Cover
B. Collector Bag
C. Grass Bag Hanger
D. Bag Hanger Posts
Figure 14. Install Lower Discharge Chute
A. Lower Chute Rod
B. Mounting Plate
C. Rubber Strap
D. Discharge Deflector
E. Locknut
11
Download from Www.Somanuals.com. All Manuals Search And Download.
44” Frame Hung Mowers
50” Frame Hung Mowers
44” Free Floating Mowers
D
50” Free Floating Mowers
C
E
D
F
B
B
A
C
Figure 15. Install Upper Tube to Cover
A. Upper Tube
B. Cover
C. Ridge, Upper Tube
D. Ridge Cutout
A
INSTALLING UPPER & MIDDLE TUBES
Figure 16. Install Middle Tube
A. Lower Chute
B. Strap, Rubber
C. Pin
D. Middle Tube
E. Upper Tube
1. Slide the upper tube (E, Figure 15) into cover (B)
aligning ridge (C) with cutout (D) as shown.
2. See Figure 16 for correct hole location and secure
the upper tube (E) to middle tube using screw (F).
F. Screw, 1/4 x 3/4
2. Slide middle tube (D, Figure 16) into upper tube
(E).
3. Slide middle tube (D) over boot (A). Pull strap (B)
and place hole completely over pin (C).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal Removal & Installation
E
F
R
Q
D
C
D
G
A
B
C
S
P
H
O
S
A. Hitch Support Assembly
B. Cover
C. Pin
D. Hair Pins
E. Bag
F. Grass Bag Hanger
G. Upper Tube
H. Middle Tube
I. Strap, Boot
J. Deflector
J
N
I
K. Nut & Capscrew
L. Mounting plate
M. Lower Chute Rod
N. Lower Chute
O. Pin
P. Strap, Middle
Q. Ridge
R. Ridge Cutout
S. Rear Spacers
K
M
L
Figure 17. Normal Installation & Removal
4. Lift discharge deflector (J) up. Insert lower chute
rod (M) into mounting plate (L). Pull strap (I) and
secure by placing hole closest to knob in strap
completely over locknut and capscrew (K).
Normal Removal & Installation
Collector Installation
Note: See previous pages for more detailed
5. Slide the upper tube (G) into cover (B) aligning
ridge (Q) with cutout (R) as shown.
installation and operation instructions if necessary.
1. Mount the hitch support assembly (A, Figure 17)
onto rear tractor frame spacers (S).
6. Slide middle tube (H) into upper tube (G). Slide
middle tube (H) over lower chute (N). Pull strap
(P) and place hole completely over pin (O).
2. Attach cover (B) to support assembly using pins
(C) and hair pins(D).
3. Pivot cover (B) up. Install bags (E) by attaching
grass bag hanger (F) to support assembly (A).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Collector Removal
WARNING
OPERATION WITHOUT BAGGER
For operation without bagger, the mower
deflector MUST be properly installed in the
down position and retained by the spring latch.
1. Unhook strap (P, Figure 17) from pin (O). Slide
middle tube (H) into upper tube (G) and remove
middle tube (H). Remove upper tube (G) from
cover (B).
2. Lift up cover (B) remove and empty bags (E).
3. Unhook strap (I) from locknut and capscrew (K).
Remove lower chute (N) from mounting plate (L).
See that the discharge deflector (J) returns to the
DOWN position.
4. Remove hair pin (D) and pins (C) then remove
cover (B).
Note: To prevent loss of parts, reinstall pins (C) and
hair pins (D) in support assembly hinge pivots (E,
Figure 17).
5. Remove hitch support assembly (A) from rear
frame spacers (S).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
PRODUCTS
535 Macon Street
McDonough, GA 30253
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
AGCOLawn.com
Briggs & Stratton Yard Power Products Group
Copyright © 2007 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
|